Panasonic NI-N70NR Small Appliance Owner's Manual

1. Fill the iron as described in "HOW TO FILL"
2. Set the iron vertically and make sure the temperature
selector dial is set to OFF.
Plug the AC cord into the electrical outlet
3. Set the temperature selector dial to the " &"
indication area.
4. Preheat the iron until the indicator light goes out,
usually about 1-2 minutes.
5. Simply pump the jet of steam button when it is desired.
But pump the jet of steam button several times before
using for the first time at each ironing session.
6. Allow at least 5 seconds between uses of jet of steam
to prevent water spotting. Use a press cloth if necessary.
VERTICAL STEAM (NI-N50NR / N52SR / N7ONR/N74NR Only)
To get better results when using vertical Jet of steam,hang
the garment on a clothes hanger. Curtain and drapes may
also be steamed once they're hung. Hold the iron away
from your body close to but not touching the fabric. Pull
the fabric tight with your free hand and pump the Vertical
steam button (Jet of Steam Button) at 5-second intervals
as you pass the iron over the wrinkled fablic.
WARNING:
Never iron clothes on the body or point your iron at anyone
when steaming.
Keep hands and body away from steam areas while using
vertical steam feature.
SELF-CLEANING
With the self-cleaning feature you can flush out mineral residues from the steam generating
chamber and the steam vents .-refreshing your iron each time for a longer steaming life.
It is very important to operate the self-cleaning feature after each steam ironing to prevent
mineral accumulations from hardening.
1. Check water level. Water level should be at the 1/2 full. When water level
is below 1/2 full, fill with water according to the instruction in "How to Fill".
2. Preheat at "6" setting. (in about 1-2 minutes)
Makes sure that the steam button is in the Dry position.
3. Set the dial to off and remove the Ac plug.
. Hold the iron horizontally over the sink.
5. Pump the "Jet of Steam" button quickly (at least 3
times per second) about 20-30 times.
+
COMPONENTS IDENTIFICATION
NI-N50NR/NI-N21SR/NI-N52SR/NI-N70NR/NI-N74NR
(This picture is NI-N50NR)
Jet of steam button /
Vertical Steam button
Spray Button
Steam Button
са fm fm
Dry Low High
gleam steam
Water Fill Cover
Spray Nozzle >
Soleplate
Water Level Indication
Water Reservoir
(Water window)
Handle
À Wind Button
Cord Reel Unit
AC Power Cord
Temperature
Select Indicator
Plug
— Thermostat Operating Indicator Light
Temperature Selector Dial
6. While self-cleaning, pitch the iron up and down slowly to help clean the entire inside
and let the water drip out of the soleplate vents.
7. Check that all water and steam thoroughly stop coming out of the soleplate vents
After self-cleaning is finished dump any remaining water out of the iron.
8. Iron on a towel to remove any drops of water remaining on the bottom of iron.
9. Cool as usual and store the iron on its heel rest. Never store an iron on its soleplate
or with water in it.
NOTE:
If water still remains inside the soleplate after self-cleaning operation, then dry out the iron
by vaporizing the remaining water setting the iron on the "6" setting. And follow the
instructions under "AFTER EACH USE".
Stay Clean Vents (NI-N70NR/N74NR Only)
The built-in Anti Calcium Cassette in the Capsule Tank continuously reduces scale built-up
in the vaporizing chamber of the iron.
This system makes it possible to use steam function for a long period of time preventing
steam vents clogging.
HOW TO CARE FOR YOUR IRON
AFTER EACH USE
1. Turn iron off and unplug.
2. Empty iron immediately after using, Don't store the iron with water in it.
3. Depress the steam button down into the dry position.
4. Wait until the iron has cooled before storing it, and always set it on the heel rest to protect
the soleplate from scratching, corroding or staining.
5. After letting iron cool completely, push the cord wind button to wind the cord, Store iron
vertically in a safe place after winding cord completely.
MAIN BODY
After unplugging and cooling the iron, simply wipe off with a damp cloth and if necessary,
use a mild detergent.
NEVER USE ANY HARSH CLEANERS.
SOLEPLATE
Starch and other residue may be easily removed from the soleplate with a damp cloth.
To avoid scratching the finish never use a metallic pad to clean the soleplate, and never
place the iron on a rough surface.
If synthetics are ironed at too high a temperature, not only is the fabric usually ruined, but
the iron soleplate is often covered with the melted remains of the synthetic fabric.
The best way to remove synthetic residue from the soleplate is to heat the iron and to iron
over an old cotton rag.
CAUTION:
Never use steam iron cleaners in the iron, since they may damage the inside of the iron.
-9-
CAUTION DURING USE OF RETRACTIVE POWER CORD
(1) When retracting power cord, always grasp the plug with one hand while pressing the cord
wind button with the other hand.
(2) If cord does not retract completely, pull it out slightly and wind it again while guiding it into
the reel.
(3) Unwind the power cord in the amount of length you need before plugging it to the wall
outlet.
(4) If the power cord seems hard to unwind due to an improper winding, pull firmly until it is
released.
(5) Do not allow small children to handle the retractive power cord as this may cause the
cord to "whip" and cause injury.
(6) If grasp the rear of handle during ironing, the power cord may be retracted by pressing the
cord wind button.
GENERAL HINTS BEFORE USING YOUR Panasonic IRON
1. Read this instruction book to become familiar with the iron and its features.
2. Most ordinary tap water can be used in this iron. In extremely hard water areas, distiled or
demineralized water should be used. Do not use water processed through home water
softening systems, because this water contains minerals that may be harmful to the iron.
3. It is best to start ironing garments requiring lower temperature setting first. This will help
to avoid damaging garments. If you are not sure of the fabric content, first test the
temperature of the iron on an area of a garment where it will not show.
HELPFUL IRONING TIPS
The Temperature Selector Dial of the Panasonic iron has dots on it, in addition to numbers
and color indications. This makes it easy to adjust the iron for steam, more or less steam, and
any other temperature setting desired. The dots are international fabric protection symbols
for various temperature ranges:
e Low Temperature
ee Medium Temperature
eee High Temperature
Many garments are labeled with these dots as a guide for selecting the proper ironing
temperature. For general information about ironing temperatures, refer to the handy fabric guide
on the iron.For more specific information, use the "Fabric Ironing Chart" found on page 10.
As a guide to the international Textile Care Labeling code,the following symbols are noted for
your information.
INTERNATIONAL TEXTILE CARE
& LABELING CODES W CA
Washing Bleaching Ironing Dry Cleaning
A symbol crossed out indicates that the article of clothing
must not be subjected to the particular treatment.
EXAMPLE: (DO NOT BLEACH) xXx
- 4 -
FABRIC IRONING CHART
NOTES: 1. Check garment for specific ironing instructions, Always follow manufacturer's
instructions.
2. Iron blended fabrics at setting for lower-temperature fiber or for the
highest-percentage fiber.
3. Use caution, some synthetics may melt at high temperature.
Temperature :
Fabric i i
Selector Setting Ironing Recommendations
ACRYLIC
* ACRILAN Dry iron on wrong side, or use a press cloth on
* CRESLAN top of fabric. Dont sprinkle water directly on
1 * ORLON fabric to avoid spots.
ACETATE To iron suede, cover ironing board with brown
METALLICS paper and use it as a press cloth.
SUEDE
NYLON
2 * АМТОВОМ Dry iron on wrong side.
* CAPROLAN
SILK
PERM. PRESS
RAYONS
POLYESTER
* DACRON Dry iron on wrong side. To touch-up collars,
3 * FORTREL cuffs, pockets, etc., iron lightly on right side
* KODEL PRE DA
TRIACETATE
* ARNEL
W'n W COTTON
WOOL Steam ironing is suggested. Never iron completely dry.
: ; holdi |
4 VELVET To ron velvet, steam iron holding the slightly above the
fabric
Steam ironing is suggested. Sprinkle water on the fabric,
5 COTTON depending on its thickness. Iron dark fabric on wrong
side to avoid unwanted sheen.
Steam ironing is suggested. Iron dark fabrics on wrong
LINEN . :
side to avoid unwanted sheen.
* Trademarks of Fiber Manufacturers.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way Secaucus
New Jersey 07094
Panasonic Sales Company
Division of Matsushita Electric of
Puerto Rico, Inc.("PSC")
Ave.65 de Infanteria. Km. 9.5
San Gabriel Industrial Pack, Carolina,
Puerto Rico 00985
consumerproducts @ panasonic.com i82006-0K32D
-10 -
Before ironing, sort the garments according to the different heat settings required. Iron
fabrics that need a lower temperature first.
Do not touch plastic buttons with a hot iron because they may melt.
Be careful around zippers and similar items to prevent the soleplate from scratching.
HOW TO FILL
1. Be sure the iron is unplugged from the electrical outlet before filling
with water. Push the steam button down, hold the iron, open
Water Fill Cover and slowly fill the iron with water (see NOTE)
up to "MAX" indication.(about 5.6
ounces/160ml).
2. Do not overfill. Check the correct
water level with the iron in the vertical position.
3. Close the Water Fill Cover.
NOTE:
Most ordinary tap water can be used in this iron. In extremely hard water areas, distilled or
demineralized water should be used. If distilled water is used, the iron must be seasoned by
using tap water for the first four times.
After that, tap water should be used once a month. This is necessary to coat the steam
chamber for proper performance.
HOW TO USE AS A STEAM IRON
1. Fill the iron as described in "HOW TO FILL",
2. Set the iron vertically and make sure the Temperature Selector Dial is set to OFF.
Plug the AC cord into the electrical outlet.
3. Set the temperature selector dial to the" <A> "or " 2 "(steam) zone.
"> " zone: Low steam, for thin or delicate fabrics requiring a small amount of steam.
- <=? " zone: High steam, for fabrics requiring a lot of steam. (i. e. thick materials, items with
stubborn wrinkles.)
4. Preheat the iron until the indicator light goes out, usually about 1-2 minutes.
This light will go on and off during ironing to indicate the temperature chosen by the selector
dial is being maintained.
5. Hold the iron horizontally and press the steam button into the steam position.
Steam button is regulated as follows.
Panasonic
Electric Steam Iron
Operating Instructions
Model No.NI-N50NR/N21SR/N52SR/N70NR/N74NR
NI-N50NR
Please read these instructions carefully before using this product and
save this manual for future use.
For assistance, please call : 1-800-211-PANA(7262)
or send e-mail to:cosumerproducts € panasonic.com
or visit us at WWW.panasonic,com (U.S.A)
For assistance, please call : 787-757-4300
or visit us at WWW.panasonic,com
(Puerto Rico)
NOTE: 3 position steam button.
a"
Dry Low steam High steam
(Button UP : for High steam, MED: for Low steam )
Temperature Zone | Steam Button Position
Fm
fo fm)
Now steam ironing can begin
GC
6. Anytime the iron is set vertically the steaming action will stop.
NOTE: Do not use the steam button unless the iron is sufficiently hot enough to produce
steam, otherwise water will leak out through the vents instead.
HOW TO USE AS ADRY IRON
1. Press the steam button down to the dry position.
2. Place the iron vertically, set the selector dial to OFF.
3. Plug in the iron.
4. Set the temperature selector dial to the desired position.
(Refer to the Fabric Ironing Chart in this manual on page 10)
5. Preheat the iron until the indicator light goes out, usually about 1-2 minutes.
HOW TO USE THE SPRAY FEATURE
Before using the spray feature, check the garment label for
ironing instructions because some fabrics may spot or
stain with moisture.
The spray feature is particularly helpful for removing
stubborn wrinkles and where extra dampening is needed.
The spray may be used with steam or dry ironing.
1. Simply pump the spray button when spray De
is desired. If the spray doesn't work =
immediately just keep pumping till it does.
2. Togetafiner spray, pump the button vigorously. To get coarser spray, pump the button
more slowly. For best results, use a quick, full stroke.
-6-
IMPORTANT SAFEGUARDS
When using your flatiron,basic safety precautions should always be followed,
including the following:
1.
Read all instructions.
2. Use iron only for its intended use.
3. To protect against a risk of electric shock, do not immerse the iron in water
or other liquids.
4. The iron should always be turned to OFF before plugging or unplugging
from outlet. Never yank cord to disconnect from outlet; instead, grasp plug
and pull to disconnect.
. Do not allow cord to touch hot surfaces. Let iron cool completely before
putting away.
Wind cord into cord reel unit when storing.
. Always disconnect iron from electrical outlet when filling with water or
emptying and when not in use.
. Do not operate iron with a damaged cord or if the iron has been dropped
or damaged. To avoid a risk of electric shock, do not disassemble the iron,
take it to a qualified serviceman for examination and repair.
Incorrect reassembly can cause a risk of electric shock when the iron is
used.
8. Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an ironing
board.
9. Burns can occur from touching hot metal parts, hot water,or steam. Use
caution when you turn a steam iron upside down-there may be hot water
in the reservoir.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate another high wattage appliance
on the same circuit.
2. If an extension cord is absolutely necessary, a 10 ampere cord should
be used. Cords rated for less amperage may overheat. Care should be
taken to arrange the cord so that it cannot be pulled or tripped over.
SAVE THESE INSTRUCTIONS
©2004 Matsushita Electric industrial Co., LTD. All rights reserved.
- 2-
Electronic 3-Way AUTO SHUT-OFF FUNCTION
1. When the iron is left unmoved with its soleplate facing down or on its side for approx.
1.minute, the iron will automatically shut off power to the heater by itself.
2. When the iron is left unmoved on its heel rest for approx.
10 minutes, the iron will automatically shut off power to the heater by itself.
3. To turn the iron back on to resume ironing, simply move the iron in any way.
Reheat the iron until the indicator light goes out, if you have left the iron in its auto shut
off mode for 10 minutes or more.
Ca
1 minute to "OFF"
1 Ominutes to "OFF"
NOTE: 1. The Auto shut off system works regardiess of position of the temperature selector
dial, even at "OFF" position.
2. When you finish ironing, always unplug the iron.
X Licensed under U.S.patent No. 4,686,352 and foreign counterparts.
HOW TO USE JET OF STEAM FEATURE
The jet of steam feature gives extra steam which goes deep into the garment and is
helpful for removing stubborn wrinkles. The jet of steam feature can be used only in
the" & " indication area of the temperature selector dial when steam or dry ironing
(If used at lower setting, water spotting will occur because the iron is not hot enough
to change water to steam). If you have not used the "Jet of Steam" feature for a long
time, it is necessary to clean the inside of the iron before using this feature on any
clothes to be ironed. Simply test the "Jet of Steam" feature several times away from
the ironing board and clothes to be ironed. This will prevent brown spotting or water
spotting on the clothes.