Datasheet | Miele DA 2250 EXT Technical data

Operating and installation instructions
Cooker hood
DA 2250, DA 2250 EXT
DA 2270, DA 2270 EXT
DA 2210
To avoid the risk of accidents
or damage to this appliance,
it is essential to read these
instructions before it is installed
and used for the first time.
en - GB
M.-Nr. 09 723 630
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To switch the fan on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To select a power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To switch the fan off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatic switch-off of the Intensive setting . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Run-on option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To switch the hob lighting on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To dim the hob lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To switch the hob lighting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fitting and replacing the charcoal filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Safety distance between hob and cooker hood. . . . . . . . . . . . . . . . . . . . . . . . 27
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Operation with Control module DSM 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2
Caring for the environment
Disposal of the packing material
Disposal of your old appliance
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
Recycling packaging reduces the use
of raw materials in the manufacturing
process and also reduces the amount
of waste in landfill sites.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This appliance is intended for use in
domestic households and in similar
working and residential environments
such as:
– Shops
– Offices and showrooms
and by residents in establishments
such as:
– Hostels and guest houses.
~ It must only be used as a domestic
appliance to extract vapours and
remove odours from cooking.
4
~ The cooker hood is not intended for
outdoor use.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.
~ This appliance is not intended for
use by people with reduced physical,
sensory or mental capabilities, or lack
of experience or knowledge, unless
they are supervised whilst using it or
have been shown how to use it
correctly by a person responsible for
their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions.
~ This appliance is not a toy! To
prevent the risk of injury do not let
children play with the appliance or its
controls.
~ Children under 8 years of age must
be kept away from the cooker hood
unless they are constantly supervised.
~ Children 8 years and older may use
the cooker hood only if they have been
shown how to use it in a safe way and
understand the hazards involved.
~ Please be aware that on cooker
hoods with halogen lighting, the lamps
will get very hot during use and remain
hot for some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.
Warning and Safety instructions
Technical safety
~ Before installation, check the cooker
hood for visible signs of damage. Do
not install and use a damaged
appliance. It could be dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
household electricity supply, otherwise
the appliance could be damaged.
Consult a qualified electrician if in any
doubt.
~ The electrical safety of this
appliance can only be guaranteed if it
is correctly earthed. It is most important
that this basic safety requirement is
observed and regularly tested and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ Installation, maintenance and
repairs may only be carried out by a
service technician authorised by the
manufacturer in strict accordance with
current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply.
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ For appliances with an external fan
motor (...EXT models) the connection of
the two units must be made using the
connection cable and the plug
connectors.
These models may only be combined
with a Miele external motor.
~ This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the guarantee.
~ Great care should be taken when
using the cooker hood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the cooker
hood and the heating appliance are in
operation simultaneously, an
underpressure in the room of 0.04 mbar
(4 pa) is the maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the cooker hood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter (GasSafe
registered in the UK) or electrician
must be sought.
If the hood is being operated in
recirculation mode, the above
restrictions do not apply.
7
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the cooker hood. To avoid the danger
of fire, do not flambé or grill over an
open flame.
When switched on, the cooker hood
could draw flames into the filter. Fat
particles drawn into the cooker hood
present a fire hazard.
~ When using the cooker hood over a
gas hob, ensure that any burners in use
are always covered by a pan. Switch
the cooking zone off when a pan is
removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The cooker hood can become
damaged when exposed to excessive
heat.
~ Always switch the cooker hood on
when using the hob, otherwise
condensation may collect in the hood,
which could cause corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
8
~ Do not use the cooker hood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ The cooker hood can get very hot
during cooking due to heat rising from
the hob.
Do not touch the housing or the grease
filters until the cooker hood has cooled
down.
~ Do not use a steam-cleaner to clean
this appliance. Steam could reach the
electrical components and cause a
short circuit.
Warning and Safety instructions
Correct installation
Accessories
~ Refer to the cooker or hob
manufacturer's instructions as to
whether a cooker hood may be
operated above the cooker/hob.
~ Only use genuine Miele original
~ The minimum safety distances
between the top of the cooker or hob
and the bottom of the cooker hood
given in the "Appliance dimensions"
section of this booklet must be
maintained, unless the hob
manufacturer states that a greater
safety distance is required.
spare parts and accessories with this
appliance. Using spare parts or
accessories from other manufacturers
will invalidate the guarantee, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
If more than one cooking appliance is
fitted beneath the cooker hood, and
they have different minimum safety
distances to the cooker hood, select
the greater distance.
~ Safety regulations prohibit the fitting
of a cooker hood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts department or from
builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
9
Guide to the appliance
10
Guide to the appliance
a Control panel
b Joystick
This is used to operate the fan settings
and the lighting.
c Hob lighting
d Charcoal filters
Special accessory for recirculation
mode
DA 2250, DA 2270: 2 filters
DA 2210: 4 filters
e Grease filters
f Fan setting indicator lamps
g Touch control for the run-on
option
i Touch control for the charcoal
filter
The indicator lamp for the charcoal filter
lights up when the charcoal filters used
in recirculation mode needs to be
replaced. For this to happen, the
operating hours counter needs to be
activated before the appliance is used
for the first time.
The touch control is used to reset the
operating hours counter every time the
charcoal filters are replaced (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
To activate the run-on option. The fan
can be set to continue running, and to
switch off automatically after either 5 or
15 minutes.
h Touch control for the grease filter
The indicator lamp for the grease filters
lights up when the grease filters need
to be cleaned.
The touch control is used to reset the
operating hours counter every time the
grease filters are cleaned (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
For information about using the
appliance, see "Operation".
11
Modes of operation
The cooker hood works with
. . . air extraction:
. . . air recirculation:
The air is drawn in and cleaned by the
grease filters and directed outside.
(requires a conversion kit and charcoal
filters: see "Technical Data")
If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
The air is drawn in and cleaned first by
the grease filters and then by the
charcoal filters (2 on the DA 2250,
DA 2270 and 4 on the DA 2210). The
cleaned air is then recirculated back
into the kitchen.
The DA 2210 has two motors and
requires two non-return flaps to be
fitted.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
Before using the cooker hood in
recirculation mode, ensure that the
charcoal filters are in place. See
"Cleaning and care".
. . . an external motor:
(EXT models only)
EXT models are designed to be
connected to an external motor located
outside the room.
The external motor is connected to
the cooker hood by means of a
control cable, and is operated by
the controls on the cooker hood.
12
Operation
Joystick
To select a power level
This is used to operate the fan settings
and the lighting.
^ Press the joystick repeatedly to the
right to select a higher power level,
and to the left to select a lower power
level.
To switch the fan on
The relevant power level indicator lamp
will light up.
Depending on the intensity of the
cooking vapours, levels "I" to "III" are
usually sufficient for normal cooking.
Intensive setting
^ Press the joystick once to the right.
For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, you may wish
to select the Intensive Setting "IV".
To switch the fan off
The fan will come on at power level lI.
The second fan power level indicator
lamp will light up.
^ Press the joystick repeatedly to the
left until the fan switches off and the
power level indicator lamps have all
gone out.
or
^ Press and hold the joystick to the left.
The power level indicator lamps will
go out.
13
Operation
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ To set this option, both the fan and
the hob lighting must be switched off.
^ Press the run-on option control for
approximately 10 seconds. The first
power level indicator lamp will light
up.
^ Press the joystick
– once to the rear or to the front. The
second indicator lamp will light up,
– then press the joystick once to left.
The third indicator lamp will light up,
– then press the joystick once to the
left or to the front.
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off for the Intensive setting is not
activated.
^ To activate automatic switch-off,
press the joystick once to the right.
The indicator lamps for power levels
"I" and "IV" will light up constantly.
^ To deactivate automatic switch-off,
press the joystick once to the left.
^ Press the control for the run-on
option to confirm the selection and
to come out of programming mode.
14
Run-on option
It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering odours in the
air, whether you are using air extraction
or recirculation mode.
The fan can be set to switch off
automatically after either 5 or 15
minutes.
^ After cooking has finished, press the
run-on option control whilst the fan is
still running.
– Press once = The fan will switch off
after 5 minutes (left-hand indicator
lamp).
– Press twice = The fan will switch off
after 15 minutes (right-hand indicator
lamp).
^ To switch off the run-on option, press
the run-on option control again. The
appliance will then not switch off
automatically.
Operation
To switch the hob lighting on
To switch the hob lighting off
The hob lighting can be switched on
and off independently of the fan.
^ Press the joystick again once to the
rear or to the front to switch it off.
Safety cut-out
Should the cooker hood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^ Pressing the joystick once to the right
will switch the fan back on again.
^ Press the joystick once to the rear or
to the front to switch it on.
To dim the hob lighting
The brightness of the lighting can be
adjusted.
^ With the lighting switched on, press
and hold the joystick to the rear or
the front.
The brightness will gradually dim until
you release the joystick.
^ Pressing and holding it again will
gradually increase the brightness
until you release it.
^ If you keep the joystick pressed in,
the light will continually change
between bright and dim.
15
Operation
Filter operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counter tells you
when the grease filters or charcoal
filters need to be cleaned or replaced.
Reading the grease filter operating
hours counter
To check the percentage of time set
already used:
^ Switch the fan on with the joystick.
Resetting the grease filter operating
hours counter
^ Press and hold the grease filter
control.
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the grease filter indicator
lamp will light up. The grease filters
must then be cleaned.
Afterwards, the grease filter operating
hours counter must be reset.
^ To do this, press and hold the grease
filter control for approximately
3 seconds while the fan is switched
on.
The indicator lamp for the grease filter
control will go out.
16
One or several of the power level
indicator lamps will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
Operation
Altering the grease filter operating
hours counter
The operating hours counter for the
grease filter is set at the factory for 30
hours. This can be lengthened or
shortened to suit the type of cooking
you do. You can choose 20, 30, 40 or
50 hours.
– Select a short time if you roast or fry
a lot.
– If you use very little fat for cooking,
select a longer time.
– If you only cook occasionally we
recommend that you still select a
short time because grease which has
built up gradually over a long period
of time will harden on the filter and
make cleaning more difficult.
^ Switch the fan off with the joystick.
^ Use the joystick to select the time
required.
Press to the left for a shorter
operating time, or to the right for a
longer time.
^ Confirm the selection by pressing the
grease filter control.
All the indicator lamps will go out.
^ Press the run-on option control and
the grease filter control at the same
time.
If you do not confirm your selection
within 4 minutes, the cooker hood will
automatically revert to the "old" data.
The indicator lamp for the grease filter
touch control and one of the power
level indicator lamps will flash.
The power level indicator lamps show
the time which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
17
Operation
Activating and altering the charcoal
filter operating hours counter
(in recirculation mode)
The charcoal filters must be fitted for
the cooker hood to be used in
recirculation mode.
On delivery, the operating hours counter
for the charcoal filter is deactivated.
For recirculation mode, the operating
hours counter needs to be set to suit
the type of cooking you do:
^ Switch the fan off with the joystick.
^ Press the run-on option control and
the charcoal filter control at the same
time.
The indicator lamp for the charcoal filter
control and one of the power level
indicator lamps will flash.
The power level indicator lamps show
the time which has been set:
1st lamp from the left = 120 hours
2nd lamp from the left = 180 hours
3rd lamp from the left = 240 hours
4th lamp from the left = unlimited
18
^ Use the joystick to select the time
required.
Press to the left for a shorter
operating time, or to the right for a
longer time.
^ Confirm the selection by pressing the
charcoal filter control.
All the indicator lamps will go out.
If you do not confirm your selection
within 4 minutes, the cooker hood will
automatically revert to the "old" data.
Operation
Resetting the charcoal filter
operating hours counter
Reading the charcoal filter operating
hours counter
To check the percentage of time set
already used:
^ Switch the fan on with the joystick.
The indicator lamp for the charcoal filter
control will light up after the cooker
hood has operated for the number of
hours set. The charcoal filters must be
replaced with new ones.
Afterwards, the charcoal filter operating
hours counter must be reset.
^ Press and hold the charcoal filter
control for about 3 seconds while the
fan is switched on.
The indicator lamp for the charcoal filter
control will go out.
^ Press and hold the charcoal filter
control.
One or several of the power level
indicator lamps will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
19
Cleaning and care
A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Dealer /
Chartered Agent, the Miele Spare Parts
Department, or via the internet on
www.miele-shop.com.
,Before any cleaning or
maintenance work is carried out,
disconnect the cooker hood from
the mains supply.
,Halogen lamps get very hot
during use and remain hot for some
time after being switched off. The
hot lamps are also susceptible to
damage from damp cleaning. Wait a
few minutes after switching off
before commencing cleaning.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
These will damage the surface
material.
Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
cooker hood.
Housing
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^ All external surfaces and controls can
be cleaned using a Miele E-Cloth, or
with warm water and a small amount
of washing-up liquid applied with a
well wrung-out soft sponge or cloth.
^ Wipe the surfaces dry using a soft
cloth.
20
To avoid a build-up of grease, the
grease filters should be cleaned
regularly (at least every 3-4 weeks), but
always clean immediately the grease
filter indicator lamp comes on.
,An oversaturated filter is a fire
hazard.
Cleaning and care
Cleaning the grease filters in the
dishwasher
^ Place the filters as upright as
possible in the lower basket, with the
short sides upright. Make sure that
the spray arm can move freely.
^ Do not wash at more than 65° C. If a
Miele dishwasher is being used,
select the Sensor wash programme.
^ To take out the grease filters, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.
To avoid damaging the filters or the
hob below, make sure you hold the
filters securely at all times when
handling them.
Cleaning the grease filters by hand
^ Use a mild dishwasher detergent.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
^ After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
^ Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid.
Do not use "neat" washing up liquid.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
21
Cleaning and care
^ When removing the filters for
cleaning, also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
When putting the grease filters back in
position, ensure that the locking clips
are facing down towards the hob.
Fitting and replacing the
charcoal filters
If the cooker hood is connected for
recirculation, charcoal filters must be
inserted in addition to the grease filters.
They are designed to absorb cooking
odours and are fitted in the canopy
above the grease filters.
DA 2250, DA 2270: 2 charcoal filters
DA 2210: 4 charcoal filters
^ If a grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
^ After replacing the grease filters,
press the grease filter control for
approximately 3 seconds to reset the
operating hours counter.
The indicator lamp will go out.
New filters can be purchased from
your Miele dealer or from the Miele
Spare Parts Department.
See back cover for contact details,
and "Technical data" for the model
number of the filter.
^ Before fitting or replacing the
charcoal filters, the grease filters
must first be taken out (see previous
section for instructions on how to do
this).
^ Unwrap the charcoal filters.
^ If the grease filters are cleaned
before the operating hours counter
has reached its maximum, the grease
filter control should be pressed for
approximately 6 seconds to reset the
counter.
^ Insert the charcoal filters into the
canopy.
^ When fitting for the first time:
Activate the charcoal filter operating
hours counter to suit your
requirements (see "Operation").
^ Replace the grease filters.
22
Cleaning and care
Always replace the charcoal filters immediately if
– the indicator lamp for the charcoal
filter control lights up,
or
– they are no longer effective in
absorbing kitchen odours.
They should, however, be replaced at
least every 6 months.
Used charcoal filters can be disposed
of with the normal household waste.
^ After fitting the new charcoal filters,
press the charcoal filter touch control
for approximately 3 seconds to reset
the operating hours counter.
The charcoal filter indicator lamp will
go out.
^ If the charcoal filters are replaced
before the operating hours counter
has reached its maximum, the
charcoal filter control should be
pressed for approximately 6 seconds
to reset the counter.
23
Cleaning and care
Changing a halogen lamp
Before any cleaning or maintenance
work is carried out, disconnect the
cooker hood from the mains supply.
^ Remove the grease filter.
^ Remove the charcoal filters if the
cooker hood is being used in
recirculation mode.
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off.
Do not touch the surface directly
when changing a lamp, as grease
particles from your fingers will
adhere to the surface and damage
it. Please follow the manufacturer's
instructions.
^ Push down the lighting unit slightly
via the opening in the safety panel.
^ The halogen lamp is now accessible
and should be unscrewed
anti-clockwise.
^ Replace it with a new halogen lamp
(specification: GU/GZ 10, 230 V,
50 W). Screw the lamp into the
socket and push it upwards.
Please follow the manufacturer's
instructions.
We recommend only using lamps of the
same specification and also made by
the same manufacturer as the ones
being replaced.
^ Replace the grease filter and, if being
used in recirculation mode, the
charcoal filters.
24
After Sales Service
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– Your Miele Dealer / Chartered Agent
or
– The Miele Service Department (see
back cover for address).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. These are
shown on the data plate which is visible
when the grease filter is removed.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However, you must activate
your cover by calling 0845 365 6640 or
registering online at www.miele.co.uk
For the U.K.: Please note that
telephone calls may be monitored
and recorded for training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
25
Appliance dimensions
*Cut-out dimensions
A depth T of at least 25 mm must be
provided at the back of the building-in
niche.
26
Appliance dimensions
Safety distance between hob and
cooker hood (S)
The following minimum safety
distance must be maintained
between the top of the cooker/hob
and the bottom of the cooker hood
unless a greater distance is
specified by the manufacturer of the
cooker or hob:
Cooking appliance
Distance
S
Electric hob
450 mm
Open Grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas hob with
a maximum total output of
12.6 kW, no burner
exceeding 4.5 kW.
650 mm
Multi-burner gas hob with
a total output of more than
12.6 kW, or a multi-burner
gas hob where one burner
exceeds 4.5 kW.
760 mm
Single gas burner with a
maximum output of 6 kW.
650 mm
Single gas burner with
output exceeding 6 kW.
760 mm
– When deciding on the safety distance
between the hob and cooker hood,
please note that a distance of 650
mm above electric cookers/hobs may
be preferable to give more working
space under the hood.
– Account should also be taken of the
height of the person who will be
using the hood most often. The
person should have sufficient space
to work comfortably at the hob, and
also be able to reach the hood
controls with ease.
– If positioned too high, extraction will
be inefficient.
See "Warning and Safety"
instructions for further information.
27
Installation
Fitting the non-return flap
(not needed for recirculation mode)
^ Place the appliance in the cut-out
from below and align it.
^ If a non-return flap is not present in
the venting system, the non-return
flap supplied must be fitted onto the
exhaust socket in the motor unit. The
flaps must open upwards.
DA 2250, DA 2270: 1 non-return flap
DA 2210: 2 non-return flaps
^ Secure the cooker hood by the frame
using 3.5 x 16 mm screws.
Building in
The cooker hood is designed for
installation in wall units, cooker hood
housing units, and above breakfast
bars or island areas.
Check prior to installation that the top of
the appliance will be accessible after
installation.
If this is not the case, install the exhaust
ducting and prepare the electrical
connection before installation.
28
^ Before using the appliance for the
first time, take the grease filters out
and remove the protective foil from
the filter frame. Then replace the
grease filters.
Installation
^ See "Connection for air extraction" for
further instructions on fitting the
ducting.
Preparation for extraction
^ DA 2210: The hood has two exhaust
connections for use with two 150 mm
diameter exhaust hoses.
A Y- adapter is supplied with the
hood. It may be used to feed the
exhaust from both connections to a
200 mm diameter common duct.
^ When using C 150 mm ducting,
secure the exhaust connection
supplied to exhaust ducting with
hose clips.
^ If using C 125 mm ducting, fit the
reducing collar into the exhaust
connection, and secure the exhaust
ducting to the reducing collar with a
hose clip. (See "Connection for air
extraction").
dai2717
^ Place the exhaust ducting on the fan
connection for the cooker hood.
29
Installation
Recirculation
A non-return flap is not used in
recirculation mode.
^ Take the on-site conditions into
account when fitting the conversion
kit.
When fitting the exhaust grille make
sure that the slats in the grille point
towards the centre of the room and
not directly towards a wall or the
ceiling.
^ Fit the charcoal filters and set the
filter operating hours counter (see
"Cleaning and Care").
If site conditions are not suitable for the
cooker hood to be used with air
extraction, the appliance must be set
up for recirculation.
For this, conversion kit DUU 151
(available from your Miele dealer or the
Miele Spare Parts Dept.) is required.
One conversion kit is required for the
DA 2250 and 2270, and two kits for the
DA 2210.
You will also require two charcoal filters
for the DA 2250 and 2270, or 4
charcoal filters for the DA 2210 (see
"Technical data").
30
Installation
Fitting the joystick
4. Then tighten the screw with a 3 mm
allen key. Continue to counterhold
the joystick with an SW 9 spanner.
Do not turn the spanner.
Joystick extension
The joystick can be extended if
required (special accessory - Miele
DBV 100).
1. Screw the spring into the holder and
tighten by hand. Whilst doing so
counterhold the joystick with an SW 9
spanner. Do not turn the spanner!
2. Then fit the middle section onto the
spring and tighten by hand whilst
continuing to counterhold the
joystick. Do not turn the spanner.
3. Then fit the lower section of the
joystick and lightly secure in position
with the screw supplied and a spring
washer. Do not tighten the screw yet.
Turn the lower section around, until
the m symbol is facing the front.
^ Assemble the spring and top section
as described above.
^ Whilst counterholding the joystick
with an SW 9 spanner (do not turn),
secure the joystick extension to the
top section.
^ Then attach the lower section of the
joystick to the extension piece as
previously described, turn the m
symbol to the front and then tighten
the screw.
31
Installation
Electrical connection
^ If the cooker hood is to be connected
to an external motor (EXT models):
Use the connection cable with 6 pole
plug to connect the cooker hood and
the external motor.
^ Connect the appliance to the mains
via a fused spur or fused socket as
appropriate.
Before connecting the appliance
read the safety notes in "Warning
and Safety instructions" and
"Electrical connection".
32
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the cooker hood at the same time as
another heating appliance which
relies on air from the same room.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
– When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the
cross-section must not be smaller
than the cross-section of the exhaust
connection.
– All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the cooker hood.
33
Connection for air extraction
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.
Condensate trap
(optional accessory)
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important:
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur. Condensate traps
are available for C 125 mm or
C 150 mm ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
Cooker hoods designed for use with an
external motor (...EXT models) have an
integrated condensate trap.
34
Connection for air extraction
Silencer
...with air extraction:
(optional accessory)
The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason the silencer must be
positioned as close as possible to the
ducting exit a.
...in recirculation mode:
The silencer needs to be positioned
between the fan and the exhaust grille
b. The space needs to be checked in
some cases.
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.
...air extraction with external motor:
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
c if possible, or if the ducting is long,
then in the ducting inside the cooker
hood itself d.
In the case of an external motor placed
inside the house, fitting a silencer
behind the external motor e reduces
the noise of the motor outside the
house.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted
one behind the other in the system.
35
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations
(BS 7671 in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
When switched off there must be an
all-pole contact gap of 3 mm in the
switch (including switch, fuses and
relays according to EN 60335).
36
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Important
This appliance is supplied for
connection to an a.c. 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
Operation with Control module DSM 400
The Miele DSM 400 control module can
be used to combine the cooker hood
with other components.
It enables the following:
Potential free connection
This can be used to operate a further
appliance via the On/Off button s on
the cooker hood.
Components used in the central
ducting system are not supplied by
Miele.
If in any doubt, the advice of a
competent builder or, for gas, a Gas
Safe installer must be sought.
Connection to a light switch
The control module can be used to
switch on the cooker hood lighting and
also to dim it, depending on model, via
a light switch in the house.
Installation
The control module is fitted onto the
cooker hood housing.
The electrical connection of
components to the control module
must be carried out by a suitably
qualified and competent person.
The potential free contact on the
DSM 400 a can, for example, be used
in a cooker hood with an external motor
...EXT, which is connected to a central
ducting system.
The contact can then be used to
operate an electrically driven non-return
flap b which is connected to the
central extraction unit c.
37
Technical data
Total connected load*
DA 2250, DA 2270. . . . . . . . . . . . 300 W
DA 2210. . . . . . . . . . . . . . . . . . . . 780 W
– Fan motor
DA 2250, DA 2270 . . . . . . . . . . 200 W
DA 2210 . . . . . . . . . . . . . . . 2 x 290 W
– Hob lighting
DA 2250, DA 2270 . . . . . . . . 2 x 50 W
DA 2210 . . . . . . . . . . . . . . . . 4 x 50 W
Voltage . . . . . . . . . . . . . . . . . AC 230 V
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Fuse rating GB . . . . . . . . . . . . . . . . . 5 A
Fan performance*
Extraction power according to EN 61591
DA 2250, DA 2270:
Extraction system C 150 mm
Level I . . . . . . . . . . . . . . . . . . . 200 m3/h
Level II. . . . . . . . . . . . . . . . . . . 300 m3/h
Level III . . . . . . . . . . . . . . . . . . 400 m3/h
Level IV Intensive Setting . . . . 640 m3/h
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 140 m3/h
Level II. . . . . . . . . . . . . . . . . . . 240 m3/h
Level III . . . . . . . . . . . . . . . . . . 360 m3/h
Level IV Intensive Setting . . . . 550 m3/h
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrically suppressed
according to AS/NZS 1044
Electrical cable length . . . . . . . . . 1.5 m
Weight
DA 2250 . . . . . . . . . . . . . . . . . . . . . 8 kg
DA 2250 EXT . . . . . . . . . . . . . . . . 5.5 kg
DA 2270. . . . . . . . . . . . . . . . . . . . 9.5 kg
DA 2270 EXT . . . . . . . . . . . . . . . . . 7 kg
DA 2210 . . . . . . . . . . . . . . . . . . . . 16 kg
DA 2210:
Extraction system 2 x C 150 mm
Level I . . . . . . . . . . . . . . . . . . . 650 m3/h
Level II. . . . . . . . . . . . . . . . . . . 950 m3/h
Level III . . . . . . . . . . . . . . . . . 1250 m3/h
Level IV Intensive Setting . . . 1850 m3/h
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 600 m3/h
Level II. . . . . . . . . . . . . . . . . . . 900 m3/h
Level III . . . . . . . . . . . . . . . . . 1200 m3/h
Level IV Intensive Setting . . . 1550 m3/h
Special accessory for recirculation
mode:
* For EXT models,
– Conversion kit DUU 151
2 kits are required for the DA 2210
the rated load and extraction power will
depend on the type of external motor
fitted.
– Miele charcoal filter pack DKF 15-1
(each pack contains 2 filters)
2 packs are required for the DA
2210
38
Length of connection cable to external
motor. . . . . . . . . . . . . . . . . . . . . . . 1.9 m
39
Alteration rights reserved / 2613
M.-Nr. 09 723 630 / 00