NEC 2600, 2610 cellular telephone Owner’s Manual

NEC 2600
Owner’s Manual
NEC 2600/2610 Quick Reference Guide
Battery
The phone battery should
be charged before being
used for the first time.
Turn On Phone
Press and hold the P key
for approximately two
seconds to turn on the
phone.
Turn Off Phone
Press and hold the P key
for approximately two
seconds to turn off the
phone.
Standby Mode
Once the phone is powered
on, the phone enters the
standby mode. The phone
stays in the standby mode
until a call is placed or
received, a menu is
accessed, or the phone is
powered off.
Place a Call
Enter in the telephone
number and press S.
Note that the phone must
have cellular service to
place a call.
Answer a Call
When the phone rings,
press S to answer the
call. Note that the phone
must have cellular service
to receive a call.
End a Call
Press E.
Access and Navigate
Menus
Press M to display the
main menu. Press I to view
the contents of the menus
and submenus. Select a
menu item by pressing
either M when the item is
highlighted or by pressing
the corresponding menu
item number.
Storing a Phone
Number into the
Phone Book
Press M21. Enter the
phone number; press M.
Use the keypad to enter a
name associated with the
phone number; press M.
Press M again to accept
the displayed phone book
location; or enter a specific
location and press M.
Dial a Phone
Number Stored in
the Phone Book
Press B. Use I to locate
the desired phone number
and press S.
Adjust Earpiece
Volume
With a call in progress, press
I to increase or decrease
the earpiece volume.
Adjust Keypad
Volume
With the phone in the
standby mode, press I to
increase or decrease the
keypad volume.
NEC 2600/2610 Quick Reference Guide
Set Ringer Volume
Press M441.
Select one of five settings.
Press E.
Set Ringer Type
Press M442 .
Select one of six settings.
Press E.
Store Voice Mail
Phone Number
You can easily store the
voice mail service phone
number into your phone.
Enter in the voice mail
phone number and press
M34 to store the
number into the phone.
Once the voice mail
number is stored, you can
press and hold 1 to
retrieve messages.
Retrieve Voice Mail
If voice mail service is
available through your
cellular service provider
and the voice mail phone
number is set up in your
phone, press and hold 1
to retrieve your voice mail
messages.
Retrieve Text
Messages
If text messaging service is
available through your
cellular service provider,
press M32 to easily
view your text messages.
Press I to scroll through
each line of the messages.
Press E to exit.
Set Time and Date
Press M461. Enter
in the hour; press N (scroll
key down arrow). Enter in
the minutes; press N. Press
M to select a.m. or p.m.
Enter in the month (1-12);
press N. Enter in the day (131); press N. Enter in the
year; press E.
View Own Number
With the phone in the
standby mode, press C.
Lock/Unlock Keypad
Your phone keypad can be
easily and quickly locked to
prevent inadvertent key
pressing when the phone is
turned on. Press M5 to
lock the keypad; press
M5 again to unlock the
keypad.
Lock/Unlock Phone
Your phone can be locked
to prevent unauthorized
use.
To lock your phone:
Press M0 . As prompted,
enter your 4-digit password.
(The initial password
programmed into your
phone is usually 0000.)
Press 1 to completely
lock your phone or press
2 to partially lock your
phone. Press E.
To unlock your phone:
Press M0 . As prompted,
enter your 4-digit password.
Press 3 to unlock your
phone. Press E.
Table of Contents
Chapter 1: Getting Started. . . . . . . . . . . . . . . . . . . . .1
Phone Activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Phone Safety & Performance . . . . . . . . . . . . . . . . . . . . . . . . 1
NEC Authentic Accessories™ . . . . . . . . . . . . . . . . . . . . . . . . 1
Connecting & Disconnecting the Battery . . . . . . . . . . . . . 1
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
NiMH and Li-Ion Battery Charging Times . . . . . . . . . . . . . 2
Voice Mail Messaging & Text Messaging . . . . . . . . . . . . . 3
Phone Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Phone Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Menu Tree Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Service Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Call & Message Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Menu Navigation Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2: Basic Operations . . . . . . . . . . . . . . . . . . .7
Turning On Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Turning Off Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Battery Charge Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Placing a Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Placing an Emergency Call. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ending a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Answering a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjusting Keypad Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Accessing and Navigating Menus . . . . . . . . . . . . . . . . . . . 10
Setting Ringer Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting Ringer Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Viewing Your Phone Number . . . . . . . . . . . . . . . . . . . . . . . 11
Retrieving Voice Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Retrieving Text Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the Phone Notepad . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . 12
-i-
Table of Contents
Chapter 3: Menus . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Call Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
14
Dialed (Call Log). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Received (Call Log) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Missed (Call Log) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Call Log Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Air Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Clear Call Logs & Air Time Counter . . . . . . . . . . . . . . . . . . 18
2. Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Add to Phone Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
View by Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
View by Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
View by (Phone) Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Locking the Phone Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clearing the Phone Book . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Phone Book Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . 21
3. Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Voice Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Text Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Text Message Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SMS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Clear All Text Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Store As Voice Mail Number . . . . . . . . . . . . . . . . . . . . . . . . 28
4. Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Auto Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Set (Change) Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Any Key Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DTMF Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Transmit DTMF Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Text Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Roll Off Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Word Wrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Sort Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
-ii-
Table of Contents
Ring volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Ring type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Voice Privacy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Select Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Activate Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Network Priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Set Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Set Alarm, Auto On, Auto Off . . . . . . . . . . . . . . . . . . . . . . . 36
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
One-Touch Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Fixed Digit Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Wakeup Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Handsfree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Handsfree Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Auto Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Reset Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
View Own Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5. Lock/Unlock Keypad . . . . . . . . . . . . . . . . . . . . . . 40
6. Silent Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7. Non Public Mode. . . . . . . . . . . . . . . . . . . . . . . . . . 40
Acquire New System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Search for System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
View Stored Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8. Digits Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Manual Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Auto Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Link to Phone Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9. Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Mic Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
All Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Unmute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
0. Phone Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
-iii-
Table of Contents
Chapter 4: Safety & Performance. . . . . . . . . . . . . 46
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Phone Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Battery Care & Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chapter 5: Warranty & Service . . . . . . . . . . . . . . . 58
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
NEC Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
NEC Wireless Marketing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
-iv-
Chapter 1: Getting Started
Phone Activation
Before you can use your new NEC cellular telephone, the
phone must be activated by a cellular service provider.
Please contact your local cellular service provider for any
questions regarding phone activation.
Phone Safety & Performance
Prior to operating your cellular phone, please read this manual thoroughly including “Chapter 4: Safety & Performance”
on page 46.
NEC Authentic Accessories™
NEC recommends using only NEC Authentic Accessories
with your cellular phone to ensure optimum quality performance.
Connecting & Disconnecting the Battery
Your phone is powered by a rechargeable battery. (See “Battery Care & Disposal” on page 57 for important battery
information.) To connect the battery to your phone, place
the grooved end of the battery against the base of the
phone. Lower the battery toward the phone to lock into
place. To remove the battery, check that the phone is turned
off. (Note that failure to power off the phone before removing the battery can possibly result in loss of stored numbers
or messages.) Slide the locking latch located above the battery upward and carefully lift the battery away from the
phone.
Battery
Locking Latch
Battery
-1-
Charging the Battery
A new phone battery must be fully charged before
being used for the first time. The phone battery can be
charged through the setup described and shown below.
The charging times listed below indicate the charging duration with the phone powered off.
Charging Setup: Phone,
Standard or Rapid AC Adapter, &
Charging Stand
Plug the AC adapter into a standard AC electrical outlet. Insert the
adapter plug into the charging
stand jack. Place the phone in the
charging stand. The red LED indicator on the charging stand illuminates while the battery is charging,
and turns off when charging is
complete.
NiMH and Li-Ion
Battery Charging
Times
(in digital mode)
Standard NiMH
Slim Li-Ion
Extended Li-Ion
With Standard Charger With Rapid Charger
~ 4 hours
< 2 hours
N/A
< 2 hours
N/A
< 2 hours
-2-
Voice Mail Messaging & Text Messaging
Voice mail messaging and text messaging services, when
available, are provided by your cellular service provider.
Before you can receive either voice or text messages with
your phone, you must subscribe to these cellular service
provider options. Contact your cellular service provider for
information on availability and setup of these services. See
“Voice Messages” on page 24 and “Text Messages” on
page 25 for information on retrieving messages.
Phone Password
When your phone is activated, a 4-digit password is programmed into the unit. The password locks and unlocks
your phone, and provides access to restricted phone settings. The initial password programmed into the phone is
usually 0000. Check with your cellular service provider for
additional information on your security password.
-3-
PHONE LAYOUT
Antenna
Earpiece
Display Screen
Scroll Key
! ;(
+
1 2: 00am
Jan 01
SERVI CE
Standby Mode
Display Example
Phone Keys
\ ! ;(
+
5551 21 2
I n Use
Microphone
Call in Progress
Display Example
-4-
MENU TREE OVERVIEW
M
Menu Options
1 Call Logs
2 Phone Book
1
2
3
4
5
6
Add to Phone Book
View by Name
View by Location
View by Number
Lock Phone Book
Clear Phone Book
3 Message
4 Settings
1
2
3
4
5
6
7
8
9
0
5 Lock
Keypad
Lock
Call
Text Message
Audio
Network
Clock
Environment
Handsfree„
Reset settings
View Own Number
1
2
3
4
5
1
2
3
4
Dialed
Received
Missed
Air Time
Clear
Voice Messagesz
Text Messagesz
Clear All Text Messages
Store as Voice Mail number
6 Silent Mode
1 Off
2 On
7 Non Pub Mode
Š
1 Acquire New System
Š
2 Search for System
3 View Stored Systems
8 Digits Editing
Š
1 Manual Pause
2 Auto Pause
3 Link to Phone Book
9 Mute (Available only with a call in progress)
0 Phone Lock
Enter
Password
1 Mic Mute
2 All Mute
3 Unmute
1 Full
2 Partial
3 Unlock
z Check with your cellular service provider for availability and service.
„ Only available when phone is used with a handsfree adapter.
 Must have rights to a non-public or private system.
-5-
DISPLAY ICONS
Service Indicators
! or /
Call & Message Indicators
Digital or Analog
Service
\
Call in Progress
<>
Voice Mail Message Received
[]
Text Message
Received
Operation Indicators
+
Battery Charge
Indicator (fully
charged status
shown)
=
Phone Full Lock
Setting Activated
;(
Cellular Signal
Strength
@
Phone Partial
Lock Setting
Activated
~
Battery Charging
in Progress
@
Alarm Clock
Setting Activated
S
Silent Mode
Setting Activated
{||}
In Standby,
Keypad Volume
Adjusted; During
Conversation,
Earpiece
Volume Adjusted
MENU NAVIGATION KEYS
Key
Action
Key
Action
M
Display Main Menu
or select a flashing
menu or submenu
selection.
E
Exit any menu and
return to standby
state display.
I
Scroll to view entire
menu and submenu
contents. Adjust
earpiece and keypad
volume by pressing
top portion of key to
increase or bottom
portion of key to
decrease.
C
Press to return to
next higher menu
level; press and hold
to return to standby
mode display.
-6-
Chapter 2: Basic Operations
Turning On Phone
Press and hold the P key for approximately two seconds
to turn on the phone.
The cellular signal strength indicator, the battery charge
indicator, the time, the date, and the cellular service provider(s) indicator appear on the display. (See “Display Icons”
on page 6.)
The cellular service provider
indication, shown in this
! ;(
+
example as SERVICE,
1 2: 00am
appears on the phone display
Jan 01
as the name of the current serSERVI CE
vice provider when the phone
is operating on a recognized
provider’s system. When the
phone operates on an unrecognizable system, HOME or
ROAM is displayed.
Turning Off Phone
Press and hold the P key for approximately two seconds
to turn off the phone.
Standby Mode
Once the phone is powered on, the phone enters the
standby mode. (The above screen illustration depicts the
phone in standby mode.) The standby mode remains displayed until a call is placed or received, a menu is accessed,
or the phone is powered off. Note that the phone must have
cellular service to either send or receive phone calls.
Signal Strength
The cellular signal is indicated on the display as ;( with the
maximum of six bars indicating a strong signal. Although
you can use the phone without extending the phone
antenna, extending the antenna can increase the strength
of the received cellular signal.
-7-
Battery Charge Indicator
The battery charge indicator (+) shows the charge level of
the battery. When the battery charge drops to a low level,
the phone displays the following warning message:
RECHARGE
BATTERY
While displaying the recharge notification, the phone also
sounds a short tone at ten-second intervals. Once the
recharge message displays and the short tone sounds, the
phone battery has approximately one minute of use
remaining. The phone then automatically powers off. See
“Charging the Battery” on page 2.
Placing a Call
With the phone in the standby mode, key in the telephone
number and press S . The phone icon (\) appears indicating the phone is in use. Note that the phone must have cellular service to either send or receive phone calls.
Correcting Digit Entry Error
If you make a mistake entering a phone number, press
C once to delete the last entered digit, or press and
hold C to erase all of the entered digits.
Dialing a phone number stored in phone book
With the phone in the standby mode, press B to access
the phone book, use the I key to locate the desired
phone number, and press S .
Calling Last Number Dialed
With the phone in the standby mode, press S to call the
last number dialed.
Dialing a phone number on notepad
During a call, you can use your phone as a notepad or
scratchpad to record a phone number provided to you.
Once the call in progress is completed and you press E
to terminate the call, you can dial the displayed notepad
phone number by pressing S. See “Adding Numbers
from Notepad to the Phone Book” on page 20 for storing
the notepad information to your phone book.
-8-
Placing an Emergency Call
With your phone powered on and operating in normal, unrestricted conditions, you can place a call for emergency service (for
example, 911) by entering in the phone number digits and pressing S .
Under certain conditions, such as partial or full phone lock (see “0.
Phone Lock” on page 45), calls can be restricted. To help ensure
that emergency calls can be placed, even under these restricted
conditions, your phone contains a preprogrammed emergency
number. If the emergency number you dial matches the preprogrammed number, the call is placed regardless of any restrictions.
The preprogrammed number is usually 911; however, your service
provider may change the number if necessary. If you are uncertain as to the number that has been preprogrammed, contact
your service provider.
You can also program an emergency number into a speed-dial,
one-touch location (see “One-Touch Dialing” on page 37); however, please note that the one-touch dialing feature does not operate when the phone is set to full lock. If the phone is in full lock, you
must dial the digits of the emergency number.
Ending a Call
Press E . Note that if you are within the menu system (see
“Menu Navigation” on page 13), pressing E once only
exits the menu system; pressing E twice returns the
phone to the standby mode and ends the call.
Answering a Call
When the phone rings, press S to answer the call. Note
that the phone must have cellular service to either send or
receive phone calls.
Caller Identification
If caller identification is available in your area, the phone
number and/or name of the incoming call may be displayed when the call is received. Contact your cellular service provider on the availability of caller identification.
Call Waiting
If call waiting is available in your area, the phone sounds a
tone during a call in progress to indicate a second call is
incoming. To answer the incoming call, press S; press
S again to return to the initial call in progress. Contact
your cellular service provider on the availability of call
waiting.
-9-
Any Key Answer Setting
If the any key answer setting is turned on, any key except
P or E can be pressed to answer an incoming call. See
“Any Key Answer” on page 29.
Ring Alert
The type and volume of the incoming call ringer alert can
be adjusted. See “Selecting Ringer Type” on page 11 and
“Setting Ringer Volume” on page 10.
Adjusting Earpiece Volume
The scroll key can be used to adjust the earpiece volume
during a phone call. With a call in progress, press I to
increase or to decrease the earpiece volume.
Adjusting Keypad Volume
The scroll key can be used to adjust the keypad volume.1
With the phone in the standby state (no call in progress),
press I to increase or to decrease the keypad volume.
Accessing and Navigating Menus
The phone menus can be accessed by pressing the M key.
By pressing M , the Main Menu is displayed. The contents
of menus and submenus can be viewed by pressing I . See
“Chapter 3: Menus” on page 13 for detailed menu navigation information.
Additional Menu Selection
Information
?
For several menu selections, additional
?
usage information is provided to assist
you with making the appropriate selection. These helpful usage tips are identified with the marker shown on the left.
Setting Ringer Volume
The incoming call ringer volume can be set to one of five
settings. Press M441 . The ring volume menu
appears with the currently selected ring volume setting
flashing on the display. The available settings are 1 for minimum, 2 for low, 3 for medium, 4 for maximum, and 5 for
escalating (ringer volume increases as ring alert continues
to sound). Press the corresponding number for the desired
ringer volume setting. The phone rings your selection. Press
E to save your selection and exit the ring volume menu.
1.
When the phone is connected to a handsfree
headset accessory, keypad tones sound through
the headset earpiece.
-10-
Selecting Ringer Type
The incoming call ringer alert can be set to one of several
selections. Press M442. The ring type menu
appears with the currently selected ringer selection flashing
on the display. The available settings are 1, 2, 3, 4, 5, and 6.
Press the appropriate corresponding phone key to hear a
setting. The phone rings your selection. Press E to save
the selected setting and exit the ring type menu.
Viewing Your Phone Number
To view the phone number of your cellular phone, press
C with the phone in the standby mode. The phone number appears on the bottom line of the display for approximately three seconds. (See “View Own Number” on page 39
for another way to view your phone number.)
Retrieving Voice Mail
If voice mail service is available through your cellular provider, you can easily retrieve your voice mail messages by
pressing and holding 1 with the phone in the standby
mode. If the voice mail retrieval phone number has been set
up in your phone, the phone number is automatically
dialed. Follow your cellular service provider instructions for
voice mail retrieval.
Storing Voice Mail Number
See “Store As Voice Mail Number” on page 28.
Retrieving Text Messages
If text messaging service is available through your cellular
provider, you can easily view any text messages received in
your phone by pressing M32 with the phone in the
standby mode. See “Text Messages” on page 25.
Using the Phone Book
Up to 99 phone numbers can be stored in the phone book.
Once phone number entries are stored, the phone book is
at your fingertips for easy dialing. To dial a phone number
stored in the phone book, press B with the phone in the
standby mode to access phone book. Use the I key to
locate the desired phone number and press S . To add,
view, edit, or delete phone book entries, see “2. Phone
Book” on page 18 and “Phone Book Options Menu” on
page 21.
-11-
Using the Phone Notepad
During a phone call, you can use your phone as a notepad
or scratchpad to record a phone number. Once the call in
progress has ended, you can then either dial the phone
number or store the phone number to the phone book.
\ ! ;(
+
0 0m 58 s
I N USE
Call in Progress
+
0 0m 58s
5551 1 1 1 !
I N USE
\ ! ;(
With a call in
progress, press the
number keys to
record a phone
number.
+
;(
0 0m 58 s
5551 1 1 1
After the call in
progress is ended,
the displayed
recorded phone
number can be
dialed or saved to the
phone book.
See “Dialing a phone number on notepad” on page 8 and
“Adding Numbers from Notepad to the Phone Book” on
page 20.
Setting the Time and Date
To access the clock menu for setting the correct time and
date, press M461 . The current time and date settings are displayed. Key in the correct hour; press N (scroll
key down arrow). Key in the correct minutes; press N. Press
M to select either a.m. or p.m. Key in the correct month by
entering in the corresponding number from 1 through 12
for the desired month; press N. Key in the correct day of the
month from 1 through 31; press N. If the correct year is displayed, press E to save the clock entry and to exit the
clock menu.1 If the correct year is not displayed, key in the
corresponding four digits of the correct year, and press E
to save the time and date settings, and to exit the clock
menu.
1.
The year must be entered before the day when
entering the date “February 29” during a leap
year.
-12-
Chapter 3: Menus
Menu Navigation
The phone contains menus and submenus to access and
select the phone settings. (See “Menu Tree Overview” on
page 5.) You can navigate through all menus and submenus
by using the I key to scroll through the menu listings. Each
of the menu and submenu listings has an assigned menu or
submenu number. You can select and access a menu by
pressing the assigned menu number on the keypad or by
pressing M when the desired menu listing is flashing on
the display.
You can return to the previously displayed menu by pressing C . You can return to the standby display by pressing
E or by pressing and holding C .
You can quickly access menus by using the assigned menu
and submenu numbers as shortcuts. Note that the menu
shortcuts are provided for each menu and submenu.
-13-
Main Menu M
The Main Menu contains all of the
menu and submenu settings.
With the phone in the standby
mode, the Main Menu can be
accessed and displayed by pressing M . The Main Menu is displayed on the right.
Press I to scroll
through and view
the entire Main Menu
M ai n m e n u
1 .C al l
L o gs
2 .P h o n e
Bo o k
3 .M e s s age
4 .S e t t i n gs
5 .L o c k
K e y p ad
6 .S i l e n t
Mo d e
7 .N o n P u b
Mo d e
8 .Di gi t s
Ed i t i n g
9 .M u t e
0 .L o c k
Pho n e
Menu Shortcut
1. Call Logs
With the phone in the standby
mode, the Call Log Menu can be
accessed by pressing M1 .
The Call Log Menu is displayed on
the right.
Press I to scroll
through and view
the entire Call Log Menu
-14-
M1
C al l L o g
menu
1 .D i al e d
2 .R e c e i v e d
3 .M i s s e d
4 .A i r T i m e
5 .C l e ar
Menu Shortcut
Dialed (Call Log)
M11
Your phone maintains a list of up to 20 of the last phone
numbers you dialed. To view the list of the last 20 outgoing
calls, press M11 1. Scroll through the contents of the
dialed phone number log by pressing I . Press S to dial a
displayed phone number2 in the log or press E to exit the
dialed phone number log. (See “Call Log Options Menu” on
page 16 for information on dialing, editing, and storing call
log entries.)
Menu Shortcut
Received (Call Log)
M12
Your phone maintains a list of up to 20 of the last incoming
calls you received. To view the list of the last 20 received
calls, press M121. Scroll through the contents of the
received phone number log by pressing I . Press S to dial
a displayed phone number2 in the log or press E to exit
the received phone number log. (See “Call Log Options
Menu” on page 16 for information on dialing, editing, and
storing call log entries.)
Menu Shortcut
Missed (Call Log)
M13
Your phone maintains a list of up to 20 of the last incoming
calls you missed. To view the list of the last 20 unanswered
calls, press M131. Scroll through the contents of the
missed phone number log by pressing I . Press S to dial a
displayed phone number2 in the log or press E to exit the
missed phone number log. (See “Call Log Options Menu” on
page 16 for information on dialing, editing, and storing call
log entries.)
1.
2.
If the dialed, received, or missed phone number log
does not contain any call information, the phone
beeps and the call log menu remains displayed
when an attempt to view the log is made.
When a phone number stored in a call log is viewed,
only the last 10 digits of the phone number are displayed; however, all digits of the phone number (up
to a maximum of 15 digits) are displayed and dialed
when S is pressed.
-15-
Call Log Options Menu
While viewing a call log entry, you can access the call
log options menu by pressing M . The options menu
allows you to dial the phone number in the call log;
edit the phone number and/or identifying name in
the call log; or store the entry to the phone book.
&H@K
'CHS
0TLADQ
'CHS 0@LD
With a call log entry displayed, press
M1 to dial the phone number.
With a call log entry displayed, press
M2 to edit the phone number. With
the last digit of the phone number flashing, press I to move within the displayed phone number. Press C to
delete a flashing digit. Press the number
keys, 1 through 9 and 0 , to insert
digits (up to a maximum of 26 digits).
Once the phone number editing is completed, press M to save the changes
and return to the call log entry with the
corrected phone number displayed; or
press and hold C to exit the call log
options menu without saving the
changes.
With a call log entry displayed, press
M3 to edit the identifying name
associated with the phone number. With
the last letter of the name flashing, press
I to move within the displayed text.
Press C to delete a flashing character.
Using the steps detailed in “Add to
Phone Book” on page 19, enter the
desired letter by repeatedly pressing the
corresponding phone key until the character is displayed. An identifying name
can contain up to a maximum of 20 characters. Once the name editing is completed, press M to save the changes
and return to the call log entry with the
corrected identifying name displayed; or
press and hold C to exit the call log
options menu without saving the
changes.
-16-
Call Log Options Menu (Continued)
2QDODMC
0TLADQ
5SNQD HM
2GNMDANNJ
With a call log entry displayed, press
M4 to edit the prefix of the phone
number. With the initial digit of the
phone number flashing, press I to
move within the displayed phone number. Press C to delete a flashing digit.
Press the number keys, 1 through 9
and 0 , to insert digits. Once the phone
number prefix editing is completed,
press M to save the changes and return
to the call log entry with the corrected
phone number displayed; or press and
hold C to exit the call log options
menu without saving the changes.
With a call log entry displayed, press
M5 to save a phone number to the
phone book. You can edit the number as
detailed in 2. Edit Number, shown above.
Once the editing is complete, press M .
You can then edit the identifying name
as detailed in 3. Edit Name, shown
above. Once the editing is complete,
press M and then one of the following:
•
Press M again to accept the displayed (next available) phone
book location.
OR
•
Type in a specific phone book location and press M. If a specified
phone book location contains a
previously stored phone book
entry, the entry information currently stored in the location flashes
on the display. Press M to overwrite the contents or press I to
scroll through the phone book to
find another phone book location.
Note that during the storing process
steps, you can press and hold C to exit
the call log options menu without saving an entry to the phone book.
-17-
Menu Shortcut
Air Time
M14
Your phone automatically maintains a log of the total air
time usage. The air time counter can be viewed by pressing
M14. The time counter for the air time usage in your
cellular provider service area (indicated with an “H” for
home system) and the air time usage outside your cellular
provider service provider (indicated with an “R” for roam
system) are displayed. Press E to exit the air time log.
Menu Shortcut
Clear Call Logs & Air Time Counter
M15
The phone numbers maintained in the call logs and the air
time usage log can be cleared with all contents completely
erased. To clear one or all of the logs, press M15.
Select 1 to clear the dialed phone number log, 2 to
clear the received phone number log, 3 to clear the
missed phone number log, 4 to clear the air time log, or
5 to clear all of the logs. Press 2 for Yes. Press C or
E to exit the call log clear menu.
Menu Shortcut
2. Phone Book
With the phone in the standby
mode, the Phone Book Menu can
be accessed by pressing M2 .
The Phone Book Menu is displayed on the right.
Press I to scroll
through and view
entire Phone Book Menu
-18-
M2
Ph o n e Bo o k
1 .A d d t o
Pho n e Bo o k
2 .V i e w b y
n am e
3 .V i e w b y
l o c at i o n
4 .V i e w b y
n umber
5 .L o c k
Pho n e Bo o k
6 .C l e ar
Ph o n e Bo o k
Menu Shortcut
Add to Phone Book
M21
To add a phone number to the phone book, press
M21 . Enter the phone number (containing up to a
maximum of 26 digits) you want to add to the phone book
and press M . Use the keypad to enter a name associated
with the phone number. By repeatedly pressing a key, the
characters shown in the table below can be included in a
phone book entry name. You can enter a name of up to 20
characters with any blank space or symbol counted as a
character. Press I to insert a blank space or to advance the
cursor to the next character position when entering a name.
Key
Characters
Key
Characters
1
2
3
4
5
6
1
8 TUV tuv
6 MNO mno
8
9
0
*
#
*
7
7 PQRS pqrs
#
2 ABC abc
3 DEF def
4 GHI ghi
5 JKL jkl
(Press & hold)
(Press & hold)
9 WXYZ wxyz
0&-#.
*
blank spaces
Auto Pause
(indicated by “,”)
Manual Pause
(indicated by “P”)
After the name is entered, press M . Press M again to
accept the displayed (next available) location, or specify
another location and press M. Note that if you enter
another location instead of accepting the displayed next
available location, a phone book entry currently stored in
the specified location could be overwritten and deleted.
Adding Numbers from a Call Log to the Phone Book
If you want to add a phone number from a call log to your
phone book, display the call log entry containing the
desired phone number. Press M to access the call log
options menu. Press 5 to add the number to the phone
book as described in the “Call Log Options Menu” on
page 16.
-19-
Adding Numbers from Notepad to the Phone Book
During a call, you can use your phone as a notepad or
scratchpad to record a phone number. Once the call in
progress is ended, you can either dial the notepad phone
number (see “Dialing a phone number on notepad” on
page 8) or you can store the notepad number to the
phone book. With the notepad phone number displayed,
press M21. As prompted, enter a name and complete the phone book addition following the steps
described in “Add to Phone Book” on page 19.
The phone book entries can be recalled using the name
stored with the phone number, the speed dial location
number, or the phone number itself.
Menu Shortcut
View by Name
M22
To recall a phone book entry by name, press M22.
Enter the first letter(s) of the desired phone book entry
name and press M . If necessary, press the I key to locate
the phone book entry. Press S to dial the phone number
or press E to exit the phone book. (See “Phone Book
Options Menu” on page 21 for information on dialing, editing, and deleting phone book contents.)
Menu Shortcut
View by Location
M23
To recall a phone book entry by the speed dial location
number, press M23. Enter the location number and
press M . Press S to dial the phone number or press E
to exit the phone book menu. (See “Phone Book Options
Menu” on page 21 for information on dialing, editing, and
deleting phone book contents.)
Menu Shortcut
View by (Phone) Number
M24
To recall a phone book entry by the phone number, press
M24. Enter the first number(s) of the desired phone
number and press M . If necessary, press the I key to
locate the phone book entry. Press S to dial the phone
number or press E to exit the phone book. (See “Phone
Book Options Menu” on page 21 for information on dialing,
editing, and deleting phone book contents.)
-20-
Menu Shortcut
Locking the Phone Book
M25
Your phone book can be secured to prevent the contents
from being altered or viewed. Locking your phone book
also safeguards against the contents being accidentally
erased. To restrict access to your phone book, press
M25. As prompted, enter your 4-digit password (see
“Phone Password” on page 3). Press 1 for no restrictions
on your phone book, 2 to restrict the phone book contents to view only, or 3 to completely restrict access to
the phone book. Press E to exit the phone book menu.
Menu Shortcut
Clearing the Phone Book
M26
The phone book contents can be completely erased. To
erase the contents, press M26. As prompted, enter
your 4-digit password (see “Phone Password” on page 3).
Press 2 to clear your phone book. Press C to exit the
phone book menu.
Phone Book Options Menu
While viewing a phone book entry, you can access the
phone book options menu by pressing M. The options
menu allows you to dial the phone book entry; edit the
stored phone number and/or identifying name; or
delete the phone book entry.
&H@K
With a phone book entry displayed, press
M1 to dial the phone number.
-21-
Phone Book Options Menu (Continued)
'CHS
0TLADQ
'CHS
0@LD
With a phone book entry displayed, press
M2 to edit the stored phone number.
With the last digit of the phone number
flashing, press I to move within the displayed phone number. Press C to delete
a flashing digit. Press the number keys, 1
through 9 and 0 , to insert digits (up to
a maximum of 26 digits). Once the phone
number editing is completed, press M to
save the changes and return to the phone
book entry with the corrected phone number displayed; or press and hold C to exit
the phone book options menu without saving the changes.
With a phone book entry displayed, press
M3 to edit the identifying name associated with the phone number. With the last
letter of the name flashing, press I to move
within the text entry. Press C to delete a
flashing character. Using the steps detailed
in “Add to Phone Book” on page 19, enter
the desired letter by repeatedly pressing
the corresponding phone key until the
character is displayed. An identifying name
can contain up to a maximum of 20 characters. Once the name editing is completed,
press M to save the changes and return to
the phone book entry with the corrected
identifying name displayed; or press and
hold C to exit the phone book options
menu without saving the changes.
-22-
Phone Book Options Menu (Continued)
2QDODMC
0TLADQ
&DKDSD
'MSQX
With a phone book entry displayed, press
M4 to edit the prefix of the stored
phone number. With the initial digit of the
phone number flashing, press I to move
within the displayed phone number. Press
C to delete a flashing digit. Press the
number keys, 1 through 9 and 0 , to
insert digits. Once the phone number prefix editing is completed, press M to save
the changes and return to the phone book
entry with the corrected phone number
displayed; or press and hold C to exit the
phone book options menu without saving
the changes.
With a phone book entry displayed, press
M5 to remove the entry from the
phone book. When prompted for confirmation, press 2 to delete entry.
-23-
Menu Shortcut
M3
3. Message
The Message Menu can be
accessed by pressing M3.
The Message Menu is displayed
on the right.
M e s s age
menu
1 .V o i c e
M e s s age s
Press I to scroll
through and view
entire Message Menu
2 .T e x t
M e s s age s
3 .C l e ar
Al l Te x t
M e s s age s
4 .S t o r e as
V o i c e M ai l
number
Your phone can receive voice and text messages. Contact
your cellular service provider for information and availability of voice and text messaging.
Menu Shortcut
Voice Messages
M31
When you receive a voice mail message, the following notification displays:
You
Have
Voice
Mail
To retrieve your voice mail immediately, press S . If your
voice mail number has been stored in your phone (see
“Store As Voice Mail Number” on page 28), the voice mail
system phone number is automatically dialed. Follow your
cellular service provider instructions for accessing your
voice mail and checking your messages.
If you do not wish to retrieve a voice mail message immediately, press C . The voice mail notification is removed from
the display; however, with the phone in the standby state,
the voice mail icon (<>) and the number of voice mail messages appear on the display. If the voice mail phone number
is stored in your phone, you can retrieve messages at any
time by pressing and holding 1 or pressing M31.
-24-
Menu Shortcut
Text Messages
M32
When you receive a text message, your phone sounds an
alert and displays a notification. The alert and the displayed
notification vary depending on the type of received text
message. The types of text messages, the displayed notifications, and the alerts are shown below.
Type of
Text Message
Displayed
Notification
Alert
Emergency
XXX New
EMERGENCY
Messages
Press MENU
Dual tone alert;
repeated three
times.
Urgent
XXX New
URGENT
Messages
Press MENU
Dual tone alert;
repeated two
times.
Normal
XXX New
Messages
Press MENU
to read
Dual tone alert;
repeated one
time.
Bulk
XXX Bulk
Messages
Press MENU
to read
Dual tone alert;
repeated one
time.
XXX in displayed notification equals the actual number
of messages received.
To view your text message(s) immediately, press M . The
first new message is displayed within the text message
viewer. Use I to scroll through each line of the message.
(See “Text Message Viewer” on page 26 for additional information on navigating within text messages.) The end of a
text message is indicated by the following displayed notation:
* * * ** * * * * *
* MSG END *
**********
-25-
The viewing order that text messages are displayed can be
selected. (See “SMS Menu” on page 27 for information on
selecting message sort order.) If the sort order setting is
based on message urgency, message types are displayed in
the following descending order: emergency, urgent, normal, and bulk.
Read and Unread Text Messages
?
?
Note that the sort order applies to
unread and read messages separately.
All unread messages are displayed first
in the appropriate sort order, and then
previously read messages are displayed.
If you do not wish to view a text message immediately,
press C . The text message notification is removed from
the display; however, when the phone is in the standby
mode, the text message icon ([]) and the number of
received unread text messages remain displayed until the
text messages are viewed. You can view text messages at
any time by pressing M32.
Text Message Viewer
Text messages are displayed within the text message
viewer. The following keys can be used to navigate and
operate within the text message viewer.
I
Scrolls up or down through text messages lineby-line.
#
*
S
Scrolls to the top of the next text message.
M
Displays the short messaging service, SMS,
pop-up menu. The SMS menu is detailed on
the following page.
C
Briefly displays the percentage of text message
memory available and the number of unread
and locked messages; then exits the text message viewer.
E
Exits the text message viewer.
Scrolls to the top of the previous text message.
Automatically dials the contact telephone
number if the sender provided a callback telephone number as part of the message.
-26-
SMS Menu
The SMS (short messaging service) Menu within the text
message viewer contains text messaging options such as
locking or unlocking a message, deleting a message, displaying more or less message details, and displaying text
messages based on message urgency or arrival time.
1 .L o ck
With a text message displayed, press M1
M es sa ge to lock a message; the lock indicator (=)
appears on the top line of the text message
indicating the message is locked. Press M1
to unlock the message. Note that a locked message cannot be deleted using the SMS menu
delete message selection; locked messages
can only be deleted through the Message
Menu, M331, “Clear All Text Messages” on page 28.
t
2 . D e l ete
With a text message displayed, press M2;
M es sa ge press 1 to delete.
3 . Disp lay With a text message displayed, press M3 to
m o rem s g display a more detailed message header
d e ta i ls
(includes the time and date the text message is
sent and received); press M3 again to display a less detailed message header (includes
only the time and date the text message is
received).
With a text message displayed:
4 . S or tb y
Press M4 to display the text messages by
m es s a ge message urgency (see page 25 for information
u rg en cy
on message types and sort order).
5 . S or tb y
Press M5 to display the oldest text meso ld es t
sages first.
m es s a ge
6 . S or tb y
Press M6 to display the newest text mesn ew es t
sages first.
m es s a ge
-27-
Menu Shortcut
M33
Clear All Text Messages
Text messages stored in your phone can be deleted. Press
M33. Press 1 to delete all text messages stored in
your phone or press 2 to delete only the unlocked text
messages stored in your phone. Press 2 (for yes) to complete the deletion of text messages. Press C to exit the
clear text messages menu and return to the message menu,
or press E to exit the clear text messages menu and
return to the standby mode.
Menu Shortcut
M34
Store As Voice Mail Number
The voice mail system telephone number can be stored into
your phone. Once the voice mail telephone number is
stored into your phone, voice messages can be easily
retrieved by pressing and holding 1 (or M31). To
store the voice mail telephone number into your phone, key
in the voice mail telephone number with the phone in the
standby mode; press M34. The following message
displays:
Voice
mail
number
has
been
Stored
Press
CLR
Press C to exit the store as voice mail number setting and
return to the message menu, or press E to exit the voice
mail number setting and return to the standby mode.
Menu Shortcut
4. Settings
The Settings Menu can be
accessed by pressing M4.
The Settings Menu is displayed
on the right.
Press I to scroll
through and view
entire Settings Menu
-28-
M4
Se t t i n g
menu
1 .L o c k
2 .C al l
3 .T e x t
M e s s age
4 .A u d i o
5 .N e t w o r k
6 .C l o c k
7 .E n v i r o n ment
8 .H an d F r e e
9 .R e s e t
s e t t i n gs
0 .V i e w o w n
number
Menu Shortcut
Lock
M41
Menu Shortcut
Auto Lock
M411
To protect your phone from unauthorized usage,
you can set your phone to automatically lock
when it is turned on. With the phone in the
standby mode, press M411. As
prompted, enter the 4-digit password (see
“Phone Password” on page 3). Press 2 to set
the automatic lock selection to on.
If automatic lock is set to on, the phone is locked
when it is powered on. To unlock the phone,
press M0 , enter the 4-digit password as
prompted, and press 3 for unlock. Press E to
exit the lock menu. To deactivate the automatic
lock setting, press M411 , enter password, and press 1 . Press E to exit the lock
menu.
Menu Shortcut
Set (Change) Password
M412
The 4-digit password used to access all secured
menu selections and to lock the phone can be
changed. Press M412. As prompted,
enter the current 4-digit password and then
enter the desired new 4-digit password (see
“Phone Password” on page 3). Press M . The
phone automatically resets and powers on
again. The new password must now be entered
to access secured menu settings.
Menu Shortcut
Call
M42
Menu Shortcut
Any Key Answer
M421
With the any key answer setting activated, any
key except E and P can be pressed to
answer the phone. Press M421 . Press
1 to set any key answer to Off or press 2 to
set any key answer to On. When set to On, you
can answer a call with any key except E or P.
-29-
Menu Shortcut
DTMF Length
M422
Your phone can transmit tones, referred to as
DTMF tones, when the keys of the phone are
pressed. These tones allow your phone to successfully communicate with automated telephone services such as banking transactions and
credit card inquiries. You can set your phone to
transmit short tones or long tones. (See the following paragraph for additional information on
short tone use and long tone use). To select the
length of the tone, press M422. Press
1 to select the short tone setting or press 2
to select the long tone setting. Press E to exit
the DTMF length menu.
?
Short Tone Use & Long Tone Use
You can access most automated systems
by setting your phone to the short tone
selection. If you experience any problems communicating with an automated
system, set the DTMF length to long and
verify that the capability to transmit
tones (see the following menu selection,
Transmit DTMF Tone) is turned on. Note
that you must press and hold a key, up
to a maximum of three seconds, to
transmit a long tone. Because transmitting long tones can result in slower dialing, you can set your phone to the short
tone selection and only use the long
tone selection, as needed.
Menu Shortcut
Transmit DTMF Tone
M423
For your phone to successfully transmit tones, as
described above in “DTMF Length”, for accessing
automated telephone systems, the capability to
transmit tones must be turned on. (See the following paragraph for additional information on
setting tones on or off.) To select the DTMF tone
setting, press M423. Press 1 to turn
off tone transmission or press 2 to turn on
tone transmission. Press E to exit the transmit
DTMF tone menu.
-30-
?
DTMF On or Off
Since the ability to communicate with
automated systems is frequently
needed, you can usually set and maintain the DTMF tone transmit selection to
on. If you use the phone scratchpad feature (see “Dialing a phone number on
notepad” on page 8) to key in a phone
number during a call in progress, you
can turn off the DTMF selection, as
needed, to avoid generating audible
tones that can be disruptive during a
phone conversation.
Example of Communicating with An Automated
System Using DTMF Touch Tones
To contact your credit card company for account balance information, you dial the phone number. The credit card automated system
answers by prompting you to enter the account number. If the DTMF
tones selection in your phone is set to on, you can successfully communicate with the automated system. If the DTMF tones selection in
your phone is set to off, then the automated system cannot recognize
any number entries.
C a ll P la ce d to C re d it
C a rd C o m p a n y
E X: {1 80 0 6 37 5 9 17 }
C re d it C a rd C om p a n y
P ro m p t fo r A cco u n t N o .
A c co u n t N u m b e r E n te re d
U sin g P h o ne K e ys
E X: {E nter A ccou n t N u m b e r}
E X: {4 44 4 5 55 5 6 66 6 1 11 1 }
DTMF On:
S y ste m
R e sp o n se
DTMF Off:
N o S ys te m
R e sp o n se
Menu Shortcut
Text Message
M43
Menu Shortcut
Roll Off Order
M431
As described in “Text Messages” on page 25,
your phone can receive text messages if text
messaging service is available through your cellular service provider. When the phone text message storage is full and more text messages are
delivered, existing messages are automatically
replaced with the new messages. The order in
which the existing messages are replaced,
referred to as roll off order, can be selected
based on message arrival time or message
urgency.
-31-
To select the roll off order of messages, press
M431 . Press 1 for existing messages
to be replaced based on time and date of message receipt (oldest messages replaced first) or
press 2 for messages to be replaced based on
message urgency classification (with messages
labeled urgent replaced last). Press E to exit
the roll off order menu.
Menu Shortcut
Word Wrap
M432
The display of words within received text messages can be changed using the word wrap setting. The word wrap setting allows you to
determine how text breaks within received messages. (See the following paragraph for additional information on enabling or disabling word
wrap.) To set the word wrap selection, press
M432; press 1 to enable word wrap or
press 2 to disable word wrap.
?
?
Enabled or Disabled Word Wrap
With the word wrap selection set to
enabled, the word breakage within text
messages is limited to words exceeding
10 characters. Because word division is
restricted, the messages can be easier to
read; however, text messages with word
wrap enabled usually contain more lines
of text and require additional scrolling.
With the word wrap selection set to disabled, text messages are displayed utilizing each of the 10 character blocks
per line. Word breakage is not restricted.
Although word breakage may affect
readability, the messages with word
wrap disabled usually contain less lines
of text and require less scrolling.
Menu Shortcut
Sort Order
M433
The order for viewing incoming messages can be
set using the sort order selection. Press
M433; press 1 to view urgent messages first, 2 to view oldest messages first, or
3 to view new messages first.
-32-
Menu Shortcut
Audio
M44
Menu Shortcut
M441
Ring volume
The ring volume can be set to one of five settings. Press M441 . The ring volume
menu appears with the currently selected ring
volume setting flashing on the display. The available settings are 1 for minimum, 2 for low, 3 for
medium, 4 for maximum, and 5 for escalating
(ringer volume increases as ring alert continues
to sound). Press the corresponding number for
the desired ringer volume setting. The phone
rings your selection. Press E to save your
selection and exit the ring volume menu.
Menu Shortcut
Ring type
M442
The incoming call ringer alert can be set to one
of seven settings. Press M442. The ring
type menu appears with the currently selected
ringer selection flashing on the display. The
available settings are 1, 2, 3, 4, 5, and 6. Press the
appropriate corresponding phone key to hear a
setting. The phone rings your selection. Press
E to save the selected setting and exit the ring
type menu.
Menu Shortcut
Network
M45
Menu Shortcut
Voice Privacy
M451
Voice privacy is an enhanced security feature
available through some digital cellular service
providers. Voice privacy encrypts or scrambles
the voice channel to ensure a telephone conversation is secure and private. For your phone to
utilize the cellular service provider’s enhanced
voice privacy feature, the voice privacy setting in
your phone must be turned on. To set the voice
privacy selection, press M451 . Press 1
-33-
to turn off voice privacy capability and notifications or press 2 to turn on voice privacy capability and notification. When sending a call,
VPActive is displayed if the voice privacy selection is turned on, enhanced voice privacy is
available through the cellular service provider,
and voice privacy security is active for the call in
progress. When sending a call, VPInactive is displayed if the voice privacy selection is turned on;
but voice privacy is not available through the
cellular service provider or voice privacy security
is inactive for the call in progress. Contact your
cellular provider for the availability of voice privacy.
Menu Shortcut
Select Phone Number
M452
Your phone can be programmed with up to two
phone numbers. If two phone numbers are programmed into the phone, you can select the
desired phone number to use by pressing
M452. Press I to highlight the phone
number selection (No.1 or No. 2.). Press E to
exit the select phone number menu.
Menu Shortcut
Activate Network
M453
As described in “7. Non Public Mode” on
page 40, your phone is capable of operating on a
private or residential telephone system in addition to operating on a cellular network system. If
you subscribe to more than one system, you can
turn on or off access to the public, residential, or
private system by pressing M453. As
prompted, enter the 4-digit password (see
“Phone Password” on page 3). Press I to highlight the network activation selection. Press M
or the corresponding number (1, 2, or 3) to
enable or disable access to each system. Press
E to exit. The phone automatically powers off
and then powers on again with the selected network(s) activated. Note that if no selection
changes are made, the phone does not power off
and power on again when E is pressed.
-34-
Menu Shortcut
Network Priority
M454
If you subscribe to more than one system as
described in “Activate Network” on page 34, you
can prioritize access to residential, private, and
public systems by pressing M454. The
systems are displayed in the currently selected
priority order. Press I to highlight the systems
listed in the number two or number three positions. Press M once to move the selected system up one level in priority. Press M again, if
necessary, to move the selected system up to the
number one position. Press E to exit. The
phone automatically powers off and then powers on again with the systems operating in the
specified priority settings.
Menu Shortcut
Clock
M46
Menu Shortcut
Set Clock
M461
The clock can be set with the time, date, and
year. To access the clock menu for setting the
correct time and date, press M461 . The
current time and date settings are displayed. Key
in the correct hour; press N (scroll key down
arrow). Key in the correct minutes; press N. Press
M to select either a.m. or p.m. Key in the correct month by entering in the corresponding
number from 1 through 12 for the desired
month; press N. Key in the correct day of the
month from 1 through 31; press N. If the correct
year is displayed, press E to save the clock
entry and to exit the clock menu. 1 If the correct
year is not displayed, key in the corresponding
four digits of the correct year, and press E to
save the time and date settings, and to exit the
clock menu.
1.
The year must be entered before the day when
entering the date “February 29” during a leap
year.
-35-
Menu Shortcut
Set Alarm, Auto On, Auto Off
M462
Your phone can be used as an alarm clock, and
your phone can be set to automatically turn on
or off at a specified time each day. To access the
alarm or the auto on/off selections, press
M462.
Alarm
Set Alarm: With the Auto On/Auto Off/Alarm setting screen displayed, press I until ALM is flashing;
press M. If the alarm has been previously set, the
last alarm time setting is automatically displayed.
Press I to advance to the hour field. Key in hour;
press I. Key in minutes; press I. Use M to specify a
(for a.m.) or p (for p.m.). Press E to save the alarm
time setting and exit the set alarm menu. The alarm
icon (@) appears on the standby mode display. The
alarm sounds at the specified time setting.
Turn Off Alarming Phone: Press C to turn off the
phone alarm when it sounds.
Deactivate Alarm Prior to Alarming: To turn off
the alarm setting prior to the specified alarm time,
press M462 and press I until ALM is flashing. Press M to cancel alarm time; press C to exit
the set alarm menu.
Auto Power On/Auto Power Off
Set Auto Power On/Auto Power Off: With the
Auto On/Auto Off/Alarm setting screen displayed,
press I until either ON or OFF is flashing; press M.
If the auto power selection has been previously set,
the last auto power setting is automatically displayed. Press I to advance to the hour field. Key in
hour; press I. Key in minutes; press I. Use M to
specify a (for a.m.) or p (for p.m.). Press C to save
the auto power on or auto power off setting and exit
the menu. The phone automatically turns on or
turns off each day at the specified time setting.
Deactivate Auto Power On/Auto Power Off: To
deactivate the auto power on or auto power off setting, press M462, and press I until either
ON or OFF is flashing. Press M to cancel the auto
power on or auto power off time; press C to exit
the menu.
-36-
Menu Shortcut
Environment
M47
Menu Shortcut
One-Touch Dialing
M471
The one-touch dialing feature allows you to
quickly speed dial a phone number by pressing
only one key. With one-touch dialing turned on,
phone numbers stored in phone book locations
1 through 9 can be dialed by pressing and holding the corresponding key on the keypad. To
turn on one-touch dialing, press M471 .
Press 2 to turn on the one-touch dialing selection or press 1 to turn off the one-touch dialing selection. Press E to exit. See “Add to
Phone Book” on page 19 for phone book storing
information.
Menu Shortcut
Fixed Digit Dialing
M472
The type of outgoing calls made from your
phone can be restricted by using fixed digit dialing. For example, the fixed digit dialing selection
can be set to 7 digits to restrict the outgoing
calls to local phone numbers. To set the fixed
digit dialing selection, press M472. As
prompted on the display, enter the 4-digit password (see “Phone Password” on page 3). Type in
a specified number of digits for restricting outgoing calls; for example, press 7 to restrict
outgoing calls to 7-digit numbers. The range is 0
to 26 digits. Press M to save setting; press E
to exit the fixed digit dialing menu. If a call is
attempted to a phone number exceeding the
restricted fixed digit setting, the following message is displayed:
Extra
Dig
Dialed
-37-
Press
CLR
Menu Shortcut
Language
M473
The phone display language can be set to
English, Spanish, French, or Portuguese. To
change the display language selection, press
M473. Press 1 to select English, 2
to select Spanish, 3 to select French, or 4 to
select Portuguese. Press M . The phone automatically powers off and then powers on again
in the selected display language. Note that you
can exit the language menu without making any
changes by pressing C .
Menu Shortcut
Wakeup Message
M474
A personal message, referred to as a wakeup
message, can be stored and displayed briefly
each time your phone is turned on. To store a
wakeup message, press M474. Using the
table under “Add to Phone Book” on page 19,
type in the message by pressing the phone keys.
Press M to save the message and exit the
wakeup message menu.
Menu Shortcut
Handsfree
M48
The following menu selections - handsfree switch, backlight, and automatic answer - can only be activated when
the phone is used with a handsfree adapter.
Menu Shortcut
Handsfree Switch
M481
When your phone is connected to an in-vehicle
handsfree adapter, two phone features are available for some vehicle installation configurations.
If available, the features can be activated by
pressing M481 . Press 2 to enable call
alert, 3 to enable radio mute, or 1 to disable
the call alert or radio mute feature. Press E to
exit the handsfree switch menu.
-38-
Menu Shortcut
Backlight
M482
When your phone is connected to an in-vehicle
handsfree adapter, the keypad and display backlight can be set to remain illuminated continuously. To select the backlight setting, press
M482. Press 2 for the phone backlight
to remain on continuously in a handsfree configuration or press 1 to turn it off. Press E to
exit the backlight menu.
Menu Shortcut
Auto Answer
M483
When your phone is connected to an in-vehicle
handsfree adapter, the phone can be set for
automatic answering of incoming calls. To activate the automatic answer setting, press
M483. Press 2 to turn on automatic
answering or press 1 to turn off automatic
answering. Press E to exit the auto answer
menu.
Menu Shortcut
Reset Settings
M49
The current phone selections can be cleared and reset to
the factory default settings. To reset the phone settings,
press M49. As prompted, enter the 4-digit password
(see “Phone Password” on page 3). Press 2 to reset all
selections to the default settings or press 1 to maintain
the current settings. Press E to exit the reset settings
menu.
Menu Shortcut
View Own Number
M40
In addition to viewing the phone number of your cellular
phone by pressing C (see “Viewing Your Phone Number”
on page 11), you can also display your phone number by
pressing M40 . The phone number remains displayed until E is pressed to exit the view own number
menu.
-39-
5. Lock/Unlock Keypad
Menu Shortcut
M5
Your phone keypad can be easily and quickly locked to prevent inadvertent key pressing when the phone is turned on.
Press M5 to lock keypad; press M5 again to unlock
keypad. If a key is pressed when the keypad is locked, the
following message is displayed:
Keypad
is
locked.
Use
MENU
5
to
Unlock
Note that even with the keypad locked, you can still dial a
preprogrammed emergency number (for example, 911) and
press S to call for emergency services.
Menu Shortcut
6. Silent Mode
The Silent Mode Menu can be
accessed by pressing M6.
The Silent Mode Menu is displayed on the right.
M6
Si l e n t
mode
1 .O f f
2 .O n
By setting the phone to the silent mode, audible phone
alerts are turned off; an incoming call is indicated only by
the backlight flashing and the incoming call notification
appearing on the display. With the silent mode menu displayed, press 1 to turn off silent mode or press 2 to
turn on silent mode. Press E to exit the silent mode
menu. When the silent mode is turned on, the silent mode
icon (S) appears on the standby mode display. Note that
once the phone is turned off, the silent mode selection
automatically resets to off.
Menu Shortcut
7. Non Public Mode
The Non-Public Mode Menu can
be accessed by pressing M7.
The menu is displayed on the
right.
Press I to scroll
through and view
entire Private Mode Menu
-40-
M7
P r i v at e
Mo d e Me n u
1 .A c q u i r e
Ne w Sy s t e m
2 .S e ar c h
fo r Sy s t e m
3 .V i e w
St o r e d
Sy s t e m s
In addition to operating on a cellular network system, your
phone is also capable of operating on a non-public or private telephone system. Note that the phone user must first
subscribe or have rights to a non-public or private telephone system to utilize the following private mode menu
selections - Acquire New System, Search for System, and
View Stored Systems.
Menu Shortcut
M71
Acquire New System
The phone automatically searches or scans for the first available private network system by pressing M71 . The
following message is displayed:
Search
in
progress..
If a system is located, the phone returns to the standby state
with the private system’s descriptive name or label displayed. The private system is now available for use and is
stored into the phone system database. If a system is not
located, the following message is displayed:
No
Systems
Found
Press C to exit the acquire new system selection.
Menu Shortcut
Search for System
M72
You can set your phone to manually search for available private network systems by pressing M72. The following message is displayed:
Search
in
progress..
If systems are located, the phone displays a list of the available systems. Use I to scroll through the list; press E to
save the selected system. The phone returns to the standby
mode with the private system’s descriptive name or label
displayed. The private system is now available for use and is
stored in the phone system database. If no systems are
located, the following message is displayed:
No
Systems
Found
Press C to exit the search for system selection.
-41-
Menu Shortcut
View Stored Systems
M73
System information of each located private system is stored
in the phone system database. The contents of the database
can be viewed by pressing M73. A list of the systems
is displayed. Use I to scroll through the list; press E to
exit the database. If there is no information stored in the
database, the following message is displayed:
D a t a B a se E m p t y Pr es s C L R
Press C to exit the view stored systems selection.
Menu Shortcut
8. Digits Editing
The Digits Editing Menu can be
accessed by pressing M 8.
The Digits Editing Menu is displayed on the right.
Press I to scroll
through and view
entire Digits Editing Menu
M8
Di gi t s
edi ti ng
1 .Man u al
Pau se
2.Au t o
Pau se
3.Li n k t o
Phon e b ook
Automated telephone systems prompt you through a
recorded message to enter a set or sets of identifying numbers such as a credit card account number, bank account
number, or personal identification number. You can use
your phone to easily dial or store multiple sets of numbers,
for accessing automated systems, by separating the sets of
digits with indicators referred to as pause marks. Pause
marks alert your phone to wait or pause before sending the
remaining sets of digits. There are two types of pause marks:
manual and automatic. The two types are described below.
-42-
Menu Shortcut
Manual Pause
M81
When entering the digits of an automated system telephone number and any additional strings of numbers
needed to communicate with the system, you can insert
manual pauses between the sets of digits. To enter manual
pause marks, enter in the telephone number; press
M81 . A “P” is displayed after the phone number.
Enter in the next set of digits. If necessary, press M81
to insert another manual pause and then enter in the next
set of digits. When the automated system telephone number is dialed, your phone waits to transmit the sets of numbers following a manual pause mark. The following
message is displayed:
Press
SND
For
Manual
Pause
Dial
As prompted by the automated system, press S to send
the next set of digits. Continue to press S to send any
remaining sets of digits.
Menu Shortcut
Auto Pause
M82
An automatic pause can be inserted between sets of digits
in a similar manner as manual pauses. To enter automatic
pause marks, enter in the telephone number; press
M82. A “,” (comma) is displayed after the phone
number. Enter in the next set of digits. If necessary, press
M82 to insert another automatic pause and then
enter in the next set of digits. When the automated system
telephone number is dialed, your phone waits approximately three seconds at each automatic pause mark and
then automatically transmits the remaining sets of digits.
Menu Shortcut
Link to Phone Book
M83
If the total number of digits needed to access an automated
telephone system exceeds the maximum 26 digits that can
be transmitted at one time (or stored in each phone book
location), the phone number can be entered and then
linked to a phone book location containing the remaining
strings of numbers. To link a phone number to a phone
book record location, key in the phone number and press
M83; an “L” is displayed. Enter the phone book loca-
-43-
tion (1-99) containing the applicable information. Press S
to dial the phone number. After the phone number is dialed,
the following message is displayed indicating that the
remaining sets of digits must be sent manually be pressing
S.
Press
SND
For
Manual
Pause
Dial
Menu Shortcut
M9
9. Mute
The Mute Menu can be accessed
by pressing M 9 during a
conversation. The Mute Menu is
displayed on the right.
Se t m u t e
1 .M i c M u t e
2 .A l l M u t e
3 .U n m u t e
Menu Shortcut
Mic Mute
M91
The phone microphone can be turned off or muted during a
conversation. With a call in progress, press M91.
Press M93 to turn on the microphone again.
Menu Shortcut
All Mute
M92
The phone microphone and earpiece can be turned off or
muted during a conversation. With a call in progress, press
M92. Press M93 to turn on the microphone
and earpiece again.
Menu Shortcut
Unmute
M93
The microphone mute and full mute settings can be cancelled by pressing M93.
-44-
Menu Shortcut
0. Phone Lock
Your phone can be locked to prevent unauthorized use. To lock
your phone, press M0 . As
prompted, enter your 4-digit
password (see “Phone Password”
on page 3). The Phone Lock
menu is displayed on the right.
M0
Ph o n e Lo c k
1 .F u l l
2 .P ar t i al
3 .U n l o c k
Press 1 to completely lock your phone and restrict the
ability to place calls; only calls to the preprogrammed emergency number (for example, 911) can be dialed. Press E
to exit the lock menu. When the phone is set to full lock, the
full lock icon (=) is displayed.
Press 2 to partially lock your phone and limit the ability to
place calls; only calls to the preprogrammed emergency
number (for example, 911) and the one-touch, speed-dial
phone numbers stored in phone book locations 1-9 can be
placed. (Note that the one-touch dialing selection must be
turned on to speed dial phone numbers; see “One-Touch
Dialing” on page 37 for information on activating one-touch
dialing.) With the phone set to partial lock, text messages
can also be received and viewed; however, callback phone
numbers provided in text messages cannot be dialed. Press
E to exit the lock menu. When the phone is set to partial
lock, the partial lock icon (@) is displayed.
To unlock the phone, press M0 . As prompted, enter
your 4-digit password. Press 3 to unlock your phone;
press E to exit the lock menu. If the phone is unlocked,
neither the full lock icon (=) nor the partial lock icon (@) is
displayed.
-45-
Chapter 4: Safety & Performance
Safety Precautions
For safe and efficient operation of the phone, observe
the following guidelines.
The cellular telephone is a radio transmitter and receiver.
When the unit is powered on, the phone receives and sends
radio frequency (RF) energy. The phone operates in the cellular frequency range of 824 MHz to 894 MHz and the personal communication system (PCS) range of 1850 MHz to
1990 MHz, and employs commonly used frequency modulation (FM) techniques. When the phone is in use, the cellular system handling the call controls the power level at
which the phone transmits. The power level can range from
0.006 watt to 0.6 watt.
Exposure to Radio Frequency Energy
In 1991, the Institute of Electrical and Electronics Engineers
(IEEE) and in 1992, the American National Standards Institute (ANSI) adopted a standard for safe levels of human
exposure to RF energy. Approximately 120 scientists, engineers, and physicians from universities, government, and
industry developed the standard. In March 1993, the Federal Communications Commission (FCC) proposed the
adoption of the standard. The design of your phone complies with the updated standard. RF exposure can be further
limited by controlling the duration of calls and operating
the phone in a power efficient manner.
Efficient Phone Operation
Extend the antenna fully to operate at the lowest power
level possible. Calls can be sent and received with the
antenna retracted; however, the phone operates more efficiently with the antenna fully extended. Hold the cellular
phone in the same manner as a standard telephone is held.
While speaking directly into the mouthpiece, position the
antenna up and over your shoulder. Do not hold the
antenna when the phone is in use. Holding the antenna
affects call quality and may cause the phone to operate at a
higher power level than is necessary.
-46-
Antenna Care and Replacement
Do not use a phone with a damaged antenna. If a damaged
antenna comes into contact with skin, a minor burn could
result. Replace a damaged antenna immediately with a
manufacturer-approved antenna. Use only an NEC supplied
or approved antenna. Unauthorized antennas, modifications, or attachments could damage the phone and could
violate FCC regulations.
Driving
When using your phone while driving a vehicle, remember
that driving is your first responsibility; give full attention to
driving. Obey the area laws and regulations on the use of
cellular telephones while driving. Pull off the road and park
before making or answering a call if driving conditions
require additional caution. Practice good common sense
and utilize the following driver safety tips.
Driver Safety Tips
•
Acquaint yourself with phone features, such as speed
dialing and redial, that help you place a call without
taking your attention off the road.
•
Whenever possible, use a handsfree accessory with
your phone.
•
Place your phone within easy reach of the driver’s seat
to ensure that you can access your phone without
removing your eyes from the road.
•
Inform the person at the other end of the conversation
that you are driving. If necessary, end the call while
driving in heavy traffic or hazardous weather conditions. If you receive an incoming call at an inconvenient time, do not answer the phone. Your voice mail
service, if available, can answer the call.
•
Do not look up phone numbers or take notes while
driving.
•
Assess the traffic before placing calls. If possible, place
calls when your car is stationary.
•
Do not engage in stressful or emotional conversations
that may distract your attention from driving.
•
Use your phone to call for emergency assistance for
yourself and others. Dial 9-1-1 (or the local emergency
number) to report fires, traffic accidents, medical
emergencies, crimes in progress, or any other serious
emergency where lives are in danger.
•
Call roadside assistance or a special non-emergency
assistance telephone number, as necessary, to report
non-emergency incidents.
-47-
Air Bags
An air bag inflates with incredible force. Do not place
objects, including installed and portable wireless equipment, in the area of the air bag or in deployment area of the
air bag. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Electronic Devices
Most modern electronic equipment is shielded from RF
energy; however, RF energy from cellular telephones may
affect some inadequately shielded electronic equipment. RF
energy may affect improperly installed or inadequately
shielded electronic operating and entertainment systems in
motor vehicles. Check with manufacturers or manufacturers
representatives to determine if systems are adequately
shielded from external RF energy. Consult the manufacturer
of any personal medical devices (for example, pacemakers
and hearing aids) to determine if the devices are adequately
shielded from external RF energy. Turn off the phone in
health care facilities when any regulations posted in the
area forbid use of electronic devices. Hospitals or health
care facilities may be using equipment sensitive to external
RF energy.
Pacemakers
Research sponsored by Wireless Technology Research
(WTR) indicates that some wireless telephones cause interference with pacemakers. NEC America, Inc., endorses the
following recommendations:
•
Wireless phones should be kept at a safe distance from
a pacemaker. Existing data indicate that the greater
the distance between a pacemaker and a wireless
phone, the less the risk of interference. The data further indicates that six inches is the proper separation
distance for minimal risk.
•
Practical steps to achieve the recommended separation distance include not placing a wireless telephone
in the area over the pacemaker, such as a shirt pocket,
when the phone is powered on. (The unit is considered on when power is being supplied to the phone by
the battery.) Another practical step is to listen into the
phone using the ear opposite the location of the pacemaker.
•
Note that no comprehensive data indicates that
bystanders with pacemakers are at risk of interference
from another person operating a cellular phone.
-48-
Aircraft
•
Turn off the phone before boarding any aircraft.
•
While the plane is on the ground, receive approval
from the airline crew prior to using the cellular phone.
•
Do not use the phone while the plane is in the air.
To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require airline crew permission prior to phone usage. To prevent
interference with cellular systems, FCC regulations prohibit
using the phone while an aircraft is in the air.
Children
Do not allow children to play with the phone; the phone is
not a toy. Children could hurt themselves or others. In addition, children could damage the phone or make calls that
result in an increase to the phone bill.
Blasting Areas
To avoid interfering in construction projects, turn off the
phone when in a blasting area or in areas posted: “Turn Off
Two-Way Radio.” Construction crews often use remote control RF devices to set off explosives.
Potentially Explosive Atmospheres
Turn off the phone in an area with a potentially explosive
atmosphere. Although it is rare, the phone or its accessories
could generate sparks. Sparks in certain areas could cause
an explosion of fire resulting in bodily injury or even death.
Areas with a potentially explosive atmosphere are usually,
but not always, clearly marked. Potentially explosive areas
include fueling areas such as gas stations, below deck on
boats, and fuel or chemical transfer and storage facilities.
Additional areas are atmospheres with chemicals or particles in the air such as grain, dust, or metal powders; and any
area where it is advised to turn off the vehicle engine.
Do not transport or store flammable gas, liquids, or explosives in the same compartment that contains the phone or
its accessories.
Vehicles using liquefied petroleum gas, such as propane or
butane, must comply with the National Fire Protection Standard (NFPA-58). For a copy of the standard, contact the
National Fire Protection Association, One Batterymarch
Park, Quincy, MA 02269, Attn: Publication Sales Division.
-49-
The U.S. Food and Drug
Administration’s Center for
Devices and Radiological Health
Consumer Update on Mobile Phones
FDA has been receiving inquiries about the safety of mobile
phones, including cellular phones and PCS phones. The following summarizes what is known--and what remains
unknown--about whether these products can pose a hazard
to health, and what can be done to minimize any potential
risk.
Why the concern?
Mobile phones emit low levels of radiofrequency energy
(i.e., radiofrequency radiation) in the microwave range while
being used. They also emit very low levels of radiofrequency
energy (RF), considered non-significant, when in the standby mode. It is well known that high levels of RF can produce
biological damage through heating effects (this is how your
microwave oven is able to cook food). However, it is not
known whether, to what extent, or through what mechanism, lower levels of RF might cause adverse health effects
as well. Although some research has been done to address
these questions, no clear picture of the biological effects of
this type of radiation has emerged to date. Thus, the available science does not allow us to conclude that mobile
phones are absolutely safe, or that they are unsafe. However, the available scientific evidence does not demonstrate
any adverse health effects associated with the use of mobile
phones.
What kinds of phones are in question?
Questions have been raised about hand-held mobile
phones, the kind that have a built-in antenna that is positioned close to the user's head during normal telephone
conversation. These types of mobile phones are of concern
because of the short distance between the phone's
antenna--the primary source of the RF--and the person's
head. The exposure to RF from mobile phones in which the
antenna is located at greater distances from the user (on the
outside of a car, for example) is drastically lower than that
from hand-held phones, because a person's RF exposure
-50-
decreases rapidly with distance from the source. The safety
of so-called "cordless phones," which have a base unit connected to the telephone wiring in a house and which operate at far lower power levels and frequencies, has not been
questioned.
How much evidence is there that hand-held mobile
phones might be harmful?
Briefly, there is not enough evidence to know for sure, either
way; however, research efforts are on-going. The existing
scientific evidence is conflicting and many of the studies
that have been done to date have suffered from flaws in
their research methods. Animal experiments investigating
the effects of RF exposures characteristic of mobile phones
have yielded conflicting results. A few animal studies, however, have suggested that low levels of RF could accelerate
the development of cancer in laboratory animals. In one
study, mice genetically altered to be predisposed to developing one type of cancer developed more than
twice as many such cancers when they were exposed to RF
energy compared to controls. There is much uncertainty
among scientists about whether results obtained from animal studies apply to the use of mobile phones. First, it is
uncertain how to apply the results obtained in rats and mice
to humans. Second, many of the studies that showed
increased tumor development used animals that had
already been treated with cancer-causing chemicals, and
other studies exposed the animals to the RF virtually
continuously--up to 22 hours per day.
For the past five years in the United States, the mobile
phone industry has supported research into the safety of
mobile phones. This research has resulted in two findings in
particular that merit additional study:
1.
In a hospital-based, case-control study, researchers looked for
an association between mobile phone use and either glioma (a
type of brain cancer) or acoustic neuroma (a benign tumor of
the nerve sheath). No statistically significant association was
found between mobile phone use and acoustic neuroma. There
was also no association between mobile phone use and gliomas when all types of types of gliomas were considered
together. It should be noted that the average length of mobile
phone exposure in this study was less than three years.
-51-
When 20 types of glioma were considered separately, however,
an association was found between mobile phone use and one
rare type of glioma, neuroepithelliomatous tumors. It is possible with multiple comparisons of the same sample that this
association occurred by chance. Moreover, the risk did not
increase with how often the mobile phone was used, or the
length of the calls. In fact, the risk actually decreased with
cumulative hours of mobile phone use. Most cancer causing
agents increase risk with increased exposure. An ongoing study
of brain cancers by the National Cancer Institute is expected to
bear on the accuracy and repeatability of these results.1
2.
Researchers conducted a large battery of laboratory tests to
assess the effects of exposure to mobile phone RF on genetic
material. These included tests for several kinds of abnormalities,
including mutations, chromosomal aberrations, DNA strand
breaks, and structural changes in the genetic material of blood
cells called lymphocytes. None of the tests showed any effect of
the RF except for the micronucleus assay, which detects structural effects on the genetic material. The cells in this assay
showed changes after exposure to simulated cell phone radiation, but only after 24 hours of exposure. It is possible that
exposing the test cells to radiation for this long resulted in heating. Since this assay is known to be sensitive to heating, heat
alone could have caused the abnormalities to occur. The data
already in the literature on the response of the micronucleus
assay to RF are conflicting. Thus, follow-up research is necessary.2
FDA is currently working with government, industry, and
academic groups to ensure the proper follow-up to these
industry-funded research findings. Collaboration with the
Cellular Telecommunications Industry Association (CTIA) in
particular is expected to lead to FDA providing research recommendations and scientific oversight of new CTIA-funded
research based on such recommendations.
1.
2.
Muscat et al. Epidemiological Study of Cellular
Telephone Use and Malignant Brain Tumors.
In: State of the Science Symposium;1999 June
20; Long Beach, California.
Tice et al. Tests of mobile phone signals for
activity in genotoxicity and other laboratory
assays. In: Annual Meeting of the
Environmental Mutagen Society; March 29,
1999, Washington, D.C.; and personal
communication, unpublished results.
-52-
Two other studies of interest have been reported recently in
the literature:
1.
Two groups of 18 people were exposed to simulated mobile
phone signals under laboratory conditions while they performed cognitive function tests. There were no changes in the
subjects' ability to recall words, numbers, or pictures, or in their
spatial memory, but they were able to make choices more
quickly in one visual test when they were exposed to simulated
mobile phone signals. This was the only change noted among
more than 20 variables compared.1
2.
In a study of 209 brain tumor cases and 425 matched controls,
there was no increased risk of brain tumors associated with
mobile phone use. When tumors did exist in certain locations,
however, they were more likely to be on the side of the head
where the mobile phone was used. Because this occurred in
only a small number of cases, the increased likelihood was too
small to be statistically significant.2
In summary, we do not have enough information at this
point to assure the public that there are, or are not, any low
incident health problems associated with use of mobile
phones. FDA continues to work with all parties, including
other federal agencies and industry, to assure that research
is undertaken to provide the necessary answers to the outstanding questions about the safety of mobile phones.
What is known about cases of human cancer that have
been reported in users of hand-held mobile phones?
Some people who have used mobile phones have been
diagnosed with brain cancer. But it is important to understand that this type of cancer also occurs among people
who have not used mobile phones. In fact, brain cancer
occurs in the U.S. population at a rate of about 6 new cases
per 100,000 people each year. At that rate, assuming 80 million users of mobile phones (a number increasing at a rate
1.
2.
Preece, AW, Iwi, G, Davies-Smith, A, Wesnes,
K, Butler, S, Lim, E, and Varey, A. Effect of a
915-MHz simulated mobile phone signal on
cognitive function in man. Int. J. Radiat. Biol.,
April 8, 1999.
Hardell, L, Nasman, A, Pahlson, A, Hallquist, A
and Mild, KH. Use of cellular telephones and
the risk for brain tumors: a case-control study.
Int. J. Oncol., 15: 113-116, 1999.
-53-
of about 1 million per month), about 4800 cases of brain
cancer would be expected each year among those 80 million people, whether or not they used their phones. Thus it
is not possible to tell whether any individual's cancer arose
because of the phone, or whether it would have happened
anyway. A key question is whether the risk of getting a particular form of cancer is greater among people who use
mobile phones than among the rest of the population. One
way to answer that question is to compare the usage of
mobile phones among people with brain cancer with the
use of mobile phones among appropriately matched people without brain cancer. This is called a case-control study.
The current case-control study of brain cancers by the
National Cancer Institute, as well as the follow-up research
to be sponsored by industry, will begin to generate this type
of information.
What is FDA's role concerning the safety of mobile
phones?
Under the law, FDA does not review the safety of radiationemitting consumer products such as mobile phones before
marketing, as it does with new drugs or medical devices.
However, the agency has authority to take action if mobile
phones are shown to emit radiation at a level that is hazardous to the user. In such a case, FDA could require the manufacturers of mobile phones to notify users of the health
hazard and to repair, replace or recall the phones so that the
hazard no longer exists.
Although the existing scientific data do not justify FDA regulatory actions at this time, FDA has urged the mobile
phone industry to take a number of steps to assure public
safety. The agency has recommended that the industry:
•
•
•
Support needed research into possible biological
effects of RF of the type emitted by mobile phones;
Design mobile phones in a way that minimizes any RF
exposure to the user that is not necessary for device
function; and
Cooperate in providing mobile phone users with the
best possible information on what is known about
possible effects of mobile phone use on human
health.
-54-
At the same time, FDA belongs to an interagency working
group of the federal agencies that have responsibility for
different aspects of mobile phone safety to ensure a coordinated effort at the federal level. These agencies are:
•
•
•
•
•
National Institute for Occupational Safety and Health
Environmental Protection Agency
Federal Communications Commission
Occupational Health and Safety Administration
National Telecommunications and Information
Administration
The National Institutes of Health also participates in this
group.
In the absence of conclusive information about any possible risk, what can concerned individuals do?
If there is a risk from these products--and at this point we do
not know that there is--it is probably very small. But if people are concerned about avoiding even potential risks, there
are simple steps they can take to do so. For example, time is
a key factor in how much exposure a person receives. Those
persons who spend long periods of time on their hand-held
mobile phones could consider holding lengthy conversations on conventional phones and reserving the hand-held
models for shorter conversations or for situations when
other types of phones are not available.
People who must conduct extended conversations in their
cars every day could switch to a type of mobile phone that
places more distance between their bodies and the source
of the RF, since the exposure level drops off dramatically
with distance. For example, they could switch to:
•
•
•
A mobile phone in which the antenna is located outside the vehicle,
A hand-held phone with a built-in antenna connected
to a different antenna mounted on the outside of the
car or built into a separate package, or
A headset with a remote antenna to a mobile phone
carried at the waist.
-55-
Again, the scientific data do not demonstrate that mobile
phones are harmful. But if people are concerned about the
radiofrequency energy from these products, taking the simple precautions outlined above can reduce any possible risk.
Where can I find additional information?
For additional information, see the following web sites:
Federal Communications Commission (FCC) RF Safety
Program (select "Information on Human Exposure to RF
Fields from Cellular and PCS Radio Transmitters"): http://
www.fcc.gov/oet/rfsafety
World Health Organization (WHO) International Commission on Non-Ionizing Radiation Protection (select Qs & As):
http://www.who.int/emf
United Kingdom, National Radiological Protection
Board: http://www.nrpb.org.uk
Cellular Telecommunications Industry Association
(CTIA): http://www.wow-com.com
U.S. Food and Drug Administration (FDA) Center for
Devices and Radiological Health: http://www.fda.gov/cdrh/
consumer/index.html
-56-
Phone Performance
Technical Information
Dimensions (with antenna retracted)
With Standard NiMH Battery 133 x 46 x 27mm
With Slim Li-Ion Battery
133 x 46 x 24mm
With Extended Li-Ion Battery 133 x 46 x 27mm
Weight
With Slim Li-Ion Battery
133g
Transmitting Power
0.6 W max. ERP
Cellular Frequency Band
824.010 - 848.970 MHz (TX)
869.010 - 893.970 MHz (RX)
1850.01 - 1909.95 MHz (TX)
1930.05 - 1989.99 MHz (RX)
PCS Frequency Band
Standard Battery Capacity
Standard NiMH
Slim Li-Ion Battery
Extended Li-Ion Battery
800 mAh
1050 mAh
1400 mAh
Memory Locations
99
Memory Capacity
26 numeric digits per
location
20 letters per location
Battery Care & Disposal
Your phone battery is a sealed unit with no serviceable
parts inside; do not attempt to open the case. To ensure the
maximum life from your battery, allow the battery to fully
discharge at least once a week. To fully discharge the battery, leave the phone turned on until the message
RECHARGE
BATTERY
is displayed and the phone shuts itself off. If left unused, a
fully charged battery discharges in approximately one
month. Store batteries uncharged in a cool, dark, and dry
place.
Batteries must be recycled or disposed of properly; they
must not be disposed of in municipal waste. Contact local
waste management officials for information on the environmentally sound collection, recycling, and disposal of batteries.
-57-
Chapter 5: Warranty & Service
Limited Warranty
1.
What Products May Be Covered By This Limited Warranty?
The following products (the “Products” or the “Product”) purchased through an NEC America, Inc.
(NECAM), Wireless Communications Division Authorized Dealer (the “Dealer”) in the United States on or
after January 1, 1997, may be covered by this warranty:
[NEC 2600/2610 CELLULAR TELEPHONE]
2.
What Does This Warranty Cover?
NECAM warrants to the original end-user Product
purchaser (“You”) that the Products will conform to
the applicable published specifications in effect at
the time of shipment from NECAM to the Dealer, and
that the Products will be free from defects in materials or workmanship under normal use and service
during the warranty period described in Paragraph 4.
3.
When Does Your Warranty Begin?
The warranty period will begin on the date You purchase the product. Dated proof of purchase is necessary to accompany and product returned for warranty
service consideration. Valid proof of purchase must
identify the point of purchase, date of purchase,
Product model or trade name, and Electronic Serial
Number or Mechanical Serial Number for transceivers
and boosters.
4.
How Long Does The Coverage Last?
The warranty period for the Product is:
[ONE (1) YEAR]
Any Products repaired or replaced under the terms of
this warranty are covered under the warranty for the
remainder of the original warranty period or ninety
(90) days from the date of service return shipping,
whichever is longer.
-58-
5.
What Will The Manufacturer Do If The Product Becomes
Defective In Materials Or Workmanship During The
Warranty Period?
If any Product covered under this warranty becomes
defective in materials or workmanship during the
applicable warranty period, NECAM will, at its option,
either repair the defective product without charge for
parts and labor, or provide a replacement in
exchange for the defective Product.
6. What Is Not Covered By This Warranty?
(a) This warranty does not extend to:
(i) Products which have been subjected to misuse, accident, physical damage, improper installation, abnormal
operation or handling, neglect, inundation, fire, water, or
other liquid intrusion, or;
(ii) Products which have been damaged due to repair,
altered, or modified by anyone other than an authorized
service warranty component-level representative of
NECAM, or;
(iii) Defects caused by components, parts, or accessories
not compatible with the warranted Product, or;
(iv) Products whose warranty/quality labels, product serial
number plates or electronic serial numbers have been
removed, altered, or rendered illegible, or;
(v) Accessory items such as antenna, cables, curl cords,
cases, etc., or;
(vi) Products shipped to NECAM for repair from outside
the United States.
(b) Any other warranties, including but not limited to the
implied warranties of merchantability and fitness for a
particular purpose, shall be limited to the duration of this
warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation
may not apply to you.
(c) NECAM’s total liability for damages for any cause related
to or arising out of the use or inability to use the product,
whether in contract, negligence, strict tort, or based on
any other legal theory, shall not exceed the original price
paid for the product.
(d) In no case shall NECAM be liable for any indirect, special,
incidental, or consequential damages based upon breach
of warranty, breach of contract, negligence, strict tort, or
any other legal theory. Such damages include, but are not
limited to, loss of profits, loss of savings or revenues,
-59-
7.
inability to use the products or any associated equipment,
cost of capital, cost of any substitute equipment, facilities
or services, claims by third parties other than you, and
injury to property. These limitations do not apply to claims
for personal injury. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
How Do You Get Warranty Service?
If Your Product requires warranty service, it must be
returned to an NEC Authorized Service Center along
with a description of the Product malfunction or difficulty. You are required to substantiate warranty status with a dated proof of purchase (as explained in
item #3), inclusive of Products’s serial number (if
applicable). The address of the nearest NECAM
Authorized Service Center may be obtained by calling
(800) 637-5917, or by writing to: NEC America, Inc.,
Attention: Service Support & Administration, 1621
Walnut Hill Lane, Irving, Texas, 75038. NECAM
assumes no risk for damage or loss in transit.
If, in NECAM’s sole opinion, the Product failure is not
covered under this warranty, or proof of purchase
does not meet the terms of this warranty, you will be
notified and your authorization will be requested for
any further repair activity. Products repaired under
warranty will be returned to You, transportation prepaid.
8.
How Does State Law Apply To This Warranty?
This warranty gives You specific legal rights, and You
may also have other rights which vary from state to
state.
9.
This Warranty Is The Entire Agreement.
Unless modified in writing, signed by both You and
NECAM, this warranty is understood to be the complete and exclusive agreement.
REV: LW0120977
-60-
NEC Service Support
NEC Service Support can assist you with any additional
information that you may need in the operation your NEC
cellular telephone and NEC Authentic Accessories™. Contact NEC Service Support at the following telephone number or address.
Telephone:
1-800-637-5917*
Writing:
NEC America, Inc.
Service Support
1621 Walnut Hill Lane
Irving, Texas 75038
*The 800 number listed above also provides access to NEC
Repair Service and Parts Sales.
NEC Wireless Marketing
NEC Wireless Marketing can be contacted at the following
address or telephone number.
Telephone:
1-800-421-2141
Writing:
NEC America, Inc.
Wireless Marketing Division
1621 Walnut Hill Lane
Irving, Texas 75038
Copyright © 2000 by NEC America, Inc.
Manual Part Number: 621-0328
3rd Edition January 2000**
**This edition may include features not available in all NEC
2600/2610 phones, or may not include features available in
updated phones. Contact NEC Service Support with any
questions.
All Rights Reserved. Printed in U.S.A.
All specifications and conditions subject to change without
notice.
LICENSED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,954,951 4,942,516 4,896,260 4,829,419 4,825,364 4,686,622 4,531,182
4,396,976 4,371,923 4,121,284 4,120,583 4,435,732 4,471,385 4,672,457
4,739,396 4,675,863 4,817,089 4,912,705 5,022,024 5,121,391
-61-
Index
A
C
Accessories, Authentic 1
Acquire New System 41
Activate Network 34
Activation, Phone 1
Add to Phone Book 19
From a Call Log 17, 19
From Notepad 20
Adjusting
Earpiece Volume 10
Keypad Volume 10
Air Time 18
Alarm 36
Deactivate 36
Set 36
Turn Off 36
All Mute 44
Answering a Call 9
Any Key Answer 10, 29
Audio 33
Auto
Answer 39
Lock 29
Pause 43
Power On/Auto Power Off
36
Deactivate 36
Set 36
Call 29
Answering 9
Any Key Answer 29
Emergency Call 9
Ending 9
Placing 8
Call Log Options
Adding Prefix 17
Dialing 16
Editing Name 16
Editing Phone Number 16
Menu 16
Storing in Phonebook 17
Call Waiting 9
Caller Identification 9
Cellular Phone Number, Viewing 11
Charging the Battery 2
Charging Times, Battery 2
Clear
All Text Messages 28
Call Logs & Air Time
Counter 18
Phone Book Contents 21
Clock 35
Clock, Setting 12, 35
Connecting Battery 1
Correcting Digit Entry Error 8
B
Backlight 39
Basic Operations 7
Battery
Care & Disposal 57
Charging 2
Connecting 1
Disconnecting 1
Locking Latch 1
Battery Charge Indicator 8
D
Date, Setting 12, 35
Dialed Calls Log 15
Dialing
Fixed Digit 37
Number stored in phone
book 8
One-Touch 37
Phone number on
notepad 8
Digit Entry Error, Correcting 8
-62-
Index
Display Icons 6
Display, Standby Mode 7
DTMF
Length 30
On or Off 31
Transmit 30
E
Enabled or Disabled Word
Wrap 32
Ending a Call 9
Environment 37
F
Fixed Digit Dialing 37
G
Getting Started 1
H
Handsfree 38
Handsfree Switch 38
I
Indicator, Battery Charge 8
K
Keypad Volume, Adjusting 10
L
Language 38
Last Number Dialed, Calling 8
Link to Phone Book 43
Lock 29
Auto 29
Full 45
Keypad 40
Lock/Unlock Keypad 40
Partial 45
Phone 45
Phone Book 21
Locking Latch, Battery 1
Log
Dialed Calls 15
Missed Calls 15
Received Calls 15
Received Phone Number
15
Long Tone Use 30
M
Main Menu 14
Manual Pause 43
Marketing, NEC Wireless 61
Menu 0 Lock Phone 45
Menu 1 Call Logs 14
Menu 2 Phone Book 18
Menu 3 Message 24
Menu 4 Settings 28
Menu 5 Lock/Unlock Keypad
40
Menu 6 Silent Mode 40
Menu 7 Non Pub(lic) Mode 40
Menu 8 Digits Editing 42
Menu 9 Mute 44
Menu Navigation Keys 6
Menu Tree Overview 5
Message
Text 3, 25
Voice 3, 24
Wakeup 38
Mic Mute 44
Missed Calls Log 15
Mode
Non Public 40
Silent 40
Standby 7
Mute
All 44
Mic 44
Unmute 44
-63-
Index
N
Navigation, Menu 13
Network 33
Activate 34
Priority 35
Notepad 12
O
One-Touch Dialing 37
P
Password
Change 29
Phone 3
Set 29
Pause
Auto 43
Manual 43
Performance, Phone 1
Phone
Activation 1
Layout 4
Password 3
Performance 1
Safety 1, 46
Turning Off 7
Turning On 7
Phone Book
Add to 19
Adding Numbers from a
Call Log 19
Adding Numbers from
Scratchpad 20
Adding Prefix 23
Clearing 21
Deleting Entry 23
Dialing Phone Number 21
Editing Name 22
Editing Phone Number 22
Locking 21
Options Menu 21
Using 11
View By Location 20
View By Name 20
View By Phone Number
20
Phone Lock 45
Phone Number
Dialing Number Stored in
Phone Book 8
Select 34
View Your 39
Viewing Your 11
Phone, Turning Off 7
Phone, Turning On 7
Placing a Call 8
R
Received Calls Log 15
Reset Settings 39
Retrieving Voice Mail 11
Ring Alert 10
Ring Type 11, 33
Ring Volume 10, 33
Ringer
Escalating Alert 10, 33
Type, Selecting 11, 33
Volume, Setting 10, 33
Roll Off Order 31
S
Safety & Performance 46
Safety Precautions 46
Safety, Phone 1
Scratchpad 12
Search for System 41
Secured Conversation 33
Select Phone Number 34
Selecting Ringer Type 11
Service Support 61
-64-
Index
Setting
(Change) Password 29
Alarm, Auto On, Auto Off
36
Clock 35
Reset 39
Ringer Volume 10
Short Tone Use 30
Signal Strength, Checking 7
SMS Menu 27
Sort Order 32
Speed Dialing 37
Standby Mode Display 7
Store As Voice Mail Number 28
Storing Voice Mail Number 11
System
Acquire New 41
Search for 41
View Stored 42
T
Technical Information 57
Text Message 31
Text Message Viewer 26
Text Messages 3, 25
Alert 25
Clear All 28
Displayed Notification 25
Read 26
Types 25
Unread 26
Time, Setting 12, 35
Tone
length 30
short & long 30
transmit DTMF 30
Transmit DTMF Tone 30
Turning Off Phone 7
Turning On Phone 7
V
View
by (Phone) Number 20
by Location 20
by Name 20
Stored Systems 42
Your Phone Number 11,
39
Voice Mail
Retrieving 11
Store As Number 28
Storing Number 11
Voice Messages 3, 24
Voice Privacy 33
Volume
Adjusting Earpiece 10
Adjusting Keypad 10
Scroll Keys 10
W
Wakeup Message 38
Warranty 58
Word Wrap 32
U
Unmute 44
Using Phone Book 11
-65-