OKIDATA OKIJET 2020 INK JET PRINTER Service Manual

Service Manual - OKIJET 2020
Chapter 0 Introduction
Front Cover
OKIJET 2020
INK JET PRINTER PRODUCTS
P/ N 59276601
Adobe Acrobat printable reference copy
of the OKIDATA Service Training Manual.
03/20/98
Note: This Adobe Acrobat version of the Okidata Service Training Manual was built with
the pictures rendered at 300 dpi, which is ideal for printing, but does not display well
on most displays.
OKIDATA has taken care to insure that the information is complete, accurate and up-to-date. However, OKIDATA assumes no
responsibility for errors or omissions which may occur. All the information provided is subject to change from time to time at the
sole discretion of OKIDATA.
Table of Contents
Page
Service Manual - OKIJET 2020
0 Introduction
Disclaimer/Copyright
About This Manual
Organization
....Section 1 - SERVICE CALL PROCEDURES
....Section 2 - REPAIR ANALYSIS PROCEDURES (RAPs)
....Section 3 - IMAGE QUALITY REPAIR ANALYSIS
PROCEDURES (RAPs)
....Section 4 - REPAIR / ADJUSTMENT PROCEDURES
....Section 5 - PARTS LIST
....Section 6 - GENERAL PROCEDURES
....Section 7 - WIRING DATA
How To Use This Manual
Reference Symbology
Special Symbols
Signal Nomenclature
DC Voltage Levels
Switches and Relay Contacts
1 Service Call Procedures
Introduction
....Printer Maintenance
....Initial Actions
....System Checkout / Final Action
2 Repair Analysis Procedures (RAPs)
Error LED On RAP
Power LED Blinking RAP
Low Ink LED(s) On RAP
Error LED Flashing RAP
1.1 Power on RAP
2.1 Selection/Indication RAP
6.1 Carriage TAP
6.2 Encoder RAP
8.1 Paper Feed RAP
9.1 Blank Print RAP
3 Image Quality RAPs
IQ 1 Image Defect Entry RAP
IQ 1 Image Defect Entry RAP Table
4 Repair / Adjustment Procedures
REP 1.0 Printhead
REP 1.1 Paper Tray Assembly
REP 1.2 Cartridge Cover
REP 1.3 Top Cover
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Table of Contents
REP 1.4 Exit Guide
REP 1.5 Paper Feed / Carriage Assy.
REP 1.6 Power Supply
REP 1.7 Main Control Board
REP 1.8 Waste Ink Pad
REP 1.9 Pump
REP 1.10 Maintenance Station
REP 1.11 Encoder
REP 1.12 Control Panel Assembly
REP 1.13 Paper Path Sensor (SW 1)
REP 1.14 Back Pad
REP 1.15 Printhead Ribbon Cable
REP 1.16 Ink Level Sensor
ADJ 2.0 Printhead Alignment
5 Parts List
PL 1.1 Printer Components
PL 2.1 Paper Feed / Carriage Assembly Components (Part 1 of
3)
PL 2.1 Paper Feed / Carriage Assembly Components (Part 2 of
3)
PL 2.1 Paper Feed / Carriage Assembly Components (Part 3 of
3)
Part Number Index
6 General Procedures
Diagnostics
....GP 1 Printhead Test
....GP 2 Printing with DOS
Product Specifications
....Physical Characteristics
....Electrical Requirements
....Printer Capabilities
....Supplemental Items
Printer Overview and Technical Overview Introduction
....Printer Overview
........Printer Specifications
........Features and Operation
........Safety Notes
........Printer Installation
....Printer Operation
........Loading the paper
........Test print mode
........Connecting the printer to a computer
........Control panel
........Printing
Page
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Table of Contents
....Printer Maintenance
........Cleaning
........Replacing the Printhead
........Troubleshooting
........Removal / Replacement of the printer components
Technical Overview
....Power and Control
........Standby power
........Run control functions
........Main Control Board
........Control Panel Assembly
........Bi-Directional Cable
....Printing and Priming
........Printing
........Print control
........Cleaning and Priming
....Ink Level Sensing
........Ink Cartridge Present
........Low Ink Detection
........Out of Ink Detection
....Carriage Drive
........Carriage drive
........Carriage movement at power on
....Encoder
........Status code
....Paper Supply / Paper Feed
........Paper supply
........Paper feed
........Load and eject mechanism
....Sensors and status indicators
........Sensors
........Status indicators
7 Wiring Data
Plug / Jack Location Index
Plug / Jack Location Drawings
....Figure 7-1. Main Control Board and Power Supply
....Figure 7-2. Carriage Assembly (Bottom View)
....Figure 7-3. Carriage
....Figure 7-4. Front View
Block Schematic Diagrams (BSDs)
....Chain 1 AC/DC Power Generation
....Chain 2 Selection and Indication
....Chain 3 Machine Run Control
....Chain 8 Paper Feed
Page
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
Table of Contents
....Chain 9 Print Control
Page
119
Page: 1
Service Manual - OKIJET 2020
Chapter 0 Introduction
Disclaimer/Copyright
Disclaimer
This document may not be reproduced without the written permission of Okidata Training and
Publications. Every effort has been made to ensure the accuracy of the information contained in this
training course. Okidata is not responsible for errors beyond its control.
Copyright 1997 by Okidata
All rights reserved.
Edited by:
Okidata Training and Publications
Prepared by:
Multinational Customer and Service Education
Xerox Corporation, Rochester, New York 14644
Please address any comments on this publication to:
Mailing Address:
OKIDATA Training and Publications
532 Fellowship Road
Mt. Laurel, NJ 08054-3499
Web Site www.okidata.com
Telephone 609- 235- 2600
Facsimile 609- 222- 5320
Okilink Technical Training
Copyright Listing
OKIDATA is a registered trademark of Oki Electric Industry Company, Ltd.; marques deposee de Oki
Electric Industry Company, Ltd.; marca registrada, Oki Electric Industry Company, Ltd.
XEROX is a trademark of Xerox Corporation
Notice
All service documentation is supplied for informational purposes only. Okidata service documentation is
intended for use by certified, product trained service personnel only. Okidata does not warrant or
represent that such documentation is complete, nor does Okidata represent or warrant that it will notify or
provide to such customer any future changes to this documentation. Customer performed service of
equipment, or modules, components or parts of such equipment may affect the warranty offered by
Okidata with respect to such equipment. You should consult the applicable warranty for its terms
regarding customer or third party provided service. If the customer services such equipment, modules,
components or parts thereof, the customer releases Okidata from any and all liability for the customer
actions, and the customer agrees to indemnify, defend and hold Okidata harmless from any third party
claims which arise directly or indirectly from such service.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 2
Service Manual - OKIJET 2020
Chapter 0 Introduction
About This Manual
This manual contains Repair Analysis Procedures, Repair Procedures, Adjustment Procedures, Parts
List, Diagnostic Procedures, and Wiring Data information that will enable a Service Representative to
repair the Printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 3
Service Manual - OKIJET 2020
Chapter 0 Introduction
Organization
This manual is divided into seven sections. The title and description of each section are listed below.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 4
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 1 - SERVICE CALL PROCEDURES
This section contains the following:
Initial Actions / System Checks
System Checkout
Final Action
Initial Actions / System Checks
This diagram identifies how to collect the data necessary to decide how to proceed with the service call. It
classifies the problem and refers you to the appropriate Repair Analysis Procedure.
System Checkout
The System Checkout procedure is used to verify that the printer is operating properly after a repair has
been made.
Final Action
The Final Action procedure identifies the steps that must be performed before finishing the repair.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 5
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 2 - REPAIR ANALYSIS PROCEDURES (RAPs)
This section contains the Repair Analysis Procedures (RAPs) necessary to repair faults. When using a
RAP, always exit the procedure when the fault is fixed. Do not perform the remaining steps.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 6
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 3 - IMAGE QUALITY REPAIR ANALYSIS PROCEDURES (RAPs)
This section contains the Repair Analysis Procedures (RAPs) necessary to repair print quality faults. The
first RAP, IQ 1 Image Defect Entry RAP, is used to classify a print quality problem and will reference the
RAP to be used to repair the problem. When using a RAP, exit the procedure when the fault is fixed. Do
not perform the remaining steps.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 7
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 4 - REPAIR / ADJUSTMENT PROCEDURES
This section contains the repair and adjustment procedures for the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 8
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 5 - PARTS LIST
This section contains the detailed Parts List for the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 9
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 6 - GENERAL PROCEDURES
This section contains Diagnostic Procedures and Product Specifications for the Printer. An Overview and
Technical Overview section are also included.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 10
Service Manual - OKIJET 2020
Chapter 0 Introduction
Section 7 - WIRING DATA
This section contains Plug/ Jack Location Drawings and Block Schematic Diagrams (BSDs).
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 11
Service Manual - OKIJET 2020
Chapter 0 Introduction
How To Use This Manual
The Service Call Procedures will direct you to the proper section of the Service Manual.
You should begin the service call with the Initial Actions / System Checks Procedure. From there, you will
be referenced to either Section 2, Status Indicator RAPs or Section 3, Image Quality RAPs.
If you are sent to Section 3, you will perform the IQ 1 Image Defect Entry RAP to classify the print quality
problem. You will then be directed to the proper RAP to begin your troubleshooting. From these RAPs
you may be referenced to other sections of the manual to make checks, adjustments or to replace parts.
When you have made a repair, return to the System Checkout / Final Action to complete the call.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 12
Service Manual - OKIJET 2020
Chapter 0 Introduction
Reference Symbology
Notes, adjustments, and parts lists support the checklists and the RAP information. The symbols that
refer to this supportive data are shown below.
Note
This symbol is used to refer to notes found on the same page.
Adjustments
ADJ 4.1 This symbol refers to an adjustment procedure located in Section 4 of
this Service Manual. The number adjacent to the symbol indicates the number
that is assigned to that adjustment.
Parts List
PL 10.6
Refers to the parts list located in Section 5 of this Service Manual. The number
after the PL designation indicates the number that is assigned to that part.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 13
Service Manual - OKIJET 2020
Chapter 0 Introduction
Special Symbols
Descriptions of all commonly used graphic symbols are included in order to aid in troubleshooting when
using the RAPs.
Interrupt Horizontal Signal
This indicates the continuation of a signal line which is interrupted in a horizontal
direction.
Standby Power Input
This indicates the continuation of a standby power line which is interrupted in the vertical
direction.
Left to Right Flow
This indicates the direction of signal flow.
Feedback
This indicates a feedback signal.
Flag
This is used to identify an area of a Circuit Diagram that you should check.
Ground
This indicates a machine ground.
LED / Phototransistor Sensor
This type of sensor is used in the paper path. It uses reflected light to switch the sensor
off and on.
Without Tag Change
This signal indicates that the area the triangle points to has not been modified by the tag
number in the circle.
This symbol indicates that the entire page has not been modified by the tag number in
the circle.
With Tag Change
This symbol indicates that the area the triangle points to has been modified by the tag
number in the circle.
This symbol indicates that the entire page has been modified by the tag number in the
circle.
WARNING
A warning is used to alert the personnel to an operating or maintenance
procedure, practice, or condition that, if not strictly observed, could result in injury
or loss of life.
CAUTION
A caution is used to alert the personnel to an operating or maintenance procedure,
practice or condition that, if not strictly observed, could result in damage to, or destruction
of, equipment.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 14
Service Manual - OKIJET 2020
Chapter 0 Introduction
Signal Nomenclature
The signal is named to imply the condition of the machine when the signal is available.
For example:
Logic state when the signal is available in its named state. In this case, the signal is LOW when a
document jam is sensed.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 15
Service Manual - OKIJET 2020
Chapter 0 Introduction
DC Voltage Levels
DC voltages should be measured between the test point and machine GND, unless instructed otherwise.
The table below shows the values of the voltages.
Nominal Voltage
+5 VDC
+42 VDC
Logic State
H
L
H
L
Actual Voltage Ranges
+4.8 to +5.2 VDC
0.0 to +1.0 VDC
+39.0 to +44.0 VDC
0.0 to +3.0 VDC
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 16
Service Manual - OKIJET 2020
Chapter 0 Introduction
Switches and Relay Contacts
Safety interlock switch that is open.
Safety interlock switch that is closed.
Switch or relay contacts with momentary contacts shown normally open.
Switch or relay contacts with momentary contacts shown normally closed.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 17
Service Manual - OKIJET 2020
Chapter 1 Service Call Procedures
Introduction
Use the Service Call Procedures as a maintenance guide when performing any service on the printer.
Printer Maintenance - This section contains a list of the printer subsystem components to be cleaned
and /or lubricated and the cleaning and lubricating materials to be used, when that subsystem is
accessed during a repair.
Initial Actions / System Checks - This diagram identifies and classifies the printer problem and refers
you to the appropriate RAP in order to repair the problem. When the problem has been repaired,
perform the System Checkout / Final Action.
System Checkout / Final Action - This procedure should be completed at the end of every repair call
to ensure that the printer is operating properly.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 18
Service Manual - OKIJET 2020
Chapter 1 Service Call Procedures
Printer Maintenance
Introduction
When the printer is being serviced, the following maintenance procedure should be performed.
Procedure
Clean the following parts every time the printer is serviced:
Description
Cover
Paper Feed Roller
Paper Feed Pinch rollers and Paper Feed Guide
Maintenance Station
Procedure
Clean using a Lint Free Tissue and water.
Clean using a Lint Free Tissue and water.
Clean using a Lint Free Tissue and water.
Clean using a Lint Free Tissue and water.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 19
Service Manual - OKIJET 2020
Chapter 1 Service Call Procedures
Initial Actions
1. QUESTION THE OPERATOR.
2. VERIFY, CLASSIFY AND REPAIR THE PROBLEM.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 20
Service Manual - OKIJET 2020
Chapter 1 Service Call Procedures
System Checkout / Final Action
Reset the Ink Level Sensing count to zero. Perform the following:
Install a Color Printhead with empty ink cartridges.
Run a Test Print.
Remove the Printhead and install a Color Printhead with full ink cartridges.
Run a Test Print.
The NVM counts are now set to zero.
Print a file.
The Printer prints the selected file.
Y N
Refer to Initial Action / System Checks to begin your repair.
Evaluate the print.
Is the image quality acceptable?
Y N
Go to the image quality RAP identified by the IQ 1 Image Defect Entry RAP (Section 3).
Print and check the "Printing Alignment Test pattern".
The alignment is good.
Y N Go to the Printhead Alignment Procedure (Section Four).
Clean exterior of machine. Use a lint free tissue and water. Provide a sample of the Test Print.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 21
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
Error LED On RAP
Initial Action:
Ensure a color printhead is installed.
Remove the power cord from the printer for 10 seconds, then reinstall it.
Press the Power switch.
The Error LED is on steady.
Y
N
The Error LED is flashing.
Y
N
Press and hold the Resume/FF button for 2 seconds to print the demo print.
The Error LED is steady.
Y
N
The Error LED is flashing.
Y
N
Check the interface cable and connectors for an open wire or bad
connection. If OK, replace the Main Control Board.
Go to Error LED Flashing RAP.
Remove the power cord from the printer for 10 seconds, then reinstall it.
Press and hold the Power switch for about 2 seconds.
The carriage was noisy.
Y
N
The printhead stopped at each ink cartridge during the power-on cycle.
Y
N
Go to 6.2 Encoder RAP.
A
B
C
D
Go to 8.1 Paper Feed RAP.
Go to 6.1 Carriage RAP.
Go to Error LED Flashing RAP.
One or more low ink LED(s) are blinking.
Y
N
Go to 6.1 Carriage RAP.
Go to Low Ink LED(s) on RAP.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 22
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
Power LED Blinking RAP
Remove the power cord from the printer for 10 seconds, the reinstall it.
The Power LED blinks.
Y
N
Printer is OK.
Go to 2.1 Selection/Indication RAP.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 23
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
Low Ink LED(s) On RAP
Initial Action:
Ensure all the ink cartridges are full and properly seated.
Go to Flags 1 and 2. Check the wires and connections for an open circuit. The wires are good.
Y
N
Repair the wires or connections if possible.
Replace the main control board.
If the problem still exists, replace the Printer.
Replace the Ink Level Sensor (PL 2.1).
Replace the main control board.
If the problem still exists, replace the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 24
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
Error LED Flashing RAP
Note: This procedure will work only when the Error LED is flashing.
Note: In the following procedure, the Error LED and Power LED will be used to display an 8 bit binary
error code. The LEDs will flash in 1/2 second intervals. The code will be displayed 4 bits at a time. The
LED code is as follows (See Figure 1):
1 = Both Error and Power LEDs lit
0 = Error LED only is lit
1. Press and release the Resume/ FF button, while observing the Error and Power LEDs.
2. 4 bits will be flashed in 1/ 2 second intervals followed by a pause, then 4 more bits in 1/ 2 second
intervals. After the cycle, the Error LED will continue to flash.
3. Determine the code and go to the Error Code Chart (Table 1) for the corrective action.
4. Repeat step 1 as many times as necessary to determine the code.
Error Code
1000 1000
1000 1100
1100 1000
1110 1000
1100 1111
Error Description
ROM error
RAM error
EPROM error
CPU error
Carriage home position error
Corrective Action
Replace the Main Control Board
Replace the Main Control Board
Replace the Main Control Board
Replace the Main Control Board
Go to 6.1 Carriage RAP
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 25
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
1.1 Power on RAP
Refer to Figure 1. There is +42 VDC measured on the Main Control Board.
Y
N
Disconnect the power cord.
Check fuse F1 on the Power
Supply.
F1 is blown.
Y
N
Go to Flag 1 (Figure 2) and check the wires for an open circuit. If good, replace the Power
Supply. If problem still exists, replace the Main Control Board.
Replace the blown fuse.
If the problem is not corrected, replace the Power Supply (PL 1.1).
Refer to Figure 1. There is +5 VDC measured on the Main Control Board.
Y
N
Go to Flag 2 and check for a short to ground. If OK, replace the Power Supply. If problem still
exists, replace Main Control Board.
Replace the Main Control Board before replacing the Control Panel Assembly.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 26
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
2.1 Selection/Indication RAP
Load paper.
Disconnect and then reconnect the power cord while observing the LEDs.
All LEDs light momentarily when the power cord is reconnected.
Y
N
One or more LEDs light.
Y
N
Go to 1.1 Power on RAP.
Go to Flag 1 and Flag 2 and check for an open wire. If OK, replace the Control Panel
Assembly.
All LEDs go out in approximately 10 seconds.
Y
N
If the Power LED remains on (flashing), go to Flag 3 and check for an open wire. If OK,
replace the Control Panel Assembly.
Press and hold the Power button for approximately 2 seconds to turn on the printer.
Press and hold the Resume/FF button for 2 seconds.
Paper feeds.
Y
N
Go to Flag 5 and check for an open wire.
If good, go to 8.1 Paper Feed RAP.
A
A
Press the Cartridge Change button.
The carriage moves to the center position.
Y
N
Go to Flag 4 and check for an open wire.
If OK, replace the Control Panel Assembly.
For printer set up problems when printing from a DOS application, consult GP 2 Printing with
DOS Procedure in Section 6.
Examples of printer set up problems.
When trying to print from the host, the paper continues to linefeed without outputting any print.
Just a few lines of data are printed and then the paper continues to line feed without printing.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 27
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
6.1 Carriage TAP
Disconnect and then reconnect the power cord.
Press and hold the Power switch.
The carriage moves.
Y
N
Go to Flag 1 and check the ribbon cable for being open or damaged.
Go to Flag 2 and check for an open circuit. If the wire is good, replace the Main
Control Board.
Check / replace the ribbon carriage cable.
Check the teeth on the belt.
Check the teeth on the carriage motor.
Check for 42 volts.
If 42 volts aren't being supplied by the power supply, replace the power supply.
Check / replace the carriage motor.
Perform the following:
Check that the Printhead ribbon cable going to CN4 on the Main Control Board is
connected properly.
Go to Flag 2 and Flag 3 and check for an open circuit.
If the wires are good, replace the Printhead Ribbon Cable (PL 2.1).
If the problem continues replace the Main Control Board (PL 1.1).
Check / replace the ribbon carriage cable.
Check the teeth on the belt.
Check the teeth on the carriage motor.
Check for 42 volts.
If 42 volts aren't being supplied by the power supply, replace the power
supply.
Check / replace the carriage motor.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 28
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
6.2 Encoder RAP
Go to Flag 1 and check the ribbon
Go to Flag 4 and check for an open circuit.
Replace the Encoder.
Go to 6.1 Carriage RAP.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 29
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
8.1 Paper Feed RAP
Clear any paper in the printer.
Disconnect and then reconnect the power cord.
Press and hold the Power switch for about 2 seconds.
Press and hold the Resume/FF button for 2 seconds to print the demo print.
The paper feeds or partially feeds.
Y
N
Check that the Paper Tray is installed correctly (REP 1.1)
Go to Flag 1 and check the cam sensor circuit for an open.
If OK, go to Flag 3 and check for an open circuit. If paper feed motor circuit is
defective, replace the paper feed motor.
If the wires are good, replace the Main Control Board.
Go to Flag 2 and check the paper feed switch circuit for an open.
If OK, go to Flag 3 and check for an open circuit.
Replace the Back pad.
If the problem still exists, replace the Main Control Board.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 30
Service Manual - OKIJET 2020
Chapter 2 Repair Analysis Procedures (RAPs)
9.1 Blank Print RAP
Initial Action:
Ensure that the Printhead latch is positioned towards the rear.
Unlatch the Printhead, reset the Printhead and latch it back into position. If problem still exists:
Replace the Printhead.
Go to Flag 1 and check the ribbon cable for being damaged.
Check the terminals of J11 on the Carriage Assembly and J12 on the Ink Cartridge for being
contaminated or damaged. Clean or repair as necessary.
If the problem still exists, replace the Printhead Ribbon Cable (PL 2.1).
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 31
Service Manual - OKIJET 2020
Chapter 3 Image Quality RAPs
IQ 1 Image Defect Entry RAP
1. Print the Test Print:
a. Load paper into the Paper Tray.
b. Press and hold the Power on / Reset button for approximately 2 seconds and then release, to switch
the Printer power off.
c. While pressing and holding the Resume/ FF button press and release the Power on / Reset button.
The printer prints the test print shown in Figure 1. When the test print is complete, the printer initializes
and returns to the Ready status.
d. If the test print fails to print, repeat steps a through c.
2. Refer to the DEFECT Column in Table 1 that best describes the image quality problem.
3. If the problem is with external input only, replace the Main Control Board.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 32
Service Manual - OKIJET 2020
Chapter 3 Image Quality RAPs
IQ 1 Image Defect Entry RAP Table
DEFECT
Blank print
White horizontal lines and
Streaks
Print is faint or missing
Blurry or jagged vertical
lines
Print image is clipped or
off edge of media
CAUSE
Printhead
The Printhead
nozzles may be
blocked.
SOLUTION
1. Remove and reinstall the Printhead.
2. Press the Cartridge Change / Clean
button for 2 seconds to clean and restore
the Printhead. Repeat if necessary.
If the problem still exists go to the 9.1 Blank
Print RAP.
Perform the following:
1. Press the Cartridge Change / Clean
button for 2 seconds to clean and restore
the Printhead.
2. Make another Test Print. If the print still
has lines and streaks repeat the above
process up to 5 times.
3. If the problem still exists, replace the
Printhead.
Replace the paper.
A non
recommended
paper is being used
or the paper is
damp.
Defective Cartridge. Perform the following:
1. Press and hold the Cartridge Change /
The ink supply may
Clean button for 2 seconds to clean and
be nearly empty.
restore the Printhead.
The Printhead
nozzles may be
2. Run a Test Print. If the print is still faint,
blocked.
repeat the process up to 2 more times.
3. If the problem is still not corrected
replace the Printhead.
Perform ADJ 2.0 Printhead Alignment
Printhead
Procedure
Alignment
If the problem still exists switch the printer to
the High Quality print mode (in the printer
driver..)
Turn the paper over to print on the opposite
Paper
side.
Ensure that the Print Driver setup has the
Print off edge of
correct selection of media size and type.
media.
Document margins Adjust margins in the application as
may exceed printer necessary.
margins.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 33
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.0 Printhead
Parts List on PL 2. 2
Removal
1. Open the Cartridge Cover (PL 1.1).
2. Center the carriage using either of the following procedures:
Press the Cartridge Change / Clean button.
WARNING: Switch off the power. Disconnect the power cord from the wall outlet.
Grasp and manually move the belt (PL 2.1) in order to center the Printhead (Figure 1).
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If
necessary, prime the printhead after reinstallation. (See below to Refer to the Replacement / Priming
section of this procedure.)
3. Move the Printhead lock lever toward the front of the printer.
4. Lift and remove the Printhead. Store it in the Storage Box.
Replacement / Priming
1. Install the Printhead onto the Printhead vertical guide.
2. Move the Printhead lock lever toward the rear of the printer.
3. Close the Cartridge Cover.
4. Press the Resume / FF button to prime the Printhead.
NOTE: The optional high capacity printhead is shown. Refer to the User's Documentation for illustrations
of the standard printhead.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 34
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.1 Paper Tray Assembly
Parts List on PL 1. 1
Removal
1. Remove the Output Tray (PL 1.1).
2. Press the two handles toward the rear of the printer to release the latches (Figure 1).
3. Pivot the Paper Tray Assembly toward the back of the printer to disengage the three tabs at the bottom
of the Paper Tray Assembly from the tabs on the Paper Feed / Carriage Assembly.
4. Lift the Paper Tray Assembly from the printer.
Replacement
1. Retract the moveable face of the Paper Tray Assembly by pressing it toward the back of the Paper
Tray Assembly.
2. Insert the Paper Tray Assembly into the printer (with bottom of tray touching the bottom of the tray
opening on the printer) ensuring the moveable face is behind the white cam (near the bottom, on the left).
See Figure 2.
3. Engage the three tabs at the bottom of the Paper Tray Assembly with the tabs on the Paper Feed /
Carriage Assembly.
4. Rotate the Paper Tray Assembly toward the front of the printer.
5. Engage the two latches by gently pulling the handles downward and toward the front of the printer until
the latches snap into position.
6. Reinstall the Output Tray.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 35
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.2 Cartridge Cover
Parts List on PL 1. 1
Removal
1. Open the Cartridge Cover (PL 1.1).
2. Utilizing a screwdriver or similar tool, slightly separate the Cartridge Cover and Top Cover at either
pivot to release the Cartridge Cover pivot from the Top Cover (Figure 1).
3. Lift the Cartridge Cover from the printer.
Replacement
1. Insert either Cartridge Cover pivot into the corresponding Top Cover pivot hole.
2. Utilizing a screwdriver or similar tool, slightly separate the Cartridge Cover and Top Cover at the
opposite pivot.
3. Position the Cartridge Cover pivot to engage with the pivot hole of the Top Cover.
4. Close the Cartridge Cover.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 36
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.3 Top Cover
Parts List on PL 1. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the cartridge removed for long periods of time
will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after
reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord from the wall outlet.
2. Remove the Output Tray (PL 1.1).
3. Remove the Paper Tray Assembly (REP 1.1).
4. Remove the Cartridge Cover (REP 1.2).
5. Lay the printer on it's back; release the three front latch tabs (Figure 1).
CAUTION: While removing the Top Cover from the printer, take care not to damage the ribbon cable that
is connected to the Control Panel Assembly, which is located inside the Top Cover.
NOTE: The rear of the Top Cover has three locator tabs and two latch tabs.
6. Return the printer to its normal operating position. Lift and hold the front of the cover slightly while
releasing the two rear latch tabs. Then lift the rear of the cover and pivot towards the FRONT of the
printer to remove.
Replacement
1. Ensure the ribbon cable is properly routed and not twisted during Top Cover installation.
2. If previously disconnected, reconnect ribbon cable to the Control Panel Assembly.
3. Position the Top Cover on the printer. Align and latch the rear latches; then the front latches.
4. Reinstall the following:
a. Cartridge Cover (REP 1.2)
b. Paper Tray Assembly (REP 1.1)
c. Output Tray (PL 1.1)
d. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 37
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.4 Exit Guide
Parts List on PL 2. 2
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord from the wall outlet.
2. Remove the Output Tray (PL 1.1).
3. Remove the Cartridge Cover (REP 1.2).
4. Position both thumbs at the lower, front corners of the Exit Guide (Figure 1). Apply modest pressure
simultaneously toward the rear and up to unlatch the Exit Guide.
5. Rotate the guide approximately 90° up and toward the rear of the printer.
6. Lift the Exit Guide from the printer.
Replacement
1. Hold the Exit Guide so the star wheels (10) are facing the front of the printer.
2. Lower the Exit Guide into the printer to engage the pivots with the slots in the Paper Feed / Carriage
Assembly.
3. Rotate the Exit Guide completely toward the front of the printer.
4. Position both thumbs at the lower, front corners of the Exit Guide (Figure 1). Apply moderate pressure
simultaneously toward the rear and down to latch the Exit Guide.
5. Reinstall the Cartridge Cover (REP 1.2).
6. Reinstall the Output Tray (PL 1.1).
7. Reinstall the Printhead (REP 1.0).
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 38
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.5 Paper Feed / Carriage Assy.
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the Output Tray (PL 1.1).
3. Remove the Paper Tray Assembly (REP 1.1).
4. Remove the Cartridge Cover (REP 1.2).
5. Remove the Top Cover (REP 1.3).
6. Loosen screw; disconnect ground wire from ground plate near front, left corner of Paper Feed /
Carriage Assembly (Figure 1).
7. Disconnect ground wire from grounding plate at right side of printer (Figure 2).
8. Remove the screws (2) from the two front corners of the Paper Feed / Carriage Assembly (Figure 3).
9. Lift the front of the assembly slightly, then slide the assembly toward the front of the printer until it
contacts the front wall of the base.
10. Lift the front of the assembly to access the Main Control Board ribbon cable connectors, CN3 & CN4;
disconnect from the Main Control Board (Figure 4).
11. Remove the assembly from the base.
Replacement
1. Lift the front of the assembly to access the Main Control Board ribbon cable connectors, CN3 & CN4;
reconnect to the Main Control Board (Figure 4 - see above).
2. Allow the Paper Feed / Carriage Assembly to rest on the printer base. Slide the assembly rearward to
engage the rear mounts.
3. Reinstall the two front screws.
4. Reconnect the ground wire to the ground plate on the right side of the printer.
5. Reconnect the ground wire to the ground plate on the left, front corner of the printer; tighten screw.
6. Reinstall the following:
a. Top Cover (REP 1.3)
b. Cartridge Cover (REP 1.2)
c. Paper Tray Assembly (REP 1.1)
d. Output Tray (PL 1.1)
e. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 39
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.6 Power Supply
Parts List on PL 1. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink to dry out. Image quality defects a blank page could result. If necessary, prime the
printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the Power. Disconnect the power cord at the wall outlet.
2. Remove the Output Tray (PL 1.1).
3. Remove the Paper Tray Assembly (REP 1.1).
4. Remove the Cartridge Cover (REP 1.2).
5. Remove the Top Cover (REP 1.3).
6. Remove the Paper Feed / Carriage Assembly (REP 1. 5).
7. Disconnect Power Supply power cord connector CN1 from the Power Supply (Figure 1).
8. Remove the four mounting screws.
9. Slide the Power Supply toward the right side of the printer to disengage Power Supply connector CN2
from the Main Control Board connector CN1; lift the Power Supply from the printer.
Replacement
1. Position the Power Supply into the printer base.
2. Slide the Power Supply toward the left side of the printer to engage Power Supply connector CN2 with
the Main Control Board (Figure 1).
3. Install the four mounting screws.
4. Reconnect the Power Supply power cord connector CN1.
5. Replace the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Top Cover (REP 1.3)
c. Cartridge Cover (REP 1.2)
d. Paper Tray Assembly (REP 1.1)
e. Output Tray (PL 1.1)
f. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 40
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.7 Main Control Board
Parts List on PL 1. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the cartridge in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the Output Tray (PL 1.1).
3. Remove the Paper Tray Assembly (REP 1.1).
4. Remove the Cartridge Cover (REP 1.2).
5. Remove the Top Cover (REP 1.3).
6. Remove the Paper Feed / Carriage Assembly (REP 1. 5).
7. Remove the Power Supply (REP 1.6).
8. Disconnect Main Control Board connector CN2 from the Main Control Board (Figure 1).
NOTE: The two screws securing the PC interface cable connector to the Main Control Board are longer
than the others. Ensure to replace them in their correct positions.
9. Remove the eight mounting screws and ground wire (Figure 1).
NOTE: It may be necessary to detach the ribbon cable and ferrite from the printer base before removing
the Main Control Board.
NOTE: Exercise care not to deform the two PC interface cable connector wire-form locks during Main
Control Board removal.
10. Remove the Main Control Board.
Replacement
NOTE: There are 2 different length screws securing the Main Control Board. Be sure to reinstall the two
longer screws through the PC interface cable connector.
1. Position the Main Control Board into the printer base.
2. Reinstall the ground wire as per Figure 1.
3. Reinstall mounting screws.
4. Reconnect connector CN2 to the Main Control Board.
5. If previously detached, reattach the ribbon cable and ferrite to the printer base.
6. Replace the following:
a. Power Supply (REP 1.6)
b. Paper Feed / Carriage Assembly (REP 1. 5)
c. Top Cover (REP 1.3)
d. Cartridge Cover (REP 1.2)
e. Paper Tray Assembly (REP 1.1)
f. Output Tray (PL 1.1)
g. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 41
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.8 Waste Ink Pad
Parts List on PL 1. 1
Replacement
NOTE: There are 2 different length screws securing the Main Control Board. Be sure to reinstall the two
longer screws through the PC interface cable connector.
1. Position the Main Control Board into the printer base.
2. Reinstall the ground wire as per Figure 1.
3. Reinstall mounting screws.
4. Reconnect connector CN2 to the Main Control Board.
5. If previously detached, reattach the ribbon cable and ferrite to the printer base.
6. Replace the following:
a. Power Supply (REP 1.6)
b. Paper Feed / Carriage Assembly (REP 1. 5)
c. Top Cover (REP 1.3)
d. Cartridge Cover (REP 1.2)
e. Paper Tray Assembly (REP 1.1)
f. Output Tray (PL 1.1)
g. Printhead (REP 1.0)
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Paper Feed / Carriage Assembly (REP 1. 5)
3. Remove Waste Ink Pad retainer by releasing the four locking tabs with screwdriver or other similar tool
(Figure. 1).
Replacement
1. Ensure flange on one end of the pad retainer is toward the right side of the printer.
2. Snap the retainer into position.
3. Replace the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Top Cover (REP 1.3)
c. Cartridge Cover (REP 1.2)
d. Paper Tray Assembly (REP 1.1)
e. Output Tray (PL 1.1)
f. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 42
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.9 Pump
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality defects or a blank page could result. If necessary,
prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Paper Feed / Carriage Assembly (REP 1. 5)
3. Remove the Pump from the Paper Feed / Carriage Assembly.
a. Note routing of inlet tube; disconnect tube at connector beneath Maintenance Station (Figure 1).
b. Note routing of outlet tube; remove cable tie; slide tube through frame.
c. Remove two Pump mounting screws. (Figure 2).
d. Slide pump from motor shaft.
Replacement
1. Install the pump onto the motor shaft.
2. Reinstall the two mounting screws.
CAUTION: Ensure the pump tubing is not kinked or otherwise restricted during reinstallation.
3. Route inlet tube as shown in Figure 1; reconnect; clamp into position.
4. Route outlet tube as shown in Figure 1; install two cable ties on tube at either side of frame to ensure
tube exits onto Waste Ink Pad.
5. Reinstall the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Top Cover (REP 1.3)
c. Cartridge Cover (REP 1.2)
d. Paper Tray Assembly (REP 1.1)
e. Output Tray (PL 1.1)
f. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 43
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.10 Maintenance Station
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank page could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
3. Observe the routing of the tube from the Maintenance Station to the connector located below the
Maintenance Station. Disconnect this tube at the tube connector.
4. Move the Printhead carriage to the extreme right side of the printer.
5. Remove the mounting screw (Figure 1).
6. Lift and hold the left side of the paper pressure baffle approximately six millimeters away from the
Maintenance Station.
NOTE: Observe the tube routing during Maintenance Station removal.
7. Slide the Maintenance Station toward the front of the printer to disengage the mounting tabs, then lift
upward to remove Maintenance Station from the printer.
Replacement
CAUTION: Ensure the Printhead carriage is positioned to the extreme right side of the printer.
1. Route the Maintenance Station tube as observed during removal.
2. Lift and hold the left side of the paper pressure baffle approximately six millimeters away from the
Maintenance Station.
3. Lower the Maintenance Station into position to insert the mounting tabs.
4. Slide the Maintenance Station toward the rear of the printer to engage the mounting tabs.
5. Secure with mounting screw (machine threads).
6. Connect tube to its mating connector.
7. Ensure tube is routed between the pinch arm and the Maintenance Station body (Figure 2).
8. Reinstall the following:
a. Top Cover (REP 1.3)
b. Cartridge Cover (REP 1.2)
c. Paper Tray Assembly (REP 1.1)
d. Output Tray (PL 1.1)
e. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 44
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.11 Encoder
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank page could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Paper Output shelf (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Paper Feed / Carriage Assembly (REP 1. 5)
f. Maintenance Station (REP 1.10).
3. Remove the belt (PL 2.1) from the carriage motor pulley (right end).
4. Remove the belt from the Encoder pulley (left end).
CAUTION: A ribbon cable is attached to the bottom of the carriage assembly. Do not damage it while
removing the carriage assembly.
5. Rotate the carriage shaft cams so that their flats are aligned with the sides of the slot on each side
frame (Figure 1).
NOTE: Expect moderate to heavy resistance when removing carriage end cams from printer side frames.
CAUTION: Ensure no portion of carriage is beneath ink level sensor during carriage removal.
Simultaneously slide both cams from their respective slots (Figure 2).
CAUTION: Take care not to damage ribbon cable while removing the carriage.
6. Remove the carriage from printer side frames (Figure 2).
7. Position the Paper Feed / Carriage Assembly as shown in Figure 3..
8. Disconnect the Encoder connector (J4) from the Relay BOARD (Figure 3).
NOTE: Observe Encoder harness routing before removing Encoder.
9. Release the Encoder harness from the carriage tabs.
10. Return the Paper Feed / Carriage Assembly to its upright position.
11. Remove the screw and ground strap (Figure 4).
12. Remove the two Encoder plate mounting screws; remove the Encoder plate and Encoder (Figure 4).
13. Disconnect harness from Encoder.
14. Remove the screw securing Encoder to Encoder plate; remove Encoder; retain spring.
Replacement
1. Position and hold the spring on the plate; install Encoder on the plate; reinstall the screw securing
Encoder to the plate, but DO NOT tighten.
2. Route the Encoder harness through Paper Feed / Carriage Assembly.
3. Reinstall Encoder on Paper Feed / Carriage Assembly; install two mounting screws and the ground
strap.
4. Reconnect Encoder harness (J4) to Relay Board; secure harness to carriage tabs.
Caution: It is physically possible to cross-connect the Encoder Harness (J4) and the Low-ink Sensor (J2)
on the Relay Board since they use the same type of connector. By doing so, the Main Logic Board may
be damaged.
5. Reinstall Maintenance Station; reinstall the machine screw.
6. Reconnect Maintenance Station tube.
7. Ensure tube is properly located behind the pinch arm. Consult Maintenance Station Replacement, REP
1.10.
8. Reinstall carriage into Paper Feed / Carriage Assembly. Ensure carriage ribbon cable is properly
secured and not twisted.
9. Rotate both carriage shaft cams to align pointer with index mark (Figure 5).
10. Reinstall carriage belt onto Encoder pulley (left side).
11. Reinstall carriage belt onto drive motor pulley.
12. Tighten screw that secures Encoder to the plate.
13. Ensure both ground straps (left and right side) are firmly contacting the carriage shaft. Reform straps
as required.
14. Reinstall the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Top Cover (REP 1.3)
c. Cartridge Cover (REP 1.2)
d. Paper Tray Assembly (REP 1.1)
e. Output Tray (PL 1.1)
f. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 45
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.12 Control Panel Assembly
Parts List on PL 1. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank page could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
3. Position the Top Cover on its top.
NOTE: There is non-captured hardware under the Control Panel Assembly. DO NOT reposition the Top
Cover with the control panel assembly board removed.
4. Remove the mounting screws (3) from the Control Panel Assembly; remove the board (Figure 1).
5. Disconnect the ribbon cable from the board.
Replacement
1. Connect the ribbon cable to the Control Panel Assembly.
2. Ensure the buttons and lenses are properly positioned in the Top Cover. Carefully install the board into
the Top Cover. Secure with the three mounting screws.
3. Reinstall the following:
a. Reinstall the Top Cover (REP 1.3).
b. Reinstall the Cartridge Cover (REP 1.2).
c. Reinstall the Paper Tray Assembly (REP 1. 1).
d. Reinstall the Output Tray (PL 1.1).
e. Reinstall the Printhead (REP 1.0).
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 46
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.13 Paper Path Sensor (SW 1)
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank print could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Exit Guide (REP 1.4)
f. Paper Feed / Carriage Assembly (REP 1. 5)
3. Position the Paper Feed / Carriage Assembly as shown in Figure 1.
4. Disconnect J3 from the Relay Board. See Figure 1.
5. Remove mounting screw.
6. Remove Paper Path Sensor.
Replacement
1. Position the Paper Path Sensor (SW 1) in the Paper Feed / Carriage Assembly. Reinstall the mounting
screw.
2. Connect J3 to the Relay BOARD.
3. Reinstall the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Exit Guide (REP 1.4)
c. Top Cover (REP 1.3)
d. Cartridge Cover (REP 1.2)
e. Paper Tray Assembly (REP 1.1)
f. Output Tray (PL 1.1)
g. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 47
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.14 Back Pad
Parts List on PL 2. 1
Removal
CAUTION: Leaving the Printhead removed for long periods of time will cause the ink nozzles to dry out.
Image quality problems or a blank print could result. If necessary, prime the printhead after reinstallation.
(REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Exit Guide (REP 1.4)
f. Paper Feed / Carriage Assembly (REP 1. 5)
3. Position the Paper Feed / Carriage Assembly as shown in Figure 1
4. Remove the Back Pad mounting screw (Figure 1).
5. Remove the retainer bracket and spring.
6. Remove the Back Pad.
Replacement
1. Position the Back Pad in the Paper Feed / Carriage Assembly.
2. Reinstall the spring; then the mounting bracket.
3. Reinstall the mounting screw.
4. Reinstall the following:
a. Paper Feed / Carriage Assembly (REP 1. 5)
b. Exit Guide (REP 1.4)
c. Top Cover (REP 1.3)
d. Cartridge Cover (REP 1.2)
e. Paper Tray Assembly (REP 1.1)
f. Output Tray (PL 1.1)
g. Printhead (REP 1.0)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 48
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.15 Printhead Ribbon Cable
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank page could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0. Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
e. Paper Feed / Carriage Assembly (REP 1. 5)
3. Remove the belt (PL 2.1) from the carriage motor pulley (right end).
4. Remove the belt from the Encoder pulley (left end).
5. Rotate the carriage shaft cams so that their flats are aligned with the sides of the slot on each side
frame (Figure 1).
NOTE: Expect moderate to heavy resistance when removing carriage from printer side frames.
CAUTION: Ensure no portion of carriage is beneath Ink Level Sensor during carriage removal. During
removal / replacement, it is necessary to simultaneously slide both cams from / to their respective slots. A
ribbon cable is attached to the carriage board. Do not damage the jack or connector lock while removing
carriage (Figure 2).
6. Remove the carriage from the Paper Feed / Carriage Assembly.
7. Remove the carriage shaft from carriage.
8. Position the carriage upside down (Figure 3).
9. Slide the lock to the unlocked position.
10. Disconnect the ribbon cable from the carriage BOARD.
11. Slide the ribbon cable from the carriage cable restraint.
12. Note the installed position of the ribbon cable on the Paper Feed / Carriage Assembly in the area
shown in Figure 4c.
13. Release the cable from the two cable edge restraints.
14. Slide the cable to the left through the 45° slot; then pull the cable upward and out through the slotted
opening.
Replacement
1. Insert the appropriate end of the ribbon cable through the slotted opening in the Paper Feed / Carriage
Assembly approximately three inches (Figure 4a).
2. Gently maneuver the cable to the right through the 45° slot until positioned as shown in Figure 4b.
3. Pull the cable downward through the slotted opening until the 45° fold is positioned as shown in Figure
4c.
4. Lock the cable beneath the cable edge restraints. The printed side of the ribbon cable should be facing
upward.
5. Insert the free end of the cable into the carriage BOARD connector; slide the connector lock to the
locked position. Ensure the cable is below the molded cable restraint (Figure 3).
6. Reinstall the carriage shaft into the carriage.
CAUTION: Ensure the ribbon cable is not twisted after the carriage has been reinstalled in it's normal
operating position.
7. Reinstall the cams on the carriage shaft; reattach carriage to the Paper Feed / Carriage Assembly;
position the cams as shown in Figure 5.
8. Reinstall the Paper Feed / Carriage Assembly (REP 1. 5).
9. Reinstall the Top Cover (REP 1.3).
10. Reinstall the Cartridge Cover (REP 1.2).
11. Reinstall the Paper Tray Assembly (REP 1.1).
12. Reinstall the Output Tray (PL 1.1).
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 49
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
REP 1.16 Ink Level Sensor
Parts List on PL 2. 1
Removal
CAUTION: Store the Printhead in the Storage Box. Leaving the Printhead removed for long periods of
time will cause the ink nozzles to dry out. Image quality problems or a blank page could result. If
necessary, prime the printhead after reinstallation. (REP 1.0)
1. Remove the Printhead (REP 1.0). Store the Printhead in the Storage Box.
WARNING: Switch off the power. Disconnect the power cord at the wall outlet.
2. Remove the following:
a. Paper Output Tray (PL 1.1)
b. Paper Tray Assembly (REP 1.1)
c. Cartridge Cover (REP 1.2)
d. Top Cover (REP 1.3)
3. Disconnect the ribbon cable from the Ink Level Sensor Board (Figure 1).
4. Remove the screw; remove the Ink Level Sensor.
Caution: It is physically possible to cross-connect the Encoder Harness (J4) and the Low-ink Sensor (J2)
on the Relay Board since they use the same type of connector. By doing so, the Main Logic Board may
be damaged.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 50
Service Manual - OKIJET 2020
Chapter 4 Repair / Adjustment Procedures
ADJ 2.0 Printhead Alignment
Purpose
The purpose is to ensure the vertical print alignment is within specification.
Adjustment
1. Print the Bi-Directional Printing Alignment Test Pattern:
NOTE: Before this adjustment can be performed, electrical power must be disconnected from the printer
for at least 10 seconds.
a. Disconnect the power cord from the wall outlet for at least 10 seconds, then reconnect.
b. Load paper into the Paper Tray Assembly.
c. While pressing and holding the Cartridge Change / Clean button, press and release the Power On /
Reset button.
The printer will print the test pattern shown in Figure 1.
d. If the test pattern fails to print, repeat steps a through c.
2. Check for correct vertical alignment of the center grid line set (00). If OK, press the Power On / Reset
button to exit the test. Otherwise, adjust as necessary.
NOTE: Figure 1 shows the test pattern. Each vertical line is formed by three short lines. If the three lines
are properly aligned, perfectly straight lines will be printed. The adjustment moves only the middle line of
the three lines. The adjustment range is-16 to +16.
NOTE: The grid line set numbering on the test pattern is relative to the actual setting (0 to +16). If the
actual setting is 10, then grid line set at 00 equals 10 and grid line set at -1 equals 9, etc. Observe the
Bi-directional Grid Adjust Test Pattern to determine whether the value needs to be increased or
decreased.
3. Change the current value to a setting that will align the three short lines of the center grid line set.
a) Press the Resume / FF button to decrease the current value.
b) Press the Cartridge Change / Clean button to increase the current value.
c) Store the new value by pressing the Power On / Reset button.
4. Press the Power On / Reset button to save the new setting and exit the test.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 51
Service Manual - OKIJET 2020
Chapter 5 Parts List
PL 1.1 Printer Components
Item
#
1
2
3
4
5
6
7
8
9
10
11
OKIDATA PART #
Tracking #
DESCRIPTION
50223101
50222801
53077601
53077501
50115101
-53591201
55069101
-56416001
50517501
50k35130
50k35140
48k56590
48E42860
101k29360
-60K1010
160k31980
-105k16290
19E35780
Tray: Output
Assembly: Paper Tray
Cover: Top
Cover: Cartridge
Panel: Control
Paper Feed / Carriage Assembly
Box: Storage
Controller: Main (Adj 2.1)
Printer Base (Not Spared)
Supply: Power
Pad: Waste Ink
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 52
Service Manual - OKIJET 2020
Chapter 5 Parts List
PL 2.1 Paper Feed / Carriage Assembly Components (Part 1 of 3)
Item #
1
OKIDATA PART #
--
2
50223001
3
-4
-5
50222601
6
-7
-8
50222701
Note: P/O = Part of
Tracking #
-97K25461
--146K00490
--127K22240
DESCRIPTION
Part of Paper Feed / Carriage Assembly (REF: PL1.1
ITEM 6)
Maintenance Station
Belt (P/O Item 1)
Ground Strap (P/O Item 1)
Encoder (ADJ 2.1 2.2)
Encoder Plate (P/O Item 1) (ADJ 2.1 2.2)
Carriage (P/O Item 1) (ADJ 2.1 2.2)
Assembly: Pump
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 53
Service Manual - OKIJET 2020
Chapter 5 Parts List
PL 2.1 Paper Feed / Carriage Assembly Components (Part 2 of 3)
Item # OKIDATA PART #
9
-10
50411301
11
-12
-13
50517401
14
-15
56635701
16
55626201
Note: P/O = Part of
Tracking #
-130k56490
--19E35770
-12E8630
130K58470
DESCRIPTION
Board: Relay (P/O Item 1)
Sensor: Paper Path (SW1)
Back Pad Retainer (P/O Item 1)
Spring (P/O Item 1)
Pad: Back
Paper Feed / Carriage Housing (P/O Item 1)
Cable: Ribbon Printhead
Sensor: Low Ink
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 54
Service Manual - OKIJET 2020
Chapter 5 Parts List
PL 2.1 Paper Feed / Carriage Assembly Components (Part 3 of 3)
Item #
1
OKIDATA PART #
--
Tracking #
--
2
3
4
5
6
7
8
9
50222901
52110101
-52110102
52110001
52110002
52110003
52110004
38K11210
8R7638
-8R7659
8R7660
8R7661
8R7662
8R7663
DESCRIPTION
Part Of Paper Feed / Carriage Assembly (Ref: PL1.1
Item 6)
Assembly: Exit Guide
Printhead: High Capacity (Black)
Paper Feed / Carriage Housing (Part Of Item 1)
Printhead: Color (Consumable)
Ink Cartridge: Black (Consumable)
Ink Cartridge: Cyan (Consumable)
Ink Cartridge: Magenta (Consumable)
Ink Cartridge: Yellow (Consumable)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 55
Service Manual - OKIJET 2020
Chapter 5 Parts List
Part Number Index
OKIDATA
Part
Number
52110101
52110102
52110001
52110002
52110003
52110004
56635701
50517401
50517501
50222901
53077501
53077601
50223101
50222801
53591201
50223001
50115101
56416001
50222701
50411301
55626201
50222601
55069101
53581810
53591201
53592501
Tracking Tracking
Part
Part
Number Number
8R7638
8R7659
8R7660
8R7661
8R7662
8R7663
12E8630
5023BZ9 19E35770
002A
5022BZ3 19E35780
001A
3551BZ9 38K11210
012A
3550BM1 48E42860
048A
3550BM0 48K56590
008A
3390BM3 50K35130
007A
6733BZ9 50K35140
001A
60K1010
97K25461
6871B034 101K29360
5AA
670BX00 105K16290
03A
5859BZ9 127K22240
001A
6871B024 130K56490
6P0
130K58470
6615B000 146K00490
01A
6871B024 160K31980
0P0
Description
PL
LOC.
Comment
Printhead: High Capacity
Black
Printhead: Color
2.2
Ink Cartridge: Black
Ink Cartridge: Cyan
Ink Cartridge: Magenta
Ink Cartridge: Yellow
Ribbon Cable Printhead
Pad: Black
2.2
2.2
2.2
2.2
2.1
2.1
Consumable, Avg.
Life 1,640 pages
Consumable, Avg.
Life 3,000 pages
Consumable
Consumable
Consumable
Consumable
RSPL
RSPL
Pad: Waste Ink
1.1
RSPL
Assembly: Exit Guide
2.2
RSPL
Cover: Cartridge
1.1
RSPL
Cover: Top
1.1
RSPL
Tray: Output
1.1
RSPL
Assembly: Paper Tray
1.1
RSPL
Box: Printhead Storage
Maintenance Station
Panel: Control
1.1
2.1
1.1
RSPL
RSPL
RSPL
Supply: Power
1.1
RSPL
Assembly: Pump
2.1
RSPL
Sensor: Paper Path
2.1
RSPL
Sensor: Low Ink
Assembly: Encoder
2.1
2.1
RSPL
RSPL
Controller: Main
1.1
RSPL
Box: Shipping OKIJET 2020 N/A
Box: Printhead Storage
N/A
Corrugated Packing (Top)
N/A
RSPL
RSPL
RSPL
2.2
53592502
56631801
Corrugated Packing
(Bottom)
Cord: AC 120 V (Bulk)
Whole Unit
62600201
62600202
OKIJET 2020
N/A
OKIJET 2020 (Multi-lingual) N/A
N/A
N/A
Quick Start (English Only)
Quick Start (Spanish)
Quick Start (French)
User's Guide (English)
Registration / QA Card
MSDS Material Sheet
End User License
Agreement
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Documentation
Documentation
Documentation
Documentation
Documentation
Documentation
Documentation
Service Training Kit
N/A
Documentation
Sheet: ID (English Only)
Sheet: Read Me First
(English Only)
Manual: Certification
(English Only)
Manual: Service (English
Only)
Quick Start (English Only)
User's Guide (English Only)
N/A
N/A
Documentation
Documentation
N/A
Documentation
N/A
Documentation
N/A
N/A
Documentation
Documentation
User's Documentation
59274901
59277901
59275901
59275701
Service Documentation
58220301
Includes:
58323401
58323501
59276501
59276601
59274901
59275701
N/A
RSPL
N/A
RSPL
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 56
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Diagnostics
GP 1 Printhead Test
GP 2 Printing with DOS
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 57
Service Manual - OKIJET 2020
Chapter 6 General Procedures
GP 1 Printhead Test
Procedure
1. Print the Test Print:
a. Load paper into the Paper Tray.
b. Press and release the Power On / Reset button to switch the Printer power off.
c. While pressing and holding the Resume / FF button, press and release the Power On / Reset button.
The printer prints the test print shown in Figure 1. When the test print is complete, the printer initializes
and returns to the Ready status.
d. If the test print fails to print, repeat steps a through c.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 58
Service Manual - OKIJET 2020
Chapter 6 General Procedures
GP 2 Printing with DOS
Procedure
DOS mode operation requires the DOS application to send CMYK data to the printer as if it were a HP
550c.
Note: The following procedure is required only if printing in DOS, not in Windows.
Note: You will need to have suitable HP 550c capable printer drivers for their DOS applications.
Note: Please refer to readme.txt in the DOS Panel setup for issues concerning this product.
Your printer comes with an additional utility that has been designed for the DOS user. This utility is called
the DOS Printer Panel. The DOS Printer Panel utility allows you to communicate with the printer directly
from your computer. With this utility, you can do the following:
Review and modify the current printer settings.
Determine printer status and any error conditions.
Note: The following procedure is required only if printing in DOS, not in Windows 1. Please use the
following steps to install your DOS printer panel onto your computer:
1. Start at MS- DOS and insert the DOS diskette supplied with the printer into the A drive.
2. Type 'A: install' and press the Enter key. The installer message is displayed.
Note: If you insert the floppy disk to the B drive, type 'B:install.' Hit any key to display the DOS PRINTER
PANEL Installer menu. The Install Directory menu is displayed. The factory default settings are shown.
Control Panel Installer
Install Directory
C:\ OKIDATA\ InkJet\
Exit
Start Install
Make any necessary changes to the DOS PANEL Installer menu. To change any of this information,
press the up and down arrow keys until the option you want to change is highlighted, then press the Enter
key. Enter your new choice, then press the Enter key to exit the option.
3. If no change is made to the Install menu Press the Enter key to begin installation.
If the Installer menu has been changed, use the TAB key until Start Installation is highlighted. Press
the Enter key to begin installation. The directory of the name specified in the message will be created
and the program on the disk will be copied in the specified directory.
The files will be copied and a message will appear that the installation has been successfully
completed.
4. Press any key to return to the DOS prompt.
Note: The Installation ERROR message will be displayed if an error occurs during the installation. Press
the ESC key to exit installation and return to the DOS prompt. If any other key is pressed, the screen
returns to the Installer menu and the Install Directory will be highlighted. This error message generally
occurs when the program on the floppy disk could not be copied to the specified drive and directory.
Verify the directory name.
Refer to "Setting up the Printer for DOS" section for information on how to set up the printer.
Check if:
directory name is too long --> rename
illegal characters are used --> rename
directory already exists --> rename
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 59
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Product Specifications
Physical Characteristics
Electrical Requirements
Printer Capabilities
Supplemental Items
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 60
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Physical Characteristics
WIDTH
16-3/8" (416 mm)
DEPTH
11-3/4" (299 mm)
HEIGHT
7-5/8" (193 mm)
WEIGHT
10.1 Pounds (4.6 kg)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 61
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Electrical Requirements
107 - 125 VAC (USCO)
220/240 VAC
+/- 10% (RXL)
POWER CONSUMPTION
RUNNING
0.6 amps
POWER SAVER
0.15 amps
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 62
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Capabilities
Table 1.
Type
Print Paper Size
Copy Paper Weights
Paper Tray Capacity
Output Tray Capacity
Throughput
Desktop Ink Jet Printer (Portable)
Minimum 3.9" x 3.9" (100 mm x 100 mm)
Maximum 9' x 14" (229 mm x 356 mm)
2
Paper: 16 to 36 lb. (60 - 135 g/m )
2)
Optimum paper: 20 lb. (75 g/m
2
Envelopes: 20 to 24 lb. (75-90 g/m )
2
Cards: 90 lb. (163 g/m )
2
150 Sheets 20 lb. (75 g/m )
2
50 Sheets 20 lb. (75 g/m )
Black with High Capacity Printhead - 5 ppm
Back with Color Printhead - 4 ppm
Color with Color Printhead - 1 ppm
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 63
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Supplemental Items
Supplies
Printhead High Capacity Black
Printhead: Color
52110101
52110102
Ink Cartridges
Black
Cyan
Magenta
Yellow
Printhead Storage Box
52110001
52110002
52110003
52110004
53591201
Documentation
User's Documentation
Quick Start (English Only)
Quick Start (Spanish)
Quick Start (French)
User's Guide (English Only)
Registration / QA Card
MSDS Material
End User License Agreement
Service Documentation
Service Training Kit
Includes:
Sheet: ID (English Only)
Sheet: Read Me First (English Only)
Manual: Certification (English Only)
Manual: Service (English Only)
Quick Start (English Only)
User's Guide (English Only)
59274901
59277901
59275901
59275701
58220301
58323401
58323501
59276501
59276601
59274901
59275701
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 64
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Overview and Technical Overview Introduction
Printer Overview
This section provides a brief overview of the printer. Also included are the operator activities that will
help you to become familiar with the printer features. This section is divided into the following
categories:
- Printer overview
- Printer operation
- Printer maintenance
Technical Overview
This section provides a brief technical overview of the printer. This section is divided into the following
categories:
- Power and Control
- Printing and priming
- Carriage Drive
- Paper Supply / Paper Feed
- Sensors and Status Indicators
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 65
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Overview
Printer Specifications
Features and Operation
Safety Notes
Printer Installation
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 66
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Specifications
Read the "Specification" information in the User Guide.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 67
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Features and Operation
For detailed description of the following features and operation, refer to the User Guide.
Safety Notes
Printer Installation
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 68
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Safety Notes
Read the "Important Safety Instructions" in the User Guide.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 69
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Installation
Refer to "Set Up" in the User Guide for the following information and activities.
Read the information listed below in the User Guide. If your printer is not installed, perform the steps
indicated.
"Select a Location"
"Unpack"
"Remove the Packing Materials"
If your printer is already installed, familiarize yourself with the following information in the User Guide.
Read "Getting to Know Your Printer". Refer to the illustrations and locate each part on the printer.
Read "Connect to Power". Attach the power cord.
Points to remember:
The power cord must be disconnected from the wall outlet to complete shut off the power to the
printer.
Some or all of the lights on the control panel may come on and go off when you plug in the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 70
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Operation
Read "Install the Printhead and Ink Cartridges", in the "User's Guide".
Install the Ink Cartridges into the Printhead if they are not installed. (If the Ink Cartridges are already
installed, do not remove them). You will practice removing and installing the Printhead later in this
module.
Loading the paper
Test print mode
Connecting the printer to a computer
Control panel
Printing
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 71
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Loading the paper
Read "Load Paper", in the User's Guide.
Load several sheets of paper into the Paper Tray. Be sure that the paper guide is correctly positioned to
match the size of the paper being used.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 72
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Test print mode
Read "Print the Demo Page", in the User's Guide. A host computer is not required to run the demo prints.
A demo print should be run each time the printer is moved or when a Printhead or Ink Cartridge is
replaced.
Read "Print the Demo Page".
Perform the Demo Print test.
Note: The test may be canceled by pressing the Power On / Reset button.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 73
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Connecting the printer to a computer
If a computer is available, "Connecting to the Computer ".
Read "Install the Printer Driver ".
Perform the "Installation on Windows 3.x®" or the "Installation on Windows 95®" printer driver
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 74
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Control panel
Read the following information and locate the buttons and lights on the printer:
Power On / Reset button
Power On LED
Cartridge Change / Clean button
Error LED
Low Ink LED( s)
You will have an opportunity to use these buttons and observe these lights later in this module.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 75
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printing
Read "Checking Printer Settings".
Points to remember:
The Paper Tray may be used for media such as plain paper, paper faced labels, transparencies,
photo glossy, fabric transfer, or envelopes.
Envelopes should not be placed on top of other print media. The envelope guide must be raised to
position the envelopes.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 76
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printer Maintenance
Cleaning
Replacing the Printhead
Troubleshooting
Removal / Replacement of the printer components
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 77
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Cleaning
Briefly familiarize yourself with the "Cleaning the Printer" in the "Maintenance" section of the User Guide.
Points to remember
Printer power should be turned off and the power cord should be unplugged before cleaning the
printer.
Use only water, not detergent or alcohol, to clean the printer. Be sure not to drop water inside the
printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 78
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Replacing the Printhead
Read the "Replacing / Swapping the Printhead" information in the "Maintenance" section of the User
Guide.
Practice removing the Printhead by following the removal steps. Reinstall the Printhead by following the
replacement steps.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 79
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Troubleshooting
Briefly familiarize yourself with the "Troubleshooting" section of the User Guide.
Points to remember:
The user should try all the steps before calling for service. The user should also be prepared to report
a description of the problem accurately when calling for service.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 80
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Removal / Replacement of the printer components
Refer to the "Repair / Adjustment," section in this service manual (Section 4) and perform the following
removal and replacement procedures:
Printhead
Paper Feed / Carriage assembly
Top Cover assembly
To perform the exercises in the next section, Reinstall the Top cover assembly.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 81
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Technical Overview
Power and Control
Printing and Priming
Ink Level Sensing
Carriage Drive
Paper Supply / Paper Feed
Sensors and Status Indicators
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 82
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Power and Control
The power and control functions provide electrical power from the wall receptacle to all the printer
components. These functions also control the operation of all the electrical components during the print
cycle.
This topic is divided into the following sections:
Standby power
Run control
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 83
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Standby power
The purpose of standby power is to provide the printer with AC power and low voltage DC power. Figure
1 shows the standby power components.
When the power cord is plugged into the power receptacle, ACH (AC High) and ACN (AC Neutral) are
sent to the Power Supply. The Power Supply converts the AC voltage to +42 VDC and +5 VDC. The +42
VDC is used by the Main Control Board and the motors in the printer. The +5 VDC is used by the Main
Control Board and other components in the printer.
The Power On/ Reset switch does not remove DC power from the printer. It merely enables and disables
the printer operation.
Figure 1 shows the location of the Power Supply.
Locate the Power Supply in the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 84
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Run control functions
The run control components perform the following principle functions:
Monitor the input signals during standby.
Provide the output signals to switch the printer components on and off at the correct time during the
print cycle.
Monitor the input signals to detect a printer malfunction during the print cycle.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 85
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Main Control Board
The Main Control Board is the principal printer control component. The Main Control Board contains the
control logic, which sends signals that are preprogrammed to synchronize the mechanical drive systems
and the electrical functions that control the printer. Figure 2 shows the location of the Main Control Board.
Locate the Main Control Board in the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 86
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Control Panel Assembly
The Control Panel Assembly on the front of the printer contains the pushbuttons (which allow the user to
operate the printer) and indicators (which show the user the status of the printer).
The Control Panel Assembly, located behind the front of the Top Cover, is connected to the Main Control
Board by a ribbon cable.
When the operator selects a mode, the Control Panel Assembly Board sends a signal to the Main Control
Board. The Main Control Board interprets the signal and provides a signal to switch on the corresponding
LEDs on the console, which indicates the current mode and the printer status.
Locate the Control Panel Assembly Board on the printer.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 87
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Bi-Directional Cable
The Printer is connected to the PC via a parallel cable. If a unidirectional cable is used, only basic Printer
status information is transmitted to the PC. In order to achieve the best results from the printer, a
Bi-directional cable must be used. A Bi-directional cable provides for complete two way communications
between the Printer and the PC. Printer Status (Ready, Not Ready, Printhead and Ink levels) and error
signals are communicated to the PC via the cable.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 88
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printing and Priming
The purpose of the printing subsystem is to supply and deliver ink for the printing process.
This topic is divided into the following sections:
Printing
Print Control
Cleaning and Priming
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 89
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Printing
The Printhead, located on the Carriage, contains the nozzles and the Ink Cartridges. The black Printhead
has a single row of 128 microscopic nozzles. The color Printhead has 120 nozzles, evenly divided for
each of the four colors. Ink is ejected from the nozzles to form an image on the paper. The Printhead, Ink
Cartridges, and the nozzles are shown in
Figure 3.
Note: Be sure not to touch the exposed nozzles.
Locate the following components on your printer:
Printhead
Ink Cartridge(s)
Nozzles
Figure 3. Printhead, Ink Cartridges, and the nozzles
A microheater is located inside each nozzle. Current is applied to the microheater, which heats the ink
inside the nozzle. As the ink heats, a bubble forms, as shown in Figure 4. The pressure from the
expanding bubble ejects the ink from the nozzle. After the ink has been ejected from the nozzle, the
current is turned off. When the ink cools, the bubble
disappears, and the nozzle fills with ink again.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 90
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Print control
The print control logic in the Main Control Board sends the print signals to the Ink Cartridge control logic
in the Ink Cartridge through a ribbon cable. The ink control logic then turns on the microheaters to eject
the ink from the appropriate nozzles. This forms the characters or the graphics as the Carriage scans.
The power and ground signals are also sent to the Ink Cartridge. An enable signal is sent from the
cartridge to inform the Main Control Board that a cartridge is present.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 91
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Cleaning and Priming
The cleaning and priming functions are used to clean the Ink Cartridges and the nozzles in order to
maintain optimum print quality. When the Cartridge Change / Clean button is pressed, the ink that is
clogging the nozzles is ejected and removed by the cleaning components. Also, when an Ink Cartridge is
replaced and the button is pressed, the priming function takes place automatically. The cleaning and
priming components are shown in Figure 5. When the Cartridge Change / Clean button is pressed, the
Carriage and the Printhead move to the right into position for Printhead removal and replacement.
When the button is pressed again, the Carriage and Printhead move to the left into to the parked position.
At the same time the waste ink tube is clamped by the pinch arm on the Maintenance Station and
temporarily restricted. As the paper feed motor rotates, it actuates the pump. The pump action creates a
small vacuum on the blocked tube. This creates suction that pulls ink from the Printhead. The waste ink
tube moves the ink to the waste ink pad located in the printer base.
The pump is actuated whenever the Paper Feed Motor rotates, creating flow from the Printhead to the
pump.
To prevent excessive ink use, the Printhead is moved from the maintenance station whenever the paper
feed motor is on (except during priming).
Ink that remains on the nozzles is removed by the wiper, show in Figure 6.
Locate the following components on your printer:
Maintenance station
Pump
Tubes
Wipers
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 92
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Ink Level Sensing
The Ink Level Sensor measures for a color printhead being present, low, and out of ink conditions. Two
angled reflective surfaces are molded into each cartridge. The Ink Level Sensor contains two emitters (ink
cartridge present and ink level) and a shared detector.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 93
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Ink Cartridge Present
As the carriage is moved, the Ink Level Sensor scans the printheads four color cartridges. The Ink
Sensors ink cartridge present emitter is energized and its beam reflects off both surfaces and returns to
the shared detector (See Figure 7). If an ink cartridge is not present, or is incorrectly installed, no beam
will be reflected and the printer will display a cartridge missing error condition.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 94
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Low Ink Detection
The Ink Level Sensor scans the cartridge ink levels. The sensors level emitter is energized and signals for
each cartridge are checked by the shared detector. Infrared light from the emitter is absorbed by the ink in
the rear reservoir. If the rear reservoir is empty, the reflective surfaces return a low signal. The printer will
display a low ink condition, warning the user that the cartridge will soon be empty. with approximately
10% of the usable ink remaining.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 95
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Out of Ink Detection
As printing continues, after the low ink condition is detected, the number of drops printed is reduced by a
NVM counter. This value is communicated to the printer status display via a bi-directional parallel cable
and is reflected in the ink level "Gas Gauge" on the users PC screen. This low ink counter is reset to full,
when the "not low" to low state change is first detected. Once the counter has reached zero, the printer
status screen will display an out of ink error condition. The user must then replace the empty ink cartridge
to continue printing. After the user performs a Cartridge change in the printer, the cartridge levels are
scanned and the state change is detected by the Ink Level sensor. The state changes from low ink to not
low and resets the counters in NVM and clears the out of ink error.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 96
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Carriage Drive
The purpose of the Carriage subsystem is to position the Printhead for the printing process.
This topic is divided into the following sections:
Carriage drive
Encoder
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 97
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Carriage drive
The Carriage Motor, MOT1, is a stepper motor that is controlled by the Main Control Board.
The motor moves the Carriage from right to left and left to right on the Carriage shaft via the Carriage belt
and pulleys. The pulleys are mounted on the Encoder (discussed later in this module) and the Carriage
Motor. A spring on the Encoder prevents slack in the Carriage belt.
The Carriage Home Sensor detects the Carriage at the home position. The sensor is mounted on the
underside of the Carriage. At power on, or after an error has been cleared, the Carriage moves to the
right, and then to the left. When the Carriage moves to the home position, the Home Sensor detects the
Carriage home plate (which is located on the
Encoder plate) and a home position detection signal is sent to the Main Control Board. The Carriage drive
components are shown in Figure 7.
Locate the following components on the printer:
Carriage
Carriage Home Sensor
Carriage Shaft
Carriage belt and pulleys
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 98
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Carriage movement at power on
The Carriage movement sequence at power on is described below:
1. The Carriage moves to the right to activate the Carriage Home Sensor. This action also wipes the ink
nozzles.
2. The Paper Feed Motor turns on and rotates the cam gear, which moves the bottom of the paper tray
in and out. This prepares the first sheet of paper to feed into the printer.
3. The Carriage moves to the right about three inches. The Carriage stops for approximately one
second. Then the
Carriage increments to the left, where the ink level in the Ink Cartridges is monitored by the Ink Level
Sensor. The Carriage then returns to the home position.
4. A page is printed and ejected into the Paper Output Shelf. When print data is received, the Carriage
moves to the right, the Paper Feed Motor turns on, and the paper is fed to the printing position.
5. The process is repeated for additional pages.
6. When the printing is finished, the Carriage returns to the home position.
Switch off the printer power. Switch on the printer power and observe the Carriage movement described
in steps 1 through 3 above.
Refer to steps 1 through 5 in the "Replacing / Swapping the Printhead" section of the User Guide and
remove the Printhead. (Do not discard the Printhead.) Be careful not to touch the uncovered nozzles or
nozzle area.
Refer to the "Replacing/ Swapping the Printhead" section of the User Guide and reinstall the Printhead.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 99
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Encoder
The Encoder, shown in Figure 8, tracks the Carriage position. The Encoder contains a disk that has 480
radial lines. The disk is mounted on the same shaft as the Encoder pulley that is moved by the Carriage
belt.
(See "Carriage drive" information in this module.) The photosensor detects each radial line and sends a
reference signal to the Main Control Board for each 1/ 600 of an inch of Carriage movement from the
home position. The Main Control Board uses this signal to position the Carriage.
Locate the following components on your printer:
Encoder
Carriage motor
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 100
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Status code
Error Lamp On (steadily) -- The Main Control Board monitors the Encoder signal by comparing the current
Carriage position to the expected Carriage position. If the Carriage is not at the expected position, the
error lamp will illuminate.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 101
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Paper Supply / Paper Feed
The purpose of the paper supply and paper feed subsystem is to store, transport and eject the paper from
the printer.
This Topic is divided into the following sections:
Paper supply
Paper feed
Load/ Eject mechanism
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 102
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Paper supply
For multisheet feeding, paper is supplied to the printer via the Paper Tray. The Paper Tray holds up to
150 sheets of paper. (See Table 1. Printer Capabilities). Paper guides in the Paper Tray are adjusted to
match the size of the paper. Envelopes and cards can be inserted into the Paper Tray for printing by
flipping the envelope guide to match the size
of the envelopes. Extremely thin paper and chemically processed paper (such as thermal paper) should
be avoided as they may result in paper misfeeds.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 103
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Paper feed
The paper feed assembly feeds and ejects the paper. The rotational force of the Paper Feed Motor, MOT
2, drives the loading and paper feed mechanisms for registering, feeding and ejecting the paper. Each of
these functions is controlled independently by changing the direction of the motor rotation.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 104
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Load and eject mechanism
The Paper Feed Motor, MOT 2 (when turning in the clockwise direction) rotates the paper loading gears
and the cam. These gears and cam operate at power up. The cam gear also rotates when paper is
loaded (before it is fed). When the cam rotates, the bottom of the Paper Tray moves in and out to position
the paper stack in the tray. At the same time the Back pad is energized and moves into the path to
prevent more than one sheet of paper being fed at a time. The Back pad is retracted after the lead edge
of the sheet reaches the Paper Path Sensor, SW1.
When the motor rotates in the counterclockwise direction, the paper feed gears, paper feed and exit rolls
turn. Paper is fed by the paper feed roller until it is in position for the Printhead to begin placing ink on the
paper. At the end of the job, the paper is pressed against the exit roller by the starwheels in the exit guide
and is ejected into the paper output shelf. Signals from the Main Control Board control the incremental
movement of the Paper Feed Motor and the Carriage Motor. This control of the Paper Feed Motor and
Carriage Motor allows for precise placement of the ink on the paper.
Locate the following components on your printer:
Paper Feed Motor
Cam
Paper Tray
Run the Demo Print. Observe the operation of the Paper Tray and the Paper Feed mechanism during the
print cycle.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 105
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Sensors and status indicators
Sensors
Status Indicators
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 106
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Sensors
The Paper Path Sensor, SW1, detects the presence of the paper and sends a signal to the Main Control
Board. This signal is used as a reference for the top margin. If the top margin is not detected, no signal is
sent to the Main Control Board. If the top margin is not detected, the error lamp will light, indicating there
is no paper in the Paper Tray. The Paper Path Sensor is shown in Figure 9.
The Cam Sensor, Q1, is located on the cam shaft. The sensor detects the movement of the cam shaft
during the power on cycle and sends a cam sensor signal to the Main Control Board. The Main Control
Board uses this signal to control the Paper Feed Motor during the paper loading cycle. The Cam Sensor
is shown in Figure 9.
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 107
Service Manual - OKIJET 2020
Chapter 6 General Procedures
Status indicators
Error LED on (steady). The error LED comes on when the sensor does not detect the cam rotating (Paper
Feed Motor is not on).
Locate the Paper Path Sensor and the Cam Sensor on the printer:
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 108
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Plug / Jack Location Index
P/J NO.
CN1
CN1
CN2
CN2
CN4
J1
J2
J3
J4
J5
J6
J7
J9
J10
J11
J12
LOCATION
On Main Control Board
On Power Supply
On Main Control Board to Control Panel Board
On Power Supply
On Main Control
On Distribution Board to Main Control Board
On Distribution Board to Low Ink Sensor Q2
On Distribution Board to Paper Path Sensor SW1
On Distribution Board to P/J9
On Distribution Board to Carriage Motor MOT1
On Distribution Board to Paper Feed Motor MOT2
On Distribution Board to Cam Sensor Q1
On Encoder Assembly
On Low Ink Sensor Q2
On Carriage
On Carriage
FIG.
7-3
7-3
7-3
7-3
7-3
7-4
7-4
7-4
7-4
7-4
7-4
7-4
7-4
7-5
7-5
7-5
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 109
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Plug / Jack Location Drawings
Figure 7-1. Main Control Board and Power Supply
Figure 7-2. Carriage Assembly (Bottom View)
Figure 7-3. Carriage
Figure 7-4. Front View
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 110
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Figure 7-1. Main Control Board and Power Supply
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 111
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Figure 7-2. Carriage Assembly (Bottom View)
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 112
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Figure 7-3. Carriage
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 113
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Figure 7-4. Front View
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 114
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Block Schematic Diagrams (BSDs)
Chain 1 AC/DC Power Generation
Chain 2 Selection and Indication
Chain 3 Machine Run Control
Chain 8 Paper Feed
Chain 9 Print Control
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 115
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Chain 1 AC/DC Power Generation
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 116
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Chain 2 Selection and Indication
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 117
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Chain 3 Machine Run Control
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 118
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Chain 8 Paper Feed
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)
Page: 119
Service Manual - OKIJET 2020
Chapter 7 Wiring Data
Chain 9 Print Control
Copyright 1997, Okidata, Division of OKI America, Inc. All rights reserved. See the OKIDATA Business Partner Exchange (BPX) for
any updates to this material. (http://bpx.okidata.com)