CS80 SERVICE MANUAL Cinema Sound

CS80 SERVICE MANUAL Cinema Sound
Cinema Sound
CS80
CS480 Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797
Rev0
4/2007
CS80 (CS480 Subwoofer)
Note: The CS80 subwoofer is part of the CS480 system
Satellite loudspeakers CS480 order JBL part# CS400SATBG-E
Center channel CS480 order JBL part# CS600CENBG-E
- CONTENTS BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS
……..…………….……………..2
PACKAGING……………………………………….........................4
CONTROLS & CONNECTIONS.……………… …...…….……...5
OPERATION ………….……………………………..…………….6
EXPLODED VIEW/PARTS LIST……………...............................7
TEST SET-UP AND PROCEDURE……..…………….………….8
BLOCK DIAGRAM..…………………………………………………9
BASIC TROUBLESHOOTING…..…………….…..…..….……...11
120V ELECTRICAL PARTS LIST …………….…….…………..12
PCB DRAWINGS………………..………………………………...16
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS…………..22
120V SCHEMATICS.……….……………….………..…. ………23
BASIC SPECIFICATIONS
CS80 Subwoofer
Frequency Response (– 6dB):
35Hz – 160Hz
Amplifier Output:
125W RMS/250W Peak†
Driver:
8" (203mm)
Dimensions (H x W x D, including feet):
16-1/4" x 12" x 13-5/8" (413mm x 305mm x 346mm)
Weight:
29 lb (13.2kg)
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive
load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
CS80 (CS480 Subwoofer)
CS80SUB
LINE VOLTAGE
US 120VAC/60Hz
EU 230VAC/50-60Hz
125W Powered Sub/ Plate Amp
Yes/No
Yes
Yes
Hi/Lo Line
108-132
207-254
Specification
Unit
AB
G
4
8
8.22
100
105
AB
H
Ohms
in
Ohms
Watts
Watts
N/A
N/A
N/A
N/A
N/A
95
100
Average value - RMS Dynamic
power
98
Watts
Reference
@ Nominal input voltage
Dynamic power Highest Peak
121
Watts
Reference
@ Nominal input voltage
[email protected] Rated Power
THD @ 1 Watt
DC Offset
0.5
0.1
10
%
%
mV-DC
1
0.3
50
Damping factor
>150
DF
100
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
System Gain-LR input
50
14.4
9
42.85
Hz
mVrms
mVrms
dB
50
±2dB
±2dB
±2dB
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
90
85
65
dBA
dBr
dBr
Residual Noise Floor
1
mVrms(max)
Parameter
Amp Section
Type (120V Model)
Type (230V Model)
Load Impedance (woofer)
Woofer Size
System average impedance
Rated Output Power 120V
Rated Output Power 230V
Input Impedance
Line input L&R , LFE
Filters
Low Pass (fixed or variable)
Subsonic filter (HPF)
Limiter (yes/no)
Unit
Vrms
Vrms
Notes
Normal Operation
Normal Operation
QA Test Limits Conditions
Normal operation, MOMS required
Notes
120V System is Class AB
230V System is Class G
Minimum
Reference
10-500 Hz
@ Nominal input voltage
@ Nominal input voltage
3/20 50 Hz Burst unit driven 6dB above the
sensitivity to drive it into max power,
measured value is the average of the 4 first
consecutive peaks
Highest RMS of the first 4 consecutive
peaks
22K filter
22K filter
@ Speaker Output
Measured at amplifier board speaker out
terminals, Output power 90 Watts THD <
0.1 %
Nominal Freq.
To 1 Watt
To 1 Watt
Gain=130
Single input driven 1 input driven
LFE input driven only
Single input driven L or R
85
80
60
To Rated power
To Rated power
To 1 Watt
A-Weighting filter
22KHz filter
22KHz filter
1.5
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
>10
K ohms
N/A
Variable
-Hz
±2dB
±2dB
YES
--
N/A
Nominal over the audio BW
Refer to AP Graph
Reference only
Features
LFE Input
YES
Functional
Volume pot Taper (lin/log)
ATO
LOG
YES
--
Functional
Functional
Line In (L,R)
L ,R
--
Functional
Line level in LFE
LFE
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input Frequency
YES
50
-Hz
Functional
Functional
ATO Level Line Level in (L,R, LF
1.5
mV
Functional
ATO Turn-on time
<1
Sec
Functional
Auto Mute/ Turn-OFF Time
15
minutes
Functional
T before muting, after signal is removed
Power on Delay time
3
sec.
Functional
AC Power Applied
BW Limited to 500 Hz, refer to ECR00031
Input Configuration
RCA inputs: RED-WHT, L , R Summed to
Mono
Single connector
Functional
[email protected] into Line Input w/ 1 ch.
driven
Amp connected and AC on, then input
signal applied
2
Auto turn of time (T) must be 5 > T <15
CS80 (CS480 Subwoofer)
Parameter
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
Specification
Unit
QA Test Limits Conditions
5
50
50
mV-peak
mV-peak
mV-peak
10
100
100
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
12
Watts
13
@ nom. line voltage Unit active, no
signal applied (Green LED)
192 / 1.89
Watts/Amps
195 / 1.90
@ 120V-60 Hz (Nom.line voltage)
208 / 1.1
Watts/Amps
210 / 1.2
@ 230V-50 Hz (Nom.line voltage)
Notes
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Efficiency
Stand-by Input Power
Power Cons/[email protected]
power 120V Model
Power Cons/[email protected]
power230V Model
Protection
Short Circuit Protection
Thermal Protection
DC Offset Protection
Line Fuse Rating
120VAC
230VAC
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
100 Watts @ 4 Ohms nominal line voltage
100 Watts @ 4 Ohms nominal line voltage
YES
--
Functional
Direct short at output
65 deg. C
--
Functional
@1/8 max unclipped Power
YES
--
Functional
DC present at Speaker Out leads
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
2.5
1.25
Amps
Amps
Type-T or Slo Blo
Type-T or Slo Blo
External fuse with UL/SEMKO rated holder
External fuse with UL/SEMKO rated holder
3
CS80 (CS480 Subwoofer)
4
CS 480-120V om.qxd
12/15/06
4:43 PM
Page 10
CS80 (CS480 Subwoofer)
SUBWOOFER CONTROLS
Subwoofer Connections
If you have a Dolby® Digital or DTS® receiver/processor with
a low-frequency-effects (LFE) or subwoofer output:
Rear Panel
RECEIVER/PROCESSOR
SUBWOOFER OR
LFE OUTPUT
¡
PHASE
™
£
15' (4.5m)
Subwoofer
cable included
¢
If your receiver/processor does not contain a Dolby Digital or DTS
processor but has a subwoofer output:
∞
§
CS80SUB
RECEIVER/PROCESSOR
TSS-Sub800/230
FUSE
T 2.5A L 250V
120V–60Hz
200Watts
15' (4.5m)
Subwoofer cable
included
1 Subwoofer-Level Control
2 Phase Switch
NOTE: If your receiver/processor has only one sub out, you may use
either the L or R input.
3 LFE Input
4 Line-Level Inputs
Important!
5 Power Indicator LED
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF ALL
EQUIPMENT, including the subwoofer.
6 Power Switch
TSS-Sub800/230
5
CS 480-120V om.qxd
12/15/06
4:43 PM
Page 11
CS80 (CS480 Subwoofer)
OPERATION
Surround Modes
When using the CS480 in a Dolby Digital or DTS home theater system,
make sure all speakers are set to “Small”. In a Dolby Pro Logic® home
theater system, make sure the receiver’s center channel mode is set
to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and that
the speakers are set to “Small” in each mode.
Phase Control
The Phase Switch 2 determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers (0˚) or
opposite the main speakers (180˚). Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output at
the listening position.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets
on the back of the receiver.
Initially set the Subwoofer-Level Control 1 to the“MIN” position.
Turn on the subwoofer by pressing the Power Switch 6 on the
rear panel.
Turn on your entire audio system and start a CD or movie soundtrack
at a moderate level.
Auto On/Standby
With the Power Switch 6 in the ON position, the LED on the rear
panel 5 will remain lit in green or red to indicate the ON or STANDBY
mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch 6
can be left on. You may turn off the Power Switch 6 for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer-Level Control 1 up about halfway. If no sound
emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is
the AC plug connected to a “live” receptacle? Has the Power Switch
6 been pressed to the ON position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD or DVD. Use a
selection that has ample bass information.
Set the overall volume control of the receiver/processor to a comfortable level. Adjust the Subwoofer-Level Control 1 until you obtain
a pleasing blend of bass. Bass response should not overpower the
room but rather be adjusted so there is a harmonious blend across
the entire musical range. Many users have a tendency to set the
subwoofer volume too loud, adhering to the belief that a subwoofer is
there to produce lots of bass. This is not entirely true. A subwoofer is
there to enhance bass, extending the response of the entire system
so the bass can be felt as well as heard. However, overall balance
must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
6
CS80 (CS480 Subwoofer)
7
CS80 (CS480 Subwoofer)
CS80 Test Set Up and Procedure
Equipment needed:
•
•
•
•
Function/signal generator/sweep generator
Integrated Amplifier
Multimeter
Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) Turn the LEVEL control on the UUT to completely counterclockwise (MIN).
3) Turn on generator; adjust to 75mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full
clockwise (MAX)
5) LED should Green; immediate and vigorous bass response should be heard and felt from port tube
opening.
6) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
Sweep Function
1) Follow steps 1-5 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
CS80 (CS480 Subwoofer)
9
CS80 (CS480 Subwoofer)
10
CS80 (CS480 Subwoofer)
CS80 SUB (UL) AMP
Troubleshooting Flow Chart
AMP no signal out
no
yes
Check Fuse,Transformer,
D110, etc
Dc voltage check ±Vcc
yes
yes
no
Check Q117,118,119,D109 etc
Check+/-15VDC
yes
yes
LED red
LED light green or red
LED light green
Check,Q206,Q207,U203 etc
yes
yes
no
Check U202 pin14 signal
yes
Check U201
pin14 signal
yes
CheckU201,U202,VR201
VR202. etc
no
no
Check limiter board C304
Check U301,R343,R344 ,
C340,Q301,Q302, etc
yes
yes
Test R121,R122 signal
yes
Check ,+VCC& -VCC
no DC voltage
Check J123,J124 etc
no
yes
yes
Check RY101,D102,Q113,Q114 etc
Check Q107,Q108,Q105,
Q106,Q103,Q104,U101,etc
yes
no
Check U101,Q115,Q116,R138 etc
Set R138 to R140’S
Voltage is 0.51VDC
yes
yes
Check P102 signal
The Amp Ass’y OK, END
11
CS80 (CS480 Subwoofer)
CS80 120v Electrical parts List
Part Number
Description
Qty
Reference Designator
4.7K 1/4W ±5% CF 26mm (RoHS)
680Ω 1/4W ±5% CF26mm (RoHS)
100Ω 1/6W ±5% CF26mm (RoHS)
1K 1/6W ±5% CF 26m (RoHS)
10K 1/6W ±5% CF 26 (RoHS)
1M 1/6W ±5% CF 26mm (RoHS)
12K 1/6W ±5% CF 26mm (RoHS)
1.5K 1/6W ±5% CF 26mm (RoHS)
15K 1/6W ±5% CF 26mm (RoHS)
150K 1/6W ±5% CF 26mm (RoHS)
180Ω 1/6W ±5% CF26mm (RoHS)
1.8K 1/6W ±5% CF 26mm (RoHS)
22K 1/6W ±5% CF 26mm (RoHS)
3.3K 1/6W ±5% CF 26mm (RoHS)
3.9K 1/6W ±5% CF 26mm (RoHS)
39K 1/6W ±5% CF 26mm (RoHS)
47Ω 1/6W ±5% CF 26mm (RoHS)
470Ω 1/6W ±5% CF26mm (RoHS)
4.7K 1/6W ±5% CF 26mm (RoHS)
47K 1/6W ±5% CF 26mm (RoHS)
56Ω 1/6W ±5% CF 26mm (RoHS)
56K 1/6W ±5% CF 26mm (RoHS)
6.8K 1/6W ±5% CF 26mm (RoHS)
2.2Ω 1/2W ±5% 15mm (RoHS)
330Ω 2W ±5% 5mm(RoHS)
0.1Ω 5W ±5% stand (RoHS)
3K 0.3W ±20%(RoHS)
820Ω 1W ±5% 10mm (RoHS)
2
2
1
1
1
1
2
6
4
1
2
1
3
3
2
1
4
1
3
1
1
1
1
1
2
2
1
1
R147,R150,
R148,R151,
R120,
R124,
R134,
R143,
R135,R139,
R103,R123,R136,R137,R141,R142,
R118,R145,R152,R154
R131,
R111,R114,
R153,
R128,R129,R133,
R106,R107,R144,
R105,R108,
R126,
R112,R113,R115,R116
R140,
R110,R125,R130,
R101,
R117,
R104,
R109,
R127,
R146,R149
R121,R122
R138,
R132,
DISC CAPACITOR 1000P 50V ±10% (RoHS)
DISC CAPACITOR 0.1U 50V +80/-20% (RoHS)
DISC CAPACITOR 0.047U 50V ±20% (RoHS)
DISC CAPACITOR 100P 50V SL ±10% (RoHS)
MYLAR CAPACITOR 0.1U 50V ±5% (RoHS)
MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS)
ELECTROYTIC CAP.1U 50V ±20% (RoHS)
ELECTROYTIC CAP.100uF 16V ±20% (RoHS)
ELECTROYTIC CAP.22U 50V ±20% (RoHS)
ELECTROYTIC CAP.220U 10V ±20% (RoHS)
ELECTROYTIC CAP.220U 16V ±20% (RoHS)
ELECTROYTIC CAP.47U 25V ±20% (RoHS)
MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS)
ELECTROYTIC CAP.100uF 16V ±20% (RoHS)
ELECTROYTIC CAP.6800U/50V ±20%D25X45mm (RoHS)
1
4
1
2
1
4
2
3
2
2
1
1
2
1
2
C116,
C108,C113,C115,C119
C106,
C139,C140,
C107,
C124,C125,C126,C128
C105,C112,
C109,C117,C120,
C114,C118,
C129,C130,
C111,
C103,
C123,C127
C110,
C121,C122
TRANSISTOR 2SC1815GR TOSHIBA(RoHS) NPN
TRANSISTOR 2SA1015GR TOSHIBA (RoHS) PNP
*TRANSISTOR FSC 2N5551 (RoHS) NPN
TRANSISTOR FSC 2N5401 AI-PNP350V 500mA TO-92
DIODE 500mW 75V 1N4148 Panjit (RoHS)
ZENER Diode GDZJ3.3A 500mW 3.3V 2% 26mm (RoHS)
ZENER DIODE GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS)
ZENER DIODE GDZJ16C 500mW 16V 26mm 2% (RoHS)
TRANSISTOR TIP35C (RoHS) NPN
5
2
2
2
4
1
2
1
1
Q102,Q111,Q112,Q113,Q118,
Q114,Q116,
Q103,Q109,
Q104,Q110,
D101,D103,D105,D108
D102,
D106,D107,
D109,
Q107,
Main Amp PCB
Resistors
110-14472j26-E
110-14681j26-E
110-16101j26-E
110-16102j26-E
110-16103j26-E
110-16105j26-E
110-16123j26-E
110-16152j26-E
110-16153j26-E
110-16154j26-E
110-16181j26-E
110-16182j26-E
110-16223j26-E
110-16332j26-E
110-16392j26-E
110-16393j26-E
110-16470j26-E
110-16471j26-E
110-16472j26-E
110-16473j26-E
110-16560j26-E
110-16563j26-E
110-16682j26-E
110-122r2j15-E
110-20331jk2-E
113-50r10j10-E
114-03302m0-E
110-10821jk2-E
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
Capacitors
130-2b102k503-E
130-3f104z503-E
130-3f473m503-E
130-sl101k503-E
132-104j503-E
132-223ja03-E
135-3105m50-E
135-3107m16-E
135-3226m50-E
135-3227m10-E
135-3227m16-E
135-3476m25-E
132-223ja03-E
135-3107m16-E
135-4688m50-E
Semiconductors
192-027c1815gr-E
192-028a1015gr-E
192-1572n5551-E
192-1582n5401-E
197-631n4148-E
199-65000333g-E
199-65000623g-E
199-65001603g-E
192-021tip35c-E
12
CS80 (CS480 Subwoofer)
Part Number
Description
Qty
Reference Designator
Main Amp PCB
192-022tip36c-E
192-027c1815gr-E
192-201d882y-E
192-202b772y-E
192-991d669a-E
192-992b649t-E
197-00kbl405-E
197-101n4002-E
190-06m4558d-E
TRANSISTOR TIP36C (RoHS) PNP
TRANSISTOR 2SC1815GR TOSHIBA(RoHS)
TRANSISTOR KSD882Y PNP
TRANSISTOR KSB772Y PNP
TRANSISTOR HI-SINCERITY HSD669A NPN
TRANSISTOR HSB649T PNP
Bridge Diode 4A 500V KBL405(RoHS)
DIODE 1N4002TB (RoHS)
IC OPA 4558D DUAL OP-AMP
1
2
1
1
1
1
1
1
1
26AWG 1007 200mm RED 3mm (RoHS)
*relay 5A 24V UDH-SS124D(RoHS)
COUPLER 7PIN PITCH=2.5mm(RoHS)
COUPLER 2PIN PITCH=3.96mm(RoHS)
1
1
1
1
1
2
1
1
4
1
2
Q108,
Q101,Q115
Q117,
Q119,
Q106,
Q105,
D110,
D104,
U101,
Miscellaneous
162-10202001-E
171-udhss124d-E
175-1c07v01-E
175-1d02v01-E
175-1d03v01-E
193-3m2520-E
323-AL-00020-0LAE
COUPLER 3 PIN PITCH=3.96mm JST-VH peel off PIN (RoHS)
*mica piece TO-3P 25x20mm (RoHS)
HEAT SINK 65*32*31 aluminium
351-AM03014A094-E M3*14 MACHINE SCREW crossover BLACK (RoHS)
352-AM03008D040-E ¢3*8 B TYPE PING SCREW Crossover, BLACK (RoHS)
361-FE-00051-0LAE TRANSISTOR holder 14.2*8.0*5.2t=1.6mm (RoHS)
361-NYL-00054-0LAE TRANSISTOR sheet (SW06002) (RoHS)
RY101,
P101,
P102,
P103,
for Q107,Q108
Input/Preamp PCB
Resistors
110-16102j26-E
RESISTOR 1K 1/6W ±5% CF 26mm (RoHS)
5
110-16103j26-E
RESISTOR 10K 1/6W ±5% CF 26mm (RoHS)
12
110-16104j26-E
110-16105j26-E
110-16122j26-E
110-16124j26-E
110-16153j26-E
110-16154j26-E
110-16183j26-E
110-16205j26-E
110-16223j26-E
110-16273j26-E
110-16333j26-E
110-16334j26-E
110-16472j26-E
110-16473j26-E
110-16512j26-E
110-16513j26-E
115-h503a104-E
RESISTOR 100K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 1M 1/6W ±5% CF 26mm (RoHS)
RESISTOR 1.2K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 120K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 15K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 150K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 18K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 2M 1/6W ±5% CF 26m m (RoHS)
RESISTOR 22K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 27K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 33K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 330K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 47K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 5.1K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 51K 1/6W ±5% CF 26mm (RoHS)
Variable RESISTOR D16 50K/1 A (RoHS)
2
1
1
1
1
1
2
1
3
2
1
1
2
1
3
1
1
130-2b221k503-E
DISC CAPACITOR 220P 50V ±10% (RoHS)
9
130-3f104z503-E
130-ch220k503-E
132-103j503-E
132-104j503-E
132-223ja03-E
132-473j503-E
135-3105m50-E
DISC CAPACITOR 0.1U 50V +80/-20% (RoHS)
DISC CAPACITOR 22PF CH 50V±10 % (RoHS)
MYLAR CAPACITOR 0.01uF 50V ±5% (RoHS)
MYLAR CAPACITOR 0.1U 50V ±5% (RoHS)
MYLAR CAPACITOR 0.022uF 100V ±5% (RoHS)
MYLAR CAPACITOR 0.047U 50V ±5% (RoHS)
ELECTROYTIC CAP.1U 50V ±20% (RoHS)
7
1
2
3
1
2
1
135-3106m50-E
ELECTROYTIC CAP.10uF 50V ±20% (RoHS)
8
R213,R214,R215,R254,R253,
R212,R216,R217,R220,R221,R222,R225,R2
28,R226,R232,R235,R240,
R231,R266,
R259,
R264,
R233,
R234,
R251,
R262,R227,
R257,
R238,R250,R255,
R223,R237,
R249,
R252,
R258,R260,
R219,
R211,R229,R230,
R224,
VR201,
Capacitors
13
C207,C208,C210,C211,C212,C214,C220,C2
30,C249,
C232,C242,C244,C245,C246,C252,C254,
C229,
C223,C224,
C218,C221,C222,
C215,
C216,C217,
C228,
C206,C213,C219,C231,C241,C243,C251,
C253,
CS80 (CS480 Subwoofer)
Part Number
Description
Qty
Reference Designator
Input/Preamp PCB
135-3107m16-E
135-3226m50-E
ELECTROYTIC CAP.100uF 16V ±20% (RoHS)
ELECTROYTIC CAP.22U 50V ±20% (RoHS)
2
1
C233,C234,
C225,
TRANSISTOR 2SC1815GR TOSHIBA (RoHS) NPN
DIODE 500mW 75V 1N4148 Panjit (RoHS)
ZNR DIODE GDZJ5.1B 500mW 5.1V 2% 26mm 1N5231B
IC OPA 4558D DUAL OP-AMP
I.C TL074CN ST (RoHS) QUAD OP-AMP
LED 204HGW 3¢(RoHS) DUAL COLOR
2
7
1
1
2
1
Q206,Q207,
D201,D202,D207,D208,D211,D212,D214,
D213,
U203,
U201,U202,
D209,
WIRE ASS'Y 2PIN 150mm white/red (RoHS)
JACK RCA-326 (RoHS)
SWITCH SLIDE 6PIN MS7210V(RoHS) PHASE
PCB bracket 11.75*8.5*12.5H(RoHS)
1
1
1
1
D209,
JK202,
SW301,
110-16103j26-E
162-50289001-E
162-80098201-E
175-9f40hr2-E
190-16tl074cn-E
197-631n4148-E
RESISTOR 10K 1/6W ±5% CF 26mm (RoHS)
CABLE ASS'Y 280mm AWG26 WHT (RoHS)
WIRE 90mm grey 28AWG (RoHS)
COUPLER 40PIN PITCH=2.54mm HR2*40 (RoHS)
I.C TL074CN ST (RoHS) QUAD OP-AMP
DIODE 500mW 75V 1N4148 Panjit (RoHS)
1
1
1
R320
1
1
110-16103j26-E
RESISTOR 10K 1/6W ±5% CF 26mm (RoHS)
8
110-16183j26-E
110-16223j26-E
110-16273j26-E
110-16333j26-E
110-16472j26-E
110-16474j26-E
110-16751j26-E
110-16755j26-E
130-3f104z503-E
132-103j503-E
135-3226m50-E
135-3476m25-E
192-027c1815gr-E
197-631n4148-E
RESISTOR 18K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 22K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 27K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 33K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 4.7K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 470K 1/6W ±5% CF 26mm (RoHS)
RESISTOR 750Ω 1/6W ±5% CF 26mm (RoHS)
RESISTOR 7.5M 1/6W ±5% CF 26mm (RoHS)
DISC CAPACITOR 0.1U 50V +80/-20% (RoHS)
MYLAR CAPACITOR 0.01uF 50V ±5% (RoHS)
ELECTROYTIC CAP.22U 50V ±20% (RoHS)
ELECTROYTIC CAP.47U 25V ±20% (RoHS)
TRANSISTOR 2SC1815GR TOSHIBA (RoHS) NPN
DIODE 500mW 75V 1N4148 Panjit (RoHS)
1
2
1
1
2
1
2
1
2
2
2
1
2
2
Ferrite Core U-16.3*8.2*13 (J70)+CASE (RoHS)
DISC CAPACITOR 4700P 400V ± 20% (RoHS)
TRANSFORMER EI-86 60Hz 120V TT0869906580
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
Semiconductors
192-027c1815gr-E
197-631n4148-E
199-65000513g-E
190-06m4558d-E
190-16tl074cn-E
195-10204hgw-E
Miscellaneous
162-50159201-E
174-0rca326p-E
180-tms7210v-E
362-FE-00041-0LAE
Limiter PCB
to SW301,
P301,
U301,
D303
R301,R303,R304,R308,R309,R314,R340,
R344,
R302,
R310,R312,
R341,
R305,
R342,R343,
R307,
R311,R313,
R306,
C305,C306,
C302,C303,
C301,C340,
C304,
Q301,302
D301,D302,
MISCELLANEOUS
123-14j70d-E
130-3f472md00-E
150-E8604107-E
152-u602015-E
154-u25006t0-E
155-520020-E
156-h200040-E
156-h200050-E
162-10151001-E
166-a045a4bf-E
176-wjcE1-E
180-prf1003s-E
302-AL-05090-1LCE
POWER CORD JOINT HETEROPOLARITY SVT FT-2 6FT (RoHS)
FUSE 2.5A 250V 20mm (RoHS)
FUSE HOLDER R3-11 (RoHS)
THERMAL SHRINKABLE SLEEVING 20ψ*40mm (RoHS)
THERMAL SHRINKABLE SLEEVING 20Φ 50mm (RoHS)
WIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS)
HORN WIRE 450mm RED=205# 0.5T BLK=110#0.5T UL1015 18AWG
WIRE CONNECTOR PIN CE-1 (RoHS)
POWER SWITCH ROCK RF-1003-BB2-OHA (RoHS)
REAR BOARD 300*200*2.5T CSC80 120V USE (RoHS)
306-ABS-00177-0BAE REAR HOUSING 198*298*102mm (RoHS)
311-ABS-00028-0BAE PLASTIC KNOB 46077-W SOFT MATERIAL P.V.C. (RoHS) LEVEL
320-RUB-00033-0BAE RUBBER GASKET 25*21*4t GLUE ON BACK (RoHS)
14
C001
CS80 (CS480 Subwoofer)
Part Number
Description
Qty
MISCELLANEOUS
323-AL-00141-0LAE HEAT SINK 117.5*71.5*25 (RoHS)
333-EVA-00783-0BAE GASKET W 198*12*2.0T (RoHS)
333-EVA-00807-0BAE GASKET L 274*12*2.0T (RoHS)
333-EVA-00826-0BAE GASKET W 198*12*1.0T (RoHS)
333-EVA-00835-0BAE GASKET L 274*12*1.0T (RoHS)
335-NYL-05015-0BAE WIRE CLIP SB4F-2 BLACK (RoHS)
337-CU-00101-0LAE COPPER FILM 65L*50W (RoHS)
350-EM04012D024-E 4*12WOOD SCREW ELECTRICAL BLACK (RoHS)
351-AM03008A079-E M3*8 MACHINE SCREW ELECTRICAL BLACK (RoHS)
351-HM04016A218-E M4*16 MACHINE SCREW ELECTRICAL BLACK (RoHS)
352-AM03008D040-E 3*8 B TYPE PING SCREW ELECTRICAL BLACK (RoHS)
352-AM03010D065-E 3*10 P TYPE PING SCREW ELECTRICAL BLACK (RoHS)
354-GM04002-E
M4 NUT GASKET ELECTRICAL BLACK (RoHS)
362-FE-00013-0LAE PCB SUPPORT L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS)
15
1
2
2
2
2
2
1
4
7
4
8
1
4
2
Reference Designator
CS80 (CS480 Subwoofer)
16
CS80 (CS480 Subwoofer)
17
CS80 (CS480 Subwoofer)
18
CS80 (CS480 Subwoofer)
19
CS80 (CS480 Subwoofer)
20
CS80 (CS480 Subwoofer)
21
CS80 (CS480 Subwoofer)
22
CS80 (CS480 Subwoofer)
This section not present in CS80
23
CS80 (CS480 Subwoofer)
24
CS80 (CS480 Subwoofer)
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement