Carbine M16A2 W/E, M16A3 W/E, M16A4 W/E Rifle, M4, M4A1 Technical Manual

*ARMY TM 9-1005-319-23&P
AIR FORCE TO 11W3-5-5-42
NAVY SW370-BU-MMI-010
TECHNICAL MANUAL
FIELD MAINTENANCE MANUAL
(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)
FOR
RIFLE, 5.56MM, M16A2 W/E, PN 9349000
NSN 1005-01-128-9936 (EIC:4GM);
RIFLE, 5.56MM, M16A3 W/E, PN 12012000
NSN 1005-01-357-5112;
RIFLE, 5.56MM, M16A4 W/E, PN 12973001
NSN 1005-01-383-2872 (EIC:4F9);
CARBINE, 5.56MM, M4, PN 9390000
NSN 1005-01-231-0973 (EIC:4FJ);
CARBINE, 5.56MM, M4A1, PN 12972700
NSN 1005-01-382-0953 (EIC:4GC)
*Supersedes TM 9-1005-319-23&P, 11W3-5-5-42, and SW370-BU-MMI-010. 01 May 1991, including all changes.
DISCLOSURE NOTICE - This information is furnished upon the condition that it will not be released to another nation without
the specific authority of the Department of the Army of the United States; that it will be used for military purposes only; that
individual or corporate rights originating in the information, whether patented or not, will be respected; that the recipient will
report promptly to the United States any known or suspected compromise; and that the information will be provided
substantially the same degree of security afforded it by the Department of Defense of the United States. Also, regardless of
any other markings on the document, it will not be downgraded or declassified without written approval of the originating United
States agency.
DISTRIBUTION STATEMENT C - Distribution authorized to U.S. Government agencies and their contractors. This publication
is required for administration and operational purposes, as determined 26 October 2005. ARMY ONLY: Other requests for
this document shall be referred to U.S. Army TACOM Life Cycle Management Command, ATTN: AMSTA-LC-LMPP/TECH PUBS,
1 Rock Island Arsenal, Rock Island, IL 61299-7630. AIR FORCE ONLY: Other requests for this document must be referred to
542 CBSS/GBHDE, Robins AFB, GA 31098-1813.
WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C.,
Sec 2751 et seq) or the Export Administration Act of 1979, as amended, Title 50A, U.S.C., App. Violations of these export
laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DOD Directive 5230.25.
DESTRUCTION NOTICE - Destroy by any method that will prevent disclosure of contents or reconstruction of the document.
DEPARTMENTS OF THE ARMY, AIR FORCE, AND NAVY
NOVEMBER 2008
TM 9-1005-319-23&P
WARNING SUMMARY
This warning summary contains general safety warning and hazardous materials warnings that must be
understood and applied during operation and maintenance of this equipment. All warnings in this technical
manual pertain to both the rifles and the carbines unless otherwise specified. Failure to observe these
precautions could result in serious injury or death to personnel. Also included are explanations of safety
and hazardous materials icons used within the technical manual.
FIRST AID
For first aid information, refer to FM 4-25.11, First Aid. Air Force users will refer to Air Force Manual
AFMAN 44-163(I), First Aid Manual.
EXPLANATION OF SAFETY WARNING ICONS
EXPLOSION - rapidly expanding symbol shows that the material may explode if subjected
to high temperatures, sources of ignition, or high pressure.
EYE PROTECTION - person with goggles shows that the material will injure the eyes.
FLYING PARTICLES - arrows bouncing off face shows that particles flying through the air
will harm face.
WEAPON FIRE - weapon could accidentally discharge causing serious injury or death.
GENERAL SAFETY WARNINGS DESCRIPTION
WARNING
To avoid injury to eyes, use care when removing and installing spring-loaded parts.
WARNING
WEAPON FIRE
Before starting an inspection, be sure to clear the weapon. Do not pull the trigger until the weapon has been
cleared. Inspect the chamber to ensure that it is empty and no ammunition is in position to be chambered.
The lock plate prevents the selector lever from being placed in BURST and will be installed at the discretion
of the unit commander. It is mandatory for use in civil disturbance (riot control).
a
TM 9-1005-319-23&P
WARNING SUMMARY - Continued
GENERAL SAFETY WARNINGS DESCRIPTION - Continued
WARNING
EXPLOSION
Do not keep live ammunition near work area.
If the weapon fails function tests, perform required maintenance. Continued use of weapon could result in
injury to, or death of, personnel.
All M16A2, M16A3, M16A4 rifles and M4/M4A1 carbines must be inspected and gaged at least once
annually for safety and serviceability. Initial gaging is required 1 year from receipt of the weapons. Air
Force users refer to inspection requirements in the Air Force Instruction (AFI) 36-2226.
All Army Reserve and Army National Guard M16A2 rifles and M4 carbines must be inspected and gaged at
least once every 2 years, after the initial inspection/gaging procedures have been accomplished. This initial
gaging procedure is required 1 year from receipt of the weapons. This 2 year interval may be maintained
unless preventive maintenance checks and services (PMCS) or other physical evidence indicates that an
individual unit's M16A2 rifles and M4 carbines require inspection/gaging at a more frequent interval. If it
is determined that a yearly inspection is necessary for an individual unit, only that unit will be affected.
This will not affect the interval of inspection for other units.
It is recommended that training units inspect/gage all rifles and carbines at the end of each training cycle.
Training units will inspect/gage all rifles and carbines at least once annually.
Unless performed by qualified maintenance personnel, DO NOT interchange bolt assemblies from one
rifle/carbine to another. Doing so may result in injury to, or death of, personnel.
Bolt cam pin must be installed or rifle/carbine will blow up while firing the first round. If the bolt cam pin is
not installed, injury to or death of personnel may result.
The lock plate prevents the selector lever from being placed in BURST and will be installed at the discretion
of the unit commander. It is mandatory for use in civil disturbance (riot control).
Only blank cartridge M200 is to be used when the blank firing attachment (BFA) is attached to the carbine
rifle. Ensure that the blank firing attachment (BFA) is removed before using live ammo. Use of live ammo
with the BFA attached will result in a blown weapon and personal injuries.
Do not fire blank ammunition at a target at distances of less than 20 feet (6.10 m). The unburned propellant
grains can cause injury within this distance.
For further information on safety, care, and handling of ammunition, Army users will refer to TM 9-1005319-10. Air Force users should refer to AFI 21-201, Management and Maintenance of Non-Nuclear
Munitions, and AFMAN 91-201, Explosives Safety Standards.
Any screw longer than 1 1/8 inch used with enhanced rifle grip part number 93949127 could make the
disconnector inoperable, and the weapon will not be able to fire in the burst mode. The loss of burst
capability in a tactical situation could put the operator at risk. Ensure that the washer is in place.
b
TM 9-1005-319-23&P
WARNING SUMMARY - Continued
EXPLANATION OF HAZARDOUS MATERIALS ICONS
CHEMICAL - drops of liquid on hand shows that the material will cause burns or irritation
to human skin or tissue.
EYE PROTECTION - person with goggles shows that the material will injure the eyes.
FIRE - flame shows that a material may ignite and cause burns.
VAPOR - human figure in a cloud shows that material vapors present danger to life or
health.
HAZARDOUS MATERIALS DESCRIPTION
WARNING
DRY CLEANING SOLVENT
Dry cleaning solvent is flammable and toxic and should be used in a well-ventilated area. Do not clean parts
near an open flame or in a smoking area. Cleaning solvent evaporates quickly and has a drying effect on the
skin. The use of protective gloves is necessary to protect the skin when cleaning weapon parts.
WARNING
SOLID FILM LUBRICANT
The ingredient, methylene chloride, is considered carcinogenic. Wear eye and skin protection and be sure
the area is well-ventilated. Wash exposed skin thoroughly with soap and water.
WARNING
DICHLOROMETHANE
The ingredient, methylene chloride, is considered carcinogenic. Wear eye and skin protection and be sure
the area is well-ventilated. Wash exposed skin thoroughly with soap and water.
c
TM 9-1005-319-23&P
WARNING SUMMARY - Continued
HAZARDOUS MATERIALS DESCRIPTION - Continued
WARNING
CARBON REMOVING COMPOUND
When using carbon removing compound, avoid skin contact. If carbon removing compound comes in contact
with the skin, wash thoroughly with running water. Using a good lanolin base cream after exposure to the
compound is helpful. The use of gloves and protective equipment is required.
d
TM 9-1005-319-23&P
LIST OF EFFECTIVE PAGES/WORK PACKAGES
NOTE: This manual supersedes TM 9-1005-319-23&P, 11W3-5-5-42, and SW370-BU-MMI-010,
01 May 1991. Zero in the "Change No." column indicates an original page or work package.
Date of issue for the original manual is:
Original
28 November 2008
TOTAL NUMBER OF PAGES FOR FRONT AND REAR MATTER IS 40 AND TOTAL NUMBER
OF WORK PACKAGES IS 45 CONSISTING OF THE FOLLOWING:
Page/WP No.
Change No.
Front Cover.................................
Warning summary (4 pgs) .........
A ..................................................
B blank........................................
i - xi .............................................
xii blank ......................................
Chapter 1 title page ...................
WP 0001 (8 pgs)..........................
WP 0002 (6 pgs)..........................
WP 0003 (4 pgs)..........................
Chapter 2 title page ...................
WP 0004 (2 pgs)..........................
WP 0005 (22 pgs)........................
Chapter 3 title page ...................
WP 0006 (2 pgs)..........................
WP 0007 (2 pgs)..........................
WP 0008 (28 pgs)........................
WP 0009 (18 pgs)........................
WP 0010 (6 pgs)..........................
WP 0011 (8 pgs)..........................
WP 0012 (10 pgs)........................
WP 0013 (4 pgs)..........................
WP 0014 (2 pgs)..........................
WP 0015 (26 pgs)........................
WP 0016 (10 pgs)........................
WP 0017 (4 pgs)..........................
WP 0018 (4 pgs)..........................
WP 0019 (14 pgs)........................
WP 0020 (2 pgs)..........................
WP 0021 (22 pgs)........................
WP 0022 (6 pgs)..........................
WP 0023 (2 pgs)..........................
WP 0024 (4 pgs)..........................
WP 0025 (10 pgs)........................
WP 0026 (2 pgs)..........................
WP 0027 (4 pgs)..........................
WP 0028 (2 pgs)..........................
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Page/WP No.
Change No.
WP 0029 (10 pgs)........................
WP 0030 (8 pgs) ..........................
Chapter 4 title page ...................
WP 0031 (2 pgs) ..........................
WP 0032 (6 pgs) ..........................
WP 0033 (6 pgs) ..........................
WP 0034 (6 pgs) ..........................
WP 0035 (4 pgs) ..........................
WP 0036 (6 pgs) ..........................
WP 0037 (8 pgs) ..........................
Chapter 5 title page ...................
WP 0038 (8 pgs) ..........................
WP 0039 (60 pgs)........................
WP 0040 (4 pgs) ..........................
WP 0041 (4 pgs) ..........................
Chapter 6 title page ...................
WP 0042 (4 pgs) ..........................
WP 0043 (4 pgs) ..........................
WP 0044 (4 pgs) ..........................
WP 0045 (6 pgs) ..........................
Index-1 - Index-7 ........................
Index-8 blank..............................
A/B blank
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
*ARMY TM 9-1005-319-23&P
AIR FORCE TO 11W3-5-5-42
NAVY SW370-BU-MMI-010
HEADQUARTERS
DEPARTMENTS OF THE ARMY,
AIR FORCE, AND NAVY
WASHINGTON, D.C., 28 November 2008
TECHNICAL MANUAL
FIELD MAINTENANCE MANUAL
(INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST)
FOR
RIFLE, 5.56MM, M16A2 W/E, PN 9349000
NSN 1005-01-128-9936 (EIC:4GM);
RIFLE, 5.56MM, M16A3 W/E, PN 12012000
NSN 1005-01-357-5112;
RIFLE, 5.56MM, M16A4 W/E, PN 12973001
NSN 1005-01-383-2872 (EIC:4F9);
CARBINE, 5.56MM, M4, PN 9390000
NSN 1005-01-231-0973 (EIC:4FJ);
CARBINE, 5.56MM, M4A1, PN 12972700
NSN 1005-01-382-0953 (EIC:4GC)
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this publication. If you find any errors, or if you would like to recommend any improvements to
the procedures in this publication, please let us know. Reports, as applicable by the requiring Service, should be
submitted as follows:
(a) (A) Army - The preferred method is to submit your DA Form 2028 (Recommended Changes to Publications and Blank
Forms) through the Internet, on the Army Electronic Product Support (AEPS) website. The Internet address is
https://aeps.ria.army.mil. The DA Form 2028 is located under the Public Applications section in the AEPS Public Home
Page. Fill out the form and click on SUBMIT. Using this form on the AEPS will enable us to respond quicker to your
comments and better manage the DA Form 2028 program. You may also mail, e-mail, or fax your comments or DA Form
2028 directly to the U.S. Army TACOM Life Cycle Management Command. The postal mail address is U.S. Army
TACOM Life Cycle Management Command, ATTN: AMSTA-LC-LMPP / TECH PUBS, 1 Rock Island Arsenal, Rock
Island, IL 61299-7630. The e-mail address is [email protected]. The fax number is DSN 793-0726 or
Commercial (309) 782-0726.
(b) (N) Navy - By letter directly to Commander, Code 4081, Bldg. 2521, NAVSURF WARCENDIV, 300 Hwy 361, Crane,
IN 47522-5001. You may also send in your recommended changes via electronic mail or by fax.
(c) (F) Air Force - By Air Force AFTO Form 22 through your respective MAJCOM in the Joint Computer-aided
Acquisition and Logistics Support (JCALS) system. Refer to Section 5 of Air Force Technical Order 00-5-1 for guidance.
A reply will be furnished to you.
*Supersedes TM 9-1005-319-23&P, 11W3-5-5-42, and SW370-BU-MMI-010, 01 May 1991, including all changes.
i
TM 9-1005-319-23&P
DISCLOSURE NOTICE - This information is furnished upon the condition that it will not be released to another nation
without the specific authority of the Department of the Army of the United States; that it will be used for military
purposes only; that individual or corporate rights originating in the information, whether patented or not, will be
respected; that the recipient will report promptly to the United States any known or suspected compromise; and that the
information will be provided substantially the same degree of security afforded it by the Department of Defense of the
United States. Also, regardless of any other markings on the document, it will not be downgraded or declassified
without written approval of the originating United States agency.
DISTRIBUTION STATEMENT C - Distribution authorized to U.S. Government agencies and their contractors. This
publication is required for administration and operational purposes, as determined 26 October 2005. ARMY ONLY:
Other requests for this document shall be referred to U. S. Army TACOM Life Cycle Management Command, ATTN:
AMSTA-LC-LMPP/TECH PUBS, 1 Rock Island Arsenal, Rock Island, IL 61299-7630. AIR FORCE ONLY: Other
requests for this document must be referred to 542 CBSS/GBHDE, Robins AFB, GA 31098-1813.
WARNING - This document contains export-controlled technical data whose export is restricted by the Arms Export
Control Act (Title 22, U.S.C., Sec 2751 et seq) or the Export Administration Act of 1979, as amended, Title 50A, U.S.C.,
App. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions
of DOD Directive 5230.25.
DESTRUCTION NOTICE - Destroy by any method that will prevent disclosure of contents or reconstruction of the
document.
TABLE OF CONTENTS
WP Sequence No.
Page No.
Warning Summary
How To Use This Manual
CHAPTER 1 — GENERAL INFORMATION, EQUIPMENT DESCRIPTION,
AND THEORY OF OPERATION
General Information ..................................................................................................................
Figure 1. External View of 5.56mm Rifle, M16A2 .................................0001-1
Figure 2. External View of 5.56mm Rifle, M16A3 and M16A4 ............0001-2
Figure 3. External View of 5.56mm Carbine, M4/M4A1 .......................0001-3
Equipment Description and Data .............................................................................................
Figure 1. Major Components of Rifles and Carbines.............................0002-2
Theory of Operation ...................................................................................................................
Figure 1. Operation of Rifles and Carbines............................................0003-2
CHAPTER 2 — FIELD TROUBLESHOOTING PROCEDURES
Troubleshooting Index ...............................................................................................................
Troubleshooting Procedures......................................................................................................
Table 1.
Troubleshooting Procedures....................................................0005-1
Figure 1. Magazine Catch Inspection .....................................................0005-2
Figure 2. Magazine Catch and Spring Inspection .................................0005-3
Figure 3. Action Spring............................................................................0005-3
Figure 4. Bolt Carrier Assembly Inspection...........................................0005-4
Figure 5. Extractor Spring Assembly Inspection...................................0005-4
Figure 6. Gas Tube...................................................................................0005-5
Figure 7. Action Spring Inspection .........................................................0005-5
Figure 8. Hammer and Burst Cam Inspection.......................................0005-6
Figure 9. Firing Pin Retaining Pin Inspection.......................................0005-7
Figure 10. Selector Lever and Firing Pin Inspection...............................0005-7
ii
WP 0001
WP 0002
WP 0003
WP 0004
WP 0005
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 2 — FIELD TROUBLESHOOTING PROCEDURES (Continued)
Figure 11. Locking Lugs Inspection..........................................................0005-8
Figure 12. Cartridge Extractor Inspection ...............................................0005-8
Figure 13. Cartridge Ejector Inspection ...................................................0005-9
Figure 14. Trigger and Hammer Inspection...........................................0005-10
Figure 15. Disconnector, Automatic Sear, and Burst Cam Inspection.0005-11
Figure 16. Action Spring Replacement...................................................0005-12
Figure 17. Bolt Ring Gap Adjustment ....................................................0005-12
Figure 18. Bolt Carrier Key Inspection ..................................................0005-13
Figure 19. Adjustment of Gas Tube ........................................................0005-13
Figure 20. Barrel Gas Port Cleaning ......................................................0005-14
Figure 21. Front Sight and Rear Sight Inspection ................................0005-15
Figure 22. Automatic Sear and Selector Lever Inspection....................0005-16
Figure 23. Burst Disconnector and Burst Cam Inspection ...................0005-17
Figure 24. Selector Lever and Automatic Sear Inspection....................0005-18
Figure 25. Semiautomatic Disconnector and Hammer Inspection .......0005-19
Figure 26. Trigger and Pin Hole Inspection...........................................0005-19
Figure 27. Selector Lever and Trigger Inspection .................................0005-20
Figure 28. Hammer Pin Inspection.........................................................0005-20
Figure 29. Magazine Inspection ..............................................................0005-21
Figure 30. Bolt Catch Inspection ............................................................0005-22
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS
Service Upon Receipt .................................................................................................................
Preventive Maintenance Checks and Services (PMCS) Introduction ....................................
Preventive Maintenance Checks and Services, Including Lubrication Instructions ............
Table 1.
Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines ............................0008-2
Rifle, 5.56mm (M16A2) 9349000; Rifle, 5.56mm (M16A3) 12012000;
Rifle, 5.56mm (M16A4) 12973001; Carbine, 5.56mm (M4) 9390000;
and Carbine, 5.56mm (M4A1) 12972700 Maintenance........................................................
Figure 1. Major Components of Rifles and Carbines.............................0009-2
Figure 2. Trigger Pull Test ......................................................................0009-7
Figure 3. Beginning Position in Three-Round Burst.............................0009-8
Figure 4. Firing of First Round ...............................................................0009-9
Figure 5. Movement of Key and Bolt Carrier Assembly .......................0009-9
Figure 6. First Rotation of Burst Cam..................................................0009-10
Figure 7. Action of Automatic Sear.......................................................0009-10
Figure 8. Burst Disconnector in Second Notch ....................................0009-10
Figure 9. Forward Travel of Key and Bolt Carrier Assembly.............0009-11
Figure 10. Firing of Second Round .........................................................0009-11
Figure 11. Rearward Movement of Key and Bolt Carrier Assembly....0009-12
Figure 12. Second Rotation of Burst Cam ..............................................0009-12
Figure 13. Second Round Action of Automatic Sear..............................0009-12
Figure 14. Burst Disconnector in Third Notch.......................................0009-13
Figure 15. Release of Hammer Assembly...............................................0009-13
Figure 16. Firing of Third Round............................................................0009-13
iii
WP 0006
WP 0007
WP 0008
WP 0009
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS (Continued)
Figure 17. Final Movement of Key and Bolt Carrier Assembly............0009-14
Figure 18. Third Rotation of Burst Cam ................................................0009-14
Figure 19. Rotation into Stop Notch .......................................................0009-15
Figure 20. Completion of Firing ..............................................................0009-15
Figure 21. Release of Trigger ..................................................................0009-16
Figure 22. Stowage of Weapon ................................................................0009-17
Back-up Iron Sight Maintenance..............................................................................................
Figure 1. Removal of Back-up Iron Sight ...............................................0010-2
Figure 2. Disassembly/Assembly of BUIS ..............................................0010-3
Figure 3. Installation of Back-up Iron Sight ..........................................0010-5
Bolt and Bolt Carrier Assembly Maintenance .........................................................................
Figure 1. Disassembly of Bolt and Bolt Carrier Assembly....................0011-2
Figure 2. Cleaning of Bolt Carrier Assembly .........................................0011-2
Figure 3. Inspection Points......................................................................0011-3
Figure 4. Inspection of Carrier Key Screws ...........................................0011-4
Figure 5. Inspection of Firing Pin ...........................................................0011-4
Figure 6. Firing Pin Protrusion Test ......................................................0011-5
Figure 7. Checking for Binding of Bolt Assembly..................................0011-5
Figure 8. Checking for Fit of Bolt Assembly ..........................................0011-6
Figure 9. Repair of Carrier Key ..............................................................0011-6
Figure 10. Assembly of Bolt and Bolt Carrier Assembly.........................0011-7
Breech Assembly Bolt Maintenance .........................................................................................
Figure 1. Removal of Cartridge Extractor..............................................0012-2
Figure 2. Removal of Spring Pin .............................................................0012-2
Figure 3. Removal of Cartridge Ejector..................................................0012-3
Figure 4. Removal of Bolt Rings .............................................................0012-3
Figure 5. Bolt Face Inspection ................................................................0012-4
Figure 6. Inspection for Cracks in Bolt Assembly .................................0012-4
Figure 7. Inspection of Firing Pin Hole ..................................................0012-5
Figure 8. Inspection of Bolt Assembly Parts ..........................................0012-6
Figure 9. Installation of Bolt Rings ........................................................0012-7
Figure 10. Installation of Cartridge Ejector.............................................0012-7
Figure 11. Installation of Spring Pin ........................................................0012-8
Figure 12. Installation of Extractor Spring Assembly ............................0012-8
Figure 13. Installation of Extractor Pin ...................................................0012-9
Key and Bolt Carrier Assembly Maintenance .........................................................................
Figure 1. Disassembly of Key and Bolt Carrier Assembly ....................0013-1
Figure 2. Installation of Carrier Key ......................................................0013-2
Figure 3. Torquing Carrier Key Screws..................................................0013-2
Figure 4. Staking Carrier Key Screws....................................................0013-3
Figure 5. Staking Carrier Key Screws in the Field ...............................0013-3
Charging Handle Assembly Maintenance................................................................................
Figure 1. Disassembly of Charging Handle Assembly ..........................0014-1
Figure 2. Assembly of Charging Handle Assembly ...............................0014-2
iv
WP 0010
WP 0011
WP 0012
WP 0013
WP 0014
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS (Continued)
Upper Receiver and Barrel Assembly (M16A2, M16A3) 9349050,
(M16A4) 12973010, and (M4, M4A1) 12972680 Maintenance ............................................
Figure 1. Removal of Upper Handguard Assembly (M16A2)................0015-2
Figure 2. Removal of Lower Handguard Assembly (M16A2)................0015-3
Figure 3. Removal of Upper and Lower Handguards
(M16A3/M16A4/M4/M4A1)......................................................0015-3
Figure 4. Removal of Barrel Stop Assembly...........................................0015-3
Figure 5. Removal of Spring Pin .............................................................0015-4
Figure 6. Removal of Gas Tube ...............................................................0015-4
Figure 7. Removal of Compensator.........................................................0015-5
Figure 8. Removal of Recessed Washer ..................................................0015-5
Figure 9. Loosening of Barrel Nut Assembly .........................................0015-6
Figure 10. Separation of Upper Receiver Assembly
and Barrel Assembly ...............................................................0015-6
Figure 11. Removal of Handguard Slip Ring ...........................................0015-7
Figure 12. Inspection of Handguard Assemblies .....................................0015-8
Figure 13. Bore Inspection ........................................................................0015-9
Figure 14. Alignment of Compensator......................................................0015-9
Figure 15. Inspection of Chamber...........................................................0015-10
Figure 16. Inspection for Corrosion ........................................................0015-10
Figure 17. Inspection for Shiny Surfaces ...............................................0015-12
Figure 18. Installation of Handguard Slip Ring ....................................0015-13
Figure 19. Alignment of Barrel Assembly and Upper
Receiver Assembly .................................................................0015-14
Figure 20. Torquing of Barrel Nut Assembly.........................................0015-15
Figure 21. Alignment of Front and Rear Sights ....................................0015-16
Figure 22. Alignment of Barrel Nut Assembly ......................................0015-17
Figure 23. Installation of Compensator..................................................0015-18
Figure 24. Alignment of Compensator....................................................0015-18
Figure 25. Installation of Gas Tube ........................................................0015-19
Figure 26. Installation of Spring Pin ......................................................0015-19
Figure 27. Installation of Barrel Stop Assembly ...................................0015-20
Figure 28. Installation of Upper Handguard Assembly
(M16A3/M16A4/M4/M4A1)....................................................0015-20
Figure 29. Installation of Lower Handguard
(M16A3/M16A4/M4/M4A1)....................................................0015-21
Figure 30. Installation of Upper Handguard Assembly (M16A2).........0015-21
Figure 31. Installation of Lower Handguard Assembly (M16A2).........0015-22
Figure 32. Use of Barrel Erosion Gage ...................................................0015-23
Figure 33. Use of Barrel Straightness Gage ..........................................0015-24
Figure 34. Insertion of Headspace Gage.................................................0015-25
Figure 35. Checking Headspace ..............................................................0015-25
Figure 36. Use of Weights in Headspace Check.....................................0015-26
v
WP 0015
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS (Continued)
Barrel Assembly (M16A2, M16A3) 9349124, (M16A4) 12598107,
Replacement Barrel and Front Sight Assembly (M4) 9390007,
(M4A1) 12991851 Maintenance .............................................................................................
Figure 1. Removal/Installation of Front Sight Post...............................0016-2
Figure 2. Removal/Installation of Front Sight Detent and Spring.......0016-2
Figure 3. Removal of Small Sling Swivel (Rifle) ....................................0016-3
Figure 4. Removal/Installation of Spring Pins (Carbine)......................0016-3
Figure 5. Removal/Installation of Locking Bar (Carbine) .....................0016-4
Figure 6. Removal/Installation of Swivel Mount (Carbine) ..................0016-4
Figure 7. Disassembly/Assembly of Swivel Mount (Carbine) ...............0016-5
Figure 8. Repair of Bent Front Sight Assembly.....................................0016-5
Figure 9. Installation of Small Sling Swivel (Rifle)...............................0016-8
Figure 10. Measurement of Height of Front Sight Post ..........................0016-9
Figure 11. Adjustment of Front Sight Post ............................................0016-10
Figure 12. Final Measurement of Height ...............................................0016-10
Upper Handguard Assembly and Barrel Stop Assembly
(M16A3, M16A4) Maintenance ..............................................................................................
Figure 1. Placement of Handguard Assembly for Repair......................0017-1
Figure 2. Disassembly/Assembly of Handguard Assembly ...................0017-2
Figure 3. Repair of Barrel Stop Assembly..............................................0017-2
Upper Handguard Assembly (M4, M4A1) Maintenance .........................................................
Figure 1. Placement of Handguard Assembly for Repair......................0018-2
Figure 2. Disassembly/Assembly of Handguard Assembly ...................0018-2
Upper Receiver Assembly and Rear Sight Assembly Maintenance .......................................
Figure 1. Removal of Ejection Port Cover ..............................................0019-2
Figure 2. Removal of Windage Knob ......................................................0019-3
Figure 3. Removal of Sight Aperture ......................................................0019-3
Figure 4. Disassembly of Rear Sight Assembly .....................................0019-4
Figure 5. Removal of Forward Assist Assembly ....................................0019-5
Figure 6. Straightening Rear Sight Guards...........................................0019-6
Figure 7. Installation of Forward Assist Assembly ...............................0019-7
Figure 8. Assembly and Installation of Elevation Knob Assembly ......0019-8
Figure 9. Installation of Rear Sight Base...............................................0019-9
Figure 10. Installation of Helical Spring................................................0019-10
Figure 11. Installation of Sight Aperture and Windage Knob..............0019-10
Figure 12. Installation of Ejection Port Cover .......................................0019-11
Figure 13. Zeroing Elevation Knob .........................................................0019-12
Figure 14. Centering Rear Sight.............................................................0019-13
Figure 15. Adjustment of Rear Sight ......................................................0019-13
Figure 16. Visual Verification .................................................................0009-14
Forward Assist Assembly Maintenance ...................................................................................
Figure 1. Disassembly of Forward Assist Assembly..............................0020-1
Figure 2. Assembly of Forward Assist Assembly...................................0020-2
Lower Receiver and Buttstock Assembly Maintenance ..........................................................
Figure 1. Removal of Pistol Grip.............................................................0021-2
Figure 2. Removal of Machine Screw......................................................0021-2
Figure 3. Removal of Buttstock Assembly (Rifle) ..................................0021-3
Figure 4. Removal of Buttstock Assembly (Carbine).............................0021-4
vi
WP 0016
WP 0017
WP 0018
WP 0019
WP 0020
WP 0021
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS (Continued)
Figure 5. Removal of Pivot Pin................................................................0021-4
Figure 6. Removal of Detent and Helical Spring ...................................0021-5
Figure 7. Removal of Buffer Assembly and Action Spring....................0021-6
Figure 8. Removal of Bolt Catch .............................................................0021-7
Figure 9. Removal of Magazine Catch ....................................................0021-7
Figure 10. Removal of Sear and Selector Lever .......................................0021-8
Figure 11. Removal of Hammer Assembly ...............................................0021-8
Figure 12. Removal of Trigger Assembly .................................................0021-9
Figure 13. Inspection of Buffer Assembly ..............................................0021-10
Figure 14. Inspection of Action Spring ...................................................0021-10
Figure 15. Inspection for Serial Number................................................0021-11
Figure 16. Condemnation Criteria..........................................................0021-11
Figure 17. Installation of Trigger Assembly (M16A2/M16A4/M4) .......0021-12
Figure 18. Installation of Trigger Assembly (M16A3/M4A1)................0021-13
Figure 19. Installation of Hammer Assembly ........................................0021-13
Figure 20. Installation of Sear and Selector Lever................................0021-14
Figure 21. Installation of Magazine Catch.............................................0021-14
Figure 22. Installation of Bolt Catch ......................................................0021-15
Figure 23. Installation of Action Spring and Buffer Assembly.............0021-16
Figure 24. Installation of Pivot Pin Detent ............................................0021-16
Figure 25. Installation of Pivot Pin ........................................................0021-17
Figure 26. Installation of Buttstock Assembly (Rifle) ...........................0021-18
Figure 27. Installation of Buttstock Assembly (Carbine)......................0021-19
Figure 28. Installation of Pistol Grip......................................................0021-20
Figure 29. Use of Thickness Gage...........................................................0021-21
Figure 30. Use of Trigger and Hammer Gage ........................................0021-22
Buttstock Assembly Maintenance ............................................................................................
Figure 1. Removal/Installation of Buttplate ..........................................0022-1
Figure 2. Removal/Installation of Door Assembly .................................0022-2
Figure 3. Disassembly/Assembly of Door Assembly ..............................0022-2
Figure 4. Disassembly/Assembly of Buttstock Assembly (Carbine) .....0022-3
Hammer Assembly Maintenance ..............................................................................................
Figure 1. Disassembly of Hammer Assembly.........................................0023-1
Figure 2. Assembly of Hammer Assembly..............................................0023-2
Trigger Assembly and Trigger Subassembly Maintenance ....................................................
Figure 1. Disassembly of Trigger Assembly ...........................................0024-1
Figure 2. Installation of Disconnector Springs (M16A2/M16A4/M4) ...0024-2
Figure 3. Installation of Trigger Spring .................................................0024-3
Lower Receiver and Receiver Extension Assembly (M16A2) 9349101,
(M16A3) 12012002, (M16A4) 12598102, (M4) 9390011, and
(M4A1) 12972690 Maintenance .............................................................................................
Figure 1. Removal of Trigger Guard.......................................................0025-1
Figure 2. Removal of Lower Receiver Extension (Rifle) ........................0025-2
Figure 3. Removal of Lower Receiver Extension (Carbine) ..................0025-3
Figure 4. Inspection of Components .......................................................0025-4
Figure 5. Stamping Serial Number.........................................................0025-5
Figure 6. Installation of Buffer Retainer (Rifle) ....................................0025-6
Figure 7. Installation of Lower Receiver Extension (Rifle)...................0025-6
vii
WP 0022
WP 0023
WP 0024
WP 0025
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 3 — FIELD MAINTENANCE INSTRUCTIONS (Continued)
Figure 8. Torquing Lower Receiver Extension (Rifle) ...........................0025-7
Figure 9. Installation of Lower Receiver Extension (Carbine) .............0025-8
Figure 10. Installation of Trigger Guard..................................................0025-9
Adapter Rail Cover Assemblies Maintenance..........................................................................
Figure 1. Removal/Installation of Rail Cover.........................................0026-1
Annual Gaging Requirements...................................................................................................
Preparation for Storage or Shipment .......................................................................................
Pre-embarkation Inspection of Material in Units Alerted for
Overseas Movement................................................................................................................
Table 1.
5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine ....0029-5
Illustrated List of Manufactured Items....................................................................................
Figure 1. Front Sight Detent Depressor.................................................0030-2
Figure 2. Front Sight Post Removal and Installation Tool ...................0030-3
Figure 3. Pivot Pin Removal Tool ...........................................................0030-4
Figure 4. Pivot Pin Installation Tool ......................................................0030-5
Figure 5. Slave Pin...................................................................................0030-6
Figure 6. Adapter Bar for M12 Arms Rack ............................................0030-7
Figure 7. Modified Needle Nose Pliers ...................................................0030-8
CHAPTER 4 — AUXILIARY EQUIPMENT MAINTENANCE INSTRUCTIONS
Auxiliary Equipment .................................................................................................................
Lock Plate Maintenance ............................................................................................................
Figure 1. Removing Pistol Grip for Lock Plate Installation..................0032-2
Figure 2. Installing Lock Plate................................................................0032-3
Figure 3. Positioning Pistol Grip with Lock Plate Installed .................0032-3
Figure 4. Securing Pistol Grip with Lock Plate Installed .....................0032-4
Figure 5. Removing Pistol Grip for Lock Plate Removal.......................0032-4
Figure 6. Removing Lock Plate ...............................................................0032-5
Figure 7. Positioning Pistol Grip with Lock Plate Removed.................0032-6
Figure 8. Securing Pistol Grip with Lock Plate Removed.....................0032-6
Top Sling Adapter Maintenance ...............................................................................................
Figure 1. Installing Top Sling Adapter...................................................0033-1
Figure 2. Installing Clamp on Front Sight.............................................0033-2
Figure 3. Attaching Sling to Top Sling Adapter and Clamp .................0033-2
Figure 4. Removing Sling from Clamp and Top Sling Adapter ............0033-3
Figure 5. Removing Clamp from Front Sight.........................................0033-4
Figure 6. Attaching Sling to Top Sling Adapter and Clamp .................0033-4
Figure 7. Removing Top Sling Adapter ..................................................0033-5
Close Quarters Battle Sling Maintenance ...............................................................................
Figure 1. Removing Sling Swivel ............................................................0034-2
Figure 2. Removing Two Spring Pins .....................................................0034-2
Figure 3. Removing Swivel Locking Bar ................................................0034-3
Figure 4. Removing Swivel Mount..........................................................0034-3
Figure 5. Installing Barrel Band.............................................................0034-3
Figure 6. Attaching Lanyard Assembly..................................................0034-4
Figure 7. Attaching Rear Sling Adapter.................................................0034-4
viii
WP 0026
WP 0027
WP 0028
WP 0029
WP 0030
WP 0031
WP 0032
WP 0033
WP 0034
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 4 — AUXILIARY EQUIPMENT MAINTENANCE INSTRUCTIONS (Continued)
Figure 8. Assembling Sling to Rear Sling Adapter................................0034-4
Figure 9. Attaching Sling to Quick Release Swivel ...............................0034-5
Figure 10. Attaching Swivel to Lanyard ..................................................0034-5
Figure 11. Securing Swivel and Lanyard .................................................0034-5
Blank Firing Attachment Maintenance ...................................................................................
Figure 1. Unscrewing Slide .....................................................................0035-1
Figure 2. Placing Blank Firing Attachment...........................................0035-2
Figure 3. Securing Blank Firing Attachment ........................................0035-2
Figure 4. Unscrewing Slide from the Compensator...............................0035-3
Figure 5. Removing Blank Firing Attachment ......................................0035-3
Figure 6. Securing Slide in Blank Firing Attachment ..........................0035-4
M12 Storage Rack Maintenance ...............................................................................................
Figure 1. Installing Adapter Bar on M12 Storage Rack........................0036-2
Figure 2. Fabrication of Locking Bar......................................................0036-5
Carrying Handle Assembly Maintenance ................................................................................
Figure 1. Disassembly of Carrying Handle Assembly ...........................0037-2
Figure 2. Straightening Rear Sight Guards...........................................0037-3
Figure 3. Assembly and Installation of Elevation Knob Assembly ......0037-4
Figure 4. Installation of Rear Sight Assembly.......................................0037-5
Figure 5. Installation of Helical Spring..................................................0037-6
CHAPTER 5 — PARTS INFORMATION
Introduction to Repair Parts and Special Tools List (RPSTL)................................................
Rifle, 5.56mm (M16A2) 9349000; Rifle, 5.56mm (M16A3) 12012000;
Rifle, 5.56mm (M16A4) 12973001; Carbine, 5.56mm (M4) 9390000;
and Carbine, 5.56mm (M4A1) 12972700 Repair Parts List ................................................
Figure 1. Rifle, 5.56mm (M16A2) 9349000; Rifle, 5.56mm
(M16A3) 12012000; Rifle, 5.56mm (M16A4) 12973001;
Carbine, 5.56mm (M4) 9390000; and Carbine, 5.56mm
(M4A1) 12972700 ....................................................................0039-2
Figure 2. Back-up Iron Sight Assembly (M16A3, M16A4,
M4, M4A1) 12996812...............................................................0039-6
Figure 3. Bolt and Bolt Carrier Assembly 13004788.............................0039-8
Figure 4. Breech Assembly Bolt 13004787...........................................0039-10
Figure 5. Key and Bolt Carrier Assembly 8448505 .............................0039-13
Figure 6. Charging Handle Assembly 8448517 ...................................0039-14
Figure 7. Upper Receiver and Barrel Assembly (M16A2) 9349050,
(M16A3, M16A4) 12973010, and (M4, M4A1) 12972680 ....0039-15
Figure 8. Barrel Assembly (M16A2) 9349124, Barrel Assembly
(M16A3, M16A4) 12598107, Replacement Barrel
and Front Sight Assembly (M4) 9390007, and Replacement
Barrel and Front Sight Assembly (M4A1) 12991851 ..........0039-20
Figure 9. Upper Handguard Assembly (M16A3, M16A4) 12973021 ..0039-23
Figure 10. Barrel Stop Assembly (M16A3, M16A4) 12973139 .............0039-24
Figure 11. Upper Handguard Assembly (M4, M4A1) 12973096...........0039-25
ix
WP 0035
WP 0036
WP 0037
WP 0038
WP 0039
TM 9-1005-319-23&P
TABLE OF CONTENTS - Continued
WP Sequence No.
Page No.
CHAPTER 5 — PARTS INFORMATION (Continued)
Figure 12. Upper Receiver Assembly (M16A2) 9349062, (M16A3,
M16A4) 12973011, and (M4, M4A1) 12972675....................0039-26
Figure 13. Forward Assist Assembly 9349086 .......................................0039-29
Figure 14. Rear Sight Assembly (M16A2) 9349072 and
(M16A3, M16A4, M4, M4A1) 12951026 ...............................0039-30
Figure 15. Lower Receiver and Buttstock Assembly (M16A2)
9349100, (M16A3) 12012001, (M16A4) 12598101,
(M4) 9390011, and (M4A1) 12972690...................................0039-33
Figure 16. Buttstock Assembly (M16A2, M16A3, M16A4) 9349119
and (M4, M4A1) 12012082 ....................................................0039-40
Figure 17. Hammer Assembly (M16A2, M16A4) 9349106,
(M4) 9390032, and (M16A3, M4A1) 8448610.......................0039-44
Figure 18. Trigger Assembly (M16A2, M16A4) 9349115, (M16A3)
8448591, (M4) 12972697, and (M4A1) 12972698.................0039-46
Figure 19. Trigger Subassembly (M16A2, M16A4) 9392518
and (M4) 12972696 ................................................................0039-48
Figure 20. Lower Receiver and Receiver Extension Assembly
(M16A2) 9349101, (M16A3) 12012002, (M16A4)
12598102, (M4) 9390011, and (M4A1) 12972690.................0039-50
Figure 21. M16A3, M16A4, M4, and M4A1 Adapter Rail
Cover Assemblies ...................................................................0039-54
Figure 22. Carrying Handle Assembly (M16A3, M16A4,
M4, M4A1) 12951011.............................................................0039-56
Figure 23. Special Tools...........................................................................0039-58
National Stock Number Index ..................................................................................................
Part Number Index ....................................................................................................................
CHAPTER 6 — SUPPORTING INFORMATION
References...................................................................................................................................
Maintenance Allocation Chart (MAC) Introduction................................................................
Maintenance Allocation Chart (MAC) ......................................................................................
Table 1.
MAC for M16 Series Rifles and M4 Series Carbines.............0044-1
Table 2.
Tools and Test Equipment for M16 Series Rifles and
M4 Series Carbines..................................................................0044-4
Table 3.
Remarks for M16 Series Rifles and M4 Series Carbines ......0044-4
Expendable and Durable Items List.........................................................................................
Table 1.
Expendable and Durable Items List.......................................0045-1
Index
x
WP 0040
WP 0041
WP 0042
WP 0043
WP 0044
WP 0045
TM 9-1005-319-23&P
HOW TO USE THIS MANUAL
Read this manual carefully before performing required maintenance. Inspection/Maintenance and Repair
procedures will be found in this manual.
General
1.
All references are to work packages. Reference to maintenance procedures is to the work package
where the repair appears.
2.
Illustrations for the maintenance procedures show only the parts affected by the operation being
performed.
3.
Whenever the male gender is mentioned in the manual (i.e., crewman and repairman), it also pertains
to the female gender.
4.
When a procedure is common to M16A2, M16A3, and M16A4 rifles and M4/M4A1 carbine, only the
carbine will be shown. If a procedure is not common to all weapons, the procedure will be
appropriately illustrated.
Indexes
This manual is organized with several useful indexes as follows:
1.
Table of Contents. The table of contents lists all work packages, figures, and tables with page
references.
2.
Nomenclature Cross-Reference List. This list provides common and official nomenclature for
parts.
3.
Malfunction/Symptom Index. This index is located just before the troubleshooting table and lists
possible malfunctions in alphabetical order. Pages of the troubleshooting table are referenced.
4.
Alphabetical Index. This index is located at the end of the manual and is an extensive subject index.
Page references are provided.
Maintenance Procedures
There is one maintenance chapter for Field maintenance procedures. Air Force Only: Air Force Specialty
Code 3POXXB, Special Experience Identifier (SEI) 312 or civilian equivalent, and gunsmith are the only
personnel authorized to perform maintenance procedures contained in this manual.
Each maintenance task has an initial setup containing a list of the following things that will be needed to do
the maintenance task:
1.
Tools and Special Tools. For standard and special tools, see WP 0039 and WP 0044. Army users
will use the Tool Set, Gage Set, and/or Shop Set listed in the initial setup.
2.
Materials/Parts. Expendable materials and 100 percent replaceable parts are listed. Each material
or part is followed by a part number or work package reference.
3.
References. Other publications containing necessary information are listed.
4.
Equipment Condition. Conditions to be met before starting the procedure are listed.
xi/xii blank
TM 9-1005-319-23&P
CHAPTER 1
GENERAL INFORMATION,
EQUIPMENT DESCRIPTION,
AND THEORY OF OPERATION
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
0001
FIELD MAINTENANCE
GENERAL INFORMATION
F R O N T S I G H T A S S E M B L Y
R E A R S I G H T A S S E M B L Y
C H A R G I N G
H A N D G U A R D
H A N D L E
E J E C T I O N
P O R T C O V E R
B A Y O N E T L U G
S L I N G
F O R W A R D
T R I G G E R
A S S I S T A S S E M B L Y
L O W E R R E C E I V E R A N D
B U T T S T O C K A S S E M B L Y
M A G A Z I N E R E L E A S E B U T T O N
R I G H T
S I D E
"S Q U A R E " F R O N T
S I G H T P O S T
U P
B O L T
C A T C H
F R O N T S I G H T
C O M P E N S A T O R
B U T T S T O C K
S L I P R I N G
M A G A Z I N E
L E F T
R I F L E G R I P
S I D E
Figure 1. External View of 5.56mm Rifle, M16A2.
0001-1
S E L E C T O R L E V E R
1 v s 0 0 1
TM 9-1005-319-23&P
0001
F R O N T S I G H T A S S E M B L Y
B A C K -U P I R O N
C H A R G I N G
S I G H T
M 5 A D A P T E R R A I L S Y S T E M
H A N D L E
E J E C T I O N
P O R T C O V E R
F O R W A R D
S L I N G
T R I G G E R
A S S I S T A S S E M B L Y
L O W E R R E C E I V E R A N D
B U T T S T O C K A S S E M B L Y
R I G H T
B A Y O N E T L U G
M A G A Z I N E R E L E A S E B U T T O N
S I D E
"S Q U A R E " F R O N T
S I G H T P O S T
U P
B O L T
C A T C H
F R O N T S I G H T
C O M P E N S A T O R
B U T T S T O C K
S L I P R I N G
M A G A Z I N E
L E F T
S E L E C T O R
S I D E
Figure 2. External View of 5.56mm Rifle, M16A3 and M16A4.
0001-2
L E V E R
R I F L E G R I P
1 v s 0 0 2
TM 9-1005-319-23&P
0001
M 4 A D A P T E R
R A I L S Y S T E M
B A C K -U P
I R O N S I G H T
F R O N T S I G H T A S S E M B L Y
S P E N T B R A S S
D E F L E C T O R
C H A R G I N G
H A N D L E
E J E C T I O N
P O R T C O V E R
F O R W A R D A S S I S T
A S S E M B L Y
M A G A Z I N E
T R I G G E R
B A Y O N E T
L U G
S L I N G
S W I V E L
M A G A Z I N E R E L E A S E B U T T O N
R I G H T
S I D E
"S Q U A R E " F R O N T
S I G H T P O S T
B O L T
C A T C H
S L I P R I N G
C O M P E N S A T O R
M 4 A 1
L O C K -R E L E A S E
L E V E R
S E M I
S E M I
S A F E
A D J U S T A B L E
B U T T S T O C K
A U T O
S A F E
M 4
R I F L E
G R I P
B U R S T
L E F T
S L I N G
S I D E
Figure 3. External View of 5.56mm Carbine, M4/M4A1.
0001-3
S E L E C T O R
L E V E R
1 v s 0 0 3
TM 9-1005-319-23&P
0001
SCOPE
Type of Manual
Field maintenance manual.
Model Numbers and Equipment Names
M16A2, M16A3, and M16A4 Rifles and M4 and M4A1 Carbines.
Purpose of Equipment
The purpose of the rifles and carbines is to provide personnel with an offensive/defensive capability to
engage targets with small arms fire.
MAINTENANCE FORMS, RECORDS, AND REPORTS
(1) (A) Department of the Army forms and procedures used for equipment maintenance will be those
prescribed by DA PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual.
(2) (F) Maintenance forms and records used by Air Force personnel are prescribed in AFI 21-101, the
applicable TO-00-20 Series, AFI 36-2226, and TO 11W-1-10.
(3) (N) Navy users should refer to their service peculiar directives to determine applicable maintenance
forms and records to be used.
REPORTING EQUIPMENT IMPROVEMENT RECOMMENDATIONS (EIR)
If your M16 series rifle or M4 series carbine needs improvement, let us know. Send us an EIR. You, the
user, are the only one who can tell us what you don't like about your equipment. Let us know why you don't
like the design or performance. If you have Internet access, the easiest and fastest way to report problems
or suggestions is to go to https://aeps.ria.army.mil/aepspublic.cfm (scroll down and choose the "Submit
Quality Deficiency Report" bar). The Internet form lets you choose to submit an Equipment Improvement
Recommendation (EIR), a Product Quality Deficiency Report (PQDR), or a Warranty Claim Action (WCA).
You may also submit your information using an SF 368 (Product Quality Deficiency Report). You can send
your SF 368 via e-mail, regular mail, or facsimile using the addresses/facsimile numbers specified in DA
PAM 750-8, The Army Maintenance Management System (TAMMS) Users Manual.
Air Force users submit Quality Deficiency Report (QDR) in accordance with Technical Order (TO) 00-35D54, Technical Manual, USAF, Materiel Deficiency Reporting and Investigating System, to: WR-ALC/LEET,
Robins AFB, GA 31098-1640.
Navy users submit Quality Deficiency Report (QDR) to: Commander, Code 4081, Bldg. 2521, NAVSURF
WARCENDIV, 300 Hwy 361, Crane, IN 47522-5001.
We will send you a reply.
0001-4
TM 9-1005-319-23&P
0001
CORROSION PREVENTION AND CONTROL (CPC)
Corrosion Prevention and Control (CPC) of Army materiel is a continuing concern. It is important that any
corrosion problems with this item be reported so that the problem can be corrected and improvements can be
made to prevent the problem in future items.
While corrosion is typically associated with rusting of metals, it can also include deterioration of other
materials such as rubber and plastic. Unusual cracking, softening, swelling, or breaking of these materials
may be a corrosion problem.
If a corrosion problem is identified, it can be reported using SF 368, Product Quality Deficiency Report. Use
of key words such as "corrosion", "rust", "deterioration", or "cracking" will ensure that the information is
identified as a CPC problem.
Army users submit SF 368, Product Quality Deficiency Report, to:
ATTN: AMSRD-AAR-QEW-A
TACOM-ARDEC
1 Rock Island Arsenal
Rock Island, IL 61299-7300
Fax: DSN 793-6653, Commercial (309) 782-6653
E-Mail: [email protected]
Air Force users submit Quality Deficiency Report (QDR) in accordance with TO 00-35D-54, Technical
Manual, USAF, Materiel Deficiency Reporting and Investigating System, located at site
https://spires.wpafb.af.mil/sindex.cfm.
Navy users submit Quality Deficiency Report (QDR) to:
Commander, Code 4081, Bldg. 2521
NAVSURF WARCENDIV, 300 Hwy 361
Crane, IN 47522-5001
DESTRUCTION OF ARMY MATERIEL TO PREVENT ENEMY USE
Refer to TM 750-244-7.
PREPARATION FOR STORAGE OR SHIPMENT
See WP 0028.
Air Force users refer to Special Packaging Instruction (SPI) 00-856-6885.
0001-5
TM 9-1005-319-23&P
NOMENCLATURE CROSS-REFERENCE LIST
Common Name
Official Nomenclature
Action Spring
Automatic Sear
Ball Bearing
Bolt Assembly
Bolt Catch Spring
Bolt Carrier Key Tool
Burst Disconnector
Cam Clutch Spring
Carbine
Charging Handle Assembly
Disconnector Spring
Ejector Spring
Extractor Spring Assembly
Hammer Spring
Lower Receiver Extension
Magazine
Magazine Catch Spring
Peel Washer
Pistol Grip
Pivot Pin Detent
Rifle
Rifle Barrel Assembly
Selector Lever
Semiautomatic Disconnector
Sling
Trigger Spring
Compression Helical Spring
Sear
Bearing Ball
Breech Assembly Bolt
Compression Helical Spring
Machine Key
Lock-Release Lever
Helical Spring
M4/M4A1 Carbine
Handle Assembly
Compression Helical Spring
Helical Spring
Spring Assembly
Torsion Helical Spring
Spring Receiver Holder
Cartridge Magazine
Compression Helical Spring
Shim
Rifle Grip
Headless Straight Pin
Rifle, 5.56mm, M16A2/M16A3/M16A4
Barrel Assembly
Fire Control Selector
Lock-Release Lever
Small Arms Sling
Torsion Helical Spring
LIST OF ABBREVIATIONS/ACRONYMS
Abbreviation/Acronym
AFI
BUIS
CLP
CPC
EIR
fps
in.
lb
mps
PQDR
psi
QDR
RBC
rds/m
SDR
SF
SPI
TO
Air Force Instruction
Back-up iron sight
Cleaner, lubricant, and preservative
Corrosion Prevention and Control
Equipment Improvement Recommendation
feet per second
inch
pound
meters per second
Product Quality Deficiency Report
pounds per square inch
Quality Deficiency Report
Rifle bore cleaning compound
rounds per minute
Supply Discrepancy Report
Standard Form
Special Packaging Instruction
Technical Order
0001-6
0001
TM 9-1005-319-23&P
0001
QUALITY OF MATERIAL
Material used for replacement, repair, or modification must meet the requirements of this TM 9-1005-31923&P. If quality of material requirements is not stated in this TM 9-1005-319-23&P, the material must
meet the requirements of the drawings, standards, specifications, or approved engineering change proposals
applicable to the subject equipment.
SUPPORTING INFORMATION FOR REPAIR PARTS, SPECIAL TOOLS, TMDE, AND SUPPORT EQUIPMENT
Common Tools and Equipment
For authorized common tools and equipment, refer to the Modified Table of Organization and Equipment
(MTOE); CTA 50-970, Expendable/Durable Items (Except: Medical, Class V, Repair Parts, and Heraldic
Items); CTA 50-909, Field and Garrison Furnishings and Equipment; or CTA 8-100, Army Medical
Department Expendable/Durable Items, as applicable to your unit.
Air Force users should maintain the following common tools:
Ball-peen hammer
Combination wrench
Flat file
Flat-tip screwdriver
Hammer
Machinist's vise
Needle nose pliers
Punch
Retaining ring pliers
Socket wrench handle and socket head screw socket wrench
Solid center punch
Torque wrench
Trigger pull test fixture rod and weights
Tweezers/round nose pliers
Vise jaw caps
3-ounce soft-brass hammer
1/16-inch drive pin punch
5/64-inch drive pin punch
3/32-inch drive pin punch
1/8-inch drive pin punch
8-inch adjustable wrench (2)
Special Tools, TMDE, and Support Equipment
Special tools required for field maintenance are listed in WP 0039 and WP 0044. Fabricated tools are listed
and illustrated in WP 0030.
Repair Parts
Repair parts are listed and illustrated in the parts information work package WP 0039 of this manual.
END OF WORK PACKAGE
0001-7/8 blank
TM 9-1005-319-23&P
0002
FIELD MAINTENANCE
EQUIPMENT DESCRIPTION AND DATA
EQUIPMENT CHARACTERISTICS, CAPABILITIES, AND FEATURES
Characteristics
The M16 series rifles and M4 series carbines are lightweight weapons. They are air-cooled, gas-operated,
and magazine-fed. They have a semiautomatic, burst fire capacity, or full automatic fire.
Capabilities and Features
The rifles and carbines provide personnel with an offensive/defensive capability to engage targets with direct
small arms fire.
The receivers are made of light-weight aluminum alloys; however, the safety, durability, and function of the
rifles/carbines are in no way reduced. The portability and logistical values are greatly increased,
particularly when air transport is used.
The bolt locking action is one of the mechanical features of the rifle/carbine. The bolt assembly and barrel
extension contain locking lugs which engage and lock the bolt assembly firmly in the barrel extension. The
initial force of the explosion of the cartridge is absorbed by the barrel, barrel extension, and bolt assembly.
The trigger guard is easily adaptable to winter operations. A spring-loaded retaining pin is depressed to
allow ready access to the trigger when wearing arctic mittens.
The ejection port cover prevents dirt or sand from getting into the ejection port. The ejection port cover must
be closed during periods when firing is not anticipated. It opens automatically with the forward or rearward
movement of the bolt carrier assembly.
0002-1
TM 9-1005-319-23&P
0002
LOCATION AND DESCRIPTION OF MAJOR COMPONENTS
1
2
3
1
2
4
7
5
6
8
M 1 6 A 2
7
1
2
4
5
6
9
M 4 /M 4 A 1
4
5
6
M 1 6 A 3 /M 1 6 A 4
1 v s 0 0 4
Figure 1. Major Components of Rifles and Carbines.
0002-2
TM 9-1005-319-23&P
0002
Charging Handle Assembly (1)
This assembly provides a means of charging the weapon.
Bolt Carrier Assembly (2)
The bolt carrier assembly carries bolt assembly to chamber and fires the weapon. It contains the firing pin,
cartridge extractor, bolt assembly, cartridge ejector, and bolt cam pin.
M16A2 Upper Receiver and Barrel Assembly (3)
The upper receiver contains rear sight assembly, ejection port, ejection port cover, and a housing for the key
and bolt carrier assembly and bolt assembly. The rifle barrel assembly is air-cooled, contains compensator
and front sight assembly, and holds the two handguard assemblies and the sling swivel.
Magazine (4)
The magazine has a 30 cartridge capacity.
Lower Receiver and Buttstock Assembly (5)
The lower receiver contains the trigger assembly, sear, hammer assembly, selector lever, rifle grip, bolt
catch, and buttstock assembly. The buttstock assembly houses the action spring, buffer assembly, and
extension assembly.
Sling (6)
The sling is adjustable and provides a means to carry the weapon.
M16A3/M16A4 and M4/M4A1 Back-up Iron Sight (7)
The back-up iron sight contains rear sight assembly.
M4/M4A1 Upper Receiver and Barrel Assembly (8)
The upper receiver contains ejection port, ejection port cover, and a housing for the key and bolt carrier
assembly and bolt assembly. The carbine barrel assembly is air-cooled, contains compensator and front
sight assembly, and holds the two adapter rail assemblies (upper and lower) and the sling swivel with side
mount.
M16A3 and M16A4 Upper Receiver and Barrel Assembly (9)
The upper receiver contains ejection port, ejection port cover, and a housing for the key and bolt carrier
assembly and bolt assembly. The rifle barrel assembly is air-cooled, contains compensator and front sight
assembly, and holds the two adapter rail assemblies (upper and lower) and the sling swivel.
0002-3
TM 9-1005-319-23&P
0002
EQUIPMENT DATA
PHYSICAL CHARACTERISTICS
Weight:
Carbine, M4, without magazine and sling ............................................................................... 6.44 lb (2.92 kg)
Carbine, M4A1, without magazine and sling .......................................................................... 7.81 lb (3.54 kg)
Rifle, M16A2, without magazine and sling.............................................................................. 7.50 lb (3.40 kg)
Rifle, M16A3, M16A4, without magazine and sling................................................................7.81 lb (3.54 kg)
Sling, adjustable ........................................................................................................................0.25 lb (0.11 kg)
Empty magazine ........................................................................................................................0.25 lb (0.11 kg)
Loaded magazine .......................................................................................................................1.06 lb (0.48 kg)
Carbine, M4, w/sling and loaded magazine ............................................................................. 7.75 lb (3.51 kg)
Carbine, M4A1, w/sling and loaded magazine.........................................................................8.63 lb (3.91 kg)
Rifle, M16A2, w/sling and loaded magazine ............................................................................ 8.81 lb (4.00 kg)
Rifle, M16A3, M16A4, w/sling and loaded magazine ..............................................................9.13 lb (4.14 kg)
Bayonet-Knife, M7.....................................................................................................................0.66 lb (0.30 kg)
Scabbard, M10 ...........................................................................................................................0.31 lb (0.14 kg)
Length:
Carbine with compensator, buttstock extended .................................................................. 33.0 in. (83.82 cm)
Carbine with compensator, buttstock closed ..................................................................... 29.75 in. (75.57 cm)
Rifle with compensator...................................................................................................... 39.63 in. (100.66 cm)
Barrel (Carbine)..................................................................................................................... 14.5 in. (36.83 cm)
Barrel (Rifle) ............................................................................................................................... 20 in. (50.8 cm)
Barrel with compensator (Carbines) .................................................................................... 15.5 in. (39.37 cm)
Barrel with compensator (Rifles)............................................................................................. 21 in. (53.34 cm)
Mechanical Features:
Rifling ........................................................................... Right-hand twist 6 grooves, 1 turn in 7 in. (17.78 cm)
Method of operation.............................................................................................................................Direct gas
Type of breech mechanism .............................................................................................................Rotating bolt
Method of feeding ................................................................................................................................ Magazine
Cooling............................................................................................................................................................. Air
Trigger pull (M16A2, M16A4, & M4) .................................................................. 5.5 to 9.5 lb (2.49 to 4.31 kg)
Trigger pull (M16A3 & M4A1)............................................................................. 5.5 to 8.5 lb (2.49 to 3.86 kg)
Ammunition:
Caliber ..................................................................................................................................................... 5.56mm
Type ................................................................................................. Ball, blank, dummy, tracer, and frangible
FIRING CHARACTERISTICS
Muzzle velocity (Carbines) (approximate) ......................................................................... 2,970 fps (905 mps)
Muzzle velocity (Rifles) (approximate) ............................................................................... 3,100 fps (945 mps)
Chamber pressure .......................................................................................................52,000 psi (358,540 kPa)
Cyclic rate of fire (Carbines) (approximate)............................................................................700 to 970 rds/m
Cyclic rate of fire (Rifles) (approximate) .................................................................................700 to 900 rds/m
0002-4
TM 9-1005-319-23&P
0002
Maximum rate of fire:
Semiautomatic................................................................................................................................. 45 rds/m
Burst ................................................................................................................................................ 90 rds/m
Sustained rate of fire .............................................................................................................12 to 15 rds/m
Maximum range........................................................................................... 11,814 ft (approximately 3,600 m)
Maximum effective range:
Individual/point targets (M16A3/M16A4 Rifles & Carbines)........................................... 1,641 ft (500 m)
Individual/point targets (M16A2 Rifle) ............................................................................. 1,806 ft (550 m)
Area targets (M16A3/M16A4 Rifles & Carbines).............................................................. 1,950 ft (594 m)
Area targets (M16A2 Rifle)................................................................................................. 2,625 ft (800 m)
END OF WORK PACKAGE
0002-5/6 blank
TM 9-1005-319-23&P
0003
FIELD MAINTENANCE
THEORY OF OPERATION
GENERAL
The 5.56mm M16A2, M16A3, M16A4 rifle and the M4/M4A1 carbine is gas-operated. It fires in the
semiautomatic, full automatic, or burst mode. The weapon has positive locking of the bolt. The firing pin is
part of the bolt carrier assembly and cannot strike the primer until the bolt assembly is fully locked.
0003-1
TM 9-1005-319-23&P
0003
PRINCIPLES OF OPERATION
1
2
3
1
2
4
7
5
6
8
M 1 6 A 2
7
1
2
5
6
9
5
4
M 4 /M 4 A 1
4
6
M 1 6 A 3 /M 1 6 A 4
1 v s 0 0 5
Figure 1. Operation of Rifles and Carbines.
0003-2
TM 9-1005-319-23&P
0003
Charging Handle Assembly (1)
This assembly provides initial charging of the weapon. The handle latch locks the charging handle assembly
in the forward position during sustained fire to prevent injury to the operator.
Bolt Carrier Assembly (2)
This assembly provides stripping, chambering, locking, firing, extraction, and ejection of cartridges using the
drive springs and projectile propelling gases for power.
M16A2 Upper Receiver and Barrel Assembly (3)
The upper receiver provides support for the bolt carrier assembly. The barrel chambers the cartridge for
firing and directs the projectile.
Magazine (4)
The magazine holds cartridges ready for feeding and provides a guide for positioning cartridges for stripping.
It provides quick reload capabilities for sustained firing.
Lower Receiver and Buttstock Assembly (5)
This assembly provides firing control for the rifle and carbine. Storage for basic cleaning materials is
provided in the M16A2, M16A3, and M16A4 rifles.
Sling (6)
The sling provides the means for carrying the weapon.
Back-up Iron Sight (BUIS) (7)
The BUIS can be used to sight the weapon when other means are unavailable.
M4/M4A1 Upper Receiver and Barrel Assembly (8)
The upper receiver provides support for the bolt carrier assembly. The barrel chambers the cartridge for
firing and directs the projectile. The upper receiver contains an integral mounting rail to which various
accessories attach.
M16A3 and M16A4 Upper Receiver and Barrel Assembly (9)
The upper receiver provides support for the bolt carrier assembly. The barrel chambers the cartridge for
firing and directs the projectile. The upper receiver contains an integral mounting rail to which various
accessories attach.
END OF WORK PACKAGE
0003-3/4 blank
TM 9-1005-319-23&P
CHAPTER 2
FIELD
TROUBLESHOOTING PROCEDURES
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
0004
FIELD MAINTENANCE
TROUBLESHOOTING INDEX
GENERAL
Field level troubleshooting information is provided for locating and correcting most of the operating troubles
which may develop in the M16A2, M16A3, M16A4 rifle, M4/M4A1 carbine. Each malfunction for the
individual part or assembly is followed by a list of tests or inspections which will help you to determine the
corrective actions in the order listed.
This manual cannot list all malfunctions that may occur, or all tests or inspections and corrective actions. If
a malfunction is not listed or is not corrected by listed corrective actions, see individual repair sections in the
maintenance procedures for each major assembly.
See the troubleshooting table (WP 0005) for malfunctions, tests, and corrective actions. The symptom index
is provided for a quick reference to the malfunctions covered in the table.
MALFUNCTION/SYMPTOM INDEX
Work Package - Page
Symptom
Bolt assembly fails to lock to rear after firing last round.............................................................
Failure of magazine to lock in rifle/carbine...................................................................................
Failure to chamber..........................................................................................................................
Failure to cock .................................................................................................................................
Failure to cycle with selector lever set on AUTO (M16A3 and M4A1 only)................................
Failure to cycle with selector lever set on BURST (M16A2/M16A4 and M4 only) .....................
Failure to eject.................................................................................................................................
Failure to extract.............................................................................................................................
Failure to feed .................................................................................................................................
Failure to fire...................................................................................................................................
Failure to lock..................................................................................................................................
Failure to unlock .............................................................................................................................
Fires two rounds with one pull of trigger with selector lever set on SEMI (double firing)........
Fires with selector lever on SAFE or when trigger is released with selector lever on SEMI ....
Hammer pin "walks" .......................................................................................................................
Rifle/carbine cannot be zeroed........................................................................................................
Short recoil ......................................................................................................................................
END OF WORK PACKAGE
0004-1/2 blank
0005-21
0005-1
0005-3
0005-10
0005-18
0005-16
0005-9
0005-8
0005-2
0005-5
0005-4
0005-8
0005-18
0005-20
0005-20
0005-14
0005-12
TM 9-1005-319-23&P
FIELD MAINTENANCE
TROUBLESHOOTING PROCEDURES
M16 SERIES RIFLE/M4 SERIES CARBINE
INITIAL SETUP:
Tools and Special Tools
Shop Set, Small Arms: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Materials/Parts
Bore small arms cleaning brush (WP 0045, item 4)
Carbon removing compound (WP 0045, item 8)
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Gloves (WP 0045, item 17)
Pipe cleaner (WP 0045, item 11)
Reflector tool (WP 0039, Figure 23, item 3)
References
TM 9-1005-319-10
WP 0009
WP 0011
WP 0012
WP 0013
WP 0015
WP 0016
WP 0019
WP 0021
WP 0023
WP 0024
M16 SERIES RIFLE/M4 SERIES CARBINE
Table 1. Troubleshooting Procedures.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
1. FAILURE OF MAGAZINE TO LOCK IN RIFLE/CARBINE.
Step 1. Inspect for dirty or corroded magazine catch (1).
Disassemble and clean (WP 0021).
0005-1
0005
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
1. FAILURE OF MAGAZINE TO LOCK IN RIFLE/CARBINE - Continued.
Step 2. Inspect for defective magazine catch spring (2).
Replace magazine catch spring (WP 0021).
Step 3. Inspect for worn or broken magazine catch (1).
Replace magazine catch (WP 0021).
2
1
1 v s 0 0 6
Figure 1. Magazine Catch Inspection.
2. FAILURE TO FEED.
Step 1. Inspect for weak or broken magazine catch spring (2).
Replace magazine catch spring (WP 0021).
Step 2. Inspect for defective magazine catch (1).
Replace magazine catch (WP 0021).
Step 3. Determine if magazine catch (1) is out of adjustment (will not retain magazine).
Refer to TM 9-1005-319-10.
Step 4. Check for short recoil.
See Malfunction 10.
0005-2
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
2
1
1 v s 0 0 6
Figure 2. Magazine Catch and Spring Inspection.
3. FAILURE TO CHAMBER.
Step 1. Inspect for weak or broken action spring (3). RIFLE ONLY: Free length should be 11 3/4
in. (29.85 cm) minimum to 13 1/2 in. (34.29 cm) maximum. CARBINE ONLY: Free length
should be 10 1/16 in. (25.56 cm) minimum to 11 1/4 in. (28.58 cm) maximum.
Replace action spring (WP 0021).
3
1 v s 0 0 7
Figure 3. Action Spring.
Step 2. Check for short recoil.
See Malfunction 10.
0005-3
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
4. FAILURE TO LOCK.
Step 1. Inspect for missing bolt cam pin (4).
Replace bolt cam pin (WP 0011).
Step 2. Inspect for damaged bolt carrier key (5).
Repair slightly dented bolt carrier key. Replace more seriously damaged bolt carrier key
(WP 0013).
Step 3. Inspect for loose screws (6) on bolt carrier key (5).
a. Disassemble and repair (WP 0013).
b. Reassemble using new screws.
4
5
6
1 v s 0 0 8
Figure 4. Bolt Carrier Assembly Inspection.
Step 4. Inspect for improperly assembled extractor spring assembly (7).
Assemble correctly (WP 0012).
7
1 v s 0 0 9
Figure 5. Extractor Spring Assembly Inspection.
0005-4
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 5. Inspect for bent gas tube (8).
a. Adjust to original configuration by bending gas tube in area of handguards.
b. Replace gas tube and check alignment (WP 0015).
8
1 v s 0 1 0
Figure 6. Gas Tube.
Step 6. Inspect for weak or broken action spring (3). RIFLE ONLY: Free length should be 11 3/4
in. (29.85 cm) minimum to 13 1/2 in. (34.29 cm) maximum. CARBINE ONLY: Free length
should be 10 1/16 in. (25.56 cm) minimum to 11 1/4 in. (28.58 cm) maximum.
Replace action spring (WP 0021).
3
1 v s 0 0 7
Figure 7. Action Spring Inspection.
Step 7. Check for short recoil.
See Malfunction 10.
5. FAILURE TO FIRE.
Step 1. Inspect for carbon buildup in firing pin recess inside bolt assembly.
Remove cartridge extractor and clean recess with pipe cleaner (WP 0045, item 11); see
TM 9-1005-319-10.
0005-5
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
5. FAILURE TO FIRE - Continued.
Step 2. Inspect for broken hammer (10).
Replace hammer (WP 0021 and WP 0023).
Step 3. Inspect for broken hammer spring (9).
Replace hammer spring (WP 0021 and WP 0023).
Step 4. Check for improper assembly of hammer spring (9).
Assemble properly (WP 0023).
Step 5. (M16A2, M16A4, and M4 Only) Determine if burst cam (12) and/or burst cam spring (11)
is frozen or improperly assembled.
Disassemble, clean, lubricate, and reassemble correctly (WP 0023).
1 1
9
1 0
1 2
9
M 1 6 A 2 , M 1 6 A 4 , a n d M 4 O n ly
1 0
M 1 6 A 3 a n d M 4 A 1 O n ly
1 v s 0 1 1
Figure 8. Hammer and Burst Cam Inspection.
0005-6
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 6. Inspect for broken, defective, or missing firing pin retaining pin (13).
Replace firing pin retaining pin (WP 0011).
1 3
1 v s 0 1 2
Figure 9. Firing Pin Retaining Pin Inspection.
Step 7. Determine if selector lever (14) is frozen on SAFE position.
Disassemble and clean (WP 0021).
Step 8. Inspect for broken firing pin (15) or for firing pin that does not meet gage protrusion
requirement.
Replace firing pin (WP 0011).
S E M I
1 5
1 4
S A F E
1 v s 0 1 3
Figure 10. Selector Lever and Firing Pin Inspection.
0005-7
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
6. FAILURE TO UNLOCK.
Step 1. Inspect for burred locking lugs on bolt assembly (16).
Remove burrs.
Step 2. Inspect for burred lugs (17) on barrel extension.
Remove burrs.
1 6
1 7
1 v s 0 1 4
Figure 11. Locking Lugs Inspection.
Step 3. Check for short recoil.
See Malfunction 10.
7. FAILURE TO EXTRACT.
Step 1. Inspect for defective extractor pin (18), cartridge extractor (19), and/or extractor spring
assembly (7).
Replace extractor pin, cartridge extractor, and/or extractor spring assembly (WP 0012).
1 8
7
1 9
1 v s 0 1 5
Figure 12. Cartridge Extractor Inspection.
0005-8
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 2. Inspect badly pitted chamber with reflector tool (WP 0039, Figure 23, item 3).
Replace barrel assembly if chamber is badly pitted (WP 0015).
Step 3. Check for short recoil.
See Malfunction 10.
8. FAILURE TO EJECT.
Step 1. Inspect for broken cartridge ejector (22).
Replace cartridge ejector (WP 0012).
Step 2. Determine if cartridge ejector (22) is stuck in bolt body (20).
Disassemble and clean (WP 0012).
Step 3. Inspect for weak or broken ejector spring (21).
Replace ejector spring (WP 0012).
2 0
2 1
2 2
1 v s 0 1 6
Figure 13. Cartridge Ejector Inspection.
Step 4. Check for short recoil.
See Malfunction 10.
0005-9
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
9. FAILURE TO COCK.
Step 1. Inspect for worn or broken trigger nose (24) or trigger spring (25).
Replace trigger (23) or defective trigger spring (WP 0024).
Step 2. Inspect for worn or broken hammer trigger notch (28).
Replace hammer (10) (WP 0021 and WP 0023).
Step 3. Inspect for worn or broken hammer disconnector hook (27).
Replace hammer (10) (WP 0021 and WP 0023).
Step 4. Inspect for worn or broken automatic sear hook (26).
Replace hammer (10) (WP 0021 and WP 0023).
1 0
2 3
2 4
2 5
2 3
2 5
2 4
2 6
2 6
1 0
2 7
2 8
M 1 6 A 3 a n d M 4 A 1 O n ly
M 1 6 A 2 , M 1 6 A 4 , a n d M 4 O n ly
1 v s 0 1 7
Figure 14. Trigger and Hammer Inspection.
Step 5. (M16A3 and M4A1 have only one disconnector) Inspect for worn or broken
disconnector hooks (29).
Replace defective disconnectors (30) (WP 0021).
Step 6. (M16A3 and M4A1 have only one spring) Inspect for weak, broken, or missing
disconnector springs (34).
Replace disconnector springs (WP 0021).
0005-10
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 7. Inspect for worn, broken, or missing automatic sear (33).
Replace automatic sear (WP 0021).
Step 8. Inspect for weak or broken automatic sear spring (32).
Replace automatic sear (33) (WP 0021).
Step 9. Determine if long leg (31) of automatic sear spring (32) is incorrectly assembled in receiver.
Remove automatic sear (33) and install correctly (WP 0021).
Step 10. (M16A2, M16A4, and M4 only) Determine if burst cam (12) or burst cam spring (11) is
frozen or improperly assembled.
Disassemble, inspect, clean, lubricate, or replace as required (WP 0021).
2 9
3 0
1 1
3 1
3 3
2 9
M 1 6 A 2 /
M 1 6 A 4 /M 4
3 2
1 2
3 0
2 9
3 4
3 0
M 1 6 A 3 /M 4 A 1
1 v s 0 1 8
Figure 15. Disconnector, Automatic Sear, and Burst Cam Inspection.
Step 11. Check for short recoil.
See Malfunction 10.
0005-11
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
10. SHORT RECOIL.
Step 1. Inspect for broken or damaged action spring (3).
Replace action spring (WP 0021).
Step 2. Inspect for unlubricated or dirty action spring (3) and receiver extension.
Clean and lubricate.
3
1 v s 0 0 7
Figure 16. Action Spring Replacement.
Step 3. Inspect for improper gap space or worn, missing, or broken bolt rings (35).
a. Stagger bolt ring gaps (approximately 1/3 turn apart).
b. If worn, broken, or missing, replace bolt rings and stagger gaps (WP 0012).
3 5
1 v s 0 1 9
Figure 17. Bolt Ring Gap Adjustment.
0005-12
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 4. Inspect for carbon build-up or foreign matter in narrow passage of bolt carrier key (5).
Clean with CLP (WP 0045, item 9) and a worn bore brush.
5
1 v s 0 2 0
Figure 18. Bolt Carrier Key Inspection.
Step 5. Inspect for broken or bent gas tube (8).
Adjust by bending in area of handguards or replace gas tube (WP 0015).
Step 6. Determine if gas tube spring pin (37) is missing from front sight (36).
Replace gas tube spring pin (WP 0015).
Step 7. Inspect for partially plugged gas system because of carbon build-up in gas tube (8).
Replace gas tube (WP 0015).
8
3 6
3 7
1 v s 0 2 1
Figure 19. Adjustment of Gas Tube.
0005-13
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
10. SHORT RECOIL - Continued.
WARNING
CARBON REMOVING COMPOUND
Step 8. Inspect for carbon build-up in barrel gas port (38).
Remove carbon build-up by soaking barrel in carbon removing compound (WP 0045, item
8). Use rubber gloves (WP 0045, item 17) with carbon removing compound. Use a bore
small arms cleaning brush (WP 0045, item 4).
3 8
1 v s 0 2 2
Figure 20. Barrel Gas Port Cleaning.
11. RIFLE/CARBINE CANNOT BE ZEROED.
Step 1. Inspect for defective or bent barrel assembly (44) (WP 0016).
Replace barrel assembly (WP 0015).
Step 2. (For windage) Determine if barrel assembly (44) is out of alignment with rear sight (39) on
upper receiver.
Align barrel assembly and upper receiver (WP 0015).
0005-14
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
Step 3. (For elevation) Inspect for defective front sight (40).
Remove front sight post (41), front sight detent (42), and helical spring (43). If damaged,
replace.
Step 4. (For elevation) Inspect for defective rear sight (39).
Repair as required (WP 0019).
3 9
4 1
4 2
4 3
4 0
4 4
Figure 21. Front Sight and Rear Sight Inspection.
0005-15
1 v s 0 2 3
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
12. FAILURE TO CYCLE WITH SELECTOR LEVER SET ON BURST (M16A2/M16A4 AND M4
ONLY).
Step 1. Inspect for broken automatic sear (33) or automatic sear spring (32).
Replace automatic sear (WP 0021).
Step 2. Inspect for faulty selector lever (14).
Replace selector lever (WP 0021).
Step 3. Inspect for broken tooth on burst cam (12).
Replace burst cam (WP 0021).
3 2
1 4
3 3
1 2
M 1 6 A 2 /M 1 6 A 4 a n d M 4
1 v s 0 2 4
Figure 22. Automatic Sear and Selector Lever Inspection.
Step 4. Inspect for broken burst cam spring (11). Burst cam spring should be bent and properly
formed without any sharp edges or corners.
Inspect and replace burst cam spring if required (WP 0023).
Step 5. Determine if bend in burst cam spring (11) is installed backwards (toward outside).
Install burst cam spring properly with bend to inside (WP 0023).
0005-16
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
NOTE
When hammer is rotated back to cocked position, burst cam should rotate to allow
burst disconnector to latch in next notch.
Step 6. Determine if burst cam spring (11) fails to "clutch" and burst cam (12) fails to rotate back
with hammer (10).
Replace burst cam spring. If problem continues, replace hammer and burst cam
(WP 0023).
Step 7. Inspect for broken front hook (29) on burst disconnector (30).
Replace burst disconnector (WP 0021).
1 1
2 9
1 2
1 0
3 0
M 1 6 A 2 /M 1 6 A 4 a n d M 4
1 v s 0 2 5
Figure 23. Burst Disconnector and Burst Cam Inspection.
Step 8. Check for short recoil.
See Malfunction 10.
0005-17
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
13. FAILURE TO CYCLE WITH SELECTOR LEVER SET ON AUTO (M16A3 AND M4A1 ONLY).
Step 1. Inspect for broken automatic sear (33) or automatic sear spring (32).
Replace automatic sear (WP 0021).
Step 2. Inspect for faulty selector lever (14).
Replace selector lever (WP 0021).
1 4
3 2
3 3
1 v s 0 2 6
Figure 24. Selector Lever and Automatic Sear Inspection.
Step 3. Check for short recoil.
See Malfunction 10.
14. FIRES TWO ROUNDS WITH ONE PULL OF TRIGGER WITH SELECTOR LEVER SET ON
SEMI (DOUBLE FIRING).
Step 1. Perform function test (WP 0009).
If any part of function test fails, continue with next step.
Step 2. Inspect for defective semiautomatic disconnector (30).
Replace semiautomatic disconnector (WP 0021).
Step 3. Inspect for worn or broken trigger notch (28) of hammer (10) (searing portion).
Replace hammer (WP 0021).
Step 4. Inspect for worn or broken disconnector hook (27) of hammer (10).
Replace hammer (WP 0021).
0005-18
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
3 0
2 7
2 8
3 0
1 0
1 0
M 1 6 A 2 a n d M 4
M 1 6 A 3 a n d M 4 A 1
1 v s 0 2 7
Figure 25. Semiautomatic Disconnector and Hammer Inspection.
Step 5. Inspect for worn or broken trigger (23) (searing portion).
Replace trigger (WP 0021).
Step 6. Inspect for worn hammer or trigger pin hole.
Gage hammer pin hole (45) and trigger pin hole (46) (WP 0009). If test fails, replace
weapon.
4 5
4 6
4 5
4 6
2 3
M 1 6 A 2 a n d M 4
2 3
M 1 6 A 3 a n d M 4 A 1
1 v s 0 2 8
Figure 26. Trigger and Pin Hole Inspection.
0005-19
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
15. FIRES WITH SELECTOR LEVER ON SAFE OR WHEN TRIGGER IS RELEASED WITH
SELECTOR LEVER ON SEMI.
Step 1. Inspect for defective selector lever (14).
Replace selector lever (WP 0021).
Step 2. Inspect for worn or broken rear portion of trigger (23).
Replace trigger (WP 0021).
2 3
2 3
1 4
1 4
M 1 6 A 3 a n d M 4 A 1
M 1 6 A 2 a n d M 4
1 v s 0 2 9
Figure 27. Selector Lever and Trigger Inspection.
16. HAMMER PIN "WALKS".
Inspect hammer pin (47). Determine if it "walks" or works loose during firing or if hammer pin is
very easy to push out of receiver when hammer is installed.
Replace hammer assembly (WP 0021).
4 7
1 v s 0 3 0
Figure 28. Hammer Pin Inspection.
0005-20
TM 9-1005-319-23&P
0005
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
17. BOLT ASSEMBLY FAILS TO LOCK TO REAR AFTER FIRING LAST ROUND.
Step 1. Inspect magazine follower (50) for wear, breaks, or separation from magazine spring (49).
Replace magazine.
Step 2. Determine if magazine spring (49) is weak or broken.
Replace magazine.
Step 3. Inspect magazine feeder lips (48) for bends or breaks.
Replace magazine.
Step 4. Determine if magazine follower (50) binds during operation.
Replace magazine.
4 9
4 8
5 0
1 v s 0 3 1
Figure 29. Magazine Inspection.
0005-21
TM 9-1005-319-23&P
0005
M16 SERIES RIFLE/M4 SERIES CARBINE - Continued
Table 1. Troubleshooting Procedures - Continued.
MALFUNCTION
TEST OR INSPECTION
CORRECTIVE ACTION
17. BOLT ASSEMBLY FAILS TO LOCK TO REAR AFTER FIRING LAST ROUND - Continued.
Step 5. Inspect for broken bolt catch (51).
Replace bolt catch (WP 0021).
Step 6. Inspect for weak or broken bolt catch spring (52).
Replace bolt catch spring (WP 0021).
Step 7. Inspect for restricted movement of bolt catch (51).
Disassemble and clean.
5 1
5 2
1 v s 0 3 2
Figure 30. Bolt Catch Inspection.
END OF WORK PACKAGE
0005-22
TM 9-1005-319-23&P
CHAPTER 3
FIELD
MAINTENANCE INSTRUCTIONS
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
0006
FIELD MAINTENANCE
SERVICE UPON RECEIPT
GENERAL
When a new or reconditioned weapon is first received, it is the responsibility of the officer-in-charge to
determine whether the weapon has been properly prepared for service by supplying organization and
whether it is in proper condition to perform its mission.
SERVICE UPON RECEIPT OF MATERIEL
Unpacking
WARNING
Before starting an inspection, be sure to clear the weapon. Do not pull the
trigger until the weapon has been cleared. Inspect the chamber to ensure
that it is empty and no ammunition is in position to be chambered.
Remove the weapon and basic issue items from containers. Check for any missing items. Refer to TM
9-1005-319-10.
Checking Unpacked Equipment
Inspect the equipment for damage incurred during shipment. If the equipment has been damaged, report
the damage on SF 361, Transportation Discrepancy Report. Air Force users will submit a Supply
Discrepancy Report (SDR) in accordance with the guidance in Technical Order 00-35D-54.
Check the equipment against the packing slip to see if the shipment is complete. Report all discrepancies in
accordance with applicable service instructions (e.g., for Army instructions, see DA PAM 750-8).
Air Force users submit Quality Deficiency Report (QDR) in accordance with Technical Order 00-35D-54,
Materiel Deficiency Reporting and Investigating System, located at site https://spires.wpafb.af.mil/
sindex.cfm, and with Air Force Joint Manual (AFJMAN) 23-215, Reporting of Supply Discrepancies.
Navy users submit Quality Deficiency Report (QDR) to: Commander, Code 4081, Bldg 2521, NAVSURF
WARCENDIV, 300 Hwy 361, Crane, IN 47522-5001.
Check to see whether the equipment has been modified. Refer to DA PAM 25-30.
Processing Unpacked Equipment
If volatile corrosion inhibitor (VCI) is in barrel, remove and discard. Field-strip weapon and inspect for
missing, damaged, and rusted or corroded parts. Clean and lubricate. Refer to TM 9-1005-319-10.
END OF TASK
0006-1
TM 9-1005-319-23&P
INSTALLATION INSTRUCTIONS
Refer to TM 9-1005-319-10 to assemble weapon and to perform function check. Check the magazine for
positive retention and functioning of bolt catch.
END OF TASK
END OF WORK PACKAGE
0006-2
0006
TM 9-1005-319-23&P
0007
FIELD MAINTENANCE
PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS) INTRODUCTION
GENERAL, EXPLANATION OF COLUMN ENTRIES
GENERAL
a. Preventive Maintenance Checks and Services (PMCS) (WP 0008) must be performed by field
maintenance personnel to be sure the M16 series rifle or M4 series carbine is in good operating condition
and ready for its primary mission.
b. To ensure maximum operational readiness, it is necessary that the rifle/carbine be inspected at
regular intervals so that any defects can be discovered and corrected before serious damage or failure occurs.
EXPLANATION OF COLUMN ENTRIES
a. Item No. Column. Checks and services are numbered in disassembly sequence. This column shall
be used as a source of item numbers for the "TM Number" column on DA Form 5988-E, Equipment
Inspection and Maintenance Worksheet, or DA Form 2404, Equipment Inspection and Maintenance
Worksheet, in recording results of PMCS.
b. Interval Column. This column gives the designated interval when each check is to be performed.
c. Man-Hour Column. This column indicates the amount of time required to perform the check or
service.
d. Item To Be Checked or Serviced Column. This column lists the items to be checked or serviced.
e. Procedure Column. This column contains a brief description of the procedure by which the check
is to be performed. It contains all the information required to accomplish the checks and services.
Information marked "SH" indicates a specific equipment shortcoming and the procedure needed to correct
the shortcoming.
NOTE
For the purpose of this technical manual, the following definition is supplied. This
definition is not intended to apply to any other document.
Shortcoming (SH): A fault that requires maintenance or supply action on a piece of
equipment, but does not render equipment unavailable for use.
f. Equipment Not Ready/Available If: Column. This column contains a brief statement of the
condition (e.g., malfunction, deficiency) that would cause the covered equipment to be unavailable to perform
its assigned mission.
END OF WORK PACKAGE
0007-1/2 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS),
INCLUDING LUBRICATION INSTRUCTIONS
PMCS PROCEDURES, LUBRICATION INSTRUCTIONS
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Abrasive cloth (WP 0045, item 13)
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 10)
Dry cleaning solvent (WP 0045, item 15)
Gloves (WP 0045, item 17)
Rifle bore cleaning compound (RBC) (WP 0045, item 12)
Solid film lubricant (WP 0045, item 20)
Wash pan (WP 0045, item 26)
Weapons lubricating oil (LAW) (WP 0045, item 22)
Weapons lubricating oil (LSA) (WP 0045, item 21)
References
TM 9-1005-319-10
WP 0011
WP 0015
WP 0045
PMCS PROCEDURES
WARNING
Before starting an inspection, be sure to clear weapon. Do not pull trigger
until weapon is cleared. Inspect chamber to ensure that it is empty and no
ammunition is in position to be chambered.
WARNING
Do not keep live ammunition near work area.
0008-1
0008
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
NOTE
An inactive weapon is a weapon which has been stored in an arms room for a period
of 90 days without use. The weapon may or may not have been assigned to an
individual. Inactive weapons shall receive quarterly PMCS unless inspection reveals
more frequent servicing is necessary. Normal cleaning (PMCS) of an inactive weapon
will be performed every 90 days. If corrosion is detected on a weapon prior to the end
of the 90-day period, the PMCS should be performed immediately.
Solid film lubricant (SFL) is the authorized touch up for the M16A2, M16A3, and
M16A4 Rifle and M4/M4A1 Carbine and may be used on up to one third of the
exterior finish of the weapon.
FOR ARMY CONUS USE ONLY AND AIR FORCE TRAINING WEAPONS ONLY:
Solid film lubricant may be used as a touch up without limitation on the upper
receiver and barrel assembly. Units which DO NOT fall under the category of
Divisional Combat Units or rapid deployment type units may have up to 100 percent
of the exterior surface of the upper receiver and barrel assembly protected with SFL.
Prior to application of SFL, the surface must be thoroughly cleaned and inspected for
corrosion and/or damage. If corroded or damaged, the part must be repaired or
replaced prior to application of SFL. Continued use under combat conditions would
result in an unprotected surface when the SFL wears off. This would result in a
large light reflecting surface and accelerated deterioration of the unprotected surface.
Therefore, Divisional Combat Units and units which fall under the definition of
Rapid Deployment type must adhere to the limitation of NOT over one third of their
exterior surface covered by SFL.
When determining mission capability, deadline if it is a deficiency.
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines.
Item
No.
1
Interval
Quarterly
ManHour
Item To Be
Checked or
Serviced
Magazine
(Serviceability
Check)
Procedure
Equipment Not
Ready/Available
If:
a. Check for availability of
magazine.
a. A magazine is
not available for
use with
weapon.
b. Disassemble magazine. Refer
to TM 9-1005-319-10. Inspect
tube (1) for bulges, dents, or
damaged feeder lips (2).
Inspect spring (3) and follower
(4) for kinks or damage.
Replace magazine if any of
these conditions exist.
b. Tube is dented
or feeder lips
damaged.
Spring is
damaged or has
flat spots.
0008-2
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Procedure
c. Reassemble magazine and
check for binding during
operation of follower (4).
Replace magazine if follower
binds.
Equipment Not
Ready/Available
If:
c. Follower binds.
3
2
1
2
Quarterly
Charging Handle
Assembly and
Selector Lever
WARNING
If weapon fails any of the
following function tests,
perform required
maintenance. Continued
use of weapon could
result in injury to, or
death of, personnel.
0008-3
4
1 v s 0 3 3
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
2
(Cont)
Quarterly
(Cont)
Item To Be
Checked or
Serviced
ManHour
Equipment Not
Ready/Available
If:
Procedure
Charging Handle
Assembly and
Selector Lever
(Cont)
a. Pull charging handle (5) to rear. a. Charging
Check that chamber is clear.
handle does not
Let bolt carrier assembly (6)
lock in place
close. Push charging handle
when in
forward to locked position.
forward
Leave hammer in cocked
position.
position. Do not pull trigger.
5
6
1 v s 0 3 4
Selector Lever SAFE
b. Place selector lever (7) in SAFE b. Hammer falls.
position. Pull trigger (8).
Hammer should not fall.
7
S E M I
S A F E
A U T O
7
S E M I
S A F E
A U T O
8
1 v s 0 3 5
0008-4
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Selector Lever SEMI
Procedure
Equipment Not
Ready/Available
If:
c. Place selector lever (7) in SEMI c. Hammer does
position. Pull trigger (8).
not fall.
Hammer falls.
NOTE
For the purpose of the
following test, "slow" is
defined as 1/4 to 1/2 the
normal rate of trigger
release.
d. Hold trigger (8) to the rear,
d. Hammer falls.
charge weapon, and release
trigger with a slow, smooth
motion, without hesitations or
stops, until the trigger is fully
forward (an audible click should
be heard). Hammer should not
fall until trigger is pulled.
e. Repeat the SEMI position test
five times.
Selector Lever BURST
e. Weapon malfunctions
during any of
these five tests.
M16A2, M16A4, and M4 Only
f. Place selector lever (7) in
f. Hammer does
BURST position. Charge
not fall.
weapon and squeeze trigger (8).
Hammer should fall.
g. Hold trigger (8) to the rear, pull g. Hammer does
charging handle to the rear,
not fall.
and release it three times.
Release trigger. Squeeze
trigger. Hammer should fall.
NOTE
Burst disconnector should
hold hammer to the rear
when it engages deep notch
of burst cam.
0008-5
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
2
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Equipment Not
Ready/Available
If:
Charging Handle
Assembly and
Selector Lever
(Cont)
M16A3 and M4A1 Only
h. Place selector lever (7) in AUTO h. Hammer does
position. Charge weapon and
not fall.
squeeze trigger (8). Hammer
should fall.
Selector Lever AUTO
i. Hold trigger (8) to the rear,
charge weapon, and release
trigger. Squeeze trigger.
Hammer should not fall.
i. Hammer falls.
j. Repeat the BURST position test
five times.
NOTE
Automatic sear should
release hammer while
holding trigger in squeezed
position before releasing
and resqueezing trigger.
All Weapons
k. With hammer in forward
position, use moderate
finger/thumb pressure to
attempt to place selector lever
(7) in SAFE position.
Selector Lever SAFE
j. Moderate
finger/thumb
pressure moves
selector lever to
SAFE position.
7
7
S E M I
S A F E
B U R S T
8
7
S E M I
S A F E
A U T O
8
M 1 6 A 2 /M 1 6 A 4 /M 4
0008-6
M 1 6 A 3 /M 4 A 1
1 v s 0 3 6
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
3
Interval
Quarterly
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
Upper Receiver and
Barrel Assembly
(Handguard
Assemblies)
CAUTION
Do not use screwdriver or
any other tool when
removing handguard
assemblies; use of tools may
damage handguard
assemblies and/or slip.
M16A2 Only
NOTE
Refer to TM 9-1005-319-10
for "buddy system"
procedure for removing
handguard assemblies.
a. Remove and inspect handguard a. Handguard
assemblies (9) internally and
missing or
externally for cracks and/or
unserviceable.
damage. Cracks are acceptable
providing they do not extend
into the handguard retaining
flange, or adversely affect rifle
operation, operator safety, or
proper retention of handguard
assembly. Discard and replace
handguard assembly if
heatshield is loose enough to
rattle when installed on rifle.
9
1 v s 0 3 7
0008-7
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
3
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
Upper Receiver and
Barrel Assembly
(Handguard
Assemblies) (Cont)
M16A3, M16A4,
M4, and M4A1 Only
b. Remove lower handguard (10)
b. Upper hand(see WP 0015) and check for
guard assembly
loose or missing heat shield.
or lower handCheck rear flange of upper
guard missing.
handguard assembly (11) for
Heat shield of
cracks. Check upper
lower handhandguard assembly for
guard missing.
screw/retainer and forward leaf
Rear flange of
spring outside of handguard
upper handcap. Check for presence of pins
guard assembly
securing forward leaf spring
displays cracks.
and rear clamp
Screw/retainer,
(M16A3/M16A4/M4/M4A1).
forward leaf
Check for presence of barrel
spring, or rear
stop assembly (M16A3/M16A4).
clamp missing
(M16A3/M16A4/
M4/M4A1).
Barrel stop
assembly
missing
(M16A3/
M16A4).
1 1
1 0
1 v s 0 3 8
0008-8
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
4
Interval
Quarterly
ManHour
Item To Be
Checked or
Serviced
Procedure
Upper Receiver and
Barrel Assembly
(Serviceability
Check)
Equipment Not
Ready/Available
If:
WARNING
DRY CLEANING SOLVENT
CAUTION
Damage may occur if
excessive force is used to
release takedown pin or
pivot pin. Use hand
pressure ONLY.
a. Release takedown pins and
open and separate receivers.
Hand check compensator (12)
for looseness on barrel (13);
then hand check barrel for
looseness on upper receiver
(14). Check center slot of
compensator for alignment
(WP 0015).
a. Compensator or
barrel is loose.
1 7
1 5
1 3
1 6
1 2
1 4
1 v s 0 3 9
0008-9
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
4
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Equipment Not
Ready/Available
If:
Upper Receiver and b. Check gas tube (15), forward
b. Gas tube,
Barrel Assembly
assist assembly (16), and rear
forward assist
(Serviceability
sight assembly (17) for damage.
assembly, or
Check) (Cont)
rear sight
assembly is
damaged.
c. Push in on forward assist
assembly (16) several times to
check for slippage of the
forward assist pawl. SH - If
slippage occurs, refer to TM 91005-319-10 for lubrication
instructions.
d. Rear sight spring should retain
rear sight assembly (17) in
either position with firmness
(M16A2 only).
0008-10
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
NOTE
If front or rear sight is
moved, return to original
position.
e. Check front sight post, detent,
and spring (18) for damage and
corrosion. Clean and lubricate.
Check charging handle (5) and
ejection port cover (19) for
defects and proper function.
Check sling swivel (20) and
rivet (21) for damage and
proper function. SH Components other than
charging handle are defective;
replace as necessary.
e. Charging
handle is
defective.
5
1 8
1 9
2 1
2 0
0008-11
1 v s 0 4 0
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
4
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Upper Receiver and
Barrel Assembly
(Serviceability
Check) (Cont)
Equipment Not
Ready/Available
If:
CAUTION
Do not use a wire brush to
roughen surfaces.
If solid film lubricant comes
in contact with moving parts
or functioning surfaces of
the weapon, remove
lubricant immediately by
washing with dry cleaning
solvent.
NOTE
Shiny metal exterior
surfaces of the rifle should
be re-coated with solid film
lubricant (WP 0045, item
20). Clean surface with dry
cleaning solvent (WP 0045,
item 15). Dry, roughen with
abrasive cloth (WP 0045,
item 13), and apply solid
film lubricant.
f. Inspect finish of upper receiver
(14) for scratches or worn shiny
spots.
g. Inspect for painted surfaces on
weapon.
0008-12
g. Weapon has
been painted.
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Procedure
WARNING
DRY CLEANING SOLVENT
WARNING
SOLID FILM LUBRICANT
h. If scratched or worn shiny in
spots, disassemble and remove
all lubricant from surface with
dry cleaning solvent (WP 0045,
item 15). Wear rubber gloves
(WP 0045, item 17) and use a
wash pan (WP 0045, item 26) to
apply solvent. Let parts dry
thoroughly. Roughen the
surface using abrasive cloth
(WP 0045, item 13) and apply
solid film lubricant (WP 0045,
item 20). Allow 16 to 24 hours
to dry before handling.
0008-13
Equipment Not
Ready/Available
If:
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
4
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
Upper Receiver and i. Hold barrel (13) at 40-degree
i. Adjustment
Barrel Assembly
angle (muzzle down). Pull
does not correct
(Serviceability
charging handle (5) to rear.
the malfunction.
Check) (Cont)
Hold bolt carrier assembly (6)
to rear and push charging
handle forward. Release bolt
carrier assembly. The bolt
carrier assembly should close
and lock under its own weight.
If it does not, remove the bolt
assembly (22) from the key and
bolt carrier assembly (23) and
slide the key and bolt carrier
assembly (without bolt) back
and forth in the upper receiver
and barrel assembly. If the gas
tube (15) hits the carrier key
(24) on the inside of the upper
receiver (14), or if the gas tube
binds in the carrier key, correct
the malfunction by adjusting
(slightly bending) the gas tube
in the area of the handguard
assemblies.
2 3
2 4
2 2
5
6
1 5
1 4
1 3
1 v s 0 4 1
0008-14
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Procedure
Equipment Not
Ready/Available
If:
M16A3/M16A4
and M4/M4A1 Only
j. Inspect back-up iron sight
(BUIS) (25) and mounting
surface (26) of upper receiver
(14) for damage. If BUIS is
missing or cannot be correctly
mounted, repair as authorized.
j. Back-up iron
sight is missing
or damaged or
cannot be
securely
mounted.
2 5
2 6
2 5
1 4
1 v s 0 4 2
0008-15
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
5
Interval
Quarterly
ManHour
Item To Be
Checked or
Serviced
Procedure
Key and Bolt
Carrier Assembly
and Bolt Assembly
(Serviceability
Check)
Equipment Not
Ready/Available
If:
WARNING
Unless performed by
qualified maintenance
personnel, do not
interchange bolt
assemblies from one
weapon to another.
Doing so may result in
injury to, or death of,
personnel.
a. Remove and disassemble (WP
0011). Visually inspect bolt
assembly (22) for cracks,
especially in the area of the
bolt cam pin hole (27). Check
for cracks on locking lugs (28),
for a cluster of pits or chipped
bolt face (29), and for an
elongated firing pin hole (30).
If cracked or broken, replace.
a. Defects are
found.
b. Check for worn or missing bolt b. Bolt assembly
rings (31). Check for proper
drops out of key
staggering of bolt rings. Insert
and bolt carrier
bolt assembly (22) into key and
assembly due to
bolt carrier assembly (23).
its own weight.
Turn key and bolt carrier
Firing pin
assembly so bolt assembly
retaining pin or
points down. Bolt assembly
bolt cam pin is
must not drop out. Remove bolt
missing or
assembly. Check for broken or
broken.
missing firing pin retaining pin
(32) and bolt cam pin (33);
replace as necessary.
0008-16
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
3 2
2 3
3 3
2 7
3 0
2 2
3 1
2 9
2 8
1 v s 0 4 3
c. Check cartridge extractor (34),
extractor spring assembly (35),
cartridge ejector (36), and
ejector spring (37) for dirt and
serviceability. If dirty, clean,
lubricate, and assemble. If
unserviceable, replace as
necessary.
c. Parts are
missing or
unserviceable.
d. Check key and bolt carrier
assembly (23) and carrier key
(24) for damage and looseness.
d. Key and bolt
carrier
assembly or
carrier key is
damaged, or
carrier key is
loose.
NOTE
If carrier key is dented, see
WP 0011 for repair.
e. Check firing pin (38) for chips
or breaks. Pits or wear in area
of flange (39) is permissible.
3 7
2 3
3 6
3 5
3 4
3 8
2 4
3 9
1 v s 0 4 4
0008-17
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
6
Interval
Quarterly
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
Lower Receiver and a. Remove buffer assembly (40)
Buttstock Assembly
and action spring (41). Check
(Serviceability
buffer assembly for cracks.
Check)
Check action spring for kinks
and free length. Free length for
rifle should be 11 3/4 inches
(29.85 cm) minimum to13 1/2
inches (34.29 cm) maximum.
Free length for carbine should
be 10 1/16 inches (25.56 cm)
minimum to 11 1/4 inches
(28.58 cm) maximum. Do not
attempt to adjust spring length.
SH - Buffer assembly is
cracked; action spring is kinked
or does not meet free length
requirements.
4 0
C A R B I N E
4 0
R I F L E
4 1
1 v s 0 4 5
0008-18
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Procedure
Equipment Not
Ready/Available
If:
b. Remove pistol grip screw (42),
b. Components are
lockwasher (43), pistol grip (44),
defective/
helical spring (45), safety detent
damaged.
(46), pivot pin (47), pivot pin
detent (48), and helical spring
(49). Clean and lubricate metal
components. Also clean and
generously lubricate pivot pin
holes and spring/detent holes.
Replace defective/damaged
components as necessary.
4 8
4 6
4 5
4 9
4 4
4 3
4 7
4 2
1 v s 0 4 6
0008-19
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
6
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
Lower Receiver and
Buttstock Assembly
(Serviceability
Check) (Cont)
Rifle Only
c. Disengage takedown pin (50)
c. Components are
and pull out; push back in to redefective/
engage takedown pin (an
damaged.
audible click should be heard).
If an audible click is not heard,
repair.
d. Lubricate helical compression
spring (51) and takedown pin
detent (52) by placing one drop
of lubricant on takedown pin
detent and lowering buttstock
assembly (53) to vertical
position. Allow lubricant to
work its way around the helical
compression spring and
takedown pin detent.
e. Check components of buttstock
assembly (53) for damage.
5 0
5 3
5 1
5 2
1 v s 0 4 7
0008-20
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Procedure
Rifle Only
f. Cracks in the critical area at
the front end of buttstock are
not acceptable. Under the
following conditions, hairline
cracks (no chipped away
material allowed) originating
from the buttplate end of the
buttstock are acceptable.
Equipment Not
Ready/Available
If:
f. Buttstock is
cracked in
critical area or
does not meet
crack criteria.
(1) One hairline crack, not to
exceed 1 in. (2.54 cm) in
length, per side of
buttstock.
(2) Two additional hairline
cracks up to 0.25 in. (0.64
cm) in length, per side of
buttstock.
(3) A total of three cracks per
side of buttstock,
originating from buttplate
end, is allowable.
C R I T I C A L A R E A
1 v s 0 4 8
0008-21
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
6
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Equipment Not
Ready/Available
If:
Rifle Only
Lower Receiver and
Buttstock Assembly
(Serviceability
Check) (Cont)
NOTE
A small amount of side-toside, up-and-down, or
rotational movement of
buttstock assembly is
acceptable.
g. Check buttstock assembly (53)
for forward to rear movement
and/or a 1/32 in. (0.079 cm) gap
between buttstock assembly
and lower receiver (54). If
forward to rear movement is
present and/or a 1/32 in. (0.079
cm) gap appears, tighten
machine screw (55). If still not
tight, remove buttstock
assembly and check for loose
receiver extension (56). If
receiver extension is loose,
repair. If not loose, replace
buttplate (57), using new
machine screw.
h. Check buttplate (57) for cracks
or damage.
(1) Cracks are visible around
the buttplate mounting hole
while screws are mounted.
SH - Cracks are visible
around mounting holes
when installed on rifle.
(2) Cracks or separations
around door assembly are
visible when the door
assembly is closed. SH Cracks are visible when
door assembly is closed.
0008-22
g. Lower receiver
extension
cannot be
tightened.
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
(3) If buttplate is cracked in
excess of 0.25 in. (0.64 cm)
in length and extends
through buttplate (57),
repair. SH - Crack in excess
of 0.25 in. extends through
buttplate.
(4) Buttplate (57) should not be
removed except for repair or
replacement of parts at
which time a new machine
screw, NSN 5305-01-1478585, must be used.
5 5
5 3
5 7
5 6
5 4
0008-23
1 v s 0 4 9
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
6
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Lower Receiver and
Buttstock Assembly
(Serviceability
Check) (Cont)
Equipment Not
Ready/Available
If:
Carbine Only
i. Extend buttstock assembly (58).
Grasp lock release lever (59) in
area of retaining nut (60), pull
downward, and slide buttstock
assembly to rear to separate
buttstock assembly from lower
receiver extension (61).
j. Clean and lubricate takedown
pin (62). Lubricate takedown
pin detent (63) and spring (64)
by placing lubricant on detent
and exercising it with a small
screwdriver.
k. Clean buttstock assembly (58)
k. Lock release
inside and out. Check lock
lever is cracked,
release lever (59) for free movedoes not move
ment. Check for cracks, dents,
freely, or is
and damage to buttstock
dented or
assembly.
damaged
enough to
interfere with
functioning.
l. Hand check lower receiver
l. Lower receiver
extension (61) for looseness and
extension is
corrosion. If loose, repair.
loose.
Clean and lubricate lower
receiver extension.
m. Grasp lock release lever (59) in
area of retaining nut (60) and
pull to install buttstock
assembly (58) onto lower
receiver extension (61).
0008-24
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
ManHour
Item To Be
Checked or
Serviced
Equipment Not
Ready/Available
If:
Procedure
5 8
6 1
5 9
6 3
6 0
6 4
6 2
1 v s 0 5 0
All Weapons
n. Function check magazine catch
(65) and bolt catch (66).
n. Magazine catch
or bolt catch is
defective.
6 5
6 6
5 4
1 v s 0 5 1
0008-25
TM 9-1005-319-23&P
0008
PMCS PROCEDURES - Continued
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
Interval
6
(Cont)
Quarterly
(Cont)
ManHour
Item To Be
Checked or
Serviced
Procedure
Lower Receiver and
Buttstock Assembly
(Serviceability
Check) (Cont)
NOTE
If a weapons lower receiver
is missing one third or more
of its exterior protective
finish, resulting in an
unprotected/light reflecting
surface, it is a candidate for
overhaul. This missing
finish will be considered a
shortcoming (SH). This SH
requires action to obtain a
replacement weapon. Once
a replacement has been
received, evacuate the
original weapon to depot for
overhaul.
o. Check finish of lower receiver
(54) for scratches and worn
shiny spots. If scratched or
worn shiny in spots, repair in
the same manner as stated for
upper receiver (see item 4
above).
7
Quarterly
M16 Series Rifles
and M4 Series
Carbines
a. Assemble per TM 9-1005-31910.
b. Check sling for damage. If
damaged, replace.
c. Check for improperly
assembled, broken, missing, or
damaged parts. Check overall
general appearance. Replace
parts or repair as required.
0008-26
Equipment Not
Ready/Available
If:
TM 9-1005-319-23&P
0008
Table 1. Preventive Maintenance Checks and Services for
M16 Series Rifles and M4 Series Carbines - Continued.
Item
No.
8
Interval
ManHour
Quarterly
Item To Be
Checked or
Serviced
Annual Safety and
Serviceability
Inspection and
Gaging
Procedure
Check to ensure annual safety and
serviceability inspection and
gaging has been done and that the
next gaging and inspection is
scheduled.
Equipment Not
Ready/Available
If:
Annual gaging has
not been
performed. Air
Force users only
will refer to AFI
36-2226 for
inspection
requirements.
END OF TASK
LUBRICATION INSTRUCTIONS
The term "cleaner, lubricant, and preservative (CLP)" or the words "lubricant", "LSA", or "LAW" are to be
interpreted to mean CLP (WP 0045, item 10), weapons lubricating oil (LSA) (WP 0045, item 21), or weapons
lubricating oil (LAW) (WP 0045, item 22). Lubricants can be utilized as applicable, with the following
constraints.
CAUTION
Do not mix lubricants on the same weapon. The weapon must be thoroughly cleaned
during change from one lubricant to another. Dry cleaning solvent (WP 0045, item
15) is recommended for cleaning during change from one lubricant to another.
1.
Under all but the coldest Arctic conditions, LSA or CLP is the lubricant to use on the weapon. Either
may be used at -10 °F (-23 °C) and above. However, do not use both on the same weapon at the same
time.
2.
LAW is the lubricant to use during cold Arctic conditions, +10 °F (-12 °C) and below.
3.
Any of the lubricants may be used from -10 °F to +10 °F (-23 °C to -12 °C).
4.
Rifle bore cleaning compound (RBC) (WP 0045, item 12) may be used to remove carbon buildup in the
bore and other portions of the weapon.
5.
Users will use only those cleaners, lubricants, or preservatives listed in WP 0045. No other cleaners,
lubricants, or preservatives are authorized.
END OF TASK
END OF WORK PACKAGE
0008-27/28 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
RIFLE, 5.56MM (M16A2) 9349000; RIFLE, 5.56MM (M16A3) 12012000;
RIFLE, 5.56MM (M16A4) 12973001; CARBINE, 5.56MM (M4) 9390000;
AND CARBINE, 5.56MM (M4A1) 12972700 MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY,
TEST AND INSPECTION, STOWAGE
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Adapter bar (WP 0030, Figure 6)
Mounting bracket (WP 0045, item 23)
Rail protector (WP 0045, item 29)
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Solid film lubricant (SFL) (WP 0045, item 20)
References
TM 9-1005-319-10
WP 0015
WP 0021
Equipment Condition
Weapon assembled
0009-1
0009
TM 9-1005-319-23&P
0009
DISASSEMBLY
WARNING
Before starting an inspection, be sure to clear the weapon. Do not pull the
trigger until the weapon has been cleared. Inspect the chamber to ensure
that it is empty and no ammunition is in position to be chambered.
2
1
3
7
7
2
2
3
3
1
1
8
6
4
6
5
8
6
4
M 4 /M 4 A 1 C A R B I N E
M 1 6 A 2 R I F L E
4
5
5
M 1 6 A 3 /M 1 6 A 4 R I F L E
1 v s 0 5 2
Figure 1. Major Components of Rifles and Carbines.
Remove magazine (4), sling (5), bolt and bolt carrier assembly (3), charging handle assembly (2), upper
receiver and barrel assembly (1), vertical pistol grip (8), and back-up iron sight (7) from lower receiver and
buttstock assembly (6). Refer to TM 9-1005-319-10.
END OF TASK
REPAIR OR REPLACEMENT
WARNING
SOLID FILM LUBRICANT
Solid Film Lubricant (SFL) (WP 0045, item 20) is the only authorized touchup for the M16 series rifles and
M4/M4A1 carbines and may be used on up to one third of the exterior finish of the weapon. FOR ARMY
CONUS USE ONLY: SFL may be used as touchup without limitation on the upper receiver and barrel
assembly. Units which DO NOT fall under the category of Divisional Combat Units or rapid deployment
type units may have up to 100 percent of the exterior surface of the upper receiver and barrel assembly
protected with SFL if necessary.
0009-2
TM 9-1005-319-23&P
0009
AIR FORCE ONLY: The only permissible coatings or coverings authorized for Air Force owned or
controlled weapons are:
Receiver: Color hardcoat anodizing applied by qualified Depot personnel only;
Any steel components: Phosphate coat applied by qualified Depot personnel only;
Touchup of small damaged or shiny areas: SFL applied by qualified Combat Arms personnel only.
Painting or otherwise camouflaging Air Force weapons is not authorized.
END OF TASK
ASSEMBLY
WARNING
Unless performed by qualified maintenance personnel, do not interchange
bolt assemblies from one weapon to another. Doing so may result in injury
to, or death of, personnel.
1.
Install charging handle assembly (2) and bolt and bolt carrier assembly (3) into upper receiver and
barrel assembly (1). Join upper receiver and barrel assembly and lower receiver and buttstock
assembly (6).
2.
Snap on sling (5) and install magazine (4).
3.
Install back-up iron sight (7) and vertical pistol grip (8) (M16A3/M16A4 and M4/M4A1 only).
END OF TASK
TEST AND INSPECTION
1.
Visually inspect general appearance of weapon. Weapon should look new. All metal surfaces are to
have a dull, rust- or corrosion-resistant finish with no burrs or deep scratches.
2.
Visually inspect barrel for serviceability. Barrels must be straight, clean, free of rust, powder fouling,
and free of bulges and rings. Fine pitting is allowable.
3.
Using moderate hand pressure, check for rotational movement of the front sight in relation to the
barrel. Also, using moderate hand pressure, check for rotational movement of the barrel in relation to
the upper receiver. If movement between the front sight and the barrel exist, the barrel assembly must
be replaced. If movement between the barrel and the upper receiver exist, the barrel assembly must be
aligned and tightened (see WP 0015).
4.
Visually inspect weapon for missing parts. All parts must be attached and all modifications must be
applied. Steel parts must be rust free. Spring pins must be secure and screws must be tight.
0009-3
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
5.
Functionally inspect key and bolt carrier assembly and gas tube alignment. Refer to TM 9-1005-319-10
and use the following procedures:
a.
Disengage the takedown pin and open the receiver.
b.
Remove bolt carrier assembly.
c.
Remove bolt assembly from bolt carrier assembly.
d.
Insert key and bolt carrier assembly into upper receiver and barrel assembly. The bolt assembly
must not be installed while performing test.
e.
Slide key and bolt carrier assembly forward to detect binding between key and bolt carrier
assembly and gas tube by feel. Badly bent gas tube could cause damage to both the key and bolt
carrier assembly and the gas tube. A slightly bent gas tube will cause unnecessary wear of the key
and bolt carrier assembly and gas tube.
f.
Correct slight binding by removing handguard assemblies and slightly bending gas tube in the
handguard area while repeating step e above until no binding is detected. Badly bent gas tubes
will be replaced and realigned.
g.
Remove key and bolt carrier assembly from upper receiver and barrel assembly.
h.
Reassemble bolt assembly into key and bolt carrier assembly.
i.
Reinstall key and bolt carrier assembly into upper receiver and barrel assembly.
M16A2 ONLY
6.
Check rear sight assembly as follows:
a.
Rotate elevation knob counterclockwise until the rear sight assembly is all the way down. If a
whole click is not felt as the rear sight assembly stops, the rear sight assembly has bottomed out
and will not pivot freely.
b.
Position elevation knob back slightly to its last whole click as the rear sight assembly base is under
tension of the ball bearing and helical spring. The 300 meter mark should align with the mark on
the receiver.
c.
If the 300 meter mark is not aligned with the mark on receiver, slip the range scale in the following
manner:
(1)
Position the 300 meter mark with the mark on the receiver.
(2)
Insert a 1/16 in. key wrench through the access hole of the rear sight assembly base and into
the index screw.
(3)
Loosen the index screw three turns and leave the wrench in place.
(4)
Rotate lower portion of elevation knob counterclockwise until it stops (range scale should not
have moved). Elevation knob should be positioned on its last whole click.
0009-4
TM 9-1005-319-23&P
(5)
Tighten index screw and remove wrench.
(6)
Check for proper setting.
0009
ALL WEAPONS
7.
Make a functional check on an assembled weapon with selector lever in SAFE, SEMI, and
BURST/AUTO positions. Any portion of this check may be used alone to determine the operational
condition of any specific firing position selected.
a.
Remove magazine if installed. Pull charging handle assembly to rear. Check that chamber is
clear. Let bolt and bolt carrier assembly close. Do not pull trigger. Leave hammer in cocked
position.
WARNING
If weapon fails any function tests, perform required maintenance.
Continued use of the weapon could result in injury to, or death of,
personnel.
b.
Place selector lever in SAFE position and pull trigger. Hammer should not fall.
c.
Place selector lever in SEMI position. Pull trigger. Hammer should fall.
NOTE
For the purpose of the following check "SLOW" is defined as 1/4 to 1/2 the normal
rate of trigger release.
d.
Hold trigger to the rear, charge weapon, and release the trigger with a slow, smooth motion,
without hesitations or stops, until the trigger is fully forward; an audible click should be heard.
Hammer should not fall.
e.
Repeat the SEMI position test five times. The weapon must not malfunction during any of these
five tests. If the weapon malfunctions during any of these five tests, repair (see WP 0021).
M16A2, M16A4, and M4 ONLY
f.
Place selector lever in BURST position. Charge weapon and pull trigger. Hammer should fall.
g.
While holding trigger to the rear, pull charging handle assembly to rear and release three times.
Release trigger. Hammer should not fall. The burst disconnector should have held the hammer to
the rear while the trigger was in the pulled position. See item 14 for detailed explanation and
function check of three-round burst.
h.
Pull trigger. Hammer should fall. This should be the first round of a three-round burst.
0009-5
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
M16A3 and M4A1 ONLY
i.
Place selector lever in AUTO position. Charge weapon and pull trigger. Hammer should fall.
j.
Hold trigger to the rear, charge weapon, and release trigger. Pull trigger. Hammer should not fall.
AUTO sear should have released hammer as the bolt closed.
ALL WEAPONS
k.
8.
9.
With hammer in forward position, attempt to place the selector lever in the SAFE position. If
selector lever can be placed on SAFE, repair (see WP 0021).
Perform the following additional functional checks and adjustments on assembled weapon:
a.
Press magazine catch button. Make sure it functions properly.
b.
Press bolt catch. Make certain it operates smoothly and holds bolt in open position.
c.
Inspect front sight and rear sight assembly. Make certain they can be adjusted properly.
d.
Actuate forward assist assembly. It must work freely.
e.
Inspect upper receiver and barrel assembly. Barrel assembly should not rotate within upper
receiver assembly.
f.
Check that third or middle slot of compensator is straight up at top dead center (TDC).
Test trigger pull as follows:
M16A2, M16A4, and M4 ONLY
a.
Clear the weapon. Place selector lever in BURST position. Pull the trigger and hold it to the rear.
Pull the charging handle to the rear and return to the bolt closed position three times. (This will
place the BURST disconnector in the deep notch of the BURST cam.)
0009-6
TM 9-1005-319-23&P
3 L B
(1 3 6 1 G )
0009
2 L B
(9 0 7 G )
2 L B 8 O Z
(1 1 3 4 G )
2 L B 8 O Z
(1 1 3 4 G )
1 L B 8 O Z
(6 8 0 G )
1 v s 0 5 3
Figure 2. Trigger Pull Test.
b.
Release the trigger. Place the selector lever in SEMI position. Hold the weapon in the vertical
position. Using trigger pull measuring fixture, P/N 7274758, add weights until hammer trips.
Determine weight applied.
c.
Hammer must not trip when 5.5 lb (2.49 kg) have been applied; hammer must trip on applying
9.5 lb (4.31 kg).
M16A3 and M4A1 ONLY
d.
Clear the weapon. Cock weapon. Place selector lever in SEMI position and hold weapon in vertical
position.
e.
Using trigger pull measuring fixture P/N 7274758, add weights until hammer trips. Determine
weight applied.
f.
Hammer must not trip when 5.5 lb (2.49 kg) have been applied. Hammer must trip on applying
8.5 lb (3.86 kg).
ALL WEAPONS
g.
If weapon fails trigger pull test or excessive creep is present, replace trigger assembly and/or
hammer assembly (see WP 0021).
NOTE
Always gage trigger and hammer pin holes with no go plug gage P/N 12006472 before
replacing parts.
10.
Check headspace using headspace gage P/N 7799734. See WP 0015.
11.
Check firing pin protrusion using firing pin protrusion gage P/N 7799735. See WP 0015.
12.
Check extent of barrel erosion using barrel erosion gage P/N 8448496. See WP 0015.
0009-7
TM 9-1005-319-23&P
TEST AND INSPECTION - Continued
13.
Check barrel straightness using barrel straightness gage P/N 8448202. See WP 0015.
NOTE
Review step 14 only if problems are encountered during selector lever tests.
First become familiar with the functioning of the firing mechanism, especially when
in the SAFE and SEMI positions. Also understand the role that the automatic sear
plays when firing in the BURST position. Functioning of the mechanism is explained
below in a step by step manner. This actually will seem to complicate something that
is really very simple and happens in less than 1 second. The diagrams on the
following pages do not show the associated springs for the sake of simplicity. The
positioning of the burst cam is shown in detail.
14.
The following is a description of the functional theory of three-round burst.
NOTE
Assume the rifle is fully loaded with a live round in the chamber and the selector
lever on BURST.
1 v s 0 5 4
Figure 3. Beginning Position in Three-Round Burst.
a.
Hammer is cocked.
b.
Front hook of burst lever is in stop notch.
0009-8
0009
TM 9-1005-319-23&P
0009
F R O N T
H O O K
S T O P
N O T C H
1 v s 0 5 5
Figure 4. Firing of First Round.
c.
Trigger is pulled.
d.
Trigger nose drops and hammer falls firing the FIRST ROUND.
e.
Front hook of burst disconnector holds burst cam in place as hammer falls.
NOTE
Anytime the hammer falls forward, the clutch spring releases the burst cam and
allows the front hook of the burst disconnector to keep it in place.
1 v s 0 5 6
Figure 5. Movement of Key and Bolt Carrier Assembly.
f.
As the key and bolt carrier assembly moves to the rear, the hammer is forced to the rear.
0009-9
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
1 v s 0 5 7
Figure 6. First Rotation of Burst Cam.
g.
The clutch spring of the burst cam clutches the burst cam and causes it to rotate one notch as the
hammer is forced back.
1 v s 0 5 8
Figure 7. Action of Automatic Sear.
h.
When hammer is fully to the rear, the automatic sear catches it.
1 v s 0 5 9
Figure 8. Burst Disconnector in Second Notch.
i.
The front hook of the burst disconnector is now fully in the second notch.
0009-10
TM 9-1005-319-23&P
0009
1 v s 0 6 0
Figure 9. Forward Travel of Key and Bolt Carrier Assembly.
j.
As the key and bolt carrier assembly travels forward, the automatic sear releases the hammer and
the hammer falls.
1 v s 0 6 1
Figure 10. Firing of Second Round.
k.
When the hammer falls, the SECOND ROUND is fired.
0009-11
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
1 v s 0 6 2
Figure 11. Rearward Movement of Key and Bolt Carrier Assembly.
l.
As the key and bolt carrier assembly moves to the rear, the hammer is forced back to the rear.
1 v s 0 6 3
Figure 12. Second Rotation of Burst Cam.
m. The clutch spring of the burst cam clutches against the burst cam and causes it to rotate one notch
as the hammer is forced back.
1 v s 0 6 4
Figure 13. Second Round Action of Automatic Sear.
n.
When hammer is fully to the rear, the automatic sear catches it.
0009-12
TM 9-1005-319-23&P
0009
1 v s 0 6 5
Figure 14. Burst Disconnector in Third Notch.
o.
The front hook of the burst disconnector is now fully in the third notch.
1 v s 0 6 0
Figure 15. Release of Hammer Assembly.
p.
As the key and bolt carrier assembly travels forward, the automatic sear releases the hammer and
the hammer falls.
1 v s 0 6 6
Figure 16. Firing of Third Round.
q.
When the hammer falls, the THIRD ROUND is fired.
0009-13
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
1 v s 0 6 2
Figure 17. Final Movement of Key and Bolt Carrier Assembly.
r.
As the key and bolt carrier assembly moves to the rear, the hammer is forced back to the rear.
1 v s 0 6 7
Figure 18. Third Rotation of Burst Cam.
s.
The clutch spring of the burst cam clutches against the burst cam and causes it to rotate one notch
as the hammer is forced back.
0009-14
TM 9-1005-319-23&P
0009
1 v s 0 5 4
1 v s 0 6 5
Figure 19. Rotation into Stop Notch.
t.
When the hammer is fully to the rear, it is initially caught by the automatic sear. However, the
front hook of the burst disconnector is now fully in the next stop notch which is deeper than the
others.
R E A R H O O K
1 v s 0 6 8
Figure 20. Completion of Firing.
u.
Because a stop notch is deeper than the others, it allows the front hook of the burst disconnector
further forward than before. This allows the rear hook of the burst disconnector to latch on the
rear hammer notch. This holds the hammer fully to the rear even though the trigger is still to the
rear. This happens when the burst is over and the firing is stopped.
0009-15
TM 9-1005-319-23&P
0009
TEST AND INSPECTION - Continued
1 v s 0 6 9
Figure 21. Release of Trigger.
v.
Once the trigger is released, the trigger nose comes up and holds the hammer back.
NOTE
Pulling the trigger to the rear and holding it back again will fire another three-round
burst. This will continue until the magazine is empty. However, the trigger must be
released between each burst.
END OF TASK
STOWAGE
NOTE
Prior to stowing the weapon in arms room, perform steps 1 through 4.
1.
Clear weapon. Refer to TM 9-1005-319-10.
2.
Place selector lever in SEMI position.
3.
Pull trigger. Hammer should fall.
4.
Close ejection port (dust) cover.
5.
Place weapon in rack.
0009-16
TM 9-1005-319-23&P
0009
1 v s 0 7 0
Figure 22. Stowage of Weapon.
6.
Use M12 Storage Rack after modifying as described below.
a.
The M12 storage rack is the correct arms rack in which to store the M4/M4A1 carbine. The carbine
must be stored with buttstock extended. The back-up iron sight must be mounted in rearmost slot
of upper receiver. When storing the M4/M4A1 carbine in the M12 storage rack a mounting bracket
(WP 0045, item 23) may be used for each carbine being stored. This option is for the convenience of
the person who opens and closes the storage rack to store the carbines.
b.
To install the mounting bracket on the M12 storage rack, for use with the carbine, install the
bracket with the hooks of the bracket facing toward the carbine, so that the lower receiver
extension will contact the bent end of the bracket. The bent end of the bracket will hold the carbine
upright when the arms rack is opened. The bracket can be turned around when not in use for the
carbine to allow storage of the M16 series rifle.
c.
When storing the M4/M4A1 carbine in the M12 storage rack, an adapter bar (WP 0030, Figure 6)
MUST be used for security reasons.
NOTE
It is necessary to either remove the carrying handle, if present, or ensure that it is in
rearmost position in order to secure the locking bars of the M12 rack during storage
of the M16A4 rifle and M4/M4A1 carbine. DO NOT mix carrying handles from one
weapon to another; it may change the zero of the host weapon.
d.
To prevent damage to the mounting surface on the upper receiver it is recommended that the rail
protector (WP 0045, item 29) should be used during storage of the carbines and M16A4 rifle when
the back-up iron sight or some other accessory is not installed on the upper receiver.
END OF TASK
END OF WORK PACKAGE
0009-17/18 blank
TM 9-1005-319-23&P
0010
FIELD MAINTENANCE
BACK-UP IRON SIGHT MAINTENANCE
REMOVAL, DISASSEMBLY, REPAIR OR REPLACEMENT,
ASSEMBLY, LUBRICATION, INSTALLATION
EFFECTIVITY NOTICE
M16A3, M16A4 RIFLE
M4, M4A1 CARBINE
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Recoil screw, 12996824
References
TM 9-1005-319-10
REMOVAL
WARNING
Before starting removal procedure, clear the weapon. Inspect the chamber
to ensure that it is empty and no ammunition is in position to be
chambered.
1.
Remove magazine. Draw bolt/carrier assembly to the rear and visually inspect chamber and receiver to
make sure weapon is unloaded and no ammunition is present. Close bolt/carrier assembly; confirm
that selector lever is set on SAFE, and close dust cover.
0010-1
TM 9-1005-319-23&P
0010
REMOVAL - Continued
1
2
3
4
1 v s 0 7 1
Figure 1. Removal of Back-up Iron Sight.
2.
Using 1/8 in. key wrench, remove recoil screw (1). Remove locking bar (2) and back-up iron sight
(BUIS) (3) from upper receiver (4). Discard recoil screw.
END OF TASK
0010-2
TM 9-1005-319-23&P
0010
DISASSEMBLY
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
1 0
1 0
5
6
7
8
1 1
9
1 2
1 3
1 5
1 7
1 4
1 1
1 6
1 v s 0 7 2
Figure 2. Disassembly/Assembly of BUIS.
1.
Drive out spring pin (5) using hammer and 1/16 in. punch.
2.
Catch windage knob (6), index spring (7), and ball bearing (8).
3.
Using a flat bladed screwdriver, remove windage screw (9).
4.
Remove frame assembly (with aperture sight) (10), and carefully remove compression spring (12) and
plunger (13), from point beneath frame assembly.
NOTE
Disassemble the sight cam (11) only when necessary. If removed, discard external
retaining ring.
5.
Using retaining ring pliers, remove external retaining ring (16) and slide out sight cam (11) from sight
base (17). Use care to retain parts when removing ball bearing (15) and index spring (14) underneath
sight cam.
END OF TASK
0010-3
TM 9-1005-319-23&P
0010
REPAIR OR REPLACEMENT
1.
Check sight parts for serviceability. Visually inspect sight base for cracks, corrosion, or damage.
Check for legibility of markings. Detent indexing surfaces should be well formed. Replace if defective.
2.
Visually inspect frame assembly for cracks, corrosion, or damage. Sight aperture should be round.
Flip-up sight arm must lock down. Replace if defective.
3.
Check sight cam for function, corrosion, or damage. Replace if defective.
4.
Visually check locking bar for damage. Replace if defective.
END OF TASK
ASSEMBLY
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
NOTE
The external retaining ring must be replaced if removed for repair of the sight cam.
1.
If removed, install sight cam (11) into sight base (17). Push ball bearing (15) and index spring (14) into
hole in sight cam and slide sight cam all the way into sight base. Fasten in place with new external
retaining ring (16).
2.
Install compression spring (12) and plunger (13) into frame assembly (10). Install frame assembly into
sight base (17). (It may be easier to rotate sight cam (11) to the 200-meter mark to slide frame
assembly into position and then rotate to the 600-meter mark to hold frame assembly while inserting
windage screw.)
3.
Install windage screw (9) into sight base (17).
4.
Install index spring (7) and ball bearing (8) into hole in windage knob (6). Align hole in windage knob
with hole in windage screw (9) and fasten in place with spring pin (5).
END OF TASK
LUBRICATION
1.
Lubricate BUIS with overall light coat of CLP (WP 0045, item 9).
2.
Rotate sight cam to 600-meter mark. Apply 2 or 3 drops of CLP to index spring and ball bearing
through hole in bottom of sight cam.
3.
Apply 2 or 3 drops of CLP to plunger and compression spring beneath flip-up aperture sight.
0010-4
TM 9-1005-319-23&P
0010
4.
Apply 2 or 3 drops of CLP to index spring and ball bearing through hole in side of windage knob.
5.
Apply light coat of CLP to threads of windage screw. Turn screw side-to-side before returning to
original zeroing mark.
END OF TASK
INSTALLATION
1
2
3
4
1 v s 0 7 1
Figure 3. Installation of Back-up Iron Sight.
NOTE
Recoil screw is mandatory replacement when removed. There is a locking patch on
threads of screw.
1.
Install locking bar (2) and new recoil screw (1) into BUIS (3).
NOTE
The BUIS MUST be mounted in the rearmost slot on the upper receiver for the range
adjustments and the zeroing to be correct.
2.
Using locking bar (2) and recoil screw (1) align recoil screw in rearmost slot of upper receiver (4) with
range scale of BUIS (3) facing rearward. Make sure BUIS is flat on receiver rail with angled edge
under upper receiver rail and tighten in place with 1/8 in. key wrench.
END OF TASK
END OF WORK PACKAGE
0010-5/6 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
BOLT AND BOLT CARRIER ASSEMBLY MAINTENANCE
DISASSEMBLY, CLEANING, INSPECTION — ACCEPTANCE AND REJECTION CRITERIA,
REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Bolt carrier key tool (WP 0039, Figure 23, item 12)
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Pipe cleaner (WP 0045, item 11)
Rifle bore cleaning compound (RBC) (WP 0045, item 12)
References
TM 9-1005-319-10
WP 0012
WP 0013
Equipment Condition
Bolt and bolt carrier assembly removed (WP 0009)
0011-1
0011
TM 9-1005-319-23&P
0011
DISASSEMBLY
2
3
1
5
4
1 v s 0 7 3
Figure 1. Disassembly of Bolt and Bolt Carrier Assembly.
CAUTION
To prevent damage to pin, do not spread or close legs of firing pin retaining pin.
1.
Remove firing pin retaining pin (2).
2.
Tip key and bolt carrier assembly (5) and catch firing pin (1) as it drops out.
3.
Rotate bolt cam pin (3) one quarter turn and lift straight up to remove.
4.
Remove bolt assembly (4) from key and bolt carrier assembly (5).
END OF TASK
CLEANING
G A S R E L I E F
P O R T S
C A R R I E R K E Y
1 v s 0 7 4
Figure 2. Cleaning of Bolt Carrier Assembly.
Clean carrier key and gas relief ports using CLP (WP 0045, item 9) or RBC (WP 0045, item 12) and pipe
cleaner (WP 0045, item 11).
END OF TASK
0011-2
TM 9-1005-319-23&P
0011
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA
NOTE
There are bolts and bolt carriers on fielded rifles, some with chrome-plated exterior
surface finishes and some with phosphate coating. Both finishes are acceptable
under certain operational requirements and/or restrictions. Phosphate-coated bolt
carriers are required for divisional combat units. Chrome-plated bolt carriers are
acceptable for divisional non-combat units and training center units. Chrome-plated
and phosphate-coated bolt assemblies, bolt carrier assemblies, and repair parts for
these assemblies may be intermixed in any combination, with the following
exception:
Phosphate-coated bolt carriers are required for all deployable and deploying units.
Chrome-plated bolt carriers are acceptable for non-deployable and training center
units.
Air Force Only: Use of chrome-plated or phosphate-coated bolts and bolt carriers
are acceptable for ALL Air Force missions and are deployable. Use of bolt carrier
without forward assist serration is acceptable for ALL Air Force mission
requirements.
2
3
1
6
7
5
4
8
1 v s 0 7 5
Figure 3. Inspection Points.
1.
Inspect bolt assembly (4) to verify that gaps in bolt rings (7) are staggered and approximately 1/3 turn
apart.
2.
Inspect firing pin retaining pin (2) and bolt cam pin (3) for cracks, damage, or excessive wear. Replace
if unserviceable.
3.
Inspect key and bolt carrier assembly (5) for burrs, cracks, wear, and evidence of gas loss. Replace if
unserviceable.
0011-3
TM 9-1005-319-23&P
0011
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA - Continued
4.
Inspect carrier key (6) for dents, distortion, or looseness. If dented or loose, see REPAIR OR
REPLACEMENT in this work package.
5.
Visually inspect the carrier key screws (8) for looseness and proper staking.
NOTE
Do not attempt to re-torque if there is no loosening of the screws indicated by the
staking marks. Surface "A" must not indicate distortion or damage which impairs
parallelism. A maximum of 0.025 in. (0.064 cm) protrusion in an upward direction is
permissible.
S U R F A C E A
S U R F A C E B
0 .0 2 5 M A X
4 P L A C E S
1 v s 0 7 6
Figure 4. Inspection of Carrier Key Screws.
1
9
1 v s 0 7 5 a
Figure 5. Inspection of Firing Pin.
6.
Inspect tip of firing pin (1) for proper contour. Inspect for pitting, wear, and burrs. Pits or wear in area
(9) is permissible. Replace firing pin if defective.
0011-4
TM 9-1005-319-23&P
0011
NOTE
Firing pin should touch the gage on minimum but should not touch on maximum.
1 0
1
4
1 v s 0 7 7
Figure 6. Firing Pin Protrusion Test.
7.
Insert firing pin (1) through bolt assembly (4). Position firing pin protrusion gage (10) P/N 7799735 to
check for proper protrusion of firing pin (minimum 0.028 in. (0.07 cm) to maximum 0.036 in. (0.09 cm)).
Replace defective firing pin.
I N
O U T
4
5
1 v s 0 7 8
Figure 7. Checking for Binding of Bolt Assembly.
8.
Prior to reassembly, insert bolt assembly (4) into key and bolt carrier assembly (5) (do not insert bolt
cam pin) and exercise bolt assembly in and out of key and bolt carrier assembly. Check for binding.
0011-5
TM 9-1005-319-23&P
0011
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA - Continued
5
4
1 v s 0 7 9
Figure 8. Checking for Fit of Bolt Assembly.
9.
Check bolt assembly (4) for proper fit with bolt cam pin removed. Turn key and bolt carrier assembly
(5) and suspend so the bolt assembly is pointed down. The bolt assembly must not drop out. If weight
of bolt assembly allows it to drop out of key and bolt carrier assembly, replace bolt rings (see WP 0012).
END OF TASK
REPAIR OR REPLACEMENT
1 1
5
6
1 v s 0 8 0
Figure 9. Repair of Carrier Key.
0011-6
TM 9-1005-319-23&P
0011
CAUTION
Extreme care must be exercised during the following procedure to ensure that the
striking force is not directed to the attaching screws and that the tube portion is not
enlarged or flared beyond original requirement. Such enlargement would permit loss
of gas pressure when the key and gas tube come together during functioning. The
edge of workbench is recommended.
1.
2.
Repair small dents and/or distortions in carrier key (6) using bolt carrier key tool (11) as follows:
a.
Place the key and bolt carrier assembly (5) in a vertical position, supported so that contact is made
with the rear surface of the carrier key (6).
b.
Insert the small end of the key tool (11) into the tube portion of the carrier key (6).
c.
Strike the large end of the key tool (11) lightly with a 4-ounce, soft-brass hammer.
d.
Repeat striking (gently) until carrier key (6) is reformed to original configuration.
e.
If carrier key (6) cannot be reformed to original configuration, see WP 0013 for replacement.
Replace all authorized unserviceable items. Retest all replaced parts.
END OF TASK
ASSEMBLY
WARNING
Bolt cam pin must be installed or rifle/carbine will blow up while firing the
first round. If the bolt cam pin is not installed, injury to, or death of,
personnel may result.
Unless performed by qualified maintenance personnel, do not interchange
bolt assemblies from one weapon to another. Doing so may result in injury
to, or death of, personnel.
2
3
1
5
4
1 v s 0 7 3
Figure 10. Assembly of Bolt and Bolt Carrier Assembly.
0011-7
TM 9-1005-319-23&P
0011
ASSEMBLY - Continued
1.
Lubricate parts; refer to TM 9-1005-319-10.
NOTE
Before installing bolt assembly, check to see that the bolt ring gaps are staggered to
prevent loss of gas pressure.
2.
Install bolt assembly (4) into key and bolt carrier assembly (5).
3.
Install bolt cam pin (3) and rotate one turn to secure bolt assembly (4).
4.
Hold key and bolt carrier assembly (5) with bolt assembly (4) down and drop in firing pin (1).
5.
Install firing pin retaining pin (2) from left side only to ensure proper installation. Check installation
by attempting to shake out firing pin (1).
END OF TASK
END OF WORK PACKAGE
0011-8
TM 9-1005-319-23&P
FIELD MAINTENANCE
BREECH ASSEMBLY BOLT MAINTENANCE
DISASSEMBLY, CLEANING, INSPECTION — ACCEPTANCE AND REJECTION CRITERIA,
REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Penetrant kit (WP 0045, item 27)
Wiping rag (WP 0045, item 30)
References
TM 9-1005-319-10
WP 0015
Equipment Condition
Bolt assembly removed (WP 0011)
0012-1
0012
TM 9-1005-319-23&P
0012
DISASSEMBLY
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
1
3
2
1 v s 0 8 1
Figure 1. Removal of Cartridge Extractor.
NOTE
Do not separate cartridge extractor and extractor spring assembly unless
replacement of either or both is required.
Do not remove the rubber insert from the extractor spring assembly.
1.
Push out extractor pin (1) and remove cartridge extractor (2) and extractor spring assembly (3) as a
unit.
2.
If required, twist extractor spring assembly (3) counterclockwise to remove from cartridge extractor (2).
4
5
1 v s 0 8 2
Figure 2. Removal of Spring Pin.
0012-2
TM 9-1005-319-23&P
0012
CAUTION
Be sure to use vise jaw protective caps.
3.
Hold bolt (4) in vise and remove spring pin (5) using 1/16 in. punch and hammer.
6
7
1 v s 0 8 3
Figure 3. Removal of Cartridge Ejector.
4.
Remove punch; be sure to catch cartridge ejector (7) and ejector spring (6) to prevent loss.
8
4
1 v s 0 8 4
Figure 4. Removal of Bolt Rings.
NOTE
Do not remove bolt rings unless they require replacement and three new replacement
bolt rings are on hand.
5.
Using flat tip jeweler's screwdriver, remove three bolt rings (8) from bolt (4).
END OF TASK
CLEANING
CAUTION
Do not distort extractor spring assembly during cleaning.
Clean all items; refer to TM 9-1005-319-10. Remove carbon deposits.
END OF TASK
0012-3
TM 9-1005-319-23&P
0012
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA
U N S E R V I C E A B L E
S E R V I C E A B L E
1 v s 0 8 5
Figure 5. Bolt Face Inspection.
1.
Inspect bolt (4) for pits, burrs, and wear as follows:
a.
Bolt faces with a cluster of pits which are touching or tightly grouped, covering an area measuring
approximately 1/8 in. (0.32 cm) across, will be rejected and replaced.
b.
Bolts which contain individual pits or a scattered pattern will not be rejected.
c.
Bolts that contain pits extending into the firing pin hole will not be rejected unless firing pin hole
gaging check determines excess wear.
d.
Rings on the bolt face (machine tool marks), grooves, or ridges less than approximately 0.010 in.
(0.025 cm) will not be cause for rejection.
9
4
1 0
1 v s 0 8 6
Figure 6. Inspection for Cracks in Bolt Assembly.
2.
Inspect bolt (4) for cracks in locking lugs (10) and bolt cam pin hole (9) area. Use black light if
available; otherwise, use a glass of no more than 3X magnification or use a penetrant kit (WP 0045,
item 27). Pay close attention to the area where the locking lugs meet the body. Replace bolt assembly
if bolt is defective.
0012-4
TM 9-1005-319-23&P
0012
WARNING
DRY CLEANING SOLVENT
3.
Use penetrant kit (WP 0045, item 27) to check for cracks in bolt (4) as follows:
a.
The area to be inspected must be clean, free of oil, etc. Spray a small amount of remover on the
area to be inspected, let dry and wipe off with a wiping rag.
b.
Spray penetrant (only enough to wet the area) on the area of the bolt (4) to be inspected.
c.
Spray developer over the penetrant and let the developer work. Cracks will be indicated by a
change in color where there is a crack. If there are cracks, the component is unserviceable.
d.
Pay close attention to the area where the locking lugs (10) meet the body.
e.
If there are no cracks, spray remover on the area; let dry and wipe off with a wiping rag. Oil the
area to prevent corrosion.
f.
Replace bolt assembly if bolt (4) is defective.
1 1
4
1 v s 0 8 7
Figure 7. Inspection of Firing Pin Hole.
NOTE
Bolts with firing pin holes which permit the special no-go plug gage to fully penetrate
at any position on the circumference will be rejected and replaced.
4.
Test bolt (4) for elongated or oversized firing pin hole using special no-go plug gage (11) P/N 12620101.
NOTE
Replacement of the bolt assembly will require that the headspace be tested; see
WP 0015.
END OF TASK
0012-5
TM 9-1005-319-23&P
0012
REPAIR OR REPLACEMENT
8
1
2
3
1 2
6
7
1 v s 0 8 8
Figure 8. Inspection of Bolt Assembly Parts.
1.
Check bolt rings (8) for cracks, kinks, bends, and proper stagger (gaps approximately 1/3 turn apart).
Replace all three bolt rings if one or more bolt rings is damaged.
2.
Inspect cartridge extractor (2), extractor spring assembly (3), and extractor pin (1) for cracks, breaks,
chips, and other damage. Pay close attention to cartridge extractor lip (12). If damaged, replace.
3.
Inspect cartridge ejector (7) and ejector spring (6) for cracks, breaks, and chips. If damaged, replace.
END OF TASK
ASSEMBLY
1.
Lightly lubricate all items; refer to TM 9-1005-319-10.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
WARNING
Unless performed by qualified maintenance personnel, do not interchange
bolt assemblies from one rifle/carbine to another. Doing so may result in
injury to, or death of, personnel.
0012-6
TM 9-1005-319-23&P
0012
4
8
1 v s 0 8 9
Figure 9. Installation of Bolt Rings.
NOTE
To install a bolt ring, carefully place one end in the bolt ring groove and hold in place
with the thumb of one hand. With the index finger of the other hand, gently guide
and push the rest of the bolt ring into the groove a little bit at a time until the entire
bolt ring is in place.
Make certain bolt ring gaps are staggered to prevent loss of gas pressure. New bolt
rings will make installing the bolt assembly difficult. Lubricate inside of key and
bolt carrier assembly and use gentle pressure when installing.
2.
Install three bolt rings (8) one at a time onto the bolt (4) using care not to bend or "spring" new bolt
rings. Stagger the bolt ring gaps (approximately 1/3 turn apart).
5
4
6
7
1 v s 0 9 0
Figure 10. Installation of Cartridge Ejector.
CAUTION
Be sure to use vise jaw protective caps.
3.
Place bolt (4) in a vise and start spring pin (5) in hole.
4.
Install ejector spring (6) and cartridge ejector (7). Align groove on cartridge ejector so that spring pin
(5) can be installed.
0012-7
TM 9-1005-319-23&P
0012
ASSEMBLY - Continued
4
5
6
7
1 v s 0 9 1
Figure 11. Installation of Spring Pin.
5.
Compress and hold ejector spring (6) and cartridge ejector (7) in place with a 3/8 in. punch.
6.
Using hammer and 1/16 in. punch, complete installation of spring pin (5) so that ends are flush with
outside of bolt (4).
3
2
1 v s 0 9 2
Figure 12. Installation of Extractor Spring Assembly.
NOTE
Do not disassemble rubber insert from extractor spring assembly.
7.
If removed, insert large end of extractor spring assembly (3) into cartridge extractor (2) and seat by
pushing and turning clockwise.
0012-8
TM 9-1005-319-23&P
0012
2
3
4
1
1 v s 0 9 3
Figure 13. Installation of Extractor Pin.
8.
Position cartridge extractor (2) and extractor spring assembly (3) on bolt (4).
9.
Compress extractor spring assembly (3) and cartridge extractor (2) to align holes.
10.
Install extractor pin (1) by hand.
END OF TASK
END OF WORK PACKAGE
0012-9/10 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
KEY AND BOLT CARRIER ASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Carrier key screws (2) 8448508
References
TM 9-1005-319-10
WP 0011
WP 0039
Equipment Condition
Key and bolt carrier assembly removed (WP 0011)
DISASSEMBLY
1
2
3
1 v s 0 9 4
Figure 1. Disassembly of Key and Bolt Carrier Assembly.
NOTE
Do not disassemble the key and bolt carrier assembly unless the bolt carrier key is
defective as determined by inspection procedures in WP 0011.
1.
Using socket wrench handle and tight fitting 1/8 in. socket head screw socket wrench attachment,
remove two carrier key screws (1). Discard screws.
NOTE
The heads and part of the bolt carrier key may be ground off in order to remove bolt
carrier key from bolt carrier if carrier key screws cannot otherwise be removed.
2.
Remove bolt carrier key (2) from bolt carrier (3).
END OF TASK
0013-1
0013
TM 9-1005-319-23&P
0013
REPAIR OR REPLACEMENT
Inspect bolt carrier key and bolt carrier. If unserviceable, replace defective parts as authorized in WP 0039.
END OF TASK
ASSEMBLY
1
2
3
1 v s 0 9 5
Figure 2. Installation of Carrier Key.
NOTE
Do not reuse old carrier key screws. New carrier key screws must be used at
assembly.
1.
If disassembled, place bolt carrier (3) in vise using vise jaw caps. Install and position bolt carrier key
(2) on bolt carrier.
2.
Install two new carrier key screws (1).
1
1 v s 0 9 6
Figure 3. Torquing Carrier Key Screws.
3.
Use a tight-fitting 1/8 in. socket head screw wrench attachment and an inch-pound torque wrench to
torque carrier key screws (1) to 50 to 58 in-lb (5.65 to 6.55 N-m).
0013-2
TM 9-1005-319-23&P
0013
1
1 v s 0 9 7
Figure 4. Staking Carrier Key Screws.
0 .0 2 5 M A X
4 P L A C E S
S U R F A C E A
1 v s 0 9 8
Figure 5. Staking Carrier Key Screws in the Field.
NOTE
Field staking method will be used by field units.
4.
Use solid center punch and hand hammer to stake the two carrier key screws (1) in three places.
5.
Reassemble weapon; refer to TM 9-1005-319-10.
NOTE
If blanks are used, blank firing attachment (BFA) must be attached.
6.
If the bolt carrier key is replaced, three to eight rounds of blank or ball ammunition must be fired to
ensure a seal is created. Manual operation of the weapon may be required. Refer to TM 9-1005-319-10
for firing.
END OF TASK
END OF WORK PACKAGE
0013-3/4 blank
TM 9-1005-319-23&P
0014
FIELD MAINTENANCE
CHARGING HANDLE ASSEMBLY MAINTENANCE
DISASSEMBLY, CLEANING, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
References
TM 9-1005-319-10
WP 0039
Equipment Condition
Charging handle assembly removed (WP 0009)
DISASSEMBLY
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
3
1
4
2
2
1 v s 0 9 9
Figure 1. Disassembly of Charging Handle Assembly.
1.
Remove spring pin (1) from charging handle (2) using a hammer and 1/16 in. punch.
2.
As punch is withdrawn, catch charging handle latch (4) and helical spring (3) to prevent loss.
END OF TASK
0014-1
TM 9-1005-319-23&P
0014
CLEANING
Clean all items; refer to TM 9-1005-319-10. Remove carbon deposits.
END OF TASK
REPAIR OR REPLACEMENT
Inspect all items for breaks, cracks, or damage. Replace all unserviceable items as authorized by WP 0039.
END OF TASK
ASSEMBLY
1.
Lightly lubricate all items; refer to TM 9-1005-319-10.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
3
4
1
2
1 v s 1 0 0
Figure 2. Assembly of Charging Handle Assembly.
2.
Position helical spring (3) and charging handle latch (4) in charging handle (2). Align holes and hold in
position.
3.
Install spring pin (1) using hammer. Make sure spring pin is flush.
END OF TASK
END OF WORK PACKAGE
0014-2
TM 9-1005-319-23&P
FIELD MAINTENANCE
UPPER RECEIVER AND BARREL ASSEMBLY (M16A2) 9349050,
(M16A3, M16A4) 12973010, AND (M4, M4A1) 12972680 MAINTENANCE
DISASSEMBLY, CLEANING, INSPECTION — ACCEPTANCE AND REJECTION CRITERIA,
REPAIR OR REPLACEMENT, ASSEMBLY, TEST AND INSPECTION
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Modified needle nose pliers (WP 0030, Figure 7)
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Abrasive cloth (WP 0045, item 13)
Carbon removing compound (WP 0045, item 8)
Chemical and oil protective gloves (WP 0045, item 17)
Dry cleaning solvent (WP 0045, item 15)
Lubricants (WP 0045)
Molybdenum disulfide grease (WP 0045, item 18)
Polyethylene (WP 0045, item 28)
Recessed washer 12991533
Sealing compound (WP 0045, item 32)
Small arms cleaning brush (WP 0045, item 4)
Solid film lubricant (SFL) (WP 0045, item 20)
Target (WP 0045, item 36)
Technical dichloromethane (WP 0045, item 14)
Wash pan (WP 0045, item 26)
References
FM 3-22.9
TM 9-1005-319-10
WP 0016
WP 0017
WP 0018
WP 0019
WP 0020
WP 0039
Equipment Condition
Upper receiver and barrel assembly removed from lower receiver (WP 0009)
0015-1
0015
TM 9-1005-319-23&P
0015
DISASSEMBLY
CAUTION
Do not use a screwdriver or any other tool when removing the handguard assemblies.
Doing so may damage the handguard assemblies and/or slip ring.
Do not remove heat shield for any reason. Doing so will damage the heat shield and
the handguard assemblies will have to be replaced.
NOTE
Refer to TM 9-1005-319-10 for "buddy system" procedure to remove handguard
assemblies.
M16A2 RIFLE ONLY
1
2
1 v s 1 0 1
Figure 1. Removal of Upper Handguard Assembly (M16A2).
1.
Push down on handguard slip ring (2) and lift upper handguard assembly (1) up and out.
0015-2
TM 9-1005-319-23&P
0015
3
2
1 v s 1 0 2
Figure 2. Removal of Lower Handguard Assembly (M16A2).
2.
Push down on handguard slip ring (2) and lift the lower handguard assembly (3) up and out.
M16A3 & M16A4 RIFLE/M4 & M4A1 CARBINE ONLY
2
4
5
6
1 v s 1 0 3
Figure 3. Removal of Upper and Lower Handguards (M16A3/M16A4/M4/M4A1).
3.
Compress handguard slip ring (2) and pivot lower handguard (6) off front retaining clip.
4.
Loosen slotted screw (4) in upper handguard assembly (5). Compress handguard slip ring (2) and
remove upper handguard assembly.
7
8
1 v s 1 0 4
Figure 4. Removal of Barrel Stop Assembly.
5.
Remove barrel stop assembly (7) from barrel assembly (8) (M16A3/M16A4 rifle only).
0015-3
TM 9-1005-319-23&P
0015
DISASSEMBLY - Continued
ALL WEAPONS
1 0
9
1 v s 1 0 5
Figure 5. Removal of Spring Pin.
6.
Using ball-peen hammer and 5/64 in. diameter drive pin punch, drive spring pin (9) (which retains gas
tube) from front sight assembly (10).
1 1
1 2
1 0
1 v s 1 0 6
Figure 6. Removal of Gas Tube.
7.
Slide gas tube (12) back into upper receiver assembly (11) to clear front sight assembly (10). Then lift
slightly, pull forward, and remove gas tube.
0015-4
TM 9-1005-319-23&P
0015
1 3
1 5
1 4
1 7
1 6
1 v s 1 0 7
Figure 7. Removal of Compensator.
8.
Position upper receiver and barrel assembly (14) in barrel removal fixture (13) and secure both in
machinist's vise (17).
9.
Using combination wrench (15), remove compensator (16).
1 4
1 8
1 v s 1 0 8
Figure 8. Removal of Recessed Washer.
10.
Remove recessed washer (18) and discard.
11.
Remove upper receiver and barrel assembly (14) from barrel removal fixture and machinist's vise.
0015-5
TM 9-1005-319-23&P
0015
DISASSEMBLY - Continued
1 5
1 3
1 4
1 9
1 7
1 v s 1 0 9
Figure 9. Loosening of Barrel Nut Assembly.
12.
Place upper receiver and barrel assembly (14) into barrel removal fixture (13) and clamp into
machinist's vise (17).
NOTE
Combination wrench must be pushed toward upper receiver assembly to compress
slip ring spring in barrel nut assembly. Do not use a torque wrench to loosen the
barrel nut assembly.
13.
Using combination wrench (15), loosen barrel nut assembly (19).
8
1 1
1 v s 1 1 0
Figure 10. Separation of Upper Receiver Assembly and Barrel Assembly.
14.
Separate upper receiver assembly (11) from barrel assembly (8).
15.
Remove barrel assembly (8) from machinist's vise and barrel removal fixture (13).
0015-6
TM 9-1005-319-23&P
8
2 1
0015
2
2 2
2 0
2 0
1 v s 1 1 1
Figure 11. Removal of Handguard Slip Ring.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
16.
Remove retaining ring (20) using retaining ring pliers.
17.
Remove slip ring spring (22) and handguard slip ring (2).
18.
Do not remove barrel nut (21) from barrel assembly (8).
END OF TASK
CLEANING
WARNING
CARBON REMOVING COMPOUND
NOTE
A small arms cleaning brush (bore) (WP 0045, item 4) may be used to clean interior
of front sight assembly where gas tube is secured.
Use carbon removing compound (WP 0045, item 8) to remove carbon deposits from interior and exterior of
gas tube. If a large amount of carbon is found and cannot be removed, replace gas tube.
END OF TASK
0015-7
TM 9-1005-319-23&P
0015
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA
2 n d R ib fr o m
R e a r to th e E n d
o f H a n d g u a r d
2 3
2 4
1 s t R ib
F o r w a r d
C r itic a l A r e a
(S h a d e d )
1 v s 1 1 2
Figure 12. Inspection of Handguard Assemblies.
1.
Inspect handguard assemblies for breaks, separation, and cracks using the following guidelines:
a.
Breaks and separations of material which prevent proper retention or interfere with functioning of
the weapon will be cause for handguard assembly rejection and replacement.
b.
M16A2 handguard assemblies may have up to two of the three front retaining tabs (23) missing.
M16A3/M16A4 and M4/M4A1 may not have any front retaining tabs missing. If all front
retaining tabs for the M16A2 are missing, or any of the tabs for the M16A3/M16A4 or M4/M4A1
are missing, handguard assemblies must be replaced.
c.
Cracks up to one inch in length are acceptable provided they do not extend into the retaining flange
(CRITICAL AREA) (24).
d.
Replace severely cracked or damaged handguard assemblies. Handguard assemblies which have a
heat shield which is loose enough to rattle when installed on the weapon must be replaced. If
upper handguard assembly for M16A3/M16A4 rifle is damaged, see WP 0017 for repair. If upper
handguard assembly for M4/M4A1 carbine is damaged, see WP 0018 for repair.
2.
Inspect front sight area for evidence of gas leakage around gas tube. Replace gas tube if short recoil
results from gas leakage.
3.
Inspect gas tube for cracks. Replace if defective.
4.
Inspect the forward assist for slippage or actuation of the pawl. Lubricate in accordance with TM 91005-319-10 if pawl is not actuating. Open the action, pull the bolt and bolt carrier assembly slightly to
the rear, and, with a push or a tap on the forward assist, ensure the bolt is pushed into the locked
position. If forward assist does not perform this function properly, see WP 0019 and WP 0020 for
repair.
0015-8
TM 9-1005-319-23&P
N O T
A C C E P T A B L E
0015
A C C E P T A B L E
1 v s 1 1 3
Figure 13. Bore Inspection.
5.
Inspect bore for burrs, cracks, rust, bulges, and pits using the following guidelines.
a.
Pits no wider than a land or groove and no longer than 3/8 in. (0.95 cm) are allowed in the bore.
b.
Uniformly fine pits in a densely pitted area of the bore are allowable.
c.
Lands that appear dark blue due to coating of gliding metal from projectiles are allowable.
d.
Definitely ringed bores or bores ringed sufficiently to bulge the outside surface of the barrel are
cause for rejection. Replace barrel assembly if defective.
1 0
1 6
2 5
1 v s 1 1 4
Figure 14. Alignment of Compensator.
6.
Hand check compensator (16) for looseness on barrel. Align the third (middle) slot (25) straight up at
top dead center (TDC) in line with front sight assembly (10). The alignment may vary as much as one
half the width of slot in either direction. If loose or out of alignment, repair.
7.
If upper receiver is separated from barrel assembly, inspect chamber for pits utilizing a flashlight. Pits
1/8 in. (0.32 cm) in length are cause for rejection. Replace barrel assembly if defective.
0015-9
TM 9-1005-319-23&P
0015
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA - Continued
2 6
1 v s 1 1 5
Figure 15. Inspection of Chamber.
8.
If upper receiver and barrel assembly is assembled, inspect chamber using reflector tool (26) and
flashlight. Pits 1/8 in. (0.32 cm) in length are cause for rejection. Replace barrel assembly if defective.
If barrel assembly is replaced, inspect headspace. See TEST AND INSPECTION in this work package.
9.
Inspect upper receiver assembly for cracks, corrosion, wear, or damage.
a.
Small dents or gouges that do not affect functioning will not be cause for rejection.
b.
If upper receiver assembly contains cracks or holes, the upper receiver assembly will be replaced.
END OF TASK
REPAIR OR REPLACEMENT
C O R R O D E D
(R E P A R A B L E )
C O R R O D E D
(N O N R E P A R A B L E )
1 v s 1 1 6
Figure 16. Inspection for Corrosion.
1.
Repair corroded upper receiver assembly surface as follows:
a.
Sand corroded area with abrasive cloth (WP 0045, item 13) and make sure all corrosion has been
removed.
0015-10
TM 9-1005-319-23&P
0015
WARNING
DICHLOROMETHANE
b.
Wash area with technical dichloromethane (methylene chloride) (WP 0045, item 14) to remove all
dirt, grease, and foreign material.
c.
Apply sealing compound (WP 0045, item 32), mixed in accordance with manufacturer's directions,
to areas to be filled.
d.
Spread sealing compound as smoothly as possible into defective area using a putty knife or similar
tool.
NOTE
Do not feather edges.
e.
Place a sheet of polyethylene (WP 0045, item 28), cut to size, over filled area. Rub by hand to
smooth.
2.
After curing, remove polyethylene sheet in accordance with instructions from manufacturer.
3.
Wash area with technical dichloromethane (methylene chloride) (WP 0045, item 14) to remove all dirt,
grease, and foreign material.
4.
Roughen area to be refinished with abrasive cloth (WP 0045, item 13) and clean surface again. Do not
touch the area with fingers.
0015-11
TM 9-1005-319-23&P
0015
REPAIR OR REPLACEMENT - Continued
S H I N Y S U R F A C E S
(R E P A R A B L E )
1 v s 1 1 7
Figure 17. Inspection for Shiny Surfaces.
WARNING
SOLID FILM LUBRICANT
CAUTION
Solid film lubricant is to be used only as an exterior surface protective finish and
touchup. If solid film lubricant comes in contact with recoiling parts or functional
surfaces of the weapon, remove immediately by washing with technical
dichloromethane.
5.
Repair shiny surfaces by spraying a coat of solid film lubricant (WP 0045, item 20) in accordance with
instructions supplied by the manufacturer. Dry 24 hours before handling.
6.
Inspect all parts for damage and wear. Replace all defective parts as authorized by WP 0039.
NOTE
Damaged or missing teeth of the barrel nut is not cause for rejection provided the
proper torque value can be obtained during installation using the identified tools. If
removal of the barrel is not possible with the combination tool, a pipe wrench or other
similar tool may be used during removal.
END OF TASK
0015-12
TM 9-1005-319-23&P
0015
ASSEMBLY
8
2 1
2
2 2
2 0
2 0
1 v s 1 1 1
Figure 18. Installation of Handguard Slip Ring.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
NOTE
After cleaning, apply molybdenum disulfide grease (WP 0045, item 18) to threads of
barrel nut assembly before installation.
1.
Position barrel nut (21) by sliding it to the rear of barrel assembly (8) as far as possible.
2.
Slide handguard slip ring (2) over barrel nut (21).
3.
Press slip ring spring (22) from both sides and insert it into handguard slip ring (2).
4.
Install retaining ring (20) against slip ring spring (22) using retaining ring pliers. Snap retaining ring
to barrel nut (21).
0015-13
TM 9-1005-319-23&P
0015
ASSEMBLY - Continued
1 1
M 4
M 1 6 A 3 /M 1 6 A 4 , M 4 /M 4 A 1
2 7
1 1
1 3
8
1 7
M 1 6 A 2
1 v s 1 1 8
Figure 19. Alignment of Barrel Assembly and Upper Receiver Assembly.
NOTE
The alignment pin must not show any signs of looseness.
5.
Position barrel assembly (8) with alignment pin (27) up. Using barrel removal fixture (13), clamp
barrel assembly in vise (17).
NOTE
The slot should fit the alignment pin perfectly with very little or no rotational play
present. Note the play in a new barrel assembly and new upper receiver assembly
and use this as a guide.
6.
Wipe upper receiver threads clean and ensure there are no burrs. Apply molybdenum disulfide grease
(WP 0045, item 18) to the threads before installation.
7.
Align upper receiver assembly (11) using alignment pin (27) and slot in upper receiver assembly.
Install over end of barrel assembly (8).
0015-14
TM 9-1005-319-23&P
0015
1 5
1 1
1 9
1 v s 1 1 9
Figure 20. Torquing of Barrel Nut Assembly.
8.
Engage threads of barrel nut assembly (19) with upper receiver assembly (11).
9.
Using combination wrench (15) and torque wrench, torque barrel nut assembly (19) to 30 ft-lb (40.5
N-m). Torque is measured when both wrenches are used together.
NOTE
Performance of torquing procedure three times provides for a better thread fit and
prevents barrel nut from becoming loose. Do not use the torque wrench for loosening.
10.
Make certain all three drive pins or the teeth on combination wrench are engaged with barrel nut
assembly (19). Loosen and repeat torque operation. Then loosen the barrel nut again.
0015-15
TM 9-1005-319-23&P
0015
ASSEMBLY - Continued
V E R T I C A L
T A R G E T
L I N E
M 1 6 A 2
1 v s 1 2 0
Figure 21. Alignment of Front and Rear Sights.
NOTE
If barrel assembly (usually new) is not properly aligned in upper receiver assembly
(usually an old part), excessive windage will be present and upper receiver assembly
will require replacement to obtain proper fit between alignment pin and slot.
11.
Loosen vise and align bore on a distant vertical target. Center the target in the bore from 12 o'clock
through 6 o'clock. Front sight post should be on line and vertical with the target. Tighten vise. Adjust
rear sight windage until a proper sight picture is obtained on the vertical target. Rear sight aperture
will be approximately in the center of rear sight base if barrel assembly is properly aligned in upper
receiver assembly.
0015-16
TM 9-1005-319-23&P
0015
CAUTION
Do not torque over 80 ft-lb (108 N-m) while tightening barrel nut assembly to next
hole, to allow for proper alignment of gas tube.
NOTE
Do not attempt to hold upper receiver assembly with pry bar; however, if barrel
assembly turns in holding fixture, a pry bar may be used through front sight
assembly base to help prevent barrel assembly from turning in holding fixture. Use
care not to distort or bend front sight assembly or retaining pins. Use "buddy
system" to hold pry bar.
12.
Torque barrel nut assembly (19) again to 30 ft-lb (40.5 N-m) while maintaining sight alignment. Barrel
nut assembly may be tightened beyond 30 ft-lb (40.5 N-m) to align barrel nut assembly serrations for
proper gas tube clearance. Never loosen barrel nut assembly to align for gas tube clearance.
1 1
1 9
1 v s 1 2 1
Figure 22. Alignment of Barrel Nut Assembly.
13.
Check alignment of barrel nut assembly (19) with upper receiver assembly (11). The front 8 in. (20.32
cm) of a gas tube may be used as an alignment tool (see illustration). This is inserted into the bolt
carrier key and then inserted into rear of receiver. If parts of barrel nut assembly are properly aligned,
tool will pass freely and lay top dead center along the top of the barrel. A number 15 twist drill (0.180
in.) may also be used as an alignment tool. If necessary, tighten barrel nut assembly to next hole to
allow proper alignment.
0015-17
TM 9-1005-319-23&P
0015
ASSEMBLY - Continued
8
1 8
1 6
1 v s 1 2 2
Figure 23. Installation of Compensator.
14.
Install new recessed washer (18) with the large diameter of recessed washer forward toward
compensator and the small diameter rearward toward barrel assembly (8).
1 5
8
1 0
1 6
T H I R D
S L O T
2 5
1 v s 1 2 3
Figure 24. Alignment of Compensator.
NOTE
Recessed washer does not require torquing.
15.
Install compensator (16) on barrel assembly (8) using combination wrench (15). Tighten compensator
hand tight and then tighten a minimum of 90 degrees but no more than 450 degrees to align center of
middle slot (25) with post of front sight assembly (10). Tighten compensator to complete alignment
with front sight post to top dead center (TDC). Do not over rotate. If compensator is turned
backwards, the compensator will loosen, so procedure must be started again with a new recessed
washer.
0015-18
TM 9-1005-319-23&P
0015
1 2
1 0
1 9
1 v s 1 2 4
Figure 25. Installation of Gas Tube.
16.
Slide gas tube (12) through barrel nut assembly (19) and then slide forward, inserting gas tube into
hole in base of front sight assembly (10).
1 2
1 0
9
1 v s 1 2 5
Figure 26. Installation of Spring Pin.
17.
Align holes in gas tube (12) and base of front sight assembly (10).
NOTE
To assist in installing spring pin modified nose pliers may be used.
18.
Using ball-peen hammer and 5/64-in. diameter drive pin punch, drive spring pin (9) into base of front
sight assembly (10) to secure gas tube (12).
0015-19
TM 9-1005-319-23&P
0015
ASSEMBLY - Continued
M16A3 & M16A4 RIFLE/M4 & M4A1 CARBINE ONLY
NOTE
Failure to install barrel stop assembly will prevent the M203A2 launcher from being
mounted to the M16A3/M16A4 rifle.
7
8
1 v s 1 0 4
Figure 27. Installation of Barrel Stop Assembly.
19.
Install barrel stop assembly (7) to barrel assembly (8) (M16A3/M16A4 Rifle only). Place barrel stop
over thin section of barrel from six o'clock position, while avoiding contact with gas tube. Rotate barrel
stop so opening is pointed upwards toward gas tube. Slide barrel stop forward until flat vertical
portion fits into triangular sides of forward hand guard cap with springs to rear.
4
2
1 9
5
2 8
1 v s 1 2 6
Figure 28. Installation of Upper Handguard Assembly (M16A3/M16A4/M4/M4A1).
20.
Loosen slotted screw (4). Orient upper handguard assembly (5) so rear-locking clamp (28) is hanging
down, after confirming that arrow on its inner surface points toward muzzle of weapon. Insert front
end of upper handguard assembly into forward handguard cap at an angle. Be sure leaf spring at front
of handguard assembly fits inside lip of handguard cap.
NOTE
M16A3/M16A4 RIFLE ONLY: Ensure notches at front edges of upper handguard
assembly engage tabs at rear edges of barrel stop as handguard assembly is engaged
and lowered into its final position.
21.
Compress rear handguard slip ring (2) and pivot upper handguard assembly (5) down into fully locked
position around barrel nut. Ensure that gas tube slot of rear-locking clamp (28) is straddling gas tube
and that rear legs of clamp slip under barrel nut flange as handguard assembly makes contact with
barrel nut and slip ring.
0015-20
TM 9-1005-319-23&P
22.
0015
Release handguard slip ring (2) and confirm that it slides forward evenly around rear flange of upper
handguard assembly (5). Note that two alignment pins automatically interface with cut-outs in barrel
nut assembly (19) at 10 and 2 o'clock positions to remove rotational play of handguard assembly.
Install and tighten slotted screw (4) to medium tight.
NOTE
Do not remove thermal liner from lower handguard. Orient lower handguard by
confirming that arrow on its inner surface points toward muzzle of weapon.
2
6
1 v s 1 2 7
Figure 29. Installation of Lower Handguard (M16A3/M16A4/M4/M4A1).
23.
Insert front edges of lower handguard (6) into forward handguard cap at angle shown. Compress
handguard slip ring (2) while pivoting lower handguard up and into its final position.
24.
Release handguard slip ring (2) and confirm that it engages around rear flange of lower handguard (6).
M16A2 RIFLE ONLY
NOTE
Refer to TM 9-1005-319-10 for "buddy system" procedure for installing handguard
assemblies.
2 9
1
2
1 v s 1 2 8
Figure 30. Installation of Upper Handguard Assembly (M16A2).
25.
Install top of upper handguard assembly (1) in tube cap (29) while pushing down on handguard slip
ring (2). Push bottom of upper handguard assembly in place and release handguard slip ring to lock
handguard assembly in place.
0015-21
TM 9-1005-319-23&P
0015
ASSEMBLY - Continued
2 9
3
2
1 v s 1 2 9
Figure 31. Installation of Lower Handguard Assembly (M16A2).
26.
Install top of lower handguard assembly (3) in tube cap (29) while pushing down on handguard slip ring
(2). Push bottom of lower handguard assembly in place and release handguard slip ring to lock both
handguard assemblies in place.
END OF TASK
TEST AND INSPECTION
NOTE
The following information pertains to the use of breech, bore, and other gages:
Barrel erosion gage, PN 8448496, can be used to gage all chromed barrels;
Bore straightness gage, PN 8448202, is required for use on all barrels. The gage
must pass through the barrel without being forced.
0015-22
TM 9-1005-319-23&P
0015
M 1 6 A 1 R E J E C T M A R K
3 0
M 1 6 A 2 R E J E C T M A R K
1 v s 1 3 0
Figure 32. Use of Barrel Erosion Gage.
NOTE
When gaging barrel erosion prior to deployment of weapons, use the first mark
(M16A1 Reject Mark) as the preembarkation mark for the M16A2/M16A3/M16A4
Rifles and M4/M4A1 Carbines.
1.
Install key and bolt carrier assembly with bolt assembly and firing pin removed. Hold weapon in
vertical position with receiver up. Insert barrel erosion gage PN 8448496 (30) into rear of upper
receiver assembly. The M16A2 reject mark must be read at rear edge of upper receiver assembly.
NOTE
The M16A2 reject mark will also be used when gaging M16A3/M16A4 rifles and
M4/M4A1 carbines.
2.
If the M16A2 reject mark passes beyond rear surface of upper receiver assembly, the barrel is
unserviceable and shall be replaced.
0015-23
TM 9-1005-319-23&P
0015
TEST AND INSPECTION - Continued
3 1
1 4
1 v s 1 3 1
Figure 33. Use of Bore Straightness Gage.
NOTE
Ensure barrel is clean prior to performing the following test.
3.
Check straightness of bore using straightness gage PN 8448202 (31). Put gage in barrel. Tilt barrel
and allow gage to fall through. Catch gage.
4.
Gage must pass freely through barrel. If gage does not pass through barrel, recheck as follows. Hold
upper receiver and barrel assembly (14) in vertical position with muzzle pointed down; insert gage into
chamber end of barrel. Release gage and catch it as it exits muzzle end. If gage passes freely through
the barrel, barrel is acceptable. If it does not, the barrel must be straightened or replaced. See WP
0016.
0015-24
TM 9-1005-319-23&P
0015
3 2
3 4
3 3
1 1
3 5
1 v s 1 3 2
Figure 34. Insertion of Headspace Gage.
5.
Assemble charging handle assembly (32), bolt assembly (33), and key and bolt carrier assembly (34)
into upper receiver assembly (11).
6.
Insert headspace gage PN 7799734 (35) in chamber.
3 2
3 4
1 1
1 v s 1 3 3
Figure 35. Checking Headspace.
NOTE
For the purpose of this test "light finger pressure" is defined as 8 1/2 to 8 3/4 pounds.
7.
Check headspace by pressing key and bolt carrier assembly (34) and charging handle assembly (32)
forward using light finger pressure.
8.
Bolt should not rotate to locked position. Key and bolt carrier assembly (34) must protrude from rear of
upper receiver assembly (11) for proper headspace.
0015-25
TM 9-1005-319-23&P
0015
TEST AND INSPECTION - Continued
3 6
3 7
3 4
3 2
3 5
1 v s 1 3 4
Figure 36. Use of Weights in Headspace Check.
9.
If the test fails using finger pressure, remove the gage and perform the test again as follows. With the
muzzle down, stack 8 1/2 to 8 3/4 pounds of trigger weights (36) on a locally fabricated spacer/weight
(37) on key and bolt carrier assembly (34). Insert headspace gage (35) and test per above instructions.
10.
Remove trigger weights (36), spacer/weight (37), key and bolt carrier assembly (34), charging handle
(32), and headspace gage (35).
11.
If excessive headspace, first replace bolt assembly and then recheck. If headspace is not corrected,
replace barrel assembly; then recheck with the original bolt to determine if the bolt is still good or if the
bolt should be replaced also.
12.
Remove key and bolt carrier assembly, bolt assembly, charging handle assembly, and headspace gage.
13.
Reassemble weapon; refer to TM 9-1005-319-10.
NOTE
Weapons which have been re-barreled must be function-fired with seven rounds of
5.56mm ball ammunition. After re-barreling, the weapon must be targeted with
three rounds of 5.56mm ball ammunition at 25 meter range using target. Refer to
TM 9-1005-319-10 and FM 3-22.9.
END OF TASK
END OF WORK PACKAGE
0015-26
TM 9-1005-319-23&P
FIELD MAINTENANCE
BARREL ASSEMBLY (M16A2) 9349124, (M16A3, M16A4) 12598107,
REPLACEMENT BARREL AND FRONT SIGHT ASSEMBLY (M4) 9390007,
(M4A1) 12991851 MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Front sight post removal and installation tool (WP 0030, Figure 2)
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Abrasive cloth (WP 0045, item 13)
Chemical and oil protective gloves (WP 0045, item 17)
Dry cleaning solvent (WP 0045, item 15)
Solid film lubricant (SFL) (WP 0045, item 20)
Target (WP 0045, item 36)
References
WP 0015
WP 0039
0016-1
0016
TM 9-1005-319-23&P
0016
DISASSEMBLY
2
1
1 v s 1 3 5
Figure 1. Removal/Installation of Front Sight Post.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
NOTE
Remove front sight post only if parts are damaged.
1.
Using a dummy cartridge or a front sight post removal and installation tool (2) (WP 0030, Figure 2),
remove front sight post (1) by turning counterclockwise.
3
4
1 v s 1 3 6
Figure 2. Removal/Installation of Front Sight Detent and Spring.
2.
Catch front sight detent (3) and helical spring (4) to prevent loss.
0016-2
TM 9-1005-319-23&P
0016
RIFLE ONLY
5
1 v s 1 3 7
6
Figure 3. Removal of Small Sling Swivel (Rifle).
NOTE
Disassemble small sling swivel only if repair is necessary.
3.
If necessary, knock out tubular rivet (6) with a hammer and punch and remove small sling swivel (5).
Discard tubular rivet.
CARBINE ONLY
7
7
1 v s 1 3 8
Figure 4. Removal/Installation of Spring Pins (Carbine).
4.
Remove two spring pins (7).
0016-3
TM 9-1005-319-23&P
0016
DISASSEMBLY - Continued
8
9
1 v s 1 3 9
Figure 5. Removal/Installation of Locking Bar (Carbine).
5.
Lift locking bar (8) up and out of swivel mount (9).
9
1 0
1 v s 1 4 0
Figure 6. Removal/Installation of Swivel Mount (Carbine).
6.
Remove swivel mount (9) from barrel and barrel extension assembly (10).
0016-4
TM 9-1005-319-23&P
0016
5
9
6
1 v s 1 4 1
Figure 7. Disassembly/Assembly of Swivel Mount (Carbine).
7.
Remove tubular rivet (6). Separate small sling swivel (5) from swivel mount (9).
END OF TASK
REPAIR OR REPLACEMENT
1.
Inspect front sight post, front sight detent, and helical spring for damage. If damaged, replace.
2.
Inspect front sight assembly for chips, breaks, and cracks.
1 1
1 1
1 2
1 v s 1 4 2
Figure 8. Repair of Bent Front Sight Assembly.
0016-5
TM 9-1005-319-23&P
0016
REPAIR OR REPLACEMENT - Continued
3.
Inspect front sight guards (11) for bends. Straighten bent front sight guards as follows:
NOTE
Remove spring before heating. (Heat will damage spring.) The sight post and
plunger may be reused unless damaged.
a.
Remove front sight post, detent, and helical spring (see DISASSEMBLY).
NOTE
Use copper or brass caps (jaw inserts) on bench vise to prevent damage to front sight
base during clamping.
b.
Place front sight base (12) in a bench vise.
c.
Heat front sight guards (11) and bend with pliers. The front sight guards should be put back as
nearly as possible to the original position. Allow front sight housing to air cool.
WARNING
DRY CLEANING SOLVENT
d.
Roughen any damaged surface of front sight guards (11) with abrasive cloth (WP 0045, item 13)
and clean with dry cleaning solvent (WP 0045, item 15). Always wear rubber gloves (WP 0045,
item 17) when using dry cleaning solvent.
WARNING
SOLID FILM LUBRICANT
CAUTION
Do not allow solid film lubricant to flow into front sight post threaded well.
4.
e.
Apply solid film lubricant (WP 0045, item 20) to cover the damaged finish.
f.
If front sight guards (11) cannot be straightened utilizing the above procedures, replace the barrel
assembly.
Slightly bent barrels may be straightened as follows:
a.
Check straightness using straightness gage 8448202 (WP 0015). If barrel fails straightness test,
and the gage remains in the barrel in the area of the front sight assembly, perform step b to
determine if it may be straightened.
0016-6
TM 9-1005-319-23&P
b.
0016
With the gage remaining in the bore, hold weapon in a vertical position with end of barrel into
which gage was inserted pointing up. Ensure that if/when gage passes through barrel it will not be
damaged. Using hand pressure ONLY, flex portion of barrel between front sight assembly and
compensator in all four directions (left, right, forward, and back). If barrel is only slightly bent,
gage will drop through when barrel is flexed in one of these directions. Note the direction which
allowed the gage to drop through the barrel.
CAUTION
Remove the gage from the barrel before continuing.
NOTE
If the gage does not pass through the barrel when it is flexed, replace barrel
assembly.
c.
Place barrel in a vise using appropriate protective jaws. Clamp barrel between front sight
assembly and compensator approximately 1 in. (2.54 cm) from front sight assembly. The barrel
assembly should be in a horizontal position with the side noted in step b toward repairman.
CAUTION
Do not apply pressure to the receiver.
5.
d.
Grasp the BARREL near the receiver so that when force is applied the barrel will flex in the same
direction as noted in step b.
e.
Give barrel a sharp jerk of approximately 20 to 40 pounds of force.
f.
Remove barrel from vise and recheck straightness (step a).
g.
If gage still will not pass through barrel, perform step b to determine direction of bend. If barrel is
still bent in the same direction as before, perform steps c through f using slightly more force. If
barrel is now bent in the opposite direction, replace barrel assembly.
h.
If gage passes freely through barrel, barrel shall be considered straight and continue in service.
i.
If barrel has been straightened, the weapon must be targeted (WP 0015).
Replace all unserviceable parts as authorized by WP 0039.
END OF TASK
0016-7
TM 9-1005-319-23&P
0016
ASSEMBLY
RIFLE ONLY
6
5
1 v s 1 4 3
Figure 9. Installation of Small Sling Swivel (Rifle).
1.
If previously disassembled, position small sling swivel (5) and install new tubular rivet (6) using center
punch and hammer to spread and flare the hollow head of the tubular rivet.
CARBINE ONLY
2.
Install small sling swivel (5) to swivel mount (9) with new tubular rivet (6) using center punch and
hammer to spread and flare the hollow head of the tubular rivet.
NOTE
It is recommended that the swivel mount be placed on the left side of the carbine for
right handed operators and on the right side for left handed operators. This will keep
the sling out of the way when the carbine is used. In addition, it shall be oriented so
the integral stop, normally positioned towards the muzzle, is to the rear; this change
in orientation allows the swivel to fold flat towards the muzzle so the side sling
adapter does not interfere with the installation of the rail covers, the forward
handgrip, or other accessories that require installation from the end of the rail.
3.
Install swivel mount (9).
4.
Place swivel locking bar (8) in swivel mount (9).
5.
Install two spring pins (7).
ALL WEAPONS
6.
Position helical spring (4) and front sight detent (3).
0016-8
TM 9-1005-319-23&P
0016
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
7.
Install front sight post (1) by turning front sight post removal and installation tool (2) clockwise until
front sight post base is flush with or slightly below front sight frame.
8.
AIR FORCE ONLY: Perform mechanical zero procedures as follows:
NOTE
This procedure, when used in conjunction with rear sight mechanical zero
adjustment, will give an approximate battle sight zero to most M16A2 rifles. The
following steps can also be used before firing a new or newly assigned rifle. Use the
procedures to check rifles stored in preferred packaging during routine inspections.
This will help ensure soldiers armed with the rifles will have a better chance of
hitting an enemy if the rifles must be used before a live fire zero can be made.
Whenever possible, zeroing of the rifle should be accomplished using ball
ammunition on a 25 meter zeroing target using the "L" aperture.
1 v s 1 4 4
Figure 10. Measurement of Height of Front Sight Post.
a.
Mark a piece of plastic card stock or rigid paper with lines from 1mm to 5mm in 1mm increments.
Set the card on front sight frame and check height of top of front sight post.
0016-9
TM 9-1005-319-23&P
0016
ASSEMBLY - Continued
1 v s 1 4 5
Figure 11. Adjustment of Front Sight Post.
b.
Using a dummy round or front sight post tool, adjust front sight so top of front sight post is 5mm
above machined surfaces of front sight frame.
5 M M
1 v s 1 4 6
Figure 12. Final Measurement of Height.
c.
Visually check front sight post top height by using the marked plastic or paper card. Card must sit
level on machined surfaces of front sight frame to obtain an accurate reading.
END OF TASK
END OF WORK PACKAGE
0016-10
TM 9-1005-319-23&P
0017
FIELD MAINTENANCE
UPPER HANDGUARD ASSEMBLY AND BARREL STOP ASSEMBLY (M16A3, M16A4) MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
EFFECTIVITY NOTICE
M16A3, M16A4 RIFLE
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Spring pin (2) MS16562-223
References
WP 0039
Equipment Conditions
Upper handguard assembly removed from rifle (WP 0015)
Barrel stop assembly removed from rifle (WP 0015)
DISASSEMBLY
1 v s 1 4 7
Figure 1. Placement of Handguard Assembly for Repair.
CAUTION
The handguard assembly is aluminum; therefore, care should always be taken not to
damage or burr the slots of the rails.
NOTE
The spring pins in handguard assembly must be replaced with new pins each time
they are removed.
A good one person method for removal of the spring pins to do repair work is to place
a short piece of 1" x 4" wooden block under the rails. A two person method is to hold
the handguard assembly along the side and over a corner of a wooden work bench.
0017-1
TM 9-1005-319-23&P
0017
DISASSEMBLY - Continued
2
1
3
7
O L D
4
6
5
N E W
1 v s 1 4 8
Figure 2. Disassembly/Assembly of Handguard Assembly.
1.
If damaged, remove slotted screw (2) from upper handguard (3).
2.
Taking care not to damage rails, drive out spring pin (7) using 1/8 in. punch and hammer. Remove rear
handguard clamp (1). Discard spring pin.
3.
Taking care not to damage rails, drive out spring pin (6) using 1/8 in. punch and hammer. Remove
special shaped spacer (5) and flat spring (4). Discard spring pin.
9
8
9
1 v s 1 4 9
Figure 3. Repair of Barrel Stop Assembly.
4.
If damaged, remove two helical compression springs (9) from barrel stop (8) turning counterclockwise
with needle nose pliers.
END OF TASK
0017-2
TM 9-1005-319-23&P
0017
REPAIR OR REPLACEMENT
1.
Clean, inspect, and lubricate the rail surfaces and recoil slots of the upper handguard assembly when
the weapon is cleaned and/or when handguards are being installed.
2.
Use the general purpose brush (M16 rifle double-ended toothbrush) from the standard rifle/carbine
cleaning kit to clean the rail surfaces.
3.
Lightly lubricate upper handguard assembly and spring latches in the handguard.
4.
Remove burrs or nicks from rails using a small stone.
5.
Replace defective items as authorized by WP 0039.
END OF TASK
ASSEMBLY
1.
If removed, install two helical compression springs (9) to barrel stop (8) turning clockwise with needle
nose pliers.
NOTE
The flat spring (WP 0039, Figure 9, item 4) can only be used with the new style
special shaped spacer (PN 13012018).
2.
Install flat spring (4) and special shaped spacer (5) to upper handguard (3). Secure with new spring pin
(6).
3.
Install rear handguard clamp (1) to upper handguard (3) and secure with new spring pin (7).
4.
If removed, install slotted screw (2) to upper handguard (3).
END OF TASK
END OF WORK PACKAGE
0017-3/4 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
UPPER HANDGUARD ASSEMBLY (M4, M4A1) MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
EFFECTIVITY NOTICE
M4, M4A1 CARBINE
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Spring pin (2) MS16562-223
References
WP 0039
Equipment Conditions
Upper handguard assembly removed from carbine (WP 0015)
0018-1
0018
TM 9-1005-319-23&P
0018
DISASSEMBLY
1 v s 1 4 7 a
Figure 1. Placement of Handguard Assembly for Repair.
CAUTION
The handguard assembly is aluminum; therefore, care should always be taken not to
damage or burr the slots of the rails.
NOTE
The spring pins in handguard assembly must be replaced with new pins each time
they are removed.
A good one person method for removal of the spring pins to do repair work is to place
a short piece of 1" x 4" wooden block under the rails. A two person method is to hold
the handguard assembly along the side and over a corner of a wooden work bench.
1
2
3
4
O L D
7
6
5
N E W
1 v s 1 5 0
Figure 2. Disassembly/Assembly of Handguard Assembly.
0018-2
TM 9-1005-319-23&P
0018
1.
If damaged, remove slotted screw (2) from upper handguard (3).
2.
Taking care not to damage rails, drive out spring pin (7) using 1/8 in. punch and hammer. Remove rear
handguard clamp (1). Discard spring pin.
3.
Taking care not to damage rails, drive out spring pin (6) using 1/8 in. punch and hammer. Remove
special shaped spacer (5) and flat spring (4). Discard spring pin.
END OF TASK
REPAIR OR REPLACEMENT
1.
Clean, inspect, and lubricate the rail surfaces and recoil slots of the upper handguard assembly when
the weapon is cleaned and/or when handguards are being installed.
2.
Use the general purpose brush (M16 rifle double-ended toothbrush) from the standard rifle/carbine
cleaning kit to clean the rail surfaces.
3.
Lightly lubricate upper handguard assembly and spring latches in the handguard.
4.
Remove burrs or nicks from rails using a small stone.
5.
Replace defective items as authorized by WP 0039.
END OF TASK
ASSEMBLY
NOTE
The flat spring (WP 0039, Figure 11, item 4) can only be used with the new style
special shaped spacer (PN 13012018).
1.
Install flat spring (4) and special shaped spacer (5) to upper handguard (3). Secure with new spring pin
(6).
2.
Install rear handguard clamp (1) to upper handguard (3) and secure with new spring pin (7).
3.
If removed, install slotted screw (2) to upper handguard (3).
END OF TASK
END OF WORK PACKAGE
0018-3/4 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
UPPER RECEIVER ASSEMBLY AND REAR SIGHT ASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, LUBRICATION,
ASSEMBLY, TEST AND INSPECTION
INITIAL SETUP:
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Index screw 9349065
Solid film lubricant (WP 0045, item 20)
References
TM 9-1005-319-10
WP 0015
WP 0020
WP 0039
Equipment Condition
Upper receiver assembly removed from barrel (WP 0015)
0019-1
0019
TM 9-1005-319-23&P
0019
DISASSEMBLY
ALL WEAPONS
4
3
2
1
1 v s 1 5 1
Figure 1. Removal of Ejection Port Cover.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
NOTE
Headless grooved pin may bind against forward assist housing and require some
additional force to remove.
1.
Remove retaining ring (1) and slide headless grooved pin (4) to the rear.
2.
Catch cover spring (2) and ejection port cover (3) to prevent loss as headless grooved pin (4) is
withdrawn.
0019-2
TM 9-1005-319-23&P
0019
M16A2 RIFLE ONLY
5
8
7
6
1 v s 1 5 2
Figure 2. Removal of Windage Knob.
CAUTION
Be sure to catch small parts. AIR FORCE ONLY: Use magnet to keep from losing
small parts.
3.
Drive out spring pin (5) using a hammer and 1/16 in. punch.
4.
Catch windage knob (8), helical spring (7), and ball bearing (6).
9
1 0
1 2
1 1
1 v s 1 5 3
Figure 3. Removal of Sight Aperture.
5.
Using a flat-bladed screwdriver, remove windage screw (10) from rear sight base (11).
6.
Remove sight aperture (9) and flat spring (12) from rear sight base (11).
0019-3
TM 9-1005-319-23&P
0019
DISASSEMBLY - Continued
1 4
1 3
1 1
2 2
1 5
2 1
1 6
1 7
2 0
1 9
1 8
1 v s 1 5 4
Figure 4. Disassembly of Rear Sight Assembly.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
7.
Drive out spring pin (19) using a 3/32 in. punch. Catch helical spring (18) when punch is withdrawn.
8.
Rotate elevation index (13) until rear sight base (11) clears upper receiver (17). Catch ball bearing (16)
and helical spring (15) as rear sight base clears.
9.
Push elevation index (13) out with thumb using slight rotation motion. Catch ball bearing (21) and
helical spring (20).
10.
Use 1/16 in. key wrench to remove index screw (14). Discard index screw. Separate elevation index
(13) from elevation knob (22) by hand.
0019-4
TM 9-1005-319-23&P
0019
ALL WEAPONS
1 7
2 5
2 4
2 3
1 v s 1 5 5
Figure 5. Removal of Forward Assist Assembly.
11.
Remove spring pin (23) using 3/32 in. drive pin punch and hand hammer.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
12.
Remove forward assist assembly (24) and helical spring (25) from upper receiver (17). For further
disassembly of forward assist assembly see WP 0020.
END OF TASK
REPAIR OR REPLACEMENT
M16A2 RIFLE ONLY
1.
Check rear sight parts for serviceability. Inside of apertures should be round and distinct. Replace if
defective.
2.
Visually inspect rear sight assembly helical springs and ball bearings for breaks, bends, and missing
parts. Ball bearings should be smooth and round. Replace if defective.
3.
Check upper receiver for cracks, corrosion, and damage. Clear drain hole with a piece of wire. Repair
(WP 0015) or replace if defective.
4.
Check that flat spring retains sight aperture firmly in either position. Replace flat spring if sight
aperture is not firm.
5.
Check elevation index and windage knob for legibility of markings. Check underside of windage knob
for cracks. Detent indexing surfaces should be well formed.
6.
Check rear sight base for serviceability. Clear drain holes for springs. Threaded portion of rear sight
base and elevation knob should be well formed.
0019-5
TM 9-1005-319-23&P
0019
REPAIR OR REPLACEMENT - Continued
7.
Inspect rear sight guards for bends; if bent, repair as follows:
NOTE
Ensure that rear sight assembly components are removed from upper receiver.
2 6
2 6
2 7
1 7
1 v s 1 5 6
Figure 6. Straightening Rear Sight Guards.
a.
Place carrying handle (27) in a vise using jaw clamps. Tighten vise to firmly hold upper receiver
(17).
b.
Using two adjustable wrenches, gradually bend guards (26) to straighten. When bending the
guards, gradually bend beyond the straight point as the guard will partially return when bending
pressure is stopped.
c.
After straightening, use a flat file to remove any nicks, kinks, or burrs that remain on the inside of
guards (26).
WARNING
SOLID FILM LUBRICANT
CAUTION
Do not use wire brush on aluminum surfaces.
d.
Apply solid film lubricant (WP 0045, item 20) to brightened area for final protective coating.
e.
If rear sight guards cannot be straightened utilizing the above procedures, replace the upper
receiver.
0019-6
TM 9-1005-319-23&P
0019
ALL WEAPONS
8.
Inspect ejection port cover and latch assembly for serviceability.
9.
Inspect all parts for damage and wear. Replace all defective parts as authorized by WP 0039.
END OF TASK
LUBRICATION
Lubricate upper receiver assembly and rear sight assembly. Apply cleaner, lubricant, and preservative
(CLP) (WP 0045, item 9) to helical springs and ball bearings (three each) and threaded portion of screws
before installation. Lubricate helical springs and ball bearings through their respective drain holes.
END OF TASK
ASSEMBLY
ALL WEAPONS
2 3
1 7
2 5
2 4
1 v s 1 5 7
Figure 7. Installation of Forward Assist Assembly.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
1.
Apply CLP (WP 0045, item 9) to helical spring (25) and forward assist assembly (24) and install them
into upper receiver (17).
2.
Install spring pin (23) using 3/32 in. drive pin punch and hammer.
0019-7
TM 9-1005-319-23&P
0019
ASSEMBLY - Continued
M16A2 RIFLE ONLY
1 4
1 3
2 8
2 2
2 1
1 7
2 0
1 v s 1 5 8
Figure 8. Assembly and Installation of Elevation Knob Assembly.
3.
Assemble elevation knob (22), elevation index (13), and new index screw (14) using 1/16 in. key wrench.
Do not overtighten index screw as scale will require adjustment.
4.
Install ball bearing (21) and helical spring (20) using needle-nose pliers or tweezers.
5.
Depress ball bearing (21) with a punch inserted through access hole, and slide elevation knob assembly
(28) into upper receiver (17) from the side. Center elevation knob assembly.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
NOTE
All springs are identical when new. Once disassembled from the rifle, their free
length may vary due to different amounts of compression when installed. If the
length of springs varies, use longer spring with windage knob and shorter spring in
rear sight base.
0019-8
TM 9-1005-319-23&P
1 1
0019
1 5
1 6
1 7
2 8
1 v s 1 5 9
Figure 9. Installation of Rear Sight Base.
6.
Insert threaded portion of rear sight base (11) into upper receiver (17) and rotate elevation knob
assembly (28) until threads engage.
7.
Insert helical spring (15) and ball bearing (16) into hole as elevation knob assembly (28) is further
rotated and rear sight base (11) is lowered into upper receiver (17). Rotate elevation knob assembly
until rear sight base is all the way down. Then come up 22 clicks before installing spring pin. Check
spring action of helical spring on upper receiver.
0019-9
TM 9-1005-319-23&P
0019
ASSEMBLY - Continued
2 9
1 7
1 9
1 8
2 8
1 8
1 1
1 v s 1 6 0
Figure 10. Installation of Helical Spring.
CAUTION
Ensure that spring pin passes over helical spring, not through its coils.
8.
Insert helical spring (18) through underside of upper receiver (17). Compress helical spring with a
small tip screwdriver (29) to install spring pin (19). Spring pin must pass over helical spring, not
through its coils. Rotate elevation knob assembly (28) until rear sight base (11) is all the way down.
9
1 0
1 2
1 1
5
8
6
7
1 v s 1 6 1
Figure 11. Installation of Sight Aperture and Windage Knob.
0019-10
TM 9-1005-319-23&P
9.
10.
0019
Install flat spring (12) and sight aperture (9) in rear sight base (11). Install windage screw (10) with
screwdriver.
Insert helical spring (5) and ball bearing (6) in windage knob (8).
NOTE
Tilt upper receiver toward windage knob during positioning to prevent loss of ball
bearing.
11.
Position windage knob (8) on shaft of windage screw (10). Align holes in windage knob with hole of
shaft in windage screw. Install spring pin (5).
ALL WEAPONS
1 7
4
3
1
2
1 v s 1 6 2
Figure 12. Installation of Ejection Port Cover.
12.
Position ejection port cover (3) and helical spring (2) on upper receiver (17) with short leg of helical
spring to the rear on inside of ejection port cover.
NOTE
Long leg of helical spring must be positioned and pretensioned before the headless
grooved pin is installed.
13.
Hold short leg of helical spring (2) in this position and turn long leg one half turn (180 degrees) with
fingers of right hand.
14.
Position long leg of helical spring (2) against ejection port cover (3). Hold helical spring and ejection
port cover in this position and install headless grooved pin (4). Check for proper spring tension during
installation of retaining ring (1).
END OF TASK
0019-11
TM 9-1005-319-23&P
0019
TEST AND INSPECTION
1 4
8
1 3
2 2
2 1
2 0
1 v s 1 6 3
Figure 13. Zeroing Elevation Knob.
1.
Rotate and test elevation index (13) and windage knob (8) for ease of functioning.
2.
Inspect elevation knob zero as follows:
a.
Rotate elevation knob (22) counterclockwise until the rear sight assembly is all the way down. If a
whole click is not felt as the rear sight assembly stops, the rear sight assembly has bottomed out
and will not pivot freely.
b.
Position elevation knob (22) back slightly to its last whole click so the rear sight base is under
tension of ball bearing (21) and helical spring (20). The 300 meter mark should align with mark on
left side of upper receiver.
c.
If 300 meter mark is not aligned with mark on receiver, slip range scale in the following manner:
(1)
Position 300 meter mark with mark on receiver.
(2)
Insert a 1/16 in. key wrench through access hole of rear sight base and into index screw (14).
(3)
Loosen index screw (14) three turns and leave wrench in place.
(4)
Rotate lower portion of elevation knob (22) counterclockwise until it stops (range scale should
not have moved). Elevation knob should be positioned on its last whole click.
(5)
Tighten index screw (14) and remove wrench.
(6)
Check for proper setting.
0019-12
TM 9-1005-319-23&P
AIR FORCE ONLY: Perform mechanical zero procedures as follows:
NOTE
This procedure, when used in conjunction with front sight mechanical zero
adjustment, will give an approximate battle site zero to most M16A2 rifles. The
following steps can also be used before firing a new or newly assigned rifle. Use the
procedure to check rifles stored in preferred packaging during routine inspections.
This will help to ensure that soldiers armed with the rifles will have a better chance
of hitting an enemy if the rifles must be used before a live fire zero can be made.
Whenever possible, zeroing of the rifle should be accomplished using ball
ammunition on a 25 meter zeroing target using the "unmarked" aperture.
R
3.
8
5
5
1 v s 1 6 4
Figure 14. Centering Rear Sight.
a.
Center rear sight by moving windage knob (8) in the appropriate direction.
1 0
1 v s 1 6 5
Figure 15. Adjustment of Rear Sight.
b.
Always push in on head of windage screw (10) after making rear sight adjustments.
0019-13
0019
TM 9-1005-319-23&P
0019
TEST AND INSPECTION - Continued
1 v s 1 6 6
Figure 16. Visual Verification.
c.
Visually check rear sight to ensure it is centered after making adjustments. Also, ensure the rear
sight is set in the short-range (0 - 2) position.
4.
Assemble rifle; refer to TM 9-1005-319-10.
5.
After the rifle is assembled, center rear sight, place at the 300 meter mark, and perform the following
check:
a.
While looking at a light background, obtain good sight alignment.
b.
If the hole in the rear sight aperture appears oval instead of round, the rear sight base or upper
receiver should be replaced. To determine which part requires replacement, replace the rear sight
base first. If this does not resolve the problem, replace the upper receiver.
END OF TASK
END OF WORK PACKAGE
0019-14
TM 9-1005-319-23&P
0020
FIELD MAINTENANCE
FORWARD ASSIST ASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, LUBRICATION, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
References
TM 9-1005-319-10
Equipment Condition
Forward assist assembly removed (WP 0019)
DISASSEMBLY
4
2
3
1
5
5
1 v s 1 6 7
Figure 1. Disassembly of Forward Assist Assembly.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
1.
Drive out spring pin (5) using 1/16 in. pin punch and hammer.
2.
Remove forward assist pawl (1), pawl detent (2), and helical spring (3) from plunger assembly (4).
END OF TASK
0020-1
TM 9-1005-319-23&P
0020
REPAIR OR REPLACEMENT
1.
Inspect forward assist pawl (1) for burrs, chips, and cracks. Minor burrs may be removed using fine
files or stones, as required. Do not deform forward assist pawl. Replace if defective.
2.
Inspect pawl detent (2) for burrs and cracks. Minor burrs may be removed using fine files or stones, as
required. Do not deform pawl detent. Replace if defective.
3.
Inspect helical spring (3) for kinks, breaks, and wear. Replace helical spring if defective.
4.
Inspect plunger assembly (4) for wear, burrs, chips, and breaks. Minor burrs may be removed using
fine files or stones, as required. Do not deform plunger assembly. Replace forward assist assembly if
defective.
5.
Inspect spring pin (5) for wear. Replace if defective.
END OF TASK
LUBRICATION
Lubricate helical spring, pawl detent, and forward assist pawl with cleaner, lubricant, and preservative
(CLP) (WP 0045, item 9) before installation.
ASSEMBLY
4
2
5
3
1
1 v s 1 6 8
Figure 2. Assembly of Forward Assist Assembly.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
1.
Install helical spring (3), pawl detent (2), and forward assist pawl (1) into plunger assembly (4).
2.
Align holes and install spring pin (5) using 1/16 in. drive pin punch and hammer. Spring pin must be
flush or slightly below flush after reassembly.
3.
Assemble rifle; refer to page TM 9-1005-319-10.
END OF TASK
END OF WORK PACKAGE
0020-2
TM 9-1005-319-23&P
FIELD MAINTENANCE
LOWER RECEIVER AND BUTTSTOCK ASSEMBLY MAINTENANCE
DISASSEMBLY, INSPECTION — ACCEPTANCE AND REJECTION CRITERIA,
REPAIR OR REPLACEMENT, ASSEMBLY, TEST AND INSPECTION
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Pivot pin installation tool (WP 0030, Figure 4)
Pivot pin removal tool (WP 0030, Figure 3)
Slave pin (WP 0030, Figure 5)
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Lockwasher MS35335-61
Machine screw 9349128
Solid film lubricant (SFL) (WP 0045, item 20)
Technical dichloromethane (WP 0045, item 14)
References
TM 9-1005-319-10
WP 0015
WP 0023
WP 0024
WP 0025
WP 0039
Equipment Condition
Lower receiver and buttstock assembly removed (WP 0009)
0021-1
0021
TM 9-1005-319-23&P
0021
DISASSEMBLY
1
2
5
3
4
1 v s 1 6 9
Figure 1. Removal of Pistol Grip.
1.
Remove machine screw (2) and lockwasher (3). Discard lockwasher.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
2.
Carefully remove pistol grip (1) and catch helical spring (5) and safety detent (4) to prevent loss.
RIFLE ONLY
6
1 v s 1 7 0
Figure 2. Removal of Machine Screw.
0021-2
TM 9-1005-319-23&P
0021
NOTE
If machine screw is removed, it must be discarded and replaced with a new one.
3.
Remove and discard machine screw (6).
7
8
1 1
1 0
9
1 v s 1 7 1
Figure 3. Removal of Buttstock Assembly (Rifle).
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
4.
Remove buttstock assembly (7) carefully and catch helical spring (11), takedown pin detent (10),
takedown pin (9), and stepped spacer (8) to prevent loss.
NOTE
If takedown pin detent will not come out, use a wire to push it out.
0021-3
TM 9-1005-319-23&P
0021
DISASSEMBLY - Continued
CARBINE ONLY
1 2
1 4
1 3
1 v s 1 7 2
Figure 4. Removal of Buttstock Assembly (Carbine).
5.
Extend buttstock assembly (12).
6.
Grasp lock release lever (14) in area of retaining nut (13), pull downward, and slide buttstock assembly
(12) to the rear to separate from lower receiver extension.
1 6
1 5
1 6
1 v s 1 7 3
Figure 5. Removal of Pivot Pin.
0021-4
TM 9-1005-319-23&P
0021
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
NOTE
Air Force Only: Lower receivers without a pivot pin detent are acceptable for use
by Air Force personnel for all mission requirements worldwide. Refer to Air Force
TO 11W3-5-5-24 for National Stock Numbers for replacement pivot pins.
Catch pivot pin detent and helical spring as pivot pin is removed.
7.
Insert fabricated pivot pin removal tool (15) (WP 0030, Figure 3) to compress pivot pin detent. Turn
pivot pin (16) a quarter turn. Remove tool and pivot pin.
1 7
1 8
1 v s 1 7 4
Figure 6. Removal of Detent and Helical Spring.
8.
Catch pivot pin detent (18) and helical spring (17) in cupped hand to prevent loss.
NOTE
If helical spring will not come out, use a wire to pull it out.
0021-5
TM 9-1005-319-23&P
0021
DISASSEMBLY - Continued
1 9
2 0
2 0
2 1
1 v s 1 7 5
Figure 7. Removal of Buffer Assembly and Action Spring.
NOTE
Make sure hammer is cocked and selector lever is not set on BURST or AUTOMATIC
before removing buffer assembly.
9.
Press buffer assembly (20) in about 1/4 in. (0.635 cm). Depress buffer retainer (21) and release buffer
assembly and action spring (19). Remove buffer assembly and action spring from receiver while
depressing buffer retainer.
0021-6
TM 9-1005-319-23&P
2 2
2 2
0021
2 3
2 4
2 5
1 v s 1 7 6
Figure 8. Removal of Bolt Catch.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
10.
Remove spring pin (22) using 3/32 in. drive pin punch and hammer.
11.
Remove bolt catch (23), bolt catch plunger (25), and bolt catch spring (24).
2 6
2 7
2 8
1 v s 1 7 7
Figure 9. Removal of Magazine Catch.
12.
Using drive pin punch, press magazine catch button (27) and turn magazine catch (28)
counterclockwise to unscrew and remove.
13.
Remove magazine catch button (27) and magazine catch spring (26).
0021-7
TM 9-1005-319-23&P
0021
DISASSEMBLY - Continued
2 9
3 0
3 2
3 1
1 v s 1 7 8
Figure 10. Removal of Sear and Selector Lever.
14.
Use a rounded tip drive pin punch to push automatic sear pin (30) from lower receiver and receiver
extension assembly (32).
NOTE
To remove automatic sear, selector lever must be positioned to BURST (if installed).
15.
Remove automatic sear (29) and selector lever (31).
3 3
3 4
3 2
1 v s 1 7 9
Figure 11. Removal of Hammer Assembly.
0021-8
TM 9-1005-319-23&P
0021
NOTE
To remove hammer assembly, place selector lever (if installed) to SEMI position.
16.
Use drive pin punch to push hammer pin (34) from lower receiver and receiver extension assembly (32).
17.
Remove hammer assembly (33). If further disassembly is required, see WP 0023.
3 5
3 6
3 8
3 2
3 7
3 2
4 0
4 1
4 2
3 9
3 9
1 v s 1 8 0
Figure 12. Removal of Trigger Assembly.
NOTE
Use of fabricated slave pin will allow removal of the following parts as a unit.
18.
Remove trigger pin (39) by pushing from the left side of lower receiver and receiver extension assembly
(32) with fabricated slave pin (38) (WP 0030, Figure 5) and a drive pin punch.
19.
Remove semiautomatic disconnector (35), burst disconnector (36), and trigger assembly (37). If further
disassembly of trigger assembly is required, see WP 0024.
M16A3 and M4A1 ONLY
20.
Remove disconnector (41) and trigger assembly (40) with disconnector spring (42) from lower receiver
and receiver extension assembly (32).
END OF TASK
0021-9
TM 9-1005-319-23&P
0021
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA
R I F L E
C A R B I N E
1 v s 1 8 1
Figure 13. Inspection of Buffer Assembly.
1.
Inspect buffer assembly for cracks or damage. The buffer assembly has a hole with pin installed which
protrudes equally on each side approximately 1/32 in. (0.08 cm).
2.
If cracked or damaged, replace.
F R E E L E N G T H
1 v s 1 8 2
Figure 14. Inspection of Action Spring.
3.
Check free length of action spring. RIFLE ONLY: The free length must be between 11 3/4 in. (29.85
cm) minimum and 13 1/2 in. (34.29 cm) maximum. CARBINE ONLY: The free length must be
between 10 1/16 in. (25.56 cm) minimum and 11 1/4 in. (28.58 cm) maximum. If measurements are not
accurate, replace. Do not attempt to adjust the length by stretching the action spring.
0021-10
TM 9-1005-319-23&P
0021
1 v s 1 8 3
Figure 15. Inspection for Serial Number.
4.
Inspect lower receiver and receiver extension assembly (without further disassembly) for legibility of
serial number. ARMY ONLY: If the serial number is hard to read, see WP 0025 for repair. AIR
FORCE ONLY: If the serial number is hard to read, evacuate to depot maintenance.
NOTE
See WP 0015 for repair of corroded surfaces.
5.
Inspect lower receiver for corrosion in lower receiver lobes of pivot area or hinge pin area. If extensive
corrosion appears in these areas, the receiver cannot be repaired; turn in weapon for replacement.
Lower receiver extensions with shiny or corroded surfaces may be repaired. Lower receiver extensions
with thin walls or holes must be replaced.
S H I N Y S U R F A C E S
(R E P A R A B L E )
C O R R O D E D A N D N O H O L E S
(R E P A R A B L E )
S H I N Y S U R F A C E S
(R E P A R A B L E )
C O R R O D E D
(R E P A R A B L E )
S H I N Y S U R F A C E S
(R E P A R A B L E )
C O R R O D E D W I T H H O L E
(N O N R E P A R A B L E )
C O R R
W E
P I V O
(N O N
O D E D
A K E N
T P I N
R E P A R
L O
I N
A R
A B
G
C O R R O D E D
(R E P A R A B L E )
B E S
E A
L E )
T H I N
W A L L S
H O L E S
H O L E S A N D T H I N W A L L
(N O N R E P A R A B L E )
1 v s 1 8 4
Figure 16. Condemnation Criteria.
0021-11
TM 9-1005-319-23&P
0021
INSPECTION — ACCEPTANCE AND REJECTION CRITERIA - Continued
NOTE
If a weapon's lower receiver is missing one third or more of its exterior protective
finish, resulting in an unprotected, light-reflecting surface, it is candidate for
overhaul. This missing finish will be considered a shortcoming. This shortcoming
requires action to obtain a replacement weapon. Once a replacement has been
received, evacuate the original weapon to depot for overhaul.
6.
Inspect for missing or damaged parts. Inspect finish of lower receiver for shiny spots. Touch up with
solid film lubricant (WP 0045, item 20) as required. See WP 0015 for procedure to repair shiny
surfaces.
END OF TASK
REPAIR OR REPLACEMENT
Repair or replace all defective parts of lower receiver and buttstock assembly as authorized by WP 0039.
ASSEMBLY
1.
Clean and remove carbon deposits from all items. Lightly lubricate all metal components. Refer to TM
9-1005-319-10.
3 5
3 6
3 8
3 2
3 8
3 7
3 9
1 v s 1 8 5
Figure 17. Installation of Trigger Assembly (M16A2/M16A4/M4).
2.
Assemble semiautomatic disconnector (35), burst disconnector (36), and trigger assembly (37). Install
as a unit in lower receiver and receiver extension assembly (32) using slave pin (38) (WP 0030, Figure
5).
3.
Install trigger pin (39) using drive pin punch. Push in until flush. Push out slave pin (38).
0021-12
TM 9-1005-319-23&P
0021
M16A3 and M4A1 ONLY
4 1
3 2
4 0
4 2
3 9
1 v s 1 8 6
Figure 18. Installation of Trigger Assembly (M16A3/M4A1).
4.
Install trigger assembly (40), disconnector spring (42), and disconnector (41) into lower receiver and
receiver extension assembly (32).
5.
Install trigger pin (39) using drive pin punch. Push in until flush.
3 3
3 4
3 9
3 9
3 4
1 v s 1 8 7
Figure 19. Installation of Hammer Assembly.
NOTE
Ends of hammer spring are installed to rear of trigger pin (39), resting in the annular
groove on upper surface of trigger pin.
6.
Install hammer assembly (33).
7.
Install hammer pin (34) using drive pin punch. Push in until flush.
0021-13
TM 9-1005-319-23&P
0021
ASSEMBLY - Continued
3 2
2 9
3 0
3 1
1 v s 1 8 8
Figure 20. Installation of Sear and Selector Lever.
NOTE
Hammer assembly should be cocked prior to installing the selector lever.
Selector lever, if installed, must be positioned to BURST. Long leg of automatic sear
spring must rest on top of selector lever.
8.
Install selector lever (31) and automatic sear (29).
9.
Install automatic sear pin (30) (install on the right side) into lower receiver and receiver extension
assembly (32) using drive pin punch. Push in until flush.
2 7
2 6
2 8
1 v s 1 8 9
Figure 21. Installation of Magazine Catch.
0021-14
TM 9-1005-319-23&P
10.
0021
Install magazine catch spring (26) and magazine catch button (27).
NOTE
Drive pin punch should be larger than hole in magazine catch button.
11.
Install magazine catch (28). Push on magazine catch button (27) using drive pin punch and turn
magazine catch clockwise until threaded end of magazine catch is flush with head of magazine catch
button.
2 3
2 2
2 4
2 5
1 v s 1 9 0
Figure 22. Installation of Bolt Catch.
12.
Install bolt catch spring (24), bolt catch plunger (25), and bolt catch (23).
13.
Secure by installing spring pin (22) using 3/32 in. drive pin punch and hammer.
0021-15
TM 9-1005-319-23&P
0021
ASSEMBLY - Continued
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
NOTE
Make sure hammer is cocked and selector lever is not set on BURST before installing
buffer assembly.
1 9
2 0
2 1
1 v s 1 9 1
Figure 23. Installation of Action Spring and Buffer Assembly.
14.
Press action spring (19) and buffer assembly (20) until buffer retainer (21) snaps up and holds them in
place.
1 8
4 3
1 7
1 v s 1 9 2
Figure 24. Installation of Pivot Pin Detent.
0021-16
TM 9-1005-319-23&P
0021
NOTE
Lower receivers without pivot pin detent may be used for all Air Force mission
requirements.
15.
Install fabricated pivot pin installation tool (43) (WP 0030, Figure 4). Insert helical spring (17) and
pivot pin detent (18). Compress pivot pin detent in recess with punch and rotate tool. Remove punch.
4 3
1 6
1 8
1 v s 1 9 3
Figure 25. Installation of Pivot Pin.
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
NOTE
Rounded end of pivot pin detent must be in groove of pivot pin when assembly is
complete.
16.
Position pivot pin (16) and, removing fabricated pivot pin installation tool (43) while maintaining
pressure, slide pivot pin into hole. Rotate pivot pin to receive pivot pin detent (18).
0021-17
TM 9-1005-319-23&P
0021
ASSEMBLY - Continued
8
3 2
7
1 1
1 0
6
9
1 v s 1 9 4
Figure 26. Installation of Buttstock Assembly (Rifle).
RIFLE ONLY
CAUTION
Do not kink helical spring during assembly.
17.
Visually inspect takedown pin (9), takedown pin detent (10), and helical spring (11) before installation.
Install takedown pin with groove toward the rear. Install takedown pin detent and helical spring from
the rear.
18.
Install stepped spacer (8) on lower receiver and receiver extension assembly (32) and carefully slide
buttstock assembly (7) into position to compress helical spring (11).
NOTE
Machine screw, if removed, must be discarded and replaced with a new one.
19.
Install new machine screw (6) to secure buttstock assembly (7).
0021-18
TM 9-1005-319-23&P
0021
CARBINE ONLY
1 2
1 4
1 3
3 2
1 v s 1 9 5
Figure 27. Installation of Buttstock Assembly (Carbine).
20.
Pull down lock release lever (14) in area of retaining nut (13) and reinstall buttstock assembly (12) onto
lower receiver and receiver extension assembly (32).
0021-19
TM 9-1005-319-23&P
0021
ASSEMBLY - Continued
ALL WEAPONS
1
2
5
3
4
3 2
1 v s 1 9 6
Figure 28. Installation of Pistol Grip.
WARNING
Any screw longer than 1 1/8 inch used with enhanced rifle grip part number 9349127
could cause a hazardous situation.
CAUTION
Do not kink helical spring during assembly.
21.
Install safety detent (4), pointed end first, and helical spring (5) into bottom of lower receiver and
receiver extension assembly (32).
NOTE
A portion of the helical spring will fit in a hole in the pistol grip.
When utilizing the enhanced rifle grip (it has a bump between the second and third
finger for a better grip) PN 9349127, rifle grip screw, PN AN501D416-18 (1 1/8 in.) or
AN501D416-16 (1 in.), is authorized to be used with the enhanced grip.
Ensure the washer is in place.
22.
Carefully install pistol grip (1) to compress helical spring (5). Secure pistol grip in place with new
lockwasher (3) and machine screw (2).
0021-20
TM 9-1005-319-23&P
23.
0021
Reassemble weapon; refer to TM 9-1005-319-10.
END OF TASK
TEST AND INSPECTION
1 v s 2 2 0
Figure 29. Use of Thickness Gage.
1.
With the upper receiver attached to the lower receiver, and the pivot pin and takedown pins in place,
perform the following test:
a.
Apply hand pressure to push the upper receiver as far to one side as possible.
b.
Attempt to insert a 0.020 in. thickness gage between the pivot pin lugs of the upper and lower
receivers.
c.
If the thickness gage penetrates to the pivot pin at all accessible locations, repair by replacement of
the upper receiver or replacement of weapon is required.
2.
If weapon fails the above test, remove the upper receiver and install a "NEW" upper receiver and
perform the test again.
3.
If weapon now passes the above test, it shall be considered serviceable and continue in use.
4.
If weapon fails the test with a new upper receiver, this failure shall be considered a shortcoming. This
shortcoming requires action to obtain a replacement weapon. Once a replacement has been received,
evacuate the original weapon to depot for overhaul.
0021-21
TM 9-1005-319-23&P
0021
TEST AND INSPECTION - Continued
S I D E
V I E W
F R O N T
V I E W
0 .0 9 5 I N .
(0 .2 4 C M )
B
B
A
A
0 .0 4 5 I N .
(0 .1 1 C M )
0 .1 4 0 I N .
(0 .3 6 C M )
1 v s 1 9 7
Figure 30. Use of Trigger and Hammer Gage.
NOTE
If the lower receiver is not disassembled, visually inspect for broken or damaged
parts, and to ensure that the hammer and trigger springs are correctly installed
before beginning this test. It is not necessary to disassemble the lower receiver for
the sole purpose of this visual inspection. If broken or damaged parts are found,
disassemble and repair as authorized.
5.
Test two hammer pin holes and two trigger pin holes using no-go plug gage PN 12006472. This test
may be conducted by disassembly of the lower receiver or by pushing the pin far enough to disengage
the end of the pin from the side of the receiver which is being tested. If the lower receiver is not
disassembled and the no-go plug gage enters any hole to first shoulder (A), the lower receiver must be
disassembled and all four holes must be tested again.
6.
Gently insert the no-go plug gage and rotate it 180 degrees. If the no-go plug gage passes into any one
of the four pin holes to the second shoulder (B), the weapon is unserviceable and will be turned in for
replacement.
7.
After completion of gaging operation, visually inspect hammer and trigger springs to ensure proper
location of spring legs.
END OF TASK
END OF WORK PACKAGE
0021-22
TM 9-1005-319-23&P
0022
FIELD MAINTENANCE
BUTTSTOCK ASSEMBLY MAINTENANCE
DISASSEMBLY, CLEANING, REPAIR OR REPLACEMENT, LUBRICATION, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
References
TM 9-1005-319-10
WP 0021
WP 0039
Equipment Condition
Buttstock assembly removed from lower receiver and buttstock assembly (WP 0021)
DISASSEMBLY
RIFLE ONLY
2
1
4
3
1 v s 1 9 8
Figure 1. Removal/Installation of Buttplate.
1.
Remove machine screw (4), small sling swivel (3), and buttplate (1) from buttstock (2).
0022-1
TM 9-1005-319-23&P
0022
DISASSEMBLY - Continued
5
6
1
1 v s 1 9 9
Figure 2. Removal/Installation of Door Assembly.
2.
Push down on plunger (6) and lift door assembly (5) from buttplate (1).
8
5
7
1 v s 2 0 0
Figure 3. Disassembly/Assembly of Door Assembly.
3.
Remove straight pin (8) and separate hinge (7) and door assembly (5).
0022-2
TM 9-1005-319-23&P
0022
CARBINE ONLY
9
1 0
1 1
1 6
1 4
1 5
1 3
1 2
1 v s 2 0 1
Figure 4. Disassembly/Assembly of Buttstock Assembly (Carbine).
4.
Tap out spring pin (12) located in oval slot of self-locking nut (13), using 1/16 in. punch.
5.
Insert index finger into forward end of buttstock (11) and push down on headless shoulder pin (9).
Unscrew self-locking nut (13) and remove lock release lever (14), headless shoulder pin, and helical
spring (10). Remove machine screw (16) and small sling swivel (15).
END OF TASK
CLEANING
RIFLE ONLY: Clean all parts with cleaner, lubricant, and preservative (CLP) (WP 0045, item 9). Use
brush to clean knurled surface of door assembly.
END OF TASK
REPAIR OR REPLACEMENT
1.
Inspect buttstock for cracks using the following guidelines:
a.
Under the following conditions, hairline cracks (no chipped away material allowed) originating
from buttplate end of buttstock are acceptable.
(1)
One hairline crack, not to exceed 1 in. (2.54 cm) in length, per side of buttstock.
(2)
Two additional hairline cracks up to 0.25 in. (0.64 cm) in length, per side of buttstock.
(3)
A total of three cracks per side of buttstock, originating from buttplate end, are allowable.
0022-3
TM 9-1005-319-23&P
0022
REPAIR OR REPLACEMENT - Continued
b.
Cracks in the critical area at the front end of the buttstock are not acceptable and these buttstocks
must be replaced.
2.
While buttplate is installed on rifle, inspect for cracks around the mounting holes. Check for cracks in
excess of 0.25 in. (0.64 cm) in length which extend through the buttplate. Replace if cracked.
3.
Inspect door assembly for cracks, corrosion, stuck plunger, separations on outer face, or other damage.
Replace if defective.
4.
Inspect buttstock for unauthorized markings. M16A2 buttstocks, PN 9349121, with unauthorized
markings may be used under the following conditions:
5.
a.
The only authorized markings are those which are temporary in nature, i.e., paint, tape, etc.
b.
When marking a buttstock, only use temporary markings.
c.
Buttstocks with unauthorized markings that have been stamped into the surface of the buttstock
will not be used.
d.
Unauthorized markings that have previously been scratched, etched, carved, etc. may continue in
use if the marks do not extend into the fiber of the buttstock. Cutting into the fiber of the buttstock
may weaken it.
e.
These marks may be at any location on the buttstock. Unauthorized markings are not desirable.
However, if previously applied, they will be allowed to continue in use due to the cost of the
buttstock.
Replace all unserviceable items as authorized by WP 0039.
END OF TASK
LUBRICATION
Lubricate all metal components; refer to TM 9-1005-319-10.
END OF TASK
ASSEMBLY
RIFLE ONLY
1.
Position hinge (7) on door assembly (5) and install straight pin (8).
2.
Install door assembly (5) into buttplate (1) and press plunger (6) to lock.
3.
Position buttplate (1) and small sling swivel (3) to buttstock (2) and secure with machine screw (4).
NOTE
See WP 0021 for reassembly of buttstock assembly to lower receiver.
0022-4
TM 9-1005-319-23&P
0022
CARBINE ONLY
4.
Insert helical spring (10) onto headless shoulder pin (9).
5.
Insert headless shoulder pin (9) and helical spring (10) into hole on top of buttstock (11), threaded end
first.
6.
Insert index finger into forward end of buttstock (11) and push down on headless shoulder pin (9).
7.
Install lock release lever (14) onto threaded portion of headless shoulder pin (9) protruding through
bottom of buttstock (11).
8.
Screw on self-locking nut (13) until flush with headless shoulder pin (9). Align slot in self-locking nut
with spring pin hole in headless shoulder pin.
9.
Lightly tap spring pin (12) until flush on both sides of self-locking nut (13).
10.
Attach small sling swivel (15) with machine screw (16).
END OF TASK
END OF WORK PACKAGE
0022-5/6 blank
TM 9-1005-319-23&P
0023
FIELD MAINTENANCE
HAMMER ASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Equipment Condition
Hammer assembly removed (WP 0021)
DISASSEMBLY
2
1
3
4
5
6
M 1 6 A 3 /M 4 A 1
M 1 6 A 2 /M 1 6 A 4 /M 4
1 v s 2 0 2
Figure 1. Disassembly of Hammer Assembly.
NOTE
M16A2 burst cam is black. M4 burst cam is nickel colored (shiny).
M16A2, M16A4, and M4: Remove hammer spring (1), burst cam spring (2), and burst cam (3) from
hammer and hammer pin retainer assembly (4). M16A3 and M4A1: Remove hammer spring (5) from
hammer (6).
END OF TASK
REPAIR OR REPLACEMENT
1.
Inspect hammer spring for deformities, breaks, and bends. Pay special attention to the large coil.
Replace hammer spring if defective.
2.
Inspect burst cam spring and burst cam for deformities, breaks, and bends; replace if defective.
3.
Inspect hammer and hammer pin retainer assembly for chips and breaks. Hammer pin should click
home under strong finger pressure. Install hammer pin into hole in hammer to check spring retention
of the hammer pin. Replace hammer and hammer pin retainer assembly if defective.
END OF TASK
0023-1
TM 9-1005-319-23&P
0023
ASSEMBLY
2
1
4
3
6
5
M 1 6 A 3 /M 4 A 1
M 1 6 A 2 /M 1 6 A 4 /M 4
1 v s 2 0 3
Figure 2. Assembly of Hammer Assembly.
NOTE
M16A2 burst cam is black. M4 burst cam is nickel colored (shiny).
Burst cam spring should be assembled with bend to the inside. The large loop of the
hammer spring should be assembled over the burst cam (M16A2/M16A4/M4).
M16A2, M16A4, and M4: Install burst cam (3), burst cam spring (2), and hammer spring (1) on hammer
and hammer pin retainer assembly (4). M16A3 and M4A1: Install hammer spring (5) on hammer (6).
END OF TASK
END OF WORK PACKAGE
0023-2
TM 9-1005-319-23&P
0024
FIELD MAINTENANCE
TRIGGER ASSEMBLY AND TRIGGER SUBASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Bolt carrier key tool (WP 0039, Figure 23, item 12)
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Equipment Condition
Trigger assembly removed (WP 0021)
DISASSEMBLY
1
4
3
2
5
6
M 1 6 A 3 /M 4 A 1
M 1 6 A 2 /M 1 6 A 4 /M 4
1 v s 2 0 4
Figure 1. Disassembly of Trigger Assembly.
NOTE
Do not remove disconnector springs unless required for repair.
M16A2, M16A4, AND M4 ONLY
1.
Remove trigger spring (3) and two disconnector springs (1) from trigger (2).
M16A3 AND M4A1 ONLY
2.
Remove disconnector spring (4) and trigger spring (5) from trigger (6).
END OF TASK
0024-1
TM 9-1005-319-23&P
0024
REPAIR OR REPLACEMENT
1.
Inspect trigger spring for kinks, deformities, and weakness. Replace if defective.
2.
Inspect disconnector springs for deformities, bends, breaks, and weakness. Replace if defective.
3.
Inspect trigger for chips, wear, and cracks. Inspect for damaged searing surface on the trigger nose.
Replace if defective.
END OF TASK
ASSEMBLY
M16A2, M16A4, and M4 ONLY
1
2
1 v s 2 0 5
Figure 2. Installation of Disconnector Springs (M16A2/M16A4/M4).
NOTE
Use bolt carrier key tool (WP 0039, Figure 23, item 12) to install disconnector
springs.
M4 CARBINE ONLY: The semi and burst disconnector springs are not the same.
The semi disconnector spring (left side) is black while the burst disconnector spring
(right side) is nickel (shiny). Ensure that the correct spring is installed on each side
for proper functioning.
1.
Use the following procedure to install two disconnector springs (1) using the bolt carrier key tool:
a.
Secure trigger (2) in soft vise jaws or similar device.
0024-2
TM 9-1005-319-23&P
0024
b.
Place one spring (1) firmly on the tool with large diameter coils outward.
c.
Press spring (1) into recess to solid height.
d.
Hold spring (1) at solid height and slide spring into one of the holes until the punch is flush and
perpendicular with the recess wall.
e.
Turn spring (1) one to two turns opposite of coil winding of the spring.
f.
Discontinue winding when an audible click or snap is heard or felt. This indicates that the spring
is seated.
g.
Hold spring (1) in place when removing the tool to avoid unseating or damaging the spring.
4
3
5
6
M 1 6 A 3 /M 4 A 1
M 1 6 A 2 /M 1 6 A 4 /M 4
Figure 3. Installation of Trigger Spring.
M16A2, M16A4, and M4 ONLY
2.
Install trigger spring (3).
M16A3 and M4A1 ONLY
3.
Install disconnector spring (4) by inserting large end of spring into trigger (6).
4.
Install trigger spring (5) on trigger (6).
END OF TASK
END OF WORK PACKAGE
0024-3/4 blank
1 v s 2 0 6
TM 9-1005-319-23&P
0025
FIELD MAINTENANCE
LOWER RECEIVER AND RECEIVER EXTENSION ASSEMBLY (M16A2) 9349101,
(M16A3) 12012002, (M16A4) 12598102, (M4) 9390011, AND (M4A1) 12972690 MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, ASSEMBLY
INITIAL SETUP:
Tools and Special Tools
Combination wrench (WP 0039, Figure 23, item 10)
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Spanner wrench (WP 0039, Figure 23, item 13)
Materials/Parts
Abrasive cloth (WP 0045, item 13)
Molybdenum disulfide grease (WP 0045, item 18)
Solid film lubricant (SFL) (WP 0045, item 20)
References
WP 0021
Equipment Condition
Lower receiver and receiver extension assembly removed (WP 0021)
DISASSEMBLY
2
1
1
3
1 v s 2 0 7
Figure 1. Removal of Trigger Guard.
1.
Remove spring pin (1) from lower receiver (2) using 1/8 in. drive pin punch and hammer.
2.
Remove trigger guard (3).
0025-1
TM 9-1005-319-23&P
0025
DISASSEMBLY - Continued
RIFLE ONLY
NOTE
Use padding between lower receiver and brass vise jaws. Grip the solid portion of the
lower receiver with brass vise jaws which conform to the shape of the lower receiver
in this area.
4
5
6
7
2
1 v s 2 0 8
Figure 2. Removal of Lower Receiver Extension (Rifle).
3.
Clamp lower receiver (2) in a machinist's vise using vise jaw caps and tighten on solid portion just tight
enough to hold.
WARNING
To avoid injury to your eyes, use care when removing spring-loaded parts.
NOTE
As lower receiver extension is removed, catch buffer retainer and helical spring.
Lower receiver is a serial number controlled item.
4.
Remove lower receiver extension (4) from lower receiver (2) using combination wrench (7) (WP 0039,
Figure 23, item 10). Catch buffer retainer (5) and helical spring (6).
0025-2
TM 9-1005-319-23&P
0025
CARBINE ONLY
NOTE
Use wooden vise jaws in place of brass vise jaw caps.
8
9
1 0
1 1
1 2
1 5
1 4
1 3
2
1 v s 2 0 9
Figure 3. Removal of Lower Receiver Extension (Carbine).
5.
Clamp lower receiver (2) in vise and tighten on solid portion just tight enough to hold.
6.
Loosen round plain nut (9) using spanner wrench (WP 0039, figure 23, item 13). Catch headless
straight pin (14) and helical spring (15).
CAUTION
While performing the following step, care should be taken to restrain the pivot pin
spring and detent.
7.
Loosen round plain nut (9) to allow receiver end plate (10) to disengage from lower receiver (2).
Remove takedown pin (13), buffer retainer (11), and helical spring (12). Unscrew lower receiver
extension (8) from lower receiver.
END OF TASK
0025-3
TM 9-1005-319-23&P
0025
REPAIR OR REPLACEMENT
5
4
6
M 1 6 A 2
1 5
8
1 4
2
M 4
1 3
9
1 0
3
1 v s 2 1 0
Figure 4. Inspection of Components.
1.
Inspect lower receiver extension (4 or 8) for corrosion, dents, and wear. Repair by using abrasive cloth
(WP 0045, item 13) to remove light corrosion. Retouch using solid film lubricant (WP 0045, item 20).
Replace if defective.
2.
Inspect buffer retainer (5) for wear. Replace if defective.
3.
Inspect helical spring (6) for deformities and breaks. Replace if defective.
4.
Inspect lower receiver (2). See WP 0021.
5.
Inspect trigger guard (3) for deformities and check operation of plunger and spring. Replace trigger
guard if defective.
6.
CARBINE ONLY: Inspect receiver end plate (10) and round plain nut (9) for damage. Replace if
damaged.
7.
CARBINE ONLY: Inspect detent (14), helical spring (15), and takedown pin (13) for wear and
deformities. Replace if defective.
0025-4
TM 9-1005-319-23&P
0025
NOTE
AIR FORCE ONLY: Only depot maintenance is authorized to restamp the serial
number on weapon.
ARMY ONLY: Only field maintenance is authorized to restamp serial number.
1 v s 2 1 1
Figure 5. Stamping Serial Number.
8.
ARMY ONLY: If serial number is hard to read on weapon, restamp as follows:
a.
Support the receiver in the stamping area to prevent bending and distortion of the receiver.
b.
Exercise extreme care to restamp the same serial number as the original.
c.
Restamp the serial number the same size as the original serial number.
NOTE
Most rifle/carbine serial numbers are 1/8 in. (0.31 cm) in height, or close enough that
this size is acceptable for such restamping. In the event that a weapon has a serial
number that cannot be reproduced by the use of the die sets contained in the Set D
Field Maintenance Post, Camp, and Station Small Arms Shop Set, local purchase of
an appropriate size die set is authorized.
END OF TASK
0025-5
TM 9-1005-319-23&P
0025
ASSEMBLY
RIFLE ONLY
5
6
2
1 v s 2 1 2
Figure 6. Installation of Buffer Retainer (Rifle).
WARNING
To avoid injury to your eyes, use care when installing spring-loaded parts.
1.
Install helical spring (6) and buffer retainer (5) into lower receiver (2).
H O L D B U F F E R
R E T A I N E R
4
2
1 v s 2 1 3
Figure 7. Installation of Lower Receiver Extension (Rifle).
2.
Lubricate threads of lower receiver (2) and lower receiver extension (4) with molybdenum disulfide
grease (WP 0045, item 18) before reassembly.
3.
Install lower receiver extension (4) into lower receiver (2) while depressing buffer retainer.
0025-6
TM 9-1005-319-23&P
0025
7
4
1 6
2
1 v s 2 1 4
Figure 8. Torquing Lower Receiver Extension (Rifle).
NOTE
Use padding between lower receiver and brass vise jaws. Use vise jaws in vise and
brass vise jaw caps, if available.
4.
Clamp solid portion of lower receiver (2) in a machinist's vise using vise jaws. Grip solid portion of
lower receiver with vise jaws which conform to the shape of lower receiver in this area.
5.
Using combination wrench (7) (WP 0039, Figure 23, item 10) and torque wrench (16), torque lower
receiver extension (4) to 35 to 39 ft-lb (47.25 to 52.65 N-m). Torque is read when both wrenches are
used together.
0025-7
TM 9-1005-319-23&P
0025
ASSEMBLY - Continued
CARBINE ONLY
9
1 1
1 0
1 2
8
1 5
1 4
1 3
2
1 v s 2 1 5
Figure 9. Installation of Lower Receiver Extension (Carbine).
6.
Lubricate threads of lower receiver (2) and lower receiver extension (8) with molybdenum disulfide
grease (WP 0045, item 18) before reassembly.
7.
Place helical spring (12) and buffer retainer (11) into retaining hole of lower receiver (2). Screw round
plain nut (9) onto lower receiver extension (8) with three notches on round plain nut facing forward.
8.
Align receiver end plate (10) onto lower receiver extension (8) with lug of receiver end plate facing
forward.
9.
Place takedown pin (13), headless straight pin (14), and helical spring (15) in lower receiver assembly
(2).
10.
Push down on buffer retainer (11) and helical spring (12) and, at the same time, screw lower receiver
extension (8) in until it retains buffer retainer in position.
11.
Align lug of receiver end plate (10) into rear of lower receiver (2). Screw round plain nut (9) forward
until it contacts receiver end plate.
12.
Using spanner wrench (WP 0039, figure 23, item 13), tighten round plain nut (9) until snug.
13.
Using spanner wrench and torque wrench, torque round plain nut (9) to 38 to 42 ft-lb (51.53 to 56.95
N-m).
14.
Stake receiver end plate (10) in two places across from notches in round plain nut (9).
0025-8
TM 9-1005-319-23&P
0025
ALL WEAPONS
1
3
2
1 v s 2 1 6
Figure 10. Installation of Trigger Guard.
15.
Install trigger guard (3) into lower receiver (2).
16.
Install spring pin (1) using 1/8 in. drive pin punch and hammer.
END OF TASK
END OF WORK PACKAGE
0025-9/10 blank
TM 9-1005-319-23&P
0026
FIELD MAINTENANCE
ADAPTER RAIL COVER ASSEMBLIES MAINTENANCE
REMOVAL, REPAIR OR REPLACEMENT, INSTALLATION
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
References
WP 0039
REMOVAL
1
2
1 v s 2 1 7
Figure 1. Removal/Installation of Rail Cover.
NOTE
Rail covers are quickly detached from the adapter rail. A spring tension clip at one
end of each rail cover automatically engages cutouts positioned at either end of the
four rail sections.
To slide rail cover beyond a cutout, or to remove it, slide rail cover (1) in desired direction while applying
thumb pressure to spring tension clip (2).
END OF TASK
REPAIR OR REPLACEMENT
1.
Use the general purpose brush (M16 rifle double-ended toothbrush) from the standard rifle/carbine
cleaning kit to clean rail covers.
2.
If rail covers are exposed to salt water or corrosive chemicals, thoroughly rinse in fresh water as soon
as the tactical situation allows. Thoroughly clean, inspect, and lubricate spring retaining clips.
3.
Clean and inspect the rail covers and the rail grabbers of accessories to be mounted prior to embarking
on tactical operations or training events.
0026-1
TM 9-1005-319-23&P
0026
REPAIR OR REPLACEMENT - Continued
4.
Rail covers may usually be cleaned with an absorbent cloth. There is no reason to apply lubricant to
the plastic surfaces of the rail covers.
5.
Replace rail cover if not secure. See WP 0039.
END OF TASK
INSTALLATION
NOTE
The rail covers perform two primary functions. They are configured to protect the
shooter's hands from direct skin contact with the metal parts of the adapter rail
which gets hot during extended firing. They also protect the rail surfaces from excess
wear and damage. For these reasons, rail covers should cover the unused sections of
each rail of the adapter rail at all times.
Several different lengths of rail covers are provided with the handguard assemblies.
For ease of reference, they should be identified by the number of ribs along the outer
surfaces, i.e., "11 rib," "9 rib," "5 rib," and "4 rib."
All rail covers are interchangeable between rifles and carbines (carbine set includes
two 2 rib and two 6 rib sections).
1.
To cover the side and bottom rail surfaces, install rail covers (1) from muzzle end of adapter rail.
Longer rail covers on carbine should be oriented with spring tension clip (2) toward muzzle (L-28, R-28,
or B-28). Longer rail covers on rifle should be oriented with spring tension clip toward chamber (L-14,
R-14, or B-14).
2.
To cover the top rail pull charging handle to rear and install rail cover (1) from rear of upper receiver
group.
3.
As spring tension clip (2) meets its cutouts at either end of rails, clip will engage cutouts to secure rail
cover (1). Shorter rail covers (used on rails partially occupied by accessories) should be oriented with
spring tension clip away from accessories.
END OF TASK
END OF WORK PACKAGE
0026-2
TM 9-1005-319-23&P
FIELD MAINTENANCE
ANNUAL GAGING REQUIREMENTS
INSPECTION, GAGING
EFFECTIVITY NOTICE
M16A2 RIFLE
M4, M4A1 CARBINE
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Solid film lubricant (SFL) (WP 0045, item 20)
References
AFI 36-2226
AFTO Form 105
DA PAM 750-8
NAVMC 11003
TB 43-180
TM 1005-319-10
TO 33K-1-100-2
WP 0009
WP 0012
WP 0015
WP 0021
WARNING
To avoid injury to eyes, use care when removing and installing springloaded parts.
Initial gaging is required 1 year from receipt of the weapons.
All rifles and carbines must be gaged at least once annually for safety.
0027-1
0027
TM 9-1005-319-23&P
0027
INSPECTION
NOTE
Inspect M16A2 rifles at least once every 2 years, after the initial inspection/gaging
procedures have been accomplished. This 2 year interval may be maintained unless
preventive maintenance checks and services (PMCS), or other physical evidence,
indicates that an individual unit’s rifles require inspection/gaging at a more frequent
interval. If it is determined that a yearly inspection is necessary for an individual
unit, only that unit will be affected. This will not affect other units in regard to the
interval of inspection.
It is recommended that training units inspect/gage all rifles at the end of each
training cycle. Training units will inspect/gage all rifles at least once annually.
Air Force weapons will be inspected in accordance with the guidance in AFI 36-2226.
1.
Visually inspect general appearance of weapon. Overall appearance will be that of a new weapon. For
inspection criteria see WP 0009. All visual and functional inspection requirements must be met.
2.
Perform a general inspection of weapon per WP 0009. Repair as required and authorized.
NOTE
Small arms gages are precision tools used in the maintenance of Army small arms
and as such should be handled, used and stored with care. Periodically, they should
be cleaned with the authorized cleaning solvent for weapons and given a light coating
of lube. Do not use force when using gages and use them as prescribed in
TM 9-1005-319-10. Per TB 43-180 small arms gages must be turned in for
calibration every 360 days after they are put into use. Air Force will use guidance in
TO 33K-1-100-2, TMDE Calibration Interval Technical Order and Work Unit Code
Reference Guide.
END OF TASK
GAGING
1.
Gage bolt carrier assembly for firing pin protrusion using firing pin protrusion gage PN 7799735 (WP
0044, item 2). See WP 0015.
2.
Gage bolt carrier assembly for firing pinhole wear using no-go plug gage PN 12620101 (WP 0044, item
2). See WP 0012.
3.
Inspect chamber in upper receiver and barrel assembly using chamber reflector tool PN 8448201 (WP
0044, item 2). See WP 0015.
4.
Gage barrel in upper receiver and barrel assembly using barrel erosion gage PN 8448496 (WP 0044,
item 2) and bore straightness gage PN 8448202 (WP 0044, item 2). See WP 0015.
0027-2
TM 9-1005-319-23&P
0027
5.
Check headspace in upper receiver and barrel assembly by inserting headspace gage PN 7799734 (WP
0044, item 2) in chamber. See WP 0015.
6.
Gage pivot pin lug clearance in lower receiver assembly using 0.020-thickness gage. See WP 0021.
7.
Gage hammer and trigger pinholes in lower receiver assembly using taper plug gage PN 12006472 (WP
0044, item 2). See WP 0021.
8.
Gage trigger pull using trigger pull measuring fixture PN 7274758. See WP 0009.
9.
Document inspection with DA PAM 750-8, AFTO Form 105, or NAVMC 11003 when completed.
END OF TASK
END OF WORK PACKAGE
0027-3/4 blank
TM 9-1005-319-23&P
0028
FIELD MAINTENANCE
PREPARATION FOR STORAGE OR SHIPMENT
INITIAL SETUP:
References
MIL-B-117
MIL-B-121
MIL-STD-129
MIL-STD-1186
PPP-B-601
PPP-B-621
PPP-B-636
PPP-B-640
PPP-C-843
PPP-F-320
PPP-T-76
SPI 00-856-6885
PACKAGING
1.
Packaging of the M16A2 Rifle and the M4/M4A1 Carbine shall be in accordance with MIL-STD-129 and
the following:
ARMY ONLY: Army users shall package the rifle and the carbine in accordance with each respective
Packaging Data Sheet (PDS) for shipment or storage which may exceed 90 days. The PDS is part of the
Army Master Data File Retrieval Microform System (ARMS) Packaging File.
AIR FORCE ONLY: Air Force users shall package the rifle in accordance with each respective Special
Packaging Instruction (SPI) 00-856-6885 for shipment or storage which may exceed 90 days. The SPIs are
part of the Army Master Data File Retrieval Microform System (ARMS) Packaging File.
2.
Packaging, if required, for shipping/storage which will not exceed 90 days shall be as follows:
a.
Clean in accordance with operator's manual.
b.
Wrap with MIL-B-121 waterproof material.
c.
Place in barrier bag MIL-B-117, Type I, Class C, or wrap with MIL-B-121, Type I, Grade A, and
seal with tape, PPP-T-76.
d.
Place one or more of item in minimum size container. Block and brace in accordance with MILSTD-1186. Cushion the M16 and similar weight items with PPP-C-843, and use PPP-F-320 as
filler, to create a tight pack.
e.
(1)
Fiber board containers shall be in accordance with PPP-B-636 and may be Class Domestic.
Gross weight and size of material shall determine grade of fiberboard container. PPP-B-640
may also be used.
(2)
Wood containers shall be in accordance with PPP-B-601 or PPP-B-621.
Equivalent materials may be used.
0028-1
TM 9-1005-319-23&P
PACKAGING - Continued
3.
NSNs are not assigned to all the specified material.
END OF TASK
END OF WORK PACKAGE
0028-2
0028
TM 9-1005-319-23&P
0029
FIELD MAINTENANCE
PRE-EMBARKATION INSPECTION OF MATERIAL IN
UNITS ALERTED FOR OVERSEAS MOVEMENT
INITIAL SETUP:
Test Equipment
Tool and Gage Set (WP 0044, item 2)
Materials/Parts
Penetrant kit (WP 0045, item 27)
Solid film lubricant (WP 0045, item 20)
References
AR 725-50
SB 746-1
AMC PAM 310-9
DA PAM 750-8
DA Form 2408-9
WP 0008
WP 0009
WP 0015
NOTE
This work package applies to all the weapons (M16A2, M16A3, and M16A4 Rifle and
M4 and M4A1 Carbine) unless stated otherwise.
PURPOSE
This work package establishes standards for overseas shipment (pre-embarkation inspection criteria) for all
weapons. These standards are provided to ensure that the user is furnished equipment which will perform
its mission without early failure or major maintenance problems.
SCOPE
NOTE
M16 series rifles with chrome plated bolts and bolt carriers, lower receivers without
pivot pin detents, and bolt carriers without serrations may be used by Air Force
personnel for all mission requirements.
1.
The standards prescribed provide for a high percentage of remaining life in affected rifles; therefore,
rifles designated for overseas shipment must qualify under the standards contained in the following
paragraph, table, and in referenced DA publications, before they can be approved for shipping action.
0029-1
TM 9-1005-319-23&P
0029
SCOPE - Continued
2.
Provisions of this standard apply to all US Army agencies/activities selecting or preparing rifles for
shipment to US troops overseas. It also applies to CONUS troops preparing rifles for shipment
overseas. Provisions do not apply either to rifles being prepared for shipment to MAP/MAS recipients
unless specifically prescribed by MAP/MAS transaction for the materiel or to rifle being returned to
CONUS from overseas. The maintenance instructions and standards contained herein do not apply to
rifles once the material has arrived at the overseas destination. At that time, maintenance instructions
contained in the applicable TMs will be used.
3.
This applies to rifles which are the logistic responsibility of the US Army Tank-automotive and
Armaments Command (TACOM).
4.
When inspecting a rifle belonging to another service, the inspector must abide by that service's unique
requirements and that service's exceptions to standard guidance.
GENERAL
1.
Only rifles which have been classified as serviceable condition code A, B, or C under AR 725-50 will be
considered for overseas shipment. All items of equipment for which equipment serviceability criteria
have been published must, as a minimum, be rated green under the ESC as a prerequisite to overseas
shipment. In addition to the condition code standard, as enumerated above, and the required ESC
rating prescribed herein, the rifle being considered for overseas shipment must meet the requirements
of this section. The ESC will be discontinued as new operator manuals are revised which will be used
to determine serviceability condition of rifle.
2.
Waivers to provisions can only be granted by the gaining command of any particular end item being
considered for issue, deployment, or shipment. The issuing services may recommend issue or shipment
of rifles not meeting the provisions when all the following conditions exist:
a.
Repair parts in required quantities cannot be obtained from the supply system prior to delivery of
the end item.
b.
The gaining command concurs in the receipt of the end item for storage until required repair parts
become available. The gaining command must also state that capability, facilities, and funds are
available to perform the necessary work when parts become available.
c.
Department of the Army approval is obtained on a case-by-case basis.
d.
Required repair parts are requisitioned by the issuing command for delivery to the gaining
command.
3.
All Department of the Army MWOs applicable to the specific rifle being considered for shipment overseas must have been applied.
4.
Refer to SB 746-1 for pertinent publications relating to equipment processing and marking information.
5.
Refer to AMC PAM 310-9 for publications containing applicable overhaul standards.
SHIPMENT OR ISSUE
Organizational Repair Parts, Tools, and Equipment
Rifles must be complete with all items required by applicable Department of the Army publications,
including those in the basic issue items list of the appropriate operator's manual.
0029-2
TM 9-1005-319-23&P
0029
Publications
Operator publications applicable to the equipment log book must accompany the equipment. All log book
entries must be complete and up-to-date including those covering any repairs, replacements, or adjustments
made to the rifle in complying with this section.
AIR FORCE ONLY: When a weapon is deployed or shipped to a repair facility for repairs and is expected to
be returned to the owning organization, ensure a copy of each weapon's AFTO Form 105 is processed in
accordance with guidance in TO 11W-1-10 and is sent with the weapon. The original AFTO Form 105 will
remain with the owning organization.
Documentation
Prepare DA Form 2408-9 (Equipment Control Record) at time of overseas shipment or issue to another stock
record or property book account, in accordance with the provisions of DA PAM 750-8.
Preparation
Process rifles for shipment as required by shipping documents and pertinent regulations.
DISPOSITION
Disqualified rifles which do not qualify for shipment will either be redistributed within the camp, post, or
station, be repaired, or become candidates for overhaul, cannibalization, or other disposition as required by
existing regulations.
GENERAL INSPECTION CRITERIA
WARNING
Before starting an inspection, be sure to clear the weapon. Do not pull the
trigger until the weapon has been cleared. Inspect the chamber to ensure
that it is empty and no ammunition is in position to be chambered.
1.
Before inspection, the materiel must be thoroughly cleaned of all grease, dirt, or other foreign matter
that might interfere with its proper function or the use of gages and tools during inspection.
2.
Materiel must be free of burrs, rust, or corrosion on functional surfaces.
3.
Parts must not be cracked, bent, distorted, or damaged and must be free of detrimental wear or
looseness.
4.
Minor defects in metal components do not normally affect their acceptability. For example, scratches
and tool marks are ordinarily of no importance.
5.
Inspect finish of metal surface.
a.
General. Satisfactory metal surfaces for rifles range from black to light gray. A worn shiny metal
surface is objectionable only when it is capable of reflecting light. No rifle will be rejected unless
exterior parts have a shine. All rear sights must have a dull gray or black finish on all surfaces
that would cause a glare.
0029-3
TM 9-1005-319-23&P
0029
GENERAL INSPECTION CRITERIA - Continued
b.
M16A2 Rifle. Minor loss of finish (shiny spots, nicks, scratches) on exterior surfaces of the barrel
and compensator shall not be cause for rejection of M16A2 rifles located in hands of troops at
training centers. Large shiny surfaces, nicks, scratches, etc., can be restored by the use of solid
film lubricant (WP 0045, item 20). Rifles (small arms) missing in excess of one-third or more of the
exterior finish resulting in an unprotected, light-reflecting surface, are considered candidates for
overhaul. The only authorized level of maintenance to phosphate finish small arms is depot.
6.
Plastic components must not be cracked or damaged in such a way as to interfere with their structural
strength. Surface cracks, bruises, or dents that do not affect their strength will not be cause for
rejection. Cracks will be cause for rejection. Criteria for determining which cracks are repairable are
in WP 0008.
7.
Barrels must be clean and free of corrosion such as that caused by moisture and powder fouling.
Standards of serviceability are indicated in paragraphs 7.a. through 7.i. below.
a.
Pits in the chamber are allowable if they do not cause extraction difficulties.
b.
Pits as wide as a land and 3/8 in. (0.95 cm) or less in length are allowable for 5.56 mm barrels. Pits
not greater than the width of a land and less than 3/8 in. (0.95 cm) long are permissible.
c.
Scattered or uniformly fine pits, or fine pits in a densely pitted area are allowable.
d.
Tool marks are acceptable regardless of length. They will appear as lines running laterally in the
grooves, or may run spirally across the top of lands.
e.
Ringed bores or bores ringed sufficiently to bulge the outside surface of the barrel are cause for
rejection. However, faint rings or shadowy depressions do not indicate an unserviceable barrel and
will not be cause for rejection. Gap in lined barrels will not be classified as a ringed bore.
f.
Lands that appear dark due to coating of gilding metal from projectiles will not be cause for
rejection.
g.
Breech bore diameter will be checked on unlined barrels using the appropriate breech bore gage.
h.
Barrel erosion gages are provided for lined barrels. Bore wear will be checked using barrel erosion
gage for the M16A2. For detailed instructions in the use of the above gage and for serviceability
limits, see WP 0015. The M16A1 reject mark will be used to reject worn barrels during preembarkation inspection.
i.
Flaking or checking (fine cracks) of chromium plate in barrels or chambers will not be cause for
rejection, unless accompanied by pitting to the degree that extraction difficulties are encountered
or accuracy is unacceptable.
8.
Springs must be free of distortion and broken coils. Springs must have sufficient tension to perform
their intended function.
9.
Screw heads must be in serviceable condition and threads must not be stripped. Internal threads must
not be stripped.
0029-4
TM 9-1005-319-23&P
0029
10.
The sear, hammer, and/or cocking notches must be in good condition. Chipped engaging corners will be
cause for rejection. Slight wear on functional surfaces, including engaging corners, shall be acceptable,
providing the minimum trigger pull requirements and selector lever checks are met in accordance with
instructions in WP 0009.
11.
Chips, flat spots, or bent striker points on firing pins will be cause for rejection.
12.
The cartridge engaging surfaces on extractors must not be chipped or deformed.
13.
Evidence of any damage to sights will be cause for a sight alignment check. Rear sight bases should
have no movement.
14.
Rear sight elevating and windage mechanisms must operate with distinct clicks, without binding.
Sights must have sufficient tension to retain their setting during firing. Graduations and numerals
must be legible. Graduation filler is not required.
15.
Safeties must positively position in both the ON and OFF position. When in the ON or safe position,
the rifle must not fire when the trigger is squeezed; when in the OFF or fire position, the rifle must fire
when the trigger is squeezed.
16.
All locking devices such as latches, magazine latches, or detents must be positive in action and must
not become disengaged due to normal handling and firing. Retaining pins and similar devices must not
be subject to accidental loss during use or transportation.
17.
Each rifle must be hand functioned to check for unusual binding, positive cocking action, and general
operation. Dummy ammunition must be used to assure positive feeding, chambering, extraction, and
ejection action.
Table 1. 5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine.
Item
Standard
RIFLE:
General .................................... Clear rifle of any ammunition and inspect in accordance with General
Inspection Criteria.
Barrel and barrel extension ... Check barrel erosion. Use barrel erosion gage 8448496 for chrome lined
barrels. Stripping of lands and grooves shall not be cause for rejection
unless so determined by barrel erosion gage.
Visually inspect, using chamber reflector tool 8448201.
Pits 1/8 in. (0.31 cm) in length and those pits large enough to extend from the
body of the chamber into the shoulder stop area and forcing cone area are
cause for rejection. Large pits are defined as 1/8 in. (0.31 cm) or more in
diameter as determined by visual inspection. Only closed flash suppressors
are acceptable.
Check barrel for straightness using bore straightness gage 8448202. Gage
must pass freely through the bore to be acceptable, either dropped from the
muzzle or chamber end.
0029-5
TM 9-1005-319-23&P
0029
GENERAL INSPECTION CRITERIA - Continued
Table 1. 5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine - Continued.
Item
Standard
Front sight and gas tube ........ Inspect gas tube for proper alignment with carrier key. Gas tube must not
bind when mating with the key.
Evidence of gas leaks around the front sight connection of the gas tube shall
be cause for rejection until rifle has been function fired to determine if the
loss of gas is sufficient to cause malfunction. If malfunctions occur during
function firing, repairs are necessary.
Inspect front sight for damage.
Bolt carrier group.................... Inspect bolt for elongated or oversized firing pin hole using plain cylinder
gage 12620101.
Firing pin holes which permit the plain cylinder plug gage to fully penetrate
at any position on the circumference will be rejected.
Bolt face with a cluster of pits which are touching or tightly grouped, covering
an area measuring approximately 1/8 in. (0.31 cm) across will be rejected.
Bolts which contain pits extending into the firing pin hole will not be rejected
unless firing pin hole gaging check determines rejection.
Bolts which contain individual pits or scattered pits will not be cause for
rejection.
Only phosphated bolt carriers are acceptable. Both phosphated and chrome
plated bolts are acceptable for Air Force use; only phosphated bolts are
acceptable for Army use.
NOTE
(Air Force Only)
Use of non-serrated bolt carriers is acceptable for all mission requirements. Use of
chrome plated bolts and/or bolt carriers are acceptable for all mission requirements.
Use of any style extractor spring is acceptable for all mission requirements, replace
extractor spring only when they no longer enable extraction of cartridges.
0029-6
TM 9-1005-319-23&P
0029
Table 1. 5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine - Continued.
Item
Standard
Bolt locking lugs and bolt pin
cam hole. ............................... Inspect for cracks in the locking lugs and cam pin hole area. Use a black
light, if available; otherwise, use a glass of no more than 3X magnification
or use inspection penetrant. Use instructions contained in inspection
penetrant kit for application. If cracks are detected, the bolts will be
replaced.
NOTE
Particular attention must be given to the area where
the lugs meet the bolt body and around the side walls
of the cam pin hole.
Bolt rings must not be broken. Ring gaps must be properly spaced
approximately 1/3 turn apart and not in line.
Firing pin protrusion must be not less than 0.028 in. (0.071 cm) or more than
0.036 in. (0.091 cm). Use firing pin protrusion gage 7799735.
Socket head cap screws must be staked.
Carrier key must not be dented where end mates with gas tube. Repair or
replace damaged carrier keys.
Headspace .............................. Inspect headspace using headspace gage 7799734. Excessive headspace will
be cause for rejection.
Trigger pull ............................ Inspect trigger pull using trigger measuring fixture 7274758. Trigger pull
must be 5.5 lb (2.49 kg) minimum. Maximum for M16A2, M16A4 and M4 is
9.5 lb (4.31 kg). Maximum for M16A3 and M4A1 is 8.5 lb (3.86 kg). Test
trigger pull (see WP 0009).
Lower receiver group............. Inspect hammer and trigger pin holes using plain cylinder plug gage
12006472. Penetration of the gage in any one or more of the four holes will
be cause for rejection.
Inspect for cracks, corrosion, or mutilation which would affect functioning.
Small dents or gouges will not be cause for rejection.
Inspect receiver for corrosion in the lobes of the pivot or hinge pin area.
Width between lobes shall not exceed 0.515 in. (1.30 cm).
Inspect receiver for break through of metal.
Inspect receiver and receiver extension for initial loss of protective coating.
NOTE
Lower receivers without pivot pin detent may be used
for all Air Force mission requirements.
Action spring ........................... M16A2/M16A3/M16A4 Rifle only:
Free length of spring shall be between 11-3/4 and 13-1/2 in. (29.84
and 34.29 cm).
M4/M4A1 Carbine only:
Free length of spring shall be between 10-1/16 and 11-1/4 in.
(25.56 and 28.58 cm).
0029-7
TM 9-1005-319-23&P
0029
GENERAL INSPECTION CRITERIA - Continued
Table 1. 5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine - Continued.
Item
Standard
Handguard .............................. Inspect handguard assembly for breaks, separations, and cracks. Breaks and
separations of material which prevent proper retention or interfere with
functioning of the weapon will be cause for handguard rejection and
replacement. Cracks up to 1 in. (2.54 cm) in length are acceptable provided
they do not extend into the handguard retaining flange (critical area).
M16A2 Rifle only:
Each handguard assembly may have up to two of the three front retaining
tabs missing. If all three front tabs are missing, the handguard assembly
must be replaced.
M16A3/M16A4 Rifle and M4/M4A1 Carbine only:
Inspect per item 3 in Preventive Maintenance Checks and Services (WP
0008).
All weapons:
Replace severely cracked handguards. Handguards that have a heat shield
loose enough to rattle when installed on the weapon must be replaced.
Stock assembly........................ Inspect buttstock assembly for dents, cracks, and chips. Check for breaks
and separation of material which could prevent proper functioning of
weapon.
2
1
2
Figure 1. Buttstock Inspection.
0029-8
1 v s 2 9 8
TM 9-1005-319-23&P
0029
Table 1. 5.56mm Rifle M16A2/M16A3/M16A4, M4/M4A1 Carbine - Continued.
Item
Standard
M16A2 Rifle only:
Under the following conditions, hairline cracks (1) originating from buttplate
end of buttstock are acceptable. No chipped away material is allowed.
a. One hairline crack, not to exceed 1 in. (2.54 cm) in length, per side of
buttstock.
b. Two additional hairline cracks up to 0.22 in. (0.55 cm) in length, per side
of buttstock.
Buttstocks with unauthorized markings stamped into their surfaces will be
replaced. Unauthorized markings, scratched, etched, carved, etc., are
acceptable if they do not extend into the fiber of the buttstock which may
weaken it. These marks may lie at any location on the buttstock.
Cracks (2) in the critical area at the front end of the buttstock are not
acceptable and these buttstocks must be replaced.
M16A3/M16A4 Rifle and M4/M4A1 Carbine only:
Inspect for proper functioning. Repair as required.
END OF WORK PACKAGE
0029-9/10 blank
TM 9-1005-319-23&P
0030
FIELD MAINTENANCE
ILLUSTRATED LIST OF MANUFACTURED ITEMS
INITIAL SETUP:
Not Applicable
INTRODUCTION
Scope
This work package includes complete instructions for making items authorized to be manufactured or
fabricated at the field maintenance level.
How to Use the Index of Manufactured Items
A part number index in alphanumeric order is provided for cross-referencing the part number of the item to
be manufactured to the page which covers fabrication criteria.
Explanation of the Illustrations of Manufactured Items
All instructions needed by maintenance personnel to manufacture the item are included on the illustrations.
All bulk materials needed for manufacture of an item are listed by part number or specification number in a
tabular list on the illustration.
INDEX OF MANUFACTURED ITEMS
Part
Number
NPN
NPN
NPN
NPN
NPN
NPN
NPN
Nomenclature
Front sight detent depressor
Front sight post removal and installation tool
Pivot pin removal tool
Pivot pin installation tool
Slave pin
Adapter bar for M12 arms rack
Modified needle nose pliers
0030-1
Figure
Number
1
2
3
4
5
6
7
TM 9-1005-319-23&P
0030
ILLUSTRATIONS OF MANUFACTURED ITEMS
± 0 .0 2 (0 .0 5 )
0 .0 8 0 (0 .2 0 3 ) D I A
S T K W I R E
± 0 .0 1 (0 .0 3 )
R
1 .2 5 ± 0 .0 3
(3 .1 8 ± 0 .0 8 )
0 .6 2 5 ± 0 .0 2 0 R
(1 .5 8 8 ± 0 .0 5 1 )
0 .7 5 ± 0 .0 5
(1 .9 1 ± 0 .1 3 )
F A B R I C A T E F R O M 0 .0 8 I N . M U S I C W I R E O R E Q U I V A L E N T .
F I N I S H : N O . 5 .3 .1 .2 O R 5 .3 .2 .2 O F M I L -S T D 1 7 .
N O T E : A L L D I M E N S I O N S S H O W N A R E I N I N C H E S
W I T H M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N
P A R E N T H E S E S .
1 V S 2 9 1
Figure 1. Front Sight Detent Depressor.
0030-2
TM 9-1005-319-23&P
4
(1 0 .1 6 )
0030
3 /3 2
(0 .2 4 )
5 /1 6 I N C H
D R I L L T I P
0 .3 6 8
(0 .9 3 )
2
5 /1 6
(0 .7 9 )
(5 .0 8 )
F O U R E Q U A L L Y S P A C E D
T E E T H
1 /8
(0 .3 2 )
1 /1 6
(0 .1 6 )
5 /1 6
(0 .7 9 )
0 .0 7 0 I N . (0 .1 8 C M ) W I D E
F A B R I C A T E F R O M 0 .3 7 5 I N . R O U N D M E T A L B A R ,
A S T M A 6 8 6 , F S C M 8 1 3 4 6 , G R A D E C , C L A S S W 2 -0 9 ,
N S N 9 5 1 0 -0 0 -6 4 0 -4 4 0 7 O R E Q U I V A L E N T .
N O T E
1 . A L L
W I T H
2 . T E E
S :
D I M E N S I O N S S H O W N A R E I N I N C H E S
M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N P A R E N T H E S E S .
T H M U S T B E H A N D F I L E D T O F I T F R O N T S I G H T P O S T .
Figure 2. Front Sight Post Removal and Installation Tool.
0030-3
1 V S 2 9 2
TM 9-1005-319-23&P
0030
ILLUSTRATIONS OF MANUFACTURED ITEMS - Continued
1 /4
(0 .6 4 )
F A B R I C A T E F R O M 1 /1 6 I N . S O C K E T H E A D
N S N 5 1 2 0 -0 0 -1 9 8 -5 3 9 8 O R E Q U I V A L E N T .
S C R E W
N O T E : A L L D I M E N S I O N S S H O W N A R E I N I N C H E S
W I T H M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N
K E Y ,
P A R E N T H E S E S .
1 V S 2 9 3
Figure 3. Pivot Pin Removal Tool.
0030-4
TM 9-1005-319-23&P
0030
2 .5 0 ± 0 .0 5
(6 .3 5 ± 0 .1 3 )
2 5 0
6 3
1 1 /2 (3 .8 1 ) M I N
A
0 .0 0 5 (0 .0 1 3 ) M A X B O W
F O R
A
L E N G T H
1 /8 (0 .3 1 8 )
1 .5 0 - 0 .0 5
(3 .8 1 - 0 .1 3 )
A
A
0 .2 5 ± 0 .0 5 R
(0 .6 4 ± 0 .1 3 )
B
0 .0 1 (0 .0 2 5 ) R M A X O R
0 .0 1 (0 .0 2 5 ) x 4 5 M A X C H A M F E R
0 .2 4 5 + 0 .0 0 0 D I A S T O C K
-0 .0 0 4
(0 .6 2 2 + 0 .0 0 0 )
-0 .0 1 0 )
S E C T I O N
B
A -A
0 .0 0 5 (0 .0 1 3 )
T O T A L
0 .0 9 8 + 0 .0 4 D I A T H R U
-0 .0 0
(0 .2 4 9 + 0 .1 0 )
-0 .0 0 )
F A B R I C A T E F R O M 0 .2 4 5 I N . S T E E L A I S I 1 0 9 5 O R E Q U I V A L E N T .
H A R D E N A N D T E M P E R T O R C 5 7 -6 1 F O R L E N G T H -A F I N I S H : N O . 5 .3 .1 .2 O R 5 .3 .2 .2 O F M I L -S T D -1 7 1 .
N O T E : A L L D I M E N S I O N S S H O W N A R E I N I N C H E S
W I T H M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N
P A R E N T H E S E S .
1 V S 2 9 4
Figure 4. Pivot Pin Installation Tool.
0030-5
TM 9-1005-319-23&P
0030
ILLUSTRATIONS OF MANUFACTURED ITEMS - Continued
V IE W
A
0 .6 2 5
(1 .5 8 8 )
V IE W
B
0 .1 5 4 0 - 0 .0 0 0 5
(0 .3 9 1 2 - 0 .0 1 2 7 )
0 .6 2 5
(1 .5 8 8 )
F A B R I C A T E F R O M O L D T R I G G E R P I N (V I E W A ) P N 8 4 4 8 6 0 9 O R
F A B R I C A T E S L A V E P I N (V I E W B ) F R O M M A T E R I A L B L O C K ,
W I R E , S T E E L A L L O Y , G R A D E 4 1 4 0 , A S T M -A 5 4 7 O R E Q U I V A L E N T .
N O T E : A L L D I M E N S I O N S S H O W N A R E I N I N C H E S W I T H
M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N P A R E N T H E S E S .
Figure 5. Slave Pin.
0030-6
1 V S 2 9 5
TM 9-1005-319-23&P
3 5 7 /8
(9 1 .1 2 )
1 1 /4
(3 .1 7 5 )
0030
1 /8
(.3 2 )
1 1 /4
(3 .1 7 5 )
4 5 °
4 5 °
1 1 /2
(3 .8 1 )
1 1 /2
(3 .8 1 )
F A B
A N G
P A I N
8 0 1 0
R I C
L E
T
-0 1
A T E
I R O N
W I T H
-3 5 0 -5
F R O
, N
O L
2 4 9
M 1 1
S N 9 5
I V E D
O R E
/2
2 0
R
Q
I N
-0 0
A B
U I V
. B Y
-2 7 7
E N A
A L E
1 1 /2 I N . B Y 1 /8 I N .
-4 9 0 2 O R E Q U I V A L E N T .
M E L P A I N T , N S N
N T .
N O T E : A L L D I M E N S I O N S S H O W N A R E I N I N C H E S W I T H
M E T R I C C O N V E R S I O N T O C E N T I M E T E R S I N P A R E N T H E S E S .
Figure 6. Adapter Bar for M12 Arms Rack.
0030-7
1 V S 2 9 6
TM 9-1005-319-23&P
0030
ILLUSTRATIONS OF MANUFACTURED ITEMS - Continued
0 .0 6 2 5 + 0 .0 1 5 D I A
7 5 ° + 5 °
0 .2 5 0 + 0 .0 6 2 5
F A B R I C A T E F R O M N E E D L E N O S E P L I E R S ,
N S N 5 1 2 0 -0 0 -2 6 8 -3 5 7 9 O R E Q U I V A L E N T .
N O T E : A L L D I M E N S I O N S S H O W N
A R E I N
I N C H E S .
Figure 7. Modified Needle Nose Pliers.
END OF WORK PACKAGE
0030-8
1 V S 2 9 7
TM 9-1005-319-23&P
CHAPTER 4
AUXILIARY EQUIPMENT
MAINTENANCE INSTRUCTIONS
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
0031
FIELD MAINTENANCE
AUXILIARY EQUIPMENT
INITIAL SETUP:
References
WP 0042
AUXILIARY EQUIPMENT
The following items of auxiliary equipment are used in conjunction with the weapons:
1.
40mm Grenade Launcher M203, NSN 1010-00-179-6447 (Rifle Only).
2.
40mm Grenade Launcher M203A1, NSN 1010-01-434-9028 (Carbine Only).
3.
40mm Grenade Launcher M203A2, NSN 1010-01-495-8511 (M16A3/M16A4 Rifle or Carbine Only).
4.
Conversion Kit, M261 (caliber .22 rimfire adapter), NSN 1005-01-010-1561.
5.
Bayonet-Knife M7, NSN 1005-00-073-9238.
6.
Bayonet-Knife Scabbard M10, NSN 1095-00-223-7164.
7.
M9 Multi-Purpose Bayonet System, NSN 1005-01-227-1739.
8.
Night Vision Sight, Individual Served Weapon, AN/PVS-4, NSN 5855-00-629-5334.
9.
M2 Practice Bolt, NSN 1005-01-184-4041.
10.
M68 Reflex Sight, NSN 1240-01-540-3690.
11.
M30 Boresight, NSN 4933-01-394-7781.
12.
Flashlight Mount, NSN 5340-01-485-1916 (M16A3/M16A4 Rifle or Carbine Only).
13.
Target Pointer Illuminator/Aiming Light (TPIAL), AN/PEQ-2A, NSN 5855-01-447-8992 (M16/M4
Series).
14.
Light Weapon Thermal Sight (LWTS), AN/PAS-13B(V)1, NSN 5855-01-464-3150 (M16/M4 Series).
15.
Medium Weapon Thermal Sight (MWTS), AN/PAS-13A(V)2, NSN 5855-01-458-0210 (M16/M4 Series).
16.
Heavy Weapon Thermal Sight (HWTS), AN/PAS-13A(V)3, NSN 5855-01-458-0211 (M16/M4 Series).
17.
Monocular Night Vision Device, AN/PVS-14, NSN 5855-01-432-0524 (M16/M4 Series).
18.
Enhanced Sliding Buttstock Assembly, NSN 1005-01-544-9825.
0031-1
TM 9-1005-319-23&P
AUXILIARY EQUIPMENT - Continued
19.
Tactical Sling, NSN 1005-01-541-1771.
20.
Cleaning Kit, NSN 1005-01-558-7980.
21.
Forward Rail Bracket, NSN 1005-01-541-2476.
22.
Multi-mag Holder, NSN 1005-01-541-2477.
23.
Forward Grip Bipod, NSN 1005-01-541-1772.
24.
Lock Plate, NSN 1005-00-233-9031.
25.
Top Sling Adapter, NSN 1005-00-406-1570.
26.
Close Quarters Battle Sling Kit, NSN 1005-01-478-0848.
27.
Blank Firing Attachment M15A2, NSN 1005-00-118-6192 (Rifle Only).
28.
Blank Firing Attachment M23, NSN 1005-01-361-8208 (Carbine Only).
29.
Carrying Handle Assembly, NSN 1005-01-465-0401.
30.
M12 Storage Rack, NSN 1095-00-407-0674.
See WP 0042 for applicable publications.
0031-2
0031
TM 9-1005-319-23&P
FIELD MAINTENANCE
LOCK PLATE MAINTENANCE
INSTALLATION, REPAIR OR REPLACEMENT, REMOVAL
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
0032-1
0032
TM 9-1005-319-23&P
0032
WARNING
The lock plate prevents the selector lever from being placed in BURST and
will be installed at the discretion of the unit commander. It is mandatory
for use in civil disturbance (riot control).
INSTALLATION
2
1
3
3
4
1 v s 3 0 1
Figure 1. Removing Pistol Grip for Lock Plate Installation.
1.
Using a screwdriver, reach inside pistol grip (3) and remove screw (2) and lockwasher (1).
WARNING
To avoid injury to your eyes, use care when removing or installing springloaded parts.
2.
Carefully remove pistol grip (3). Hold detent helical spring (4) in place.
0032-2
TM 9-1005-319-23&P
0032
4
5
4
5
1 v s 3 0 2
Figure 2. Installing Lock Plate.
3.
Install lock plate (5) with the detent helical spring (4) passing through the hole in the right side of the
lock plate and the arm on the outside of the receiver. The selector lever must point to the SAFE
position.
4
3
1 v s 3 0 3
Figure 3. Positioning Pistol Grip with Lock Plate Installed.
4.
Carefully compress detent helical spring (4) and position pistol grip (3).
0032-3
TM 9-1005-319-23&P
0032
INSTALLATION - Continued
2
1
3
1 v s 3 0 4
Figure 4. Securing Pistol Grip with Lock Plate Installed.
5.
Using screwdriver, secure pistol grip (3) by installing lockwasher (1) and screw (2).
END OF TASK
REPAIR OR REPLACEMENT
Inspect lock plate for serviceability and broken arm. Replace if unserviceable or if arm is broken.
END OF TASK
REMOVAL
2
1
3
3
4
1 v s 3 0 1
Figure 5. Removing Pistol Grip for Lock Plate Removal.
0032-4
TM 9-1005-319-23&P
1.
0032
Using a screwdriver, reach inside pistol grip (3) and remove screw (2) and lockwasher (1).
WARNING
To avoid injury to your eyes, use care when removing or installing springloaded parts.
2.
Carefully remove pistol grip (3). Hold detent helical spring (4) in place.
4
5
4
5
1 v s 3 0 2
Figure 6. Removing Lock Plate.
3.
Remove lock plate (5) while continuing to hold the detent helical spring (4) in place. The selector lever
must point to the SAFE position.
0032-5
TM 9-1005-319-23&P
0032
REMOVAL - Continued
4
3
1 v s 3 3 0
Figure 7. Positioning Pistol Grip with Lock Plate Removed.
4.
Carefully compress detent helical spring (4) and position pistol grip (3).
2
1
3
1 v s 3 0 4
Figure 8. Securing Pistol Grip with Lock Plate Removed.
5.
Using screwdriver, secure pistol grip (3) by installing lockwasher (1) and screw (2).
END OF TASK
END OF WORK PACKAGE
0032-6
TM 9-1005-319-23&P
0033
FIELD MAINTENANCE
TOP SLING ADAPTER MAINTENANCE
INSTALLATION, REPAIR OR REPLACEMENT, REMOVAL
INITIAL SETUP:
Materials/Parts
Top sling adapter kit, PN 8448471
References
TM 9-1005-319-10
Equipment Conditions
Sling removed (TM 9-1005-319-10)
INSTALLATION
1
2
R I F L E
1
3
C A R B I N E
1 v s 3 0 5
Figure 1. Installing Top Sling Adapter.
1.
Rifle Only: Install top sling adapter strap (1) through sling swivel (2) and tie.
2.
Carbine Only: Install top sling adapter strap (1) through sling opening (3) and tie.
0033-1
TM 9-1005-319-23&P
0033
INSTALLATION - Continued
4
5
6
1 v s 3 0 6
Figure 2. Installing Clamp on Front Sight.
3.
Remove upper handguard assembly (4). Refer to TM 9-1005-319-10.
4.
Use pliers to install clamp (5) on front sight base (6).
7
7
1
5
4
1 v s 3 0 7
Figure 3. Attaching Sling to Top Sling Adapter and Clamp.
5.
Attach sling (7) to top sling adapter strap (1) and to clamp (5).
0033-2
TM 9-1005-319-23&P
0033
6.
Install upper handguard assembly (4). Refer to TM 9-1005-319-10.
7.
Adjust sling (7).
END OF TASK
REPAIR OR REPLACEMENT
Visually inspect top sling adapter strap and replace if it is badly worn or damaged.
END OF TASK
REMOVAL
7
7
4
1
5
1 v s 3 0 8
Figure 4. Removing Sling from Clamp and Top Sling Adapter.
1.
Remove upper handguard assembly (4). Refer to TM 9-1005-319-10.
2.
Remove sling (7) from clamp (5) and top sling adapter strap (1).
0033-3
TM 9-1005-319-23&P
0033
REMOVAL - Continued
5
6
1 v s 3 0 9
Figure 5. Removing Clamp from Front Sight.
3.
Use pliers to remove clamp (5) from front sight base (6).
4
1 v s 3 1 0
Figure 6. Attaching Sling to Top Sling Adapter and Clamp.
4.
Install upper handguard assembly (4). Refer to TM 9-1005-319-10.
0033-4
TM 9-1005-319-23&P
0033
1
1
3
2
R I F L E
C A R B I N E
1 v s 3 1 1
Figure 7. Removing Top Sling Adapter.
5.
Untie top sling adapter (1) and remove from sling swivel (2) or sling opening (3). Use pliers to remove
clamp (5) from front sight base (6).
6.
Install sling. Refer to TM 9-1005-319-10.
END OF TASK
END OF WORK PACKAGE
0033-5/6 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
CLOSE QUARTERS BATTLE SLING MAINTENANCE
INSTALLATION, REPAIR OR REPLACEMENT
INITIAL SETUP:
Tools and Special Tools
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Close quarters combat sling adapter kit, PN 12956271
0034-1
0034
TM 9-1005-319-23&P
0034
INSTALLATION
1
2
R I F L E
O N L Y
1 v s 3 1 2
Figure 1. Removing Sling Swivel.
1.
Knock out tubular rivet (2) with a hammer and punch and remove small sling swivel (1). Discard
tubular rivet.
3
C A R B I N E
O N L Y
1 v s 3 1 3
Figure 2. Removing Two Spring Pins.
2.
Using hammer and punch, remove two spring pins (3). Discard spring pins.
0034-2
TM 9-1005-319-23&P
0034
4
5
C A R B I N E
O N L Y
1 v s 3 1 4
Figure 3. Removing Swivel Locking Bar.
3.
Lift swivel locking bar (4) up and out of swivel mount (5).
5
C A R B I N E
O N L Y
1 v s 3 1 5
Figure 4. Removing Swivel Mount.
4.
Remove swivel mount (5).
6
1 v s 3 1 6
Figure 5. Installing Barrel Band.
5.
Install barrel band (6) under front sight post. The barrel band must be bent out to fit around the
barrel, then bent back close after installation to ensure proper fit around the barrel.
0034-3
TM 9-1005-319-23&P
0034
INSTALLATION - Continued
B A R R E L B A N D
B A R R E L
N U T
L A N Y A R D
A S S Y
S O C K E T H E A D
C A P S C R E W
1 v s 3 1 7
Figure 6. Attaching Lanyard Assembly.
6.
Attach lanyard assembly to the barrel band using supplied hardware, 7/64 in. hex key wrench, and
pliers.
7
8
1 v s 3 1 8
Figure 7. Attaching Rear Sling Adapter.
7.
Put the rear loop (7) around the buttstock and pass the loop lock through the swivel exactly as shown in
Figure 7.
8.
Attach rear sling adapter (8) to buttstock as shown in Figure 7.
8
9
1 v s 3 1 9
Figure 8. Assembling Sling to Rear Sling Adapter.
9.
Assemble standard sling (9) to rear sling adapter (8) as shown in Figure 8.
0034-4
TM 9-1005-319-23&P
9
0034
1 0
1 v s 3 2 0
Figure 9. Attaching Sling to Quick Release Swivel.
10.
Attach end of standard sling (9) to quick release swivel (10) as shown in Figure 9.
1 0
1 0
1 v s 3 2 1
Figure 10. Attaching Swivel to Lanyard.
11.
Attach swivel (10) to lanyard assembly. Unscrew nut counterclockwise while pulling outward, stopping
when resistance is felt. Push inward on plastic nut and rotate plate a quarter turn.
1 0
9
1 v s 3 2 2
Figure 11. Securing Swivel and Lanyard.
12.
The swivel (10) can be attached to the lanyard in one of two ways; it can be attached either to the lug
on the end of the lanyard or to the lug attached to the barrel band. When the lanyard is attached to the
barrel lug, note that the lanyard is dressed around the sling (9) and inserted between the layers of the
sling.
END OF TASK
REPAIR OR REPLACEMENT
Visually inspect close quarters battle sling and replace if it is badly worn or damaged.
END OF TASK
END OF WORK PACKAGE
0034-5/6 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
BLANK FIRING ATTACHMENT MAINTENANCE
INSTALLATION, REPAIR OR REPLACEMENT, REMOVAL
INITIAL SETUP:
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Paint, enamel (Red Rifles) (WP 0045, item 24)
Paint, enamel (Yellow Carbines) (WP 0045, item 25)
WARNING
Do not keep live ammunition near work area.
Only blank cartridge M200 is to be used when the blank firing attachment is
attached to the rifle/carbine.
Do not fire blank ammunition at a target at distances of less than 20 feet
(6.1 m). The unburned propellant grains can cause injury within this
distance.
INSTALLATION
1
2
1 v s 3 2 3
Figure 1. Unscrewing Slide.
NOTE
M23 blank firing attachment is stamped "M4 Carbine Only" painted yellow and may
be used on the M4 and M4A1 carbines. M15A2 blank firing attachment is painted
red and is used on the M16A2, M16A3, and M16A4 rifle.
1.
Unscrew and pull slide (1) all the way out on the blank firing attachment (2).
0035-1
0035
TM 9-1005-319-23&P
0035
INSTALLATION - Continued
2
3
1 v s 3 2 4
Figure 2. Placing Blank Firing Attachment.
2.
Hook blank firing attachment (2) behind the first groove of the compensator (3).
1
3
1 v s 3 2 5
Figure 3. Securing Blank Firing Attachment.
CAUTION
Do not use tools to tighten the blank firing attachment. Use hands only.
3.
Push slide (1) into compensator (3) and hand tighten.
NOTE
Check for tightness after firing approximately 50 blank rounds.
END OF TASK
REPAIR OR REPLACEMENT
1.
Clean blank firing attachment with CLP (WP 0045, item 9), wipe dry, and coat with CLP.
2.
Inspect blank firing attachment for cracks or distortion. Be sure the parts in the slide are clear and
clean. If blank firing attachment is cracked or distorted, it is unserviceable.
0035-2
TM 9-1005-319-23&P
0035
3.
Repaint blank firing attachment using enamel paint. Use red (WP 0045, item 24) for M16A2, M16A3,
and M16A4 rifles or yellow (WP 0045, item 25) for M4 and M4A1 carbines. Painting is the only repair
authorized.
4.
Replace blank firing attachment if unserviceable.
END OF TASK
REMOVAL
CAUTION
Do not use tools to tighten the blank firing attachment. Use hands only.
1
3
1 v s 3 2 6
Figure 4. Unscrewing Slide from Compensator.
1.
Unscrew slide (1) to remove from compensator (3).
3
2
1 v s 3 2 7
Figure 5. Removing Blank Firing Attachment.
2.
Unhook blank firing attachment (2) from behind the first groove of the compensator (3).
0035-3
TM 9-1005-319-23&P
REMOVAL - Continued
1
2
1 v s 3 2 8
Figure 6. Securing Slide in Blank Firing Attachment.
3.
Screw slide (1) all the way in on blank firing attachment (2).
END OF TASK
END OF WORK PACKAGE
0035-4
0035
TM 9-1005-319-23&P
0036
FIELD MAINTENANCE
M12 STORAGE RACK MAINTENANCE
INSTALLATION
INITIAL SETUP:
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Adapter bar (WP 0030, Figure 6)
Machine screw (2) (MS35206-315)
Mounting bracket (WP 0045, item 23)
Nut (2) (MS35649-2382)
Olive drab enamel (WP 0045, item 16)
Rail protector (WP 0045, item 29)
Washer (4) (MS27183-15)
INSTALLATION
M4/M4A1 Carbine Only:
1.
When storing the M4/M4A1 carbine in the M12 storage rack, an adapter bar (WP 0030, Figure 6)
MUST be used for security reasons. This minor alteration to the M12 storage rack must be performed
by field maintenance. Install the adapter bar to the M12 storage rack as follows:
a.
Remove all weapons from the M12 storage rack and position the M12 storage rack to gain access to
the back.
0036-1
TM 9-1005-319-23&P
0036
INSTALLATION - Continued
M
A R K C E N T E R
L I N E
O F L E G A N D A D A P T E R
B A R
1
2
1 v s 3 2 9
Figure 1. Installing Adapter Bar on M12 Storage Rack.
0036-2
TM 9-1005-319-23&P
0036
b.
The side of the adapter bar with the cut off corners (1) is the top and the side with the square
corners (2) is the back. The portion of the bar must be placed so the cut corners face the front of the
M12 storage rack.
c.
Holding the adapter bar at an angle, place one end into position inside the rear leg of the M12
storage rack. Lower the other end of the bar into position. Allow the adapter bar to rest on the
M12 storage rack.
d.
Clamp both ends of the adapter bar into position. Mark the center line of the leg and adapter bar
where they meet (see Figure 1). Using a center punch, mark the location of the holes to be drilled
where the center lines cross. The holes must be centered on both the leg and the adapter bar. Drill
a 1/8 in. pilot hole through both M12 storage rack legs and the ends of the adapter bar. Drill a 3/8
in. hole through both M12 storage rack legs and the ends of the adapter bar using the pilot hole as
a guide. Remove the adapter bar. File the edges of all holes smooth. Paint all bare metal surfaces
with olive drab enamel paint (WP 0045, item 16).
e.
Reinsert the adapter bar into position on the M12 storage rack. Using two 3/8 in. x 2 in. machine
screws (MS35206-315, NSN 5305-00-984-5695 or equivalent), four washers (MS27183-15, NSN
5310-00-809-4061 or equivalent), and two nuts (MS35649-2382, NSN 5310-00-056-3395 or
equivalent), assemble adapter bar to M12 storage rack and tighten securely. The bolts can be
inserted from either the back or the front to meet your requirements. If the M12 storage rack is
placed close to a wall or another M12 storage rack, it is recommended that the bolts be inserted
from the back.
f.
Tack weld, braze, or peen the threaded portion of the bolt to the nut to prevent easy removal.
g.
Place M12 storage rack back into position and replace the weapons.
NOTE
It is necessary to either remove the carrying handle or move it back one notch in
order to secure the locking bars of the M12 storage rack during storage of the M16A4
rifle and M4/M4A1 carbine. DO NOT mix back-up carrying handles from one weapon
to another; it may change the zero of the last weapon.
2.
It is recommended that the rail protector (WP 0045, item 29) be used during storage of the carbines
when the carrying handle assembly or some accessory is not installed on the upper receiver to prevent
damage to the mounting surface on the upper receiver.
0036-3
TM 9-1005-319-23&P
0036
INSTALLATION - Continued
M16A4 Rifle and M4/M4A1 Carbine:
NOTE
Organizations that are having difficulty securing the M16A4 rifle with M5 adapter
rail system mounted or M4/M4A1 carbine with M4 adapter rail system mounted are
authorized the following minor alteration to the M12 storage rack.
Due to differing physical dimensions of the M12 storage racks (construction
tolerances), a locking bar is required when storing M16A4 rifles or M4/M4A1
carbines with adapter rail systems installed.
1.
Fabricate and install locking bars as follows:
NOTE
The best length of the locking bar for each storage rack varies. The bar should be cut
to the length that gives a very tight fit to ensure the M12 storage rack will meet arms
rack certification criteria when using this locking bar. Measure and cut each length
of angle iron to best fit each storage rack.
a.
Cut each piece of stock 1-1/4 in. x 1/8 in. angle iron needed for locking bars (one for each M12
storage rack). The dimensions shown below are approximate. Place the cross locking bars of the
M12 storage rack in the up (unlocked) position.
b.
Place each piece of cut angle iron on each M12 storage rack separately to identify the location for
the lock hole. Place the angle iron on the M12 storage rack with the angle iron behind the M12
storage rack lock hole. From the front of the M12 storage rack, trace the M12 lock hole onto the
locking bar. The traced hole on the locking bar is larger than 3/8 in. (0.92 cm).
c.
Drill a 3/8 in. (0.92 cm) hole in the locking bar close to the top of the oversized traced hole on the
angle iron. Ensure that as much metal as possible is left in the bottom portion of the angle iron's
lock hole when drilling (1/8 in. (0.32 cm) minimum). Grind all cut and drilled surfaces to remove
burrs.
d.
Position the two cross locking bars of the M12 storage rack in the up position.
e.
Place the M16A4, M4, or M4A1 weapons with the mounted adapter rail systems in the M12 storage
rack.
f.
Place the fabricated M12 locking bar on the M12 storage rack with the lock hole of the locking bar
behind the lock hole of the M12 storage rack. Place a series 200 lock through the lock holes and
lock.
0036-4
TM 9-1005-319-23&P
0036
A p p r o x im a te ly
3 5 3 /4 in .
C u t le n g th fo r b e s t fit fo r e a c h r a c k .
1 in .
A p p r o x im a te ly
L o c k H o le
3 /8 in .
W h e n d r illin g t h e 3 /8 in . lo c k h o le ,
le a v e a s m u c h m e ta l in ta c t a t th is
lo c a t io n a s p o s s ib le (1 /8 in . m in im u m ).
Figure 2. Fabrication of Locking Bar.
END OF TASK
END OF WORK PACKAGE
0036-5/6 blank
1 in .
A p p r o x im a te ly
1 v s 3 3 1
TM 9-1005-319-23&P
FIELD MAINTENANCE
CARRYING HANDLE ASSEMBLY MAINTENANCE
DISASSEMBLY, REPAIR OR REPLACEMENT, LUBRICATION,
ASSEMBLY, TEST AND INSPECTION
EFFECTIVITY NOTICE
M16A3, M16A4 RIFLE
M4, M4A1 CARBINE
INITIAL SETUP:
Tools and Special Tools
Small Arms Shop Set: Field Maintenance, Basic, Less Power, SC 4933-95-A11
Small Arms Tool Kit, SC 5180-95-B71
Materials/Parts
Cleaner, lubricant, and preservative (CLP) (WP 0045, item 9)
Index screw 9349065
Solid film lubricant (WP 0045, item 20)
References
WP 0039
0037-1
0037
TM 9-1005-319-23&P
0037
DISASSEMBLY
2
3
1
4
R
1 1
5
1 0
6
9
7
8
1 v s 2 2 1
Figure 1. Disassembly of Carrying Handle Assembly.
WARNING
To avoid injury to eyes, use care when removing spring-loaded parts.
1.
Drive out spring pin (8) using a 3/32 in. punch. Catch helical spring (7) when punch is withdrawn.
2.
Rotate elevating mechanism (1) until rear sight assembly (3) clears gun carrying handle (6). Catch ball
bearing (5) and helical spring (4).
3.
Push elevating mechanism (1) out with thumb using slight rotation motion. Catch ball bearing (10)
and helical spring (9).
4.
Use 1/16 in. key wrench to remove index screw (2). Discard index screw. Separate elevating
mechanism (1) from knob (11) by hand.
END OF TASK
REPAIR OR REPLACEMENT
1.
Check rear sight parts for serviceability. Inside of apertures should be round and distinct. Replace if
defective.
2.
Visually inspect rear sight assembly helical springs and ball bearings for breaks, bends, and missing
parts. Ball bearings should be smooth and round. Replace if defective.
3.
Check elevating mechanism for legibility of markings.
0037-2
TM 9-1005-319-23&P
0037
4.
Check rear sight assembly for serviceability. Clear drain holes for springs. Threaded portion of rear
sight assembly and knob should be well formed.
5.
Inspect rear sight guards for bends; if bent, repair as follows:
1 2
1 2
1 3
1 v s 2 2 2
Figure 2. Straightening Rear Sight Guards.
a.
Place carrying handle assembly (13) in a vise using jaw clamps. Tighten vise.
b.
Using two adjustable wrenches, gradually bend guards (12) to straighten. When bending the
guards, gradually bend beyond the straight point as the guard will partially return when bending
pressure is stopped.
c.
After straightening, use a flat file to remove any nicks, kinks, or burrs that remain on the inside of
guards (12).
WARNING
SOLID FILM LUBRICANT
CAUTION
Do not use wire brush on aluminum surfaces.
6.
d.
Apply solid film lubricant (WP 0045, item 20) to brightened area for final protective coating.
e.
If rear sight guards cannot be straightened utilizing the above procedures, replace the carrying
handle assembly.
Inspect all parts for damage and wear. Replace all defective parts as authorized by WP 0039.
END OF TASK
0037-3
TM 9-1005-319-23&P
0037
LUBRICATION
Lubricate rear sight assembly. Apply cleaner, lubricant, and preservative (CLP) (WP 0045, item 9) to helical
springs and ball bearings and threaded portion of index screw before installation. Lubricate helical springs
and ball bearings through their respective drain holes.
END OF TASK
ASSEMBLY
2
1
1 1
1 0
1 4
9
6
1 v s 2 2 3
Figure 3. Assembly and Installation of Elevation Knob Assembly.
1.
Assemble knob (11), elevating mechanism (1), and new index screw (2) using 1/16 in. key wrench. Do
not overtighten index screw as scale will require adjustment.
2.
Install ball bearing (10) and helical spring (9) using needle-nose pliers or tweezers.
3.
Depress ball bearing (10) with a punch inserted through access hole, and slide elevation knob assembly
(14) into gun carrying handle (6) from the side. Center elevation knob assembly.
0037-4
TM 9-1005-319-23&P
0037
WARNING
To avoid injury to eyes, use care when installing spring-loaded parts.
3
4
R
5
6
1 4
1 v s 2 2 4
Figure 4. Installation of Rear Sight Assembly.
4.
Install helical spring (4) and ball bearing (5).
5.
Insert threaded portion of rear sight assembly (3) into gun carrying handle (6) and rotate elevation
knob assembly (14) until threads engage.
6.
Rotate elevation knob assembly (14) until rear sight assembly (3) is all the way down. Then come up 22
clicks before installing spring pin.
0037-5
TM 9-1005-319-23&P
0037
ASSEMBLY - Continued
1 5
8
6
1 4
7
3
1 v s 2 2 5
Figure 5. Installation of Helical Spring.
CAUTION
Ensure that spring pin passes over helical spring, not through its coils.
7.
Insert helical spring (7) through underside of gun carrying handle (6). Compress helical spring with a
small tip screwdriver (15) to install spring pin (8). Spring pin must pass over helical spring, not
through its coils. Rotate elevation knob assembly (14) until rear sight assembly (3) is all the way down.
END OF TASK
TEST AND INSPECTION
1.
Rotate and test elevating mechanism for ease of functioning.
2.
Inspect elevation knob zero as follows:
a.
Rotate knob counterclockwise until the rear sight assembly is all the way down. If a whole click is
not felt as the rear sight assembly stops, the rear sight assembly has bottomed out and will not
pivot freely.
b.
Position knob back slightly to its last whole click so the rear sight assembly is under tension of ball
bearing and helical spring. The 300 meter mark should align with mark on carrying handle
assembly on the left side.
0037-6
TM 9-1005-319-23&P
c.
0037
If 300 meter mark is not aligned with mark on carrying handle assembly, slip range scale in the
following manner:
(1)
Position 300 meter mark with mark on carrying handle assembly.
(2)
Insert a 1/16 in. key wrench through access hole of rear sight assembly and into index screw.
(3)
Loosen index screw three turns and leave wrench in place.
(4)
Rotate lower portion of knob counterclockwise until it stops (range scale should not have
moved). Knob should be positioned on its last whole click.
(5)
Tighten index screw and remove wrench.
(6)
Check for proper setting.
END OF TASK
END OF WORK PACKAGE
0037-7/8 blank
TM 9-1005-319-23&P
CHAPTER 5
PARTS INFORMATION
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
0038
FIELD MAINTENANCE
INTRODUCTION TO REPAIR PARTS AND SPECIAL TOOLS LIST (RPSTL)
INTRODUCTION
SCOPE
This RPSTL lists and authorizes spares and repair parts; special tools; special test, measurement, and
diagnostic equipment (TMDE); and other special support equipment required for performance of field
maintenance of the M16 series rifles and the M4 series carbines. It authorizes the requisitioning, issue, and
disposition of spares, repair parts, and special tools as indicated by the source, maintenance, and
recoverability (SMR) codes.
GENERAL
In addition to the Introduction work package, this RPSTL is divided into the following work packages.
1. Repair Parts List Work Packages. Work packages containing lists of spares and repair parts authorized
by this RPSTL for use in the performance of maintenance. These work packages also include parts which
must be removed for replacement of the authorized parts. Parts lists are composed of functional groups in
ascending alphanumeric sequence, with the parts in each group listed in ascending figure and item number
sequence. Sending units, brackets, filters, and bolts are listed with the component they mount on. Bulk
materials are listed by item name in FIG. BULK at the end of the work packages. Repair parts kits are
listed separately in their own functional group and work package. Repair parts for reparable special tools
are also listed in a separate work package. Items listed are shown on the associated illustrations.
2. Special Tools List Work Packages. Work packages containing lists of special tools, special TMDE, and
special support equipment authorized by this RPSTL (as indicated by Basis of Issue (BOI) information in the
DESCRIPTION AND USABLE ON CODE (UOC) column). Tools that are components of common tool sets
and/or Class VII are not listed.
3. Cross-Reference Indexes Work Packages. There are two cross-reference indexes work packages in this
RPSTL: the National Stock Number (NSN) Index work package and the Part Number (P/N) Index work
package. The National Stock Number Index work package refers you to the figure and item number. The
Part Number Index work package refers you to the figure and item number.
EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST WORK
PACKAGES
ITEM NO. (Column (1)). Indicates the number used to identify items called out in the illustration.
SMR CODE (Column (2)). The SMR code containing supply/requisitioning information, maintenance level
authorization criteria, and disposition instruction, as shown in the following breakout:
0038-1
TM 9-1005-319-23&P
0038
EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST WORK
PACKAGES - Continued
Table 1. SMR Code Explanation.
Source
Code
Maintenance
Code
___
xx
___
1st two
positions:
How to get an
item.
Recoverability
Code
___
xx
___
3rd position:
Who can install, replace,
or use the
item.
___
x
___
4th position:
Who can do
complete
repair* on the
item.
5th position:
Who determines
disposition action
on unserviceable
items.
*Complete Repair: Maintenance capacity, capability, and authority to perform all corrective maintenance
tasks of the "Repair" function in a use/user environment in order to restore serviceability to a failed item.
Source Code. The source code tells you how to get an item needed for maintenance, repair, or overhaul of an
end item/equipment. Explanations of source codes follow:
Source Code
PA
PB
PC
PD
PE
PF
PG
PH
PR
PZ
Application/Explanation
NOTE
Items coded PC are subject to deterioration.
Stock items; use the applicable NSN to requisition/request items
with these source codes. They are authorized to the level indicated
by the code entered in the third position of the SMR code.
KD
KF
KB
Items with these codes are not to be requested/requisitioned
individually. They are part of a kit which is authorized to the
maintenance level indicated in the third position of the SMR code.
The complete kit must be requisitioned and applied.
MO- Made at unit/
AMC level
MF- Made at DS/
ASB level
MH- Made at sustainment
level
ML- Made at SRA/TASMG
MD- Made at depot
MG- Navy only
Items with these codes are not to be requisitioned/requested
individually. They must be made from bulk material which is
identified by the part number in the DESCRIPTION AND
USABLE ON CODE (UOC) column and listed in the bulk material
group work package of the RPSTL. If the item is authorized to you
by the third position code of the SMR code, but the source code
indicates it is made at higher level, order the item from the higher
level of maintenance.
0038-2
TM 9-1005-319-23&P
Application/Explanation
Source Code
AOAFAHALADAG-
0038
Assembled by
unit/AMC level
Assembled by
DS/ASB level
Assembled by
sustainment level
Assembled by
SRA/TASMG
Assembled by
depot
Navy only
XA
Items with these codes are not to be requested/requisitioned
individually. The parts that make up the assembled item must be
requisitioned or fabricated and assembled at the level of maintenance
indicated by the source code. If the third position of the SMR code
authorizes you to replace the item, but the source code indicates the
item is assembled at a higher level, order the item from the higher
level of maintenance.
Do not requisition an "XA" coded item. Order the next higher
assembly. (Refer to NOTE below.)
If an item is not available from salvage, order it using the CAGEC
and part number.
Installation drawings, diagrams, instruction sheets, field service
drawings; identified by manufacturer's part number.
Item is not stocked. Order an XD-coded item through local purchase
or normal supply channels using the CAGEC and part number given,
if no NSN is available.
XB
XC
XD
NOTE
Cannibalization or controlled exchange, when authorized, may be used as a source of
supply for items with the above source codes, except for those source coded "XA" or
those aircraft support items restricted by requirements of AR 750-1.
Maintenance Code. Maintenance codes tell you the level(s) of maintenance authorized to use and repair
support items. The maintenance codes are entered in the third and fourth positions of the SMR code as
follows:
Third Position. The maintenance code entered in the third position tells you the lowest maintenance level
authorized to remove, replace, and use an item. The maintenance code entered in the third position will
indicate authorization to the following levels of maintenance:
Maintenance Code
Application/Explanation
O*
F
H
L
G
-
K
Z
-
D
-
Unit level/AMC maintenance can remove, replace, and use the item.
Direct support/ASB maintenance can remove, replace, and use the item.
Sustainment maintenance can remove, replace, and use the item.
Specialized repair activity/TASMG can remove, replace, and use the item.
Afloat and ashore intermediate maintenance can remove, replace, and use
the item (Navy only).
Contractor facility can remove, replace, and use the item.
Item is not authorized to be removed, replaced, or used at any maintenance
level.
Depot can remove, replace, and use the item.
*NOTE - Army may use C in the third position. However, for joint service publications, Army will use O.
0038-3
TM 9-1005-319-23&P
0038
EXPLANATION OF COLUMNS IN THE REPAIR PARTS LIST AND SPECIAL TOOLS LIST WORK
PACKAGES - Continued
Fourth Position. The maintenance code entered in the fourth position tells you whether or not the item is to
be repaired and identifies the lowest maintenance level with the capability to do complete repair (perform all
authorized repair functions).
NOTE
Some limited repair may be done on the item at a lower level of maintenance, if
authorized by the Maintenance Allocation Chart (MAC) and SMR codes.
Maintenance Code
Application/Explanation
O
F
-
H
L
-
D
G
-
K
Z
B
-
Unit/AMC is the lowest level that can do complete repair of the item.
Direct support/ASB is the lowest level that can do complete repair of the
item.
Sustainment is the lowest level that can do complete repair of the item.
Specialized repair activity/TASMG is the lowest level that can do complete
repair of the item.
Depot is the lowest level that can do complete repair of the item.
Both afloat and ashore intermediate levels are capable of complete repair of
item (Navy only).
Complete repair is done at contractor facility.
Nonreparable. No repair is authorized.
No repair is authorized. No parts or special tools are authorized for the
maintenance of "B" coded item. However, the item may be reconditioned by
adjusting, lubricating, etc., at the user level.
Recoverability Code. Recoverability codes are assigned to items to indicate the disposition action on
unserviceable items. The recoverability code is shown in the fifth position of the SMR code as follows:
Recoverability
Code
Z
-
O
-
F
-
H
-
D
-
L
-
A
-
Application/Explanation
Nonreparable item. When unserviceable, condemn and dispose of the item at
the level of maintenance shown in the third position of the SMR code.
Reparable item. When uneconomically reparable, condemn and dispose of
the item at the service/AMC level.
Reparable item. When uneconomically reparable, condemn and dispose of
the item at the field/ASB level.
Reparable item. When uneconomically reparable, condemn and dispose of
the item at the below depot sustainment level.
Reparable item. When beyond lower level repair capability, return to depot.
Condemnation and disposal of item are not authorized below depot level.
Reparable item. Condemnation and disposal not authorized below
Specialized Repair Activity (SRA) or theater aviation sustainment
maintenance group (TASMG).
Item requires special handling or condemnation procedures because of
specific reasons (such as precious metal content, high dollar value, critical
material, or hazardous material). Refer to appropriate manuals/directives for
specific instructions.
0038-4
TM 9-1005-319-23&P
Recoverability
Code
0038
Application/Explanation
G
-
K
-
Field level reparable item. Condemn and dispose at either afloat or ashore
intermediate levels (Navy only).
Reparable item. Condemnation and disposal to be performed at contractor
facility.
NSN (Column (3)). The NSN for the item is listed in this column.
CAGEC (Column (4)). The Commercial and Government Entity Code (CAGEC) is a five-digit code which is
used to identify the manufacturer, distributor, or Government agency/activity that supplies the item.
PART NUMBER (Column (5)). Indicates the primary number used by the manufacturer (individual,
company, firm, corporation, or Government activity), which controls the design and characteristics of the
item by means of its engineering drawings, specifications, standards, and inspection requirements to
identify an item or range of items.
NOTE
When you use an NSN to requisition an item, the item you receive may have a
different part number from the number listed.
DESCRIPTION AND USABLE ON CODE (UOC) (Column (6)). This column includes the following
information:
1. The federal item name and, when required, a minimum description to identify the item.
2. Part numbers of bulk materials are referenced in this column in the line entry to be manufactured or
fabricated.
3. Hardness Critical Item (HCI). A support item that provides the equipment with special protection from
electromagnetic pulse (EMP) damage during a nuclear attack.
4. The statement END OF FIGURE appears just below the last item description in column (6) for a given
figure in both the repair parts list and special tools list work packages.
QTY (Column (7)). The QTY (quantity per figure) column indicates the quantity of the item used in the
breakout shown on the illustration/figure, which is prepared for a functional group, subfunctional group, or
an assembly. A "V" appearing in this column instead of a quantity indicates that the quantity is variable
and quantity may change from application to application.
0038-5
TM 9-1005-319-23&P
0038
EXPLANATION OF CROSS-REFERENCE INDEXES WORK PACKAGES FORMAT AND COLUMNS
1. National Stock Number (NSN) Index Work Package. NSNs in this index are listed in National Item
Identification Number (NIIN) sequence.
STOCK NUMBER Column. This column lists the NSN in NIIN sequence. The NIIN consists of the last
nine digits of the NSN. When using this column to locate an item, ignore the first four digits of the NSN.
However, the complete NSN should be used when ordering items by stock number.
For example, if the NSN is 5385-01-574-1476, the NIIN is 01-574-1476.
FIG. Column. This column lists the number of the figure where the item is identified/located. The figures
are in numerical order in the repair parts list and special tools list work packages.
ITEM Column. The item number identifies the item associated with the figure listed in the adjacent FIG.
column. This item is also identified by the NSN listed on the same line.
2. Part Number (P/N) Index Work Package. Part numbers in this index are listed in ascending
alphanumeric sequence (vertical arrangement of letter and number combinations which places the first
letter or digit of each group in order A through Z, followed by the numbers 0 through 9 and each following
letter or digit in like order).
PART NUMBER Column. Indicates the part number assigned to the item.
FIG. Column. This column lists the number of the figure where the item is identified/located in the repair
parts list and special tools list work packages.
ITEM Column. The item number is the number assigned to the item as it appears in the figure referenced
in the adjacent figure number column.
SPECIAL INFORMATION
UOC. The UOC appears in the lower left corner of the Description Column heading. Usable on codes are
shown as "UOC:…" in the Description Column (justified left) on the first line under the applicable
item/nomenclature. Uncoded items are applicable to all models. Identification of the UOCs used in the
RPSTL are:
Code
AR8
AW4
AZ1
AS1
AY6
Used On
M16A2 Rifle
M16A3 Rifle
M16A4 Rifle
M4 Carbine
M4A1 Carbine
Fabrication Instructions. Bulk materials required to manufacture items are listed in the bulk material
functional group of this RPSTL. Part numbers for bulk materials are also referenced in the Description
Column of the line item entry for the item to be manufactured/fabricated. Detailed fabrication instructions
for items source coded to be manufactured or fabricated are found in WP 0030 of this manual.
Index Numbers. Items which have the word BULK in the figure column will have an index number shown
in the item number column. This index number is a cross-reference between the NSN / Part Number (P/N)
Index work packages and the bulk material list in the repair parts list work package.
0038-6
TM 9-1005-319-23&P
0038
HOW TO LOCATE REPAIR PARTS
1. When NSNs or Part Numbers Are Not Known.
First. Using the table of contents, determine the assembly group to which the item belongs. This is
necessary since figures are prepared for assembly groups and subassembly groups, and lists are divided into
the same groups.
Second. Find the figure covering the functional group or the subfunctional group to which the item belongs.
Third. Identify the item on the figure and note the number(s).
Fourth. Look in the repair parts list work packages for the figure and item numbers. The NSNs and part
numbers are on the same line as the associated item numbers.
2. When NSN Is Known.
First. If you have the NSN, look in the STOCK NUMBER column of the NSN index work package. The
NSN is arranged in NIIN sequence. Note the figure and item number next to the NSN.
Second. Turn to the figure and locate the item number. Verify that the item is the one you are looking for.
3. When Part Number Is Known.
First. If you have the part number and not the NSN, look in the PART NUMBER column of the part
number index work package. Identify the figure and item number.
Second. Look up the item on the figure in the applicable repair parts list work package.
END OF WORK PACKAGE
0038-7/8 blank
TM 9-1005-319-23&P
FIELD MAINTENANCE
RIFLE, 5.56MM (M16A2) 9349000; RIFLE, 5.56MM (M16A3) 12012000;
RIFLE, 5.56MM (M16A4) 12973001; CARBINE, 5.56MM (M4) 9390000;
AND CARBINE, 5.56MM (M4A1) 12972700
REPAIR PARTS LIST
0039-1
0039
TM 9-1005-319-23&P
0039
7
1
2
3 A
3
4
8
6
6 B
6 A
M 1 6 A 3 /M 1 6 A 4 R I F L E
5
1
2
M 1 6 A 2 R I F L E
7
3 B
3 C
8
6 C
4
6 D
5 A
M 4 /M 4 A 1 C A R B I N E
Figure 1. Rifle, 5.56mm (M16A2) 9349000; Rifle, 5.56mm (M16A3) 12012000;
Rifle, 5.56mm (M16A4) 12973001; Carbine, 5.56mm (M4) 9390000;
and Carbine, 5.56mm (M4A1) 12972700.
0039-2
1 v s fig 0 1
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 00
FIG. 1
1
2
3
3A
3B
3C
4
PAFFF 1005-00-017-9546 19204
AFFFF
AFFFF
AFFFF
AFFFF
AFFFF
19200
19200
19200
19200
19200
PACZZ 1005-00-921-5004 19200
8448517
13004788
9349050
12973010
12972680
12997148
8448670
0039-3
RIFLE, 5.56MM (M16A2)
9349000; RIFLE, 5.56MM
(M16A3) 12012000; RIFLE,
5.56MM (M16A4) 12973001;
CARBINE, 5.56MM (M4)
9390000; CARBINE, 5.56MM
(M4A1) 12972700
HANDLE ASSEMBLY, CHARGING
(FOR ASSY BREAKDOWN SEE
FIG. 6).....................................................
1
BOLT AND BOLT CARRIER
ASSEMBLY (FOR ASSY
BREAKDOWN SEE FIG. 3)..................
1
UPPER RECEIVER AND BARREL
ASSEMBLY (M16A2)
(FOR ASSY BREAKDOWN SEE
FIG. 7).....................................................
UOC:AR8
UPPER RECEIVER AND BARREL
ASSEMBLY (M16A3, M16A4)
(FOR ASSY BREAKDOWN SEE
FIG. 7).....................................................
UOC: AW4, AZ1
UPPER RECEIVER AND BARREL
ASSEMBLY (M4)
(FOR ASSY BREAKDOWN SEE
FIG. 7).....................................................
UOC:AS1
UPPER RECEIVER AND BARREL
ASSEMBLY (M4A1)
(FOR ASSY BREAKDOWN SEE
FIG. 7).....................................................
UOC:AY6
MAGAZINE CARTRIDGE
(30 ROUND)...........................................
1
1
1
1
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
5
5A
6
6A
6B
6C
6D
7
8
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
PACZZ 1005-01-216-4510 19204
(5)
PART
NUMBER
12624561
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
SLING, SMALL ARMS
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
PACZZ 1005-01-368-9852 19200
12011996
SLING, SMALL ARMS (M4, M4A1) ....
UOC:AS1, AY6
XAFFA
9349100
LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY (M16A2)
(FOR ASSY BREAKDOWN SEE
FIG. 15) ..................................................
UOC:AR8
XAFFA
XAFFA
XAFFA
XAFFA
19200
19200
19200
19200
19200
PAFFF 1005-01-484-8000 19200
PAFZZ
1005-01-453-6655 19200
12012001
12598101
9390011
12972690
12996812
12973101
LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY (M16A3)
(FOR ASSY BREAKDOWN SEE
FIG. 15) ..................................................
UOC:AW4
LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY (M16A4)
(FOR ASSY BREAKDOWN SEE
FIG. 15) ..................................................
UOC:AZ1
LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY (M4)
(FOR ASSY BREAKDOWN SEE
FIG. 15) ..................................................
UOC:AS1
LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY (M4A1)
(FOR ASSY BREAKDOWN SEE
FIG. 15) ..................................................
UOC:AY6
BACK-UP IRON SIGHT ASSEMBLY
(M16A3, M16A4, M4, M4A1)
(FOR ASSY BREAKDOWN SEE
FIG. 2).....................................................
UOC:AW4, AZ1, AS1, AY6
VERTICAL PISTOL GRIP
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
END OF FIGURE
0039-4
0039
(7)
QTY
1
1
1
1
1
1
1
1
1
TM 9-1005-319-23&P
0039
1
3
1 3
1 1
2
1 2
7
6
1 0
7
4
6
5
8
9
1 v s fig 0 2
Figure 2. Back-up Iron Sight Assembly (M16A3, M16A4, M4, M4A1) 12996812.
0039-5 blank/6
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 01
FIG. 2
BACK-UP IRON SIGHT
ASSEMBLY (M16A3, M16A4,
M4, M4A1) 12996812
1
PAFZZ
1005-01-497-2592 19200
12996813
FRAME, ASSEMBLY ............................
1
2
PAFZZ
5340-01-484-7999 19200
12996823
BAR, LOCKING.....................................
1
3
PAFZZ
5305-01-484-7075 19200
12996824
SCREW, RECOIL ..................................
1
4
PAFZZ
5315-00-058-6678 96906
MS16562-103 PIN, SPRING-TUBULAR,
SLOTTED...............................................
1
5
PAFZZ
5355-01-134-3627 19200
9349077
KNOB, WINDAGE ................................
1
6
PAFZZ
5360-01-148-1751 19200
9349069
SPRING, INDEX ...................................
2
7
PAFZZ
3110-00-183-9175 96906
MS19060-4808 BALL, BEARING, CORROSION
RESISTANT STEEL .............................
2
8
XAFZZ
19200
12996818
SIGHT, BASE ........................................
1
9
PAFZZ
5305-01-484-7074 19200
12996822
SCREW, WINDAGE ..............................
1
10
XAFZZ
19200
12996819
SIGHT, CAM..........................................
1
11
PAFZZ
5325-01-486-7585 96906
MS16624-3035 RING, RETAINING, EXTERNAL........
1
12
PAFZZ
5315-01-484-7071 19200
12996821
PLUNGER..............................................
1
13
PAFZZ
5360-01-484-7076 19200
12996820
SPRING, COMPRESSION....................
1
END OF FIGURE
0039-7
TM 9-1005-319-23&P
0039
1
2
3
4
5
1 v s fig 0 3
Figure 3. Bolt and Bolt Carrier Assembly 13004788.
0039-8
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 02
FIG. 3
BOLT AND BOLT CARRIER
ASSEMBLY 13004788
1
PAFZZ
1005-00-017-9547 19204
8448503
PIN, FIRING..........................................
1
2
PAFZZ
1005-00-999-1509 19204
8448504
PIN, FIRING PIN RETAINING ...........
1
3
PAFZZ
5315-00-992-7294 19204
8448502
PIN, GROOVED, HEADED
BOLT CAM.............................................
1
BOLT, BREECH ASSEMBLY
(FOR ASSY BREAKDOWN
SEE FIG. 4) ............................................
1
KEY AND BOLT CARRIER
ASSEMBLY (FOR ASSY
BREAKDOWN SEE FIG. 5)..................
1
4
5
PAFFF 1005-01-505-1035 19200
PAFFF 1005-01-441-1619 19204
13004787
8448505
END OF FIGURE
0039-9
TM 9-1005-319-23&P
0039
1
3
2
4
5
8
6
7
1 v s fig 0 4
Figure 4. Breech Assembly Bolt 13004787.
0039-10
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0201
FIG. 4
BREECH ASSEMBLY BOLT
13004787
1
PAFZZ
1005-00-992-7287 19204
8448511
RING, BOLT ..........................................
3
2
XAFZZ
19204
8448510
BOLT ......................................................
1
3
PAFZZ
1005-00-992-7290 19204
8448513
PIN, EXTRACTOR ................................
1
4
PAFZZ
5315-00-597-5086 80205
MS16562-98
PIN, SPRING EJECTOR ......................
1
5
PAFZZ
5360-00-992-7292 19204
8448516
SPRING, HELICAL,
COMPRESSION, EJECTOR ................
1
6
PAFZZ
1005-00-992-7291 19204
8448515
EJECTOR, CARTRIDGE ......................
1
7
PAFZZ
1005-00-992-7288 19204
8448512
EXTRACTOR, CARTRIDGE.................
1
8
PAFZZ
1005-01-505-2886 19200
13004786
SPRING ASSEMBLY, EXTRACTOR
(GOLD HUE SPRING) ..........................
1
END OF FIGURE
0039-11/12 blank
TM 9-1005-319-23&P
0039
1
2
3
1 v s fig 0 5
Figure 5. Key and Bolt Carrier Assembly 8448505.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0202
FIG. 5
KEY AND BOLT CARRIER
ASSEMBLY 8448505
1
PAFZZ
5305-00-992-7284 19204
8448508
SCREW, CARRIER KEY.......................
2
2
PAFZZ
1005-00-992-7283 19200
8448506
KEY, BOLT CARRIER ..........................
1
3
XAFZZ
19200
8448507
CARRIER, BOLT ...................................
1
END OF FIGURE
0039-13
TM 9-1005-319-23&P
0039
1
2
3
4
1 v s fig 0 6
Figure 6. Charging Handle Assembly 8448517.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 03
FIG. 6
1
PAFZZ
5315-01-048-9372 19204
8448521-2
CHARGING HANDLE
ASSEMBLY 8448517
PIN, SPRING, CHARGING
HANDLE ................................................
1
2
PAFZZ
5342-00-999-0405 19200
8448519
LATCH, CHARGING HANDLE ...........
1
3
PAFZZ
5360-00-999-0404 19204
8448520
SPRING, HELICAL, COMPRESSION,
CHARGING HANDLE ..........................
1
HANDLE, CHARGING .........................
1
4
XAFZZ
19204
8448518
END OF FIGURE
0039-14
TM 9-1005-319-23&P
0039
1
2
3
4
1 0
9
8
5
6
7
2
M 1 6 A 2 R I F L E
1 A
1 1
3
1 0
9
4 A
8
5
6
7
1 2
1 3
M 1 6 A 3 /M 1 6 A 4 R I F L E
1 v s fig 0 7 a
Figure 7. Upper Receiver and Barrel Assembly (M16A2) 9349050,
(M16A3, M16A4) 12973010, and (M4, M4A1) 12972680 (Sheet 1 of 2).
0039-15
TM 9-1005-319-23&P
0039
4 C
1 B
1 4
M 4 A 1 O N L Y
3 A
4 B
1 0
9
5
6
8
7
1 5
M 4 /M 4 A 1 C A R B I N E
1 v s fig 0 7 b
Figure 7. Upper Receiver and Barrel Assembly (M16A2) 9349050,
(M16A3, M16A4) 12973010, and (M4, M4A1) 12972680 (Sheet 2 of 2).
0039-16
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 04
FIG. 7
1
1A
1B
2
3
3A
4
4A
4B
4C
AFFFF
AFFFF
AFFFF
PAFZZ
PAFZZ
PAFZZ
19200
19200
19200
1005-01-134-3629 19200
4710-00-978-1038 19200
4710-01-233-8637 19200
PAFFF 1005-01-146-7684 19200
PAFFF 1005-01-454-1629 19200
PAFFF 1005-01-233-8529 19200
PAFFF 1005-01-471-5456 19200
9349062
12973011
12972675
9349059
8448567
9390016
9349124
12598107
9390007
12991851
0039-17
UPPER RECEIVER AND
BARREL ASSEMBLY
(M16A2) 9349050, (M16A3,
M16A4) 12973010, AND
(M4, M4A1) 12972680
UPPER RECEIVER ASSEMBLY
(M16A2) (FOR ASSY BREAKDOWN
SEE FIG. 12) ..........................................
UOC:AR8
UPPER RECEIVER ASSEMBLY
(M16A3, M16A4) (FOR ASSY
BREAKDOWN SEE FIG. 12)................
UOC:AW4, AZ1
UPPER RECEIVER ASSEMBLY
(M4, M4A1) (FOR ASSY
BREAKDOWN SEE FIG. 12)................
UOC:AS1, AY6
1
1
1
HANDGUARD ASSEMBLY
(M16A2) ..................................................
UOC:AR8
2
TUBE, BENT, METALLIC
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
1
TUBE, BENT, METALLIC
(M4, M4A1).............................................
UOC:AS1, AY6
1
BARREL ASSEMBLY (M16A2)
(FOR ASSY BREAKDOWN
SEE FIG. 8) ............................................
UOC:AR8
BARREL ASSEMBLY (M16A3,
M16A4) (FOR ASSY BREAKDOWN
SEE FIG. 8) ............................................
UOC:AW4, AZ1
BARREL AND FRONT SIGHT
ASSEMBLY, REPLACEMENT (M4)
(FOR ASSY BREAKDOWN
SEE FIG. 8) ............................................
UOC:AS1
BARREL AND FRONT SIGHT
ASSEMBLY, REPLACEMENT
(M4A1) (FOR ASSY BREAKDOWN
SEE FIG. 8) ............................................
UOC:AY6
1
1
1
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
5
PAFZZ
5310-01-475-9652 19200
12991533
WASHER, RECESSED .........................
1
6
PAFZZ
1005-01-134-3633 19200
9349051
COMPENSATOR...................................
1
7
PAFZZ
5315-00-058-6044 80205
MS16562-106 PIN, SPRING, GAS TUBE....................
1
8
PAFZZ
1005-00-087-8998 19204
8448712
RING, SLIP, HANDGUARD.................
1
9
PAFZZ
5360-00-978-1036 19204
8448555
SPRING, SLIP RING, HANDGUARD,
UPPER RECEIVER...............................
1
MS16626-3137 RING, RETAINING...............................
1
10
PAFZZ
11
PAFFF 1005-01-453-4225 19200
12
13
14
15
5325-00-999-0863 80205
PAFFF 1005-01-453-4224 19200
PAFZZ
1005-01-453-1635 19200
PAFFF 1005-01-453-4227 19200
PAFZZ
1005-01-453-1633 19200
12973021
12973139
12973029
12973096
12973099
UPPER HANDGUARD ASSEMBLY
(M16A3, M16A4) (FOR ASSY
BREAKDOWN SEE FIG. 9)..................
UOC:AW4, AZ1
BARREL STOP ASSEMBLY
(M16A3, M16A4) (FOR ASSY
BREAKDOWN SEE FIG. 10)................
UOC:AW4, AZ1
LOWER HANDGUARD
(M16A3, M16A4)....................................
UOC:AW4, AZ1
UPPER HANDGUARD ASSEMBLY
(M4, M4A1) (FOR ASSY
BREAKDOWN SEE FIG. 11)................
UOC:AS1, AY6
LOWER HANDGUARD (M4, M4A1) ...
UOC:AS1, AY6
END OF FIGURE
0039-18
1
1
1
1
1
TM 9-1005-319-23&P
0039
1
2
3
6
5
4
M 1 6 A 2 /M 1 6 A 3 /M 1 6 A 4 R I F L E
1
2
3
6 B
M 4 A 1
7
6 A
8
5
M 4 A N D
M 4 A 1 C A R B I N E
9
4
1 v s fig 0 8
Figure 8. Barrel Assembly (M16A2) 9349124, Barrel Assembly (M16A3, M16A4) 12598107,
Replacement Barrel and Front Sight Assembly (M4) 9390007,
and Replacement Barrel and Front Sight Assembly (M4A1) 12991851.
0039-19 blank/20
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0401
FIG. 8
BARREL ASSEMBLY (M16A2)
9349124, (M16A3, M16A4)
12598107, AND
REPLACEMENT BARREL
AND FRONT SIGHT
ASSEMBLY (M4) 9390007,
(M4A1) 12991851
1
PAFZZ
1005-01-134-3625 19200
9349056
POST, FRONT SIGHT ..........................
1
2
PAFZZ
5315-00-979-3930 19204
8448573
PIN, SHOULDER, HEADLESS
(DETENT, FRONT SIGHT) ..................
1
SPRING, HELICAL,
COMPRESSION, FRONT SIGHT........
1
3
PAFZZ
5360-00-979-3931 19204
8448574
4
PAFZZ
1005-00-017-9543 19204
8448571
SWIVEL, SLING, SMALL ....................
1
5
PAFZZ
5320-01-063-7635 19204
8448697
RIVET, TUBULAR ................................
1
6
XAFZZ
19200
9349054
BARREL AND BARREL
EXTENSION ASSEMBLY
(M16A2, M16A3, M16A4)......................
UOC: AR8, AW4, AZ1
6A
6B
7
XAFZZ
XAFZZ
PAFZZ
19200
19200
5340-01-474-2845 19200
9390009
12991850
12991254
1
BARREL AND BARREL
EXTENSION ASSEMBLY (M4) ...........
UOC: AS1
1
BARREL AND BARREL
EXTENSION ASSEMBLY (M4A1) ......
UOC: AY6
1
CLAMP, SYNCHRO (BAR,
LOCKING) (M4, M4A1) ........................
UOC:AS1, AY6
1
8
PAFZZ
5315-00-690-0544 80205
MS39086-93
PIN, SPRING (M4, M4A1) ....................
UOC:AS1, AY6
2
9
PAFZZ
1010-01-264-6517 19200
12598617
MOUNT, SWIVEL (M4, M4A1) ............
UOC:AS1, AY6
1
END OF FIGURE
0039-21/22 blank
TM 9-1005-319-23&P
2
1
3
F L A
C A N O
N E W S T
S
0039
N
T S P R
N L Y
Y L E S
P A C E
O T E
I N G
B E U
P E C
R (I T
(I T
S E
I A L
E M
D
E M
4 )
W I T H
S H A P E D
5 ).
4
6
5
1 v s fig 0 9
Figure 9. Upper Handguard Assembly (M16A3, M16A4) 12973021.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0402
FIG. 9
UPPER HANDGUARD
ASSEMBLY (M16A3, M16A4)
12973021
1
PAFZZ
1005-01-453-4226 19200
12973027
REAR HANDGUARD CLAMP .............
UOC:AW4, AZ1
1
2
PAFZZ
5305-01-540-4805 19200
13011435
SLOTTED SCREW ASSEMBLY ..........
UOC:AW4, AZ1
1
3
XAFZZ
19200
12973022
UPPER HANDGUARD .........................
UOC:AW4, AZ1
1
4
PAFZZ
5360-01-540-4806 19200
13012017
FLAT SPRING .......................................
UOC:AW4, AZ1
1
5
PAFZZ
5365-01-540-4807 19200
13012018
SPECIAL SHAPED SPACER ...............
UOC:AW4, AZ1
1
6
PAFZZ
5315-00-826-3251 96906
MS16562-223 SPRING PIN ..........................................
UOC:AW4, AZ1
2
END OF FIGURE
0039-23
TM 9-1005-319-23&P
0039
2
1
2
1 v s fig 1 0
Figure 10. Barrel Stop Assembly (M16A3, M16A4) 12973139.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0403
FIG. 10 BARREL STOP ASSEMBLY
(M16A3, M16A4) 12973139
1
XAFZZ
19200
12973034
BARREL STOP ......................................
UOC:AW4, AZ1
2
PAFZZ
5360-01-452-9636 19200
12973035
HELICAL COMPRESSION
SPRING..................................................
UOC:AW4, AZ1
END OF FIGURE
0039-24
1
1
TM 9-1005-319-23&P
1
2
3
F L A
C A N O
N E W S T
S
0039
N
T S P R
N L Y
Y L E S
P A C E
O T E
I N G
B E U
P E C
R (I T
(I T
S E
I A L
E M
D
E M
4 )
W I T H
S H A P E D
5 ).
4
6
5
1 v s fig 1 1
Figure 11. Upper Handguard Assembly (M4, M4A1) 12973096.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 0404
FIG. 11 UPPER HANDGUARD
ASSEMBLY (M4, M4A1)
12973096
1
PAFZZ
1005-01-453-4226 19200
12973027
REAR HANDGUARD CLAMP .............
UOC:AS1, AY6
1
2
PAFZZ
5305-01-540-4805 19200
13011435
SLOTTED SCREW ASSEMBLY ..........
UOC:AS1, AY6
1
3
XAFZZ
19200
12973097
UPPER HANDGUARD .........................
UOC:AS1, AY6
1
4
PAFZZ
5360-01-540-4808 19200
13012016
FLAT SPRING .......................................
UOC:AS1, AY6
1
5
PAFZZ
5365-01-540-4807 19200
13012018
SPECIAL SHAPED SPACER ...............
UOC:AS1, AY6
1
6
PAFZZ
5315-00-826-3251 96906
MS16562-223 SPRING PIN ..........................................
UOC:AS1, AY6
2
END OF FIGURE
0039-25
TM 9-1005-319-23&P
0039
2
1
3
1 6
4
5
1 5
6
1 4
1 1
1 3
1 2
7
1 0
9
8
M 1 6 A 2
6 A
6 B
1 4
1 3
1 1
7
1 0
9
8
M 1 6 A 3 /M 1 6 A 4 /M 4 /M 4 A 1
1 v s fig 1 2
Figure 12. Upper Receiver Assembly (M16A2) 9349062, (M16A3,
M16A4) 12973011, and (M4, M4A1) 12972675.
0039-26
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 0405
FIG. 12 UPPER RECEIVER
ASSEMBLY (M16A2)
9349062, (M16A3, M16A4)
12973011, AND (M4, M4A1)
12972675
1
PAFZZ
1005-01-134-3621 19200
9349066
INDEX, ELEVATION
(M16A2) ..................................................
UOC:AR8
2
PAFZZ
5305-01-134-3622 19200
9349065
SCREW, INDEX (M16A2).....................
UOC:AR8
3
AFFFF
19200
9349072
REAR SIGHT ASSEMBLY
(M16A2) (FOR ASSY
BREAKDOWN SEE FIG. 14)................
UOC:AR8
4
PAFZZ
3110-00-183-9175 96906
MS19060-4808 BALL, BEARING (M16A2) ...................
UOC:AR8
5
PAFZZ
5360-01-148-1751 19200
9349069
6
PAFZZ
1005-01-134-3701 19200
9349063
1
1
1
1
SPRING, HELICAL, COMPRESSION,
INDEX (M16A2).....................................
UOC:AR8
1
RECEIVER, UPPER
(M16A2) ..................................................
UOC:AR8
1
6A
PAFZZ
1005-01-382-6795 19200
12972670
RECEIVER, UPPER (M4, M4A1).........
UOC: AS1, AY6
6B
PAFZZ
1005-01-454-9880 19200
12973012
RECEIVER, UPPER (M16A3,
M16A4) ...................................................
UOC:AW4, AZ1
1
1
7
PAFZZ
5325-00-999-0864 96906
MS16632-3012 RING, RETAINING, COVER ...............
8
PAFZZ
5315-00-978-1023 19204
8448533
1
PIN, GROOVED, HEADLESS,
COVER ...................................................
1
9
PAFZZ
1005-00-978-1022 19204
8448525
COVER, EJECTION PORT ..................
1
10
PAFZZ
5360-00-978-1025 19204
8448532
SPRING, HELICAL, TORSION,
COVER ...................................................
1
11
PAFZZ
5315-00-840-3812 80205
MS16562-121 PIN, SPRING, FORWARD ASSIST .....
1
12
PAFZZ
5315-00-840-3812 80205
MS16562-121 PIN, SPRING (M16A2)..........................
UOC:AR8
1
13
PAFZZ
5360-00-017-9541 19200
8448540
0039-27
SPRING, HELICAL, COMPRESSION,
FORWARD ASSIST...............................
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
14
15
16
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
PAFFF 1005-01-442-0160 19200
PAFZZ
PAFZZ
5360-01-134-3710 19200
5355-01-135-4972 19200
(5)
PART
NUMBER
9349086
9349070
9349067
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
QTY
FORWARD ASSIST ASSEMBLY
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 13) ..........................................
1
(7)
SPRING, HELICAL, COMPRESSION,
ELEVATION (M16A2) ..........................
UOC:AR8
1
KNOB, ELEVATION
(M16A2) ..................................................
UOC:AR8
1
END OF FIGURE
0039-28
0039
TM 9-1005-319-23&P
0039
1
2
3
4
5
1 v s fig 1 3
Figure 13. Forward Assist Assembly 9349086.
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
GROUP 040501
FIG. 13 FORWARD ASSIST
ASSEMBLY 9349086
1
XAFZZ
19200
9349085
PLUNGER ASSEMBLY........................
1
2
PAFZZ
5315-01-048-9372 19204
8448521-2
PIN, SPRING, PAWL ............................
1
3
PAFZZ
5360-00-523-8084 19200
8448542
SPRING, HELICAL, COMPRESSION,
PAWL .....................................................
1
4
PAFZZ
1005-00-017-9540 19204
8448544
DETENT, PAWL....................................
1
5
PAFZZ
3040-00-017-9539 19204
8448543
PAWL, FORWARD ASSIST..................
1
END OF FIGURE
0039-29
TM 9-1005-319-23&P
3
2 A
1
0039
2
4
5
6
8
5
4
7
Figure 14. Rear Sight Assembly (M16A2) 9349072 and
(M16A3, M16A4, M4, M4A1) 12951026.
0039-30
1 v s fig 1 4
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 040502
FIG. 14 REAR SIGHT ASSEMBLY
(M16A2) 9349072 AND
(M16A3, M16A4, M4, M4A1)
12951026
1
PAFZZ
5315-00-058-6678 96906
MS16562-103 PIN, SPRING, WINDAGE ....................
1
2
PAFZZ
1005-01-134-3631 19200
9349074
BASE, REAR SIGHT.............................
UOC:AR8
1
2A
PAFZZ
1005-01-382-7086 19200
12951028
BASE, REAR SIGHT.............................
UOC: AW4, AZ1, AS1, AY6
1
3
PAFZZ
5305-01-144-1490 19200
9349076
SCREW, EXTERNALLY RE.................
1
4
PAFZZ
5360-01-148-1751 19200
9349069
SPRING, HELICAL, COMPRESSION,
REAR SIGHT .........................................
2
5
PAFZZ
3110-00-183-9175 96906
MS19060-4808 BALL, BEARING...................................
2
6
PAFZZ
1005-01-135-3697 19200
9349075
APERTURE, SIGHT..............................
1
7
PAFZZ
5360-01-381-6183 19200
12011987
SPRING, FLAT, REAR SIGHT.............
1
8
PAFZZ
5355-01-134-3627 19200
9349077
KNOB, WINDAGE ................................
1
END OF FIGURE
0039-31/32 blank
TM 9-1005-319-23&P
0039
3 A
2
1
3
3 0 ,3 0 A ,3 0 B
2 9
8
4
5
9
7
6
1 1
1 0
1 2
2 6
2 7
2 8
1 1
2 5
2 4
1 7
1 2
1 3
1 6
1 6 A
2 3
1 5
1 4
1 8 A
2 2
1 8
2 0
1 9
2 1
M 1 6 A 2 /M 1 6 A 3 /M 1 6 A 4 R I F L E
1 v s fig 1 5 a
Figure 15. Lower Receiver and Buttstock Assembly (M16A2) 9349100,
(M16A3) 12012001, (M16A4) 12598101, (M4) 9390011,
and (M4A1) 12972690 (Sheet 1 of 2).
0039-33
TM 9-1005-319-23&P
0039
3 A
1 A
2 A
3 B
8
3 0 D
4
9
7
5
3 0 C
6
1 0
1 1 A
1 2 A
2 5
2 4
1 7
1 3
1 6
1 6 A
2 3
2 8 A
1 5
1 4
1 8 C
2 2
1 9
1 8 B
2 0
2 1
M 4 /M 4 A 1 C A R B I N E
Figure 15. Lower Receiver and Buttstock Assembly (M16A2) 9349100,
(M16A3) 12012001, (M16A4) 12598101, (M4) 9390011,
and (M4A1) 12972690 (Sheet 2 of 2).
0039-34
1 v s fig 1 5 b
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 05
FIG. 15 LOWER RECEIVER AND
BUTTSTOCK ASSEMBLY
(M16A2) 9349100, (M16A3)
12012001, (M16A4) 12598101,
(M4) 9390011, AND (M4A1)
12972690
1
1A
2
PAFZZ
PAFZZ
PAFZZ
5360-00-992-6665 19204
5360-01-233-8617 19200
1005-00-937-3078 19200
2A
PAFZZ
1005-01-522-0772 19200
3
AFFFF
19200
3A
3B
AFFFF
AFFFF
19204
19200
8448629
9390022
8448615
SPRING, HELICAL, COMPRESSION,
ACTION (M16A2, M16A3, M16A4)......
UOC:AR8, AW4, AZ1
1
SPRING, HELICAL, COMPRESSION
(M4, M4A1).............................................
UOC:AS1, AY6
1
BUFFER ASSEMBLY (M16A2,
M16A3, M16A4) .....................................
UOC:AR8, AW4, AZ1
1
13004468
BUFFER ASSEMBLY (M4, M4A1) ......
UOC:AS1, AY6
9349106
HAMMER ASSEMBLY (M16A2,
M16A4) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 17)................
UOC:AR8, AZ1
8448610
9390032
HAMMER ASSEMBLY (M16A3,
M4A1) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 17)................
UOC:AW4, AY6
HAMMER ASSEMBLY (M4) (FOR
ASSEMBLY BREAKDOWN
SEE FIG. 17) ..........................................
UOC:AS1
1
1
1
1
4
PAFZZ
1005-00-992-6649 19200
8448595
SEAR ......................................................
1
5
PAFZZ
1005-01-225-8339 19200
9381367
SELECTOR, FIRE CONTROL .............
1
6
PAFZZ
5360-00-056-2246 19204
8448633
SPRING, HELICAL, COMPRESSION,
BOLT CATCH ........................................
1
7
PAFZZ
1005-00-056-2247 19204
8448634
PLUNGER, BOLT CATCH ...................
1
8
PAFZZ
1005-00-017-9548 19200
8448628
CATCH, BOLT .......................................
1
9
PAFZZ
5315-00-812-3312 80205
MS16562-119 PIN, SPRING, BOLT CATCH ..............
1
10
PAFZZ
1005-00-056-2201 19204
8448638
1
0039-35
CATCH, MAGAZINE ............................
TM 9-1005-319-23&P
(1)
ITEM
NO.
11
(2)
SMR
CODE
PAFZZ
11A PAFZZ
12
PAFZZ
12A PAFZZ
13
PAFZZ
(3)
(4)
NSN
CAGEC
5360-00-992-6655 19204
5360-00-992-6655 19204
5315-00-992-6654 19204
5315-00-992-6654 19204
5360-00-992-7301 19204
(5)
PART
NUMBER
8448586
8448586
8448585
8448585
8448637
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
SPRING, HELICAL, COMPRESSION,
TAKE DOWN/PIVOT PIN (M16A2,
M16A3, M16A4) .....................................
UOC:AR8, AW4, AZ1
SPRING, HELICAL, COMPRESSION,
PIVOT PIN (M4, M4A1) ........................
UOC:AS1, AY6
PIN, STRAIGHT, HEADLESS,
DETENT, TAKE DOWN PIN
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
PIN, STRAIGHT, HEADLESS
(M4, M4A1).............................................
UOC:AS1, AY6
0039
(7)
QTY
2
1
2
1
SPRING, HELICAL, COMPRESSION,
MAGAZINE CATCH .............................
1
14
PAFZZ
1005-00-992-7302 19204
8448636
BUTTON, MAGAZINE CATCH ...........
1
15
PAFZZ
5315-00-017-9537 19204
8448621
PIN, GROOVED, HEADED
(PIVOT PIN) ..........................................
1
16
PAFZZ
16A PAFZZ
17
18
PAFZZ
AFFFF
18A AFFFF
18B AFFFF
18C AFFFF
5340-01-145-7910 19200
9349114
LEVER, LOCK-RELEASE, SEMI
(M16A2, M16A4, M4) ............................
UOC:AR8, AZ1, AS1
1005-00-999-0406 19200
8448635
DISCONNECTOR (M16A3, M4A1)......
UOC:AW4, AY6
5340-01-144-1499 19200
9349113
LEVER, LOCK-RELEASE, BURST
(M16A2, M16A4, M4) ............................
UOC:AR8, AZ1, AS1
19200
19204
19200
19200
9349115
8448591
12972697
12972698
0039-36
TRIGGER ASSEMBLY (M16A2,
M16A4) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 18)................
UOC:AR8, AZ1
TRIGGER ASSEMBLY (M16A3)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 18) ..........................................
UOC:AW4
TRIGGER ASSEMBLY (M4)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 18) ..........................................
UOC:AS1
TRIGGER ASSEMBLY (M4A1)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 18) ..........................................
UOC:AY6
1
1
1
1
1
1
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
0039
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
19
PAFZZ
1005-01-148-4805 19200
9349127
GRIP, RIFLE, PLASTIC, BLACK ........
1
20
PAFZZ
5310-00-527-3634 80205
MS35335-61
WASHER, LOCK, RIFLE GRIP ...........
1
21
PAFZZ
5305-01-268-1191 88044
SCREW, MACHINE, RIFLE GRIP ......
1
22
PAFZZ
5360-00-992-7292 19204
AN501D416
-18
8448516
SPRING, HELICAL, COMPRESSION,
SAFETY..................................................
1
23
PAFZZ
1005-00-992-6667 19204
8448631
DETENT, SAFETY................................
1
24
PAFZZ
5315-00-992-7309 19204
8448609
PIN, GROOVED, HEADLESS,
TRIGGER AND HAMMER ...................
2
PIN, GROOVED, HEADLESS,
AUTOMATIC SEAR ..............................
1
25
26
27
28
PAFZZ
PAFZZ
PAFZZ
30
5315-00-992-6653 19204
5365-01-267-2169 19200
PAFFF 1005-01-135-4973 19200
28A AFFFF
29
5315-00-992-6650 19204
PAFZZ
XAFFA
30A XAFFA
30B XAFFA
19200
5305-01-147-8585 19200
19200
19200
19200
8448599
8448584
12597640
9349119
12012082
9349128
9349101
12012002
12598102
0039-37
PIN, GROOVED, HEADED
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
1
SPACER, STEPPED (M16A2,
M16A3, M16A4) .....................................
UOC:AR8, AW4, AZ1
1
BUTTSTOCK ASSEMBLY (M16A2,
M16A3, M16A4) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 16)................
UOC:AR8, AW4, AZ1
BUTTSTOCK ASSEMBLY (M4,
M4A1) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 16)................
UOC:AS1, AY6
SCREW, MACHINE, BUTTCAP
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
LOWER RECEIVER AND RECEIVER
EXTENSION ASSEMBLY (M16A2)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 20) ..........................................
UOC:AR8
LOWER RECEIVER AND RECEIVER
EXTENSION ASSEMBLY (M16A3)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 20) ..........................................
UOC:AW4
LOWER RECEIVER AND RECEIVER
EXTENSION ASSEMBLY (M16A4)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 20) ..........................................
UOC:AZ1
1
1
1
1
1
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
30C XAFFA
30D XAFFA
(3)
(4)
NSN
CAGEC
19200
19200
(5)
PART
NUMBER
9390011
12972690
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
LOWER RECEIVER AND RECEIVER
EXTENSION ASSEMBLY (M4)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 20) ..........................................
UOC:AS1
LOWER RECEIVER AND RECEIVER
EXTENSION ASSEMBLY (M4A1)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 20) ..........................................
UOC:AY6
END OF FIGURE
0039-38
0039
(7)
QTY
1
1
TM 9-1005-319-23&P
1
0039
2
4
3
7
6
5
M 1 6 A 2 /M 1 6 A 3 /M 1 6 A 4 R I F L E
8
9
4 A
1 3
1 0
5
1 1
1 2
M 4 /M 4 A 1 C A R B I N E
1 v s fig 1 6
Figure 16. Buttstock Assembly (M16A2, M16A3, M16A4) 9349119 and (M4, M4A1) 12012082.
0039-39 blank/40
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 0501
FIG. 16 BUTTSTOCK ASSEMBLY
(M16A2, M16A3, M16A4)
9349119 AND (M4, M4A1)
12012082
1
2
3
4
PAFZZ
PAFZZ
PAFZZ
XAFZZ
1005-01-520-7064 19200
1005-01-146-7685 19200
5340-00-463-3892 19200
19200
12999220
9349130
8448653
9349121
DOOR ASSEMBLY, THUMB
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
1
PLATE, BUTT, SHOULDER GUN
STOCK (M16A2, M16A3, M16A4)........
UOC:AR8, AW4, AZ1
1
HINGE, ACCESS DOOR, BUTT
PLATE (M16A2, M16A3, M16A4) ........
UOC:AR8, AW4, AZ1
1
BUTTSTOCK (M16A2, M16A3,
M16A4) ...................................................
UOC:AR8, AW4, AZ1
1
4A
PAFZZ
1005-01-459-0734 19200
12012081
BUTTSTOCK (M4, M4A1) ....................
UOC:AS1, AY6
1
5
PAFZZ
1005-00-403-0964 19204
8448652
SWIVEL, SLING, SMALL ....................
1
6
PAFZZ
5315-00-463-3894 19204
8448655
PIN, STRAIGHT, HEADLESS,
ACCESS DOOR (M16A2, M16A3,
M16A4) ...................................................
UOC:AR8, AW4, AZ1
7
8
9
10
11
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5305-01-144-1494 19200
5315-01-233-8608 19200
5360-01-233-8616 19200
1005-01-233-8638 19200
5310-01-233-8626 19200
9349120
9390025
9390027
9390014
9390026
0039-41
1
SCREW, MACHINE, BUTT PLATE
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
1
PIN, SHOULDER, HEADLESS
(M4, M4A1).............................................
UOC:AS1, AY6
1
SPRING, HELICAL, COMPRESSION
(M4, M4A1).............................................
UOC:AS1, AY6
1
LEVER, LOCK-RELEASE
(M4, M4A1).............................................
UOC:AS1, AY6
1
NUT, SELF-LOCKING
(M4, M4A1).............................................
UOC:AS1, AY6
1
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
12
PAFZZ
5315-00-843-9487 80205
MS16562-202 PIN, SPRING (M4, M4A1) ....................
UOC:AS1, AY6
1
13
PAFZZ
5305-01-459-5982 19200
12012083
1
MACHINE SCREW (M4, M4A1) ..........
UOC:AS1, AY6
END OF FIGURE
0039-42
TM 9-1005-319-23&P
0039
4 A
2
3
1
3 A
4
1 A
M 1 6 A 3 /M 4 A 1
M 1 6 A 2 /M 1 6 A 4 /M 4
Figure 17. Hammer Assembly (M16A2, M16A4) 9349106, (M4) 9390032,
and (M16A3, M4A1) 8448610.
0039-43 blank/44
1 v s fig 1 7
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 0502
FIG. 17 HAMMER ASSEMBLY
(M16A2, M16A4) 9349106,
(M4) 9390032, AND
(M16A3, M4A1) 8448610
1
1A
2
3
3A
4
4A
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5360-01-144-1492 19200
5360-00-992-6648 19204
5360-01-136-5471 19200
1005-01-148-0172 19200
3040-01-247-7969 19200
1005-01-134-3630 19200
1005-00-017-9551 19200
9349107
8448611
9349109
9349108
9390031
9349110
8448612
SPRING, HELICAL, TORSION,
HAMMER (M16A2, M16A4, M4)..........
UOC:AR8, AZ1, AS1
1
SPRING, HELICAL, TORSION
(M16A3, M4A1)......................................
UOC:AW4, AY6
1
SPRING, HELICAL, TORSION,
BURST CAM (M16A2, M16A4, M4).....
UOC:AR8, AZ1, AS1
1
CAM, BURST (BLACK)
(M16A2, M16A4)....................................
UOC:AR8, AZ1
1
CAM, CONTROL (NICKEL/SHINY)
(M4).........................................................
UOC:AS1
1
HAMMER AND HAMMER PIN
RETAINER ASSEMBLY
(M16A2, M16A4, M4) ............................
UOC:AR8, AZ1, AS1
HAMMER, FIRING, SMALL
(M16A3, M4A1)......................................
UOC:AW4, AY6
END OF FIGURE
0039-45
1
1
TM 9-1005-319-23&P
0039
1 A
1
2
2
M 1 6 A 2 /M 1 6 A 4
M 4
3
3 A
2
4
M 1 6 A 3 /M 4 A 1
Figure 18. Trigger Assembly (M16A2, M16A4) 9349115, (M16A3) 8448591,
(M4) 12972697, and (M4A1) 12972698.
0039-46
1 v s fig 1 8
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 0503
FIG. 18 TRIGGER ASSEMBLY
(M16A2, M16A4) 9349115,
(M16A3) 8448591, (M4)
12972697, AND (M4A1)
12972698
1
1A
2
3
3A
4
PAFFF 1005-01-219-2402 19200
PAFFF 1005-01-395-4257 19200
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5360-00-992-7308 19204
5360-01-396-0256 19200
5360-00-992-7311 19200
1005-00-992-7307 19204
9392518
12972696
8448593
12972695
8448594
8448592
TRIGGER SUBASSEMBLY
(M16A2, M16A4) (FOR ASSEMBLY
BREAKDOWN SEE FIG. 19)................
UOC:AR8, AZ1
TRIGGER SUBASSEMBLY (M4)
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 19) ..........................................
UOC:AS1
SPRING, HELICAL, TORSION,
TRIGGER ...............................................
1
1
SPRING, HELICAL, COMPRESSION,
DISCONNECT (BLACK) (M4A1) .........
UOC:AY6
1
SPRING, HELICAL, COMPRESSION,
(NICKEL/SHINY) (M16A3) ..................
UOC:AW4
1
TRIGGER (M16A3, M4A1) ...................
UOC:AW4, AY6
END OF FIGURE
0039-47
1
1
TM 9-1005-319-23&P
0039
1 B
1 A
1
2
2
M 4
M 1 6 A 2 /M 1 6 A 4
1 v s fig 1 9
Figure 19. Trigger Subassembly (M16A2, M16A4) 9392518 and (M4) 12972696.
0039-48
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 050301
FIG. 19 TRIGGER SUBASSEMBLY
(M16A2, M16A4) 9392518
AND (M4) 12972696
1
1A
1B
2
PAFZZ
PAFZZ
PAFZZ
XAFZZ
5360-01-135-0353 19200
5360-01-135-0353 19200
5360-01-396-0256 19200
19200
9349116
9349116
12972695
9390736
SPRING, HELICAL, COMP,
DISCONNECT (M16A2, M16A4) .........
UOC:AR8, AZ1
SPRING, HELICAL, COMP,
DISCONNECT (NICKEL/SHINY)
(M4).........................................................
UOC:AS1
SPRING, HELICAL, COMP,
DISCONNECT (BLACK) (M4)..............
UOC:AS1
TRIGGER (M16A2, M16A4, M4) ..........
UOC:AR8, AZ1, AS1
END OF FIGURE
0039-49
2
1
1
1
TM 9-1005-319-23&P
0039
1
2
3
6
6 A
6 B
M 1 6 A 2 /M 1 6 A 3 /M 1 6 A 4 R I F L E
5
4
1 A
7
8
2
3
6 C
6 D
1 1
1 0
9
5
M 4 /M 4 A 1 C A R B I N E
4
1 v s fig 2 0
Figure 20. Lower Receiver and Receiver Extension Assembly
(M16A2) 9349101, (M16A3) 12012002, (M16A4) 12598102,
(M4) 9390011, and (M4A1) 12972690.
0039-50
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 0504
FIG. 20 LOWER RECEIVER AND
RECEIVER EXTENSION
ASSEMBLY (M16A2) 9349101,
(M16A3) 12012002, (M16A4)
12598102, (M4) 9390011, AND
(M4A1) 12972690
1
1A
2
3
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5340-00-992-7297 19200
1005-01-233-8531 19200
5315-00-992-6651 19204
5360-00-992-6652 19200
8448581
9390019
8448582
8448583
EXTENSION, LOWER RECEIVER
(M16A2, M16A3, M16A4)......................
UOC:AR8, AW4, AZ1
1
EXTENSION, LOWER RECEIVER
(M4, M4A1).............................................
UOC:AS1, AY6
1
PIN, SHOULDER, HEADLESS,
BUFFER RETAINER............................
1
SPRING, HELICAL, COMPRESSION,
BUFFER RETAINER............................
1
4
PAFZZ
1005-00-992-7299 19204
8448587
GUARD, TRIGGER ...............................
1
5
PAFZZ
5315-00-058-6081 80205
MS16562-129 PIN, SPRING, TRIGGER GUARD.......
1
6
XAFDA
19200
9349102
RECEIVER (M16A2) .............................
UOC:AR8
1
6A
XAFDA
19200
12012003
RECEIVER (M16A3) .............................
UOC:AW4
1
6B
XAFDA
19200
12598103
RECEIVER (M16A4) .............................
UOC:AZ1
1
6C
XAFDA
19200
9390015
RECEIVER (M4)....................................
UOC:AS1
1
6D
XAFDA
19200
12972652
RECEIVER (M4A1) ...............................
UOC:AY6
1
7
PAFZZ
5310-01-233-8625 19200
9390020
NUT, PLAIN, ROUND (M4, M4A1) .....
UOC:AS1, AY6
1
8
PAFZZ
1005-01-233-8530 19200
9390021
PLATE, RECEIVER END
(M4, M4A1).............................................
UOC:AS1, AY6
1
PIN, GROOVED, HEADED
(M4, M4A1).............................................
UOC:AS1, AY6
1
9
PAFZZ
5315-00-992-6653 19204
8448584
0039-51
TM 9-1005-319-23&P
(1)
ITEM
NO.
10
11
(2)
SMR
CODE
PAFZZ
PAFZZ
(3)
(4)
NSN
CAGEC
5315-00-992-6654 19204
5360-00-992-6655 19204
(5)
PART
NUMBER
8448585
8448586
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
(7)
QTY
PIN, STRAIGHT, HEADLESS
(M4, M4A1).............................................
UOC:AS1, AY6
1
SPRING, HELICAL, COMPRESSION
(M4, M4A1).............................................
UOC:AS1, AY6
1
END OF FIGURE
0039-52
0039
TM 9-1005-319-23&P
0039
1
2
3
4
5
6
1 v s fig 2 1
Figure 21. M16A3, M16A4, M4, and M4A1 Adapter Rail Cover Assemblies.
0039-53 blank/54
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 06
FIG. 21 M16A3, M16A4, M4, AND
M4A1 ADAPTER RAIL
COVER ASSEMBLIES
1
2
3
4
5
6
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
1005-01-453-5386 19200
1005-01-453-5383 19200
1005-01-453-4222 19200
1005-01-453-4221 19200
1005-01-453-4223 19200
1005-01-453-4228 19200
12973132
12973134
12973135
12973136
12973137
12973138
11 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
9 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
6 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
5 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
4 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
2 RIB RAIL COVER ASSEMBLY
(M16A3, M16A4, M4, M4A1) ................
UOC:AW4, AZ1, AS1, AY6
V
NOTE
V: ORDER ADEQUATE SIZE AND
QUANTITY TO COVER ALL
EXPOSED RAILS OF HANDGUARDS.
END OF FIGURE
0039-55
TM 9-1005-319-23&P
0039
1
3
4
5
2
6
1 0
9
7
8
1 v s fig 2 2
Figure 22. Carrying Handle Assembly (M16A3, M16A4, M4, M4A1) 12951011.
0039-56
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 07
FIG. 22 CARRYING HANDLE
ASSEMBLY (M16A3, M16A4,
M4, M4A1) 12951011
1
PAFFF 1005-01-465-0401 19200
12951011
CARRYING HANDLE ASSEMBLY .....
UOC:AW4, AZ1, AS1, AY6
2
PAFZZ
12951021
.HANDLE, GUN CARRYING
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
3
4
5
6
7
8
9
10
AFFFF
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
1005-01-382-7083 19200
19200
5305-01-134-3622 19200
1005-01-382-7089 19200
5355-01-382-6801 19200
5360-01-134-3710 19200
5315-00-840-3812 80205
5360-01-382-6802 19200
3110-00-183-9175 80205
12951026
9349065
.REAR SIGHT ASSEMBLY
(FOR ASSEMBLY BREAKDOWN
SEE FIG. 14)
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
1
1
.SCREW, INDEX
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
.ELEVATING MECHANISM
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
.KNOB
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
.SPRING, HELICAL, COMPRESSION
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
MS16562-121 .PIN, SPRING
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
12951018
12951019
9349070
12951020
.SPRING, HELICAL, COMPRESSION
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
MS19060-4808 .BALL BEARING
(M16A3, M16A4, M4, M4A1) ...............
UOC:AW4, AZ1, AS1, AY6
1
END OF FIGURE
0039-57
TM 9-1005-319-23&P
0039
2
4
3
1 3
5
6
1 2
1
7
1 1
8
1 0
9
Figure 23. Special Tools.
0039-58
1 v s fig 2 3
TM 9-1005-319-23&P
(1)
ITEM
NO.
(2)
SMR
CODE
(3)
(4)
NSN
CAGEC
(5)
PART
NUMBER
(6)
DESCRIPTION AND USABLE ON
CODE (UOC)
0039
(7)
QTY
GROUP 9500
FIG. 23 SPECIAL TOOLS
1
PEFZZ
19204
8426685
MAINTENANCE KIT, GUN DS/GS
SUPPORT MAINTENANCE FOR 5.56
RIFLE, M16 RIFLE SERIES ................
2
2
PAFZZ
4933-01-035-5607 19204
12006359
.CASE, BORE GAGE.............................
2
3
PAFZZ
4933-00-800-7508 19204
8448201
.REFLECTOR TOOL, CHAMBER .......
2
4
PAFZZ
5220-01-075-5004 19200
12620101
.GAGE, PLUG, PLAIN ..........................
2
5
PAFZZ
5220-01-014-8183 19204
8448496
.GAGE, BARREL EROSION
(CHROME BARREL) ...........................
2
6
PAFZZ
5220-00-221-9391 19204
8448202
.GAGE, STRAIGHTNESS.....................
2
7
PAFZZ
5220-00-070-7814 19204
7799734
.GAGE, HEADSPACE ...........................
2
8
PAFZZ
5220-00-070-7815 19204
7799735
.GAGE, FIRING PIN PROTRUSION...
2
9
PAFZZ
4933-00-070-9151 19204
11010032
.FIXTURE, BARREL REMOVAL.........
2
10
PAFZZ
5120-01-505-1677 19200
12997571
.WRENCH, COMBINATION................
2
11
PAFZZ
5220-01-043-9473 19204
12006472
.GAGE, PLUG, TAPER CYLINDER ....
2
12
PAFZZ
5315-01-310-0370 19200
12926769
.KEY, MACHINE...................................
2
13
PAFZZ
5120-01-324-6631 19200
9390035
.WRENCH, SPANNER (M4, M4A1).....
UOC:AS1, AY6
2
END OF FIGURE
END OF WORK PACKAGE
0039-59/60 blank
TM 9-1005-319-23&P
0040
FIELD MAINTENANCE
NATIONAL STOCK NUMBER INDEX
STOCK NUMBER
5315-00-017-9537
3040-00-017-9539
1005-00-017-9540
5360-00-017-9541
1005-00-017-9543
1005-00-017-9546
1005-00-017-9547
1005-00-017-9548
1005-00-017-9551
1005-00-056-2201
5360-00-056-2246
1005-00-056-2247
5315-00-058-6044
5315-00-058-6081
5315-00-058-6678
5320-01-063-7635
5220-00-070-7814
5220-00-070-7815
4933-00-070-9151
1005-00-087-8998
3110-00-183-9175
5220-00-221-9391
1005-00-403-0964
5340-00-463-3892
5315-00-463-3894
5360-00-523-8084
5310-00-527-3634
5315-00-597-5086
5315-00-690-0544
4933-00-800-7508
5315-00-812-3312
5315-00-826-3251
5315-00-840-3812
5315-00-843-9487
1005-00-921-5004
1005-00-937-3078
1005-00-978-1022
5315-00-978-1023
FIG.
15
13
13
12
8
1
3
15
17
15
15
15
7
20
2
14
8
23
23
23
7
2
12
14
22
23
16
16
16
13
15
4
8
23
15
9
11
12
12
22
16
1
15
12
12
ITEM
STOCK NUMBER
15
5
4
13
4
1
1
8
4A
10
6
7
7
5
4
1
5
7
8
9
8
7
4
5
10
6
5
3
6
3
20
4
8
3
9
6
6
11
12
8
12
4
2
9
8
5360-00-978-1025
5360-00-978-1036
4710-00-978-1038
5315-00-979-3930
5360-00-979-3931
5360-00-992-6648
1005-00-992-6649
5315-00-992-6650
5315-00-992-6651
5360-00-992-6652
5315-00-992-6653
5315-00-992-6654
5360-00-992-6655
5360-00-992-6665
1005-00-992-6667
1005-00-992-7283
5305-00-992-7284
1005-00-992-7287
1005-00-992-7288
1005-00-992-7290
1005-00-992-7291
5360-00-992-7292
5315-00-992-7294
5340-00-992-7297
1005-00-992-7299
5360-00-992-7301
1005-00-992-7302
1005-00-992-7307
5360-00-992-7308
5315-00-992-7309
5360-00-992-7311
5360-00-999-0404
5342-00-999-0405
1005-00-999-0406
5325-00-999-0863
5325-00-999-0864
1005-00-999-1509
5220-01-014-8183
4933-01-035-5607
0040-1
FIG.
ITEM
12
7
7
8
8
17
15
15
20
20
15
20
15
15
20
15
15
20
15
15
5
5
4
4
4
4
4
15
3
20
20
15
15
18
18
15
18
6
6
15
7
12
3
23
23
10
9
3
2
3
1A
4
25
2
3
26
9
12
12A
10
11
11A
11
1
23
2
1
1
7
3
6
5
22
3
1
4
13
14
4
2
24
3A
3
2
16A
10
7
2
5
2
TM 9-1005-319-23&P
0040
NATIONAL STOCK NUMBER INDEX - Continued
STOCK NUMBER
5220-01-043-9473
5315-01-048-9372
5320-01-063-7635
5220-01-075-5004
1005-01-134-3621
5305-01-134-3622
1005-01-134-3625
5355-01-134-3627
1005-01-134-3629
1005-01-134-3630
1005-01-134-3631
1005-01-134-3633
1005-01-134-3701
5360-01-134-3710
5360-01-135-0353
1005-01-135-3697
5355-01-135-4972
1005-01-135-4973
5360-01-136-5471
5305-01-144-1490
5360-01-144-1492
5305-01-144-1494
5340-01-144-1499
5340-01-145-7910
1005-01-146-7684
1005-01-146-7685
5305-01-147-8585
1005-01-148-0172
5360-01-148-1751
1005-01-148-4805
1005-01-216-4510
1005-01-219-2402
1005-01-225-8339
1005-01-233-8529
1005-01-233-8530
1005-01-233-8531
5315-01-233-8608
5360-01-233-8616
5360-01-233-8617
5310-01-233-8625
FIG.
23
6
13
8
23
12
12
22
8
2
14
7
17
14
7
12
12
22
19
19
14
12
15
17
14
17
16
15
15
7
16
15
17
2
12
14
15
1
18
15
7
20
20
16
16
15
20
ITEM
STOCK NUMBER
11
1
2
5
4
1
2
4
1
5
8
2
4
2
6
6
15
7
1
1A
6
16
28
2
3
1
7
17
16
4
2
29
3
6
5
4
19
5
1
5
4B
8
1A
8
9
1A
7
5310-01-233-8626
4710-01-233-8637
1005-01-233-8638
3040-01-247-7969
1010-01-264-6517
5365-01-267-2169
5305-01-268-1191
5315-01-310-0370
5120-01-324-6631
1005-01-368-9852
5360-01-381-6183
1005-01-382-6795
5355-01-382-6801
5360-01-382-6802
1005-01-382-7083
1005-01-382-7086
1005-01-382-7089
1005-01-395-4257
5360-01-396-0256
1005-01-441-1619
1005-01-442-0160
5360-01-452-9636
1005-01-453-1633
1005-01-453-1635
1005-01-453-4221
1005-01-453-4222
1005-01-453-4223
1005-01-453-4224
1005-01-453-4225
1005-01-453-4226
1005-01-453-4227
1005-01-453-4228
1005-01-453-5383
1005-01-453-5386
1005-01-453-6655
1005-01-454-1629
1005-01-454-9880
1005-01-459-0734
5305-01-459-5982
1005-01-465-0401
1005-01-471-5456
5340-01-474-2845
5310-01-475-9652
5315-01-484-7071
5305-01-484-7074
0040-2
FIG.
16
7
16
17
8
15
15
23
23
1
14
12
22
22
22
14
22
18
18
19
3
12
10
7
7
21
21
21
7
7
9
11
7
21
21
21
1
7
12
16
16
22
7
8
7
2
2
ITEM
11
3A
10
3A
9
27
21
12
13
5A
7
6A
6
9
2
2A
5
1A
3
1B
5
14
2
15
13
4
3
5
12
11
1
1
14
6
2
1
8
4A
6B
4A
13
1
4C
7
5
12
9
TM 9-1005-319-23&P
STOCK NUMBER
5305-01-484-7075
5360-01-484-7076
5340-01-484-7999
1005-01-484-8000
5325-01-486-7585
1005-01-497-2592
1005-01-505-1035
5120-01-505-1677
1005-01-505-2886
1005-01-520-7064
1005-01-522-0772
5305-01-540-4805
5360-01-540-4806
5365-01-540-4807
5360-01-540-4808
FIG.
2
2
2
1
2
2
3
23
4
16
15
9
11
9
9
11
11
ITEM
3
13
2
7
11
1
4
10
8
1
2A
2
2
4
5
5
4
END OF WORK PACKAGE
0040-3/4 blank
0040
TM 9-1005-319-23&P
0041
FIELD MAINTENANCE
PART NUMBER INDEX
PART NUMBER
AN501D416-18
MS16562-98
MS16562-103
MS16562-106
MS16562-119
MS16562-121
MS16562-129
MS16562-202
MS16562-223
MS16624-3035
MS16626-3137
MS16632-3012
MS19060-4808
MS35335-61
MS39086-93
7799734
7799735
8426685
8448201
8448202
8448496
8448502
8448503
8448504
8448505
8448506
8448507
8448508
8448510
8448511
8448512
8448513
8448515
8448516
8448517
8448518
8448519
8448520
FIG.
15
4
2
14
7
15
12
12
22
20
16
9
11
2
7
12
2
12
14
22
15
8
23
23
23
23
23
23
3
3
3
3
5
5
5
4
4
4
4
4
4
15
1
6
6
6
ITEM
PART NUMBER
21
4
4
1
7
9
11
12
8
5
12
6
6
11
10
7
7
4
5
10
20
8
7
8
1
3
6
5
3
1
2
5
2
3
1
2
1
7
3
6
5
22
1
4
2
3
8448521-2
8448525
8448532
8448533
8448540
8448542
8448543
8448544
8448555
8448567
8448571
8448573
8448574
8448581
8448582
8448583
8448584
8448585
8448586
8448587
8448591
8448592
8448593
8448594
8448595
8448599
8448609
8448610
8448611
8448612
8448615
8448621
8448628
8448629
8448631
8448633
8448634
8448635
8448636
8448637
0041-1
FIG.
6
13
12
12
12
12
13
13
13
7
7
8
8
8
20
20
20
15
20
15
15
20
15
15
20
20
15
18
18
18
15
15
15
15
17
17
15
15
15
15
15
15
15
15
15
15
ITEM
1
2
9
10
8
13
3
5
4
9
3
4
2
3
1
2
3
26
9
12
12A
10
11
11A
11
4
18A
4
2
3A
4
25
24
3A
1A
4A
2
15
8
1
23
6
7
16A
14
13
TM 9-1005-319-23&P
0041
PART NUMBER INDEX - Continued
PART NUMBER
8448638
8448652
8448653
8448655
8448670
8448697
8448712
9349050
9349051
9349054
9349056
9349059
9349062
9349063
9349065
9349066
9349067
9349069
9349070
9349072
9349074
9349075
9349076
9349077
9349085
9349086
9349100
9349101
9349102
9349106
9349107
9349108
9349109
9349110
9349113
9349114
9349115
9349116
9349119
9349120
9349121
9349124
FIG.
15
16
16
16
1
8
7
1
7
8
8
7
7
12
12
22
12
12
2
12
14
12
22
12
14
14
14
2
14
13
12
1
15
20
15
17
17
17
17
15
15
15
19
19
15
16
16
7
ITEM
PART NUMBER
10
5
3
6
4
5
8
3
6
6
1
2
1
6
2
4
1
16
6
5
4
15
7
3
2
6
3
5
8
1
14
6
30
6
3
1
3
2
4
17
16
18
1
1A
28
7
4
4
9349127
9349128
9349130
9381367
9390007
9390009
9390011
9390014
9390015
9390016
9390019
9390020
9390021
9390022
9390025
9390026
9390027
9390031
9390032
9390035
9390736
9392518
11010032
12006359
12006472
12011987
12011996
12012001
12012002
12012003
12012081
12012082
12012083
12597640
12598101
12598102
12598103
12598107
12598617
12620101
12624561
12926769
12951011
12951018
12951019
12951020
12951021
0041-2
FIG.
15
15
16
15
7
8
1
15
16
20
7
20
20
20
15
16
16
16
17
15
23
19
18
23
23
23
14
1
1
15
20
16
15
16
15
1
15
20
7
8
23
1
23
22
22
22
22
22
ITEM
19
29
2
5
4B
6A
6C
30C
10
6C
3A
1A
7
8
1A
8
11
9
3A
3B
13
2
1
9
2
11
7
5A
6A
30A
6A
4A
28A
13
27
6B
30B
6B
4A
9
4
5
12
1
5
6
9
2
TM 9-1005-319-23&P
PART NUMBER
12951026
12951028
12972652
12972670
12972675
12972680
12972690
12972695
12972696
12972697
12972698
12973010
12973011
12973012
12973021
12973022
12973027
12973029
12973034
12973035
12973096
12973097
12973099
12973101
12973132
12973134
12973135
12973136
12973137
12973138
12973139
12991254
12991533
12991850
12991851
FIG.
22
14
20
12
7
1
1
15
18
19
18
15
15
1
7
12
7
9
9
11
7
10
10
7
11
7
1
21
21
21
21
21
21
7
8
7
8
7
ITEM
3
2A
6D
6A
1B
3B
6D
30D
3
1B
1A
18B
18C
3A
1A
6B
11
3
1
1
13
1
2
14
3
15
8
1
2
3
4
5
6
12
7
5
6B
4C
PART NUMBER
12996812
12996813
12996818
12996819
12996820
12996821
12996822
12996823
12996824
12997148
12997571
12999220
13004468
13004786
13004787
13004788
13012016
13012017
13012018
13011435
END OF WORK PACKAGE
0041-3/4 blank
0041
FIG.
1
2
2
2
2
2
2
2
2
1
23
16
15
4
3
1
11
9
9
11
9
11
ITEM
7
1
8
10
13
12
9
2
3
3C
10
1
2A
8
4
2
4
4
5
5
2
2
TM 9-1005-319-23&P
CHAPTER 6
SUPPORTING INFORMATION
FOR
M16 SERIES RIFLES
AND
M4 SERIES CARBINES
TM 9-1005-319-23&P
FIELD MAINTENANCE
REFERENCES
SCOPE
This work package lists all field manuals, forms, miscellaneous publications, technical bulletins, and
technical manuals referenced in this manual.
FIELD MANUALS
FM 3-22.9
Rifle Marksmanship M16A1, M16A2/3, M16A4, and M4 Carbine
FM 4-25.11
First Aid
FORMS
AFTO Form 22
Technical Order System Publications Improvement Report
AFTO Form 105
Inspection, Maintenance, and Firing Data for Ground Weapons
DA Form 2028
Recommended Changes to Publications and Blank Forms
DA Form 2404
Equipment Inspection and Maintenance Worksheet
DA Form 2408-9
Equipment Control Record
DA Form 5988-E
Equipment Inspection and Maintenance Worksheet - Electronic
DD Form 314
Preventive Maintenance Schedule and Record
NAVMC Form 10772
Recommended Changes to Technical Publications
NAVMC 11003
Ordnance Serialized Items Subsidiary Records
SF 361
Transportation Discrepancy Report
SF 364
Report of Discrepancy (ROD)
SF 368
Product Quality Deficiency Report
MISCELLANEOUS PUBLICATIONS
AFI 21-101
Management and Maintenance of Non-Nuclear Munitions
AFI 36-2226
Combat Arms Program
AFJMAN 23-215
Reporting of Supply Discrepancies
AFMAN 44-163(I)
First Aid Manual
AFMAN 91-201
Explosives Safety Standards
0042-1
0042
TM 9-1005-319-23&P
0042
MISCELLANEOUS PUBLICATIONS - Continued
AMC-P 310-9
Equipment Publications Listing
AR 75-1
Malfunctions Involving Ammunition and Explosives
AR 385-40
Accident Reporting and Records
AR 725-50
Requisition, Receipt, and Issue System
AR 750-1
Army Materiel Maintenance Policy
CTA 8-100
Army Medical Department Expendable/Durable Items
CTA 50-909
Field and Garrison Furnishings and Equipment
CTA 50-970
Expendable/Durable Items (Except: Medical, Class V, Repair Parts,
and Heraldic Items)
DA PAM 25-30
Consolidated Army Publications and Forms Index
DA PAM 750-8
The Army Maintenance Management System (TAMMS) Users
Manual
DOD 4160.21-M-1
Defense Demilitarization Manual
SB 746-1
Publications for Packaging Army General Supplies
SC 4933-95-A11
Shop Set, Small Arms: Field Maintenance, Basic, Less Power
SC 5180-95-B71
Sets, Kits, and Outfits for Tool Kit, Small Arms
SPI 00-856-6885
Special Packaging Instructions for M16 Rifle
TECHNICAL BULLETINS
TB MED 524
Occupational and Environmental Health: Control of Hazards to
Health from Laser Radiation
TB 9-1000-247-34
Standards for Overseas Shipment of Small Arms, Aircraft Armament,
Towed Howitzers, Mortars, Recoilless Rifles, Rocket Launchers, and
Associated Fire Control Equipment
TB 43-0002-73
Maintenance Expenditure Limits for FSC Group 10: FSC Classes
1005, 1010, 1015, 1030, 1055, 1090, and 1095
TB 43-0134
Battery Disposition and Disposal
TB 43-180
Interactive Electronic Technical Manual (IETM) for Calibration and
Repair Requirements for the Maintenance of Army Materiel
0042-2
TM 9-1005-319-23&P
0042
TECHNICAL MANUALS/INSTRUCTIONS/ORDERS
TM 9-1005-237-23&P
Organizational and Direct Support Maintenance Manual (Including
Repair Parts and Special Tools List) for Bayonet-Knife, M6, with
Bayonet-Knife Scabbard, M10 (NSN 1095-00-014-0369), BayonetKnife, M7, with Bayonet-Knife Scabbard, M10 (1095-00-017-9701),
and M9 Multipurpose Bayonet System (1005-01-227-1739)
TM 9-1005-319-10
Operator's Manual for Rifle, 5.56 mm, M16A2 W/E (NSN 1005-01128-9936) (EIC: 4GM); Rifle, 5.56 mm, M16A3 (1005-01-357-5112);
Rifle, 5.56 mm, M16A4 (1005-01-383-2872) (EIC: 4F9); Carbine, 5.56
mm, M4 W/E (1005-01-231-0973) (EIC: 4FJ); Carbine, 5.56 mm,
M4A1 (1005-01-382-0953) (EIC: 4GC)
TM 9-1010-221-23&P
Unit and Direct Support Maintenance Manual (Including Repair
Parts and Special Tools List) for Launcher, Grenade, 40mm, M203,
W/E (NSN 1010-00-179-6447) (EIC: 4QB) and Launcher, Grenade,
40mm, M203A1, W/E (1010-01-434-9028) (EIC: 4QH) and Launcher,
Grenade, 40mm, M203A2, W/E (1010-01-495-8511) (EIC: 4QJ)
TM 9-6920-363-12&P
Operator's and Organizational Maintenance Manual (Including
Repair Parts and Special Tools List) for Conversion Kit (Cal. 22
Rimfire Adapter) M261 (NSN 1005-01-010-1561) for Rifle, 5.56-mm,
M16 and M16A1
TM 9-6920-746-12&P
Operator's and Organizational Maintenance Manual (Including
Repair Parts and Special Tools List) M2 Practice Bolt Plastic
Ammunition (NSN 1005-01-184-4041) for Rifle 5.56mm, M16 Series
TM 11-5855-213-23&P
Unit and Direct Support Maintenance Manual (Including Repair
Parts and Special Tools List) for Night Vision Sight, Individual
Served Weapon AN/PVS-4 (NSN 5855-00-629-5334) (EIC: IPJ)
TM 11-5855-306-10
Operator Manual for Monocular Night Vision Device (MNVD)
AN/PVS-14 (NSN 5855-01-432-0524) (EIC: IPX)
TM 11-5855-308-12&P
Operator's and Unit Maintenance Manual (Including Repair Parts
and Special Tools List) Target Pointer Illuminator/Aiming Light
AN/PEQ-2A (NSN 5855-01-447-8992) (EIC: N/A)
TM 11-5855-309-12&P
Operator and Armorer's Maintenance Manual (Including Repair
Parts and Special Tools List) for Thermal Weapon Sight, AN/PAS13A(V)2 (Medium) and AN/PAS-13A(V)3 (Heavy)
TM 11-5855-314-12&P
Operator and Armorer's Maintenance Manual (Including Repair
Parts and Special Tools List) for Thermal Weapon Sight, AN/PAS13A(V)1 (Light)
0042-3
TM 9-1005-319-23&P
0042
TECHNICAL MANUALS/INSTRUCTIONS/ORDERS - Continued
TM 750-244-7
Procedures for Destruction of Equipment in Federal Supply
Classifications 1000, 1005, 1010, 1015, 1020, 1025, 1030, 1055, 1090
and 1095 To Prevent Enemy Use
TO 00-5-1
AF Technical Order System
TO 00-35D-54
Materiel Deficiency Reporting and Investigating System
TO 11A-13-10-7
Storage and Maintenance Procedures for Small Arms Ammunition
TO 11W-1-10
Historical Data Recording of Inspection, Maintenance, and Firing
Data for Ground Weapons
TO 33K-1-100-2
TMDE Calibration Interval Technical Order and Work Unit Code
Reference Guide
END OF WORK PACKAGE
0042-4
TM 9-1005-319-23&P
0043
FIELD MAINTENANCE
MAINTENANCE ALLOCATION CHART (MAC) INTRODUCTION
INTRODUCTION
The Army Maintenance System MAC
This introduction provides a general explanation of all maintenance and repair functions authorized at the
two maintenance levels under the Two-Level Maintenance System concept.
This MAC (immediately following the introduction) designates overall authority and responsibility for the
performance of maintenance functions on the identified end item or component. The application of the
maintenance functions to the end item or component shall be consistent with the capacities and capabilities
of the designated maintenance levels, which are shown on the MAC in column (4) as:
Field - includes three subcolumns, Crew maintenance (C), Service maintenance (O), and Field
maintenance (F).
Sustainment - includes two subcolumns, Below Depot (H) and Depot (D).
The tools and test equipment requirements (immediately following the MAC) list the tools and test
equipment (both special tools and common tool sets) required for each maintenance function as referenced
from the MAC.
The remarks (immediately following the tools and test equipment requirements) contain supplemental
instructions and explanatory notes for a particular maintenance function.
Maintenance Functions
Maintenance functions are limited to and defined as follows:
1.
Inspect. To determine the serviceability of an item by comparing its physical, mechanical, and/or
electrical characteristics with established standards through examination (e.g., by sight, sound, or feel).
This includes scheduled inspection and gagings and evaluation of cannon tubes.
2.
Test. To verify serviceability by measuring the mechanical, pneumatic, hydraulic, or electrical
characteristics of an item and comparing those characteristics with prescribed standards on a
scheduled basis, i.e., load testing of lift devices and hydrostatic testing of pressure hoses.
3.
Service. Operations required periodically to keep an item in proper operating condition; e.g., to clean
(includes decontaminate, when required), to preserve, to drain, to paint, or to replenish fuel, lubricants,
chemical fluids, or gases. This includes scheduled exercising and purging of recoil mechanisms. The
following are examples of service functions:
a.
Unpack. To remove from packing box for service or when required for the performance of
maintenance operations.
b.
Repack. To return item to packing box after service and other maintenance operations.
0043-1
TM 9-1005-319-23&P
0043
Maintenance Functions - Continued
c.
Clean. To rid the item of contamination.
d.
Touch up. To spot paint scratched or blistered surfaces.
e.
Mark. To restore obliterated identification.
4.
Adjust. To maintain or regulate, within prescribed limits, by bringing into proper position, or by
setting the operating characteristics to specified parameters.
5.
Align. To adjust specified variable elements of an item to bring about optimum or desired
performance.
6.
Calibrate. To determine and cause corrections to be made or to be adjusted on instruments of test,
measuring, and diagnostic equipment used in precision measurement. Consists of comparisons of two
instruments, one of which is a certified standard of known accuracy, to detect and adjust any
discrepancy in the accuracy of the instrument being compared.
7.
Remove/Install. To remove and install the same item when required to perform service or other
maintenance functions. Install may be the act of emplacing, seating, or fixing into position a spare,
repair part, or module (component or assembly) in a manner to allow the proper functioning of an
equipment or system.
8.
Replace. To remove an unserviceable item and install a serviceable counterpart in its place.
"Replace" is authorized by the MAC and assigned maintenance level is shown as the third position code
of the Source, Maintenance and Recoverability (SMR) code.
9.
Repair. The application of maintenance services, including fault location/troubleshooting,
removal/installation, disassembly/assembly procedures, and maintenance actions to identify troubles
and restore serviceability to an item by correcting specific damage, fault, malfunction, or failure in a
part, subassembly, module (component or assembly), end item, or system.
NOTE
The following definitions are applicable to the "repair" maintenance function:
Services. Inspect, test, service, adjust, align, calibrate, and/or replace.
Fault location/troubleshooting. The process of investigating and detecting the cause
of equipment malfunctioning; the act of isolating a fault within a system or Unit
Under Test (UUT).
Disassembly/assembly. The step-by-step breakdown (taking apart) of a
spare/functional group coded item to the level of its least component, that is assigned
an SMR code for the level of maintenance under consideration (i.e., identified as
maintenance significant).
Actions. Welding, grinding, riveting, straightening, facing, machining, and/or
resurfacing.
0043-2
TM 9-1005-319-23&P
0043
10.
Overhaul. That maintenance effort (service/action) prescribed to restore an item to a completely
serviceable/operational condition as required by maintenance standards in appropriate technical
publications. Overhaul is normally the highest degree of maintenance performed by the Army.
Overhaul does not normally return an item to like new condition.
11.
Rebuild. Consists of those services/actions necessary for the restoration of unserviceable equipment to
a like new condition in accordance with original manufacturing standards. Rebuild is the highest
degree of materiel maintenance applied to Army equipment. The rebuild operation includes the act of
returning to zero those age measurements (e.g., hours/miles) considered in classifying Army
equipment/components.
Explanation of Columns in the MAC
Column (1) Group Number. Column (1) lists Functional Group Code (FGC) numbers, the purpose of which is
to identify maintenance significant components, assemblies, subassemblies, and modules with the Next
Higher Assembly (NHA).
Column (2) Component/Assembly. Column (2) contains the item names of components, assemblies,
subassemblies, and modules for which maintenance is authorized.
Column (3) Maintenance Function. Column (3) lists the functions to be performed on the item listed in
column (2). (For a detailed explanation of these functions refer to "Maintenance Functions" outlined above).
Column (4) Maintenance Level. Column (4) specifies each level of maintenance authorized to perform each
function listed in column (3), by indicating work time required (expressed as manhours in whole hours or
decimals) in the appropriate subcolumn. This work time figure represents the active time required to
perform that maintenance function at the indicated level of maintenance. If the number or complexity of the
tasks within the listed maintenance function varies at different maintenance levels, appropriate work time
figures are to be shown for each level. The work time figure represents the average time required to restore
an item (assembly, subassembly, component, module, end item, or system) to a serviceable condition under
typical field operating conditions. This time includes preparation time (including any necessary
disassembly/assembly time), troubleshooting/fault location time, and quality assurance time in addition to
the time required to perform the specific tasks identified for the maintenance functions authorized in the
MAC. The symbol designations for the various maintenance levels are as follows:
Field:
C - Crew maintenance
O - Service maintenance
F - Field maintenance
Sustainment:
L - Specialized Repair Activity
H - Below Depot maintenance
D - Depot maintenance
NOTE
The "L" maintenance level is not included in column (4) of the MAC. Functions to
this level of maintenance are identified by a work time figure in the "H" column of
column (4), and an associated reference code is used in the REMARKS column (6).
This code is keyed to the remarks and the SRA complete repair application is
explained there.
0043-3
TM 9-1005-319-23&P
0043
Explanation of Columns in the MAC - Continued
Column (5) Tools and Equipment Reference Code. Column (5) specifies, by code, those common tool sets (not
individual tools), common Test, Measurement and Diagnostic Equipment (TMDE), and special tools, special
TMDE and special support equipment required to perform the designated function. Codes are keyed to the
entries in the tools and test equipment table.
Column (6) Remarks Code. When applicable, this column contains a letter code, in alphabetical order, which
is keyed to the remarks table entries.
Explanation of Columns in the Tools and Test Equipment Requirements
Column (1) Tool or Test Equipment Reference Code. The tool or test equipment reference code correlates
with a code used in column (5) of the MAC.
Column (2) Maintenance Level. The lowest level of maintenance authorized to use the tool or test
equipment.
Column (3) Nomenclature. Name or identification of the tool or test equipment.
Column (4) National Stock Number (NSN). The NSN of the tool or test equipment.
Column (5) Tool Number. The manufacturer's part number, model number, or type number.
Explanation of Columns in the Remarks
Column (1) Remarks Code. The code recorded in column (6) of the MAC.
Column (2) Remarks. This column lists information pertinent to the maintenance function being performed
as indicated in the MAC.
END OF WORK PACKAGE
0043-4
TM 9-1005-319-23&P
0044
FIELD MAINTENANCE
MAINTENANCE ALLOCATION CHART (MAC)
MAINTENANCE ALLOCATION CHART (MAC)
Table 1. MAC for M16 Series Rifles and M4 Series Carbines.
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
(5)
FIELD
GROUP
NUMBER
00
01
02
0201
0202
03
COMPONENT/
ASSEMBLY
M16A2, M16A3,
M16A4 5.56mm
Rifle, and
M4/M4A1 Carbine
SUSTAINMENT
TOOLS
BELOW
AND
MAINTENANCE CREW SERVICE FIELD DEPOT DEPOT EQUIPMENT REMARKS
FUNCTION
C
O
F
H
D
REF CODE
CODE
Inspect
Test
Service
Replace
Overhaul
0.1
Back-Up Iron
Sight
(M16A3/M16A4
and M4/M4A1)
Inspect
Remove/Install
Replace
Repair
0.1
0.1
Bolt and Bolt
Carrier Assembly
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
0.1
Inspect
Test
Service
Remove/Install
Replace
Repair
0.1
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
0.1
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
0.1
Breech Assembly
Bolt
Key and Bolt
Carrier Assembly
Charging Handle
Assembly
(6)
0.2
0.3
0.2
0.3
0.1
2
2, 3
**
0.1
0.1
0.1
0.3
3
3
0.1
0.1
0.1
0.1
1, 2
3
0.1
0.1
2
0.1
0.1
2
3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
**Worktimes are included in DMWR 9-1005-319.
0044-1
1
1, 3
**
3
TM 9-1005-319-23&P
0044
MAINTENANCE ALLOCATION CHART (MAC) - Continued
Table 1. MAC for M16 Series Rifles and M4 Series Carbines - Continued.
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
(5)
(6)
FIELD
GROUP
NUMBER
04
0401
0402
0403
0404
0405
040501
040502
05
COMPONENT/
ASSEMBLY
Upper Receiver
and Barrel
Assembly
SUSTAINMENT
TOOLS
BELOW
AND
MAINTENANCE CREW SERVICE FIELD DEPOT DEPOT EQUIPMENT REMARKS
FUNCTION
C
O
F
H
D
REF CODE
CODE
Inspect
Test
Service
Remove/Install
Replace
Repair
0.1
M16A2/M16A3/
M16A4 Barrel
Assembly and M4/
M4A1 Replacement Barrel and
Front Sight
Assembly
Inspect
Replace
Repair
0.1
Upper Handguard
Assembly
(M16A3/M16A4)
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
Barrel Stop
Assembly
(M16A3/M16A4)
Upper Handguard
Assembly
(M4/M4A1)
0.2
0.1
2
1
0.5
0.5
1, 2
1, 2, 3
0.1
0.3
0.1
Inspect
Remove/Install
Replace
Repair
Inspect
Service
Remove/Install
Replace
Repair
0.2
0.2
0.1
0.1
0.1
1, 2
3
0.1
0.1
0.1
0.2
3
0.1
0.1
0.1
0.1
3
0.1
0.1
0.1
0.2
3
Upper Receiver
Assembly
Inspect
Replace
Repair
0.1
0.5
0.3
1, 2
1, 3
Forward Assist
Assembly
Inspect
Replace
Repair
0.1
0.1
0.1
1, 3
Rear Sight
Assembly
(M16A2)
Inspect
Replace
Repair
0.1
0.3
0.2
1, 3
1, 3
Lower Receiver
and Buttstock
Assembly
Inspect
Test
Service
Repair
0.1
0.2
0044-2
A, B
0.1
0.1
0.2
0.3
2
1, 2, 3
C, D, E
TM 9-1005-319-23&P
0044
Table 1. MAC for M16 Series Rifles and M4 Series Carbines - Continued.
(1)
(2)
(3)
(4)
MAINTENANCE LEVEL
(5)
FIELD
GROUP
NUMBER
0501
COMPONENT/
ASSEMBLY
SUSTAINMENT
TOOLS
BELOW
AND
MAINTENANCE CREW SERVICE FIELD DEPOT DEPOT EQUIPMENT REMARKS
FUNCTION
C
O
F
H
D
REF CODE
CODE
Buttstock
Assembly
Inspect
Remove/Install
Replace
Repair
0.1
0.1
0.1
0.1
0502
Hammer
Assembly
Inspect
Remove/Install
Replace
Repair
0.1
0.1
0.1
0.1
0503
Trigger Assembly
Inspect
Remove/Install
Replace
Repair
0.1
0.1
0.1
0.1
1, 3
1, 3
1, 3
Trigger
Subassembly
(M16A2, M16A4,
and M4)
Inspect
Replace
Repair
0.1
0.1
0.1
1, 3
1, 3
Lower Receiver
and Receiver
Extension
Assembly
Inspect
Test
Repair
0.1
0.1
0.2
2
1, 3
M16A3, M16A4,
M4, and M4A1
Adapter Rail Cover
Assemblies
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
0.1
Inspect
Service
Remove/Install
Replace
Repair
0.1
0.1
0.1
050301
0504
06
07
Carrying Handle
Assembly
(6)
0044-3
3
3
3
0.1
0.1
0.1
0.2
3
0.1
0.1
0.3
0.2
1, 3
1, 3
TM 9-1005-319-23&P
0044
MAINTENANCE ALLOCATION CHART (MAC) - Continued
Table 2. Tools and Test Equipment for M16 Series Rifles and M4 Series Carbines.
(1)
TOOL OR TEST
EQUIPMENT
REFERENCE
CODE
(2)
MAINTENANCE
LEVEL
(3)
(4)
(5)
NOMENCLATURE
NATIONAL
STOCK NUMBER
(NSN)
TOOL
NUMBER
1
(Army Only)
F
Shop Set, Small Arms: Field 4933-00-754-0664
Maintenance, Basic, Less
Power
SC 4933-95-A11
2
(Army Only)
F
Tool and Gage Set, DS/GS
Maintenance for 5.56mm
Rifle, M16 Series
8426685
3
(Army Only)
O
Sets, Kits, and Outfits for
Tool Kit, Small Arms
5180-01-506-8287
SC 5180-95-B71
4
(Air Force Only)
F
Torque Wrench, ft-lb
5120-00-640-6365
A-A-411
5
(Air Force Only)
F
Torque Wrench, in-lb
5120-00-230-6380
T-E-12A
6
(Air Force Only)
F
Trigger Weights
4933-00-647-3696
7274758
Table 3. Remarks for M16 Series Rifles and M4 Series Carbines.
REMARKS
CODE
REMARKS
A
Tool, Front Sight Post Removal and Installation
B
C
D
Depressor, Front Sight Detent
Tool, Pivot Pin Removal
Tool, Pivot Pin Installation
E
Pin, Slave
END OF WORK PACKAGE
0044-4
TM 9-1005-319-23&P
0045
FIELD MAINTENANCE
EXPENDABLE AND DURABLE ITEMS LIST
INTRODUCTION
Scope
This work package lists expendable and durable items that you will need to operate and maintain the
M16A2/M16A3/M16A4 Rifle and the M4/M4A1 Carbine. This list is for information only and is not authority
to requisition the listed items. These items are authorized to you by CTA 50-970, Expendable/Durable Items
(Except Medical, Class V, Repair Parts, and Heraldic Items); CTA 50-909, Field and Garrison Furnishings
and Equipment; or CTA 8-100, Army Medical Department Expendable/Durable Items.
Explanation of Columns in the Expendable/Durable Items List
Column (1) Item No. This number is assigned to the entry in the list and is referenced in the narrative
instructions to identify the item (e.g., Use dry cleaning solvent (WP 0045, item 15)).
Column (2) Level. This column identifies the lowest level of maintenance that requires the listed item
(C = Crew, O = Service, F = Field).
Column (3) National Stock Number (NSN). This is the NSN assigned to the item which you can use to
requisition it.
Column (4) Item Name, Description, Part Number/(CAGEC). This column provides the other information
you need to identify the item. The last line below the description is the part number and the Commercial
and Government Entity Code (CAGEC) (in parentheses).
Column (5) U/I. Unit of Issue (U/I) code shows the physical measurement or count of an item, such as
gallon, dozen, gross, etc.
EXPENDABLE AND DURABLE ITEMS LIST
Table 1. Expendable and Durable Items List.
(1)
(2)
Item
No.
Level
(3)
National
Stock
Number (NSN)
(4)
(5)
Item Name, Description,
Part Number/(CAGEC)
U/I
1
F
8040-00-944-7292
ADHESIVE, KIT
MMM-A-1754 (81348)
KT
2
O
8020-00-244-0153
BRUSH, ARTIST'S: metal ferrule, flat chisel
edge, 7/16 w, 1-1/8 exposed bristle
H-B-241 (81348)
EA
0045-1
TM 9-1005-319-23&P
0045
EXPENDABLE AND DURABLE ITEMS LIST - Continued
Table 1. Expendable and Durable Items List - Continued.
(1)
(2)
Item
No.
Level
(3)
National
Stock
Number (NSN)
(4)
(5)
Item Name, Description,
Part Number/(CAGEC)
U/I
3
F
1005-00-716-2702
BRUSH, CLEANING, SMALL ARMS
7162702 (19205)
EA
4
C
1005-00-903-1296
BRUSH, CLEANING, SMALL ARMS: bore
11686340 (19204)
EA
5
C
1005-00-999-1435
BRUSH, CLEANING, SMALL ARMS:
chamber
8432358 (19204)
EA
6
C
1005-00-494-6602
BRUSH, CLEANING, SMALL ARMS: tooth
8448462 (19204)
EA
7
O
7920-00-205-2401
BRUSH, CLEANING, TOOLS AND PARTS
MILS43871 (81349)
EA
8
O
6850-00-965-2332
CARBON REMOVING COMPOUND
P-C-111 (81348)
GL
9
CLEANER, LUBRICANT, AND
PRESERVATIVE (CLP)
4 oz (118.30 ml) bottle
1 pt (0.47 l) bottle
1 gal. (3.79 l) can
MIL-L-63460 (27412)
O
O
O
9150-01-079-6124
9150-01-054-6453
9150-01-053-6688
10
C
9150-01-102-1473
CLEANER, LUBRICANT, AND
PRESERVATIVE: 1/2 oz (14.79 ml) bottle
MIL-L-63460 (81349)
EA
11
C
9920-00-292-9946
CLEANER, TOBACCO PIPE: cotton turf, wire
core (36 per pkg)
DILLSPIPE cleaner (89855)
EA
12
13
C
O
O
6850-00-224-6656
6850-00-224-6657
6850-00-224-6663
O
5350-00-221-0872
CLEANING COMPOUND, RIFLE BORE
(RBC): small arms bore cleaning solution
2 oz (59.15 ml) bottle
8 oz (236.59 ml) can
1 gal. (3.79 l) can
MIL-PRF-372 (81349)
CLOTH, ABRASIVE
A-A-1206 (58536)
0045-2
EA
EA
EA
OZ
CN
CN
SH
TM 9-1005-319-23&P
0045
Table 1. Expendable and Durable Items List - Continued.
(1)
(2)
Item
No.
Level
14
F
(3)
National
Stock
Number (NSN)
6810-00-244-0290
6810-00-616-9188
(4)
(5)
Item Name, Description,
Part Number/(CAGEC)
U/I
DICHLOROMETHANE, TECHNICAL
5 gal. (18.93 l) pail
600 lb (272.16 kg) drum
ASTM D 4701 (81346)
CN
DR
15
O
6850-00-281-1985
DRY CLEANING SOLVENT
1 gal. (3.79 l) can
A-A-711 (58536)
GL
16
O
8010-00-297-0560
ENAMEL: olive drab no. 3407,
1 gal. (3.79 l) can
TT-E-527 (81348)
GL
17
O
8415-00-823-7458
8415-00-823-7459
8415-00-823-7460
GLOVES, CHEMICAL AND OIL
PROTECTIVE
Size 9
Size 10
Size 11
MIL-DTL-32066 (81348)
PR
PR
PR
18
F
9150-00-754-2595
GREASE, MOLYBDENUM DISULFIDE
MIL-G-21164 (81349)
LB
19
C
1005-01-113-0321
HANDLE SECTION, CLEANING ROD,
SMALL ARMS
8436776 (19204)
EA
20
O
9150-01-260-2534
LUBRICANT, SOLID FILM
16 oz (473.18 ml) spray can
MIL-L-23398 (81349)
OZ
21
C
9150-00-292-9689
LUBRICATING OIL, WEAPONS (LAW)
1 qt (0.95 l) can
MIL-L-14107 (81349)
QT
22
23
C
C
O
O
9150-00-935-6597
9150-00-889-3522
9150-00-687-4241
9150-00-753-4686
O
5340-01-230-3181
LUBRICATING OIL, WEAPONS (LSA):
semifluid
2 oz (59.15 ml) plastic bottle
4 oz (118.30 ml) plastic bottle
1 qt (0.95 l) can
1 gal. (3.79 l) can
MIL-L-46000 (81349)
MOUNTING BRACKET (M4/M4A1 ONLY)
12556036 (19200)
0045-3
OZ
OZ
CN
CN
EA
TM 9-1005-319-23&P
0045
EXPENDABLE AND DURABLE ITEMS LIST - Continued
Table 1. Expendable and Durable Items List - Continued.
(1)
(2)
Item
No.
Level
24
O
8010-00-087-0102
PAINT, ENAMEL, SEMIGLOSS:
paint for blank firing attachment (M15A2)
1 qt can (RED - Rifle)
TT-E-529 (81348)
EA
25
O
8010-01-031-1274
PAINT, ENAMEL, SEMIGLOSS:
paint for blank firing attachment (M23)
1 pt can (YELLOW - Carbine)
TT-E-529 (81348)
EA
26
O
3990-00-795-3595
PAN, WASH (BOX, TOTE)
1211 (94453)
EA
27
F
6850-00-826-0981
PENETRANT KIT
MIL-I-25135 (81349)
KT
28
F
8135-01-019-1691
POLYETHYLENE SHEET
PE88-80-2 (84744)
EA
29
O
1005-01-394-7677
PROTECTOR, RAIL (M16A4, M4/M4A1
ONLY)
12972676 (19200)
EA
30
C
7920-00-205-1711
RAG, WIPING
50 lb (22.68 kg) bundle
A-A-531 (58536)
LB
31
C
1005-00-050-6357
ROD SECTION, CLEANING, SMALL ARMS
(3 required)
8436775 (19204)
EA
32
F
8030-00-670-8553
SEALING COMPOUND
DEVCONF (16059)
KT
O
O
O
6850-01-474-2319
6850-01-474-2317
6850-01-474-2316
C
1005-00-937-2250
(3)
National
Stock
Number (NSN)
33
34
(4)
(5)
Item Name, Description,
Part Number/(CAGEC)
U/I
SOLVENT, GENERAL: Type II
1 gal. (3.79 l) can
5 gal. (18.93 l) pail
55 gal. (208.20 l) drum
MIL-PRF-680 (81349)
SWAB HOLDER SECTION, CLEANING
ROD, SMALL ARMS
11686327 (19204)
0045-4
GL
GL
GL
EA
TM 9-1005-319-23&P
0045
Table 1. Expendable and Durable Items List - Continued.
(1)
(2)
Item
No.
Level
35
C
1005-00-912-4248
SWAB, SMALL ARMS
11686408 (19204)
SH
36
C
6920-01-482-0098
TARGET, 25 METER ZEROING,
M16A2/A3/A4 & M4/M4A1
12988975 (19200)
BX
(3)
National
Stock
Number (NSN)
(4)
(5)
Item Name, Description,
Part Number/(CAGEC)
U/I
END OF WORK PACKAGE
0045-5/6 blank
TM 9-1005-319-23&P
INDEX
WP Sequence No. - Page No.
Subject
A
Abbreviation/Acronym ...........................................................................................
Adapter Rail Cover Assemblies Maintenance
Installation .........................................................................................................
Removal ..............................................................................................................
Repair or Replacement ......................................................................................
Annual Gaging Requirements
Gaging .................................................................................................................
Inspection ...........................................................................................................
Auxiliary Equipment .............................................................................................
WP 0001-6
WP 0026-2
WP 0026-1
WP 0026-1
WP 0027-2
WP 0027-2
WP 0031-1
B
Back-up Iron Sight Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Installation .........................................................................................................
Lubrication .........................................................................................................
Removal ..............................................................................................................
Repair or Replacement ......................................................................................
Barrel Assembly (M16A2) 9349124, (M16A3, M16A4) 12598107,
Replacement Barrel and Front Sight Assembly (M4) 9390007,
(M4A1) 12991851 Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Blank Firing Attachment Maintenance
Installation .........................................................................................................
Removal ..............................................................................................................
Repair or Replacement ......................................................................................
Bolt and Bolt Carrier Assembly Maintenance
Assembly ............................................................................................................
Cleaning .............................................................................................................
Disassembly .......................................................................................................
Inspection - Acceptance and Rejection Criteria ...............................................
Repair or Replacement ......................................................................................
Breech Assembly Bolt Maintenance
Assembly ............................................................................................................
Cleaning .............................................................................................................
Disassembly .......................................................................................................
Inspection - Acceptance and Rejection Criteria ...............................................
Repair or Replacement ......................................................................................
Buttstock Assembly Maintenance
Assembly ............................................................................................................
Cleaning .............................................................................................................
Disassembly .......................................................................................................
Lubrication .........................................................................................................
Repair or Replacement ......................................................................................
INDEX-1
WP 0010-4
WP 0010-3
WP 0010-5
WP 0010-4
WP 0010-1
WP 0010-4
WP 0016-8
WP 0016-2
WP 0016-5
WP 0034-1
WP 0034-3
WP 0034-2
WP 0011-7
WP 0011-2
WP 0011-2
WP 0011-3
WP 0011-6
WP 0012-6
WP 0012-3
WP 0012-2
WP 0012-4
WP 0012-6
WP 0022-4
WP 0022-3
WP 0022-1
WP 0022-4
WP 0022-3
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
C
Carrying Handle Assembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Lubrication .........................................................................................................
Repair or Replacement ......................................................................................
Test and Inspection ............................................................................................
Capabilities and Features .....................................................................................
Characteristics .......................................................................................................
Charging Handle Assembly Maintenance
Assembly ............................................................................................................
Cleaning .............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Checking Unpacked Equipment ............................................................................
Close Quarters Battle Sling Maintenance
Installation .........................................................................................................
Repair or Replacement ......................................................................................
Common Tools and Equipment .............................................................................
Corrosion Prevention and Control (CPC) .............................................................
WP 0037-3
WP 0037-2
WP 0037-3
WP 0037-2
WP 0037-6
WP 0002-1
WP 0002-1
WP 0014-2
WP 0014-2
WP 0014-1
WP 0014-2
WP 0006-1
WP 0034-2
WP 0034-5
WP 0001-7
WP 0001-5
D
Destruction of Army Materiel to Prevent Enemy Use ......................................... WP 0001-5
Disposition - Pre-Embarkation Inspection of Material in Units Alerted for
Overseas Movement ........................................................................................... WP 0029-3
E
Equipment Characteristics, Capabilities, and Features .....................................
Equipment Data .....................................................................................................
Expendable and Durable Items List .....................................................................
Explanation of Column Entries - Preventive Maintenance Checks
and Services Introduction .................................................................................
WP 0002-1
WP 0002-4
WP 0045-1
WP 0007-1
F
Field Manuals .........................................................................................................
Forms ......................................................................................................................
Forward Assist Assembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Lubrication .........................................................................................................
Repair or Replacement ......................................................................................
WP 0042-1
WP 0042-1
WP 0020-2
WP 0020-1
WP 0020-2
WP 0020-2
G
General - Field Troubleshooting Index ................................................................. WP 0004-1
General - Introduction to Repair Parts and Special Tools List ........................... WP 0038-1
INDEX-2
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
G (Cont)
General - Pre-Embarkation Inspection of Material in Units Alerted for
Overseas Movement ...........................................................................................
General - Preventive Maintenance Checks and Services (PMCS) Introduction
General - Service Upon Receipt .............................................................................
General - Theory of Operation ...............................................................................
General Information ..............................................................................................
General Inspection Criteria - Pre-Embarkation Inspection of Material
in Units Alerted for Overseas Movement .........................................................
WP 0029-2
WP 0007-1
WP 0006-1
WP 0003-1
WP 0001-1
WP 0029-3
H
Hammer Assembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
How To Use This Manual ......................................................................................
WP 0023-2
WP 0023-1
WP 0023-1
xi
I
Illustrations of Manufactured Items .....................................................................
Index of Manufactured Items ................................................................................
Installation Instructions ........................................................................................
Introduction - Illustrated List of Manufactured Items ........................................
Introduction to Repair Parts and Special Tools List (RPSTL) ............................
WP 0030-2
WP 0030-1
WP 0006-2
WP 0030-1
WP 0038-1
K
Key and Bolt Carrier Assembly Maintenance
Assembly ............................................................................................................ WP 0013-2
Disassembly ....................................................................................................... WP 0013-1
Repair or Replacement ...................................................................................... WP 0013-2
L
List of Abbreviations/Acronyms ............................................................................
List of Effective Pages/Work Packages .................................................................
Location and Description of Major Components ..................................................
Lock Plate Maintenance
Installation .........................................................................................................
Removal ..............................................................................................................
Repair or Replacement ......................................................................................
Lower Receiver and Buttstock Assembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Inspection - Acceptance and Rejection Criteria ...............................................
Repair or Replacement ......................................................................................
Test and Inspection ............................................................................................
INDEX-3
WP 0001-6
A
WP 0002-2
WP 0032-2
WP 0032-4
WP 0032-4
WP 0021-12
WP 0021-2
WP 0021-10
WP 0021-12
WP 0021-21
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
L (Cont)
Lower Receiver and Receiver Extension Assembly (M16A2) 9349101,
(M16A3) 12012002, (M16A4) 12598102, (M4) 9390011, and (M4A1)
12972690 Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Lubrication Instructions ........................................................................................
WP 0025-6
WP 0025-1
WP 0025-4
WP 0008-27
M
Maintenance Allocation Chart (MAC) ..................................................................
Maintenance Allocation Chart (MAC) Introduction ............................................
Maintenance Forms, Records, and Reports ..........................................................
Malfunction/Symptom Index - Field Troubleshooting Index ..............................
Miscellaneous Publications ...................................................................................
Model Numbers and Equipment Names ..............................................................
M12 Storage Rack Maintenance
Installation .........................................................................................................
WP 0044-1
WP 0043-1
WP 0001-4
WP 0004-1
WP 0042-1
WP 0001-4
WP 0036-1
N
National Stock Number Index ............................................................................... WP 0040-1
Nomenclature Cross-Reference List ..................................................................... WP 0001-6
P
Packaging ...............................................................................................................
Part Number Index ................................................................................................
PMCS Procedures ...................................................................................................
Pre-Embarkation Inspection of Material in Units Alerted for
Overseas Movement ...........................................................................................
Preparation for Storage or Shipment ...................................................................
Preventive Maintenance Checks and Services, Including
Lubrication Instructions ....................................................................................
Preventive Maintenance Checks and Services (PMCS) Introduction .................
Principles of Operation ..........................................................................................
Processing Unpacked Equipment .........................................................................
Purpose of Equipment ............................................................................................
Purpose - Pre-Embarkation Inspection of Material in Units Alerted for
Overseas Movement ...........................................................................................
WP 0028-1
WP 0041-1
WP 0008-1
WP 0029-1
WP 0001-5, WP 0028-1
WP 0008-1
WP 0007-1
WP 0003-2
WP 0006-1
WP 0001-4
WP 0029-1
Q
Quality of Material ................................................................................................. WP 0001-7
INDEX-4
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
R
References ...............................................................................................................
Repair Parts ............................................................................................................
Repair Parts List
Adapter Rail Cover Assemblies ........................................................................
Back-up Iron Sight Assembly ...........................................................................
Barrel Assembly (M16A2, M16A3, M16A4) and Replacement
Barrel and Front Sight Assembly (M4, M4A1) ...........................................
Barrel Stop Assembly (M16A3, M16A4) ...........................................................
Bolt and Bolt Carrier Assembly ........................................................................
Breech Assembly Bolt ........................................................................................
Buttstock Assembly ...........................................................................................
Carrying Handle Assembly ...............................................................................
Charging Handle Assembly ...............................................................................
Forward Assist Assembly ..................................................................................
Hammer Assembly .............................................................................................
Key and Bolt Carrier Assembly ........................................................................
Lower Receiver and Buttstock Assembly .........................................................
Lower Receiver and Receiver Extension Assembly .........................................
Rear Sight Assembly (M16A2) ..........................................................................
Rifle, 5.56mm (M16A2, M16A3, M16A4) and Carbine,
5.56mm (M4, M4A1) .....................................................................................
Special Tools .......................................................................................................
Trigger Assembly ...............................................................................................
Trigger Subassembly .........................................................................................
Upper Handguard Assembly (M16A3, M16A4) ...............................................
Upper Handguard Assembly (M4, M4A1) ........................................................
Upper Receiver and Barrel Assembly ..............................................................
Upper Receiver Assembly ..................................................................................
Reporting Equipment Improvement Recommendations (EIR) ...........................
Rifle, 5.56mm (M16A2) 9349000; Rifle, 5.56mm (M16A3) 12012000;
Rifle, 5.56mm (M16A4) 12973001; Carbine, 5.56mm (M4) 9390000;
and Carbine, 5.56mm (M4A1) 12972700 Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Stowage ..............................................................................................................
Test and Inspection ............................................................................................
INDEX-5
WP 0042-1
WP 0001-7
WP 0039-54
WP 0039-6
WP 0039-20
WP 0039-24
WP 0039-8
WP 0039-10
WP 0039-40
WP 0039-56
WP 0039-14
WP 0039-29
WP 0039-44
WP 0039-13
WP 0039-33
WP 0039-50
WP 0039-30
WP 0039-2
WP 0039-58
WP 0039-46
WP 0039-48
WP 0039-23
WP 0039-25
WP 0039-15
WP 0039-26
WP 0001-4
WP 0009-3
WP 0009-2
WP 0009-2
WP 0009-16
WP 0009-3
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
S
Scope - General Information ..................................................................................
Scope - Introduction to Repair Parts and Special Tools List ...............................
Scope - Pre-Embarkation Inspection of Material in Units Alerted for
Overseas Movement ...........................................................................................
Scope - References ..................................................................................................
Service upon Receipt of Materiel ...........................................................................
Shipment or Issue - Pre-Embarkation Inspection of Material in Units
Alerted for Overseas Movement .......................................................................
Special Tools, TMDE, and Support Equipment ...................................................
Supporting Information for Repair Parts, Special Tools, TMDE,
and Support Equipment ....................................................................................
WP 0001-4
WP 0038-1
WP 0029-1
WP 0042-1
WP 0006-1
WP 0029-2
WP 0001-7
WP 0001-7
T
Table of Contents ...................................................................................................
Technical Bulletins ................................................................................................
Technical Manuals/Instructions/Orders ...............................................................
Top Sling Adapter Maintenance
Installation .........................................................................................................
Removal ..............................................................................................................
Repair or Replacement ......................................................................................
Trigger Assembly and Trigger Subassembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Troubleshooting Index - Field ...............................................................................
Troubleshooting Procedures - Field ......................................................................
Type of Manual .......................................................................................................
ii
WP 0042-2
WP 0042-3
WP 0033-1
WP 0033-3
WP 0033-3
WP 0024-2
WP 0024-1
WP 0024-2
WP 0004-1
WP 0005-1
WP 0001-4
U
Unpacking ...............................................................................................................
Upper Handguard Assembly (M4, M4A1) Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
Upper Handguard Assembly and Barrel Stop Assembly (M16A3,
M16A4) Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Repair or Replacement ......................................................................................
INDEX-6
WP 0006-1
WP 0018-3
WP 0018-2
WP 0018-3
WP 0017-3
WP 0017-1
WP 0017-3
TM 9-1005-319-23&P
INDEX - Continued
WP Sequence No. - Page No.
Subject
U (Cont)
Upper Receiver and Barrel Assembly (M16A2) 9349050,
(M16A3, M16A4) 12973010, and (M4, M4A1) 12972680 Maintenance
Assembly ............................................................................................................
Cleaning .............................................................................................................
Disassembly .......................................................................................................
Inspection - Acceptance and Rejection Criteria ...............................................
Repair or Replacement ......................................................................................
Test and Inspection ............................................................................................
Upper Receiver Assembly and Rear Sight Assembly Maintenance
Assembly ............................................................................................................
Disassembly .......................................................................................................
Lubrication .........................................................................................................
Repair or Replacement ......................................................................................
Test and Inspection ............................................................................................
WP 0015-13
WP 0015-7
WP 0015-2
WP 0015-8
WP 0015-10
WP 0015-22
WP 0019-7
WP 0019-2
WP 0019-7
WP 0019-5
WP 0019-12
W
Warning Summary ................................................................................................. a
INDEX-7/8 blank
Use Part II (reverse) for Repair Parts and
Special Tool Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
RECOMMENDED CHANGES TO
PUBLICATIONS
AND BLANK FORMS
DATE
Date you filled out
this form
For use of this form, see AR 25-30; the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code)
FROM: (Activity and location) (Include ZIP Code)
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
Your mailing address
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint Manual for M16 Series Rifle and M4 Series
Carbine
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
00091
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
The part number for the M16A2 rifle is incorrect in the work package title.
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
Your Name
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
Your Signature
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
Your address
DATE
Date you filled out this
form
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4
Series Carbine
PAGE
NO.
COLM
NO.
LINE
NO.
NATIONAL STOCK
NUMBER
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
Your Name
REFERENCE
NO.
FIGURE
NO.
ITEM
NO.
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
Your Signature
USAPPC V3.00
Use Part II (reverse) for Repair Parts and
Special Tool Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
RECOMMENDED CHANGES TO
PUBLICATIONS
AND BLANK FORMS
DATE
For use of this form, see AR 25-30; the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code)
FROM: (Activity and location) (Include ZIP Code)
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4 Series
Carbine
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
DATE
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4
Series Carbine
PAGE
NO.
COLM
NO.
LINE
NO.
NATIONAL STOCK
NUMBER
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
REFERENCE
NO.
FIGURE
NO.
ITEM
NO.
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
USAPPC V3.00
Use Part II (reverse) for Repair Parts and
Special Tool Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
RECOMMENDED CHANGES TO
PUBLICATIONS
AND BLANK FORMS
DATE
For use of this form, see AR 25-30; the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code)
FROM: (Activity and location) (Include ZIP Code)
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4 Series
Carbine
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
DATE
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4
Series Carbine
PAGE
NO.
COLM
NO.
LINE
NO.
NATIONAL STOCK
NUMBER
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
REFERENCE
NO.
FIGURE
NO.
ITEM
NO.
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
USAPPC V3.00
Use Part II (reverse) for Repair Parts and
Special Tool Lists (RPSTL) and Supply
Catalogs/Supply Manuals (SC/SM).
RECOMMENDED CHANGES TO
PUBLICATIONS
AND BLANK FORMS
DATE
For use of this form, see AR 25-30; the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code)
FROM: (Activity and location) (Include ZIP Code)
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4 Series
Carbine
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
FIGURE
NO.
TABLE
NO.
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
DATE
AMSTA-LC-LMPP / TECH PUBS, TACOM-RI
1 Rock Island Arsenal
Rock Island, IL 61299-7630
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER
DATE
TITLE
TM 9-1005-319-23&P
28 November 2008
Field Maint. Manual for M16 Series Rifle and M4
Series Carbine
PAGE
NO.
COLM
NO.
LINE
NO.
NATIONAL STOCK
NUMBER
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
REFERENCE
NO.
FIGURE
NO.
ITEM
NO.
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
USAPPC V3.00
By Order of the Secretary of the Army:
GEORGE W. CASEY, JR.
General, United States Army
Chief of Staff
Official:
JOYCE E. MORROW
Administrative Assistant to the
Secretary of the Army
0831107
DISTRIBUTION: To be distributed in accordance with the Initial Distribution Number (IDN) 400020 requirements
for TM 9-1005-319-23&P.
THE METRIC SYSTEM AND EQUIVALENTS
LINEAR MEASURE
SQUARE MEASURE
1 Centimeter = 10 Millimeters = 0.01 Meter = 0.3937 Inch
1 Decimeter = 10 Centimeters = 3.94 Inches
1 Meter =10 Decimeters = 100 Centimeters
= 1000 Millimeters = 39.37 Inches
1 Dekameter = 10 Meters = 32.8 Feet
1 Hectometer =10 Dekameters = 328.08 Feet
1 Kilometer =10 Hectometers = 1000 Meters
= 0.621 Mile = 3,280.8 Feet
Millimeters = Inches times 25.4
Inches = Millimeters divided by 25.4
1 Sq Centimeter = 100 Sq Millimeters = 0.155 Sq Inch
1 Sq Decimeter = 100 Sq Centimeters = 15.5 Sq Inches
1 Sq Meter (Centare) = 10 Sq Decimeters
= 10,000 Sq Centimeters = 10.764 Sq Feet
1 Sq Dekameter (Are) = 100 Sq Meters = 1,076.4 Sq Feet
1 Sq Hectometer (Hectare) = 100 Sq Dekameters
= 2.471 Acres
1 Sq Kilometer = 100 Sq Hectometers
= 1,000,000 Sq Meters = 0.386 Sq Mile
WEIGHTS
CUBIC MEASURE
1 Centigram = 10 Milligrams = 0.154 Grain
1 Decigram = 10 Centigrams = 1.543 Grains
1 Gram = 0.001 Kilogram = 10 Decigrams
=1000 Milligrams = 0.035 Ounce
1 Dekagram = 10 Grams = 0.353 Ounce
1 Hectogram = 10 Dekagrams = 3.527 Ounces
1 Kilogram = 10 Hectograms = 1000 Grams
= 2.205 Pounds
1 Quintal = 100 Kilograms = 220.46 Pounds
1 Metric Ton = 10 Quintals = 1000 Kilograms
= 1.1 Short Tons
1 Cu Centimeter = 1000 Cu Millimeters = 0.061 Cu Inch
1 Cu Decimeter = 1000 Cu Centimeters = 61.02 Cu Inches
1 Cu Meter = 1000 Cu Decimeters
= 1,000,000 Cu Centimeters= 35.31 Cu Feet
LIQUID MEASURE
1 Milliliter = 0.001 Liter = 0.034 Fluid Ounce
1 Centiliter = 10 Milliliters = 0.34 Fluid Ounce
1 Deciliter = 10 Centiliters = 3.38 Fluid Ounces
1 Liter = 10 Deciliters = 1000 Milliliters
= 33.82 Fluid Ounces
1 Dekaliter = 10 Liters = 2.64 Gallons
1 Hectoliter = 10 Dekaliters = 26.42 Gallons
1 Kiloliter = 10 Hectoliters = 264.18 Gallons
TEMPERATURE
5/9 (qF - 32q) = qC
(9/5 x qC) + 32q = qF
-35q Fahrenheit is equivalent to -37q Celsius
0q Fahrenheit is equivalent to -18q Celsius
32q Fahrenheit is equivalent to 0q Celsius
90q Fahrenheit is equivalent to 32.2q Celsius
100q Fahrenheit is equivalent to 38q Celsius
212q Fahrenheit is equivalent to 100q Celsius
APPROXIMATE CONVERSION FACTORS
TO CHANGE
TO
MULTIPLY BY
Inches ..........................
Feet..............................
Yards ...........................
Miles ............................
Square Inches .............
Square Feet .................
Square Yards...............
Square Miles ...............
Acres ............................
Cubic Feet ...................
Cubic Yards.................
Fluid Ounces ...............
Pints ............................
Quarts..........................
Gallons ........................
Ounces .........................
Pounds.........................
Short Tons ...................
Pound-Feet ..................
Pounds-Inches.............
Pounds per Square Inch..
Ounce-Inches...............
Miles per Gallon..........
Miles per Hour ............
Centimeters........................ 2.540
Meters................................. 0.305
Meters................................. 0.914
Kilometers .......................... 1.609
Square Centimeters ........... 6.451
Square Meters.................... 0.093
Square Meters.................... 0.836
Square Kilometers ............. 2.590
Square Hectometers .......... 0.405
Cubic Meters ...................... 0.028
Cubic Meters ...................... 0.765
Milliliters.......................... 29.573
Liters .................................. 0.473
Liters .................................. 0.946
Liters .................................. 3.785
Grams ............................... 28.349
Kilograms ........................... 0.454
Metric Tons ........................ 0.907
Newton-Meters................... 1.356
Newton-Meters............... 0.11375
Kilopascals ......................... 6.895
Newton-Meters............. 0.007062
Kilometers per Liter .......... 0.425
Kilometers per Hour .......... 1.609
TO CHANGE
TO
MULTIPLY BY
Centimeters .................
Meters..........................
Meters..........................
Kilometers ...................
Square Centimeters ....
Square Meters .............
Square Meters .............
Square Kilometers ......
Square Hectometers....
Cubic Meters ...............
Cubic Meters ...............
Milliliters.....................
Liters ...........................
Liters ...........................
Liters ...........................
Grams ..........................
Kilograms ....................
Metric Tons .................
Newton-Meters............
Kilopascals ..................
Kilometers per Liter ...
Kilometers per Hour ...
qFahrenheit .................
qCelsius........................
Inches.................................. 0.394
Feet ..................................... 3.280
Yards................................... 1.094
Miles ................................... 0.621
Square Inches..................... 0.155
Square Feet ...................... 10.764
Square Yards...................... 1.196
Square Miles....................... 0.386
Acres ................................... 2.471
Cubic Feet......................... 35.315
Cubic Yards ........................ 1.308
Fluid Ounces ...................... 0.034
Pints.................................... 2.113
Quarts................................. 1.057
Gallons................................ 0.264
Ounces ................................ 0.035
Pounds ................................ 2.205
Short Tons .......................... 1.102
Pound-Feet ......................... 0.738
Pounds per Square Inch..... 0.145
Miles per Gallon ................. 2.354
Miles per Hour ................... 0.621
qCelsius..............qC = (qF-32)x5/9
qFahrenheit ......qF = (9/5xqC)+32
PIN: 060514-000
">