advertisement
TV / DVD Combination
Operating Instructions
Models No.
PV-20DF62/PV-27DF62
• Initial Setup and Connection Procedures are on pages 10 to 15.
As an ENERGY STAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect, operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P01).p65
1 2002/04/16, 13:42
Important Safeguards and Precautions
OUTDOOR ANTENNA INSTALLATION
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug. Always hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord.
Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet only one way. If it cannot be fully inserted, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not tamper with the plug.
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly grounded to provide some protection against built up static charges
ANTENNA
LEAD IN
WIRE
and voltage. Section 810 of the National Electrical Code,
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Code) provides information regarding proper grounding of
NEC - NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could be fatal.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against electrical shock, fire or personal injury:
- Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug (polarized or grounding) and must be securely connected.
- Overloaded wall outlets or extension cords are fire hazards.
- Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat generated during operation. If blocked, heat build-up may result in a fire hazard or heat damage to discs.
For your protection: a. Never cover ventilation slots while unit is ON, or operate unit while placed on a bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator, in direct sunlight, inside closed vehicles, in high temperature [over 95
°F (35 °C)], or in over
75% humidity. If unit is suddenly moved from a cold place to a warm one, moisture may condense in unit and on the tape causing damage. Never subject unit to vibration, impact, or place it so that the surface is tilted as internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or stand that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.
• Move any appliance and cart combination with care.
Quick stops, excessive force, and uneven surfaces may cause objects to overturn.
• Carefully follow all operating instructions.
USING THE UNIT
Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug unit and have it inspected by a qualified service technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, odours, or noises.
Immediately unplug unit, and have it inspected by a service technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
Do not put any foreign object on the tray.
• Keep magnetic objects, such as speakers, away from unit to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into unit and cause electrical shock. Any substance, such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the unit does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified by the manufacturer, or have equal safety characteristics as original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a thorough safety check be done as described in the manufacturer’s service literature to ensure video unit is in safe operating condition.
2
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P02-3).p65
2 2002/04/16, 13:42
Safety Precautions/Mesures de sécurité
Warnin
g :
To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Caution :
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement :
Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.
Attention :
Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
FCC WARNING : Any unauthorized changes or modifications to this equipment would void the user’s authority to operate.
This television receiver provides display of television closed captioning.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT LASER
EN CAS D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTICE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this eqiupment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, 'Something About Interference' available from FCC local regional offices helpful.
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: <http://www.eiae.org.>
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this unit, this unit cannot play this disc.
The Region number for this unit is 1.
1
3
20_27DF62 (P02-3).p65
3 2002/04/16, 13:42
Before Using
Congratulations
on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Loading the Batteries
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Features for a Quality Picture
Pure Flat Picture Tube
This unit is equipped with pure flat Picture Tube.
Accessories
OPEN/CLOSE
LIGHT
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
Remote Control
LSSQ0346
Batteries 2 “AA”
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
RETURN
SKIP
+
ZOOM
To order accessories, call toll free
1-800-332-5368.
Apparatus Claims of U.S. Patent Nos.
4,631,603, 4,577,216, and 4,819,098, licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P04 Before).p65
4 2002/04/16, 13:42
Table of Contents
Initial Setup
TV
Important Safeguards and Precautions / Safety Precautions ....... 2 ~ 3
Before Using ........................................................................................ 4
Information (Unit, Disc) .................................................................... 6, 7
Location of Controls ........................................................................ 8, 9
Connections / Initial Setup .......................................................... 10, 11
Reset Language, Channels, Clock, Time Zone Adjust ............... 12, 13
Audio Connections ...................................................................... 14, 15
DVD Operation
DVD
Basic DVD Operation .................................................................. 16, 17
TV Operation
TV
TV Operation ..................................................................................... 18
MTS Broadcast / TV Stereo System .................................................. 19
Closed Caption System ............................................................... 20, 21
TV Timer Features ............................................................................. 22
On-Screen Display (OSD) ................................................................. 23
FM Radio ..................................................................................... 24, 25
Advanced Operation
TV
DVD
Cable Box Universal Remote Control Feature ........................... 26, 27
Special Features ......................................................................... 28, 29
V-Chip Control Feature ............................................................. 30 ~ 33
Video / Audio Menu ........................................................................... 34
Video / Audio Adjustment .................................................................. 35
Disc Operation ........................................................................... 36 ~ 40
DVD Operation using On-Screen Displays .............................. 41 ~ 43
MP3 Playback Operation .................................................................. 44
DVD Lock Feature ............................................................................. 45
Settings for DVD Operation ....................................................... 46 ~ 48
Language Code List .......................................................................... 49
For Your Information
TV
Before Requesting Service ......................................................... 50, 51
Warning and Instruction Displays ..................................................... 51
Limited Warranty ......................................................................... 52, 53
Customer Services Directory ............................................................. 53
Spanish Quick Use Guide / Guía para rápida consulta ........... 54 ~ 61
Index ............................................................................................ 62, 63
5
20_27DF62 (P05 contents).p65
5 2002/04/16, 13:42
Information (Unit, Disc)
Specifications
Display
Picture Tube: 20 inch diagonal pure flat Picture Tube (PV-20DF62)
27 inch diagonal pure flat Picture Tube (PV-27DF62)
Tuner
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22)
Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125
FM Radio
Band range:
General
Power Source:
Power Consumption:
87.5 ~ 108.1 MHz
Television System:
Speaker:
Power Off
Approx. 3.5 watts
EIA Standard NTSC color
2 pieces (5.0W x 2)
Operating Temperature: 5 °C ~ 35 °C (41 °F ~ 95 °F)
Operating Humidity: 10% ~ 75%
Weight: 28 kg (61.6 lbs.) (PV-20DF62)
47 kg (103.4 lbs.) (PV-27DF62)
Dimensions:
120V AC, 60 Hz
Power On
Approx. 113 watts (PV-20DF62)
Approx. 146 watts (PV-27DF62)
604 (W) x 523 (H) x 503 (D) mm
23-13/16” (W) x 20-9/16” (H) x 19-13/16” (D) (PV-20DF62)
760 (W) x 651 (H) x 503 (D) mm
29-15/16” (W) x 25-5/8” (H) x 19-13/16” (D) (PV-27DF62)
Discs played
(1) DVD-VIDEO disc 5” (12 cm) single-sided, single-layer
5” (12 cm) single-sided, double-layer
5” (12 cm) double-sided, double-layer
(one layer per side)
3” (8 cm) single-sided, single-layer
3” (8 cm) single-sided, double-layer
3” (8 cm) double-sided, double-layer
(one layer per side)
(2) Compact disc 5” (12 cm) disc
(CD-DA, VIDEO CD) 3” (8 cm) disc
Digital audio output:
Optical digital output:
Pickup:
Optical connector
Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)
Laser power: CLASS II
Note :Designs and specifications are subject to change without notice.
If the disc cannot be removed...
First, unplug unit.
Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little.
Then, pull the tray all the way out and remove the disc.
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P06-7 Information).p65
6 2002/04/16, 13:42
Disc formats supported by this unit
The unit can play back discs bearing any of the following marks:
DVD
3” (8 cm) disc / 5” (12 cm) disc
Video CD
3” (8 cm) disc / 5” (12 cm) disc
CD
3” (8 cm) disc / 5” (12 cm) disc
Discs which cannot be played with this unit
• DVD with Region No. other than “1” or “ALL”
• DVD of PAL system
• DVD-ROM • DVD-R/DVD-RAM
• DVD-R/DVD-RAM • CD-ROM
• CDV • CD-G
• Do not try to play a Photo CD.
is a registered trademark.
Disc Handling
Handling precautions
• Only hold disc by edges as shown.
Fingerprints, dirt, and scratches can cause skipping and distortion.
• Do not write on label side of disc.
• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.
• Be careful not to drop or bend disc.
• Do not place more than
1 disc on disc tray.
• Do not try to close disc tray when disc is not properly placed.
• Always store discs in their proper cases when not in use.
Disc tray
Disc
Definition of Terms
Angle
Some DVD discs feature scenes simultaneously shot from different angles. The ANGLE button can be used to view the scene from different angles. (ANGLE
Indicator lights up on the unit when a scene recorded at different angles is detected.)
Chapter Number
Titles are subdivided into numbered sections. You can quickly search for a favorite scene using these numbers.
DVD
A high-density optical disc on which high-quality pictures and sound have been digitally recorded.
DVD incorporates new video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.
Playback Control
With Video CD (version 2.0), scenes or information may be selected for viewing or listening from an interactive menu that appears on the TV screen.
Subtitles
Written dialogue which appears at the bottom of the screen.
Time Number
The elapsed play time from the start of a disc or title.
Use to quickly find scenes. (May not work with some discs.)
Title Number
For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number
Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be quickly located.
Video CD
CD containing picture and sound with same quality level as video tape. This unit also supports Video CDs with playback control (version 2.0).
To clean disc surface
With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)
If disc is brought from a cold to a warm environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
7
20_27DF62 (P06-7 Information).p65
7 2002/04/16, 13:42
Location of Controls
Remote Control Buttons
(Light Tower™ Illuminated Remote Control)
OPEN/CLOSE
Opens or closes the disc tray.
POWER
Turns the unit on or off.
FM/TV
Sets to TV mode.
Receives FM radio signal.
MUTE
Mutes the sound instantly.
CHANNEL UP/DOWN
Selects a channel.
SURROUND
Creates a deeper, 3-D sound effect.
NUMBER Keys
Selects a channel directly.
ANGLE
Selects the desired angle in DVD mode.
AUDIO
Selects the desired audio mode.
TITLE
Selects the desired title by number on some DVDs.
SELECT
Controls navigation around on-screen menu.
ACTION
Displays Main Menu.
SET
Sets a selected menu.
SKIP |
Skips back one chapter or track.
Goes to previous menu screen.
PAUSE
Pauses picture in Play mode and frame advance picture in Still mode.
PLAY
Begins playback.
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
DVD
Sets to DVD mode.
LIGHT
See below.
DSS/CABLE
Sets the remote to control some basic DDS or Cable box functions.
TIMER
Sets ON TIMER or SLEEP TIMER.
VOLUME UP/DOWN
Adjusts volume.
RAPID TUNE
Displays the last channel you were watching.
ADD/DELETE/CLEAR
Adds or deletes a channel.
Cancels an item on the screen.
SUB TITLE
Selects a different subtitle language.
DISPLAY/ENTER
Displays the TV status and clock.
In DVD mode, displays disc and unit information.
In DSS or CABLE mode, it may be necessary after channel selection.
MENU
Displays DVD menu.
RETURN
Returns to Menu screen.
SKIP |
Skips one chapter or track.
Goes to next menu screen.
ZOOM
Enlarges specific portions of picture.
STOP
Stops playback.
SLOW/SEARCH
Slow motion picture in Still mode.
Forward/Reverse rapid scene search in Play mode.
Note
• When LIGHT is pressed, (FM/TV, DVD, DSS/CABLE, CH UP/DOWN, VOL+/-) buttons will light for 5 seconds for easy location. If no button is pressed in 5 seconds the light goes out to conserve the batteries.
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P08-9 Location).p65
8 2002/04/16, 13:42
Front View of the Unit and Indicators
PHONES
Connect an earphone or headphones.
AUDIO/VIDEO IN Connector 2
(LINE 2)
Connect from other component.
S-VIDEO IN Connector
Connect from other component with S-Video.
POWER
(See previous page.)
VOLUME UP/DOWN
(See previous page.)
CHANNEL UP/DOWN
(See previous page.)
PAUSE
(See previous page.)
STOP
(See previous page.)
SKIP |
(See previous page.)
Rear View of the unit
SLEEP TIMER Indicator
Lights when the
Sleep-Timer is set.
ON TIMER Indicator
Lights when the On-Timer is set.
ANGLE Indicator
Lights when a scene recorded at a different angle is detected.
Remote Sensor
Aim the remote to this point.
OPEN/CLOSE
(See previous page.)
SKIP |
(See previous page.)
PLAY
(See previous page.)
Disc Tray
Insert a disc to this tray.
AC Power Plug
When plugged into an AC outlet, the unit consumes
3.5 W of electric power in OFF condition.
Optical Digital Audio Output Connector
Connect to a Dolby Digital decoder or dts decoder.
For details, see page 15.
AUDIO/VIDEO OUT Connector
Connect to other component.
20_27DF62 (P08-9 Location).p65
9
* PV-27DF62
Rear shown.
VHF/UHF Antenna Input Terminal
In from your Antenna or Cable.
S-VIDEO IN Connector
Connect from other component with S-Video.
AUDIO/VIDEO IN Connector 1 (LINE 1)
Connect from other component.
9
2002/04/16, 13:42
Initial Setup (Ready to Play)
Please make all cable or antenna connections before powering on.
Connecting
For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/
UHF terminal on the unit.
PV-27DF62 Rear shown.
For DSS/Cable Box
Connect the OUT jack on your cable box to the VHF/
UHF terminal on the unit with a RF cable.
UNIT
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
Cable TV
Converter Box
WARNING:
Overtightening "Nut type" RF coaxial cables may damage jacks.
Finger tighten only.
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
Initial Setup (Ready to Play)
1
2
Plug the unit power cord into an AC wall outlet.
Press POWER* on the remote or unit.
The unit comes on and auto channel and clock set starts.
3
Settings are made automatically.
When setup is done, this screen appears.
2 / 6 / 2002 WED 12 : 00PM
DST : ON
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
CH AUTO SET PROCEEDING
If AUTO CLOCK SET IS
INCOMPLETE screen appears, set the clock using MANUAL CLOCK
SET procedure on next page.
• If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone. If you use a
DSS receiver, it must be turned off.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
AUTO CLOCK SET
PROCEEDING
CANCEL : PRESS STOP KEY
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
2002/04/16, 13:42 20_27DF62 (P10-11 Initial Setup).p65
10
*Important:
If a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
POWER
SELECT
SET
ACTION
OPEN/CLOSE LIGHT
N
U
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
Manual Clock Set
If AUTO CLOCK SET was incomplete, manually set the clock as follows.
SET CLOCK
1
Press ACTION on the Remote to display SET CLOCK
Menu screen.
SELE CT MONTH
DST : ON
SELECT :
SET : SET
END : ACT I ON
2
Press
to select the month and press SET to set. In the same manner, select and set the date, year, time, and DST.
3
Press ACTION twice to start CLOCK and exit.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight
Saving Time.)
■ Spring (First Sunday in April)
DST : ON ->Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST : ON ->Turns clock back one hour.
• If your area does not observe Daylight
Saving Time, select DST:OFF.
Reset all unit Memory Functions
When moving unit to a new location, or if a mistake was made in the Initial Setup section.
Note to CABLE System Installer
This reminder is provided to call the
CABLE (Cable TV) System Installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
1
Turn the unit Power on.
2
Press and hold both PLAY and | on the unit for more than 5 seconds.
• The power will shut off.
3
Perform “Initial Setup” on page 10.
11
2002/04/16, 13:42 20_27DF62 (P10-11 Initial Setup).p65
11
Reset Language, Channels, Clock,
M A I N MENU
1
DVD
LOCK
CLOCK
LANGUAGE
5
3
1
CH TV
SELECT : SET : SET
END : ACT I ON
Press ACTION*
to display MAIN MENU.
2
Language
1) Press to select language icon.
M A I N MENU
Channels
1) Press to select “CH.”
M A I N MENU
Clock
1) Press to select “CLOCK.”
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
2) Press SET repeatedly.
MENU PR I NCIPAL
HOLA
DVD BLOQUEO
RELOJ
ID I OMA
5
3
1
CANAL TV
ELEG I R : F I JAR : SET
TERM I NAR : ACT I ON
For Spanish
MENU
BONJOUR
DVD BLOCAGE
HORLOGE
LANGUE
1
5
3
CANAL TELE
SEL. : REGLER : SET
FIN : ACT I ON
For French
M A I N MENU
HELLO
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
For English
2) Press SET.
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET : SET
END : ACT I ON
3) Press to select
“ANTENNA,” then
press SET to set your antenna system
(“TV” or “CABLE”).
4) Press to select
“AUTO SET,” then
press SET.
• After Channel Auto Set is finished, Clock Auto
Set will be performed.
(If clock is set manually,
Clock Auto Set will not be performed.)
2) Press SET.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET : SET
END : ACT I ON
(“TIME ZONE ADJUST” appears only when auto clock is set.)
3) Press to select
“MANUAL,” then press SET.
(For Auto Clock Set, select “AUTO
CLOCK SET,” and press SET.)
SET CLOCK
2 / 6/
:
DST : ON
SELE CT HOUR
SELECT :
SET : SET BACK :
END : ACT I ON
<Example >
4) Press and press SET to select and set the month, date, year, time, and DST
(Daylight Saving Time)
.
To Make Corrections,
repeatedly press to move to error, then correct.
3) Press ACTION to exit.
5) Press ACTION twice to start the clock and exit this mode.
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P12-13 lang ch clk).p65
12 2002/04/16, 13:42
Time
Time Zone Adjust
*Important:
If a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
Time Zone Adjust
(Only when Auto Clock is set.)
1) Press to select “CLOCK.”
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
2) Press SET.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET :
END : ACT I ON
3) Press to select
“TIME ZONE ADJUST” and press or to subtract or add hour(s) as necessary.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
SET :
END : ACT I ON
4) Press ACTION twice to exit.
• “TIME ZONE ADJUST” returns to “0” if clock is set manually.
ACTION
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
NUMBER keys
ADD/DLT
SELECT
SET
Add or Delete a Channel
To add channel:
Select channel with
number keys and
press ADD/DLT.
To delete channel:
Select channel with
CH or number keys and press ADD/DLT.
CHANNEL 08 ADDED CHANNEL 08 DELE TED
13
20_27DF62 (P12-13 lang ch clk).p65
13 2002/04/16, 13:42
Audio Connections
■
Unit
Speaker
➛
Unit
AUDIO OUT
R L
R L
AUDIO IN
Amplifier
Speaker
Ready Checklist
Turn down the volume, then turn this unit, as well as other equipment to be connected, off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.
Enjoying digital audio output from the digital audio output connector
Notes on audio output from the optical digital audio output connector
Disc
Sound recording format
Optical digital audio output from connector
DVD
Video
CD
CD
MP3
Dolby Digital
Linear PCM
(48/96 kHz
16/20/24 bit) dts
MPEG 1
Linear PCM
MP3
Dolby Digital bitstream
(1-5.1 ch) or OFF (no output)* 1
Linear PCM (2ch)
(48 kHz sampling/16 bit only)* 2 or no output* 1
Bitstream or no output* 1
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)
Linear PCM
(
It depends on the MP3 file
)
*1 The type of audio output from the connector can be selected by the Settings for DVD Operation. (See page 47.)
*2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output from the unit’s optical digital audio output connector.
For your reference:
• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing
Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs.
While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished
Works. © 1992-1997 Dolby Laboratories,
Inc. All rights reserved.
• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same
DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby
Surround mark. For information on Panasonic or
Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
2002/04/16, 13:42 20_27DF62 (P14-15 Audio connect).p65
14
■
Unit
➛
Unit
➛
or
dts
(digital theater systems)
Decoder
➛
When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream is output from the unit Optical digital audio output connector. When the unit is connected to a Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby
Digital decoder or dts decoder is used.]
Notes on connecting an Optical
digital audio cable (optional)
• Firmly connect the cable to the connector.
Unit
Optical digital audio cable (optional)
Dolby Digital Decoder dts processing (optional)
IMPORTANT NOTE:
Caution for optical digital audio output connector:
• When connecting an amplifier (with an Optical digital input connector) which does not contain the Dolby
Digital or dts decoder, be sure to select “OFF” at “Dolby Digital” and
“OFF” at “dts” of the Settings for DVD
Operation “AUDIO OUTPUT” (see page 47). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.
• When a dts decoder is connected, please select “Bitstream” at “dts” of the
Settings for DVD Operation “AUDIO
OUTPUT”. If “OFF” is selected, there will be no sound. (See page 47).
• Video CDs and CDs can be played as normal.
Note:
• Some dts decoders which do not support DVD-dts Interface may not work properly with the unit.
Amplifier
Front
Speaker
Subwoofer
Surround speaker
Centre speaker
Front
Speaker
Surround speaker
15
20_27DF62 (P14-15 Audio connect).p65
15 2002/04/16, 13:42
Basic DVD Operation
Ready Checklist
All connections are made.
Your unit is plugged in.
If unit is connected to an audio amplifier, turn the stereo system’s power on.
POWER
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
OPEN/
CLOSE
DVD
10
1
Press POWER* on the remote or unit.
Insert a disc.
2
• If a disc is already inserted, go to step 3.
(Depending on the disc, playback may start automatically.)
1) Press OPEN/CLOSE.
2) Place disc into disc tray.
1
2
• Hold disc by its edges only
(page 7) with printed side up and use guides to place into
1 2
5” (12 cm) disc.
NUMBER keys
TITLE
AUDIO ANGLE SUB TITLE DISPLAY
TITLE
S E T
ADD/DLT
MENU
SELECT
SET
MENU
3
Press PLAY to start play.
Disc tray closes automatically.
CLOSE
READING
• You may also close the tray by pressing OPEN/CLOSE.
• Data reading time differs with each disc.
PLAY RETURN
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SKIP
+
ZOOM
SKIP
|
<Example>
T I TLE MENU
SKIP |
PAUSE
Cas t l es
SLOW
SLOW/SEARCH
STOP
If an interactive DVD*
1
or a
Video CD with playback control* 2 is used and a TITLE
MENU appears, go to step 5.
Dogs
Love r s B i r ds
SLOW
Operation using unit buttons
4
Press PLAY.
3
Insert disc.
3
•
7
Press
OPEN/CLOSE.
4
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
Dogs of the world
Press
or
number key(s) (see below) to select title and press SET to play.
Using number key(s) starts play automatically.
1
Press POWER
6
Press STOP.
<Example>
<Example> 1 digit number 1 ••• 1
2 digit number 12 ••• 10
➛1➛2
3 digit number 123 •••100
➛1➛2➛3
Press SKIP | or | to go to next or previous menu screen.
• SKIP function not available with all discs.
Please refer to disc jacket for operation information.
To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD)
*
1
*
2
Interactive DVD...
May include multiple camera angles, stories, etc.
Video CD with playback control...
Particular scenes or information can be interactively selected from a menu that appears on the screen.
5
Press STOP to stop play.
6
Press OPEN/CLOSE to eject the disc.
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P16-17 Basic DVD).p65
16 2002/04/16, 13:42
*Important: I f a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
■
Forward/Reverse rapid scene search
➛
or SLOW during play.
➛
• Starting forward/reverse search during play started from menu on Video CDs may recall menu.
• Search speed, slow at first, increases with each additional press of the button up to 5 levels.
■ Forward/Reverse Chapter/Track
Skip
➛
| or | during play.
Each press skips a chapter (DVD) or track (Video CD/CD).
Pressing
|
SKIP once midway through a chapter/track returns to start of that chapter/track.
Each additional press skips back one chapter/ track.
• Pressing SKIP
|
or
|
during play started from menu on Video CDs may recall menu.
Current playback position
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by the unit or the disc.
RESUME function
The unit memorizes the point where STOP is pressed ( flashes on screen).
Press PLAY to resume play from this point.
Pressing STOP again or opening the tray cancels RESUME, however, RESUME is not canceled when power is turned off and on.
• RESUME works only with discs for which elapsed play time is displayed during play.
Auto-Power Off function
Power turns off after unit has been in Stop mode (DVD) for about 5 minutes.
Chapter/Track Chapter/Track Chapter/Track Chapter/Track
Reverse Skip Forward Skip
■ Still (Pause) Picture
➛
➛
• DVD/Video CD : The unit will enter Still picture mode.
• CD : The unit will enter Pause mode.
■ Frame by Frame picture
(DVD/Video CD)
➛
➛
• Each press advances picture one frame.
• Hold down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically (see page 48).
■ Slow Motion picture (DVD/Video CD)
➛
or SLOW
➛ in Still mode.
➛ Press PLAY to release.
• Slow motion speed, slow at first, is increased with each additional press of the button up to 5 levels.
• Reverse slow motion is not available for video
CDs.
Enjoy Video CDs featuring playback control without using menus (Video CDs only)
1. Do steps 1-4 (previous page).
When menu appears, press STOP.
2. Press number key(s) to select desired track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press STOP, and press PLAY, then the menu appears. Now, go to step 5 (previous page).
Notes
• Please read the disc jacket for operation information.
• If a single sided disc is placed in upside down,
“PLEASE CHECK THE DISC,
AND FOR STAINS OR SCRATCHES ON
DISC” is displayed.
• Remove disc and press unit POWER off when not in use.
• Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu.
17
20_27DF62 (P16-17 Basic DVD).p65
17 2002/04/16, 13:42
TV Operation
*Important: If a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
1
Press POWER* on the remote or unit.
Ready Checklist
All connections are made.
Your unit is plugged in.
2
0 8
Use CH
or
number keys to select a channel.
VOL + / VOL -
POWER
3
Press VOL + or VOL - to adjust volume.
24
PHONES
Jack
CH
■ Using the 100 key
When selecting CABLE channels 100 to 125 with the number keys, first press the 100 key, and then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you were watching.
■ Audio Mute
Press MUTE to instantly mute the sound.
Press again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack.
POWER
CH
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
NUMBER keys
100 key
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
VOL + /-
RAPID
TUNE
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P18 TV).p65
18 2002/04/16, 13:42
MTS Broadcast / TV Stereo System
®
Equipped with -TV Noise
Reduction for true MTS reproduction.
®
-TV Noise
Reduction is required for good stereo separation and audio fidelity.
®
is a registered trademark, and is licensed by
®
Technology
Licensing.
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
AUDIO
DISPLAY
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow. To change the audio mode for these broadcasts, see the “Select Audio Mode for TV Viewing” section (below.)
Press DISPLAY to display the broadcast signal being received.
STEREO
SAP
MONO
1 2 : 0 0AM
CH08
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo
(main language) and Secondary Audio
Program (sub language) broadcasts are being received simultaneously.
Select the STEREO or SAP audio mode.
STEREO
SAP
MONO
1 2 : 0 0AM
CH08
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.
• If stereo broadcast is weak and the display flickers, select MONO audio mode for possible improvement.
STEREO
SAP
MONO
1 2 : 0 0AM CH08
SAP broadcast
Secondary Audio Program
(sub language).
Select SAP audio mode for the sub language.
STEREO
SAP
MONO
1 2 : 0 0AM CH08
MONO broadcast
Normal monaural sound broadcast.
20_27DF62 (P19 MTS).p65
Audio Mode for TV Viewing
Press AUDIO to select the desired audio mode as described above.
(Arrow shows selection.)
• Each press of AUDIO will change the audio mode as shown below.
• “SAP” is selected with first press of AUDIO.
< Example >
Press AUDIO
STEREO
SAP
MONO
1 2 : 0 0AM CH08
STEREO
SAP
MONO
1 2 : 0 0AM
CH08
STEREO
SAP
MONO
1 2 : 0 0AM
CH08
Press AUDIO
Press AUDIO
19
19 2002/04/16, 13:42
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
Press ACTION*
to display MAIN MENU.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
1
3
5
CH TV
SELECT : SET : SET
END : ACT I ON
1) Press select “TV.”
to
2) Press SET to display SET UP
TV screen.
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
1) Press to select “CAPTION”.
2) Press SET to display
CAPTION screen.
Closed Caption Mode Selections
Caption Mode: CAP C1 or C2
A narration of selected TV programs is displayed.
Check TV program listings for CC
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
Most of the screen will be blocked out. When the TV station broadcasts information, such as program listings, it will appear in this space.
Caption Mode: OFF
Closed Caption /Text narration will not be displayed.
NOTE :
The closed caption or text signal may be broadcast over C1, C2, or both.
Also, text contents can vary so you may wish to try different settings.
4
CAPT I ON
CAPT I ON MODE : CAP C1
CC ON MUTE : CAP C1
SELECT :
SET : SET
END : ACT I ON
1) Press to select CAPTION
MODE.
2) Press SET repeatedly to select mode. (See right.)
TEXT C2
OFF CAP C1
TEXT C1
CAP C2
5
Press ACTION three times to return to the normal screen.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P20-21 TV CC).p65
20 2002/04/16, 13:43
*Important: I f a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
MUTE
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
CH
VOL
DSS
CABLE
TIME
R
VOL
+
CH
R
-T
U
N
Caption On Mute Feature
Closed Caption narration, if available, is displayed when MUTE button is pressed for silence.
1
Press ACTION
to display MAIN MENU.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
1
5
3
CH TV
SELECT : SET : SET
END : ACT I ON
1) Press select “TV.”
to
2) Press SET to display SET UP
TV screen.
SELECT
SET
ACTION
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
1) Press to select “CAPTION”.
2) Press SET to display CAPTION screen.
4
CAPT I ON
CAPT I ON MODE : OFF
CC ON MUTE : CAP C1
SELECT :
SET : SET
END : ACT I ON
1) Press to select CAPTION
MODE.
2) Press SET repeatedly to select “OFF.”
5
NO CAP C1
CAP C2
1) Press to select
CC ON MUTE.
2) Press SET repeatedly to select desired mode.
• Each press of SET will change the display as shown left.
• The caption may be broadcast over CAP
C1 or C2.
Note
• When a disc supporting closed caption is used, the subtitle and the closed caption may overlap. In this case, turn the subtitle or caption on mute mode off.
(See page 36.)
6
Press ACTION three times to return to the normal screen.
7
Press MUTE to mute the sound and display closed captioning.
• To cancel, press MUTE again.
21
20_27DF62 (P20-21 TV CC).p65
21 2002/04/16, 13:43
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 3 modes (TV, FM radio, or DVD/Video CD/CD.)
You can also combine the On-Timer with a one minute alarm that gradually increases in volume.
1
Press TIMER*
to display SET TIMER screen.
2
SET T I MER
ON T I MER
S LEEP T I MER : 00
SELECT :
SET : SET
END : T I MER
1) Press to select
“ON TIMER.”
2) Press SET to display
ON TIMER screen.
Ready Checklist
The clock is set to correct time.
ON TIMER Indicator
SLEEP TIMER Indicator
3
ALARM : ON
SELE CT HOUR
SELECT :
SET : SET
END : T I MER
• ON-TIMER mode selection order
CH01
CH02 CH03
DVD
ON T I MER
FM9
CH125
FM1
1) Press to select desired settings.
2) Press SET to set the
ON-TIMER TIME or
ON-TIMER mode.
• Make sure a disc is inserted if DVD (DVD/Video CD/CD) mode is selected.
• See “FM Radio” on pages
24 and 25 for instructions on how to preset FM stations.
FM8
This unit can be set for auto power off.
1
Sleep Timer
Press TIMER to display SET
TIMER screen.
4
ON T I MER
Press
to select
ALARM “ON” or “OFF.”
2
SET T I MER
ON T I MER
S LEEP T I MER : 00
SELECT :
SET : SET
END : T I MER
SLEEP TIMER 30 60 90 00
1) Press to select
SLEEP
TIMER.
2) Press SET repeatedly to select the desired time.
ALARM : ON
SELECT ALARM
CANCEL : ADD / DLT
SELECT :
SET : SET BACK :
END : T I MER
When “ON” is selected,
an alarm will gradually increase in volume for one minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
use and to move back and correct.
5
Press TIMER to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights up on the unit.
To cancel,
press SET repeatedly until 00 appears.
3
Press TIMER to return to the normal screen.
• Pressing DISPLAY with sleep timer set displays remaining time.
• SLEEP TIMER Indicator lights up on the unit.
Note
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear the time in step 3. Now, press TIMER to end.
“ON TIMER END” briefly appears on-screen.
• If no button on the remote or unit
(including a button used to turn off the alarm) is pressed within 60 minutes after unit turns itself on, it will turn itself back off.
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P22 TV Timer).p65
22 2002/04/16, 13:43
On-Screen Display (OSD)
*Important:
If a remote control button does not work when pressed, press the
FM/TV button on the remote and try the button again.
TV Status & Clock Display
Press DISPLAY
to display or remove the overlay.
Channel
Current Time
Receivable
Broadcast Types
(See page 19.)
STEREO
SAP
MONO
1 2 : 0 0AM CH08
OPEN/CLOSE LIGHT
N
U
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
TIMER
ADD/
DELETE
Blue Screen Display
Whenever the selected channel has no broadcast signal with the Weak Signal Display
Feature set to “OFF” (see page 28), the screen will turn solid blue.
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
DISPLAY
SELECT
SET
Channel Display
When you change channels, the channel number will be displayed.
0 8
20_27DF62•@(P23 VCR status ).p65
23 2002/04/16, 13:43
23
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz. You can even set the On-Timer (page 22) to wake up to your favorite radio station.
FM Radio Setup
1
2
Press FM/TV on the remote to display FM radio mode.
1 2 : 0 0PM
FM 1 87. 5MHz
Press a number
key* (1~9) to select the FM preset number.
1 2 : 0 0PM
3
FM 1 8 7. 7MHz
MEMORY : PRESS ADD / DLT KEY
1 2 : 0 0PM
FM 1 8 7. 7MHz
MEMOR I ZED
To Make Corrections,
select station with a number key, then do step 3 again.
To exit FM mode, press
FM/TV or DVD on the remote.
1) Press CH to select the desired radio station.
(Each press changes frequency by 200
KHz.)
2) Press ADD/DLT to set the radio station.
Hold down CH or
for a few seconds, then release to quickly scan for FM stations in your area.
• To cancel, press
CH or while in search mode.
CH
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P24-25 FM).p65
24 2002/04/16, 13:43
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP PLAY SKIP
+
PAUSE STOP
SLOW/SEARCH
ZOOM
FM/TV
DVD
CH
NUMBER keys
ADD/
DELETE
DISPLAY
AUDIO
SELECT
SET
ACTION
FM Antenna Setup
Make sure FM tuning is done correctly (see FM Radio Setup).
1
Press ACTION
to display MAIN MENU.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
1) Press to select “TV.”
2) Press SET to display SET
UP TV screen.
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
■ For cable TV users
➛ “INT”
■ For antenna users
➛ “EXT”
1) Press to select
FM ANTENNA.
2) Press SET to select “INT
(INTERNAL)” or
“EXT (EXTERNAL)” to determine which one sounds best.
4
Press ACTION twice to end setup.
Audio Mode for FM Radio
1 2 : 0 0PM
STEREO
MONO
FM 1 8 7. 7MHz
Press AUDIO
repeatedly to select
“STEREO” or
“MONO” in FM
Radio mode.
Notes
• You may get better reception by repositioning the unit.
• You cannot select FM Radio mode while a blue back screen (ACTION,
MENU) is displayed.
• Once stations are set, the selected station and current time are displayed when FM Radio mode is entered. To remove time, press DISPLAY.
Using FM Radio
1
Press FM/TV on the remote to display FM radio mode.
2
1 2 : 0 0PM
FM 1 87. 5MHz
Press a number key
(1~9) to select a preset FM number
(see FM Radio Setup on page 24).
To exit FM mode,
press FM/TV or DVD on the remote.
25
20_27DF62 (P24-25 FM).p65
25 2002/04/16, 13:43
Cable Box Universal Remote Control Feature
Universal Remote Control is...
The Remote Control may be set up to control some basic DSS or Cable box functions.
The Universal Remote Control Setup
1
Find your DSS box or Cable box
Brand Code Number from one of the charts on the next page.
2
Setup remote.
Hold down DSS CABLE and press
number keys to enter code.
• If code number is 100 or greater, e.g., press 1 - 0 - 2 for 102.
POWER
FM/TV
DVD
DSS
CABLE
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
3
Confirm code entry.
Press POWER to turn selected unit
ON or OFF.
• See below for controllable functions in each mode.
Notes
• Please repeat the Universal Remote Control Setup after replacing remote control batteries.
• The remote control will not operate all DSS receivers or Cable Boxes made by the manufacturers listed.
If you get no results, your particular brand cannot be controlled.
NUMBER keys
ENTER
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
Using the Universal Remote Control
(Available Buttons / Functions)
Once the remote control has been properly set up, you can select FM/TV, DVD, DSS or CABLE mode depending on which functions you wish to control.
Press FM/TV, DVD or DSS CABLE
on the remote control to select the desired mode. (See below for buttons available in each mode.)
Set to FM/TV, DVD:
All TV, FM, and DVD functions.
Set to DSS CABLE:
• CABLE/DSS function, e.g. POWER, ENTER,
NUMBER keys (except 100 key), CH UP/DOWN.
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P26-27 Univ rem).p65
26 2002/04/16, 13:43
DSS Brand Code Numbers
Toshiba ........................................................... 90
Hitachi/ Hughes ........................................ 91, 99
Primestar ........................................................ 92
Drake .............................................................. 93
Magnavox ................................................. 94, 95
Uniden ....................................................... 94, 95
Optimus .................................................... 94, 95
Panasonic ....................................................... 96
ProScan .......................................................... 97
RCA ................................................................ 97
SONY ...................................................... 98, 105
Cable Box Brand Code Numbers
Archer ....................... 44, 06, 01, 120, 05, 63, 126
Cableview ...... 29, 09, 01, 63, 120, 44, 42, 30, 52,
04, 124, 126
Citizen ................ 44, 52, 30, 63, 42, 04, 124, 126
Curtis ................................. 08, 09, 25, 61, 53, 87
Century .................................. 44, 51, 75, 59, 126
Cabletenna ............... 29, 09, 01, 63, 120, 44, 126
Cable Cinema ........... 29, 09, 01, 63, 120, 44, 126
Diamond ................... 29, 09, 01, 63, 120, 44, 126
Eagle .................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern .............................................. 28, 29, 130
Explorer ............................. 08, 09, 25, 61, 53, 87
Gemini ............................................... 30, 04, 124
General Electric ................................. 01, 57, 120
General Instruments .... 01, 84, 83, 34, 03, 02, 04,
55, 65, 66, 67, 68, 120, 106, 121, 122, 115, 117,
118, 124
Gerrard .......................................... 44, 51, 75, 59
GC Electronics ............. 44, 42, 63, 29, 30, 52, 04,
124, 126
Hamlin ............ 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ............................................................. 31
Jerrold ........ 01, 84, 83, 34, 03, 02, 04, 55, 65, 66,
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ................................................. 30, 04, 124
Macom ............................................................ 31
Magnavox ................................................ 26, 112
Matsushita ............................. 17, 16, 08, 87, 109
Movietime ................... 32, 39, 42, 44, 126, 38, 40
Maestro ..................................................... 74, 35
NEC .............................................. 40, 19, 38, 32
NSC .............................................. 40, 19, 38, 32
Novavision ......................... 08, 09, 25, 61, 53, 87
Next Level ............. 01, 84, 83, 34, 03, 02, 04, 55,
65, 66, 67, 68, 120, 106, 121, 122
Oak ........................................... 46, 11, 129, 101
Oak Sigma ................................. 46, 11, 129, 101
Panasonic .............................. 17, 16, 08, 87, 109
Philips ................. 23, 24, 20, 13, 07, 50, 128, 129
Pioneer ................................................ 06, 05, 12
Pulsar ................. 04, 42, 63, 44, 30, 52, 124, 126
Quest .................................................. 06, 05, 12
Radio Shack ........................... 44, 51, 75, 59, 126
RCA ....................................... 17, 16, 08, 87, 109
Realistic .................................. 44, 51, 75, 59, 126
Recoton .................................. 44, 51, 75, 59, 126
Regal .............. 41, 14, 15, 28, 102, 104, 103, 130
Regency ............................................ 28, 29, 130
Rembrandt ... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung .................................. 42, 06, 32, 05, 40
Scientific Atlanta ................. 08, 09, 25, 61, 53, 87
Sheritech ......................................................... 27
Signal ...................................................... 26, 112
SL Marx .......... 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ................................... 17, 16, 08, 87, 109
Standard Components ........... 32, 39, 42, 44, 126
Stargate ........... 04, 42, 32, 40, 63, 44, 30, 52, 06,
124, 126
Sylvania ..................................................... 19, 18
Teknika ...................................................... 74, 35
Telecaption .............................................. 77, 127
Teleview ............................. 40, 19, 38, 32, 42, 06
Texscan ..................................................... 19, 18
Tocom .............................. 34, 33, 01, 42, 66, 120
Toshiba ........................................................... 36
Unika ........................ 44, 42, 63, 29, 01, 126, 120
Universal .......................... 52, 43, 44, 63, 42, 126
Viewstar ............... 62, 40, 22, 13, 58, 20, 26, 107
Videoway ...................................... 07, 23, 50, 129
Vidtek .............................................................. 64
Zenith ........................................... 07, 23, 50, 129
Notes
• In DSS or CABLE mode, it may be necessary to press ENTER after pressing number keys for channel selection.
• In DSS or CABLE mode, POWER, CH Up/Down, Number Keys, ACTION, TIMER,
DISPLAY/ENTER, SEARCH, SKIP+/-, R-TUNE, SELECT, SET, ZOOM, ANGLE, AUDIO,
TITLE, SUB TITLE, MENU, or ADD/DLT/CLEAR are not available. Press FM/TV, DVD to use these functions.
• Depending on your DSS receiver or Cable box brand, some of the functions listed may not be remote controllable.
• Some DSS receiver or Cable box brands require you to turn on the power manually.
• Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does not respond to the first code, please try the next one.
27
20_27DF62 (P26-27 Univ rem).p65
27 2002/04/16, 13:43
Special Features
Remote Warning Feature
When Universal Remote Control (page 26) is used, and this feature is set to “ON,” a warning appears whenever an invalid key is pressed in DSS or Cable mode.
1
2
Press ACTION* to display MAIN MENU.
M A I N MENU
DVD
TV
LOCK
CLOCK
LANGUAGE
5
3
1
CH
1) Press to select “TV.”
2) Press SET to display SET UP
TV screen.
SELECT : SET : SET
END : ACT I ON
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
1) Press to select REMOTE
WARNING.
2) Press SET to set “ON” or “OFF.”
• “REMOTE WARNING : OFF”
➛ Remote warning will not appear even if invalid key is pressed.
4
Press ACTION twice to return to normal screen.
Selecting Input Mode
Method 1:
Press CH
. The display will change as follows.
LINE2
1 2 3
LINE1
(CABLE)
125 or
(TV)
69
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV”, then press
SET for SET UP TV screen.
c Press
to select “INPUT SELECT,” and then press SET to select “TUNER,”
“LINE1,” or “LINE2.”
d Press ACTION twice to exit this mode.
Weak Signal Display Feature
When “ON” is selected, the picture is displayed even when a broadcast signal is weak or nonexistent.
1
Press ACTION
to display MAIN MENU.
2
DVD
TV
M A I N MENU
LOCK
CLOCK
LANGUAGE
5
3
1
CH
SELECT : SET : SET
END : ACT I ON
1) Press to select “CH.”
2) Press SET to display SET
UP CHANNEL screen.
SET UP CHANNEL
3
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET : SET
END : ACT I ON
1) Press to select WEAK
SIGNAL
DISPLAY.
2) Press SET to set “ON” or
“OFF.”
Notes
• “ON” = Picture is displayed regardless of signal condition, and may not always be clearly visible.
“OFF” = Screen turns solid blue when signal is absent or weak.
• If unit is connected to equipment which has blue back feature, selecting “ON” will have no effect on the other equipment.
4
Press ACTION twice to return to the normal screen.
CH
SORROUND
OPEN/CLOSE
LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
ADD/DELETE
Auto Operation Functions
ADD/DLT
■ Auto Shut Off
No broadcast signal in TV mode (Only when Weak Signal Display is set to OFF.),
DVD stops for 5 minutes
➛ Power turns off
• This feature is canceled if any button is pressed during above conditions.
SELECT
SET
ACTION
AUDIO
TITLE
ACTION
SKIP
PAUSE
ANGLE SUB TITLE
S E T
PLAY
STOP
DISPLAY
MENU
RETURN
SKIP
+
ZOOM
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P28-29 Special).p65
28 2002/04/16, 13:43
*Important: I f a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
Channel Caption
Channel Caption is ...
Station names, e.g. ABC, CNN, etc. are set so they will appear when a channel is selected.
Choose 24 preset names.
You need a list of stations and the channel numbers you receive them on.
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
DVD
TV
LOCK
CLOCK
LANGUAGE
5
3
CH
1
SELECT : SET : SET
END : ACT I ON
1) Press select “CH.”
to
2) Press SET to display SET UP
CHANNEL screen.
SET UP CHANNEL
3
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET : SET
END : ACT I ON
1) Press to select CHANNEL
CAPTION.
2) Press SET to display screen.
DVD Volume Adjust
Audio recorded on a DVD or Video CD often incorporates a dynamic range of sound. This means that, when compared to a music CD, etc., the average volume is generally lower and the peaks may be higher. This unit can be set so that the volume is increased automatically.
1
Press ACTION
to display MAIN MENU.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
1) Press to select “TV.”
2) Press SET to display SET
UP TV screen.
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
1) Press to select DVD
VOL ADJUST.
2) Press SET to set the level
(0, +1, or +2).
4
Press ACTION twice to return to normal screen.
4
CHANNEL CAPT I ON
ABC
CBS
FOX
NBC
- -
- -
- -
- -
- -
- -
- -
- -
PBS
CNN
ESPN
HBO
- -
- -
- -
- -
1) Press to select a station.
2) Press SET (or ) to move cursor
SELECT :
SET : SET
END : ACT I ON to the right.
3) Press to select channel
CHANNEL CAPT I ON
ABC
CBS
FOX
NBC
PBS
CNN
ESPN
HBO
CLEAR : ADD / DLT
SELECT : number.
4) Press SET (or
) to set preset captions.
END : ACT I ON
• Repeat step 4 until the Caption
List is complete.
To Make Corrections
Press , then SET (or ) to select channel number.
Press to change, or ADD/DLT to delete.
Surround Sound System
You can hear a deeper, 3-D sound effect using just the unit’s two front speakers.
Set Surround sound.
SURROUND ON
Press SURROUND.
• “SURROUND ON” is displayed.
SURROUND OFF
To Cancel,
press SURROUND.
5
Press ACTION three times to end setup.
Notes
• Surround sound effect is not available for normal (mono) broadcasts.
• The surround effect (TV mode only) is not output to Audio Output L/R Connector.
29
20_27DF62 (P28-29 Special).p65
29 2002/04/16, 13:43
V-Chip Control Feature
V-Chip Control Feature is...
This unit has a built-in V-Chip Control which allows you to block unwanted TV usage based on US
MOVIES and US TV PROGRAMS Ratings.
Process of V-Chip Control Feature
Enter Code
Setup Blocking
Enter Secret Code
A 4-digit code must be entered to view a blocked program or change rating settings.
1
Press ACTION* to display MAIN MENU.
2
M A I N MENU
DVD LOCK LANGUAGE
5
3
CH
1
TV CLOCK
SELECT : SET : SET
END : ACT I ON
1) Press to select “LOCK.”
2) Press SET to display
LOCK screen.
3
LOCK
ENTER 4-D I G I T CODE
- -
BACK SPACE:
ENTER : 0
-
9
END : ACT I ON
To Make Corrections
Press repeatedly to move the cursor.
Press number keys to make the correction.
1) Press number keys to enter your secret code.
2) Enter same code again for confirmation.
• Step 2) not necessary when changing rating or secret code.
• Take care that you are not observed entering the secret code.
4
LOCK
CONF I RM 4-D I G I T CODE
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE : SET
END : ACT I ON
Press SET to display
US Ratings menu (see pages 31, 32).
Or
Press ACTION twice to exit.
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP PLAY
PAUSE STOP
SLOW/SEARCH
SKIP
+
ZOOM
NUMBER keys
CLEAR
SELECT
SET
ACTION
Changing your secret code
• You will need your current code.
Do steps 1 ~ 3. In step 4, press CLEAR to clear current code.
Repeat steps 3 and 4 to enter new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted programs cannot be accessed unless the secret code is entered.
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P30-33 V-chip).p65
30 2002/04/16, 13:43
*Important: I f a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
If LOCK menu is not displayed, perform
“Enter Secret Code” steps on page 30.
Process of V-Chip Control Feature
Enter Code
Setup Blocking
US MOVIES Ratings
1
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
1) Press to select
US MOVIES.
2) Press SET to set
“ON” or “OFF.”
➛
■ “OFF” ➛
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting menu. Not necessary except when viewing Canadian discs or broadcasts.
2
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
1) Press to select
CHANGE
SETTINGS.
2) Press SET to display screen.
3
1) Press to select
VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign movies usually have no ratings.
4
1) Press to select and SET to set ratings to be blocked.
(See ratings chart on this page.)
5
Press ACTION to redisplay LOCK menu and continue with US TV PROGRAMS
Ratings Setup (page 32).
Or, press ACTION four times to exit.
G
US MOVIES RATINGS
GENERAL AUDIENCE:
All ages admitted.
PG PARENTAL GUIDANCE:
Some material may not be suitable for children.
PG-13 PARENTS CAUTIONED:
Some material may be inappropriate for children under 13.
R RESTRICTED:
Children under 17 must be accompanied by a parent or adult.
NC-17 OVER AGE 17 ONLY:
No one 17 and under admitted.
X ADULTS ONLY:
31
20_27DF62 (P30-33 V-chip).p65
31 2002/04/16, 13:43
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do
“Enter Secret Code” steps on page 30.
Process of V-Chip Control Feature
Enter Code
Setup Blocking
1
2
US TV PROGRAMS Ratings
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
1) Press * to select US TV
PROGRAMS.
2) Press SET to set
“ON” or “OFF.”
➛
➛
Note
• “NEXT PAGE” displays CANADIAN V-Chip setting menu. Not necessary except when viewing Canadian discs or broadcasts.
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
1) Press to select CHANGE
SETTINGS.
2) Press SET to display screen.
US TV PROGRAMS RATINGS:
Chart 1
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
FOR ALL CHILDREN:
Content specifically geared to young viewers ages 2-6.
FOR AGE 7 AND OLDER:
May contain mild physical or comedic violence which may frighten children under 7.
GENERAL AUDIENCE:
Contains little or no violence, strong language, or sexual dialogue or situations.
PARENTAL GUIDANCE:
May contain infrequent coarse language, limited violence, some suggestive sexual dialogue and situations.
PARENTS CAUTIONED:
May contain sophisticated themes, sexual situations, strong language, and more intense violence.
MATURE AUDIENCE:
May contain mature themes, profane language, graphic violence, and sexual situations.
3
V I EW NR PROGRAMS? : YES
TV-Y
TV-Y7 FV
UNLOCKED
TV-G
TV-PG
TV-1 4
TV-MA
V S L D
V S L D
V S L
CONTA I NS NO RAT I NG
SELECT : SET : SET
END : ACT I ON
1) Press to select VIEW NR
PROGRAMS?.
2) Press SET to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports, weather, bulletins, emergency information usually have no ratings.
US TV PROGRAMS RATINGS:
Chart 2
FV
V
S
L
D
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
4
V I EW NR PROGRAMS? : YES
TV-Y
TV-Y7 FV
UNLOCKED
TV-G
TV-PG
TV-1 4
TV-MA
V S L D
V S L D
V S L
FOR ALL CH I LDREN
SELECT : SET : SET
END : ACT I ON
Note
• You may select from standard TV ratings
(chart 1), or customize to a specific content rating (chart 2).
1) Press to select and SET to set ratings to be blocked.
(See ratings charts on this page.)
• Ratings highlighted in
Green will be blocked.
Ratings in white letters will not be blocked.
5
Press ACTION four times to exit this mode.
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P30-33 V-chip).p65
32 2002/04/16, 13:43
*Important: I f a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
OPEN/CLOSE
LIGHT
N
U
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
SELECT
SET
ACTION
Process of V-Chip Control Feature
Enter Code
Setup Blocking
Blocking Message
<When V-Chip Control is activated>
RAT I NG : PG-1 3
ACCESS CODE ----
ENTER : 0-9
ABC
PROGRAM RAT I NG EXCEEDED
• If a program or movie exceeds the ratings you have set, a message will appear on a black background and sound is muted.
To View a Blocked Program/Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in the Blocking Message screen.
• V-Chip Control is reactivated when power is turned off or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-4 page 30).
Then, set US MOVIES and/or US TV
PROGRAMS to “OFF” using and SET.
(Ratings set on pages 31, 32 is retained and will be in effect when V-Chip Control is activated again.)
20_27DF62 (P30-33 V-chip).p65
33 2002/04/16, 13:43
33
Video / Audio Menu
*Important:If a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
This feature allows easy setting of picture and sound suitable for each program source.
Video Menu
1
2
Press ACTION* to display MAIN
MENU.
M A I N MENU
DVD
LOCK
CLOCK
LANGUAGE
5
3
1
CH
1) Press to select “TV.”
2) Press SET to display SET UP
TV screen.
TV
SELECT : SET : SET
END : ACT I ON
Audio Menu
a
Do steps 1 - 3 left.
b
SET UP V I DEO / AUD I O
V I DEO MENU : NORMAL
V I DEO ADJUST
AUD I O MENU : MUS I C
AUD I O ADJUST
SELECT :
SET : SET
END : ACT I ON
1) Press to select “AUDIO
MENU.”
2) Press SET to select desired mode.
(See below.) c
Press ACTION three times to end setup.
3
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
4
SET UP V I DEO / AUD I O
V I DEO MENU : NORMAL
V I DEO ADJUST
AUD I O MENU : MUS I C
AUD I O ADJUST
SELECT :
SET : SET
END : ACT I ON
1) Press to select “SET UP
VIDEO/AUDIO.”
2) Press SET to display.
1) Press to select “VIDEO
MENU.”
2) Press SET repeatedly to select desired mode. (See below.)
5
Press ACTION three times to end setup.
[Audio Menu]
■
■
[Audio AGC (Auto Gain Control)]
The sound level is automatically adjusted to
■ suit the program source (see below left).
■ MOVIE
■
Sound suited to movies.
■ MUSIC
■
Sound suited to music. (Factory setting)
■ SPEECH
Sound suited to dialogue.
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
[Video Menu]
■ NORMAL
Factory setting.
■ MOVIE
Picture is adjusted for a movie-like feel.
■ NIGHT
Color and picture intensity are adjusted to be easier on the eyes for night viewing.
S E T
ACTION
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
RETURN
SKIP
+
ZOOM
SELECT
SET
ACTION
Volume level
High
Standard
Low
TV
CD
TV
Volume level
High
Standard
TV
CD
TV
Low
AUDIO MENU : NORMAL AUDIO MENU : AUTO
<Audio AGC Example>
Notes
• The effects of this feature on the signal is not output to the Audio/Video Output Connector.
• When AUDIO MENU mode is “AUTO,” the
AUDIO ADJUST setting will be “STANDARD.”
• AUDIO MENU settings remain in memory.
• VIDEO MENU settings do not remain in memory.
34
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P34-35 A-V Menu).p65
34 2002/04/16, 13:43
Video / Audio Adjustment
Video Adjustment
1
Press ACTION to display MAIN
MENU.
2
3
4
DVD
TV
M A I N MENU
LOCK
CLOCK
LANGUAGE
1
3
5
CH
SELECT : SET : SET
END : ACT I ON
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
SET UP V I DEO / AUD I O
V I DEO MENU : NORMAL
V I DEO ADJUST
AUD I O MENU : MUS I C
AUD I O ADJUST
SELECT :
SET : SET
END : ACT I ON
V I DEO ADJUST
5
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
STANDARD
SELECT :
ADJUST :
END : ACT I ON
1) Press to select “TV.”
2) Press SET to display SET UP
TV screen.
1) Press to select “SET UP
VIDEO/AUDIO.”
2) Press SET to display.
1) Press to select “VIDEO
ADJUST.”
2) Press SET to display.
1) Press to select an item.
(See below.)
2) Press to adjust.
To Reset VIDEO Controls.
Press and SET to select and set
“STANDARD.” All controls return to their factory settings.
Audio Adjustment
a
Press ACTION to display MAIN
MENU.
b
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
1) Press to select “TV.”
2) Press SET to display SET UP
TV screen.
TV
SELECT : SET : SET
END : ACT I ON c
SET UP TV
CAPT I ON
I NPUT SELECT : TUNER
SET UP V I DEO / AUD I O
FM ANTENNA : I NT
REMOTE WARN I NG : ON
DVD VOL ADJUST : + 2
SELECT : SET : SET
END : ACT I ON
1) Press to select “SET UP
VIDEO/AUDIO.”
2) Press SET to display.
d
SET UP V I DEO / AUD I O
V I DEO MENU : NORMAL
V I DEO ADJUST
AUD I O MENU : MUS I C
AUD I O ADJUST
1) Press to select “AUDIO
ADJUST.”
2) Press SET to display.
SELECT :
SET : SET
END : ACT I ON e
BASS
TREBLE
AUDIO ADJUST
BALANCE
STANDARD
1) Press to select an item.
(See below.)
2) Press to adjust.
SELECT :
ADJUST :
END : ACT I ON
To Reset AUDIO Controls.
Press and SET to select and set
“STANDARD.” All controls return to their factory settings.
6
Press ACTION four times to end setup.
[VIDEO Adjustment]
■ COLOR Control
Adjust color intensity.
■ TINT Control
Adjust for natural flesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by adjusting both contrast and color level in the proper
■ balance.
■ SHARPNESS Control
Adjust picture sharpness.
f
Press ACTION four times to end setup.
[AUDIO Adjustment]
■ BASS Control
To adjust the intensity of low frequency sound.
■ TREBLE Control
To adjust the intensity of high frequency
■ sound.
■ BALANCE Control
To adjust the (L/R) unit speaker output level.
• The levels set here do not affect other audio equipment when connected to the
Audio Output L/R Connector.
35
20_27DF62 (P34-35 A-V Menu).p65
35 2002/04/16, 13:43
Disc Operation
Subtitle Language (DVD only)
You can select a different subtitle language
(if offered) than the one set at the Settings for DVD
Operation. (See page 46.)
1
Press SUB TITLE* in Play mode to display the subtitle selection on-screen.
• Display disappears after 5 seconds.
• When no subtitles are offered,
“-” will be displayed instead of the language number.
Ready Checklist
Please read “Basic DVD Operation” on page 16.
[Subtitle language (No.)]
[Audio soundtrack language (No.)]
ENG
FRA
DEU
ITA
ESP
NLD
English
French
German
Italian
Spanish
2
Te amo
1) Press to select desired language.
2) Press (or ) to set.
3) Press (or ) to select “ON” or “OFF.”
Number of subtitle language being played back.
SVE
NOR
DAN
POR
RUS
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
Notes
• When closed captioning is used along with subtitles, they may overlap. If so, turn one function off. (See pages 20 and 21.)
• If after several presses of the button the language does not change, language selection is not offered on the disc.
• Subtitles may not change to the selected language immediately.
• When power is turned on again or disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.
JPN
CHI
KOR
MAL
VIE
Japanese
Chinese
Korean
Malay
Vietnamese
Audio Soundtrack Language (DVD only)
You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See page 46.)
(This operation works only with discs on which multiple audio soundtrack languages are recorded.) a
AUD I O : 1 ENG
D o l b y D i g i t a l 3 / 2 . 1 c h
Hello
Press AUDIO in Play mode to display the audio selection on-screen.
• Display disappears after 5 seconds.
THA
∗
Thai
Other
• Change the No. by pressing , and press SET.
[Audio attribute 1 type, sampling frequency, bit No. of the disc
(see page 47)
]
LPCM
Dolby Digital dts
96KHz or
48KHz
16bit
20bit
24bit
1ch - 5.1ch
1ch - 5.1ch
Linear PCM disc
Dolby Digital disc dts disc
b
SELECT :
Hola
SET : SET
AUD I O : 3 ESP
D o l b y D i g i t a l 3 / 2 . 1 c h
Audio attribute 1 type, sampling frequency, bit No. of the disc.
1) Press to select desired language.
Notes
• If, after several presses of the AUDIO button the language does not change, language selection is not offered on the disc.
SELECT : SET : SET
Number of the audio soundtrack language being played back.
• When power is turned on again or disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P36-43)Disc OP.p65
36 2002/04/16, 13:43
*Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
When
appears on the screen while a button is being pushed, it means that the corresponding operation is prohibited by the unit or the disc.
Multiple Angle Viewing (DVD only)
DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.
1
Press ANGLE in Play mode to display the angle selection on-screen.
• Display disappears after 5 seconds.
ANGLE Indicator
Notes
• ANGLE Indicator lights up on the unit when a scene recorded at different angles is detected.
• The angle number can be set beforehand so that the angle is switched whenever ANGLE
Indicator lights up.
2
1) Press to select the desired angle.
Number of angle being played back.
ADD/DLT
AUDIO
SUBTITLE
Vocal selection for Karaoke discs (DVD/Video CD)
a
Press AUDIO in Play mode to display the audio screen.
b 1) Press (or ) to select as shown below.
2) Press (or ) to set.
(DVD only)
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
ANGLE
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
SELECT
SET
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1 + V2 VOCAL V1 VOCAL V2 VOCAL OFF
• Video CD LR L R
ZOOM
Notes
• Closed captioning will not be displayed while Picture Zoom is used. To see subtitles, set the subtitle feature to ON (see page 36).
• The subtitle cannot be enlarged nor can it’s position be changed.
• The picture zoom feature does not work with a Video CD.
• During picture zoom, “ZOOM1” or
“ZOOM2” is displayed on-screen.
• Zooming, on some discs, may result in poor picture quality, or may not operate at all.
Picture Zoom (DVD only)
You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button on the remote during DVD playback.
Set Zoom size.
Press ZOOM repeatedly to change display as follows.
• You can enlarge the center portion of the image to one of 2 magnifications.
X 1.0 (ORIGINAL) X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)
Hello!
1st press 2nd press
3rd press
■ Use the , , and buttons to move the position up, down, left and right.
37
20_27DF62 (P36-43)Disc OP.p65
37 2002/04/16, 13:43
Disc Operation (continued)
Title menu (DVD only)
Some DVDs have more than one title, e.g.
movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)
1
T I TLE MENU
Dogs
Love r s
Cas t l es
B i r ds
<Example>
Press TITLE* in
Play mode to display title screen.
• Pressing TITLE again resumes play from the scene when TITLE was first pressed.
2
T I TLE MENU
Dogs Cas t l es
Love r s B i r ds
B i rds
of the world
1) Press or
number Key(s)
to select a title.
2) Press SET or
PLAY to start play.
• Step 2) not necessary when using number key(s).
<Example>
DVD menu (DVD only)
DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc. Although contents and operation may vary, the following steps show basic steps for using the menu.
a
DVD MENU
1 . SUBT I TLE
Press MENU in Play mode to display DVD menu.
2 . AUD I O
3 . ANGLE
<Example>
• Pressing MENU again resumes play from the scene when MENU was first pressed.
OPEN/CLOSE LIGHT
N
U
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL VOL
+
CH
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION
SKIP PLAY
RETURN
SKIP
+
PAUSE STOP
SLOW/SEARCH
ZOOM
NUMBER keys
TITLE
CLEAR
DISPLAY
MENU
SELECT
SET
ACTION
PLAY
STOP b
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
<Example>
Repeat step “b” if there is more than one menu.
1) Press or
number key(s)
to select an item.
2) Press SET or
PLAY to access.
• Step 2) not necessary when using number key(s).
38
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P36-43)Disc OP.p65
38 2002/04/16, 13:43
*Important:
If a remote control button does not work when pressed, press the FM/TV, DVD button on the remote and try the button again.
Program Play (Video CD/CD)
You can program specific tracks and order of play.
1
Press ACTION in Stop mode to display
MAIN MENU.
2
M A I N MENU
1) Press to select “DVD.”
2) Press SET to DVD LOCK LANGUAGE
5
3
1
display screen.
TV CLOCK CH
SELECT : SET : SET
END : ACT I ON
DVD MAIN MENU
3 1) Press to select
“PLAY MODE.”
2) Press SET to display screen.
SELECT
SET
END
:
: SET
: ACT I ON
PLAY MODE
4
1) Press to select
“PROGRAM PLAY.”
2) Press SET to display screen.
SELECT
SET
END
:
: SET
: ACT I ON
5
1
2
3
PROGRAM PLAY
D I SC
6 11 16
7 12 17
8 13 18
4 9 14 19
5 10 15 20
CLEAR LAST
CLEAR ALL
SELECT :
PROGRAM
5
15
1 13
3
2
8
6
2
START
SET
END
: SET
: ACT I ON
1) Press to select a track number.
(Track numbers on disc are displayed.)
2) Press SET to set.
• Repeat step 5 to select another track.
• The selected track is added on the right side.
6
PROGRAM PLAY
D I SC
1
2
6 11 16
7 12 17
3 8 13 18
4 9 14 19
5 10 15 20
CLEAR LAST
CLEAR ALL
SELECT
SET
END
:
: SET
: ACT I ON
PROGRAM
5
15
1 13
3
2
8
6
2
START
1) Press to select “START.”
2) Press SET to start play of programs in the sequence selected.
• To cancel, press STOP during play, then press
CLEAR.
Notes
• Up to 15 tracks can be programmed.
• “ ” or “ ” (depending on disc) indicates additional
PROGRAM PLAY screen. Press previous screen.
for next or
• To clear the last program one by one,
Press
to move to “CLEAR LAST” and press
SET. (Pressing CLEAR also clears last program.)
• To clear all programs,
Press
to move to “CLEAR ALL” and press
SET. (Programs are also cleared when the power is turned off or the disc is removed.)
Program Repeat Play
(Video CD/CD)
a
Do steps 1 through 6 on this page.
b
Press DISPLAY to display
Disc Information screen.
(Disc Information Screen)
TRACK : 1
PBC : OFF
V I DEO CD
1 : 35 : 12
SET : SET NEXT : D I SPLAY c
Press DISPLAY again to display Unit Information screen.
d Press SET to enter Select mode.
(“REPEAT OFF” will flash.)
(Unit Information Screen)
SET : SET END : D I SPLAY e
Press to select “DISC
REPEAT.”
(Unit Information Screen)
PLAY
DISC REPEAT
PROGRAM PLAY f
Ready Checklist
Unit is in TV mode, press FM/TV.
Video CD or CD is inserted.
SELECT :
SET : SET END : D I SPLAY
Press SET to set mode. (“DISC
REPEAT” stops flashing.)
To cancel, select “REPEAT OFF” in step e, then press SET.
39
20_27DF62 (P36-43)Disc OP.p65
39 2002/04/16, 13:43
Disc Operation ( continued
)
Random Play (Video CD/CD)
Tracks are played in a random order.
1
Press ACTION* in Stop mode to display
MAIN MENU.
*Important:
If a remote control button does not work when pressed, press the FM/TV button on the remote and try the button again.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
1) Press to select “DVD.”
2) Press SET to display screen.
OPEN/CLOSE LIGHT
N
U
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
3
DVD MAIN MENU
1) Press to select
“PLAY MODE.”
2) Press SET to display screen.
4
SELECT
SET
END
:
: SET
: ACT I ON
PLAY MODE
SELECT
SET
END
:
: SET
: ACT I ON
1) Press to select
“RANDOM PLAY.”
2) Press SET to begin random play
.
• To cancel, press STOP during play, then press
CLEAR.
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
RETURN
SKIP
+
ZOOM
CLEAR
SELECT
SET
ACTION
STOP
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P36-43)Disc OP.p65
40 2002/04/16, 13:43
DVD Operation using On-Screen Displays
When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and unit information (repeat play, Play mode).
1
Press DISPLAY in Play or Stop mode to display “On-Screen Display.”
• Each press of DISPLAY changes the on-screen display as follows. (Please refer to page 42 or 43.)
Selected disc information
Selected unit information
Normal Screen
Note
•
DISPLAY button does not function while DVD
TITLE MENU is displayed.
2
1) Press (or ) to select an item.
2) Press SET to set.
1) Press to select the setting.
2) Press SET to set.
<Example of DVD>
T I TLE : 12
CHAPTER : 11
T I TLE : 12
CHAPTER : 24
SELECT :
SET : SET
DVD
0 : 12 : 34
DVD
0 : 12 : 34
NEXT : D I SPLAY
• For some functions the setting will be registered immediately without pressing SET.
• When numbers are displayed (e.g. title number), the NUMBER keys are also available.
SELECT :
SET : SET NEXT : D I SPLAY
<Example of Video CD>
TRACK
PBC
: 12
: OFF
V I DEO CD
0 : 12 : 34
SET
TRACK : 17
PBC : OFF
: SET
V I DEO CD
0 : 12 : 34
NEXT : D I SPLAY
To make corrections, press
and SET repeatedly to move to error, then correct.
• Pressing is effective for elapsing time instead of the above buttons. Press repeatedly to delete the error, then correct.
To return to the normal screen,
press CLEAR or
DISPLAY repeatedly.
SET : SET NEXT : D I SPLAY
Ready Checklist
Unit is in DVD mode, press DVD.
OPEN/CLOSE LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
DSS
CABLE
TIME
R
CH
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP PLAY SKIP
+
PAUSE STOP
SLOW/SEARCH
ZOOM
NUMBER keys
CLEAR
DISPLAY
SELECT
SET
Notes
• When DISPLAY is pressed during playback of a Video CD with Playback control, the
NUMBER keys are not available on the displayed screen. In this case, press DISPLAY again to remove the displayed screen.
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by the unit or the disc.
41
20_27DF62 (P36-43)Disc OP.p65
41 2002/04/16, 13:43
DVD Operation using On-Screen Displays (continued)
Detailed Descriptions of Each On-Screen Display
Disc information screen (for DVD)
1. TITLE No.
• Change the No. by pressing
keys, and press SET.
2. Chapter No.
• Change the No. by pressing
keys, and press SET.
* or the NUMBER
or the NUMBER
3. Disc currently being played
4. Elapsed playing time
The screen may be changed by selecting the elapsed time.
• Change the elapsed time by pressing NUMBER
keys, and press SET.
(e.g.) 01 : 23 : 45 0
➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5
• This function does not work with some discs.
1
2
T I TLE : 1
CHAPTER : 12
SELECT :
SET : SET
DVD
1 : 12 : 55
3
4
NEXT : D I SPLAY
Disc information screen (for Video CD/ CD)
A. Track No.
• Change the No. by pressing
keys, and press SET.
or the NUMBER
B. Playback control ON/OFF
[Video CD with playback control only]
A
B
ON Video CD menu play is displayed.
OFF Video CD menu play is cleared.
C. Disc currently being played
Video CD CD
D. Elapsed playing time
TRACK : 1
PBC : OFF
SET : SET
OPEN/CLOSE
LIGHT
V I DEO CD
1 : 35 : 12
NEXT : D I SPLAY
U
N
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
Notes
• Track No. and elapsed playing time are not displayed during play started from menu of Video
CDs with playback control.
• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by the unit or the disc.
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
C
D
NUMBER keys
SELECT
SET
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P36-43)Disc OP.p65
42 2002/04/16, 13:43
*Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Detailed Descriptions of Each On-Screen Display
Unit information screen
• Change the desired mode during play by pressing , and press SET.
a. Repeat Play
DVD
Video CD/CD
CHAPTER REPEAT
TRACK REPEAT
TITLE REPEAT
DISC REPEAT
REPEAT OFF
REPEAT OFF a
PLAY
CHAPTER REPEAT
SELECT :
SET : SET END : D I SPLAY
b. Play mode [Video CD/ CD only]
(See page 39 or 40.)
PROGRAM PLAY
RANDOM PLAY
-----
program play
random play
normal play b
PLAY
D I SC REPEAT
RANDOM PLAY
SET : SET END : D I SPLAY
For your reference
• CHAPTER/TITLE REPEAT PLAY (DVD)
CURRENT PLAYBACK POSITION
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
TITLE chapter chapter chapter
• TRACK/DISC REPEAT PLAY (Video CD/CD)
CURRENT PLAYBACK POSITION
TRACK REPEAT
DISK REPEAT
NORMAL PLAY track track track
43
20_27DF62 (P36-43)Disc OP.p65
43 2002/04/16, 13:43
MP3 Playback Operation
MP3 Playback
You can use this unit to play MP3 format audio recorded for personal use with a computer etc. onto a CD-R or CD-RW.
Play may not be possible in some cases due to the condition of the recording.
1
Press POWER* on the remote or unit.
2
Press OPEN/CLOSE,
and then place a MP3 disc into the disc tray.
Press OPEN/CLOSE to close.
3
MP3 MENU is displayed and playback is started automatically.
(The MP3 CD directory is displayed.)
■ MP3 playback (During STOP mode)
1) Press to select an MP3 file (
)
.
2) Press SET or PLAY to start playback.
■ Select folder (During STOP mode)
1) Press to select a folder ( ).
2) Press SET to display files/folders contained in the folder.
■ Select parent folder (During STOP mode)
1) Press to select a folder ( ).
2) Press SET to make changes to the previous directory display.
Function
Status
Folder area
(The currently displayed folder turns green)
<Example>
ROOT
<Example>
PLAY
MP3 MENU
00 : 00 : 00
ROOT . .
VA END_WALTZ
TECHNO DD_CUB I C
POPS NOCTURNE
JAZZ NORN
PLAY MODE : NORMAL
PLAY MODE
Counter
Parent folder
File area
(The selected
MP3 file/folder is displayed with a cursor.)
Note
• Folder area operation cannot be done.
Only file area operation is possible.
■ Select PLAY MODE (During STOP mode)
1) Press to move cursor to
PLAY MODE.
2) Press to select the desired
PLAY MODE (see below).
VA
JAZZ
END_WALTZ
DD_CUB I C
NOCTURNE
NORN
TECHNO
POPS
: MP3 file
: Folder
: Parent folder
(The MP3 CD directory structure displayed in the above example OSD is shown in the diagram at left.)
■ Forward/Reverse Search
Press FF/SLOW+ or REW/SLOW- during play.
Press PLAY to release.
• Search speed, slow at first, increases with each additional press of the button up to 4 levels.
■ Forward/Reverse Track Skip
Press SKIP | or | SKIP during play.
Each press skips a track.
• If pressed within first 3 seconds of playback, skips to the previous track. If over 3 seconds, returns to first track. (| SKIP only.)
• Only the SKIP | or | SKIP button can be used for track skip selection during playback.
Put unit in Stop mode before performing folder/file selection (see above right.)
[PLAY MODE]
NORMAL:
All MP3 files are selected and played back one time only.
SINGLE REPEAT:
The selected MP3 file is played back repeatedly.
FOLDER REPEAT:
The MP3 files contained in the selected folder are played back repeatedly.
However, folders below the selected folder are not played back.
DISC REPEAT:
All MP3 files are played back repeatedly.
4
Press STOP to stop playing.
5
Press OPEN/CLOSE to eject the disc.
The MP3 MENU is closed automatically.
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P44-45 DVD).p65
44 2002/04/16, 13:43
DVD Lock Feature
*Important:
If a remote control button does not work when pressed, press the FM/TV, DVD button on the remote and try the button again.
You can prevent playback of DVDs with a specific rating level which may be unsuitable for children.
• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited.
Caution
Discs not encoded with a rating level will play even if the jacket states it is for mature audiences. For these discs, the DVD Lock Ratings will not work.
DVD Lock Ratings (DVD only)
Perform DVD Lock setting in TV mode.
Enter your secret code to display LOCK menu.
(Perform “Enter Secret Code” steps on page 30.)
1
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
➛
➛
1) Press to select
“DVD LOCK.”
2) Press SET to set
“ON” or “OFF.”
2
LOCK
US MOV I ES : OFF
CHANGE SETT I NGS
US TV PROGRAMS : OFF
CHANGE SETT I NGS
DVD LOCK : OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT : SET : SET
END : ACT I ON
1) Press to select
“CHANGE
SETTINGS.”
2) Press SET to display screen.
3
3
4
1
2
UNLOCKED
5
6
7
8
LOCK ALL
SELECT : SET : SET
END : ACT I ON
1) Press to select rating level.
2) Press SET to select
“LOCKED” or
“UNLOCKED.”
LEVEL 1 : LOCK ALL:
Playback of all DVDs, CDs and Video CDs is prohibited. (Use to prohibit play of mature theme DVDs not encoded with a rating level.)
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 :
DVDs for general audiences/children can be played back. (DVDs with mature content are prohibited.)
LEVEL 8 : NO LIMIT: (Factory preset)
All DVDs can be played back.
• Ratings which are highlighted in Green will be blocked; those not highlighted (white letters) will not be blocked.
4
Press ACTION three times to end setup.
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION RETURN
SKIP
PAUSE
PLAY
STOP
SLOW/SEARCH
SKIP
+
ZOOM
SELECT
SET
ACTION
<When DVD Lock is activated>
PLAYER S RAT I NG L I M I T.
DO YOU WANT TO CHANGE THE
L I M I T?
YES
NO
SELECT :
SET : SET END : D I SPLAY
After DVD Lock is set and a blocked DVD is played, this message will appear. The message may differ depending on the disc.
To continue viewing a blocked program for now,
Press to select “YES” and
SET. Then, enter your 4-digit secret code. When “NO” is selected, blocked programs cannot be viewed.
To change DVD LOCK settings
After entering your secret code in step 3 on page 30, select “OFF” to deactivate DVD Lock or change the rating level.
45
20_27DF62 (P44-45 DVD).p65
45 2002/04/16, 13:43
Settings for DVD Operation
1
Press ACTION* in Stop mode to display
MAIN MENU.
2
M A I N MENU
DVD LOCK
CLOCK
LANGUAGE
1
3
5
CH TV
SELECT : SET : SET
END : ACT I ON
1) Press to select “DVD.”
2) Press SET to display screen.
Once initial settings are done, they remain in memory (even after the power is off) until changed.
This means the unit will always operate under the same conditions
(especially DVDs) each time.
Ready Checklist
Unit is in TV mode, press FM/TV.
3
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: L e t t e r b o x
1) Press to select an item.
2) Press SET to set.
SELECT
SET
END
:
: SET
: ACT I ON
DISC LANGUAGES (See below.)
Any languages offered on the disc can be set. If a language not offered is set, the original disc language will be selected.
AUDIO OUTPUT (See page 47.)
You can set the audio output that comes from the digital audio output terminal.
STILL MODE (See page 48.)
To select “FIELD” or “FRAME” to prevent jitter or to make small text or fine patterns clearly visible in a still picture. When
“AUTO” is set, “FIELD” or “FRAME” is selected automatically.
TV MODE (See page 48.)
To select whether the video material for a wide-screen will be played back in Pan & Scan style or in Letterbox style.
4
5
DISC LANGUAGES (DVD only)
To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: AUTO
: L e t t e r b o x
SELECT
SET
END
AUD I O
SUBT I TLE
MENUS
SELECT
SET
END
DVD MAIN MENU
:
: SET
: ACT I ON
D I SC LANGUAGES
: E n g l i s h
: AUTO
: E n g l i s h
:
: SET
: ACT I ON
1) Press to select
“DISC LANGUAGES.”
2) Press SET to display screen.
1) Press to select an item.
2) Press SET repeatedly for desired language.
(Please refer right.)
“AUDIO” selections
To select the audio soundtrack language.
(factory preset: English)
English/Spanish/French/Japanese
Original: Original disc language
OTHER
✱✱✱✱: Other language selection*
1
“SUBTITLE” selections
To select the subtitle language.
(Factory preset: AUTO)
AUTO: Same language selected for
“AUDIO”
• If language set for “AUDIO” is used in playback, subtitles will not appear.
• If another language is used during playback, the subtitles will appear in the language selected at “AUDIO” setup.
English/Spanish/French/Japanese
OTHER
✱✱✱✱: Other language selection*
1
“MENUS” selections
(factory preset: English)
To select the language used in title menus or DVD menus.
English/Spanish/French/Japanese
OTHER
✱✱✱✱: Other language selection*
1
To enter OTHER
✱✱✱✱ code number,
Press number keys (Please refer to language codes on page 49).
To make corrections, press repeatedly to delete language code number, and correct.
6
Press ACTION to redisplay DVD menu and go to step 3 to setup another item.
Or, press ACTION three times to exit.
* 1 If the selected language is not offered, the original disc language is selected.
46
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
2002/04/16, 13:43 20_27DF62 (P46-49 Setting DVD).p65
46
*Important:
If a remote control button does not work when pressed, press the FM/TV, DVD button on the remote and try the button again.
Select the digital output to be output from the optical digital audio output connector of the unit.
1
2
AUDIO OUTPUT
Do steps 1 and 2 on page 46.
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: F I ELD
: L e t t e r b o x
SELECT
SET
END
:
: SET
: ACT I ON
1) Press to select
“AUDIO OUTPUT.”
2) Press SET to display screen.
Recommended setting
Type of amplifier
to be connected
No amplifier is connected
AV amplifier (with digital audio input connector) without Dolby Digital/dts decoder
AV amplifier including
Dolby Digital decoder
AV amplifier including
Dolby Digital/dts decoder
LPCM
(DVD)
OFF
PCM*
1
Dolby
Digital
OFF
OFF*
2
PCM*
1
Bitstream
PCM*
1
Bitstream dts
OFF
OFF*
OFF
2
*
3
3
■
OFF: Linear PCM of less than 48 kHz/16 bit is output.
When playing DVDs recorded in linear PCM of over 48 kHz/20 bit or 96 kHz, no digital audio is output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or 96 kHz, digital audio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
■
Bitstream:
Dolby Digital bitstream (1ch-5.1ch) is
OFF:
output. (Factory preset)
No output.
■
Bitstream:
dts bitstream is output. (Factory preset)
OFF:
No output.
■
OFF: Normal audio range is selected. (Factory preset)
ON:
For dynamic sound even at low volume, this is useful for late-night listening. [Dolby Digital DVDs
■ only].
■ “SURROUND” selections
Surround Sound creates the effect of sound coming from non-existent rear speakers even when only connected to a 2-channel stereo system.
OFF: No Surround Sound effect. (Factory preset)
ON:
Surround Sound effect.
4
AUD I O OUTPUT
LPCM(DVD)
D o l b y D i g i t a l d t s
DRC
SURROUND
: OFF
: B i t s t r e a m
: OFF
: OFF
: OFF
SELECT
SET
END
:
: SET
: ACT I ON
1) Press to select an item.
2) Press SET repeatedly for output.
(See below.)
Press ACTION to redisplay DVD menu and go to step 2 to setup another item.
Or, press ACTION three times to exit.
• Make settings according to amplifier connected to optical audio output as shown in above table.
• When a dts decoder is not connected, to enjoy dts DVD, please select audio output other than dts on the dts DVD menu screen. Otherwise, there will be no sound from the unit speakers.
*1 Audio output from unit is converted to 48 kHz/16 bit in addition to audio from digital audio output.
To enjoy high quality sound at 48 kHz/
20 bit /24 bit or 96 kHz, connect the amplifier or decoder directly to the audio output connectors, not to the digital audio output connector. [Select “OFF” at the “LPCM (DVD)”.]
*2 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “OFF”.
If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.
*3 When a dts decoder is connected, please select “Bitstream” in “dts”.
If “OFF” is selected, there will be no sound.
Notes
• Turn off other surround effects when using this surround effect.
• For optimum effect, the distance between the unit and the listener should be about
3 or 4 times the distance between the right and left front speakers.
47
2002/04/16, 13:43 20_27DF62 (P46-49 Setting DVD).p65
47
Settings for DVD Operation (continued)
STILL MODE
Set to reduce jitter in a displayed still picture or a motion picture.
1
Do steps 1 and 2 on page 46.
2
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: F I ELD
: L e t t e r b o x
SELECT
SET
END
:
: SET
: ACT I ON
1) Press * to select
“STILL MODE.”
2) Press SET repeatedly for mode.
(See below)
AUTO:
“FIELD” (Field still) or “FRAME” (Frame still) is automatically selected during the still mode.
(Factory preset)
FIELD:
“FIELD” (Field still) is always selected.
This setting will reduce jitter when compared with “AUTO” on some discs.
FRAME: “FRAME” (Frame still) is always selected.
Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.
3
Press ACTION twice to exit this mode.
*Important:
If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
OPEN/CLOSE
LIGHT
U
N
D
FM/TV
MU
TE
D V D
10
CH
DSS
CABLE
TIME
R
VOL
CH
VOL
+
R
-T
U
N
ADD/DLT
AUDIO ANGLE SUB TITLE DISPLAY
TITLE MENU
S E T
ACTION
SKIP PLAY
RETURN
SKIP
+
PAUSE STOP
SLOW/SEARCH
ZOOM
SELECT
SET
ACTION
Selecting TV MODE
Set the screen display style for widescreen video material playback.
a
Do steps 1 and 2 on page 46.
b
DVD MAIN MENU
D I SC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
TV MODE
: F I LED
: L e t t e r b o x
SELECT
SET
END
:
: SET
: ACT I ON
1) Press to select
“TV MODE.”
2) Press SET repeatedly for mode.
(See below.)
Example
• Pan & Scan (Factory preset)
Pan & Scan :
Widescreen video data is played in Pan
(Factory preset) & Scan style (left and right of screen is trimmed.)
• Video data not formatted in Pan & Scan will play in letterbox style.
Letterbox :
Widescreen video data is played in
Letterbox style (top and bottom of screen has black margin).
• Letterbox c
Press ACTION twice to exit this mode.
48
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
2002/04/16, 13:43 20_27DF62 (P46-49 Setting DVD).p65
48
Language Code List
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/ or “MENUS” (see page 46).
Code Language
6565
Afar
6566
Abkhazian
6570
Afrikaans
6577
Ameharic
6582
Arabic
6583
Assamese
6588
Aymara
6590
Azerbaijani
6665
Bashkir
6669
Byelorussian
6671
Bulgarian
6672
Bihari
6678
Bengali; Bangla
6679
Tibetan
6682
Breton
6765
Catalan
6779
Corsican
6783
Czech
6789
Welsh
6865
Danish
6869
German
6890
Bhutani
6976
Greek
6978
English
6979
Esperanto
6983
Spanish
6984
Estonian
6985
Basque
7065
Persian
7073
Finnish
7074
Fiji
Code Language
7079
Faroese
7082
French
7089
Frisian
7165
Irish
7168
Scots Gaelic
7176
Galician
7178
Guarani
7185
Gujarati
7265
Hausa
7273
Hindi
7282
Croatian
7285
Hungarian
7289
Armenian
7365
Interlingua
7378
Indonesian
7383
Icelandic
7384
Italian
7387
Hebrew
7465
Japanese
7473
Yiddish
7487
Javanese
7565
Georgian
7575
Kazakh
7576
Greenlandic
7577
Cambodian
7578
Kannada
7579
Korean
7583
Kashmiri
7585
Kurdish
7589
Kirghiz
7665
Latin
Code Language
7678
Lingala
7679
Laothian
7684
Lithuanian
7686
Latvian, Lettish
7771
Malagasy
7773
Maori
7775
Macedonian
7776
Malayalam
7778
Mongolian
7779
Moldavian
7782
Marathi
7783
Malay
7784
Maltese
7789
Burmese
7865
Nauru
7869
Nepali
7876
Dutch
7879
Norwegian
7982
Oriya
8065
Panjabi
8076
Polish
8083
Pashto, Pushto
8084
Portuguese
8185
Quechua
8277
Rhaeto-Romance
8279
Romanian
8285
Russian
8365
Sanskrit
8368
Sindhi
8372
Serbo-Croatian
8373
Singhalese
Code Language
8375
Slovak
8376
Slovenian
8377
Samoan
8378
Shona
8379
Somali
8381
Albanian
8382
Serbian
8385
Sundanese
8386
Swedish
8387
Swahili
8465
Tamil
8469
Telugu
8471
Tajik
8472
Thai
8473
Tigrinya
8475
Turkmen
8476
Tagalog
8479
Tonga
8482
Turkish
8484
Tatar
8487
Twi
8575
Ukrainian
8582
Urdu
8590
Uzbek
8673
Vietnamese
8679
Volapük
8779
Wolof
8872
Xhosa
8979
Yoruba
9072
Chinese
9085
Zulu
49
2002/04/16, 13:43 20_27DF62 (P46-49 Setting DVD).p65
49
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
No power…
Power turns itself off...
Correction
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
• Auto power-off (shutoff) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in
TV mode. Turn the power back on. (P. 17, 28)
Monitor
No picture or sound...
Poor picture with normal sound...
Poor sound with normal picture...
Poor TV reception...
No color or poor color...
Ghost (multiple) images...
TV programs cannot be watched...
Correction
• Make sure your antenna system (TV or CABLE), is correctly set. (P. 10)
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
• Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP Video Adjustment. (P. 35)
• Adjust VOLUME control. (P. 18)
• Adjust SHARPNESS and PICTURE controls in the SET UP
Video Adjustment. (P. 35)
• Adjust TINT and COLOR controls in the SET UP Video
Adjustment. (P. 35)
• Install a directional antenna.
• Make sure the selected channel is in unit’s memory. (P. 12)
Remote Control
Unit cannot be controlled...
ACTION, SELECT, SET, POWER, etc. buttons cannot be selected...
Correction
• Aim Remote directly at the remote sensor on the unit. (P. 9)
• Avoid any object blocking signal path.
• Inspect the remote batteries. (P. 4)
• Exposing unit remote sensor to direct fluorescent or outdoor light may cause signal interference.
• Press FM/TV for TV mode. (P. 26)
• Press
DVD for DVD mode. (P. 26)
• Press
FM/TV for FM mode. (P. 26)
• Check remote batteries.
If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262.)
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262.) or send e-mail to : [email protected]
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P50-51 Before Req.).p65
50 2002/04/16, 13:43
DVD/Video CD/CD
Play fails to start even when
PLAY is pressed...
Play starts but then stops immediately...
Picture is distorted during rapid advance or rapid reverse...
No Forward/Reverse search play...
Play does not start even when title is selected...
Audio soundtrack and/or subtitle language is not the one selected at the initial settings...
No subtitles...
Correction
• This unit cannot play discs other than DVDs, Video CDs and CDs.
• The disc may be dirty and require cleaning.
• Be sure disc is installed with label side up.
• The picture will be somewhat distorted at times: this is normal.
• Some discs may have sections which prohibit Forward/Reverse search. (P. 17)
• Confirm the “DVD LOCK” setting. (P. 45)
• If the audio soundtrack and/or subtitle language selected at DVD initial settings does not exist on the disc, it will not be accessible.
Alternative audio soundtrack
(or subtitle) language cannot be selected...
Angle cannot be changed...
Miscellaneous
The disc cannot be removed...
• Subtitles appear only when available on disc.
• Select “ON” at the “Changing subtitle language” section (P. 36) to display subtitles.
• Alternative language cannot be selected with discs which do not contain more than one language.
• For some discs, alternative language cannot be selected with the
AUDIO or SUB TITLE button. Try selecting it from the DVD menu if available.
• This function is dependent on software availability. Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE Indicator on unit lights up). (P. 37)
Correction
• First, unplug unit. Then, prepare a rigid wire (e.g. an extended paper clip, etc.) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little.
Now, pull the tray all the way out and remove the disc. (P. 6)
Warning and Instruction Displays
These displays will alert you of a missed operation or provide further instructions.
OSD
PLEASE SET CLOCK
BEFORE TIMER SETTING
PLEASE CHECK THE DISC, AND FOR
STAINS OR SCRATCHES ON DISC
Caution
• If you attempt to set the On-Timer and the Clock is not set...
• If you press PLAY, or the unit reads data from a stained or scratched disc in DVD mode. Also, if the type of disc is other than DVD, Video CD or CD...
Page
12
7
51
20_27DF62 (P50-51 Before Req.).p65
51 2002/04/16, 13:43
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Product
Camcorder
DVD/VCR Deck,
A/V Mixer
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
TV/HDR
Combination
Parts
One (1) Year (except
CCD Image Sensor)
CCD Image Sensor
- 6 (Six) Months
One (1) Year
One (1) Year
(except CRT)
CRT - Two (2) Years
One (1) Year
(except CRT)
CRT - Two (2) Years
Rechargeable
Batteries
(in exchange for defective item)
Tape
(in exchange for defective item)
Memory Cards
(in exchange for defective item)
Ten (10) Days
Five (5) Days
Ninety (90) Days
Labor
Ninety (90) Days
Ninety (90) Days
Service
Carry-In or Mail-In
Contact Number
1-800-211-PANA(7262)
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Carry-In or Mail-In 1-800-211-PANA(7262)
Carry-In: 21” CRT and Smaller
In-Home or Carry-In:
22” CRT and Larger
1-800-211-PANA(7262)
In-Home or Carry-In 1-888-843-9788
Not Applicable
Not Applicable
Not Applicable
Carry-In or Mail-In
Carry-In or Mail-In
Carry-In or Mail-In
1-800-211-PANA(7262)
1-800-211-PANA(7262)
1-800-211-PANA(7262)
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service, as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized servicer and does not include removal or re-installation of an installed product. It is possible that certain in-home repairs will not be completed in-home, but will require that the product, or parts of the product, be removed for shop diagnosis and/or repair and then returned.
52
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P52-53 Warranty).p65
52 2002/04/16, 13:43
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel, office, restaurant, or other business), rental use of the product, service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or images, data or other memory or recorded content. The items listed are not exclusive, but are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,
ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s
Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE APPLICABLE)
WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY.
Customer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquiries please contact:
1-800-211-PANA (7262)
,
Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail : [email protected]
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
As of February 2002
53
20_27DF62 (P52-53 Warranty).p65
53 2002/04/16, 13:43
Spanish Quick Use Guide
/Guía para rápida consulta
Conecte por favor todas las conexiones del cable o de la antena antes de turing potencia.
Conectando
Para Ant./Cable
Conecte Ant./Cable a la entrada de antena de la TV
(VHF/UHF).
VHF/UHF
Ant./Cable
Unidad
VHF/UHF
Para Sistema Digital de
Satelite (DSS)/Convertidor de cable
Conecte la salida del convertidor de cable la
“VFH/UHF” con el RF cable.
VHF/UHF
Convertidoe de cable
VHF/UHF
Realizando Configuración Inicial
1
Tape el cable electrico de la unidad en el enchufe de pared de la CA.
3
Selecciones se realizaran automaticamente cuando la configuracion termine, la pantalla siguiente aparecera.
2
POWER de la prensa en el telecontrol o la unidad.
La unidad se adelanta y comienzo auto del canal y del reloj.
2 / 6 / 2002 WED 12 : 00PM
DST : ON
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
CH AUTO SET PROCEEDING
Si usa convertidor de cable, enciendala y seleccione el Servicio
Publico de Canales de
Television (PBS) en su horario de uso o tiempo de su zona. Si utiliza receptor DSS este debe de estar apagado.
AUTO CLOCK SET
PROCEEDING
CANCEL : PRESS STOP KEY
Si “AUTO CLOCK SET IS INCOMPLETE” aparece en pantalla, coloque el tiempo usando el procedimiento manual (MANUAL
CLOCK SET). Vea el “Ajuste Manual del
Reloj” en la proxima pagina.
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
54
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
20_27DF62 (P54-61 Spanish).p65
54 2002/04/16, 13:43
Ajuste Manual del Reloj
Si el ajuste automático del reloj no se ha completado, ajuste el reloj manualmente de la siguiente manera.
1
Presione la tecla ACTION en el control remoto para visualizar la pantalla del menú RELOJ.
2
Presione
▲▼ para seleccionar el mes y SET para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST
(Hora de Verano).
3
Presione dos veces la tecla
ACTION para poner el
RELOJ en marcha y salir.
SET CLOCK
SELE CT MONTH
SELECT :
SET : SET
END : ACT I ON
DST : ON
Ajustar de nuevo el reloj
1
Presione ACTION para exhiba el menú.
M A I N MENU
2
DVD LOCK
CLOCK
LANGUAGE
5
3
CH
1
TV
SELECT : SET : SET
END : ACT I ON
Presione
▲▼ para seleccionar “RELOJ”.
Presione SET.
3
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET : SET
END : ACT I ON
Presione
▲▼ para seleccionar “MANUAL” y luego presione SET.
4
SET CLOCK
2 / 6/
:
DST : ON
SELE CT HOUR
SELECT :
SET : SET BACK :
END : ACT I ON
Presione
▲▼ y SET para seleccionar y ajustar la hora y la fecha.
5
Presione ACTION dos veces para que el reloj comience a funcionar y salir desde este modo.
20_27DF62 (P54-61 Spanish).p65
55 2002/04/16, 13:43
55
Spanish Quick Use Guide
/Guía para rápida consulta
Operaciones básicas del DVD
1
Presione POWER en el control remoto o el aparato.
2
Introducir un disco.
1) Presione OPEN/CLOSE.
2) Ponga un disco en la bandeja de disco.
• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada.
1
2
3
Iniciar la reproducción
Presione PLAY.
La bandeja del disco se cierra automáticamente.
• Si está usando un DVD interactivo (Interactive DVD) o un Vídeo CD con contol de reproducción (playback control) y aparece un menú de títulos (TITLE MENU) en la pantalla, siga al paso 5.
4
Elija el artículo deseado.
1) Presione o las teclas numéricas.
2) Presione SET para la reproducción.
Si usa las teclas numéricas, la reproducción comienza automáticamente.
5
Parar la reproducción.
Presione STOP.
6
Expulsar el disco.
Presione OPEN/CLOSE.
■ Para buscar una escena particular
Búsqueda hacia adelante
Presione SLOW en el modo de reproducción.
Búsqueda hacia atrás
Presione SLOW en el modo de reproducción.
(Para liberar, presione PLAY)
■ Para saltar un capítulo o una pista
Salto hacia adelante
Presione SKIP l en el modo de reproducción.
Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla.
Salto hacia atrás
Presione l SKIP en el modo de reproducción.
■ Para ver una imagen fija
Presione PAUSE durante la reproducción.
(Para liberar, presione PLAY)
56
■ Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione PAUSE en el modo de imagen fija.
La imagen avanza un cuadro cada vez que presiona la tecla.
(Para volver a la reproducción normal, presione PLAY.)
■ Para ver en cámara lenta
(DVD/Vídeo CD)
Presione SLOW o SLOW en el modo de imagen fija.
(Para liberar, presione PLAY)
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
20_27DF62 (P54-61 Spanish).p65
56 2002/04/16, 13:43
Cambio del idioma de subtítulos
[DVD solamente]
EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.
1
SUBT I TULO : 1 ENG AC
Presione SUBTITLE durante la reproducción.
• Cuando no haya subtítulos grabados, “-” se visualizará en lugar del número de idioma.
ELE
G IR :
I love you
2
SUBT I TULO : 3 ESP AC
Te amo
Seleccionar el idioma deseado.
1) Presione para seleccionar idioma.
2) Presione (o ) para ajustar.
3) Presione (o ) para seleccionar “ACTIVO” o “INACTIVO.”
Selección de vocal para los discos de Karaoke [DVD/Video CD]
1
Visualizar la pantalla AUDIO.
Presione AUDIO durante la reproducción.
2
SONIDO: 2 ENG VOZ AC
ELE G IR :
Seleccionar el ajuste deseado.
1) Presione (o ) para seleccionar.
2) Presione (o ) para ajustar.
(DVD solamente)
• DVD Karaoke (1 vocal) VOCAL ON
➛
• DVD Karaoke (2 vocales)
VOCAL V1+V2
• Video CD LR
➛
➛
Cambio del idioma de la pista de sonido [DVD solamente]
EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.
1
SON I DO: 1 ENG
D o l b y D i g i t a l 3 / 2 . 1 c h
Hello
Visualizar la pantalla
AUDIO.
Presione AUDIO durante la reproducción.
ELE
G I R :
F I
SET
2
SON I DO: 3 ESP
D o l b y D i g i t a l 3 / 2 . 1 c h
Hola
ELE G IR :
Seleccionar el idioma deseado.
Presione para seleccionar idioma.
Utilización de un menu de
DVD [DVD solamente]
Algunos discos DVD tienen estructuras
únicas de menús llamadas menús DVD.
Por ejemplo, los DVDs programados con un contenido complejo proporcionan menús guía, y los grabados con varios idiomas proporcionan menús para audio e idiomas de subtítulos. Aunque los contenidos de los menús DVD y la operación cambian de disco a disco, a continuación se explica la operación básica cuando se utiliza esta característica.
1
Presione MENU durante la reproducción.
El menú de DVD introducido en el disco se visualiza ahora.
2
DVD MENU
1 . SUBT I TLE
2 . AUD I O
3 . ANGLE
Seleccionar el
ítem deseado.
1) Presione
o las teclas numéricas para seleccionar.
2) Presione SET o
PLAY.
Utilización de un menú de títulos [DVD solamente]
Algunos discos con películas, por ejemplo, vienen con dos o más títulos. Si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.
1
Presione TITLE durante la reproducción.
Ahora se visualiza una lista de los títulos del disco.
2
T I TLE MENU
Dogs Cas t l es
Love r s
B i r ds
Dogs
of the world
Seleccionar el título deseado.
1) Presione o las teclas numéricas seleccionar.
2) Presione SET o PLAY.
57
20_27DF62 (P54-61 Spanish).p65
57 2002/04/16, 13:43
Spanish Quick Use Guide
/Guía para rápida consulta
Visión desde otro ángulo
[DVD solamente]
Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde un número de
ángulos diferentes. Con estos discos, la misma escena podrá verse desde cada uno de estos
ángulos diferentes utilizando el botón ANGLE.
1
Visualizar la pantalla de ángulo.
Presione ANGLE durante la reproducción.
ELEG I R : F I JAR : SET
2
Seleccionar el ángulo deseado.
Presione para seleccionar.
Funcionnamiento del DVD utilizando visualizaciones en pantalla
Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y
ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).
1
Visualizar Visualizaciones en pantalla.
Presione DISPLAY en el modo reproducción o parada.
• Cada vez que se presione DISPLAY, la visualización en pantalla cambia como se muestra a continuación.
Información seleccionada del disco
ELEG I R : F I JAR : SET
Ampliación de la imagen
[DVD solamente]
Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón
ZOOM del control remoto.
Seleccione el tamaño de la imagen.
Presione ZOOM repetidamente para cambiar el tamaño de la imagen como se indica a continuación:
■ Use los botones y para desplazar la posición hacia arriba o hacia abajo.
■ Use los botones y para desplazar la posición hacia la izquierda o hacia la derecha.
2
Selección del ítem deseado
1) Presione (o ) para seleccionar.
2) Presione SET para ajustar
3
<Ejemplo de DVD>
T I TULO : 12
CAP I TULO : 11
DVD
0 : 12 : 34
T I TULO : 12
CAP I TULO : 24
DVD
0 : 12 : 34
ELEG I R :
F I JAR : SET S I GU I ENTE: D I SPLAY
Selección del ajuste deseado
1) Presione para seleccionar.
2) Presione SET para ajustar.
ELEG I R :
F I JAR : SET S I GU I ENTE: D I SPLAY
<Ejemplo de Vídeo CD>
P I STA
PBC
P I STA
PBC
: 12
: I NACT I VO
: 17
: I NACT I VO
V I DEO CD
0 : 12 : 34
V I DEO CD
0 : 12 : 34
Para volver a la pantalla normal,
Presione repetidamente CLEAR o DISPLAY.
F I JAR : SET S I GU I ENTE: D I SPLAY
F I JAR : SET S I GU I ENTE: D I SPLAY
58
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
20_27DF62 (P54-61 Spanish).p65
58 2002/04/16, 13:43
Reproducción programada [Vídeo CD/CD]
Puede usted programar pistas específicas y el orden de reproducción.
• Vídeo CD o CD es insertado en el modeo DVD.
Visualizar MAIN MENU.
1
Presione ACTION en el modo parada.
2
MENU PR I NCIPAL
DVD BLOQUEO
RELOJ
ID I OMA
5
3
1
CANAL TV
ELEG I R : F I JAR : SET
TERM I NAR : ACT I ON
Vísualizar la pantalla DVD.
1) Presione para seleccionar “DVD.”
2) Presione SET para visualizar.
3
DVD MENU PR I NC I PAL
I D I OMAS DEL D I SCO
SAL I DA DE AUD I O
DETENER RASTREO : CAMPO
4 : 3 PREFERENC I A : L e t t e r b o x
MODO DE REPRODUC
ELEG I R
F I JAR
:
: SET
TERM I NAR : ACT I ON
4
MODO DE REPRODUCCION
REPRODUC
CION DE PROGRAMAS
REPRODUCCION ALEATORIA
Seleccionar “MODO DE
REPRODUCCION.”
1) Presione para seleccionar.
2) Presione SET para visualizar.
Seleccionar “REPRODUCCION DE
PROGRAMAS.”
1) Presione para seleccionar.
2) Presione SET para visualizar.
ELEG I R
F I JAR
:
: SET
TERM I NAR : ACT I ON
5
REPRODUCCION DE PROGRAMAS
1
2
3
4
D I SCO
6 11 16
7 12 17
8 13 18
9 14 19
PROGRAMA
5
15
1 13
3
8
6
2
5 10 15 20
BORRAR EL ULT I MO
BORRAR TODO
ELEG I R
F I JAR
:
: SET
TERM I NAR : ACT I ON
2
I N I C I AR
Seleccionar el número de la pista deseada. (Se visualizan los números de la pista del disco).
1) Presione para seleccionar.
2) Presione SET para seleccionar.
• Repita el paso 5 para seleccionar otra pista.
• La pista seleccionada se añade a la parte derecha.
6
REPRODUCCION DE PROGRAMAS
1
2
D I SCO
6 11 16
7 12 17
PROGRAMA
5
15
8
6
3
4
8 13 18
9 14 19
5 10 15 20
BORRAR EL ULT I MO
BORRAR TODO
ELEG I R :
F I JAR : SET
TERM I NAR : ACT I ON
1 13
3 2
2
I N I C I AR
Comenzar “REPRODUCCION DE
PROGRAMAS.”
1) Presione
“INICIAR.”
2) Presione SET.
para seleccionar
• La reproducción comienza en la secuencia programada.
• Para cancelar, pulsar STOP durante la reproducción y luego presione CLEAR.
Reproducción arbitraria [Vídeo CD/CD]
Las pistas se reproducen de forma arbitraria.
1
2
Repita los pasos 1-3 de la página anterior.
MODO DE REPRODUCCION
REPRODUCCION DE PROGRAMAS
REPRODUC CION ALEATO RIA
ELEG I R
F I JAR
:
: SET
TERM I NAR : ACT I ON
Seleccionar “REPRODUCCION
ALEATORIA.”
1) Presione para seleccionar.
2) Presione SET.
• Comienza la reproducción arbitraria.
• Para cancelar, presione STOP durante la reproducción y luego presione CLEAR.
20_27DF62 (P54-61 Spanish).p65
59 2002/04/16, 13:43
59
Spanish Quick Use Guide
/Guía para rápida consulta
Fijaciones iniciales
1
Visualizar MAIN MENU.
Presione ACTION en el modo de parada.
2
Visualizar la pantalla DVD.
1) Presione para seleccionar.
2) Presione SET.
3
Seleccionar el artículo deseado.
1) Presione para seleccionar.
2) Presione SET.
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser ajustados,
Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente del terminal de salida audio digital.
DETENER RASTREO
Para seleccionar “CAMPO” o “CUADRO” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.
4 : 3 PREFERENCIA
Para seleccionar si el material del vídeo para pantalla ancha será vuelto a reproducir en el estilo Pan&Scan o en el estilo
Letterbox en la pantalla.
4
Seleccionar el artículo deseado.
1) Presione para seleccionar.
2) Presione SET.
5
Volver a visualizar el menú de DVD para continuar el ajuste.
Presione ACTION y pase al paso 3 para ajustar otro ajuste o, para salir, presione ACTION tres veces.
Selección de IDIOMAS DEL DISCO
[DVD solamente]
Seleccione “AUDIO”
Inglés / Español / Francés / Japón: (Fijación de fábrica : inglés)
Original : Se seleccionará el idioma original de cada disco.
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “SUBTITULO”
AUTO : Se seleccionará el mismo que fue seleccionado en la preparación de “AUDIO”. (Fijación de fábrica)
• Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán.
• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO”
Inglés / Español / Francés / Japón
OTRO **** : Se puede seleccionar el otro idioma.
Seleccione “MENU”
Inglés / Español / Francés : (Fijación de fábrica : inglés)
OTRO **** : Se puede seleccionar el otro idioma.
60
Por ayuda, llame al 1-800-211-PANA(7262) o envie e-mail : [email protected]
20_27DF62 (P54-61 Spanish).p65
60 2002/04/16, 13:43
Selección de SALIDA DE AUDIO
Seleccione “LPCM(DVD)”
INACTIVO : Por el conector de salida de audio digital solamente sale PCM lineal de
48 kHz/16 bits. Durante la reproducción del DVD grabado en el
PCM lineal de 48 kHz/20 bits o 96 kHz, no sale audio digital. (Fijación de fábrica)
PCM :
Durante la reproducción del DVD grabado en el PCM lineal de 48 kHz/
20 bits/24 bits o 96 kHz, sale audio digital convertido a 48 kHz/16 bits.
(La salida digital de audio PCM está restringida a 48 kHz/16bits o menos para proteger los derechos de autor.)
Seleccione “Dolby Digital”
Bitstream: Sale un flujo de bits Dolby digital
(2ch-5.1ch). (Fijación de fábrica)
INACTIVO : No hay salida de audio.
Seleccione “dts”
Bitstream : Sale un flujo de bits dts. (Fijación de fábrica)
INACTIVO : No hay salida de audio.
Seleccione “DRC (Dynamic Range
Compression)”
INACTIVO : Se selecciona el margen de audio normal.
(Fijación de fábrica)
ACTIVO :
Seleccione este ajuste para disfrutar de un sonido dinámico incluso a bajo volumen. Esto es muy útil para escuchar durante la noche.
[Esta función sólo se activa con
DVDs Dolby Digital.]
Seleccione “SURROUND”
El sonido envolvente crea el efecto de sonido que procede de altavoces que parecen ester en la parte de atrás aún cuando solo se ha conectado a un sistema estéreo de 2 canales.
INACTIVO : No efecto de sonido envolvente.
(Fijación de fábrica)
ACTIVO :
Efecto de sonido envolvente.
Selección de DETENER RASTREO
AUTO :
Durante el modo de imagen fija se seleccionarán automáticamente
“Campo fijo” o “Cuadro fijo” (Fijacion de fabrica)
CAMPO :
Seleccione este ajuste cuando ocurra “distorsión” en las imagenes, incluso cuando se haya seleccionado “AUTO”.
CUADRO : “Cuadro fijo” es siempre seleccionado. Seleccionar este ajuste cuando no se puedan ver claramente texto pequeño o patrones finos incluso cuando esté seleccionado “AUTO”.
Selección de 4 : 3 PREFERENCIA
Pan&Scan : Datos de la pantalla ancha de vídeo son reproducidos en el estilo Pan &
Scan (la parte derecha e izquierda de la pantalla son recortadas).
(Fijación de fábrica)
• Datos de vídeo no formateados en
Pan & Scan serán reproducidos en el estilo letterbox.
Letterbox : Datos de la pantalla ancha de vídeo son reproducidos en el estilo
Letterbox (la parte de arriba y abajo de la pantalla tienen un margen negro).
20_27DF62 (P54-61 Spanish).p65
61 2002/04/16, 13:43
61
Index
T V
A
Accessories .................................................... 4
AC Power Plug ................................................ 9
ACTION button ......................................... 8, 12
ADD / DLT button ...................................... 8, 13
Audio Adjustment .......................................... 35
Audio Auto Gain Control (AGC) .................... 34
AUDIO button ...................................... 8, 19, 25
Audio Connections .................................. 14, 15
Audio Features ....................................... 34, 35
Audio Menu .................................................... 34
Audio Mode for TV Viewing ........................... 19
Audio Mute ..................................................... 18
Audio / Video Input connector (LINE) ............. 9
Audio Output Connector (L/R) ........................ 9
Auto Operation Functions ............................. 28
B
Batteries .......................................................... 4
Before Requesting Service ..................... 50, 51
Before Using .................................................... 4
Blocking Message ......................................... 33
Blue Screen Display ...................................... 23
Broadcast Types .......................................... 19
C
Cable Box Brand Code Number ................... 27
Cable Box Universal Remote Control Feature . 26
Caption On Mute ........................................... 21
Channel ....................................... 10, 12, 13, 23
Channel Caption ........................................... 29
CHANNEL UP / DOWN button ................. 8, 18
Clock ............................................................. 12
Closed Caption ........................................ 20, 21
Code Numbers, DSS / Cable Box Brand ..... 27
Connections .................................................. 10
Connections, Audio ................................. 14, 15
Connections, DSS / Cable Box ..................... 10
Connections, Ant./Cable ............................... 10
Customer Services Directory ...................... 53
D
DISPLAY / ENTER button ................... 8, 23, 26
DSS Brand Code Number ............................ 27
DSS CABLE button ................................... 8, 26
DSS / Cable Box Connections ...................... 10
DST (Daylight Saving Time) ......................... 11
F
FM Radio ................................................ 24, 25
FM/TV button .................................... 8, 24 ~ 26
Front Panel Indicators ..................................... 9
Function Display ........................................... 23
I
Important Safeguards and Precautions ......... 2
Information (Unit, Disc) ............................... 6, 7
Initial Setup .................................................... 10
Indicators on the Front Panel ......................... 9
Input Mode ..................................................... 28
L
Language ................................................. 10, 12
LIGHT button ................................................... 8
Location of Controls .................................... 8, 9
M
MTS Broadcast / TV Stereo System ............ 19
MUTE button ............................................. 8, 18
N
NUMBER keys .......................................... 8, 18
O
100 Key ......................................................... 18
On-Screen Displays (OSD) ......................... 23
ON-TIMER Indicator ................................. 9, 22
ON-TIMER with Alarm .................................. 22
Outdoor Antenna Connections ..................... 10
P
Phones .......................................................... 18
POWER button .......................................... 8, 10
Q
Quality Picture ................................................. 4
R
Rapid Tune .................................................... 18
R-TUNE button ......................................... 8, 18
Remote Control Buttons ................................. 8
Remote Sensor ............................................... 9
Remote Warning Feature ............................. 28
Reset Language, Channels, Clock .............. 12
Reset unit ..................................................... 11
S
Safety Precautions .......................................... 3
Secret Code .................................................. 30
SELECT / SET button ............................... 8, 12
Sleep Timer ................................................... 22
SLEEP TIMER Indicator .......................... 9, 22
Spanish Quick Use Guide .................... 54 ~ 61
Specifications .................................................. 6
SURROUND button .................................. 8, 29
Surround Sound ............................................ 29
S-Video Input connector ................................ 9
T
Table of Contents ............................................ 5
Time Zone Adjust .......................................... 13
TV Operation ................................................. 18
TV Status & Clock Display ........................... 23
TV Timer Features ........................................ 22
U
Unit, Front/Rear view ...................................... 9
Universal Remote Control ............................ 26
US MOVIES Ratings ..................................... 31
US TV PROGRAMS Ratings ........................ 32
V
Video Adjustment .......................................... 35
Video / Audio Menu ...................................... 34
Video / Audio Adjust ..................................... 35
Video Menu .................................................... 34
V-Chip Control Feature ......................... 30 ~ 33
VHF / UHF Antenna Input Terminal ............... 9
VOLUME UP / DOWN button ................... 8, 18
W
Warning and Instruction Displays ................ 51
Warranty ................................................. 52, 53
Weak Signal Display Feature ....................... 28
62
For assistance, please call : 1-800-211-PANA(7262) or send e-mail : [email protected]
20_27DF62 (P62-63. Index).p65
62 2002/04/16, 13:43
DVD
A
ANGLE button ........................................... 8, 37
ANGLE Indicator ....................................... 9, 37
Auto-Power Off function ............................... 17
AUDIO button ............................................ 8, 36
AUDIO OUTPUT .......................................... 47
Audio soundtrack language (DVD) .............. 36
B
Basic DVD Operation .................................... 16
C
CLEAR button ................................... 8, 39 ~ 41
D
Definition of terms ........................................... 7
Disc Audio Attribute 1 Type, Sampling
Frequency, Bit No. ................................... 36
Disc format ...................................................... 7
Disc handling ................................................... 7
Disc Information Screen ............................... 42
DISC LANGUAGES (DVD) .......................... 46
Disc Operation ...................................... 36 ~ 40
Disc Tray ............................................... 7, 9, 16
DISPLAY ............................................... 41 ~ 43
DISPLAY button ........................................ 8, 41
DVD button ................................................ 8, 16
DVD Lock Feature (DVD) ............................ 45
DVD Lock Ratings (DVD) ............................. 45
DVD menu (DVD) ......................................... 38
DVD Operation using On-Screen ........ 41 ~ 43
DVD Volume Adjust ...................................... 29
F
FF button ................................................... 8, 16
Foward / Reverse Chapter / Track skip ...... 17
Foward / Reverse rapid scene search ........ 17
Frame by Frame picture (DVD/Video CD) .. 17
K
Karaoke (DVD/Video CD) ............................. 37
L
Language Code List ...................................... 49
M
MENU button ............................................. 8, 38
MP3 Playback Operation ............................. 44
Multiple angle viewing (DVD) ........................ 37
O
OPEN / CLOSE button .............................. 8, 16
Optical digital audio output connector ...... 9, 15
P
PAUSE button ........................................... 8, 17
Picture Zoom (DVD) ..................................... 37
Play ................................................................ 16
Playback control (Video CDs) ...................... 17
PLAY button ............................................... 8, 16
Program Play (Video CD/CD) ....................... 39
Program Repeat Play (Video CD/CD) .......... 39
R
Random Play (Video CD/CD) ....................... 40
Region number ................................................ 3
Repeat Play ................................................... 43
RESUME function ......................................... 17
RETURN button ........................................ 8, 16
REW button ............................................... 8, 16
S
Settings for DVD Operation .................. 46 ~ 48
SKIP
I / I
button .......................... 8, 16, 17
Slow Motion (DVD/Video CD) ....................... 17
SLOW
/
button ............................... 8, 17
STILL MODE ................................................. 48
Still (Pause) Picture ....................................... 17
Subtitle language (DVD) ............................... 36
T
TV MODE ...................................................... 48
Title menu (DVD) .......................................... 38
U
Unit information screen (Unit) ....................... 43
Z
ZOOM button ............................................ 8, 37
63
20_27DF62 (P62-63. Index).p65
63 2002/04/16, 13:43
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
20_27DF62 (P64 BC).p65
64 2002/04/16, 13:43
P
Printed in U.S.A
LSQT0581A
M0302-0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 TABLE OF CONTENTS
- 2 INITIAL SETUP (TV)
- 2 IMPORTANT SAFEGUARDS AND PRECAUTIONS / SAFETY PRECAUTIONS
- 4 BEFORE USING
- 6 INFORMATION (UNIT, DISC)
- 8 LOCATION OF CONTROLS
- 10 CONNECTIONS / INITIAL SETUP
- 12 RESET LANGUAGE, CHANNELS, CLOCK, TIME ZONE ADJUST
- 14 AUDIO CONNECTIONS
- 16 DVD OPERATION (DVD)
- 16 BASIC DVD OPERATION
- 18 TV OPERATION (TV)
- 18 TV OPERATION
- 19 MTS BROADCAST / TV STERO SYSTEM
- 20 CLOSED CAPTION SYSTEM
- 22 TV TIMER FEATURES
- 23 ON-SCREEN DISPLAY (OSD)
- 24 FM RADIO
- 26 ADVANCED OPERATION (TV/DVD)
- 26 CABLE BOX UNIVERSAL REMOTE CONTROL FEATURE
- 28 SPECIAL FEATURES
- 30 V-CHIP CONTROL FEATURE
- 34 VIDEO / AUDIO MENU
- 35 VIDEO / AUDIO ADJUSTMENT
- 36 DISC OPERATION
- 41 DVD OPERATION USING ON-SCREEN DISPLAYS
- 44 MP3 PLAYBACK OPERATION
- 45 DVD LOCK FEATURE
- 46 SETTINGS FOR DVD OPERATION
- 49 LANGUAGE CODE LIST
- 50 FOR YOUR INFORMATION (TV)
- 50 BEFORE REQUESTING SERVICE
- 51 WARNING AND INSTRUCTION DISPLAYS
- 52 LIMITED WARRANTY
- 53 CUSTOMER SERVICES DIRECTORY
- 54 SPANISH QUICK USE GUIDE / GUIA PARA RAPIDA CONSULTA
- 62 INDEX