Samsung DVD-V7070 DVD Player User manual

00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 1
DVD-V7070
Instruction Manual
POWER
OPEN/CLOSE
2
3
SCREEN FIT
TV/VCR
SHUTTLE
5
4
MODE/
REPEAT
6
AUDIO
7
8
9
ZOOM
OPEN/CLOSE
EJECT
ANGLE
3D SOUND
TV MUTE
CLEAR
INPUT SEL.
0
100+
DVD
VCR
SELECT
TV
VIEW
DIGEST
+
DISPLAY
VOL
POWER
DVD
.... SELECT .... VCR
F.ADV/SKIP
CH/TRK
-
REC
DISC MENU
SETUP
/ENTER
CHANNEL
REC
VIDEO
L AUDIO R
RETURN
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
LINE IN 2
www.samsungasc.com
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 2
Important Safety Instructions
WARNING:
Copy Notification
TO PREVENT DAMAGE WHICH MAY RESULT IN
FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Federal law provides severe civil and criminal
penalties for the unauthorized reproduction,
distribution, or exhibition of copyrighted motion
pictures and videotapes. (Title 17, United States
Code, Sections 501 and 506).
WARNING:
TO AVOID HAZARDOUS EXPOSURE TO
INVISIBLE LASER RADIATION, DO NOT OPEN
OR REMOVE/DEFEAT LASER TRANSPORT
PROTECTIVE HOUSING.
Macrovision Notification
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that
produce heat.
9.
Your authority to operate this FCC certified
equipment could be voided if you make changes or
modifications not expressly approved by the
manufacturer, who is responsible for compliance
with Part 15 FCC rules.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10.
Protect the power cord from being from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
NOTE TO CATV SYSTEM INSTALLER:
CAUTION:
12.
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
National Electronic Code that provides guidelines
for proper grounding and, in particular, specifies
that the cable ground shall be connected to the
grounding system of the building, as close to the
point of cable entry as practical.
To prevent fire, shock hazard, or annoying
interference, use only the recommended
accessories. To prevent electric shock, do not use
this (polarized) plug with an extension cord,
receptacle, or other outlet unless the blades can be
fully inserted to prevent blade exposure. To reduce
the risk of electric shock, do not remove the unit
cover or back. There are no serviceable parts
inside. Refer servicing to qualified personnel only.
Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a used, caution when moving the cart/apparatus combination to avoid injury from tip-over.
13.
Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
14.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or been dropped.
USER/INSTALLER CAUTION:
CUIDADO:
CAUTION
This symbol is intended to alert
the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sufficient
magnitude to constitute risk of
fire or electric shock.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance instructions in the
literature accompanying this
product.
2
Para prevenir incendio, riesgo de choque, o
interferencia enfadosa, use solamente los
accesorios recomendados. Para prevenir
electrochoque, no use este enchufe (polarizado)
con un cordón de extensión, toma de corriente, o
cualquier otra toma a menos que los dientes
puedan ser completamente insertados para prevenir
exposición de los dientes. Para reducir el riesgo de
descarga eléctrica, no remueva la cubierta o la
parte posterior del equipo. Dentro del equipo no
hay partes que requieren servicio. Diríjase
solamente a personal calificado cuando requiera
servicio.
ATTENTION:
Pour éviter les incendis, risque de chocs, ou
interférences fâcheuses, employer seulement les
accessoires recommandés. Pour éviter les chocs
électriques, ne pas employer cette prise (polarisée)
avec une rallonge, une prise de courant ou une
autre sortie de courant à moins que les lames
peuvent être insérées à fond pour l’exposition des
lames. Pour réduire les risques de chocs
électriques, ne pas retirer le couvercle ou l'arrière
du module. Il n'y a pas de pièce utilisable à
l'intérieur. Ne faire effectuer l'entretien que par un
personnel qualifié.
3
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 4
Table of Contents
Table of Contents
◆ Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
■
◆ 5 - DVD Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Disc Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TV Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alt Video Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
25
26
27
28
29
30
31
31
◆ 6 - DVD Sound Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
A/V Receiver Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
◆ 7 - DVD Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Special Playback Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Fit Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Title/Chapter/Time Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digest Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-B Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeat Chapter/Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmed Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MP3 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3D Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
34
34
35
36
36
37
37
38
39
39
40
41
42
42
43
■
◆ Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
◆ 1 - System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Front Panel Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insert Remote Control Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the TV Buttons on the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
10
11
11
12
◆ 2 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Basic Connections/Auto Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
◆ 3 - Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Deck Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic DVD Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic VHS Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic TV Tuner Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
15
16
◆ 4 - System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
On-Screen Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tuner Band Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Channel Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel Add/Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Output Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Panel Dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Power Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
17
18
19
20
21
22
22
23
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4
■
■
■
■
■
■
■
5
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 6
Table of Contents
Feature Summary
System Features
◆ 8 - VCR Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
Special VCR Playback Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S-VHS Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Search System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
44
45
45
46
◆ 9 - VCR Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
Basic Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Recording Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
One-Touch Recording (OTR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Record Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
48
49
49
◆ 10 - Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
How to Set a Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
◆ Appendix A - Advanced Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
S-Video/Component Video Connections (for DVD) . . . . . . . . . . . . . . . . . . . . . .
Stereo Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor TV Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Other Video Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
52
53
54
◆ Appendix B - Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
• Complete versatility to play DVD, VCDs, audio CDs, MP3 discs or VHS Tapes.
• Watch a DVD while recording a TV show to the VCR.
• Auto Setup automatically sets clock and searches for channels.
• Remote controls both DVD and VCR decks.
• Composite, S-Video and Component video outputs for high connectivity and optimum performance.
• RF inputs and outputs for connection to all TVs–new or old.
• English/French/Spanish on-screen programming.
DVD Features
•
•
•
•
•
10-bit video digital to analog converter and 27MHz advanced digital filter.
Playback of 96KHz/24-bit sources.
DTS digital output for DTS-enhanced DVDs.
Playback MP3 files from CD-ROM.
Continued audio during 2x speed playback.
VCR Features
•
•
•
•
•
•
Hi-Fi Stereo VCR.
4 heads for superior slow motion and stop action.
Playback of S-VHS tapes at better than standard resolution.
VISS Index Search/Scan, Zero Return, Blank Search.
8-event/1 month timer recording.
Time remaining counter, real time counter.
Note
*Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
*Ability to play back may depend on recording
conditions.
• DVD-R
• CD-RW
• DVD+RW, -RW
Unpacking
As you unpack, please check that the following items are included in your DVD-VCR packing case:
•
•
•
•
•
•
6
DVD-VCR
User’s Guide (AK68-00044A)
RCA cable for Audio/Video connection
RF (Radio Frequency) Antenna Cable
Remote Control
1.5V “AA” Batteries - 2EA
7
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 8
Disc Type and Characteristics
Front Panel Overview
This DVD player is capable of playing the following types of discs with the corresponding logos:
1
Disc Types
(Logos)
Recording
Types
DVD
Audio
+
Video
Disc Size
Max.
Playing Time
5"
Single-sided
240 min.
Double-sided
480 min.
31/2"
VIDEO-CD
5"
Audio
+
Video
AUDIO-CD
Single-sided
80 min.
Double-sided
160 min.
74 min.
31/2"
20 min.
5"
74 min.
31/2"
20 min.
3
4
5
6
OPEN/CLOSE
• DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
• Various screen and audio
functions can be easily
selected through the onscreen menu.
DVD
CHANNEL
REC
• Play
Region
Number
NTSC
• NTSC broadcast
system in U.S.A,
Canada, Korea,
Japan, etc.
• Dolby
Digital disc
STEREO
DIGITAL
SOUND
• Stereo disc
• Digital
Audio disc
• DTS disc
VIDEO
1
2
3
4
5
6
7
8
9
10
9 10 11 12
DVD DECK (p.14)
DVD OPEN/CLOSE (p.14)
VCR DECK (p.15)
CHANNEL œ/❷ (p.16)
RECORD (p.47)
DVD-VCR SELECT (p.14)
VCR EJECT (p.15)
POWER (p.14)
STOP (p.33)
REWIND/REV (p.33, 44)
13
L AUDIO R
11
12
13
14
15
16
14 15 16
PLAY/PAUSE (p.14, 15, 33, 44)
FAST-FORWARD/FWD (p.33, 44)
FRONT PANEL DISPLAY (p.10)
LINE IN 2 COMPOSITE VIDEO JACK
LINE IN 2 LEFT AUDIO JACK
LINE IN 2 RIGHT AUDIO JACK
• MP3 disc
Play Region Number
Both the DVD player and the discs are coded by region. These regional codes must
match in order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
8
.... SELECT .... VCR
LINE IN 2
8
• Video with CD sound, VHS
quality & MPEG-1
compression technology.
EJECT
POWER
Disc Markings
~
7
Characteristics
• CD is recorded as a
Digital Signal with better
audio quality, less
distortion and less
deterioration of audio
quality over time.
Audio
2
9
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 10
Remote Control Overview
Rear Panel
1
2
3
4
DVD & VCR
POWER
DVD Only
OPEN/CLOSE
18
1
2
2
3
4
TV/VCR
SHUTTLE
5
4
MODE/
REPEAT
2
3
4
5
6
7
8
9
5
6
8
ANGLE
3D SOUND
6
7
8
9
RF ANTENNA INPUT
RF OUT TO TV
LINE OUT TO TV (COMPOSITE)
LINE IN 1
AUDIO LINE OUT TO TV
(S-VIDEO OR COMPONENT)
COMPONENT VIDEO OUT
DIGITAL AUDIO OUT(COAXIAL)
DIGITAL AUDIO OUT(OPTICAL)
S-VIDEO OUT
VCR
DIGEST
SELECT
8
F.ADV/SKIP
TV
2
3
4
5
6
7
16
25
-
26
27
REC
DISC MENU
28
29
30
SETUP
/ENTER
17
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
STEREO
10
11
16
17
18
19
20
21
22
32
33
27
28
29
30
31
32
TITLE
CHAP
11
12
13
14
15
23
24
25
26
31
RETURN
9
10
DISPLAY
CH/TRK
15
1
22
23
24
+
VOL
14
Front Panel Display
INPUT SEL.
VIEW
7
9
10
11
12
13
CLEAR
0
100+
19
20
21
9
ZOOM
TV MUTE
DVD
1
2
3
4
5
6
AUDIO
7
1
3
SCREEN FIT
5
6
7
8
33
8
9
1
2
3
The DVD Deck is active
A DVD, CD, VCD, or SVCD is loaded
The number to the right of the “TITLE” symbol is
the current title number
4
The time, counter position, time remaining or
current deck status is displayed
VHS tape is inserted
Recording is in progress (normal and timer)
The VCR Deck is active
3D Sound is active
5
6
7
8
10
12
POWER (p.14)
SCREEN FIT (p. 34)
SHUTTLE <</>> (p.44)
MODE (p.41, 42)
REPEAT (p.38, 39, 44)
ZOOM (p.36), TV MUTE (p.12)
3D SOUND (p.43), 100+ (p.16)
DVD (p.14)
DIGEST (p.37)
F.ADV/SKIP (p.33, 44)
VOLUME +/– (p.12)
REWIND (p.33, 44)
SKIP BACK (p.33, 44)
STOP (p.33)
RECORD (p.47)
UP (p.16)
LEFT (p.16)
SETUP (p.16)
ENTER (p.16)
RETURN (p.16)
TITLE (p.34)
SP/SLP (p.49)
OPEN/CLOSE (p.14, 15)
TV/VCR (p.16)
0-9 (p.16)
AUDIO (p.39)
ANGLE (p.36)
INPUT SEL. (p.47)
CLEAR (p.40, 41, 42)
VCR, TV SELECT (p.14)
DISPLAY (p.16, 35)
CHANNEL œ/❷ (p.12, 16)
TRACKING œ/❷ (p.44)
FAST-FORWARD (p.33, 44)
SKIP NEXT (p.33, 44)
DISC MENU (p.34)
PLAY/PAUSE (p.14, 15)
RIGHT (p.16)
DOWN (p.16)
MARK (p.40)
SEARCH (p.46)
SUBTITLE (p.37)
TIMER (p.50)
9 A DVD with a DTS soundtrack is loaded
10 The number to the right of the “CHAP” symbol is
the current chapter number
11 The Hi-Fi track of a VHS tape is playing
(The current TV show or video is broadcast in
Stereo)
12 A Timer Recording is programmed or in progress.
If blinking there is an error.
Also displays without the clock hands to indicate
that a recording is in progress, and blinks when
the VCR is in Pause mode.
Insert Remote Control Batteries
• Remove the battery cover by pushing down on the thumb tab and
sliding the cover.
• Insert two 1.5V “AA” batteries as shown, paying attention to the correct
polarities (+/–).
• When finished, slide the cover until it clicks back into place.
11
00044A DVD-V7070/AFR-Eng1
3/21/03 2:29 PM
Page 12
Using the TV Buttons on the Remote Control
POWER
OPEN/CLOSE
1
2
5
7
In this section, you will connect the DVD-VCR to your television
and run Auto Setup, which automatically searches for channels and
sets the player’s internal clock.
To determine whether your television is compatible, follow the instructions
below.
NOTES:
Switch your television on.
TV/VCR
2
Point the remote control towards the television.
AUDIO
3
Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
6
8
9
ZOOM
1
CLEAR
TV MUTE
INPUT SEL.
0
100+
DVD
2
SELECT
VCR
3
TV
VIEW
+
DIGEST
DISPLAY
VOL
F.ADV/SKIP
CH/TRK
-
3
DVD
VCR
SELECT
TV
VIEW
Brand
Codes
Brand
Codes
SAMSUNG
SHARP
SONY
RCA
TOSHIBA
PANASONIC
JVC
HITACHI
MITSUBISHI
NEWSAN
01, 14, 15, 23
02, 16, 22
03
07, 29
09
12, 24
11
10
13
27
LOEWE
ZENITH
LG
MAGNAVOX
EMERSON
SANYO
DAEWOO
NOBLEX
TELEFUNKEN
28
17
06, 08, 18
04
21
05, 20
19
25
26
2
+
DISPLAY
VOL
F.ADV/SKIP
Result:
CH/TRK
If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
-
➢
4
REC
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
DISC MENU
☛
7
8
9
ZOOM
3
TV MUTE
INPUT SEL.
0
100+
DVD
CLEAR
5
VCR
SELECT
TV
When you change the batteries in the remote control, you
must reprogram the code, following the same procedure.
You can then control the television using the following buttons.
Button
Function
POWER ➀
Used to switch the television on and off.
VIEW
DIGEST
+
DISPLAY
VOL
F.ADV/SKIP
CH/TRK
INPUT
-
➁
4
➂
CH (œ or ❷)
➃
Used to adjust the volume of the television.
Connect DVD-VCR to TV
2
2
To TV’s Antenna Input
3
Plug In DVD-VCR
Turn On DVD-VCR
Press the POWER button on the remote control or on the
DVD–VCR’s front panel.
Used to select an external source.
VOL + or –
DVD & VCR
Connect the DVD-VCR power cord to a standard 100V-240V,
50/60Hz wall outlet. Don’t press any buttons on the DVD-VCR or
remote during auto setup. “AUTO” blinks while the DVD-VCR runs
an auto setup procedure, where it will automatically search for all
active channels and set the clock. When Auto setting has been
completed, the front panel displays the current time. If Auto Clock
set is unable to find a channel to set the clock, you can set the
clock manually; See page 18.
ANGLE
3D SOUND
From Antenna or Cable
Connect Antenna/Cable to DVD-VCR
Choose one of the following methods to connect the DVD-VCR to
your TV:
RF Connection
Connect the supplied RF antenna cable from the OUT (TO TV) jack
on the back panel of the DVD-VCR to your television’s Antenna
Input.
NOTE : Check the channel to connect DVD-VCR to your
television’s Antenna Input; See page 22.
Line Connection
Connect an RCA-type audio/video cable (red, white, yellow) from
the LINE OUT jacks on the back panel of the DVD–VCR to your
television’s Line In jacks. Use red for right audio, white for left
audio, and yellow for video.
NOTE: It is recommended that you use the Line Connection if your
TV is equipped with RCA jacks.
4
DIGEST
1
Connect the RF antenna cable from your indoor/outdoor antenna or
cable wall outlet to the IN (FROM ANT.) jack on the back panel of
the DVD-VCR.
ANGLE
3D SOUND
DVD & VCR
• Advanced Connections are covered in Appendix A.
• Even if you plan to use the S-Video or Component Video Outputs,
you MUST connect the DVD-VCR to your television with
either the standard RF or the Line Out connection. This
enables you to operate the DVD-VCR setup menus.
1
SHUTTLE
4
Your VCR remote control will work with Samsung televisions and
compatible brands.
3
SCREEN FIT
MO D E/
REPEAT
Basic Connections/Auto Setup
5
Press the POWER button on your TV.
Used to select the required channel.
POWER
Turn On TV
4
POWER
2
SCREEN FIT
MUTE
➄
➢
12
Used to toggle the sound on and off.
6
Set TV to Channel 3, 4 or Line
Be sure to use the same channel you selected in Step 2. If you
used the Line Connection, set your TV to its Line Input.
SHUTTLE
4
MODE/
REPEAT
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
4
5
7
8
ZOOM
3D SOUND
13
CL
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 14
Deck Control Buttons
The DVD-VCR uses one set of controls to operate both decks. The
following buttons are helpful in successfully controlling each deck.
1
POWER
POWER Button
Basic VHS Playback
To play a videotape, simply insert it in the VHS deck and press the
Play button. Tapes without Record Safety Tabs can be set to play
automatically when inserted; see page 45.
Press the POWER button on the remote control or front panel to
turn on the DVD-VCR.
OPEN/CLOSE
1
2
1
2
Press the DVD button on the remote control or front panel when
you want to control the DVD deck.
• The DVD indicator will light on the Front Panel Display to show
that the DVD deck is selected.
3
SCREEN FIT
TV/VCR
SHUTTLE
5
4
MODE/
REPEAT
DVD Button
6
2
8
3
9
ZOOM
CLEAR
INPUT SEL.
0
100+
DVD
VCR
4
SELECT
VCR Button
Press the VCR button on the remote control or front panel when
you want to control the VCR deck.
• The VCR indicator will light on the Front Panel Display to show
that the VHS deck is selected.
ANGLE
3D SOUND
TV MUTE
TV
VIEW
2
3
+
DIGEST
F.ADV/SKIP
4
DISPLAY
VOL
3
OPEN/CLOSE
EJECT
DVD
4
Eject Tape
1
CHANNEL
REC
.... SELECT .... VCR
VIDEO
Press the OPEN/CLOSE button on the remote control or the
EJECT button on the front panel.
INPUT SEL. Button
Press the INPUT SEL. button repeatedly to cycle through all of
your input sources, including the Tuner (Ch##), Line 1 (rear AV
input), and Line 2 (front AV input).
• It is only available when VCR deck is selected.
Stop Playback
Press the ■ (Stop) button on the remote control or front panel.
CH/TRK
-
Play Tape
Press the ❿ll (Play/Pause) button on the remote control or front
panel. If the tape is missing the Record Safety Tab and Auto Play
is turned on, the tape will begin to play automatically, see page 45.
AUDIO
7
Insert VHS Tape
Insert a standard VHS videotape into the VHS Deck.
• Power will turn on automatically when you insert a videotape.
5
LINE IN 2
Additional VCR Options
• For special VCR Playback features, see pages 44~45.
• For VCR Recording features, see pages 47~49.
• For Timer Recording features, see page 50.
DIGEST
+
DISPLAY
VOL
F.ADV/SKIP
CH/TRK
-
Basic DVD Playback
3REC
DISC MENU
2
Follow these instructions to playback a DVD.
1
OPEN/CLOSE
1
2
2
1
TV/VCR
6
AUDIO
+
OL
Insert Disc
Place the disc in the drawer with the label side of the disc facing
up. If the disc has two sides, orient the disc with the desired label
facing up.
3
SHUTTLE
5
SETUP
/ENTER
Open Disc Drawer
Press the OPEN/CLOSE button on the remote control or front
panel to automatically power on the DVD-VCR and open the disc
drawer.
OPEN/CLOSE
EJECT
DVD
.... SELECT .... VCR
4
CHANNEL
REC
VIDEO
L AUDIO R
LINE IN 2
3
Close Disc Drawer
Press the OPEN/CLOSE button on the remote control or front
panel to close the disc drawer.
DISPLAY
CH/TRK
-
4
Play the DVD
Press the ❿ll (Play/Pause) button on the remote control or front
panel.
• Many discs will begin playback automatically when the disc
drawer closes.
• If the DVD has a disc menu, or more than one title, the disc
menu may appear.
4
DISC MENU
4
5
Additional DVD Options
• For advanced DVD Setup options, see pages 24~31.
• For special DVD Playback features, see pages 33~43.
14
L AUDIO R
15
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 16
Basic TV Tuner Operations
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner.
2
Follow these steps to change the on-screen menu language to
English, French or Spanish.
REC
3
SCREEN FIT
5
4
MO D E/
REPEAT
1
6
1
7
8
9
ZOOM
2
ANGLE
3D SOUND
CLEAR
TV MUTE
DVD
SELECT
VCR
Channel Up/Down
Press to change to the next or previous channel.
INPUT SEL.
0
100+
TV/VCR
Press to switch between your TV’s tuner and the VCR’s internal
tuner.
AUDIO
3
TV
1
3D SOUND
INPUT SEL.
0
100+
DVD
VCR
SELECT
+
F.ADV/SKIP
5
2
Display
Press to display the channel you are watching.
• Also works in DVD and VCR mode.
DISPLAY
VOL
100+ Button
CH/TRK
5
-
SETUP
/ENTER
1
2
Set “Language”
Using the Up/Down and Left/Right buttons, move the selection
arrow to “Language/Idioma/Langue,” then press ENTER button.
0-9 Buttons
Press to select channels 100 and higher. First, press the 100+
button, then press the remaining digits using the 0-9 buttons.
TV
VIEW
DIGEST
4
CLEAR
TV MUTE
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
Press to select channels directly.
4
DISC MENU
TV/VCR
SHUTTLE
3
Menu Language
3
RETURN
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
Set menu Language
Move the selection bar to your desired Language, then press
ENTER button.
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Language/Idioma/Langue
2
œ❷➛❿
RETURN
ENTER
LANGUAGE/IDIOMA/LANGUE
❿ English
Español
Français
On-Screen Menu Navigation
RETURN
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
The on-screen menu system allows you to set all functions for your
DVD-VCR. The following buttons are used to open and navigate
through the on-screen menu system.
1
œ❷➛❿
RETURN
ENTER
The Setup Menu is the opening
screen of the on-screen menu
system
SETUP Button
2
DISC MENU
2
SETUP
/ENTER
2
MENU PRINCIPAL
3
4
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Up/Down and Left/Right
Moves menu selection cursor up, down, left and right to cycle
through menu options
ENTER Button
Press to confirm settings in certain menus.
REC
English Setup Menu
With the DVD in stop mode, press to access the DVD-VCR onscreen menu system.
DVD Setup
Language/Idioma/Langue
RETURN
œ❷➛❿
RETURN Button
Returns to the last menu viewed or exits the menu system.
2
4
TITLE
SUBTITLE
SPEED
TIMER
16
2
ENTER
French/Spanish Setup Menu
1,3
RETURN
ENTER
œ❷
MARK
SEARCH
17
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 18
Manual Clock Set
REC
DISC MENU
Tuner Band Setting
If Auto Setup was unable to find a local TV station to set the DVDVCR’s internal clock, follow these instructions to set the date/time
manually.
NOTE: It is important to set the clock for accurate Timer
Recording.
This feature allows you to manually set the DVD-VCR’s tuner band
to Antenna or Cable, whichever you connected to the Antenna In
jack during initial setup.
• Use this setting only if Auto Setup detected the incorrect tuner
band, i.e. channels are coming in on the wrong channel numbers.
REC
DISC MENU
SETUP
/ENTER
SETUP
/ENTER
1
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
2
3
VCR
Program
Option
Clock
4
Exit
œ❷➛❿
ENTER
•
•
•
•
•
CLOCK SET/ADJUST
Auto
5
❿ Manual
RETURN
œ❷ENTER
Set the Clock
Press LEFT/RIGHT to select each of the following options, then
press UP/DOWN to set each option:
Clock Set/Adjust
RETURN
Select “MANUAL”
Move the selection arrow to “MANUAL”, then press ENTER to turn
this feature “Off.”
• The “Set Clock Menu” will change as shown.
Language
Channel
Select “Clock”
Using the up/down and left/right buttons, move the selection cursor
to “Clock Set/Adjust,” then press ENTER to select.
MAIN MENU
DVD
1
With the DVD in stop mode, press the SETUP button.
1,3
RETURN
Open “SETUP MENU”
Set Hour – Set the hour using the up and down buttons.
Set Minute – Set the minute using the up and down buttons.
Set Month – Set the month using the up and down buttons.
Set Day
– Set the day using the up and down buttons.
Set Year – Set the year using the up and down buttons.
Confirm Settings
Press the RETURN button to save your clock settings and return to
the Setup menu.
• Press Return again to exit.
Open “SETUP MENU”
1
With the DVD in stop mode, press the SETUP button.
2
Select “Channel”
RETURN
Using the up/down and left/right buttons, move the selection cursor
to “Channel Setup”, then press ENTER to select.
3
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
Select “Ant/Cable”
Move the selection arrow to “Ant/Cable” then press right to select
from the following options:
• Antenna - Indicates that the DVD-VCR is connected to an indoor
or outdoor VHF/UHF antenna.
• Cable TV - Indicates that the DVD-VCR is connected to Cable TV.
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Channel Setup
œ❷➛❿
RETURN
CHANNEL SETUP
❿ Ant/Cable:
[Cable TV]
Auto channel memory
Channel add/delete
œ❷➛❿
RETURN
CHANNEL SETUP
CLOCK SET/ADJUST
❿ Ant/Cable:
TIME
12:00AM
DATE
1/01
YEAR
2002 TUE
œ❷➛❿
RETURN
18
ENTER
[Antenna]
Auto channel memory
Channel add/delete
œ❷➛❿
RETURN
19
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 20
Auto Channel Memory
Auto Channel Memory will automatically seek and store all active
channels in your area.
REC
DISC MENU
1
2
1,3
RETURN
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
SETUP
/ENTER
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
Select “Channel”
Using the up/down and left/right buttons, move the selection cursor
to “Channel Setup”, then press ENTER to select.
3
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Use this feature if Auto Channel Search missed a channel that you
would like to add, or added a channel you wish to remove.
1
• The DVD-VCR will automatically search for all available
channels in the selected Tuner Band. This procedure may take
a few minutes to complete.
• When finished, the lowest channel found will be displayed.
œ❷➛❿
ENTER
DISC MENU
Open “SETUP MENU”
SETUP
/ENTER
1,3
2
Select “Channel”
Using the up/down and left/right buttons, move the selection cursor
to “Channel Setup”, then press ENTER to select.
3
RETURN
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
Select “Channel add/delete”
Move the selection bar to “Channel add/delete,” then press ENTER
to select.
4
Select Channel to add/delete
Use the CH œ/❷ buttons to tune in the channel number you wish
to add or remove.
Channel Setup
RETURN
REC
With the DVD in stop mode, press the SETUP button.
Run “Auto channel memory”
Move the selection arrow to “Auto channel memory,” then press
ENTER to select.
MAIN MENU
Channel Add/Delete
5
Select “CHANNEL ADD/DELETE”
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Channel Setup
RETURN
œ❷➛❿
ENTER
Press right to add or press left to remove the channel from
your channel list.
• Repeat steps 4 and 5 to add or remove additional channels.
CHANNEL SETUP
Ant/Cable:
[CABLE TV]
❿ Auto channel memory
Channel add/delete
RETURN
œ❷
ENTER
CHANNEL SETUP
Ant/Cable:
[CABLE TV]
Auto channel memory
❿ Channel add/delete
œ❷ENTER
RETURN
CHANNEL ADD/DELETE
Memorizing
CH 07
. . . . . please wait . . . . .
Select channel :
and press [ ❿] to
press [ ➛] to
ADD
DELETE
CH œ❷
RETURN
20
[ 01]
21
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 22
RF Output Channel
1
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
œ❷➛❿
Open “SETUP MENU”
2
Select “Option”
ENTER
3
Select “RF Output Channel”
OPTION SETUP
4
➛ ❿ 3CH
Auto
Off
Press Return to change. A message will appear on your TV.
Then press ENTER to change.
5
MAIN MENU
2
Select “Option”
Using the up/down and left/right buttons, move the selection cursor
to “Option Setup,” then press ENTER to select.
3
Select “Auto Power Off”
Move the selection bar to “Option Setup”, then press right to
select from following options:
• Off – Auto power off is disabled.
• 1Hr – DVD-VCR will auto shut off 1 hour after the last button is
pressed.
• 2Hr – DVD-VCR will auto shut off 2 hours after the last button is
pressed.
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Option Setup
RETURN
œ❷➛❿
RETURN
œ❷
Front Panel Dimmer
You can set the Front Panel Display to be bright all the time, dim
all the time, dim during power off.
MAIN MENU
1
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
RETURN
œ❷➛❿
2
Select “Option”
Using the up/down and left/right buttons, move the selection cursor
to “Option Setup,” then press ENTER to select.
ENTER
3
Set “Panel Display”
Move the selection bar to “Panel Display,” then press right to select
from the following options:
OPTION SETUP
RF Output Channel
3CH
➛ ❿ Auto
Panel Display
Auto Power Off
Off
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
Option Setup
Auto
Bright
Dim
• Auto – Front Panel Display will dim automatically during
power off.
• Bright – Front Panel Display will be bright all the time.
• Dim – Front Panel Display will be dim all the time.
œ❷
RETURN
22
ENTER
OPTION SETUP
RF Output Channel
3CH
Panel Display
Auto
➛ ❿ Off
Auto Power Off
Change “TV Channel”
A message will appear on your TV. When the message disappears,
change your TV to channel 3 or 4 to match the RF output channel
of the player.
œ❷
RETURN
Change “RF Output Channel”
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
Using the up/down and left/right buttons, move the selection cursor
to “Option Setup,” then press ENTER to select.
Move the selection bar to “RF Output Channel”, then press right
to change.
RF Output Channel
Panel Display
Auto Power Off
1
With the DVD in stop mode, press the SETUP button.
Option Setup
RETURN
Auto Power Off
23
Off
1Hr
2Hr
00044A DVD-V7070/AFR-Eng2
3/21/03 2:30 PM
Page 24
Disc Menu Language
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Follow these steps to choose your preferred language for DVD disc
menus. The DVD-VCR will automatically default to the language
you choose if it is available on a given DVD.
œ❷➛❿
1
ENTER
Open “SETUP MENU”
1
2
Select “DVD”
2
3
Select “Disc Menu”
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
English
English
Automatic
Unlocked
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
With the DVD in stop mode, press the SETUP button.
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
Follow these steps to choose your preferred language for DVD
subtitles. The DVD-VCR will automatically default to the language
you choose if it is available on a given DVD.
MAIN MENU
DVD Setup
RETURN
Subtitle Language
3
Move the selection bar to “Disc Menu,” then press ENTER to select.
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
DVD Setup
RETURN
œ❷➛❿
ENTER
Select “Subtitle”
Move the selection bar to “Subtitle,” then press ENTER to select.
DVD SETUP
RETURN
4
œ❷ENTER
Set “Disc Menu Language” Preference
Move the selection bar to your preferred language for DVD disc
menus, then press ENTER to select.
4
Set “Subtitle Language” Preference
Move the selection bar to your preferred language for DVD
subtitles, then press ENTER to select.
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
English
English
Automatic
Unlocked
DISC MENU LANGUAGE
❿ English
RETURN
Français
Deutsch
Español
Italiano
Nederlands
Others
œ❷ENTER
SUBTITLE LANGUAGE
RETURN
œ❷ENTER
❿ Automatic
English
Français
Deutsch
Español
Italiano
Nederlands
Others
Audio Language
RETURN
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
RETURN
English
English
Automatic
Unlocked
œ❷ENTER
Follow these steps to choose your preferred language for DVD
audio soundtracks. The DVD-VCR will automatically default to the
language you choose if it is available on a given DVD.
1
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
œ❷ENTER
2
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
AUDIO LANGUAGE
3
Francais
Deutsch
Español
Italiano
Nederlands
Original
Others
RETURN
Select “Audio”
Move the selection bar to “Audio,” then press ENTER to select.
❿ English
4
Set “Audio Language” Preference
Move the selection bar to your preferred language for DVD audio
soundtracks, then press ENTER to select.
œ❷ENTER
24
25
00044A DVD-V7070/AFR-Eng2
3/21/03 2:31 PM
Page 26
Parental
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
DVD Setup
RETURN
œ❷➛❿
ENTER
Digital Output
Rating Control is a password protected system that allows you to
block playback of DVDs based on their content. The system uses an
eight level rating system.
• If you try to play a DVD that exceeds the selected rating, an error
message will appear.
• Not all discs are rated.
1
If your A/V receiver is equipped with a Dolby Digital decoder, your
DVD-VCR can output Dolby Digital 5.1 sound, but you MUST
enable this feature in the menu system to prevent damage to your
speakers.
NOTE:
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
RETURN
English
English
Automatic
Unlocked
2
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
3
Select “Parental”
Move the selection bar to “Parental,” then press ENTER to select.
œ❷ENTER
4
• No - Indicates that no password is required to view any DVD
disc or to change Rating Control options. No additional Rating
Control settings are necessary.
• Yes – Indicates that a password is required to view some DVD
discs and to view Rating Control options. The menu will change
as shown.
NOTES:
• The first time “Require Password” is set to “Yes,” you will be
prompted to enter a new password.
• If the “Enter Password” screen appears, then “Require
Password” has already been set to “Yes.” Please skip to Step 5.
PARENTAL
Use Password
➛❿ No
RETURN
ENTER
PASSWORD CHECK
5
VCR
Option
Language
Clock
Channel
Exit
DVD Setup
1
œ❷➛❿
2
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
3
Select “Audio Options”
Move the selection bar to “Audio Options,” then press ENTER to
select.
4
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
RETURN
Set “Digital Output”
Move the selection bar to “Digital Output” then press the right
button to select from the following options:
AUDIO OPTIONS
Digital Output
➛❿ PCM
DTS
off
Dynamic Compression
on
• PCM - To use your DVD/TV with an A/V receiver NOT equipped
with a Dolby Digital decoder.
• Bitstream – To use your DVD/TV with an A/V receiver equipped
with a Dolby Digital decoder.
RETURN
œ❷
Enter Password
Select “Rating Level”
Move the selection bar to “Rating Level,” then press ENTER to
select.
PARENTAL
7
Use Password ➛❿ Yes
Rating Level
1
Change Password
œ❷
RETURN
ENTER
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
œ❷
RETURN
26
English
English
Automatic
Unlocked
œ❷ENTER
PRESS 0-9
6
ENTER
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
Enter a 4-digit password using the 0–9 buttons on the remote
control.
• Write your password down, and keep it in a safe place in case
you need it to change your settings later.
Enter Password
____
RETURN
DVD
Program
RETURN
Select “Use Password”
Move the selection arrow to “Use Password,” then press the right
button to select from the following options:
Select “Bitstream” ONLY if you have connected a Dolby
Digital-equipped A/V receiver to the Digital Output
(optical or coaxial) on the DVD-VCR back panel.
MAIN MENU
Change Rating Level
Use the up/down to select one of the following ratings:
• Level 8 Adult
• Level 4
• Level 7
• Level 3
• Level 6
• Level 2
• Level 5
• Level 1 Kids Safe
All ratings above the level you select will also be blocked, e.g., if
you block Level 6, then Levels 7 and 8 will also be blocked.
Press ENTER to confirm your selection.
• If you forgot your password, press power on from a cold start
with no disc in the unit. Press the REW and F.F buttons
simultaneously on the front panel for 5 seconds. The “reset ok”
message will appear. Press the power button and the DVD-VCR
will go to the “Auto Setup” mode. (See page 13)
ENTER
27
PCM
Bitstream
00044A DVD-V7070/AFR-Eng2
3/21/03 2:31 PM
Page 28
Dynamic Compression
DTS
If your A/V receiver is equipped with a DTS decoder, your DVDVCR can output DTS digital sound, but you MUST enable this
feature in the menu system.
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
NOTE: Select “On” ONLY if you have connected a DTS-equipped
A/V receiver to the DIGITAL AUDIO OUT (optical or coaxial) on
the DVD-VCR back panel.
DVD Setup
RETURN
œ❷➛❿
1
ENTER
Open “SETUP MENU”
Dynamic Compression constrains the dynamic range, i.e. the
difference between the quietest and loudest passages of a DVD
soundtrack. This enables you to limit loud noises, such as
explosions, or raise the volume of quiet passages, such as
whispering, while watching a movie. This is convenient for viewing
movies late at night.
1
With the DVD in stop mode, press the SETUP button.
With the DVD in stop mode, press the SETUP button.
2
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
2
3
Select “Audio Options”
3
ENTER
4
4
Move the selection bar to “DTS,” then press right to select from the
following options:
AUDIO OPTIONS
Digital Output
PCM
➛❿ off
DTS
Dynamic Compression
on
RETURN
œ❷
28
Set “DTS”
Off
On
• off - To use your DVD/TV with an A/V receiver NOT equipped
with a DTS decoder.
• on – To use your DVD/TV with an A/V receiver equipped with a
DTS decoder.
Select “Audio Options”
Move the selection bar to “Audio Options,” then press ENTER to
select.
Move the selection bar to “Audio Options,” then press ENTER to
select.
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
DVD Setup
RETURN
œ❷➛❿
ENTER
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
English
English
Automatic
Unlocked
RETURN
Select “DVD”
Open “SETUP MENU”
MAIN MENU
Set “Dynamic Compression”
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
English
English
Automatic
Unlocked
RETURN
œ❷ENTER
Move the selection bar to “Dynamic Compression,” then press
right to select from the following options:
• On - The total dynamic range of the DVD soundtrack will be
compressed, so quiet passages will be louder and loud
passages will be softer.
• Off – The original dynamic range will be preserved.
AUDIO OPTIONS
Digital Output
PCM
DTS
off
Dynamic Compression ➛❿ on
RETURN
œ❷
29
On
Off
00044A DVD-V7070/AFR-Eng2
3/21/03 2:31 PM
Page 30
TV Aspect Ratio
Black Level
Set the aspect ratio (length x width) of your TV screen so the DVD
player will display movies at the appropriate size for your
television. Choose from standard, letterbox, or widescreen format.
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
œ❷➛❿
ENTER
3
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
English
English
Automatic
Unlocked
RETURN
œ❷ENTER
DISPLAY OPTION
TV Aspect
Black Level
Alt Video Out
Wide
Low
S-Video
RETURN
œ❷ENTER
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
2
DVD Setup
RETURN
1
Select “DVD”
The Black Level feature adjusts the reference level of black in the
video signal to one of two choices:
• Low - Standard NTSC black level. Yields consistent contrast
through all sources.
• High - Enhanced black level, for increased contrast during DVD
playback.
1
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
2
Set “Display Options”
3
Set “TV Aspect”
Option
Language
Program
Clock
Channel
Exit
DVD Setup
Set “Display Options”
Move the selection bar to “Display Options”, then press ENTER to
select.
4:3 Pan-Scan
RETURN
œ❷ENTER
English
English
Automatic
Unlocked
RETURN
4
œ❷ENTER
Set “Black Level”
Move the selection bar to “Black Level,” then press right to select
from the following options:
• Low - Standard NTSC reference Black Level for consistent
brightness/contrast across all sources.
• High – Enhanced Black Level for increased brightness/contrast
when viewing DVDs.
DISPLAY OPTION
TV Aspect
Black Level
Alt Video Out
Wide
➛ ❿ Low
S-Video
RETURN
œ❷
If you connected your DVD-VCR to your television using the
S-VIDEO OUT or COMPONENT VIDEO OUT jacks, you MUST set
the “Alt (alternative) Video Out” selection in the on-screen menu
system.
MAIN MENU
1
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
DVD Setup
RETURN
œ❷➛❿
2
3
DVD SETUP
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
Set “Display Options”
RETURN
Select “DVD”
Move the selection bar to “Display Options”, then press ENTER to
select.
4
ENTER
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
Select “Alt Video Out”
Move the selection bar to “Alt Video Out,” then press right to
select from the following options:
• S-Video – Indicates that you are using the S-VIDEO OUT jack on
the rear panel to connect to your TV.
• Component – Indicates that you are using the COMPONENT
VIDEO OUT jacks on the rear panel to connect to your TV.
30
Low
High
Alt Video Out
• The S-Video or Component Video connection is only for the
DVD player. The tuner and VCR will still be viewed through the
RF or line outputs.
❿16:9 Wide
ENTER
DVD SETUP
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
TV ASPECT
4:3 Letter Box
œ❷➛❿
RETURN
Select “DVD”
Using the up/down and left/right buttons, move the selection cursor
to “DVD Setup,” then press ENTER to select.
Move the selection arrow to “TV Aspect”, then press ENTER to
select from the following options:
• 4:3 Letterbox – This method displays the full width of the
widescreen movie on a standard 4:3 television. As a result,
black bars will appear at the top and bottom of the screen.
• 4:3 Pan-Scan – The familiar way of watching DVD and VHS
movies, this method selectively crops (by panning and scanning
to keep the most important part of the picture visible) wide
screen movies to fit a standard 4:3 television screen.
• 16:9 Widescreen – This method allows you to view the full 16:9
picture on a widescreen television.
VCR
With the DVD in stop mode, press the SETUP button.
Move the selection bar to “Display Options”, then press ENTER to
select.
4
Open “SETUP MENU”
MAIN MENU
DVD
English
English
Automatic
Unlocked
œ❷ENTER
DISPLAY OPTION
TV Aspect
Black Level
Alt Video Out
RETURN
Wide
Low
➛ ❿ S-Video
œ❷
31
S-Video
Component
00044A DVD-V7070/AFR-Eng2
3/21/03 2:31 PM
Page 32
A/V Receiver Connections
To take full advantage of the movie theater experience that DVD
offers, you may want to connect your DVD-VCR to a complete
Surround Sound system, including an A/V Receiver and six
Surround Sound speakers.
Before You Begin...
OR
To Digital Audio Input of an A/V
Receiver with a Dolby Digital
Decoder
Special Playback Features
During DVD/CD playback you can select from the following
special playback options. To resume normal playback, press the ❿ll
(Play/Pause) button.
TV MUTE
1
SELECT
VCR
• The picture will pause and the audio will mute.
• To resume playback, press the ❿ll (Play/Pause) button.
• If the player is left in Pause mode for 5 minutes, it will stop
automatically.
VIEW
DIGEST
F.ADV/SKIP
+
2
-
DISPLAY
CH/TRK
1
REC
2
1
• Optical
• Coaxial
• Use whichever connection is available on your A/V Receiver.
Frame Advance (Step)
While in Still mode, press the F.ADV/SKIP button on the remote
control to advance one frame at a time.
Digital Audio Out
Connect EITHER an optical cable OR a digital coaxial cable from
the DIGITAL AUDIO OUT jacks on the back panel of the DVD-VCR
to their corresponding Digital Audio Input jacks on your A/V
Receiver:
• Audio is muted during Frame Advance mode.
• Press ❿ll (Play/Pause) to resume normal playback.
NOTE: Frame Advance operates only in the forward direction.
3
TV
Still
Press the ❿ll (Play/Pause) button on the remote control during
playback.
VOL
• If your A/V receiver is equipped with a Dolby Digital Decoder,
you have the option to bypass the DVD-VCR’s built-in Dolby
Digital Decoder. Use the DIGITAL AUDIO OUT connection
below.
INPUT SEL.
0
100+
DVD
F.ADV/SKIP
REC
DISC MENU
-
Skip Forward/Back
SETUP
/ENTER
While a CD or DVD disc is in Play mode, press the Skip
Forward/Back (❿❿l / l➛➛) buttons on the remote control or front
panel to jump forward and backward through disc chapters/tracks.
• Skip Forward will jump to the next chapter/track.
• Skip Back will jump to the beginning of the current chapter/track.
• Press Skip Back again to jump to the beginning of the previous
chapter/track.
DISC MENU
3
DIGEST
+
DISPLAY
VOL
F.ADV/SKIP
CH/TRK
-
Search Forward/Back
While a disc is in Play mode, press and hold the Forward/Back
(❿❿ /➛➛) buttons on the remote control or front panel to visually
search forward/backward at 2X - 4X - 8X - 16X - 32X - 128X speed.
Press ❿ll (Play/Pause) button to resume normal speed.
REC
5
SETUP
/ENTER
4
Slow Motion
During playback, press the ❿ll (Play/Pause) button to Still the
image. Then use the Search Forward (❿❿ ) to play in slow motion at
variable speeds.
• Each press increases the slow motion speed playback to 1/8, 1/4
or 1/2 normal speed.
• Audio is muted during slow motion playback.
• Front Panel Slow Motion Buttons - Press and hold the Forward
buttons on the front panel to activate slow motion playback.
Press the ❿ll (Play/Pause) button to resume normal playback.
5
Stop/Resume
• Press the Stop button once to stop playback. To resume the
DVD/CD from the point where the disc stopped, press the ❿ll
(Play/Pause) button.
• Press the ■ (Stop) button twice to completely stop playback.
The next time you press ❿ll (Play/Pause), the disc will start over
from the beginning.
32
33
DISC MENU
3
00044A DVD-V7070/AFR-Eng3
3/21/03 2:32 PM
Page 34
Title/Chapter/Time Selection
Disc Menu Navigation
REC
Many DVDs feature their own menu systems, where you can select
Titles, Chapters, Audio Tracks, Subtitles, and special disc features,
such as movie trailers, and information on the cast. Use these
buttons to make selections in the Disc menus.
DISC MENU
2
If you press the DISPLAY button during DVD playback, you can
view the current Title, Chapter/Track, and counter position. You
can also use this screen as shortcut to select any Title,
Chapter/Track, or counter position on the disc.
SETUP
/ENTER
1
2
DISC MENU Button
1
Press to access the DVD’s Disc menu, if applicable.
RETURN
TITLE
SUBTITLE
MARK
2
Press œ, ❷ or ➛ , ❿ to navigate through DVD’s Disc menu
options.
• Press up, down, left and right to highlight menu choices.
2
3
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
REC
DISC MENU
Select Title
• The “TITLE” icon will light on the Front Panel Display, followed by
the current title number, hours, minutes, and seconds.
ENTER Button
Press to make your selections in the Disc menu.
RETURN
1
Press the up/down and left/right buttons to select Title, then press
ENTER to change among all available titles on the disc.
SETUP
/ENTER
3
DISPLAY
CH/TRK
-
View DVD/CD Display
Press the DISPLAY button on the remote control during DVD/CD
playback.
2
+
VOL
F.ADV/SKIP
1
2
VIEW
DIGEST
DVD
T : 01
➛❿
C : 02
0 : 01 : 09
4
4
TITLE Button
3
Select Chapter or Track
Press the up/down and left/right buttons to select Chapter or Track,
then press ENTER to change among all available Chapters/Tracks
on the disc.
Press to access the DVD’s Title menu, if applicable.
ENG 5.1CH
A
ENG
• The “CHAP” icon will light on the Front Panel Display, followed
by the current title number, hours, minutes, and seconds.
DVD
4
Press the up/down and left/right buttons to select the counter
position indicator, then use the number buttons (0-9) to enter the
desired counter position in the format HH:MM:SS (H = Hours, M =
Minutes, S = Seconds).
Then press ENTER to enter the desired counter position.
Screen Fit Playback
1
T : 01
C : 02
➛❿
0 : 01 : 09
ENG 5.1CH
A
ENG
SCREEN FIT Button
During play, press SCREEN FIT button on the remote control.
• Allows you to eliminate the black bars in the top and bottom of
the screen when a movie is playing in the Widescreen
format (16:9).
• Screen Fit will not work when the Zoom mode is active.
(you can not remove the black bars on the screen) However,
Zoom mode will work when Screen Fit is active.
➢
34
Select Counter Position
DVD
T : 01
C : 02
0 : 01 : 09
ENG 5.1CH
A
ENG
◆ Various aspect ratios are available only in multiple
screen format discs.
◆ This function does not work when a DVD has been
recorded in a multi-camera angle format.
◆ On some DVDs, the black bars cannot be eliminated
due to their aspect ratio.
35
00044A DVD-V7070/AFR-Eng3
3/21/03 2:33 PM
Page 36
Zoom
7
8
Subtitle
You can zoom in at 2 or 4 times the normal magnification while
watching a DVD.
9
ZOOM
ANGLE
3D SOUND
CLEAR
TV MUTE
1
VCR
1
SELECT
TV
+
DIGEST
Open Zoom Magnifying Glass
During Playback or STILL mode, press the ZOOM button to display
the “Magnifying Glass icon” on the screen.
VIEW
1
Open Subtitle Menu
RETURN
During playback, press the SUBTITLE button.
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
1
DISPLAY
VOL
F.ADV/SKIP
SETUP
/ENTER
INPUT SEL.
0
100+
DVD
Many DVDs provide subtitles in one or more languages. The
SUBTITLE button provides a shortcut to view and select these
options.
CH/TRK
2
-
Position Magnifying Glass
Use the œ, ❷,➛, ❿ buttons to move the magnifying glass to any
2
Set Subtitle Language
Press the up/down buttons to select among all available subtitle
languages.
position on the screen you want to zoom.
• Subtitle languages are often represented by abbreviations.
3
Zoom In
Press the ENTER button repeatedly to zoom in at 2X - 4X - 2X and normal magnification.
A
3
Activate Subtitles
Press the left/right buttons to turn subtitles On or Off.
• The default subtitle setting is Off.
• Press the ENTER button to confirm your selection.
A
Angle
MO D E/
REPEAT
4
5
6
7
8
9
Some DVDs allow you to view the same scene from
different perspectives, or angles, while watching a
movie. Press the ANGLE button to activate this feature.
AUDIO
ZOOM
Digest Playback
DVD
3D SOUND
TV MUTE
CLEAR
1
INPUT SEL.
0
100+
DVD
1
SELECT
VCR
TV
1
+
VOL
Check for Angle Marker
DISPLAY
CH/TRK
2
DIGEST Button
During playback, press the DIGEST button.
• You’ll see the 9 individual windows representing each of the
chapters on the TV screen.
• When each window is displayed, the first 3 seconds of the
chapter will be played.
If multiple Angles are available on the DVD, the Angle mark will
appear on the screen during playback.
VIEW
DIGEST
VCR
SELECT
View Angle Options
If the Angle mark is present, press the ANGLE button to view the
Angle Selection menu.
2
DIGEST
+
VOL
F.ADV/SKIP
DISPLAY
CH/TRK
-1
DISC MENU
REC
Set DIGEST
Press the up/down buttons and left/right buttons or NUMBER
button to select the window you’d like to see, and press ENTER.
3
Select Screen Angle
• Up to 9 windows(chapters) can be displayed on the screen at a
time. Press ❿❿ for the next 9 chapters if the movie has more than
9.
Press the up/down buttons to select one of the available screen
angles.
➢
◆ You can start playback of the DVD player from the
desired chapter.
Skip button
◆ ‘DIGEST’ may not operate depending on the disc in
use.
36
TV
VIEW
ANGLE
37
00044A DVD-V7070/AFR-Eng3
3/21/03 2:33 PM
Page 38
A-B Repeat
2
3
SCREEN FIT
TV/VCR
SHUTTLE
5
4
MO D E/
REPEAT
Repeat Chapter/Title
The A-B Repeat function allows you to repeat any segment of a
DVD or CD. Simply mark the beginning point (A) and the ending
point (B) of the segment you want to review.
6
You can repeat a single chapter, or repeat a complete title.
2
1
AUDIO
7
1
ZOOM
8
1
9
ANGLE
3D SOUND
TV MUTE
100+
DVD
INPUT SEL.
0
SELECT
Select A-B Repeat Function
• “A-” will highlight when A-B Repeat is selected.
TV
2
Mark the Starting Point
Select “Chapter”
Press the left/right buttons to select “Chapter”.
• “Chapter” will highlight when Chapter Repeat is selected.
3
4
5
6
7
1
3D SOUND
8
9
100+
0
M OD E /
REPEAT
AUDIO
TV MUTE
DVD
ANGLE
CLEAR
VCR
VIEW
Repeat Chapter
Press the ENTER button to repeat the current chapter/track.
Press the ENTER button at the beginning of the segment you want
to repeat (Point A).
• “B” will highlight after Point A is selected.
NOTE: The minimum AB Repeat time is 5 seconds.
TV/VCR
SHUTTLE
ZOOM
2
NOTE: If you are playing a CD, the menu will display “Track” in
place of “Chapter”
VIEW
4
Select “Title”
Press the left/right buttons to select “Title”.
• “Title” will highlight when Title Repeat is selected.
3
Mark the Ending Point
Press the ENTER button again at the end of the segment you want
to repeat (Point B).
5
Repeat Title
Press the ENTER button to repeat the title.
• The segment will begin repeating in a continuous loop.
4
Cancel A-B Repeat
Press the REPEAT button to open the Repeat Menu, press
left/right to highlight “Off,” then press the ENTER button.
Audio
Many DVDs provide multiple language and audio setup options,
such as Dolby Digital 5.1, Dolby Pro Logic, or LPCM 2 Channel
audio. The AUDIO button provides a shortcut to view and select
among all available options for a given disc.
1
Open the Audio Menu
During playback, press the AUDIO button on the remote control.
2
Select DVD Audio Track
Press the up/down buttons to select the desired language/audio
setup on the DVD.
• Languages are represented by abbreviations; i.e. “ESP” for
“español.”
38
3
SCREEN FIT
• The current Repeat Mode will highlighted.
In Play mode, press the REPEAT button, then press left/right to
select A-B Repeat.
CLEAR
VCR
Open Repeat Menu
In Play mode, press the REPEAT button to open the Repeat menu.
39
INPUT SEL.
SELECT
TV
00044A DVD-V7070/AFR-Eng3
3/21/03 2:33 PM
Page 40
Bookmarks
Programmed Playback
You can insert up to three Bookmarks on your DVDs, so you can
jump quickly to your favorite scene or song.
Programmed Playback lets you set a custom order for playback of
chapters/tracks on a DVD or CD.
2
3
SCREEN FIT
TV/VCR
SETUP
/ENTER
SHUTTLE
1
Open Bookmark Menu
1
During playback, press the MARK button on the remote control.
The “Mark” header will appear on the screen.
RETURN
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
Open Playback Mode Menu
MODE/
REPEAT
4
5
6
7 1
8
9
AUDIO
While in Stop mode, press the MODE button.
ZOOM
ANGLE
3D SOUND
CLEAR
TV MUTE
1
2
Select Bookmark Placeholder
2
• The selected placeholder will highlight.
3
3
4
Play Bookmark
•
•
•
•
•
During playback, press the MARK button on the remote control.
Press the left/right buttons to move to a previously set bookmark.
Press the Play/Pause button to play the bookmark.
Press the CLEAR button to cancel the bookmark.
Press the MARK button again to exit the Bookmark menu.
Program Playback Order
Use the up/down and left/right buttons to select the remaining
chapters/tracks, pressing Enter after each.
• You can continue setting up to three bookmarks.
• When finished, press the MARK button to exit.
• Depending on the disc, the bookmark function may not work.
4
DVD
SELECT
TV
PROGRAM 01
Chap. (T:01)
01
05
09
13
02
06
10
14
03 04
07 08
11 12
15 16 ❿
œ❷➛❿
RETURN
CLEAR
Program Order
01 - - - - - -- -- -- --- -- -- --- -- -- --- -- -- -ENTER
PLAY
• Press the CLEAR button to change selections.
5
Play Revised Order
Press the ❿ll (Play/Pause) button. The disc will play back in the
custom programmed order.
• While in playback mode, press the CLEAR button on the remote
control to cancel Programmed Play.
PROGRAM 01
Chap. (T:01)
01
05
09
13
02
06
10
14
03 04
07 08
11 12
15 16 ❿
œ❷➛❿
RETURN
40
VCR
VIEW
Select Chapter/Track
Press the up/down and left/right buttons to select the first
chapter/track in your revised playback list, then press the ENTER
button.
Set the Bookmark
Play the DVD to the scene you want to bookmark, then press the
ENTER button. The placeholder will change to a number (1, 2 or
3).
Select “PROGRAM”
Using the left/right buttons, move the selection bar to “PROGRAM”
then press ENTER to select.
Press the left/right buttons to move to one of the three bookmark
placeholders (- - -).
INPUT SEL.
0
100+
CLEAR
41
Program Order
01
-- --- -- -- --- -- -- --- -- -- --- -- -- -ENTER
PLAY
00044A DVD-V7070/AFR-Eng3
3/21/03 2:33 PM
Page 42
Random Playback
3D Sound
DVD Random Playback lets the DVD-VCR set a random order for
playback of chapters/tracks on a DVD or CD.
3D Audio is an enhanced audio mode that creates the illusion of
Surround Sound with only two speakers.
7
1
Open Playback Mode Menu
In Stop mode, press the MODE button.
PROGRAM
1
RETURN
œ❷
• The disc will playback automatically in random order.
ENTER
3
Open 3D Sound Menu
During playback of a DVD, press the 3D SOUND button on the
remote control.
Select “RANDOM”
Using the left/right buttons, move the selection arrow to “Random
Play,” then press ENTER to select.
ANGLE
CLEAR
1VCR
DVD
DIGEST
2
Set 3D Sound
Press the up/down buttons to set “3D Sound” On or Off, then press
the 3D SOUND button to confirm your selection.
+
1
CH/TRK
-
Cancel Random Play
2
RETURN
œ❷
Insert Disc
Insert a CD-R with MP3 files into the DVD deck.
• The MP3 main menu will appear after a few seconds and the
first song on the disc will begin playing.
~
~
song1
Select Folder
Press the up/down buttons to select the folder on the CD-R which
contains the MP3 files you want to hear, then press Enter to select.
ENTER
• If there are more than 8 folders on the disc, press RETURN to
view additional folders.
• If there are no folders on the CD-R, skip to Step 3.
MP3
~
song1
RETURN
œ❷
~
1 song 1
2 song 2
3 song 3
4 song 4
5 song 5
6 song 6
7 song 7
8 song 8 ❿
music c1
3
Select MP3 File
Press the up/down buttons to select the desired MP3 file.
• If there are more than 8 MP3 files in the selected folder, press
the left/right buttons to view additional MP3 files.
• File names are truncated to eight characters: the first six
characters of the song, plus an asterisk (*), then a number.
• Press the Return button to back up and select another folder.
ENTER
4
Play MP3 File
Press the ENTER button on the remote control to play the selected
song.
• While the song is playing, you can use the up/down buttons to
browse through other folders.
5
Stop MP3 Selection
Press the ■ (Stop) button on the remote control to stop playback.
* To ensure proper playback of discs burned from MP3 files, make sure
the files have been recorded at a bit rate of at least 128 kbps.
* If there are any gaps (blank data) on multi-session discs, you may
experience playback problems.
* On discs that are recorded with a Variable Bit Rate(VBR), e.g. from 32 to
320 kbps, the sound may cut in and out.
42
TV
DISPLAY
VOL
F.ADV/SKIP
MP3 is a popular music format which allows you to compress
music files up to 1/12 of their original size while retaining near CD
quality sound. Your DVD-VCR can playback MP3 files burned onto
a CD-R disc.
1 music c1
2 music c2
3 music c3
SELECT
VIEW
MP3 Playback
music c1
INPUT SEL.
0
100+
Press the CLEAR button on the remote control to cancel Random
Play.
MP3
9
3D SOUND
➛❿RANDOM
2
8
ZOOM
TV MUTE
43
00044A DVD-V7070/AFR-Eng3
3/21/03 2:33 PM
Page 44
Special VCR Playback Features
While a videotape is playing, you can enjoy a variety of special
playback features, including Still, Frame Advance, Skip, Repeat, and
more. Press the Play button again to resume normal playback.
PLAY
1
Auto Play
If you want your videotapes to play automatically when you insert
them, turn on Auto Play.
NOTE:
Only tapes that are missing the Record Safety Tab will
play automatically when inserted.
Still
From Play mode, press Play/Pause to still a single frame.
1
Open the “SETUP MENU”
With the DVD in stop mode, press the SETUP button.
0:00:00 SP
2
Frame Advance
From still mode, press SKIP/F.ADV to advance to the next frame.
Press the DISPLAY button to see the
current status of the VCR deck, as well
as the tape counter position and
record speed.
F.ADV/SKIP
3
-
REC
DISC MENU
3
2
From Play mode, press F.Forward (❿❿) or Rewind (➛➛ ) to
cue/review at two speeds:
• Picture Search — Press and release to advance the tape
forward or backward at 5 times normal speed.
• Jet Search — Press and hold to advance the tape forward or
backward at 7 times normal speed.
3
4
Skip
From Play mode, press Skip/F.ADV to cue ahead exactly 30 seconds.
Press Skip repeatedly up to 4 times to cue ahead 2 minutes.
5
Shuttle
Tape Length
Press the left button to select the video cassette length.
This information is usually printed on the tape box. The menu
cycles through: T120, T160 or T180. Once the type of cassette is
set, the VCR can display the amount of time remaining on the tape
when you press the DISPLAY button.
Repeat
From Play mode, Shuttle >> gradually increases the cue speed
from Double-Speed playback to Picture Search to Jet Search.
Shuttle << gradually slows down the tape, then goes into Slow
mode, Still mode, Reverse Picture Search and Reverse Jet Search.
DVD
VCR
Program
Clock
Option
Language
Channel
Exit
VCR Function Setup
RETURN
œ❷➛❿
5
Tape Length
Auto Play
Auto Repeat
T120
➛ ❿ On
Off
RETURN
Auto Repeat
In the VCR FUNCTION SET UP “ Auto Repeat” sets the VCR to
play a tape repeatedly [unless a tape control is activated (stop, fast
forward or rewind)].
Tracking
DVD
SELECT
VCR
DIGEST
+
VOL
F.ADV/SKIP
TV
1
VIEW
DISPLAY
The Tracking adjustment removes the white lines that sometimes
appear during playback because of slight differences in recording
decks. The TRK button will automatically align the recorded tracks
with the playback heads to solve this problem. You may also set
tracking manually.
S-VHS Playback
The DVD-VCR allows you to playback high quality S-VHS tapes.
CH/TRK
1
1
REC
DISC MENU
44
1
Adjust Tracking Manually
During playback, press the TRK œ or TRK ❷ buttons to move the
white lines out of the picture.
ENTER
VCR FUNCTION SETUP
4
From Play mode, press Repeat to review the last 5 seconds of tape
(SP mode).
6
MAIN MENU
Select “Auto Play”
Move the selection arrow to “Auto Play,” then press right to select
from the following options:
• On - The VCR will automatically begin playing a video tape
when it is inserted, as long as the safety tab of the cassette has
been removed.
• Off - Auto play is disabled.
3
SETUP
/ENTER
Select “VCR”
Using the up/down and left/right buttons, move the selection arrow
to “VCR Function Setup,” then press ENTER to select.
Cue/Review
Insert a S-VHS Tape
Insert an S-VHS tape into the VCR deck.
2
Start Playback
Press Play/Pause on the remote control to begin playback of the
S-VHS tape.
45
On
Off
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 46
Variable Search System
Scan and play:
press [➛] or [❿]
Go to [0:00:00]:
Press [œ]
End search:
Press [❷]
0:00:00 SP
Press the SEARCH button to display the search screen in the stop
mode. When a program is recorded, the starting point is given an
Index mark for easy location. However, the VHS Index Search
System (VISS) cannot recognize index marks made by old VCRs. If
the VCR has trouble finding a mark, it is probably because the
cassette was recorded on a VCR without VISS. If you want to index
two programs in a row, set your VCR to stop, then start recording
each program. Pause has no effect on index marks.
1
Be sure you videotape has a Record Safety Tab. If the tab
is missing, you can cover the opening with a small piece of
tape. Warning: Do not cover this opening unless you are
sure you want to record over the tape.
Before You Begin...
Go to 0:00:00 stop
2
End search
ZOOM
• Power on the DVD-VCR
• Power on the TV
• Set the TV to channel 3 or 4 .
1
Use this feature when you want to search for a blank position to
record a program on a cassette. While a cassette is stopped, press
down arrow button. The VCR will fast forward, searching for a
blank position, and then automatically stop at that position.
If the VCR reaches the end of the tape during end search, the tape
will be ejected.
46
NOTE:
• Press right arrow for forward scan or left arrow for reverse scan.
• The display will show “Scan and Play”.
• When an index mark is found, the VCR plays for about five
seconds.
• Press the PLAY button to view that program.
If you don’t press PLAY, the VCR automatically searches for the
next index, or until the end of the tape is reached.
Use this feature when you want to search for the 0:00:00 counter
position on a cassette. Press the CLEAR button at the point on the
tape where you want to set the counter to 0:00:00. Later, while a
cassette is stopped, press up arrow button. The VCR will rewind or
fast forward, searching for the 0:00:00 counter position, and then
automatically stop at that position.
3
You can record a TV show in progress by inserting a blank tape and
pressing the REC button. You can even add time in 30-minute
increments up to 4 hours by pressing the REC button repeatedly;
see page 49.
Scan and play
Use scan and play when you don’t know exactly where a program
is located on a cassette tape.
2
Basic Recording
ANGLE
3D SOUND
CLEAR
TV MUTE
INPUT SEL.
0
100+
DVD
VCR
SELECT
2
TV
VIEW
DIGEST
Insert Tape
+
DISPLAY
VOL
F.ADV/SKIP
Insert a blank VHS tape into the VCR deck.
• Make sure the tape is long enough to record the entire program.
To change the Recording Speed, see page 49.
3
CH/TRK
-
REC
DISC MENU
Select a Channel to Record
Use the 0–9 buttons or the Channel Up/Down arrow buttons to
select the desired channel, or press the INPUT SEL. button to
select Line 1 or 2 if recording from an external device connected to
the front or rear Line inputs, respectively.
1
E
EJEC
DVD
3
Start Recording
CHANNEL
Press the REC button on the remote control or front panel.
For options while recording is in progress, see “Special Recording
Features” on the next page.
➢
REC
.... SELECT .... VCR
VIDEO
L AUDIO
LINE IN 2
3
Recording from the DVD player to the VCR is not
possible.
47
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 48
Special Recording Features
DIGEST
While a recording is in progress, you can watch a different channel,
watch a DVD, or add recording time in 30-minute increments.
+
One-Touch Recording (OTR) allows you to add recording time in
30-minute increments up to 4 hours at the touch of a button.
DISPLAY
VOL
F.ADV/SKIP
One-Touch Recording (OTR)
CH/TRK
1
-
1
2REC
Pause/Resume Recording
Press the ❿ll (Play/Pause) button. Press REC again to resume.
DISC MENU
2
Stop Recording
RECORD
1
Follow the instructions on page 47 to begin recording.
2
Press the STOP button.
SETUP
/ENTER
3
2
3
TV/VCR
4
Watch a Different Channel
To Watch a DVD
• Record length 0:30 appears on the On-Screen Display and the
DVD-VCR will record for exactly 30 minutes.
3
SHUTTLE
MODE/
REPEAT
4
5
7
8
6
AUDIO
3
ANGLE
3D SOUND
100+
DVD
CLEAR
VCR
5
Record
Continue pressing REC to add recording time in 30 minute
increments up to 4 hours.
Add Recording Time
• The DVD-VCR stops recording automatically when the time has
elapsed.
INPUT SEL.
0
Add Recording Time
Insert a DVD in the DVD deck and press Play. The output will
automatically change to the DVD.
9
ZOOM
TV MUTE
Activate OTR
While in Record mode, press the REC button again to activate
One-Touch Recording (OTR).
Press the TV/VCR button on the remote to switch to your TV tuner,
then select a different channel on your television.
SCREEN FIT
Start Recording
07
SP
See One-Touch Recording (OTR) on the next page.
SELECT
length 0:30
TV
4
OPEN/CLOSE
POWER
Record Speed
You can slow down the recording speed from SP to SLP in order to
fit six hours of programming on a T-120 tape.
1
Start Recording
SETUP
/ENTER
Follow the Basic Recording instructions on page 47.
2
Set Record Speed
2
Press the SPEED button on the remote control to set the Record
Speed to one of the following options:
RETURN
TITLE
SUBTITLE
MARK
SPEED
TIMER
SEARCH
• SP – Standard Play, for best quality.
• SLP – Super Long Play, for maximum recording time (3 times
SP).
NOTE: The selected Record Speed will appear on the front panel
display and on-screen display.
Maximum Recording Time - SP vs. SLP
48
Tape Length
SP (Standard Play)
T-120
2 hrs
SLP (Super Long Play)
6 hrs
T-160
2hrs 40 mins
8 hrs
T-180
3 hrs
9 hrs
49
0:30
1:00
1:30
2:00
3:00
4:00
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 50
How to Set a Timer Recording
MAIN MENU
DVD
VCR
Option
Language
Program
Clock
Channel
Exit
Insert a blank tape with a Record Safety Tab into the VCR deck.
The Timer Recording Feature allows you to program up to 8 events
at a time to record up to a month in advance.
Set the TV to channel 3 or 4.
Before You Begin...
• Power on the DVD-VCR
• Power on the TV
Set Timer Recording
œ❷➛❿
RETURN
START
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
:
:
:
:
:
:
:
:
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
END
_
_
_
_
_
_
_
_
:
:
:
:
:
:
:
:
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
DATE
SPD
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
2
3
1
1
To S-Video Input on Your TV
Connect S-VIDEO OUT to TV
DVD Only
Connect an S-Video cable from the S-VIDEO OUT on the back
panel of the DVD-VCR to the S-Video Input on your television.
Select “Program”
Using the up/down and left/right buttons, move the selection cursor
to “Set Timer Recording,” then press ENTER to select.
2
Select Channel Number
2
Connect Component Video Out to TV
Connect a component video cable from the COMPONENT VIDEO
OUT (Y, Pb, Pr) on the back panel of the DVD-VCR to the
Component Video Input on your television.
Press right and up/down buttons to set the channel. Press the right
button to move to the next setting.
œ❷➛❿
RETURN
DVD Only
Open “SETUP MENU”
With the DVD in stop mode, press the SETUP button or press the
TIMER button.
_
_
_
_
_
_
_
_
The S-Video or Component Video connection is only for the DVD
player. The tuner and VCR will still be viewed through the RF or
line inputs.
You must follow the “Alt Video Out” instructions on page 31 to
activate your alternative (S-Video, Component) video selection.
You can choose EITHER S-Video OR Component, but NOT both.
If your television is equipped with S-Video or Component Video
inputs, you can enjoy superior video quality when watching DVDs
with your DVD-VCR.
ENTER
1
CH
S-Video/Component Video Connections (for DVD)
To Component Video Input
on Your TV
DVD Only
4
Set “Time/Date/Speed”
Repeat step 3 to set start time, end time, date and record speed.
Date can be set for one time, daily or weekly recording. See below.
5
Save “Timer Recording”
Press the RETURN button to complete programming of the timer
recording. Stop the VCR or turn the power off. The timer indicator
comes on the VCR. The VCR will automatically turn on and begin
recording at the time you set. To stop a timer recording, press the
POWER button or STOP button on the VCR.
6
3
Connect Audio Out (DVD only)
3
Connect RCA audio cables from the Left/Right Line Out jacks on
the back panel of the DVD/VCR to the Left/Right Audio Line In
jacks on your television.
• You must use these Line Out jacks when connecting the DVDVCR to your TV with the S-Video or Component Video Output.
• Please refer to “Alt Video Out” on page 31 to activate your
connection.
To Left/Right Audio Inputs
on Your TV
Auto Speed Select
If you are not sure the tape is long enough for timer program
recording in the SP tape speed, set the recording tape speed to
“AUTO”. Recording starts in the SP tape speed. If the tape length is
not long enough, the tape speed automatically changes from SP to
SLP.
7
Daily/Weekly Date Programming
Weekly [SUN’S~SAT’S]: You can record TV programs on the same
channel at the same time every week.
Daily [MO ❿ FR] : You can record TV programs on the same
channel at the same time every day Monday through Friday.
50
51
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 52
Stereo Connections
You can enjoy stereo sound when watching movies and TV shows by
connecting your DVD-VCR to your home stereo system or stereo
TV.
1
DVD & VCR
Connect DVD-VCR to Stereo
Connect RCA cables from the Line Out Left & Right Audio jacks on
the back panel of the DVD-VCR to the Auxiliary Inputs on your
stereo receiver. If you are using a stereo television, connect the
Video Output as well.
2
Monitor-style televisions offer improved sound and picture over
regular televisions because they receive the audio and video signals
directly from the DVD-VCR through the line inputs.
NOTE:
1
2
• If you still do not hear stereo sound after inserting Hi-Fi stereo
video tape, press the Audio button until “Hi-Fi” appears on the
on-screen display.
DVD & VCR
Connect VCR to Monitor TV
To Monitor TV Audio/Video Inputs
Set TV to Auxiliary Mode
Set your monitor TV to “Aux,” “Video,” or “Line.” Refer to your
monitor television owner’s manual for the correct setting.
Play a Tape
Insert a DVD or Hi-Fi stereo videotape in your system and adjust the
volume on your stereo receiver or television. You should hear the
audio through your stereo speakers.
A monitor television is not the same as a computer
monitor.
Connect RCA cables from the Audio/Video Line Out jacks on the
back panel of the DVD-VCR to the Audio/Video Line Inputs of your
monitor TV.
Set Stereo to Auxiliary Mode
Set your stereo receiver or television to “Aux” or “Tape,” whichever
selects the line input for your particular device.
3
Monitor TV Connections
3
Connection is Complete
NOTE: With this connection, the TV/VCR button has no effect. It is
as if the TV/VCR button were always set to VCR.
2
3
SCREEN FIT
TV/VCR
SHUTTLE
MODE/
REPEAT
4
5
6
7
8
9
AUDIO
ZOOM
ANGLE
3D SOUND
TV MUTE
100+
52
CLEAR
INPUT SEL.
0
53
3
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 54
Connecting Other Video Equipment
You can connect a wide variety of audio/video equipment to your
DVD-VCR, including:
• An additional VCR
• Laser Disc Player
• DVD Player
• Camcorder
• Satellite Receiver
• Video Game
Since all of these devices use essentially the same connections, they
will be described together.
DVD & VCR
TV Audio/Video Outputs of
External Device
7
8
1
ANGLE
3D SOUND
CLEAR
INPUT SEL.
0
100+
DVD
VCR
SELECT
TV
2,3
AUDIO
Inputs
Connect Device to DVD-VCR
Connect RCA cables from the Audio and Video Line Outputs of
your external device to the Audio and Video Line Inputs on the
front or back panel of the DVD-VCR.
9
ZOOM
TV MUTE
Technical Specifications
Outputs
VIDEO
2 Composite video inputs, RCA Connector, 75Ω, 1Vp-p
RF
Antenna or CATV Input, F-Connector, 75Ω
AUDIO
1 Stereo audio outputs, RCA Connector, -8dbm, 1.5KΩ
AUDIO (DVD only)
2 Digital audio outputs (1 optical, 1 coaxial)
1 Stereo audio outputs
VIDEO
1 Composite video output, RCA Connector, 75Ω, 1Vp-p
VIDEO (DVD only)
1 S-Video output, S-Connector, 75Ω, Y=1.0Vp-p,
C=0.286Vp-p
1 Component video output, 75Ω, Y=1.0Vp-p, Pb=0.7Vp-p,
Pr=0.7Vp-p
VIEW
DIGEST
+
DISPLAY
VOL
F.ADV/SKIP
3
CH/TRK
2
-
REC
Watch Device
Play your external device, then press the Input Sel. button until the
playback from LINE1 (rear panel inputs) or LINE2 (front panel
inputs) appears on your TV screen.
RF
Channel 3 or 4
VIDEO SYSTEM
1/2-inch VHS system, 4 rotary head helical scanning;
FM azimuth luminance;chrominance: converted sub system
phase shift
Record Device
AUDIO TRACK
Normal: 1 track; Hi-Fi: 2 track
PLAY/RECORD TIME
T-180 tape: SP 3 hours, SLP 9 hours
DISC MENU
3
First, play your external device. Next, press the Input Sel. button
until the playback from LINE1 (rear panel inputs) or LINE2 (front
panel inputs) appears on your TV screen. Then press Record on
the VCR deck.
4
VCR
FF/REW TIME
T-120 tape: <2 minutes
HEADS
Video: DA 4 rotary
Timer Record From Device
Audio: 2 rotary heads (Hi-Fi); 1 stationary head (Linear)
Select LINE1 (L1) or LINE2 (L2) as your record source in the Timer
Record menu. All other Timer Record settings should be set in the
usual manner.
Control:1 stationary head
Erase: 1 full track, 1 audio track
DVD
SYSTEM
54
2 Stereo audio inputs, RCA Connector, -8dbm, 47KΩ,
front and rear
WOW & FLUTTER
Less than 0.005% (Hi-Fi)
FREQ. RESPONSE
20-20,000 Hz (Hi-Fi)
DISC COMPATIBILITY
CD, CD-R, CD-R/W
DVD-Video, CD-Digital Audio (5” and 3.5”), CD-Video, MP3
files on CD-ROM
FREQ. RESPONSE
96/48 kHz Sampling: 4 Hz-22kHz
S/N RATIO
110 dB
DYNAMIC RANGE
96 dB
THD
0.003 %
POWER REQUIREMENT
100-240V AC, 50/60 Hz, 25 watts
ENVIRONMENT
41-104 F (5-40 C); 10%-75% humidity
WEIGHT
13.8 lbs.
55
00044A DVD-V7070/AFR-Eng4
3/21/03 2:34 PM
Page 56
ELECTRONICS
AK68-00044A