Download Toshiba owners manual SD-2107 user guide

Download Toshiba owners manual SD-2107 user guide
 "TOSHIBA a
SO
™ DIGITAL AUDIO
DVD VIDEO PLAYER
SD-2107
- OWNER'S MANUAI
79070182
9876103000A
WARNING The lightning flash with arrowhead symbol, within an equilateral triangle, is
RISK OF ELECTRIC SHOCK intended to alert the user to the presence of uninsulated “dangerous voltage”
DO NOT OPEN within the product's enclosure that may be of sufficient magnitude to constitute
AVIS RISQUE DE CHOC ELECTRIQUE NE a risk of electric shock to persons.
PAS OUVRIR
WARNING :
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE : na
COVER (OR BACK). NO USERSERVICEABLE to the presence of important operating and maintenance (servicing) instruc-
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert the user
tions in the literature accompanying the appliance.
WARNING:
CAUTION:
ATTENTION:
CAUTION:
FCC NOTICE:
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ,
POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU FOUD.
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner's manual carefully and retain for future
reference. Should the unit require maintenance, contact an authorized service location - see service
procedure.
Use of controls, adjustments or the performance of procedures other than those specified may result herein
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties
authorized by Toshiba, could void the user's authority to operate the equipment.
In the spaces provided below, record the Model and Serial No. located on the rear panel of your DVD video player.
Model No.
Serial No.
Retain this information for future reference.
Location of the required label
PRODUCT IS CERTIFIED BY THE MANUFACTURER
TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J
APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED
TOSHIBA AMERICA CONSUMER PRODUCT, INC
82 TOTOWA RD., WAYNE, NJ 07470, U.S.A.
or
PRODUCT IS CERTIFIED BY THE MANUFACTURER
TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J
APPLICABLE AT THE DATE OF MANUFACTURE.
MANUFACTURED
TOSHIBA OF CANADA, LTD.
191 McNABB ST., MARKHAM, ONTARIO, L3R 8H2, CANADA
IMPORTANT SAFETY INSTR
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND
THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard.
The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing.
This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1.
Read owner's manual
After unpacking this product, read
the owner's manual carefully, and
follow all the operating and other
instructions.
Power Sources
This product should be operated
only from the type of power source
indicated on the marking label. If
you are not sure of the type of
power supply to your home, con-
sult your product dealer or local
power company. For products in-
tended to operate from battery power, or other sources, refer
to the operating instructions.
3. Grounding or Polarization
This product may be equipped with
a polarized alternating current line
plug (a plug having one blade wider
than the other). This plug will fit into
the power outlet only one way. This
is a safety feature. If you are un-
able to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
. Ventilation
Slots and openings in the cabinet
are provided for ventilation and to
ensure reliable operation of the
product and to protect it from over-
heating, and these openings must
not be blocked or covered. The
openings should never be blocked
by placing the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper venti-
lation is provided or the manufacturer's instructions have
been adhered to.
mm 3
Heat
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including am-
plifiers) that produce heat.
Water and Moisture
Do not use this product near wa-
ter - for example, near a bath tub,
wash bowl, kitchen sink, or laun-
dry tub; in a wet basement; or
near a swimming pool and the
like.
Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol clean-
ers. Use adamp cloth for cleaning.
Power-Cord Protection
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them, pay-
ing particular attention to cords at
plugs, convenience receptacles,
and the point where they exit from
‘the product.
10.
Overloading
Do not overload wall outlets; ex-
tension cords, or integral
convenience receptacles as this
can result in a risk of fire or electric
shock.
Lightning
For added protection for this prod-
uct during storm, or when it is left
unattended and unused for long
periods of time, unplug it from the
wall outlet. This will prevent dam-
age to the product due to lightning
and power-line surges.
11.
12.
13.
14.
15.Burden
Object and Liquid Entry
Never push objects of any kind into
this product through openings as
they may touch dangerous voltage
points or short-out parts that could
result in a fire or electric shock.
Never spill liquid of any kind on the
product.
Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Accessories
Do not place this product on an
unstable cart, stand, tripod,
bracket, or table. The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product. Use only with a cart,
stand, tripod, bracket, or table rec-
ommended by the manufacturer,
or sold with the product. Any mounting of the product should
follow the manufacturer's instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
531254
Disc Tray
Keep your fingers well clear of the
disc tray as it is closing. It may
cause serious personal injury.
Do not place a heavy object on or
step on the product. The object
may fall, causing serious personal
injury and serious damage to the
product.
16.
17.
18.
19.
20.
Headphones
When you use the head-
phones, keep the volume at a
moderate level. If you use the
headphones continuously with
high volume sound, it may
cause hearing damage.
Disc
Do not use a cracked, de-
formed, or repaired disc. These
discs are easily broken and
may cause serious personal
injury and product malfunction.
Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the
product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in per-
formance - this indicates a need for service.
Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or otherhaz-
ards. Refer all servicing to
qualified service personnel.
Replacement Parts |
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
4 mm
Introduction )
Precautions
Notes on Handling
E When shipping the DVD video player, the original shipping
carton and packing materials come in handy. For maximum
protection, repack the unit as it was originally packed at the
factory.
Do not use volatile liquids, such as insect spray, near the
DVD video player. Do not leave rubber or plastic products
in contact with the DVD video player for a long time. They
will leave marks on the finish.
The top and rear panels of the DVD video player may
become warm after a long period of use. This is not a
malfunction.
When the DVD video player is not in use, be sure to
remove the disc and turn off the power.
If you do not use the DVD video player for a long period,
the unit may not function properly in the future. Turn on and
use the DVD video player occasionally.
Notes on Locating
HE When you place this DVD video player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD video
player away from the TV, radio, or VCR.
Notes on Cleaning
Use a soft, dry cloth for cleaning.
@® For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the DVD video
player.
@ If you use a chemical saturated cloth to clean the unit,
follow that product's instructions.
To Obtain a Clear Picture
The DVD video player is a high technology, precision device. If
the optical pick-up lens and disc drive parts are dirty or worn
down, the picture quality becomes poor. To obtain a clear
picture, we recommend regular inspection and maintenance
(cleaning or parts replacement) every 1,000 hours of use
depending on the operating environment. For details, contact
your nearest dealer.
Notes on Moisture Condensation
Moisture condensation damages the DVD video
player. Please read the following carefully.
Moisture condensation occurs, for example, when you pour a
cold drink into a glass on a warm day. Drops of water form on
the outside of the glass. In the same way, moisture may
condense on the optical pick-up lens inside this unit, one of
the most crucial internal parts of the DVD video player.
examples of moisture
condensation /
H Moisture condensation occurs during the
following cases.
@ When you bring the DVD video player directly from a cold
place to a warm place.
@ When you use the DVD video player in a room where you
just turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
O In summer, when you use the DVD video player in a hot
and humid place just after you move the unit from an air
conditioned room.
€ When you use the DVD video player in a humid place.
E Do not use the DVD video player when moisture
condensation may occur.
If you use the DVD video player in such a situation, it may
damage discs and internal parts. Remove the disc, connect
the power cord of the DVD video player to the wall outlet,
turn on the DVD video player, and leave it for two or three
hours. After two or three hours, the DVD video player will
have warmed up and evaporated any moisture. Keep the
DVD video player connected to the wall outlet and moisture
condensation will seldom occur.
Introduction )
Table of Contents
Introduction
E SAFETY PRECAUTIOÓNS ...................eeme... 1 E Identification of Controls ...................... 7-10
Ш IMPORTANT SAFETY Front Panel/Rear Panel/DVD display
Remote Control
INSTRUCTIONS auuaniserNarEn aaa 2-4 Preparing the Remote Control
EM Precautions ..............._.eeeerererernererercenee e 5 Operating with the Remote Control
Connections
E Connecting to atV .................ceemmeeeeeeneo 11 NM Connecting to Optional Equipment ... 13, 14
— IM Connecting to an Audio System.............. 12 Enjoying Dolby Digital (AC-3) Sound
Basic Playback
Enjoying Dolby Pro Logic Surround Sound
Enjoying 2 Channel Digital Stereo Sound
E Playing Back a Disc ....................e.e.... 15-18
Basic Playback
Playing at x2, x8 or x30 the Normal Speed
Playing Frame by Frame
Playing in Slow-Motion
Resuming Playback from the Same Location
Advanced Playback
H Locating a Specific Title, Chapter,
or TracK ees 19, 20
Locating a Title Using the Title Menu
Locating a Title
Locating a Specific Chapter or Track Directly
Locating a Specific Chapter or Track
Locating a Specific Location Within a Title
Repeating a Title, Chapter, or Track
Repeating a Specific Segment
E Playing in a Favorite Order ..................... 22
Setting Titles, Chapters, or Tracks in a Favorite Order
E Zooming a Picture ....................esseeeeeecee.. 23
Zooming a Picture
№ Selecting the Camera Angle ................... 24
Changing the Camera Angle
Function Setup
Selecting a Playback Audio Setting
№ Selecting Subtitles .......................eveem.. 26
Displaying Subtitles
Selecting a Subtitle Language
№ Using the On-Screen Display ................. 27
Checking the Operational Status
Checking the Remaining Time and Setting Status
M Customizing the Function Settings ......... 28
Displaying the SET UP MENU Screen
Setting the Audio Sound
Setting the Function Modes
Setting the Displays
Setting the Parental Lock |
Ш Table of Languages ......................eerecvee.. 37
Others
E Notes on Discs ................ene.e=.evermerezcccrne. 38 E LIMITED WARRANTY
Notes on Region Numbers DVD VIDEO PLAYER esse 41
E Before Calling Service Personnel ........... 39
E Specifications ..........................eeeeereeeeecene 40
6 NN
Introduction )
Identification of Controls
See the page in |) for details.
Front Panel / Rear Panel / DVD Display
Front Panel
~—— SKIP buttons
DVD display STOP button
PAUSE button
POWER indicator 15»
POWER button 15) PLAY button 15»
Disc tray (15) — — OPEN/CLOSE button [15
Rear Panel
— SVIDEO OUT jack (11) 12)
— VIDEO OUT jack 11) 12)
ps
и“
ANALOG AUDIO OUT (L/R) jacks [11 12) —
PCM/AC-3 DIGITAL AUDIO OUT jack [13)[14) ———
Power cord
H Pressing of the DIMMER button on the DIMMER Normal ——m Dimmed — Off
remote control changes the brightness of A |
the Display.
NN
Repeat playback mode indicators
Operating status indicator Audio CD indicator MEMORY indicator
Title number indicator
Chapter/track number indicator Total playing time/remaining time/elapsed time indicators
DVD indicator
M The indicators vary depending on the kinds of discs you play.
DVD Video disc Audio CD
* When closing the disc tray: * When closing the disc tray:
Example Example
Total number of titles Total number of Total playing time of
tracks the disc
* During playback: | During playback:
Exam le Example
Playing chapter 3 Elapsed time of Plavina track 6 Elapsed time of
g : ying
in title 2 the current title the current track
Some DVD video discs may not display the chapter
numbers or elapsed time.
Ш Other indicators
When playing back the
same title, chapter or
track repeatedly. 21)
When playing back a
specific segment
repeatedly. (A-B repeat)
21)
During memory
playback. [22>
— When playing back the
entire disc repeatedly.
21)
When the camera angle
can be changed.
When playback is
paused.
Angle icon indicator
8 mm
Introduction )
Identification of Controls (continued)
| The instructions in this manual describe the functions on the remote control. See the page in | > for details.
Remote Control
OPEN/CLOSE button (15)
SET UP button
TITLE button
Direction/CH (channel)/VOL (volume)
POWER button (15)
Г DISPLAY button 27)
buttons
RETURN button
RETURN
ANGLE button
ANGLE
CH
SUBTITLE ON/OFF button
MENU button*
SUBTITLE
ENTER
AUDIO
ENTER, TV button
AUDIO button 25)
SUBTITLE button
REV (fast reverse) button 17>
PAUSE/STEP button 17)
DIMMER button
ZOOM button 23)
MEMORY button 22)
REPEAT button ED
SKIP buttons
FWD (fast forward) button 17)
STOP button
LAST PLAY button
RPT C
LEAR
PLAY button 15)
SLOW button
CLEAR button
Number buttons
..Á-Ád— A-B RPT button 21)
> LL T button
* MENU button
Use the MENU button to display
the menu screen included on
DVD video discs. To operate a
menu screen, follow the
instructions in “Locating a Title
Using the Title Menu” .
Preparing the Remote Control
Insert the batteries into the remote control so you can use it to
operate the DVD video player.
Open the cover.
Make sure to match the + and — on the
batteries to the marks inside the battery
compartment.
Close the cover.
Notes on batteries
Improper use of batteries may cause battery leakage and corrosion.
To operate the remote control correctly, follow the instructions below.
e Do not insert the batteries into the remote control in the wrong
direction.
+ Do not charge, heat, open, or short-circuit the batteries. Do not
throw the batteries into a fire.
Do not leave dead or exhausted batteries in the remote control.
Do not use different types of batteries together, or mix old and new
batteries.
* If you do not use the remote control for a long period of time,
remove the batteries to avoid possible damage from battery
corrosion.
e |f the remote control does not function correctly or if the operating
range becomes reduced, replace all batteries with new ones.
* If battery leakage occurs, wipe the battery liquid from the battery
compartment, then insert new batteries.
* The batteries should last about one year with normal use.
Operating with the Remote Control
This section shows you how to use the remote control.
Point the remote control at the
remote sensor and press the
buttons.
Lo ЖК ооо а
30° >
Within about 7 m
!
Distance: About 7 m from the front of the
remote sensor
Angle: About 30° in each direction of
the front of the remote sensor
* Do not expose the remote sensor of the
DVD video player to a strong light source
such as direct sunlight or illumination. If
you do so, you may not be able to
operate the DVD video player with the
remote control.
To operate a Toshiba TV
You can use the CH A / V and VOL +/- buttons on this
remote control to operate a Toshiba TV.
ENTER While holding down TV button, press
CH A/V or VOL +/-.
Ch CH A/V :Toselectachannel 4 :up/ Y :down
т L vo. VOL+/: To adjust the volume
Point the remote control at the TV to operate.
* Some Toshiba TVs may not be compatible with this
remote control. |
* If you press the TV (ENTER) button while the DVD video
player is operating, playback may be interrupted. Be sure
to point the remote control at the TV when you want to
operate the TV.
* Direct the remote control at the remote sensor of the DVD video
player.
* Do not drop or give the remote control a shock.
* Do not leave the remote control near an extremely hot or humid
place.
* Do not spill water or put anything wet on the remote control .
* Do not open the remote controi.
10 =m
ConnectingtoaTV
Connect the DVD video player to your TV.
Connections) For details of output sound, see (25).
Connecting to a TV
Ш Setting of the output sound type
From the on-screen displays, set the “AUDIO OUT SEL." to “PCM”.
To wall outlet
Power plug
AUDIO OUT
ANALOG POM:AC-3 DIGITAL
2 L
L
Cumana | +
To S VIDEO OUT (yellow) ge (red) (white)
To VIDEO To ANALOG AUDIO OUT u)
OUT
S video cable (supplied) To S video input
If the TV has an S video input,
Audio/video cable (supplied)
To audio inputs
To video input (yellow) (red) (white)
eE)
connect the DVD video player with TV or monitor with
the supplied S video cable. When audio video inputs
using the S video cable there is no
need to connect the yellow video
cable.
* Refer to the owner's manual of the connected TV as well.
* When you connect the DVD video player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
* If your television set has one audio input, connect the DVD video player to a Y cable adapter (not supplied) and then connect to your
TV.
* Connect the DVD video player to your TV directiy. If you connect the DVD video player to a VCR, TV/VCR combination or video
selector, the playback picture will be distorted because DVD video discs are copy protected.
am 77
Connections) For details of output sound, see (25).
Connecting to an Audio System
You can listen to the sound of audio CDs and DVD video discs in stereo.
Connecting to an Audio System
H Setting of the output sound type
From the on-screen displays, set the “AUDIO OUT SEL” to “PCM”.
To wall outlet
Power plug
L
q +”
|
ed | < | — =
To S VIDEO UTE (yellow) A (white)
To VIDEO N J To ANALOG AUDIO OUT nm.
OUT
To audio inputs
of the amplifier
2 O
(white) Ojos: IO
La OE
c
‘са Ста
(red) = =
Audio system
Video cable To video input (yellow)
ei
S video cable (supplied) To S video input
If the TV has an S video input,
connect the DVD video player TV or monitor with
with the supplied S video cable. a video input
When using the S video cable
there is no need to connect the
yellow video cable.
Signal flow
Refer to the owner's manual of the connected equipment as well.
* When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall
outlet before making any connections.
* |f you place the DVD video player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD video
player away from the tuner and radio.
* The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
« Turn off the amplifier before you connect or disconnect the DVD video player's power cord. If you leave the amplifier power on, the
speakers may be damaged.
12
Connections )
For details of output sound, see [25).
You can enjoy the high quality dynamic sound of Dolby Digital (AC-3), Dolby Pro Logic, and 2 Channel Digital
Stereo.
Enjoying Dolby Digital (AC-3) Sound
Dolby Digital (AC-3)
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic
effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the
DVD video player to a 6 channel amplifier equipped with a Dolby Digital (AC-3) decoder or Dolby Digital (AC-3) processor. If you have a
Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-channel
Dolby Digital soundtracks, as well as from tities with the Dolby Surround mark. |
—
Ш Setting of the output sound type
* From the on-screen displays, set the
“AUDIO OUT SEL” to “AC—9”.
* Set the sound recording system
to “AC—3” on the audio setting
indication. (25)
L
VIDES OUT AUDIS OUT
ANALOG PEMIAC-3 DIGITAL
VIDEO A L A
ло? и
To PCM/AC-3 DIGITAL
т AUDIO OUT
» Signal flow
( Connection example x
Amplifier equipped with a Dolby Digital
(AC-3) decoder
Front speaker
Front speaker
4 N (left)
Standard equipment to
enjoy Dolby Digital (AC-3)
* The DVD video player
(equipped with an AC-3
output jack)
DVD video discs recorded
in Dolby Digital (AC-3)
6 channel amplifier
equipped with a Dolby
Digital (AC-3) decoder, or
Dolby Digital (AC-3)
speaker
= = NS Sub woofer
Rear speaker
>», (right surround)
Rear speaker
(left surround)
Vi
processor and power \_
amplifier
* 5 speakers and 1 sub Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby,” “AC-3,” “Pro
woofer Logic,” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
+ DO NOT connect the PCM/AC-3 DIGITAL AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital Receiver. This input
on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the PCM/AC-3 DIGITAL AUDIO OUT jack of the DVD video
player.
e Connect the PCM/AC-3 DIGITAL AUDIO OUT jack of the DVD video player to the “DIGITAL” or “COAXIAL input of a Dolby Digital Receiver or
Processor.
* Refer to the owner's manual of the connected equipment as well.
When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet
before making any connections.
* The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level.
Otherwise, the speakers may be damaged by a sudden high volume sound.
* Turn off the amplifier before you connect or disconnect the DVD video player's power cord. If you leave the amplifier power on, the speakers
may be damaged.
Em 73
Connecting to Optional Equipment
Warning
Do not set “AUDIO OUT SEL” to “AC-3” on the setting screen unless you are connecting (via the PCM/AC-3 DIGITAL AUDIO OUT
jack) an AV decoder that has the Dolby Digital (AC-3) decoding function. High volume sound may damage your hearing as well as the speakers.
Enjoying 2 Channel Digital Stereo Sound
Enjoying Dolby Pro Logic Surround Sound
Dolby Pro Logic Surround | | 2 Channel Digital Stereo
ou can dv 0 the dynamic realistic sound of Dolby ro dont You can enjoy the dynamic sound of 2 Channel Digital Stereo
urround by connecting an amplifier and speaker system (rig и: | ый he
and left front speakers, a center speaker, and one or two rear by connecting an amplifier equipped with a digital audio input
speakers) and speaker system (right and left front speakers).
= With an amplifier equipped with Dolby Digital (AC-3)
Connect the equipment the same way as described in
“Enjoying Dolby Digital (AC-3) Sound” 13) . Refer to that
amplifier's owner's manual and set the amplifier so you can
enjoy Dolby Pro Logic Surround sound.
= With an amplifier not equipped with Dolby Digital (AC-3)
Connect the equipment as follows.
Signal flow
[75 Q coaxial
cable
] N
í
Connection
To ANALOG example
1 AUDIO OUT To digital audio input
o O О Amplifier equipped with a
Г Audi bl Y 900000 digital audio input
udio cable
_—
To video
Connection ) input
o audio input
example
= Front speaker
(right)
Front speaker =
я. Amplifier equipped with
¿ p quipp (left)
| Dolby Pro Logic Surround
TV $” Front speaker
= (right) N J
~~
= =
—
Center speaker a
— connect one or two rear
speakers.
Rear speaker The output sound from the
rear speakers will be
monaural even if you
« connect two rear speakers.
№ Set “AUDIO OUT SEL.” to “PCM” via the on-screen HB Set “AUDIO OUT SEL. to “PCM” via the on-screen
displays. displays.
» Refer to the owner's manual of the connected equipment as well.
* When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making
any connections.
+ The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level. Otherwise, the
speakers may be damaged by a sudden high volume sound.
* Turn off the amplifier before you connect or disconnect the DVD video player's power cord. If you leave the amplifier power on, the speakers may be
damaged.
74 um
Basic Playback )
В CAUTION
- = Keep your fingers well clear of the disc tray as it is
ау! n g a C a | S C closing. It may cause serious personal injury.
POWER indicator DVD display STOP
7
8 ;
Hover me —
This section shows you the basics on how to play 1 3 2 4
back a DVD video disc or audio CD.
Basic Playback
E Preparations
* When you want to play back DVD video discs, turn on the TV and select the video input source connected to the DVD video player.
* When you want to enjoy the sound of DVD video discs or audio CDs from the audio system, turn on the audio system and select the
input source connected to the DVD video player.
* For connection details, see “Connections”. [11) —
* Set the playback picture size according to the aspect ratio of the connected TV via the on-screen displays. (33)
* |f you do not have the necessary equipment to enjoy Dolby Digital (AC-3) sound, set “AUDIO OUT SEL” to “PCM” via the on-screen
displays.
Press POWER.
The DVD video player turns on and the POWER indicator
on the player illuminates.
Press OPEN/CLOSE. '
You can open the disc tray by pressing this
The disc tray opens. button even if the DVD video player is turned
off.
Place the disc on the disc
tray.
* There are two different disc sizes. Place the
disc in the correct guide on the disc tray. If
the disc is out of the guide, it may damage
the disc and cause the DVD video player to
malfunction.
* Do not place anything except DVD video
discs or audio CDs on the disc tray.
y
With the playback side down —
Press PLAY.
You may need to press the TITLE or MENU
The disc tray closes and playback starts. button on the remote control to display the
menu screen depending on the DVD video
If you insert a DVD video disc that contains the title discs.
menu, the menu screen appears.
See “To start playback from the menu screen” :
* Do not move the DVD video player during playback. Doing so may damage the disc.
* Use the OPEN/CLOSE button on the remote control or DVD video player to open and close the disc tray. Do not push the disc tray while it is
moving. Doing so may cause the DVD video player to malfunction.
* Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD video player to malfunction.
mm 75
1
2
TITLE
MENU
A/Y/</>
ENTER
PAUSE/STEP
STOP
4
E To obtain a higher quality picture
Occasionally, some picture noise not usually displayed with a
normal broadcast may appear on the TV screen while playing —
back a DVD video disc because the high resolution pictures on
these discs include a lot of information. While the amount of noise
depends on the TV you use with this DVD video player, you should
generally reduce the sharpness adjustment on your TV when
viewing DVD video discs.
E About 2 CD
The WW ‚CD icons on the heading bar show the playable discs for
the function described under that heading.
PY” - You can use this function with DVD video discs
¿ED :You can use this function with audio CDs
To start playback from the menu screen
To stop playback
1 Press A/Y/</ > or the number buttons to
select the title you want.
2 Press ENTER.
ENTER — The DVD video player starts playback
from the selected title.
STOP
Press STOP.
The DVD video player returns to chapter
1 or track 1.
To remove the disc
OPEN/CLOSE
Press OPEN/CLOSE.
To pause playback (still mode)
PAUSE/STEP
Press PAUSE/STEP during
playback.
To resume normal playback, press the
PLAY button.
e The sound is muted during still mode.
Remove the disc after the disc tray
opens completely.
* Be sure to press the OPEN/CLOSE
button to close the disc tray after you
remove the disc.
In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen menu may damage your
television set, permanently etching that image onto its screen. To avoid this, be sure to press the STOP button on your remote control once the
movie is completed.
16 mm
Basic Playback )
Playing Back a Disc
(continued)
lil Gi Eid FWD
Fame, Slow- Last qe PLAY
by Frame Motion Play PAUSE/STEP
| О] | | | —
You can play back discs at various speeds, and resume playback from the
location where you stopped playback.
DvD, CD DVD
Playing at x2, x8 or x30 the Normal Speed Playing Frame by Frame
You can play back a disc at x2, x8 or x30 the normal speed. You can advance a DVD video disc frame by frame.
Press PAUSE/STEP during still
playback.
Each time you press the PAUSE/STEP
button, the picture advances one frame.
Press REV or FWD during playback.
* DVD video disc
The playback speed becomes x2 the
normal speed.
Each time you press the REV or FWD
button, the playback speed changes.
REV: Fast reverse playback
FWD: Fast forward playback
TV screen
х 2 х В х 30
— > —
4 +
x2 the x8 the x30 the
normal speed normal speed normal speed
* Audio CD
The fast reverse or fast forward playback
alternates between two speeds.
TV screen
FR1 FR2
Fast reverse playback
FF1 FF2
Fast forward playback
To resume normal playback
PLAY
mr Press PLAY.
The sound is muted during frame by frame playback.
scan reverse and forward of DVD video discs.
However, the DVD video player plays back sound during fast forward
or fast reverse playback of audio CDs.
e The x2 , x8 and x30 speeds are only approximate speeds. These
speeds may vary slightly from disc to disc.
mu 77
eR Set
PLAY
IY LT Gee OW
UU GE
О) © © ©
O O © ©
Py E и и
i в fai Pa
© © © ©
DVD
Playing in Slow-Motion
You can play back a DVD video disc in slow-motion.
Press SLOW during playback.
The playback speed becomes half the
normal speed.
Each time you press the SLOW button, the
slow-motion speed changes.
TV screen
1/2 1/8 1/16
1/2 the 1/8 the 1/16 the
normal speed normal speed normal speed
To resume normal playback
Press PLAY.
The sound is muted during slow-motion playback.
NETL
LE
Pd
Resuming Playback from the Same Location
You can stop playback and resume playback later from the
same location on the disc.
Press STOP at the location where
you want to interrupt playback.
* The DVD video player memorizes the
location where you stopped playback.
* The DVD video player stores that
location in its memory even if you turn
off the player.
Press LAST PLAY.
The DVD video player resumes playback
from the location where you stopped
playback.
* The Last Play function is canceled when:
— you unplug the DVD video player from the wall outlet after you
stop playback. ;
— you eject the disc.
— you adjust/change parental lock (35) or select a disc menu
language setting
* There may be a difference of the location where playback resumes
depending on the discs.
18 mm
Basic Playback )
+ DVD video disc >
«— Title 1 » | < Title 2
Chapter 1 Chapter 2| Chapter 1 Chapter2 Chapter 3
] | | | — | —
7 Vg
Id
y
DVD
Locating a Title Using the Title Menu
If a DVD video disc contains a title menu, you can locate a
specific title using the title menu function.
Press TITLE.
The title menu appears on the TV screen.
Example of a title menu
TITLE 2-2
Press A/ Y / </» to select the title
you want.
If the titles in the title menu are assigned a
number, you can directly locate a specific
title by pressing its assigned number with
the number buttons.
Press ENTER.
The DVD video player starts playback from
chapter 1 of the selected title.
* The instructions above describe the basic procedure. The
procedure varies depending on the contents of the DVD video disc.
If different instructions appear on the TV screen, follow those
instructions.
* |f you display the title menu during playback and press the TITLE
button again without selecting any title, the DVD video player
resumes playback from the point where you first pressed the TITLE
button.
_ “E
Locating a Specific Title, Chapter, or Track
-— Audio CD —
Track 1 Track 2 Track 3 Track 4 Track 5
| | | | |
SEINEN
Normally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Audio
CDs are divided into tracks. You can quickly locate any specific title, chapter, or track.
DVD
Locating a Title
If a DVD video disc contains title numbers, you can locate a
specific title by directly selecting a title number.
Press T.
Make sure that the space next to TITLE is
highlighted.
e.g.
Press the corresponding number
buttons for the title you want.
e.g. To select title 2
©
To select title 12
0-0
TITLE: E
CHAPTER: 1
TITLE: A
CHAPTER: 1
Press PLAY.
The DVD video player starts playback from
chapter 1 of the selected title.
* You can shift the highlight between next to TITLE and CHAPTER by
pressing A/V.
* Pressing the CLEAR button resets the TITLE and CHAPTER
numbers. To clear the TITLE, CHAPTER display, press the T button
several times.
* You can select a preferred language for on-screen displays. 33)
a
ad
TITLE
A/V/</ >
ENTER
SKIP
PLAY
CLEAR
Number buttons
T
Locating a Specific Chapter or Track Directly
If you know the chapter or track number you want to play, you
can locate it directly.
Press T.
Skip steps / and 2 if you are using an
audio CD.
e.g. DVD video disc
Press V to highlight the space next
to CHAPTER.
e.g. DVD video disc
TITLE: 1
CHAPTER: MI
Press the corresponding number
buttons of the chapter or track you
want.
You can use the button to select
numbers from 10 through 99.
e.g. To select chapter or track 25
[email protected]@-© |8Hir ee | roc
DVD video disc Audio CD
Press PLAY.
The DVD video player starts playback from
the selected chapter or track.
To select a title and chapter number at the same time
e.g. To select chapter 25 in title 2 |
O-0--,7 KONO RES
| —T
Title number Chapter number
TITLE: 2
CHAPTER: BEE
Pressing the CLEAR button resets the TITLE and CHAPTER
numbers. To clear the TITLE, CHAPTER display, press the T button
several times.
Press SKIP <q or P>»>l repeatedly
to display the chapter or track
number you want.
The DVD video player starts playback from
the selected chapter or track.
HE: To locate preceding chapters or tracks
- When you press the SKIP Hed button,
the DVD video player starts playback
from the beginning of the current chapter
or track.
When you press the SKIP I<« button
twice, the DVD video player starts
playback from the beginning of the
preceding chapter or track.
PP : To locate succeeding chapters or tracks
Some titles may not display the chapter number.
Locating a Specific Location Within a Title
You can locate a specific location by entering the time (hours,
minutes, seconds).
Press T twice.
TIME ml
Press the number buttons to enter
the time.
> 0-0-0-0-0
TIME PACO
Press PLAY.
The DVD video player starts playback from
the specified location.
Some discs may not respond to this locating.
20 mm
Advanced playback ) OT <_
Playing Repeatedly
PLAY
REPEAT
A-B RPT
CLEAR
+ + *
You can play back a specific title, chapter, track, or segment repeatedly. (Title
repeat, chapter/track repeat, A-B repeat)
DVD) CD
Repeating a Title, Chapter, or Track Repeating a Specific Segment
You can play back the same title, chapter, or track repeatedly. You can play back a specific segment repeatedly.
(Title, chapter/track repeat) (A-B repeat)
Press A-B RPT at the beginning of
the segment (point A) you want to
play repeatedly.
Select the title, chapter, or track
you want to repeat.
Press REPEAT.
Each time you press the REPEAT button,
the repeat mode changes as follows.
* DVD video disc
CHAPTER REPEAT Repeats the same
N chapter.
; , Press A-B RPT again at the end of
TITLE REPEAT Repeats the same title. .
the segment (point B).
{
REPEAT OFF Resumes normal
playback.
А-В
* Audio CD
TRACK REPEAT Repeats the same
track.
; , .
— Repeats the entire The DVD video player automatically
returns to point A and starts repeat
disc.
+ | playback of the selected segment (А-В).
Resumes normal
playback.
REPEAT OFF
|
To resume normal playback
To resume normal playback
CLEAR
Press CLEAR. Press CLEAR.
* You can specify a segment only within the current title.
* You cannot set the A-B repeat function for segment that include
multiple camera angles.
There may be a slight difference between point A and the location
where playback actually resumes depending on the discs.
mm 217
Advanced playback ) =>
Playing in a Favorite Order а
у | — — - А/ У / «< / >
—2
TITLE: 2
CHARTER : 25
1
. as CLEAR
You can combine your favorite titles, chapters, or tracks and play them
back in any order. You can program up to 30 items into the memory. 2
(Memory playback)
Setting Titles, Chapters, or Tracks in a Favorite Order
The DVD video player automatically plays back titles, chapters, or tracks in the order you program.
Insert a disc and press MEMORY
during stop.
| MEMORY SELECT : fe
The following menu appears.
H MEMORY — SELECT: be
PRESS [0]
r EEN
To select another chapter in the same title,
: you do not need to select the title number.
T: Title number C: Chapter number
Press PLAY while the MEMORY
menu appears on the TV screen.
Select the items you want in order
by pressing the number buttons,
then ENTER for each item.
Each time you press the «/ №» button,
the -- indication nextto Tand C is
highlighted in turn. Highlight where you
want to enter, then press the number
buttons.
The DVD video player starts memory
playback.
To change the programmed items
1 While the MEMORY menu appears on the TV screen,
press A/V to move the highlighted bar to the item
e.g. To play back chapter 25 in title 2, chapter you want to change.
12 in title 2, all the chapters in title 1, and
chapter 2 in title 4. Change the item following the instructions in step 2.
Title number Chapter number
ENTER
|
Memory 1 < + (2)- + (2)+(5)- O
To cancel the programmed items
1 While the MEMORY menu appears on the TV screen,
ENTER
Memory 2 (1)-(2)- (e) press A/V to move the highlighted bar to the item
ENTER you want to cancel.
Memory 3 (1) > ® 2 Press the CLEAR button.
ENTER
Memory 4 eG >(1)- >) ——(2)- (e)
To select tracks from an audio CD in order, press
the number buttons for the track, then press the
ENTER button for each item you want.
To resume normal playback from memory
playback
CLEAR Press CLEAR.
The MEMORY indicator disappears.
* |f you press the MEMORY button during memory playback, the programmed items will be displayed.
* You cannot select title, chapter, and track numbers not included on the disc.
* If you press the MEMORY or RETURN button while the MEMORY menu appears on the TV screen, the MEMORY menu disappears.
* The programmed items will be cleared when:
— you turn off the DVD video player, or
— you remove the disc.
22 uE
e
05
Advanced playback ) CT >=
Zooming a Picture
— — A/V /4/ DP
ZOOM
— CLEAR
You can magnify areas within a picture. (Zoom playback)
Zooming a Picture
You can zoom a picture. You can shift the zooming point as well.
To resume normal playback
Press ZOOM during normal
playback or slow motion.
The DVD video player magnifies in the
center of the picture.
Press ZOOM during zoom playback.
ZOOM
If you press A/V/</ > during zoom
playback, the zoom point shifts.
If the zoom point reaches the limit, the
color of “ZOOM” changes.
If you press CLEAR, the zoom point
returns to the center of the picture.
* During still playback, the ZOOM button cannot turn the zoom on or off.
* Zooming does not work on the sub-pictures such as subtitles or menu screens included on DVD video discs.
mu 23
Advanced playback ) ee
Selecting the Camera
Angle
ANGLE : 1 ANGLE : 2 ANGLE : 3—
ба — . *. e». o
ZN 7 ne CLEAR
You can select a preferred camera angle to watch a scene. ооо
DVD
Changing the Camera Angle
If the scene was recorded from multiple angles, you can easily change the camera angle of the scene you are watching.
To turn off the angle number indication
Press ANGLE while playing back a
scene recorded with multiple
angles.
Press the ANGLE button while the angle
icon in the DVD display is flashing. (£3)
E Current angle
number appears
CLEAR
Press CLEAR.
Press ANGLE or 4 while the angle
number appears on the TV screen.
Each time you press the ANGLE or 4
button, the camera angle changes.
V : Cycles backwards
You can change the camera angle directly
by pressing the number buttons
corresponding to its angle number instead
of using the 4/ Y buttons.
You can change the camera angle during still playback. The camera angle changes to the new setting when you resume normal playback.
While playing back a title that contains at least one scene recorded from multiple angles, the angle icon indicator illuminates in the DVD display.
24 mm
Advanced playback )
» Bonjour!
=>< ¡Buenos días!
Selecting a Language
CLEAR
DVD
Press AUDIO during playback.
Audio
channel
Recording
system
Language
Position number
setting
appears for
about 3
seconds
abbreviations. 37
The abbreviation of the language appears
instead of the language name. Refer to
the list of languages and their
|_ Current audio
DVD video disc change.
e.g.
Press AUDIO or A while the audio
setting appears on the TV screen.
Each time you press the AUDIO or A
button, the audio settings included on the
} 1 ENG PCM 2CH
|
ÄUDIO 2 FRE AC-3 6CH
J
|
|
VW : Cycles backwards
To turn off the audio setting indication
CLEAR
Press CLEAR.
About recording systems
6.
Discs and output sounds
This DVD video player uses the Dolby Digital (AC-3) and
PCM recording systems and cannot play back DVD video
discs recorded in any other recording system.
AC-3 5.1 Channel is displayed as “AC-3 ECH”
Note: Total channels available in AC-3 may vary from 1 —
DVD video discs Audio CDs
| Linear PCM .
Sound recording | poly iia Ler Pom
y 48kHz | 96kHz
pudio pans on AC-3 AC-3
coreo 9 AC-3 | PCM |or |AC-3|PCM| or
PCM PCM
ANALOG AUDIO * **
OUT jacks O O O O O
DIGITAL AUDIO Dolby PCM [PCM |PCM PCM
OUT jack igita (48 kHz) | (48 kHz) | (48 kHz)| — (44.1 kHz)
bitstream
*: 48 kHz processed
**: 96 kHz processed
When you turn on the DVD video player or replace a disc, player returns to the initial default setting.
When you select a sound which is not included on the disc, the DVD video player plays a prior sound programmed on the disc.
mu 25
Advanced playback )
language.
DVD
Displaying Subtitles
You can display subtitles from those included on the DVD
video disc.
Press SUBTITLE ON/OFF during
playback.
— Appears for
about 3 seconds
Good morning! Subtitles
To turn off the subtitles
SUBTITLE .
QUES TITLE Press SUBTITLE ON/OFF
o The subtitles disappear.
-—Appears for
about 3 seconds
* Some DVD video discs are set to display subtitles automatically, and
you cannot turn them off even if you set the subtitle function to off.
* During some scenes, the subtitles may not appear immediately after
you press the SUBTITLE ON/OFF button.
Selecting Subtitles
You can display subtitles on the TV screen and select a preferred subtitle
SUBTITLE
ON/OFF
A/V
— SUBTITLE
CD CD CD
CD CD CD @——— CLEAR
DOS
© © DO ©
DVD
Selecting a Subtitle Language
You can select the subtitle language from those included on
the DVD video disc.
Press SUBTITLE during playback.
|Current subtitle
setting appears
for about 3
seconds
E 1 ENG ON
Language
Position number
The abbreviation of the language appears
instead of the language name. Refer to
the list of languages and their
abbreviations. (37)
Press SUBTITLE or A while the
subtitle setting appears on the TV
screen.
Each time you press the SUBTITLE or A
button, the subtitle languages included on
the DVD video disc change.
e.g.
E 1 ENG ON
E 3 SPA ON
!
|
V¥ : Cycles backwards
To turn off the subtitle setting indication
CLEAR
Press CLEAR.
* When you turn on the DVD video player or replace a disc, player
returns to the initial default setting.
When you select a subtitle language which is not included on the
disc, the DVD video player plays a prior language programmed on
the disc.
* During some scenes, the subtitles may not appear immediately after
you change the subtitle language by pressing the 4 / Y buttons.
26 mm
Advanced Playback )
Display
TV screen.
Checking the Operational Status
You can view the current title number, track number, and total
playing time of the disc on the TV screen.
Using the On-Screen
You can view information about a disc and its operational status on the
Press DISPLAY during stop.
DVD video disc
Current title number
First chapter number in
е.9. the current title
STOP + Operational
TITLE: 2—
CHAPTER: 1— status
Audio CD
e.g. First track number of the disc
STOP 1 Operational
status
TRACK: 1
_ Total playing
time of the disc
When an audio CD is in the DVD video
player, the TOTAL indicator and total
playing time of the disc appear.
To turn off the on-screen display
DISPLAY
Press DISPLAY again.
-——— DISPLAY
Checking the Remaining Time and Setting Status
You can view the elapsed time, remaining time, and setting
status of the disc on the TV screen.
Press DISPLAY during playback.
DVD video disc
Current title number
Current chapter number
e.g. r— Operational status
PLAY | Remaining time
TITLE: 3- 45 ——Tinthe current title
0 Remaining time
- in the current
chapter
_ Elapsed time of
the current title
Playback mode
The REMAIN indicator and remaining time in
the current title appear in the DVD display.
Audio CD Current track number
е.9. —— Operational status
‘ay | Remaining
+ time in the
0 current track
0:01:20
Remaining time
— of the disc
_ Elapsed time of
the current track
Playback mode
The REMAIN indicator and remaining time in
the current track appear in the DVD display.
Press DISPLAY again during
playback.
When you play back an audio CD, the on-
screen display turns off.
e.g.
Current audio
TITLE: 3 — .
CHAPTER: setting
D 0:10:15
O 1 ENG AC-3 2CH
|_ Current subtitle
setting
_ Current angle
setting
The abbreviation of the language (e.g. ENG)
appears instead of the language name. Refer to
the list of languages and their abbreviations.
To turn off the on-screen display
DISPLAY
Press DISPLAY again.
Function Setup )
Customizing the Function
Settings
ET UP MENU
You can change the default settings to customize performance to your
preference.
Displaying the SET UP MENU Screen
The SET UP MENU screen asks you to select a setting category from AUDIO SETTING, FUNCTION and DISPLAY. The selected
category will provide you the setting details using the succeeding screen.
Press SET UP during stop.
The SET UP MENU screen appears.
Ш СЕТ UP MENU ___ SELECT: ofl
Press A/V to select the category, then press ENTER.
MN SET UP MENU — — SELECT: ele MN AUDIO SETTING _ SELECT: e
ENTER AUDIO OUT SEL. PCM
D RANGE CONTROL ON
VOCAL KARAOKE OFF
RETUAN
SETUP ENTER
RETURN;
Tr EI ЕМТЕН
JU 11
FUNCTION _______ SELECT: «je
Ш SET UP MENU ____ SELECT: be H
ENTER
TITLE STOP
OFF
REMOTE CONF | RM. ON
OSD ON
T CE ENE em»
| Г TL
DISPLAY — — — — SELECT: фе
Ш SET UP MENU SELECT: “le i
ENTER TV SHAPE
ANGLE ICON
SUBTITLE ——
DISC MENU ENG
RETURN
SETUP
For the setting details,
see раде п [ >.
The SET UP MENU screen disappears if you press the SET UP button while it is displayed.
28 mm
Function Setup )
Customizing the Function Settings (continued)
AUDIO SETTING
(1 AUDIO SETTING _ SELECT: фе
: 10
To select a preferred language from those included on the disc. (25)
1. To switch AC-3 (ANALOG OFF) and PCM (ANALOG ON). [11> (12> 13) [14) (25)
To turn on or off the function that makes faint sounds easier to hear even
if you lower the volume in late hours playback.
To turn on or off the vocal assist in DVD KARAOKE disc playback.
“ AUDIO OUT SEL.
D RANGE CONTROL
VOCAL KARAOKE
NED
Setting the Audio Sound
After you select AUDIO SETTING on the SET UP MENU screen (28), adjust to your preference.
Press 4/ Y to select the item, then press ENTER. | |
The setting screen of your selected item appears.
MN AUDIO SELECT: fe
| Select a preferred language by I AUDIO SETTING — №8 +
I TAL | AN pressing 4/ Y / « / № ‚ апа AIO UT SEL pom
FRENCH JAPANESE then press ENTER. D RANGE CONTROL ON
SPAN | SH DUTCH | VOCAL KARAOKE OFF
CHINESE KOREAN ENTER ná
_ GERMAN MALAY
ICE OFF
я
EN
SET UP
Some DVD video discs contain special output sound that describe the * Some DVD video discs may not include your pre-
actions on-screen for visually impaired persons. When you set selected language. In this case, the DVD video
DESCRIPTIVE SERVICE to “ON” by pressing the AUDIO button, the player automatically plays back the disc's initial
O DVD video player automatically plays back this special feature. language offering. |
fit AUDIO OUT SEL. SELECT : ee
Select the output sound type AC-3 MN AUDIO SETTING — SELECT:
or PCM by pressing < / № ‚ апа
then press ENTER.
D RANGE CONTROL ON
i A FF
ENTER am) VOCAL KARAOKE o
E ETE
ED ENTER)
* Select the output sound type according to your
system connection. 11) 12) 13 (25)
№ О RANGE CONTROL _ SELECT: off
Select ON or OFF by pressing il AUDIO SETTING _ SELECT: =f
« / № ‚ and then press ENTER.
AUDIO ENG
VOCAL KARAOKE OFF
ENTER — o KARAO
ED
ON: Dynamic range IS reduced, , * This function works on playback of Dolby Digital (AC-3) recorded discs.
OFF: Full dynamic range is maintained. * The level of Dynamic Range Reduction may differ depending on the
DVD video discs.
N 7
3
ENTER
AUDIO
RETURN
RETURN
to the previous menu screen displayed.
: If you press the RETURN button while a menu appears on the screen, you will return
DVD
CD
li VOCAL KARAOKE _ SELECT: efe
Select ON or OFF by pressing
< / >, and then press ENTER.
ENTER
=
RRETUAN
SETUP
ON: The vocal is output when it is recorded on the disc.
OFF: The vocal is not output.
N
HI AUDIO SETTING _ SELECT: e
AUDIO ENG
AUDIO OUT SEL. PCM
GE CONTROL
ENTER
7
The vocal assist feature is used during playback of AC-3 encoded DVD KARAOKE discs. This feature allows you
to turn off vocal audio tracks, or restore them for background accompaniment.
Press SET UP.
The setting screen disappears.
30 mm
Function Setup )
Customizing the Function Settings (continued)
FUNCTION
Ш FUNCTION — SELECT: fe
AC VEL NML. To select the black level of playback pictures.
TITLE STOP OFF
REMOTE CONF | RM. ON +7 . ‚ , .
OSD ON +7 To turn on or off the function that automatically stops playback after playing one title.
To turn on or off the confirmation beeper for each remote command.
To turn on or off the operational status display (On-screen display) on
the TV screen.
Setting the Functions
After you select FUNCTION on the SET UP MENU screen (28), adjust to your preference.
Press A/V to select the item, then press ENTER.
The setting screen of your selected item appears.
Ш FUNCTION — —— SELECT: e
Select a preferred black level by
pressing 4 / P , and then press CES AM
ENTER. REMOTE CONF I RM. ON
OSD ON
ENTER
=
ENTER
NORMAL: Standard black level.
ENHANCED: Expanded black level.
N J
Select ON or OFF by pressing Mm FUNCTION SELECT: +
</ >, and then press ENTER.
REMOTE CONFIRM. ON
ON
ENTER = OSD
ENTER
OFF: Player continues after playback of a title is completed.
ON: Player stops after playback of a title is completed.
N _/
HI REMOTE CONFIRM. SELECT: фе
Select ON or OFF by pressing ME FUNCTION — SELECT: $*
« / » , and then press ENTER. BLACK LEVEL NML .
TITLE STOP OFF
ENTER
=
RETURN,
ENTER
ON: Beeper sounds with each remote operation.
OFF: The beeper does not sound.
N —
4
3
ENTER
RETURN
RETURN
to the previous menu screen displayed.
: If you press the RETURN button while a menu appears on the screen, you will return
DVD) CD
Ш OSD _ —— ——— slecr:efe
Select ON or OFF by pressing
«4 / D , and then press ENTER.
ENTER
=»
SET UP
ON: Operational modes are displayed on-screen. (e.g. “PLAY”)
OFF: Operational modes are not displayed.
=
Hf FUNCTION SELECT : e
BLACK LEVEL NML.
TITLE STOP OFF
REMOTE CONF | RM. ON
GED
* CUTE ED
Press SET UP.
The setting screen disappears.
32 mm
Function Setup )
Customizing the Function Settings (continued)
DISPLAY
To select the display language.
TV SHAPE 16:9
1 — To select a picture size according to the aspect ratio of your TV.
ANGLE ICON ON +
SUBTITLE --- À
DISC MENU ENG +
Te To display the angle icon indicator on screen.
To select a preferred subtitle language from those included on the DVD video
disc.
To select a preferred disc menu language from those included on the DVD video
disc.
Setting the Displays
After you select DISPLAY on the SET UP MENU screen , adjust to your preference.
Press 4/Y to select the item, then press ENTER.
The setting screen of your selected item appears.
HN SCREEN DISPLAYS SELECT: “e
Select a preferred language by m DISPLAY SELECT: FF
ENG „| pressing A/V and then press
FRENCH | ENTER.
ANGLE ICON
SPAN | SH
; SUBTITLE LÙ-
| ENTER am) DISC MENU ENG
Cam )
SETUP ENED
T EN [ENTERA
Select your TV type by Mm DISPLAY SELECT: Fe
pressing < / P , and then
press ENTER.
SUBTITLE _
ENTER DISC MENU ENG
16:9 (WIDE): — Select when a 16:9 wide TV is connected. * The displayable picture size is preset on the DVD video
4:3 (NORMAL): Select when a 4:3 normal TV is connected. disc. Therefore, the playback picture of some DVD video
discs may not conform to the picture size you select.
* When you play DVD video discs recorded in the 4:3
picture size only, the playback picture always appears in
the 4:3 picture size regardless of the TV shape setting.
If you select 4:3 (NORMAL): PS (PAN-SCAN):
Displays pictures cropped to fill your TV
J screen. Either or both sides of the picture are
Select PS or LB by pressing cut off.
</ bp, and then press LB (LETTER BOX):
ENTER. Displays theatrical images with masking bars
ENTER above and below the picture.
PS (PAN-SCAN) LB (LETTERBOX)
TITLE
MENU
3
ENTER
RETURN
SUBTITLE
ANGLE
RETURN
: If you press the RETURN button while a menu appears on the screen, you will return
to the previous menu screen displayed.
DVD
CD
N
ICON — — SELECT: offs
ll ANGLE
SNE
Select ON or OFF by pressing
< / D , and then press ENTER.
ENTER
=»
M DISPLAY ___ SELECT: fm
SCREEN DISPLAYS ENG
TV SHAPE 16:9
"SUBTITLE
DISC MENU
ENG
“CD
+ ED
ON: The angle icon automatically appears in white on the TV screen while a scene recorded from multiple angles is
played back. When you display the angle number on the screen by pressing the ANGLE button, the angle icon is
lit in red.
OFF: The angle icon is not displayed.
—
N
ENGLISH ITALIAN
FRENCH JAPANESE
SPANISH DUTCH
CHINESE KOREAN
AY
EXTENDED FEATURES OFF
Some DVD video discs contain special subtitles, an enhancement of closed
captioning for hearing impaired persons. When you set EXTENDED FEATURES
to “ON” by pressing the SUBTITLE button, the DVD video player automatically
displays these special subtitles.
ur DISC MENU — — SELECT: "e
ENGL oh ITALIAN
FRENC JAPANESE
SPANISH DUTCH
CHINESE KOREAN
GER
М МАГА
ENTER
| GED
SETUP
Select a preferred language by
pressing A/ Y /</ PD, and
then press ENTER.
ENTER
=»
Select a preferred language by
pressing 4/ Y /</ P,and
then press ENTER.
ENTER
=
To change the language while a disc is inserted.
1) Press the TITLE or MENU button to display the disc menu.
2) Press the SET UP button.
if the disc menu has only one language, the display does not
№ DISPLAY — — SELECT: Фе
ENG
16:9
SCREEN DISPLAYS
TV SHAPE
ON
ENG
ENTER
* Some DVD video discs may not include your pre-
selected language. In this case, the DVD video
player automatically displays subtitles consistent
with the disc's initial language setting.
HI DISPLAY — — SELECT: fe
SCREEN DISPLAYS ENG
TV SHAPE 16:9
ANGLE ICON ON
SUBTITLE -—
RETUR
1SET UP
ENTER
3) Press the SET UP button repeatediy to select the language.
Refer to “Table of languages”.
4) Press the ENTER button.
appear.
Press SET UP.
The setting screen disappears.
| DISC MENU: ENG
The disc menu is displayed in the selected language.
—
34mm
Function Setup )
Setting the Parental Lock
1,7
4,56
3, 4, 5,6
rR—e
Lem
STOP
RETURN
CLEAR
2,3
You can use the parental lock function only with DVD video discs
equipped with the parental lock feature.
Setting the Parental Lock
DVD video discs equipped with the parental lock function are rated according to their content. The contents allowed by a parental
lock level and the way a DVD video disc can be controlled may vary from disc to disc. For example, if the disc allowed you could edit
out violent scenes unsuitable for children and replace them with more suitable scenes, or lock out playback of the disc altogether.
Press SET UP during stop. Press </P to select the country
The SET UP MENU appears on the TV whose standards were used to rate
screen. the DVD video disc, then press
ENTER.
The following menu appears.
Press 9 twice.
The following menu appears.
Hl PARENTAL LOCK
Press A/ Y to select the parental
lock level, then press ENTER.
You cannot play back DVD video discs rated
Press the number buttons to create
a personal 4-digit security code,
then press ENTER.
e.g.
+
it PARENTAL LOCK _ SELECT: =$
If you make a mistake before pressing the
ENTER button, press the CLEAR button and
enter your 4-digit security code again.
Press </P to select “ON,” then
press ENTER.
The following menu appears.
MH PARENTAL LOCK _ SELECT: «lle
higher than the level you selected unless you
cancel the parental lock function.
For example, when you select level 7, the
discs rated higher than level 7 are locked out
and cannot be played back.
e.g. When you select USA
H PARENTAL LOCK
E When you
Ma ad dos Seti select “CAN,”
“САМУ”
appears
instead.
The parental lock level is equivalent to the
following USA movie ratings.
LEVEL 7: NC-17 LEVELS3: PG
LEVEL6: R LEVEL 1: G
LEVEL 4: PG 13
The parental lock levels for “CAN” (Canada)
are included for future use. Check the
appropriate parental lock level when you buy
a DVD video disc equipped with the parental
lock feature in the future.
Press SET UP.
The SET UP MENU disappears.
RETURN
: If you press the RETURN button while a menu appears on the screen, you will return
to the previous menu screen displayed.
To change the parental lock level To cancel the parental lock function
You can change the parental lock level by following the 1 Follow steps 1 and 2 in “Setting the Parental Lock.”
steps in “Setting the Parental Lock.”
In step 3, press the number buttons to enter your 4-digit
security code, then continue to step 4.
2 Press the number buttons to enter your 4-digit
security code, then press the ENTER button.
If you make a mistake, press the CLEAR button and
enter the correct 4-digit security code.
3 Press </P to select “OFF” then press the ENTER
button.
If you make a mistake, press the CLEAR button and enter
the correct 4-digit security code.
SELECT : jj
IH PARENTAL LOCK
To change your 4-digit security code
You can change your 4-digit security code.
Follow steps 1 and 2 in “Setting the Parental Lock.”
2 Press the STOP button four times while the security
code menu appears on the TV screen.
STOP STOP STOP STOP
OMOMOMO
The 4-digit security code is cleared.
3 Press the number buttons to create a new 4-digit
security code, then press the ENTER button.
4 Complete steps 4 to 7 in “Setting the Parental Lock.”
The SET UP MENU appears again.
Press the SET UP button.
The SET UP MENU disappears, and the parental lock
function is cancelled.
DVD video discs may or may not respond to the parental lock
settings. Make sure this function works with your DVD video discs.
36 mm
Function Setup )
Table of Languages
Table of Languages and Their Abbreviations
Abbreviation | Language Abbreviation | Language Abbreviation | Language Abbreviation | Language
of the of the of the of the
Language Language Language Language
——— No alternate EO Esperanto LN Lingala SL Slovenian
language ET Estonian LO Laotian SM Samoan
CHI Chinese EU Basque LT Lithuanian SN Shona
DUT Dutch FA Persian LV Latvian, Lettish SO Somali
ENG English FI Finnish MG Malagasy SQ Albanian
FRE French FJ Fiji MI Maori SR Serbian
GER German FO Faroese MK Macedonian SS Siswati
ITA Italian FY Frisian ML Malayalam ST Sesotho
JPN Japanese GA Irish MN Mongolian su Sundanese
KOR Korean GD Scottish Gaelic MO Moldavian SV Swedish
MAY Malay GL Galician MR Marathi SW Swahili
SPA Spanish GN Guarani MT Maltese TA Tamil
AA Afar GU Gujarati MY Burmese TE Telugu
AB Abkhazian HA Hausa NA Nauru TG Tajik
AF Afrikaans H! Hindi NE Nepali TH Thai
AM Amharic HR Croatian NO Norwegian TI Tigrinya
AR Arabic HU Hungarian OC Occitan TK Turkmen
AS Assamese HY Armenian OM (Afan) Oromo TL Tagalog
AY Aymara IA Interlingua OR Oriya TN Setswana
AZ Azerbaijani IE Interlingue PA Panjabi TO Tongan
BA Bashkir IK Inupiak PL Polish TR Turkish
BE Belorussian IN Indonesian PS Pashto, Pushto TS Tsonga
BG Bulgarian IS Icelandic PT Portuguese TT Tatar
BH Bihari IW Hebrew QU Quechua TW Twi
Bl Bislama JI Yiddish RM Rhaeto-Romance UK Ukrainian
BN Bengali, Bangla JW Javanese RN Kirundi UR Urdu
BO Tibetan KA Georgian RO Rumanian UZ Uzbek
BR Breton KK Kazakh RU Russian VI Vietnamese
CA Catalan KL Greenlandic RW Kinyarwanda VO Volapük
CO Corsican KM Cambodian SA Sanskrit WO Wolof
CS Czech KN Kannada SD Sindhi XH Xhosa
CY Welsh KS Kashmiri SG Sango YO Yoruba
DA Danish KU Kurdish SH Serbo-Croatian ZU Zulu
DZ Bhutani KY Kirghiz Si Singhalese |
EL Greek LA Latin SK Slovak
mu 37
Others )
Notes on Discs
On Handling Discs
* Do not touch the playback side of the disc.
Playback side
* Do not attach paper or tape to discs.
x E)
On Cleaning Discs
* Fingerprints and dust on the disc cause picture and sound
deterioration. Wipe the disc from the center outwards with a
soft cloth. Always keep the disc clean.
* |f you cannot wipe off the dust with a soft cloth, wipe the disc
lightly with a slightly moistened soft cloth and finish with a
dry cloth.
* Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for vinyl
LPs. It may damage the disc.
On Storing Discs
* Do not store discs in a place subject to direct sunlight or
near heat sources.
* Do not store discs in places subject to moisture and dust
such as a bathroom or near a humidifier.
e Store discs vertically in a case. Stacking or placing objects
on discs outside of their case may cause warping.
About This Owner’s Manual
This owner's manual explains the basic instructions of this
DVD video player. Some DVD video discs are produced in a
manner that allows specific or limited operation during
playback. As such, the DVD video player may not respond to
all operating commands. Refer to instruction notes of discs.
“ W ” may appear on the TV screen during operation.
White “ 4 ” means that the operation is not permitted by the
DVD video player; red “ W ” by the operation is not permitted
by DVD video disc.
This section shows you how to handle, clean, and store discs.
Playable Discs
This DVD video player can play back the following discs.
Disc mark ¡Contents | Disc Maximum
size playback time
Approx. 4 hours
(single sided disc)
Audio | 12cm Approx. 8 hours
DVD + (double sided disc)
video DVD Video
discs > | (moving Approx. 80 minutes
pictures) |g (single sided disc)
Approx. 160 minutes
(double sided disc)
12 cm 74 minutes
| COMPACT
apa E Audio | 8CM 20 minutes
5 DIGITAL AUDIO (CD
single)
You cannot play back discs other than those listed above.
This DVD video player uses the NTSC color system, and
cannot play back DVD video discs recorded in any other color
system (PAL, SECAM, etc.).
Notes on Region Numbers
The region number of this DVD video player is 1. If region
numbers, which stand for their playable area, are e on
your DVD video disc and you do not find té ©
playback will not be allowed by the player. (In this case, the
DVD video player displays the message.)
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on
cable, play in public, and rent copyrighted material without
permission.
DVD video discs are copy protected, and any recordings
made from these discs will be distorted. |
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.
38 mm
Others ) |
Check the following guide for the possible cause of a problem before contacting service.
Symptoms and Correction
Before Calling Service Personnel
exhausted.
Symptom Cause Correction Page
No power. The power plug is disconnected. Connect the power plug into the wall outlet | 11,12
securely.
No picture. * The TV is not set to receive DVD signal | * Select the appropriate video input mode 15
output. on the TV so the picture from the DVD
video player appears on the TV screen.
* The video cable is not connected * Connect the video cable into the jacks 11,12,
securely. securely. 13, 14
No sound. * The equipment connected with the audio | * Select the correct input mode of the 15
cable is not set to receive DVD signal audio receiver so you can listen to the
output. sound from the DVD video player.
* The audio cables are not connected * Connect the audio cable into the jacks 11,12,
securely. securely. 13, 14
* The power of the equipment connected * Turn on the equipment connected with —
with the audio cable is turned off. the audio cable.
* The setting of output sound type is not * Set the audio setting correctly. 28, 29
correct.
The playback picture has * The disc is dirty. * Eject the disc and clean it. 38
occasional distortion. e tis in fast forward or fast reverse * Sometimes a small amount of picture distortion | — —
playback. may appear. This is not malfunction.
Brightness is unstable or * The copy protection's effect. * Connect the DVD video player to the TV 11
noises are produced on directly.
playback pictures.
The DVD video player does | * No disc is inserted. * Insert a disc. (Check that the DVD or 8
not start playback. audio CD indicator in the DVD display is
lit.)
* An unplayable disc is inserted. * Insert a playable disc. (Check the disc 38
type and color system.)
* The disc is placed upside down. * Place the disc with the playback side 15
down.
* The disc is not placed within the guide. * Place the disc on the disc tray correctly 15
inside the guide.
* The disc is dirty. * Clean the disc. 38
* A menu is on the TV screen. * Press the SET UP button to turn off the —
menu screen.
* The parental lock function is set. * Cancel the parental lock function or 35, 36
change the parental lock level.
Buttons do not work. Power supply fluctuations or other Turn the power on or of with the POWER —
abnormalities such as static electricity may | button. Or disconnect the power plug and
interrupt correct operations. insert it into the wall outlet again.
The remote control does not | * The remote control is not pointed at the | * Point the remote control at the remote 10
work properly. remote sensor of the DVD video player. sensor of the DVD video player.
* The remote control is too far from the * Operate the remote control within about 7 10
DVD video player. m.
* The batteries in the remote control are * Replace the batteries with new ones. 10
ия 39
Others )
Specifications
DVD Video Player / Outputs / Supplied Accessories
[DVD Video Player]
120 V AC, 60 Hz
20 W
3.3 kg
430 x 81 x 300 mm (W/H/D)
Standard NTSC
Semiconductor laser, wavelength 650 nm
DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz
96 kHz sampling 4 Hz to 44 kHz
Audio CD : 4 Hz to 20 kHz
More than 108 dB
More than 96 dB
Less than 0.004 %
Below measurable level (less than +0.001 % (W.PEAK))
Temperature: 5 °C to 35 °C, Operation status: Horizontal
[Outputs]
1.0V (p-p), 75 Q, negative sync., pin jack x 1
(Y) 1.0 V (p-p), 75 Q, negative sync., Mini DIN 4-pin x 1
(C) 0.286 V (p-p), 75 Q
0.5 V (p-p), 75 ©, рп jack x 1
2.0 V (rms), 330 Q, R) x 1
[Supplied Accessories]
S video Cable een ee seance 1
Audio/video cable .......................11meemeiiirree ene ee 1
Remote control (SE-R2107) ...................... 2... en, 1
Batteries (AAA) .........................eezesoereeririrccuecer carr rr recen een. 2
* Designs and specifications are subject to change without notice.
40 mm
LIMITED WARRANTY DVD VIDEO PLAYER
Toshiba America Consumer Products, Inc. ((TACP”), Toshiba Hawaii (“THI”) and Toshiba Canada Limited (“TCL’”) make the following limited warranties. These limited
warranties extend to original purchaser or any person receiving this set as a gift from the original purchaser and to no other purchaser or transferee.
Limited Ninety (90) Day Warranty
TACP/THI warrant this product against defects in materials or workmanship for a
period of ninety (90) days after the date of original retail purchase. During this
period, TACP/THI will repair a defective product or part without charge to you.
You must deliver the entire product to a TACP/THI Authorized Service Station.
You are responsible for all transportation and insurance charges for the unit to
and from the Authorized Service Station. If you live in the U.S.A. you may, at
your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit with a new or
refurbished unit. Canadian consumers are requested to contact TCL. In
Hawaii consumers are requested to contact THI.
Limited One (1) Year Warranty
TACP/THI further warrant the parts in this product against defects in materials
or workmanship for a period of one (1) year after the date of original retail
purchase. During this period, TACP/THI will replace a defective part without
charge to you, except that if a defective part is replaced after ninety (90) days
from the date of the original retail purchase you pay labor charges involved in
the replacement. You must also deliver the entire product to a TACP/THI
Authorized Service Station. You are responsible for all transportation and
insurance charges for the unit to and from the Authorized Service Station. If you
live in the U.S.A. you may, at your option, return your DVD Unit to:
Toshiba America Consumer Products Inc.
Returns Center
1420C Toshiba Dr.
Lebanon, TN 37087
Upon receipt we will, at our option, exchange the DVD Unit with a new or
refurbished unit. Canadian Consumers are requested to contact TCL. In
Hawaii consumers are requested to contact THI.
Rental Units
The warranty for rental units begin with the first rental or thirty (30) days from
the date of shipment to the rental firm, whichever comes first.
How to Obtain Warranty Service
Commercial Units
Products sold and used for commercial use have a limited ninety (90) day
warranty for all parts and labor.
"Owner’s Manual
You should read the owner's manual thoroughly before operating this product.
You should complete and mail the enclosed Demographic card within ten (10)
days after you, or the person who has given you this product as a gift,
purchased this product. This is one way to enable TACP to provide you with
better customer service and improved products. Failure to return the card will
not affect your rights under this warranty.
Your Responsibility
The above warranties are subject to the following conditions:
(1) You must retain your bill of sale or provide other proof of purchase.
(2) You must notify a TACP/THI/TCL /Authorized Service Station within thirty
(30) days after you discover a defective product or part.
(3) All warranty servicing of this product must be made by a TACP/THI/TCL
Authorized Service Station.
(4) U.S.A. warranties are effective only if the product is purchased and
operated in the U.S.A. or Puerto Rico.
(5) Labor service charges for set installation. Set up, adjustment of customer
controls and installation or repair of antenna systems are not covered by
this warranty. Reception problems caused by inadequate antenna systems
are your responsibility.
(6) Warranties extend only to defects in materials or workmanship as limited
above and do not extend to any product or parts which have been lost or
discarded by you or to damage to products or parts caused by misuse,
accident, damage caused by Acts of God, such as lighting or fluctuations in
electric power, improper installation, improper maintenance or use in
violation of instructions furnished by us; or to units which have been altered
or modified without authorization of TACP/THI/TCL or to damage to
products or part thereof which have had the serial number removed,
altered, defaced or rendered illegible.
(7) Should you elect to return your DVD Unit to TACP after the ninety (90) days
and within one (1) year, or after the warranty period has expired: Cali (800)-
631-3811 to receive information concerning an exchange price. Payment
must be enclosed with product in the form of a certified check or money
order including reason for return.
(8) Physically damaged DVD Units are not acceptable for repair or exchange
whether in or out of warranty and will be returned as received.
part.
proof of purchase must be enclosed.
In Hawaii contact:
Toshiba Hawaii Inc.
327 Kamakee Street
Honolulu, HA 96814
(808)-521-5377
In the Continental United States contact:
Toll Free
800-631-3811
(1) Refer to the troubleshooting guide in your owner's manual. This check list may solve your problem.
(2) In the U.S.A., only call the TACP toll free number 800-631-3811, or if in Hawaii or Canada see listing below within (30) days after you find a defective product or
(3) Arrange for the delivery of the product to the TACP/THI/TCL Authorized Service Station or TACP Return Center. Products shipped to the Service Station must be
insured and safely and securely packed, preferably in the original shipping carton, and a letter explaining the defect and also a copy of the bill of sale or other
In Canada contact:
Consumer Electronics Group
191 McNabb Street
Markham, Ontario L3R 8H2
(905)-470-5400
Consumer Electronics Group
22171 Fraserwood Way
Richmond, B.C. V6W 1J5
(604)-303-2500
Consumer Electronics Group
1643 North Service Road
Droval, QC H9P 1J1
(514)-856-4100
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the duration of the
limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other
warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall TACP/THI be
liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever. The time within
which an action must be commenced to enforce any obligation of TACP/THI arising under the warranty or under any statute, or law of the Unite States or any state
thereof, is hereby limited to ninety (90) days from the date you discover or should have discovered, the defect. This limitation does not apply to implied warranties arising
under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some states do not allow limitation on how long an
implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to
you.
ATTENTION CANADIAN CONSUMERS:
U.S.A. and used in Canada are not covered by these warranties. '
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and forward this completed form with a copy of bill of
sale to TOSHIBA OF CANADA to “Register and Validate” their warranty. Product must be purchased from an Authorized Canadian Dealer. Products purchased in the .
IMPORTANT: PACKING AND SHIPPING INSTRUCTION
When you send the product to a Service Station, you must use the original carton box and packing material, then insert the original carton box containing the unit into
another carton using more packing material.
mm 47
TOSHIBA
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement