SUB10 SERVICE MANUAL Venue
Venue™ Series
SUB10
Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products
250 Crossways Park Dr.
Woodbury, New York 11797
Rev2
8/2006
SUB10
Venture Series
- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
PACKAGING…………………………….………………………......2
DETAILED SPECIFICATIONS
……..…………….……………..3
CONNECTIONS..……………………………………………………5
OPERATION ………….……………………………..…………….7
TEST SET-UP AND PROCEDURE……..……….…….………….8
EXPLODED VIEW/PARTS LIST…………………………………..9
BLOCK DIAGRAM..……………………………………….…........10
120V ELECTRICAL PARTS LIST ……………………………….11
PCB DRAWINGS………………..………………………………...15
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS…………..21
120V SCHEMATICS.……….…………….…………..…. ………22
BASIC SPECIFICATIONS
SUB10 Subwoofer
Frequency response:
27Hz – 150Hz
Amplifier Power output:
150W Continuous RMS power
Amplifier Peak Dynamic Power†:
250W
Crossover Frequencies
50Hz – 150Hz, 24dB/octave, continuously variable
Woofer:
10" (250mm) PolyPlas™ cone
Dimensions (including grille):
17-3/4" x 12-1/4" x 15-3/4" (451mmx311mmx400mm)
Weight:
32.1 lb/14.6kg
† The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the
output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles
on, 17 cycles off.
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
SUB10
Venture Series
2
SUB10
Venture Series
JBL Venue Sub10 150W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120vac/60Hz
EU 230vac/50-60Hz
Asia 100vac/50Hz
Yes/No
Yes
Yes
Yes
Hi/Lo Line
108-132
207-264
90-110
Unit
Vrms
Vrms
Vrms
Parameter
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
[email protected] Rated Power
THD @ 1 Watt
DC Offset
Specification
Unit
QA Test Limits
D
4
150
0.08
0.1
10
D
Ohms
Watts
%
%
mV-DC
n/a
n/a
145
1.5
0.5
20
Nominal
1 input driven
22K filter
22K filter
@ Speaker Output
>100
N/A
15
50Hz, 4 Ohms load
Damping factor
Notes
Normal Operation
Normal operation, MOMS required
Normal Operation
Conditions
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
50
13
8
Hz
mVrms
mVrms
50
±2dB
±2dB
Nominal Freq.
To 1 W
To 1 W
Speaker/Hi Level Input
110
mVrms
±2dB
To 1 W
100
90
60
dBA
dBr
dBr
85
80
55
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
Residual Noise Floor
1
mVrms
2
rel. to rated power
rel. to rated power
rel. to 1W Output
Volume @max, using RMS reading
DMM/VOM (or A/P)
Residual Noise Floor
1
mVrms(max)
2
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
K ohms
K ohms
n/a
n/a
Input Impedance
Line input L&R , LFE
Speaker/Hi Level Input
>15
4.7
Filters
Left & Right inputs LP
Slope & Q
LFE Low Pass fixed
Slope & Q
Subsonic filter (HPF)
Slope & Q
Hz
-4th dB/Octave
Hz
-2nd dB/Octave
Hz
-5th dB/Octave
±2dB
n/a
±2dB
n/a
±2dB
n/a
Notes
Measured at amplifier board speaker output
terminals @ 135 Watts
1 input driven, AP Zo=600 Ohms
1 input driven, AP Zo=600 Ohms
LFE input driven only, AP Zo=600 Ohms
(Approx -20 dB below Line In)...1 input
driven
A-Weighting filter
22K filter
22K filter
Nominal
Nominal
2nd order fix and 2nd order variable
Limiter (yes/no)
YES
--
n/a
Features
LFE Input
Phase Switch (yes/no)
Volume pot Taper (lin/log)
ATO switch (AUTO/ON)
YES
YES
LOG
YES
---
functional
functional
functional
functional
BW Limited to 500 Hz
Input Configuration
Line In (L,R)
Line level in LFE
Spkr/Hi Level In (L,R)
Spkr Out: Level out (L,R)
L ,R
LFE
L,R
L,R
--
functional
functional
functional
functional
RCA inputs: L and R
50
Hz
2
mV
functional
25
mV
functional
5
ms
functional
[email protected] into Line Input w/ 1 ch.
driven
Amp connected and AC on, then input
signal applied
15
minutes
functional
T before muting, after signal is removed Auto turn of time (T) must be 10 > T <15
--
L & R inputs, binding post connectors
Only applies to 230V model
Signal Sensing (ATO)
ATO test Frequency
ATO Line Level
ATO Speaker level input
ATO Turn-on time
Auto Mute/ Turn-OFF Time
[email protected] into Line Input w/ 1 ch.
driven
3
SUB10
Parameter
Power on Delay time
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
Venture Series
Specification
Unit
QA Test Limits
3
sec.
functional
5
50
50
mV-peak
mV-peak
mV-peak
10
100
100
Conditions
Notes
AC Power Applied
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
140 Watts @ 4 Ohms nominal line voltage
Efficiency
Stand-by Input Power
Power [email protected] power
Protection
Short Circuit Protection
Thermal Protection
DC Offset Protection
Line Fuse Rating
14
230
Watts
Watts
16
240
@ nom. line voltage
@ nom. line voltage
YES
--
functional
Direct short at output
65 deg. C
YES
---
functional
functional
@1/8 max unclipped Power
DC present at Speaker Out leads
US Version
3.15
Amps
EU Version
1.6
Amps
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
Type-T or Slo Blo, T3.15A, 250V
External fuse with UL/SEMKO rated holder
Type-T, Low breaking capacity, T1.6AL,
250V
External fuse with UL/SEMKO rated holder
4
SUB10
Venture Series
SYSTEM CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/processor with a low-frequencyeffects (LFE) or subwoofer output:
If your receiver/processor does not have subwoofer outputs for the left and
right channels or an LFE output, connect speaker wire from your receiver/
amplifier to your speakers and subwoofer using two sets of speaker wire:
SUBWOOFER OR
LFE OUTPUT
RECEIVER/AMPLIFIER
Front Speaker Output
IN
ANDBY
L
R
0
0
IN
L
R
If your receiver/processor does not contain a Dolby Digital or DTS processor
but has subwoofer outputs:
NOTE: If your receiver/processor has only one sub out, you may use either the
L or R input.
RECEIVER/PROCESSOR
L
R
IN
L
R
L
0
This figure shows how to connect bare wires to the speaker-level terminals.
5
SUB10
Venture Series
SPEAKER LEVEL
IN
LINE LEVEL IN
1
0
L
R
LFE
4
3
GREEN: ON
RED: STAND-BY
SUBWOOFER
LEVEL
CROSSOVER
L
2
PHASE
AUTO ON
R
MIN
5
MAX
"WAR NING : FOR CONTINUED
PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH
SAME TYPE T 3.15A L/250V FUSE"
180
6
7
0
50
Hz
150
T3.15A L/250V
"AVE R TIS S E ME NT: UTILISEZ UN
FUSIBLE DE RECHANGE DE MEME
TYPE T 3.15A L/250V"
™
®
0
0
SUB10
POWER
®
8
R
NRTL/C
CSA 22-2 No.1
UL 1492
C A UT IO N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
¡ Speaker-Level Inputs
§ On/Off Auto Switch
™ LFE Input
¶ Phase Switch
£ Line Inputs
• Crossover Adjustment
¢ Subwoofer-Level Control
ª Power Switch
∞ Power Indicator LED
6
AC 120V~60Hz
250 Watts
SUB10
Venture Series
OPERATION
Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the
back of the receiver.
Initially set the Subwoofer-Level Control ¢ to the “min” position.
The enclosure may be cleaned using a soft cloth to remove fingerprints or to
wipe off dust.
The grille may be gently vacuumed. Stains may be removed with an aerosol
cleaner, following its instructions. Do not use any solvents on the grille.
Turn on your sub by pressing the Power Switch ª on the rear panel.
Turn on your entire audio system and start a CD or movie soundtrack at a
moderate level.
Auto On/Standby
With the Power Switch ª in the “on” position, the Power Indicator LED ∞
will remain backlit in red or green to indicate the On/Standby mode of the
subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
When the Auto Switch § is in the “auto” position, the subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly
when a signal is detected. During periods of normal use, the Power Switch ª
may be left on. You may turn off the Power Switch ª for extended periods of
non-operation, e.g., when you are away on vacation. If the Auto Switch § is in
the “on” position, the subwoofer will remain on.
Adjust Gain
Turn your Subwoofer-Level Control ¢ up to the halfway position. If no sound
emanates from the subwoofer, check the AC-line cord and input cables. Are the
connectors on the cables making proper contact? Is the AC plug connected to
a “live” receptacle? Has the Power Switch ª been pressed to the “on” position? Once you have confirmed that the subwoofer is active, proceed by playing a CD, record or cassette. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a comfortable
level. Adjust the Subwoofer-Level Control ¢ until you obtain a pleasing blend
of bass. Bass response should not overpower the room but rather be adjusted
so there is a harmonious blend across the entire musical range. Many users
have a tendency to set the subwoofer volume too loud, adhering to the belief
that a subwoofer is there to produce lots of bass. This is not entirely true. A
subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An experienced listener will
set the volume of the subwoofer so its impact on bass response is always
there but never obtrusive.
Phase Control
The Phase Switch ¶ determines whether the subwoofer speaker’s pistonlike
action moves in and out with the main speakers, 0˚, or opposite the main
speakers, 180˚. Proper phase adjustment depends on several variables such
as room size, subwoofer placement and listener position. Adjust the Phase
Switch to ¶ maximize bass output at the listening position.
Crossover Adjustment
The Crossover Adjustment Control • determines the highest frequency at
which the subwoofer reproduces sounds. If your main speakers can comfortably
reproduce some low-frequency sounds, set this control to a lower frequency
setting, between 50Hz and 100Hz. This will concentrate the subwoofer’s
efforts on the ultradeep bass sounds required by today’s films and music.
If you are using smaller bookshelf speakers that do not extend to the lower
bass frequencies, set the Crossover Adjustment Control • to a higher setting,
between 120Hz and 150Hz.
NOTE: This control will have no effect if the LFE/Input ™ is used. If you have
a Dolby Digital or DTS processor/receiver, the low-pass frequency is set by the
processor/receiver. Consult your owner’s manual to learn how to view or
change this setting.
6
7
SUB10
Venture Series
SUB10 Test Set Up and Procedure
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect line level (RCA) cables to the Subwoofer Line Level Input jacks L/R on
the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the
single LFE input.
2) Turn the CROSSOVER control to maximum (150).
3) Turn the LEVEL control on the UUT to completely counterclockwise (MIN).
4) Turn on generator; adjust to 100mV, 50 Hz.
5) Plug in UUT; turn the power switch ON. LED should switch from Red to Green.
6) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt
from port tube opening on the bottom.
7) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
8) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be
connected to an integrated amplifier fed by the signal generator.
9) Turn on generator and adjust so that speaker level input at the amplifier is 2.0V, 50 Hz. Turn LEVEL control
full clockwise (MAX).
10) Green LED should light; immediate and vigorous bass response should be heard and felt from the port
tube opening.
Sweep Function
1) Follow steps 8-10 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips.
2) Check DC resistance of woofer; it should be 5.7 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
SUB10
Venture Series
9
SUB10
Venture Series
10
SUB10
Venture Series
SUB10 120V Electrical parts list
Part number
Description
Qty Reference Designator
Resistor4.7K 1/2W ±5% CF 52mm (RoHS)
Resistor 1K 1/6W ±5% CF 26mm (RoHS)
R201,R202
R213,R214,R215,R254
R209,R212,R216,R217,R220,R221,R222,R228,
15 R218,R230,R232,R240,R248,R260,R235
4 R231,R263,R266,R251
1 R259
1 R265
1 R253
1 R252
R261
1
1 R257
3 R247,R255,R256
1 R249
3 R208,R207,R258
3 R219,R250,R264
2 R210,R211
4 R203,R204,R205,R206
3 R10,R11,R9
2 R225,R7
1 R3
2 R226,R227
R238,R237
2
R6
1
2 R223,R224
1 R233
1 R234
1 VR202,
1 VR201
PREAMP PCB
Resistors
110-12472j52-e
110-16102j26-e
110-16103j26-e
110-16104j26-e
110-16105j26-e
110-16122j26-e
110-16151j26-e
110-16154j26-e
110-16183j26-e
110-16205j26-e
110-16223j26-e
110-16333j26-e
110-16472j26-e
110-16473j26-e
110-16512j26-e
110-16913j26-e
116-161002f26-e
116-161132f26-e
116-161301f26-e
116-161372f26-e
116-161542f26-e
116-162433f26-e
116-165601f26-e
116-166042f26-e
116-169091f26-e
115-h203b201-e
115-h503a101-e
Resistor10K 1/6W ±5% CF 26mm
2
4
(RoHS)
Resistor100K 1/6W ±5% CF 26mm (RoHS)
Resistor1M 1/6W ±5% CF 26mm (RoHS)
Resistor 1.2K 1/6W ±5% CF 26mm (RoHS)
Resistor 150Ω 1/6W ±5% CF 26mm (RoHS)
Resistor150K 1/6W ±5% CF 26mm (RoHS)
Resistor18K 1/6W ±5% CF 26mm (RoHS)
Resistor 2M 1/6W ±5% CF 26mm (RoHS)
Resistor22K 1/6W ±5% CF 26mm (RoHS)
Resistor 33K 1/6W ±5% CF 26mm(RoHS)
Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)
Resistor47K 1/6W ±5% CF 26mm (RoHS)
Resistor 5.1K 1/6W ±5% CF 26mm (RoHS)
Resistor 91K 1/6W ±5% CF 26mm (RoHS)
Metal Film Resistor 10K 1/6W ±1% MF 26mm (RoHS)
Metal Film Resistor11.3K 1/6W ±1% MF
26mm (RoHS)
Metal Film Resistor1.30K 1/6W MF 26mm (RoHS)
Metal Film Resistor 13.7K 1/6W MF 26mm (RoHS)
Metal Film Resistor 1/6W 15.4K 1% 26mm (RoHS)
Metal Film Resistor 243K 1/6W 1% MF 26mm (RoHS)
Metal Film Resistor 5.60K 1/6W ±1% MF26mm (RoHS)
Metal Film Resistor 60.4K 1/6W±1% MF
Metal Film Resistor 9.09K 1/6W±1% MF
variable Resistor 20KB/2 CROSSOVER
variable Resistor D16 50K/1 A (RoHS) LEVEL
Capacitors
129-a153j633-e
129-a224j633-e
129-a334j633-e
130-2b221k503-e
130-3f104z503-e
130-sl101k503-e
132-103j503-e
132-104ja03-e
132-473ja03-e
135-3105m50-e
135-3106m50-e
135-3107m16-e
135-3226m50-e
135-3227m16-e
129-a334j633-e
C224
C221,C222,C218
C1,C3
C200,C204,C205,C207,C213,C210,C211,C212,
12 C214,C220,C230,C249,
9 C232,C242,C244,C245, C246,C252,C254,C255,C256
C6
1
1 C223
1 C216
2 C215,C217
1 C228
10 C201,C202,C206,C208, C231,C241,C243,C251,C253,C219
1 C234
2 C225,C7
1 C233,
1 C2,
1
3
2
Metallize Capacitor 0.015U 63V MSC
Metallize Capacitor 0.22uF 63V ±5% MSC
Metallize Capacitor 0.33uF 63V ±5% MSC
Disc Capacitor 220P 50V ±10%
Disc Capacitor 0.1U 50V +80/-20%
Disc Capacitor 100P 50V SL ±10%
mylar Capacitor 0.01uF 50V ±5%
mylar Capacitor 0.1UF 100V ±5%
mylar Capacitor 0.047uF 100V ±5%
electrolytic 1U 50V ±20%
electrolytic10uF 50V ±20%
electrolytic 100uF 16V ±20%
electrolytic 22U 50V ±20%
electrolytic 220U 16V ±20%
metalize cap 0.33uF 63V ±5% MSC
Semiconductors
Q201,Q207,Q208,
D201,D202,D203,D204, D205,D206,D207,D208,
13 D211,D212,D214,D215,D216
D213,
1
U1,U203,
2
U201,U202,
2
Q206,
1
192-027c1815gr-e Transistor 2SC1815GR TOSHIBA(RoHS) NPN
197-031n4148-e
199-15000335-e
190-06m4558d-e
190-16tl074cn-e
192-027c1815gr-e
3
diode 100mA 75V SIGNAL 1N4148
zener diode 3.3V 1/2W 52mm TA
I.C. OPA 4558D (RoHS) DUAL OP-AMP
*I.C TL074CN ST (RoHS) QUAD OP-AMP
Transistor 2SC1815GR TOSHIBA(RoHS) NPN
11
SUB10
Part number
Venture Series
Description
Qty Reference Designator
PREAMP PCB
195-10204hgw-e
double color LED 204HGW 3¢(RoHS)
1
D209,
Miscellaneous
162-50062001-e
174-0rca326p-e
174-2wp810a-e
175-1c07v01-e
180-tsv6201-e
2PIN 60mm red/black
JACK RCA-326 (RoHS)
SPK JACK 8P red up black down with cap
wire connector &base7PIN PITCH=2.5mm (RoHS)
switch 6PIN DC30V 0.3V AUTO-ON, PHASE
1
1
1
1
2
for D209,
JK201,
JK203,
P201,
SW1,SW201
1
1
1
2
3
1
1
R134
R147
R148
R501,R502
R503,R504,R510,
R511,
R506,
R505,
R153,
MAIN PCB
Resistors
110-20332jk3-e
113-50s68j00-e
116-201001jk3x-e
116-304700jk2x-e
110-14103j26-e
110-14222j26-e
110-14432j26-e
110-14472j26-e
110-16102j26-e
Resistor 3.3K 2W ±5% portrait short foot7.5m(RoHS)
Resistor 0.068Ω 5W ±5% landscape short foot(RoHS)
Metal Film Resistor 1.00K 2W ±5% (RoHS)
Metal Film Resistor 470Ω 3W ±5% 10mm (RoHS)
Resistor10K 1/4W ±5% CF 26mm
Resistor 2.2K 1/4W ±5% CF 26mm TAP (RoHS)
Resistor4.3K 1/4W ±5% CF 26mm
Resistor 4.7K 1/4W ±5% CF 26mm
Resistor 1K 1/6W ±5% CF 26mm
110-16103j26-e
110-16104j26-e
110-16153j26-e
110-16182j26-e
110-16203j26-e
110-16221j26-e
110-16222j26-e
110-16223j26-e
110-16333j26-e
110-16393j26-e
110-16434j26-e
110-16473j26-e
110-16474j26-e
110-16562j26-e
110-16621j26-e
110-16751j26-e
110-16755j26-e
116-161002f26-e
116-161202f26-e
116-162200f26-e
116-162202f26-e
Resistor10K 1/6W ±5% CF 26mm
Resistor 100K 1/6W ±5% CF 26mm
Resistor15K 1/6W ±5% CF 26mm
Resistor 1.8K 1/6W ±5% CF 26mm
Resistor 20K 1/6W ±5% CF 26mm
Resistor220Ω 1/6W ±5% CF 26mm
Resistor 2.2K 1/6W ±5% CF 26mm
Resistor 22K 1/6W ±5% CF 26mm
Resistor33K 1/6W ±5% CF 26mm
Resistor 39K 1/6W ±5% CF 26mm
Resistor 430K 1/6W ±5% CF 26mm
Resistor 47K 1/6W ±5% CF 26mm
Resistor 470K 1/6W ±5% CF 26mm
Resistor 5.6K 1/6W ±5% CF 26mm
Resistor 620Ω 1/6W ±5% CF 26mm
Resistor 750Ω 1/6W ±5% CF 26mm
Resistor 7.5M 1/6W ±5% CF 26mm
metal film Resistor10K 1/6W ±1% MF 26mm
metal film Resistor 12.0K 1/6W ±1% MF
metal film Resistor 220Ω 1/6W ±1% MF
metal film Resistor 22.0K 1/6W ±1% MF
10
3
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
R128,R130,R149,R150,R305,R306,R308,R311,R314,R319,
R122,R126,R307,
R107,
R145,
R309,
R144,
R102,
R316,
R310,
R151,
R312,
R106,R129,
R127,
R152,
R160,
R315,
R313,
R301,R303,
R302,
R317,
R318,
large aluminum ec 4700uF 80V ±20% 85℃ (RoHS)
Mylar Capacitor 0.01u 100V (RoHS)
mylar Capacitor 0.01U 400V +/-10% long foot (RoHS)
base capacity 0.1U 50V +80/-20%
base Capacitor 100P 50V SL ±10%
mylar Capacitor0.01uF 50V ±5%
mylar Capacitor 0.1UF 100V ±5%
mylar Capacitor0.027UF 100V ±5%
electrolytic Capacitor 10uF 50V ±20%
electrolytic cap 100U 10V ±20%
electrolytic cap100U 35V ±20%
electrolytic cap 2.2U 50V ±20%
electrolytic cap 22U 16V ±20%
2
2
1
6
3
2
3
1
2
2
2
1
1
C501,C502
C103,C104
C500
C107,C117,C122,C144, C320,C322
C302,C303,C306,
C305,C317,
C123,C503,C504,
C143,
C319,C321,
C114,C115,
C507,C508,
C509,
C304,
1
1
Capacitors
138-5478m80-e
132-a103ja03-e
132-103kd00-e
130-3f104z503-e
130-sl101k503-e
132-103j503-e
132-104ja03-e
132-273ja03-e
135-3106m50-e
135-3107m10-e
135-3107m35-e
135-3225m50-e
135-3226m16-e
12
SUB10
Part number
Venture Series
Description
Qty Reference Designator
MAIN PCB
135-3226m50-e
135-3227m16-e
135-3476m16-e
electrolytic cap 22U 50V ±20%
electrolytic cap 220U 16V ±20%
electrolytic cap47U 16V ±20%
2
1
1
C505,C506,
C118,
C318,
*I.C TL074CN ST (RoHS) DUAL OP-AMP
Transistor TIP31C SGS (RoHS) NPN
TransistorTIP32C SGS (RoHS) PNP
diode6A 800V KBU606G (RoHS) BRIDGE
diode1N4004 (RoHS)
Transistor 2SC1815GR TOSHIBA(RoHS) NPN
Transistor2SC2235Y TOSHIBA (RoHS) NPN
Transistor 2SA1015GR TOSHIBA(RoHS) PNP
TransistorFSC 2N5551 (RoHS) NPN
TransistorFSC 2N5401 TO-92 (RoHS) PNP
diode100mA 75V SIGNAL 1N4148
zener diode HZ6C2 RENESAS (6.2v)
zener diode HZ16-2 RENESAS (16v)
1
1
1
2
5
1
3
2
1
4
1
1
U301
Q501
Q502
D501
D110,D504
Q108,Q109,Q113,Q301, Q302,
Q111,
Q101,Q107,Q112,
Q114,Q115,
Q503,
D102,D103,D104,D105,
D101,
D502,
inductor10W AI YT-C3104-005 1CRHW354708LTB (RoHS)
Thermister TTC-802(JS) NTC long foot(RoHS)
2
1
1
1
1
1
FB1,FB2
TH1
W201
RL1
M100
M500
Semiconductors
190-16tl074cn-e
192-161tip31c-e
192-161tip32c-e
197-00kbu606g-e
197-141n4004-e
192-027c1815gr-e
192-027c2235y-e
192-028a1015gr-e
192-1572n5551-e
192-1582n5401-e
197-031n4148-e
199-15000625-e
199-15001605-e
1
Miscellaneous
120-1000003-e
109-1ttc802j0-e
162-50129001-e
171-urwh124d-e
175-1d02v01-e
175-1d03v01-e
CABLE ASS'Y wire 120mm AWG28 WHT (RoHS)
Relay RWH-SH-124D (1600 ohm) (RoHS)
Wire connector&base 2PIN PITCH=3.96mm (RoHS)
Wire connector&base 3 PIN PITCH=3.96mm (RoHS)
CLASS D ASS'Y PCB (Replacment of entire module is recommended, part# 051-B00012A-E).
Resistors
118-120610r0j-e
118-12061001j-e
118-12061002j-e
SMDresistor 10.0Ω 1206 5% (RoHS)
SMDresistor 1.00K 1206 5% (RoHS)
SMDresistor 10.0K 1206 5% (RoHS)
2
4
3
118-12061201j-e
118-12062002j-e
118-12062201j-e
118-12062701j-e
118-12063000j-e
118-12063301j-e
118-12063902j-e
118-120647r0j-e
118-12064700j-e
118-12064701j-e
118-12064702j-e
118-12064704j-e
SMDresistor 1.20K 1206 5% (RoHS)
SMDresistor 20.0K 1206 5% (RoHS)
SMDresistor 2.20K 1206 5% (RoHS)
SMDresistor 2.70K 1206 5% (RoHS)
SMDresistor 300.0Ω 1206 5% (RoHS)
SMDresistor 3.30K 1206 5% (RoHS)
SMDresistor 39.0K 1206 5% (RoHS)
SMDresistor 47.0Ω 1206 5% (RoHS)
SMDresistor 470Ω 1206 5% (RoHS)
SMDresistor 4.70K 1206 5% (RoHS)
SMDresistor 47.0K 1206 5% (RoHS)
SMDresistor 4.70M 1206 5% (RoHS)
R22,R23
R2,R11,R29,R30
R7,R9,R25
R31,R32,R33,R34,R35,R36,R37,R38
16 R39,R40,R41,R42,R43,R44,R45,R46
1 R26
3 R6,R13,R16
1 R10
1 R24
4 R14,R15,R27,R28,
1 R3
2 R20,R21
1 R8,
3 R1,R5,R12,
1 R17
1 R4,
crossver cap 10UF 100V 20% 105℃ long foot (RoHS)
2
Capacitors
128-e106ma01k-e
141-c0220k50-e
141-c0561k50-e
141-c5104m50-e
141-c7223k50-e
141-c0101k50-e
141-d7104ka0-e
141-d7104kb5-e
SMD Capacitor 22pF 50V 10% 1206
SMT NPO (RoHS)
SMD Capacitor 560pF 50V 10%
SMD Capacitor 1206 Y5V 0.1uF 50V ±20% (RoHS)
SMD Capacitor 0.022uF 50V 10%1206 X7R (RoHS)
SMD Capacitor 100pF 50V 10% 1206 NP0 (RoHS)
SMD Capacitor 0.1uF 100V 10% 1210 X7R (RoHS)
SMD Capacitor 0.1uF 250V 10% 1210 X7R (RoHS)
13
1
1
8
1
1
2
4
C16,C17
C5,
C6,
C2,C3,C7,C8,C9,C10,C11,C15,
C13,
C4,
C12,C14
C1,C18,C19,C20,
SUB10
Part number
Venture Series
Description
Qty Reference Designator
CLASS D ASS'Y PCB (Replacment of entire module is recommended, part# 051-B00012A-E).
Semiconductors
190-16tl072dts-e
192-09124126qs-e
192-09139066rs-e
192-09210376qs-e
192-09215146rs-e
197-03rls4148s-e
192-232irf9640-e
192-233f640n-e
199-15000563s-e
199-1500120s-e
199-15001503s-e
SMD I.C. TL072CDT SGS THOMSON DUAL OP-AMP
1
3
2
2
2
6
SMD Transistor 2SC2412K-T146Q/R
SMD Transistor 2SC3906K-T146R ROHM
SMD Transistor 2SA1037K-T146Q/R
SMD Transistor2SA1514K-T146R ROHM
SMD Transistor RLS4148-TE11 ROHM
FET IRF9640 IR P-CH TO220(RoHS)
Transistor IRF640N INTERNATIONA(RoHS)
1
1
SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 (RoHS)
SMD ZENER 12V 5% PHILIPS BZX84-C12 (RoHS)
SMD ZENER 15V 5% PHILIPS BZX84-C15 (RoHS)
2
2
2
IC1,
Q1,Q4,Q5,
Q2,Q8,
Q7,Q9
Q3,Q6,
D1,D2,D3,D4,D5,D6,
Q10
Q11
Z1,Z2,
Z5,Z6,
Z3,Z4
Miscellaneous
1 L1
1 L2
0.2
122-14121m4191-e Ferrite core LS-A6206-ST EFD-30 (RoHS)
122-14350j4180-e chock coil35uH Ferrite Core 25 Milliohm (RoHS)
175-9f40hr2-e
wire connector & base 40PIN (RoHS)
MISCELLANEOUS/MECHANICAL
350-FM04012D106-E ψ4*12 wood screw(RoHS)
352-AM03010D066-E ¢3*10 Ptype tapping screw(RoHS)
352-AM03008D041-E ¢3*8 Btypetapping screw (RoHS)
150-r4055900-e
152-u602015-e
154-k31505t0-e
155-63032i-e
180-pbr12c11s-e
162-10082007-e
power Xformer I/P:120V/60Hz TT0900008720 (RoHS)
line cord polar SVT FT-2 6FT double insulator (RoHS)
fuse 3.15A 250V 30mm UL/CSA /PSE (RoHS)
fuse holderHTB-32I 30mm UL/CSA (RoHS)
power switch PUSH BR12C11S (RoHS)
WIRE RED 18AWG 80mm 8mm#1015 (RoHS)
362-FE-00013-0LAE PCB support L TYPE t=1.6mmS.P.C.C 89*9*1.6T (RoHS)
311-ABS-00028-0BAE LEVEL KNOB 46077-W P.V.C.(RoHS)
306-ABS-00004-0BAE rear Plastic housing 268*213*102 A.B.S UL (RoHS)
176-wjce1-e
333-EVA-00096-0BAE
333-EVA-00097-0BAE
333-EVA-00132-0BAE
333-EVA-00133-0BAE
333-EVA-00220-0BAE
333-EVA-00188-0BAE
130-3f104z503-e
193-201815t2-e
352-HM03012D086-E
317-000-00037-0LAE
323-AL-00056-0LAE
333-EVA-00219-0BAE
351-AM03008A078-E
162-a040d005-e
wire connector pinCE-1 (RoHS)
EVA gasket wide side213*15*2.0mm(RoHS)
EVAgasket wide side213*15*1.0t (RoHS)
EVA gasket long side238*15*2.0mm (RoHS)
EVAgasket long side238*15*1.0t (RoHS)
EVAgasket long side225*15*1t UL(RoHS)
EVA gasket 170x5x1t (RoHS)
disc capacitor 0.1U 50V +80/-20% TAP(RoHS)
insulator (RoHS)
¢3*12 Btypetapping screw black (RoHS)
panel M3 solder t=0.3 (RoHS)
heat sink 83.5*50.5*27.5H
EVAgasket 150*15*1t UL(RoHS)
M3*8 machine screw (RoHS)
spkr wire red and black#1015 add #205 250 pin(RoHS)
302-AL-00020-1LCE rear board 270*215*2.5T SUB10 AL (RoHS)
335-NYL-05015-0BAE wire clip SB4F-2 black(RoHS)
14
4
3
4
1
1
1
1
1
1
2
2
1
1
2
2
2
2
1
1
1
1
1
1
6
1
1
2
T501
F501
for F501
SW501
C110
SUB10
Venture Series
15
SUB10
Venture Series
16
SUB10
Venture Series
17
SUB10
Venture Series
18
SUB10
Venture Series
19
SUB10
Venture Series
20
SUB10
Venture Series
, IC1
21
SUB10
Venture Series
22
SUB10
Venture Series
23
SUB10
Venture Series
24
SUB10
Venture Series
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement