DI 1 TOOL CONTROL UNIT Quick start Guide

DI 1 TOOL CONTROL  UNIT Quick  start  Guide
DI
1 TOOL
CONTROL UNIT
Quick start Guide
English
www.jbctools.com
DI/1 TOOL CONTROL UNIT
CONTAINS
+
+
DI
1 TOOL
CONTROL UNIT
INSTALLATION / I.E.CONNEXION
DESOLDERING STAND
DR-SA
CONTROL UNIT
DI-2A
DESOLDERING PUMP
MS-A
Electric intel
Connectable tools: T210, T245, PA, HT, AP, DR and DS.
Connectable modules: MS, MV and MN.
HEAT MANAGEMENT
The JBC stations intelligently manages the tool temperature:
Work status: When the tool is out of the stand, the working temperature is 350º C.
Sleep status: When the tool is on the stand, the temperature is being lowered to 220º C.
Hibernation status: During larger periods of inactivity i.e 30 minutes, the tool’s power is being cut off
and it cools down to room temperature.
WORK
HIBERNATION
220
220
SLEEP
room
temperature
time
The advantages of this heat management is the lifespan increase which ensure low cost of ownership.
2
time
WORKING
DR
Working tool model
350 C
0
Working temp
Power 10%
Status
3500C
Selected temperature
% Instant power supplied to the tool
Decreas & move down
Increase & move up
Selection
SETTINGS
Press SELECT during 2 seconds
to enter SETTINGS
Main menu
ORIGINAL PIN: 0105
Station settings
Tool settings
1 Language
English
2 Temp unit
Celsius
3 Maximum temp 4000C
4 Minimum temp
2000C
1 Fix one temp
----2 Temp levels set
OFF
3 Sleep delay
0 min
5
6
7
8
4 Sleep temp
2200C
5 Hibernation delay 30 min
6 Temp adjust
O OC
Nitrogen mode
Help text
Beep
Change PIN
Back
OFF
OFF
ON
Tool DR
Back
1
2
3
4
Reset settings
Station settings
Tool settings
Counters
5
Program version
Exit
Counters
1
2
3
4
Plugged hours
Working hours
Sleep hours
Hibernation hours
5 No tool hours
6 Sleep cycles
7 Desold cycles
Back
0
0
0
0
0
0
0
Tool DR
3
THECNICAL SPECIFICATIONS
-
-
-
-
-
-
-
Temperature selection from 90 to 450°C (±5%).
Power: 75W.
Safety transformer, mains separator and double isolation, with integrated temperature protection fuse.
DI-2A 230V control unit. Input: 230V 50Hz. Output: 24V.
DI-1A 120V control unit. Input: 100V 60Hz. Output: 24V.
Total weight of unit: 2 Kg.
Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing
“skin effect”.
- RoHS compliant.
- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.
This product should be
thrown in the garbage.
ENGLISH / WARRANTY
The JBC 2 years warranty, guarantees this equipment against all
manufacturing defects, covering the replacement of defective parts
and all necessary labour.
Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned,
postage paid, to the dealer where it was purchased enclosing this,
fully filled in, sheet.
MORE INFORMATION
www.jbctools.com
SERIAL N`
STAMP OF DEALER
DATE OF PURCHASE
JBC Industrias, S.A.
Ramón y Cajal, 3
08750 MOLINS DE REI
BARCELONA - SPAIN
Tel.: +34 93 325 32 00
Fax: +34 93 680 49 70
www.jbctools.com
[email protected]
0008528/0409
MANUFACTURED BY
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement