Yamaha CC-50 Owner`s manual

Yamaha CC-50 Owner`s manual
RINTED IN TAIWAN
006 .07 - 0.8 * 1 !
(E)
1
2
3
4
5
6
7
OWNER’S MANUAL 8
9
XC50W
3D1-F8199-11
LIT-11626-20-36
3D1-F8199-11cv.pmd
3
2006/05/15, 19:10
1
2
3
4
EAU10041
5
6
7
8
9
3D1-F8199-11ch0SGML.pmd
1
2006/05/15, 19:02
EAU10050
INTRODUCTION
EAU10090
Congratulations on your purchase of the Yamaha VINO. This model is the result of Yamaha’s vast experience in the production
of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that
have made Yamaha a leader in these fields.
1
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you have
any questions concerning the operation or maintenance of your scooter, please consult a Yamaha dealer.
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at the
date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
scooter. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
2
3
4
5
6
7
8
9
3D1-F8199-11ch0SGML.pmd
2
2006/05/15, 19:02
EAU10120
IMPORTANT MANUAL INFORMATION
EAU35821
Particularly important information is distinguished in this manual by the following notations:
1
2
3
4
5
6
Q
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
w
Failure to follow WARNING instructions could result in severe injury or death to the scooter
operator, a bystander, or a person inspecting or repairing the scooter.
cC
A CAUTION indicates special precautions that must be taken to avoid damage to the scooter.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
NOTE:
8 This manual should be considered a permanent part of this scooter and should remain with it even if the scooter is
subsequently sold.
8 Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your scooter and
this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
7
EWA12580
8
9
w
PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY AND
COMPLETELY BEFORE OPERATING THIS SCOOTER. DO NOT ATTEMPT TO OPERATE THIS SCOOTER UNTIL YOU
HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL YOU HAVE
BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND
THE RELIABILITY OF THIS SCOOTER.
*Product and specifications are subject to change without notice.
3D1-F8199-11ch0SGML.pmd
3
2006/05/15, 19:02
IMPORTANT MANUAL INFORMATION
1
2
3
AFFIX DEALER
4
LABEL HERE
5
6
EAUT1390
VINO
OWNER’S MANUAL
©2006 by Yamaha Motor Taiwan Co., Ltd.
1st edition, July 2006
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Taiwan Co., Ltd.
is expressly prohibited.
Printed in Taiwan.
3D1-F8199-11ch0SGML.pmd
4
2006/05/15, 19:02
7
8
9
EAU10210
TABLE OF CONTENTS
SAFETY INFORMATION .............. 1-1
Further safe-riding points ........... 1-4
Location of important labels ....... 1-5
1
2
DESCRIPTION ............................. 2-1
Left view .................................... 2-1
Right view .................................. 2-2
Controls and instruments ........... 2-3
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL
FUNCTIONS ................................. 3-1
Main switch/steering lock ........... 3-1
Indicator and warning lights ........ 3-2
Speedometer unit ....................... 3-3
Fuel gauge ................................. 3-3
Handlebar switches .................... 3-3
Front brake lever ........................ 3-4
Rear brake lever ......................... 3-5
Rear wheel lock ......................... 3-5
Fuel tank cap ............................. 3-6
Fuel ........................................... 3-6
Catalytic converter ..................... 3-7
Kickstarter ................................. 3-8
Seat ........................................... 3-8
Helmet holder ............................. 3-9
Front storage compartment ........ 3-9
Storage compartment .............. 3-10
Carrier ...................................... 3-10
Luggage hook .......................... 3-11
3D1-F8199-11ch0SGML.pmd
5
PRE-OPERATION CHECKS ......... 4-1
Pre-operation check list ............. 4-2
OPERATION AND IMPORTANT
RIDING POINTS ........................... 5-1
Starting a cold engine ................ 5-1
Starting off ................................. 5-2
Acceleration and deceleration .... 5-2
Braking ...................................... 5-2
Engine break-in .......................... 5-3
Parking ....................................... 5-3
PERIODIC MAINTENANCE AND
MINOR REPAIR ............................ 6-1
PERIODIC MAINTENANCE ....... 6-1
Maintenance, emission control
Periodic maintenance chart for the
emission control system ......... 6-2
General maintenance and lubrication
chart ....................................... 6-3
Removing and installing the
panel ....................................... 6-6
Checking the spark plug ............. 6-6
Engine oil and oil strainer ........... 6-8
Final transmission oil ............... 6-10
Coolant .................................... 6-11
Replacing the air filter element and
cleaning the check hose ....... 6-12
Carburetor ................................ 6-13
Checking the throttle cable free
play ....................................... 6-13
Tires ........................................ 6-13
Cast wheels ............................. 6-15
Adjusting the brake lever free
play ....................................... 6-15
Adjusting the rear brake lever free
play ....................................... 6-16
Checking the front and rear brake
shoes .................................... 6-16
Checking and lubricating the throttle
grip and cable ....................... 6-17
Lubricating the front and rear brake
levers .................................... 6-17
Checking and lubricating the
centerstand ........................... 6-18
Checking the front fork ............. 6-18
Checking the steering .............. 6-19
Checking the wheel bearings .... 6-19
Battery ..................................... 6-20
Replacing the fuse ................... 6-21
Replacing the headlight bulb .... 6-22
Replacing the tail/brake light
bulb ....................................... 6-23
Replacing a turn signal light
bulb ....................................... 6-24
Troubleshooting ........................ 6-24
Troubleshooting charts ............. 6-25
2006/05/15, 19:02
TABLE OF CONTENTS
SCOOTER CARE AND STORAGE 7-1
Care ........................................... 7-1
Storage ...................................... 7-3
1
SPECIFICATIONS ........................ 8-1
2
CONSUMER INFORMATION ........ 9-1
Identification numbers ................ 9-1
Reporting safety defects ............ 9-3
Motorcycle noise regulation........ 9-4
Maintenance record .................... 9-5
YAMAHA MOTOR CORPORATION,
U.S.A. ..................................... 9-7
RIVA LIMITED WARRANTY ....... 9-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) ................................... 9-9
3
4
5
6
7
8
9
3D1-F8199-11ch0SGML.pmd
6
2006/05/15, 19:02
Safety information<IXE>
EAU10220
Q SAFETY INFORMATION
EAU10240
1
2
3
4
5
6
7
8
9
SCOOTERS ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON
THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY
OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE
RIDING THIS SCOOTER.
HE OR SHE SHOULD:
8 OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
SCOOTER OPERATION.
OBSERVE THE WARNINGS AND
MAINTENANCE REQUIREMENTS IN THE OWNER’S
MANUAL.
8 OBTAIN QUALIFIED TRAINING IN
SAFE AND PROPER RIDING
TECHNIQUES.
8 OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL AND/
OR WHEN MADE NECESSARY
BY MECHANICAL CONDITIONS.
Safe riding
8 Always make pre-operation checks.
Careful checks may help prevent
an accident.
8 This scooter is designed to carry
the operator only. No passengers.
8 The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself conspicuous appears to be very effective in reducing the chance of this
type of accident.
Therefore:
9 Wear a brightly colored jacket.
9 Use extra caution when approaching and passing through
intersections, since intersections are the most likely places
for scooter accidents to occur.
9 Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
8 Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
9 Make sure that you are qualified and that you only lend your
scooter to other qualified
operators.
9 Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
9 We recommend that you
practice riding your scooter
where there is no traffic until
you have become thoroughly
familiar with the scooter and all
of its controls.
8 Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to
EXCESSIVE
SPEED
or
undercornering (insufficient lean
angle for the speed).
9 Always obey the speed limit
and never travel faster than
warranted by road and traffic
conditions.
1-1
3D1-F8199-11ch1SGML.pmd
1
2006/05/15, 19:03
Q SAFETY INFORMATION
9 Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
8 The posture of the operator is important for proper control. The operator should keep both hands on
the handlebar and both feet on the
footboard during operation to maintain control of the scooter.
8 Never ride under the influence of
alcohol or other drugs.
8 This scooter is designed for on-road
use only. It is not suitable for offroad use.
Protective apparel
The majority of fatalities from scooter
accidents are the result of head injuries.
The use of a safety helmet is the single
most critical factor in the prevention or
reduction of head injuries.
8 Always wear an approved helmet.
8 Wear a face shield or goggles. Wind
in your unprotected eyes could contribute to an impairment of vision
that could delay seeing a hazard.
8 The use of a jacket, substantial
shoes, trousers, gloves, etc., is
effective in preventing or reducing
abrasions or lacerations.
8 Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
8 Never touch the engine or exhaust
system during or after operation.
They become very hot and can
cause burns. Always wear protective clothing that covers your legs,
ankles, and feet.
Modifications
Modifications made to this scooter not
approved by Yamaha, or the removal of
original equipment, may render the
scooter unsafe for use and may cause
severe personal injury. Modifications
may also make your scooter illegal to
use.
Loading and accessories
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care when
riding a scooter that has added cargo or
accessories. Here are some general
guidelines to follow if loading cargo or
adding accessories to your scooter:
Loading
The total weight of the operator, accessories and cargo must not exceed the
maximum load limit of 77 kg (170 lb).
When loading within this weight limit,
keep the following in mind:
8 Cargo and accessory weight should
be kept as low and close to the
scooter as possible. Make sure to
distribute the weight as evenly as
possible on both sides of the
scooter to minimize imbalance or
instability.
8 Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely
attached to the scooter before riding.
Check accessory mounts and
cargo restraints frequently.
8 Never attach any large or heavy
items to the handlebar, front fork,
or front fender. Such items can create unstable handling or a slow
steering response.
1-2
3D1-F8199-11ch1SGML.pmd
2
2006/05/15, 19:03
1
2
3
4
5
6
7
8
9
Q SAFETY INFORMATION
1
2
3
4
5
6
7
8
9
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this scooter. Since Yamaha cannot test
all other accessories that may be available, you must personally be responsible
for the proper selection, installation and
use of non-Yamaha accessories. Use
extreme caution when selecting and installing any accessories.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
8 Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully
inspect the accessory before using it to make sure that it does not
in any way reduce ground clearance or cornering clearance, limit
suspension travel, steering travel
or control operation, or obscure
lights or reflectors.
9 Accessories fitted to the
handlebar or the front fork area
can create instability due to
improper weight distribution or
aerodynamic changes. If
accessories are added to the
handlebar or front fork area,
they must be as lightweight as
possible and should be kept to
a minimum.
9 Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to
lift the scooter, or the scooter
may become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
9 Certain accessories can
displace the operator from his
or her normal riding position.
This improper position limits
the freedom of movement of
the operator and may limit
control ability, therefore, such
accessories are not recommended.
8 Use caution when adding electrical
accessories. If electrical accessories exceed the capacity of the
scooter’s electrical system an elec-
tric failure could result, which could
cause a dangerous loss of lights or
engine power.
Gasoline and exhaust gas
8 GASOLINE IS HIGHLY FLAMMABLE:
9 Always turn the engine off
when refueling.
9 Take care not to spill any
gasoline on the engine or
exhaust system when refueling.
9 Never refuel while smoking or
in the vicinity of an open flame.
8 Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a
short time. Always operate your
scooter in an area that has adequate
ventilation.
8 Always turn the engine off before
leaving the scooter unattended and
remove the key from the main
switch. When parking the scooter,
note the following:
9 The engine and exhaust
1-3
3D1-F8199-11ch1SGML.pmd
3
2006/05/15, 19:03
Safe-riding points<IXE>
Q SAFETY INFORMATION
system may be hot, therefore,
park the scooter in a place
where pedestrians or children
are not likely to touch these hot
areas.
9 Do not park the scooter on a
slope or soft ground, otherwise
it may fall over.
9 Do not park the scooter near a
flammable source (e.g., a
kerosene heater, or near an
open flame), otherwise it could
catch fire.
8 If you should swallow any gasoline,
inhale a lot of gasoline vapor, or
allow gasoline to get in your eyes,
see your doctor immediately. If any
gasoline spills on your skin or clothing, immediately wash the affected
area with soap and water and
change your clothes.
EAU10350
Further safe-riding points
8 Make sure to signal clearly when
making turns.
8 Braking can be extremely difficult
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when stopping on a wet surface.
8 Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
8 Be careful when passing parked
cars. A driver might not see you and
open a door in your path.
8 Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become
extremely slippery when wet. Slow
down and cross them with caution.
Keep the scooter upright, otherwise
it could slide out from under you.
8 The brake lining could get wet when
you wash the scooter. After washing the scooter, check the brakes
before riding.
8 Always wear a helmet, gloves, trou-
sers (tapered around the cuff and
ankle so they do not flap), and a
bright colored jacket.
8 Do not carry too much luggage on
the scooter. An overloaded scooter
is unstable. Use a strong cord to
secure any luggage to the carriers.
A loose load will affect the stability
of the scooter and could divert your
attention from the road. (See page
1-1.)
1-4
3D1-F8199-11ch1SGML.pmd
4
2006/05/15, 19:03
1
2
3
4
5
6
7
8
9
Labels, location of<IXE>
Q SAFETY INFORMATION
EAU10381
Location of important labels
Please read the following important labels carefully before operating this vehicle.
1
2
3
3,4,5,6
4
2
5
1
6
7
8
9
1-5
3D1-F8199-11ch1SGML.pmd
5
2006/05/15, 19:03
Q SAFETY INFORMATION
1
4
1
2
2
3
5
4
5
3
6
6
7
8
9
1-6
3D1-F8199-11ch1SGML.pmd
6
2006/05/15, 19:03
Part locations<IXE>
EAU10400
DESCRIPTION
EAU10410
Left view
2
3
4
5
6
1
2
1
3
10
4
5
7
6
9
7
8
9
8
1. Front turn signal light (page 6-24)
2. Luggage hook (page 3-11)
3. Helmet holder (page 3-9)
4. Storage compartment (page 3-10)
5. Fuel tank cap (page 3-6)
6. Rear turn signal light (page 6-24)
7. Kickstarter (page 3-8)
8. Air filter (page 6-12)
9. Battery (page 6-20)
10.Front storage compartment (page 3-9)
2-1
3D1-F8199-11ch2SGML.pmd
1
2006/05/15, 19:04
DESCRIPTION
EAU10420
Right view
1
2
4
3
5
1
2
3
4
5
8
7
6
7
6
8
1.
2.
3.
4.
5.
6.
7.
8.
Tail/brake light (page 6-23)
Carrier (page 3-10)
Seat (page 3-8)
Coolant reservoir (page 6-11)
Headlight (page 6-22)
Spark plug (page 6-6)
Centerstand (page 6-18)
Muffler
9
2-2
3D1-F8199-11ch2SGML.pmd
2
2006/05/15, 19:04
DESCRIPTION
EAU10430
Controls and instruments
2
1
1
3
5
4
2
3
4
5
9
6
6
7
8
7
8
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
Rear brake lever (page 3-5)
Left handlebar switches (page 3-3)
Speedometer unit (page 3-3)
Right handlebar switches (page 3-3)
Front brake lever (page 3-4)
Throttle grip (page 6-13)
Rear wheel lock lever (page 3-5)
Main switch/steering lock (page 3-1)
Fuel gauge (page 3-3)
2-3
3D1-F8199-11ch2SGML.pmd
3
2006/05/15, 19:04
Main switch/steering lock<IXE>
EAU10444
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
Main switch/steering lock
EAU10660
OFF
All electrical systems are off. The key
can be removed.
To unlock the steering
1
EAU10680
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
1
2
2
3
To lock the steering
ZAUM00**
4
ZAUM00**
1. Turn.
2. Release.
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
1
Push the key in, and then turn it to “OFF”
while still pushing it.
w
ZAUM00**
1. Push.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped before turning the key to “OFF” or
“LOCK”.
3-1
3D1-F8199-11ch3SGML.pmd
1
6
EWA10060
EAU10530
ON
All electrical circuits are supplied with
power, the taillight comes on, and the
engine can be started. The key cannot
be removed.
NOTE:
The headlight and meter lighting come
on automatically when the engine is
started.
5
2006/08/17, 18:14
7
8
9
Indicator and warning lights<IXE>
Turn signal indicator lights<IXE>
High beam indicator light<IXE>
Coolant temperature warning light<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU11003
Indicator and warning lights
1
1
2
ECA10020
cC
Do not operate the engine if it is overheated.
EAU11080
3
&”
High beam indicator light “&
This indicator light comes on when the
high beam of the headlight is switched
on.
2
2
4
EAU11030
4” and
Turn signal indicator lights “4
6”
“6
The corresponding indicator light flashes
when the turn signal switch is pushed
to the left or right.
ZAUM00**
EAU11440
5
1. High beam indicator light“&”
2. Turn signal indicator lights“4” and “6”
6
7
1
8
9
ZAUM00**
1. Coolant temperature warning light“
Coolant temperature warning light “ ”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical circuit.
”
3-2
3D1-F8199-11ch3SGML.pmd
2
2006/08/17, 18:14
Speedometer unit<IXE>
Fuel gauge<IXE>
Handlebar switches<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAUT1571
Speedometer unit
EAU12150
Fuel gauge
EAU12343
Handlebar switches
Left
1
1
1
3
1
ZAUM00**
4
ZAUM00**
1. Speedometer
1. Fuel gauge
The speedometer unit is equipped with
a speedometer and an odometer. The
speedometer shows the riding speed.
The odometer shows the total distance
traveled.
The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches the
red line, refuel as soon as possible.
NOTE:
Do not allow the fuel tank to empty itself completely.
ZAUM00**
3
2
3
1. Dimmer switch “%/&“
2. Turn signal switch “4/6”
3. Horn switch “*”
3-3
3D1-F8199-11ch3SGML.pmd
2
2006/08/17, 18:14
5
6
7
8
9
Dimmer switch<IXE>
Turn signal switch<IXE>
Horn switch<IXE>
Engine stop switch<IXE>
Start switch<IXE>
Brake lever, front<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU12500
Right
*”
Horn switch “*
Press this switch to sound the horn.
EAU12900
Front brake lever
EAU12660
1
1
2
3
2
4
5
EAUM1131
ZAUM00**
1. Engine stop switch “#/$“
2. Start switch “,”
EAU12400
6
&/%
%”
Dimmer switch “&
Set this switch to “&” for the high beam
and to “%” for the low beam.
7
8
9
1
#/$
$”
Engine stop switch “#
Set this switch to “#” before starting
the engine. Set this switch to “$” to stop
the engine in case of an emergency, such
as when the motorcycle overturns or
when the throttle cable is stuck.
EAU12460
,”
Start switch “,
Push this switch while applying the front
or rear brake to crank the engine with
the starter.
ECA10050
cC
See page 5-1 for starting instructions
prior to starting the engine.
ZAUM00**
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handlebar grip.
4/6
6”
Turn signal switch “4
To signal a right-hand turn, push this
switch to “4”. To signal a left-hand turn,
push this switch to “6”. When released,
the switch returns to the center position.
To cancel the turn signal lights, push the
switch in after it has returned to the center position.
3-4
3D1-F8199-11ch3SGML.pmd
4
2006/08/17, 18:14
Brake lever, rear<IXE>
Rear wheel lock<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU12950
Rear brake lever
EAUT1551
Rear wheel lock
1
When the rear wheel lock lever is pulled
down to lock the rear wheel, a cover will
close over the main switch keyhole to
help prevent theft.
NOTE:
If the rear wheel lock lever is not easy
to pull downward, rotate the rear wheel
slightly, and then try pulling the lever
again.
1
2
To unlock
Insert the key into the rear wheel lock
release, push it in, and then turn it clockwise. The rear wheel will unlock and the
main switch keyhole cover will open.
ZAUM00**
1. Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handlebar grip.
2
ZAUM00**
6
1. Rear wheel lock lever
2. Rear wheel lock release
7
3-5
5
4
5
1
To lock
1. Place the vehicle on the centerstand.
2. Lock the steering. (See page 3-1.)
3. Remove the key from the main
switch.
4. Pull the rear wheel lock lever downward, and then release it. The rear
wheel will lock and the main switch
keyhole will be covered.
3D1-F8199-11ch3SGML.pmd
3
2006/08/17, 18:14
8
9
Fuel tank cap<IXE>
Fuel<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU32482
Fuel tank cap
1
1
NOTE:
The fuel tank cap cannot be installed
unless the key is in the lock. In addition, the key cannot be removed if the
cap is not properly installed and locked.
2
EAU13210
Fuel
1
EWA10130
w
3
Make sure that the fuel tank cap is
properly installed before riding.
2
4
5
6
7
ZAUM00**
ZAUM00**
1. Fuel tank cap lock cover
2. Match marks
1. Fuel tank filler tube
Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown.
To remove the fuel tank cap
Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released and
the fuel tank cap can be removed.
EWA10880
w
8 Do not overfill the fuel tank, otherwise it may overflow when the
fuel warms up and expands.
Avoid spilling fuel on the hot
engine.
8
9
To install the fuel tank cap
1. Insert the fuel tank cap into the tank
opening with the key inserted in the
lock and with the marks on the cap
and tank aligned.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
ECA10070
cC
Immediately wipe off spilled fuel with
a clean, dry, soft cloth, since fuel may
3-6
3D1-F8199-11ch3SGML.pmd
6
2006/08/17, 18:14
Catalytic converter<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
deteriorate painted surfaces or plastic parts.
EAU36080
Recommended fuel:
UNLEADED GASOLINE ONLY
Fuel tank capacity:
4.5 L (1.19 US gal) (0.98 Imp.gal)
ECA11400
cC
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content
does not exceed 10%. Gasohol containing methanol is not recommended by
Yamaha because it can cause damage
to the fuel system or vehicle performance problems.
EAU13431
Catalytic converter
This model is equipped with a catalytic
converter in the exhaust system.
EWA10860
The exhaust system is hot after operation. Make sure that the exhaust
system has cooled down before doing any maintenance work.
ECA10700
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts, such
as the valves and piston rings, as well
as to the exhaust system.
The following precautions must be
observed to prevent a fire hazard or
other damages.
8 Use only unleaded gasoline. The
use of leaded gasoline will cause
unrepairable damage to the catalytic converter.
8 Never park the vehicle near possible fire hazards such as grass
or other materials that easily
burn.
8 Do not allow the engine to idle
too long.
3-7
7
2
3
4
cC
Your Yamaha engine has been designed
to use regular unleaded gasoline with a
pump octane number [(R+M)/2] of 86 or
higher, or a research octane number of
91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand
or premium unleaded fuel. Use of unleaded fuel will extend spark plug life
and reduce maintenance costs.
3D1-F8199-11ch3SGML.pmd
1
w
2006/08/17, 18:14
5
6
7
8
9
Kickstarter<IXE>
Seat<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU13680
Kickstarter
EAUT1501
Seat
1
2
3
4
5
6
7
NOTE:
Make sure that the seat is properly secured before riding.
1
ZAUM00**
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left unattended.
ZAUM00**
1. Kickstarter
To start the engine, fold out the kickstarter
lever, move it down lightly with your foot
until the gears engage, and then push it
down smoothly but forcefully.
8
To open the seat
1. Place the scooter on the centerstand.
2. Insert the key into the main switch,
and then turn it counterclockwise
to the first “OPEN” position. If the
main switch is in the “LOCK” position, turn the key counterclockwise
to the second “OPEN” position.
NOTE:
Do not push inward when turning the key
from “OFF” to “OPEN” or from “LOCK”
to “OPEN”.
9
3. Fold the seat up.
3-8
3D1-F8199-11ch3SGML.pmd
8
2006/08/17, 18:14
Helmet holder<IXE>
Storage compartment (front)<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU14300
Helmet holder
To release the helmet from the helmet holder
Open the seat, remove the helmet from
the helmet holder, and then close the
seat.
EAU14400
Front storage compartment
1
1
2
1
3
ZAUM00**
4
ZAUM00**
1. Helmet holder
1. Front storage compartment
EWA11190
The helmet holder is located under the
seat.
w
8 Do not exceed the load limit of
1.5 kg (3 lb) for the front storage
compartment.
8 Do not exceed the maximum
load of 77 kg (170 lb) for the vehicle.
To secure a helmet to the helmet
holder
1. Open the seat. (See page 3-8.)
2. Attach the helmet to the helmet
holder, and then securely close the
seat.
w
Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of control and possibly an accident.
3-9
9
6
7
8
9
EWA10160
3D1-F8199-11ch3SGML.pmd
5
2006/08/17, 18:14
Storage compartment<IXE>
Carrier<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU14451
Storage compartment
washing the vehicle, be careful not to
let any water enter the storage compartment.
EAU15110
Carrier
1
1
1
2
3
4
5
6
ZAUM00**
ZAUM00**
1. Storage compartment
1. Rear carrier
The storage compartment is located
under the seat. (See page 3-8.)
w
EWA10170
8 Do not exceed the load limit of 3
kg (7 lb) for the carrier.
8 Do not exceed the maximum
load of 77 kg (170 lb) for the vehicle.
EWA10961
7
8
9
w
8 Do not exceed the load limit of 5
kg (11 lb) for the storage compartment.
8 Do not exceed the maximum
load of 77 kg (170 lb) for the vehicle.
When storing the owner’s manual or
other documents in the storage compartment, be sure to wrap them in a plastic
bag so that they will not get wet. When
3-10
3D1-F8199-11ch3SGML.pmd
10
2006/08/17, 18:14
Luggage hook<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAUT1070
Luggage hook
1
2
3
1
4
ZAUM00**
1. Luggage hook
5
EWAT1030
w
6
8 Do not exceed the load limit of 1
kg (2 lb) for the luggage hook.
8 Do not exceed the maximum
load of 77 kg (170 lb) for the vehicle.
7
8
9
3-11
3D1-F8199-11ch3SGML.pmd
11
2006/08/17, 18:14
EAU15580
PRE-OPERATION CHECKS
EAU15591
1
2
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss
of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspection, to check the following points before each ride.
NOTE:
Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very short
time; and the added safety it assures is more than worth the time involved.
3
EWA11150
4
w
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the vehicle.
5
6
7
8
9
4-1
3D1-F8199-71ch4SGML.pmd
1
2006/05/15, 19:24
Pre-operation check list<IXE>
PRE-OPERATION CHECKS
EAU15603
Pre-operation check list
ITEM
CHECKS
PAGE
Fuel
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
3-6
Engine oil
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
6-8
Final transmission oil
• Check vehicle for oil leakage.
6-10
Coolant
• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.
6-11
Front brake
•
•
•
•
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
6-15, 6-16
Rear brake
•
•
•
•
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
6-16
Throttle grip
• Make sure that operation is smooth.
• Check free play.
• If necessary, have Yamaha dealer make adjustment or lubricate.
6-13, 6-17
Wheels and tires
•
•
•
•
6-13, 6-15
Brake levers
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
2
2
3
4
5
6
7
Check for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.
8
6-17
4-2
3D1-F8199-71ch4SGML.pmd
1
2006/05/15, 19:24
9
PRE-OPERATION CHECKS
ITEM
CHECKS
• Make sure that operation is smooth.
• Lubricate pivot if necessary.
Centerstand
1
2
PAGE
6-18
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
Instruments, lights, signals
and switches
• Check operation.
• Correct if necessary.
3-3
Engine stop switch
• Check operation.
3-4
3
4
5
6
7
8
9
4-3
3D1-F8199-71ch4SGML.pmd
3
2006/05/15, 19:24
-
Starting a cold engine<IXE>
EAU15941
OPERATION AND IMPORTANT RIDING POINTS
EAU15980
EWA10870
w
EAUT1510
Starting a cold engine
ECA10250
8 Become thoroughly familiar with
all operating controls and their
functions before riding. Consult
a Yamaha dealer regarding any
control or function that you do
not thoroughly understand.
8 Never start the engine or operate
it in a closed area for any length
of time. Exhaust fumes are poisonous, and inhaling them can
cause loss of consciousness and
death within a short time. Always
make sure that there is adequate
ventilation.
8 For safety, always start the engine
with the centerstand down.
ECA11130
cC
cC
See page 5-3 for engine break-in instructions prior to operating the vehicle for the first time.
For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!
1. Turn the key to “ON” and make sure
that the engine stop switch is set
to “#”.
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the front
or rear brake.
NOTE:
If the engine does not start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to preserve the battery. Do not crank the engine more than 10 seconds on any one
attempt. If the engine does not start, try
with the throttle open 1/8 turn.
5-1
3D1-F8199-11ch5SGML.pmd
1
2006/05/15, 19:06
1
2
3
4
5
6
7
8
9
Starting off<IXE>
Acceleration and deceleration<IXE>
Braking<IXE>
OPERATION AND IMPORTANT RIDING POINTS
EAU16770
Starting off
1
2
3
EAU16780
Acceleration and deceleration
NOTE:
Before starting off, allow the engine to
warm up.
1. While pulling the rear brake lever
with your left hand and holding the
carrier with your right hand, push
the scooter off the centerstand.
4
(a)
(b)
EWA10300
(b)
w
(a)
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
(a). To reduce the speed, turn the throttle
grip in direction (b).
6
7
ZAUM00**
8
9
1.Close the throttle completely.
2.Apply both front and rear brakes simultaneously while gradually increasing the pressure.
ZAUM00**
5
EAU16791
Braking
2. Sit astride the seat, and then adjust the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signal off.
8 Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
8 Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole covers become extremely slippery
when wet. Therefore, slow down
when approaching such areas
and cross them with caution.
8 Keep in mind that braking on a
wet road is much more difficult.
8 Ride slowly down a hill, as braking downhill can be very difficult.
5-2
3D1-F8199-11ch5SGML.pmd
2
2006/05/15, 19:06
Engine break-in<IXE>
Parking<IXE>
OPERATION AND IMPORTANT RIDING POINTS
EAU16830
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances. During this period, prolonged full-throttle
operation or any condition that might
result in engine overheating must be
avoided.
EAU16950
0~150 km (0~90 mi)
Avoid prolonged operation above 1/3
throttle.
After every hour of operation, stop the
engine, and then let it cool for five to
ten minutes.
Vary the engine speed from time to time.
Do not operate the engine at one set
throttle position.
150~500 km (90~300 mi)
Avoid prolonged operation above 1/2
throttle.
Rev the engine freely through the gears,
but do not use full throttle at any time.
EAU17212
Parking
When parking, stop the engine, and then
remove the key from the main switch.
2
500~1000 km (300~600 mi)
Avoid prolonged operation above 3/4
throttle.
3
ECA10350
cC
4
After 1000 km (600 mi) of operation,
the engine oil must be changed and
the oil strainer cleaned.
5
6
1000 km (600 mi) and beyond
Avoid prolonged full-throttle operation.
Vary the speed occasionally.
7
ECA10270
cC
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
8
9
ZAUM00**
EWA10310
w
8 Since the engine and exhaust
system can become very hot,
5-3
3D1-F8199-11ch5SGML.pmd
3
1
2006/05/15, 19:06
OPERATION AND IMPORTANT RIDING POINTS
1
2
park in a place where pedestrians or children are not likely to
touch them.
8 Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.
ECA10380
3
cC
4
Never park in an area where there are
fire hazards such as grass or other
flammable materials.
5
6
7
8
9
5-4
3D1-F8199-11ch5SGML.pmd
4
2006/05/15, 19:06
Maintenance, periodic<IXE>
EAU17224
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17231
Safety is an obligation of the owner.
Periodic inspection, adjustment and lubrication will keep your vehicle in the
safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following
pages.
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual that
is certified (if applicable).
EWA10320
w
If you are not familiar with maintenance work, have a Yamaha dealer do
it for you.
EAU17301
PERIODIC MAINTENANCE
PROPER PERIODIC MAINTENANCE
OF YOUR VEHICLE IS IMPORTANT IN
ORDER TO ENJOY LONG, PLEASURABLE SERVICE. ESPECIALLY IMPORTANT ARE THE MAINTENANCE SERVICES RELATED TO EMISSIONS CONTROL. THESE CONTROLS NOT ONLY
FUNCTION TO ENSURE CLEANER
AIR, BUT ARE ALSO VITAL TO
PROPER ENGINE OPERATION AND
MAXIMUM PERFORMANCE. IN THE
FOLLOWING PERIODIC MAINTENANCE CHARTS, THE SERVICES
RELATED TO EMISSIONS CONTROL
ARE GROUPED SEPARATELY. THESE
SERVICES REQUIRE SPECIALIZED
DATA, KNOWLEDGE, AND EQUIPMENT. YAMAHA DEALERS ARE
TRAINED AND EQUIPPED TO PERFORM THESE PARTICULAR SERVICES.
6-1
3D1-F8199-11ch6SGML.pmd
1
2006/08/17, 18:15
1
2
3
4
5
6
7
8
9
Maintenance, emission control system<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17560
Periodic maintenance chart for the emission control system
INITIAL
1
NO.
ITEM
ROUTINE
2
3
4
1
*
2
9
4,000 mi
6,000 mi
8,000 mi
10,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
12
18
24
30
months
months
months
months
• Check fuel and vacuum hoses for
cracks or damage.
• Replace if necessary.
√
√
√
√
√
Spark plug
• Check condition.
• Adjust gap and clean.
• Replace at 4000 mi (7000 km) or
12 months and thereafter every
4000 mi (6000 km) or 12 months.
√
Replace.
√
Replace.
√
3
*
Valve clearance
• Check and adjust valve clearance
when engine is cold.
4
*
Crankcase breather
system
• Check breather hose for cracks or
damage.
• Replace if necessary.
5
*
Idle speed
• Check and adjust engine idle
speed.
6
*
Exhaust system
7
*
Air induction system
7
8
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
Fuel line
5
6
600 mi
(1,000 km)
or
1
month
√
Every 6000 mi (10000 km)
√
√
√
√
√
√
√
√
√
√
• Check for leakage.
• Tighten if necessary.
• Replace gasket(s) if necessary.
√
√
√
√
√
• Check the air cut-off valve, reed
valve, and hose for damage.
• Replace any damaged parts.
√
√
√
√
√
√
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
6-2
3D1-F8199-11ch6SGML.pmd
2
2006/08/17, 18:15
Maintenance and lubrication, periodic<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU32123
General maintenance and lubrication chart
INITIAL
NO.
ITEM
ROUTINE
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
• Check runout and for damage.
• Replace if necessary.
√
√
√
√
√
Tires
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
√
√
√
√
√
Wheel bearings
• Check bearings for smooth
operation.
• Replace if necessary.
√
√
√
√
√
√
√
√
Repack.
√
√
√
√
√
√
*
Front brake
• Check operation.
• Adjust cable and replace brake
shoes if necessary.
3
*
Rear brake
• Check operation.
• Adjust cable and replace brake
shoes if necessary.
4
*
Wheels
*
2
5
6
*
4,000 mi
6,000 mi
8,000 mi
10,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
12
18
24
30
months
months
months
months
√
• Replace.
*
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
√
Air filter element
1
600 mi
(1,000 km)
or
1
month
7
*
Steering bearings
• Check bearing assemblies for
looseness.
• Moderately repack with lithiumsoap-based grease every 8000 mi
(13000 km) or 24 months.
8
*
Chassis fasteners
• Check all chassis fitting and
fasteners.
• Correct if necessary.
3
2
3
4
5
6
7
√
6-3
3D1-F8199-11ch6SGML.pmd
1
2006/08/17, 18:15
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
INITIAL
NO.
ITEM
ROUTINE
1
2
9
Front and rear brake • Apply lithium-soap-based grease
lever pivot
(all-purpose grease) lightly.
10
Centerstand
3
600 mi
(1,000 km)
or
1
month
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
4,000 mi
6,000 mi
8,000 mi
10,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
12
18
24
30
months
months
months
months
√
√
√
√
√
• Check operation.
• Lubricate.
√
√
√
√
√
11
*
Front fork
• Check operation and for oil
leakage.
• Replace if necessary.
√
√
√
√
√
12
*
Shock absorber
assembly
• Check operation and for oil
leakage.
• Replace if necessary.
√
√
√
√
√
6
13
Engine oil
• Change (warm engine before
draining).
• Check oil level and vehicle for oil
leakage.
√
√
√
√
√
√
7
14
Engine oil strainer
• Clean.
√
Cooling system
• Check coolant level and vehicle for
coolant leakage.
4
5
15
8
*
√
• Change.
Final transmission
oil
• Check vehicle for oil leakage.
• Change.
*
V-belt
• Replace.
18
*
Front and rear brake
• Check operation.
switches
19
*
Control and meter
cables
16
9
√
17
• Apply Yamaha chain and cable
lube or engine oil 10W-30
thoroughly.
√
4
√
√
√
Every 3 years
√
√
√
Every 6250 mi (10000 km)
√
√
√
√
√
√
√
√
√
√
√
√
6-4
3D1-F8199-11ch6SGML.pmd
√
2006/08/17, 18:15
PERIODIC MAINTENANCE AND MINOR REPAIR
INITIAL
NO.
20
21
ITEM
ROUTINE
*
• Check operation and free play.
• Adjust the throttle cable free play if
Throttle grip housing
necessary.
and cable
• Lubricate the throttle grip housing
and cable.
*
Lights, signals and
switches
• Check operation.
• Adjust headlight beam.
600 mi
(1,000 km)
or
1
month
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
4,000 mi
6,000 mi
8,000 mi
10,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
12
18
24
30
months
months
months
months
1
2
√
√
√
√
√
3
√
√
√
√
√
√
4
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NOTE:
From 12000 mi ( 19000 km) or 36 months, repeat the maintenance intervals starting from 4000 mi (7000 km) or 12 months.
5
6
7
8
9
6-5
3D1-F8199-11ch6SGML.pmd
5
2006/08/17, 18:15
Panel, removing and installing<IXE>
Spark plug, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU18751
EAUT1482
Removing and installing the
panel
Checking the spark plug
1
1
1
2
3
ZAUM00**
1
1. Panel A
4
ZAUM00**
To install the panel
Place the panel in the original position,
and then install the screw.
ZAUM00**
5
1. Panel A
6
7
8
The panel shown needs to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time the panel needs
to be removed and installed.
EAU19272
9
Panel A
To remove the panel
Remove the screw, and then pull outward on the areas shown.
1. Partition
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked in
accordance with the periodic maintenance and lubrication chart. In addition,
the condition of the spark plug can reveal the condition of the engine.
To remove the spark plug
1. Remove panel A. (See page 6-6.)
2. Remove the partition between the
battery and the spark plug by pulling it up.
6-6
3D1-F8199-11ch6SGML.pmd
6
2006/08/17, 18:15
PERIODIC MAINTENANCE AND MINOR REPAIR
3. Remove the spark plug cap.
4. Remove the spark plug as shown,
with a spark plug wrench available
at a Yamaha dealer.
To check the spark plug
1. Check that the porcelain insulator
around the center electrode of the
spark plug is a medium-to-light tan
(the ideal color when the vehicle is
ridden normally).
NOTE:
If the spark plug shows a distinctly different color, the engine could be defective. Do not attempt to diagnose such
problems yourself. Instead, have a
Yamaha dealer check the vehicle.
2. Check the spark plug for electrode
erosion and excessive carbon or
other deposits, and replace it if necessary.
Specified spark plug:
CR7E (NGK)
wire thickness gauge and, if necessary, adjust the gap to specification.
Tightening torque:
Spark plug:
13 Nm (1.3 m • kgf, 9.4ft • lbf)
1
NOTE:
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4~1/2 turn past
finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.
1
4. Install the spark plug cap.
5. Install the partition and the panel.
1. Spark plug wrench
4
5
6
Spark plug gap:
0.7 ~ 0.8 mm (0.028 ~ 0.031 in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark
plug wrench, and then tighten it to
the specified torque.
6-7
7
3
ZAUM00**
To install the spark plug
1. Measure the spark plug gap with a
3D1-F8199-11ch6SGML.pmd
2
2006/08/17, 18:15
7
8
9
Engine oil<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1460
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
Engine oil and oil strainer
1
2
3
4
5
6
7
The engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil strainer cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the engine oil level
1.Place the vehicle on the centerstand.
NOTE:
Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.
2. Start the engine, warm it up for several minutes, and then turn it off.
8
1
2
3
ZAUM00**
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for several minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (without
screwing it in), and then remove it
again to check the oil level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.
9
4. If the engine oil is below the minimum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
1
ZAUM00**
1. Engine oil drain bolt A
3. Remove the engine oil filler cap and
the engine oil drain bolts A and B
to drain the oil from the crankcase.
6-8
3D1-F8199-11ch6SGML.pmd
8
2006/08/17, 18:15
PERIODIC MAINTENANCE AND MINOR REPAIR
4
3
2
1
1
NOTE:
Make sure that the O-ring is properly
seated.
7. Install engine oil drain bolt A, and
then tighten both drain bolts to their
specified torques.
8. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.
Recommended engine oil:
See page 8-1.
Oil change quantity:
0.78 L (0.82 US qt) (0.69 Imp.qt)
ZAUM00**
1.
2.
3.
4.
Tightening torque:
Engine oil drain bolt A:
23 Nm (2.3 m • kgf, 16.6 ft • lbf)
Engine oil drain bolt B:
32 Nm (3.2 m • kgf, 23.1 ft • lbt)
Engine oil drain bolt B
O-ring
Compression spring
Strainer
ECAT1020
cC
When removing the engine oil drain
bolt B, the O-ring, compression
spring, and oil strainer will fall out.
Take care not to lose these parts.
4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, compression
spring, O-ring and engine oil drain
bolt B.
1
ZAUM00**
1. Oil filler hole
ECA11670
9
2
3
cC
8 Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
8 Be sure no foreign material enters the crankcase.
4
9. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check
the oil level and correct it if necessary.
8
6-9
3D1-F8199-11ch6SGML.pmd
1
2006/08/17, 18:15
5
6
7
9
Final transmission oil<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1560
Final transmission oil
1
2
3
4
5
6
7
The final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several minutes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
2
Tightening torque:
Final transmission oil filler bolt:
23Nm (2.3m • kgf, 16.6 ft • lbf)
1
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.1 L (0.11 US qt) (0.08 Imp.qt)
ZAUM00**
1. Final transmission oil filler bolt
2. Final transmission oil drain bolt
EWA11310
w
4. Remove the oil filler bolt and drain
bolt to drain the oil from the final
transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to the
specified torque.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
Tightening torque:
Final transmission oil drain bolt:
13 Nm (1.3 m • kgf, 9.4 ft • lbf)
8
8 Make sure that no foreign material enters the final transmission
case.
8 Make sure that no oil gets on the
tire or wheel.
9
6. Add the specified amount of the
recommended final transmission
oil, and then install the oil filler bolt
and tighten it to the specified
torque..
6-10
3D1-F8199-11ch6SGML.pmd
10
2006/08/17, 18:15
Coolant<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coolant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
NOTE:
The coolant should be between the minimum and maximum level marks.
EAUT1521
To check the coolant level
The coolant level should be checked as
follows before each ride. In addition, the
coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart.
1. Place the vehicle on the
centerstand.
NOTE:
8 The coolant level must be checked
on a cold engine since the level
varies with engine temperature.
8 Make sure that the vehicle is positioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
2. Check the coolant level in the coolant reservoir.
3. If the coolant is at or below the minimum level mark, remove panel A
and the reservoir cap. (See page 66.)
4. Add coolant or distilled water to
raise the coolant to the maximum
level mark, and install the coolant
reservoir cap and the panel.
1
2
Coolant reservoir capacity (up to the
maximum level mark):
0.25 L (0.26 US qt) (0.22 Imp.qt)
ECA10470
cC
ZAUM00**
1. Maximum level mark
2. Minimum level mark
1
ZAUM00**
8 If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
8 If water has been used instead
of coolant, replace it with coolant as soon as possible, otherwise the engine may not be sufficiently cooled and the cooling
system will not be protected
against frost and corrosion.
8 If water has been added to the
coolant, have a Yamaha dealer
6-11
11
2
3
1. Coolant reservoir cap
3D1-F8199-11ch6SGML.pmd
1
2006/08/17, 18:15
4
5
6
7
8
9
Air filter element and check hose, replacing and cleaning<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
1
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of the
coolant will be reduced.
EAUT1490
Replacing the air filter element
and cleaning the check hose
ECA10480
cC
2
8 Make sure that the air filter element is properly seated in the air
filter case.
8 The engine should never be operated without the air filter element installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
EWA10380
2
w
3
Never attempt to remove the radiator
cap when the engine is hot.
4
5
NOTE:
If the engine overheats, see page 6-25
for further instructions.
EAU33030
6
Changing the coolant
7
w
2. Pull the air filter element out.
3. Insert a new air filter element into
the air filter case as shown.
1
3
ZAUM00**
1. Air filter case cover
2. Air filter element
3. Air filter check hose
4. Install the air filter case cover by
installing the screws.
EWA10380
8
9
Never attempt to remove the radiator
cap when the engine is hot.
The coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart. Have a
Yamaha dealer change the coolant.
The air filter element should be replaced
at the intervals specified in the periodic
maintenance and lubrication chart. Replace the air filter element more frequently if you are riding in unusually wet
or dusty areas. In addition, the air filter
check hose must be frequently checked
and cleaned if necessary.
To clean the air filter check hose
1. Check the hose on the side of the
air filter case for accumulated dirt
or water.
2. If dirt or water is visible, remove
the hose, clean it, and then install
it.
To replace the air filter element
1. Remove the air filter case cover by
removing the screws.
6-12
3D1-F8199-11ch6SGML.pmd
12
2006/08/17, 18:15
Carburetor<IXE>
Throttle cable free play, checking<IXE>
Tires<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU21251
Carburetor
The carburetor is an important part of
the engine and its emission control system, which requires very sophisticated
adjustment. Therefore, carburetor adjustments should be left to Yamaha dealer,
who has the necessary professional
knowledge and experience.
EAU21381
Checking the throttle cable
free play
The throttle cable free play should measure 1.5~3.5 mm (0.06~0.14 in) at the
throttle grip. Periodically check the
throttle cable free play and, if necessary,
have a Yamaha dealer adjust it.
EAU21911
Tires
To maximize the performance, durability, and safe operation of your scooter,
note the following points regarding the
specified tires.
1
2
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
EWA10540
3
4
w
6-13
3D1-F8199-11ch6SGML.pmd
13
Because loading has an enormous
impact on the handling, braking, performance and safety characteristics
of your scooter, you should keep the
following precautions in mind.
8 NEVER
OVERLOAD THE
SCOOTER! Operation of an overloaded scooter may result in tire
damage, loss of control, or severe injury. Make sure that the
total weight of rider, cargo, and
accessories does not exceed the
specified maximum load for the
vehicle.
8 Improper tire air pressure greatly
affects tire life and handling.
If the tire air pressure is too high,
2006/08/17, 18:15
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
shocks from the road will not be
dampened but instead be transmitted to the frame and handlebars, which impairs riding comfort. In addition, the scooter will
be unstable in curves.
If the tire air pressure is too low,
the tires will be damaged and the
tire life shortened. In addition, the
tires could slip off the wheel rims
during braking, which could result in tube damage. The scooter
could also easily turn over in a
curve.
Tire air pressure* (measured on cold
tires):
Front:
150 kPa (22 psi) (1.50 kgf/cm2)
Rear:
175 kPa (25 psi) (1.75 kgf/cm2)
Tire inspection
Always check the tires before operating
the scooter. If a tire tread shows crosswise lines (minimum tread depth), if the
tire has a nail or glass fragments in it,
or if the sidewall is cracked, contact a
Yamaha dealer immediately and have the
tire replaced.
3D1-F8199-11ch6SGML.pmd
14
Minimum tire tread depth (front and
rear):
1.0 mm (0.04 in)
Tire information
This scooter is equipped with panel
wheels and tubeless tires.
Front tire:
Size:
90/90-10 41J
Manufacturer/model:
CHENG SHIN/C-922
Rear tire:
Size:
90/90-10 41J
Manufacturer/model:
CHENG SHIN/C-922
EWA10580
w
8 It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace the
tire immediately.
8 The replacement of all wheel- and
brake-related parts, including the
tires, should be left to a Yamaha
dealer, who has the necessary
professional knowledge and experience.
6-14
2006/08/17, 18:15
Wheels<IXE>
Brake lever free play, adjusting<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU21960
Cast wheels
To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified wheels.
8 The wheel rims should be checked
for cracks, bends or warpage before each ride. If any damage is
found, have a Yamaha dealer replace the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked wheel
must be replaced.
8 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in poor
performance, adverse handling
characteristics, and a shortened
tire life.
8 Ride at moderate speeds after
changing a tire since the tire surface must first be “broken in” for it
to develop its optimal characteristics.
EAU22130
Adjusting the brake lever free
play
1
1
ZAUM00**
15
(a)
1
3
1. Adjusting nut
4
EWA10650
w
ZAUM00**
1. Front brake lever free play
The brake lever free play should measure 10~20 mm (0.4~0.8 in) as shown.
Periodically check the brake lever free
play and, if necessary, adjust it as follows.
To increase the brake lever free play,
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, turn the adjusting
nut in direction (b).
If proper adjustment cannot be obtained as described, have a Yamaha
dealer make this adjustment.
6-15
3D1-F8199-11ch6SGML.pmd
2
(b)
2006/08/17, 18:15
5
6
7
8
9
Rear brake lever free play, adjusting<IXE>
Brake shoes, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22170
EAU22361
Adjusting the rear brake lever
free play
Checking the front and rear
brake shoes
Front
1
(b) 1
1
2
3
1
2
(a)
ZAUM00**
1. Adjusting nut
4
EWA10650
w
ZAUM00**
If proper adjustment cannot be obtained as described, have a Yamaha
dealer make this adjustment.
5
1. Rear brake lever free play
6
7
8
9
The brake lever free play should measure 10~20 mm (0.039~0.79 in) as
shown. Periodically check the brake lever free play and, if necessary, adjust it
as follows.
To increase the brake lever free play,
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, turn the adjusting
nut in direction (b).
ZAUM00**
1. Wear indicator
2. Wear limit line
Rear
1
2
ZAUM00**
6-16
3D1-F8199-11ch6SGML.pmd
16
1. Wear indicator
2. Wear limit line
2006/08/17, 18:15
Throttle grip and cable, checking and lubricating<IXE>
Brake levers, lubricating<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
The front and rear brake shoes must be
checked for wear at the intervals specified in the periodic maintenance and lubrication chart. Each brake is provided
with a wear indicator, which allows you
to check the brake shoe wear without
having to disassemble the brake. To
check the brake shoe wear, check the
position of the wear indicator while applying the brake. If a brake shoe has
worn to the point that the wear indicator
reaches the wear limit line, have a
Yamaha dealer replace the brake shoes
as a set.
EAU23111
EAU23170
Checking and lubricating the
throttle grip and cable
Lubricating the front and rear
brake levers
The operation of the throttle grip should
be checked before each ride. In addition, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease (allpurpose grease)
1
2
3
4
5
6
7
8
9
6-17
3D1-F8199-11ch6SGML.pmd
17
2006/08/17, 18:15
Centerstand, checking and lubricating<IXE>
Front fork, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23191
Checking and lubricating the
centerstand
1
2
The operation of the centerstand should
be checked before each ride, and the
pivots and metal-to-metal contact surfaces should be lubricated if necessary.
EWA11300
3
4
w
EAU23271
Checking the front fork
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic maintenance and lubrication chart.
To check the condition
EWA10750
If the centerstand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.
w
ZAUM00**
Securely support the motorcycle so
that there is no danger of it falling
over.
5
6
Recommended lubricant:
Lithium-soap-based grease (allpurpose grease)
7
8
9
Check the inner tubes for scratches,
damage and excessive oil leakage.
ECA10590
cC
If any damage is found or the front
fork does not operate smoothly, have
a Yamaha dealer check or repair it.
To check the operation
1. Place the motorcycle on a level surface and hold it in an upright position.
2. While applying the front brake, push
down hard on the handlebars several times to check if the front fork
compresses and rebounds
smoothly.
6-18
3D1-F8199-11ch6SGML.pmd
18
2006/08/17, 18:15
Steering, checking<IXE>
Wheel bearings, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23280
EAU23290
Checking the steering
Checking the wheel bearings
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine to
raise the front wheel off the ground.
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication
chart. If there is play in the wheel hub or
if the wheel does not turn smoothly,
have a Yamaha dealer check the wheel
bearings.
ZAUM00**
1
2
3
EWA10750
w
4
Securely support the motorcycle so
that there is no danger of it falling
over.
5
6
2. Hold the lower ends of the front fork
legs and try to move them forward
and backward. If any free play can
be felt, have a Yamaha dealer check
or repair the steering.
7
8
9
6-19
3D1-F8199-11ch6SGML.pmd
19
2006/08/17, 18:15
Battery<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1230
Battery
1
2
3
4
5
6
7
1
ZAUM00**
1. Battery
This model is equipped with a sealedtype (MF) battery, which does not require any maintenance. There is no need
to check the electrolyte or to add distilled water.
ECA10620
8
cC
9
Never attempt to remove the battery
cell seals, as this would permanently
damage the battery.
EWA10760
w
8 Electrolyte is poisonous and dangerous since it contains sulfuric
acid, which causes severe burns.
Avoid any contact with skin, eyes
or clothing and always shield
your eyes when working near
batteries. In case of contact, administer the following FIRST AID.
9 EXTERNAL: Flush with
plenty of water.
9 INTERNAL: Drink large
quantities of water or milk
and immediately call a
physician.
9 EYES: Flush with water for
15 minutes and seek prompt
medical attention.
8 Batteries produce explosive hydrogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and provide sufficient ventilation when
charging it in an enclosed space.
8 KEEP THIS AND ALL BATTERIES
OUT OF THE REACH OF CHILDREN.
The battery is located under the
footboard. Remove panel A to access
the battery. (See page 6-6.)
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
2. If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.
3. Fully charge the battery before installation.
4. After installation, make sure that
the battery leads are properly connected to the battery terminals.
ECA10630
cC
8 Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
8 To charge a sealed-type (MF) bat-
6-20
3D1-F8199-11ch6SGML.pmd
20
2006/08/17, 18:15
Fuse, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
tery, a special (constant-voltage)
battery charger is required. Using a conventional battery
charger will damage the battery.
If you do not have access to a
sealed-type (MF) battery charger,
have a Yamaha dealer charge
your battery.
EAUT1240
Replacing the fuse
ECA10640
cC
Do not use a fuse of a higher amperage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows again,
have a Yamaha dealer check the
electrical system.
1
ZAUM00**
1. Fuse
The fuse holder is located beside the
battery. Remove panel A to access the
fuse. (See page 6-6.)
If the fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
Specified fuse:
7.5 A
6-21
3D1-F8199-11ch6SGML.pmd
21
2006/08/17, 18:15
1
2
3
4
5
6
7
8
9
Headlight bulb, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23780
Replacing the headlight bulb
1
2
2
This model is equipped with a quartz
bulb headlight. If the headlight bulb burns
out, replace it as follows.
1. Remove the headlight unit by removing the screws.
1
3
1
1
ZAUM00**
ZAUM00**
1. Headlight coupler
2. Bulb cover
4
1. Headlight bulb holder
EWA10790
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
5
6
ZAUM00**
7
8
1. Headlight unit
2. Disconnect the headlight coupler,
and then remove the bulb cover.
w
Headlight bulbs get very hot. Therefore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.
4. Place a new headlight bulb into position, and then secure it with the
bulb holder.
9
ECA10660
cC
6-22
3D1-F8199-11ch6SGML.pmd
22
Do not touch the glass part of the
headlight bulb to keep it free from oil,
otherwise the transparency of the
glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
2006/08/17, 18:15
Tail/brake light bulb, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol
or thinner.
5. Install the headlight bulb cover, and
then connect the coupler.
6. Install the headlight unit by installing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb
wise the lens may break.
1. Remove the tail/brake light lens by
removing the screws.
1
2
2
3
1
4
5
ZAUM00**
6
1. Tail/brake light lens
2. Bulb
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screws.
ECA10680
cC
Do not overtighten the screws, other6-23
3D1-F8199-11ch6SGML.pmd
23
2006/08/17, 18:15
7
8
9
Troubleshooting<IXE>
Turn signal light bulb, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24202
EAU25880
Replacing a turn signal light
bulb
1
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur during operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
1. Remove the turn signal light lens
by removing the screw.
2
1
1
3
1. Turn signal light lens
2. Bulb
4
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screw.
5
ZAUM00**
6
2
ZAUM00**
2
1. Turn signal light lens
2. Bulb
7
8
ECA11190
cC
9
Do not overtighten the screw, otherwise the lens may break.
The following troubleshooting charts represent quick and easy procedures for
checking these vital systems yourself.
However, should your scooter require any
repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary
tools, experience, and know-how to service the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often inferior, have a shorter service life and can
lead to expensive repair bills.
6-24
3D1-F8199-11ch6SGML.pmd
24
2006/08/17, 18:15
Troubleshooting charts<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1580
Troubleshooting charts
Starting problems or poor engine performance
EWA10840
w
Keep away open flames and do not smoke while checking or working on the fuel system.
1. Fuel
1
2
3
There is enough fuel.
Check the compression.
There is no fuel.
Supply fuel.
Check the fuel level in
the fuel tank.
The engine does not start.
Check the compression.
4
5
2. Compression
There is compression.
Check the ignition.
There is no compression.
Have a Yamaha dealer
check the vehicle.
6
Operate the electric starter.
7
3. Ignition
Wet
Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.
Open the throttle halfway and operate
the electric starter.
8
Dry
Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the battery.
9
Remove the spark plug
and check the electrodes.
4. Battery
The engine turns over
quickly.
The battery is good.
The engine turns over
slowly.
Check the battery lead connections,
and charge the battery if necessary.
Operate the electric starter.
6-25
3D1-F8199-11ch6SGML.pmd
25
2006/08/17, 18:15
The engine does not start.
Have a Yamaha dealer
check the vehicle.
PERIODIC MAINTENANCE AND MINOR REPAIR
Engine overheating
EWAT1040
w
1
2
8 Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
8 Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the
detent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
3
4
The coolant level is low.
Check the cooling system
for leakage.
5
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
6
The coolant level
is OK.
There is
leakage.
There is
no leakage.
Have a Yamaha dealer check
and repair the cooling system.
Add coolant. (See NOTE.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
7
8
NOTE:
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
9
6-26
3D1-F8199-11ch6SGML.pmd
26
2006/08/17, 18:15
Care<IXE>
EAU25991
SCOOTER CARE AND STORAGE
EAU26090
Care
ECA10780
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed on
a car, however, it detracts from the overall appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a plastic bag after the engine has cooled
down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the spark
plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such products onto seals, gaskets and wheel
axles. Always rinse the dirt and
degreaser off with water.
3D1-F8199-71ch7SGML.pmd
Cleaning
1
cC
8 Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are used
on hard-to-remove dirt, do not
leave the cleaner on the affected
area any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry it,
and then apply a corrosion protection spray.
8 Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to clean
plastic.
8 Do not use any harsh chemical
products on plastic parts. Be sure
to avoid using cloths or sponges
which have been in contact with
strong or abrasive cleaning products, solvent or thinner, fuel
(gasoline), rust removers or inhibitors, brake fluid, antifreeze or
electrolyte.
8 Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instruments, switches and lights),
breather hoses and vents.
8 For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as they
will cause dulling or scratching.
Some cleaning compounds for
plastic may leave scratches on
the windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing compound after washing.
1
2
3
4
5
6
7
8
9
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
7-1
2006/05/15, 19:27
SCOOTER CARE AND STORAGE
1
2
3
4
5
6
7
8
9
Use a toothbrush or bottlebrush for hardto-reach areas. Stubborn dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corrosive in combination with water, carry out
the following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
NOTE:
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the engine has cooled down.
ECA10790
cC
Do not use warm water since it increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainlesssteel parts, including the exhaust
system. (Even the thermally induced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal cleaner
to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA10940
w
8 Make sure that there is no oil or
wax on the brakes or tires. If necessary, clean the brake discs and
brake linings with a regular brake
disc cleaner or acetone, and
wash the tires with warm water
and a mild detergent.
8 Before operating the scooter test
its braking performance and cornering behavior.
ECA10800
cC
8 Apply spray oil and wax sparingly and make sure to wipe off
any excess.
8 Never apply oil or wax to any rubber and plastic parts, but treat
them with a suitable care product.
8 Avoid using abrasive polishing
compounds as they will wear
away the paint.
7-2
3D1-F8199-71ch7SGML.pmd
2
2006/05/15, 19:27
Storage<IXE>
SCOOTER CARE AND STORAGE
NOTE:
Consult a Yamaha dealer for advice on
what products to use.
EAU26300
Storage
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it against
dust with a porous cover.
ECA10820
cC
8 Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
8 To prevent corrosion, avoid
damp cellars, stables (because of
the presence of ammonia) and
areas where strong chemicals are
stored.
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent the
fuel tank from rusting and the fuel
from deteriorating.
4. Perform the following steps to protect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
EWA10950
w
To prevent damage or injury from
sparking, make sure to ground the
7-3
3D1-F8199-71ch7SGML.pmd
3
2006/05/15, 19:27
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
spark plug electrodes while turning
the engine over.
1
2
3
4
5
6
7
8
9
NOTE:
Make any necessary repairs before storing the scooter.
5. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
7. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
8. Remove the battery and fully charge
it. Store it in a cool, dry place and
charge it once a month. Do not store
the battery in an excessively cold
or warm place [less than 0°C (30
°F) or more than 30°C (90°F)]. For
more information on storing the
battery, see page 6-20.
7-4
3D1-F8199-71ch7SGML.pmd
4
2006/05/15, 19:27
Specifications<IXE>
SPECIFICATIONS
EAU2633H
Dimensions
Engine oil
Carburetor
Type
YAMALUBE 4, SAE10W30 or SAE20W40
Overall length
1665 mm (65.6 in)
Overall width
630 mm (24.8 in)
Overall height
1005 mm (39.6 in)
Seat heigh
715 mm (28.1 in)
Wheelbase
1160 mm (45.7 in)
Ground clearance
85 mm (3.35 in)
Minimum turning radius
1800 mm (70.9 in)
0
10
30
50
70
90
110 130 ˚F
Spark plug (s)
YAMALUBE 4 (10W-30)
or SAE 10W-30
Manufacturer/model
NGK/CR7E
Spark plug gap
0.7-0.8 mm (0.028-0.031 in)
YAMALUBE 4 (20W-40)
or SAE 20W-40
-20
-10
0
10
20
30
Clutch
40 50 ˚C
Recommended engine oil grade
API service SG type or higher, JASO standard MA
Periodic oil change
0.78 L (0.82 US qt) (0.69 Imp.qt)
Weight
With oil and fuel
81.0 kg (179 lb)
Final transmission oil
Engine
Engine type
Liquid cooled 4-stroke, SOHC
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.0 cm3
Bore x stroke
38.0 x 43.5 mm (1.50 x 1.71 in)
Compression ratio
12.00 :1
Starting system
Electric starter and kickstarter
Lubrication system
Wet sump
Manufacturer
KEIHIN
Type x quantity
NCV18 x 1
Type
SAE10W30 type SE motor oil
Quantity
0.10 L (0.11 US qt) (0.09 Imp.qt)
Cooling system
Coolant reservoir capacity (up to the maximum level mark)
0.25 L (0.26 US qt) (0.22 Imp.qt)
Radiator capacity (including all routes)
0.50 L (0.53 US qt) (0.44 Imp.qt)
Air filter
Air filter element
Oil-coated paper element
Fuel
Recommended fuel
Unleaded gasoline only
Fuel tank capacity
4.5 L (1.19 US gal) (0.99 Imp.gal)
Clutch type
Dry, centrifugal automatic
Transmission
Primary reduction system
Helical gear
Primary reduction ratio
48/13 (3.692)
Secondary reduction system
Spur gear
Secondary reduction ratio
43/12 (3.583)
Transmission type
V-belt automatic
Operation
Centrifugal automatic type
1
2
3
4
5
6
7
8
Chassis
Frame type
Steel tube underbone
Caster angle
24.00 degree
Trail
70.0 mm (2.76 in)
8-1
3D1-F8199-71ch8SGML.pmd
1
2006/05/29, 11:53
9
SPECIFICATIONS
Front tire
1
2
3
4
Front brake
Type
Tubeless
Size
90/90-10 41J
Manufacturer/model
CHENG SHIN / C-922
Rear brake
Type
Drum brake
Operation
Left hand operation
Rear tire
Type
Tubeless
Size
90/90-10 41J
Manufacturer/model
CHENG SHIN / C-922
Front suspension
Type
Telescopic fork
Spring/shock absorber type
Coil spring
Wheel travel
59.0 mm (2.32 in)
Loading
5
Maximum load
77 kg (170 lb)
Tire air pressure (measured on cold tires)
6
7
8
9
Headlight
Type
Drum brake
Operation
Right hand operation
Loading condition
0-158 kg (0-348 lb)
Front
150 kPa (22 psi) (1.50 kgf/cm2) (1.50 bar)
Rear
175 kPa (25 psi) (1.75 kgf/cm2) (1.75 bar)
Front wheel
Rear suspension
Type
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
54.0 mm (2.13 in)
Electrical system
Wheel type
Cast wheel
Rim size
10 x 2.15
Bulb type
Halogen bulb
Bulb voltage, wattage x quantity
Headlight
12 V, 35 W/35.0 W x 1
Tail/brake light
12 V, 5.0 W/21.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
License plate light
12 V, 5.0 W x 1
Meter lighting
12 V, 1.7 W x 2
High beam indicator light
12 V, 1.7 W x 1
Turn signal indicator light
12 V, 1.7 W x 2
Coolant temperature warning light
14 V, 3.0 W x 1
Fuse
Fuse
7.5 A
Ignition system
CDI
Charging system
AC magneto
Rear wheel
Battery
Wheel type
Cast wheel
Rim size
10 x 2.15
Model
GTX5L-BS
Voltage, capacity
12 V, 4.0 Ah
8-2
3D1-F8199-71ch8SGML.pmd
2
2006/05/23, 15:45
Identification numbers<IXE>
Key identification number<IXE>
Vehicle identification number<IXE>
EAU26341
CONSUMER INFORMATION
EAU26351
Identification numbers
EAU26390
Key identification number
EAU26410
Vehicle identification number
Record the key identification number,
vehicle identification number and model
label information in the spaces provided
below for assistance when ordering
spare parts from a Yamaha dealer or for
reference in case the vehicle is stolen.
1
1
2
3
KEY IDENTIFICATION NUMBER:
ZAUM00**
1. Key identification number
VEHICLE IDENTIFICATION NUMBER:
The key identification number is
stamped into the key.
Record this number in the space provided and use it for reference when ordering a new key.
MODEL LABEL INFORMATION:
1. Vehicle identification number
The vehicle identification number is
stamped into the frame.
NOTE:
The vehicle identification number is used
to identify your motorcycle and may be
used to register your motorcycle with
the licensing authority in your area.
4
5
6
7
8
9
9-1
3D1-F8199-11ch9SGML.pmd
1
2006/08/17, 11:29
Model label<IXE>
CONSUMER INFORMATION
EAU26460
Model label
1
1
2
3
4
5
6
7
ZAUM00**
1. Model label
The model label is affixed to the location shown. Record the information on
this label in the space provided. This
information will be needed when ordering spare parts from a Yamaha dealer.
8
9
9-2
3D1-F8199-11ch9SGML.pmd
2
2006/08/17, 11:29
Safety defects, reporting<IXE>
CONSUMER INFORMATION
EAU26551
Reporting safety defects
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a
group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual
problems between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://
www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain
other information about motor vehicle safety from http://www.safercar.gov.
1
2
3
4
5
6
7
8
9
9-3
3D1-F8199-11ch9SGML.pmd
3
2006/08/17, 11:29
Noise regulation<IXE>
CONSUMER INFORMATION
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
1
2
3
4
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new
vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use
of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.
5
6
Exhaust system
Muffler
Exhaust pipe
Silencer
Intake system
Air cleaner case
Air cleaner element
Intake duct
7
8
9
9-4
3D1-F8199-11ch9SGML.pmd
4
2006/08/17, 11:29
Maintenance record<IXE>
CONSUMER INFORMATION
EAU26600
Maintenance record
Copies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to document that
maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder
that maintenance work is required. It is not acceptable proof of maintenance work.
Maintenance
interval
600 mi
(1000 km) or
1 month
Date of
service
Servicing dealer
name and address
Mileage
Remarks
1
2
3
2000 mi
(4000 km) or
6 months
4
4000 mi
(7000 km) or
12 months
5
6000 mi
(10000 km) or
18 months
6
8000 mi
(13000 km) or
24 months
7
10000 mi
(16000 km) or
30 months
8
12000 mi
(19000 km) or
36 months
9
14000 mi
(22000 km) or
42 months
9-5
3D1-F8199-11ch9SGML.pmd
5
2006/08/17, 11:29
CONSUMER INFORMATION
1
Maintenance
interval
16000 mi
(25000 km) or
48 months
2
18000 mi
(28000 km) or
54 months
3
20000 mi
(31000 km) or
60 months
Date of
service
Servicing dealer
name and address
Mileage
4
5
6
7
8
9
9-6
3D1-F8199-11ch9SGML.pmd
6
2006/08/17, 11:29
Remarks
Warranty, limited<IXE>
CONSUMER INFORMATION
EAU26681
YAMAHA MOTOR CORPORATION, U.S.A.
RIVA LIMITED WARRANTY
1
2
3
4
5
6
7
8
9
9-7
3D1-F8199-11ch9SGML.pmd
7
2006/08/17, 11:29
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-8
3D1-F8199-11ch9SGML.pmd
8
2006/08/17, 11:29
Warranty, extended<IXE>
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty
expires with genuine Yamaha Extended Service (Y.E.S.).
In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable
expenses you incur because your Yamaha needs
covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are
away from home. This superb coverage goes into effect
when you purchase Y.E.S., so it applies to any warranty
repairs as well as covered repairs during your entire
Y.E.S. plan period.
Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factory-backed coverage for extra
peace of mind.
Y.E.S. is flexible. You choose the plan that’s right for
you: 12 months, 24 months, 36 months or, on certain
models, even 48 months beyond your warranty period.
Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it
shows in the comprehensive coverage benefits. There
are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the
warranty. See the sample contract at your Yamaha
dealer to see how comforting uninterrupted factorybacked protection can be.
9
3
4
5
Y.E.S. coverage is transferable to a new owner if you
sell or trade-in. That can make your Yamaha much more
valuable!
6
7
8
9
9-9
3D1-F8199-11ch9SGML.pmd
2
Y.E.S. coverage is honored at any authorized Yamaha
dealer nationwide.
This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still
within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
you how easy it is to protect your investment with Yamaha
Extended Service.
You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses
for covered repairs.
1
2006/08/17, 11:29
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing
you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.
1
2
3
4
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with
your Primary ID number (your frame number). We’ll be
happy to help you get the Y.E.S. coverage you need.
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)
5
6
7
8
9
9-10
3D1-F8199-11ch9SGML.pmd
10
2006/08/17, 11:29
INDEX
Fuel tank cap ............................................ 3-6
Fuel ........................................................... 3-6
Fuse, replacing ....................................... 6-21
A
Acceleration and deceleration .................. 5-2
Air filter element and check hose, replacing
and cleaning .......................................... 6-12
Pre-operation check list ........................... 4-2
R
Rear brake lever free play, adjusting ..... 6-16
Rear wheel lock ........................................ 3-5
H
Handlebar switches .................................. 3-3
Headlight bulb, replacing ........................ 6-22
Helmet holder ............................................ 3-9
High beam indicator light .......................... 3-2
Horn switch ............................................... 3-4
B
Battery ..................................................... 6-20
Brake lever free play, adjusting .............. 6-15
Brake lever, front ...................................... 3-4
Brake lever, rear ....................................... 3-5
Brake levers, lubricating ......................... 6-17
Brake shoes, checking .......................... 6-16
Braking ...................................................... 5-2
S
Safe-riding points ...................................... 1-4
Safety information ..................................... 1-1
Seat ........................................................... 3-8
Spark plug, checking ................................ 6-6
Specifications ............................................ 8-1
Speedometer unit ..................................... 3-3
Start switch ............................................... 3-4
Starting a cold engine ............................... 5-1
Starting off ................................................. 5-2
Steering, checking .................................. 6-19
Storage compartment (front) ................... 3-9
Storage compartment ............................. 3-10
Storage ...................................................... 7-3
I
Identification numbers .............................. 9-1
Indicator and warning lights ..................... 3-2
C
Carburetor .............................................. 6-13
Care .......................................................... 7-1
Carrier ..................................................... 3-10
Catalytic converter ................................... 3-7
Centerstand, checking and lubricating .. 6-18
Coolant temperature warning light ........... 3-2
Coolant .................................................... 6-11
D
K
Key identification number ......................... 9-1
Kickstarter ................................................ 3-8
L
Labels, location of ..................................... 1-5
Luggage hook ......................................... 3-11
M
Dimmer switch .......................................... 3-4
E
Engine break-in ......................................... 5-3
Engine oil ................................................... 6-8
Engine stop switch ................................... 3-4
F
Main switch/steering lock ......................... 3-1
Maintenance and lubrication, periodic ..... 6-3
Maintenance record ................................. 9-3
Maintenance, emission control system ... 6-2
Maintenance, periodic .............................. 6-1
Model label ................................................ 9-2
P
Final transmission oil .............................. 6-10
Front fork, checking ............................... 6-18
Fuel gauge ................................................ 3-3
3D1-F8199-71idxSGML.pmd
1
Panel, removing and installing .................. 6-6
Parking ...................................................... 5-3
Part locations ............................................ 2-1
1
T
Tail/brake light bulb, replacing ................ 6-23
Throttle cable free play, checking .......... 6-13
Throttle grip and cable, checking and lubricating .......................................................... 6-17
Tires ........................................................ 6-13
Troubleshooting charts ........................... 6-25
Troubleshooting ...................................... 6-24
Turn signal indicator lights ........................ 3-2
Turn signal light bulb, replacing .............. 6-24
Turn signal switch ..................................... 3-4
V
Vehicle identification number .................... 9-1
2006/05/18, 15:35
2
3
4
5
6
7
8
9
INDEX
W
Warranty ................................................... 9-5
Wheel bearings, checking ...................... 6-19
Wheels .................................................... 6-15
1
2
3
4
5
6
7
8
9
3D1-F8199-71idxSGML.pmd
2
2006/05/18, 15:35
1
2
3
4
5
6
7
8
9
3D1-F8199-11ch0SGML.pmd
7
2006/05/15, 19:02
1
2
3
4
5
6
7
8
9
YAMAHA MOTOR TAIWAN CO., LTD
PRINTED IN TAIWAN
2006 .09 - 0.8 * 1 !
(E)
3D1-F8199-11cv.pmd
2
2006/08/17, 11:29
LIT-11626-20-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement