Makita G4300L Owner`s manual

Makita G4300L Owner`s manual
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ01
WARNING :
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects or other reproductive
harm.
NOTICE
FEDERAL EMISSION COMPONENT DEFECT WARRANTY and CALIFORNIA
EMISSION CONTROL WARRANTY are applicable to only those engines/
generators complied with EPA (Environmental Protection Agency) and CARB
(California Air Resources Board) emission regulations in the U.S.A.
US
GB
GB
GB
NOTICE
To the engines/generators exported to and used in the countries other than the
U.S.A., warranty service shall be performed by the distributor in each country in
accordance with the standard Makita engine/generator warranty policy as applicable.
GB
GB
GB
GB
GB
GB
AIR INDEX
GB
To show compliance with California emission regulations, a hangtag has been
provided displaying the Air Index level and durability period of this engine.
GB
The Air Index level defines how clean an engine’s exhaust is over a period of
time. A bar graph scaled from “0” (most clean) to “10” (least clean) is used to
show an engine’s Air Index level. A lower Air Index level represents cleaner
exhaust from an engine.
The period of time (in hours) that the Air Index level is measured is known as
the durability period. Depending on the size of the engine, a selection of time
periods can be used to measure the Air Index level (see below).
Descriptive Term
Applicable to Emissions Durability Period
Moderate
-
50 hours (engine from 0 to 65 cc)
125 hours (engine greater than 65 cc)
Intermediate
-
125 hours (engine from 0 to 65 cc)
250 hours (engine greater than 65 cc)
Extended
-
300 hours (engine from 0 to 65 cc)
500 hours (engine greater than 65 cc)
Notice : This hangtag must remain on this engine or piece of equipment, and
only be removed by the ultimate purchaser before operation.
GB
GB
GB
GB
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ02
FEDERAL EMISSIONS COMPONENT DEFECT WARRANTY
EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE – This emission warranty is applicable in all States, except the
State of California.
Makita U.S.A. Inc., La Mirada, California, (herein “MAKITA”) warrant(s) to the initial retail purchaser and each subsequent owner, that this
Nonroad engine (herein “engine”) has been designed, built, and equipped to conform at the time of initial sale to all applicable regulations of
the U.S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this
engine to fail to conform with EPA regulations during its warranty period.
For the components listed under PARTS COVERED, the Makita Factory Service Center or Service Center authorized by MAKITA will, at no
cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA
regulations.
US
GB
EMISSISON COMPONENT DEFECT WARRANTY PERIOD
OWNER’S WARRANTY RESPONSIBILITIES
The warranty period for this engine begins on the date of sale to the
initial purchaser and continues for a period of 2 years.
As the engine owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. MAKITA
recommends that you retain all receipts covering maintenance on
your engine, but MAKITA cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all
scheduled maintenance.
PARTS COVERED
GB
Listed below are the parts covered by the Emission Components
Defect Warranty. Some of the parts listed below may require
scheduled maintenance and are warranted up to the first scheduled
replacement point for that part.
GB
(1) Fuel Metering System
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
(i) Carburetor and internal parts (and/or pressure regulator or
fuel injection system).
(ii) Air/fuel ratio feedback and control system, if applicable.
(iii) Cold start enrichment system, if applicable.
(iv) Regulator assy (gaseous fuel, if applicable)
(2) Air Induction System
(i) Intake manifold, if applicable
As the engine owner, you should however be aware that MAKITA
may deny warranty coverage if your engine or a part has failed due
to abuse, neglect, improper maintenance or unapproved
modifications.
You are responsible for presenting your engine to the nearest
Makita Factory Service Center or Service Center authorized by
MAKITA when a problem exists.
If you have any questions regarding your warranty rights and
responsibilities, you should contact the Makita Warranty Department
at 1-800-4-MAKITA for the information.
(ii) Air filter.
(3) Ignition System
(i) Spark plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system, if applicable.
(4) Exhaust manifold, if applicable
(5) Miscellaneous Items Used in Above Systems
(i) Electronic controls, if applicable
(ii) Hoses, belts, connectors, and assemblies.
(iii) Filter lock assy (gaseous fuel, if applicable)
OBTAINING WARRANTY SERVICE
To obtain warranty service, take your engine to the nearest Makita
Factory Service Center or Service Center authorized by MAKITA .
Bring your sales receipts indicating date of purchase for this engine.
The Makita Factory Service Center or Service Center authorized by
MAKITA will perform the necessary repairs or adjustments within a
reasonable amount of time and furnish you with a copy of the repair
order. All parts and accessories replaced under this warranty become
the property of MAKITA.
WHAT IS NOT COVERED
*Conditions resulting from tampering, misuse, improper adjustment
(unless they were made by the Makita Factory Service Center or
Service Center authorized by MAKITA during a warranty repair),
alteration, accident, failure to use the recommended fuel and oil, or
not performing required maintenance services.
*The replacement parts used for required maintenance services.
*Consequential damages such as loss of time, inconvenience, loss
of use of the engine or equipment, etc.
*Diagnosis and inspection charges that do not result in warrantyeligible service being performed.
*Any non-authorized replacement part, or malfunction of authorized
parts due to use of non-authorized parts.
THINGS YOU SHOULD KNOW ABOUT THE EMISSION
CONTROL SYSTEM WARRANTY MAINTENANCE AND
REPAIRS
You are responsible for the proper maintenance of the engine. You
should keep all receipts and maintenance records covering the
performance of regular maintenance in the event questions arise.
These receipts and maintenance records should be transferred to
each subsequent owner of the engine. MAKITA reserves the right to
deny warranty coverage if the engine has not been properly
maintained. Warranty claims will not be denied, however, solely
because of the lack of required maintenance or failure to keep
maintenance records.
MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION
CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY
ANY REPAIR ESTABLISHMENT OR INDIVIDUAL;
HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY
THE MAKITA FACTORY SERVICE CENTER OR SERVICE
CENTER AUTHORIZED BY MAKITA . THE USE OF PARTS THAT
ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY
TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS
OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A
BEARING ON THE OUTCOME OF A WARRANTY CLAIM.
If other than the parts authorized by MAKITA are used for
maintenance replacements or for the repair of components affecting
emission control, you should assure yourself that such parts are
warranted by their manufacturer to be equivalent to the parts
authorized by MAKITA in their performance and durability.
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ03
HOW TO MAKE A CLAIM
All repair qualifying under this limited warranty must be performed by a Makita Factory Service Center or Service Center authorized by MAKITA . In
the event that any emission-related part is found to be defective during the warranty period, you shall notify Makita Warranty Department at 1-800-4MAKITA and you will be advised of the appropriate warranty service dealer or service providers where the warranty repair can be performed. A list
of the Factory Service Center locations and phone numbers is provided below for your convenience.
ARIZONA
3707 E.Broadway Rd., Ste.6
Phoenix, AZ 85040
(602) 437-2850
MISSOURI
9876 Watson Rd.
St.Louis, MO 63126-2221
(314) 909-9889
CALIFORNIA
41850 Christy St.
Fremont, CA 94538-5107
(510)657-9881
NEBRASKA
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
14930 Northam St.
La Mirada, CA 90638-5753
(714)522-8088
NEVADA
3375 S. Decatur Blvd., Suites22-24
Las Vegas, NV 89102
(702) 368-4277
1970 Fulton Ave.
Sacramento, CA 95825
(916)482-5197
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858)278-4471
16735 Saticoy St.,Ste. 105
Van Nuys, CA 91406
(818)782-2440
COLORADO
11839 E.51st Ave.
Denver, CO 80239-2709
(303) 371-2850
FLORIDA
750 East Sample Rd.
Pompano Beach, FL 33064
(954)781-6333
GEORGIA
4680 River Green Parkway NW
Duluth, GA 30096
(770) 476-8911
ILLINOIS
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
MARYLAND
7397 Washington Boulevard ,
Suite 104
Elkridge, MD 21075
(410) 796-4401
MASSACHUSETTS
232 Providence Highway
Westwood, MA 02090
(781) 461-9754
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
NEW JERSEY
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
NEW YORK
4917 Genessee St.
Cheektowaga, NY 14225
(716) 685-9503
OREGON
828 19th Ave., N. W.
Portland, OR 97209
(503) 222-1823
PENNSYLVANIA
1904 Babcock Blvd.
Pittsburgh, PA 15209
(412)822-7370
PUERTO RICO
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
TENNESSEE
1120 Elm Hill Pike Suite 170
Nashville, TN 37210
(615)248-3321
TEXAS
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
WISCONSIN
Lincoln Plaza Shopping Ctr.
2245 S. 108th St.
West Allis, WI 53227
(414) 541-4776
US
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ04
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
(This warranty does not apply in any other state.)
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and Makita U.S.A., Inc. (herein “MAKITA”) are pleased to explain the emission control warranty on your
2003 and later small off-road engine (herein “engine”). In California, new engine must be designed, built and equipped to meet the State's
stringent anti-smog standards. MAKITA must warrant the emission control system on your engine for the periods of time listed below provided
there has been no abuse, neglect or improper maintenance of your engine.
Your emission control system includes parts such as the carburetor or fuel injection systems, the ignition system and the catalytic converter.
Also included are the hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, MAKITA will repair your engine at no cost to you including diagnosis, parts and labor.
MANUFACTURER'S WARRANTY COVERAGE:
The 2003 and later engines are warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or
replaced by MAKITA.
US
GB
GB
GB
GB
OWNER'S WARRANTY RESPONSIBILITIES:
-As the engine owner, you are responsible for the performance of the required maintenance listed in your Owner's Manual. MAKITA
recommends that you retain all receipts covering maintenance on your engine, but MAKITA cannot deny warranty solely for the lack of
receipts or for your failure to ensure the performance of all scheduled maintenance.
-As the engine owner, you should be aware, however, that MAKITA may deny you warranty coverage if your engine or a part has failed
due to abuse, neglect, improper maintenance or unapproved modifications.
-You are responsible for presenting your engine to a MAKITA service center as a problem exists. The warranty repairs should be
completed in a reasonable time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a Makita Factory Service Center Manager
nearest you. A list of the Factory Service Center locations and phone numbers is provided below for your convenience.
GB
LIMITED WARRANTY
- California Only -
GB
GB
GB
GB
GB
GB
GB
MAKITA , a distributor of small off-road equipment in the U.S., warrants to the owner of 2003and later engines that the engine has been
designed, built, and equipped at the time of manufacture so as to conform with the applicable regulations of the California Air Resources
Board and, (2) is free from defects in materials and workmanship which may cause it to fail to conform with those regulations as applicable
according to the terms and conditions stated below.
WARRANTY PERIOD
This warranty period begins on the date which the engine is
delivered to the original retail purchaser and ends two years after
that date. During this two year period MAKITA warrants to the
original retail purchaser and each subsequent purchaser that the
engine is free from defect in material and workmanship that can
cause the failure of a warranted emission-related part.
GB
GB
GB
(3) Ignition System
(i) Spark plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system, if applicable.
(4) Exhaust manifold, if applicable
(5) Miscellaneous Items Used in Above Systems
(i) Electronic controls, if applicable
WHAT IS COVERED UNDER THIS WARRANTY
(ii) Hoses, belts, connectors, and assemblies.
Repair and/or replacement of any warranted emission-related part will
be performed at no charge provided the work is performed at an
authorized warranty station. There will also be no charge for any
diagnostic labor performed at an authorized warranty station which
leads to the determination that a warranted emission-related part is
defective.
(iii) Filter lock assy (gaseous fuel, if applicable)
Any warranted part which is not scheduled for replacement as required
maintenance, or which is scheduled only for regular inspection to the
effect of "repair or replace as necessary" shall be warranted for the
warranty period. Any warranted part which is scheduled for replacement
as required maintenance shall be warranted for the period of time up to
the first scheduled replacement of that part. This warranty shall apply
only towards the repair, replacement, and/or adjustment of the
component parts listed below.
EMISSION-RELATED PARTS COVERED UNDER THIS
WARRANTY
(1) Fuel Metering System
(i) Carburetor and internal parts
(and/or pressure regulator or fuel injection system).
(ii) Air/fuel ratio feedback and control system, if applicable.
(iii) Cold start enrichment system, if applicable.
(iv) Regulator assy (gaseous fuel, if applicable)
(2) Air Induction System
(i) Intake manifold, if applicable
(ii) Air filter.
If it is determined by an authorized warranty station that other
engine components have been damaged due to the failure of a
warranted emission-related part during the warranty period, MAKITA
will repair and/or replace the necessary components.
WHAT IS NOT COVERED UNDER THIS WARRANTY
This warranty does not cover any emission-related part which
malfunctions, fails, or is damaged due to alterations and/or
modifications such as changing, adding, or removing parts.
When an engine is being serviced under warranty, MAKITA and any of
its authorized dealers, distributors, or warranty stations shall not be
liable for any loss of use of the engine, for any damage to goods, or
loss of time or inconvenience. This limited warranty also does not
apply to any emission-related part which malfunctions, fails, or is
damaged due to failure to follow the maintenance and operating
instructions specified in the 2003 and later Owner's Manual including.
(a) Improper maintenance of any warranted emission-related part.
(b) Improper installation, adjustment, or repair of the engine or any
warranted emission-related part unless performed by a factory
authorized warranty station.
(c) Failure to use recommended fuel as specified in the 2003 and
later Owner's Manual.
(d) Repairs and diagnosis performed outside of an authorized
warranty station.
(e) Use of parts which are not authorized by MAKITA.
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ05
MAINTENANCE SCHEDULE
The engine owner is responsible for having all scheduled inspection and maintenance services performed at the intervals specified in the
2003 and later Owner's Manual and to retain records of these services as having been performed. These records should be transferred to
each subsequent owner of the engine. MAKITA cannot deny a claim solely because there are no records of scheduled maintenance,
however, a warranty claim may be denied if the failure to perform the scheduled maintenance and inspection resulted in the failure of a
warranted emission-related part.
As a minimum, the engine owner is responsible for the scheduled inspection and maintenance described below which are based on the
procedures described in the Owner's Manual.
PROCEDURE
INTERVAL
1)
2)
3)
4)
: Initial 20 hours and every 100 hours afterward
: Every 50 hours
: Every 200 hours
: Every 200 hours
Change engine oil
Clean air cleaner (element)
Replace air cleaner element
Clean and adjust spark plug and electrodes
Note: More frequent maintenance may be necessary under dusty, dirty or severe conditions.
REPAIR AND REPLACEMENT OF EMISSION-RELATED PARTS
It is recommended that only engine replacement parts which have been authorized and approved by MAKITA should be used in the
performance of any warranty maintenance or repairs of emission-related parts. These replacement parts will be provided at no charge if the
part is still under warranty.
US
GB
GB
HOW TO FILE A WARRANTY CLAIM AND WHERE TO GET WARRANTY SERVICES
Contact the nearest Makita Factory Service Center Manager to determine the appropriate location where the required warranty services are
to be performed. A list of the Factory Service Center locations and phone numbers are provided below for your convenience.
41850 Christy St.
Fremont, CA 94538-5107
(510)657-9881
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858)278-4471
14930 Northam St.
La Mirada, CA 90638-5753
(714)522-8088
16735 Saticoy St.,Ste. 105
Van Nuys, CA 91406
(818)782-2440
GB
GB
GB
GB
GB
GB
GB
1970 Fulton Ave.
Sacramento, CA 95825
(916)482-5197
GB
GB
GB
GB
GB
GB
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ06
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ1
FOREWORD
Thank you very much for purchasing a MAKITA GENERATOR.
This manual covers operation and maintenance of the MAKITA GENERATOR.
Please take a moment to familiarize yourself with the proper operation and maintenance procedures in order
to maximize the safe and efficient use of this product.
Keep this owner’s manual at hand, so that you can refer to it at any time.
Due to constant efforts to improve our products, certain procedures and specifications are subject to change
without notice.
When ordering spare parts, always give us the MODEL, PRODUCTION NUMBER (PROD No.) and
SERIAL NUMBER (SER No.) of your Product.
Please fill in the following blanks after checking the production number on your product.
(Location of label is different depending on the product model.)
US
GB
GB
GB
GB
GB
GB
GB
PROD No. / SER No. (Label)
GB
GB
GB
GB
GB
GB
CONTENTS
GB
GB
1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2. COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. PRE-OPERATION CHECKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. OPERATING PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. WATTAGE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. SPARK ARRESTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
7. MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
8. "HOW-TO" MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9. PREPARATION FOR STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
10. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
11. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
12. WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
NOTE Please refer to the illustrations on the back page of the front cover or back cover
for Fig. 1 to 6 indicated in the sentence.
1
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ2
1. SAFETY PRECAUTIONS
Please make sure you review each precaution carefully.
Pay special attention to statement preceded by the following words.
WARNING “WARNING” indicates a strong possibility of severe personal injury or loss
of life if instructions are not followed.
CAUTION
“CAUTION” indicates a possibility of personal injury or
equipment damage if instructions are not followed.
WARNING
Do not operate the generator near gasoline or gaseous fuel because of the potential
US danger of explosion or fire.
GB Do not fill the fuel tank with fuel while the engine is running. Do not smoke or use open
flame near the fuel tank. Be careful not to spill fuel during refueling. If fuel is spilt, wipe
GB it off and let dry before starting the engine.
GB
GB
WARNING
Do not place in flammables near the generator.
GB Be careful not to place fuel, matches, gunpowder, oily cloths, straw, trash, or any other in flammables near
GB
GB
the generator.
WARNING
GB Do not operate the generator inside a room, cave, tunnel, or other
insufficiently ventilated area. Always operate it in a well-ventilated area,
GB otherwise the engine may become overheated, and the poisonous carbon
GB monoxide gas contained in the exhaust gases will endanger human lives.
Keep the generator at least 1 meter (3 feet) away from any structure or
1m
GB building during use.
GB If the generator must be used indoors, the area must be well-ventilated and
GB
GB
GB
1m
extreme caution must be taken regarding the discharge of exhaust gases.
WARNING
Do not enclose the generator nor cover it with a box.
The generator has a built-in forced air cooling system, and may become overheated if it is enclosed.
If generator has been covered to protect it from the weather during non use, be sure to remove it and keep
it well away from the area during generator use.
WARNING
Operate the generator on a level surface.
It is not necessary to prepare a special foundation for the generator.
However, the generator will vibrate on an irregular surface, so choose a level place without surface
irregularities.
If the generator is tilted or moved during operation, fuel may spill and / or the generator may tip over, causing
a hazardous situation.
Proper lubrication cannot be expected if the generator is operated on a steep incline or slope. In such a case,
piston seizure may occur even if the oil is above the upper level.
WARNING
Pay attention to the wiring or extension cords from the generator to the connected device.
If the wire is under the generator or in contact with a vibrating part, it may break and
possibly cause a fire, generator burnout, or electric shock hazard.
Replace damaged or worn cords immediately.
2
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ3
WARNING
Do not operate in rain, in wet or damp conditions, or with wet hands.
The operator may suffer severe electric shock if the generator is wet due to rain or snow.
WARNING
If wet, wipe and dry it well before starting. Do not pour water directly over the generator, nor wash it with
water.
WARNING
Be extremely careful that all necessary electrical grounding procedures are followed during each and every
use. Failure to do so can be fatal.
WARNING
Do not contact the generator to a commercial power line. Connection to a commercial
power line may short circuit the generator and ruin it or cause electric shock hazard. Use
the transfer switch for connecting to domestic circuit.
WARNING
No smoking while handling the battery. The battery emits flammable hydrogen gas,
which can explode if exposed to electric arcing or open flame.
Keep the area well-ventilated and keep open flames/sparks away when handling the battery.
US
GB
GB
GB
GB
GB
GB
GB
GB
GB
WARNING
Engine becomes extremely hot during and for some time after operation. Keep
combustible materials well away from generator area.
Be very careful not to touch any parts of the hot engine especially the muffler area or
serious burns may result.
GB
GB
GB
GB
WARNING
Keep children and all bystanders at a safe distance from work areas.
GB
GB
WARNING
It is absolutely essential that you know the safe and proper use of the power tool or appliance that you intend
to use. All operators must read, understand and follow the tool/appliance owners manual. Tool and appliance
applications and limitations must be understood. Follow all directions given on labels and warnings. Keep all
instruction manuals and literature in a safe place for future reference.
WARNING
Use only "LISTED" extension cords.
When a tool or appliance is used outdoors, use only extension cords marked "For Outdoor Use". Extension
cords, when not in use should be stored in a dry and well ventilated area.
WARNING
Always switch off generator's no fuse breaker and disconnect tools or appliances when not in use, before
servicing, adjusting, or installing accessories and attachments.
3
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ4
Symbols and Meanings
In accordance with the European requirements (eec Directives),the specified symbols as shown in the
following table are used for the products and this instruction manual.
Read the operator's instruction manual.
Fire, open light and smoking
prohibited.
Stay clear of the hot surface.
Caution, risk of electric shock.
Exhaust gas is poisonous.
Do not operate in an unventilated room.
Do not connect the generator to
the commercial power lines.
US
GB
Stop the engine before refueling.
GB
GB
GB
GB
GB
GB
ON
(power and Engine)
IN-position of a
bistable push control
Engine start
(Electric start)
OFF
(power and Engine)
Protective earth
(ground)
Engine stop
Alternating current
Fuse
Diesel fuel
Direct current
Engine oil
Fast
Plus ;
positive polarity
Add oil
Slow
Minus ;
negative polarity
Battery charging
condition
OUT-position of a
bistable push control
Choke ;
cold starting aid
GB
GB
GB
GB
GB
GB
GB
GB
Pr
4
Rated power (kW)
COP
Continuous power
COS
r
Rated power factor
fr
Rated frequency (Hz)
Ur
Rated voltage (V)
Ir
Rated current (A)
H max
Maximum site altitude
above sea-level (m)
T max
Maximum ambient
temperature ( )
m
Mass (kg)
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ5
2. COMPONENTS (See Fig. 1)
NOTE
Please refer to the illustrations on the back page of
the front cover or back cover for Fig. 1 to 6
indicated in the sentence.
5W
10W
Single grade
20W
#20
#30
q CONTROL PANEL
#40
w FRAME
e FUEL GAUGE
r FUEL TANK
t RECOIL STARTER (HANDLE)
y EXHAUST OUTLET
Multigrade
Ambient
temperature
e,r
r)
2. CHECK ENGINE FUEL (See Fig. 2-e
u TANK CAP
WARNING
i FUEL STRAINER
o AIR CLEANER
!0 SPARK PLUG CAP
!1 OIL DRAIN PLUG
!2 OIL GAUGE (OIL FILLER)
3. PRE-OPERATION CHECKS
(See Fig. 2)
q,w
w)
1. CHECK ENGINE OIL (See Fig. 2-q
Do not refuel while smoking or near open
flame or other such potential fire hazards.
Otherwise fire accident may occur.
■
■
■
Remove oil filler cap and check the engine oil
level.(See Fig. 2-q)
q OIL GAUGE
w OIL FILLER
e UPPER LEVEL
r LOWER LEVEL
If oil level is below the lower level line, refill with
suitable oil (see table) to upper level line.
Do not screw in the oil filler cap when
checking oil level.(See Fig. 2-w)
q UPPER LEVEL
w LOWER LEVEL
Change oil if contaminated.
(See "How-To" Maintenance.)
Oil capacity :
Model
Upper level
G2800L . . . . . . . . 0.6 liters
G3200L . . . . . . . . 0.6 liters
G4300L . . . . . . . . 1.0 liters
Recommended engine oil:
Use 4-stroke automotive detergent oil of API service class
SE or higher grade (SG, SH or SJ is recommended).
SAE 10W-30 or 10W-40 is recommended for
general, all-temperature use. If single viscosity oil is
used, select the appropriate viscosity for the
average temperature in your area.
Fuel tank capacity :
G2800L . . . . . . . . 10.8 liters
G3200L . . . . . . . . 10.8 liters
G4300L . . . . . . . . 12.8 liters
WARNING
Make sure you review each warning in
order to prevent fire hazard.
■
■
GB
GB
w FULL (F)
Be sure to use the fuel filter screen on the fuel
filter neck.(See Fig. 2-e)
q FUEL FILTER SCREEN
w TANK CAP
■
GB
q EMPTY (E)
■
■
GB
GB
If fuel level is low, refill with unleaded
automotive gasoline.
■
US
Check fuel level at fuel level gauge.(See Fig. 2-r)
■
Before checking or refilling oil, be sure generator is
located on stable and level surface with engine stopped.
■
10W-30
10W-40
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
Do not refill tank while engine is
running or hot.
Close fuel cock before refueling with fuel.
Be careful not to admit dust, dirt, water
or other foreign objects Into fuel.
Wipe off spilt fuel thoroughly before
starting engine.
Keep open flames away.
3. CHECKING COMPONENT PARTS
Check following items before starting engine:
■
Fuel leakage from fuel hose, etc.
■
Bolts and nuts for looseness.
■
Components for damage or breakage.
■
Generator not resting on or against any
adjacent wiring.
5
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ6
4. CHECK GENERATOR SURROUNDINGS.
WARNING
CAUTION
Make sure you review each warning in
order to prevent fire hazard.
■
■
■
■
US
■
GB
GB
GB
■
■
GB
Keep area clear of in flammables or
other hazardous materials.
Keep generator at least 3 feet (1 meter)
away from buildings or other structures.
Only operate generator in a dry, well
ventilated area.
Keep exhaust pipe clear of foreign
objects.
Keep generator away from open flame.
No smoking!
Keep generator on a stable and level
surface.
Do not block generator air vents with
paper or other material.
GB 5. GROUNDING THE GENERATOR
GB
■
GB
GB
GB
GB
GB
GB
GB
GB
GB
To ground the generator to the earth, connect
the grounding lug of the generator to the
grounding spike driven into the earth or to the
conductor which has been already grounded
to the earth. (See Fig. 2-t)
q GROUNDING SPIKE
■
If such grounding conductor or grounding
electrode is unavailable, connect the
grounding lug of the generator to the
grounding terminal of the using electric tool or
appliance. (See Fig. 2-y)
■
■
Do not connect defective appliances
including lines and plugs.
Be sure appliances are not connected
to generator when starting up.
Starting the generator with an
appliance connected could result in
damage to the generator and/or
appliance and in personal injury.
(c) Pull the starter handle slowly until passing the
compression point (resistance will be felt), then
return the handle to its original position and pull
briskly. (See Fig. 3-w)
q RECOIL STARTER HANDLE
w PULL BRISKLY
(d)After starting, allow the starter handle to return to
its original position with the handle still in your hand.
NOTE
When engine fails to start after several attempts,
repeat the starting procedures mentioned above with
the engine switch placed at "
" (RUN) position.
(e) After 20 to 30 seconds of warm-up is completed,
turn the engine switch to "
" (RUN) position.
(See Fig. 3-e)
q"
" (CHOKE)
w"
" (RUN)
(f) Make sure the pilot lamp is on.
This indicates that the generator is properly
q GROUND TERMINAL
operating.
4. OPERATING PROCEDURES
4)
(See Fig. 3,4
1. STARTING THE GENERATOR
CAUTION
Check the oil level before each operations
as outlined on page 5.
(a) Make sure the appliance is disconnected.
(b)Turn engine switch to "
"(CHOKE) position.
(When engine is warm or temperature is high,
start engine with the switch at "
" (RUN)
position.) (See Fig. 3-q)
q"
6
" (STOP)
w"
" (CHOKE)
NOTE
■
If the pilot lamp is off, Set the AC breaker
to "ON" position.
■
If no generating condition is found out,
please consult nearest Makita factory or
authorized service center.
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ7
2. USING ELECTRIC POWER
WARNING
■
Make sure that the appliance is switched OFF before connecting it to the generator.
■
Do not move the generator while it is running.
■
Be sure to ground the generator if the connected appliance is grounded. Failure to
ground unit may lead to electrical shock.
(1) CONTROL PANEL
G2800L / G3200L
1
2
3
US
GB
GB
GB
GB
6
5
GB
GB
G4300L
1
2
3
GB
4
GB
GB
GB
GB
GB
GB
6
5
GB
GB
CONTROL PANEL
q PILOT LAMP
r AC RECEPTACLES (30A)
w AC CIRCUIT BREAKER
t GROUND TERMINAL
e AC RECEPTACLES (20A)
y ENGINE SWITCH
q,w
w)
(2) AC APPLICATION (See Fig. 4-q
(a) Make sure the pilot lamp is turned on.
(b) Turn off the switch(es) of the electrical appliance(s) before connecting to the generator.
(c) Insert the plug(s) of the electrical appliance(s) into the receptacle. (See Fig. 4-q)
7
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ8
■
Check the amperage of the receptacles used referring to TABLE 1, and be sure not to take a current
exceeding the specified amperage.
■
Be sure that the total wattage of all appliances dose not exceed the rated output of the generator.
Style
US
Ampere Receptacle AC plug
Up to 20A
NEMA
5-20R
NEMA GFCI (Ground Fault
5-20R Circuit Interrupter)
Receptacle, duplex
Up to 30A
NEMA
5-30R
NEMA
Locking Receptacle
5-30R
GB
GB
TABLE 1
GB
GB
WARNING
■
To take power out from the TWIST LOCK RECEPTACLE, insert the plug into the
w)
receptacle, and turn it clockwise to the lock position. (See Fig. 4-w
■
Be sure to ground the generator if the connected electrical device is grounded.
GB
GB
Description
GB
GB
NOTE
GB
When the no fuse breaker turns off during operation, the generator is over loaded or the appliance is
GB
defective.
GB
Stop the generator immediately, check the appliance and / or generator for overloading, and have repaired
GB
as necessary by Makita factory or authorized service center.
GB (d) Turn on the switch of the appliance.
GB
GB
3. STOPPING THE GENERATOR
(a) Turn off the power switch of the electric equipment and unplug the cord from receptacle of the generator.
(b) Allow the engine about 3 minutes to cool down at no load before stopping.
(c) Turn the engine switch to the position "
q"
" (RUN)
w"
" (STOP). (See Fig. 4-e)
" (STOP)
r)
4. OIL SENSOR (See Fig. 4-r
q OIL SENSOR
(a) The oil sensor detects the fall in oil level in the crankcase and automatically stops the engine when the oil
level falls below a predetermined level.
(b) When engine has stopped automatically, switch off generator's no fuse breaker, and check the oil level.
Refill engine oil to the upper level as instructed on page 5 and restart the engine.
(c) If the engine does not start by usual starting procedures, check the oil level.
CAUTION
Do not remove OIL SENSOR PROBE when refilling with oil.
Remove oil filler cap on the opposite side of carburetor.
8
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ9
5. WATTAGE INFORMATION
Some appliances need a "surge" of energy when starting.
This means that the amount of electrical power needed to start the appliance may exceed the amount needed to
maintain its use.
Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz, amperage (amps)
and electrical power needed to run the appliance or tool.
Check with your nearest dealer or service center with questions regarding power surge of certain appliances
or power tools.
■
Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is
needed to maintain use.
■
Loads such as fluorescent lamps require 1.2 to 2 times the indicated wattage during start-up.
■
Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.
■
Electrical motors require a large starting current. Power requirements depend on the type of motor and
its use. Once enough "surge" is attained to start the motor, the appliance will require only 50% to 30%
of the wattage to continue running.
US
■
Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example,
a 5000 watt generator can power a 1800 to 4000 watt electrical tool.
■
Loads such as submersible pumps and air compressors require a very large force to start. They need 3
to 5 times the normal running wattage in order to start.
For example, a 5000 watt generator would only be able to drive a 1000 to 1700 watt pump.
GB
GB
GB
GB
GB
GB
GB
GB
NOTE
GB
The following wattage chart is general guide only. Refer to your specific appliance for
correct wattage.
GB
To determine the total wattage required to run a particular electrical appliance or tool, multiply the voltage
figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps)
information can be found on a name plate which is normally attached to electrical appliances and tools.
GB
GB
GB
GB
GB
Applicable Wattage (W)
Applications
G2800L
G3200L
G4300L
60Hz
Incandescent lamp, Heater
approx. 2400
approx. 2700
approx. 3700
Fluorescent lamp, Electric tool
approx. 1200
approx. 1400
approx. 1900
Mercury lamp
approx. 800
approx. 1000
approx. 1600
Pump, Compressor
approx. 500
approx. 550
approx. 800
9
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ10
VOLTAGE DROP IN ELECTRIC EXTENSION CORDS
When a long electric extension cord is used to connect an appliance or tool to the generator, a certain
amount of voltage drop or loss occurs in the extension cord which reduces the effective voltage available for
the appliance or tool.
The chart below has been prepared to illustrate the approximate voltage loss when an extension cord of 300 feet
(approx. 100 meters) is used to connect an appliance or tool to the generator.
Allowable No.of strands
Resistance
current
/ strands dia.
Current Amp.
US
mm2
No.
A
No./mm
Ω/100m
GB
0.75
18
7
30/0.18
2.477
2.5V 8V 12.5V ─
GB
1.27
16
12
50/0.16
1.486
1.5V 5V 7.5V 12V 15V 18V
GB
2.0
14
17
37/0.26
0.952
1V
GB
3.5
12 to 10
23
45/0.32
0.517
─
GB
5.5
10 to 8
35
70/0.32
0.332
─
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
10
1A
3A
3V
5A
10A 12A 15A
─
─
─
─
8V
10V 12V 15V
1.5V 2.5V 4V
5V 6.5V 7.5V
1V
5V
8A
2V 2.5V 3.5V 4V
5V
Voltage drop
Nominal A.W.G.
cross
Gauge
section
No.
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ11
6. SPARK ARRESTER
In a dry or wooded area, it is recommendable to use the prodoct with a spark arrester. Some areas require the
use of a spark arrester. Please check your local laws and regulations before operating your prodoct.
The spark arrester must be cleaned regularly to keep it functioning as designed.
A clogged spark arrester :
■
Prevents the flow of exhaust gas
■
Reduces engine output
■
Increases fuel consumption
■
Makes starting difficult
If the engine has been running, the muffler and the spark arrester will be very hot. Allow the muffler to cool
before cleaning the spark arrester.
US
GB
How to remove the spark arrester
1. Remove the flange bolts from the muffler cover and
remove the muffler cover.
2. Remove the special screw from the spark arrester
and remove the spark arrester from the muffler.
GB
SPARK
ARRESTER
SCREEN
GB
GB
TAIL SCREEN
GB
MUFFLER
SCREW
TAIL SCREEN COVER
GB
GB
GB
GB
GB
GB
GB
GB
GB
Clean the spark arrester screen
SPARK ARESSTER SCREEN
GB
Use a brush to remove carbon deposits from the spark
arrester screen.
Be careful to avoid damaging the screen.
The spark arrester must be free of breaks and holes.
Replace the spark arrester if it is damaged.
Install the spark arrester, and muffler protector in the
reverse order of disassembly.
11
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ12
7. MAINTENANCE SCHEDULE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION CONTROL DEVICES
AND SYSTEMS MAY BE PERFORMED BY ANY NON-ROAD ENGINE REPAIR
ESTABLISHMENT OR INDIVIDUAL.
DAILY INSPECTION
Before running the generator, check the following service items:
Safe surroundings
Leakage of gasoline and engine oil
US
Enough clean engine oil
GB
AC terminals for damage
GB
GB
GB
Enough gasoline
GB
Excessive vibration,noise
GB
GB
Clean air cleaner element
GB
Loose or broken bolts and nuts
GB
GB
GB
GB
GB
GB
GB
PERIODIC MAINTENANCE
Periodic maintenance is vital to safe and efficient operation of your generator.
Check the table below for periodic maintenance intervals.
IT IS ALSO NECESSARY FOR THE USER OF THIS GENERATOR TO
CONDUCT THE MAINTENANCE AND ADJUSTMENTS ON THE EMISSIONRELATED PARTS LISTED BELOW TO KEEP THE EMISSION CONTROL
SYSTEM EFFECTIVE.
The emission control system consists of the following parts :
(1) Carburetor and internal parts
(5) Spark plug
(2) Cold start enrichment system,
if applicable
(6) Magneto or electronic ignition
system
(3) Intake manifold, if applicable
(7) Spark advance/retard
system, if applicable
(4) Air cleaner elements
(8) Exhaust manifold, if
applicable
(9) Hoses, belts, connectors, and
assemblies
The maintenance schedule indicated in the table is based on the normal generator operation. Should the
generator be operated in extremely dusty condition or in heavier loading condition, the maintenance intervals
must be shortened depending on the contamination of oil, clogging of filter elements, wear of parts, and so on.
12
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ13
Periodic Maintenance Schedule table
Maintenance Items
CLEAN GENERATOR AND CHECK
BOLT AND NUTS
CHECK AND REFILL ENGINE OIL
Every
8 hours
(Daily)
Every
20 hours
Every
50 hours
(Weekly)
Every
200 hours
(Monthly)
Every
500
hours
Every
1000
hours
● (Daily)
●
(Refill daily up to upper level)
● (Initial)
CHANGE ENGINE OIL (*Note1)
●
(Every 100 hours)
CLEAN SPARK PLUG
●
CLEAN AIR CLEANER
●
GB
REPLACE AIR CLEANER ELEMENT
●
GB
US
CLEAN FUEL FILTER
●
CLEAN AND ADJUST SPARK PLUG
AND ELECTRODES
●
GB
GB
GB
●
REPLACE SPARK PLUG
GB
● (Every 100 hours)
SPARK ARRESTER
GB
GB
REMOVE CARBON FROM
CYLINDER HEAD (*Note 2)
●
CHECK AND ADJUST VALVE
CLEARANCE (*Note 2)
●
GB
CLEAN AND ADJUST
CARBURETOR (*Note 2)
●
GB
CLEAN AND REPLACE
CARBON BRUSHES
●
GB
GB
REPLACE FUEL LINES
GB
●
GB
●
GB
(Yearly)
OVERHAUL ENGINE (*Note 2)
AC REXEPTACLES
● (Daily)
PILOT LAMP
● (Daily)
ROTOR
●
STATOR
●
REPLACE ENGINE MOUNT
●
*Note: 1. Initial oil change should be performed after first twenty (20) hours of operation. Thereafter
change oil every hundred (100) hours.
Before changing oil, check for a suitable way to dispose of old oil.
Do not pour it down into sewage drains, onto garden soil or into open streams. Your local zoning
or environmental regulations will give you more detailed instructions on proper disposal.
*Note: 2. As to the procedures for these items, please refer to the SERVICE MANUAL or consult your
nearest Makita service dealer.
13
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ14
8. "HOW-TO" MAINTENANCE
(See Fig. 5)
q)
1. ENGINE OIL CHANGE (See Fig. 5-q
■
Change engine oil every 50 hours.
(For new engine, change oil after 20 hours.)
(a) Drain oil by removing the drain plug and the oil
filler cap while the engine is warm.
q OIL DRAIN PLUG
(b) Reinstall the drain plug and fill the engine with
oil until it reaches the upper level on the oil filler cap.
■
US
GB
GB
GB
GB
GB
GB
GB
GB
GB
Use fresh and high quality lubricating oil to the
specified level as directed on page 5.
If contaminated or deteriorated oil is used or the
quantity of the engine oil is not sufficient, the
engine damage will result and its life will be
greatly shortened.
2. SERVICING THE AIR CLEANER
w)
(See Fig. 5-w
Maintaining an air cleaner in proper condition is
very important.
Dirt induced through improperly installed,
improperly serviced or inadequate elements
damages and wears out engines. Keep the
element always clean.
GB (a) Unhook the cover and remove the cleaner
GB
element.
q w ELEMENT (Urethane form)
GB (b) Urethane form : Wash the element with fresh
water. Squeeze out the water then dry the
GB
GB
element. (Do not twist.)
GB
3. CLEANING AND ADJUSTING
e,r
r)
SPARK PLUG (See Fig. 5-e
(a) If the plug is contaminated with carbon, remove
it using a plug cleaner or wire brush.
(b) Adjust the electrode gap to 0.6 to 0.7 mm (0.024
to 0.028 in.).
q SPARK PLUG
w PLUG WRENCH
e SPARK PLUG CAP
Model
Spark plug
G2800L
G3200L
G4300L
14
NGK BR-6HS
(CHAMPION RL86C)
4. CLEANING FUEL STRAINER
t)
(See Fig. 5-t
Dirt and water in the fuel are removed by the fuel
strainer.
q FUEL STRAINER CUP
(a) Remove the strainer cup and throw away water
and dirt.
(b) Clean the screen and strainer cup with gasoline.
(c) Tightly fasten the cup to main body, making sure
to avoid fuel leak.
5. CHECKING CARBON BRUSH
y)
(See Fig. 5-y
If the brush become excessively worn, its contact
pressure with the slip ring changes and causes a
roughened surface on the slip ring, resulting in
irregular generator performance.
Check the brush every 500 hours or if generator
performance is irregular.
If the brush is 5 mm (0.2 in.) long or less, replace it
with a new one.
q BRUSH HOLDER
w BRUSH
e 5 mm
r M5 BOLT : 1 pc.
t BRUSH COVER
(a) Remove the brush cover.
(b) Disconnect the wire connector and remove the
brush.
(c) Carefully note the brush direction and relative
position with the slip ring when installing new
brush.
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ15
9. PREPARATION FOR STORAGE (See Fig. 6)
The following procedures should be followed prior to storage of your generator for periods of 6 months or longer.
■
Drain fuel from fuel tank carefully by disconnecting the fuel line.
Gasoline left in the fuel tank will eventually deteriorate making engine-starting difficult.
■
Remove the drain screw of the carburetor.(See Fig. 6-q)
q DRAIN SCREW
■
Change engine oil.
■
Check for loose bolts and screws, tighten them if necessary.
■
Clean generator thoroughly with oiled cloth. Spray with preservative if available. NEVER USE WATER
TO CLEAN GENERATOR !
■
Pull starter handle until resistance is felt, leaving handle in that position.
■
Store generator in a well ventilated, low humidity area.
US
GB
10. TROUBLESHOOTING
GB
When generator engine fails to start after several attempts, or if no electricity is available at the output
socket, check the following chart. If your generator still fails to start or generate electricity, contact your
nearest Makita factory or authorized service center for further information or corrective procedures.
When Engine Fails to Start:
GB
GB
GB
GB
GB
Check if engine switch is in its proper position.
Turn engine switch to "
Check fuel level.
If empty, refill fuel tank making sure not to overfill.
GB
Check to make sure generator is not
connected to an appliance.
If connected, turn off the power switch on the
connected appliance and unplug.
GB
Check spark plug for loose spark plug cap.
If loose, push spark plug cap back into place.
GB
Check spark plug for contamination.
Remove spark plug and clean electrode.
GB
Check engine oil level.
If the engine oil level is low, add the oil to the
upper level line on the oil gauge.
"(CHOKE) position.
GB
GB
GB
GB
When No Electricity Is Generated at Receptacle :
Check if the breaker is not activated with the
overload lamp turned on.
Check if the DC circuit breaker is turned off.
Depress the circuit breaker into ON position,
after making sure the electric power
level is proper and the electric appliance(s)
are in the normal condition.
Check AC terminals for loose connection.
Secure connection if necessary.
Check to see if engine starting was
attempted with appliances already
connected to generator.
Turn off switch on the appliance, and
disconnect cable from receptacle. Reconnect
after generator has been started properly.
Low power.
Carbon brushes are excessively worn
15
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ16
11. SPECIFICATIONS
MODEL
G2800L
G3200L
AVR
Type
Alternator
Frequency
US
GB
G4300L
Rated voltage
Hz
60
V
120
Maximum output
kVA
2.8
3.2
4.3
Rated output
kVA
2.4
2.7
3.7
Rated power factor
1.0
GB
No fuse Breaker
GB
Over current protector
GB
Model
EX17
Type
Forced air-cooled, 4-cycle, OHC Gasoline Engine
EX21
EX27
GB
GB
Displacement
GB
Engine
GB
mL
169
212
Fuel
Automotive Unleaded Gasoline
GB
Fuel tank capacity L(U.S. gal)
10.8 (2.9)
GB
Rated continuous operation
GB
[Approx.]
GB
Starting system
GB
GB
Dimension
GB
hours
12.8 (3.9)
6.7
6.4
Recoil
Length
mm(in.)
537 (21.1)
580 (22.8)
Width
mm(in.)
432 (17.0)
477 (18.8)
High
mm(in.)
475 (18.7)
508 (20.0)
Dry weight
kg(lb)
Valve Clearance
(Intake & Exhaust)
mm(in.)
Emissions Durability Period
(California only)
16
7.5
265
43 (94.8)
48 (105.8)
55 (121.3)
0.1±0.03 (0.0039±0.0012)
Note : Adjust the valve clearance while the engine is cold.
500 hours
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ17
12.WIRING DIAGRAM
G2800L / G3200L (60Hz-120V)
Main
coil (2)
CONTROL PANEL
Brush (+)
Exciter
coil
PL
Spark plug
AC
receptacle
(120V)
Ignition coil
Blu
Pilot
lamp
Brush (-)
ENGINE
AC circuit breaker
Main
coil (1)
Field Winding
GENERATOR
US
GB
GB
R
GB
AVR
Grn/Y
Blk
GB
Blk
Stop switch
GB
Oil sensor
control unit
Earth
(ground)
terminal
GB
GB
GB
GB
Oil sensor
GB
Wiring color cord
Blk
: Black
Blk/W : Black/White
Blu
: Blue
GB
LBlu : Light blue
Brn
: Brown
Brn/W : Brown/White
Grn
: Green
Grn/W : Green/White
Org
: Orange
Gry : Gray
R
: Red
W : White
Y
: Yellow
W/Blk : White/Black
Grn/Y : Green/Yellow
Pur
: Purple
GB
GB
GB
GB
17
G2800L(US)_GU1843 2004.2.6 1:14 PM ページ18
G4300L (60Hz-120V)
Main
coil (2)
CONTROL PANEL
GB
Brush (+)
AC
receptacle
(120V)
Exciter
coil
PL
R
AVR
GB
Grn/Y
Blk
GB
Blk
Stop switch
Oil sensor
control unit
GB
GB
Earth
(ground)
terminal
GB
GB
Oil sensor
GB
GB
Wiring color cord
GB
Blk
: Black
Blk/W : Black/White
Blu
: Blue
GB
GB
GB
18
LBlu : Light blue
Brn
: Brown
Brn/W : Brown/White
Grn
: Green
Grn/W : Green/White
Org
: Orange
Gry : Gray
R
: Red
W : White
Y
: Yellow
W/Blk : White/Black
Grn/Y : Green/Yellow
Pur
: Purple
Spark plug
Pilot
lamp
Brush (-)
GB
AC
receptacle
(120V)
Ignition coil
Blu
US
GB
ENGINE
AC circuit breaker
Main
coil (1)
Field Winding
GENERATOR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement