Craftsman HIGH PRESSURE WASHER 580.76225 Operating instructions

Add to my manuals
28 Pages

advertisement

Craftsman HIGH PRESSURE WASHER 580.76225 Operating instructions | Manualzz

Owner's anual

CRAFr$1vlnN+

6.75 HORSEPOWER

2200 PSi 2.2 GPM

HiGH PRESSURE WASHER

CAUTION: Before using this product, read this manual and follow all Safety Rules and

Operating Instructions.

t/>

HOURS: Non. - Fri. 8 a.m. to 5 p.m. (CST)

PRESSURE WASHER j

CUSTOMER

HELPLINE

SEARS, ROEBUCK and CO., Hoffrnan Estates, IL 60179 U.S.A.

Part No. B2620 DraI_ 0 (2/5197)

SAFETY RULES ............................

ASSEMBLY ..............................

OPERATION .............................

MAINTENANCE ........................

3

4-5

6-9

10-13

STOP,AGE ...............................

TROUBLESHOOTING .......................

REPLACEMENT PARTS ...........

HOW TO ORDER PARTS ............

14

15

: ......

16-27

BACK PAGE

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER

For one year from the date of purchase, when this Craftsman High Pressure Washer is maintained and operat-

ed according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in matedal and workmanship.

if this high pressure washer is used for commercial purposes; this warranty applies for only 90 days from the

date of purchase, tf this high pressure washer is used for rental purposes, this warranty applies for only 30 days after date of purchase.

This warranty does not cover:

o ..Expendable items such as spark plugs and air filters, which become worn during normal use. o Repairs necessary because of operator abuse or negligence, includingdamage resultingfrom no water being supplied to pump or failure to maintain the equipment according to the instructionscontained in the owner's manual.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE

NEAREST SEARS SERVICE CENTER OR DEALER IN THE UNITED STATES.

This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

SEARS, ROEBUCK AND CO., D/817 WA, Hoffman Estates, IL 60179

_

NOT CONTACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP,

CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CAN-

TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER.

AUTION: Before using this product,

Rules and Operating instructions.

o Engine exhaust gases contain DEADLY carbon monoxide gas. This dangerous gas, if breathed in sufficient concentrations, can cause unconsciousness or even death.

Operate this equipment only in the open air where adequate ventilation is available.

o Gasoline is highly FLAMMABLE and itsvapors are

EXPLOSIVE. Do not permit smoking, open flames, sparks or heat in the vicinity while handling gasoline. Avoid spilling gasoline on a hot engine. Allow unit to coot for 2 minutes before refueling. Comply with all laws regulating storage and handling of gasoline.

o Locate this pressure washer in areas away from combustible materials, combustible fumes or dust.

The high pressure equipment is designed to be used with

Sears authorized parts only. if you use this equipment with parts that do notcomply with minimum specifications, the user assumes all risks and liabilities.

° Some chemicals or detergents may be harmful if inhaled or ingested,causing severe nausea, fainting or poisoning.

The harmful elements may cause property damage or severe injury.

Do not allow CHILDREN to operate the Pressure Washer at any time.

o Operate engine only at governed speed. Running the

engineat excessive speeds increasesthe hazard of personal injury.Do net tamper with parts which may increase or decrease the governed speed.

o Do not wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts. o Before starting the Pressure Washer in cold weather, check all parts of the equipmentand be sure ice has not formed there.

o Units with broken or missing parts, or without protecWe housing or covers should NEVER be operated.

• The muffler and air cleaner must be installed and in good condition before operating the Pressure Washer. These components act as spark arrestors if the engine backfires.

o Check the fuel system for leaks or signs of deterioration such as chafed or spongy hose, loose or missing clamps

or damaged tank or cap. Correct all defects before operat-

ing the Pressure Washer.

o Do not spray flammable liquids.

o Never allow any part of the body to come in contactwith the fluid stream. DO NOT come in contact with a fluid stream created by a leak in the high pressurehose.

o High pressurestreams of fluid this equipment produces can pierce skin and its underlyingtissues, leading to serious injury and possible amputation.

o Never aim tile gun at people, animals or plants.

High pressurespray can cause paint chips or other pa_cies to become airborne and fly at high speeds.

o Nways wear eye protection when you use this equipmentor when you are in the vicinity where the equipmentis in use.

, Operate the pressure at no more than the PSI fluid pressure rated for your pressurewasher.

o Never move the machine by pulling on the high pressure hose. Use the handle provided on the top of the unit.

o Always be certain the spray gun, nozzles and accessories

are correctly attached.

• Never use a spraygun which does not have a tri_lgerlock or trigger guard in place and in working order.

• Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read all instructionswith the mask so you are certain the mask will provide the necessary protection against inhalingharmful vapors.

= High pressurespray may damage fragile items including glass. Do not point spray gun at glass when in the jet spray mode.

• Keep Me hose connected to machine or the spray gun while the system is pressurized. Disconnecting the hose while the unit is pressurized is dangerous.

o Hold the spray gun firmly in your hand before you start the unit. Failure to do so could result in an injuryfrom a whipping spray gun. Do not leave the spray gun unattended while the machine is running.

• The cleaning area should have adequate slopes and drainage to reduce the possibilityof a fall due to slippery surfaces.

= Keep water spray away from electric wiring or fatal electric shock may result.

• Do not adjust unloader valve to a pressure in excess of machine rating.

• Do not secure trigger gun in the pull-back (open) position.

= Do not by-pass any safety device on this machine.

o The muffler and engine heat up during operation and

remain hot immediately after shutting it down. Avoid contact with a hot muffler or engine or you could be severely bumed.

MAINTENANCE AND STORAGE:

* Operate and storethis unit on a stable surface.

, High pressure hose can develop leaks from wear, kinking, abuse, etc. Water spraying from a leak is capable of injecting material into skin. Inspect hose each time before using

it. Check all hoses for cuts, leaks, abrasions or bulging of cover, or damage or movement of couplings. If any of these conditions exist, replace hose immediately.Never repair high pressure hose. Replace it with another hose that meets minimum pressure rating of your pressure washer.

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.

IT MEANS "ATTENTION!I!

BECOME ALERT!H

YOUR SAFETY iS INVOLVED."

I

I

CARTON CONTENTS

The following parts are shipped loose with your pressure washer:

=' Main Unit-- pressure washer with wheels, guide handle.

o High Pressure Hose

Parts Box #1 (which includes items listed below)

• Rotating Brush

• Vehicle/Boat Wash

® House/Multi-purposeWash

® Parts Box #2(which includes items listed below) o Adjustable Nozzle

,, Turbo Nozzle

,, Spray Gun

,, Nozzle Extension

° Wire Form

Motor Oil

° Manual Bag (which includesthe items listed below)

= Owner's Manual

, Nozzle Cleaning Kit

• "O"-Ring Kit

Become fam']iiar with each piece before assembling the pressure washer. Check all contents against the illustration on Page 6. if any parts are missing or damaged, call the Pressure Washer Helpline at 1-800-222-3136,

TO REMOVE PRESSURE

CARTON

WASHER FROM

Remove parts boxes included with pressure washer.

The high pressure hose is Packed in the bottom of the carton. Remove the hose.

= Slice two corners at handle end of carton from top to bottom so the panel can be folded down flat.

° Raise handle, secure in place with the locking caps and roll the pressure washer out the open end of the carton.

Locking Caps

How TO SET UP YOUR PRESSURE WASHER

For the most part, your Craftsman High Pressure Washer

has been assembled at the factory. You must, however, attach the wire form, assemble the spray gun, and attach the high pressure hose to the pump and spray gun.

,, While facing the rear of the Pressure Washer, insert

the wire support with the longer arm positionedon the left. From this view the hook should resemble a "J".

/ o Cut tie wrap on chemicalinjection tube. Remove chemical injection filter, thread chemical injec_ontube through the wire form and reinsert filter into tube.

° Check carton for additional loose parts.

* Cut the tie wraps on the high pressure hose and connect high pressure hose to gun. Tighten by hand.

° Place assembled spray gun on holder.

, Place turbo nozzle in grommet hole in base.

o Remove plastic cap and connect high pressure hose to pump. Tighten by hand.

Attach nozzle extension to spray gun.

Attach High

Pressure hose here

Attach adjustable nozzle to the nozzle extension.

CHECKLIST

Before you operate your new high pressure washer please review the following checklist:

• All assembly instructions have been completed.

• The high pressure hose connections to the spray gun and to the pump are tight and secure.

While learning how to use your high pressure washer, pay extra attention to the following important item:

Engine oil is at proper level

Important: Any attempt to crank or start the engine before it has been properly serviced with the recommended oil may result in an engine failure. See Page

9 for instructions on adding oil and proper oil specifications.

Important: The water supply to your pressure wash- er must be connected and turned on prior to starting your engine.

° Be sure gas tank is filled properly with clean, fresh, unleaded gasoline.

o Become familiar with all controls - their location and function. Operate those controls before starting the engine.

5

KNOW YOUR HIGH PRESSURE WASHER

Read this owner's manual and safety rules before operating your high pressure washer. Compare the illustra-

tions with your high pressure washer to familiarize yourself with the locationsof various controls and adjustments.

Save this manual for future reference.

Chemical Injection

Tube and Filter

High Pressure Hose

Spray Gun

Nozzle Extension

Gas Cap

Air Filter

Engine Throttle Control

Adjustable Nozzle

Water Inlet

Rotating Brush

Primer Bulb

High Pressure

Outlet

Pump

Car Wash

" House Wash

Pump - Develops high water pressure.

Engine Throttle Control - Sets engine in starting mode

for recoil starter; STOPS running engine.

Primer Bulb -- Prepares a cold engine for starting.

Recoil Starter -- Used for starting the engine manually.

Air Filter -- Dry type filter element limitsthe amount of

dirt and dust that gets in the engine.

Rotating Brush Adapter

Turbo Nozzle -- Attaches to the nozzle extension and creates a high pressure stream that rotates in a circular pattern.

Adjustable Nozzle -- Attaches to the nozzle extension and adjusts the spray pattern to be either a low pressure stream or a high pressure stream. Twisting the nozzle adjusts the narrow spray pattern to a fan spray pattern.

Note: You can only siphon detergent in the low pressure mode.

Spray Gun -- Controlsthe application of water onto

cleaning surface with trigger device. Includes safety latch.

Chemical Injection Tube and Filter -- Mixes water and

detergent in outlet water flow.

Car Wash -- Use the concentrate to wash your car or boat.

House Wash -- Use the concentrate to wash your

House.

High Pressure Outlet -- Connection for high pressure hose.

Water inlet -- Connectionfor garden hose.

Nozzle Extension -- Attach one end to the spray gun.

Attach the other end of the nozzle extension to either the adjustable nozzle, turbo nozzle or rotating brush adapter.

Rotating Brush -- Use this brush for automatic scrub- bing of surfaces. Attaches to the nozzle extension. Note:

When attaching to nozzle extension, you must use the accessory adapter.

High Pressure Hose -- Attach one end to the pump,

Attach the other end to the spray gun,

Oil Fill Cap -- Fill engine with SAE 30 oit here.

Gas Cap -- Fill gas tank with unleaded gasoline here,

Rotating Brush Adapter -- Allows the rotatingbrush to

be attached to the nozzle extension.

6

HOW TO USE YOUR PRESSURE WASHER

IF YOU HAVE ANY PROBLEMS operating your pressure washer, please call the pressure washer helpline at 1-800-222-3136.

A DANGER!

NEVER adjust spray pattern

when spraying. NEVER put hands in front of spray nozzle to adjust spray pattern.

You could be injured.

HOW TO USE THE ADJUSTABLE NOZZLE

One of the nozzles you can attach to the nozzle extension is the adjustable nozzle. You can slide the adjustable nozzle forward and backward to adjust the spray pattern to be either high pressure or tow pressure. You can also twist the adjustable nozzle from side to side to adjust the spray so it is concentrated in a stream pattern or expanded into a fan pattern. o Slide the nozzle forward to adjust the spray to low pressure mode. Slide the nozzle backward to achieve high pressure,

• If you get spray nozzle too close, especially using high pressure mode, you may damage the cleaning surface.

APPLYING DETERGENT AND CLEANING WiTH

ADJUSTABLE NOZZLE

IMPORTANT: Use soaps designed specifically for pressure washers. Household detergents could damage the pump.

IMPORTANT: You must attach all hoses before you start the engine. Starting the engine without all the hoses connected and without the water turned ON

will damage the pump.

To apply detergent follow these steps:

° Prepare the detergent solution as required by the

job. (For the enclosed bottles of detergent, add the 8 ounces of chemical to a 1 gallon plastic bottle with handle (not included). Fill the rest of the bottle with water.) o Hang the detergent solution on the "J" hook on

the wire form on the guide handle.

Place small filter on the chemical injectiontube into the detergent container.

Slide nozzle backward to place in high pres- sure mode.

Slide nozzle forward for low pressure mode.

Twisting the nozzle adjusts the spray pattern from a narrow pattern to a fan pattern.

Twist nozzle counterclockwise for fan spray pattern.

Twist no_te clockwise for narrow spray pattern.

For most effective cleaning, keep spray nozzle between 8 to 24 inches away from cleaning surface.

o Slide the adjustable nozzle forward to low pressure mode. Detergent cannot be applied with nozzle in high pressure position.

Note: The first step involves applying an appropriate detergent/solvent solution to penetrate and loosen grime. The detergent is applied at tow pressure to avoid splashing, overspraying and waste. Leave the solution on surface for 3 to 5 minutes to allow solution to work.

o o

Note: The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean.

Review the use of the adjustable nozzle.

Connect garden hose to water inlet (see 'q'O

START PRESSURE WASHER"), check that high

pressure hose is connected to spray gun and pump (see ASSEMBLY), and start engine.

For cleaning, start at lower portion of area to be

washed and work upward, using long, even over- lapping strokes.

Allow the detergent to soak in between 3-5 minutes before washing and rinsing.

RINSING WiTH THE PRESSURE WASHER

WARNING Be extremely careful if you must use the pressure washer from ladder, scaffolding or any other relatively unstable location. Pressure in a running washer builds in

the wand as you climb. When you press the trigger, the recoil from the initial spray could force you to fail, or if you are too close to the cleaning surface, high pressure could force you off a climbing apparatus.

• Hook up the water supply and start your pressure

washer (see TO START THE PRESSURE WASHER).

• Slide adjustable nozzle back to high pressure position and wait for detergent to clear. Detergent will not flow when in the high pressure mode.

= When detergent has cleared you may want to expand the spray pattern for a more gentle rinsing action.

Start at top of area to be rinsed, working down with same action as for cleaning.

You can also stop detergent from flowing by simply

removing_phon from bottle.

HOW TO USE ADJUST PRESSURE

THE PRESSURE CONTROL KNOB

USING

Located on the pump is a pressure controlknob. You can increase and decrease the pressure of the spray by turning the knob clockwise or counterclockwiserespectively.

_,The knob is set at maximum pressure at the factory.

HOW TO USE THE TURBO NOZZLE.

The turbo nozzle rotates the high pressure stream in a rapid circular pattern. This increases the cleaning effectiveness of the high pressure spray, Attach the turbo nozzle on the end of the nozzle extension.

The high pressure spray is most effective when the tip of

the wand is held between 8 to 24 inches from the surface being cleaned.

Important: The turbo nozzle produces an extremely high pressure spray which is capable of removing paint and cuffing holes through surfaces if held too close. Always

make sure the surface you will clean will not be damaged

by the high pressure spray.

HOW TO USE THE ROTATING BRUSH

Your pressure washer comes equipped with a rotating

brush. Use the brush to clean especially dirty surfaces, it

is a soft bristle brush with feathered ends that will not scratch surfaces.

To connect the rotating brush to the spray gun: o o

Attach the accessory adapter to the rotating brush.

After attaching the accessories adapter onto the rotat-

ing brush, attach the accessory adapter to the nozzle extension.

After attaching the accessories adapter onto the nozzle extension, attach nozzle extension onto spay gun.

Note: The rotating brush operates in low pressure setting allowing you to dispense chemical with the brush.

BEFORE STARTING THE PRESSURE WASHER

To operate the engine you wilt need to do the following:

ADD ENGINE OIL

Use only high quality detergent oil rated with API

service classification SF or SG rated SAE 30 weight.

Use no special additives.

o Place pressure washer on a level surface

, Clean area around oil fill and remove oil dipstick.

o Wipe dipstick clean.

° Pour oil from enclosed bottle into the oil fill opening until oil reaches FULL mark on the dipstick. Stop and check the oil level periodically. DO NOT OVERFILL.

= Install oil dipstick, hand tighten securely.

Check oil level often during engine break in.

ADD GASOLINE

Use fresh, clean, unleaded regular, unleaded premium, or reformulated automotive gasoline only.

Do not use leaded gasoline.

A

DANGER! NEVER fill fuel tank indoors.

NEVER fill fuel tank when engine is run-

ning or hot, DO NOT light a cigarette or

smoke when filling the fuel tank.

DANGER! Do not overfill the fuel tank.

Always leave room for fuel expansion.

Wipe any fuel spillage from engine and equipment before starting engine

Note: Do not use gasoline containingmethanol (wood alcohol). Gasoline containing up to 10% ethanol or grain alcohol ("Gasohol"), or up to 15% MTBE (Methyl Tertiary

Butyl Ether), may be used but requires special care when engine is unused for extended periods.

See "Storage" instructionson Page 15.

Clean area around fuel fill cap, remove cap.

o Add "UNLEADED" regular gasoline, slowly, to fuel tank.

Important: Never mix oil with gasoline.

, Install fue! cap and wipe up any spilled gasoline.

TO START YOUR PRESSURE WASHER

You have assembled your high pressure washer and have prepared the engine for starting. You are now ready to clean your car, boat or whatever you plan to clean.

Ptace the pressure washer in an area close enough

to an outside water source that can flow at a rate of at least 2.2 gallons per minute. Connect a garden hose to the water spout.

Check that the high pressure hose is tightly connect- ed to the spray gun and to the pump. See ASSEM-

BLY section for illustrations.

e Pull back on the locking collar to remove the female quick-connect from pump.

Assembled

Quick-Connect

Pull back on locking collar to separate

Disassembled male end

Disassembled female end

Note: You wilt also need to pull back on the lockingco!lar to attach the female quick-connect.

Check inlet screen. If the screen is dirty, clean before attaching to garden hose. If the screen is damaged, Do not connect to the garden hose.

Replace with the inlet screen provided in the o-ring kit or cal! 1-800-366-PART to order a replacement

(pln B2384).

Attach the female quick-connect to garden hose and then attach the garden hose to the water inlet. Make sure the quick-connect is locked together.

9

Turn on the water.

IMPORTANT: Do not run pump without the water supply connected and turned on. You must follow this caution or the pump wilt be damaged.

• Move the Throttle Control Lever to the 'Fast' position

® Push primer bulb 3 times. Wait about two 2 seconds between each push. In cold weather, (55°F/13°C or below) push 5 times.

Note: Do not use primer to restart a warm engine after a short shut down.

Positionthe nozzle in the low pressure mode (nozzle

slid forward) and squeeze the triggeron the spray gun to relieve the air pressure caused by turning ON the water. Water will spew out the gun in a thin

stream. Continue to hold trigger until you have a steady stream of water and no air remains in the system. This will make it easier to pull start the engine.

Release the trigger.

= Engage the safety latch on the gun.

Grasp rope handle and pull slowly until you feet some resistance. Then pull cord rapidlyto overcome com- pression, prevent kickback and start the engine. Let

rope return to starter slowly ................

Note: Always keep the Throttle Control Lever in the

'Fast' position when operating the pressure washer.

Note: if after 3 pulls the engine fails to start, prime the

engine again, purge the gun and pull the recoil starter

handle rapidly (Max. 3 pulls).

HOW TO STOP YOUR PRESSURE WASHER

Move the Throttle Control Lever to the 'Slow' posi- tion.

Wait for the engine to idle down.

.

Move the Throttle Control Lever to the 'Stop' position,

• Simply shutting off the engine will not release

pressure in the system. Squeeze trigger on the spray gun to relieve pressure in the hose.

Note: A small amount of water wilt squirt out from the spray gun when you release the pressure.

SIPHONING

We recommend that you DO NOT siphon standing water for your water supply. Contaminated, brackish or dirty

water can damage the pump. Connect only to household water supply.

TIPS

, Never use the garden hose inlet to siphon detergent

or wax .......

If you have the spray nozzle too far away, the clean- ing will not be as effective.

]0

CUSTOMER RESPONSiBiLITIES

MAINTENANCE SCHEDULE

FiLL IN DATES AS YOU COMPLETE

REGULAR SERVICE

HOURLY OPERATING INTERVAL

MAINTENANCE TASK

PRESSURE WASHER

Before Each

Use

Houm or

Every" 100

Hours or

Yearly

SERVICE DATES

onquick,-connect.

Checkspraygunandassemblyforleaks.

Purgepumpofairandconta_nants.

ENGINE

Prepare for storage.

_ X

X

Xt

X

X

X

X*

X',t _" x

Prepare unit for storage if it is to

remain idle for longer than 30 days.

,,,,,,,,,, ,, • , i i

I" Clean if clogged, Replace if perforated or tom,

* Change oil after first 2 hours then 25 thereafter. Change sooner when under dirty or dusty conditions.

"* Clean more often under dirty or dusty conditions.

GENERAL RECOMMENDATIONS

The warranty of the high pressure washer does not cover items that have been subjected to operatorabuse or neg- ligence. To receive full value from the warranty, operator

must maintain high pressure washer as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your high pressure washer,

All adjustments in the Service and Adjustments section of this manual should be made at least once each season.

Once a year you should clean or replace the spark plug and clean or replace the air filter and check the gun and wand assembly for wear. A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer.

PRODUCT SPECIFICATIONS

Pressure Washer Specifications

PRESSURE 2200 psi

FLOW RATE 2.2 GPM

DETERGENTMIX

WATER SUPPLY

TEMPERATURE

Use undiluteddeterqent..........

Not to Exceed !40°F

Engine Specifications

ENGINE MODEL

RATED HORSEPOWER

DISPLACEMENT

SPARK PLUG: Type:

Set Gap to:

GASOLINE CAPACITY

OIL

SOLID STATE IGNITION

AIR GAP

Craftsman

6,75

172cc

Champion RN4C or equivalent

0,030 inch l'0,76mm)

1,5 U.S, quart

SAE 30 weiaht

0.0125 inch tn the State of California a spark arrestor is required by law (Section 4442 of the California Public Resources

Code). Other states may have similar laws, Federal laws apply on federal lands.

Note: tf you equip the engine of your pressure washer with a spark arrestor muffler, the spark arrestor must be maintained in effective working order by the owner/operator.

You can order a spark arrestor through your Sears

Service Center.

11

BEFORE EACH USE

Check water inlet screen for damage.

Check high pressure hose for leaks.

° Check detergent inlet hose and filter for damage.

Check gun and wand assembly for leaks.

Purge pump of air and contaminants.

• Check engine oil level.

PRESSURE WASHER MAINTENANCE

Check and Clean Inlet Screen: Remove quick-connect and examine inlet screen on the female connector. Clean if it is clogged or replace if it is tom.

Check High Pressure Hose: High pressure hose can

develop leaks from wear, kinking, abuse. Inspect hose each timebefore using it. Check for cuts, leaks, abrasions or bulgingof cover, or damage or movement of couplings.

If any of these conditionsexist, replace hose immediately.

,_ DANGER: Water spraying from a leak is

NEVER repair high pressure hose. Replace with hose that meets minimum pressure rat-

-_ ing of your pressure washer.

o

Check Detergent Hose: Examine the filter on the detergent hose and clean if clogged. Hose should fit tightly on

barbed fitting. Examine hose for leaks or tears. Replace

the filter or hose if either is damaged.

Check Gun and Wand: Examine hose connection to gun and make sure it is secure. Test trigger by pressing it and makingsure it springs back into place when you release it.

Put safety latch in UP positionand test trigger. You should not be able to press trigger.

Purge Pump of Air and Contaminants

To remove the air from the pump, follow these steps:

.

Set up the pressure washer as described in the

ASSEMBLY section and connect the water supply.

° Remove'the nozzle extension from the gun.

o Pull the trigger on the gun and hold.

To remove the contaminants from the pump, follow these steps:

• Set up the pressure washer as described in the

ASSEMBLY section, and connect the water supply.

• Remove the nozzle attachment from the gun.

° Start the engine according to instructions in OPER_,-

TION section.

O

Putt the trigger on the gun and hold.

When the water supply is steady and constant, engage the safety latch and refasten the nozzle attachment.

ENGINE MAINTENANCE

CHECKING OIL LEVEL

Oil level should be checked prior to each use or at least every 5 hours of operation. Keep oil level maintained.

CHANGING ENGINE OIL

Change engine oil after first 2 hours then every 25 hours thereafter. If you are using your pressure washer under extremely dirty or dusty conditions, or in extremely hot weather, change oil more often.

Change oil while engine is still warm from running, as follows:

Disconnect spark plug wire from spark plug and keep it away from spark plug.

Before you tip the pressure washer to drain oil, drain fuel tank by running pressure washer until fuel tank is empty.

Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

Tip your pressure washer to drain oil completely from

the oil fill tube into a suitable container. When crankcase is empty, return the pressure washer to upright position.

Fill engine crankcase with recommended oil until oil level is at FULL point on dipstick. Do not overfill above that mark. POUR SLOWLY.

When engine crankcase is filled to proper level, install and tighten oil cap/dipstick.

SERVICE AIR CLEANER

Your engine will not run properly and may be damaged if you run it with a dirty air cleaner.

Replace the air cleaner once every 100 hours of opera- tion or once each year, whichever comes first. Replace more often if operating under dirty or dusty conditions.

Replacements are available at your local Sears

Authorized Service Center.

Important: Do not attempt to clean or oil filter.

Important: Never run engine without complete air cleaner installed on engine.

To clean or replace the air cleaner, follow these steps:

TURN COVER 3"0 THE LEFT

(COUNI_RCU:X;k_,_)'tO

_P,JRN GOVER

" .1'0

12

o o o

Turn cover to the left (counterclockwise) and remove it and filter from flange. Discard filter.

Clean cover and flange thoroughly.

Insert new filter into cover.

Position cover and filter firmly against flange with tab on cover inserted into lower left comer of slot in flange.

Push cover firmly against flange and turn it to the right (clockwise) as far as it will go. Be sure retainers are locked around flange.

CLEAN/REPLACE SPARK PLUG

Change the spark plug every 100 hours of operation or once each year, whichever comes .first. This will help your engine to start easier and run better. Replace with champion RN4C or equivalent type spai'k plug.

Clean area around spark plug

Remove and inspect spark plug.

Replace spark plug if electrodes are pitted, burned or porcelain is cracked. For replacement use

Champion RN4C only.

Check electrode gap with wire feeler gauge and set gap at 0.030 (0.76mm) if necessary.

SET PLUG GAP AT 0.030

inch

(0.76 ram) o

Shut off the engine and turn off the water supply.

Separate the nozzle from the nozzle extension,

Rotate to stream setting.

,, Remove orifice from the end of the nozzle using the allen wrench included with the kit or a 2ram or 5/64 allen wrench.

• Use the wire included in the kit or a small paper clip

to free the foreign materials clogging or restricting the nozzle.

insert wire into orifice and turn back and forth to clear obstruction.

Remove additional debris by back flushing water supply through wand. Back flush between 30 to 60 seconds. Turn wand to stream spray and move nozzle from tow to high pressure while flushing.

NOZZLE MAINTENANCE

If the nozzle becomes restrictedor clogged with foreign materials, such as dirt, excessive pump pressure may develop. A partially clogged nozzle can cause a pulsing sensation during use. This generally is not a pump related problem, but rather a clogged or partially restricted nozzle.

If the nozzle becomes clogged or partially restricted, immediately clean the nozzle with the kit included with your pressure washer by following these instructions:

Reinstall orifice into nozzle. DO NOT overtighten. o Reconnect nozzle to nozzle extension.

• Reconnect the water supply, turn ON the water, and start the engine.

Test the pressure washer by operating with nozzle in the high and the tow pressure positions.

!3

1 O-Ring (p/n B2386) for the outside of the Male

Quick-Connect,

O-RING MAINTENANCE

Through the normal operation of your pressure washer,

O-Rings, which keep the connections of the hoses and

gun tight and leak-free may become worn or damaged.

Provided with your pressure washer is an O-Ring

Maintenance Kit which provides replacement O-Rings,

Rubber Washer and Quick Connect filter.

Parts in the O-Ring Kit Include:

2 O-Rings (pin 97837) for each end of the nozzle extension,

0

1 Water Inlet Screen (p/n 132384)for the Female

Quick-Connect,

= 2 O-Rings (pin B2264) for the ends of the high pressure hose.

1 o-ring (p!n B2688) for the connection end of the .....

rotating brush.

/

O-Ring

Note: The above two O-Rings are close in size. Please

match carefully to assure proper O-Ring usage.

.

1 Rubber Washer (pin B2385) for the inside of the

Male Quick-Connect.

To remove a worn or damaged O-Ring: o Use a small flathead screwdriver to get underneath the O-Ring and pry it off.

]4

AFTER EACH USE

Water should not remain in the unit for long periods of time.

Sediments of minerals can deposit on pump parts and

"freeze" pump action. Follow these procedures after every use:

Flush detergent hose by placing the injectorfilter into a pail of clear water while running Pressure Washer with nozzle in low pressure mode. Flush until you can see clear water running through the tube.

Shut off the engine and let it coot, then remove all hoses,

CAUTION: Be sure throttle lever is in

"STOP" position before you continue. If you start engine without the proper water supply connected, you can damage the pump.

o

To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Follow these instructions:

PROTECT FUEL SYSTEM o Remove all gasoline from the fuel tank to prevettt gum deposits from forming on these parts and causing possible malfunction of engine.

DANGER: Drain fuel into approved consure engine is cool. Do not smoke.

Run engine until engine stops from lack of fuel. Make

sure you have water supply to pump inlet connected and turned ON.

Empty the pump of all pumped liquids by pulling recoil handle about 6 times. This should remove most of the liquid in the pump.

Coil the high pressure hose and inspectit for damage.

Cuts in the hose or fraying of it could result in leaks and toss of pressure. Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose. Replace the hose with the genuine

Craftsman part.

Drain water from hose and properly hang it on the wire support provided on the guide handle.

Note: tf "Gasohol" has been used, complete above instructions and then put 1/2 pint of unleaded gasoline

intofuel tank and repeat above instructions.

Note: Fuel stabilizer (such as STA-BIL) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Run engine at least 10 minutes after adding stabilizer.

CHANGE OIL

While engine is still warm, drain oil from crankcase. Refill with recommended grade. (See Changing Oil Level on

Page 12.)

OIL CYLINDER BORE

DANGER: NEVER store engine with fuel in I

tank indoors or in enclosed, poorly ventilat- I ed areas where fumes may reach an open flame, spark or pdot light as on a furnace, water heater, clothes dryer or other gas appliance, o Remove spark plug and squirt about 1 ounce (30 rnl) of engine oil into the cylinder. Cover spark plug hole with rag. Crank slowly to distribute oil.

l_k AUTION: Avoid spray from spark plug

I

Install spark plug. Do not connect spark plug wire. • Store in a clean, dry area.

,_ CAUTION: You must protect your unit will permanently damage your pump and render your unit inoperable.

WINTER STORAGE

To protect the unit from freezing temperatures:

Draw RV antifreeze (antifreeze without alcohol) into the pump by pouring the washer fluid into a 3-foot section of garden hose connected to the inlet adapter and pulling the recoil handle twice.

LONG TERM STORAGE

If you do not plan to use the PressureWasher for more than

30 days, you must prepare the engine for longterm storage.

Note: As always, prepare the pressure washer pump as you would after each use.

OTHER

@ o

Do not store gasoline from one season to another,

Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

If possible, store your unit indoors and cover it to give protection from dust and dirt. BE SURE TO EMPTY

THE FUEL TANK.

°

Cover your unit with a suitable protective cover that does not retain moisture.

IMPORTANT: NEVER cover your pressure washer while

engine and exhaust area are warm,

15

PROBLEM

Pumphasfollowingproblems: failureto producepressure,or erraticpressure,chattering,lossof pressure,low watervolume.

Detergentfails to mix with.

spray=:

CAUSE

1. Nozzlein lowpressuremode.

2. Water inletis blocked,

3.

Inadequatewatersupply

4.

Inlet hose is kinked or leaking

5.

Clogged water inlet screen.

6.

Water supply is over 140°F.

7.

Outlet hose is blocked.

8.

Outlet hose leaks.

9, Gun leaks.

10. Nozzle is obstructed,

1!.

Pump is faulty.

1.

Detergent line isnot submerged. in detergent spray

2.

Chemical filter is clogged.

3; Nozzleis in highpressuremode.

CORRECTION

1.

Pull nozzlebackwardfor high pressuremode.

2, Clearinlet

3.

Provideadequatewaterflowat least 2.2 gpm.

4, Straighteninlethose,patchleak.

5.

Replace/ cleanwaterinletscreen.

6.

Providecoolerwatersupply,

7. Clear blocksin outlethose,

8.

Replaceoutlethoseif leaking.

9.

Replaceo-ringor gunif necessary.

10. Clearnozzle.

11. ContactSearsServiceDepartment.

1.

Insert chemicalline intodetergent.

2.

Cleanor replacefilterldetergent line,

3. Push nozzleforward for low pressuremode.

Enginerunsgoodwhen notspraying

butdies whenyou beginto spray.

Engine speed is too slow.

Enginewiltnot start;or starts and runsrough

1.

Dirty air cleaner

2.

Out of gasoline,

3.

Stale gasoline,

4.

Spark plug wire not connected to spark plug.

5.

Bad spark plug.

6.

Water in gasoline,

7.

Overchoking or ftooded

8.

Excessivelyrichfuel mixture.

9.

Intakevalvestuckopenor closed.

10. Enginehas'lostcompression.

Contact SearsServiceDepartment. i.

Cleanor replaceair cleaner,

2.

Fill fuel tank,

3.

Drain gas tank;fill withfresh fuel.

4.

Connectwireto sparkplug.

5.

Replacesparkplug.

6. Drain gastank;fill withfresh fuel.

7, Set enginethrottlecontrolleverto fast position,chokein run position,

8.

ContactSearsServiceDepartment.

9.

ContactSearsServiceDepartment,

10. ContactSearsServiceDepartment.

Engineshutsdownduring operation

Enginelacks power.

1, Out of gasoline.

2.

Air filter dirty

Dirty air filter,

1, Fill fueltank.

2, ReplaceAirfilter.

Replaceair filter.

]6

17

CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200

Craftsman 4-C¥cte Engine 143.986714

1111

161

157

2O

119 i01

27g

266

178

2O7

42

41

43

45 46

17

"_ 310

==_-3o9

""305

",3_

]8

46

48

50

52

42

42

42

43

45

40

40

4!

41

41

Item

6

7

I

2

Part#

36835A

26727

33734

36557

12 32447

12A 36558

19

20

30

40

12B 36694

14

15

16

17 t8

28277

30589

34839A

31335

651018

36281

32600

37208

35544A

35545A

35546

35541

35542

35543

35547A

35548A

35549

20381

32B75A

32610A

35616

37011

29914

CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,762200

Craftsman 4=Cycle Engine 143.986714

Description

Cylinder (Incl. 2 &. 20)

Dowel Pin

Breather Element

Breather Ass'y.

(Incl. 6 & 12A)

Breather Tube

Breather Cover & Tube

(Znct. 12B)

Breather Tube Elbow

Washer

Governor Rod (Incl. 14)

Governor Lever

Governor Lever Clamp

Screw, Torx T-15, 8-32 x

19/64"

Extension Spring

Oil Seal

Crankshaft

1

1

Piston, Pin & Ring Set

(Std:)

Piston, Pin & Ring Set'

(.olo" os)

Piston, Pin & Ring Set

(.020" OS)

Piston & Pin Ass'y. (Std.)

Pistcrn & Pin Ass'y.

(.010" OS) (incl. 43)

Piston k Pin Ass'y.

(.020" OS) (Incl. 43)

Ring Set (Std.)

Ring Set (.010" OS)

Ring Set (.020" OS)

!

I

1

Piston Pin Retaining Ring 2

Connecting Rod Ass'y.

(ZncL 46) 1

Connecting Rod Bolt

Valve Lifter

2

2

1

1

1

1

1

1

Camshaft (MCR)

Oil Pump Ass'y.

1

1

I

1

1

1

1

2

1

I

!

1

1

1

1

Qty.

l_m

69

70

Part#

37130

37190

72 36083

72A 28534

75 28460

80

81

82

30574A

30590A

30591

83

86

89

90

92

30588A

650488

610961

611213

650815

93 650816 t00 34443B

101 610118

103 651007

110 36230

119 36738

120 36721

125 36471

125 36472

126 29314B t26 29315C

130 650912

130A 650999

135 34645

150 31672

151 31673 t53 36649

154 650913

Description

Qty.

Mounting Flange Gasket

Mounting Flange

(Incl. 72 thru 83,306)

Oil Drain Plug

Oil Drain Plug

Oil Seal

Governor Shaft

Washer

1

Governor Gear Ass'y.

(incL 81)

Governor Spool

Screw, 1/4-20 x 1-1/4"

Flywheel Key

Flywheel

Bellevilte Washer

Flywheel Nut

Solid State ignition

Spark Plug Cover

Screw, Torx "1"-15,

10-24 x 15(16"

Ground Wire

2 t

Cylinder Head Gasket

Cylinder Head

Exhaust Valve (Std.)

(Incl. 151)

Exhaust Valve (t/32" OS)

(Inc!. 151)

Intake Valve (Std.)

(Incl. 15t)

Intake Valve (1/32" OS)

(Inc!. 151)

1

1

1

1

Screw, 5/16-18 x 1-1(2" 4

Screw, 5!16-18 x 2-41/64" 1

Resistor Spark Plug

1

1

(RN4C)

Valve Spring

Valve Spring Cap

Push Rod Guide

.Rocker Arm Stud

1

2

2

1 t

1

1

6

1

1

1

1

1

1 t

1

1

1

1

1

]9

CRAFTSMAN 2200 PSI HiGH PRESSURE WASHER 580.762200

Craftsman 4-Cycle Engine 143o986714

Item Part# Description

155 35624A

I57 650914

15B 36629

159 35626

Rocker Arm

Lock Nut

Push Rod

1

1

2

Rocker Arm Cover Gasket 1

1 160

161

178

182

184

185

186

187

200

202

35718

30063

29752

30088A

26756

36579

34337

36580

35727

36482

203_ 31342

204 651029

Rocker Arm Housing

Screw, Torx T-30, 114-20 x 1/2"

Nut &. Lock Washer,

114-28

Screw, 114-28 x 1"

Carburetor Gasket intake Pipe

Governor Link

Spacer

Control Bracket

(ZncL 202 thru 205)

Compression Spring

Compression Spring

Screw, Torx T-I0,

5-40 x 71t6"

205 651019 Screw, Torx T-10,

............. 6'32 X 41164 ............

207 34336

209 30200

215 32410

Throttle Link

Screw, 10-24 x 9116"

Control Knob 1

223 651044

224 36581

238 650932

239 34338

241 36919

245 36905

250 36920

260 37180

261 30063

262 650831

Screw, 1/4-20 x 2-25132" intake Pipe Gasket

Screw, 10-32 x 49164"

Air Cleaner Gasket

Air Cleaner Collar

Air Cleaner Filter

Air Cleaner Cover

Blower Housing

Screw, Torx T-30, t/4-20 x 112"

Screw, 114-20 x 1/2"

4

1

1

1

1

2

2

1

1

1

1

2

2

1

1

1

1

1

I

1

1

2

2

1

Qty.

item Part# Description

Qty.

263A 37184

266 651O40

266A 650852

275 36950

276 36949

277 651039

279 650431

Starter Grill

Stud, 1/4-20

Locking Plate

Screw, 114-20 x 2-47/64"

1

1

Nut E Lockwasher, 114-20 1

Muffler (IncL 276 &. 277) 1

1

2

280 37210

285

287

290

292

298

300

3500QA

650926

29774

26460

28763

36916

301 36246

305 35647

Screw, Torx T-25,

10-32 x 5t8"

Heat Shield

I

1

Starter Cup

Screw, 8-32 x 21164"

Fuel Line

Fuel Line Clamp 2

Screw, 10-32 x 35/64" 2

Fuel Tank (Incl. 292 & 301) 1

Fuel Cap

Oil Fill Tube

1

1

"0"-Ring

"0"-Ring

Screw, 10-32 x 1/2"

1

2

1

1

1

1

306 36996

3O7 35499

309 650562

310

313

325

35648

34080

29443

341A 36578

347 651038

370A 36261

370B 35169

380

390

640147

590739

Dipstick

Spacer

Spring Clip

Blower Housing

Support Bracket

Screw, 10-32 x 27/32"

Lubrication Decal

Control Decal

Carburetor (Incl. 184)

Rewind Starter t

1

1

(NOTE: This engine could have been built with

590702 starter).

900 0

900 0

Replacement Engine

Replacement S/B 750835, order from 71-999

0

1

2

1 i

1

1

1

2O

CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580.762200

Craftsman 4=Cycle Engine 143.986714

Item

0

2

4

5

6

16

17

Part#

640147

631615

631767

631184

631183

640070

650506

631807

651025

18

20

20A

630766

640016

640053

Description Qty.

Carburetor ncl. 184 of Engine artsList)

Throttle Shaft & Lever

1

Assembly 1

Throttle Return Spring 1

Dust Seal Washer 1

Dust Seal (Throttle)

Throttle Shutter

Shutter Screw

Fuel Fitting

Throttle Crack

1

1

1

1

Screwlldle Speed

Screw

Tension Spring

Idle Restrictor Screw

Idle Restrictor

Screw Cap 1 i

1

1 item Part# Description

25 631867 Float Bowl

27 631024 FloatShaft

28 632019 Float

29 631028 Float Bowl "0" Ring

30 631021 Inlet Needle, Seat, k Clip (Incl. 31)

31 631022 Spring Clip

35 36045A Primer Bulb/Retainer

Ring

36 632745 Main Nozzle Tube

37 632547 Main Nozzle Tube

1

1

"0"Rin-_q " ' 2

40 640083 High S_eed Bowl Nut 1

44 27110 Bowl Nut Washer 1

47 630748 Welch Plug, Idle

Mixture VVelt

48 631027 Welch Plug,

Atmospheric Vent t

I

1

1

1

1

1

1

2]

CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200

Craftsman 4-Cycle Engine 143.986714

/

Item

0

3

6

8

11

12

13

14

Part#

590739

590740

590616

590617

590618A

59063B

590535

590701

590741

_3

Description .

Qty.

Rewind Starter

Retainer

Starter Dog

Dog Spring

Pulley k Rewind Spring Ass'y

Starter Housing Ass'y_40 degree grommet)

Starter Rope (I-engti-i98 x 9(64" alia.)

Starter Handle

Locking Tab

,

1

1

1

2

2

1

1

1

1

22

CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,7622_

Craftsman 4=Cycle Engine 143.986714

13

_8

_5

_3

Item

4

5

6

7

8

2

3

0

1

11

12

13

Part#

590702

590599A

590600

590696

590601

590697

590698

590699

590700

590703

590535

590701

Description

Qty.

Recoil Starter

Spring Pin (Zncl. 4)

Washer

Retainer

Washer

Brake Spring

Starter Dog

Dog Spring pulley & Rewind Spring Ass'y.

Starter HousingA,ss'y. NO degree

Starter Rope (98 X 9/64 dia.)

Starter Handle grommet)

2

2

1

1

1

0

1

1

1

I

1

1

23

CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580,762200

19

ToA

17 tZ

24

CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580.762200

10

11

12

13 t4

15

16

17

!8

19

20

2I

22

23

24

25

FFEM _

1

NO.

EB2528

2 132619

3

4

5

6

7

8

9

A1803C

EB2534

39414

52858

42909

27007

B2142

754O2

B2168

B1460

B1779

B2347

46476

51767

52857

92235

B1631A

B2623

B2626

91373

79552

96307

A1040B

2

2

2

3

2

2

1

2

1

1

1 t

1

1

1

1

2

2

3

5

2

1

1

1

1 iTEM PART,NO.

BASE, VSPW 26

ENGINE, Tecumseh O1_',/ 27

A1041

A1408

6.75HP

PUMP, Medium Frame

HANDLE

28

29

30

B1232

B1288

21782

HHCS, M8 x 35

NUT, M8 Locking Flange

HHCS, M8 x 30

MOUNT, Rubber Foot

WHEEL, 2"x g' Black

Mag

PUSHNUT, i/2"

HANGER, Hose

31

CAP, Vinyl

COVER, Hinge

CAP, End

CAPLUG

HHCS, M6 - 1.0x 45

NUT, M6 Locking Flange 43

GROMMET, Turbo Nozzle 44

BILLBOARD 45

46 DECAL, Crafcsman2200

PSI

DECAL, Instructions

DECAL, Data

OVERLAMINATE

DECAL, 1-800 #

HOSE, Chemical

47

48

49

50

32

33.

35

36

37

38

39

40

41

42

21781

96382

B2620

B2730

97009

50190

48031

97054

97100

B1969

B1974G

B2370

95587E

97123

B2389

88935

97566

B1736

B1736A

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1 i

1

1

1

1

DESCRI_ON

FILTER, ChemicaI Hose

CAP, Garden Hose Inlet

CLAMP, Hose 7/16"

TAG, Breather Cap

QUICK DISCONNECT,

Female

QUICK DISCONNECT,

Mate

WASHER, M8 Flat

CLAMP, Hose 3/t6"

TAG, Pressure Adjust

CAP, High Pressure

HOSE, 1/4" x 25'

TURBO, Nozzle

GUN, High Pressure

NOZZLE, Adjustable

WAND, Extension

BRUSH, Rotating

ADAPTER, Brush

TAG, Nozzle

WASH, VehideJBoat

WASH, HouseJMuHJ

Purpose

OIL, Engine SAE 30

MANUAL, Owners

KIT, O-Ring Maintenance

KIT, Nozzle Cleaning

25

CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200

_J

>

26

CRAFTSMAN 2200 PSi HIGH PRESSURE WASHER 580.762200

32

33

34

35

13

14

15

16

17

18

19

20

21 item Part # Qty, Description

1

2

3

4

5

6

7

8

9

!0

11 t2

93871

96430A

96542

97675

97570

95524

92479

95531

95435

97671V

97606

93790 t

I

1

1

1

1

4

4

1

1

1

GASKET,EngineAdapter

ADAPTER,Eng_e

BEARING,Eng,Adptr.Ro!ter

Thrust4x4

C - RING,Cam Retainer

WASHER,Thrust

WASHER,Ret_ner

LOCKWASHER,M8 Ribbed

BOLT,SHC5/16- 24 x 3/4"Lg

ADAPTER,EngineShaft3/4"

CAM,Axial6.0 U_

BEARING,Axial CamRoller

Thrust5.5x 4

"O_RING,Crankcase

23

28

29

30

31

24

25

26

27

97568A I

96400 3

99427

94944

3

3

99735

93680

1

3

93668

93667

93652

95416

93876

1

1

3

3

1

A1320

93873

40945

A2069

A2062

A2060

97931

97934

1

6

6

1

3

6

3

6

CRANKCASE,Pump

SPRING,PistonReturn

ASSEMBLY,CeramicPiston& Cap

SHOE,PistonPivot

ASSEMBLY,Bre_lher

SEAL,Oil P_on

SPACER,P_!ot

SEAL,U- Cup ELF

SPRING,ThermalRer_fActuator

PISTON,_ RetiefAc_._,tor

=(7'RING,Them_ Relief

2.gx6.5x 1.78

SPACER,InletPlate

LOCKWASHER,M6 Ribbed

SCREW,SHC M6x 1.0x 20 mm Lg

GASKET,Head

SEAT,CheckValveInlet

POPPET,CheckValve

CAGE,CheckVa_ Inlet

"O"RING,Chk Valve1Z4 x 15.96x

1.78

97929

97843

A2017

A17t9

6

1

2

1

=O"RING,9.25x 12.81x 1.78

PAR-BACK,BackupRing

PIN,2.0Dia.Spindle

66

67

68

69

62

63

64

65

73

74

48

49

58

59

60

61

54

55

56

57

50

51

52

53

A2015

A2503

A2756

89138

2112 3

A1714

B2236

132241

B2665

95441

A2217

A1318

B1758

96053

96015

A1717

B1757

A1718

93644

95380

95379

A1575

97855

A17!3

39

40

41

42

43

44

45

46

47 item Part #

36

37

38

A1711

93656

A3829

A 1712

A 1716

A2016

A2039

A2013

97840

97841

20002

A3805

Qty.

Description

3

3

1 t

1

6

1

1

1

1

1

1

1

1

1

1

1

1

1

1

3

1

1

3

3

1

4

I

1

1

6

3

1

1

1

1

SPINDLE,PressureRegulator

"O"RING,Spind_114x 3/8x 1/16cs

"O"RING,RetainerNut 14 x 17.56x

1.78

_,q', Retainer-S#nd_

SPRING,Unloader

PAR-BACK,BackupRing

HANDLE,Unloader

BOLT,HeadM8 x 125 x 70ramLg

=O"RING,ChkValvecap15.6x 19.16x

1.78

CAP,OutletPort

CAGE,CheckValve

=O"RING, Venturi 10.82 x 14.38 ×

1.78

SEAT,CheckValveOultet

CYLINDER,Head

PLUG, Bulton M8 x 1.25 x 8 mm

SEAL,HighPressure

RING,Bearing

MAGNET,BaitDeflector

_ ButtonM6x l_)x8mm

SET SCREW, M8 - 1.25 x 8 mm

ACTUATOR,Themla!Relief

SPRING,Chemica!Injector

BALL 5.5dia.Chernk_lInjector

BARBHOSE,BrasswithNylonInsert

"O" RING,BaitSeat6.5x t0.5 x 2 cs

SEAT,Ball Unloader

BALL, Stainless Steel 9/32 I_ia.

SEAT, Trapped Line Pressure

VALVE, ShuttlePiston

SPRING, Check Valve

"O" RING, 3.68 x 7.24 x 1.78 cs

VENTURI, Chemical

LOCKNUT, M6 x 1.0 Nylon

CAP, Plastic

WASHER

PILOT, Engine

2?

For the repair or replacement parts you need delivered directly to your home

Call 7 a.m. - 7 p.m., 7 days a week

1-800-366-PART

(t-800-366-7278)

For in-home major brand repair service

Call 24 hours a day, 7 days a week

1-800-4-REPAIR

(1-800=473-7247)

For the location of a Sears Parts and

Repair Center

in your area ........

Call 24 hours a day, 7 daysa week

1 =800-488=1222

For information on purchasing a Sears

Maintenance Agreement or to inquire about an existing agreement

Call 9 a.m. - 5 p.m., Monday-Saturday

1-800=827-6655

The model number of your product is on a decal attached to the pressure washer.

The model number of the engine is located on the blower housing of the engine.

When requesting service or ordering parts,

always provide the following information:

, Product Type

• Model Number

Part Number

. Part Description

America's Repair Specialists

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement