CS100 SERVICE MANUAL Cinema Sound

CS100 SERVICE MANUAL Cinema Sound
Cinema Sound
CS100
CS6100 Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797
Rev0
5/2007
CS100 (CS6100 Subwoofer)
Note: The CS100 subwoofer is part of the CS6100 system
Satellite loudspeakers CS6100 order JBL part# CS600SATBG-E
Center channel CS6100 order JBL part# CS600CENBG-E
- CONTENTS BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS
……..…………….……………..2
PACKAGING……………………………………….........................4
CONTROLS & CONNECTIONS.………………………………….5
OPERATION ………….……………………………..…………….6
EXPLODED VIEW/PARTS LIST…………………………………..7
TEST SET-UP AND PROCEDURE……..…………….………….8
BLOCK DIAGRAM..…………………………………………………9
BASIC TROUBLESHOOTING…..…………….…..…..….……...10
120V ELECTRICAL PARTS LIST ……………………………….11
PCB DRAWINGS………………..………………………………...15
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS…………..19
120V SCHEMATICS.……….……………….………..…. ………20
BASIC SPECIFICATIONS
CS100 Subwoofer
Frequency Response (– 6dB):
30Hz – 120Hz
Amplifier Output:
150W RMS/300W Peak†
Driver:
10" (254mm)
Dimensions (H x W x D, including feet):
18-1/2" x 12-3/4" x 15" (470mm x 324mm x 381mm)
Weight:
41 lb (18.6kg)
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a
resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
CS100 (CS6100 Subwoofer)
CS100SUB
LINE VOLTAGE
US 120vac/60Hz
EU 230vac/50-60Hz
Parameter
150W Powered Sub/ Plate Amp
Yes/No
Yes
Yes
Hi/Lo Line
108-132
207-264
Unit
Vrms
Vrms
Notes
Normal Operation
Normal operation, MOMS required
Specification
Unit
QA Test Limits
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
[email protected] Rated Power
THD @ 1 Watt
DC Offset
D
4
150
0.08
0.1
10
D
Ohms
Watts
%
%
mV-DC
n/a
n/a
145
1
0.5
20
Nominal
1 input driven
22K filter
22K filter
@ Amplifier Output
Damping factor
>100
N/A
15
50Hz-4 Ohms load
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
Line Input (L & R) Gain
LFE Input Gain
50
19.42
10.2
40.25
45.84
Hz
mVrms
mVrms
dB
dB
50
±2dB
±2dB
±1dB
±1dB
100
90
60
dBA
dBr
dBr
85
80
60
Residual Noise Floor
1
mVrms
2
Residual Noise Floor
1
mVrms(max)
2
Input Impedance
Line input L&R , LFE
>10
K ohms
n/a
Filters
Left & Right Low Pass fixed
Order & Q
LFE Low Pass fixed
Order & Q
Subsonic filter (HPF)
Order & Q
Hz
4th
Hz
2nd
Hz
2nd
-dB/Octave
-dB/Octave
-dB/Octave
±2dB
n/a
±2dB
n/a
±2dB
n/a
Limiter (yes/no)
YES
--
n/a
Features
LFE Input
Phase Switch (yes/no)
Volume pot Taper (linear/log
ATO (Auto-ON)
YES
YES
LOG
YES
Functional
Functional
Functional
Functional
BW limited to 500 Hz, refer to ECR00031
---
Input Configuration
Line In (L,R)
Line level in LFE
L ,R
LFE
Functional
Functional
RCA inputs: L , R
Signal to Noise
SNR-A-Weighted
SNR-Un-weighted
SNR @ 1W-Un-weighted
--
Conditions
Notes
Measured at amplifier PCB speaker out
connector @ 135 Watts into rated
impedance.
Nominal Freq.
To 1 Watt
To 1 Watt
1 input driven
1 input driven
LFE input driven only
1 input driven
LFE input driven only
rel. to rated power
rel. to rated power
rel. to 1W Output
Volume @max, using RMS reading
DMM/VOM (or A/P)
A-Weighting filter
22K filter
22K filter
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Nominal
Signal Sensing (ATO)
ATO test Frequency
50
Hz
ATO Line Level
2
mV
Functional
[email protected] into Line Input w/ 1 ch.
driven
ATO Turn-on time
5
ms
Functional
Amp connected and AC on, then input
signal applied in excess of 2mV applied
Auto Mute/ Turn-OFF Time
15
minutes
Functional
T before muting, after signal is removed
Power on Delay time
3
sec.
Functional
AC Power Applied
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
5
50
50
mV-peak
mV-peak
mV-peak
10
100
100
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
2
Auto turn off time (T) must be
5min > T <15min
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
CS100 (CS6100 Subwoofer)
Parameter
Specification
Unit
QA Test Limits
Conditions
Stand-by Input Power
12
Watts
16
@ nom. line voltage
Power [email protected] power
Efficiency
250
>60
Watts
%
250
>60
@ nom. line voltage
@ nom. line voltage
Notes
Efficiency
Protection
Short Circuit Protection
YES
--
Functional
Direct short at output
65 deg. C
--
Functional
@1/8 max unclipped Power
YES
--
Functional
DC present at Speaker Out leads
120VAC
3.15
Amps
230VAC
1.6
Amps
Thermal Protection
DC Offset Protection
AC Line Fuse Rating
Type-T or Slo Blo, Fuse markings
T3.15A, 250V
Type -T, Low breaking capacity,
Fuse markings T1.6AL, 250V
3
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
150 Watts @ 4 Ohms nominal line voltage
150 Watts @ 4 Ohms nominal line voltage
Back panel temperature rise should not
exceed 35K rise.
Relay or crowbar (for driver/fire protection)
External fuse with UL/SEMKO rated holder
External fuse with UL/SEMKO rated holder
CS100 (CS6100 Subwoofer)
PACKAGING
4
CS6100-120V om.qxd
12/15/06
4:26 PM
Page 10
CS100 (CS6100 Subwoofer)
SUBWOOFER CONTROLS
Subwoofer Connections
If you have a Dolby® Digital or DTS® receiver/processor with a
low-frequency-effects (LFE) or subwoofer output:
Rear Panel
RECEIVER/PROCESSOR
SUBWOOFER OR
LFE OUTPUT
15' (4.5m)
Subwoofer cable
included
If your receiver/processor does not contain a Dolby Digital or DTS
processor but has a subwoofer output:
RECEIVER/PROCESSOR
POWER
CS100SUB/230
§
AC 220V -230
V
z
50Hz-60H
250 W att
s
15' (4.5m)
Subwoofer cable
included
C A U TIO
N
1 Phase Switch
R IS K O F E LE C TR IC S H O C K
D O N O T O PEN
2 LFE Input
3 Line-Level Inputs
"W ARNING :FO R CO NTINUED
PRO TECTIO N AG AINST RISK
O F FIRE,REPLACE O NLY W ITH
SAM E TYPE T 1.6A L/250V FUSE"
"AVERTISSEM ENT:UTILISEZ UN
FUSIBLE DE RECHANG E DE M EM E
TYPE T 1.6A L/250V"
4 Power Indicator LED
T 1.6AL/25
0V
NOTE: If your receiver/processor has only one sub out, you may use
either the L or R input.
5 Subwoofer-Level Control
6 Power Switch
Important!
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
POWER
CS100SUB/230
§
AC 220V -230
V
50Hz60Hz
250 W att
s
C A U TIO N
R IS K O F E LE C TR IC S H O C K
D O N O T O PEN
"W ARNING :FO R CO NTINUED
PRO TECTIO N AG AINST RISK
O F FIRE,REPLACE O NLY W ITH
SAM E TYPE T 1.6A L/250V FUSE"
"AVERTISSEM ENT:UTILISEZ UN
FUSIBLE DE RECHANG E DE M EM E
TYPE T 1.6A L/250V"
5
T 1.6AL/25
0V
CS6100-120V om.qxd
12/15/06
4:26 PM
Page 11
CS100 (CS6100 Subwoofer)
OPERATION
Surround Modes
When using the CS6100 speakers in a Dolby Digital or DTS home
theater system, make sure all speakers are set to “Small”. In a
Dolby Pro Logic® home theater system, make sure the receiver’s
center channel mode is set to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and
that the speakers are set to “Small” in each mode.
Phase Control
The Phase Switch 1 determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers (0˚) or
opposite the main speakers (180˚). Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output
at the listening position.
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets
on the back of the receiver.
Initially set the Subwoofer-Level Control 5 to the“MIN” position.
Turn on the subwoofer by pressing the Power Switch 6 on the
rear panel.
Turn on your entire audio system and start a CD or movie soundtrack
at a moderate level.
Auto On/Standby
With the Power Switch 6 in the ON position, the LED on the rear
panel 4 will remain lit in green or red to indicate the ON or STANDBY
mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch 6
can be left on. You may turn off the Power Switch 6 for extended
periods of nonoperation, e.g., when you are away on vacation.
Adjust Level
Turn the Subwoofer-Level Control 5 up about halfway. If no sound
emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is
the AC plug connected to a “live” receptacle? Has the Power Switch
6 been pressed to the ON position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD or DVD. Use a
selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
comfortable level. Adjust the Subwoofer-Level Control 5 until you
obtain a pleasing blend of bass. Bass response should not overpower
the room but rather be adjusted so there is a harmonious blend
across the entire musical range. Many users have a tendency to
set the subwoofer volume too loud, adhering to the belief that a
subwoofer is there to produce lots of bass. This is not entirely true.
A subwoofer is there to enhance bass, extending the response of
the entire system so the bass can be felt as well as heard. However,
overall balance must be maintained or the music will not sound
natural. An experienced listener will set the volume of the subwoofer
so its impact on bass response is always there but never obtrusive.
6
9
CS100 (CS6100 Subwoofer)
EXPLODED VIEW
7
CS100 (CS6100 Subwoofer)
CS100 Test Set Up and Procedure
Equipment needed:
•
•
•
•
Function/signal generator/sweep generator
Integrated Amplifier
Multimeter
Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). Phase switch position does not
matter.
3) Turn on generator; adjust to 100mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. Turn LEVEL control full
clockwise (MAX)
5) LED should Green; immediate and vigorous bass response should be heard and felt from port tube
opening.
6) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
Sweep Function
1) Follow steps 1-5 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.4 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
CS100 (CS6100 Subwoofer)
9
CS100 (CS6100 Subwoofer)
CS100 SUB (UL) AMP
Troubleshooting Flow Chart
AMP no signal out
no
yes
Check Fuse,Transformer,
D501, etc
Dc voltage check ±Vcc
yes
yes
no
Check Q501.Q502.Q503,D502 etc
Check+/-15VDC
yes
yes
LED red
LED light green or red
LED light green
Check,Q206,Q207,U203 etc
yes
yes
Check U201
pin1 signal
no
Check U202 pin8 signal
yes
yes
CheckU201,U202,VR201
etc
no
no
Check limiter Circuit C317
yes
yes
no
Test R147 signal
Check U301,R343,R344 ,
C340,Q301,Q302, etc
Check ,+VCC& -VCC
DC voltage
yes
yes
Check RY101,D110,Q112,Q113 etc
Check CLASS 150W
MODEL
yes
no
Check Q107,Q108,Q109 etc
Check TH1
yes
yes
Check M100 signal
The Amp ass’y OK, END
10
CS100 (CS6100 Subwoofer)
CS100 120v Electrical parts List
Part Number
Description
Qty Reference Designato
Input/Preamp PCB
Resistors
110-16102j26-e
Resistor 1K 1/6W ±5% CF 26mm (RoHS)
110-16103j26-e
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
110-16104j26-e
110-16105j26-e
110-16122j26-e
110-16124j26-e
110-16153j26-e
110-16183j26-e
110-16205j26-e
110-16223j26-e
110-16224j26-e
110-16273j26-e
110-16472j26-e
110-16473j26-e
110-16474j26-e
110-16512j26-e
110-16513j26-e
115-h503a102-e
Resistor 100K 1/6W ±5% CF 26mm (RoHS)
Resistor 1M 1/6W ±5% CF 26mm (RoHS)
Resistor 1.2K 1/6W ±5% CF 26mm (RoHS)
Resistor 120K 1/6W ±5% CF 26mm (RoHS)
Resistor 15K 1/6W ±5% CF 26mm (RoHS)
Resistor 18K 1/6W ±5% CF 26mm (RoHS)
Resistor 2M 1/6W ±5% CF 26mm (RoHS)
Resistor 22K 1/6W ±5% CF 26mm (RoHS)
Resistor 220K 1/6W ±5% CF 26mm (RoHS)
Resistor 27K 1/6W ±5% CF 26mm (RoHS)
Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)
Resistor 47K 1/6W ±5% CF 26mm (RoHS)
Resistor 470K 1/6W ±5% CF 26mm (RoHS)
Resistor 5.1K 1/6W ±5% CF 26mm (RoHS)
Resistor 51K 1/6W ±5% CF 26mm (RoHS)
VAR Resistor RV16AE-20B2-15K-A54-104(A50K) LEVEL
R213,R214,R215,R254,R253
R212,R216,R217,R220,R221,R222,R225,R226,
17 R227,R228,
R229,R230,R232,R240,R260,R235,R200
3 R231,R263,R266,
1 R259,
1 R265,
1 R233,
1 R234,
1 R262,
1 R257,
3 R238,R255,R256,
1 R251,
2 R223,R237,
3 R258,R210,R209,
4 R219,R249,R250,R264,
1 R252,
1 R211,
1 R224,
1 VR201,
129-a154j633-e
Metalize CAP. 0.15U 63V ±5% MSC (RoHS)
2
130-2b221k503-e
Disc capacitor 220P 50V ±10% (RoHS)
9
130-3f104z503-e
Disc capacitor 0.1U 50V +80/-20% (RoHS)
8
130-ch220k503-e
132-103j503-e
132-104ja03-e
132-223ja03-e
132-473ja03-e
135-3105m50-e
Disc capacitor 22PF CH 50V±10% (RoHS)
Mylar capacitor 0.01uF 50V ±5% (RoHS)
Mylar capacitor 0.1UF 100V ±5% (RoHS)
Mylar capacitor 0.022uF 100V ±5% (RoHS)
Mylar capacitor 0.047uF 100V ±5% (RoHS)
Electroytic CAP. 1U 50V ±20% (RoHS)
1
2
1
1
2
1
135-3106m50-e
Electroytic CAP. 10uF 50V ±20% (RoHS)
8
135-3107m16-e
135-3226m50-e
135-3227m16-e
Electroytic CAP. 100uF 16V ±20% (RoHS)
Electroytic CAP. 22U 50V ±20% (RoHS)
Electroytic CAP. 220U 16V ±20% (RoHS)
1
2
1
192-027c1815gr-e
Transistor 2SC1815GR TOSHIBA(RoHS) NPN
3
197-631n4148-e
Diode 500mW 75V 1N4148 Panjit (RoHS)
9
199-65000513g-e
190-06m4558d-e
190-16tl074cn-e
195-10204hgw-e
zen Diode GDZJ5.1B 500mW 5.1V 2% 26mm 1N5231B(RoHS)
I.C. OPA 4558D (RoHS) DUAL OP-AMP
*I.C TL074CN ST (RoHS) QUAD OP-AMP
dual color LED 204HGW (RoHS)
1
1
2
1
RCA-108GV purple JK203 (RoHS)
RCA JACK RCA-209 gild (RoHS)
Wire connector & base 7PIN PITCH=2.5mm (RoHS)
SWITCH SLIDE 6PIN MS7210V (RoHS)
PCB bracket 11.75*8.5*12.5H (RoHS)
1
1
1
1
1
5
Capacitors
C221,C222,
C207,C208,C210,C211,C212,C214,C220,C230
C249,
C232,C242,C244,C245,C246,C252,C254,C256,
C229,
C223,C224,
C218,
C215,
C216,C217,
C228,
C206,C213,C219,C231,C241,C243,C251,C253,
C234,
C505,C506,
C118,
Semiconductors
Q206,Q207,Q208,
D201,D202,D207,D208,D211,D212,D214,D215
D216,
D213,
U203,
U201,U202,
D209,
Miscellaneous
174-0rca108gv-e
174-0rcb202vag-e
175-1c07v01-e
180-tms7210v-e
362-FE-00041-0LAE
JK201,
JK202,
M201,
SW202,
CS100 (CS6100 Subwoofer)
Part Number
Description
Qty Reference Designato
Main Amp PCB
Resistors
110-14103j26-e
110-14222j26-e
110-14432j26-e
110-14472j26-e
110-16102j26-e
Resistor 10K 1/4W ±5% CF 26mm (RoHS)
Resistor 2.2K 1/4W ±5% CF 26mm (RoHS)
Resistor 4.3K 1/4W ±5% CF 26mm (RoHS)
Resistor 4.7K 1/4W ±5% CF 26mm (RoHS)
Resistor 1K 1/6W ±5% CF 26mm (RoHS)
110-16103j26-e
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
110-16104j26-e
110-16153j26-e
110-16182j26-e
110-16203j26-e
110-16221j26-e
110-16222j26-e
110-16223j26-e
110-16333j26-e
110-16393j26-e
110-16473j26-e
110-16474j26-e
110-16562j26-e
110-16621j26-e
110-16751j26-e
110-16755j26-e
116-161002f26-e
116-161102f26-e
116-162200f26-e
116-162202f26-e
110-20332jk3-e
113-50s68j00-e
116-201001jk3x-e
116-304700jk2x-e
Resistor 100K 1/6W ±5% CF 26mm (RoHS)
Resistor 15K 1/6W ±5% CF 26mm (RoHS)
Resistor 1.8K 1/6W ±5% CF 26mm (RoHS)
Resistor 20K 1/6W ±5% CF 26mm (RoHS)
Resistor 220Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 2.2K 1/6W ±5% CF 26mm (RoHS)
Resistor 22K 1/6W ±5% CF 26mm (RoHS)
Resistor 33K 1/6W ±5% CF 26mm (RoHS)
Resistor 39K 1/6W ±5% CF 26mm (RoHS)
Resistor 47K 1/6W ±5% CF 26mm (RoHS)
Resistor 470K 1/6W ±5% CF 26mm (RoHS)
Resistor 5.6K 1/6W ±5% CF 26mm (RoHS)
Resistor 620Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 750Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 7.5M 1/6W ±5% CF 26mm (RoHS)
Metal film Resistor 10K 1/6W ±1% MF 26mm (RoHS)
Metal film Resistor 11.0K 1/6W ±1% MF 26mm (RoHS)
Metal film Resistor 220Ω 1/6W ±1% MF 26mm (RoHS)
Metal film Resistor 22.0K 1/6W ±1% MF 26mm (RoHS)
Resistor 3.3K 2W ±5% standing short feet 7.5m(RoHS)
cement Resistor 0.068Ω 5W ±5% horizontal (RoHS)
oxidation foil Resistor 1.00K 2W ±5% standing 7.5mm (RoHS)
oxidation foil Resistor 470Ω 3W ±5% clip feet 10mm (RoHS)
R503,R504,R510,
R511
R506,
R505,
R153,
R128,R130,R149,R150,R305,R306,R308,R311
10
R314,R319,
3 R122,R126,R307,
1 R107,
1 R145,
1 R309,
1 R144,
1 R102,
1 R316,
1 R310,
1 R151,
2 R106,R129,
2 R127,R312,
1 R152,
1 R160,
1 R315,
1 R313,
2 R301,R303,
1 R302,
1 R317,
1 R318,
1 R134,
1 R147,
1 R148,
2 R501,R502,
Disc capacitor 0.1U 50V +80/-20% (RoHS)
Disc capacitor 100P 50V SL ±10% (RoHS)
Mylar capacitor 0.01uF 50V ±5% (RoHS)
Mylar capacitor 0.01uf 100V ±5% (RoHS)
Mylar capacitor 0.1UF 100V ±5% (RoHS)
Mylar capacitor 0.027UF 100V ±5% (RoHS)
Electroytic CAP. 10uF 50V ±20% (RoHS)
Electroytic CAP. 100U 10V ±20% (RoHS)
Electroytic CAP. 100U 35V ±20% (RoHS)
Electroytic CAP. 2.2U 50V ±20% (RoHS)
Electroytic CAP. 22U 16V ±20% (RoHS)
Electroytic CAP. 22U 50V ±20% (RoHS)
Electroytic CAP. 220U 16V ±20% (RoHS)
Electroytic CAP. 47U 16V ±20% (RoHS)
Mylar capacitor 0.01U 400V +/-10% long feet (RoHS)
Electroytic CAP. 4700uF 63V ±20% (RoHS)
Disc capacitor 0.1U 50V +80/-20% (RoHS)
6
3
2
2
3
1
2
2
2
1
1
2
1
1
1
2
1
C107,C117,C122,C144,C320,C322
C302,C303,C306,
C305,C317,
C103,C104,
C123,C503,C504,
C143,
C319,C321,
C114,C115,
C507,C508,
C509,
C304,
C505,C506,
C118,
C318,
C500,
C501,C502,
C110,
I.C TL074CN ST (RoHS) QUAD OP-AMP
Transistor TIP31C SGS (RoHS) NPN
TransistorTIP32C SGS (RoHS) PNP
diode6A 800V KBU606G (RoHS) BRIDGE
Diode 1N4004 molding short feet (RoHS)
Transistor 2SC1815GR TOSHIBA(RoHS) NPN
1
1
1
1
2
5
U301,
Q501,
Q502,
D501,
D110,D504,
Q108,Q109,Q113,Q301,Q302,
3
1
1
1
1
Capacitors
130-3f104z503-e
130-sl101k503-e
132-103j503-e
132-103ja03-e
132-104ja03-e
132-273ja03-e
135-3106m50-e
135-3107m10-e
135-3107m35-e
135-3225m50-e
135-3226m16-e
135-3226m50-e
135-3227m16-e
135-3476m16-e
132-103kd00-e
135-4478m63-e
130-3f104z503-e
Semiconductors
190-16tl074cn-e
192-161tip31c-e
192-162tip32c-e
197-00kbu606g-e
197-141n4004-e
192-027c1815gr-e
CS100 (CS6100 Subwoofer)
Part Number
Description
Qty Reference Designato
Main Amp PCB
Transistor 2SC2235Y TOSHIBA (RoHS) NPN
Transistor 2SA1015GR TOSHIBA(RoHS) PNP
Transistor FSC 2N5551 (RoHS) NPN
Transistor FSC 2N5401 TO-92 (RoHS) PNP
Diode 500mW 75V 1N4148 Panjit (RoHS)
zener Diode GDZJ6.2B 500mW 6.2V 26mm 2% (RoHS)
zener Diode GDZJ16C 500mW 16V 26mm 2% (RoHS)
1
3
2
1
7
1
1
Q111,
Q101,Q107,Q112,
Q114,Q115,
Q503,
D102,D103,D104,D105,D143,D301,D302
D101,
D502,
175-1d02v01-e
175-1d03v01-e
362-FE-00013-0LAE
Wire connector & base 2PIN PITCH=3.96mm (RoHS)
1
1
2
M100,
M500,
Class D amp PCB
(Replacment of entire module is recommended, part# 050-B00012A-E).
192-027c2235y-e
192-028a1015gr-e
192-1572n5551-e
192-1582n5401-e
197-631n4148-e
199-65000623g-e
199-65001603g-e
Miscellaneous
Wire connector & base 3 PIN PITCH=3.96mm JST-VH no middle PIN
PCB bracket L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS)
Resistors
118-12061001j-e
118-12061002j-e
118-120610r0j-e
SMD Resistor 1.00K 1206 5% (RoHS)
SMD Resistor 10.0K 1206 5% (RoHS)
SMD Resistor 10.0Ω 1206 5% (RoHS)
118-12061201j-e
SMD Resistor 1.20K 1206 5% (RoHS)
118-12062002j-e
118-12062201j-e
118-12062701j-e
118-12063000j-e
118-12063301j-e
118-12063902j-e
118-12064700j-e
118-12064701j-e
118-12064702j-e
118-12064704j-e
118-120647r0j-e
SMD Resistor 20.0K 1206 5% (RoHS)
SMD Resistor 2.20K 1206 5% (RoHS)
SMD Resistor 2.70K 1206 5% (RoHS)
SMD Resistor 300.0Ω 1206 5% (RoHS)
SMD Resistor 3.30K 1206 5% (RoHS)
SMD Resistor 39.0K 1206 5% (RoHS)
SMD Resistor 470Ω 1206 5% (RoHS)
SMD Resistor 4.70K 1206 5% (RoHS)
SMD Resistor 47.0K 1206 5% (RoHS)
SMD Resistor 4.70M 1206 5% (RoHS)
SMD Resistor 47.0Ω 1206 5% (RoHS)
R2,R11,R29,R30,R7,R9,R25,
R7.R9.R25
R22,R23,
R31,R32,R33,R34,R35,R36,R37,R38,R39,R40
16
R41, R42,R43,R44,R45,R46,
1 R26,
3 R6,R13,R16,
1 R10,
1 R24,
4 R14,R15,R27,R28,
1 R3,
1 R8,
3 R1,R5,R12,
1 R17,
1 R4,
2 R20,R21,
SMD capacitor 100pF 50V 10% 1206 NP0 (RoHS)
SMD capacitor 22pF 50V 10% 1206 SMT NPO (RoHS)
SMD capacitor 560pF 50V 10% 1206 NPO (RoHS)
SMD capacitor 1206 Y5V 0.1uF 50V ±20% (RoHS)
SMD capacitor 0.022uF 50V 10% 1206 X7R (RoHS)
SMD capacitor 0.1uF 100V 10% 1210 X7R (RoHS)
SMD capacitor 0.1uF 250V 10% 1210 X7R (RoHS)
non-polarity Electroytic CAP. 10UF 100V 20% 105℃ (RoHS)
1
1
1
8
1
1
5
2
C4,
C5,
C6,
C2,C3,C7,C8,C9,C10,C11,C15,
C13,
C12,
C1,C18,C19,C20,C14,
C16,C17,
SMD I.C. TL072CDT SGS THOMSON DUAL OP-AMP
SMD Transistor 2SC2412K-T146Q/R ROHM (RoHS)
SMD Transistor 2SC3906K-T146R ROHM (RoHS)
SMD Transistor 2SA1037K-T146Q/R ROHM (RoHS)
SMD Transistor 2SA1514K-T146R ROHM (RoHS)
SMD Diode RLS4148-TE11 ROHM (RoHS)
SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 (RoHS)
SMD ZENER 12V 5% PHILIPS BZX84-C12 (RoHS)
SMD ZENER 15V 5% PHILIPS BZX84-C15 (RoHS)
FET IRF9640 IR P-CH TO220 (RoHS)
Transistor IRF640N INTERNATIONAL (RoHS)
1
3
2
2
2
6
2
2
2
1
1
IC1,
Q1,Q4,Q5,
Q2,Q8,
Q7,Q9,
Q3,Q6,
D1,D2,D3,D4,D5,D6,
Z1,Z2,
Z5,Z6,
Z3,Z4,
Q10,
Q11,
7
3
2
Capacitors
141-c0101k50-e
141-c0220k50-e
141-c0561k50-e
141-c5104m50-e
141-c7223k50-e
141-d7104ka0-e
141-d7104kb5-e
128-e106ma01k-e
Semiconductors
190-16tl072dts-e
192-09124126qs-e
192-09139066rs-e
192-09210376qs-e
192-09215146rs-e
197-03rls4148s-e
199-15000563s-e
199-1500120s-e
199-15001503s-e
192-232irf9640-e
192-233f640n-e
CS100 (CS6100 Subwoofer)
Part Number
Class D amp PCB
Description
Qty Reference Designato
(Replacment of entire module is recommended, part# 050-B00012A-E).
Miscellaneous
122-14121m4191-e
122-14350j4180-e
175-9f40hr2-e
Ferrite core 日 font LS-A6206-ST EFD-30 (RoHS)
inductor 35uH Ferrite Core 25 Milliohm (RoHS)
Wire connector & base 40PIN PITCH=2.54mm HR2*40
1
1
L1,
L2,
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
2
1
1
1
2
4
4
3
2
2
2
1
TH1,
FB1,FB2,
W201,
RL1,
T501,
MISCELLANEOUS/MECHANICAL
109-1ttc802j0-e
120-1000003-e
162-50129001-e
171-urwh124d-e
150-r4055900-e
152-u602015-e
154-k31505t0-e
155-63032i-e
156-h200040-e
156-h200050-e
162-10151001-e
162-a040d001-e
176-wjce1-e
180-pbr12c11s-e
193-201815t2-e
302-AL-05092-0LAE
306-ABS-00004-0BAE
311-ABS-00028-0BAE
317-000-00037-0LAE
323-AL-00056-0LAE
333-EVA-00096-0BAE
333-EVA-00097-0BAE
333-EVA-00132-0BAE
333-EVA-00133-0BAE
333-EVA-00188-0BAE
333-EVA-00219-0BAE
333-EVA-00220-0BAE
335-NYL-05015-0BAE
350-EM04012D024-E
351-AM03008A078-E
351-AM03008A079-E
352-AM03008D040-E
352-AM03008D041-E
352-AM03010D065-E
352-HM03012D086-E
thermistor Resistor TTC-802(JS) NTC long feet (RoHS)
inductor 10W AI YT-C3104-005 1CRHW 354708LTB (RoHS)
CABLE ASS'Y row wire 120mm AWG28 WHT (RoHS)
relay RWH-SH-124D (1600 ohm) (RoHS)
Power transformer I/P:120V/60Hz TT0900008720 (RoHS)
Line cord tie-in with polarity SVT FT-2 6FT both insulation
Fuse 3.15A 250V 30mm UL/CSA/PSE (RoHS)
Fuse holder HTB-32I 30mm UL/CSA (RoHS)
pyrocondensation sleeve 20ψ*40mm (RoHS)
pyrocondensation sleeve 20Φ 50mm (RoHS)
WIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS)
speaker wire #1015 400mm 991110-00 (HG150 use ) (RoHS)
Wire connector pin CE-1 (RoHS)
power switch PUSH BR12C11S (RoHS)
ceramic insulator (RoHS)
Rear board 270*215*2.5T al, black printing CSC100 120V
Rear housing REAR CABINET 268*213*102 A.B.S UL (RoHS)
Plastic knob 46077-W soft material P.V.C. (RoHS) LEVEL
earth end M3 solder t=0.3 (RoHS)
Heat sink 83.5*50.5*27.5H degrease
EVA gasket wide side 213*15*2.0mm (RoHS)
EVA gasket wide side 213*15*1.0t (RoHS)
EVA gasket Long side 238*15*2.0mm (RoHS)
EVA gasket Long side 238*15*1.0t (RoHS)
EVA gasket 170x5x1t back with glue (RoHS)
EVA gasket wide side 150*15*1t UL (RoHS)
EVA gasket Long side 225*15*1t UL (RoHS)
Line cord fixed button SB4F-2 black (RoHS)
4¢*12 Wood screw electric black (RoHS)
M3*8 Machin screw plating nickel (RoHS)
M3*8 Machin screw electric black (RoHS)
¢3*8 B ping screw electric black (RoHS)
¢3*8 B ping screw plating nickel (RoHS)
¢3*10 P ping screw electric black (RoHS)
¢3*12 B ping screw electric black (RoHS)
F501,
for F501,
SW501,
CS100 (CS6100 Subwoofer)
15
CS100 (CS6100 Subwoofer)
16
CS100 (CS6100 Subwoofer)
17
CS100 (CS6100 Subwoofer)
18
CS100 (CS6100 Subwoofer)
19
CS100 (CS6100 Subwoofer)
20
CS100 (CS6100 Subwoofer)
21
CS100 (CS6100 Subwoofer)
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement