Samsung SDZ-3750T User`s manual

Samsung SDZ-3750T User`s manual

SPD-3750T/3750/3350

37X/33X High Resolution WDR PTZ Dome Camera

37x/33x Ultra-Low Light & WDR SPEED DOME CAMERA

SDZ-3750T/3750/3350

User’s Manual

Before installing and operating the camera, please read this user’s manual carefully.

English

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION -

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING

- CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE

MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE

THE EQUIPMENT.

- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION :

To prevent electric shock and risk of fire hazards:

- The installation for this apparatus should be by a qualified service person and should conform to all local codes.

- Do NOT use power sources other than Class 2 power source.

- Carefully push the unlock buttons to prevent injury due to falling of this apparatus.

This installation should be made by a qualified service person and should conform to all local codes.

Contents

Features

………………………………………………………………………… 6

Cautions for Using Auto Track (SPD-3750T)

………………………… 7

Warnings & Cautions

……………………………………………………… 9

Components and Accessories

…………………………………………… 12

Component Names and Functions

……………………………………… 13

Installing Your Camera

……………………………………………………… 15

Speed Dome Camara and Appliances Wiring Diagram

……… 15

Communication DIP Switch Settings (SW2)

……………………… 17

Protocol Settings

…………………………………………………………………… 17

Baud Rate Settings

………………………………………………………………… 18

Communication Method Settings

……………………………………………… 18

Communication Response Settings

…………………………………………… 18

Termination Settings

……………………………………………………………… 18

Camera Backup Settings

………………………………………………………… 19

Camera ID DIP Switch Settings (SW1)

…………………………… 19

Camera ID Chart

…………………………………………………………………… 20

On-Ceiling Mount Type Installation Example

…………………… 29

Interface Symbols

…………………………………………………………… 32

Operating Your Camera

…………………………………………………… 33

Functional Description

……………………………………………………… 37

Camera Setting

…………………………………………………………… 37

Focus and Zoom

…………………………………………………………………… 37

White Balance

……………………………………………………………………… 39

Exposure

……………………………………………………………………………… 40

Backlight

……………………………………………………………………………… 41

AGC

…………………………………………………………………………………… 45

SSNR(Samsung Super Noise Reduction)

…………………………………… 46

Day & Night

………………………………………………………………………… 47

Others

………………………………………………………………………………… 48

SPEED DOME CAMERA

4

User’s Manual

Sequence Setting

………………………………………………………… 49

Power On Resume & MD Dwell Time

………………………………………… 49

Preset

………………………………………………………………………………… 50

Swing SEQ

…………………………………………………………………………… 54

Group SEQ

…………………………………………………………………………… 55

Tour SEQ

……………………………………………………………………………… 56

PTZ Trace

…………………………………………………………………………… 57

Auto Run

……………………………………………………………………………… 58

P/T Setting

………………………………………………………………… 59

Pan/Tilt Limit

………………………………………………………………………… 59

Area Setting

………………………………………………………………………… 60

Area Masking

……………………………………………………………………… 61

Prop. P/T

……………………………………………………………………………… 62

Digital Flip

…………………………………………………………………………… 63

Image Hold

…………………………………………………………………………… 64

Auto Track1

………………………………………………………………………… 65

Auto Track2

………………………………………………………………………… 67

OSD Setting

…………………………………………………………………… 69

Alarm Setting

………………………………………………………………… 70

Initialization Setting

………………………………………………………… 74

Status Check

…………………………………………………………………… 76

Product Specifications

……………………………………………………… 77

SPEED DOME CAMERA

5

User’s Manual

Features

A/F 37x/33x Optical Zoom

The built-in 37x(SPD-3750T/3750)/33x(SPD-3350) optical zoom lens with auto-focus is combined with a 12x digital zoom, providing a maximum of 444x/396x zoom.

Versatile Protocol Processing

This camera supports a total of 8 types of communication protocols: Samsung Techwin, Pelco-D,Pelco-P, Samsung

Electronics, Panasonic, AD and Vicon.

Wide Range Auto Security

Functions

- Auto Tracking(SPD-3750T Only) : A moving object or a person can be tracked and recorded automatically by the camera with its Pan, Tilt, and Zoom functions.

- Multiple Preset Function Saving : Up to 13 camera image properities can be saved individually to provide high quality pictures.

- Image Holding : When moving between presets in Group and Tour functions, using this Preset Freeze function holds the image status and helps the screen observer relieve visual fatigue.

- PIZ Trace : Patterns operated with the joystick can be saved and replayed by users.

- Swing : Using the Swing function commands the camera to move between 2 selected locations, monitoring the route.

- Group Search : Maximum 255 Preset positions are toured in order.

- Tour Search : Maximum 6 Group Search functions are toured in order.

Digital Flip

The Digital Flip function is useful to monitor moving objects or people passing directly under the camera.

When an object or a person passes directly under the camera, its tilt monitor follows the object or person over

100 degrees to the other side of the tilt area without panning. The screen inversion starting to occur at 100 degrees or higher is digitally adjusted.

Smart P/T

The Smart P/T function automatically adjusts the control speed of the Pan and Tilt functions according to the current zoom power. It is useful to adjust the functions manually for detailed controls when monitoring a high-powered zoom.

Day & Night

With its daytime & nighttime switch and Sens-Up functions based on the ICR (Infrared Cut filter Removal) method, the camera provides high quality pictures regardless of whether it is day or night.

* Sens-Up increases the CCD sensitivity by electrically extending the camera’s exposure time.

* Day & Night enables you to select between color and

B/W modes depending on the lighting conditions.

OSD (On Screen Display)

The camera IDs, camera preset numbers, preset names, area names, and camera operation status are displayed on the monitor, allowing set up of various camera functions through the OSD menu screen.

Preset Position Saving and Loading

Up to 255 preset positions can be set. Using this function saves and brings up the camera feed of a selected monitoring location.

Camera Backup

This is to back up the camera’s sequence information and presets. This is useful when the camera or its install base are damaged or malfunctions occur.

Area Masking

If a monitoring location includes a highly private area, the area can be selectively masked on the screen.

SPEED DOME CAMERA

6

User’s Manual

Cautions for Using Auto Track (SPD-3750T)

The following cautions are for the Auto Track function built-in with the SPD-3750T; The SPD-

3350 do not have Auto Track.

To use Auto Track to its full potential, please read and be aware of the following cautions.

Neglecting the cautions may cause unsatisfactory performance of the tracking function as well as camera malfunctions.

• Auto Track is specifically to track down unknown intruders. It is not be suitable to monitor a crowd.

• If the camera is not safely secured, tracking errors may occur.

• If the camera lens is smeared with foreign substances, snow flakes, or raindrops, the camera may incur unsatisfactory performance in the tracking function. For optimal performance, please install the camera in an environment safe from contamination, and clean the camera lens on regular basis.

• If the tracking function shows poor performance at nighttime or under low light circumstances, use the Sens-Up function.

• Auto Track may have errors at times when pronounced shadows are created: e.g. sunrise and sunset.

• The camera may catch and follow unintended movements – car traffic or swaying tree branches – during the Auto Track operation. To prevent and correct such errors, adjust the installation direction and angle of the camera, or use Zone Settings (Mask) (page 67).

• Adjust the installation direction and angle of the camera, or use Zone Settings also under the following conditions: With excessively bright light sources, under flickering lights, or if the camera displays internal reflections.

• When using Auto Track, it is recommended to adjust the tracking object size to 1/4 of the screen.

• This feature may not perform as expected depending on the situation and circumstances.

Samsung Techwin is not responsible for injuries and financial damage caused by the situation described above.

SPEED DOME CAMERA

7

User’s Manual

Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products. The Eco mark represents

Samsung Techwin's will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive.

Warnings & Cautions

This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly.

* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense.

* Unplug the power plug when thunder crashes or lightning flashes to prevent fire and damage to the product.

* This product is support equipment for a security system. Therefore, we can't compensate for material losses and/or personal injuries by robbery, fire, natural disaster, or anything of the sort.

Warning/Caution/Special Mark Messages

Ignoring this information may result in material loss and/or serious personal injuries, including death.

Ignoring this information may result in material loss and/or slight injuries.

Indicates “Prohibited”.

Indicates “No Disassembly”.

Warnings & Cautions

Warning

Do not install on your own.

Stop using the camera if smoke or abnormal heat is detected.

This installation should be made by a qualified service person. Installing this product on your own may result in fire or electric shock. For the installation service, contact the retail shop where you bought the product.

Do not install in high humidity or in a place that may be exposed to oil or gas.

May cause fire.

Do not install on an unsubstantial wall that may be subject to vibrations.

May cause product malfunctions, electric shocks, and fire.

Do not handle the power plug with wet hands.

May cause the product to fall.

Do not disassemble the camera or insert foreign subjects.

SPEED DOME CAMERA

8

User’s Manual

May cause electric shock.

May cause fire and damage to the product.

SPEED DOME CAMERA

9

User’s Manual

Warnings & Cautions

Cautions

Do not install under extreme temperature conditions.

Do not install under unstable lighting conditions.

Use only under temperature conditions between -0ºC and +50ºC to prevent low graphics quality and product malfunctions. When using in high temperature conditions, provide good ventilation.

Do not drop the camera or subject it to physical shock.

Severe lighting changes or flickering may hinder normal camera operation.

Never keep the camera face to direct sunlight or any other strong lights.

May cause product malfunctions.

Avoid touching the camera lens.

May cause critical damage to the CCD.

Do not install in a place that may be exposed to rain, water, or radioactivity.

The lens is the most important component of the camera.

Be careful not to smear it with fingerprints.

Water leakage into the camera may cause damage.

SPEED DOME CAMERA

10

User’s Manual

Warnings & Cautions

Detailed Warnings and Cautions

- Avoid operating the camera for long durations under high temperatures and in high humidity. Excessive heat can shorten the lifespan of the camera components.

- Do not install or place the camera near any heat sources.

- Subjecting the dome cover to physical shock may damage the camera and cause water leakage into it.

- Do not place the camera facing direct sunlight or other intense light sources. Strong lights such as spotlights can cause distortions—blooming and smear—as well as discolorations on the screen by heating up the color filter of the camera. They also may cause internal reflections of the camera, leading to operational malfunctions.

- Do not drop the camera or subject it to physical shock or vibration; this can cause serious damage to the camera.

- When installing the camera near a power line, make sure to keep at least 1 meter distance from the power line, or earth an additional metal pipe to separate the camera from the power source.

- This camera is to install on the ceiling. Installing it on the ground or a unleveled location may cause product malfunctions and shorten its lifespan.

- This camera is provided with separate indoor and outdoor housings. When installing it in an outdoor environment, use the outdoor housing.

- Avoid installing and operating the camera in the following places.

∙ Places whose temperature exceed the camera’s recommended range. (Indoor: -10

~

50

, Outdoor: Refer to the housing manual)

∙ Places where drastic temperature changes occur: e.g. Near an air conditioner.

∙ Places that are exposed to steam, oil, and inflammable substances: e.g. Inside a kitchen.

∙ Places that are exposed to radioactivity, X-rays, strong electric waves, and electromagnetic waves.

∙ Places that are exposed to outdoor air contaminants: e.g. Dust and car exhaust.

∙ Places in high humidity.

∙ Places that are exposed to corrosive gas: e.g. Next to the sea.

- Smeared and dusty dome covers decrease the picture and video quality. Clean the dome cover and camera lens on a regular basis.

- Remove the plastic wrap on the dome cover only after the camera installation is complete.

- This camera is not equipped with a power switch. Plug in the camera only after the installation is complete.

SPEED DOME CAMERA

11

User’s Manual

Components and Accessories

* Components

Power Adapter (AC 24V, Peak 2.5V)

User’s Manual

* Accessories

The following items are sold separately from the camera.

Housings

STH-380PO

Ultra Low-

Temperature

Heavy

(-40

~50

)

STH-360PO

Low-

Temperature

Lightweight

(-20

~50

)

STH-370PO

Low-

Temperature

Heavyweight

(-20

~50

)

STH-370PEV

Flush-Mount

Indoor Housing

Brackets

STB-350PPM

Parapet Mount

STB-340PCM

Corner Mount

STH-370PI

Indoor Housing

(-10

~50

)

STB-330PPM

Pole Mount

STB-25PF

Indoor Flange

STB-496PPV

Ceiling Bracket

STB-30PF

Indoor Flange

STB-270PWV

Wall Bracket

STB-370PC

Surface-mount

Install Base

STB-270B

Setup Box

SPEED DOME CAMERA

12

User’s Manual

Component Names and Functions

Front

Unlock

Button

Side

Bottom

SW2: Communication DIP Switch

SW1: ID DIP Switch

Safety Wire

Holder

Notes

•FortheDIPswitchsettings,pleaserefertothe“InstallingYourCamera”onPage17.

SPEED DOME CAMERA

13

User’s Manual

Component Names and Functions

Camera Wiring Interface Board (Sold Separately)

For the camera wiring, please refer to the picture below.

The camera’s wiring interface board is equipped to a housing that is sold separately.

Video Output

Alarm

Alarm Output

Fan Heater

Connector

Alarm Input

Communications and AUX

Refer to the below Control

Signal Connection chart

Control Signal Connection

· RS485 Communications

Camera

D+

D-

Controller or DVR

TXD+

TXD-

· RS422 Communications

Camera

D+

D-

TXD+

TXD-

Controller or DVR

TXD+

TXD-

RXD+

RXD-

Power Supply

AC24V 2.5A

Power Input

Ground

AUX Output

Notes

•Themaximumpowercapacityofthebuilt-in relay is 30VDC/2A, 125VAC/0.5A, and

250VAC/0.25A.

•ConnectingthepowerconnectorandGND incorrectly to the NC/NO and COM ports may cause a short circuit and fire, damaging the camera.

SPEED DOME CAMERA

14

User’s Manual

Installing Your Camera

Speed Dome Camara and Appliances Wiring Diagram

Connecting with Samsung Techwin’s “Stand Alone DVR”

· RS-485 :

Camera

D+

D-

Stand Alone DVR

T(TX)+

T(TX)-

SVR-1680/1660/1645/960/

· RS-422 :

Camera

D+

D-

TXD+

TXD-

Stand Alone DVR

T(TX)+

T(TX)-

R(RX)+

R(TX)-

SVR-945

SVR-1650/1640A/950E

Connecting with the Samsung Techwin Controller SCC-3100A

· RS-485 :

Camera

D+

D-

· RS-422 :

Camera

D+

D-

TXD+

TXD-

SCC-3100A

Data Box PORT1

TX+

TX-

RX+

RX-

SCC-3100A

Data Box PORT1

TX+

TX-

RX+

RX-

SVR-940/450

SPEED DOME CAMERA

15

User’s Manual

Installing Your Camera

Note!

* The following DVR models support all functions of the camera.

- 16Ch : SVR-1680/1660/1645/1650E/1640A

- 9Ch : SVR-960/945/950E

- 4Ch : SVR-440

* The following DVR models support only the Pan, Tilt, Zoom, and Focus functions of the camera.

- 9Ch : SVR-940

- 4Ch : SVR-450

* Memo

MEMO

SPEED DOME CAMERA

16

User’s Manual

Installing Your Camera

Communication Protocol DIP Switch Settings (SW2)

SW2 Pin No.

1~4

5~6

7

8

9

10~11

12

Purpose

Protocol Settings

Baud Rate Settings

Transfer Method (RS-485/422) Settings

Response Mode Settings

Backup Mode Settings 1

Termination Settings

Backup Mode Settings 2

Protocol Settings

Select a communication protocol for the camera

10

11

12

13

7

8

9

14

15

16

5

6

3

4

No

1

2

Protocol

Samsung

Pelco-D

Pelco-P

Samsung Elec.

Panasonic

Vicon

Honeywell

AD

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

OFF

OFF

ON

ON

ON

ON

ON

SW2-#1

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

SW2-#2

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

SPEED DOME CAMERA

17

User’s Manual

ON

ON

OFF

OFF

ON

ON

OFF

SW2-#3

OFF

OFF

ON

ON

OFF

OFF

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

SW2-#4

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

Installing Your Camera

• Baud Rate Settings

Select the transfer speed of a selected communication protocol.

No.

1

2

3

4

Baud Rate(BPS)

2,400

4,800

9,600

19,200

SW2-#5

ON

ON

OFF

OFF

SW2-#6

ON

OFF

OFF

ON

Communication Method Settings

Select a communication method for the camera.

SW2- #7

Function

Transfer Mode Switch

ON

RS-422(4Wire)

OFF

RS-485(2Wire)

Communication Response Settings

Select a communication response method for the camera and controller: Response or No

Response.

SW2- #8

Function

Response Mode Switch

ON

Response

OFF

No Response

Termination Settings

To prevent the attenuation of communication signals between the camera and controller, 2 cameras in a longest distance for the camera and controller communication loop must be set up with the termination settings.

Camera Input Position

Longest Distance Terminal

In the Middle of Loop

SW2- #10

ON

OFF

SW2- #11

ON

OFF

OFF

ON

OFF

SPEED DOME CAMERA

18

User’s Manual

Installing Your Camera

Camera Backup Settings

These settings are useful when the camera or its install base are damaged or malfunctions occur. When replacing the camera or its install base, you can transfer existing presets and sequence information to the replacement using these settings.

Backup Function

Backup(IB → D)

Backup(D → IB)

Backup Disable

SW2- #9

OFF

ON

-

SW2- #12

OFF

OFF

ON

- Backup(IB

D): Enables transferring the current camera’s sequence information to a new install base.

- Backup(D

IB): Enables transferring the current camera’s sequence information to a new camera.

Notes

•Touseathirdpartycontrollerwiththisproduct,pleasecontactourAfter-SalesServiceor

Technology Department.

•ADProtocolControlMethod

- Input Camera OSD: 3+Auxiliary On

- Output Camera OSD: 3+Auxiliary Off

- Enter: IRIS Open

- ESC: IRIS Close

•Formoreinformationabouttheprotocols,refertoourofficialwebsite.

Camera ID DIP Switch Settings (SW1)

To set up camera IDs, refer to the “Camera ID Chart” below.

SPEED DOME CAMERA

19

User’s Manual

Installing Your Camera

• Camera ID Chart

34

35

36

37

30

31

32

33

38

39

40

41

21

22

23

24

17

18

19

20

25

26

27

28

29

8

9

10

11

6

7

4

5

12

13

14

15

16

ID

1

2

3

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

SW1-#1

ON/OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

SW1-#2

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

SW1-#3

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#5

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

SW1-#4

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#7

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#6

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#8

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SPEED DOME CAMERA

20

User’s Manual

Installing Your Camera

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

SW1-#1

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

65

66

67

68

61

62

63

64

69

70

55

56

57

58

51

52

53

54

59

60

ID

46

47

48

49

50

42

43

44

45

75

76

77

78

71

72

73

74

79

80

81

82

83

84

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

SW1-#3

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

SW1-#2

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#5

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

SW1-#4

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#7

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#6

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#8

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SPEED DOME CAMERA

21

User’s Manual

Installing Your Camera

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

SW1-#1

ON

OFF

ON

OFF

ON

OFF

115

116

117

118

111

112

113

114

119

120

101

102

103

104

105

106

107

108

109

110

121

122

123

124

125

126

127

95

96

97

98

91

92

93

94

99

100

ID

85

86

87

88

89

90

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

SW1-#3

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

OFF

ON

ON

OFF

OFF

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

SW1-#2

OFF

ON

ON

OFF

OFF

ON

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

SW1-#5

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#4

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#7

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#6

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#8

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SPEED DOME CAMERA

22

User’s Manual

Installing Your Camera

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

SW1-#1

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

148

149

150

151

152

153

154

155

156

157

138

139

140

141

142

143

144

145

146

147

ID

128

129

130

131

132

133

134

135

136

137

158

159

160

161

162

163

164

165

166

167

168

169

170

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

SW1-#3

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

SW1-#2

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

SW1-#5

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

SW1-#4

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#6

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#8

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#7

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

SPEED DOME CAMERA

23

User’s Manual

Installing Your Camera

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

SW1-#1

ON

OFF

ON

OFF

ON

OFF

197

198

199

200

201

202

203

204

205

206

187

188

189

190

191

192

193

194

195

196

207

208

209

210

211

212

213

177

178

179

180

181

182

183

184

185

186

ID

171

172

173

174

175

176

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

SW1-#3

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFF

ON

ON

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

SW1-#2

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#5

OFF

OFF

OFF

OFF

OFF

ON

OFF

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

SW1-#4

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#7

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#6

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#8

ON

ON

ON

ON

ON

ON

SPEED DOME CAMERA

24

User’s Manual

Installing Your Camera

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

ON

OFF

ON

OFF

ON

OFF

ON

SW1-#1

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

230

231

232

233

234

235

236

237

238

239

223

224

225

226

227

228

229

ID

214

215

216

217

218

219

220

221

222

250

251

252

253

254

255

240

241

242

243

244

245

246

247

248

249

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

SW1-#3

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

SW1-#2

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#5

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

SW1-#4

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#7

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

OFF

ON

ON

ON

ON

ON

ON

SW1-#6

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SW1-#8

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

SPEED DOME CAMERA

25

User’s Manual

Installing Your Camera

Preparing Adapter and Cables

– Power Adapter

Power adapter has the capacity of AC24V 2.5A.

– Video Cable

A BNC coaxial cable shown in the picture is required to connect Speed Dome’s video output terminal to the monitor.

Distance

500m or shorter

500m or longer

Recommended Cable Specification

5C2V Coaxial Cable

7C2V Coaxial Cable

– Communications Cable

For the camera to communicate with the controller, a RS-485/422 communications line is required. To ensure the quality of long distance communications and the accuracy of the overall communications, using a twisted pair cable such as UTP Cable is recommended.

* Caution!

Depending on the camera’s environment, the communications distance may vary.

Notes

•Neitherthevideonorcommunicationscableisenclosedwiththecamera.

SPEED DOME CAMERA

26

User’s Manual

Installing Your Camera

Preparing and Installing Camera Bracket

For the installation guidelines for the brackets and housings, refer to the user’s manual enclosed with the bracket or housing that is sold separately.

• Camera Wiring Diagram 1

SPEED DOME CAMERA

27

User’s Manual

Installing Your Camera

• Camera Wiring Diagram 2

SPEED DOME CAMERA

28

User’s Manual

Installing Your Camera

On-Ceiling Mount Type Installation Example

1. Attaching Template and Installing STB-370PC

Attach the enclosed template to the ceiling, then drill a hole in the ceiling according to the diameter marked on the template. Drop the camera cables down from the ceiling through the hole. Next, install the exposed bracket STB-370PC to the ceiling as shown in the picture.Before installing the exposed bracket, open the hinged door at the bottom of the bracket as shown in the picture. Hold the knob on the hinged door to open.

Template

Knob

2. Wiring Terminal Cables

Connect the cables to the terminal block on the hinged door. For the location of the wiring pins, please refer to the “Camera Wiring Diagram” on Page 14. Once the wiring is successful, close the hinged door.

Notes

•Donotconnectthecameratoapoweroutletuntiltheinstallationiscomplete.Supplying

power in the middle of the installation may cause fire or damage the product.

SPEED DOME CAMERA

29

User’s Manual

Installing Your Camera

3. Setting Up Camera DIP Switches

DIP switches for communication and ID protocols are located on the bottom of the camera. For the switch settings, refer to the dip switch settings of this manual.

ID(SW1)

Protocol(SW2)

5. Connecting Camera Safety Cable and Attaching Camera

Carefully attach the camera to the mount following the alignment guide marks as shown in the picture. First hook the camera's safety cable on the mount, and then attach the camera.

Safety

Cable

Alignment

Direction

Guides

Alignment

Direction

Guides

Alignment

Directions

To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.

Notes

•Makesuretofirsthookthecamera'ssafetycabletothemountbeforeproceeding.

Otherwise you may be exposed to serious injury caused by a fallen camera.

SPEED DOME CAMERA

30

User’s Manual

Installing Your Camera

To attach or detach the camera, refer to the picture.

* Attaching the camera: Hold up the camera and push it to the mount as shown in the picture. Push the camera until you hear a “click”.

* Detaching the camera: To detach the camera, pull the camera downward while pushing the unlock buttons on the camera upward.

Unlock Button

UNLOCK

To attach the camera

To detach the camera

SPEED DOME CAMERA

31

User’s Manual

Interface Symbols

• Motion Detection Standby/Operation Display :

- When in standby mode, the " " in the upper right of the screen blinks and then changes to " " if motion is detected.

• Motion Detection Operation Display :

- The icon in the upper right of the screen blinks.

• Alarm Input Port Status Display :

- "

","

","

", and "

" in the upper right of the screen blink.

• Current Alarm Port Display According to Input Alarm Ports(Priority) :

- Only one of " "," ","

• Preset Number Display Settings :

"," " in the upper right of the screen blinks.

- '*' : If a preset number is already available

- 'H' : If a preset location is the camera’s home position

- 'T' : If a preset location is the camera’s Auto Track starting point (SPD-3750T Only)

• If an OSD Menu has Sub Menus :

- The color of the circle around the menu number shows as embossed, e.g. "

".

• If an OSD Menu Does Not Have Sub Menus :

- The circle around the menu number shows as engraved, e.g. " ".

• PTZ Function Screen :

Motion Detect

Alarm Input

Area Display

ID=001

Area1 Area Name

①②③④

Sequence Status

Preset Info

G-SEQ1

PRESET=001 Preset Name

P:3000 T:040 10X

• Preset Number Setting Screen :

Preset Edit

Preset=011

*

(1~255)

SPEED DOME CAMERA

32

User’s Manual

Operating Your Camera

• OSD Menu Screen :

Sub Menu Available

Sub Menu Not Available

Camera Setting

Focus & Zoom

White Balance

---

---

ATW

Operating Your Camera

• Panning and Tilting

- Use the joystick of the controller or its direction buttons.

• Controlling Zoon

- Move the joystick clockwise (Tele) or counterclockwise (Wide), or use the Zoom button.

• Accessing Screen Menus

- Press the Menu or OSD button on the controller.

For more detailed information about controls using a third party controller or a DVR, refer to the user’s manual of the product.

OSD Commands, Function Chart, and Menu Controls

This dome camera can be operated using two methods: Using hot keys on its dedicated controller, or accessing the OSD (On Screen Display) on the video output. The OSD menu commands are as follows:

Command

Move the joystick up/down/left/right

Enter/Focus Far

ESC/Focus Near

Function

Moves the OSD menus up/down/left/right, respectively.

Selects a menu and allows access to the sub menus.

Cancels a command and moves back to an upper-level menu.

Dome Cover Setting

Before optimizing the camera focus settings for the dome cover shape, please select the dome cover type on the camera’s main menu. (Refer to Page 48)

Dome Cover Setting

Outer

Inner

None

Installation Type

Dome cover type for outdoor housings except the indoor flush model.

Default dome cover type including the indoor flush model.

When using the camera without a dome cover.

SPEED DOME CAMERA

33

User’s Manual

Operating Your Camera

*OSD Menu Chart

P1 P2

① Focus

&Zoom

② White

Balance

③Exposure

① Camera

Setting

④ Back Light

⑤AGC

⑥SSNR

⑦ Day

&Night

⑧Others

①Preset

P3

①Focus Mode

②Zoom Tracking

③Digital Zoom

AWB Mode

P4 P5

Auto/Manual/One Shot AF

Mode Auto/Tracking/Off

Default

One Shot AF

Auto

Speed Slow/Medium/Fast Fast

Off/2X/3X/4X/5X/.../12X Off

ATW/INDOOR/OUTDOOR/AWC

Manual

Red

Blue

ATW

117

93

①Brightness

②Iris

③Shutter

④Sens-Up

①Off

0~100

Auto

Manual Iris Level

---/A.FLK/Manual

Auto/Off

Sens-Up Limit

X2/X4...X256

Limit

50

Auto

F1.6

---

Auto(X2)

Off

Low/Medium/High Medium

②WDR

③HLC

Manual

Level

Level

Mask Color

Level

Off/Low/Medium/High

Auto

1~100

Low/High

0~10

④ User

Up/Down/Left/Right/

Increase/Decrease

Off/Low/Medium/High

5~41

50

Low

5

Medium

5dB

Medium

Mode

Duration

Dwell Time

Sync

Stabilizer

Color

B/W

Burst Level

0~100

Burst On/Off

Slow/Fast

5/7/10/15/20/30/40/60 sec

Internal

Line Lock

On/Off

Line Lock Phase

Color

Fast

5sec

Internal

Image Adj.

Freeze

①Sharpness On(0~32)/Off

②Color 0~100

On/Off 

Dome Cover Inner/Outer/None

①Setting②Edit③Home Position④Execute⑤Clear

⑥Status

Off

24

50

Off

Inner

SPEED DOME CAMERA

34

User’s Manual

Operating Your Camera

Sequence

Setting

③ P/T

Setting

②Swing SEQ.

①Pan Swing

②Tilt Swing

③P&T Swing

③Group SEQ. Group1~6

①Pan Limit

①Setting②Execute③Clear

①Setting②Execute③Clear

①Setting②Execute③Clear

①Setting②Execute③Clear

④Tour SEQ.

①Setting②Execute③Clear

⑤PTZ Trace Trace1~4 ①Replay②Memorize

⑥Auto Run

①Mode

②Time

Off/Home/Preset/Swing/Group/

Tour/Trace/A.Pan

1~60(Sec), 1~60(Min)

⑦ Power On

Resume

⑧ MD Dwell

Time

On/Off

①Off

②On 1~60(Sec),1~60(Min)

①Position

① Pan/Tilt

Limit

②Tilt Limit

②On/Off

①Position

②On/Off

①Name/②Position/③On/Off ②Area Setting Area1~8

③ Area

Masking

Mask1~8

④Prop.P/T On/Off

⑤Digital Flip On/Off

①Position/②On/Off

⑥Image Hold On/Off

①Auto Track On/Off

②Camera Height 2.5m~30m

⑦Auto Track 1

③Object Size

④Sensitivity

⑤Zoom Control

⑥Auto Release

⑦Auto Return

⑧Lost Mode

Small/Medium/Large

High/Medium/Low

Off/One Shot/Continuous

Off/10sec~5min

Off/1sec~5min

Stop/Research/Zoom Out

⑧Auto Track 2

①Zone Setting Zone1~8

①Position

② Mode(Alarm/

Mask)

②Indicator

③Target Lock

①Camera ID On/Off

③On/Off

Off/On/Pointer/Target

On/Off

Off

30

On

Mask

Off

Off

Off

On

30 Sec

Off

On

On

Off

Off

Off

Off

Off

2.5m

Small

High

Off

Off

Off

Stop

SPEED DOME CAMERA

35

User’s Manual

Operating Your Camera

④ OSD

Setting

⑤ Alarm

Setting

⑥Initialize

② Camera

Name

③ Preset

Number

④ Preset

Name

① Alarm

Enable

①On/Off

②Edit

On/Off

①On/Off

②Edit

⑤ Sequence

Status

On/Off

⑥Area Name On/Off

⑦ PTZ

Position

On/Off

⑧Language English/Chinese/Fran

ç ais/Deutsch/Espa

ñ ol/Italiano

On/Off

②Alarm Input

③ Alarm

Output

⑤Aux. Output

①In1

②In2

③In3

④In4

Out1~2

Time1~2

①On/Off

②Time

MOD:NC/NO/OFF

Priority:1~4 

SEQ:Preset/Swing/Group/Tour/

A.Pan/Trace/Off

1~4,MD,TRK

Off/On/Momentary

Dwell Time

1~60(Sec),

1~60(Min)

On/Off

1~60(Sec), 1~60(Min)

① Power On

Reset

② Factory

Default Set

③ Camera

Default Set

④ Auto

Refresh

⑤ Auto Track

Default

⑥ Data

Transfer

Cancel/Execute

Cancel/Execute

Cancel/Execute

Off,1~7Days

Cancel/Execute

Copy To Install Base/Copy To Dome

⑦Status

Off

On

Off

On

Off

On

English

Off

Off

Off

Off

Off

SPEED DOME CAMERA

36

User’s Manual

Functional Description

Camera Setting

1. Focus and Zoom Settings

1.1 Focus Mode and Digital Zoom Setting Menu

Main Menu/Camera Setting/Focus & Zoom

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

Medium

Medium

Focus & Zoom

Focus Mode

② Zoom Tracking

ONE SHOT AF

③ Digital Zoom OFF

Focus Mode :

- Auto : Performs continuous auto-focus.

- Manual : Changes the camera mode to Manual Focus.

- One Shot AF : Auto-focuses the camera once after the

Pan, Tilt, or Zoom function is used.

Digital Zoom :

Enables the maximum digital zoom.

Setting the digital zoom to 12X provides a total zoom of

444x(SPD-3750T/3750)/396x(SPD-3350).

Notes

•Unliketheopticalzoom,thegraphicsqualityofthe digital zoom decreases as its zoom power increases.

•Theauto-focusfunctionmaynotoperatenormally under the following conditions :

- When background illumination is low

- While Slow-Shutter is in operation

- If the zoom level is set too high

- When background illumination is too high

- If a long distance object and a close distance object appear together within a monitoring area

- If there is no contrast, e.g. the sky or a wall

- If the camera is facing a thin horizontal line

•AutoFocusfocusesonanobjectinthecenterofthe screen; objects around the screen edges may not be properly in focus.

SPEED DOME CAMERA

37

User’s Manual

Functional Description

1.2 Zoom Tracking

Main Menu/Camera Setting/Focus & Zoom/Zoom Tracking

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

Medium

Medium

Focus & Zoom

Focus Mode

② Zoom Tracking

ONE SHOT AF

③ Digital Zoom OFF

Zoom Tracking

Mode

② Speed

AUTO

FAST

Through this menu you can set up the camera’s focus mode when zooming.

Mode :

- Auto : Auto-focuses when zooming.

- Tracking : Focuses manually when zooming.

- Off : Disable the focus modes when zooming. (Full manual mode)

Speed :

- Slow/Fast : Adjusts the zooming speed.

SPEED DOME CAMERA

38

User’s Manual

Functional Description

2. White Balance

Main Menu/Camera Setting/White Balance

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

OFF

Medium

Medium

The White Balance menu adjusts the balance of the screen colors under different lighting conditions.

- ATW : Adjusts the screen color automatically.

- Indoor : Adjusts the screen color to be optimal in an indoor environment.

- Outdoor : Adjusts the screen color to be optimal in an outdoor environment.

- AWC : Adjusts the screen color to be optimized to the current lighting and monitor conditions. Using this setting may require an readjustment if the lighting conditions changes.

- MANUAL : Enables customization the Red and Blue gains.

Notes

White Balance may not work properly under the following conditions.

When the color temperature of the environment surrounding the subject is out of the control range.(e.g. Clear sky or sunset)

When the ambient illumination of the subject is dim.

If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, White Balance adjustments may not deliver consistent results.

SPEED DOME CAMERA

39

User’s Manual

Functional Description

3. Exposure

Main Menu/Camera Setting/Exposure

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

OFF

Medium

Medium

The Exposure settings are to control the camera’s exposure meter.

Brightness :

Adjusts the screen brightness.

(Over 50: Brighter, Under 50: Darker)

Iris :

- Auto : Automatically adjusts the exposure meter.

- Manual : Enables manual adjustment of the exposure meter. (Over 50: Brighter, Under 50: Darker)

Shutter :

Controls the camera’s electronic shutter.

- --- : The shutter speed is fixed at 1/60 for NTSC and 1/50 for PAL. Operates when Iris is on the Auto Mode.

- ESC : Adjusts the shutter speed automatically according to the screen brightness. Operates when Iris is on the Manual Mode.

- A.FLK : Select this setting when you experience picture flickering. Flickering can happen when artificial lighting frequencies clash with camera frame rates.

- Manual : Enables manual adjustment of the shutter speed.

Sens-Up :

- Auto : Automatically detects light levels and maintains a clear picture at night or under low-light conditions.

- Sens-Up Limit : Adjusts to the maximum-powered zoom per frame.

Exposure

Brightness

Iris

Shutter

Sens-Up

050

AUTO

---

AUTO

Notes

•ForoptimalperformanceoftheA.FLKmode,avoid using the mode in conjunction with Backlight.

•WhiletheInternalSyncmodeisineffect,settingthe shutter to '---' and facing the camera directly to a bright light source may cause poor camera performance.

•Sens-UpisdisabledwhentheshutterisinManualor

A.FLKmode.

SPEED DOME CAMERA

40

User’s Manual

Functional Description

4. Backlight

4.1 Backlight Mode Settings

Main Menu/Camera Setting/Back Light

Main Menu

Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

Others

ATW

OFF

Medium

Medium

Unlike other cameras, Samsung Techwin’s unique W-III DSP chip gives you a clear image of the subject even with bright backlight.

Back Light Mode :

- Off : Disables the Backlight mode.

- WDR : Activates the Wide Dynamic Range mode.

- HLC : Activates the High Light Compensation mode.

- User : Activates a user defined backlight compensation mode.

SPEED DOME CAMERA

41

User’s Manual

Functional Description

4.2 WDR

Main Menu/Camera Setting/Back Light/WDR

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

Initialize

Status

Camera Setting

Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

WDR Setting

Limit

Level

ATW

WDR

Medium

Medium

Medium

50

When there are both bright and dark areas at the same time, this mode makes both areas distinctive.

WDR ON

WDR Off

Limit :

Three WDR sensitivity levels are available in 3: Low,

Medium , and High.

Note that the higher the sensitivity level, the lower the contrast in the light and dark areas becomes.

Level :

Adjusts the screen brightness in WDR mode.

Notes

•WDRisdisablediftheshutterisinManualmode.

•DuringWDRoperation,noise,discoloration,spots,and whitish symptoms may occur depending on lighting conditions. If they occur, stop using WDR.

SPEED DOME CAMERA

42

User’s Manual

Functional Description

4.3 HLC

Main Menu/Camera Setting/Back Light/HLC

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

HLC Setting

Limit

Mask Color

ATW

HLC

Medium

Medium

Medium

05

The HLC settings selectively eliminates high lights in a limited environment such as the entrance to an apartment parking lot or gas station, and is useful to detect a small objects like car license plates.

HLC is disabled during the daytime. While monitoring nighttime car traffic, if car headlamps reflect too bright lights on the screen, the camera automatically eliminates the headlamp lights and adjusts the colors of the license plate accordingly.

HLC Masking Area

<HLC ON> <HLC OFF>

Limit :

Adjusts the HLC sensitivity level.

Mask Color :

Adjusts the mask color on the highlighted area.

Notes

•EvenifHLCison,carlicenseplatesmaynotbedetectabledependingonthelocationand angle of the camera as well as the lighting condition.

SPEED DOME CAMERA

43

User’s Manual

Functional Description

4.4 User Area Setting

Main Menu/Camera Setting/Back Light

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

USER

Medium

Medium

You can selectively choose a screen area to see objects within the area more clearly than others.

Four-direction Joystick Controls :

- Moving the joystick in all four directions—upward, downward, left, and right—adjusts the location and size of a selected area.

Zoom Control :

- Zoom Tele : Enlarges the size of a selected area.

- Zoom Wide : Reduces the size of a selected area.

:Up

:Down

:Left

:Right

W:Decrease T:Increase

SPEED DOME CAMERA

44

User’s Manual

Functional Description

5. AGC

Main Menu/Camera Setting/AGC

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

OFF

Medium

Medium

AGC (Automatic Gain Control) adjusts the camera’s gain control and the screen brightness if the camera has captured an object under low-light conditions.

The Off, Low, Medium, High, and Manual modes are available.

SPEED DOME CAMERA

45

User’s Manual

Functional Description

6. SSNR (Samsung Super Noise Reduction)

Main Menu/Camera Setting/SSNR

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

Initialize

Status

Camera Setting

① Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

OFF

Medium

Medium

SSNR significantly reduces the amount of low luminance noise.

- Off : Disables the noise reduction function.

- Low : Reduces only a small amount of noise, but generates almost no afterimage.

- Medium : The most commonly used mode. Reduces a suitable amount of noise while generating a subtle afterimage.

- High : Reduces noise significantly, but generates obvious afterimages.

Notes

•SSNRisdisabledwhentheAGCmodeisturnedoff.

SPEED DOME CAMERA

46

User’s Manual

Functional Description

7. Day & Night

Main Menu/Camera Setting/Day & Night

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

Alarm Setting

⑥ Initialize

Status

Camera Setting

Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

Day & Night

① Mode

Duration

③ Dwell Time

ATW

OFF

Medium

Medium

COLOR

FAST

0.5 SEC

The Day & Night function allows the camera to switch between the Color and B/W modes.

Modes :

- Auto : Operates in Color mode most times, and switches to B/W mode if a low light level is detected during nighttime.

- Color : Operates in Color mode at all times.

- B/W : Operates in B/W mode at all times. By using the

Burst On/Off sub menu, burst signals can be retained or disabled.

If the camera is in B/W mode and connected to equipment that requires external sync through burst signals, set the

Burst On/Off option to “On.”

Duration :

The camera’s light sensitivity is adjustable as in the chart below. The camera’s ambient light diversion performance may vary depending on its environment.

Fast

Slow

Color -> B/W

2.5 Lux

0.8 Lux

B/W -> Color

4 Lux

6 Lux

Dwell Time :

The duration of both the lighting conditions can be customized to let the camera divert between the daytime and nighttime settings.

Notes

•TheAutomodeisdisabledwhenAGCisturnedoff.Thisfunctionisonlyavailablewhen

the Color or B/W mode is selected.

•UsingB/Wmodeundersunlightorahalogenlampmaydecreasethefocusing performance.

SPEED DOME CAMERA

47

User’s Manual

Functional Description

8. Others

Main Menu/Camera Setting/Others

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

Alarm Setting

⑥ Initialize

Status

Camera Setting

Focus & Zoom

White Balance

③ Exposure

④ Back Light

AGC

SSNR

⑦ Day & Night

⑧ Others

ATW

OFF

Medium

Medium

Others

Sync

Stabilizer

③ Image Adj

Freeze

Dome Cover

INTERNAL

OFF

OFF

Inner

Sync :

Enables selecting Internal Synchronization or the external Line Lock. (SPD-3750T not supported)

- Internal : Synchronizes the camera’s output timing to the internal crystal.

- Line Lock : Synchronizes the camera’s output timing to the AC adapter power to synchronize multiple cameras. This option is useful when using a switch such as Matrix Switcher.

- Line Lock Phase : Enables setting the adapter’s synchronization phase between 0 and

360°.

Stabilizer :

The Stabilizer compensates for any small movements of the camera caused by due to the wind and other reasonsor other causes.

Notes

•TheStabilizerusesthedigitalzoomandmaycause low picture quality.

•TheStabilizerisdisablediftheambientlightistoo low.

•TheStabilizerisdisabledifthefieldofviewhasvery low or no contrast, e.g. The sky or a white wall.

Image Adj :

- Sharpness : Sharpens outlines of an image.

- Color : Adjusts the color density of an image.

Freeze :

Stops or reanimates an image.

Dome Cover :

These settings are to optimize the camera’s focused object position according to the dome cover type.

- Inner : When using the camera without a housing.

(Factory Release Mode)

- Outer : When using the camera with a housing.

- None : When using the camera without the dome cover.

SPEED DOME CAMERA

48

User’s Manual

Functional Description

Sequence Setting

9. Power On Resume and MD Dwell Time

Main Menu/Sequence Setting

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

ON

ON

Power On Resume :

This is useful when the power is disconnected and reconnected due to power failures or other power interruptions.

If the camera was performing a sequence action prior to a power disconnection, the camera automatically resumes the action when the power is reconnected.

MD Dwell Time :

When Motion Detection under the Preset Edit menu is selected, MD Dwell Time performs the Tour or Group function.

While the camera is performing a sequence action, if motion is detected from a selected preset location, the camera pauses the sequence action operation and starts monitoring the location instead for a duration that is set under the MD Dwell Time menu.

If the motion is no longer detectable or the duration expires, the camera aborts the monitoring operation and then resumes the sequence action.

SPEED DOME CAMERA

49

User’s Manual

Functional Description

10. Preset

10.1 Preset Location Saving

Main Menu/Sequence Setting/Preset/Setting

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

Preset

Setting

Edit

Execute

Clear

Status

ON

OFF

This function enables the memorization of a selected location and activates the Pan, Tilt, and Zoom functions at that location.

Saved locations can be recalled using the Preset Execute command.

Setting Up Preset Numbers :

Selecting the Preset Setting menu brings up a screen as shown below. Move the joystick in all four directions to select the desired number.

Preset Setting

Preset = 001 (255)

Saving Preset Locations :

Selecting a preset number and pressing the Enter key redirects the menu to the screen shown below.

Using the joystick, adjust the location of the Pan and Tilt functions and then set the Zoom and Focus command.

In Preset Settings, the Zoom and Focus command is controllable only by the Zoom command. To switch between Zoom and Focus, use the Preset 1 and 2 commands as shown below.

Preset Setting Z>Z00M

1+PST:ZOOM 2+PST:FOCUS

Use W/T Preset

SPEED DOME CAMERA

50

User’s Manual

Functional Description

Main Menu

① Camera Setting

② Sequence Setting

....

Sequence Setting

① Preset

② Swing SEQ

Group SEQ

....

Preset

Setting

Edit

③ Home Position

Execute

Clear

Status

Preset Edit

OFF

Preset = 001* (1~255)

Preset Edit

[001]

PTZ 271/045/1X

Focus Mode ONE SHOT AF

Brightness 050

Iris AUTO

⑤ Back Light

Day & Night B/W

After Act. OFF

⑧ Scene Adj.

10.2 Preset Edit

Main Menu/Sequence Setting/Preset/Edit

You can edit the 13 preset items such as Pan/Tilt location,

Zoom and Focus, which are selected among camera functions.

PTZ :

Recalls saved locations using the Preset Settings command.

Focus Mode :

Refer to the section entitled Setting Up Your Camera.

Brightness :

Refer to the section entitled Setting Up Your Camera.

Iris :

Refer to the section entitled Setting Up Your Camera.

Backlight :

Refer to the section entitled Setting Up Your Camera.

Day & Night :

Refer to the section entitled Setting Up Your Camera.

After Act :

Enables setting up an automatic action after the camera arrives at a selected preset location.

- TRACK : Commands the camera to perform the Auto

Tracking function.

- MD : Commands the camera to perform the Motion

Detection function.

- None : Select this when no action is desired.

Scene Adj :

Enables setting the Shutter, AGC, SSNR, Sens-Up, White

Balance, and Stabilizer functions. For more information about interface terminology, please refer to the section entitled Setting Up Your Camera.

SPEED DOME CAMERA

51

User’s Manual

Functional Description

Main Menu

10.3 Preset Name Setting

Main Menu/OSD Setting/Preset Name/Edit

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

OSD Setting

Using this function, you can add names to preset locations.

up to 12 characters.

Once a name is entered, use the joystick and the Enter key to perform the Set command and save the name.

ON ① Camera ID

② Camera Name

③ Preset Number

④ Preset Name

....

Preset Name

ON/OFF

Edit

Preset Edit

ON

OFF

Preset = 001* (1~255)

PSET Name 001[ ]

0123456789()[]#&%/~-=_

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ

ABC->

中文

1 BACK SPACE CLR SET

SPEED DOME CAMERA

52

User’s Manual

Functional Description

10.4 Preset Execution/Deletion/Memory Check

Main Menu/Sequence Setting/Preset

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

Preset

Setting

Edit

③ Home Position

Execute

Clear

Status

ON

OFF

OFF

Home Position :

Sets one of the currently configured preset positions as the home position.

Execute :

Recalls a saved preset location.

Clear :

Deletes the selected preset location.

Status :

Opens a map of saved preset locations.

An area saved as a preset location is displayed with the

'

' icon.

Preset Status

001 : □□□□□ □□□□□ □□□□□ □□□□□

021 :

□□□□□ □□□□□ □□□□□ □□□□□

041 : □□□□□ □□□□□ □□□□□ □□□□□

061 :

□□□□□ □□□□□ □□□□□ □□□□□

081 : □□□□□ □□□□□ □□□□□ □□□□□

101 :

□□□□□ □□□□□ □□□□□ □□□□□

121 :

141 :

161 :

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

Preset Status

181 :

□□□□□ □□□□□ □□□□□ □□□□□

201 : □□□□□ □□□□□ □□□□□ □□□□□

221 :

241 :

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

□□□□□

SPEED DOME CAMERA

53

User’s Manual

Functional Description

11. Swing SEQ

Main Menu/Sequence Setting/Swing SEQ

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

Auto Run

Power On Resume

MD Dwell Time

Swing SEQ

① Pan Swing

② Tilt Swing

③ P&T Swing

ON

OFF

The Swing function commands the camera to move between 2 selected locations, monitoring the route.

Pan Swing :

Activates the Pan function for the Swing operation.

Tilt Swing :

Activates the Tilt function for the Swing operation.

P&T Swing :

Activates both the Pan and Tilt functions for the Swing operation.

Swing Settings/Execute/Clear :

- Settings : Each of the Swing menus have sub menus with the settings.

Pan Swing

Setting

② Execute

③ Clear

Pan Swing Setting

[001]

←→

[***]

SPEED=64 (1~64)

DWT =003(1~128)(s)

Select 2 preset locations by using the joystick.

Speed indicates the camera’s movement speed. DWT indicates the camera’s duration of stay at a preset location.

- Execute: Executes the Swing operation.

- Clear: Deletes data in the Swing memory.

SPEED DOME CAMERA

54

User’s Manual

Functional Description

12. Group SEQ

Main Menu/Sequence Setting/Group SEQ

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

Group SEQ

① Group 1

② Group 2

③ Group 3

Group 4

....

Group SEQ 1

Setting

Execute

Clear

ON

OFF

Selecting Group SEQ recalls a group of multiple preset locations in a consecutive manner. A group can contain up to

255 preset locations.

Setting :

Using the joystick, enter desired preset numbers into the

PSET section. DWT indicates the camera’s duration of stay at a preset location. SPD shows the camera’s movement speed by 64 different levels.

Group SEQ 1

NO PSET DWT(s) SPD

001: *** : 003 : 64

002: *** : 003 : 64

003: *** : 003 : 64

004: *** : 003 : 64

005: *** : 003 : 64

006: *** : 003 : 64

007: *** : 003 : 64

Execute :

Executes the group operation.

Clear :

Deletes the selected group.

SPEED DOME CAMERA

55

User’s Manual

Functional Description

13. Tour SEQ

Main Menu/Sequence Setting/Tour SEQ

Main Menu

① Camera Setting

Sequence Setting

P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

Tour SEQ

Setting

Execute

Clear

ON

OFF

Selecting Tour SEQ recalls groups of preset locations in a consecutive manner. Up to 6 groups can be listed for this function.

Settings :

Selecting the Settings menu brings up the following screen.

Using the joystick, you can enter desired group numbers to the Group section. DWT indicates the camera’s standby time before a new group is recalled.

Tour SEQ

NO Group DWT(s)

01: * 003

02: * 003

03: * 003

04: * 003

05: * 003

06: * 003

Execute :

Executes the group operation.

Clear :

Deletes the selected group.

SPEED DOME CAMERA

56

User’s Manual

Functional Description

14. PTZ Trace

Main Menu/Sequence Setting/PTZ Trace

Main Menu

① Camera Setting

② Sequence Setting

P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

PTZ Trace

① Trace 1

② Trace 2

③ Trace 3

④ Trace 4

PTZ Trace 1

Replay

Memorize

ON

OFF

Maximum 4 patterns of the manual operation paths (for Pan,

Tilt, Zoom and Focus) are memorized and replayed.

Replay :

Replays a route saved by the Trace function. Use the Stop button to stop the replay.

Memorize :

Up to 120 seconds of a memory can be saved. The memory duration varies depending on the difficulty level of the PTZ

Trace action. If the memory capacity is full, the Over message appears and the memorization action is terminated.

SPEED DOME CAMERA

57

User’s Manual

Functional Description

15. Auto Run

Main Menu/Sequence Setting/Auto Run

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Sequence Setting

① Preset

② Swing SEQ

③ Group SEQ

④ Tour SEQ

⑤ PTZ Trace

⑥ Auto Run

Power On Resume

MD Dwell Time

Auto Run

Mode

Time

ON

OFF

OFF

30 SEC

If there is no controller operation by the user for a certain time, the sequence operation designated by the user will be executed.

Mode :

- Home : Auto run Home Position (Refet to the Preset

Menu.)

- Preset : Auto run a selected preset number.

- Swing : Auto run a selected Swing mode.

- Group : Auto run a selected Group mode.

- Tour : Auto run a selected Tour mode.

- Trace : Auto run a selected trace mode.

- A.Pan : Auto run a 360-degree pan. To activate the panning command, you need to set up the camera's tilt angle and auto pan speed manually.

Time :

Enables setting up an Auto Run duration. (The duration can be 1~60 seconds, or 1~60 minutes.)

SPEED DOME CAMERA

58

User’s Manual

Functional Description

P/T Setting

16. Pan/Tilt Limit

Main Menu/P/T Setting/Pan/Tilt Limit

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

Auto Track2

Pan/Tilt Limit

① Pan Limit

② Tilt Limit

Pan/Tilt Limit

① Position

② ON/OFF OFF

ON

ON

OFF

The moving ranges in the Pan/Tilt directions can be limited.

Position :

Selecting the Position menu brings up the following screen if it is for the Pan Limit setting. Move the joystick left and right to select a movement range from the starting point to the end.

Start Limit

End Limit

Enter: Set ESC: Exit

Enter: Set ESC: Exit

The following picture shows the Tilt Limit setting.

Move the joystick left and right to select a movement range from the starting point to the end.

Start Limit

Enter: Set ESC: Exit

End Limit

Enter: Set ESC: Exit

On/Off :

Cancels or activates the Pan/Tilt Limit functions.

SPEED DOME CAMERA

59

User’s Manual

Functional Description

17. Area Setting

Main Menu/P/T Setting/Area Setting

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

Area Setting

① Area 1

② Area 2

③ Area 3

④ Area 4

....

Area 1

Area Name

Position

ON/OFF

ON

ON

OFF

OFF

The Area Setting menu enables selecting certain locations in the course of the Pan and Tilt operation, and then display the areas with the OSD (On Screen Display) texts when the camera passes through them. Up to 8 areas can be selected.

Area Name :

You can add names to selected areas. Names can be up to

12 characters and can be entered via the joystick and the

Enter key. Once a name is entered, use the joystick and the

Enter key to perform the Set command and save the name.

Area Name 001[ ]

0123456789()[]#&%/~-=_

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ

ABC->

中文

1 BACK SPACE CLR SET

Position :

As shown in the picture below, move the joystick to select the upper left corner and lower right corner of an area.

Start Position

Enter: Set ESC: Exit

End Position

Enter: Set ESC: Exit

On/Off :

Cancels or activates the display function of selected areas.

SPEED DOME CAMERA

60

User’s Manual

Functional Description

18. Area Masking

Main Menu/P/T Setting/Area Masking

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

Area Setting

① Mask 1

② Mask 1

③ Mask 3

④ Mask 4

....

Mask 1

Position

ON/OFF

ON

ON

OFF

OFF

If a monitoring location includes a highly private area, the area can be selectively excluded from monitoring.

Position :

As shown in the picture below, move the joystick to select the upper left corner and lower right corner of an area.

Start Position

Enter: Set ESC: Exit

End Position

Enter: Set ESC: Exit

On/Off :

Cancels or activates the Area Masking function.

SPEED DOME CAMERA

61

User’s Manual

Functional Description

19. Prop. P/T

Main Menu/P/T Setting/Prop. P&T

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

ON

ON

OFF

This commands the camera to change the Pan and Tilt speed automatically according to the current zoom power. Moving the joystick clockwise (Tele) slows down and counterclockwise

(Wide) accelerates the Pan and Tilt speed, allowing detailed adjustments.

Turning this “Off” executes the function the optical 1x zoom speed regardless of how high a the zoom power is.

Functional Description

20. Digital Flip

Main Menu/P/T Setting/Digital Flip

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

ON

ON

OFF

Digital Flip is useful to monitor a moving object or a person passing directly under the camera.

When an object or a person passes directly under the camera, the camera tilt monitor follows the object or person over 100 degrees to the other side of the tilt area without panning. The screen inversion occurs at 100 degrees or higher and is digitally adjusted.

SPEED DOME CAMERA

62

User’s Manual SPEED DOME CAMERA

63

User’s Manual

Functional Description

21. Image Holding

Main Menu/P/T Setting/Image Hold

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

Auto Track1

⑧ Auto Track2

ON

ON

OFF

When the camera is moving between preset locations, this function stops a previous camera feed until the camera reaches the next location. This is useful to help the screen observer keep sharp eyes and to monitor multiple locations within a network.

SPEED DOME CAMERA

64

User’s Manual

Functional Description

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

① Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

Auto Track 1

Auto Track

Camera Height

Object Size

Sensitivity

Zoom Control

Auto Release

Auto Return

Lost Mode

ON

ON

OFF

OFF

02.5M

SMALL

HIGH

OFF

OFF

OFF

STOP

22. Auto Track 1 (SPD-3750T Only)

Main Menu/P/T Setting/Auto Track1

This function is available only with the SPD-3750T.

This commands the camera to automatically follow a moving object or a person on the screen.

Auto Track :

On/Off: Turns Auto Track on or off.

Camera Height :

Adjusts the height of the camera. Tracking performance may decrease if the camera height is not adjusted properly.

Object Size :

Sets a maximum zoom power to zoom in on an object if the Zoom function is used for the tracking operation.

- Small : Zooms in on a tracking object up to 1/4 of the screen height.

- Medium : Zooms in on a tracking object up to 1/4 of the screen height.

- Large : Zooms in on a tracking object up to 1/4 of the screen height.

Sensitivity :

The object detection sensitivity is adjustable. Lower the sensitivity if the camera catches a swaying tree branch, raindrops, or snowflakes during the Auto Track operation.

Zoom Control :

The function’s zoom control settings are as follows.

- Off : Disables the Zoom control.

- One Shot : Performs the Zoom control once during the

Motion Detection and Auto Track operations.

Depending on the movement detection, the camera performs the Zoom control multiple times.

- Continuous : Performs the Zoom control continuously.

SPEED DOME CAMERA

65

User’s Manual

Functional Description

Auto Release :

Enables setting a maximum duration to follow an object. When the duration expires, the camera stops following the object and looks for another object.

Auto Return :

- Off : Commands the camera to stay on a last spot instead of returning to the initial position.

- Time Setting : Sets a duration for the camera to standby upon the Auto Release expiration and then return to the initial position.

Lost Mode :

Sets up an action for the camera in case the object it is following goes out of the detection range.

- Stop : Commands the camera to stop and abort tracking at the spot where its object disappeared.

- Research : Commands the camera to stop and standby at the spot where its object disappeared.

- Zoom-Out : Commands the camera to zoom out and look for a new object in case its current object disappears.

SPEED DOME CAMERA

66

User’s Manual

Functional Description

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

P/T Setting

Pan/Tilt Limit

② Area Setting

③ Area Masking

Prop. P/T

Digital Flip

Image Hold

⑦ Auto Track1

⑧ Auto Track2

Auto Track 2

① Zone Setting

Indicator

Target Lock

OFF

OFF

ON

ON

OFF

23. Auto Track 2 (SPD-3750T Only)

Main Menu/P/T Setting/Auto Track2

This function is available only with the SPD-3750T.

Auto Track 2 provides Auto Track related settings other than the ones programmed in the Auto Track 1 menu.

Zone Setting :

- Position : Enables designating certain areas as zones for the Auto Track operation. The setting procedures are the same as for Area Mask.

- Mode : Two modes are available: Mask and Alarm. When

Mask is selected, the camera does not follow the object entering the masked zone. This is useful if the camera catches swaying objects such as tree branches and flags during the Auto Track peration.

When Alarm is selected, the camera activates an alarm if an object enters the zone.

- On/Off : Activates or deactivates the Zone function.

Track Zone

Zone 1

② Zone 1

Zone 1

④ Zone 1

⑤ Zone 1

Zone 1

⑦ Zone 1

Zone 1

Zone 1

Position

② Mode

ON/OFF

MASK

OFF

Indicator :

Indicates objects with icons on the screen.

- Off : Disables the Indicator function.

- On : Indicates both the pointer and target.

- Pointer : Indicates the indicator when following an object using the joystick; shows as a cross in the center of the screen.

SPEED DOME CAMERA

67

User’s Manual

Functional Description

- Target : Indicates the camera’s target for the Auto Track operation; when a moving object is detected, a square grid appears and surrounds the object.

Target Lock :

Target Lock is useful to select and follow an object using the Auto Track mode while operating the camera with the joystick. Target Lock can be turned On or Off.

To activate the Auto Track mode, turn on Target Lock, select an object to follow, and then press

Enter.

Notes

•AutoTrackisspecificallytotrackdownintruders.Thus,itmaynotbesuitabletomonitora crowd.

•Ifthecameraisnotsafelysecured,trackingerrorsmayoccur.

•Ifthecameralensissmearedwithforeignsubstancesorisscratched,anerrormay occur causing the camera to not behave as expected.

•Thecameramaynotfollowanobjectortrackingerrorsmayoccurunderthefollowing conditions:

∙ If the contrast between an object and the background is low

∙ If the camera lens is smeared with foreign substances, e.g. raindrops or snowflakes

∙ If the lighting is changing dramatically

If many movements around an object are detected

∙ If an object moves vertically on the optic angle of the camera

∙ If an object passes directly under the camera

∙ If an object creates inconsistent light levels, e.g. the object is too shiny or flickering

In environments where there are light reflections causing internal reflections of camera, e.g. windows, shiny road surfaces, and backlights

∙ If an object moves behind large and tall objects, e.g. telephone poles

∙ If an object moves too quickly

If the camera is vibrating

SPEED DOME CAMERA

68

User’s Manual

Functional Description

OSD Setting

24. OSD Setting

Main Menu/P/T Setting/Pan Tilt Limit

Main Menu

① Camera Setting

Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

OSD Setting

① Camera ID

② Camera Name

③ Preset Number

Preset Name

⑦ PTZ Position

⑧ Language

ON

ON

ON

Sequence Status ON

Area Name OFF

ON

English

Camera ID :

Displays or hides Camera ID in the upper left of the screen.

Camera Name :

Add a name to the camera. (First check the Note.)

Preset Number :

Displays or hides Preset Numbers on the screen.

Preset Name :

Add names to preset locations. (First check the Note.)

Sequence Status :

Displays or hides the status of a sequence action that is in progress.

Area Name :

Displays or hides the Area Name for the Area Settings on the screen.

PTZ Position :

Displays or hides the status of the Pan, Tilt, and Zoom operation that is in progress.

Language :

Enables changing the system language. This camera supports English, Chinese, French, German, Spanish, and

Italian.

XXX Name 001[ ]

0123456789()[]#&%/~-=_

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔߌæÑÛÙŸÁÍÓÚÂ

ABC->

中文

1 BACK SPACE CLR SET

When selecting the Camera Name and Preset

Name, the screen displays the Left keypad.

Names can be up to 12 characters and can be entered via the joystick and the Enter key. Once a name is entered, use the joystick and the Enter key to perform the Set command and save the name.

SPEED DOME CAMERA

69

User’s Manual

Functional Description

Alarm Setting

25. Alarm Setting

25.1. Setting Up Alarm Input

Main Menu/Alarm Setting/Alarm Input

Main Menu

① Camera Setting

② Sequence Setting

P/T Setting

OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Alarm Setting

Alarm Enable

② Alarm Input

③ Alarm Output

④ Aux Output

ALM MOD P SEQ. NO

IN1 OFF 1

IN2 OFF 2

IN3 OFF 3

IN4 OFF 4

OFF

OFF

OFF

OFF

OFF

Alarm Enable :

- On/Off : Enables or disables the Alarm function.

MOD :

Enables selecting an Alarm Input method.

- NO (Normally Open)

IN 1.2.3.4

IN 1.2.3.4

ALM GND

ALARM OFF

- NC (Normally Closed)

IN 1.2.3.4

ALM GND

ALARM ON

IN 1.2.3.4

ALM GND

ALARM OFF

ALM GND

ALARM ON

SPEED DOME CAMERA

70

User’s Manual

Functional Description

Notes

•Asshowninthepictureabove,theAlarmInputmustbeenteredwiththeOpenandClose switch signals. Supplying power without entering the signals may damage the product.

P (Priority) :

Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated,

the alarm with the highest priority activates before the others. Once the alarm is canceled, the next highest priority alarm activates.

SEQ :

Enables setting up a sequence action for the camera in response to an alarm. Available sequence actions are Preset, Swing, Group, Tour, Trace and A.Pan.

SPEED DOME CAMERA

71

User’s Manual

Functional Description

25.2. Alarm Output

Main Menu/Alarm Setting/Alarm Output

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Alarm Setting

Alarm Enable

② Alarm Input

③ Alarm Output

④ Aux Output

Alarm Output

OFF

Setting1 □ 1 □ 2 □ 3 □ 4 □ MD □ TRK

Setting2 □ 1 □ 2 □ 3 □ 4 □ MD □ TRK

Timer 1 OFF

Timer 1 OFF

Setting 1,2 :

Enables selecting an Alarm Output method.

- 1, 2, 3, 4, and MD on the menu selection indicate the alarm input port and motion detection input. Up to 4 alarm inputs can be set for each MD (Motion Detection) and TRK (Auto Track). 1 alarm output port can be used for more than 2 alarm inputs along with ones for MD and

TRK.

The TRK function becomes activated only if the Zone mode under Zone Settings under Auto Track 2 is set to Alarm.

Timer :

Enables selecting an Alarm Output method.

- On : Retains an alarm output for a set duration from a minimum of 1 second to a maximum of 60 hours upon the alarm occurrence.

- Momentary : Retains an alarm output only until the alarm is canceled.

The Alarm Output is equipped with a relay circuit. The operation of the alarm output port is as shown in the diagram below.

NO NO

COM

NC

COM

NC

Alarm Out OFF Alarm Out ON

Notes

•ConnectingthepowerconnectorandGNDincorrectlytotheNC/NOandCOMportsmay cause a short circuit and fire, damaging the camera.

•Themaximumpowercapacityofthebuilt-inrelayis30VDC/2A,125VAC/0.5A,and

250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s lifespan and damage it.

SPEED DOME CAMERA

72

User’s Manual

Functional Description

25.3. Aux Output

Main Menu/Alarm Setting/Aux Output

Main Menu

Camera Setting

Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Alarm Setting

Alarm Enable

② Alarm Input

③ Alarm Output

④ Aux Output

AUX Output

On/Off

Time

OFF

OFF

00 SEC

AUX Output menu is to operate the camera’s peripheral devices such as lamps and sirens through the controller and switches as well as through network communications.

On/Off :

- Cancels or activates the Aux function.

Time :

Enables setting up a duration for the Aux output when the

Aux command is transmitted from the controller. A duration can be selected from a minimum of 1 second to a maximum of 60 minutes.

NO

COM

NO

COM

AUX Off AUX On

Notes

•ConnectingthepowerconnectorandGNDincorrectlytotheAuxterminal’sNOandCOM ports may cause a short circuit and fire, damaging the camera.

•Themaximumpowercapacityofthebuilt-inrelayis30VDC/2A,125VAC/0.5A,and

250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s lifespan and damage it.

SPEED DOME CAMERA

73

User’s Manual

Functional Description

Initialize

26. Initialization Menu

Main Menu/Initialize

Main Menu

① Camera Setting

② Sequence Setting

③ P/T Setting

OSD Setting

Alarm Setting

⑥ Initialize

Status

Initialize

① Power On Reset

Factory Default

③ Camera Default

Auto Refresh

⑤ Auto Track Default

OFF

Power On Reset :

Restarts the camera.

Factory Default :

Enables resetting the camera to its factory default settings.

When the mode is selected, all custom data such as preset locations is deleted from the camera. Use this function if it is necessary to reset the settings of the camera.

Camera Default :

This mode can be used if the camera module has been replaced and you want to keep the camera's existing settings for the new module. To do reset the camera, first replace the old module with a new camera module. When the replacement is properly installed, turn on the module, then execute this command.

Auto Refresh :

Enables optimizing the status of the camera’s built-in electric circuits and components on a regular basis. (A regular operation can be scheduled.) This mode can be used to maintain and repair the current settings of the camera when anomalous operations occur: e.g. The camera happened to directly face a light source, or the settings have been canceled after the camera repeatedly rotated in all four directions for a long time to monitor a specific location. The default setting is Off.

- Off, 1~7 Days: Selecting Off disables Auto Refresh and but automatically executes it after 1~7 Days days has passed. action once the refresh is complete.

Auto Refresh takes approximately 10 seconds to finish.

If Auto Refresh activates in the middle of a sequence action, the camera pauses the sequence action and performs an Auto Refresh, then resumes the sequence action once the refresh is complete.

SPEED DOME CAMERA

74

User’s Manual

Operating Your Camera

Initial Position :

Initial Position can be used to designate the camera’s stop location after it is initialized. This function is useful in an environment where the camera has to be frequently turned on and off.

Auto Track Default :

Enables resetting the Auto Track settings.

SPEED DOME CAMERA

75

User’s Manual

Operating Your Camera

Status

27. Status

Main Menu/Status

Main Menu

Camera Setting

Sequence Setting

③ P/T Setting

④ OSD Setting

⑤ Alarm Setting

⑥ Initialize

Status

Camera Status

CAM MODEL = 37PC

CAM VERSION = 2.3

DOME VERSION = 0.10

CON PROTOCOL = SAMSUNG TW

DOME ID = 001

CONTROLLER = Simplex-9600

TRACK VERSION = 0.10

Displays the settings and version of the dome camera.

Cam Model :

Indicates the model name of the camera.

Cam Version :

Indicates the software version of the camera.

Dome Version :

Indicates the version of the camera control board.

CON Protocol :

Indicates the status of the current protocol.

Dome ID :

Dome Camera ID

Controller :

Indicates the settings of the current communications mode.

Track Version :

Indicates the Auto Track software version of the camera.

SPEED DOME CAMERA

76

User’s Manual

Imaging Device

TV Standard

Total Pixels

Effective Pixels

Scanning System

Synchronization

Horizontal Scan Rate

Vertical Scan Rate

Horizontal Resolution

Min. Illumination

S/N (Y Signal)

Video Output

Zoom Ratio

Focal Length

Min. Object Distance

Angular Field of view

Focus

Zoom Speed

IRIS

Lens Initialization

Auto Tracking

Horizontal

Rotation Angle

Horizontal

Rotation Speed

Vertical Rotation Angle

Vertical Rotation Speed

Preset Position

Preset Accuracy

Camera ID

Day & Night

Backlight

Dynamic Range

Motion Detection

Stabilizer

Privacy Mask

SSNR

Sens-up

Gain Control

White Balance

Product Specification

SPD-3750T SPD-3750

1/4 inch, Double Density Interline Transfer CCD

SPD-3350

Internal

NTSC

811(H) x 508(V)

768(H) x 494(V)

2:1 Interlace

Internal/External(AC Line Lock)

15.734 KHz

59.94 Hz

550 TV Line(Color)/680 TV Line(B/W)

0.7 Lux (50 IRE @ F1.6 Color), 0.0001 Lux ( Sens-up, 256x )

0.1 Lux (50 IRE, B/W )

50 dB

CVBS:1.0Vp-p/75Ω

37X (Optical),12X (Digital)

3.5~129.5mm (F1.6 ~3.9)

33X (Optical),12X (Digital)

3.5~115.5mm (F1.6 ~3.6)

1.9m

H:55.5°(Wide)~1.59°(Tele)

V:42.5°(Wide)~1.19°(Tele)

H:55.5°(Wide)~1.77°(Tele)

V:42.5°(Wide)~1.33°(Tele)

AUTO / MANUAL / ONE-SHOT

2.5sec

AUTO/MANUAL

Built-In

Built-In -

360° Endless

Manual:0.024°/sec ~120°/sec, Preset 500°/sec

-5° ~ 185°

Manual:0.024°/sec ~120°/sec, Preset 500°/sec

255

±0.1°

255

AUTO / COLOR / BW

WDR / USER / HLC / OFF

52dB

ON/OFF

ON/OFF

ON/OFF (8 Areas)

LOW/MEDIUM/HIGH/OFF

On/Off (Selectable limit ~ 256X )

LOW/MEDIUM/HIGH/MANUAL/OFF

ATW/INDOOR/OUTDOOR/AWC/MANUAL

SPEED DOME CAMERA

77

User’s Manual

Product Specification

Electronic Shutter

Serial Com.

Protocol

Alarm

Digtal Flip

Operating Temperature/

Humidity

Storage Temperature/

Humidity

Input Voltage

Power Consumption

External Dimensions

( Ø ×D)

Weight

AUTO(1/60~120,000sec)/MANUAL/A.FLK

RS-422/485

Samsung Techwin, Pelco-D, Pelco-P, Panasonic, Honeywell, AD, Vicon, Samsung Electronics

4 In, 2 Out, 1 Aux

ON/OFF

-10 ℃ to +50 ℃ / 20% to 80% RH

Max. 15W

-20

to +60

/ 20% to 95% RH

AC24V ± 10%

Max. 13W

Ø155×243.4mm

2Kg

SPEED DOME CAMERA

78

User’s Manual

DECLARATION OF CONFORMITY

Application of Council Directive(s)

Manufacturer's Name

Manufacturer's Address

EMC-Directive 92/31 EEC and its amendments

SAMSUNG TECHWIN CO., LTD

SAMSUNG TECHWIN CO., LTD

42,SUNGJU-DONGCHANGWON-CITY,

KYUNGNAM,KOREA,641-716

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

YearofManufacture

Conformance to

Dome Camera

SPD-3750T/3750/3350

S8110001

2008.11.29

EN 55022 : 2006

EN 50130-4 : 2003

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD

Signature

FullName

Position

HANSEUGKIM

QUALITYCONTROLMANAGER

Place

Date

CHANGWON,KOREA

2008.11.29

Legal Representative in Europe

Signature

FullName

Position

Place

Date

SPEED DOME CAMERA

79

User’s Manual

SALES NETWORK

SAMSUNG TECHWIN CO.,LTD.

145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea

TEL : +82-31-740-8151~8 FAX : +82-31-740-8145

SAMSUNG TECHWIN AMERICA,LTD.

1480 Charles Willard St. Carson, CA 90746, UNITED STATES

TEL : +1-310-632-1234 FAX : +1-310-632-2195

SAMSUNG OPTO-ELECTRONICS UK,LTD.

Samsung House, 1000 Hillswood Drive, Hillswood

Business Park Chertsey Surrey KT16 OPS

TEL :

+44-1932-45-5308 FAX : +44-1932-45-5325

www.samsungtechwin.com

www.samsungcctv.com

S.No:Z6806093201A

VAN 08. 12

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages