www.norstateindustrial.com.au 1 1 North Street Rockhampton, QLD

www.norstateindustrial.com.au 1 1 North Street Rockhampton, QLD
1 North Street Rockhampton, QLD 4700
Ph: (07) 49 222 000 Fax: (07) 49 222 553
Email: [email protected]
What can we do for you?
Norstate Industrial Supplies, through our Hire partner Red-D-Arc Welderentals, can offer our clients a
full range of rental welding and positioning equipment for a variety of processes and applications.
Red-D-Arc is the largest provider of welding and welding related products in the USA with access to over
60,000 units in our fleet.
Our rental products have been engineered and built to provide extreme performance and reliability in
even the harshest environments.
We can supply you with the equipment you need - where you need it, when you need it.
In addition with equipment selection, Norstate Industrials Supplies can assist you in choosing the best
process for each welding and cutting application. We can supply and service equipment for the
following manual and automatic welding and cutting processes:
• Stick (SMAW) welding
• MIG (GMAW) welding
• Pulsed MIG (GMAW-P) welding
• Self-shielded flux-cored (FCAW-SS) welding
• Gas-shielded flux-cored (FCAW-GS) welding
• Submerged arc (SAW) welding
• TIG (GTAW) welding and pulsed TIG (GTAW-P) welding
• Air carbon arc cutting and gouging (CAC-A)
• Plasma (PAC) cutting and gouging
Please feel free to contact our sales team regarding any information or pricing you may require.
Rental Catalogue
Diesel Engine-Driven Welders................................................................................................................4-6
Stud Welders..........................................................................................................................................6
Multi-process Welders and Packs..........................................................................................................7-11
Semiautomatic/ Automatic Wire Feeders...............................................................................................11
Submerged Arc Tractor/ Automatic Girth Welder………………………………………………………………………..12
TIG Welders............................................................................................................................................13-14
Plasma Cutters………………………............................................................................................................15
Column and Boom Manipulators............................................................................................................16
Welding Positioners................................................................................................................................16
Power Distribution Boxes.......................................................................................................................18
Conventional and Self-Aligning Rotators................................................................................................19
Fit-Up-Bed Rollers..................................................................................................................................19
Kat Flexible/Straight Track Travel Carriage System...............................................................................20
Welding Oven..........................................................................................................................................20
Induction Heating Equipment..................................................................................................................21-23
Rental Catalogue
Lincoln Ranger 305D Diesel Engine-Driven Welder
Ranger 305D CC/CV Welder
CC-Stick, Down Hill Stick Welding on Pipe, CV Wire and Touch-Start TIG Processes
18.8 HP D722 Diesel Engine
Dual Digital Output Meters
The Ranger 305D is a powerful 300 amp CC/CV multi-process diesel engine-driven welder
designed especially for contractors, maintenance and repair and all other field based welding
professionals who demand the best welding arc from an engine driven welder.
This machine has been designed using Lincoln’s Chopper Technology™ giving you excellent
arc characteristics whether used in stick (conventional or pipe), TIG, MIG or arc gouging
modes of operation. Rugged and dependable, the 305D is built within a totally enclosed case,
which provides maximum protection to its 45-litre fuel tank top-of-the-line water-cooled
Kubota diesel engine. This portable powerhouse delivers 8000 continuous (8.500 peak)
watts of 120, 240, 415 volt AC generator power, enough power to run lights, tools, pump and
weld all at the same me. The 305D meets all the new stringent European regulations
including 50 Hz, installation and 240, 415 volt power requirements.
• Lower noise than partially all enclosed and unenclosed welders of comparable size
• Longer engine and greater fuel economy with automatic engine idler
• Single, full-range output control dial
• Flip down control panel door keeps less frequently used dials out of the way
Weight: 341 kg
Dimensions (mm) H x W x L: 909 x 546 x 1327
Current Range: CC/CV 20 - 300 A
Duty Cycle: 305A/29V/@100%
Operating Speed (rpm): Full Load: 3000 High Idle: 3100 Low Idle: 2200
Noise: 98 DBLWA, 74 DBLWA at 7 m
Lincoln Vantage 400 Diesel Engine-Driven Welder
Stick, DC TIG, MIG, Flux-Cored, Gouging
The Vantage 400 is one of the most compact 400amp engine-driven welder/generators
available to the construction, pipe and rental fleet markets today. It’s also one of the quietest,
with a smooth-running, 4-cylinder Perkins diesel engine. Use this multi-process welder for
arc gouging with up to 8mm carbons, stick weld with up to 6mm electrodes and CV wire
weld with up to 2.4mm wire. Superior performance delivered by Lincoln Chopper Technology
ensures optimum productivity. You’ll also appreciate the VRD (Voltage Reduction Device),
which reduces OCV (Open circuit voltage) in the CC-stick weld mode for added safety.
This model efficiently generates 13,200 watts of AC generator power for your lights, grinders
and power tools. Housed in a rugged, low-maintenance stainless steel enclosure, it’s loaded
with many innovative service features. It’s a power package that’s excellent value!
Weight: 560kg
Dimensions H x W x D: 913 x 642 x 1524
Mains Voltage: 240V / 415V
Output Range: 30 – 400A DC, 40 -300A Pipe, 20-250A DC TIG, 14-36 CV
Rated Output: 350/34V @ 100%, 400A/30V @ 60%
Rental Catalogue
Lincoln Vantage 575 Diesel Engine-Driven
MMAW, TIG, MIG, FCAW-SS, Submerged Arc Gouging Processes
Standard Touch-Start® DC TIG welding
For heavy duty welding and arc gouging, the Vantage 575 stands up to the toughest job
applications. The Vantage 575 features the advantages of Lincoln Chopper Technology, an
innovation to control the DC welding performance. Simplified front panel layout and
presentable digital welding meters which make setup quick and easy. The Vantage 575 is
also a powerful generator producing 20 kVA of auxiliary power, 240 and 415 volts. Enough
power to run 2 or 3 additional inverter power sources for multiple operator performance.
• CC-Stick mode is optimised for general purpose and E7018 low hydrogen electrode
• Arc control adjustment for a soft, buttery arc or a more forceful, digging arc
• Touch-Start™ DC TIG welding, for easy arc starting that avoids tungsten contamination
and the use of high frequency
• Digital meters
• Automated Remote Control Capability
Weight: 741 kg
Dimensions (mm) H x W x D: 1295 x 800 x 1600
AC Auxiliary Power: 20,000 watts
Output Range: 30 - 575 A CC/CV range
Duty Cycle: 450 A/38 V/100%
500 A/40 V/60%
Lincoln Vantage 580 Diesel Engine-Driven
Vantage 580 CC/CV Welder
Stick, Stick Pipe, LIFT TIG, MIG and Arc Gouging
Arc Gouging up to 10 mm
Low Noise
The Vantage 580 is one of the most compact and powerful diesel engine-driven
welders/generators in the construct on, pipe or rental fleet market today. They are also the
most quiet, with a smooth running 4-cylinder Perkins® water cooled diesel engine. The
Vantage 580 includes VRD (Voltage Reduction Device), which reduces OCV (open circuit
voltage) in the CC Stick weld mode for added safety. These models effectively generate
high auxiliary power on 3-phase or 1-phase AC to power your lights, grinders, power tools,
and Inverters.
They are housed in a rugged, low maintenance stainless steel enclosure and loaded with
many innovative service features.
• Downhill pipe welding mode - excellent for cellulosic electrodes
• Built-in “hot start” for easier starts and restrikes
• Reliable engine 4 cylinder, water cooled, 1500 rpm Perkins diesel engine
• Stainless steel enclosure delivers added protection and durability
• Plenty of AC 50 Hz generator power: 3-phase 400 volt/1-phase 230 volt
Weight: 586Kg
Dimensions (mm) H x W x L: 913 x 642 x 1524
Rated Output: 500 A/40/ @ 100%, 525A/39V/@60%
Output Range: 30 - 580A
Aux power: 2x 240V/15A, 1x 415V/32A
Operation Speeds (rpm): Full Load: 1500 Low Idle: 1200
Noise (sound level): 71 dBA at 7 m
Rental Catalogue
Lincoln Air Vantage 500 Diesel Engine-Driven
Stick, TIG, MIG, Flux-Cored, Submerged Arc Gouging Processes
Pumps out plenty of air for arc gouging with up to 3/8" carbons, plasma cutting or almost
any air tool. Powerful 500 amps at 100% duty cycle is enough for almost any stick, TIG,
MIG or flux-cored welding project.
12,000 watts of single-phase is standard. Stainless steel roof and side panels provide
added durability and corrosion-resistance.
• Stainless Steel Enclosure
• VRD™ Voltage Reduction Device™
• Plenty of AC generator power
• Standard Touch-Start® DC TIG welding
• Downhill pipe mode with arc force control
• Built-in “hot” start for easier starts and restrikes
Weight: 785 kg
Dimensions (mm) H x W x L: 1260 x831 x 1603
Output Range: Continuous Control 30-575 Amps CC/CV Range, 15-250 Amps TIG Range
Rated Output: 500A/40V/@100, 550A/36V/@60. 575A/35V/@50%
Aux Power: 12kW 2x 240V/15A
Nelson Stud Inverter / Welder
Stud welding is where a metal stud is end welded to another metal object instantaneously,
utilising an arc to melt the areas being joined. The two most popular methods are Capacitor
Discharge (CD) and Drawn Arc Stud Welding.
Construction Sites, Mine Sites, Decking installations, wear plates, propping & formwork
good or bad construction sites are a world unto themselves. Lack of space, tight deadlines,
multiple trades in close proximity, rigorous safety and QA documentation, and sometimes
questionable drawing details, all come together to create what can be a challenging
We would be happy to discuss your project with you and recommend the appropriate
equipment and studs.
The welding process and operation is not complicated, an unskilled handy person can
easily perform the task successfully.
Weight: 43.5kg
Dimension H x D x W: 330mm x 250mm x 520mm
Input Power: 3PH 400-480V, 50/60Hz @ 15A
Output Current: 50-1500A (step adjustable)
Welding Rate:
Drawn arc 16mm dia. : 7per minute
19mm dia. : 3per minute
Short cycle:12mm dia. : 30per minute
Full-size diameter of welding:
Drawn arc 3mm-19mm
Short cycle 4mm-12mm
Shield cycle 3mm-12mm
Rental Catalogue
Lincoln Flextec 450 Multi-Process Welder
Stick, DC TIG. MIG, Flux-cored, Arc Gouging
This multi-process welder delivers up to 500 amps of welding power for a variety of
applications, including construction and fabrication. It features an IP23 rating for outdoor
operation and storage, and the latest inverter technology will save you real dollars on the
utility costs associated with your welding operations.
Flexible Multi-Process Capability – Including stick, Touch Start TIG (DC), MIG, flux-cored
welding and carbon arc gouging with up to a 3/8 in. (9.5 mm) carbon.
The Future is Now – You no longer have to pay a price premium to gain the advantages of
inverter technology over conventional welders.
- Faster arc response means smoother arc action and more consistent bead appearance.
- Low power consumption results in daily operational cost savings.
- Enhanced portability – typically 50% less weight, size and footprint.
- VRD (Voltage Reduction Device) Reduces OCV (open circuit voltage) when not welding
for added safety
Weight: 56kg
Dimension H x W x D: 477mm x 356mm x 673mm
Input Power: 380/460/575/3/50/60
Rated Output: 400A/36V/100%, 450A/38V/60%
Input Current: 29/21/17, 37/27/22
Output Range 5-500A DC
Lincoln Invertec V350-PRO Multiprocess Welder
MIG, Stick, Flux Cored Processes
Presentable Digital Meters
Compact and Lightweight
The V350-PRO is the most powerful inverter power source in its class.
Extremely lightweight, the smart design allows it to handle any constant current stick
(SMAW), TIG (GTAW), carbon arc gouging constant voltage MIG (GMAW) and flux-cored
welding applications. Advanced inverter technology gives a very portable power source that
can be carried to just about any DC welding job needing between 5 and 425 amps.
The V350-PRO can endure the rigors of virtually any work environment.
The V350-PRO has full remote capabilities, 14-pin MS-type connectors, and can accept a
variety of Lincoln wire feeders. An intelligent machine with advanced plug-and-play
technology allows you to simply plug your wire feeder into your power source.
- Bright, large digital amp and volt meters for easy procedure monitoring
- Special Fan-As-Needed (FAN) cooling for less energy use and less dust brought into the
- Superior arc control for soft or crisp arc using different types of wire
- Electronic and thermostatic protection from over-current and over-temperature with
thermal indicator light
- VRD (Voltage Reduction Device) Reduces OCV (open circuit voltage) when not welding
for added safety
Inverter Banks (6x V350-Pro’s) are also available and are perfect for site
projects with limited space such as high-rise construction.
Weight: 38 kg
Dimensions (mm) H x W x D: 400 x 320 x 700
Input Voltage: 48 A, 28 A, 26 A
Standard Voltage: 415-440 V
Output Current Range: 5 - 425 A
Input Power: 20kVA
Rental Catalogue
DC600 Power Source/ Multi-Process Welder
DC600 Multi-Process Welder
Stick, TIG, MIG, Flux-Cored, Submerged Arc and Gouging Processes
Separate Output Studs for Selecting High or Low Inductance
CC Arc Force Control Knob with Built-In “Hot Start”
The DC600 is a 650 amp, 100% duty cycle CV/CC multi process welder.
The DC600 power source is ideal for construction and shop fabrication because of its
excellent arc performance and wide variety of energy saving features. For added energy and
cost savings, this machine has a high overall efficiency of 84%. Internal components are kept
cool without wasting energy with Lincoln’s Fan-As-Needed (FAN) that shuts off automatically
when the system is cooled.
• Full range calibrated output voltage and current control for easy operation
• Two output studs for selecting high or low inductance
• FAN - solid state thermally controlled cooling fan operates only when
required - minimizing power consumption, operating noise and dust intake
Weight: 327 kg
Dimensions (mm) H x W x D: 700 x 564 x 965
Standard Voltage: V 3-phase/415V
Input Power: 122/70 A
Output and Voltage Range: 50 - 815 A, 13 - 44 V
Rated Output: 650 A/44 V/100%
815 A/44 V/60%
O.C.V: 45 CV mode, 68 CC mode
DC1000 Power Source/Welder
Extreme-Duty™ CC/CV DC Welder
MIG, Flux-Cored, Submerged Arc, and Air Carbon Arc Gouging
Standard Ammeter and Voltmeter
Rugged Tubular Pak-Lok-Frame
The DC1000 is designed for semiautomatic and automatic welding. It produces outstanding
arc characteristics on both constant voltage and constant current processes.
This provides great welding versatility in a single power source. The DC1000 has the
capability of air carbon arc gouging up to 16 millimetre diameter carbon sticks. It produces
outstanding welding performance with a single range full output control potentiometer.
The precise output of the DC1000 enhances productivity and quality control.
• Extreme-Duty™ stainless steel construction for operation in harsh environments
• Windings and rectifiers protect against moisture and corrosive environments
• Ammeter and voltmeter for viewing weld parameters
• Three position mode switch (CV Submerged Arc, CV Innershield, CC Submerged
Arc/Gouging) for optimal arc characteristics
• 500 amp output stud provides enhanced lower current arc characteristics for stick welding
and short arc solid wire and gas welding (machine codes above 9500)
Weight: 372 kg
Dimensions (mm) H x W x L: 781 x 572 x 991
Rated Output: 1000 A, 44 V at 100% duty cycle
Output Range: 16 - 46 A 150 -1300 A
75 V maximum O.C.V.
Input: 230/460/575 A, 60 Hz, 3-phase
Rental Catalogue
Invertec STT II, LN742/LF33 MIG Packages
Invertec STT II Waveform Control Welder
The revolutionary STT process permits open gap root pass welding in pipe with greater ease
of operation, better back beads and edge fusion with less spatter and smoke than other
available processes. STT II can be used with a variety of welding consumables including mild
steel, stainless steel, high nickel alloys and silicon bronze. When using CO2 on mild and
most alloy steels, the STT II is designed for challenging semi-automatic and automatic
applications where spatter, smoke, heat input and penetration control is critical.
• Consistent X-ray quality welds
• Low heat input
• Digital meters for accurate procedure setting
Weight: 53 kg
Dimensions (in) H x W x D: 23.2 x 13.2 x 24.4
Dimensions (mm) H x W x D: 589 x 336 x 620
Rated Output Current: 225 A/29 V/60%
200 A/28 V/100%
Output Range: 0 - 450 A
LN742 Semiautomatic Wire Feeder
Weight: 10.8 kg
Dimensions (mm) H x W x D: 277 x 248 x 244
Input: 42 VAC 50/60 Hz 4 A
LF33 Semiautomatic Wire Feeder
Weight: 17 kg
Dimensions (mm) H x W x D: 440 x 275 x 636
Input: 34 - 44 VAC
FastMIg KM 400/MF 33 MIG Package
Kemppi FastMig™ Basic KM 400 Power Source, MF 33 Wire Feeder
MIG/MAG Welding Processes
Wire Feed Unit
The Kemppi FastMig™ Basic is designed for the basic MIG/MAG welding needs of heavy
and medium heavy industry. FastMig™ Basic’s effective and efficient 400 amp power source
is light, modern and compactly built. They are 70% lighter and consume 10% less energy
than switch-operated power sources with a comparable output. The MF 33 wire feed units
are designed for demanding welding conditions. The double skinned plastic casing is
durable, elegant and recyclable and is fitted with a sturdy 4 x 4 feed roll device to guarantee
steady, uninterrupted wire feeding.
• Increased productivity and quality - stepless voltage and wire feed control
• Easy-to-handle - 70% lighter than equivalent switch controlled devices
• Medium and heavy metal fabrication workshops
• Steel structure workshops
• Shipbuilding and off shore
Weight of KM 400 Power Source: 35kg
Dimensions of KM 400 Power Source (mm) H x W x L: 430 x 230 x 590
Welding Range: 20A/12V-400A/36V MIG, MMA 10A/20V-400A/36V
Weight of MF 33 Wire Feeder: 13.6 kg
Dimensions of MF 33 Wire Feeder (mm) H x W x L: 510 x 200 x 310
Mains Voltage: 3 - 50/60 Hz 400 V - 15% + 20%
Welding Range: 10 V, 37 V
Open Circuit Voltage: 66 V
Rental Catalogue
Lincoln Power Wave S350 Multi-Process Welder / Dual
Portable, Powerful, Multi-Process.
The multi-process Power Wave® S350 is packed with Lincoln Electric performance
technology on both the input and output side. It provides an extremely fast arc response,
includes over 65 standard welding waveforms for optimized performance on almost any
application and efficiently converts input power to reduce operational costs – all in a
compact, rugged case.
Top Features
PowerConnect™ Technology (Patent-Pending) Tribrid Power Module - Exceptional welding
performance with high power factor and efficiency.
CheckPoint™ – A cloud-based data collection tool allows customers to view and analyse
welding data on almost any device – desktop, laptop, iPhone® or iPad®, Blackberry® and
Optional 115V (10A) AC Duplex Auxiliary Power Receptacle – Features patentpending
Surge Blocker™ Technology to ensure simultaneous welding performance is not
compromised by high starting current devices such as grinders .
Weight: 39kg
Output Range 5-350A DC
Dimensions H X W X D: 20.40 in x 14 in x 24.80 in (518 mm x 356 mm x 630 mm)
Miller PipeWorx Multi-Process Welder / Dual Feeder System
Simplified and optimized specifically for pipe welding, the PipeWorx System delivers key
benefits for pipe fabrication shops.
Exclusive Benefits of the PipeWorx System:
One Touch Welding
Set up a new weld process with a touch of a button. Increased quality and productivity with
more arc-on time by no need to manually switch polarity or cables between processes and
fewer errors caused by incorrect settings.
True Multiprocess Machine
Improved productivity and stable arc performance from one multiprocess machine. Includes
conventional Stick, TIG, FCAW and MIG welding processes optimized for pipe welding
operations. Advanced RMD® and Pro-Pulse technologies reduce number of required weld
passes, reduce rejects and allows stainless without backing gas.
Single System Design
One machine designed to perform all of your pipe welding needs—no additional capital
investment purchases for multiple machines. One machine footprint also maximizes weld cell
Process Piping
HVAC and Water Pipe
Input Power: 3-Phase Power
Rated Output: CV Mode: 400A @ 44VDC, 100% Duty cycle, CC Mode: 350A @ 34VDC, 100% Duty
Output Power Range: CV Mode: 10-44V, CC Mode: Stick 40-400A;DC TIG 10-350A
Rental Catalogue
Lincoln Power Wave 455M Multi-Process Welder / Dual Feeder
Multi-Process Waveform Control Pulse and STT Package
For welding thicker materials in robotics, hard automation and semiautomatic applications
and for other applications where heat input control, minimal distortion and reduced spatter
are essential, opt for the Power Wave455M This model features Waveform Control
Technology for both STT® mode and superior arc performance on a variety of materials,
including steel, stainless, aluminium and nickel alloys, and custom control of the arc for
each wire type and size for consistent welds time after time. The PF10M Dual is a unique
dual-head wire feeder which allows you to use two different types of wires individually for
different welding applications (STT® and Pulse as an example).
Weight: 162kg
Dimension: H x W x D: 663 x 505 x 835
Input Power: Power Wave 455 – 380/415V
Output Range: 5-500A
Lincoln LN25-Pro Wire Feeder
LN25 ProExtreme CE Portable Industrial Wire Feeder MIG, Pulsed, Cored Processes,
Digital Meters Includes Gas Solenoid, Flow Meters
The LN25 ProExtreme CE is ideal for field construction, fabrication, and shipyard jobs.
The MAXTRAC® wire drive enhances performance, while the replacement case - and
many other upgrade options can be installed in less than 5 minutes - aid in serviceability.
Includes a gas solenoid and flow meter to run both flux-cored and MIG wires.
Additional torque gearing for reliable feeding of large diameter flux-cored wires.
• 2-Step/trigger interlock provides comfort for long welds
• Digital wire-feed-speed/amperage display
• Digital voltage display
• Non-linear wire feed speed gives single range control, yet maintains sensitivity with low
feed speed
• Lightweight, impact and flame resistant polycarbonate case design keeps the internal
components protected
• Reel locking mechanism eliminates spindle cross threading
Weight: 17 kg
Dimensions (mm) H x W x D: 376 x 221 x 559
Input Voltage and Current: Across the Arc 15 - 110 VDC, 4 A input
Input Voltage and Current: Control Cable 24 - 42 VACX, 4 A input
Rated Output at 40°C (104°F): 450 A at 60% duty cycle, 325 A at 100% duty cycle
Wire Feed Speed Range: 50 - 700 ipm (1.3 - 17.7 m/min)
GMAW Wire Size Range: .023 - 1/16" (0.6 - 1.6 mm)
FCAW Wire Size Range: .030 - 5/64" (0.8 - 2.0 mm)
Rental Catalogue
LT-7 Submerged Arc Tractor
Submerged Arc DC Wire Feeder (Track Model)
Automatic Wire Feeder
Reel Holds 60 lb Solid Wire Coils
The LT-7 Tractor is a self-propelled mechanized wire feeder, designed for the submerged
arc process with track system capabilities. It is self-guiding and easy to operate. It is
designed to be used with a variety of Lincoln DC constant voltage and constant current
power sources.
The rugged, lightweight unit permits quick movement to the next joint. Its compact size fits
through small openings and confined spaces.
• Calibrated tractor drive adjusts travel speed from 6 inches to 70 inches per minute (0.12
to 1.8 metres/minute)
• Control box is conveniently located on the tractor (can be mounted either left or right),
eliminating the need to return to the power source for routine procedure changes
• Exceptional tracking control and self-steering in most applications leave the operator free
for quality control, joint cleaning and flux handling
• Welds butt, horizontal fillet and lap joints to the left or right side of the tractor frame
• Close mechanical alignment between wire and joint maximizing weld quality
• Ship and barge building
• Storage tank erection
Weight: 59 kg
Dimensions (mm) H x W x D: 698 x 838 x 356
Input: 115 VAC 50/60 Hz
Wire Speed Range IPM (m/min): 100 - 400 (2.5 - 10.2)
Solid Wire Size Range in (mm): 3/32 - 3/16 (2.4 - 4.8)
Rated Output Current/Duty Cycle: 600 A/100%, 1100 A/100% (with water cooling)
(AGW) Automatic Girth Welder
AGW-II Automatic Girth Welder
Automatic Wire Feeder
Loading Safety Wheels
Includes 200' of Control Cable Assembly
The Ransome Automatic Girth Welder (AGW) (or 3 O’clock Welder) performs x-ray quality
horizontal welds up to 20 times faster than standard manual techniques.
Operating at speeds from 4 inches to 105 inches per minute, the AGW can handle plates as
thick as 2 inches and tank diameters from the largest to as small as 30 feet. The adjustable
A-frame telescopes manually to handle 6 feet to 10 feet high steel plates. Ergonomically
designed for efficiency, convenience, and accessibility.
The AGW Automatic Girth Welder is available as a single-sided or dual-sided mobile
welding station completely equipped with welding heads, all controls, flux support belts and
flux recovery units and welding power source. The AGW straddles the tank shell plates,
riding on serrated steel drive wheels that can be adjusted for tank diameter. The AGW
operator platform is a sturdy and solid workstation with guardrails and all-weather curtains for
operator safety and comfort.
• Effectively cuts welding time up to 40%
• Adjustable frame for plated 6 feet to 10 feet tall (1.8 metres - 3 metres)
• Unlimited tank diameters down to 15 feet in diameter
• High/low rapid travel select controls
• Single and double sided operation
Weight: 2768 kg
Dimensions (mm) H x W x D: 3150 x 2216 x 2268
Dynasty 200 DX TIG Welder
Dynasty 200 DX TIG Welder
TIG, Pulsed, Stick Processes
High-Speed DC TIG Pulse Controls
Maximum flexibility - Miller Electric combines advanced inverter technology with Auto-Line™
technology, offering the most flexible AC/DC TIG/Stick power supply in the welding industry.
The Dynasty 200 DX provides pulse on/off, pulse frequency, peak % time, background
amperage, initial amperage, initial slope time, final slope time and final amperage control.
• Advanced squarewave arc for improved weldability on aluminium and magnesium using low
power - continuous high-frequency is not needed because of the advanced squarewave arc
• AC frequency control range of 20 - 250 Hz provides control for a focused arc, resulting in
better directional control to help produce desired arc/weld bead characteristics
• Low OCV Stick is a simple design that reduces open-circuit voltage to 5 - 10 VDC when the
power source is not in use. This built-in circuit design eliminates the need for add-on voltage
Weight: 20.5 kg
Dimensions (mm) H x W x D: 343 x 191 x 546
Welding Amperage Range: 1 - 200 A
Rated Output: 3-Phase: 200 A at 18 V, 20% duty cycle
150 A at 16 V, 60% duty cycle
Single-Phase: 150 A at 16 V, 60% duty cycle
100 A at 14 V, 100% duty cycle
Maximum Open-Circuit Voltage: 80 VDC 12 - 16
Miller Maxstar 200 DX
Miller Maxstar 200DX
When the job demands greater control the DX provides pulse on/off, pulse frequency,
peak % time, background amps, initial amps, initial slope time, final slope time and final
amperage control.
DC TIG Features
Exceptionally smooth and precise arc for welding exotic materials
Lift Arc Starting provides x-ray clean welds in DC arc starting without the use of high
Stick Features:
Tailored arc control (DIG) allows the arc characteristics to be changed for specific
applications and electrodes. Smooth running 7018 or stiffer, more penetrating arc 6010.
Hot start adaptive control provides positive arc starts without sticking.
Low OCV Stick is a simple design that reduces open-circuit voltage to 5-10 VDC when
power source is not in use. This built-in circuit design eliminates the need for add-on voltage
Weight: 39 lb (16.8kg)
Dimensions (mm) H x W x D: 343 x 191 x 445
Rated Output Amps/Duty Cycle:
TIG: 3PH-175A/17V/@60, 1PH-175A/17V/@60%
Stick: 3PH-150A/26V/@60%, 1PH-150A/26V/@60%
Rated Input: 3PH-230V/10.5A/@60%, 1PH- 230V/17.4A/60%
Rental Catalogue
Lincoln V270-TP TIG Welder
CC DC Stick Inverter Welder
Stick, TIG Welding Processes
Digital Amperage Display Maximum Output 270 Amps
The V270-TP Stick and Lift TIG welder has been designed and manufactured using the
latest digital inverter technology, combining both a rugged industrial construction with
excellent arc characteristics. The lightweight but solid build of this machine makes it suitable
for operation on site in conjunction with a generator or within a workshop environment,
providing maximum Flexibility.
• Excellent arc characteristics
• Maximum output of 270 amps allows the use of electrodes up to 5.0 millimetres
• Excellent stick rutile, basic and cellulosic welding performance
• Adjustable Arc Force and Hot Start standard
• Full featured and user-friendly control panel
• Line voltage compensation enables use on remote power from an engine driven generator
• Features Lift TIG with no tungsten contamination
• Digital display allows precise setting of welding current
• Meets IEC974-1, ROHS and CE standards for safety and reliability
Weight: 30 lb (13.5 kg)
Dimensions (mm) H x W x D: 385 x 215 x 480
Rated CC DC Output: 270 A at 35% duty cycle
Input DC Volts: 230/400 V
Dynasty 350 TIG Welder
Dynasty 350 TIG Welder
TIG, Pulsed, Stick Processes
High-Speed DC TIG Pulse Controls
The Dynasty 350 Series is a powerful, compact AC/DC inverter that delivers superior arc
performance with total AC arc shaping capabilities
• Fan-On-Demand (FAN) cooling system only operates when needed
• Programmable start parameters allow independent starting conditions based on process
and memory selections (amperage, time and polarity)
• 120 volt auxiliary power receptacle for cooling system
• Extended balance control range (30 - 90% EN) allows precise cleaning control and
prolonged tungsten life
• Precision metal fabrication
• Heavy fabrication
• Pipe and tube fabrication
• Aerospace
Weight: 61 kg
Dimensions (in) H x W x D: 24.75 x 13.75 x 22
Dimensions (mm) H x W x D: 629 x 349 x 559
Welding Amperage Range: 5 - 350 A
Rated Output: 3-Phase: 300 A at 32 V, 60% duty cycle
Maximum Open-Circuit Voltage: 75 VDC 10 - 15 VDC
Rental Catalogue
Powermax 30 Plasma Cutter
For those who cut anything but corners.
From spark to finish, no other brand can cut it against a Powermax air plasma system.
That's because we continuously devote more resources to plasma cutting engineering than
any other company. It's how we've remained on the cutting edge of technology for 45 years.
You see, we know you're not just buying a tool, you're making an investment in yourself.
The new Powermax 30 delivers high-performance in a small portable package. With its twoin-one design, the system provides high-power capability for thick metal cutting, plus
FineCut consumables for detailed, thin metal cutting.
High portability, simple controls and a stable plasma arc make Powermax systems easy to
operate for beginners and experts.
State-of-the-art consumable technology delivers faster speeds and better cut quality to help
you do more in less time.
Long consumable life, combined with fast cut speeds, lower your costs of cutting and
With the largest variety of plasma torches on the market, and amperages ranging from 30 to
125 amps, you can tackle any metal cutting or gouging job. And cut speeds that are faster
than oxyfuel on metals up to 1-1/2" ensure you'll get the job done on time.
Weight: 9.5kg
Dimensions H x D x W: 305mm x 168mm x 356mm
Rated Output: 15-30A
Powermax 1650 Plasma Cutter
Hand Cutting, Gouging, Mechanised cutting, X-Y tables, track systems, pipe systems,
Robotic systems
Advanced digitally controlled inverter design delivers continuously adjustable, constant
current output from 30 to 100 amps, permitting high-quality cuts over a wide range of metal
An active electronic pilot controller for cutting expanded metal or grated
Gouging setting allows for improved arc transfer, easier operation and faster metal removal.
CNC / robotic machine interface is standard on all units, allowing automated control and
rapid changeover to mechanised operation
Patented nozzle shield lets you drag the torch on the work piece at full output without
damaging consumables and protects the nozzle from molten metal spray and double arcing.
Postflow cooling reduces torch stress.
Dimensions H x W x D: 655mm x 427mm x 671mm
Rated Output: 30-100A ~ 160VDC
Work Cable length: 4.5m
Gas Supply: Clean, dry, oil-free air or nitrogen
Recommended flow rate: 90psi
Rental Catalogue
Welding Positioners
Welding positioners are designed to manipulate a non-cylindrical work-piece so as to
present the weld instantly in the down-hand position to the operator or welding head.
The work-piece itself is mounted on the positioner table which can then be both rotated and
tilted to manipulate the work-piece into the required position.
The use of a welding positioner enables the operator to manipulate their own work-piece unassisted, provides accurate and consistent rotation speeds for high-quality welds and
optimum deposition rates, saves time wasted by cranes, reduces accident hazards, speeds
up work, and increases output through greater efficiency leading to a reduction in welding
RP500K 0.5 t
500 kg
RP1T-TS 1 t
1,000 kg
RP1T 1 t
RP3T 3 t
RP3T-TS 3 t
RP5T 5 t
RP5T-TS 5 t
RP10T 10 t
RP35T 35 t
WHP-2,5-135-400 V-A
WHP-5-135-400 V-A
WHP-10-135-400 V-A
WHHP-10-400 V-A
WHP-30-135-400 V-A
WHHP-30-400 V-A
WHP-50-135-400 V-A
1,000 kg
3,000 kg
3,000 kg
5,000 kg
5,000 kg
10,000 kg
35,000 kg
0,25 t (250 kg)
0,5 t (500 kg)
1 t (1,000 kg)
1 t (1,000 kg)
3 t (3,000 kg)
3t (3,000 kg)
5 t (5,000 kg)
Column and Boom Manipulators
Column and boom manipulators are designed to work independently or in conjunction with
rotating and/or positioning equipment to locate an automatic welding head in the correct
position over the work-piece to achieve the necessary down hand weld.
They can also be used in conjunction with cutting machine installations, semi-automatic
welding installations and for supporting grinding heads.
Column and booms allow the use of fully-automated production techniques which result in
increased quality, reduced production time, and less operator fatigue.
Pipe Shop Series Heavy Duty Series
Model Capacity Model Capacity
RM1812VLS 1800 x 1200 mm VHD4545 4500 x 4500 mm
RM1815LLS 1800 x 1500 mm VHD5050 5000 x 5000 mm
RM2020VLS 2000 x 2000 mm VHD5555 5500 x 5500 mm
VHD6060 6000 x 6000 mm
Medium Series VHD6565 6500 x 6500 mm
Model Capacity VHD7070 7000 x 7000 mm
MHD3025 3000 x 2500 mm VHD7575 7500 x 7500 mm
MHD3030 3000 x 3000 mm VHD8080 8000 x 8000 mm
MHD3535 3500 x 3500 mm
MHD4040 4000 x 4000 mm
Rental Catalogue
Electric Power Generators
Prime power (kVA)
Standby power (kVA)
Frequency (Hz)
Voltages, single-phase/
three-phase (V)
Maximum sound power level (LwA)
Alternator excitation type
Insulation Class
Control Panel
Prime power engine (kw)
Number of cylinders
Electrical system (V)
Speed regulation accuracy (Steady State)
Fuel tank usable capacity (L)
Fuel consumption at 75% Load (L/hr)
Runtime at 75% load (hr)
Leroy Somer
Ingersoll Rand
+/- 2.5%
Leroy Somer
Leroy Somer
Ingersoll Rand
+/- 2.5%q
Ingersol Rand
+/- 0.25%
Leroy Somer
+/- 0.25%
Weight & Dimensions
L x W x H (mm)
2471 x 1003 x 1750 2720 x 1214 x 1763 2720 x 1214 x 1763 4049 x 1425 x 2385
Dry weight (kg)
Wet weight (kg)
Standard Features: double-wall fuel tank, bunding capacity min. 110% fluid, forklift pockets, remote start, two stage heavy duty air filter,
earth rod & cable, central lifting point, external emergency stop button, battery isolator switch, protective guard against hot spots, single
80% step load capability, oil sump pump, 4-pole circuit breaker, rigid bus bar terminal (5 poles), voltage adjusting potentiometer, low
level coolant shutdown (on G250 and G400 only), earth leakage protection (fixed 300 mA on G40, adjustable on G80, G100, G250
and G400).
Rental Catalogue
Lifeguard 17 / Lifeguard 16 - Power Distribution Box
LG17/LG16 are temporary power reticulation systems which will reduce your establishment
costs, provides a safer environment for your staff and simplifies changes as your site
expands. The incorpated RCD’s constantly monitor current through the phase and neutral
conductors. Should a tool or a wiring fault develop, causing current leakage to earth, the
residual current device removes the power to the socket outlets. Lifeguard 17 / Lifeguard 16
is manufactured from high impact polyethylene which is resistant to corrosion and especially
suitable for use on rugged construction sites.
The LG17/LG16 system has the ability to interconnect in many ways to reticulate power
throughout multi storey and large single level construction areas. Interconnection cables are
rated at 32 amps and are of a watertight design.
Lifeguard 17
Supply input power 63A 3 phase +N +E 415VAC
RCD 2 x 4 pole 30mA 230 – 415VAC
Socket Outlets 12 x 15a Auto switched outlets, 3x 32A three phase 3P +N +E 415VAC, 1 x LG16
Take-off. 1 x 16A single phase 2P +E
Interconnection 63A 3 phase +N +E 415VAC, BS4343, CEE17, IEC309, watertight
Weight 20kg average
Lifeguard 16
Supply input power 32A 3 phase +N +E 415VAC
RCD 4 pole 30mA 230 – 415VAC
Socket Outlets 8 x 15a Auto switched outlets, 1x 32A three phase 3P +N +E 415VAC, 1 x 16A single
phase 2P + E
Interconnection 63A 3 phase +N +E 415VAC, BS4343, CEE17, IEC309, watertight
Weight 20kg average
Lifeguard 83 Power Distribution Box
LIFEGUARD 83 is the master switchboard for the distribution of power supplies used
throughout major construction projects. LG83 provides master isolation, sub circuit
protection including sub-board distribution, site hut reticulation and provision for lighting.
LG83 is fitted with RCD’s to provide protection against electrocution for staff using electrical
Supply Input Power: 225amp main isolator
RCD: 4 pole 30mA 230-415VAC, 10kA
Socket Outlets: 3 x63amp 5 pin outlets ABL own MCB to run Lifeguard 17’s, 3x 32amp 5
pin outlets ABL own MCB to run Lifeguard 16’s, 4x 15amp Auto switched outlets 2x
Connection: Hardwire chamber
Weight: 45kg
Rental Catalogue
Conventional Rotators, Self-Aligning Rotators
A set of conventional welding rotators consists of two units; a motorised drive and an idler
support unit.
Once the work-piece is supported onto rotators it can be rotated precisely into the required
position for fitting, assembly and welding of the work-piece quickly, safely and efficiently.
Rotators can be set up as fit up bed modules and can also be used to handle cylindrical
structures while they are cleaned, painted or inspected.
Model Capacity
ACR-50 2500 kg per set
ACR-100 5 t per set
ACR-200 10 t per set
ACR-400 20 t per set
PR5/7DM 5 t per set
PR10/15DDM 10 t per set
PR15/25DM 15 t per set
PR30/45DM 30 t per set
PR60/100DM 60 t per set
PR100/15DDM 100 t per set
PR120/250DM 120 t per set
PRSE150/150MYM 150 t per set
PRS200/200DM 200 t per set
PRS300/300DM 300 t per set
PRS500/500DM 500 t per set
PRS1000/1000DM 1000 t per set
Fit-Up-Bed Rollers
FUB-30 Fit-Up-Bed Rollers
Fit-up-bed rollers are specifically designed for cans-staging applications. These rollers
enable the fabricator to reduce costs by dramatically reducing the time and effort
required for aligning and jacking of cans. The FUB-30, with its unique features, is
particularly advantageous for the piping and vessel-construction industries. This system
has been designed and built to withstand harsh and rugged environments. Replaceable
polyurethane tyres are mounted onto a cast-steel drum
for durability and superior traction. Also available with optional steel rolls.
Dimensions (in) H x W x L: 37.6 x 89.8 x 230.7
Dimensions (mm) H x W x L: 955 x 2280 x 5860
Weight: 5,290 kg
Minimum Vessel Size: 78.7" (2000 mm) at 37� included angle
Maximum Vessel Size: 177.2" (4500 mm) at 32� included angle
Tyres: Polyurethane, D 20.5" (520.7 mm) x W 7" (177.8 mm)
Electrical Panel: IEC IP Code: IP55
Turning Speed: 130 to 1295 mm/min at 50 Hz
Input Power: Per customer specifications
Control Voltage: 24 VAC
Remote Control, Standard: Push-button control pendant, with 10 m control cable
Travel Car: Motorized bogie
Travel Speed: 178-1780 mm/min
Travel Motor: AC 2 HP c/w brake
Power Pack: 2 HP
Rental Catalogue
Kat Flexible Track Travel Carriage System
Kat Flexible Track Travel Carriage System
Low Voltage
Variable Speed
The Kat Carriage Auto-Weld enables a wide variety of automated welding cycles that can be
repeatedly performed along any plane. The advanced Auto-Weld control monitors, via distance
travelled, and responds to limit switches mounted on the Kat which in turn respond to
adjustable activators mounted at appropriate positions on the Kat Track.
Travel direction/speed and length of travel path are synchronized with precise weld start and
weld stop settings. By combining different control settings and limit switch activator positions,
a wide variety of welding cycles can be repeatedly performed. The Kat Auto-Weld Combination
is ideal for stitch welding and seam welding applications where repeatability and accuracy are
desired. The reliability and precision of this automated welding system reduces cost, adds
efficiency and improves quality.
This unit is designed for operation on curved surfaces as the flexible track can be positioned
to follow the contour of the work piece. The self-aligning wheel system of the carriage grips the
top and bottom of the track, enabling it to travel along any plane. The adjustable wheel
assembly keeps the carriage snug to the track, while allowing it to be easily mounted and
removed from the track at any point. The positive drive of the “KAT” is obtained from a uniquely
designed sprocket that engages with slots in the track, driven by a low voltage permanent
magnet motor and gear-head power unit assembly.
Weight: 13 kg
Vertical Load Capacity: 100 lbs (45 kg)
Speed Range: 1.5 to 51.5 IPM 3.9 to 131 cm/min
Input Supply: 230 VAC
Drive Motor: 24 VDC permanent magnet gear motor
Welding Ovens
Compressed Gas Cylinder Cage
Full range of Welding ovens for
hire Ranging 5kg to 200kg
Gas Cylinder Cages are designed for
secure on-site storage of up to twenty
compressed-gas-cylinders. The cage
is all-steel tube and plate construction
including ¾ inch number 9 expanded
metal screen sides for natural
ventilation and visual inventory and
inspection. Cylinders are held in place
by adjustable chains and the hinged
access-door can be locked with a
padlock to deter theft and
unauthorised access. The complete
unit can be moved about the
construction site via a crane hoist
connected to the top-mounted lifting
eye. There are also four hollowstructural tubes welded to the base for
maneuvering by fork-lift.
Rental Catalogue
ProHeat 35 Liquid-Cooled Weld Preheating and Stress Relieving Systems
ProHeat 35 Air-Cooled Induction System
Rental Catalogue
Induction Heating Applications
Preheating of an in-service pipeline to 100° C before welding on a sleeve
Liquid-cooled induction coils are flexible and easy to apply to a variety of geometries.
Here, a sleeve is being welded onto a pipe that has material flowing through it - an
operation known as a "hot tap". The material flowing through the pipe is taking heat away
from the joint, but here a single 35 kW unit is able to maintain the desired temperature at
the joint. Common, inexpensive materials are used to hold the coil in place. The set-up time
and cycle-time hours were reduced as a result of using the ProHeat 35 Induction System.
Post Weld Heat Treating (PWHT) of a drill pipe to 1350° F after welding
Two PWHT joints are being processed with one water-cooled induction coil. As long as the
dimensions of the two pipe joints are similar, the applied induction field will heat both
relatively the same. This also shows the proper way to terminate any unused portion of the
coil. The ends of the coil should be twisted together or tied together with tie-wraps, tape,
rope or string in order to reduce the amount of losses in the unused portion. These
common, inexpensive materials can be used to secure the excess coil ends as the coil itself
does not heat during the process.
Preheating of structural I-Beam to 300° F
Liquid-cooled induction coils are wound "pancake" style and secured to a section of
plywood to hold the desired shape. A layer of preheat insulation is placed between the
plywood and the I-Beam to prevent the overheating of the wood. The magnetic field passes
through the plywood and the insulation to induce the desired heating of the I-Beam.
Post Weld Heat Treating (PWHT) of a P91 header to 1400° F after welding
Liquid-cooled coils wrap around PWHT insulation that is applied to the header. The
insulation is a 1" thick silica needle mat which traps the heat in the header while protecting
the coil from the high temperatures. Thermocouples are attached to the weld joint to provide
temperature data back to the power source. The integrated temperature controller on the
ProHeat 35 has a standard PWHT program that will execute the controlled heating profile,
that will ramp up to the set temperature, dwell there for a set time, then cool down at a
controlled ramp rate. Custom programs can be created within the controller with multiple
steps, ramps and dwells in a single cycle.
Rental Catalogue
ProHeat 35 Components
The induction blanket is the newest innovation in pre heat technology. The flexible,
lightweight blankets come in a variety of sizes and are capable of preheat
temperatures of up to 204 degrees Celsius. The blankets easily conform to circular
and flat parts and install in a matter of seconds. Manufactured from durable hightemperature materials, flexible induction blankets withstand the tough conditions in
industrial and construction applications. Each blanket comes with securing straps and a
replaceable Kevlar sleeve which provides added protection against abrasion, cuts and
tear, extending the blanket life
Output extension cables are available in 25,50 and 75’ (7.6,15.2 and 22.8m)
lengths and provide interconnection between the power source and the induction
blanket. The insulated twist-lock connector at the power source end identifies the type
of heating device to power the source controller. This cable identification system
prevents over duty cycling of the heating blanket
The series cable adapter is used to combine two blankets in a series. Enables one
power source and one output cable to be used to create extra heating area using two
The liquid-cooled heating cable couples the power to the part to be heated. The
silicone hose encloses a special copper conductor specifically designed for carrying
high-frequency current to maximise efficiency. The hose also carries the coolant, which
cools the strength and durability
Output extension cables are available to remote the power source up to 50 feet away
from the work. Insulated quick-connects are used to easily remove and attach the
coolant lines. The cable identification system, built into the connector at the power
source end, identifies this as a liquid-cooled system and permits full power. The cables
are flexible for ease of use.
Preheat cable covers are available to protect the heating cable from slag and molten
metal created during welding. The cable covers must be used with the ½” preheat
insulation, with temperatures up to 343 degrees Celsius
The insulation is designed to insulate the work for the process efficiency, maintain the
optimum coupling distance between the coil and the work, and protect the liquid-cooled
cable from high temperature. Preheat insulation is provided in strips of six of twelve
inches wide and ten feet long. Preheat insulation is ½” (12.7mm) thick due to the
lower temperatures of preheating. The insulation is cut to length for the application.
Postweld heat treatment insulation blankets are sized and stencilled for the pipe size
to be treated. It is sewn into the silica blanket which provides high durability, 50
thermal cycles or more can be achieved with one blanket.
1 North Street, Rockhampton, QLD 4700
Phone (07) 49 222 000 Fax (07) 49 222 553
Email: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF