TalkTime Max 962

Owner's Manual

ATTENTION

Before Using the Phone:

It is necessary that you CHARGE your phone battery fully before attempting to make or receive a call.

Battery Disposal:

DO NOT PLACE USED BATTERIES IN YOUR REGULAR

TRASH.THIS NICKEL-CADMIUM (Ni-Cd) BATTERY MUST

BE COLLECTED, RECYCLED OR DISPOSED OF IN AN

ENVIRONMENTALLY SOUND MANNER.

Battery Recommendations:

The NEC TalkTime 900 Series cellular phone you have purchased was designed to deliver quality performance and provide you with years of use. In order to maintain optimum performance, NEC recommends that only NEC Authentic Accessories be used with the TalkTime phones.

The incineration, landfilling or mixing of nickel-cadmium (Ni-Cd) batteries with municipal solid waste stream is PROHIBITED BY LAW in most areas.

Return this battery to a federal or state approved nickel-cadmium (or “sealed lead”) battery recycler. This may be where you purchased the battery or a local seller of automotive batteries. In all states, call 1-800-637-5917, except Minnesota if further disposal information is required. In Minnesota, call 1-800-225-PRBA.

Contact local waste management officials for other information regarding the enviromentally sound collection, recycling and disposal of this battery.

In-Vehicle Operation:

For In-Vehicle Operations, the phones battery must be charged, since

In-Vehicle Adapter Kits serves only as a trickle battery charger.

IMPORTANT

READ THIS INFORMATION BEFORE

USING YOUR HAND-HELD PORTABLE

CELLULAR TELEPHONE

First introduced in 1984, the hand-held portable cellular telephone is one of the most exciting and innovative electronic products ever developed. With it you can stay in contact with your office, your home, emergency services, and others.

For the safe and efficient operation of your phone, observe these guidelines.

Your cellular telephone is a radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) energy. The phone operates in the frequency range of 824 MHz to 894 MHz and employs commonly used frequency modulation (FM) techniques. When you use your phone, the cellular system handling your call controls the power level at which your phone transmits.

The power level can range from 0.006 of a watt to 0.6 of a watt.

i

Exposure to Radio Frequency Energy

In 1991 the Institute of Electrical and Electronics Engineers (IEEE), and in 1992 the

American National Standards Institute (ANSI) updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. Over 120 scientists, engineers, and physicians from universities, government health agencies, and industry, after reviewing the available body of research, developed this updated Standard. In March, 1993, the Federal Communications Commission (FCC) proposed

the adoption of this updated Standard.

The design of your phone complies with this updated Standard. Of course, if you want to limit RF exposure even further than the updated ANSI Standard, you may choose to control the duration of your calls and operate your phone in the most power efficient manner.

Efficient Phone Operation

For your phone to operate at the lowest power level, consistent with satisfactory call quality, please observe the following guidelines:

If your phone has an extendable antenna, extend it fully. Some models allow you to place a call with the antenna retracted. However, your phone operates more efficiently with the antenna fully extended.

Hold the phone as you would any other telephone. While speaking directly into the mouthpiece, position the antenna up and over your shoulder.

Do not hold the antenna when the phone is “IN USE”. Holding theantenna affects call quality and may cause the phone to operate at a higher power level than needed.

Antenna Care and Replacement

Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Replace a damaged antenna immediately. Consult your manual to see if you may change the antenna yourself.

If so, use only a manufacturer approved antenna. Otherwise, take your phone to a qualified service center for repair.

Use only the supplied or approved antenna. Non-approved antennas, modifications, or attachments could impair call quality, damage the phone, and violate FCC regulations.

Driving

Check the laws and regulations on the use of cellular telephones in the areas where you drive. Always obey them. Also, when using your phone while driving, please:

* give full attention to driving,

* use hands-free operation, if available, and

* pull off the road and park before making or answering a call if driving conditions so require.

Electronic Devices

Most modern electronic equipment is shielded from RF energy. However, RF energy from cellular telephones may affect inadequately shielded electronic equipment.

RF energy may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles. Check with the manufacturer or its representative to determine if these systems are adequately shielded from external RF energy. You should also check with the manufacturer of any equipment that has been added to your vehicle.

Consult the manufacturer of any personal medical devices (such as pacemakers, hearing aids, etc.) to determine if they are adequately shielded from external RF energy.

Turn your phone OFF in health care facilities when any regulations posted in the areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

ii

Aircraft

Turn your phone OFF before boarding any aircraft.

* Use it on the ground only with crew permission.

* Do not use it in the air.

To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your phone while the plane is on the ground. To prevent interference with cellular systems, FCC regulations prohibit using your phone while the plane is in the air.

Children

Do not allow children to play with your phone. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna for example). Children also could damage the phone, or make calls that increase your telephone bills.

Blasting Areas

To avoid interfering with blasting operations, turn your unit OFF when in a “blasting area” or in areas posted: “Turn off two-way radio”.

Construction crews often use remote control RF devices to set off explosives.

Air Bags

An air bag inflates with great force. DO NOT place objects, including both installed or portable wireless equipment, in the area over the air bag or in the bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Potentially Explosive Atmospheres

Turn your phone OFF when in any area with a potentially explosive atmosphere.

It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.

Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fueling areas such as gas stations; below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine.

Do not transport or store flammable gas, liquid, or explosives in the compartment of your vehicle which contains your phone or accessories.

Vehicles using liquefied petroleum gas (such as propane or butane) must comply with the National Fire Protection Standard (NFPA-58). For a copy of this standard, contact the National Fire Protection Association, One Batterymarch Park, Quincy,

MA 02269, Attn: Publication Sales Division.

PACEMAKER/ICD’s

Research sponsored by the Wireless Technology Research, LLC (“WTR”), indicates that some wireless telephones cause interference with pacemakers.

Accordingly, NEC America endorses the following recommendations issued by the WTR:

Wireless phones should be kept at a safe distance from a pacemaker. Existing data indicate that the greater the distance between a pacemaker and a wireless phone, the less risk of interference. These data further indicate that six inches is the proper separation distance for minimal risk.

iii

Practical steps to achieve this separation distance include:

• The wireless telephone should not be placed over the pacemaker, such as in a breast pocket, when it is in the “ON” position. (A phone is “ON” when power is being supplied to the telephone by the battery).

• The phone should be used at the ear opposite the pacemaker.

Note: There is nothing in the comprehensive data to suggest that bystanders with pacemakers would be at risk of interference from others who are using wireless phones.

CONTROLS AND FEATURES

Antenna

Earpiece Receiver

Liquid Crystal Display

Call Control Keys

Function Keys

Dialing Keys

Microphone

Symbol Keys

Rechargeable

Battery Pack

Battery Jack

Battery Locking Catch

Sounder / Speaker

Battery

Charging

Contacts

External Connector iv

CONTENTS

Getting Started

Installing and Removing the Battery

The Battery Charge Indicator 3

Charging and Recharging the Battery 3

2

2

Display Indicators

Quick Reference Guide

Menu Functions

4

4

5

Operation of the Phone

Turning On or Off

Placing a Call

Receiving a Call

Signal Strength

Volume Keys

Last Number Redial

Speed Dialing

Menu

Facility

Shortcuts

The Memory

Storing Informaton

Group Storing

Recalling A Number From Memory

Keying In Names

Editing Names or Numbers

Displaying “Hidden” Numbers

Deleting Information

Recalling Info by Memory Number

Scanning for a Number

Scanning for a Name

Scratchpad

Displaying Own Phone Number

Additional Features

Locking/Unlocking the Phone

Length of Your Calls

Resetting the Call Timers

Setting the Backlight

Setting the Key Tones

Setting the Ringing Volume

Selecting Alert Tone

Using the Phone on Two Networks

Tone (DTMF) Dialing

10

11

11

11

9

10

9

9

11

12

12

12

12

15

15

16

16

13

13

14

14

16

17

7

7

7

7

6

6

6

6

8

8

Pauses

Memory Linking

Roaming(System Select)

Call Time Stamp

Muting/Unmuting

Low Battery Alarm

Error Tone

Self Diagnostic Alarm

Alarm Clock

Automatic Power On

Automatic Power Off

Escalating Alert

Automatic Answer

Battery Save

Automatic Lock

Restricted Digit Dialing

Speed Dial Memory Lock

Tempory Lock Code

Reset Defaults

Wake-Up Message

External Control Line

Call Alert

Radio Mute

Automatic Repeat Dialing

One Touch Dialing

Multiple Language Select

Clock/Calendar

Caller Line Identification

Viewing the Message Register

Clearing the Message Register

Voice Messaging Service

Voice Message Waiting Indication

Minute Reminder Tone

SID Management

NAM Programming

Maintenance

Care and Maintenance

Troubleshooting

Limited Warranty

Technical Information

37

37

37

38

34

34

36

36

38

38

32

32

32

33

29

30

31

32

26

27

28

29

23

24

25

26

18,19

18,19

19

21

21

22

22

22

22

39

39

39

42

-1-

GETTING STARTED

Your phone is powered by a rechargeable battery.

A new battery must be fully charged before being used for the first time.

If left unused, a fully charged battery will discharge itself in about a month. Store batteries uncharged in a cool, dark, and dry place.

The battery pack is a sealed unit with no servicable parts inside. Do not attempt to open the case.

WARNING: Use only NEC approved batteries, antennae and chargers. The use of any other types will invalidate any approval or warranty applying to the telephone.

INSTALLING AND REMOVING THE BATTERY

To Install the Battery:

1. Insert the bottom of the battery into the base of the phone.

2. Fasten it to the phone by pressing slightly downwards on the battery until the locking catch snaps into place.

3. Make sure the battery is properly installed.

To Remove the Battery:

Remember to switch the power off before removing the battery.

1. Slide the locking latch located at the top of the battery upward and gently pull the battery away from the phone.

-2-

THE BATTERY CHARGE INDICATOR

The Battery Charge Indicator can be accessed by pressing the [FCN] key after power has been applied to the phone. The display screen indicates the battery charge level ranging from

E to F. E representing low battery and F representing full battery.

When the battery charge falls to a preset level the phone displays a warning message;

RECHARGE BATTERY, and an audible double beep will sound 6 times at 10-second intervals and then automatically turn itself off.

E

©©©

F Mon

F C N

NAM-1

1234567890

■ ■ ■ ■ ■

RECHARGE

BATTERY

CHARGING AND RECHARGING THE BATTERY

Charging the battery can be accomplished two ways.

(A) By direct connect of the AC Adapter to the charging jack of the phone.

(B) By placing the phone into the charging stand.

(A)

1. Plug the AC Adapter into a standard

110V AC outlet.

2. Insert the DC plug into the phone battery jack.

3. With power on, display shows:

■ ■ ■ ■ ■

C h a r g i n g

12:00 am

H o m e

(B)

1. Plug the AC Adapter into a standard 110V AC outlet.

2. Insert the DC plug into the charging stand jack.

3. Place the phone in the charging stand.

(A) (B)

Note: Recharging of the battery usually takes approximately 10 hours.

A new battery must be fully charged before being used for the first time.

Batteries last longer and perform better if allowed to discharge fully at least once a week. You can do this by leaving the phone switched on overnight, or until the message RECHARGE BATTERY is displayed and the phone shuts itself off.

NOTE: If the battery is too hot or cold, charging will be inter-rupted until the battery reaches a normal temperature.

-3-

■ ■ ■ ■ ■

Shows cellular signal strength.

DISPLAY INDICATORS

CLOCK ALARM

Indicates clock alarm is on.

LOCK

FL-Full Lock

PL-Partial Lock

Received Signal Strength

Indicator

Current Date

Current Time

Service Area Indicator

■ ■ ■ ■ ■

FEB 2

12:00 a m

Home

■ ■ ■ ■ ■

FEB 2

12:00 a m

Home

FL

AA

CA

BS

RD

Clock Alarm Indicator

LOCK Indicator (FL)/Voice Mail Indicator (VM)

Automatic Answer Indicator

Call-Alert/Radio Mute Indicator

Battery Save Indicator

Repeat Dial

Talk Time of call in progress

In Use Indicator

■ ■ ■ ■ ■

45 m 59 s

In Use

SPECIAL FEATURE

INDICATORS

AA-Automatic Answer

CA-Call Alert

RM-Radio Mute

BS-Battery Save

RD-Repeat Dial

CURRENT TIME

Shows current time

SERVICE INDICATOR

Home

Roam

No Svc

In Use

Mute

CURRENT DATE

Shows current date

TALK TIME

Shows time of call in progress

Turn on/off

Make call

End call

Answer call

Clear digit

Clear display

Last number redial

Adjust volume

QUICK REFERENCE GUIDE

Press and hold PWR.

Key in number, press SND.

Press END.

Press SND. (Any key if Any Key Answer is ON FCN 53.)

Press CLR briefly.

Press CLR and hold.

Press SND.

Press FCN + # or

★ hold.

-4-

____________________________The Memory__________________________

Store a phone number Key in number(and/or name). Press STO (Hold).

The number is stored in the first empty memory location.

Speed Dialing Key in the number of the memory location. Press SND.

Scan through memory Press RCL + 0 + 1+ # or

★

....

Scan for a name Press RCL + # or

★

....

_____________________________The Menu___________________________

Enter menu

Scroll

Select function

Scroll

Select status

Shortcut facility

Press and hold FCN.

Press # or

★

,....

Press flashing menu number (1)(2)....

Press # or

★

,....

Press RCL.

Press FCN. Press the number of the function.

_____________

_______ List of Menu Functions

___________________

TOTAL TIME

Home,Roam

FCN + 1

FCN + 2

ALARM CLOCK

On,Off,Alm

ALPHA TAG

Names

TONE FUNCTION

Alert,Escalating, DTMF,Call, Ring

CALL PROCESSING

Auto Ans, Battery save, Any key answer, Sys Sel,

Nam select, One touch, Language, Backlight

LOCK FUNCTION

Time stamp, Auto lock, Fixed dial, End to End,

Memo lock, Temp lock, Initialize, Total time,

Wake up msg, Message clear

DATE AND TIME

Time, Date, Year

EXT CONTROL

Call Alert, Radio Mute

MUTE CONTROL

PAUSE DIAL

AUTO PAUSE

MEMORY LINK

FULL LOCK

PARTIAL LOCK

AUTOMATIC DIALING

Redials last number sent

RING TONE VOLUME

Off,Min,Low,Mid,Max

HIDDEN DIGITS

-5-

FCN + 3

FCN + 4

FCN + 5

FCN + 6

FCN + 7

FCN + 8

FCN + 9(Hold)

FCN + 0 + 0

FCN + 0 + 1

FCN + 0 + 2

FCN + #

FCN +

★

FCN + SND

FCN + 4 + 5

FCN(Hold)

OPERATION OF THE PHONE

1) Press the PWR key and hold it for at least 2 seconds.

The phone will carry out a short self-test sequence, then briefly display your wake-up message.

2) When the RSSI Indicator,Date and time and Home indicator appears on the display, the phone is ready for use.

If NO SVC appears it means that you are outside the cellular service area and the network cannot serve you.

A cellular phone can only send and receive calls when it is switched on.

3) Press the PWR key and hold it for at least 2 seconds to switch the phone off.

PLACING A CALL

Fully extend the antenna before sending or receiving a call.

Note: Push in the antenna when you are not using the phone.

You can use the phone without extending the antenna in a good coverage area.

1) Key in the number (include the area code if you’re making a long distance call).

If you make a mistake, press the CLR key to delete the last keystroke; or to clear the whole display, press and hold the CLR key.

2) The number will appear on the display.

3) Press SND.

4) The IN USE indicator will appear, and the number will disappear from the display. The call timer will appear and count.

5) Lift the phone to your ear, and wait until your call is answered.

6) When you have finished the call, press END.

If the message NO SVC appears, you are outside the cellular service area.

If lock indicators (FL)(PL) appears on the display, your phone has been electronically LOCKED (see Locking the Phone). You can still make emergency calls when the phone is locked.

RECEIVING A CALL

1) When there is an incoming call, the phone rings, and the CALL message flashes on the display.

If the ringing tone has been switched off-the flashing of the display and keypad will alert you of an incoming call.

2) Press SND (Any Key if Any Key Answer has been turned on) and lift the phone to your ear.

3) When you have finished your conversation, press END.

If you don’t answer the call, the CALLED message will remain on the display

(showing that someone has tried to phone you). Press CLR key to clear the display.

Received Signal Strength

Indicator

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

-6-

SIGNAL STRENGTH

The quality of your call depends on the strength of the cellular signal in your area.

The phone displays current signal strength as a series of bars on the left side of the display screen. The more bars, the better the signal. If the signal is poor, try moving the phone slightly to improve reception. If you are using the phone in a building, it may be necessary to move near a window, or outdoors for better reception.

VOLUME KEYS

VOL

■ ■ ■ ■ ■

FEB 2

12:00 a m

Home

The earpiece and key pad volume can be controlled by the volume keys FCN

★

or

FCN # (Hold). The volume level is shown on the display as a series of bars.

LAST NUMBER REDIAL

The last number dialed can be redialed automatically without re-entering it.

(The number can still be retrieved even if the phone has been switched off

and back on.)

1) With the display clear, press SND.

2) The number you last called will appear on the display and is automatically redialed.

■ ■ ■ ■ ■

2141234567

Last number redial can also be used from the memory;

1) Press RCL + 0 + 0.

■ ■ ■ ■ ■

LN)

2141234567

N E C A M

2) Press SND to make the call.

SPEED DIALING

The phone dials quickly by recalling phone numbers from memory using the memory location number and the SND key.

1) Press Memory Location Number (i.e.12)

■ ■ ■ ■ ■

12

Home

2) Press SND.

■ ■ ■ ■ ■

2141234567

In Use

Note: Name associated with the memory location you have requested will not be shown.

-7-

THE MENU FACILITY

The menu allows you to operate or check the setting of certain features. Although the menu method can take longer than the alternative shortcut method, it is often easier to remember.

■ ■ ■ ■ ■

FCN 1

Total Time

1) Press FCN (Hold).

2) The display will read FCN 1 Total Time. Use # or

★

to step forward or backward through the list of functions available. Press the flashing number when the desired function is displayed. Use # or

★ to step through the list of functions available. Press RCL to set the new status(the one which is displayed).

3) Use the CLR key to exit the menu function.

MENU SHORTCUTS

Each Menu function can also be controlled by a shortcut; By using the shortcut you can get to the function you want to change or check without scrolling. To activate the shortcut function simply press FCN followed by the shortcut number, (eg. FCN

5 + 1 for Auto Answer).

The menu functions available are:

Menu Function/

Description

Total Time

Alarm Set

Character Entering

Tone Function

Alert Set

Escalating Tone

Long DTMF

Call Tone

Ring Tone

Call Processing

Auto Answer

Battery Save

Any Key Answer

System Select

Dual NAM

One Touch

Language

Backlight

Shortcut

Menu Function/

Description

FCN + 1

FCN + 2

FCN + 3

FCN + 4

FCN + 4 + 1

FCN + 4 + 2

FCN + 4 + 3

FCN + 4 + 4

FCN + 4 + 5

Lock Code Function

Time Stamp

Auto Lock

Fixed Dial

End to End

Memo Lock

Temp Code

Initialize

Total Time

Wake Up Message

Message Clear

Clock Set

FCN + 5

FCN + 5 + 1

FCN + 5 + 2

FCN + 5 + 3

FCN + 5 + 4

FCN + 5 + 5

FCN + 5 + 7

FCN + 5 + 8

FCN + 5 + 9

External Control

Mute Function

Pause Dial

Auto Pause

Memory Link

Shortcut

FCN + 6

FCN + 6 + 1

FCN + 6 + 2

FCN + 6 + 3

FCN + 6 + 4

FCN + 6 + 5

FCN + 6 + 6

FCN + 6 + 7

FCN + 6 + 8

FCN + 6 + 9

FCN + 6 + 0

FCN + 7

FCN + 8

FCN + 9

(Mic Mute)

FCN + 9 Hold

(Full Mute)

FCN + 0 + 0

FCN + 0 + 1

FCN + 0 + 2

Full Lock

Partial Lock

Automatic Dialing

Key Tone Volume

FCN + #

FCN +

★

FCN + SND

FCN +

★

or

# (Held)

Review Hidden Digits

FCN Hold

For further information on menu functions see the Additional Features section.

-8-

THE MEMORY

Your phone has 99 memory locations which allow you to store numbers of up to

32 digits or names of up to 10 letters together with phone numbers of up to

32 digits. Your phone also uses memory locations 70 through 99 as permanent memory. Only authorized dealers (using special adapters) can write the phone numbers into the permanent memory locations. Your phone also keeps and displays the various information about the last 20 calls. The information shows actual talk time of the call, when the call was established (time and day of the week) and whether the call was received or sent. These locations can only be accessed by pressing RCL (Hold). A Five (5) location scrollpad memory area is also available for storage of temporary numbers.

STORING INFORMATION

1) Key in the phone number.

2) Press FCN + 3.

3) Enter in the name(see

Keying in Names, page 14).

■ ■ ■ ■ ■

@)

2141234567

WORK

4) If you want the information stored in the first available memory location, simply press STO.(hold)

5) The message Stored will be shown on the display along with the first vacant memory location.

■ ■ ■ ■ ■

S t o r e d 0 3

6) Press CLR.

Otherwise, press STO followed by a memory location number. (Example 20)

Note: If the memory location you have selected is already occupied, an alarm tone will sound, the display will flash and the contents of the memory location will be displayed.

Note: If all the memory locations are used, an alarm tone will sound, automatic store mode will be cancelled and the phone will go back to the manual store mode.

7) If you wish to overwrite the contents in this memory location, simply press STO.

8) If you do not want to overwrite the contents of the memory location, simply press

CLR.

GROUP STORING

Group storing allows you to store information in 10 dedicated memory area groups.

(Example, group 0 may be used for all persons whose names begin with the letter

“A”). The phone searches the vacant memory locations in the group specified by the user, and automatically stores the phone number and name in that group.

1) After entering phone number and/or

name(or after recalling a phone number)

■ ■ ■ ■ ■

@)

1234567

WORK

■ ■ ■ ■ ■

12)

1234567

WORK

-9-

2) Press STO +

★

.

■ ■ ■ ■ ■

G r o u p i n g

A u t o S t o r e

P r e s s 0 - 9

3) Press group number (Example 1).

The phone searches the vacant memory according to the entered number and are stored in the first vacant location in that group.

■ ■ ■ ■ ■

S t o r e d 12

example

The phone stores the number and names into the grouped vacant memory area as follows:

Input Key Memory Area

[0]

[1]

[2]

[3]

01 to 09

10 to 19

20 to 29

30 to 39

[4]

[5]

[6]

[7]

[8]

[9]

40 to 49

50 to 59

60 to 69

70 to 79

80 to 89

90 to 99

RECALLING A NUMBER FROM MEMORY

Numbers stored in any of the 99 memory locations can be recalled for viewing and or changing as the user prefers.

1) Press RCL+Memory Location Number (Example 12 if known). If not known use # or

★

to find the desired number.

■ ■ ■ ■ ■

1 2 )

1234567

WORK

KEYING IN NAMES

1) Press FCN + 3. The NAME indicator will appear on the display to show that the phone is in the name mode. When you press a key, letters will appear instead of numbers.

2) Select the key labeled with the letter you want. Press it once to obtain the first letter, twice to obtain the second, three times to obtain the third and four times to obtain the digit. If you miss the letter you want, continue to press until it is displayed again.

3) Select further letters in the same way.

■ ■ ■ ■ ■

@ )

Name

Indicator

4) If you want the same letter twice, press the # key. This allows you to advance one space, then you can select it again.

5) Note that you can enter up to 10 characters. Each “space” and “hyphen”

entry is included as part of the maximum 10 characters.

6) If you begin your memory store procedure in NAME mode when you have finished keying in the name, you must store this information to a vacant memory location before you can key in the numbers. Press RCL to recall the memory location where you stored the NAME, then you can start keying in the phone number.

-10-

EDITING NAMES OR NUMBERS

If you make a mistake while keying in a name or a number, you can correct it as follows:

1) Press CLR to delete the last character or digit.

2) Press and hold CLR to clear the whole display. Note that this clears both the name and the number entered.

DISPLAYING “HIDDEN” NUMBERS

The phone can display up to 16 digits. If you key in more than this, the first digits will disappear off the side of the display.

If you want to check these hidden digits, press and hold FCN and they will appear on the display. When you release the FCN key, the original 16 digit display will reappear.

Remember to clear the whole display (press CLR and hold) after having displayed a long number.

DELETING INFORMATION FROM MEMORY

1) Press and hold CLR to clear display.

■ ■ ■ ■ ■

2) Press STO.

)

3) The display will read.

4) Key in the number of the memory location you want to delete.

5) An alarm tone will sound, and the contents of the memory location will be displayed and flashing.

■ ■ ■ ■ ■

1 2 ) flashing

1234567

WORK

6) Press STO. The contents of the memory location will be deleted.

RECALLING MEMORY LOCATION NUMBER

1) Press RCL. The display will show.

■ ■ ■ ■ ■

)

2) Key in memory location number (Example 12).

■ ■ ■ ■ ■

12)

1234567

WORK

If the memory location is empty, the display will show.

■ ■ ■ ■ ■

12)

3) Call the number by pressing SND.

-11-

SCANNING FOR A NUMBER

1) To scan the entire memory, press RCL + 0 + 1 to display the contents of the first memory location. Use # or

★ keys to display the next or previous memory location.

2) When you find the number you want, press SND to make the call.

SCANNING FOR A NAME

1) Press RCL # to display the name memory locations from A to Z. Press RCL

★ to display the name memory locations from Z to A. The memories will be displayed in alphabetical order by the first character.

■ ■ ■ ■ ■

22)

2141234567

BILLS PC

2) When you find the name you want, make the call by pressing SND.

SCRATCHPAD

Digits can be entered during a conversation and will stay on the display after the call.

If you wish to keep the scratchpad and store it in a scratchpad memory location

(5 locations) use the use the STO function below. If End-to-End is turned ON, DTMF tones will be sent out over the voice channel unless the phone is first muted.

Note: Digits entered during a conversation will be sent over the air if the phone is not muted (and end-to-end has not been turned off). These digits also stay on the display after the call. If you wish to store the contents into the phone number memory use STO.

1) Key in the area code and phone number.

2) Press STO + 0 + 0.

3) The phone will store the number in the first scratchpad memory location (S1).

■ ■ ■ ■ ■

00)

Scratchpad

Stored

4) To view the Scratchpad memory, Press RCL + 0 + 0.

The last number dialed will appear on the screen (LN) 2141234567

Use

★

or # keys to scroll the scratch memory locations S1 through S5.

5) To store Scratchpad in a normal memory location press STO (hold).

6) The phone will store the number in the first vacant memory location and indicate the memory location on the display.

■ ■ ■ ■ ■

Stored 03

DISPLAYING YOUR OWN NUMBER

1) Press FCN

E ©©© F Tue

FCN

NAM-1

2141234567

Note: If your phone is registered on two cellular networks, the number

displayed will be for the network that is currently being used.

-12-

ADDITIONAL FEATURES

LOCKING/UNLOCKING THE PHONE

Your phone has a simple security system. It can be locked by using a four-digit lock code to prevent unauthorized use.

The lock code is supplied by the dealer. If you forget your lock code contact your dealer. The factory default lock code is 0000.

FULL LOCK

When the phone is fully locked, only emergency calls (911) can be made, but any call can be received. Storing to the memory is also prevented.

1) Press FCN + #. The display will read:

■ ■ ■ ■ ■

Enter

Lock Code

2) Enter 4-digit lock code. If you key in the correct code, FL (Full Lock) will appear in the upper right corner of the display. If the key is incorrect the display will go back to the standby mode.

■ ■ ■ ■ ■

FL

Feb 2

12:00 a m

Home

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

CORRECT

INCORRECT

Note: For security the display will not show the 4-digit lock code.

3) Unlocking is carried out in the same way. Press FCN + #, enter in your four (4) digit code. When the lock is cleared the display will go back to the standby mode. If the key is incorrect the display will remain with the FL indicator in the upper right hand corner of the display.

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

CORRECT

■ ■ ■ ■ ■

FL

Feb 2

12: a m

Home

INCORRECT

When the phone is partially locked, only emergency calls (911) and any numbers stored in memory locations 1 through 9 can be made, but any call can be received.

Storing to the memory is also prevented.

1) Press FCN +

★

. The display will read:

■ ■ ■ ■ ■

Enter

Lock Code

2) Enter 4-digit lock code. If you key in the correct code, PL (Partial Lock) will appear in the upper right corner of the display. If the key is incorrect the display will go back to the standby mode.

■ ■ ■ ■ ■

PL

Feb 2

12:00 a m

Home

CORRECT

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

INCORRECT

Note: For security the display will not show the 4-digit lock code.

-13-

3) Unlocking is carried out in the same way. Press FCN +

★

. When the lock is cleared the display will go back to the standby mode. If the key is incorrect the display will remain with the PL indicator in the upper right hand corner of the display.

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

CORRECT

■ ■ ■ ■ ■

PL

Feb 2

12:00 a m

Home

INCORRECT

LENGTH OF YOUR CALLS

The phone allows you to check the duration of your calls. Upon sending or receiving a call, the current call timer begins counting. This can be viewed at anytime on the display.

Signal Strength Indicator

Talk Time of call in progress

In Use Indicator

■ ■ ■ ■ ■

45 m 59 s

In Use

Note: The current call timer will be reset upon receipt or sending of another call. It will also be reset if PWR is turned off and on again. You can manually

reset the current call timer by pressing CLR.

RESETTING THE CALL TIMERS

Call timers are used to let you know how much air time you are using both in the home and roam modes. This will allow you to control your air time as you desire.

Your phones call timers can be reset to zero at any time you desire. To view your call timers.

1) Press FCN + 1.

■ ■ ■ ■ ■

Total Time

005 h 08 m H

002 h 17 m R

Home

Roam

Note: You must have your phones lock code before you can reset your call timers. The lock code is supplied by the dealer. If you forget your lock code contact your dealer.

The factory default lock code is 0000.

1) Press FCN + 6.

■ ■ ■ ■ ■

Enter

Lock Code

2) Enter your 4-digit lock code.

■ ■ ■ ■ ■

FCN 6

Lock Code

Function

Note: For security the display will not show the 4-digit lock code.

-14-

3) Press 8.

■ ■ ■ ■ ■

FCN 68

Total Time

Clear

4) Press STO.

■ ■ ■ ■ ■

FCN 68

Total Time

Cleared

Your Total Time timers are now reset to zero’s.

■ ■ ■ ■ ■

Total Time

000 h 00 m H

000 h 00 m R

Home

Roam

5) Press CLR (Hold) to return to standby mode.

BACKLIGHTING

The phone’s keypad and display are illuminated to make them easier to read.

The backlights come on when you press any key, and goes off 10 seconds after your last key press. To turn them on again, simply press another key.

Note: For in vehicle use while using the handsfree adapter, the backlight can be placed in the ON condition and will remain on as long as the phone is in the handsfree configuration. Once removed from the handsfree

configuration the backlight will go off 10 seconds after your last key press.

To turn the backlight on or off while in the handsfree mode:

1) Press FCN + 5.

■ ■ ■ ■ ■

FCN 5 _

Call Proc

Function

2) Press 9.

■ ■ ■ ■ ■

FCN 59

Backlight

on

3) Press RCL to turn on or off.

SETTING THE KEY TONES

These tones sound each time you press a key. You can turn the keypad tones on, off or adjust them using four levels of loudness.

1) Press PWR.

2) Press FCN # or

★

(Hold) .

VOL

■ ■ ■

FEB 2

12:00 a m

Home

Note: When the key tones are switched off, DTMF tones can still be sent.

-15-

SETTING THE RINGING VOLUME

The ringing tone sounds when there’s an incoming call. You can select the volume of the tone or switch it off, (SILENT MODE).

1) Press FCN + 4 + 5 .

■ ■ ■ ■ ■

Ring Tone

Low

2) Use RCL key to select Off,Min,Low,Mid or Max.

3) Press CLR to exit and save selection

If you select Off, when a call is coming in, the display will flash, the CALL message will appear and flash.

SELECTING ALERT TONE TYPE

The Alert Tone on your phone can be selected from four different tone combinations.

1) Press FCN + 4.

■ ■ ■ ■ ■

FCN 4 _

Tone

Function

2) Press 1.

■ ■ ■ ■ ■

FCN 41

Alert Set

1

3) Press RCL to select between the four different tone combinations.

Note: You can listen to each tone combination by pressing 1 again after the initial pressing of FCN + 4 + 1. Make sure your ringer volume is on.

4) Press CLR to exit and save selection.

USING THE PHONE ON TWO NETWORKS

The phone’s two number capability feature lets you subscribe to both cellular services in your area as well as cellular service in other cities, usually one for each network. (NAM stands for Number Assignment Module).

Note: You cannot change from one network to the other during a call. (If you are only registered on one network, you cannot access the other.)

To Change the Network:

1) Press FCN + 5.

■ ■ ■ ■ ■

FCN 5 _

Call Proc

Function

-16-

2) Press 5.

■ ■ ■ ■ ■

FCN 5 5

Dual NAM

NAM - 1

3) Press RCL to select between NAM 1 and NAM 2.

■ ■ ■ ■ ■

FCN 55

Dual NAM

NAM - 2

Note: If only one NAM has been programmed and you press the RCL key, a

alarm tone will sound and the display will show NAM-1.

■ ■ ■ ■ ■

FCN 55

Dual NAM

NAM - 1

TONE (DTMF)

When end-to-end is “ON” you can transmit numerical information as a series of tones using the tone (DTMF) feature (Example to check for messages in your answering machine). To set end-to-end “ON” or “OFF”:

1) Press FCN + 6.

■ ■ ■ ■ ■

Enter

Lock Code

2) Enter in your lock code.

■ ■ ■ ■ ■

FCN 6 _

Lock Code

Function

Note: The lock code is supplied by the dealer. If you forget your lock code

contact your dealer. The factory default lock code is 0000.

3) Press 4.

■ ■ ■ ■ ■

FCN 64

End to End

on

4) Press RCL to turn End to End on or off.

Note: End to End has to be in the ON state before DTMF Tones can be transmitted or the PAUSE feature will operate.

5) Press CLR.

■ ■ ■ ■ ■

Feb 2

12:00 a m

Home

TONE GENERATOR

There are two alternative ways to use the DTMF feature.

First, make a call in the usual way. Key in numbers onto the display. Each number is directly sent as a DTMF tone. The length of the tone depends on how you have the DTMF tone generator set.

-17-

Note: The DTMF Tone Generator has two settings, off and on. If the DTMF

Tone Generator is set to off, the phone sends each DTMF signaling tone for

100 mili seconds. With the DTMF Tone Generator set to on, the phone sends each DTMF signaling tone as long as the key is pressed, up to 3 seconds max.

1) Press FCN + 4.

■ ■ ■ ■ ■

FCN 4_

Tone

Function

2) Press 3.

■ ■ ■ ■ ■

FCN 43

Long DTMF

off

3) Press RCL to turn Long DTMF on or off.

4) Press CLR. The phone returns to normal standby.

Second, recall a number from a memory location and send it as a DTMF tone.

(RCL, and the memory location number.)

Send the DTMF tones by pressing SND.

A series of tones, each representing a number, will be heard.

Hints for Storing a DTMF Number in the Memory

If you need to place a manual pause between DTMF digits press FCN + 0 + 0. If you want to place a automatic pause between DTMF digits press FCN + 0 + 1 (P = 3

Seconds). If you want to link memory locations for a long DTMF number press FCN

+ 0 + 2.

■ ■ ■ ■ ■

0 : Pause

1 : Auto - P

2 : MemLink

PAUSES - (Manual) [FCN + 0 + 0) This function creates pauses while sending out

DTMF signaling tones during conversation mode. When a manual pause is encountered in the DTMF string, the phone will pause indefinitely, until the user presses the SND key.

More than one pause may be placed in a sequence, separating several groups of

DTMF digits.

For example, this function may be used for calling a paging system and sending commands, ID numbers (PIN), and/or numeric messages:

(1) (2) (3) (4) (5)

“123456789” + “P” + “123456789#” + SND + SND

(1) This is the phone number to be called via the cellular system.

(2) This character indicates a Manual Pause. The user will wait for the initial prompt from the paging system before pressing the SND key.

(3) This a DTMF digit sequence which may represent the PIN of the called pager.

(4) This is the initial send keypress which causes the phone to initiate a call using the number up to the first pause mark.

(5) This is the second send keypress, while in conversation mode, which will end the manual pause and start the sending of DTMF digits.

-18-

PAUSES - (Automatic) [FCN + 0 + 1] This function creates pauses while sending out DTMF signalling tones during conversation mode. When an automatic pause is used, the phone will pause for three (3) seconds and then continue dialing the

DTMF sequence.

Multiple pauses may be placed together to extend the duration of the pause - i.e. 6,

9, 12 seconds etc.

For example, this function may be used for calling a paging system and sending commands, ID numbers (PIN, and/or numeric messages:

(1) (2) (3) (4) (5) (6) (7)

“123456789” + “,” + “,” + “123456789#” + “,” + “987654321#” + SND

(1) This is the phone number to be called via the cellular system.

(2) This is an Automatic Pause character which indicates a 3 second delay.

(3) This is a second Automatic Pause character indicating a 3 second delay. The phone will wait a total of 6 seconds before continuing with the following DTMF digits.

(4) This is a DTMF digit sequence which may represent the PIN of the called pager.

(5) This is an additional Automatic Pause mark. The phone will wait 3 seconds before continuing with the following DTMF digits.

(6) This is a continuation of the DTMF digit sequence which may represent the numeric message to be sent to the pager.

(7) This is the Send keypress which causes the phone to initiate a call.

MEMORY LINKING - [FCN + 0 + 2] Memory Linking is a function that allows a phone number to be chained together with a memory recall number for the purpose of adding DTMF signalling digits after a number is to be sent.

For example, this function may be used to link individual long-distance recall numbers to a single recall number which holds credit card information. The primary recall number(s) would contain the link information:

Recall #01

(1) (2) (3) (4)

“123456789” + “L” + “99” + SND

(1) This is the phone number to be called via the cellular system.

(2) This is a linking mark which indicates that the following two digits represent the recall number to be linked.

(3) This is the number of the memory recall location to be linked, and therefore treated as DTMF signalling.

(4) This is the Send keypress which causes the phone to initiate a call.

Note: Once the call is placed a pause is automatically inserted and the user must press the SND key in order to output the linked DTMF sequence.

ROAMING(SYSTEM SELECT)

Each cellular service area can have two cellular service suppliers called carriers. One carrier is called the “A” system and the other carrier is called the “B” system. Your phone is designed to work with either or both carriers.The system priority feature allows you to program your phone for optimum operation when in your home serving area or when away from your home area. This is called roaming. When you buy your phone, you may register (receive a phone number) with either or both of your local carriers. Contact the office of your home cellular phone company for information about the roaming agreements they have with other cellular phone companies .In

some areas, roaming telephones are automatically recognized by the cellular system’s computer. In other areas, you must contact the cellular phone operator before it can recognize your phone. The company needs to know your telephone number, your phone’s ESN (electronic serial number), and how you plan to pay for your calls. There is usually an additional charge for roaming calls.

Note: The ESN for your phone is located in the battery compartment of the phone, and comprises of the first 8 digits preceded by NEC’s company code of 189.

-19-

To Select the Roaming Mode:

1) Press FCN + 5.

■ ■ ■ ■ ■

FCN 5_

C a l l P r o c

F u n c t i o n

(2) Press 4. The phone will display its current roaming mode.

■ ■ ■ ■ ■

FCN 54

Sys Select

Standard

(3) Press RCL to advance through the system selections.

Home Only

This service is limited to the Home Area. Will go to “No Svc” if home SID is not detected.

■ ■ ■ ■ ■

FCN 54

Sys Select

Home only

Sys A only

This service is limited to the ‘A’ carrier only.

■ ■ ■ ■ ■

FCN 54

Sys Select

Sys A only

Sys B only

This service is limited to the ‘B’ carrier only.

■ ■ ■ ■ ■

FCN 54

Sys Select

Sys B only

Standard/Preferred

Standard allows the phone to first search for a free channel in the Home system.

If the phone cannot find a free channel, it searches the other system.

Preferred System ID's of the systems on which you wish to roam. If the unit does not detect your home SID but does detect a SID you have programmed in as an acceptable SID, the unit will roam and indicate "Preferred". If the unit does not detect your home SID or any SID which has been programmed into your phone as acceptable, then the phone will go to “No Svs”.

■ ■ ■ ■ ■

FCN 54

Sys Select

Standard

Note:The home system depends on the current NAM selection.

The ROAM/PREFERRED indicator will be displayed when you are using a system that is not your home system.

■ ■ ■ ■ ■

Feb 2

12:00 a m

Preferred

■ ■ ■ ■ ■

Feb 2

12:00 a m

Roam - A

■ ■ ■ ■ ■

Feb 2

12:00 a m

Roam - B

-20-

CALL TIME STAMP

The phone keeps and displays the various information about the last 20 incoming and/or outgoing calls. The information shows the actual talk time of the call, when the call was established (Time and day of the week) and whether the calls were incoming or outgoing calls.

1) Press RCL(Hold).

2:30 a Tue

01) 59 m 59 s

2141234567

N E C E L E C T

2) Press # or

★

key to scroll through calls.

2:30 a Tue

01) 59 m 59 s

2141234567

NEC ELECT

Outgoing Call

2:30 a Tue

01) 59 m 59 s

Receiving

Incoming Call

3) Press STO+Memory Location (Example 12 to store the number) or CLR to exit.

4) To clear Time Stamp Memory Press FCN + 6. Enter four (4) digit lock code.

Press 1. Display shows Time Stamp Clear. Press STO. Display shows Cleared.

Press CLR. Display goes to normal standby.

MUTE

The Mute function operates only when the phone is in the conversation mode.

There are two (2) Mute positions, MIC MUTE or FULL MUTE.

MIC MUTE - This function switches off the microphone while in the conversation mode.

FULL MUTE - In the portable configuration, this function switches off both the microphone and the earpiece while in the conversation mode. While mounted in a vehicle

(HF Adapter), this function turns off the phones external microphone and speaker.

MIC MUTE:

1) Press FCN + 9. This switches off the microphone.

■ ■ ■ ■ ■

03 m 06 s

Mic Mute

2) Press FCN + 9. This switches the microphone back on.

■ ■ ■ ■ ■

03 m 06 s

FULL MUTE:

1) Press FCN + 9(Hold). This switches off both the microphone and earpiece or speaker.

■ ■ ■ ■ ■

03 m 06 s

Full Mute

2) Press FCN + 9. This switches the microphone and speaker back on.

■ ■ ■ ■ ■

03 m 06 s

-21-

LOW BATTERY ALARM

The Low Battery Alarm warns the user when the battery power is getting low, by emitting a short double tone. The double tone will sound 6 times at 10 second intervals and the display will show RECHARGE BATTERY. After hearing these tones you have approximately 60 seconds before the phone shuts itself off.

■ ■ ■ ■ ■

RECHARGE

BATTERY

If you have a call in progress, the phone terminates the call and turns off the phone automatically.

ERROR TONE

A Error Tone will sound to inform the user of miss key operations, or when a keypress is ignored.

SELF DIAGNOSTIC CHECK

The phone will show a blank display if it finds any trouble within the unit during its self diagnostic check. If this occurs, immediately turn the phone off and return it to your dealer for repair.

ALARM CLOCK FUNCTION

This is the time setting function to make the clock alarm. The power turns ON automatically if the power is off at the alarm set time. The clock alarm operates only once, therefore, it is necessary to reset the phone for the next alarm. The clock alarm will sound for 20 seconds unless the [CLR] key is pressed. If no key is pressed, the phone will turn off the power when the alarm stops. If any key except

[CLR] is pressed, the alarm continues for 20 seconds and phone remains on.

Setting the Alarm:

1) Press FCN + 2.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM - - : - flashing

2) Press STO. The flashing moves to the hour field.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM 12 : 00 a flashing

3) Enter Alarm Time(i.e.11). Press RCL during the time is flashing to change to either AM or PM.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM 11 : 00 a flashing

-22-

4) Press STO. The flashing moves to the minutes field.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM 11 : 00 a flashing

5) Enter Alarm Time(i.e.31).(00 to 59 are valid entries for Minutes)

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM 11 : 31 a flashing

6) Press STO. The phone alarm is set at 11:31 AM and the flashing minute field stops flashing. The setting mode ends and the display shows:

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM 11 : 31 a

flashing

7) Pressing RCL turns the Alarm Indicator on or off.

■ ■ ■ ■ ■ Clock Alarm Indicator

ON - - : - -

OFF - - : - -

ALM 11 : 31 a

flashing

8) Press CLR. The phone returns to normal standby with the Alarm Indicator either

On or Off.

■ ■ ■ ■ ■

Feb 2

12 : 00 a m

Home

Setting Automatic Power On:

This is the time setting function to turn on the power automatically. Once this function is set, the phone will automatically power on every day at the same time.

This function can be set and reset by pressing RCL.

1) Press FCN + 2.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM - - : - -

flashing

2) Press # or

★

. The flashing position moves up or down.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM - - : - -

flashing

3) Press STO. The flashing moves to the hour field.

■ ■ ■ ■ ■

ON 12 : 00

OFF - - : - -

ALM - - : - -

flashing

-23-

4) Enter Automatic On Time (Example 8). Press RCL during the time is flashing to change to either AM or PM.

■ ■ ■ ■ ■

ON 8 : 0 0 a

OFF - - : - -

ALM - - : - flashing

5) Press STO. The flashing moves to the minutes field.

■ ■ ■ ■ ■

ON 8 : 0 0 P

OFF - - : - -

ALM - - : - flashing

6) Enter Automatic On Time (Example 59). (00 to 59 are valid entries for Minutes)

■ ■ ■ ■ ■

ON 8 : 5 9 p

OFF - - : - -

ALM - - : - flashing

7) Press STO. The phone sets at 8:59PM and the flashing minute stops flashing.

The setting mode ends and the display shows:

■ ■ ■ ■ ■

ON 8 : 5 9 p

OFF - - : - -

ALM - - : - flashing

8) Pressing RCL turns the automatic power on feature on or off by displaying the power on time when its on and all dashes when the feature is off.

9) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

Feb 2

12 : 0 0 a m

Home

Setting Automatic Power Off:

This is the time setting function that will turn off the power automatically. The power will turn itself off automatically if it is on, and the set time is reached. Once this function is set, the phone will turn off its power automatically every day at the same time. This function can be set and reset by pressing RCL.

1) Press FCN + 2.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM - - : - flashing

2) Press # or

★

. The flashing position moves up or down.

■ ■ ■ ■ ■

ON - - : - -

OFF - - : - -

ALM - - : - flashes

-24-

3) Press STO. The flashing moves to the hour field.

■ ■ ■ ■ ■

ON - - : - -

OFF 1 2 : 0 0 a

ALM - - : - flashes

4) Enter Automatic Off Time (Example 8) Press RCL during the time is flashing to change to either AM or PM.

■ ■ ■ ■ ■

ON - - : - -

OFF 8 : 0 0 a

ALM - - : - flashes

5) Press STO. The flashing moves to the minutes field.

■ ■ ■ ■ ■

ON - - : - -

OFF 8 : 0 0 a

ALM - - : - flashes

6) Enter Automatic Off Time (Example 30). (00 to 59 are valid entries for Minutes)

■ ■ ■ ■ ■

ON - - : - -

OFF 8 : 3 0 a

ALM - - : - flashes

7) Press STO. The phone sets at 8:30PM and the flashing minute stops flashing.

The setting mode ends and the display shows:

■ ■ ■ ■ ■

ON - - : - -

OFF 8 : 30 p

ALM - - : - flashing

8) Pressing RCL turns the automatic power off feature on or off by displaying the power off time when its on and all dashes when the feature is off.

9) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

Feb 2

12 : 00 a m

Home

ESCALATING ALERT

If this function is set to ON, at the incoming call, Alert tones get louder and louder.

The volume will automatically increase from “Min”,“Low”,“Mid” to “Max” every six (6) seconds at each level. The starting volume will always be “Min”, regardless of the manual ringer volume setting, unless the volume setting is off.

1) Press FCN + 4.

■ ■ ■ ■ ■

F C N 4 _

T o n e

F u n c t i o n

-25-

2) Press 2.

■ ■ ■ ■ ■

F C N 4 2

E s c a l a t i n g

o f f

3) Press RCL. This turns the function on or off.

■ ■ ■ ■ ■

F C N 4 2

E s c a l a t i n g

o n

4) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

AUTOMATIC ANSWER

The phone will automatically answer the incoming call approximately six (6) seconds after thze first alert in the HANDSFREE MODE ONLY.

1) Press FCN + 5.

■ ■ ■ ■ ■

FCN 5 _

C a l l P r o c

F u n c t i o n

2) Press 1.

■ ■ ■ ■ ■

FCN 51

A u t o A n s

o f f

3) Press RCL. This turns the Auto Ans Function on or off.

■ ■ ■ ■ ■

FCN 51

A u t o A n s

o n

4) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2 A A

1 2 : 0 0 a m

H o m e

(“AA displayed in

Hands Free Mode only.)

BATTERY SAVE MODE

This function is controlled by your carrier service and automatically reduces the transmitting power or turns off the transmitter when the user takes a pause during conversation (a pause in which the user does not speak). If this function is set to on, the BS (Battery Saving)indicator appears on the display.

1) Press FCN 5.

■ ■ ■ ■ ■

F C N 5 _

C a l l P r o c

F u n c t i o n

-26-

2) Press 2.

■ ■ ■ ■ ■

F C N 5 2

B a t t S a v e

o f f

3) Press RCL. To turn Battery Save on or off.

■ ■ ■ ■ ■

F C N 5 2

B a t t S a v e

o n

4) Press CLR. The phone returns to normal standby and shows the BS indicator.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m B S

H o m e

Note: When the phone is in the Handsfree configuration, the BS indicator will not be displayed.

AUTOMATIC LOCKING

With this function activated, the phone places itself into Full Lock condition upon power on. The four (4) digit lock code or the three (3) digit Temporary Lock Code must be used to unlock the phone.

1) Press FCN + 6.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

2) Enter four (4) digit lock code.

The lock code is supplied by the dealer. If you forget your lock code, contact your dealer. The factory default lock code is 0000.

■ ■ ■ ■ ■

F C N 6 _

L o c k C o d e

F u n c t i o n

3) Press 2.

■ ■ ■ ■ ■

F C N 6 2

A u t o L o c k o f f

4) Press RCL. To turn Auto Lock on or off.

■ ■ ■ ■ ■

F C N 6 2

A u t o L o c k

o n

5) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

-27-

RESTRICTED DIGIT DIALING

The phone allows you to restrict the number of digits on outgoing overseas calls or other long distant phone numbers. The phone will verify the number’s digit count after the SND key is pressed. The range of entry digits is from ‘0’ through ‘31’.

Entering ‘0’ resets the function to normal, unrestricted dialing.

1) Press FCN + 6.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

2) Enter four (4) digit lock code.

The lock code is supplied by the dealer. If you forget your lock code, contact

your dealer. The factory default lock code is 0000.

■ ■ ■ ■ ■

F C N 6 _

L o c k C o d e

F u n c t i o n

3) Press 3.

■ ■ ■ ■ ■

F C N 6 3

F i x e d D i a l

N o r m a l

4) Press the digit key as follows:

For No Restriction — Press 0.

■ ■ ■ ■ ■

F C N 6 3

F i x e d D i a l

0 flashing

For 7-Digit Restriction — Press 7.

■ ■ ■ ■ ■

F C N 6 3

F i x e d D i a l

7

For 11-Digit Restriction — Press 11.

■ ■ ■ ■ ■

F C N 6 3

F i x e d D i a l

1 1 flashing flashing

5) Press STO. The entered number stops flashing and the data is stored to memory.

If a ‘0’ was entered, the display changes to indicate no dialing restriction.

■ ■ ■ ■ ■

F C N 6 3

F i x e d D i a l

n o r m a l

Note: If the incorrect lock code is entered, the phone will return to the normal

standby display.

Note: In the 7-digit, or 11-digit restriction mode and the user tries to make a call with a phone number with more than 7 or 11 digits, or starts with a first digit of zero (0), when the SND key is pressed the alarm tone is heard and the

phone will display Extra Dig Dialed Press CLR.

■ ■ ■ ■ ■

E x t r a D i g

D i a l e d

P r e s s C L R

-28-

SPEED DIAL MEMORY LOCKING

This function prevents, either partially or completely, unauthorized access to the speed dial numbers stored in the memory. This function also prohibits memory access, scrollpad memory access, last number dialed access and call time stamp access.

There are three separate setting for the Speed Dial Memory Lock.

off................

No restriction

read only....

Reading allowed, Deleting and Rewriting prohibited, STO key ignored,Automatic Store Ignored.

on................

DTMF Reading, Deleting and Rewriting prohibited, STO key ignored,

RCL key ignored.

1) Press FCN + 6.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

2) Enter four (4) digit lock code.

The lock code is supplied by the dealer. If you forget your lock code, contact your dealer. The factory default lock code is 0000.

■ ■ ■ ■ ■

F C N 6 _

L o c k C o d e

F u n c t i o n

3) Press 5.

■ ■ ■ ■ ■

F C N 6 5

M e m o L o c k o f f

4) Press RCL. To Select Level of Speed Dial Memory Lock.

■ ■ ■ ■ ■

F C N 6 5

M e m o L o c k

o f f

■ ■ ■ ■ ■

F C N 6 5

M e m o L o c k r e a d o n l y

■ ■ ■ ■ ■

F C N 6 5

M e m o L o c k

o n

5) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

TEMPORARY LOCK CODE SET

This function allows the user to program any three (3) digit temporary lock code to lock or unlock the phone without revealing your personal four (4) digit lock code.

Note: The three (3) digit temporary code can not be the same as the first three

digits of your personal lock code.

1) Press FCN +6.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

-29-

2) Enter four (4) digit lock code.

The lock code is supplied by the dealer. If you forget your lock code, contact your dealer. The factory default lock code is 0000.

■ ■ ■ ■ ■

F C N 6 _

L o c k C o d e

F u n c t i o n

3) Press 6.The phone shows current three (3) digit code.

Factory default code is 000.

■ ■ ■ ■ ■

F C N 6 6

T e m p C o d e

X X X

(XXX =current code)

4) Enter three (3) digits. Example 2 + 5 + 8.

■ ■ ■ ■ ■

F C N 6 6

T e m p C o d e

2 5 8

258 is flashing

5) Press STO. The flashing stops and the new code is set.

■ ■ ■ ■ ■

F C N 6 6

T e m p C o d e

2 5 8

6) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

RESET FUNCTION STATE

This function initializes all the phone’s functions to their default state.

1) Press FCN 6 and Enter your 4-digit Lock Code.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

2) Enter your four (4) digit Lock Code.

■ ■ ■ ■ ■

F C N 6 7

L o c k C o d e

F u n c t i o n

3) Press 7.

■ ■ ■ ■ ■

F C N 6 7

I n i t i a l i z e

4) Press STO.

■ ■ ■ ■ ■

F C N 6 7

I n i t i a l i z e

C o m p l e t e d

-30-

The Phone Resets to the Defaults listed below:

(1) Total Talk Time: [000h00m]

(3) Clock Alarm: [Off,12:00am]

(5) Auto Power Off: [Off,12:00am]

(7) Automatic Answer: [Off]

(9) Auto-Lock: [Off]

(11) Memory Lock: [Off]

(13) Temporary Lock Code: [000]

(15) Alert Type Select: [1]

(17) Ext Cont: [Disable]

(19) One Touch Dialing: [Off]

(21) Any Key Answer: [On]

(2) Call Time Stamp: [00m00s]

(4) Auto Power On: [Off,12:00am]

(6) Minutes Reminder: [Off]

(8) Battery Save Select: [Off]

(10) Fixed Digit Dial: [Normal]

(12) End to End Switch: [On]

(14) Escalating Alert: [Off]

(16) Last Number Memory: [Clear]

(18) Long DTMF: [Off]

(20) Multiple Language: [English]

(22) Backlight: [On]

WAKE UP MESSAGE PROGRAMMING

This function allows the user to enter a Wake-Up Message. This message appears for 4.5 seconds each time the phone is turned on.

1) Press FCN + 6.

■ ■ ■ ■ ■

E n t e r

L o c k C o d e

2) Enter four (4) digit lock code.

The lock code is supplied by the dealer. If you forget your lock code, contact your dealer. The factory default lock code is 0000.

■ ■ ■ ■ ■

F C N 6 _

L o c k C o d e

F u n c t i o n

3) Press 9.

■ ■ ■ ■ ■

F C N 6 9

W a k e U p

M e s s a g e

4) Press STO.

-

■ ■ ■ ■ ■

5) Enter the alphanumeric data.

Select the key labeled with the letter you want. Press it once to obtain the first letter, twice to obtain the second, three times to obtain the third letter, and four times to obtain the number. If you miss the letter you want, continue to press until it is displayed again. If you want the same letter twice, press the # key. This, allows you to advance one space, then you can select it again. You can enter up to 30 characters. Each “space” and “hyphen” entry is included as part of the maximum 30 characters.

■ ■ ■ ■ ■

S A L E S

A G E N C Y

-31-

6) Press STO. The wake-up message will be stored into memory.

■ ■ ■ ■ ■

F C N 6 9

W a k e U p

M e s s a g e

7) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

EXTERNAL CONTROL LINE

This function is used in conjunction with the Handsfree Kit and sets the phone to the Call Alert or Radio Mute mode.

Call Alert (Hands-Free Mode Only)

The phone sends out a Call Received signal to a external alerting device such as your vehicle horn or lights. When your vehicle’s ignition is turned off, the phone’s power remains on and in standby. Power to your phone will be removed automatically five (5) hours after the ignition has been turned off.

Radio Mute (Hands-Free Mode Only)

The phone sends out a Muting signal to your car’s radio system when a call is received and you answer. This signal automatically lowers the volume of your vehicle’s radio. Upon ending the call your vehicle’s radio volume automatically returns to its previous setting.

1) Press FCN + 8.

■ ■ ■ ■ ■

F C N 8

E x t C o n t

D i s a b l e

2) Press RCL. To set External Control to Disable,Call Alert or Radio Mute.

■ ■ ■ ■ ■

F C N 8

E x t C o n t

C a l l A l e r t

■ ■ ■ ■ ■

F C N 8

E x t C o n t

R a d i o M u t e

3) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m C A

H o m e

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m R M

H o m e

(“CA” or “RM” displayed in Hands Free Mode Only)

AUTOMATIC REPEAT DIALING

The phone is capable of automatically redialing the same phone number up to three times with a 60-second interval between each try. After the third try, the phone will automatically cancel the repeat dial mode and go back to normal standby.

1) Enter a number (or press RCL for a memory location)

■ ■ ■ ■ ■

1 2 3 4 5 6 7

H o m e

-32-

2) Press FCN + SND. The phone will show the “RD” indicator, sound a ringing tome and dial the number selected. After thirty-five (35) seconds, if the call is not answered, the phone automatically terminates the call and the display will show:

■ ■ ■ ■ ■

R D

■ ■ ■ ■ ■

R D

0 0 m 3 6

1 2 3 4 5 6 7

M i c M u t e H o m e

After sixty (60) seconds, the phone will try to dial the same number again. The phone will sound a ringing tone and redial the number selected. After thirty-five seconds, the phone automatically terminates the call again if the call is not answered and the display again will show:

■ ■ ■ ■ ■

R D

■ ■ ■ ■ ■

R D

0 0 m 3 6 s

1 2 3 4 5 6 7

M i c M u t e H o m e

This process is repeated three (3) times. If after the third time the call is not answered the repeat dial mode ends and the “RD” indicator disappears from the display.

■ ■ ■ ■ ■

0 0 m 3 6 s

H o m e

3) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

ONE TOUCH DIALING

When One-Touch dialing is enabled, the user will have up to nine (9) one-touch keys available. Each one-touch key corresponds to one of the first nine (9) memory locations (Example one-touch 1 = RCL 01). When turned on this function will allow the user to press a single digit (1 through 9 Hold) and have the phone automatically display and dial (SND) the number residing in that memory location.

1) Press FCN + 5.

2) Press 7.

■ ■ ■ ■ ■

F C N 5 _

C a l l P r o c

F u n c t i o n

■ ■ ■ ■ ■

F C N 5 7

O n e - T o u c h

o f f

3) Press RCL. This turns One-Touch on or off.

■ ■ ■ ■ ■

F C N 5 7

O n e - T o u c h

o n

4) Press CLR. The phone returns to normal standby.

■ ■ ■ ■ ■

F e b 2

1 2 : 0 0 a m

H o m e

-33-

MULTIPLE LANGUAGE SELECTION

Your phone has the capability of displaying three (3) different languages on the display. The user can select which language (English,French,Spanish) they feel most confortable with, and the phone will remain in that language until changed.

The default language is English.

1) Press FCN + 5.

2) Press 8.

■ ■ ■ ■ ■

F C N 5 _

C a l l P r o c

F u n c t i o n

■ ■ ■ ■ ■

F C N 5 8

L a n g u a g e

E n g l i s h

3) Press RCL. This changes the language function from English,French or Spanish.

■ ■ ■ ■ ■

F C N 5 8

L a n g u a g e

F r a n c a i s e

■ ■ ■ ■ ■

F C N 5 8

L a n g u a g e

E s p a n o l

4) Press CLR. The phone returns to normal standby in a different language.

■ ■ ■ ■ ■

F E B 2

1 2 : 0 0 a m

B a s e

Spanish for (Home)

CLOCK AND CALENDAR SETTING

This function sets the year, month, day and time. The phone automatically sets the day of the week every time when the year,month and the day are set. The Year range is from 1994 to 2093.

1) Press FCN + 7. The display shows the data set screen:

■ ■ ■ ■ ■

1 2 : 0 0 a m

N o v 3 T h u

1 9 9 7

12 is flashing

2) Key in correct hour (Example 9,11,4,etc).

■ ■ ■ ■ ■

9 : 0 0 a m

N o v 3 T h u

1 9 9 7

9 is flashing

3) Press STO. The hour is set and the display moves to minutes.

■ ■ ■ ■ ■

9 : 0 0 a m

N o v 3 T h u

1 9 9 7

00 is flashing

4) Key in correct minutes (Example 15,31,59, etc).

■ ■ ■ ■ ■

9 : 3 1 a m

N o v 3 T h u

1 9 9 7

31 is flashing

-34-

5) Press RCL to select either AM or PM.

■ ■ ■ ■ ■

9 : 3 1

N o v 3 T h u

1 9 9 7

“am” / “pm”

6) Press STO. The minutes are now set and display moves to month.

■ ■ ■ ■ ■

9 : 3 1 a m

N o v 3 T h u

1 9 9 7

Nov is flashing

7) Enter Month Number (Example Jan=1, Feb=2, Mar=3 etc.).

■ ■ ■ ■ ■ 5 is flashing

9 : 3 1 a m

5 3 T h u

1 9 9 7

8) Press STO. Month is now set and display shows day.

■ ■ ■ ■ ■ 3 is flashing

9 : 3 1 a m

M a y 3 T u e

1 9 9 7

9) Enter correct date (Example 1,10,21,30 etc.).

■ ■ ■ ■ ■

9 : 3 1 a m

M a y 1 T u e

1 9 9 7

1 is flashing

10) Press STO. Date is now set and phone automatically enters in the day of the week (Example Mon,Tue,Wed,Thur,etc.).

■ ■ ■ ■ ■

9 : 3 1 a m

M a y 1 T u e

1 9 9 7

1997 is flashing

11) Enter in correct year (Example 1997,1998,1999, etc.).

■ ■ ■ ■ ■

9 : 3 1 a m

M a y 1 S u n

1 9 9 7

1997 is flashing

12) Press STO. Year is now set and display goes back to hour and flashes.

■ ■ ■ ■ ■ 9 is flashing

9 : 3 1 a m

M a y 1 M o n

1 9 9 7

Note: If correct year is already displayed press STO.

13) Press CLR. The phone returns to normal standby with the correct date and time.

■ ■ ■ ■ ■

M a y 1

9 : 3 1 a m

H o m e

-

35

-

CALLER LINE IDENTIFICATION

The caller line identification feature (when available) allows the phone number of the incoming call to appear on the phone display. Contact your cellular service provider for information on caller line identification.

With the phone in standby, an incoming call appears on the display as shown below.

■ ■ ■ ■ ■

2 : 2 0 p

P A G E 01

5 5 5 1 2 1 2

Time of Incoming Call

Incoming Call Phone Number

If the incoming call, also referred to as a page, is not answered, the caller line identification information remains on the display. The displayed incoming phone number can then be dialed by pressing SND or the information can be removed from the display by pressing CLR.

If another incoming call is received before the previous incoming call information has been cleared from the display, the new incoming call information appears as shown below.

■ ■ ■ ■ ■

2 : 2 5 p

P A G E 0 2

1 2 3 4 5 6 7

Time of Incoming Call/Page

Indicates Second Incoming

Call/Page Received

Incoming Call Phone Number

As incoming calls are received, the call/page indicator increases up to a maximum of 10. If more than 10 incoming calls are received before any information is cleared from the display, all new incoming calls are indicated as PAGE 10. If the phone is powered off before the caller line information is viewed and cleared, the latest incoming call information is again displayed when the phone is powered on.

With a call in progress, an incoming call/page is also indicated on the phone display. The IN USE indicator, displayed when a call is in progress, is replaced with the caller line identification information. The caller line identification information can be cleared from the screen by pressing CLR; the IN USE indicator is then redisplayed for the current call in progress. The call in progress can be terminated by pressing

END and the displayed incoming call/page then dialed by pressing SND.

The last 10 incoming caller identfication numbers can be viewed by accessing the the message register as described below.

VIEWING THE MESSAGE REGISTER

The message register stores up to the 10 latest caller line identification messages for viewing. Once there are 10 messages in the register, the oldest message is discarded as a new message is received.

To view the caller messages stored in the message register:

1) Press and hold RCL to access the call time stamp register.

1 1 : 2 1 a M o n

0 1] 0 0 m 0 8 s

R e c e i v i n g

-36-

2) Press and hold RCL again to access the message register. The latest message received is displayed.

Time Message Received

Message Number

5 : 4 0 p F r i

[ 0 1 ]

2 1 4 1 2 3 4 5 6 7

P A G E

Day Message Received

Caller Line

Identification Number

3) Press # or

★

to scroll through the message register. The phone beeps to indicate the last message stored in the register is displayed.

5 : 4 0 p F r i

[

0 1 ]

2 1 4 1 2 3 4 5 6 7

P A G E

Time/Day Message Received

Message Number

Caller Line Number

5 : 3 8 p F r i

[ 0 2 ]

2 1 4 5 5 5 1 2 1 2

P A G E

4) Press SND to dial a displayed caller line number stored in the message register.

CLEARING THE MESSAGE REGISTER

The message register can be cleared and all contents erased.

1) Press FCN + 6 (Lock Code) + 0.

■ ■ ■ ■ ■

F C N 6 0

M e s s a g e

C l e a r

2) Press STO to clear the message register contents.

■ ■ ■ ■ ■

F C N 6 0

M e s s a g e

C l e a r e d

VOICE MESSAGING SERVICE

Cellular Digital Messaging Service (CDMS), if available through the cellular service provider in the area, is a voice message service for the cellular customer. When a cellular customer turns off or does not answer the cellular phone, or when the customer is currently on a call, CDMS answers the incoming call. The caller is provided with the option to leave a message. The cellular phone user is notified of messages through the voice message waiting indication described below.

VOICE MESSAGE WAITING INDICATION

When an incoming caller leaves a message through the cellular provider's digitial messaging service as described above, the cellular phone user is notified by a voice message waiting indication. Upon receiving a voice message, the phone beeps and displays the following indication.

Voice Message Indication

■ ■ ■ ■ ■

VM

2 : 2 0 p

Time Voice Message

Received

VM 01

Indicates Number of

Voice Messages Received

The phone beeps and the indication appears whether the phone is in standby or in use when the voice message is received. The voice message information can be removed from the display by pressing CLR. If additional voice messages are received before the current voice message waiting information is cleared from the display, the voice message number indicator increases.

-37-

After the voice message waiting notification has been cleared, a voice message indication (VM) appears in the upper right corner of the standby display until the voice message(s) are retrieved from the cellular provider's digital messaging service.

■ ■ ■ ■ ■

VM

M a r 1 0

1 2 : 3 5 p m

Ho m e

Voice messages can be retrieved from the messaging service by following the service provider instructions for voice message retrieval.

MINUTE REMINDER TONE

During conversation on the phone, the phone will make short tones every minute to remind you that one minute of air time as been used. The minute reminder tone can be set on or off as you desire.

1) Press FCN + 4. The display will show the Tone Function menu:

■ ■ ■ ■ ■

FCN 4_

Tone

Function

2) Press 4. The display shows the currently selected Call Tone mode.

■ ■ ■ ■ ■

FCN 44

Call Tone

off

3) Press RCL to select the setting ‘on’ or ‘off’.

■ ■ ■ ■ ■

FCN 44

Call Tone

on

4) Press CLR The phone returns to normal standby.

■ ■ ■ ■ ■

Feb 2

12 : 00 am

Home

While in the conversation mode, a “Double Beep” will sound at the end of each minute. A “Single Beep” will sound ten seconds before the end of each minute.

SID MANAGEMENT

The SID Management feature lets the phone operate only within specifically identified (Preferred) systems. You can enter up to thirty (30) preferred System ID numbers that identify the systems that you want your phone to access.

Programming of your System ID numbers is accomplished by your service provider and is only associated with NAM1.

NAM PROGRAMMING

Consult your dealer for NAM Programming information.

-38-

CARE AND MAINTENANCE

Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you enjoy this product for many years.

Keep it dry. (Water contains minerals that will corrode electronic circuits). Avoid all liquid spills. Any form of liquid will cause permanent damage to your phone.

Do not store in hot area. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.

Do not drop it. This might cause permanent damage. The internal circuit boards can be broken.

Do not use or store in dusty, dirty areas. This will cause permanent damage to moving parts.

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it.

Wipe it with a soft cloth slightly dampened in a mild soap-and-water solution. If the unit is not working properly, take it to your nearest authorized dealer. The personnel there will assist you, and, if necessary, arrange for service.

TROUBLESHOOTING

If the power does not come on or stay on:

Make sure the battery is installed in the phone properly.

Be sure the contacts are clean on the battery and the charger.

Battery charge may be too low for operation. Listen for the low battery alarm or check battery level by pressing FCN.

If the power comes on, but the phone does not work:

Check the NO Service (NO SVC) message, you might be out of the cellular service area.

Make sure that the antenna is extended to its full length.

LIMITED WARRANTY

1. What Products May Be Covered By This Limited Warranty?

The following products (the "Products" or the "Product") purchased through an

NEC America, Inc. (NECAM), Wireless Communications Division Authorized

Dealer (the "Dealer") in the United States on or after January 1, 1997, may be covered by this warranty:

[TALKTIME MAX962 ANALOG CELLULAR TELEPHONE]

2. What Does This Warranty Cover?

NECAM warrants to the original end-user Product purchaser ("You") that the

Products will conform to the applicable published specifications in effect at the time of shipment from NECAM to the Dealer, and that the Products will be free from defects in materials or workmanship under normal use and service during the warranty period described in Paragraph 4.

-39-

3. When Does Your Warranty Begin?

The warranty period wil begin on the date You purchase the Product. Dated proof of purchase is necessary to accompany any Product returned for warranty service consideration. Valid proof of purchase must identify the point of purchase, date of purchase, Product model or trade name, and Electronic Serial

Number or Mechanical Serial Number for transceivers and boosters.

4. How Long Does The Coverage Last?

The warranty period for the Product is:

[ONE (1) YEAR]

Any Products repaired or replaced under the terms of this warranty are covered under the warranty for the remainder of the original warranty period or ninety (90) days from the date of service return shipping, whichever is longer.

5. What Will The Manufacturer Do If The Product Becomes Defective In

Materials Or Workmanship During The Warranty Period?

If any Product covered under this warranty becomes defective in materials or workmanship during the applicable warranty period, NECAM will, at its option, either repair the defective Product without charge for parts and labor, or provide a replacement in exchange for the defective Product.

6. What Is Not Covered By This Warranty?

(a) This warranty does not extend to:

(i) Products which have been subjected to misuse, accident, physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water, or other liquid intrusion, or;

(ii) Products which have been damaged due to repair, altered, or modified by anyone other than an authorized service warranty component-level representative of NECAM, or;

(iii) Defects caused by components, parts, or accessories not compatible with the warranted Product, or;

(iv) Products whose warranty/quality labels, product serial number plates or electronic serial numbers have been removed, altered, or rendered illegible, or;

(v) Accessory items such as antenna, cables, curl cords, cases, etc., or;

(vi) Products shipped to NECAM for repair from outside the United States.

(b) Any other warranties, including but not limited to the implied warranties of merchantibility and fitness for a particular purpose, shall be limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

(c) NECAM's total liability for damages for any cause related to or arising out of the use or inability to use the product, whether in contract, negligence, strict tort, or based on any other legal theory, shall not exceed the original price paid for the product.

-40-

d) In no case shall NECAM be liable for any indirect, special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict tort, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of savings or revenues, inability to use the products or any associated equipment, cost of capital, cost of any substitute equipment, facilities or services, claims by third parties other than you, and injury to property. These limitations do not apply to claims for personal injury. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

7. How Do You Get Warranty Service?

If Your Product requires warranty service, it must be returned to an NEC

Authorized Service Center along with a description of the Product malfunction or difficulty. You are required to substantiate warranty status with a dated proof of purchase (as explained in item #3), inclusive of Product's serial number (if applicable). The address of the nearest NECAM Authorized Service Center may be obtained by calling (800) 637-5917 or (972) 751-750, or by writing to: NEC

America, Inc., Attention: Service Support & Administration, 1621 Walnut Hill

Lane, Irving, Texas, 75038. NECAM assumes no risk for damage or loss in transit.

If, in NECAM's sole opinion, the Product failure is not covered under this warranty, or proof of purchase does not meet the terms of this warranty, You will be notified and Your authorization will be requested for any further repair activity.

Products repaired under warranty will be returned to You, transportation prepaid.

8. How Does State Law Apply To This Warranty?

This warranty gives You specific legal rights, and You may also have other rights which vary from state to state.

9. This Warranty Is The Entire Agreement.

Unless modified in writing, signed by both You and NECAM, this warranty is understood to be the complete and exclusive agreement.

REV: LW012097

-41-

TECHNICAL INFORMATION

Dimensions (without antenna) 147.32x50.8x27.94mm (5.8"x2.0"x1.1")

Weight 7.8 ounces

Transmitting Power

Operating Voltage

0.6 W max. ERP

4.8V(int. battery)

Frequency Band 824.040 - 848.970 MHz (TX)

869.040 - 893.970 MHz (RX)

Standard Battery Capacity 1000 mAh

Number of Channels 832

Memory Locations 99

Memory Capacity Numeric: 32 digits per location

Names: 10 letters per location

_________________________________________________________________

LICENSED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS

4,954,951

4,396,976

4,739,396

4,942,516

4,371,923

4,675,863

4,896,260

4,121,284

4,817,089

4,829,419

4,120,583

4,912,705

4,825,364

4,435,732

5,022,024

4,686,622

4,471,385

5,121,391

4,531,182

4,672,457

-42-

NEC SERVICE SUPPORT

NEC's Service Support group is ready to assist you with any additional information that you may need in the operation and integration of your NEC Cellular

Telephone and NEC Authentic Accessories. Service Support can be obtained by contacting NEC at:

Telephone:

1-800-637-5917 *

1-972-751-7500

Writing:

NEC America, Inc.

Service Support

1621 Walnut Hill Lane

Irving, Texas 75038

* The 800 number listed above also provides access to the NEC Repair Service and Parts Sales groups.

NEC Marketing & Sales

Marketing:

NEC America Inc.

Wireless Marketing Division

1555 Walnut Hill Lane

Irving, Texas 75038

1-800-421-2141

Copyright

A

1998 by NEC Corporation

Manual Part Number: 621-0313

1st Edition April 1998

Sales Agency:

NMI Corporation

14110 N. Dallas Parkway

Suite 300

Dallas, Texas 75240

1-800-CALL-NMI (225-5664)

All Rights Reserved. Printed in U.S.A.

All specifications and conditions subject to change without notice.

Alphabetical Index

-D-

Deleting

Information

Dialing

Tone(DTMF)

Restricted

One Touch

Speed

Display

Hidden No’s

Indicators

Own Number

Defaults

Resetting

-E-

Error

Tone

External

Control Line

Topic Page

-A-

Aircraft

Use on

Alarm

Battery

Clock

Diagnostic

Alert

Call

Escalating

Tone

Antenna

Care

Replacement

Automatic

Answer

Lock

Power Off

Power ON

Repeat Dial

iii

22

22

22

16

25

16

ii

ii

26

27

24

23

32

Battery

Alarm

Charging

-B-

Indicator

Installing

Recharging

Removing

Save

-C-

Call

Placing

Receiving

Length Of

Timers

Time Stamp

Caller Line ID

Care

22

3

3

2

3

2

26

6

6

14

14

21

36

39

22

32

11

4

12

30

11

17

28

33

7

Topic

Features

Additional

Page

-F-

13

Group

Storing

Guide

Quick Ref

-G-

Information

Deleting

Recalling

Storing

-I-

11

11

9

9

4

Key(s)

Names

Tones

Volume

-K-

-L-

Language

Last # Redial

Lights

Locking

Full

Partial

Temporary

10

15

7

-M-

Memory

Deleting

Editing

Grouping

Hidden Digits

Linking

Names

Recalling

Scanning

Scratchpad

Speed Dial

12

7

29 Locking

Menu

Facility

Functions

Shortcuts

Message

Register, Clearing 37

Register, Viewing 36

8

5

8

19

10

10

12

11

11

9

11

Service, Voice 37

Waiting Indication 37

Mute

Full

Radio

21

21

32

34

7

15

13

13

29

Topic

-N-

Names

Deleting

Editing

Keying In

Scanning

Storing

-O-

Operation

Own No. (View)

Pauses

Automatic

Manual

-P-

Page

18

19

18

Recall

Receiving

Redial

Resetting

Call Timers

Defaults

Ring

-R-

Escalating

Type

Volume

Roaming

Scanning

Name

Number

Scratchpad

-S-

12

12

12

SID Management 38

Speed Dial 7

Storing 9

25

16

16

19

10

6

32

14

31

11

11

10

12

9

6

12

-T-

Technical Info

Time/Date

Tones

Alert

Key

Minute Reminder

-U-

Unlock

Unmute

13

21

-V-

Volume

7

Voice

Messaging Service 37

Message Waiting 37

42

34

16

15

38

-W-

Wake-Up Message

31

Warranty Info

39

NEC Model TalkTime Max 962 Manual

OPERATION SUMMARY

Page

______________________________________________

NOTES:

• [X][X] = Memory Address 01 to 99.

[X] = Memory Address 1 to 9.

KEY OPERATION TERMS:

• Press = Press Key firmly.

• Press(Hold) = Press and hold down key.

• Turn = Change Mode

• Key-In = Enter a series of digits

_

__________________________________________________________

BASIC OPERATION:

Power On/Off:

• Press(Hold): [PWR]. For On or Off.

Place A Call:

• Key-in [Number]. Dial Number

Send A Number:

• Press [SND]

Receive A Call:

• Press [SND]

End A Call:

• Press [END]

6

6

6

6

6

___________________________________________________________

CONVENIENCE FUNCTIONS:

Edit Display:

• Presss [CLR]. Erase Digit.

Press [CLR Hold].Erase display

Backlight:

• Press [Any Key] Except [PWR]

For 10-second backlight.

View Hidden Digits:

• Press [FCN Hold].

With Number Displayed.

Earpiece Volume Control:

• Press FCN # or

★

during call.

Keypad Volume Control:

• Press FCN # or

★

during standby.

View Own Number:

• Press [FCN]

11

11

15

11

7

15

12

___________________________________________________________

MEMORY STORING AND RECALL

Store Number to Vacant Address:

• Key-in Number. Press [STO Hold].

(1st Vacant Location)

Key-in Number. Press [STO] +

[Memory Location].

Store Number to Occupied Address:

• Key-in Number. Press [STO] +

[Memory Location]. Press [STO]

again to overwrite.

9

9

NEC Model TalkTime Max 962 Manual

OPERATION SUMMARY

Page

__________________________________________________________

Store Number From Scratchpad:

o Key-in Number During Conversation.

Press [STO Hold].(1st Vacant Location)

Key-in Number During Conversation.

Press [STO] + [Memory Location].

Recall Stored Numbers:

o Press [RCL] + [Memory Location].

For Direct Recall.

Press [RCL] + [01].Press # or

★

.

For Scrolling All Locations.

Press [RCL] # or

★

.

For Scrolling By Name.

9

11

12

12

____________________________________________________________

FCN KEY OPERATIONS:

FCN : View Own Number

Battery Check

12

3

FCN 1: Total Time(View/Reset)

FCN 2: Alarm Clock(Setting)

FCN 3: Alpha Characters(Entering)

FCN 4: Tone Functions(Setting)

14

22/23/24/25

10

16/18/25/26/38

FCN 5: Call Processing(Selecting) 15/16/17

20/26/33/34/27

FCN 6: Locked Function

FCN 7: Date and Time(Setting)

FCN 8: External Control(Setting)

FCN 9: Mute Control

FCN 0: Memory Link/Pause(s)

FCN #: Phone Locking/Unlocking

FCN

★

: Partial Locking/Unlocking

FCN #,

★

(Hold): Keytone & Volume

FCN SND: Repeat Dialing

FCN (Hold): View Hidden Digits

14/17/27/28

29/30/31/32/37

34

32

21

18/19

13

13/14

7/15

33

11