Toshiba FT-2000 Electronic User guide

 TOSHIBA
10 CHANNEL SCANNING CORDLESS TELEPHONE
F1.2000
FT-2500
Should your unit require service, please refer to the
“Toshiba service procedure” in your owner's manual.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury to persons, including the following:
1.
2.
10.
11.
12.
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a dry cloth for cleaning.
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious
damage to the telephone.
Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked
by placing the product on the bed, sofa, rug, or other similar surface. This product should never be
placed near or over a radiator or heat register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your dealer or local power
company. |
Do not allow anything to rest on the power cord. Do not locate this product where the cord will be
abused by persons walking on it.
Do not overload wall outlets and extension cords as this can resultin the risk of fire or electric shock.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid
of any kind on the product.
To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified service
personnel when some service or repair work is required. Opening or removing covers may expose
. you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the
appliance is subsequently used.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following condition: |
A. When the power supply cord plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. Ifthe product does not operate normally by following the operating instructions. Adjust only those
controls, that are covered by the operating instructions because improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
Е. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
CAUTION: TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS BY BATTERY, READ AND
FOLLOW THESE INSTRUCTIONS.
1.
6.
Use only the appropriate type and size battery pack specified in the instruction manual provided for
this product.
Do not dispose of the battery pack in a fire. The cell may explode. Check with State and local codes
for possible special disposal instructions.
Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage
to the eyes or skin. It may be toxic if swallowed.
Exercise care in handling battery in order not to short the battery with conducting materials such as
rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
Charge the battery pack provided with or identified for use with this product only in accordance with
the instructions and limitations specified in the instruction manual provided for this product.
Observe proper polarity orientation between the battery pack and battery charger.
ATTENTION: THE PRODUCT THAT YOU HAVE PURCHASED CONTAINS A RECHARGEABLE
BATTERY. UNDER VARIOUS STATE AND LOCAL LAWS, IT MAY BE ILLEGAL TO DISPOSE OF THIS
BATTERY INTO THE MUNICIPAL WASTE STREAM. PLEASE CHECK WITH YOUR LOCAL GOVERN-
MENT FOR DETAILS IN YOUR AREA FOR RECYCLING OPTIONS OR PROPER DISPOSAL.
SAVE THESE INSTRUCTIONS
DINTRODUCTION
Toshiba America takes pride in presenting the FT-2000/2500, one of the finest telephones available.
Intelligent design, superb craftsmanship, and the latest technological advances have been combined to
provide you with a telephone thatis easy to operate and will provide you with years of dependable service.
Please take the time now to read your Owner's Manual carefully, so that you may enjoy the many
convenient features of your FT-2000/2500 telephone.
FEATURES
e Telephone numbers can be dialed using tones, rotary dial type pulses, or a combination of both.
e Remote channel scan (10 channels) avoid interference.
* Compandor noise reduction circuit minimizes any noise from radio or other appliances as much as
possible.
e Programmable Digital Security Codes (65,536) prevent unauthorized calls.
» Automatic and manual dialing can be combined within the same dialing sequence.
e Up to 20 telephone numbers can be stored in memory, each with a maximum length of 16 digits.
e Pauses may be programmed, where needed, in the middle of an automatic dialing sequence.
* Memory locations can be accessed individually or successively, in any order or combination, all in one
dialing sequence.
e Combination storage is available for simplified memory programming and expanded number range.
« Compatibility with alternate long distance services.
« Automatic Redial button for access to last dialed telephone number (up to 32 digits).
* Designed for use as a wall phone or desk phone.
* Flash function for convenient hook-switch control.
» Hearing Aid Compatibility lets you use your cordless telephone if you wear a hearing aid equipped with
a T (telephone) switch. |
+ Battery low indicator.
* 3 weeks long life battery.
2) LOCATION OF CONTROLS
HANDSET CONTROLS AND FUNCTIONS
Helical Antenna
Speed Dial index Card
(back)
Write all your memorized 8
telephone numbers. ———-
TALK/BATT. LOW LED —-—enumr |
TALK Button — 54 CHANNEL
OEE) Button
|
0-9, x, # Buttons — 1e = Di
OS
EE)
MEMORY Button =» ® P + REDIAL/PAUSE Button
FLASH Button бо об TONE Button
TOSHIBA |i.— Rechargeable Battery
T T Pack (back)
— Charging Contacts
BASE UNIT CONTROLS AND FUNCTIONS
DC Jack
Telephone Modular Jack — TONE/PULSE Switch
fy
+— Base Antenna
Charging Contacts
CHARGE LED POWER LED
@ INSTALLATION
3-1. CONNECTING THE TELEPHONE WIRE
=>, ©® Plug one end of the telephone line cord into the base
modular jack on the rear of the base unit.
@ Plug the other end of the telephone line cord into the
modular wall jack.
Notes
e Never install telephone wiring during a lightning storm.
« Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
* Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
« Use caution when installing or modifying telephone lines.
* If you experience an excessive amount of noise or static, try relocating the base away from the
\_ interference source i.e. TV, radio, appliances.
3-2. CONNECTING THE AC POWER
Connect the plug at the end of the AC adaptor to a standard
120V AC outlet and the other end to the rear of the base unit.
0 Make sure to twine the AC adaptor cord to the strain relief
notch so that the DC jack does not come off by strained force,
also make sure to route the AC adaptor cord where it will not
create a trip hazard, or where it could become chafed and
create fire or other electrical hazards.
Note
| Do not attach the AC power supply cord to building surfaces using metal fittings. |
3-3. INSTALLING THE BATTERY PACK
Installing the battery pack in your FT-2000/2500 is quick and easy. For trouble-free operation, please be
sure to follow the instruction on page 7 “CHARGE THE BATTERY PACK”.
First, remove the battery compartment cover onthe back of the
handset by sliding it down.
O Plug the battery pack's connector into the connector in the
battery compartment.
Notes
® Do not force the connectors together. They fit only one
way.
» With the handset held upright, the black wire should be
to the left side of the battery connection terminal, and the
red wire should be to the right side of the battery
connection terminal.
@ Place the battery pack in the battery compartment.
O Replace the battery compartment cover by sliding it on.
Make sure not to get the wires from the battery pack caught in
( | the cover.
Should the need arise to purchase Parts or Accessories,
please call 1-800-631-3811 for the location of the nearest
parts distributor.
* If replacing the battery, please check with State and local
agencies for disposal of the old battery.
-5-—
3-4. WALL-MOUNTING THE BASE
You can mount your cordless telephone’'sbase unit © Route the telephone wire and AC adaptor cord
on a wall using two provided screws. through the guides on the back of the base unit.
® Cut out the template (see page 7) and use it as X
a guide for placement on the mount screws.
(3'546 inch apart).
O Thread the screws into the wall, letting the
heads extend about '/s inch. Г
1°
| 5 (5mm) |
AC Adaptor Cord Telephone Wire
@ Place the base's keyhole slots over the two
screws and gently push down on the base unit
to lock it into place.
3 25 (1007
16
NN AN AA VAN
- 2 TE
e 5 (5mm)
wAaLLÉ À IA
М m him Ц
AC Adaptor
WALL Cord Telephone
Wire
3-5. USING THE OPTIONAL WALL MOUNT ADAPTOR
This adaptor is designed to be used with the standard bell type
wall mounting system. Align the installation hooks with the slots To telephone
on the wall mount adaptor. Insert telephone in the adaptor and To DC jack modular jack
push down. Then, hook the wall mount adaptor with the base
unit to the modular wall jack.
. Modular wall jack
Note
To order this adaptor please call 1-800-631-3811.
Please see page 14.
Hooks
Wall mount
adaptor
a
To wall outlet
| ‘auoyda;91 1NOA jo uoddns | |
| шпилхещ 110) pnis e ajeoo| buds S(qeuousand |
JO eole UB UI JO pJEOGIIEM uo Bununow jj "y36U841s
E — juersIyNS JO ese ¡EM € Ppajas “Bununouwl 810j8g — T
- INVLHOdWNI
| | ajejdwa) junow [lem |
L 100 — — — — — — — — — — — — — — 1n9 —
3-6. CHARGE THE BATTERY PACK
The supplied Ni-Cd battery packis not charged. Itis important that this battery is charged for 12 to 16 hours
continuously without any interruption before you use the handset for the first time.
During this initial charging of the supplied battery pack or a new battery pack for replacement,
locate the telephone where it can remain completely undisturbed and untouched. Do not hook the
base up to a telephone line for the initial charging sequence.
After installing the battery pack, place the handset on the base unit. The CHARGE LED lights during
charging. If the CHARGE LED does not light, make sure that the AC adaptor is plugged in and the handset
is correctly placed on the base unit.
Notes
* The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the
contacts occasionally with a dry cloth.
* The supplied rechargeable battery pack should last for several years. It, however, eventually it will
deteriorated and lasts only for short time even if it is charged. If this happens, you need to replace
it with a new one. You can order a rechargeable battery pack at your local Toshiba dealer or
authorized parts distributor. Call 1-800-631-3811.
(4 THE BASICS
* Please see page 4, @ LOCATION OF CONTROLS for the location of each button mentioned in this
section.
4-1. TONE-PULSE SELECTION
Set the TONE/PULSE switch located rear of the base unit for the type of service you have (tone or pulse).
If you are not sure which type of service you have, do this simple test.
® Set TONE/PULSE switch to TONE position.
O Press the TALK button on the handset and listen for a dial tone.
O Press any number other than 0. If the dial tone stops, you have Tone service. If the dial tone continues,
you have Pulse service.
@ If you have Pulse service, set TONE/PULSE switch to PULSE position.
4-2. PLACING A CALL
4 | 7 cu
(D Cæ) C3)
(649) (5) (06)
==
\. | oes ce En |
Lift the handset from the base unit, and pressthe Dial the desired phone Wait for the phone you When the other party an-
TALK button. The TALK/BATT. LOW LED!ights. number by pressing the have called to begin ring- swers, you may begin speak-
numbered buttons. ing. ing. To disconnect the call,
returnthe handsettothe base
Note unit or press the TALK but-
The telephone call is cut off when the A.C. power supply fails during a | ton.
conversation, so immediately return the handset to the base unit.
@ After talking on the handset during noisy circumstances, it may occur that the handset is not turned
off even if you pressed the talk key, and it will continue to sound the error tone.
In this case, relocate the handset on the battery charger or press the talk key again close to the base
unit.
@ During a call, do not pull out the battery in the handset. If you do so, the base unit is left to hold the line.
But in case that the handset can not turn the line off due to the electric failure, make the standby mode
by once pulling out the battery and then setting it in.
4-3. ANSWERING A CALL BY USING THE INSTANT TALK FUNCTION
Note
If the handset is already out of the base unit when the
phone begins to ring, you will still have to press the
TALK button to answer your call.
Your phone will ring when someone is calling
your number. Simply lift the handset from the
base unit to answer the call; there is no need
to press the TALK button.
4-4. USING THE CHANNEL SELECTOR BUTTON
Your FT-2000/2500 selects the channel by pressing the CHANNEL button when interference noise is
heard. The TALK/BATT. LOW LED keeps lighting while Talk mode.
Note -
When the channel selection is achieved, the TALK/BATT. LOW indicator turns off for about half
second. If failed, error beep sounds and the channel is not changed.
—8—
4-5. USING THE INSTANT STANDBY FUNCTION
When you have finished with a call, placing the handset back on the base unit automatically causes the
handset to go into Standby mode, and hangs up the phone. There's no need to press the TALK button
to hang up.
Note
If you don’t place the handset back on the base unit, you will need to press the TALK button again to
hang up the phone.
4-6. USING THE REDIAL/PAUSE BUTTON
The REDIAL/PAUSE (RDL/P) button dials the last number (up to 32 digits) that you called. This feature
is extremely useful when the number you called is busy.
To use this feature, simply press the RDUP button immediately after selecting the talk mode. The last
number called will then be dialed again.
Note
If any key is pressed before the RDL/P button, it will not redial. The RDL/P button must be pressed
immediately after selecting the talk mode.
To use this button as a pause function please see page 12, “USING PAUSE FUNCTION”.
4-7. USING THE FLASH BUTTON
The FLASH button is used to send a timed hookflash on the telephone line for accessing services such
as call waiting, etc. (Call Waiting is a telephone company service).
To use this feature, simply press the FLASH button while in the talk mode.
FLASH may also be used to obtain a new dial tone. Be careful not to press “FLASH” during normal
conversation as this will cause your party to be cut off.
4-8. USING THE TONE BUTTON
If you have rotary (Pulse) telephone service, the TONE button allows you to access a computer or
computer-based services such as Sprint, MCI, etc., that respond to Tone signals only.
© Dial the local number to the computer or calling service with the TONE/PULSE switch in the P (pulse)
position.
@ After you have reached the number, press the TONE button and continue to dial your access code or
any other numbers required.
4-9. SETTING THE DIGITAL SECURITY CODE
The Digital Security Code is automatically set when you charge the battery.
If you wish to change the digital security code, make sure the handset is in the Standby mode.
Press the MEM button.
Press any 5 digit number between O to 65535.
Press the MEM button again.
Press the # key. You will hear a long beep tone.
Immediately place the handset in the base unitto complete the code change. This procedure will
change the code in the base unit and the handset. The code can be changed as often as desired.
вес
Note
| An error tone gives warning if you press any number other than 0 to 65535 (such as 66000). )
E
4-10. THE BATTERY LOW LED
When the battery pack in the handset is very low and needs to be recharged, the TALK/BATT. LOW LED
will blink on and off, and in addition the handset will sound a short beep every 3 seconds when in the talk
mode. When this occurs, complete the call that you are making as rapidly as possible, and return the
handset to the base unit for charging.
Note
You must recharge the handset for more than at least one minute to cancel the low battery condition
warning tone.
G MEMORY DIALING
You can store up to 20 of your most frequently-called telephone numbers in memory by using the MEM
button.
5-1. STORING NUMBERS
O Pick up the handset from the base unit. (Do not press the TALK button.)
@ Press the MEM button.
@ Dial the desired telephone number.
@ Press the MEM button.
® Select and press the numbers 01 to 20 for whichever number memory you wish to use.
If you have more telephone numbers to store in memory, repeat the steps from O to O.
® Return the handset to the base unit.
@ Record the telephone numbers on the SPEED DIAL INDEX CARD which is located at the back of the
handset.
EXAMPLE: (MEM) — ® 900 200 © — (MEM) - © O
Notes
* Phone numbers of up to 16 digits (including a digit for a pause or a tone) can be stored. ÓN
* Be sure to listen for the tone or pulsing sound as you press each number. This will ensure that the
number pressed has been properly entered into storage.
* When the number you have entered has been successfully stored, a long beep will be heard.
* If you make any mistakes, then start from step ©.
* If you enter a number that exceeds 16 digits, warning tone will be heard. D
— 10 —
5-2. STORING MIXED TONE/PULSE NUMBERS
Your FT-2000/2500 can also store mixed mode numbers to make it easy to access long distance services.
To store a mixed mode number.
D Make sure the TONE/PULSE switch on the rear of the base unit is in the PULSE mode.
O Press the MEM button (a short beep will be heard), and enter the numbers to be dialed in the PULSE
mode. |
Press the TONE button on the handset and enter the numbers to be dialed in the TONE mode.
When done entering numbers, press the MEM button, and the number of the memory to save the
number in.
You will then hear a long beep when the number has been successfully stored. If you wish to enter a pause
between any of the numbers in the dialing sequence (such as for switchboard delay etc.), press the RDL/
P button at the point you wish to pause in the number sequence. Pressing the RDL/P button more than
once will increase the amount of the delay.
EXAMPLE:
(vEM)-0 © € 92000 -(005-000 ® © © @
~@en-o o
5-3. ERASING A STORED NUMBER
© Pick up the handset. (Do not press the TALK button.)
O Press the MEM button twice.
® Press the desired memory location 01 to 20.
EXAMPLE: (MEM) — (MEM) — © ©
The telephone number stored in(05) will be erased.
5-4. REPLACING A TELEPHONE NUMBER
Just store the new number following the same steps as in STORING.
The new number will take the place of the old one.
5-5. DIALING A STORED NUMBER
To dial a number previously stored in memory,
® Pick up the handset and press the TALK button.
© Press the MEM button.
O Press the memory number 01 to 20.
Your FT-2000/2500 will then dial the previously stored number.
— 11 —
5-6. USING PAUSE FUNCTION
This RDL/P (REDIAL/PAUSE) button is very useful when making an outgoing call through a PBX and using
long-distance services. Each time the RDL/P button is pressed, a pause of about four seconds will be
inserted during the dialing sequence. If more than four seconds are needed, press the RDL/P button twice.
Example: To store the number “0-1234567” in memory for a call through a PBX, follow these steps.
(MEM) > © — (RoLP) © © © OE 9 - (MEM)- O O
Pressing the RDL/P button or resetting the dial mode once is counted as one digit of the number.
5-7. USING CHAIN DIALING
This function is useful in dialing numbers longer than 16 digits.
For example a long distance number and a credit card number could be in 2 memory locations.
* Press the TALK button, MEM (MEMORY) button and a desired memory location (01 to 20) and then
press MEM button and a desired memory location (01 to 20).
Example 1: (2 — (mem) + © — © and then press (MEM) - O @
» MIXED DIAL QUT
Mixing memory dial and manual dialing are possible.
Example 2: CD - (mem)- Grez) anden mes о о В о бб О
Example 3: Ce © © @ ® © © andthen press (MEM) = (01 to 20)
If necessary for further operating instruction, call 1-800-631-3811.
— 12—
(6 SERVICE REQUIREMENTS
If the cordless telephone should malfunction, all repairs will be performed by an authorized Toshiba Service
Station. This unithas been registered within the FCC for direct connection to the telephone network. Under
the FCC program, no customer is authorized to repair this unit. This applies to a unit both in and out of
warranty. If an unauthorized repair is performed, the registration of the unit for direct connection to the
network will be null and void. If the unit is still in warranty, the remainder of the warranty period will also
be null and void.
It is the responsibility of users requiring service to report the need for service to their Toshiba dealer.
@ IMPORTANT INSTRUCTIONS TO USERS
Your FT-2000/2500 has been designed and constructed to conform to federal regulations and can be
connected to the phone line as described in this manual.
Please note that each product connected to the telephone line places a certain load on the line. We
designate this as the unit's “Ringer Equivalence Number”.
It is most unlikely, but . . . If your FT-2000/2500 should cause problems on the phone line, the phone
company has the right to temporarily discontinue your service. If this happens, the phone company will
notify you and give you the opportunity to correct the problem. Also, you need to know that the phone
company does have the right to make changes in their lines and/or equipment.
If these changes might affect your FT-2000/2500 (or require changes in the FT-2000/2500 or its
connection), the phone company will notify you in writing, so you have the chance to take whatever action
necessary to ensure uninterrupted phone service.
O FCC REQUIREMENTS
You are no longer required by the FCC to notify your local telephone company of your intent to connect
a new telephone. Your local telephone company may call you and request information about your phone
such as: the brand name, model number, registration number, and ringer equivalence number. This
information is provided on a label located at the bottom of the base unit and handset.
You may not directly connect your FT-2000/2500 to coin telephone services. Check with your local
telephone company if you wish to connect your FT-2000/2500 to a party line service. Some party line
services require a special adaptor or modification to your telephone.
—13—
© SPECIFICATIONS
HANDSET
Power Source
Battery Life
Dimensions (H/W/D)
Weight
BASE UNIT
Power Source
Dimensions (H/W/D)
Weight
SUPPLIED
ACCESSORIES
OPTIONAL
ACCESSORY
Customer Replaceable Ni-Cd Battery
270mAH 3.6V DC
3 weeks at Standby Mode, after proper initial charging cycle
Approx. 8" x 2-5/16" x 2-1/16" (203 x 59 x 52mm)
Antenna Length 4-3/8" (112mm)
Approx. 7.4 oz (210g)
AC 120V 60 Hz/DC 9V
Approx. 1-11/16" x 4-1/4" x 8-1/16" (43 x 108 x 205mm)
Approx. 9.2 oz (260g)
Rechargeable Battery (1) TRB-6500 Part #. RC003029
AC Adaptor (1) TAC-6500 (Part #. RC002201) for FT-2000 or
TAC-6500BK (Part #. RC002648)
for FT-2500BK
Telephone Cord (1) Part +. RC001861
Owners Manual (1)
Speed Dial Index (1) Part #. RC003560
Wall Mount Screw (2) Part #. RC000936
Wall Mount Adaptor. (1) WMA-3000 (Part #. RC003561) for FT-2000 or
WMA-3000BK (Part #. RC003562)
for FT-2500BK
For purchase of accessories, please call 1-800-631-3811.
(TROUBLESHOOTING GUIDE
Should any problem occur with the set, make the following simple tests to determine whether or not
servicing is required. If the problem persists after you have made these tests, call 1-800-631-3811 for
Customer Service.
Problem Cause
No dial tone 1. AC adaptor of the base unit not plugged into 120 volt AC outlet.
2. Battery is low in power — place the handset in the base unit and
recharge.
3. Telephone line cord detached — check wall jack.
4. TALK button in standby — switch to talk position.
5. Telephone line trouble — check line with a conventional phone.
No calls coming in 1. All of the above except 4.
2. TALK button is in the talk position — switch to standby position.
Static noise on 1. Approaching maximum range of the base unit — make sure that
conversation the base antenna is fully extended. |
2. Outside range of the base unit.
3. Battery is low — place the handset in the base unit and charge.
4, Base located in an area with high interference — relocate the base
unit.
5. General interference from TV, appliances, etc. — move away from
interference source
Battery goes low too
quickly.
Battery not fully charged on initial charge cycle. Battery must be
charged for 12 to 16 hours without any interruption.
— 14 —
TELEPHONE/TELEPHONE ANSWER MACHINE LIMITED WARRANTY
Toshiba America Consumer Products, Inc. (TACP”) and Toshiba Hawaii inc.
(“THI”) make the following limited warranties. These limited warranties extend to
the original consumer purchaser or any person receiving this set as a gift from the
original consumer purchaser and to no other purchaser or transferee.
Limited One (1) Year Warranty
TACP and THI warrant this product and its parts against defects in materials or
workmanship for a period of one year after the date of original retail purchase.
During this period, TACP and THI will repair a defective product or part, without
charge to you. You must deliver the entire set to an Authorized TACP/THI Factory
Service Center. You pay for all transportation and insurance charges for the set
to and from the Factory Service Center.
1 rw ТР
TACP and THI warrant the paris in this product against defects in materiais or
workmanship for a period of one year after the date of original retail purchase.
During this period TACP and THI will replace a defective part without charge to you.
You must also deliver the entire product to one of the Factory Service Centers listed
below. You pay for all transportation and insurance charges for the product to and
from the Factory Service Center.
ner’ !
You should read the owner's manual thoroughly before operating this product.
- Pr ~ How T n Warran
IN THE CONTINENTAL
UNITED STATES...
Should your unit require
service or parts, CALL
Toll Free 1-800-631-3811
Toll Free
1-800-631-3811
Your R nsibil
The above warranties are subject to the following conditions:
(1) You must retain your bill of sale or provide other proof of purchase.
(2) Contact one of the Factory Service Centers for warranty service within (30}
days after you find a defective product or part. You can attain service by
contacting one of the TACP/THI Factory Service Centers listed below.
You must notify a Factory Service Center within thirty (30) days after you
discover a defective product or part.
All warranty servicing of this product must be made by a Factory Service
Center TACP/THI Service Station.
These warranties are effective only if the product is purchased and operated
in the U.S.A.
(3
==
(4
=”
(5
—
(6) Warranties extend only to defects in materials or workmanship as limited
above and do not extend to any product or parts which have been lost or
discarded by you or to damage to products or parts caused by misuse,
accident,improper installation, improper maintenance or use in violation of
instructions furnished by us; or to units which have been altered or modified
without authorization of TACP/THI or to damage to products or parts thereof
which have had the serial number removed, altered, defaced or rendered
illegible.
HAWAII
Toshiba Hawaii Inc.
Service Department
327 Kamakee Street
Honolulu, HI 96814
Phone Number:
(808) 521-5377
IN THE EVENT A PROBLEM SHOULD DEVELOP WITH YOUR PRODUCT, PLEASE PROCEED AS FOLLOWS:
(1) Contact a TACP/THI Factory Service Center for warranty service within thirty
(30) days after you find a defective product or part. You can find an Authorized
TACP/THI Service Station by calling this toll free number 1-800-631-3811 or
by contacting one of the TACP/THI Service Centers listed below.
(2) Arrange for the delivery of the product to the Authorized TACP/THI Service
Station Products shipped to the Service Station must be insured and safely
and securely packed, preferably in the original shipping carton, and a letter of
explaining the defect and also a copy of the bill of sale or other proof of
purchase must be enclosed. Alitransportation and insurance charges must be
prepaid by you.
If you have any question about service, please contact one of the following
TACP/THI Service Centers:
(3
—
EAST SOUTHEAST MIDWEST SOUTHWEST WEST
82 Totowa Road 6115 Jimmy Carter Blvd, 1010 Johnson Drive 1421 Champion Drive 5490A East Francis St
Wayne, NJ 07470-3191 Suite C2, Norcross, Buffalo Grove, IL 60089-6900 Suite 304 Ontario, CA 91761-3622
Phone Number: GA 30071-4607" Phone Number: Carrollton, TX 75006-6871 Phone Number:
Phone Number:
(404) 242-7500
(201) 628-8000 (708) 541-9400
IMPORTANT: PACKING AND SHIPPING INSTRUCTIONS
When you send the product to a service center, you should use the original carton box and packing material, then
insert the original carton box containing the unit into another carton, using more packing material.
Phone Number:
(214) 243-1367
(909) 998-5303
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED WARRANTIES SET FORTH ABOVE. Some stales do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY STATE LAW AS HEREBY
LIMITED, THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS AND SIMILAR
OBLIGATIONS OF MANUFACTURER OR SELLER WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR PARTS.
INNO EVENT SHALL TACP OR THI BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. Some states do not allow the exclusion or limitation of incidental
or consequential damages so the above limitation may not apply to you.
No person, agent, distributor, dealer, service station or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever,
The time within which an action must be commenced to enforce any obligation of TACP and THI arising under this warranty or under any statute, or law of the United
. States or any state thereof, is hereby limited to one year from the date you discover or should have discovered, the defect. This limitation does not apply to implied
warranties arising under state law. Some states do not permit limitation of the time within which you may bring an action beyond the limits provided by state law so the
above provision may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
IMPORTANT
We suggest you record the following information and retain for your records
along with your bill of sale or equivalent document.
Serial no.
Dealer
Model no.
Purchase date
Dealer address
{©1994 TOSHIBA AMERICA CONSUMER PRODUCTS, INC.
UDTS01319ZZ(SKT) RC003566 Printedin Hong Kong
">