mamaomo Software Product Description RSX-11S,

mamaomo Software Product Description RSX-11S,
Software Product Description
RSX-11 S is a memory-based real-time operating system designed to operate on a PDP-11 processor with
a minimum of 8K words of memory. The system is
not dependent upon any mass storage media for execution. RSX-11S is based on the RSX-11M disk-based
operating system and is fully subset compatible with
it. The I/O driver interface is identical. Device drivers
written for each system execute on the other. Further,
any application program that executes under RSX11 S will execute under RSX-11 M without change following a relink of the cbject program.
As a memory-based system, RSX-11S does not support a file system, non-resident tasks check pointing
(rollin/rollout), or overlays, or program development.
It provides a run-time environment for execution of
tasks on a memory-based processor. Since it is
based on RSX-11 M, RSX-11 S enjoys most of the i nherent features and generation capability of that system. RSX-11 S supports all of the peripheral devices
that are supported under RSX-11 M, including other
hardware features such as floating point processors,
parity memory, and memory management.
Tasks written in MACRO, FORTRAN IV, FORTRAN IVPLUS, or BASIC-PLUS-2 must be assembled or compiled and subsequently linked on the host system and
transported to the target RSX-11 S system for execution. Tasks written in FORTRAN require a minimum of
16K words of memory for the RSX-11 S target system.
Transportation of tasks between the RSX-11 M host
and the RSX-11 S target is provided via the File
Exchange Utility (FLX) on the host system and the
On-line Task Loader (OTL) on the target system.
RSX-11S requires an RSX-11M or RSX-11D, Version
6.2, system for host support and system generation.
The software components contained in the RSX-11S
distribution kit include the following:
Binary and Source Modules:
Monitor Console Routine - RSX-11 M Subset
On-line Task Loader
System Image Preservation Program
File Control Services (FCS) for record devices (does
not include directory support)
An RSX-11 M, Version 3.1, or RSX-11 D, Version 6.2,
system is required for system generation and program development.
June 1978
SPD 9.21.5
Version 2.1, Real Time Operating System
• Any PDP-11 processor (including the LSI-11 and
PDP-11/03) with at least 8K words of memory.
(Note: Only those devices marked by an asterisk (*)
are supported on the LSI-11 and PDP-11/03.)
• KW11-L, KW11-P, DL 11-W clock (other than PDP11/03 and LSI-11 only)
• *DLV11 line interface (PDP-11/03 and LSI-11 only)
• Hardware bootstrap loader
• One of the following load devices:
1. T A 11 cassette tape
2. PR 11 paper tape reader
3. PC11 paper tape reader/punch
4. TC11 DECtape
5. RX11 floppy disk system
6. *RXV11 floppy disk system (PDP-11 /03 and LSI11 only)
7. Tape system from Table T
Table T
Tape System
PDP-11 processors
Additional memory to a system total of 28K words on
systems that do not include the hardware memory
management unit, 124K words on other than PDP11/70 systems which include the hardware memory
management unit, or 1920K words on PDP-11170 systems.
KT11 memory management unit (requires a minimum
of 24K words of memory)
RSX-11S, Version 2.1
SPD 9.21.5
E11-A, B Extended Arithmetic Element (supported
only on systems which do not include a memory management unit)
KE11-E Extended instruction set
KE11-F Floating instruction set
FP11 Floating point processor
KW11- Y Watch-dog timer clock
*KEV11 Extended arithmetic chip
I/O Peripherals:
PR 11 paper tape reader or PC 11 paper tape readerlpunch
CR11 or CM11 card reader
VT11/VS60 Graphics Display processor scope, except
on PDP-11/70 when 22 bit addressing mode is enabled. VT11 data buffers must reside in first 28K
words of physical memory.
*LA3S, LA180 line printer
LS11, LP11 or LV11 line printer (no plotter support)
No directory support for any magnetic
tape or disk systems.
Magnetic tape devices:
TA 11 Dual drive cassette tape system
TC11 DECtape controller and dual transport
Tape system from Table T
Disk devices:
RX11 floppy disk system
*RXV11 floppy disk system (PDP-11/03 and LSI-11
RF11 fixed-head disk system
RL 11 disk cartridge controller with RL01 disk drives
RK11 or *RKV11 disk cartridge controller with RKOSJ
or RKOSF disk drives
RK611 disk cartridge controller with RK06 disk drives
RPR02 disk pack drives (with appropriate controller)
RP03 disk pack drives (with appropriate controller)
RP04, RPOS, or RP06 disk pack drives (with appropriate controller)
RS03 or RS04 fixed-head disks (with appropriate controller)
RM02/03 disk pack drives (with appropriate controller)
*LA30, LA36, LA180S, LT33, LT3S, VTOS, VTSO, VTS2,
VTSS terminals (MCR provides no escape sequence
support on VTSO, VTS2, VTS5). These terminals are
supported when connected to DH11 (with or without
DM11-BB), DZ11, DJ11, DL11-A, B, C, D or W, or, *
DLV11. *DLV11-J or DZV11.
*RT02 Alphanumeric Display
*RT02-C Alphanumeric Display and badge reader
DL 11-E and *DLV11-E single line interfaces
DP11 synchronous line interface
DU11 synchronous line interface
DUP11 synchronous line interface
DQ11 DMA synchronous line interface
DMC11 interprocessor link
*DUV11 synchronous line interface
Laboratory/Industrial Control:
AD01-D AID converter
AFC11 AID converter
DRS/DSS 11 industrial control system modules
UDC11 Universal Digital Controller
IDA11-AA Contact sense module
IDA 11-AB Contact sense module
IDA 11-BA Contact interrupt module
IDA11-BB Contact interrupt module
IDA 11-CA 1/0 converter
IDA11-DA Solid state AC/DC driver
IDA11-EA Flip-flop DC driver
IDA 11-FA Single shot driver
IDA 11-GA Latching output relay
IDA 11-HA Flip-flop output relay
IDA 11-JA Single shot output relay
IAA 11-AA Multi-range AID converter
IAA 11-BA DI A converter
IAA 11-BB DI A converter
IAA11-BC D/A converter
IAA 11-BD DI A converter
ICS11/1CR11 Industrial Control subsystem
IDC-IA Isolated DC sense
IDC-IB Isolated DC interrupt
IDC-IC 1/0 counter
IDC-ID Non-isolated DC sense
IDC-IE Non-isolated DC interrupt
lAC-I A Isolated AC sense
IAC-IB Isolated AC interrupt
IDC-OA DC flip-flop driver
IDC-OB DC single shot driver
IAC-OA AC flip-flop driver
lAC-DB AC single shot driver
IRL-OA Latching output relay
IRL-OB Flip-flop output relay
IDA-DB 4 channel DI A converter
IAD-IA 8 channel AID converter
IMX-IA 16 channel multiplexer for IAD-IA
Data Acquisition:
One or more of the following subsystems:
• LPS11 Laboratory Peripheral Systems. Requires:
LPS11-S, LPSAD-12, and LPSKW options:
1. LPSDR-A 16-bit digital 1/0 registers and relays
(bit interrupt capability not supported)
2. BA408/LPSAM-SG switch gain OR
LPSAM/LPSAM-E multiplexer
3. LPSVC 12-bit DI A converter
4. LPSDA Df A expander
• AR11 Analog Real-time Systems Options: DR11-K
16-bit digital I/O option. One per subsystem (bit
interrupt capability not supported)
• LPA 11-K Laboratory Peripheral Accelerator
• Laboratory 1/0 Subsystem configured using the following options:
1. ADK11-KT 12-bit AID converter with 16-channel
multiplexer and dual clock; one per subsystem.
2. AD11-K 12-Bit AID converter with 16-channel
multiplexer; 16 per subsystem (15 if ADK11-KT
is part of same subsystem).
SPD 9.21.5
RSX-11 S, Version 2.1
-33. KW11-K Dual real-time clock with Schmitt trigger; one per subsystem (clock already included
in ADK11-KT, no KW11-K required if one is present).
4. AM11-K 48-channel AID multiplexer with gain
ranging; 1 per AD11-K or ADK11-KT.
5. DR11-K 16-bit digital 1/0 option; 16 persubsystem.
6. AA 11-K 4-Channel 12-bit 0/ A converter with
scope control, 16 per subsystem.
7. *AAV11-A, *ADV11-A, *KWV11-A and *DRV11
real time options
RSX-11 M, Version 3.1, operating system or
RSX-11D, Version 6.2, operating system
CTS11 card reader/punch and XY11 or XY311 plotter
device drivers.
IP11 Process Control Subsystem (hardware and software available from Industrial Products Group).
A - Software Support will be provided as stated in
the Software Support Categories Addendum to this
Software Updates, if any, released by DIGITAL during
the one (1) year period following installation, will be
provided to the customer for a media charge (includes no installation). After the first year, updates, if
any, will be made available according to then prevailing DIGITAL poliCies.
All binary licensed software, including any subsequent updates, is furnished under the licensing
provisions of DIGITAL's Standard Terms and Conditions of Sale, which provide in part that the software
and any part thereof may be used on only the single
CPU on which the software is first installed, and may
be copied, in whole or in part (with the proper inclusion of the DIGITAL copyright notice and any DIGITAL
proprietary notices on the software) only for use on
such CPU. All source licensed software is furnished
only under the terms and conditions of a separate
Software Program Sources Agreement between Purchaser and DIG ITAL.
Standard options with no support services are only
available after the purchase of one supported license.
When a software license is ordered without support
services, the category of support applicable to such
software is Category C.
The following key (C, 0, E, N, T, Y, Z) represents the
distribution media for the product and must be specified at the end of the order number, e.g., QJ642-AD
= binaries on 9-track magnetic tape. Users using
RSX-11D as the RSX-11 S host can order the kit only
on RKOS, RK06, or 9-track magtape.
9-track Magnetic Tape
RKOS Disk Cartridge
TU60 Cassette
RK06 Disk Cartridge
RX01 Floppy Diskette
No hardware dependency
Standard Options
QJ642 -A- Single-use license, binaries, documentation, support services (media: C, 0, E,
N, T, Y)
QJ642 -C- Single-use license, binaries, documentation, no support services (media: C,
0, E, N, T, Y)
Update Options
Users of RSX-11S, whose specified Support Category
warranty has expired may order under license the following software update at the then current charge for
such update. The update is distributed in binary form
on the appropriate medium and includes no installation or other services unless specifically stated
QJ642 -H- Binaries, documentation (media: C, 0,
E, N, T, Y)
Users of RSX-11 S, Version 2, whose specified Support Category warranty has not expired may order
under license the following software update for the
then current media charge. The update is distributed
in binary form on the appropriate medium and includes no installation or other services unless specifically stated otherwise.
QJ642 -W- Binaries, documentation (media: C, 0,
E, N, T, Y)
Miscellaneous Options
QJ642 -G- Pre-delivery kit (media: Z)
RSX-11S, Version 2.1
SPO 9.21.5
Each software product (hereinafter 'SOFTWARE') with a designated Support Category A or B in the applicable Software Product
Description (SPD) existing at the time of order will be the current release at the time of delivery and will conform to the SPD.
DIGITAL's sole obligation shall be to correct defects (nonconformance of the SOFTWARE to the SPD) as described below. Any
SOFTWARE with a deSignated Support Category C will be furnished on an 'as is' basis.
For SOFTWARE with a deSignated Support Category A or S, DIGITAL will provide the services set forth below without additional
1. Upon notification by customer to the nearest DIGITAL office that the computer system, including all required prerequisite
hardware and software, is ready for the installation of the SOFTWARE, DIGITAL will install such SOFTWARE in any location
within the contiguous forty-eight (48) United States, the District of Columbia, or a country in which DIGITAL or a subsidiary
of DIGITAL has a software service faCility. The notification must be received by DIGITAL and the system must be ready for
installation within thirty (30) days after the delivery of the SOFTWARE to customer or DIGITAL will have no obligation to
install. Installation will consist of: (1) verification that all components of the SOFTWARE have been received by customer, (2)
loading the SOFTWARE, and (3) executing a DIGITAL sample procedure.
2. During the ninety (90) day period after installation, if the customer encounters a problem with the current unaltered release
of the SOFTWARE which DIGITAL determines to be a defect in the SOFTWARE, DIGITAL will provide the following remedial
service (on site where necessary): (1) if the SOFTWARE is inoperable, apply a temporary correction (TC) or make a
reasonable attempt to develop an emergency by-pass, and (2) assist the customer to prepare a Software PerformanCe
Report (SPR) and submit it to DIGITAL.
3. During the one (1) year period following installation, if the customer encounters a problem with the SOFTWARE which his
diagnosis indicates is caused by a SOFTWARE defect, the customer may submit an SPR to DIGITAL. DIGITAL will respond
to problems reported in SPRs which are caused by defects in the current unaltered release of the SOFTWARE via the
Maintenance Periodical for the SOFTWARE, which reports SPRs received, code corrections, temporary corrections, generally
useful emergency by-passes and/or notice of the availability of corrected code. Software Updates, if any, released by
DIGITAL during the one (1) year period, will be provided to the customer on DIGITAL's standard distribution media as
specified in the applicable SPD. The customer will be charged only for the media on which such updates are provided,
unless otherwise stated in the applicable SPD, at DIGITAL's then current media prices.
During the one (1) year period following delivery, the services provided to the customer will be the same as set forth in 3 above.
SOFTWARE is provided on an 'as is' basis. Any software services, if available, will be provided at the then current charges.
DIGITAL shall have the right to make additional charges for any additional effort required to provide services resulting from
customer use of other than current unaltered release of the SOFTWARE operated in accordance with the SPD.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF