SERVICE MANUAL MVD4540B DVD VIDEO PLAYER & VHS VIDEO CASSETTE RECORDER ORIGINAL

Add to my manuals
72 Pages

advertisement

SERVICE MANUAL MVD4540B DVD VIDEO PLAYER & VHS VIDEO CASSETTE RECORDER ORIGINAL | Manualzz

CLASS 1

LASER PRODUCT

MVD4540B

SERVICE MANUAL

DVD VIDEO PLAYER & VHS VIDEO CASSETTE RECORDER

ORIGINAL

MFR'S VERSION B

Design and specifications are subject to change without notice.

IMPORTANT WARNING

CAUTION:

DVD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS PLAYER USES A VISIBLE LASER

BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO

OPERATE THE PLAYER CORRECTLY AS INSTRUCTED.

THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE PLAYER.

CLASS 1

LASER PRODUCT

(Printed on the Rear Panel)

WHEN THIS PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE

TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF

THIS PLAYER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

SERVICING NOTICES ON CHECKING

1. KEEP THE NOTICES

As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.

2. USE THE DESIGNATED PARTS

The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character.

Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.

3. PUT PARTS AND WIRES IN THE

ORIGINAL POSITION AFTER

ASSEMBLING OR WIRING

There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board.

The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts.

Therefore, put these parts in the original positions.

4.

PERFORM A SAFETY CHECK AFTER

SERVICING

Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades.

And be sure the safety of that.

HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)

1. MODEL NUMBER and VERSION LETTER

The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be

found at the end of the SERIAL NUMBER.

2. PART NO. and DESCRIPTION

You can find it in your SERVICE MANUAL.

A1-1

1.

2.

3.

4.

5.

TAPE REMOVAL METHOD AT NO POWER SUPPLY

Remove the Top Cabinet, Front Cabinet and DVD Block. (Refer to item 1 of the

DISASSEMBLY INSTRUCTIONS.)

Remove the screw

1

of the Deck Chassis and remove the Loading Motor. (Refer to Fig. 2)

Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.

Rotate the Clutch Ass'y either of the derections to wind the Video Tape in the Cassette Case.

Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to scratch on the tape.

Loading Motor

Screw

1

Capstan DD Unit

Pinch Roller Cam

Fig. 1

Main Cam

Main Chassis (Front Side)

Fig. 2

Clutch Ass'y

DISC REMOVAL METHOD AT NO POWER SUPPLY

1.

2.

3.

Remove the Top Cabinet and Front Cabinet. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)

Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.

(Refer to Fig. 1)

Draw the Tray.

Rack Loading

(White)

DVD Deck

Fig. 1

PARENTAL CONTROL - RATING LEVEL

4 DIGIT PASSWORD CANCELLATION

If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below.

1.

Turn Unit ON.

2.

Press and hold the '7' key on the remote control unit.

3.

Simultaneously press and hold the 'STOP' key on the front panel.

4.

Hold both keys for more than 3 seconds.

5.

The On Screen Display message 'PASSWORD CLEAR' will appear.

6.

The 4 digit password has now been cleared

A1-2

TABLE OF CONTENTS

IMPORTANT WARNING .........................................................................................................

SETVICING NOTICES ON CHECKING .....................................................................................

HOW TO ORDER PARTS ..........................................................................................................

TAPE REMOVAL METHOD AT NO POWER SUPPLY ............................................................

DISC REMOVAL METHOD AT NO POWER SUPPLY .............................................................

TABLE OF CONTENTS ..............................................................................................................

GENERAL SPECIFICATIONS ....................................................................................................

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ............................................

2. REMOVAL OF VCR PARTS ..............................................................................................

3. REMOVAL OF DVD DECK PARTS ...................................................................................

4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ..............................................

KEY TO ABBREVIATIONS ........................................................................................................

SERVICE MODE LIST ................................................................................................................

PREVENTIVE CHECKS AND SERVICE INTERVALS ..............................................................

WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................

SERVICING FIXTURES AND TOOLS .......................................................................................

PREPARATION FOR SERVICING .............................................................................................

MECHANICAL ADJUSTMENTS ................................................................................................

ELECTRICAL ADJUSTMENTS ..................................................................................................

BLOCK DIAGRAMS

DVD ..........................................................................................................................................

Y/C/AUDIO/CCD/HEAD AMP .................................................................................................

SYSCON .................................................................................................................................

OPERATION/DISPLAY ..........................................................................................................

HI-FI/DEMODULATOR ...........................................................................................................

TUNER/JACK .........................................................................................................................

POWER ..................................................................................................................................

PRINTED CIRCUIT BOARDS

DVD ..........................................................................................................................................

VCR/OPERATION ..................................................................................................................

VCR .........................................................................................................................................

SCHEMATIC DIAGRAMS

MPEG/MICON .........................................................................................................................

MEMORY .................................................................................................................................

RF AMP/DSP ...........................................................................................................................

AUDIO/VIDEO .........................................................................................................................

Y/C/AUDIO/CCD/HEAD AMP ................................................................................................

SYSCON .................................................................................................................................

TUNER/JACK .........................................................................................................................

OPERATION/DISPLAY ..........................................................................................................

HI-FI/DEMODULATOR ...........................................................................................................

POWER ..................................................................................................................................

OPERATION/LED ....................................................................................................................

INTERCONNECTION DIAGRAM ...............................................................................................

WAVEFORMS .........................................................................................................................

MECHANICAL EXPLODED VIEW .............................................................................................

CHASSIS EXPLODED VIEWS ...................................................................................................

DVD DECK EXPLODED VIEW ...................................................................................................

MECHANICAL REPLACEMENT PARTS LIST .........................................................................

CHASSIS REPLACEMENT PARTS LIST ..................................................................................

DVD DECK REPLACEMENT PARTS LIST ...............................................................................

ELECTRICAL REPLACEMENT PARTS LIST ...........................................................................

A1-1

A1-1

A1-1

A1-2

A1-2

A2-1

A3-1~A3-7

B1-1, B1-2

B2-1~B2-6

B3-1~B3-4

B4-1, B4-2

C1-1, C1-2

C2-1

C3-1, C3-2

C4-1

D1-1

D1-1

D2-1~D2-4

D3-1, D3-2

E-1, E-2

E-3, E-4

E-5, E-6

E-7, E-8

E-9, E-10

E-11, E-12

E-13, E-14

F-1, F-2

F-3, F-4

F-5, F-6

G-1, G-2

G-3, G-4

G-5, G-6

G-7, G-8

G-9, G-10

G-11, G-12

G-13, G-14

G-15, G-16

G-17, G-18

G-19, G-20

G-21, G-22

G-23, G-24

H-1, H-2

I1-1

I2-1, I2-2

I3-1

J1-1

J2-1

J3-1

J4-1, J4-2

A2-1

G - 1

G - 2

G - 3

G - 4

G - 5

G - 6

G - 7

G - 8

Outline of the product

DVD System

Color System

Disc

Disc Diameter

Deck

Pick up

Playback time (Max)

Search speed

Slow speed

GENERAL SPECIFICATIONS

Disc Loading System

Motor

DVD 1-Layer

DVD 2-Layer

CD

VIDEO CD

V C R

S y s t e m

T u n i n g

S y s t e m

System

Video System

Hi-Fi STEREO

NTSC PB(PAL60Hz)

Deck

Heads Video Head

DECK

Loading System

Motor

FM Audio Head

Tape

Speed

Audio / Control

Erase (Full Track Erase)

Rec PAL

NTSC

Play PAL

NTSC

Fast Forward / Rewind Time (Approx.) at 25oC

Forward/Reverse

Picture Search

Frame Advance

Slow Speed

Broadcasting System

Tuner and

Receive CH

NTSC or PAL-M

PAL or SECAM

System

Destination

Tuning System

Input Impedance

CH Coverage

P o w e r

Regulation

Temperature

Intermediate

Frequency

Picture (FP)

Sound (FS)

FP-FS

Preset CH

RF Converter Output

Channel

Level / Impedance

Sound Selector

Stereo / Dual TV Sound

Tuner Sound Muting

Power Source AC

DC

Power Consumption

Protector

Stand by

Per Year

Power Fuse

Safety

Radiation

Laser

Operation

Storage

Operating Humidity

DVD VIDEO PLAYER & VHS Player / Recorder

NTSC

DVD, CD-DA, CD-R/RW

120 mm , 80 mm

Front Disc Loading

2 Motors

1-Lens 2-Beams System

135min (4.7GB)

245min (8.5GB)

74min

--min

Fwd 2-20 times / 4 steps

Actual 2-45 times (DVD)

4-40 times (CD)

Rev 2-20 times / 4 steps

Actual 2-45 times (DVD)

4-40 times (CD)

Fwd 1/7-1/2 times

Actual --

Rev --

Actual --

VHS Player / Recorder

NTSC

Yes

No

OVD-7

Front

3

4Head

2Head

Mono/Yes

Yes

-

SP/SLP

-

SP/LP/SLP

FF:1'48"/REW:1'48" with Cassette T-120

SP/LP/SLP = 3x,5x / 7x,9x / 9x,15x

-

Yes

1/10

US System M

1Tuner

US (w/CATV)

F-Synth

VHF/UHF 75 OHM

2-69,4A,A-5~ A-1,A~I,

J~ W, W+1-W+84

45.75 MHz

41.25 MHz

4.50 MHz

-

Yes

3 or 4 ch

66 dBu / 75 Ohm

No

US-ST

Yes

120V 60Hz

-

18 W at 120V 60Hz

2 W at 120V 60Hz

-- W

Yes

UL

FCC

DHHS

5 o C - 40 o C

-20 o C - 60 o C

Less than 80% RH

A3-1

G - 9 S i g n a l

Video Signal

RGB Signal

Audio Signal

Hi-Fi Audio Signal

GENERAL SPECIFICATIONS

Output Level

S/N Ratio (Weighted)

Horizontal Resolution

Output Level

Input Level Microphone

Input Level Line

Output Level Line

Digital Output Level

S/N Ratio at (Weighted)

Harmonic Distortion (1KHz) Typical

Frequency Response : DVD Mode at DVD

DVD Mode at VIDEO CD

DVD Mode at CD

VCR Mode at SP

VCR Mode at LP

VCR Mode at SLP

Dynamic Range : More than

Frequency Response

Wow And Flutter : Less than

Channel Separation : More than

Harmonic Distortion : Less than

1 V p-p/75 ohm (DVD,VCR)

65 dB(DVD)

500 Lines (DVD)

-

50 dB(VCR)

230 Lines(VCR Mode)

-

-8 dBm/ 50k ohm (VCR, 0dBm=0.775Vrms)

-8 dBm/ 1k ohm (VCR,

0dBm=0.775Vrms)

-12dBm/ 1k ohm (DVD, -

20dBFs 0dBFs=2.0Vrms)

0.5 V p-p / 75 ohm(DVD)

90dB(DVD), 42dB(VCR at SP)

0.02% (1KHz) (DVD) , 1.5% (1KHz) (VCR)

4 Hz - 22 KHz

-

4 Hz - 20 KHz

100Hz - 10 KHz

-

100Hz - 4 KHz

90dB

20Hz ~20kHz

0.01 %Wrms

60 dB

0.01

A3-2

G - 1 0 On Screen

Display (DVD)

Menu

GENERAL SPECIFICATIONS

Menu Type

Language

Picture

Menu

Sub Title

Audio

Yes

Character

Yes

Yes

Yes

Yes

Yes

Yes

Yes

TV Screen Size

OSD Display On/Off

JPEG Interval

Select Files

Sound

DRC (Dynamic Range Control) dts Decode

Output (5.1ch/2ch)

Surround On/Off

Center On/Off

Sub Woofer On/Off

Yes

Yes

Parental

Other

Password Lock/Unlock

Rating Level

OSD Language (Set up Language)

Output (RGB / Composite)

Open

Close

No disc

Reading

Play

Still/Pause

Stop

Prohibit Mark

Step

Skip (>>|)

Skip (|<<)

Random

Repeat

Slow+ ##

Slow- ##

Search+ ##

Search- ##

Jump

Resume

Title No.

Chapter No.

Track No.

Time

Sub Title No.

Angle No.

Vocal On/Off

Audio No.

Audio Stereo L/R

Zoom

Marker No.

Spatializer (N-2-2)

Program Play Back

MP3

Progressive Scan Out ON/OFF

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes (CD, MP3)

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes (CD, MP3)

Folder Name Yes

File Name Yes

File No Yes

Time Yes

Track No Yes

Yes

No

No

No

No

No

No

No

No

No

No

No

A3-3

GENERAL SPECIFICATIONS

G - 1 1

G - 1 2

G - 1 3

On Screen

Display(VCR)

OSD Language

Clock,Timer and Timer

B a c k - u p

D i s p l a y

Menu

Menu Type

Timer Rec Set

Auto Repeat On/Off

SAP On/Off

CH Set-Up

TV/CATV

Auto CH Memory

Add/Delete

System Set Up

Clock Set

Language

No Noise Back Ground

Auto Clock

Standard Time

Daylight Saving Time

G-CODE(or SHOWVIEW or PLUSCODE)No. Entry

Stereo, Audio Output, SAP

Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In/Repeat

(Symbol Mark)

DVD OSD

VCR OSD

Calendar

Timer Events

One Touch Recording Max Time

OTPB Valid Time

Timer Back-up (at Power Off Mode)

DISPLAY

CH/AV(LINE)

Clock

Repeat

Tape Counter

Index

Tape Speed

ATR / Manual Tracking

ZERO Return

Hi-Fi

DISPLAY type

Yes

Character

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes (Calendar 12H)

Yes

Yes

Yes

Yes

Clock/Counter,CH,Timer Rec,OTR, Play

Rec,FF(Cue),Rew(Rev),Stop,ATR,Eject

VCR

DVD

CD

Clock

Yes

Yes

Yes

Yes (12h)

AM

Counter VCR

PM Yes

Yes (hour:min)

DVD Yes (hour:min)

CD Yes (min:sec)

Yes Eject

Counter Remain

Play

Stop

Yes

Yes Rec

FF / Cue

REW / Review

Pause / Still

OTR (ITR)

T-Rec

Chapter

TITLE

Yes

Yes

TRACK

Repeat

Hi-Fi

SP

LP

SLP

CH

RF Output CH

Tape In

Progressive Scan Out

Yes

Yes

Yes

Yes

Yes

No

No

No

No

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

English / French / Spanish

English / French / Spanish

1990/1/1 ~ 2081/12/31

8 Program/ 1 Month

6 Hours

No

5sec

Yes

LED Module (Green, "Rec" &Timer symbol = Red)

No

No

No

No

No

No

No

No

No

No

No

No

No

No

A3-4

G - 1 4 R e m o t e

C o n t r o l

G - 1 5 F e a t u r e s

( D V D )

GENERAL SPECIFICATIONS

Unit

Glow in Dark Remocon

Power Source

Total Keys

Keys

Auto Power Off

Parental Lock

Video CD Playback

MP3 Playback

WMA Playback

JPEG Playback

Progressive Scan Out

Digital Out

RC-ET

Voltage(D.C)

UM size x pcs

3

4

5

1

2

Power

DISPLAY/CALL

8

9

6

7

0

Input Select

Input Select / PROGRESSIVE

UP/CH+

DOWN/CH-

LEFT/ SET- / TRACKING-

RIGHT/ SET+ / TRACKING+

VCR/DVD

TV/VCR

DVD MENU

TITLE

SET UP MENU/VCR MENU

SELECT/ENTER

CLEAR/CANCEL

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

RETURN Yes

PLAY Yes

Yes

Yes

Yes

Yes

Yes

STOP

PAUSE/STILL/STEP

FF(Cue)/SEARCH+

REW(Review)/SEARCH-

REC/OTR

Yes

Yes

Yes

Yes

Yes

3V

UM-4 x 2 pcs

46 Keys

Yes

Yes

Yes

Yes

Yes

Yes

Yes

SKIP+ / INDEX+

SKIP- / INDEX-

AUDIO / AUDIO SELECT

ANGLE/COUNTER RESET

SUB TITLE/ATR

PLAY MODE/SPEED

T-REC

CLOCK / COUNTER

JUMP/ZERO RETURN

ZOOM

REPEAT A-B

SLOW (Forward)

MARKER

OPEN/CLOSE

EJECT

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Dolby Digital

MPEG

PCM

DTS

(Dolby Digital)

(DTS)

Yes

Yes

Yes

Yes

Yes

Yes Down Mix Out

Spatializer (N-2-2)

Screen Saver

Auto Stop

Audio DAC

Yes (5min.)

192kHz / 24bit

No

No

No

No

No

No

No

No

No

A3-5

F e a t u r e s

( V C R )

G - 1 6 Accessories

GENERAL SPECIFICATIONS

Auto Head Cleaning

Auto Tracking

HQ (VHS Standard High Quality)

Auto Power On, Auto Play, Auto Rewind, Auto Eject

Auto Power Off

Forward/Reverse Picture Search

VIDEO PLUS+ (SHOWVIEW, G-CODE)

One Touch Playback

Auto CH Memory

AREA CODE

Auto Clock Set

Index Search

SQPB

CATV

Energy Star

MTS (SAP)

CM Skip (30sec x 6 Times)

Copy (Disc to Tape)

Owner's Manual Language w/Guarantee Card

Buyer Model No.

Remote Control Unit

Guarantee Card

Registration Card

Warning Sheet

Service Station List

Important Tag

AC Plug Adapter

Quick Set-up Sheet

Battery

UM size x pcs

AC Cord

AV Cord

75 Ohm Coaxial Cable

S-Video Cable

21pin cable

800 No Sticker

Toll Free Insert Sheet

Safety Tip

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

English / Spanish

MVD4540B

Yes

Yes

--

Yes (1.2m)

Yes (0.9m)

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

No

A3-6

G - 1 7 I n t e r f a c e

G - 1 8

G - 1 9

G - 2 0

Set Size

W e i g h t

C a r t o n

G - 2 1 M a t e r i a l

G - 2 2 Environment

Switch

Volume

Terminals

Indicator

GENERAL SPECIFICATIONS

Front

Rear

Front

Rear

LED

Pb Free

Cd Free

Power

Play

Eject (VCR)

Stop

Rec/OTR

Open/Close (DVD)

CH +

CH -

FF/ Search(>>)

Rew/Search(<<)

Still/Pause

Shuttle (Search/REV/FWD)

DVD/VCR

Main Power SW

Attenuator

S-Video/Component Video Selector

RF Out (Slide SW)

Main Power SW

Phones Volume

Mic Volume

Echo Volume

Rec/OTR

Video In

Audio In

Video Output

Audio Output

Optical Out (Option)

Video Input (Option)

Audio Input (Option)

RF Input / Output

Euro Scart

AC Inlet

Power

Rec

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

Yes

RCA x1 (Yellow)

RCA x 2 (Stereo, White/Red)

No

No

No

No

No

No

RCA x1 (Yellow)

S-Video x 1 (DVD Signal Only)

Component x1 (RCA 3pin,DVD Signal Only)

RCA x 4 (Stereo, White/Red)

Coaxial x 1 (Digital Audio,DVD Signal Only)

Yes (Digital Audio,DVD Signal Only)

Yes

No

No

No

No

No

No

T-Rec

TV/VCR

DVD

VCR

Yes (RED)

Yes (RED)

Surround

Level Meter

Net (Approx.)

Gross (Approx.)

Approx. W x D x H (mm) 430 x 253 x 99

3.6 kg( 7.9lbs)

4.7 kg( 10.4lbs)

Master Carton

Content

Material

Dimensions W x D x H(mm)

Description of Origin

Gift Box

--- Sets

--- / ---

---

---

Yes

Double/White Material

W/Color Photo Label

Dimensions W x D x H(mm)

Design

Description of Origin

Drop Test

Height (cm)

Container Stuffing

Cabinet

PCB

Front

Non-Halogen Demand

497 x 360 x 180

As Per BUYER 's

Yes

No

No

No

No

No

No

Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces

80 cm

1,985 Sets/40' container

PS 94V2 or More / DECABROM

No

Eyelet Demand

Lead-free Solder

Other

No

No

No

No

A3-7

Top Cabinet

DISASSEMBLY INSTRUCTIONS

1.

REMOVAL OF MECHANICAL PARTS

AND P.C. BOARDS

1-1: TOP CABINET, OPERATION PCB AND

FRONT CABINET (Refer to Fig. 1-1)

1.

2.

3.

4.

5.

6.

7.

Remove the 5 screws (1).

Remove the Top Cabinet in the direction of arrow (A).

Disconnect the following connector: (CP651).

Unlock the 8 supports (2).

Remove the Front Cabinet in the direction of arrow (B).

Remove the 2 screws (3).

Remove the Operation PCB in the direction of arrow (C).

(1)

(1)

1-3: DVD DECK (Refer to Fig. 1-3)

1.

Make the short circuit on the position as shown Fig. 1-3

2.

using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged.

Unlock the support (1) and remove the Deck Top

Holder in the direction of arrow (A).

Remove the 3 screws (2).

3.

4.

5.

6.

7.

Remove the screw (3).

Disconnect the following connectors: (CP2601, CP2602 and CP2603).

Remove the DVD Deck in the direction of arrow (B).

Remove the 3 screws (4).

8.

9.

Remove the Front Angle in the direction of arrow (C).

Remove the screw (5).

10.

Remove the DVD Angle.

(1)

(1)

Deck Top Holder

DVD Deck

(2)

(3)

(2)

Pick Up PCB

(A)

(1)

Front Cabinet

(1)

(2)

(2)

(2)

(2)

(2)

(B)

(3)

(2)

(2)

(C)

(2)

(2)

(3)

Operation PCB

Fig. 1-1

(4)

(4)

(A)

(B)

Make the sort circuit using a soldering.

DVD Angle

(5)

(C)

1-2: FLAP (Refer to Fig. 1-2)

1.

2.

Open Flap to 90

°

and flex in direction of arrow (A), at the same time slide in direction of arrow (B).

Then lift in direction of arrow (C).

(4)

Front Angle

Fig. 1-3

(A)

NOTE

When the installation of the DVD Deck, remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.

(C)

(B)

Flap

Fig. 1-2

B1-1

DISASSEMBLY INSTRUCTIONS

1-4: DVD PCB (Refer to Fig. 1-4)

1.

2.

3.

4.

Remove the 3 screws (1).

Remove the 4 screws (2).

Disconnect the following connectors: (CP4002 and

CP8102).

Remove the DVD PCB in the direction of arrow.

1-6: VCR PCB (Refer to Fig. 1-6)

1.

2.

3.

4.

5.

Remove the screw (1).

Remove the screw (2).

Remove the screw (3).

Remove the 3 Pin Shield.

Remove the VCR PCB in the direction of arrow.

(1)

(3)

VCR PCB

(1)

(1)

DVD PCB

3 Pin Shield

(1)

(2)

(2)

(2)

(2)

(2)

Fig. 1-4

1-5: VCR DECK (Refer to Fig. 1-5)

NOTE

Do not remove the cable at the FE Head section. The FE

Head may be damaged if you remove the cable by force.

1.

2.

3.

4.

5.

6.

Move the Cassette Holder Ass’y to the back side.

Remove the screw (1).

Remove the FE Head.

Remove the 3 screws (2).

Disconnect the following connectors: (CP101, CP102, and CP3001).

Remove the AC Head Cover and VCR Deck in the direction of arrow.

(1)

(2)

(2)

(2)

FE Head

AC Head Cover

VCR Deck

Fig. 1-6

Fig. 1-5

B1-2

DISASSEMBLY INSTRUCTIONS

2. REMOVAL OF VCR DECK PARTS

2-1: TOP BRACKET (Refer to Fig. 2-1)

1.

2.

Extend the 2 supports (1).

Slide the 2 supports (2) and remove the Top Bracket.

NOTE

1. After the installation of the Top Bracket, bend the support (1) so that the Top Bracket is fixed.

NOTE

1.

2.

In case of the Locker R installation, check if the one position of Fig.2-3-B are correctly locked.

When you install the Cassette Side R, be sure to move the Locker R after installing.

Locker R

Top Bracket

Check if this position is locked.

Cassette Side R

(1)

(1)

Top Bracket

(2)

Fig. 2-3-B

(2)

Main Chassis

Main Chassis

Fig. 2-1

2-4: LINK UNIT (Refer to Fig. 2-4)

1.

2.

3.

Set the Link Unit to the Eject position.

Unlock the support (1).

Remove the (A) side of the Link Unit first, then remove the (B) side.

2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2)

1.

2.

3.

Move the Cassette Holder Ass'y to the front side.

Push the Locker R to remove the Cassette Side R.

Remove the Cassette Side L.

Main Chassis

Cassette Side R

Locker R

Main Chassis

Link Unit

(1)

(A)

Link Unit

(B)

Main Chassis

Link Unit

Cassette Side L

Main Chassis

Fig. 2-2

Fig. 2-4

2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5)

1.

2.

3.

Extend the support (1).

Remove the Link Lever.

Remove the Flap Lever.

2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)

1.

2.

3.

Remove the Locker Spring.

Unlock the 4 supports (1) and then remove the

Cassette Side L/R.

Unlock the support (2) and then remove the Locker R.

Locker Spring

(1)

(1)

(2)

Cassette Holder

(1)

Flap Lever

Link Lever

Fig. 2-5

Locker R

(1)

(1)

Cassette Side R

Cassette Side L

Fig. 2-3-A

B2-1

DISASSEMBLY INSTRUCTIONS

2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)

1.

2.

3.

Remove the screw (1).

Remove the Loading Motor.

Remove the Worm.

Worm

Loading Motor

2-7: TENSION ASS'Y (Refer to Fig. 2-7-B)

1.

2.

3.

4.

5.

6.

Turn the Pinch Roller Cam clockwise so that the

Tension Holder hook is set to the position of Fig. 2-7-A to move the Tension Arm Ass'y.

Remove the Tension Spring.

Unlock the 2 supports (1) and remove the Tension

Band.

Unlock the support (2) and remove the Tension Arm

Ass'y.

Unlock the support (3) and remove the Tension

Connect.

Float the hook (4) and turn it clockwise then remove the Tension Holder.

Main Chassis

Tension Arm Ass'y

•Screw Torque: 3

±

0.5kgf•cm

(1)

Fig. 2-6-A

NOTE

1.

2.

In case of the Worm installation, check if the value of the Fig. 2-6-B is correct.

In case of the Loading Motor installation, hook the wire

3.

on the Cassette Opener as shown Fig. 2-6-C.

When installing the wires between Capstan DD Unit and Loading Motor, connect them correctly as shown

Fig. 2-6-D.

19.2

±

0.1mm

Fig. 2-7-A

(3)

(1)

(1)

Tension Connect

Tension Spring

Tension Band

(2)

(4)

Tension Arm Ass'y

Tension Holder

Safety surface for pressing of the insert.

Fig. 2-6-B

Fig. 2-7-B

NOTE

1.

2.

3.

In case of the Tension Band installation, note the direction of the installation. (Refer to Fig. 2-7-C)

In case of the Tension Band installation, install correctly as Fig. 2-7-D.

In case of the Tension Connect installation, install as the circled section of Fig. 2-7-E.

Loading Motor

-

+

Pink

White

Loading Motor

Cassette Opener

Fig. 2-6-C

Capstan DD Unit

L2

L1

Fig. 2-6-D

Tension Connect

[OK]

[NG]

Tension Connect

Tension Connect

Tension Band

Fig. 2-7-C

Tension Band

Tension Band

Fig. 2-7-D

Tension Connect

Main Chassis

Fig. 2-7-E

B2-2

DISASSEMBLY INSTRUCTIONS

2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A)

1.

2.

3.

Remove the T Brake Spring.

Turn the T Brake Arm clockwise and bend the hook section to remove it.

Unlock the 2 supports (1) and remove the T Brake

Band.

Idler Gear

S Reel

(B)

T Brake Band

(A)

(1)

(1)

(1)

Hook section

T Brake Arm

T Brake Spring

Idler Arm Ass'y

(1)

T Reel

(A)

Fig. 2-8-A

NOTE

1. In case of the T Brake Band installation, install correctly as Fig. 2-8-B.

[OK]

T Brake Band

[NG]

T Brake Band

T Brake Arm

T Brake Arm

Fig. 2-8-B

2-9: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR

(Refer to Fig. 2-9-A)

1.

2.

3.

Remove the S Reel and T Reel.

Remove the 2 Polyslider Washers (1).

Remove the Idler Arm Ass'y and Idler Gear.

NOTE

1.

2.

3.

4.

5.

6.

Take care not to damage the gears of the S Reel and T

Reel.

The Polyslider Washer may be remained on the back of the reel.

Take care not to damage the shaft.

Do not touch the section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains on it.

When you install the reel, clean the shaft and grease it

(FG-84M). (If you do not grease, noise may be heard in

FF/REW mode.)

After installing the reel, adjust the height of the reel.

(Refer to MECHANICAL ADJUSTMENT)

Fig. 2-9-A

NOTE

1.

2.

In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-9-B)

In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-9-C. And also set it so that the section "B" of

Fig. 2-9-A is placed under the Main Chassis tab.

[OK]

Clutch Gear

[NG]

Clutch Gear

Big Hole

(S Reel)

Small Hole

(T Reel)

Fig. 2-9-B

Idler Arm Ass'y

Idler Arm Ass'y

Fig. 2-9-C

B2-3

DISASSEMBLY INSTRUCTIONS

2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/

P5 ARM ASS'Y (Refer to Fig. 2-10-A)

1.

2.

Unlock the support (1) and remove the Cassette

Opener.

Remove the Pinch Roller Block and P5 Arm Ass'y.

Cassette Opener

(1)

Spring Position

Pinch Roller Block

P5 Arm Ass'y

Main Chassis

Fig. 2-11-B

2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12)

1.

2.

Remove the screw (1).

Remove the FE Head.

(1)

FE Head

Fig. 2-10-A

NOTE

1.

2.

Do not touch the Pinch Roller. (Use gloves.)

In case of the Pinch Roller Block and the Pinch Roller

Cam installation, install correctly as Fig. 2-10-B.

Pinch Roller Block

P5 Arm Ass'y

Can be seen the hole of the Pinch Roller Cam.

Can be seen the hole of the

Main Cam.

Fig. 2-10-B

2-11: A/C HEAD (Refer to Fig. 2-11-A)

1.

2.

3.

4.

Remove the screw (1).

Remove the A/C Head Base.

Remove the 3 screws (2).

Remove the A/C Head and A/C Head Spring.

NOTE

1.

2.

3.

Do not touch the A/C Head. (Use gloves.)

When you install the A/C Head Spring, install as shown in Fig. 2-11-B.

When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).

(2)

(2)

(2)

(1)

(3)

(2)

A/C Head

• Screw Torque: 5

±

0.5kgf•cm

•The FE Head is not installed on the Video Cassette Player.

Fig. 2-12

2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y

(Refer to Fig. 2-13)

1.

2.

3.

4.

Unlock the support (1) and remove the AHC Ass'y.

Disconnect the following connector:

(CD2001)

Remove the 3 screws (2).

Remove the Cylinder Unit Ass'y.

NOTE

1.

When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.

Cylinder Unit Ass'y

(1)

AHC Ass'y

A/C Head Spring

(1)

(2)

• Screw Torque: 3

±

0.5kgf•cm

(2)

(2)

(2)

(3)

Fig. 2-13

(1)

• Screw Torque: 5

±

0.5kgf•cm

A/C Head Base

Fig. 2-11-A

B2-4

DISASSEMBLY INSTRUCTIONS

2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14-A)

1.

2.

3.

Remove the Capstan Belt.

Remove the 3 screws (1).

Remove the Capstan DD Unit.

2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR

(Refer to Fig. 2-15-A)

1.

2.

Remove the E-Ring (1), then remove the Main Cam.

Remove the E-Ring (2), then remove the Pinch Roller

Cam and Joint Gear.

(1)

Main Cam

Capstan Belt

Capstan DD Unit

(2)

Pinch Roller Cam

Joint Gear

(1)

• Screw Torque: 4

±

0.5kgf•cm

(1)

(1)

Fig. 2-14-A

NOTE

1.

In case of the Capstan DD Unit installation, apply the silicon bond (TSE3843-W) on the position Fig. 2-14-B correctly. (If no silicon bond applied, abnormal noise will be heard on the deck operation.)

(Refer to Fig. 2-14-B, C)

Applied position of silicon bond

Fig. 2-15-A

NOTE

1.

In case of the Pinch Roller Cam and Main Cam installation, install them as the circled section of Fig. 2-

15-B so that the each markers are met. (Refer to Fig.

2-15-B)

Pinch Roller Cam

Marker

Be careful not to apply the silicon bond to the Pinch Roller.

Main Cam

Capstan DD Unit

Fig. 2-14-B

Silicon Bond

Main Chassis

Fig. 2-14-C

Fig. 2-15-B

2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A)

1.

2.

Remove the E-Ring (1) and remove the Main Loading

Gear.

Remove the Main Rod, Tension Lever, Loading Arm S

Unit and Loading Arm T Unit.

(1)

Main Loading Gear

Main Rod

Loading Arm T Unit

Tension Lever

Loading Arm S Unit

Fig. 2-16-A

B2-5

Main Loading Gear

DISASSEMBLY INSTRUCTIONS

NOTE

1. When you install the Loading Arm S Unit, Loading Arm

T Unit and Main Loading Gear, align each marker.

(Refer to Fig. 2-16-B)

Marker

2-18: CASSETTE GUIDE POST/INCLINED BASE S/T

UNIT/P4 CAP/LED REFLECTOR

(Refer to Fig. 2-18-A)

1.

2.

3.

4.

5.

Remove the P4 Cap.

Unlock the support (1) and remove the Cassette Guide

Post.

Remove the Inclined Base S/T Unit.

Remove the screw (2).

Remove the LED Reflector.

Marker

Cassette Guide Post

(1)

Inclined Base S

Unit

Inclined Base T

Unit

P4 Cap

Loading Arm T Unit Loading Arm S Unit

Fig. 2-16-B

2-17: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/

CLUTCH GEAR (Refer to Fig. 2-17-A)

1.

2.

3.

4.

Remove the Polyslider Washer (1).

Remove the Clutch Ass'y and Ring Spring.

Remove the Clutch Lever.

Remove the Coupling Gear, Coupling Spring and

Clutch Gear.

(1)

Clutch Ass'y

Ring Spring

Coupling Gear

Coupling Spring

Clutch Gear

Clutch Lever

LED Reflector

• Screw Torque: 5

±

0.5kgf•cm

(2)

Fig. 2-18-A

NOTE

1.

2.

3.

Do not touch the roller of Guide Roller.

In case of the P4 Cap installation, install it with parallel for "A" and "B" of Fig. 2-18-B.

In case of the Cassette Guide Post installation, install correctly as the circled section of Fig. 2-18-C.

"A" "B"

P4 Cap

Fig. 2-17-A

NOTE

1.

In case of the Clutch Ass'y installation, install it with inserting the spring of the Clutch Ass'y into the dent of the Coupling Gear. (Refer to Fig. 2-17-B)

Clutch Ass'y

[OK]

Cassette Guide Post

Coupling Gear

Fig. 2-17-B

B2-6

[NG]

Cassette Guide Post

Cassette Opener

Fig. 2-18-B

Fig. 2-18-C

DISASSEMBLY INSTRUCTIONS

3. REMOVAL OF DVD DECK PARTS

NOTE

1. Do not disassemble the DVD DECK PARTS except listed parts here. Minute adjustments are needed if the disassemble is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.

3-1: TRAY (Refer to Fig. 3-1-A)

1.

Set the Tray opened. (Refer to the DISC REMOVAL

2.

METHOD AT NO POWER SUPPLY)

Unlock the support (1) and remove the Tray.

NOTE

1. In case of the Main Chassis Ass'y, install it from (1) to

(6) in order. (Refer to Fig. 3-2-B)

Rack Loading

(1)

(2)

(3)

Main Chassis Ass'y

(4)

(6)

Move it to the direction of the arrow.

Main Frame Ass'y

(5)

(6)

Check Lock

(4)

(5)

Main Frame Ass'y

(1)

Tray

Fig. 3-2-B

Fig. 3-1-A

NOTE

1. In case of the Tray installation, install them as the circled section of Fig. 3-1-B so that the each markers are met.

Tray

3-3: RACK LOADING/MAIN GEAR/ RACK LOADING

SPRING (Refer to Fig. 3-3)

1.

2.

3.

Remove the Rack L Spring.

Press down the catcher (1) and slide the Rack Loading.

Remove the Rack Loading, Rack Loading Spring and

Main Gear.

Rack Loading

Main Gear

Rack Loading Spring

Rack L Spring

Main Frame Ass'y

Fig. 3-1-B

3-2: MAIN CHASSIS ASS'Y (Refer to Fig. 3-2-A)

1.

2.

3.

Remove the Main Chassis Ass'y from the Insulator (R).

Unlock the support (1).

Remove the Main Chassis Ass'y.

Insulator (R)

(Green)

Main Frame Ass'y

(1)

Main Frame Ass’y

(1)

Fig. 3-3

3-4: CLAMPER ASS'Y/INSULATOR(R)/LEVER SWITCH

(Refer to Fig. 3-4-A)

1.

2.

3.

4.

5.

Remove the screw (1).

Remove the Lever Switch.

Remove the 2 Insulator (R).

Press the Clamper and rotate the Clamper Plate clockwise, then unlock the 3 supports (2).

Remove the Clamper Plate, Clamper Magnet and

Clamper.

Clamper Plate

Clamper Magnet

Insulator (R)

(Green)

Insulator (R)

(Green)

Main Frame

Main Chassis Ass'y

Fig. 3-2-A

Lever Switch

(1)

(2) (2)

(2)

Clamper

Fig. 3-4-A

B3-1

DISASSEMBLY INSTRUCTIONS

NOTE

1.

2.

3.

When installing the Clamper Magnet, install it with the green face up.

When installing the wire of the Lever Switch, install it correctly as Fig. 3-4-B.

When installing the Lever Switch, install it correctly as

4.

Fig. 3-4-C.

In case of the Lever Switch installation, hook the wire on the Main Frame as shown Fig. 3-4-D.

Main Chassis Ass'y

Lever Switch

Traverse Holder

3-6: SWITCH PCB ASS'Y (Refer to Fig. 3-6-A)

1.

2.

Remove the screw (1).

Remove the Switch PCB Ass'y.

Fig. 3-5-B

(1)

Switch PCB Ass'y

Blue

White

Red

From DVD PCB

Fig. 3-4-B

Rack Loading

The Lever should be position between A and B.

A B

Main Chassis Ass'y

• Screw Torque: 4

±

0.5kgf•cm

Fig. 3-6-A

NOTE

1. When installing the wire of the Switch PCB, install it correctly as Fig. 3-6-B.

Switch PCB Ass'y

Fig. 3-4-C

Black

White

From Relay PCB

3-5: TRAVERSE HOLDER/INSULATOR (F)

(Refer to Fig. 3-5-A)

1.

2.

Remove the Traverse Holder.

Remove the 2 Insulator (F).

Main Chassis Ass'y

Insulator (F)

(Black)

Traverse Holder

Lever Switch

Fig. 3-4-D

Fig. 3-6-B

3-7: RACK FEED ASS'Y (Refer to Fig. 3-7-A)

1.

2.

Remove the screw (1).

Remove the Rack Feed 1A Spring, Rack Feed 1/2 and

Rack Feed Lever.

(1)

Rack Feed 2

Rack Feed 1A Spring

Rack Feed Lever

Rack Feed 1

Main Chassis Ass'y

Insulator (F)

(Black)

Fig. 3-5-A

NOTE

1. After the installing of the Traverse Holder, check if the wire is like Fig. 3-5-B.

B3-2

• Screw Torque: 3.5

±

0.5kgf•cm Fig. 3-7-A

DISASSEMBLY INSTRUCTIONS

NOTE

1.

2.

After the assembly of the Rack Feed, check if the Rack

Feed 1/2 is moving smoothly. (Refer to Fig. 3-7-B)

In case of the Rack Feed Ass'y installation, install correctly as Fig. 3-7-C.

3-9: GEAR (Refer to Fig. 3-9-A)

1.

2.

Unlock the support (1).

Remove the Middle Gear 1/2/3, Idler Gear and Feed

Gear.

Middle Gear 2

Moving smoothly

Middle Gear 1

Middle Gear 3

Idler Gear

Feed Gear

Moving smoothly

Fig. 3-7-B

Should not be engaged.

Check the position of the Rack Feed Lever.

3-8: RELAY PCB ASS'Y (Refer to Fig. 3-8-A)

1.

2.

Remove the screw (1).

Remove the Relay PCB Ass'y.

Main Chassis Ass'y

Fig. 3-7-C

Main Chassis Ass'y

(1)

Fig. 3-9-A

NOTE

1.

In case of the Idler Gear installation, install correctly as

Fig. 3-9-B.

2.

When installing the Middle Gear 2, check if the Middle

Gear 2 is locked correctly as Fig. 3-9-C.

[OK]

Idler Gear

[NG]

Idler Gear

Relay PCB Ass'y

• Screw Torque: 4

±

0.5kgf

• cm

(1)

Fig. 3-8-A

NOTE

1. When installing the wire of the Relay PCB, install it correctly as Fig. 3-8-B.

Idler Arm

Check Lock

Idler Arm

Fig. 3-9-B

Middle Gear 2

3-10: IDLER ARM 2 (Refer to Fig. 3-10-A)

1.

Remove the Idler Arm 2.

Fig. 3-9-C

Idler Arm 2

Main Chassis Ass'y

Fig. 3-10-A

Fig. 3-8-B

B3-3

DISASSEMBLY INSTRUCTIONS

3-11: FEED MOTOR (Refer to Fig. 3-11-A)

1.

2.

3.

Remove the 2 screws (1).

Remove the Feed Motor.

Remove the Motor Gear.

(1) (1)

Main Chassis Ass'y

Motor Gear

Feed Motor

• Screw Torque: 1

±

0.5kgf•cm

Fig. 3-11-A

NOTE

1.

2.

In case of the Motor Gear installation, check if the value of the Fig. 3-11-B is correct.

When installing the Feed Motor, check if the cable is positioned as Fig. 3-11-C.

Motor Gear

Feed Motor

Safety surface for pressing of the insert.

Main Chassis Ass'y

6.1

±

0.1mm

Fig. 3-11-B

Pass the cable between 2 pins.

Feed Motor

Fig. 3-11-C

B3-4

DISASSEMBLY INSTRUCTIONS

4.

REMOVAL AND INSTALLATION OF

FLAT PACKAGE IC

REMOVAL

1.

Put the Masking Tape (cotton tape) around the Flat

Package IC to protect other parts from any damage.

(Refer to Fig. 4-1.)

NOTE

Masking is carried out on all the parts located within

10 mm distance from IC leads.

3.

When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 4-3.)

NOTE

Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.

Blower type IC desoldering machine

Masking Tape

(Cotton Tape)

IC

Tweezers

Fig. 4-1

2.

Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 4-2.)

NOTE

Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely.

Blower type IC desoldering machine

IC

Fig. 4-3

4.

Peel off the Masking Tape.

5.

Absorb the solder left on the pattern using the Braided

Shield Wire. (Refer to Fig. 4-4.)

NOTE

Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.

Braided Shield Wire

Soldering Iron

IC

IC pattern

Fig. 4-4

Fig. 4-2

B4-1

INSTALLATION

DISASSEMBLY INSTRUCTIONS

4.

When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 4-8.)

1.

Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.

(Refer to Fig. 4-5.)

IC

Thin-tip Soldering Iron

Soldering Iron

Solder temporarily

Solder temporarily

Fig. 4-5

2.

Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads.

(Refer to Fig. 4-6.)

Fig. 4-8

5.

Finally, confirm the soldering status on four sides of the

IC using a magnifying glass.

Confirm that no abnormality is found on the soldering position and installation position of the parts around the

IC. If some abnormality is found, correct by resoldering.

NOTE

When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.

Solder Soldering Iron

IC

Supply soldering from upper position to lower position

Fig. 4-6

3.

Absorb the solder left on the lead using the Braided

Shield Wire. (Refer to Fig. 4-7.)

NOTE

Do not absorb the solder to excess.

Soldering Iron

IC

Braided Shield Wire

Fig. 4-7

B4-2

A

B

C

D

E

F

G

H

A/C

ACC

AE

AFC

AFT

AFT DET

AGC

AMP

ANT

A.PB

APC

ASS’Y

AT

AUTO

A/V

BGP

BOT

BPF

BRAKE SOL

BUFF

B/W

C

CASE

CAP

CARR

CH

CLK

CLOCK (SY-SE)

COMB

CONV

CPM

CTL

CYL

CYL-M

CYL SENS

DATA (SY-CE) dB

EOT

EQ

EXT

F

FBC

FE

FF

FG

FL SW

FM

DC

DD Unit

DEMOD

DET

DEV

E

EF

EMPH

ENC

ENV

FSC

FWD

GEN

GND

H.P.F

Audio/Control

Automatic Color Control

Audio Erase

Automatic Frequency Control

Automatic Fine Tuning

Automatic Fine Tuning Detect

Automatic Gain Control

Amplifier

Antenna

Audio Playback

Automatic Phase Control

Assembly

All Time

Automatic

Audio/Video

Burst Gate Pulse

Beginning of Tape

Bandpass Filter

Brake Solenoid

Buffer

Black and White

Capacitance, Collector

Cassette

Capstan

Carrier

Channel

Clock

Clock (Syscon to Servo)

Combination, Comb Filter

Converter

Capstan Motor

Control

Cylinder

Cylinder-Motor

Cylinder-Sensor

Data (Syscon to Servo)

Decibel

Direct Current

Direct Drive Motor Unit

Demodulator

Detector

Deviation

Emitter

Emitter Follower

Emphasis

Encoder

Envelope

End of Tape

Equalizer

External

Fuse

Feed Back Clamp

Full Erase

Fast Forward, Flipflop

Frequency Generator

Front Loading Switch

Frequency Modulation

Frequency Sub Carrier

Forward

Generator

Ground

High Pass Filter

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

KEY TO ABBREVIATIONS

I

K

L

M

N

O

P

R

S

MIX

MM

MOD

MPX

MS SW

NC

NR

OSC

OPE

PB

PB CTL

PB-C

PB-Y

PCB

P. CON

PD

PG

P-P

R

REC

H.SW

Hz

IC

IF

IND

INV

KIL

L

LED

LIMIT AMP

LM, LDM

LP

L.P.F

LUMI.

M

MAX

MINI

REC-C

REC-Y

REEL BRK

REEL S

REF

REG

REW

REV, RVS

RF

RMC

RY

S. CLK

S. COM

S. DATA

SEG

SEL

SENS

SER

SI

SIF

SO

SOL

SP

STB

SW

Head Switch

Hertz

Integrated Circuit

Intermediate Frequency

Indicator

Inverter

Killer

Left

Light Emitting Diode

Limiter Amplifier

Loading Motor

Long Play

Low Pass Filter

Luminance

Motor

Maximum

Minimum

Mixer, mixing

Monostable Multivibrator

Modulator, Modulation

Multiplexer, Multiplex

Mecha State Switch

Non Connection

Noise Reduction

Oscillator

Operation

Playback

Playback Control

Playback-Chrominance

Playback-Luminance

Printed Circuit Board

Power Control

Phase Detector

Pulse Generator

Peak-to Peak

Right

Recording

Recording-Chrominance

Recording-Luminance

Reel Brake

Reel Sensor

Reference

Regulated, Regulator

Rewind

Reverse

Radio Frequency

Remote Control

Relay

Serial Clock

Sensor Common

Serial Data

Segment

Select, Selector

Sensor

Search Mode

Serial Input

Sound Intermediate Frequency

Serial Output

Solenoid

Standard Play

Serial Strobe

Switch

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

C1-1

S

T

U

V

X

Y

SYNC

SYNC SEP

TR

TRAC

TRICK PB

TP

UNREG

V

VCO

VIF

VP

V.PB

VR

V.REC

VSF

VSR

VSS

V-SYNC

VT

X’TAL

Y/C

KEY TO ABBREVIATIONS

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

: Synchronization

Sync Separator, Separation

Transistor

Tracking

Trick Playback

Test Point

Unregulated

Volt

Voltage Controlled Oscillator

Video Intermediate Frequency

Vertical Pulse, Voltage Display

Video Playback

Variable Resistor

Video Recording

Visual Search Fast Forward

Visual Search Rewind

Voltage Super Source

Vertical-Synchronization

Voltage Tuning

Crystal

Luminance/Chrominance

C1-2

SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.

To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit or on the main unit and on the remote control for more than a standard time (second).

Set Key Set Key

Standard Time

(seconds)

Operations

PLAY/REC total hours are displayed on the TV Monitor.

Refer to the “PREVENTIVE CHECKS AND SERVICE INTERVALS”

(CONFIRMATION OF HOURS USED).

CH UP FF 2

CH UP STOP 2

Can be checked of the INITIAL DATA of MEMORY IC.

Refer to the “WHEN REPLACING EEPROM (MEMORY) IC”.

Adjust the PG SHIFTER automatically.

Refer to the “ELECTRICAL ADJUSTMENT” (PG SHIFTER).

CH UP

CH DOWN

PLAY

POWER

2

2

Initialization of the factory on VCR.

NOTE: Do not use this for the normal servicing.

If you set a factory initialization, the memories are reset such as the clock setting, the channel setting, and PLAY/REC total hours.

VCR operation mode at no connection of DVD.

Refer to the “PREPARATION FOR SERVICING”

NOTE: Although the DVD is connected, the DVD mode cannot be selected.

Set Key

REC

STOP

Remocon Key

Standard Time

(seconds)

4

7

2

3

Operations

Initialization of the factory on DVD.

NOTE: Do not use this for the normal servicing.

The function will only work without the setting of DVD disc at

DVD mode.

While pressing the Remocon Key for more than the Standard

Time, press the Set Key simultaneously.

Releasing of PARENTAL LOCK.

Refer to the “PARENTAL CONTROL - RATING LEVEL”.

NOTE: The function will only work without the setting of DVD disc at

DVD mode.

Method

Press the ATR button on the remote control for more than

2 seconds during PLAY.

Make the short circuit between the test point of

SERVICE and the GND.

Operations

Adjusting of the Tracking to the center position.

Refer to the “MECHANICAL ADJUSTMENT” (GUIDE ROLLER) and “ELECTRICAL

ADJUSTMENT” (PG SHIFTER).

The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape.

Refer to the “PREPARATION FOR SERVICING”

C2-1

PREVENTIVE CHECKS AND SERVICE INTERVALS

The following standard table depends on environmental conditions and usage.

Parts replacing time does not mean the life span for individual parts.

Also, long term storage or misuse may cause transformation and aging of rubber parts.

The following list means standard hours, so the checking hours depends on the conditions.

1,500 hours

2,000 hours

2,500 hours

Notes

Time

Parts Name

Audio Control Head

Full Erase Head

(Recorder only)

Capstan Belt

Pinch Roller

Capstan DD Unit

Loading Motor

Tension Band

T Brake Band

Clutch Ass’y

Idler Arm Ass’y

Capstan Shaft

Tape Running

Guide Post

Cylinder Unit

500 hours

1,000 hours

: Clean

: Check it and if necessary, replace it.

Clean those parts in contact with the tape.

Clean the rubber, and parts which the rubber touches.

Replace when rolling becomes abnormal.

Clean the Head

CONFIRMATION OF HOURS USED

PLAY/REC total hours can be checked on the screen.

Total hours are displayed in 16 system of notation.

NOTE: If you set a factory initialization, the total hours is reset to “0”.

1.

2.

3.

4.

Connect the set to TV Monitor.

Turn on the POWER.

Press both CH UP button on the set and the FF button on the set for more than 2 seconds.

The Fig. 1 screen will appear on TV Monitor.

After the confirmation of using hours, turn off the power.

INIT 00 0E

PLAY/REC 0010

Fig. 1

Initial setting content of MEMORY IC.

PLAY/REC total hours.

= (16 x 16 x 16 x thousands digit value)

+ (16 x 16 x hundreds digit value)

+ (16 x tens digit value)

+ (ones digit value)

C3-1

PREVENTIVE CHECKS AND SERVICE INTERVALS

CLEANING

NOTE

After cleaning the heads with isopropyl alcohol, do not run a tape until the heads dry completely. If the heads are not completely dry and alcohol gets on the tape, damage may occur.

1. AUDIO CONTROL HEAD

Clean the Audio Control Head with the cotton stick soaked by alcohol. Clean the full erase head in the same manner. (Refer to the figure below.)

2. TAPE RUNNING SYSTEM

When cleaning the tape transport system, use the gauze moistened with isopropyl alcohol.

3. CYLINDER

Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol. Hold it to the cylinder head softly.

Turn the cylinder head counterclockwise to clean it (in the direction of the arrow). (Refer to the figure below.)

NOTE

Do not exert force against the cylinder head. Do not move the chamois upward or downward on the head.

Use the chamois one by one.

Cylinder Head

Audio Control Head

C3-2

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1.

NOTE: INI 34 and INI 35 cannot be set. Because, the total time for the PLAY/REC of the main unit is recorded.

INIT +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F

00 0E

00 BC 60 64 64 4A 26 0B 2B 86 32 0A 08 0A 0F

10

AF 97 95 8A A0 90 31 04 88 A5 9F 3A 00 10 BF 00

20 3A 11 22 70 61 2A 3A 00 0B 00 00 C5 A2 B0 00 ---

1.

2.

3.

Table 1

Connect the set to TV Monitor.

Turn on the POWER.

Press both CH UP button on the set and the FF button on the set for more than 2 seconds.

ADDRESS and DATA will appear on TV Monitor as Fig 1 .

ADDRESS DATA

INIT 00 0E

PLAY/REC 0010

Fig. 1

4.

5.

6.

7.

8.

9.

ADDRESS is now selected and should ìblinkî. Using the SET + or - button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached.

Press ENTER to select DATA. When DATA is selected, it will ìblinkî.

Again, step through the DATA using SET + or - button until required DATA value has been selected.

Pressing ENTER will take you back to ADDRESS for further selection if necessary.

Repeat steps 4 to 7 until all data has been checked.

When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

After the data input, set to the initializing of shipping.

10.

Turn POWER on.

11.

Press both CH UP button on the set and the PLAY button on the set for more than 2 seconds.

12.

After the finishing of the initializing of shipping, the unit will turn off automatically.

The unit will now have the correct DATA for the new MEMORY IC.

C4-1

(For 2 heads model)

VHS Alignment Tape

JG001

JG001A

JG001Q

JG001T

(VN

2

S-LI6

3

)

(VN

2

S-CO1

3

)

(VN

2

S-LI6

3

H)

(VN

2

S-X6

3

)

SERVICING FIXTURES AND TOOLS

(For 4 heads model)

VHS Alignment Tape

JG001B

JG001I

JG001P

JG001S

(VN

1

S-LI6

3

)

(VN

1

S-CO1

3

)

(VN

1

S-LI6

3

H)

(VN

1

S-X6

3

)

JG002B

JG002E

Adapter

Dial Torque Gauge

JG002F

(10~90gf

• cm)

(60~600gf

• cm)

JG005 Post Adjustment

Screwdriver

Part No. SV-TG0-030-000

(small)

JG153 X Value Adjustment

Screwdriver

JG022 Master Plane JG024A Reel Disk Height

Adjustment Jig

JG100A Torque Tape

(VHT-063)

JG154 Cable Tentelometer

Ref. No.

Part No.

Parts Name

JG001 APJG001000

JG001A APJG001A00

JG001Q

JG001T

APJG001Q00

APJG001T00

VHS Alignment Tape

VHS Alignment Tape

VHS Alignment Tape

VHS Alignment Tape

JG001B APJG001B00 VHS Alignment Tape

JG001I

JG001P

APJG001I00

APJG001P00

VHS Alignment Tape

VHS Alignment Tape

JG001S APJG001S00 VHS Alignment Tape

JG002B

JG002E

JG002F

JG005

JG153

APJG002B00

APJG002E00

APJG002F00

APJG005000

APJG153000

Adapter

Dial Torque Gauge (10~90gf

• cm)

Dial Torque Gauge (60~600gf

• cm)

Post Adjustment Screwdriver

X Value Adjustment Screwdriver

JG022

JG024A

JG100A

APJG022000

APJG024A00

APJG100A00

Master Plane

Reel Disk Height Adjustment Jig

Torque Tape (VHT-063)

JG154 APJG154000 Cable

Remarks

Monoscope, 6KHz (For 2 heads model)

Color Bar, 1KHz (For 2 heads model)

Hi-Fi Audio (For 2 heads model)

X Value Adjustment (For 2 heads model)

Monoscope, 6KHz (For 4 heads model)

Color Bar, 1KHz (For 4 heads model)

Hi-Fi Audio (For 4 heads model)

X Value Adjustment (For 4 heads model)

VSR Torque, Brake Torque (S Reel/T Reel Ass'y)

Brake Torque (T Reel Ass'y)

VSR Torque, Brake Torque (S Reel)

Guide Roller Adjustment

X Value Adjustment

Reel Disk Height Adjustment

Reel Disk Height Adjustment

Playback Torque, Back Tension Torque During Playback

Used to connect the test point of SERVICE and GROUND

PREPARATION FOR SERVICING

How to use the Servicing Fixture

1.

2.

3.

While pressing the POWER button on the set for more than 2 seconds, press the CH DOWN button on the set simultaneously at the Power OFF. Although the DVD is connected, the DVD mode cannot be selected.

Short circuit between TP3001 and Ground with the cable JG154.

(The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape.)

In case of using a cassette tape, press the TAPE EJECT button to insert or eject a cassette tape.

Turn on the power and re-check the cable before checking the trouble points.

When you servicing with connection of DVD, perform the operations above step 2 to step 3.

D1-1

MECHANICAL ADJUSTMENTS

1. CONFIRMATION AND ADJUSTMENT

Read the following NOTES before starting work.

Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.)

1-1: CONFIRMATION AND ADJUSTMENT OF REEL

DISK HEIGHT

1.

2.

3.

4.

Turn on the power and set to the STOP mode.

Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 1-

1-A.

While turning the reel and confirm the following points.

Check if the surface “A” of reel disk is lower than the surface “B” of reel disk height adjustment jig (JG024A) and is higher than the surface “C”. If it is not passed, place the height adjustment washers and adjust to

10(+2, -0)mm.

Adjust the other reel in the same way.

1-2: CONFIRMATION AND ADJUSTMENT OF TENSION

POST POSITION

1.

2.

3.

Set to the PLAY mode.

Adjust the adjusting section for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis.

While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.

Standard line of Main Chassis

Tension Arm

0.5mm (Adjusting range)

Fig. 1-2-A

Adjusting section for the

Tension Arm position

Master Plane (JG022)

Reel Disk Height Adjustment Jig

(JG024A)

Tension Band

Fig. 1-1-A

Master Plane (JG022)

Reel Disk

(B)

Reel Disk Height

Adjustment Jig

(JG024A)

10(+0.2, -0)mm

(C)

Height Adjustment Washer

2.6x4.7xT0.13

2.6X4.7xT0.25

(A)

Fig. 1-1-B

The Tension Arm top will move to the inside direction of the Main Chassis.

Bend

The Tension Arm top will move to the outside direction of the Main Chassis.

Fig. 1-2-B

1-3: CONFIRMATION OF PLAYBACK TORQUE AND

BACK TENSION TORQUE DURING PLAYBACK

1.

2.

Load a video tape (T-120) recorded in standard speed mode. Set the unit to the PLAY mode.

Install the tentelometer as shown in Fig. 1-3. Confirm that the meter indicates 20

±

2gf in the beginning of playback.

USING A CASSETTE TYPE TORQUE TAPE (JG100A)

1.

2.

3.

After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode.

Confirm that the right meter of the torque tape indicates 50~90gf

• cm during playback in SP mode.

Confirm that the left meter of the torque tape indicates

25~40gf

• cm during playback in SP mode.

Tentelometer

Video Tape

P1 Post Guide Roller

Fig. 1-3

D2-1

MECHANICAL ADJUSTMENTS

1-4: CONFIRMATION OF VSR TORQUE

1.

2.

Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode.

(Refer to Fig.1-4-B)

Then, confirm that it indicates 120~180gf

• cm.

NOTE

Install the Torque Gauge on the reel disk firmly. Press the

REW button to turn the reel disk.

NOTE

If the torque is out of the range, replace the following parts.

Check item

1-4

1-5

Replacement Part

Idler Ass’y/Clutch Ass’y

S Reel side: S Reel/Tension Band/Tension

T Reel side:

Connect/Tension Arm Assíy

T Reel/T Brake Band//T Brake

Spring/T Brake Arm

1-5: CONFIRMATION OF REEL BRAKE TORQUE

(S Reel Brake) (Refer to Fig. 1-4-B)

1.

2.

3.

4.

Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller

Block is on the position of Fig. 1-4-A.

Move the Idler Ass’y from the S Reel.

Install the Torque Gauge (JG002F) and Adapter

(JG002B) on the S Reel. Turn the Torque Gauge

(JG002F) clockwise.

Then, confirm that it indicates 60~100gf

• cm.

(T Reel Brake) (Refer to Fig. 1-4-B)

1.

2.

3.

4.

Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller

Block is on the position of Fig. 1-4-A.

Move the Idler Ass’y from the T Reel.

Install the Torque Gauge (JG002E) and Adapter

(JG002B) on the T reel. Turn the Torque Gauge

(JG002E) counterclockwise.

Then, confirm that it indicates 30~50gf

• cm.

The position at

STOP mode.

Capstan DD Unit

The position at FF mode.

Stop at this position.

Pinch Roller Block

Cassette Holder Assíy

Cassette Opener

Fig. 1-4-A

2. CONFIRMATION AND ADJUSTMENT

OF TAPE RUNNING MECHANISM

Tape Running Mechanism is adjusted precisely at the factory. Adjustment is not necessary as usual. When you replace the parts of the tape running mechanism because of long term usage or failure, the confirmation and adjustment are necessary.

2-1: GUIDE ROLLER

1.

2.

3.

4.

5.

6.

7.

Playback the VHS Alignment Tape (JG001 or JG001B).

(Refer to SERVICING FIXTURE AND TOOLS)

Connect CH-1 of the oscilloscope to TP101 (Envelope) and CH-2 to TP3002 (SW Pulse).

Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center.

Trigger with SW Pulse and observe the envelope. (Refer

to Fig. 2-1-A)

When observing the envelope, adjust the Adjusting

Driver (JG005) slightly until the envelope will be flat.

Even if you press the Tracking Button, adjust so that flatness is not moved so much.

Adjust so that the A : B ratio is better than 3 : 2 as shown in Fig. 2-1-B, even if you press the Tracking Button to move the envelope (The envelope waveform will begin to decrease when you press the Tracking Button).

Adjust the PG shifter during playback.

(Refer to the ELECTRICAL ADJUSTMENTS)

NOTE

After adjustment, confirm and adjust A/C head.

(Refer to item 2-2)

Torque Gauge/Adapter

(JG002F/JG002B)

Torque Gauge/Adapter

(JG002E/JG002B)

CH-1

Envelope

(TP101)

CH-2

SW Pulse (TP3002)

CH-1

Track

CH-2

Track

Fig. 2-1-A

S Reel

Max

Entrance

A B

Exit

T Reel

Fig. 1-4-B

Max

Fig. 2-1-B

D2-2

MECHANICAL ADJUSTMENTS

2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/

CONTROL HEAD

When the Tape Running Mechanism does not work well, adjust the following items.

1.

2.

3.

4.

Playback the VHS Alignment Tape (JG001 or JG001B).

(Refer to SERVICING FIXTURE AND TOOLS)

Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 2-

2-A.

a)

When the reflected picture is distorted, turn the screw b)

(1) clockwise until the distortion is disappeared.

When the reflected picture is not distorted, turn the screw (1) counterclockwise until little distortion is appeared, then adjust the a).

Turn the screw (2) to set the audio level to maximum.

Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw (3) to adjust the height. Then, adjust the 1~3 again.

2-3: TAPE RUNNING ADJUSTMENT

(X VALUE ADJUSTMENT)

1.

2.

3.

4.

5.

6.

7.

8.

Confirm and adjust the height of the Reel Disk.

(Refer to item 1-1)

Confirm and adjust the position of the Tension Post.

(Refer to item 1-2)

Adjust the Guide Roller. (Refer to item 2-1)

Confirm and adjust the Audio/Control Head.

(Refer to item 2-2)

Connect CH-1 of the oscilloscope to TP3002, CH-2 to

TP101 and CH-3 to HOT side of Audio Out Jack.

Playback the VHS Alignment Tape (JG001S or JG001T).

(Refer to SERVICING FIXTURE AND TOOLS)

Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center.

Set the X Value adjustment driver (JG153) to the (4) of

Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between

Audio and Envelope waveform becomes (1) or (2) of Fig.

2-3.

Audio/Control Head

Reflected picture of

Stamp Mark

P4 Cap

Envelope

CH-3

Audio

(1)

(2)

Fig. 2-3

(3)

(2)

Stamp Mark

Audio/Control Head

Tape

Audio/Control Head

(1)

(4)

Fig. 2-2-A

Fig. 2-2-B

2-4: CONFIRM HI-FI AUDIO (Hi-Fi model only)

1.

2.

3.

4.

5.

6.

7.

Connect CH-1 of the oscilloscope to TP101 and CH-2 to the Hi-Fi Audio Out Jack.

Playback the VHS Alignment Tape (JG001P or JG001Q).

(Refer to SERVICING FIXTURE AND TOOLS)

Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center.

Press the Tracking Up button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to

MONO (6KHz).

Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center.

Press the Tracking Down button and count number of steps which the audio output is changed from Hi-Fi

(10KHz) to MONO (6KHz).

If the difference are more than 3 steps, set the X Value adjustment driver (JG153) to (4) of Fig. 2-2-B. Change the X Value and adjust it so that the value becomes within 2 steps.

0.25

±

0.05mm

Fig. 2-2-C

D2-3

MECHANICAL ADJUSTMENTS

3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE

4

5

3

2

1

6

7

10 9

1. Tension Connect

2. Tension Arm

3. Guide Roller

4. Audio/Control Head

5. X value adjustment driver hole

8

6.

7.

P4 Post

T Brake Spring

8.

T Reel

9.

10.

S Reel

Adjusting section for the Tension Arm position

D2-4

ELECTRICAL ADJUSTMENTS

Read and perform this adjustment when repairing the circuits or replacing electrical parts or PCB assemblies.

1. BASIC ADJUSTMENT

CAUTION

When you exchange IC and Transistor for a heat sink, apply the silicon grease (YG6260M) on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)

1-1: PG SHIFTER

CONDITIONS

MODE-PLAYBACK

Input Signal-Alignment Tape (JG001P)

INSTRUCTIONS

1.

2.

3.

4.

Connect CH-1 on the oscilloscope to TP3002 and CH-2 to TP8001.

Playback the alignment tape. (JG001P)

Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center.

Press both CH UP button on the set and the STOP button on the set for more than 2 seconds.

CH-2

6.5H

6.5H

CH-1

Fig. 1-1-A

CH-2

CH-1

Fig. 1-1-B

D3-1

ELECTRICAL ADJUSTMENTS

2. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

J8002 J8001

VCR PCB

TP8001

CP102

TP3001 S501

S502

CP103

FE HEAD

AC HEAD

TP101

TP3002

V651

CD501

AC IN

CD8002

CP8102

CP501

CP651

DVD DECK

CP4002

CP2601

CP2603

CP2602

DVD PCB

CD2001

CD681

CP681

OPERATION PCB

D3-2

DVD BLOCK DIAGRAM

DVD LOADER

DM II

A, B, C, D, E, F

Pick up

Loading

Motor

Spindle/

Sled

Motor

RF

CD, DVD, LD

READ

CHANNEL

IC2601

ZR36707TQC

RFA_SDEN, DATA, SCLK

AAF_CE, FE, TE, PI

FNN, FNP

VBIASS0, S1

DEFECT, LINK, MIRR, LDON

SPDL+/–

Dual OP-AMP

IC2602

BA10358F-E2

SPDL_SENS

HOME, TIN SW, TOUT SW

TR+/–, FO+/–

SPDL+/–, SLED+/–

Motor Driver

IC2301

LA6560

SPINDLE, SLED_PWM

TRACK, FOCUS_DAC

ADC IN 5, 6, 7

S MUTE

E-1

FLASH 8M

IC4007

SST39VF800A-

70-4C-EK

64M SDRAM

IC4005

M12L64164A-7T

HD0~HD15,

HA0~HA20

SDA0~SDA11

SDD0~SDD15

MPEG/MICON

IC4001

ZR36762

REG+1.8V

IC4003

PQ070XZ01ZP

EEPROM

IC4002

AT24C04N-10SI-

2.7

ASDATA0

AMCLK

ABCLK

ALRCLK

STEREO DAC

IC7301

PCM1742

KE/2K

DAC

Y

C

Y/C SEPA

J8102

3

4

A, B, C

VIDEO OUT SW

SW8101

SK42H0IG9A

Y

U

V

AUDIO AMP

IC8101

NJM4580M(TE1)

DVD AUDIO L

DVD AUDIO R

AUDIO MUTE

Q8101~Q8105

5

3

2

YUV OUT

J8103

SPDIF

DIGITAL AUDIO

DRIVER

Q8107

OPTICAL

OS8101

DAC D

3

2

DVD AUDIO

OUT

J8101

5

VCR BLOCK

TX

RX

P.CON+3.3V

P.CON+5V

P.CON+9V

P.CON+12V

AT+5V

CP4002

CP8102

DVD RESET

DVD VIDEO

DVD AUDIO L

DVD AUDIO R

SYSTEM MUTE

E-2

E-3

CYL

3

4

5

CP101

1

EP/LP-CH2 (L)

2

EP/LP_COM

EP/LP-CH1 (R)

SP-CH2 (L)

SP_COM

6

SP-CH1 (R)

7

8

9

HF2 (L)

HF_COM

HF1 (R)

HI-FI/DEMODU

LATOR

HF1

HF_COM

HF2

FE HEAD

CP103

1 FE HEAD (HOT)

2

FE HEAD (GND)

HEAD

AUDIO

CONTROL

CP102

5

6

AUDIO PB

AUDIO REC

4

3

CTL+

CTL-

1 AE HEAD(-)

2

AE HEAD(+)

Y/C/AUDIO/CCD/HEAD AMP BLOCK DIAGRAM

X101

3.579545M Hz

Y/C/AUDIO/CCD/HEAD AMP IC

IC101

LA71206M-MPB

50 49

Q109

BUFFER

41 43

39

37

Q107

BUFFER

67

66

65

72

73

74

9

7

8

6

L

L

H

H

H.SW

H.SW

REC AMP

H

H.AMP

SW

L

AUTO BIAS

P

PB

PB.EE

FM

AGC

PB

VX01

TIMMING

AGC

AMP

PULL

DRIVER

REC

FM-EQ

KIL

C-LPF

FM

MOD

OUT

CCD

WC

DC

CLAMP

NL

EMPHA

DETAL

ENH

V/I

CONV

Y-LPF

P

R

R

GCA

B-UP

AMP

Main

CONV

3.58M

BPF2

R

P

ACC

AMP

P

DELAY

FM-EQ

PHASE-EQ

EQ

AMP

DOUBLE

LIM

P

MUTE

R

KIL

B.D.

FM

DEM

R

ALC

DET

3.58M

BPF1

PB

AMP

LINE

AMP

LPF

ALC

SUB

LPF

V-AGC

YNR/

P

R

COMB

N.L.

DEEM

SERIAL

DECODER

CLAMP

VCA

CLAMP

55

54

53

22

21

36

34

P

SYNC

SEP

NC1

Y/C MIX

1/2

P

H.AMP SW/

AUDIO

MUTE

58

C ROT

RF SW IN

57

FBC

R

ENV DET

59

R

Chara

INS.

6dB

COMP

OUT

60

24

25

26

11

5 4

3

2

10

80 78 76

32 30 28

COIL, BIAS OSC

L101

5

2

Q105

BIAS CTL

3

Q104

BIAS OSC

4 1

Q101, Q102

AUDIO PB SW

Q103

SW

4FSC

Y/C_CS

Y/C_DATA

Y/C_CLK

SYSCON

Q106

BUFFER

H. AMP_SW

C. ROTARY

H. SW

AUDIO_MUTE-H

SYSCON

ENV. DET

COMP

DUMMY_V. SYNC

C.SYNC

Y/C_VIDEO_OUT

FSC

FRONT_V_IN

TU/REAR_V_IN

TUNER/JACK

TO_NORMAL_A

FROM_NORMAL_A

FSC

DVD V OUT

P. CON + 5V

HI-FI/DEMODU

LATOR

DVD

POWER

V.REC_ST-H

CTL+

CTL-

SYSCON

E-4

E-5

SYSCON BLOCK DIAGRAM

SYSCON/TIMER/SERVO

IC3001 OEC0138B

POWER

TUNER/JACK

OPERATION/

DISPLAY

POWER

DVD_POWER_CTL

VCR_POWER_ON-L

POWER_FAIL

RX

1G/VCR/T-REC_LED

SEG_5

SEG_1

VCR_LED

DVD_LED

2G/DUB/REC_LED

KEY-B

KEY-A

REM_IN

BOT SENSOR

Q3008

CAPSTAN

DD UNIT

CP3001

11 CYL FG/PG

12

CYL DRIVE

10 LDM CTL

5

I LIMIT

9

CAP CTL

1

CAP FG

4

CAP.M F/R

2 CAP VCO

8 LD/CY_VCO

AT+12.6V

P.CON +5V

TX

DVD RESET

CENT LED

D3001

MS_SEN B

Q3004

AT 5.2V

EOT SENSOR

Q3006

REEL SENS

Q3001

2

4

2

3

1

4

2

3

1

3

1

4

2

4

X3001

10MHz

X3002

32.768KHz

POWER

1

3

Q3005

P.CON+5V

REEL SENS

Q3002

MS_SEN A

45

DVD_POWER_CTL

41 POWER ON-L

37

POWER FAIL

65

80

RX

OSC 2

78 OSC 1

64

75

TX

X2

76 X1

44

DVD/RESET

48 1G/VCR/T-REC LED

63 SEG5

55

SEG1

47

VCR LED

46

49

DVD LED

2G/DUB/REC LED

29 KEY-B

30 KEY-A

43

REM IN

25

BOT-H

26

EOT-H

39

38

REEL-T

REEL-S

103

CYL SPEED UP

104

DFG/PG

107

DRUM PWM

97

LDM CTL

102

CAP FULL

108 CAP PWM

84

CAP LIMIT

9

CAP FG

98 CAP FWD-L

28

MS SEN-A

27 MS SEN-B

HIFI ENV

32

HIFI H.SW 106

ST SELECT

31

4 FSC IN

22

C.SYNC 111

DUMMY V.SYNC

109

VIDEO H.SW

105

C.ROTARY

99

Y/C CS

93

AUDIO MUTE-H

95

H.AMP SW 100

V.REC ST-H 96

V ENV

24

CTL(+)

3

CTL(-)

4

Y/C DATA

Y/C CLK

54

53

COMP 101

AV SW1

92

CV IN1

16

CV IN2

17

POWER MUTE-L

87

AFT S.CURVE

33

CV OUT

19

VCR-H

86

IIC CLK 61

IIC SDA

62

VIDEO MUTE H

40

SYS_MUTE 88

RF_CH_SW

94

TAB SW

35

/RESET 77

SEG 10

SEG 9

SEG 8

73

71

68

SEG 7 67

SEG 6 66

3G/TV/VCR LED

4G/TIME SHIFT LED

50

51

5G/CS/BS LED 52

SEG 2

58

SEG 3

59

SEG 4 60

TAB SW

IC3003

PST3231NR

1

SYSTEM

RESET

2

SW_V_ OUT

POWER_MUTE-L

AFT-S.CURVE

VIDEO_OUT

TV/VCR

SCL

SDA

VIDEO_MUTE-H

SYS_MUTE

RF_CH_SW

6

SCL

5

SDA

EEP ROM

IC3099

AT24C04N-10SI-2.7

AT+5V

SEG 10

SEG 9

SEG 8

SEG 7

SEG 6

3G/TV/VCR_LED

4G/VSC_LED

5G/CS/BS_LED

SEG 2

SEG 3

SEG 4

V.REC_ST-H

AUDIO_MUTE-H

SCL

SDA

HIFI_ENV.DET

HIFI_H.SW

ST_SELECT

4FSC

C.SYNC

DUMMY_V.SYNC

H.SW

C.ROTARY

Y/C CS

AUDIO_MUTE-H

H.AMP_SW

V.REC_ST-H

ENV.DET

CTL+

CTL-

Y/C_DATA

Y/C_CLK

COMP

AV_SW1

HI-FI/

DEMODULATOR

Y/C/AUDIO/

CCD/HEAD AMP

TUNER/JACK

POWER

OPERATION/

DISPLAY

E-6

E-7

STOP

REC/OTR

FF/CUE

PLAY

REW/REV

OPEN CLOSE

OPERATION/DISPLAY BLOCK DIAGRAM

V651 CO2D0M3-A

14 15

13 12 11 10 8

9 7 5 4 6 2 1 3

Q651

5G SW

Q653

SEG9 SW

Q652

SEG10 SW

Q654

4G SW

Q655

SEG8 SW

Q656

SEG7 SW

Q657

SEG6 SW

Q659

3G SW

Q658

SEG5 SW

Q660

SEG4 SW

Q661

2G SW

Q662

SEG3 SW

Q663

SEG2 SW

Q664

SEG1 SW

Q665

1G SW

VCR EJECT

POWER

VCR/DVD

CH UP

CH DOWN

CP681

KEY-A

KEY-B

DVD LED

2

1

5

DVD LED

D685

CP651

2

1

5

OS651

1

Q666

DVD LED SW

VCR LED

D651

5G/CS/BS_LED

SEG10

SEG9

4G/VSC_LED

SEG8

SEG7

SEG6

SEG5

3G/TV/VCR_LED

SEG4

2G/DUB/REC_LED

SEG3

SEG2

SEG1

1G/VCR/T-REC_LED

DVD_LED

VCR_LED

SYSCON

KEY-A

KEY-B

REM_IN

AT+5.2V

SYSCON

POWER

E-8

Y/C/AUDIO/CCD

/HEAD AMP

HF1

HF2

HF_COM

FSC

FROM_NORMAL_A

TO_NORMAL_A

POWER

P.CON+5V

P.CON+12V

E-9

HI-FI/DEMODULATOR BLOCK DIAGRAM

25

40

51

58

HI-FI/AUDIO/H.AMP/DEM IC

IC701

AN3663FBP

22

AMP

24 AMP

21

AGC

L/R

MIX

OUTPUT

SW

REC

LPF

VCO

INPUT SW

AMP

AMP

RFC

1

10

15

2

4

3

53

57

59

PNR

45

62

61

VCO-FO

ADJ

LOGIC

BPF

FM LIM

DBX

NOISE

REDUCTION

DEM

BLOCK

48

30

LOGIC

29

28

27

36

42

43

56

DVD_A_OUT-R

DVD_A_OUT-L

FRONT_A_IN-R

FRONT_A_IN-L

AUDIO_OUT_R

AUDIO_OUT_L

RF_CONV_A_OUT

TUNER/JACK

SIF OUT

V. REC_ST-H

HIFI_ENV. DET

HIFI_H.SW

AUDIO_MUTE-H

SCL

SDA

ST_SELECT

SYSCON

E-10

E-11

SYSCON

VIDEO_MUTE_H

VIDEO_OUT

SW_V_OUT

POWER

P. CON+12V

+32V

P.CON+5V

TU301

3

5

1

15

8

4

10

11

14

2

17

12

TUNER/JACK BLOCK DIAGRAM

REAR OUT JACK

J8001

FRONT AV JACK

VIDEO

AUDIO L

J8003

J8004

2 3 5 2 2

AUDIO R

J8005

2

3

Q8004

BUFFER

Q8003

VIDEO

MUTE SW

Q301

MUTE SW

Q8005

MUTE SW

Q8006

MUTE SW

Q8007

MUTE SW

6

1

4

2

Vcc

3

AV SW

IC8005

MM1501XNRE

FSC

FRONT_V_IN

Y/C VIDEO OUT

TU/REAR_V_IN

FRONT_A_IN_R

FRONT_A_IN_L

AUDIO_OUT_R

AUDIO_OUT_L

DVD_A_OUT_R

DVD_A_OUT_L

RF_CONV_A_OUT

SIF_OUT

POWER_MUTE_L

TV/VCR

SCL

SDA

Y/C/AUDIO/CCD

HEAD AMP

HI-FI/

DEMODULATOR

SYSCON

RF_CH_SW

AFT-S. CURVE

AV SW1

SYS_MUTE

DVD_RESET

DVD_RESET

SYS_MUTE

DVD_VIDEO

DVD_AUDIO_L

DVD_AUDIO_R

CP8002

5

3

7

6

1

E-12

E-13

AC IN

L501

D505, D506

D502, D503

T501

2

7

11

4

13

14

15

Q501

SW.

Q502

CONTROL

IC503

PS2561L1-1-V(W)

PHOTO

COUPLER

IC501

KIA431

VOLTAGE

CTL. IC

3 1

POWER BLOCK DIAGRAM

Q508

3.3V CTL

Q510

P.CON+12V

SW

Q509

P.CON SW

Q511

3.3V OUT

Q507

3.3V CTL

Q506

M-CON

POWER SW.

Q530

PROTECT

Q531

PROTECT

Q504

M-CON+5V

SW.

Q503

P.CON+5V

SW.

Q513

POWER FAIL

SW.

Q514

POWER FAIL

SW.

9VREG

IC502

KIA78R09API

4

1

2

Q505

P.CON 5V

SW.

AT+12.6V

P.CON+12V

SYSCON

TUNER/JACK

VCR POWER ON-L SYSCON

AT+5.2V

P.CON+5V

OPERATION/DISPLAY

AT+5V (M-CON)

SYSCON

POWER FAIL

DVD POWER CTL

P.CON+5V

P.CON+5V

P.CON+12V

P.CON+5V

AT+5.2V

+32V

RX

TX

TX

RX

P.CON+3.3V

P.CON+3.3V

P.CON+5V

P.CON+9V A

P.CON+9V A

P.CON+12V

AT+5V

CP501

1

2

3

8

9

4

7

11

12

Y/C/AUDIO/

CCD/HEAD AMP

HI-FI/

DEMODULATOR

TUNER/JACK

SYSCON

DVD

E-14

F-1

DVD (TOP SIDE)

R2310

R2307

R2312

C2304

W863

C2310

IC2602

W876

R2628

R2630

R2631

R2629

R2627

R2632

R2625

R2626

HS2301

R2620 R2647

R2624

R2623

Q2603

Q2604

R2619 R2621

Q2605

R2622

R2612

R2613

C2643

49

C2644

IC2601

33

C2619

C2614

R2602

C2613

R2607

R2608

C2620

R2609

C2622

R2648

R2645

R2646

R2605

C2655

C2646

C2612

C2610

W835

1 17

R2601

W827

R2318

R2306

C4084

C2634 C2648

C2608

C2636

C2637

B2601

C2638

C2639

R2615

R2616

B2602

R2618

R2617

C2640

C2641

C4051

C4063

B4008

C4047

C4018

53

W854

R4040

1

R4052

R4051

W857

R4050

R4049

C4067

C4011

C4083

C4068

C4009

R4032

R4034

IC4003

C4069

C4070

C4071

R4048 C4021

R4008

IC4001

R4043

R4044

C4041

C4046

C4045

C4023

C4040

C4025

105 157

C4098

C4094

R4027

R4025

R4026

R4035

R4031

C4093

C7311

IC4002

R4047

R4021

R4020

R4019

C4078

C4026

C4031

R4024

C4029

R8129

C7310

C8106

R8108

IC7301

R8106

R7307

C7306 R8104

R8103

C8102

C7304

C7303

C7301

R7306

R8102 R8107

C7308

C7305

R8101

R8105

C8105

C8101

R8128

R8110

IC8101

R8109

C8118

C8111

C8114

W855

W860

C7302

C8146

C8138

W817

C8112

C8113

L8101

C8134

C8144

C8139

C8140

L8102

C8135

C4079

C4035

R4042

R4012

X4001

C8115

R4001

W833

C8119

W820

C8137

L8104

C8141

C8122

R8118

W865

C8123

R8123

C8120

R8120

R8119

C8145

W818

W819

L8103

C8136

C8124

R8130

J8102

SW8101

J8103

OS8101

J8101

PRINTED CIRCUIT BOARDS

DVD (BOTTOM SIDE)

C8143

C8142

R8151

C8148

C8149

C8147

C8121

C8125

B8102

R8137

C8126

R8136

R8133_1

C8129

B8103

R8134

R8135

B7301

C8110

C8107

R8114

R8115

R8112

R8116

R8117

R4016

R4045

R8122

R8124

R4036

R4037

R4038

R4039

C4038

W806

R4018

R4023

R8113

W873

C4037

C4044

C4050

B4007

C4095

C4077

R4014

C4030

C4028

C4027 C4033

W832

R4054

R4053

C4017

C4016

C4020

C4024

C4019

C4081

R2649

C4096

C4032

C4013

C4014 C4010 C4008

C4005

C4088

C4089

C4090

C4002

C4003

C4076

C4022

C4075

B4002

C4073

B4003

C4082

B4004

C4074

B4001

B4006

C4072

B4005

C4012

C4015

R2650

C4036

C2626

C2627

C2632

R2611

W807

C2642

C2609

C2611

C2615

C2623

R2653

R2652

C2647

C4097

W810

C2645

R2303

C2302

B2603

C2311

R2331

W808

R2337

R2330

R2304

C2307

C2308

C2303

C2657

C2658

C2659

C2660

B2604

R2329

C2312

R2328

R2325

C2306

C2301

R2301

B2605

C4066

R2327

R2326

R2322

R2321

R2316

C2309

R2334

R2324

W805

C4065

R2319

W864

R2313

C2305

C4080

R2314

R2308

C4087

R2305

W862

R2309

C4092

C4091

W802

W801

F-2

F-3

PRINTED CIRCUIT BOARDS

VCR (INSERTED PARTS)

SOLDER SIDE

V651

W189

W187

W839

W840

W101

W100

W033

CP651

W185

Q510

C3023

W031

W184

W183

W256

R3011

R3019

W093

W089

C3021

W092

W094

W091

W114

W112

W838

W837

W023

R3050

Q3005

W029

W021

W019

W291

W022

W028

W020

W052

W051

W050

W290

C8032

C8031

W111

C3045

C8053

W206

TP3002

TP701

TP101

W248

W272

W273

W249

W106

W105

W104

W138

W136

W134

W133

Q3006

W132

W131

W269

W268

W267

W217

L106_1 C140

W129

CP103

W260

W259

W258

W265

W277

W276

W845

W262

W279

W278

C739

W264

W263

W261

L703

C704_1

C756_1

C703

C754

C750_1

C747

C752_1

C743_1

C735

C737

C740

W862

C731

C741_1

C146_1

W306

C148_1

L105_1

W863

C152

C151

W230

R123

X101

C142_1

L107

C137_1

C134

C138

C759

C135

W158

C705

W118

C758_1

C742_1

C136

C702_1

C132

C706_1

C163_1

C124_1

C708_1

W287

W275

C709

W274

C711

C714_1

W288

W229

C761

W864

CP101

C103_1

C119_1

R109

C105_1

C110_1

C115_1

W286

W859

Q105

C720 C727_1

Q104

W126

W809

W123

W116

C131_1

W156

W155

W296

W152

R140

W146

W142

C123

L101

W124

W121

C174

C120_1

W157

W297

W143

W122

W151

W150

W148

W135

W130

W128

W127

W125

W120

W119

W117

W160

W147

W144

W141

W161

W159

C3029

W070

W069

W067

W065

W145

L301

C8003

C728

C112

L102

C8042

C104

C8040

CP102

L3003

W058

L103

CP3001

L3002_1

R8059

W063

W062

W085

D8008

W083

C8075

W081

W080

W079

W078

W077

C309

C315

C318

J8002 J8001

C313

L8008

D8003

W075

W074

W073

W162

W072

TP8001 C8013

C8015

Q8004

W064

W818

W084

W082

W076

TP3001

W036

W035

W034

W061

W060

W059

D3007

W048

W294

W293

W043

C3013

W041

W039

W038

W302

C3052

W046

W040

W042

R553

R554

W037

C3032

C3016

W303

C504_1

Q3008

R3015

W057

R3038

W055

C3033_1

W054

W816

W071

W849

R514

W056

R517

D523

Q503

R541

W295

W066

W876

W873

W308

V_A_

D526

L501

FH502

IC503

F501

IC501

D530

C528

D531

R524

Q502

D504

C509

R504

Q504

D513

Q505

C505_1

C521

C514

C506_1

W001

C510_1

R528

W298

R527

IC502

Q511

D539 C530_1

D538

W014

W844

W806

W832

W013

C501_1

D656

C540

C502

FH501

T501

D524

R508

W016

D506

W871

C511_2

S502

S501

R501

C525

B501

HS501

R502

B502

Q501

D512

C516

OPERATION

SOLDER SIDE

SW690

SW686

R690

R685

SW689

R686

R688

SW685

R687

SW687

SW688

R689

CP681

F-4

F-5

Q530

R510

Q531

R530

Q507

Q508

Q509

Q506

Q514

Q513

R525

PRINTED CIRCUIT BORDS

VCR (CHIP MONTED PARTS)

SOLDER SIDE

Q8003

IC8002

Q666

R3046

Q8007

R108

R3003

R3056

R3035

R3031

Q3007

Q3003

R3053

R3030

R3027

R3022

R3012

1

R3057

29

IC3001

R3087

57

Q664

R509

Q651

R675

Q665

Q661

Q654

Q659

Q662

Q663

Q660

Q655

Q658

Q657

Q656

Q653

Q652

R668

85

IC3003

R3051

R3037

R3045

Q101

Q102

Q103

R110

1

21

IC101

41

R127

R126

61

R121

Q106

R141

R143

R122

Q107

Q109

R133

R132

IC3099_1

R3006

IC8005

Q8005

R8056

R8015

R8014

R8017

Q8006

33

R710

R714

R707

17

IC701

49

R706

R716

1

R711

R703

R304

R305

Q301

F-5

8

7

A

6

5

4

3

2

FROM/TO MEMORY

D_GND

P.CON+3.3V

HA17

HA18

HA19

HA20

HD0

HD1

HD2

HA9

HA10

HA11

HA12

HA13

HA14

HA15

HA16

HA0

HA1

HA2

HA3

HA4

HA5

HA6

HA7

HA8

HD3

HD4

HD5

HD6

HD7

HD8

HD9

HD10

HD11

HD12

HD13

HD14

HD15

MEMCS0

RD

WR

SD_D7

SD_D8

SD_D9

SD_D10

SD_D11

SD_D12

SD_D13

SD_D14

SD_D15

RAMCS0#

RAMCS1#

RAMRAS#

RAMCAS#

SD_BA0

RAMDQM

RAMWE#

RAMCLK

SD_A0

SD_A1

SD_A2

SD_A3

SD_A4

SD_A5

SD_A6

SD_A7

SD_A8

SD_A9

SD_A10

SD_A11

SD_D0

SD_D1

SD_D2

SD_D3

SD_D4

SD_D5

SD_D6

1

G-1

A

B C D E

MPEG/MICON SCHEMATIC DIAGRAM

(DVD PCB)

F G

DUPTD1

DUPRD1

DUPTD0

DUPRD0

P.CON+5V

W832

C4088

0.01 B

C4089

0.01 B

C4090

0.01 B

W833

R4002

R4003

R4004

R4005

V_GND

GND

W831

75 +-1%

75 +-1%

82 +-1%

75 +-1%

HD11

HD3

HA19

HD10

HA18

HD2

HA17

HD9

HA7

HD1

HA6

HD8

HA5

HD0

HA4

RD

HA3

HA2

MEMCS0

HA1

HA0

HA10

HD14

HA9

HD6

HA8

HD13

HD5

HA20

HD12

WR

HD4

HA15

HA16

HA14

HA13

HA12

HD15

HA11

HD7

+1.8V

+3.3V

B4002

FCM2012H-102T04 B4003

B4001

FCM2012H-102T04

FCM2012H-102T04

B4004

B4005

FCM2012H-102T04

FCM2012H-102T04

C4008 0.1 F

C4010 0.1 F

C4013 0.1 F

C4014

C4016

C4017

0.1 F

0.1 F

0.1 F

2.0

0

3.3

0.6

3.3

2.6

1.8

2.7

2.9

0

2.6

1.9

0

0

2.1

0

0

0

3.3

NC

3.3

3.3

3.0

3.0

3.0

3.3

3.3

0.5

0

3.1

3.2

3.3

0

3.3

0.4

3.3

3.1

0

0

0

0.6

2.7

2.7

0.6

0.5

0

0.6

0

0

0

0.4

5.5

3.3

208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157

SSCRXD

MEMCS(1)

DUPTD1

DUPRD1

VDDP

MEMAD(15)

MEMAD(16)

MEMAD(14)

VDD-IP

DUPTD0

DUPRD0

GNDP

MEMAD(13)

MEMAD(12)

MEMDA(15)

MEMAD(11)

MEMDA(7)

GNDP

MEMAD(10)

MEMDA(14)

MEMAD(9)

MEMDA(6)

MEMAD(8)

MEMDA(13)

208

207

206

205

SSCTXD

SSCCLK

SPINDLEPULSE

SLEDPULSE

160

159

158

157

VDDDAC

CVBS/C

CVBS/G/Y

GNDDACD

IDGPCI/O(3)

GPCI/O(34)

ICGPCI/O(5)

GPCI/O(33)

ICGPCI/O(4)

GPCI/O(32)

VDDP

GCLKA

GCLKP

XO

MEMDA(5)

MEMAD(20)

VDDP

MEMDA(12)

MEMWR#

MEMDA(4)

VDDC

MEMDA(11)

VDDA

RESET#

GNDA

IDGPCI/O(2)

GPCI/O(31)

VID(0)

VID(1)

VID(2)

VID(3)

V SW

MEMDA(3)

MEMAD(19)

GNDC

MEMDA(10)

MEMAD(18)

MPEG/MICON IC

IC4001

ZR36762

D1 2

D1 1

VID(7)

VDDP

GNDP

MEMDA(2)

MEMAD(17)

MEMDA(9)

MEMAD(7)

MEMDA(1)

MEMAD(6)

MEMDA(8)

MEMAD(5)

VDDP

MEMDA(0)

MEMAD(4)

MEMRD#

MEMAD(3)

MEMAD(2)

MEMCS(0)#

MEMAD(1)

MEMAD(0)

53

54

55

56

RAMADD(4)

RAMADD(3)

RAMADD(5)

RAMADD(2)

100 RAMDAT(14)

101

102

103

104

GNDP

RAMDAT(1)

RAMDAT(15)

RAMDAT(0)

ALRCLK

GPAI/O

AOUT(0)

AOUT(1)

AOUT(2)

SPDIF

IDGPCI/O(0)

ICGPCI/O(0)

GNDP

VDD-IP

VDDP

GNDP

GPCI/O(20)

VDDP

53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

100 101 102 103 104

STBY-L

GNDP

HSYNC

VDDC

VSYNC

GNDC

AIN

VDDP-A2

AMCLK

GNDP-A2

ABCLK

0

0

1.8

3.3

0

5.0

0

0

3.3

3.3

3.3

0

3.3

3.3

3.3

3.3

3.3

0

3.3

5.0

0

3.3

0

3.3

5.1

3.3

3.3

3.3

0

0

3.1

3.3

0

1.6

3.3

0

3.3

3.3

1.7

0

1.7

1.6

0

0

NC

0

0

1.6

0

NC

0

0

NC

0

3.3

TRAY_OPEN

TRAY_CLOSE

1

R4042

DJTDO

DJTDI

DJTMS

ICETCK

ICETDO

ICETDI

A_MUTE

R4024

4.7K

68

HOME

C4033

R4019

R4020

R4021

R4047

TP4010

TP4014

C4030 0.1 F

C4031 0.01 B

C4026 0.1 F

0.1 F

C4032

TP4012

C4096

TP4013

C4027 0.1

F

X4001

100BT02701

27MHz

C4028 0.1 F

0.001

B

0.001

B

C4035

22P CH

33

33

33

33

C4029 0.1 F

IAMCLK

IABCLK

IALRCLK

ASDATA1

ASDATA2

TP4015

TP4016

R4014 4.7K

R4016

RESET

TP4004

100

C4081 0.1 F

TP4006

HOME

LDON

ML

MC

MD

TP4005

TP4007

V_SW

I2CDAT

I2CCLK

R4025 220

R4026

R4027

AMCLK

100

100

ABCLK

ALRCLK

ASDATA0

SPDIF

DUPTD1

DUPRD1

DUPTD0

DUPRD0

VR_SEL

TOUT_SW

TIN_SW

SMUTE

I2CCLK

I2CDAT

TP4008

TP4009

5

SDA

GND

4

3.2

0

R4031 4.7K

R4035 4.7K

6

3.2

SCL

NC

3

0

7

0

WP

NC

2

0

8

VCC

3.3

NC

1

0

IC4003

REG+1.8V IC

PQ070XZ01ZP

3.3

V_IN V_C V_OUT V_ADJ

6

1 2 3 4

3.3

1.9

1.2

0

GND

5

P.CON+3.3V

B4006

FCM2012H-102T04

TP4003

DUPRD1

DUPTD1

P.CON+3.3V

P.CON+5V

D_GND

P.CON+A5V

L4001

2.2uH

0305

P.CON+9V

M_GND

W802

W801

P.CON+12V

AT+5V

W827

NC

R4053

1K

BOOTSEL2

NC

R4054

1K

BOOTSEL1

FROM/TO AUDIO/VIDEO

DAC_VIDEO_C

DAC_VIDEO_B

DAC_VIDEO_D

DAC_VIDEO_A

ASDATA0

ABCLK

ALRCLK

AMCLK

MD

MC

ML

SPDIF

V_SW

RESET

AT+5V

P.CON+12V

P.CON+3.3V

P.CON+A5V

P.CON+5V

GND

D_GND

FROM/TO RF AMP/DSP

HOME

SPDL_SENS

TOUT_SW

TIN_SW

RFA_SDEN

RFA_DATA

RFA_SCLK

AAF_CE

AAF_FE

AAF_TE

AAF_PI

VR_SEL

FNN

FNP

VBIASS0

VBIASS1

DEFECT

LINK

MIRR

LDON

SMUTE

TRACK_DAC

FOCUS_DAC

SPINDLE_PWM

SLED_PWM

P.CON+A5V

P.CON+3.3V

P.CON+9V

P.CON+5V

ADCIN_7

ADCIN_6

ADCIN_5

D_GND

M_GND

GND

H

3

FROM/TO POWER

CP4002 (CP501)

A2001WV2-12P

TX

RX

1

2

P.CON+3.3V

P.CON+3.3V

GND 5

6

3

4

GND

P.CON+5V

P.CON+9V A

7

8

9 P.CON+9V A

MOTOR GND

P.CON+12V

AT+5V

10

11

12

2

PCB130

VMC298

8

7

6

5

4

1

DIGITAL AUDIO SIGNAL(PB)

B C

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

D

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

E F G H

G-2

4

3

2

1

G-3

A

6

5

8

7

A B C D E

MEMORY SCHEMATIC DIAGRAM

(DVD PCB)

F

FROM/TO MPEG/MICON

HA12

HA13

HA14

HA15

HA16

HA17

HA18

HA19

HA4

HA5

HA6

HA7

HA8

HA9

HA10

HA11

SD_D13

SD_D14

SD_D15

RAMCS0#

RAMCS1#

RAMRAS#

RAMCAS#

SD_BA0

RAMDQM

RAMWE#

RAMCLK

HA0

HA1

HA2

HA3

SD_A9

SD_A10

SD_A11

SD_D0

SD_D1

SD_D2

SD_D3

SD_D4

SD_D5

SD_D6

SD_D7

SD_D8

SD_D9

SD_D10

SD_D11

SD_D12

SD_A0

SD_A1

SD_A2

SD_A3

SD_A4

SD_A5

SD_A6

SD_A7

SD_A8

HA20

HD0

HD1

HD2

HD3

HD4

HD5

HD6

HD7

HD8

HD9

HD10

HD11

HD12

HD13

HD14

HD15

MEMCS0

RD

WR

P.CON+3.3V

D_GND

FROM AUDIO/VIDEO

RESET

B4007

FCM2012H-102T04

B4008

FCM2012H-102T04

HA16

C4064

0.1 F

HD6

HD13

HD5

HD12

HD4

HD15

HD7

HD14

HD9

HD1

HD8

HD11

HD3

HD10

HD2

HD0

RD

C4062

0.1 F

MEMCS0

HA0

W854

1.2

3.3

0.7

1.9

1.3

1.2

0.6

0.7

0.8

1.6

3.3

1.6

1.6

1.3

1.2

1.4

1.4

0.9

1.6

2.6

0

2.6

2.5

0

A16

VCCQ

VSS

DQ15

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12

DQ4

VDD

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

DE#

VSS

FLASH IC

IC4007

SST39VF800A-70-4C-EK 8M

A15

1.7

HA15

A14

A3

1.0

1.7

HA14

A13

A4

0.8

1.3

HA13

A12

A6

1.5

1.6

HA12

A11

A7

2.5

1.4

HA11

A10

1.3

HA10

A9

A17

1.6

0.7

HA9

A8

1.5

HA8

0

A19

HA19

0

A20

A18

1.6

HA20

WE#

3.3

0

RP#

0.1

W828

VPP

WP#

0.1

W829

R4041

4.7K

0

A19

W835

RESET

C4039

0.1 F

W837

WR

HA19

HA18

HA17

HA7

HA6

A5

1.6

HA5

HA4

HA3

CE# A2

2.5

HA2

A0 A1

1.6

HA1

B C

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

D E

SD_D15

0

1.2

0

SD_D14

SD_D13

C4040

SD_D12

0.1 F

SD_D11

SD_D10

SD_D9

SD_D8

RAMDQM

RAMCLK

C4041

0.1 F

2

3.3

2.1

R4048

3.3

47K

1.5

NC

0

0

0

0

NC

0

SD_A11

SD_A9

SD_A8

SD_A7

SD_A6

SD_A5

SD_A4

0.2

0.2

1.0

1.0

1.0

0.9

0

0.5

0

1.7

0.8

1.5

2.0

3.3

0.4

64M SDRAM IC

IC4005

M12L64164A-7T

A10/AP

A0

A1

A2

A3

VDD

RAS

CS

BA0

BA1

VSSQ

DQ7

VDD

LDQM

WE

CAS

DQ3

DQ4

VDDQ

DQ5

DQ6

VDD

DQ0

VDDQ

DQ1

DQ2

VSSQ

A8

A7

A6

A5

A4

VSS

CKE

NC

A11

A9

VDDQ

DQ8

VSS

NC

UDQM

CLK

DQ12

DQ11

VSSQ

DQ10

DQ9

VSS

DQ15

VSSQ

DQ14

DQ13

VDDQ

0.8

0.4

0

0.5

3.3

1.5

3.3

C4044

0.1 F

C4050

0.1 F

SD_D0

SD_D1

SD_D2

3.2

3.2

0.2

3.1

0.5

3.1

1.9

0.2

0

0

0.3

3.3

0.9

3.3

1.3

0.8

C4045

0.1 F

0

1.3

3.3

0

C4046

0.1 F

C4047

0.1 F

SD_D3

SD_D4

SD_D5

SD_D6

SD_D7

RAMDQM

RAMWE#

RAMCAS#

RAMRAS#

RAMCS1#

SD_BA0

RAMCS0#

SD_A10

SD_A0

SD_A1

SD_A2

SD_A3

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

F G

G

2

PCB130

VMC298

H

1

G-4

4

3

H

8

7

6

5

8

A B C D E

RF AMP/DSP SCHEMATIC DIAGRAM

(DVD PCB)

F G

7

6

5

FROM/TO LODER

11

12

13

14

15

16

8

9

10

3

4

5

1

2

6

7

17

18

19

20

21

22

23

24

CP2601

09-5000-024-001

T-

T+

F-

F+

MON(DVD)

VOL(DVD)

GND(DVD)

LD(DVD)

LD(CD)

VOL(CD)

GND(CD)

MON(COM)

RF

C

B

A

D

F

E

VCC

Vref

GND(PDIC)

NC

NC

C2634

0.1

F

C2648

0.1

F

P.CON+A5V

OPU_RF

OPU_C

OPU_B

OPU_A

OPU_D

OPU_F

OPU_E

OPU_VREF

TR-

TR+

FO-

FO+

DVDPD

VR_DVD

DVDLD

CDLD

VR_CD

RF_GND

CDPD

4

3

2

FROM/TO LODER

CP2602

00_6232_008_006

1 SLD-

4

5

2

3

6

7

8

SLD+

SP1-

SP1+

LIMIT SW

GND

SP_FG

+5V

FROM LODER

CP2603

A2001WV2-3P

1

2

3

CLOSE

GND(D)

OPEN

MOT_SLED-

MOT_SLED+

MOT_SPDL-

MOT_SPDL+

R2649

HOME

100

NC

W861

P.CON+A5V

R2652

100

R2653

100

TIN_SW

TOUT_SW

P.CON+3.3V

4

MOT_SPDL+

R2625

MOT_SPDLR2626

VR DVD CTL

Q2603

2SK3018

D

S

0

0

G

0.7

R2620

4.7K

VR CD CTL

Q2604

2SK3018

D

S

0

0.5

G

R2647

0

4.7K

VR SEL CTL

Q2605

2SK3018

D

S

0

0

G 0.7

R2623

4.7K

TP8

C2635

OPU_RF

3

0.001 B

TP10

OPU_D

OPU_C

OPU_B

OPU_A

C2603

0.0022 B

C2604

0.0022 B

C2605

TP22

NC

NC

2.5

2.5

0.0022 B

C2606

0.0022 B

C2607

2.5

3.7

33P CH

3.7

TP19

2.7

TP20

2.7

TP21

2.7

2.6

2.7

2.7

2.7

2.6

0

0

0

TP9

TP12 TP11

FNN

FNP

1.5

64

0

63

3.1

62

3.1

61

4.3

60

4.3

59

5.1

58

2.4

57

2.6

56

3.5

55

3.5

54

2.3

53

0

52

0

51

0

50

0

49

0

R2611 4.7K

1.5

DVDRFN

SDATA

R2612 4.7K

A2

1 DVDRFP

48 SDEN

SCLK

3.3

3.3

B2 V33

C2

D2

CP

CN

D

C

B

A

CD_D

CD_C

CD_B

2.6

17

2.6

18

5.1

19

16

5.1

CD_A

20

3.7

21

5.1

22

0.2

23

READ CHANNEL IC

0.2

24

IC2601

ZR36707TQC

33 LINK

LCP

LCN

MNTR

CE

FE

TE

PI

V25

V125

TPH

DFT

25

0 3.3

26 27 28 29 30 31

0 2.7

2.2

2.3

2.9

0.2

32

R2602

R2601

4.7K

1.8M

4.2

C2616

4.1

470P CH

0

R2643

1.8

NC

1K

1.7

R2607

1.8

R2608

1.2K

1.6

1.2K

R2609

1.2K

3.3

1.7

R2605

10K +-1%

0

3.3

C2617

0.1

B

0

R2645

1K

R2613

C2654

R2644

2.2K

560P CH

C2620

0.0056

B

C2621

0.0056

B

C2622

0.0056

B

C2623

0.1

F

R2610

5.1K +-1%

C2618

C2615

0.1

4.7K

0.1

F

0.01 B

C2619

B

R2646

2.2K

C2655

0.01

B

W807

W810

W811

TP15

RFA_SDEN

TP16

RFA_DATA

TP17

RFA_SCLK

TP18

AAF_CE

AAF_FE

AAF_TE

AAF_PI

TP26

VBIASS0

TP38

TP35

TP33

VBIASS1

DEFECT

LINK

RF_GND

D_GND

RF_A5V

W806

W862

4.7K

4.7K

R2627

1.5K

W876

R2310

5.6K

R2312

5.6K

R2631

5.2

5

+IN2

0.7

6

1M

-IN2

7

7.3

OUT2

R2306

5.6K

8

5.2

VCC

FCM2012H-102T04

C2305

220P CH

B2605

B2604

FCM2012H-102T04

B2603

FCM2012H-102T04

C2309

0.001 B

0

36

0 3.3

35 34

2.5 2.5

2.5

2.6

33 32 31 30

5.0

29

0

NC

0

28

38

0

27 26

2.5

25

2.5

2.6

24 23

2.5

22

2.5

3.0

21 20

2.5

19

R2648

13K

GND

0

4

+IN1

5.2

3

-IN1

4.1

2

OUT1

1

4.1

P.CON+5V

C2312

0.001 B

RF_GND

W808

SGND

0

1

0

2

9.1

3

0.2

4

0.2

NC

5 6

4.3

7

4.3

8 9

4.1

NC

4.0

37

10 11 12 13 14 15 16 17 18

5.3 3.1 4.2 4.2

9.1 2.5

0 2.5

2.5

R2328

R2325

4.7K

6.8K

DVDLD

CDLD

TP043 TP39

B2601

FCM2012H-102T04

R2615

DVD LD CTL

Q2601

2SA1036K

D2601

KDS120RTK

4.5

3.9

10

R2616

1K

1.0

C2640

6.3V

100 YK

TP40

B2602

FCM2012H-102T04

C2641

1.0

CD LD CTL

Q2602

2SA1036K

4.5

3.9

6.3V

100

YK

R2617

1K

R2618

10

TP41

TP42

C2302

R2303

C2303

R2304

0.1

B

2.2

0.1 B

2.2

C2307

C2308

0.1 B

0.1 B

D_GND

1

A B C

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

D

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

E F G

G-5

H

8

FROM/TO MPEG/MICON

SPDL_SENS

TOUT_SW

TIN_SW

RFA_SDEN

RFA_DATA

RFA_SCLK

AAF_CE

AAF_FE

AAF_TE

AAF_PI

VR_SEL

FNN

FNP

VBIASS0

VBIASS1

DEFECT

LINK

MIRR

LDON

HOME

GND

D_GND

P.CON+5V

P.CON+A5V

P.CON+3.3V

7

6

SMUTE

TRACK_DAC

FOCUS_DAC

SPINDLE_PWM

SLED_PWM

ADCIN_7

ADCIN_5

ADCIN_6

P.CON+9V

M_GND

5

H

PCB130

VMC298

4

3

2

1

G-6

A B C D

AUDIO/VIDEO SCHEMATIC DIAGRAM

(DVD PCB)

E F G H

8 8

7

FROM/TO MPEG/MICON

P.CON+A5V

DAC_VIDEO_A

DAC_VIDEO_C

DAC_VIDEO_B

DAC_VIDEO_D

P.CON+5V

P.CON+3.3V

6

AT+5V

P.CON+12V

V_SW

RESET

MC

MD

ML

AMCLK

ABCLK

ALRCLK

ASDATA0

SPDIF

GND

5

D_GND

SPDIF

P.CON+A5V

DVD_AUDIO_L

DVD_AUDIO_R

R8134

470

R8135

470

B8102

FCM2012H-102T04

B8101

FCM2012H-102T04

OPTICAL

OS8101

OFTG038101

1 INPUT

2

3

VCC

GND

R8130

2.2K

1.7

1.2

D AUDIO DRIVER

Q8107

KTC3875S_Y_RTK

0

B8103

FCM2012H-102T04

DVD AUDIO OUT

J8101

MSP-213V1-732_PBSN

3

H2

2

H1 H1

5

E

1

E

4

7

DAC_VIDEO_A

DAC_VIDEO_C

DAC_VIDEO_B

DAC_VIDEO_D

C8134

12P CH

L8101

1uH 0305

C8135

12P CH

L8102

1uH 0305

C8136

12P CH

L8103

1uH 0305

C8137

12P CH

L8104

1uH 0305

W819

W820

C8144

6.3V

470 YK

C8146

6.3V

470 YK

C8145

W865 6.3V

470 YK

8

C

Y/C SEPA

J8102

MDC-070V

2

4 3

1

Y

9

6 5

DAC_D_DVD_VIDEO

1

NC NC

2 3 4 5 6 7 8

11 12 13 14 15 16 17 18

NC NC NC

L H

S/CVBS

VIDEO OUT SW

SW8101

COMP

SK42H01G9A

10 11

12

H1

5

4

E

H2

3 2

H1

1

E

YUV OUT

J8103

MSP-213V1-652_PBSN

7

6

5

AT+5V

P.CON+12V

4

TO MEMORY

RESET

3

2

1

G-7

B7301

FCM2012H-102T04

B7302

FCM2012H-102T04 R7307

10K

C7310

50V 2.2

YK

R7306

10K

2.6

8

2.6

7

5.2

6

3.2

5

0

4

3.1

3

3.1

2

3.1

1

C7308

50V 2.2

YK

0

9

2.6

10

2.9

11

3.0

12

NC

3.0

13

3.0

14

2.9

15

3.1

16

AUDIO SIGNAL(PB)

PLAYBACK LUMINANCE SIGNAL

PLAYBACK COLOR SIGNAL

PLAYBACK VIDEO SIGNAL

DIGITAL AUDIO SIGNAL(PB)

A B

R.SIGNAL

+ COMPONENT SIGNAL(U)

B.SIGNAL

+ COMPONENT SIGNAL(V)

C

4

R8102

100K

R8101

10K

C8106

0.0015 B

R8104

10K

R8108

10K

0

4

5.8

3

5.8

2

5.8

1

-

+

-

+

R8106

5.8

5

5.8

6

5.8

7

11.6

8

47K

C8112

50V 22 YK

R8112

470

C8113

R8113

50V 22 YK

56

R8115

6

470

C8105

0.0015 B

R8111 R8114

10K 1K

5

R8123

4.7K

3.2

0

MUTE SW

Q8106

KRC104SRTK

2.6

ZERO

SYS_MUTE

DVD_AUDIO_R

5.0

5.0

-0.2

MUTE SW.

Q8103

KRA101SRTK

MUTE SW

Q8105

KTC3875S_Y_RTK

0

R8124

-0.3

1K

0

0.6

0.3

0

D8101

0

5.0

MCL4148

MUTE SW.

Q8102

0

KRC103SRTK

MUTE DET

Q8101

KTC3875S_Y_RTK

0

R8122

1K

-0.3

0

MUTE SW

Q8104

KTC3875S_Y_RTK

DVD_AUDIO_R

DVD_AUDIO_L

DVD_AUDIO_L

DAC_D_DVD_VIDEO

SYS_MUTE

RESET

CAUTION: DIGITAL TRANSISTOR

FRON/TO TUNER/JACK

NC

CP8102 (CP8002)

IMSA-9604S-08C

DVD_AUDIO_R

GND

8

7

DVD_AUDIO_L

GND

DAC_D_DVD_VIDEO 4

SYS_MUTE

DVD_RESET

3

2

1

6

5

1.25m FFC

CD8002

2F080601

PCB130

VMC298

CAUTION: DIGITAL TRANSISTOR

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

D E F G H

3

2

1

G-8

8

A B C D E

Y/C/AUDIO/CCD/HEAD AMP SCHEMATIC DIAGRAM

(VCR PCB)

F G

BUFFER

Q109

KTC3875S_Y_RTK

R129

1.8K

4.9

3.9

3.3

FSC

7

6

5

4

3

2

1

FROM POWER

P.CON+5V

GND

C142_1

FROM/TO HI-FI/DEMODULATOR

17

16V 47 KA

C143

1 F

R127

680K

C141

0.01 B

4

3

6

5

2

1

FSC

TO_NORMAL_A

FROM_NORMAL_A

HF1

HF_COM

HF2

A.VCC

FROM/TO CYL

CP101

TOC-C09X-A1

9 HF1 (R)

8

7

HF_COM

HF2 (L)

SP-CH1 (R)

SP_COM

SP-CH2 (L)

EP/LP-CH1 (R)

EP/LP COM

EP/LP-CH2 (L)

P.CON+5V

L107

22uH 0305

C103_1

6.3V

22 KA

A.VCC

TO_NORMAL_A

R105

1K

C129

1 B

6.3V

C174

47 KA

P.CON+5V

FROM/TO HEAD AUDIO CONTROL

4

3

2

1

CP102

IMSA-9604S-06C

6 AUDIO REC

5 AUDIO PB

FFC

CTL+

CTL-

AE HEAD(+)

AE HEAD(-)

CD102

2H061504

CTL+

CTL-

V.REC_ST-H

2.2K

AUDIO PB SW

Q101

KTC3875S_Y_RTK

0

0.7

R140

R101

560

1/4W

R102

10K

0

5.2

5.3

2

1

TO FULL ERASE HEAD

CP103

B2013H02-2P

FE HEAD(GND)

FE HEAD(HOT)

GND

HOT

AUDIO PB SW

Q102

KTC3875S_Y_RTK

0

0

0.7

0

R103

10K

SW

Q103

KRA103SRTK

20

6

5

4

6.3V

C105_1

22 KA

1

2

3

COIL,BIAS OSC

L101

1626009

L102

100uH 0305

0

5.2

0

BIAS CTL

Q105

KTA1266

BIAS OSC

0

Q104

KTC3203_Y

5.2

R108

22K

C110_1

16V 47 YK

C112

6.3V

220 KA

R109

1K

1/4W

R112

330K

C118

0.01 B

R114

20K

C122

0.0012

B

L103

5.6uH

C166

0.068 B

C165

0.047 F

C169

0.047 F

2.1

2.9

1.6

1.8

1.9

1.8

5.0

1.8

1.6

1.8

1.8

1.8

2.3

4.9

2.3

0

0

0

C109

2.3

0.1

B

Y/C/AUDIO/CCD/HEAD AMP IC

IC101

LA71206M-MPB

0

4.8

4.8

60 59

KILL

DET

HA

GND

CHROMA

DET

ACC

DET

P

P

ENV

DET

R

0 5.2

58 57

0

56

AUDIO

MUTE

HA SW

C-ROT C-GND

RF-SW

IN

5.2

55

5.2

54

5.2

SERAIL

DECODER

53

4.9

52

C-VCC

2.1

51

4.8

50

4.1

49

VX01

3.2

48

320FH

VCO

3.3

47

3.2

46

NC

4.9

4.9

1.2

2.2

0.8

45 44 43 42 41

SLD

B

ALWAYS

5V

VDD 4Fsc

PLL

CLOCK

VSS

P

R

TIMMING OUT

OUT

REC

APC

PB

APC

REC

AFC

DRIVER

R P

BEFORE

BGA

BGA

CCD

AUTO-BIAS

VSS

CLAMP

IN

AFTER

CNC

BGA

R P VCA

P R

PB

AMP

VCA

H

L

3.58M

BPF2

CLAMP

C-LPF

Main

CONV

B-UP

AMP

B.D

P

VCP HA VCC

+

ACC

AMP

R

3.58M

BPF1

1

2

3

HA

PRE GND

P

H

L

4.21M

BPF

Sub

CONV

DETAIL

ENH

ACC

DET

R

P

CLAMP

P R

PB-C

P

YNR/COMB

R

N.L.

DEEM

PB-C

VIDEO

AGC

1/2

FBC

REG

4V

BAL

TC1

R

NL

EMPHA

NL

EMPHA

Y-LPF

R

NC1

Y/C

MIX

R

P

R

P

P

FM

MOD

AGC

TC2

A-GND

R-EQ

TEST

NORMAL

QV/QH

6DB

DOUBBLE

LIM

FM

DEM

SUB

LPF

1

2

3

ALC R

P

LINE

AMP

REC

FM-EQ

SYNC

SEP

A-VCC

LPF

MAIN

DE-EM V.SYNC

SEP

ALC

DET VREF

P R

FM

AGC

PB

FM EQ

VHS

S-EQ

SOPB

P

PB,EE

2.3

Vref

2.3V

1

2.3

2

2.3

3

2.3

EQ

AMP

SP,LP

4

2.3

5

2.3

6

PB,EE

REC:LP<EP

PB:EP

0

7

2.3

8

2.3

REC

AMP

9

MUTE

10

0.8

4.8

AUTO

BIAS

PHASE

EQ fo-ADJ

PHASE

EQ

Q-ADJ

11 12 13

1.1

1.1

1.4

14

2.0

FM

AGC

FIL

15

R

Y-GND

16

0 2.6

P R Y-VCC

17

NC

MAIN

EMPHA

FIL

18

2.6

S

DET

0.2

19

B

2.8

20

0

1.6

0

3.2

2.5

3.2

3.3

2.6

2.6

4.1

2.3

2.3

2.1

1.6

3.6

4.1

5.0

4.4

3.2

2.1

C133

1 F

Q107

KTA1504S_Y_RTK

C134

0

50V 1 KA

50V

35V

C135

0.22

C136

22

BUFFER

50V

50V

YK

C132

1

1.6

2.2

C137_1

YK

KA

1 KA

C139

0.1

50V

F

C140

4.7

KANP

R124

82K

50V

R122

100K

C138

1

W809

YK

R120 3.6

220

0

4.2

R121

1K

BUFFER

Q106

KTA1504S_Y_RTK

0

19

18

V.ENV

TP101

NC

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

CAUTION: DIGITAL TRANSISTOR

AUDIO SIGNAL(PB)

AUDIO SIGNAL(REC)

PLAYBACK VIDEO SIGNAL

TUNER VIDEO SIGNAL

4FSC

TU/REAR_V_IN

FRONT_V_IN

R143

1K

R141

DVD_V_OUT[DAC_D]

1K

16

Y/C_VIDEO_OUT

C.SYNC

DUMMY_V.SYNC

P.CON+5V

PLAYBACK COLOR SIGNAL

PLAYBACK LUMINANCE SIGNAL

RECORD COLOR SIGNAL

RECORD LUMINANCE SIGNAL

A B C D E F G

G-9

H

7

FROM/TO TUNER/JACK

FRONT_V_IN

DVD_V_OUT[DAC_D]

TU/REAR_V_IN

Y/C_VIDEO_OUT

FSC

FROM OPERATION/DISPLAY

FRONT_V_IN

FROM/TO SYSCON

4FSC

Y/C_CLK

Y/C_DATA

Y/C_CS

DUMMY_V.SYNC

V.REC_ST-H

C.ROTARY

AUDIO_MUTE-H

CTL-

CTL+

H.AMP_SW

COMP

ENV.DET

H.SW

C.SYNC

6

5

4

8

3

2

PCB010

VMC300

H

1

G-10

A B C D E

SYSCON SCHEMATIC DIAGRAM

(VCR PCB)

F G H

TP3002 H.SW

NC

8

7

FROM/TO POWER

TX

RX

DVD_POWER_CTL

AT+12.6_V

P.CON+5V

AT+5V[M-CON]

VCR_POWER_ON-L

POWER_FAIL

AT+5.2V

GND

MOTOR_GND

6

5

FROM/TO DECK

CP3001

TMC-J12P-B2

7

8

9

5

6

10

11

12

1

2

3

4

CAP FG

CAP VCO

VCC

CAP.M/F/R

I LIMIT

MOTOR GND

GND

LD/CY VCO

CAP CTL

LDM CTL

CYL FG/PG

CYL CTL

4

BOT SENSOR

Q3008

ST-304L

0

5.0

3

2

1

C3033_1

35V 330

0

YK

L3002

22uH

R3003

3.3K

CAP_FG

W818

AT+12.6_V

P.CON+5V

CAP_F/R

CAP_LIMIT

C3040

1 F

AT+12.6_V

CONTROL_IN

LDM_CTL

CYL_FG/PG

CYL_DRIVE

5.0

EOT SENSOR

Q3006

ST-304L

R3011

47K 1/4W

AT+5.2V

(LED_GND)

AT+5.2V

TAB_SW

EOT

BOT

23

C3025

12P CH

X3001

100BT01004

10MHz

R3034

1M

C3047

15P CH

CAP_LIMIT

LDM_CTL

CAP_F/R

C3008

0.0047 B

24

CONTROL_IN

CYL_DRIVE

CYL_FG/PG

R3008

1K

C3007

0.1

B

AT+5V[M-CON]

TV/VCR

POWER_MUTE-L

SYS_MUTE

AV_SW1

Y/C_CS

RF_CH_SW

AUDIO_MUTE-H

V.REC_ST-H

C.ROTARY

H.AMP_SW

COMP

R3031

H.SW

HIFI_H.SW

C3004

1M

C.SYNC

R3057

22K

R3032

10K

21

0.022

DUMMY_V.SYNC

W835

B

NC

NC

5.0

NC

5.0

0.1

5.0

NC

0

3.3

84

5.0

NC

0

83

5.1 3.4 2.5

82 81 80

0

79

5.1

SYS MUTE

FL CLK/VSC CLK

FL DATA/VSC DATA

AV SW2

AV SW1

Y/C CS

85

86

87

78 77 76

VCR_H

POWER MUTE-L

75

5.1

0

RF CH SW

0

2.4

AUDIO MUTE-H

V.REC ST-H

0

LDM_CTL

CAP FWD-L

2.5

0

0

C.ROTARY

H.AMP SW

2.7

0

COMP

CAP FULL

3.0

2.5

CYL SPEED UP

D FG/PG

2.5

VIDEO H.SW

HIFI H.SW

R3014 56K 2.7

R3012

56K

2.7

0

DRUM PWM

CAP PWM

111

112

C SYNC

VCC (BACK UP)

0

DUMMY_V.SYNC

VSS (GND)

0.4

5.1

74

0

73

NC

72

0

71

NC

70

NC

69

0

68

4.8

67

4.8

66

0

65

4.9 5.0

64 63

4.8 4.8

62 61

0 4.8

4.8

60 59 58

0

57

C3061

0.1 F

5.1

SYSCON/TIMER/SERVO IC

IC3001

OEC0138B

56

55

54

31

30

29

VCC (BACK UP)

SEG1

Y/C DATA

ST SELECT

KEY-A

KEY-B

0

4.8

5.0

Y/C CLK

5G/CS/BS LED

5.0

5.0

4G/TIME SHIFT LED

3G/TV/VCR LED

2G/DUB/REC LED

5.0

5.0

1G/VCR/T-REC_LED

ZERO

5.0

VCR LED

DVD RESET

0.3

DVD LED

DVD_POWER_CTL

5.1

0

3.3

REM IN

4.7

5.0

NC

POWER ON-L

0

VIDEO_MUTE-H

REC_L/ REEL T

0

0.1

VSC_L/ REEL S

POWER FAIL

5.0

5.1

AVCC (BACK UP)

TAB SW

0

0

SERVICE

AFT S.CURVE

2.5

3.7

HiFi ENV

0

5.2

5.2

CTL+

CTL-

R3017

560

R3020

560

0

C3013

1

6.3V

22 KA

0

2

2.5

3 4

0 2.5

5

0.1

6

2.6

7

2.5

8

2.3

9

5.1

10 11 12 13 14 15 16 17 18 19

2.0

2.0

1.5

0.4

0 3.1

2.6

5.1

2.6

0

20 21 22 23 24 25 26 27 28

0

NC

2.5

0 2.6

0 0 1.3

1.3

25

C3016

22

R3025

470 C3038

L3003 1 F

6.3V

47 KA

12uH

C3044

D3007

1SS133

R3010

10K

12P CH

RX DRIVE

Q3003

KRA103SRTK

5.2

5.3

W838

0

0

0

3.4

RX DRIVE

Q3007

KRC103SRTK

RX

W837

SEG_1

Y/C_DATA

Y/C_CLK

5G/CS/BS_LED

4G/VSC_LED

3G/TV/VCR_LED

2G/DUB/REC_LED

1G/VCR/T-REC_LED

VCR_LED

DVD_LED

DVD_POWER_CTL

R3055

R3038

C3036

REM_IN

22K

VCR_POWER_ON-L

4.7K

1/4W

VIDEO_MUTE-H

AT+5.2V

REC_L/REEL-T

0.1

F

VSC_L/REEL-S

POWER_FAIL

AT+5V[M-CON]

TAB_SW

SERVICE

NC

TP3001

AFT-S.CURVE

HIFI_ENV.DET

ST_SELECT

KEY-A

KEY-B

AT+5.2V

C3015

820P CH

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

A B

P.CON+5V

AT+5.2V

MS_SEN B

Q3004

RPI-352C40N

5.1

2

1

0.9

3

5.1

MS_SEN A

Q3005

RPI-352C40N

0.9

2 3

5.1

4

1.3

0.4

1 4

1.3

2

3

1.2

5.2

1

4

2.4

0

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

C

27

0

2

5.2

3

1

1.2

REEL SENS

Q3001

RPI-303

4

0

D

NC

0

5

NC

NC

0

4

NC

R3049

47K

OUT

5.0

1

IN

5.0

2

GND

0

3

D3009

1SS133

RECORD LUMINANCE SIGNAL

RECORD COLOR SIGNAL

PLAYBACK LUMINANCE SIGNAL

PLAYBACK COLOR SIGNAL

E

8

5.2

7

0

6

5.0

5

4.9

1

0

2

0

3

0

4

0

CAUTION: DIGITAL TRANSISTOR

F

C3030

1 F

TX

MD0

RESET

FWE

AT+5V[M-CON]

FROM/TO HI-FI/DEMODULATOR

V.REC_ST-H

HIFI_ENV.DET

HIFI_H.SW

AUDIO_MUTE-H

SCL

SDA

ST_SELECT

FROM/TO OPERATION1/DISPLAY

DVD_LED

VCR_LED

KEY-A

KEY-B

REM_IN

1G/VCR/T-REC_LED

2G/DUB/REC_LED

3G/TV/VCR_LED

4G/VSC_LED

5G/CS/BS_LED

SEG_1

SEG_2

SEG_3

SEG_4

SEG_5

SEG_6

SEG_7

SEG_8

SEG_9

SEG_10

JG3002 JG3003 JG3004 JG3005 JG3006 JG3007 JG3008

CAUTION: DIGITAL TRANSISTOR

G

FROM/TO Y/C/AUDIO/CCD/HEAD AMP

DUMMY_V.SYNC

C.SYNC

V.REC_ST-H

C.ROTARY

AUDIO_MUTE-H

CTL-

CTL+

H.AMP_SW

COMP

ENV.DET

H.SW

Y/C_CS

Y/C_DATA

Y/C_CLK

4FSC

FROM/TO TUNER/JACK

RF_CH_SW

SW_V_OUT

AV_SW1

SCL

SDA

AFT-S.CURVE

TV/VCR

VIDEO_OUT

POWER_MUTE-L

VIDEO_MUTE-H

DVD_RESET

SYS_MUTE

H

PCB010

VMC300

G-11

8

7

6

5

4

3

2

1

G-12

1

2

3

A B C D E

TUNER/JACK SCHEMATIC DIAGRAM

(VCR PCB)

8

7

6

5

4

TU301

115-V-H015ARE

A.IN

V.IN

1

CH 2

+B 3

CONTROL 4

5

RF MUTE SW

Q301

KTC3875S_Y_RTK

0

0 0

16V

C315

10 KA

R304 C318

RF_CONV_A_OUT

10K

16V 10 KA

RF_CH_SW

L301

P.CON+5V

22uH 0305

TV/VCR

R302

1K

L

3

E

H2

2

R

1

H1

E

H1

V

4

5

REAR OUT JACK

J8001

MSP-213V1-432_PBSN

VIDEO OUT

TP8001

NC

NC

7

FSC 8

NC 9

CLOCK

10

DATA 11

AFT

12

NC 13

SIF OUT

14

TU 32V

15

NC

16

V.OUT

17

NC

NC

NC

NC

C307

100P CH

C308

0.01 B

W821

C303

0.1 F

W879

R306

120

FSC

D8003

MTZJ6.8B

SCL

SDA

AFT-S.CURVE

+32V

C313

16V 10 KA

TU_V_OUT

C8014

0.1

F

C8013

50V 10 YK

P.CON+12V

R8009

470 1/2W

VIDEO MUTE SW

Q8003

KRC103SRTK

3.3

VIDEO_MUTE-H

0

0

0

3.3

2.6

BUFFER

Q8004

KTA1266

R8011

100

R8014

390

R8015

390

MUTE SW

Q8005

KTC3875S_Y_RTK

0

MUTE SW

Q8006

KTC3875S_Y_RTK

0

0

0

0

R8016

2.2K

0

R8017

2.2K

R8032

470 R8056

470

0

MUTE SW

Q8007

KRA103SRTK

5.0

5.2

SIF_OUT

TU/REAR_V_IN

E

1

H

2

C8099

470P CH

C8004

470P CH

E

1

H

2

E

1

3

NC

2

H

C8019

16V 10 KA

R8059

4.7K

1/4W

D8008

1SS133

TU_V_OUT

C8031

50V 4.7

KA

C8032

16V 4.7

KANP

7.8

8.4

0

AV SW IC

IC8005

MM1501XNRE

0

Vin1 SW1

7.0

GND V OUT

11.7

Vin2 Vcc

32

F

L8004

47uH

AUDIO_OUT_R

AUDIO_OUT_L

AT+5.2V

POWER_MUTE-L

P.CON+5V

VIDEO_OUT

DVD_RESET

SYS_MUTE

DVD_V_OUT[DAC_D]

DVD_A_OUT_L

DVD_A_OUT_R

AV_SW1

SW_V_OUT

P.CON+12V

AUDIO_OUT_L

AUDIO_OUT_R

RF_CONV_A_OUT

G

FROM/TO AUDIO/VIDEO

NC

CP8002

(CP8102)

IMSA-9604S-08C

DVD_RESET

SYS_MUTE 6

DAC_D_DVD_VIDEO 5

8

7

GND

DVD_AUDIO_L

GND

DVD_AUDIO_R

4

3

2

1

FFC

CD8002

2F080601

FROM/TO Y/C/AUDIO/CCD/HEAD AMP

DVD_V_OUT[DAC_D]

FSC

TU/REAR_V_IN

FRONT_V_IN

Y/C_VIDEO_OUT

FROM/TO SYSCON

DVD_RESET

SYS_MUTE

SCL

SDA

AV_SW1

TV/VCR

RF_CH_SW

AFT-S.CURVE

POWER_MUTE-L

VIDEO_MUTE-H

VIDEO_OUT

SW_V_OUT

FROM/TO HI-FI/DEMODULATOR

DVD_A_OUT_R

DVD_A_OUT_L

SIF_OUT

FRONT_A_IN_L

FRONT_A_IN_R

AUDIO_OUT

HIFI_A_OUT_R

HIFI_A_OUT_L

H

FROM POWER

GND

+32V

AT+5.2V

P.CON+5V

P.CON+12V

G-13

CAUTION: DIGITAL TRANSISTOR

A

CAUTION: DIGITAL TRANSISTOR

B

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

C D

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES

DESCRIBED IN PARTS LIST ONLY

ARE

E

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE

N’UTILISER QUE CELLS DECRITES

DANS LA NOMENCLATURE DES PIECES

F

8

7

6

5

4

3

2

G

PLAYBACK VIDEO SIGNAL

TUNER VIDEO SIGNAL

AUDIO SIGNAL(PB)

AUDIO SIGNAL(REC)

PLAYBACK COLOR SIGNAL

PLAYBACK LUMINANCE SIGNAL

RECORD COLOR SIGNAL

RECORD LUMINANCE SIGNAL

H

PCB010

VMC300

1

G-14

8

A B C D E

OPERATION/DISPLAY SCHEMATIC DIAGRAM

(VCR PCB)

V651 CO2D0M3-A

F G H

8

7

6

5

15 14 13 12 11 10 9

SEG1 SW

Q664

KRC103SRTK

0 1.9

2.0

R674

5.2

1G SW

Q665

KTA1504S_Y_RTK

1.7

4.9

180

SEG2 SW

Q663

KRC103SRTK

0 0.4

4.0

SEG3 SW

Q662

KRC103SRTK

0

4.0

R673

180

0.4

2G SW

Q661

KTA1504S_Y_RTK

5.2

1.7

R672

180

4.9

SEG4 SW

Q660

KRC103SRTK

0 1.1

4.0

SEG5 SW

Q658

KRC103SRTK

R670

180

0

3.0

1.0

3G SW

Q659

KTA1504S_Y_RTK

5.2

1.7

R668

180

4.9

SEG6 SW

Q657

KRC103SRTK

0 0.4

8

R667

7

180

4.0

6 5 4 3 2 1

4.9

SEG10 SW

Q652

KRC103SRTK

R662

180

SEG9 SW

Q653

KRC103SRTK

0.9

4.0

R663

180

0.4

5G SW

Q651

KTA1504S_Y_RTK

4.0

5.2

SEG8 SW

Q655

KRC103SRTK

1.3

4.9

R665

180

R666

3.1

180

4G SW

Q654

KTA1504S_Y_RTK

3.5

SEG7 SW

Q656

KRC103SRTK

0

0

0

0

0

0

1.7

5.2

OS651

PIC-37043LO-H

Vout

GND

B+

1

2

3

4.9

0

5.1

R651

100 1/4W

REM_IN

AT+5.2V

4

GND

D656

1N4005-EIC

3

R683

560

5.2

0

5.2

DVD LED SW

Q666

KRA103SRTK

W802

AT+5.2V

KEY-A

2

1

G-15

A

CAUTION: DIGITAL TRANSISTOR

B

CAUTION: DIGITAL TRANSISTOR

C

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

D

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

E

R657

2.7K

R658

1.8K

F

R659

1.5K

KEY-B

AUDIO SIGNAL(REC)

RECORD COLOR SIGNAL

RECORD LUMINANCE SIGNAL

G

FROM POWER

LEM_VCC

AT+5.2V

GND

FROM/TO SYSCON

DVD_LED

VCR_LED

1G/VCR/T-REC_LED

2G/DUB/REC_LED

3G/TV/VCR_LED

4G/VSC_LED

5G/CS/BS_LED

SEG_1

SEG_2

SEG_3

SEG_4

SEG_5

SEG_6

SEG_7

SEG_8

SEG_9

SEG_10

REM_IN

KEY-B

KEY-A

7

6

5

4

3

2

PCB010

VMC300

H

1

G-16

4

3

2

1

G-17

A

6

5

8

7

A B C

C743_1

50V 0.22

C744

0.1

F

KA

R716

3.3K

D E

HI-FI/DEMODULATOR SCHEMATIC DIAGRAM

(VCR PCB)

F G

P.CON+5V

HIFI_A_OUT_R

16V

C752_1

22 KA

A.VCC

L702_1

22uH 0305

ST_SELECT

HIFI_A_OUT_L

P.CON+12V

AUDIO_OUT

TO_NORMAL_A

FROM_NORMAL_A

C758_1

L703

100uH 0305

16V 22 KA

C754

16V 47 KA

W803

R718

1K

R719

330

C755

0.022 B

C747

50V 10 YK

C748

0.1 F

C750_1

50V 2.2

KA

R717

2.2M

C746

0.1

F

C749

0.1

F

C756_1

16V 10

W880

C757

1 F

KA

HI-FI/AUDIO/HEAD AMP/DEM IC

IC701

AN3663FBP

2.2

48

3.4

0

47

DEM_BLK

3.5

46

2.1

45

2.3

44

4.7

43

4.7

42

C751

0.1

F

2.7

4.9

2.5

MAIN

DEEN

4.5M

TRAP

SUB

BPF

CUE

BPF

SUB

DET

FM

DEMOD

0

41

4.9

40

0

NC

39

0

38

1.6

37

LOGIC

AM

DEMOD

95HMz

BPF

MUTE VCO-F0

CTL ADJ

LOGIC

3.5M

VCO

COMP

LOGIC

SW21

PNR RCH

ZZ-PROM

S/N

SW NOISE

4.2

SW9

AUDIO

LIMIT

2.3

1.2

4.3

11.0

0

LOG

AMP

AMP

USA

AN3663FBP

AMP

SUB DEEN

OUTPUT SW

R L

AMP

MATRIX

MUTE

R

FROM 1PIN

SW18

BS

SW19

R

L

HIFI

MIX

MUTE

L

SW17

R

L

SW16

MIX

HIFI

BS

FROM 3PIN

RFC

PC PB LPF

RCH BPF

FM UM

SW10

LCH BPF

PC PB LPF

0

36

2.4

35

0.7

34

2.4

33

SW12

PB REC

RCH

VCO

REC LPF

HPF

NOISE

DET

LINER

SW

HOLD

TIMING

C759

35V 22 KA

C760

1 F

4.3

1.0

2.4

2.3

2.2

DET

SW22 L

MIX

R

SW2

PNR LCH

L

INPUT_SW(L)

R

INPUT_SW(R)

AUDIO

LIMIT

SW4

SW NOISE

MIX

S/N

REC LPF

LCH VCO

SW14

DET

AGC

CURR

-

-

+

SW15

H

SW11

L

0.6

2.3

1

0

2

2.3

3

VREF1

0

4 5 6

2.2

2.4

2.1

7

0.5

8 9

0

NC

10

0

11 12

0 2.0

2.2

13 14

0

NC

15

0 2.4

16

2.4

2.1

C730

C731

0.015

B

50V 0.22

KA

1.8

1.8

D701

1SS133

1.8

C732 0.01 F

2.5

C729 0.01 B

0

C722

0.1 B

4.9

0.6

C723

0.01

F

0

6.3V

C761

47 KA

0.7

C724

0.01 F

0

0

C725 0.1 B

2.4

C726 0.015

B

HIFI ENV.

TP701

NC

V.REC_ST-H

HIFI_ENV.DET

28

L704

HIFI_H.SW

10uH

P.CON+5V

2.4

C727_1 16V 10 KA

0.7

C728 50V 10 KA

FROM OPERATION/DISPLAY

FRONT_A_IN_L

FRONT_A_IN_R

FROM/TO TUNER/JACK

SIF_OUT

DVD_A_OUT_L

DVD_A_OUT_R

AUDIO_OUT

HIFI_A_OUT_R

HIFI_A_OUT_L

FROM/TO Y/C/AUDIO/CCD/HEAD AMP

HF2

HF1

HF_COM

FSC

FROM_NORMAL_A

TO_NORMAL_A

A.VCC

FROM POWER

P.CON+5V

P.CON+12V

GND

FROM/TO SYSCON

V.REC_ST-H

HIFI_ENV.DET

HIFI_H.SW

AUDIO_MUTE-H

SCL

SDA

ST_SELECT

B

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

C

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

D E F

AUDIO SIGNAL(REC)

AUDIO SIGNAL(PB)

G

2

PCB010

VMC300

H

1

G-18

4

3

H

8

7

6

5

8

A B C D E

POWER SCHEMATIC DIAGRAM

(VCR PCB)

W870

F G H

8

TO Y/C/AUDIO/CCD/HEAD AMP

P.CON+5V

GND

W806

AT+12.6_V

7

6

D506

1N4005-EIC

D503

1N4005-EIC

L502

W5T_20*10*10A

AC120V_60HZ

CD501

09419910

WHITE

BLACK

WHITE

S502

S501

BLACK

2.5A 125V

F501

51MS025L

2.5A 125V

FH501

EYF-52BCY

FH502

EYF-52BCY

3

1

4

2

COIL,LINE FILTER

L501

0R4A223F20

D502

1N4005-EIC

D505

1N4005-EIC

5

4

3

2

1

G-19

R508

100 1/4W

D504

1SS133

R537

220

R538

220

2.5A 125V

CAUTION

:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE FUSE 2.5A 125V(F501).

ATTENTION

:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE

N’UTILISER QUE DES FUSIBLE DE MEME TYPE 2.5A 125V(F501).

A

D

S

G

0.5

0.1

SWITCHING

Q501

STP5NC50FP

38

39

B

R504

560 1/2W

C509

0.018

M

0.5

PROTECT CONTROL

Q502

KTC3203_Y

0.3

HS501

763WSA0017

0

D531

MTZJ9.1B

C516

250V 0.0047

KX

16.0

8

T501

81260074

0

0

7

6

139.3

4

NC

0

3

142.0

2

PHOTO COUPLER

IC503

PS2561L1-1-V(W)

12.5

0.3

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES

DESCRIBED IN PARTS LIST ONLY

ARE

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE

N’UTILISER QUE CELLS DECRITES

DANS LA NOMENCLATURE DES PIECES

C

5.1

4.1

10

0

11

12.9

12

0

13

0

14

16.6

15

96

R519

1K

D

D507

RGP15J

C531

500V 560P B

W849

W831

B502

W5RH3.5X5X1.0

3.7

3.3V OUT

Q511

KTA1241_Y

3.4

3.2

L505

22uH 0305

9V REG. IC

IC502 KIA78R09API

IN

11.6

1

OUT

9.0

2

GND

0

3

SW

5.0

4

P.CON+12V SW

Q510

KTC3203_Y

12.4

12.2

12.8

P.CON+12V

19.1

P.ON SW

Q509

KRC103SRTK

0

0

W816

VCR_POWER_ON-L

MOTOR_GND

R509

100

P.CON5V SW

Q505

KTC3209_Y

R513

5.9

390 1/2W

5.2

5.1

DVD_POWER_CTL

P.CON+9V

FROM/TO SYSCON

TX

RX

AT+5.2V

DVD_POWER_CTL

VCR_POWER_ON-L

POWER_FAIL

AT+5V[M-CON]

AT+12.6_V

P.CON+5V

GND

MOTOR_GND

TO TUNER/JACK

+32V

AT+5.2V

P.CON+5V

P.CON+12V

GND

D536

1SS133

D537

1SS133

3.1

1.8

3.9

1.8

1.0

3.3V CTL

Q507

KTC3875S_Y_RTK

1.0

3.3V CTL

Q508

KTC3875S_Y_RTK

D522

10ELS6N

R545_1

15 1/4W

D511

21DQ04N

D512

21DQ04N

D518

1SS133

R517

820 1/2W

VOLTAGE CTL IC

IC501 KIA431

C524

0.022 B

L506_1

22uH

TSL0808

C507

2.2

F

C541

2.2

F

4.1

OUT

3

GND

0

2

IN

2.5

1

4.1

0

0

PROTECT

Q530

KTC3875S_Y_RTK

0

PROTECT

Q531

2SA1037AK

13.2

3.3

R536

560

P.CON+5V_DH

P.CON+3.3V

TO OPERATION/DISPLAY

LEM_VCC

AT+5.2V

GND

GND

LEM_VCC

AT+5.2V

P.CON+5V

5.2

5.2

5.8

P.CON+5V SW

Q503

KTC3209_Y

R514

220 1/2W

TO HI-FI/DEMODULATOR

P.CON+5V

P.CON+12V

GND

M-CON +5V SW

Q504

KTA1271_Y

5.2

5.1

4.4

C534

1 F

GND

AT+5V[M-CON]

R544

22K 1/4W

0.1

5.1

0

M-CON POWER SW

Q506

KRC103SRTK

0

D526

MTZJ3.3B

0.7

0

0 0

POWER FAIL SW

Q513

2SC2412K

5.3

POWER FAIL SW

Q514

2SC2412K

+32V

TX

RX

P.CON+3.3V

W867

GND

AT+5.2V

POWER_FAIL

P.CON+5V_DH

P.CON+9V

P.CON+12V

AT+5.2V

NC

FROM/TO MPEG/MICON

CP501

TX

RX

(CP4002)

CH2C0302

P.CON+3.3V

P.CON+3.3V

GND

GND

P.CON+5V

P.CON+9V A

P.CON+9V A

P.CON+12V

AT+5V

7

8

9

5

6

10

11

12

1

2

3

4

PCB010

VMC300

CAUTION: DIGITAL TRANSISTOR

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

E F G H

7

6

5

4

3

2

1

G-20

4

3

2

1

G-21

A

6

5

8

7

A B

B

C D E

OPERATION/LED SCHEMATIC DIAGRAM

(OPERATION PCB)

F

R685

13K 1/4W

R686

6.8K 1/4W

R687

3.9K 1/4W

R688

2.7K 1/4W

R689

3.3K

1/4W

R690

22K 1/4W

DVD LED

D685

LTL-1CHEE-002A FROM/TO OPERATION/DISPLAY

NC

CP681 (CP651)

IMSA-9604S-05Z13

DVD LED

GND

5

4

3

KEY-A

KEY-B

2

1

CD681

2H051202

PCB270

VEBA07

C

NOTE:THE DC VOLTAGE EACH PART WAS

MEASURED WITH THE DIGITAL TESTER

DURING PLAYBACK.

D

NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

E F

G

G

2

H

1

G-22

4

3

H

8

7

6

5

8

A B C D E

INTERCONNECTION DIAGRAM

OPERATION PCB

PCB270

VEBA07

F

FULL ERASE HEAD ASS’Y

G

7

HALL

SENSOR

MAIN

COIL

ROTOR

MAGNET

MR

FG SENSOR

6

5

4

3

DVD

DRIVE

DM-2

OPTICAL PICK-UP

SPINDLE MOTOR

SLED,LOADING MOTOR

FG SENSER

GND(PDIC)

Vref

VCC

E

F

D

A

B

C

RF

MON(COM)

GND(CD)

VOL(CD)

LD(CD)

LD(DVD)

GND(DVD)

VOL(DVD)

MON(DVD)

F+

F-

T+

T-

SLD-

SLD+

SP1-

SP1+

LIMIT SW

GND

+5V

CLOSE

GND(D)

OPEN

7

6

5

9

8

2

1

4

3

20

19

18

17

16

24

23

22

21

15

14

13

12

11

10

4

5

6

7

8

1

2

3

FFC

5

6

3

4

7

8

1

2

20

19

18

17

16

15

24

23

22

21

14

13

12

11

10

9

8

4

3

2

1

7

6

5

CP2601

GND(PDIC)

Vref

VCC

E

F

D

A

B

C

RF

MON(COM)

GND(CD)

VOL(CD)

LD(CD)

LD(DVD)

GND(DVD)

VOL(DVD)

MON(DVD)

F+

F-

T+

T-

7

6

5

9

8

2

1

4

3

20

19

18

17

16

24

23

22

21

15

14

13

12

11

10

4

5

6

7

8

CP2602

1

2

3

SLD-

SLD+

SP1-

SP1+

LIMIT SW

GND

+5V

CP2603

1

2

3

CLOSE

GND(D)

OPEN

OPTICAL

OS8101

1

2

3

INPUT

VCC

GND

2

DVD PCB

PCB130

VMC298

E

1

YUV OUT

J8103

E

4

H1

2 3

H2

5

H1

VIDEO OUT SW

SW8101

H

COMP

L

S/CVBS

Y/C SEPA

J8102

2

4 3

1

6 5

DVD AUDIO OUT

J8101

4

E

1

E

5

H1

2 3

H1 H2

TX

RX

P.CON+3.3V

P.CON+3.3V

GND

CP4002

1

2

3

4

5

GND

P.CON+5V

P.CON+9V A

6

7

8

P.CON+9V A

MOTOR GND

P.CON+12V

AT+5V

9

10

11

12

6

7

8

4

5

1

2

3

9

10

11

12

CP501

TX

RX

P.CON+3.3V

P.CON+3.3V

GND

GND

P.CON+5V

P.CON+9V A

P.CON+9V A

P.CON+12V

AT+5V

CP8102

DVD_RESET

SYS_MUTE

GND

3

DAC_D_DVD_VIDEO 4

5

1

2

DVD_AUDIO_L

GND

DVD_AUDIO_R

6

7

8

1

2

3

4

5

6

7

8

CD8002

FFC

6

5

8

7

4

3

2

1

CP8002

6

5

8

7

4

3

2

1

DVD_RESET

SYS_MUTE

DAC_D_DVD_VIDEO

GND

DVD_AUDIO_L

GND

DVD_AUDIO_R

AC120V_60HZ

CD501

WHITE

BLACK

S502 WHITE

S501 BLACK

VCR PCB

PCB010

VMC300

FRONT AV JACK

VIDEO

J8003

E

1

FRONT AV JACK

AUDIO L

J8004

FRONT AV JACK

AUDIO R

J8005

E

1

E

1

H

2

H

2

3

NC

2

H

REAR OUT JACK

J8001

E

1

E

4

3

H2

2

H1 H1

5

NC

NC

NC

NC

TU301

17 V.OUT

16

NC

15

TU 32V

14

SIF OUT

13 NC

12

AFT

11 DATA

10 CLOCK

9 NC

8

FSC

7

NC

5 V.IN

4

CONTROL

3 +B

2 CH

1 A.IN

CP3001 1

2

3

4

5

6

9

10

11

12

7

8

CAP FG

CAP VCO

VCC

CAP.M/F/R

I LIMIT

MOTOR GND

GND

LD/CY VCO

CAP CTL

LDM CTL

CYL FG/PG

CYL CTL

1

2

3

4

5

6

9

10

11

12

7

8

HALL

VCC

HALL

IN

OUT

SWITCH

LOGIC

CAPSTAN DD UNIT

M2001

RED WHITE

LM

LOADING MOTOR

M101

HF1 (R)

HF_COM

HF2 (L)

SP-CH1 (R)

SP_COM

SP-CH2 (L)

EP/LP-CH1 (R)

EP/LP COM

EP/LP-CH2 (L)

CP101

3

2

1

7

6

5

4

9

8

7

6

9

8

3

2

5

4

1

FPC

7

6

9

8

3

2

5

4

1

AUDIO REC

AUDIO PB

CTL+

CTL-

AE HEAD(-)

AE HEAD(+)

CP102

6

5

4

3

2

1

2

1

4

3

6

5

CD102

FFC

2

1

4

3

6

5

6

5

4

3

2

1

HEAD AUDIO CONTROL ASS’Y

H5001

AUDIO REC

AUDIO PB

CTL+

CTL-

AE HEAD(-)

AE HEAD(+)

UN4001

CYLINDER UNIT

HI-FI HEAD

SP HEAD

EP/LP HEAD

AUDIO

CONTROL

AE

1

A B

CAUTION

:SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES

DESCRIBED IN PARTS LIST ONLY

ARE

C D

ATTENTION

:LES PIECES REPAREES PAR UN ETANT

DANGEREUSES AN POINT DE VUE SECURITE

N’UTILISER QUE CELLS DECRITES

DANS LA NOMENCLATURE DES PIECES

E

NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE

F G

G-23

H

8

7

6

5

4

3

2

1

H

G-24

MPEG/MICON

10ns

100mV

1

MEMORY

5ns

20mV

2

RF AMP/DSP

200ns

20mV

3

200ns

10mV

4

AUDIO/VIDEO

500

µ s

100mV

5

500

µ s

100mV

6

WAVEFORMS

10

µ s

100mV

11

200ns

20mV

7

10

µ s

100mV

8

10

µ s

100mV

12

Y/C/AUDIO/CCD/HEAD AMP

PB

10

µ s

500mV

16

10

µ s

100mV

9

PB

100ns

100mV

17

10

µ s

100mV

10

PB

1ms

100mV

18

NOTE:

The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.

H-1

PB

200ms

500mV

19

REC

5

µ s

20V

20

SYSCON

PB

5ms

1.0V

21

PB

200

µ s

1.0V

22

POWER ON

50ns

1.0V

23

PB

500

µ s

1.0V

24

WAVEFORMS

5

µ s

500mV

38

POWER

PB

5ms

500mV

25

5

µ s

5.0V

39

PB

5ms

2.0V

27

HI-FI/DEMODULATOR

PB

10ms

1.0V

28

TUNER/JACK

10

µ s

200mV

32

NOTE:

The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.

H-2

MECHANICAL EXPLODED VIEW

206

206

206

206

123

202

202

203

112

121

105

PCB010

(VCR PCB ASS'Y)

104

103

106

113

118

120

209

125

115

103

102

114

106

204

203

117

201

209

206

107

209

126

113

124

110

203

203

PCB130

(DVD PCB ASS'Y)

205

207

108

109

205

111

205

119

203

122

203

101G

101C

101H

101D

101G

101F

101I

127

101A

101B

101I

101E

101

208

208

203

PCB270

(OPERATION PCB ASS'Y)

I1-1

116

203

CHASSIS EXPLODED VIEW (TOP VIEW)

505

CD1501

300

349

M2003

UN4001

AE

341

331

334

314

323

508

333

501

H5002

315

336

324

335

342

503

504

H5001

306

322

508

312

305

302

AB

AB

332

347

301

AA

313

AA

AA

AA

AB

CD1502

304

M101

318

AE

325

317

309

AA

AD

AC

AB

319

307

AC

320

AB

316

348

321

AE

AE

510

507

AB

506

346

AB

345

AB

CLASS

GREASE

PART NO.

Y315061000

Y315071000

Y31D011000

Y315041000

Y315141000

PART NAME

G-555G

MG-33

FG-84M

FL-721

G-313Y

MARK

AA

AB

AC

AD

AE

I2-1

NOTE:

Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section.

Check if the correct grease is applied for each position.

CHASSIS EXPLODED VIEW (BOTTOM VIEW)

308

509

344

327

343

328

326

AA

303

300

M2001

CD1501

338

502

AA

337

AA

502

AA

CD1502

AA

340

502

AA

AA

AD

329

311

AA

339

AA

310

AB

AB

AB

AA

505

330

CLASS

GREASE

PART NO.

Y315061000

Y315071000

Y31D011000

Y315041000

Y315141000

PART NAME

G-555G

MG-33

FG-84M

FL-721

G-313Y

MARK

AA

AB

AC

AD

AE

I2-2

NOTE:

Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section.

Check if the correct grease is applied for each position.

DVD DECK EXPLODED VIEW

AC

615

600

613

612

619

606

606

608

AA

AA

AA

618

AA

AC

604

610

CD2302

701

SW1

AD

617

AA

AC

705

603

AC

602

614

616

PCB640

605

SW2

(SW PCB ASS'Y)

703

704

CD2001

Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.

If the repair is needed, replace the

DVD MECHA ASS'Y.

605

601

702

607

AA

AA

621

M2002

CP1

PCB68A

(RELAY PCB ASS'Y)

622

623

AB

609

620

611

AA

CD2301

CLASS

GREASE

PART NO.

Y315061000

Y315121000

Y315131000

Y31D031000

PART NAME

G-555G

G-337F

SF-112

ORG-102

MARK

AA

AB

AC

AD

I3-1

NOTE:

Applying positions AA, AB, AC and AD for the grease are displayed for this section.

Check if the correct grease is applied for each position.

MECHANICAL REPLACEMENT PARTS LIST

201

202

203

204

205

206

207

208

209

120

121

122

123

124

125

126

127

---

---

---

---

---

---

---

---

102

103

104

105

106

107

108

109

115

116

117

118

119

110

111

112

113

114

REF. NO. PART NO.

101

101A

101B

101C

101D

101E

101F

101G

101H

101I

A2C510H720 CABINET,FRONT ASS'Y

701WPJC393 CABINET,FRONT

711WPDA628 PLATE,DISPLAY

712WPJB882 FLAP

713WPA0193 GLASS,LED-VCR

713WPA0194 GLASS,LED-DVD

735WPB0258 BUTTON,FRAME-DVD

735WPB0259 BUTTON,FRAME-VCR

743WKA0042 SPRING,FLAP

800WFA0051 CUSHION,LEG

DESCRIPTION

701WPA0686 HOLDER,DECK

701WPA0751 HOLDER,DECK

752WSA0230 SHIELD,CASE HEAD AMP

753WUAA006 SPRING,EARTH HEAD AMP

85OP700038 HOLDER,END SENSOR

702WSA0183 PLATE,BOTTOM

702WSAA073 PLATE,BOTTOM

722A08A142 SHEET,RATING

7230007673 SHEET,JACK

7232020748 SHEET,IC

7260000341 SHEET,CAUTION

752WSA0275 COVER,AC HEAD

752WSA0290 SHIELD,COMPO

800WFA0046 CUSHION

752WUAA001 SHIELD,3PIN

761WSA0127 ANGLE,FRONT

702WSB0086 CABINET,TOP

712WPB0162 PLATE,TRAY-FRONT

761WSA0130 ANGLE,DVD

10x15xT10 or

7235630001 SHEET,DVD(NEW)

761WPA0262 HOLDER,DECK TOP

8965TS1010 CUSHION 65TS 10-10H L=10

8965TS1017 CUSHION 65TS

761WPA0292 HOLDER,DVD

800WB00004 FIBER,WASHER 7x3.2xT0.5

752WSA0359 ANGLE,DVD 2

723000A698 SHEET,DISPLAY

8154730414 SCREW,TAP TITE(B)

8109130B94 SCREW,TAP TITE(B)R

8109230704 SCREW,TAP TITE(B)R

8109I30A04 SCREW,TAP TITE(B)

8109230804 SCREW,TAP TITE(B)

8109K30601 SCREW,TAP TITE(B)

8107130404 SCREW,TAP TITE(S)

8110226804 SCREW,TAP TITE(P)

810F130804 SEMS(F)

PAN

BIND

WH7

BIND

PAN

BIND

M3x41R

3x29

3x7

3x10

3x8

BIND(3D) 3x6

3x4

2.6x8

3x8

A2C510H975 INSTRUCTION BOOK KIT

723000C229 LABEL BOOMERANGIT

791WHA0100 GIFT,SHEET

792WHA0489 PACKAGE,FRONT

792WHA0515 PACKAGE,BACK

793WCDB930 GIFT BOX

795WCA0662 PAD,DVD/VR

795WCAA181 PAD,L

155x250

(340x480x160)

J1-1

CHASSIS REPLACEMENT PARTS LIST

330

331

332

333

334

335

336

337

338

339

325

326

327

328

329

320

321

322

323

324

345

346

347

348

349

340

341

342

343

344

REF. NO. PART NO.

300 A2C303N420K DECK ASSY

DESCRIPTION

A2C303N420K

310

311

312

313

314

315

316

317

318

319

301

302

303

304

305

306

307

308

309

85OA400240 PINCH ROLLER BLOCK (VA)

85OA500026 AHC ASS'Y

85OP200290 BELT,CAPSTAN (S)

85OP600581 WORM

85OP500083 BASE,AC HEAD

85OP800324 SPRING,AC HEAD

85OA000459 MAIN CHASSIS ASS'Y

85OA200089 CLUTCH ASS'Y

85OA200090 ARM IDLER ASS'Y

85OA300065 LOADING ARM S UNIT

85OA300066 LOADING ARM T UNIT

85OA400223 INCLINED BASE T UINT 3S

85OA400232 P5 ARM ASS'Y 2

85OA400235 TENSION ARM ASS'Y 2

85OA400231 INCLINED BASE S UNIT

85OP800367 SPRING LOCKER

85OP900736 CASS,HOLDER

85OP900748 CASS,SIDE L

85OP900749 CASS,SIDE R

85OP900739 LOCKER,R

85OA900228 LINK UNIT

85OP000496 POST,CASS GUIDE

85OP200316 REEL,S (S)

85OP200317 REEL,T (S)

85OP200308 GEAR,IDLER

85OP200311 GEAR,CLUTCH

85OP200312 GEAR,COUPLING

85OP200313 LEVER,CLUTCH

85OP300194 GEAR,MAIN LOADING

85OP400490 LEVER,TENSION

85OP400492 HOLDER,TENSION

85OP400520 CAP.P4

85OP400542 BAND,TENSION

85OP400533 CONNECT,TENSION

85OP600573 ARM,BRAKE T

85OP600584 BAND,BRAKE T

85OP600577 CAM,PINCH ROLLER

85OP600578 CAM,MAIN

85OP600579 ROD,MAIN

85OP600582 GEAR,JOINT

85OP800322 SPRING,TENSION

85OP800360 SPRING,BRAKE T

85OP800355 SPRING,COUPLING

85OP800356 SPRING,RING

85OP900750 LEVER,LINK 2

85OP900744 LEVER,FLAP

85OP900745 CASS,OPENER

85OP700035 REFLECTOR,LED

85OP900746 BRACKET,TOP 3V

REF. NO. PART NO.

501

502

503

DESCRIPTION

8107226804 SCREW,TAP TITE(S) BIND

83ETW30000 E-RING

8107226404 SCREW,TAP TITE(S) BIND

2.6x8

3

2.6x4

504

505

506

507

508

509

8102120604 SCREW,PAN

8109126604 SCREW,TAP TITE(B) PAN

810A130404 SCREW/WASHER(A)

M2x6

2.6x6

M3x4

810A126504 SCREW/WASHER(A)

82Q264713N POLYSLIDER WASHER

M2.6x5

2.6x4.7xT0.13

82P184505N POLYSLIDER WASHER(CUT) 1.8x4.5xT0.5

510 8107226604 SCREW,TAP TITE(S) BIND

CD1501

CD1502

H5001

H5002

122H071704 CORD JUMPER

122Y021902 CORD JUMPER

1523Q91003 HEAD (AUDIO CONTROL)

1543Q02014 HEAD (FULL ERASE)

! M101 1596P98001 MOTOR (LOADING)

1596S98001 MOTOR (LOADING)

1510S98038 CAPSTAN DD UNIT ! M2001

M2003

1510S98040 CAPSTAN DD UNIT

1589S11017 MICRO MOTOR

! UN4001 A2C301N500 CYLINDER UNIT ASS'Y

2.6x6

2H071704

2Y021902

VTR-1X2RPE22-756

VTR-1X2ERS11-154

MXN13FB12K3

MDB2B66

F2QVB33

F2QVB33B

I2OAL05

A2C301N500 or or

J2-1

DVD DECK REPLACEMENT PARTS LIST

REF. NO. PART NO.

600

DESCRIPTION

A5E602V650P DVD MECHA ASS'Y A5E602V650P

610

611

612

613

614

615

616

617

618

619

601

602

603

604

605

606

607

608

609

92P100022A TRAVERSE HOLDER

92P100080A RACK,FEED 1A

92P100081A RACK,FEED 2A

92P100035A LEVER,RACK FEED

92P200006A INSULATOR(F)

92P200007A INSULATOR(R)

92P100029A GEAR,FEED

92P300009A SPRING,RACK L

92P100028A GEAR,MIDDLE 3

92P300019A SPRING,RACK FEED 1A

92P100040A ARM,IDLER 2

92P000001A CLAMPER PLATE

92P100019A RACK,LOADING

92P100020A MAIN FRAME M

92P100021A TRAY

92P100023A GEAR,MAIN

92P100082A CLAMPER 2

92P300002A SPRING,RACK LOADING

92P400002A MAGNET,CLAMPER

620

621

622

623

92P100030A GEAR,IDLER

92P100025A GEAR,MOTOR

92P100083A GEAR,MIDDLE 1

92P100027A GEAR,MIDDLE 2

701

702

703

704

705

8110226804 SCREW,TAP TITE(P) BIND

8110120604 SCREW,TAP TITE(P) PAN

8107220504 SCREW,TAP TITE(S) BIND

8140117254 SCREW,PAN

8110220804 SCREW,TAP TITE(P) BIND

CD2001 122H0O1901 CORD JUMPER

CD2301

CD2302

CP1

122H080701

06CH232101

069JV80180

CORD JUMPER

CORD CONNECTOR

CONNECTOR PCB SIDE

! M2602 1515S98001 FEED MOTOR

PCB640 A5E601V640 PCB ASS'Y

PCB68A A5E601V680 PCB ASS'Y

SW1

SW2

0515S32001 SWITCH

0500101036 PUSH SWITCH

2.6x8

2x6

2x5

M1.7x2.5 P3

2x8

2H0O1901

2H080701

232101

IMSA-9615S-08C-PP

BCD3B81

BEC001A

BEC002A

SSS-23-6

ESE22MH22

J3-1

ELECTRICAL REPLACEMENT PARTS LIST

D2601

D3001

D3007

D3009

D8002

D8003

D8008

D8101

D8102

D8103

D8106

D8107

D8108

D8109

D8110

D8111

D8112

D8113

D532

D534

D535

D536

D537

D538

D539

D651

D656

D685

D701

D702

! D511

! D512

! D513

D514

! D515

D518

! D522

! D523

D524

D526

D528

D530

D531

! C501

! C502

! C505

! C511

C513

! C514

! C515

! C516

! C518

! C519

! C521

! C522

C525

! C540

REF. NO. PART NO.

! R501

! R502

! R512

DESCRIPTION

R E S I S T O R S

R0G3K2335K RC

R3X181R82J R,METAL OXIDE

R3X181683J R,METAL OXIDE

3.3M OHM 1/2W

0.82 OHM 1W

68K OHM 1W

! R516

! R517

! R545

R63581R22J R,FUSE

R002T2821J RC

R65584150J R,FUSE

E02LF2222M CE

CAPACITORS

P2122B104M CMP

0.22 OHM 1W

820 OHM 1/2W

15 OHM 1/4W

! D502

! D503

D504

! D505

! D506

! D507

D509

! D510

E02LU2101M CE

E62QFC470M CE

C0PLRR7H2K CC

E02LU2101M CE

C0J0B0514K CC

CD39E0MQ3M CC

E62F00222M CE

E02L01222M CE

E02LU2101M CE

E02LU5220M CE

C0PLRR7U2K CC

E62QFC470M CE

D I O D E S

D2WXN40050 DIODE SILICON

D2WXN40050 DIODE SILICON

D1VT001330 DIODE,SILICON

2200 UF 16V

0.1 UF 275V ECQUL

100 UF 16V

47 UF 200V

220 PF 2KV R

100 UF 16V

0.01 UF 500V B

0.0047UF 250V

2200 UF 6.3V

2200 UF 10V

100 UF 16V

22 UF 50V

680 PF 2KV R

47 UF 200V

IC101

! IC501

D2WXN40050 DIODE SILICON

D2WXN40050 DIODE SILICON

D23TGP15J0 DIODE SILICON

D2WXGP10J0 DIODE RECTIFIER

D97U02701B DIODE,ZENER

D97T02701D DIODE,ZENER

D28T21DQN4 DIODE SCHOTTKY

D28T21DQN4 DIODE SCHOTTKY

D2WXN40050 DIODE SILICON

D97U01201B DIODE,ZENER

D28T21DQN4 DIODE SCHOTTKY

D1VT001330 DIODE,SILICON

D28TELS6N6 DIODE RECTIFER

D97U03301B DIODE,ZENER

D1VT001330 DIODE,SILICON

D97U03R31B DIODE,ZENER

D1VT001330 DIODE,SILICON

D28TELS6N6 DIODE RECTIFER

D97U09R11B DIODE,ZENER

D97U03R31B DIODE,ZENER

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

0021E2Q140 LED

D2WXN40050 DIODE SILICON

0021E2Q140 LED

D1VT001330 DIODE,SILICON

D97U05R11B DIODE,ZENER

DDARDS1200 DIODE SILICON

0010E00330 INFRARED LED

D1VT001330 DIODE,SILICON

D1VT001330 DIODE,SILICON

D97U06R81B DIODE,ZENER

D97U06R81B DIODE,ZENER

D1VT001330 DIODE,SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

DDDRL41480 DIODE SILICON

I C S

I03F3206M0 IC

I1KJ9A4310 IC

1SS133T-77

1SS133T-77

1SS133T-77

1SS133T-77

LTL-1CHEE-002A

1N4005-EIC

LTL-1CHEE-002A

1SS133T-77

MTZJ5.1B T-77

KDS120RTK

LTE-3271T-012A-O

1SS133T-77

1SS133T-77

MTZJ6.8B T-77

MTZJ6.8B T-77

1SS133T-77

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

MCL4148

1N4005-EIC

1N4005-EIC

1SS133T-77

1N4005-EIC

1N4005-EIC

RGP15J-G23

RGP10J-EIC

MTZJ27B T-77

MTZJ27D T-77

21DQ04N-TA2B1

21DQ04N-TA2B1

1N4005-EIC

MTZJ12B T-77

21DQ04N-TA2B1

1SS133T-77

10ELS6N-TA1B2

MTZJ33B T-77

1SS133T-77

MTZJ3.3B T-77

1SS133T-77

10ELS6N-TA1B2

MTZJ9.1B T-77

MTZJ3.3B T-77

1SS133T-77

1SS133T-77

LA71206M-MPB

KIA431 or

Q664

Q665

Q666

Q2601

Q2602

Q2603

Q2604

Q2605

Q3001

Q3002

Q3003

Q3004

Q3005

Q652

Q653

Q654

Q655

Q656

Q657

Q658

Q659

Q660

Q661

Q662

Q663

Q3006

Q3007

Q3008

Q8003

Q8004

! Q504

! Q505

Q506

Q507

Q508

Q509

! Q510

! Q511

Q513

Q514

Q530

Q531

Q651

Q101

Q102

Q103

Q104

Q105

Q106

Q107

Q109

Q301

! Q501

! Q502

! Q503

REF. NO. PART NO.

! IC502

! IC503

IC701

DESCRIPTION

I C S

I1KA98R09A IC

000220001W PHOTO COUPLER

I01F63FBP0 IC

KIA78R09API

PS2561L1-1-V(W)

AN3663FBP

IC2301

IC2601

IC2602

IC3001

IC3003

IC3099

IC4001

IC4002

IC4003

IC4005

IC4007

I03F065600 IC

ICQK067070 IC

I07E00358F IC

I54F50138B IC

I9UF032310 IC

A2C509K015 IC

ICQK067620 IC

ICRJ0C04N0 IC

I5HJ004BF0 IC

I0GF9XZ010 IC

IF9J0164A7 IC

IF9J0164A6 IC

IF3J00HGT7 IC

ICMJ0800A7 IC

ICMJ0800A8 IC

I17F0742K0 IC IC7301

IC8005

IC8101

LA6560

ZR36707TQC

BA10358F-E2

OEC0138B

PST3231NR

AT24C04N-10SI-2.7

ZR36762

AT24C04N-10SI-2.7

or

S-24C04BFJ-TB

PQ070XZ01ZP

M12L64164A-7T

M12L64164A-6T or or

HY57V641620HGT-7

SST39VF800A-70-4C-EK

SST39VF800A-70-4C-EK-D

PCM1742KE/2K

MM1501XNRE

NJM4580M(TE1) or

I0UF015010 IC

I0QJ045800 IC

T R A N S I S T O R S

TCAA3875SY TRANSISTOR SILICON

TCAA3875SY TRANSISTOR SILICON

TPAAC05002 COMPOUND TRANSISTOR

KTC3875S_Y_RTK

KTC3875S_Y_RTK

TCAT032034 TRANSISTOR, SILICON

TAATA12660 TRANSISTOR,SILICON

TAAA1504SY TRANSISTOR SILICON

TAAA1504SY TRANSISTOR SILICON

TCAA3875SY TRANSISTOR SILICON

TCAA3875SY TRANSISTOR SILICON

KTC3203_Y-AT

KTA1266-AT(Y,GR)

KTA1504S_Y_RTK

KTA1504S_Y_RTK

KTC3875S_Y_RTK

KTC3875S_Y_RTK

TJXG5NC500 FET

TCAT032034 TRANSISTOR, SILICON

TCAT03209Y TRANSISTOR SILICON

STP5NC50FP

KTC3203_Y-AT

KTC3209_Y-AT

TAAT012714 TRANSISTOR, SILICON

TCAT03209Y TRANSISTOR SILICON

KTA1271_Y-AT

KTC3209_Y-AT

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TCAA3875SY TRANSISTOR SILICON

TCAA3875SY TRANSISTOR SILICON

KTC3875S_Y_RTK

KTC3875S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TCAT032034 TRANSISTOR, SILICON

TAAT01241Y TRANSISTOR SILICON

T8YJ2412K0 TRANSISTOR SILICON

T8YJ2412K0 TRANSISTOR SILICON

KTC3203_Y-AT

KTA1241_Y-AT

2SC2412KT146 R,S

2SC2412KT146 R,S

TCAA3875SY TRANSISTOR SILICON

T6YJ1037K0 TRANSISTOR,SILICON

TAAA1504SY TRANSISTOR SILICON

KTC3875S_Y_RTK

2SA1037AKT146R,S

KTA1504S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TAAA1504SY TRANSISTOR SILICON KTA1504S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TAAA1504SY TRANSISTOR SILICON KTA1504S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TAAA1504SY TRANSISTOR SILICON KTA1504S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TAAA1504SY TRANSISTOR SILICON KTA1504S_Y_RTK

TPAAC05002 COMPOUND TRANSISTOR KRA103SRTK

T67J1036K0 TRANSISTOR SILICON

T67J1036K0 TRANSISTOR SILICON

T27T030180 FET

T27T030180 FET

T27T030180 FET

0002700690 PHOTO COUPLER

0002700690 PHOTO COUPLER

2SA1036KT146

2SA1036KT146

2SK3018

2SK3018

2SK3018

RPI-303

RPI-303

TPAAC05002 COMPOUND TRANSISTOR KRA103SRTK

0002700680 PHOTO COUPLER RPI-352C40N

0002700680 PHOTO COUPLER RPI-352C40N

0000M00390 PHOTO TRANSISTOR ST-304L

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

0000M00390 PHOTO TRANSISTOR ST-304L

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)

J4-1

ELECTRICAL REPLACEMENT PARTS LIST

REF. NO. PART NO.

DESCRIPTION

TRANSISTORS

Q8005

Q8006

Q8007

Q8101

Q8102

TCAA3875SY TRANSISTOR SILICON

TCAA3875SY TRANSISTOR SILICON

KTC3875S_Y_RTK

KTC3875S_Y_RTK

TPAAC05002 COMPOUND TRANSISTOR KRA103SRTK

TCAA3875SY TRANSISTOR SILICON KTC3875S_Y_RTK

TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK

Q8103

Q8104

Q8105

Q8106

Q8107

! L501

L502

L505

! L506

L701

L702

L101

L102

L103

L105

L106

L107

L301

L703

L704

L3002

L3003

L4001

L8004

L8101

L8102

L8103

L8104

L8105

L8106

! T501

J8001

J8003

J8004

J8005

J8101

J8102

J8103

TPAAA05001 COMPOUND TRANSISTOR KRA101SRTK

TCAA3875SY TRANSISTOR SILICON KTC3875S_Y_RTK

TCAA3875SY TRANSISTOR SILICON KTC3875S_Y_RTK

TNAAD05001 COMPOUND TRANSISTOR KRC104SRTK

TCAA3875SY TRANSISTOR SILICON

COILS &TRANSFORMER

KTC3875S_Y_RTK

031626009R COIL,BIAS OSC

02167F101J COIL

0216A65R6K COIL

02167F101J COIL

02167F220J COIL

02167F220J COIL

02167F220J COIL

029T000107 COIL,LINE FILTER

02AHB0A0A4 CORE,FERRITE

02167F220J COIL

02167E220K COIL

02167F220J COIL

02167F220J COIL

02167F101J COIL

0216A6100K COIL

021W7A220K COIL

0216A6120K COIL

02167F2R2J COIL

0216A6470K COIL

02167F1R0K COIL

02167F1R0K COIL

02167F1R0K COIL

02167F1R0K COIL

02167FR33K COIL

02167FR33K COIL

060J401079 RCA JACK

060J401080 RCA JACK

060J421023 RCA JACK

060J411029 RCA JACK

SW651

SW652

SW653

SW654

SW655

SW685

SW686

SW687

SW688

063D700005 JACK

060J411024 RCA JACK

S W I T C H E S

0504101T34 SWITCH,TACT

0504101T34 SWITCH,TACT

0504101T34 SWITCH,TACT

0504101T34 SWITCH,TACT

0504101T34 SWITCH,TACT

0504R01T38 SWITCH TACT

0504R01T38

0504R01T38

0504R01T38

SWITCH TACT

SWITCH TACT

SWITCH TACT

SW689

SW690

0504R01T38

0504R01T38

SWITCH TACT

SWITCH TACT

SW3001 0508S11001 SWITCH (LEAF)

1626009

100 UH

5.6 UH

100 UH

22 UH

22 UH

22 UH

0R4A223F20

W5T_20*10*10A

22 UH

22 UH

22 UH

22 UH

100 UH

10 UH

22 UH

12 UH

2.2 UH

47 UH

1 UH

1 UH

1 UH

1 UH

0.33 UH

0.33 UH

0481260074 TRANSFORMER,SWITCHING 81260074

J A C K S

060J411018 RCA JACK MSP-213V1-432 PBSN

MSP-281V4-B

MSP-281V1-B

MSP-281V3-A

MSP-213V1-732_PBSN

MDC-070V

MSP-213V1-652 PBSN

EVQ21505R

EVQ21505R

EVQ21505R

EVQ21505R

EVQ21505R

EVQ11L05R

EVQ11L05R

EVQ11L05R

EVQ11L05R

EVQ11L05R

EVQ11L05R

LSA-1144EAU

SW8101 0510Y24001 SWITCH SLIDE

P.C.BOARD ASSEMBLIES

PCB010 A2C505H010 PCB ASS'Y

SK42H01G9A

VMC300A

PCB130 A2C505H130 PCB ASS'Y

PCB270 A2C503X270 PCB ASS'Y

MISCELLANEOUS

B501

B502

B2601

B2602

B2603

B2604

B2605

B4001

B4002

B4003

B4004

B4005

024HT03563 CORE,BEADS

024HT03553 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

VMC298A

VEBA07A

W4BRH3.5X6X1.0X2

W5RH3.5X5X1.0

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

REF. NO. PART NO.

B4006

B4007

B4008

DESCRIPTION

MISCELLANEOUS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

B7301

B7302

B8101

B8102

B8103

CD102

! CD501

CD681

CP101

CP102

CP103

CP501

CP651

CP681

069J750019 CONNECTOR PCB SIDE

069J750019 CONNECTOR PCB SIDE

CD6002 06CPL02006 CABLE

CD6003 06CPBA2003 CORD,RCA PIN

CD8002 122F080601 CORD JUMPER

CP2601 069GYOT079 CONNECTOR PCB SIDE

CP2602 069EV83010 CONNECTOR PCB SIDE

CP2603

CP3001

CP4002

CP8002

CP8102

! F501

FH501

069S230629

06972C0010

069S2C0629

CONNECTOR PCB SIDE

CONNECTOR PCB SIDE

CONNECTOR PCB SIDE

069J780599 CONNECTOR PCB SIDE

069J780599 CONNECTOR PCB SIDE

081PC2R505 FUSE

FH502

OS651

06710T0009 HOLDER,FUSE

06710T0006 HOLDER,FUSE

06710T0009 HOLDER,FUSE

06710T0006 HOLDER,FUSE

077Q037009 REMOTE RECEIVER

077Q037001 REMOTE RECEIVER

OS8101

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

024HC31022 CORE,BEADS

122H061504 CORD JUMPER

1209419910 CORD AC BUSH

122H051202 CORD JUMPER

0697290620 CONNECTOR PCB SIDE

069J760599 CONNECTOR PCB SIDE

067U002019 WIRE HOLDER

06CH2C0302 CORD CONNECTOR

TM601

! TU301

V651

X101

X3001

X3002

X4001

07AQ000009 OPTICAL DEVICE

07A9000006 OPTICAL DEVICE

076R0ET050 TRANSMITTER

0162300038 RF UNIT

0040H54010 LED DISPLAY

0040F54009 LED DISPLAY

100DT3R528 CRYSTAL

100BT01004 CRYSTAL

100DA32R01 CRYSTAL

100BT02701 CRYSTAL

ELF-4M6SDRVGWB/S423

HC-49/U

HC-49U/S

DT-26

HC-49U/S

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

FCM2012H-102T04

2H061504

9419910

2H051202

TOC-C09X-A1

IMSA-9604S-06C

B2013H02-2P

CH2C0302

IMSA-9604S-05Z13

IMSA-9604S-05Z13

CPL02006

TD-020301-3

2F080601

09-5000-024-001-006

00_6232_008_006_800

A2001WV2-3P

TMC-J12P-B2

A2001WV2-12P

IMSA-9604S-08C

IMSA-9604S-08C

51MS025L

EYF-52BCY

EYF-52BC

EYF-52BCY

EYF-52BC

PIC-37043LO-H

PIC-37043LO

OFTG038101

GP1FA553TZ

R25-1941

115-V-H015ARE

CO2D0M3-A or or or or or

RESISTOR

RC...................

CARBON RESISTOR

CAPACITORS

CC...................

CERAMIC CAPACITOR

CE...................

ALUMI ELECTROLYTIC CAPACITOR

CP...................

POLYESTER CAPACITOR

CPP.................. POLYPROPYLENE CAPACITOR

CPL.................. PLASTIC CAPACITOR

CMP................... METAL POLYESTER CAPACITOR

CMPL................ METAL PLASTIC CAPACITOR

CMPP................ METAL POLYPROPYLENE CAPACITOR

J4-2

SPEC.NO.

O/R NO.

M2C5-10H

K3Z2007

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement