Uniden TRU8885-2 Owner`s manual

TRU 8885
SERIES
OWNER'S
MANUAL
WELCOME/FEATURES
TERMINOLOGY
CONTROLS & FUNCTIONS
DISPLAY AND ICONS
SOFT KEY FUNCTION
GETTING STARTED
Setting up the Phone
Mounting the Base Unit on a Wall
Main Menu Options
Setting Menu Options
BASICS
Making and Receiving Calls
Flash and Call Waiting
Placing a Call on Hold
Redialing a Call
Adjusting the Earpiece and Speaker Volume
Do Not Disturb (DND)
Mute Microphone
Tone Dialing Switch-over
Traveling Out of Range
Privacy Mode
3 or 4-Way Conferencing
PHONEBOOK
Phonebook (Storing Phone Numbers, Names,
Distinctive Rings and Speed Dial)
Chain Dialing
Steps for Entering Names and Special Characters
Viewing the Phonebook
Making Calls Using the Phonebook
Speed Dialing
Editing or Erasing a Phonebook Entry
Copying Phonebook Entries
CALLER ID
Caller ID and CIDCW (Caller ID on Call Waiting)
Viewing the Caller ID List
[1]
Contents
2
3
4
6
8
9
9
13
15
16
Deleting a Caller ID Message
Using the Caller ID Message List
Call Waiting Deluxe Features
52
53
55
THE INTEGRATED ANSWERING DEVICE
The Integrated Telephone Answering Device
Turning the Answering System On/Off
Setting your outgoing message (Greeting)
Using the Answering Setup Menu
New Message LED
Using your Answering System
Remote Operation
33
EXPANDING YOUR PHONE
33
34
34
35
37
37
38
39
39
40
40
ADDITIONAL INFORMATION
42
42
43
44
46
47
47
48
49
50
50
51
Expanding Your Phone
Connecting the Charger
Register the Handset
Using DirectLink Mode
Intercom/Call Transfer Feature
56
56
57
57
58
58
59
63
67
67
68
68
70
71
Changing the Digital Security Code
Find Handset
Installing the Beltclip
Headset Installation
Note on Power Sources
Maintenance
General Information
74
74
74
75
75
76
76
77
TROUBLESHOOTING
78
Troubleshooting
Liquid Damage
78
81
PRECAUTIONS & WARRANTY
I.C. NOTICE
MEMORY LIST
INDEX
REMOTE OPERATION CARD
MAIN MENU FLOW CHART
82
84
85
86
88
90
www.uniden.com
Welcome
Congratulations on your purchase of the Uniden Multi-Handset Cordless System
telephone. This unit is different from conventional cordless telephones. When the base
unit is connected to AC power and a telephone line, it can support up to 10 handsets.
You can now place a fully-featured cordless handset anywhere in your home or office
where AC power is available to connect the handset chargers. Extra handsets also allow
you to establish a 4-way conference call among 2 handsets, the base speakerphone, and
an outside line.
Note: Some illustrations in this manual may differ from the actual unit for explanation
purposes.
As an Energy Star® Partner, Uniden has determined that this product or product
models meets the Energy Star® guidelines for energy efficiency.
Energy Star® is a U.S. registered mark.
Features
www.uniden.com
5.8GHz Digital Expandable
Integrated Answering Device
Dual Keypad with LCD Screen at Base
10 Multi-Handset Expandability
Hands-Free Speakerphone in the Handset and Base
Caller ID/Caller ID on Call Waiting (subscribe through local telephone company)
Call Waiting Deluxe (subscribe through local telephone company)
100 Programmable Memory Locations
Trilingual Display Options and Voice Prompts (English, French and Spanish)
Intercom/Call Transfer Between Handsets
20 Distinctive Ring Options (10 ringer tones and 10 melody ringers)
Mute and Hold Features
Do Not Disturb (DND) Feature
DirectLink™ Mode
Room/Baby Monitoring
Battery Level Indicator
Clock Display
Animation Displays
WELCOME/FEATURES [2]
WELCOME/FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This series features AutoTalk ™ and AutoStandby ™. AutoTalk allows you to answer a call by just removing
the handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to
hang up by simply returning the handset to the cradle.
To protect you against mis-billed calls that might result from your phone being activated by other
equipment, this series has Random Code ™ digital security, which automatically selects one of over
approx. 65,000 digital security codes for the handset and base.
Digital Spread Spectrum Technology uses a wider frequency band than standard digital transmissions. The
result is a more secure conversation with the clarity of digital sound, extended range, and minimal
interference from other cordless phones.
IntegriSound™ Built in sound quality which provides life-like conversations.
With DirectLink™ mode, you can use 2 or more handsets as radio transceivers (walkie-talkies).
Be sure to visit our web site: www.uniden.com
Uniden® is a registered trademark of Uniden America Corporation.
AutoTalk, AutoStandby, DirectLink, IntegriSound and Random Code are trademarks of Uniden America.
Terminology
[3] TERMINOLOGY
www.uniden.com
TERMINOLOGY
•Standby Mode - The handset is not in use, and talk/flash or speaker has not been pressed. No dial tone is
present.
•Talk Mode The handset is not in the cradle, and talk/flash or speaker has been pressed, enabling a dial tone.
Ta l k appears on the display.
Controls & Functions
1
5
14
6
2
7
3
8
9
10
15
16
17
11
12
13
18
19
4
20
21
Retrieve TAD message
with Handset Remote keys
Delete
www.uniden.com
Play
CONTROLS &
FUNCTIONS
Repeat
1. Handset Antenna
2. Beltclip Hole
3. Speakerphone Speaker and Ringer
4. Handset Battery Compartment
5. New Message LED
6. Handset Earpiece
7. LCD Display
8. soft Keys (P. 8)
9. cid/vol/ (volume up) (P. 37 & 16)
10.redial/p/vol/
(volume down) (P. 35, 33, 16 & 37)
11. */tone/< (P. 39 & 44)
12.speaker (P. 33)
13.intcom/hold (P. 71 & 34)
14.Headset Jack Cover
15.talk/flash (P. 33 & 34)
16.end (P. 33)
17.phonebook (P. 42)
18.#/> (P. 44)
19.
(Message) (P. 65)
20.Handset Microphone
21.Handset Charging Contacts
Skip
Stop
CONTROLS & FUNCTIONS [4]
22
23 24
32
40
41
33
34
25
35
26
36
37
38
27
28
29 30
39
31
30. do not disturb (P. 37)/DND LED
31. /tone (P. 39)
32. Message Counter Display
33. soft Keys (P. 8)
34. Base Speaker
35. speaker/speaker LED (P. 33)
36. phonebook (P. 42)
37. intercom/hold (P. 71 & 34)
[5] CONTROLS & FUNCTIONS
38. flash/find hs Key (P. 34 & 74)
39. /volume/ /
(volume up/down)
(P. 37 & 16)
40. DC IN 9V Jack
41. TEL LINE Jack
CONTROLS &
FUNCTIONS
22. In use LED
23.
play/stop (P. 59)
24. cid/exit (P. 51)
25. Charge LED
26. Base Charging Contacts
27.
delete message (P. 60)
28. mic (microphone)
29.
answer on/off (P. 57)
www.uniden.com
Display and Icons
Example of the standby mode display
•Handset
Ringer off icon (when the ringer is off)/ day of the week and time / battery icon
Handset ID and Banner
Number of new Caller ID calls received (If there are no new Caller ID messages,
the Handset ID appears here.)
570#
*CPFUGV
0GY%+&
/'07
•Base
* Status of your
Answering machine
** Number of message
*
0'9
#059'4
1((
** (7..
#PPQWPEG
10.;
Day of the week and time
Number of new Caller ID calls received
appears if you have a new message.
appears if you turn your answering system off.
appears when the message storage is full.
appears if you set your answering system to announce only.
ICON
Appears During
Standby
www.uniden.com
The Ringer off icon indicates that ringer is turned off.
Talk
The Mute icon appears when you mute the handset or base.
Talk
The Speaker icon appears when the handset speaker phone is used (handset only).
Talk
The Privacy icon appears when the Privacy Mode is turned on.
Talk
The Recording icon appears while recording a conversation.
DISPLAY AND ICONS [6]
D I S P L AY A N D I C O N S
Standby/Talk
DESCRIPTION
Battery icons indicate the handset battery status. This icon changes depending on
the battery status (empty, low, medium and full).
Animation Displays (Handset only)
The handsets have a variety of animation displays. Below are examples of the animation screens and
what they mean:
Turning on the phone
Hanging up the phone
9GNEQOG
2NGCUG9CKV
'PF
Confirmation (Done!)
Deleting (Deleted!)
&QPG
&GNGVGF
/'07
Making a call
Find Handset/Paging the Handset
6CNM
/76'
2CIKPI
/'07
Also, the animation display changes depending on the ringer volume setting.
4KPIGT8QNWOG
4KPIGT8QNWOG
4KPIGT8QNWOG
?
$#%-
1-
$#%-
1-
$#%-
Unavailable
Low Battery
1WV1H4CPIG
7PCXCKNCDNG
.QY$CVVGT[
/'07
[7] DISPLAY AND ICONS
/'07
www.uniden.com
D I S P L AY A N D I C O N S
Out of Range
1-
Soft Key Function
"Soft" keys are keys that change function during the operation of the phone. There are three soft keys on
the base and three on each handset.
The function of each soft key is determined by the icon that appears directly above it. For example, when
the base is in standby mode, pressing soft key 1 will redial the last number. When the base is in talk
mode, pressing soft key 1 will mute the microphone.
Complete information on the features controlled by the soft keys can be found under each feature.
In standby mode
Handset
570#
*CPFUGV
0GY%+&
/'07
Soft key 2
In talk mode
Base
570#
0GY%+&
4'&+#.
Soft key 1
/'07
4'%14&
Soft key 2
Soft key 3
Handset
Base
6CNM
522JQPG
Soft key 1
/'07
Soft key 2
www.uniden.com
/76'
Soft key 1
/'07
Soft key 3
SOFT KEY FUNCTION [8]
S O F T KE Y F U NC TI ON
/76'
note
For maximum range:
A. Choose the best location
When choosing a location for your new phone, here are some important guidelines
you should consider:
•Keep the antenna free
of obstruction.
•When the handset is
not in use place the
handset in an upright
position.
•Do not hold the
handset where you
would block the signal.
Correct
Incorrect
•Metal and reinforced
concrete may affect
cordless telephone
performance.
• The location should be close to both a phone jack and a continuous power outlet (one
which is not connected to a switch).
• The base and handset should be kept away from sources of electrical noise such as motors,
microwave ovens, and fluorescent lighting.
• For better reception, place the base as high as possible.
• The base should be placed in an open area for optimum range and reception.
• If your home has specially wired alarm equipment connected to phone line, be sure that
installing the system does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, contact your telephone company or a qualified
installer.
[9] GETTING STARTED
www.uniden.com
GETTING STARTED
Setting up the Phone
The handset is powered by a rechargeable battery pack. The battery recharges
automatically when the handset is placed in the base unit. To maximize the charge
capacity of your battery pack, DO NOT plug the telephone cord into the base unit
and wall jack until the battery is fully charged.
1) Press down on the handset battery case cover (use the
finger indention for a better grip) and slide the cover
downward to remove.
2) Turn the battery pack so that the connector with the red
and black wires is near the jack inside the battery
compartment. Match the connector's wire colors to the
polarity label in the battery compartment (the connector
notches fit into the grooves of the jack only one way).
Push the battery pack connector into the jack until it
clicks into place.
3) Make sure you have a good connection by gently pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.
4) Place the battery case cover back on the handset and slide
it upwards until it clicks into place.
5) Place the handset in the base unit for 15-20 hours without
interruption. The base unit's LED light (labeled charge)
illuminates once the handset is placed in the base. The
LED light will illuminate whether the battery pack is
connected or not.
www.uniden.com
note
The battery may be
purchased by calling
Uniden's Parts
Department (see back
cover page).
GETTING STARTED [10]
G E T T I N G S TA RT E D
B. Install the rechargeable battery pack into the handset, and
charge for at least 15-20 hours before using!
note
Even when the battery
pack is not being used,
it will gradually
discharge over a long
period of time.
For optimum performance,
be sure to return the
handset to the base unit
after each telephone call.
When the battery pack is very low, the phone is programmed to eliminate functions
in order to save power.
The battery pack needs to be charged when:
- The empty battery icon appears.
.QY$CVVGT[
- L ow B a tt e ry appears in the display.
If the phone is in standby mode, none of keys will
operate. If you are on a call, complete your conversation as quickly as possible, and
return the handset to the cradle.
Cleaning the battery charging contacts
To maintain a good charge, it is important to clean the
charging contacts on both the handset and the base
unit once a month. Using water only, dampen a cloth
to clean the charging contacts. Then make sure to go
back over the charging contacts with a dry cloth
before returning the handset to the base to charge.
contacts
Caution: Do not use paint thinner, benzene, alcohol,
or other chemical products. Doing so may discolor the
surface of the telephone and damage the finish.
[11] GETTING STARTED
www.uniden.com
GETTING STARTED
Low battery alert
1) Connect the AC adapter to the DC IN 9V jack and to a
standard 120V AC wall outlet.
Connect the AC adapter to a continuous power supply
(i.e., an outlet that is not controlled by a switch).
2) Set the base on a desk or tabletop, and place the
handset in the base unit.
Place the base unit close to the AC outlet so that
you can unplug the AC adapter easily.
3) Make sure that the charge LED illuminates.
If the LED does not illuminate, check to see that the
AC adapter is plugged in and the handset makes
good contact with the base charging contacts.
note
•Use only the supplied
[AD-830] AC adapter.
Do not use any other
AC adapter.
•Place the power cord
so that it does not
create a trip hazard or
where it could become
chafed and create a
fire or electrical
hazard.
After installing the battery pack in the handset,
charge your handset for at least 15-20 hours before
plugging into the phone line.
4) Once the handset battery pack is fully charged,
connect the telephone line cord to the TEL LINE jack
and to a telephone outlet.
If your telephone outlet isn't modular, contact
your telephone company for assistance.
www.uniden.com
GETTING STARTED [12]
G E T T I N G S TA RT E D
C. Connect the base unit
DO NOT use an AC outlet
controlled by a wall
switch.
GETTING STARTED
!
Mounting the Base Unit on a Wall
Standard wall plate mounting
This phone can be mounted on any standard wall plate.
1) Make the AC adapter and the telephone line cord
through the hole on the wall mount adapter.
2) Plug the AC adapter into the DC IN 9V jack.
3) Plug the telephone line cord into the TEL LINE
jack.
4) Slide the wall mount adapter into the notches on
the base.
5) Plug the AC adapter into a standard 120V AC wall
outlet. Hook the cord on the notch of the wall
mount adapter.
6) Plug the telephone line cord into the telephone
outlet. Hook the cord on the notch of the wall
mount adapter.
7) Align the mounting slots on the base with the
mounting posts on the wall. Then push in and
down until the phone is firmly seated.
To remove, push up
a tab on the wall
mount adapter as
shown.
[13] GETTING STARTED
www.uniden.com
If you don't have a standard wall plate, you can mount your phone directly to the
wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting location that could
cause a hazard when inserting screws into the wall.
• Try to mount your phone within 5 feet of a working phone jack to avoid excessive lengths.
• Make sure the wall material is capable of supporting the weight of the base and handset.
• Use #10 screws (minimum length of 1 & 3/8 inches) with anchoring devices suitable for
the wall material where the base unit will be placed.
1) Insert two mounting screws into the wall (with their
appropriate anchoring device), 3 & 15/16 inches
apart. Allow about 1/8 of an inch between the wall
and screw heads for mounting the phone.
2) Refer to steps 1 through 7 on page 13 to mount the
telephone.
www.uniden.com
GETTING STARTED [14]
G E T T I N G S TA RT E D
Direct wall mounting
• For Global Setup,
Answ. Setup, and
Deregister HS menu
options, make sure
the line is not in use
and the handsets are
within range of the
base.
• For a flow chart of
the main menu, see
page 90.
Your phone has seven main menu options: DirectLink Mode, Room Monitor,
Handset Setup, Base Setup, Answ. Setup, Global Setup and Deregister HS. You
can change Room Monitor, Answering Setup, and Global Setup settings from the
base or from any handset. DirectLink Mode, Handset Setup, and Deregister HS are
only available from a handset. Base Setup is only available from the base.
Default Settings
The default settings set from the factory match the features that most people use.
You may not need to change them. However, there are a number of options you
must set and entries you must make in memory to take full advantage of all the
phone features. The table below lists the default settings.
Function
Ringer Tone
Ringer Volume
Distinctive Ring
Auto Talk
Anykey Answer
Banner
Language
(LCD) Contrast
Key Touch Tone
Animation Screen
Room Monitor
(allow monitoring)
[15] GETTING STARTED
Handset
Base
Flicker
High
On
-
Off
-
Off
-
“ “
English
Level 5
On
-
On
-
On
-
Function
Day & Time
CW / CWDX
Dial Mode
Area Code
Security Code
Record Time
Ring Time
Message Alert
Call Screen
Handset
Base
SUN 12:00 AM
CW on/CWDX off
Tone
None
80
1 minute
Toll Saver
Off
On
www.uniden.com
G E T T I N G S TA RT E D
note
Main Menu Options
Entering the Menu
•Handset
1) In standby mode, press the MENU soft key.
2) Use volume up/down to move the pointer to a desired & K T G E V . K P M / Q F G
main menu (DirectLink Mode, Room Monitor, Handset 4 Q Q O / Q P K V Q T
*CPFUGV5GVWR
Setup, Base Setup, Answ. Setup, Global Setup, and
$#%$#%1Deregister HS).
3) Press the OK soft key to select the desired main menu. •Base
To return to the previous screen, press the BACK soft 4 Q Q O / Q P K V Q T
key.
$CUG5GVWR
4) Use volume up/down to select a desired submenu and # P U Y 5 G V W R
$#%$#%1then press the OK soft key to enter.
5) In the submenu option, use volume up/down to select
an item. Press the OK soft key to confirm your
selection. For detailed instructions, see the following
sections for the desired submenu option. To return to
the previous screen, press the BACK soft key.
6) To exit the menu, press end on the handset or cid/exit on the base.
www.uniden.com
GETTING STARTED [16]
G E T T I N G S TA RT E D
Setting Menu Options
note
You must have at least
two handsets to use
DirectLink Mode.
In DirectLink mode, a pair of handsets can function as two-way radios. DirectLink
Mode allows two handsets to communicate with each other without the base unit or
a telephone line. Use them at sporting events or while shopping to stay in contact
with family members or friends. You must set both handsets to DirectLink Mode
activate this feature.
Using DirectLink Mode
1) Enter the DirectLink Mode menu. To en te r D i re c tL in k
m o de p r es s [ E NT E R] appears.
2) Press the ENTER soft key to enter the DirectLink Mode.
You will hear a confirmation tone, and D i re c tL i nk M od e
C o mp le t e appears.
3) To return back to the normal mode, press the CANCEL
soft key and then the OK soft key, or return the handset
to the cradle.
[17] GETTING STARTED
6QGPVGT
&KTGEV.KPMOQFG
RTGUU='06'4?
$#%-
$#%-
'06'4
www.uniden.com
G E T T I N G S TA RT E D
DirectLink Mode (Handset only)
G E T T I N G S TA RT E D
Room/Baby Monitor
This feature allows you to monitor
sounds in another room. Place the base
or a handset in the room you wish to
monitor; it will function as a
microphone. A second handset can be
set to function as a remote speaker,
allowing you to monitor sounds in the
room.
Monitor using
handset or
base unit
Using Room/Baby Monitor
1) Enter the Room Monitor menu (see
"Entering the Menu" on page 16).
L i st e n t o; appears.
2) Select the handset or base you want
to monitor by using volume up/
down.
3) Press the OK soft key.
M o ni t or i ng appears, and you hear sounds in the room
where the handset or the base is installed.
4) To turn off the Room Monitor, press the END soft key,
or end.
/QPKVQTKPI
㨭㨭*CPFUGV
'0&
If you want to prevent other handsets or the base from monitoring this handset,
press the MENU soft key. Select the Handset Setup menu, and then the Room
Monitor submenu. Select Of f and press the OK soft key.
www.uniden.com
GETTING STARTED [18]
The following submenu options must be set separately for each handset and the
base.
Selecting a Ringer Volume
Ringer volume lets you choose from one of three ringer volumes.
From the handset
1) Press the MENU soft key. Select the Handset Setup menu, and then the Ringer
Volume submenu.
2) Press volume up/down to select H I GH , L OW, or O F F.
3) Press the OK soft key. You will hear a confirmation tone.
From the base
In standby mode, press volume up/down to select one of three ringer volumes (Off,
Low, or High).
Selecting a Ringer Tone (Handset only)
Ringer tone lets you choose from 10 ringer tones or 10 melodies:
- Ringers (Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board,
Chip Chop, Party Clap, Reminder)
- Melodies (Beethoven's Symphony #9 [Beethoven9], For Elise [Elise], We Wish You A Merry
Christmas [Merry- Xmas], Home Sweet Home [Hm Swt Hm], Lorri Song #6 [Lorri Song],
When the Irish Eyes Are Smiling [Irish Eyes], Aura Lee, Let Me Call You Sweet Heart
[Sweetheart], Star Spangled Banner [Star Spngl], Old MacDonald [Old MacDld])
[19] GETTING STARTED
www.uniden.com
G E T T I N G S TA RT E D
Handset Setup / Base Setup
Distinctive Ringer Setup (Handset only)
Distinctive Ringer allows you to assign a designated ring tone to a stored
phonebook number. When a call is received and the Caller ID information matches
the information in one of the phonebook memory locations, the phone uses the
distinctive ring assigned to that particular Caller. You can assign distinctive rings
to multiple phonebook memory locations. Switching the setting to Distinctive Off
disables distinctive ringing: all incoming calls will have a normal ring tone.
Switching to Distinctive On activates all programmed distinctive ring memory
locations.
1) Enter the Handset Setup menu, and then the Distinct.
Ring submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select On or Of f .
3) Press the OK soft key. You will hear a confirmation
tone.
www.uniden.com
&KUVKPEVKXG4KPI
1P
1HH
$#%-
&'.'6'
1-
GETTING STARTED [20]
G E T T I N G S TA RT E D
1) Enter the Handset Setup menu, and then the Ringer
4KPIGT6QPGU
Tones submenu (see "Entering the Menu" on page 16). ( N K E M G T
%NCVVGT
2) Press volume up/down to move the pointer. You will
$#%&'.'6'
1hear the ringer or melody as you scroll through the
options.
3) Press the OK soft key. You will hear a confirmation tone.
AutoTalk allows you to answer the phone simply by removing the handset from the
cradle. You do not have to press any buttons to answer the call.
1) Enter the Handset Setup menu, and then the AutoTalk
submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select O n or O f f .
3) Press the OK soft key. You will hear a confirmation
tone.
#WVQ6CNM
1P
1HH
$#%-
&'.'6'
1-
Setting the Anykey Answer (Handset only)
Anykey Answer allows you to answer the phone by pressing any number key,
*/tone/<, or #/> on the handset.
1) Enter the Handset Setup menu, and then the Anykey
Answer submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select O n or O f f .
3) Press the OK soft key. You will hear a confirmation tone.
[21] GETTING STARTED
#P[MG[#PUYGT
1P
1HH
$#%-
&'.'6'
1-
www.uniden.com
G E T T I N G S TA RT E D
Setting the AutoTalk (Handset Only)
True Banner lets you customize the name your handset displays.
The name will be displayed on the LCD screen during Standby Mode, Intercom,
Intercom Hold, Room Monitor and Copy Phonebook operation. The banner name will
be displayed on the receiving handset as well.
1) Enter the Handset Setup menu, and then the Banner
submenu (see "Entering the Menu" on page 16).
2) Use the number keypad (0-9), */tone/<, #/>, or the
DELETE soft key to enter or edit the name.
3) Press the OK soft key. You will hear a confirmation
tone.
$CPPGT
/
AQ
AO
A
AU
A2
AJ
AQ
AP
AG
A
$#%-
&'.'6'
1-
Selecting a Language
Language selects which language the menu display will use. Choose from English,
French, or Spanish.
1) Enter the Handset Setup or the Base Setup menu, and . C P I W C I G
then the Language submenu (see "Entering the Menu" ' P I N K U J
on page 16).
(TCP㩟CKU
$#%2) Press volume up/down to choose En g li s h , F r an ﾕ a is
(French), or E sp a ﾂ ol (Spanish).
3) Press the OK soft key. You will hear a confirmation tone.
www.uniden.com
1-
GETTING STARTED [22]
G E T T I N G S TA RT E D
Setting the True Banner (Handset only)
Contrast adjusts the handset LCD brightness. Choose one from the 10 levels for
optimum viewing.
1) Enter the Handset Setup or the Base Setup menu, and then the LCD Contrast (for
handset) or the Contrast (for base) submenu (see "Entering the Menu" on
page 16).
2) Press volume up/down to adjust the contrast of the LCD (10 levels).
3) Press the OK soft key. You will hear a confirmation tone.
Setting the Key Touch Tone (Handset only)
Key Touch Tone is the tone your keypad makes when keys are pressed. You can turn
this tone on or off.
1) Enter the Handset Setup menu, and then the Key Touch
Tone submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select O n or O f f .
3) Press the OK soft key. You will hear a confirmation
tone.
[23] GETTING STARTED
-G[6QWEJ6QPG
1P
1HH
$#%-
&'.'6'
1-
www.uniden.com
G E T T I N G S TA RT E D
Adjusting the LCD Contrast
The Animation Screen displays animation on the handset LCD (see page 7). The
animations will be displayed on the LCD screen during a call, ringer volume setting,
paging operation, when you hang up and so on.
note
1) Enter the Handset Setup menu, and then the Animation # P K O C V K Q P 5 E T G G P
Screen submenu (see "Entering the Menu" on page 16). 1 P
1HH
2) Press volume up/down to select On or Of f .
$#%&'.'6'
13) Press the OK soft key. You will hear a confirmation
tone.
See "Animation Displays (Handset only)" on page 7 for all the available screens.
Answering System Setup
This main menu option allows you to set up the built in answering device.
Record a Personal Outgoing Message (Base Only)
Record Greeting allows you to record a personal outgoing message (greeting) which
the answering system automatically plays when you receive a call.
1) Enter the Answ. Setup menu, and then the
6QTGEQTF
Record Greeting submenu (see "Entering the I T G G V K P I
Menu" on page 16). To record greeting press R T G U U = 5 6 # 4 6 ?
$#%/'07
56#46
[ S TA R T] appears.
2) Press the START soft key. You will hear “Record Greeting.“ The message counter
displays 30 and then begins to count down.
www.uniden.com
•The greeting must be
more than 2 seconds
long, or it will not be
recorded.
•To delete the personal
outgoing message,
press the DELETE soft
key while the message
is playing. The system
announces “Greeting
has been deleted.“
GETTING STARTED [24]
G E T T I N G S TA RT E D
Setting the Animation Screen (Handset Only)
Selecting Your Greeting (Base only)
Select Greeting allows you to choose between the two outgoing messages, a prerecorded message or your own greeting.
1) Enter the Answ. Setup menu, and then the
2NC[DCEM
Select Greeting submenu (see "Entering the
ITGGVKPI
Menu" on page 16). Pl a y b ac k g re e ti n g
4'&+#.
5612
%*#0)'
appears, and the current outgoing message is &'.'6'
played. LCD is an example if you recorded your greeting.
2) Once you have recorded a personal greeting, press the CHANGE soft key to
choose the greeting. The selected outgoing message is played. Each time you
press the CHANGE soft key, the phone switches the outgoing message between
the prerecorded and the personal outgoing message.
Setting a PIN Code
Security Code selects a two-digit Personal Identification Number (PIN) code. A PIN
code is required to play your messages from a remote location.
1) Enter the Answ. Setup menu, and then the Security
Code submenu (see "Entering the Menu" on page 16).
2) Enter a two-digit PIN code (01-99) using the number
keypad (0-9).
[25] GETTING STARTED
5GEWTKV[%QFG
A
A
$#%-
&'.'6'
1-
www.uniden.com
G E T T I N G S TA RT E D
3) Position yourself near the base microphone and record your greeting.
4) When you are finished recording, press the STOP soft key. Your greeting will
playback for confirmation.
Setting the Ring Time
Ring Time allows you to set the number of rings the caller hears before your
answering system plays the outgoing message. You can set the ring time to answer
after two, four, or six rings. If you enable the Toll Saver (TS), the answering system
picks up after two rings if you have new messages and after four rings if there are
none.
1) Enter the Answ. Setup menu, and then the Ring Time
4KPI6KOG
submenu (see "Entering the Menu" on page 16).
6QNN5CXGT
6KOGU
2) Press volume up/down to select a Ring Time (Toll
$#%&'.'6'
Saver, 2 Times, 4 Times, or 6 Times).
3) Press the OK soft key. You will hear a confirmation tone.
1-
Setting the Record Time
Record Time sets the duration for recording the incoming messages. You have three
record time options. The options "1 minute" or "4 minutes" set the duration for
recording the incoming messages. "Announce only" answers the call but prevents
the caller from leaving a message.
1) Enter the Answ. Setup menu, and then the Record
4GEQTF6KOG
Time submenu (see "Entering the Menu" on page 16). / K P W V G
/KPWVGU
2) Press volume up/down to select Record Time
$#%&'.'6'
1(1 Minute, 4 Minutes, or Announce Only).
3) Press the OK soft key. You will hear a confirmation tone.
www.uniden.com
GETTING STARTED [26]
G E T T I N G S TA RT E D
3) Press the OK soft key. You will hear a confirmation tone.
Message Alert sounds an alert tone when you have an unheard message. If you set
the Message Alert on, the alert tone will sound every 15 seconds when a new
message is received.
1) Enter the Answ. Setup menu, and then the Message
Alert submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select O n or O f f .
3) Press the OK soft key. You will hear a confirmation
tone.
/GUUCIG#NGTV
1P
1HH
$#%-
&'.'6'
1-
Turning the message alert tone off by pressing any key
To quickly turn off the Message Alert tone, press any key on the base unit; the tone
will automatically deactivate.
Turning the message alert tone off from a remote location
When all new messages are played back using the remote playback feature (see
pages 63 to 66), the Message Alert tone will automatically deactivate. The tone will
not deactivate until all new messages are played back.
[27] GETTING STARTED
www.uniden.com
G E T T I N G S TA RT E D
Setting the Message Alert On or Off
Language allows you to set the language of your answering system announcements
to English, French, or Spanish.
1) Enter the Answ. Setup menu option, and then the
.CPIWCIG
Language submenu (see "Entering the Menu" on
'PINKUJ
(TCPCKU
page 16).
$#%&'.'6'
2) Press volume up/down to choose En g li s h , F r an ﾕ a is
(French), or E sp a ﾂ ol (Spanish).
3) Press the OK soft key. You will hear a confirmation tone.
1-
Setting the Call Screen
Call screen allows you to listen to an incoming call before answering.
1) Enter the Answ. Setup menu and then the Call Screen
submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select On or Of f .
3) Press the OK soft key. You will hear a confirmation
tone.
www.uniden.com
%CNN5ETGGP
1P
1HH
$#%-
&'.'6'
1-
GETTING STARTED [28]
G E T T I N G S TA RT E D
Setting the Language of your Answering System
note
•Any changes to the
global settings menu
affect all registered
handsets and the base.
•For setting the Day and
Time, the idle time-out
is extended to 2
minutes.
If you change one of the global settings, you change that setting for all additional
handsets. Only one handset can change global settings at a time.
Setting Day and Time
Day & Time sets the day and time of your display.
1) Enter the Global Setup menu, and then the Day & Time & C [ 6 K O G
submenu option (see "Entering the Menu" on
/10#/
=?
page 16). Image is for the base.
$#%5#8'
2) Press volume up/down to select the day of the week,
and then the → soft key.
3) Press volume up/down to set hour, and then press the → soft key.
4) Press volume up/down to set minute, and then press the → soft key.
5) Press volume up/down to choose A M or PM , and then press the SAVE soft key. You
will hear a confirmation tone.
[29] GETTING STARTED
www.uniden.com
G E T T I N G S TA RT E D
Global Setup
G E T T I N G S TA RT E D
Setting CIDCW (Caller ID on Call Waiting)
CIDCW sets the Caller ID on Call Waiting (CIDCW) displays the name and number of
an incoming call while you are on the line. Call Waiting Deluxe (CWDX) allows you
to handle call waiting calls in seven different ways.
1) Enter the Global Setup menu, and then the CIDCW
submenu (see "Entering the Menu" on page 16).
2) Press volume up/down to select C W O n /CW DX On , CW On /
C W DX Of f , or C W Of f /C WD X O ff , and then press the OK
soft key. You will hear a confirmation tone.
%+&%9
%91P%9&:1P
%91P%9&:1HH
$#%-
&'.'6'
1-
Setting the Area Code
If you enter a 3-digit area code number in the "Area Code" option, your local area
code does not appear in the Caller ID message. For calls received from outside your
local area code, you will see a full 10-digit number.
1) Enter the Global Setup menu, and then the Area Code # T G C % Q F G
submenu (see "Entering the Menu" on page 16).
㨫AA
2) Press the number keypad (0-9) to enter a 3-digit area
$#%&'.'6'
code.
3) Press the OK soft key. You will hear a confirmation tone.
www.uniden.com
1-
note
If the area code has
already been stored in
memory, the stored area
code will be displayed.
To change it, use the
DELETE soft key and
number keys to enter
the new area code.
GETTING STARTED [30]
Dial Mode sets the dial mode to tone or pulse. Most phone systems use tone dialing;
the default setting is tone dialing. Set the dialing mode to match the dialing
system used by your local phone service.
• If you are not sure of your dialing system, set the unit to tone dialing. Make a trial call. If
the call connects, leave the setting as is; otherwise set the unit to pulse dialing.
• If your phone system requires pulse dialing and you need to send DTMF tones in certain
situations during a call, you may switch over to tone dialing (refer to “Tone Dialing
Switch-over” on page 39).
1) Enter the Global Setup menu, and then the Dial Mode & K C N / Q F G
submenu (see "Entering the Menu" on page 16).
6QPG
2WNUG
2) Press volume up/down to select T o ne or Pu l se (the
$#%&'.'6'
initial setting is Tone).
3) Press the OK soft key. You will hear a confirmation tone.
[31] GETTING STARTED
1-
www.uniden.com
G E T T I N G S TA RT E D
Setting the Dial Mode
Deregister the handset's ID from the main base unit or the base ID from the
handset. Use this option, for example, when you change the digital security code
(see page 74).
1) In standby mode, select Deregister HS in the menu and & G T G I K U V G T * 5 !
press the OK soft key. D er e gi s te r H S? appears.
;GU
2) Press volume up/down to select Ye s and then the OK 0 Q
$#%&'.'6'
1soft key.
When de-registration is complete you will hear a confirmation tone, and
D e re g is t ra ti o n C om p le te appears.
3) After de-registering the handset, place the handset to the base to register.
www.uniden.com
GETTING STARTED [32]
G E T T I N G S TA RT E D
De-register the Handset (Handset only)
Making and Receiving Calls
note
•To set "AutoTalk", see
page 21 or to set
"Anykey Answer" see
page 21.
•If the line is in use by
another handset(s),
"L i ne In U s e "
appears in the base's
display, and "In Us e "
appears in the display
of all registered
handset's display that
are not in use.
•For the location of the
base microphone,see
"Controls and
Functions" on page 5.
Position yourself as
near to the base as
possible.
[33] BASICS
You can easily switch a call from
normal conversation to hands-free
conversation. To switch a call,
press speaker during the call.
6CNM
/76'
/'07
From the Handset
From the Base
Normal conversation
Hands-free conversation
Press speaker.
Handset On the Cradle
Pick up the handset (AutoTalk is:
on) or pick up the handset and press
talk/flash (AutoTalk is: off).
To answer a call
Handset Off the Cradle
Handset Off the Cradle
Press speaker.
Press any number key, /tone/<, or
#/> (Any Key Answer), or press
talk/flash.
*
Handset Off the Cradle
1) Press speaker.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then press
speaker.
To make a call
Handset Off the Cradle
1) Press talk/flash.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then press
talk/flash.
To hang up
Press end or return the handset to the cradle (AutoStandby).
To enter a pause
within the dialing When you dial the number in standby mode, press redial/p/vol/
P appears in the display, which represents a pause.
sequence
1) Press speaker.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then press
speaker.
Press speaker.
.
When you dial the number in
standby mode, press the PAUSE
soft key.
www.uniden.com
BASICS
•The handset
microphone is located
at the bottom of the
handset (see "Controls
and Functions" on
page 4). Position
yourself as near to the
handset as possible
and speak clearly.
This handset has a built-in speakerphone that allows you to
have a hands-free conversation. This feature allows you to easily
communicate while performing other tasks, such as cooking.
appears on the display during hands-free conversations.
Flash and Call Waiting
note
If you have Call Waiting service and a call waiting
tone sounds while you are on a call, press talk/flash
on the handset or flash/find hs on the base to accept
the waiting call. There is a short pause, and then you
will hear the new caller. To return to the original
caller, press talk/flash on the handset or flash/find
hs on the base again.
•If the battery pack is
completely drained,
the handset will not
beep when paging.
Placing a Call on Hold
1) During a call, press intcom/hold on the handset or
intercom/hold on the base. The call will be put on
hold (image is for the base).
*QNFVQVTCPUHGT
*CPFUGV
*CPFUGV
$#%-
&'.'6'
•While a call is on hold,
CIDCW can not be
received.
1-
If you leave a call on hold for more than 10 seconds, the base display screen will read,
L in e O n H ol d and handset display screen will read Ho l d .
2) To talk to the caller, press talk/flash or speaker on a handset (or speaker on the
base). The phone will return back to the call.
www.uniden.com
BASICS [34]
BASICS
•You can place a call on
hold for 5 minutes.
When 5 minutes has
passed, the call is
disconnected, and the
phone returns to
standby mode.
Redialing a Call
note
•If the number exceeds
32 digits, only the first
32 digits are retained
in redial memory.
•If the redial memory is
empty, you will hear a
beep.
1) With the phone in standby mode, press redial/p/vol/ on the handset or the
REDIAL soft key on the base.
2) Press volume up/down. Each press of volume up/down will display one of the
last three number redialed.
3) Press talk/flash or speaker on the handset (or speaker on the base). The
selected number is dialed.
4) To hang up, press end or return the handset to the base (or press speaker on the
base).
You can also display the redial list for redial number with the handset in talk mode.
Press the MENU soft key, then select the redial menu. Press volume up/down to
select the number you want to dial. Press the DIAL soft key to redial the number.
Deleting a Redial Record (Handset only)
1) Press redial/p/vol/ in standby mode.
2) Press volume up/down repeatedly to display the
number to be deleted.
3) Press the EDIT soft key, and then select D e le t e? .
4) Press volume up/down to choose Ye s .
5) Press the OK soft key. The redialed number is deleted.
[35] BASICS
&GNGVG4GFKCN!
;GU
0Q
$#%-
$#%-
1-
www.uniden.com
BASICS
•Redial numbers stored
in the handset and the
base are independent
from each other.
The last three phone numbers dialed can be quickly redialed from the handset or
base.
Storing a Redial Record (from the handset only)
1) Press redial/p/vol/ in standby mode.
2) Press volume up/down repeatedly to display the number to be stored.
3) Press the EDIT soft key,, then select St o re i n to PB ? , and then the OK soft key.
4) To complete the setting, follow the steps 3-8 in "Phonebook (Storing Phone
Numbers, Names, Distinctive Rings, and Speed Dial)" on pages 42-43.
BASICS
www.uniden.com
BASICS [36]
Adjusting the Earpiece and Speaker Volume
Earpiece and Speaker Volume
You can select from among of six volume levels on the
handset, and ten levels on the base. Pressing volume
up/down on the handset or base during a call will
change the earpiece or speaker volume. This setting
will remain in effect after the telephone call has ended.
BASICS
If you press volume up when the earpiece is at the
maximum volume level, an error tone sounds.
The error tone also sounds if you press volume down
at the lowest volume.
Do Not Disturb (DND)
The do not disturb feature (DND) allows you to mute the ringer, the base, and any
registered handsets at the same time. The phone must be in standby mode. Press
and hold do not disturb on the base. You will hear a confirmation tone, and the
DND LED illuminates. To cancel the DND feature, press do not disturb again. You
can also mute the ringer tone while the phone is ringing by pressing do not disturb
on the base.
Activating the DND while the answering system is off will turn the answering
system on automatically. The answering system setting will reset to the original
setting when you cancel the DND.
[37] BASICS
www.uniden.com
If you press answer on/off when the DND and the answering system is on, both of the
DND and the answering system will turn off.
To mute the ringer tone temporarily for each handset or the base, when the phone
is ringing, press end or the MUTE soft key on the handset or the base. The ringer
tone will return to the previous setting starting with the next incoming call.
Mute Microphone
www.uniden.com
•The tone feature only
applies when the dial
mode is set to pulse.
•This special number
can be stored in a
memory location. This
is referred to as Chain
Dialing (see page 43).
BASICS
You can temporarily mute the microphone so that the caller cannot hear you. Press
the MUTE soft key during talk mode (while the phone is in use) to mute the
appear in the display. To cancel muting, press the
microphone. M ut e O n and
MUTE soft key again. Mu t e O ff appears.
note
BASICS [38]
Tone Dialing Switch-over
Some telephone companies use equipment that
requires pulse dialing (sometimes referred to as rotary
dialing). If you need to enter tone dialing digits, you
can switch to tone dialing during the call. This
feature is useful when you need tone dialing to use
automated systems. For example, you can call your
bank's telephone teller system, then switch over to
tone dialing to enter your bank account number and
make menu selections.
BASICS
Initially make your call with pulse dialing mode. Once
your call connects, press */tone/< on the handset or
base to enter tone dialing mode. Any digits entered
will be sent in tone dialing mode. Once the call ends,
tone mode is canceled, and pulse dialing mode
resumes.
Traveling Out of Range
During a call, as you begin to move your handset too far from your base unit, noise
may increase. If you pass the range limits of the base unit, you will hear a beep and
see Ou t of Ran ge on the display, and then the handset returns to standby mode. You
may return to the call if you move your handset within the range limits of the base
and press talk/flash or speaker within 30 seconds.
[39] BASICS
www.uniden.com
Privacy Mode
Privacy Mode prevents interruption from other registered handsets or the base. This
works only when the phone is in use.
1) Press the MENU soft key on the handset or base during talk mode.
2) Press volume up/down to move the pointer to P ri va cy M od e and then the OK soft
key.
P r iv a cy Mo de On and
appear in the display. To exit the Privacy Mode, repeat
above step again when the Privacy Mode is on. Pr i va c y Mo d e O ff appears.
3 or 4-Way Conferencing
note
If someone is using
another handset in
Privacy Mode, S y st em
B us y P l ea s e tr y
l at e r appears in the
display when you try to
join the call.
BASICS
If you have more than one handset, up to four people can participate in a
conference call.
3-Way Conferencing
•Outside line > Handset > Base
4-Way Conferencing
•Outside line > Handset > Handset > Base
When speaking on the handset
1) Press speaker on the base to initiate the
3-conference call.
2) To hang up, press speaker on the base. The handset
will still be connected to the call.
www.uniden.com
BASICS [40]
When speaking on the base
1) Press talk/flash or speaker on the handset to
initiate the 3 or 4-conference call.
2) To hang up, return the handset to the cradle, or
press end on the handset. The base will still be
connected to the call.
BASICS
[41] BASICS
www.uniden.com
Phonebook (Storing Phone Numbers, Names, Distinctive
Rings and Speed Dial)
You can store names and numbers in your phone’s phonebook, search for names
alphabetically, and dial phonebook entries with just a few key presses. You can
store up to 100 numbers in the base and up to 100 additional numbers in each
registered handset.
The phone uses the same memory to store phonebook entries and Caller ID
messages. If the shared memory is already full, the phone will not store any more
phonebook entries. You will have to delete some of the Caller ID messages before
you can store a new phonebook entry.
www.uniden.com
•Selecting a phonebook
entry where a number
is already stored
overwrites the old
number. The new
number will be stored
in the phonebook entry.
•When the memory is
full, you will hear a
beep and Memory Full
appears. You will have
to delete some Caller ID
messages before you
can store new
phonebook entries.
•The pause key counts
as one digit. Pressing
the PAUSE soft key on
the base or redial/p/
vol/
on the handset
more than once
increases the length of
the pause between
numbers. Each pause
represents a 2 second
delay.
PHONEBOOK [42]
PHONEBOOK
1) When the phone is in standby mode, press phonebook. 2 J Q P G D Q Q M 2) Press the STORE soft key, S t or e /E di t N a me appears.
5GCTEJ=#<㨲㨱?
5VQTG=5614'?
3) Enter the name (up to 16 characters) by using the
%12;
5614'
number keypad (see the "Steps for Entering Names and $#%•
Base
Special Characters" on page 44).
If a name is not required, go to step 4. <No Name> will
2 J Q P G D Q Q M
be used as the name.
6 Q V C N 4) Press the OK soft key to store the name;
5GCTEJ=#<㨲㨱?
%12;
5614'
&'.'6'
S t or e /E d it N o . appears.
5) Use the number keypad, */tone/<, or #/> to enter the • Handset
phone number (up to 20 digits).
If you make an error, use the DELETE soft key to erase
the incorrect digits. When you are finished, press the
OK soft key to store the number.
note
6) If you store the phonebook entry from the handset,
D i st in c ti v e R in g appears. Press volume up/down to
move the pointer to one of the Distinctive Ring options
and then press the OK soft key.
note
7) Speed Dial appears. Press volume up/down to move the
pointer to select the Speed Dial location (10 locations:
SPD1-SPD0).
•If you choose not to
store a Distinctive
Ring, simply select the
"No Selectn" option.
&KUVKPEVKXG4KPI
0Q5GNGEVP
(NKEMGT
$#%-
1-
5RGGF&KCN
0Q5GNGEVP
52&'ORV[
$#%-
•If you choose not to
store the name/
number as a Speed
Dial, simply choose the
"No Selectn" option.
&'.'6'
8) Press the OK soft key. You will hear a confirmation tone, and
display.
Done!
&'.'6'
1-
appears in the
Chain Dialing
The memory locations in the handset are not limited to phone numbers. You can
also store a group of numbers (up to 20 digits) that you need to enter once your
call connects. This is referred to as Chain Dialing.
[43] PHONEBOOK
www.uniden.com
PHONEBOOK
An example of this is a bank account number. Store the account number in one of
the phonebook locations (refer to "Phonebook (Storing Phone Numbers, Names,
Distinctive Rings and Speed Dial)" on page 42). When you call your bank and are
prompted to enter the account number, scroll through your phonebook locations
until you find your account number, and then press the DIAL soft key.
Steps for Entering Names and Special Characters
Refer to the letters on the number keys to select the desired characters. With each press
of a number key (0-9), the displayed character appears in the following order:Upper case
letters first, lower case letters next and finally the number corresponding to the key.
Number of times key is pressed
www.uniden.com
PHONEBOOK [44]
PHONEBOOK
If you make a mistake while entering a name
Use */tone/< or #/> to move the cursor to the incorrect character.
Press the DELETE soft key to erase the wrong character, and then enter the correct
character. To delete all characters press and hold the DELETE soft key.
note
If the next character
uses the same number
key, you must press #/
> to move the cursor
over. Otherwise the next
time you press the
number key, it changes
the character that was
previously set.
For example, to enter Movies:
1) When the phone is in standby mode, press phonebook and the STORE soft key.
S t or e/ E di t N a me appears.
2) Press 6 once, and then press #/> to move the cursor to the right.
3) Press 6 six times.
4) Press 8 six times.
5) Press 4 six times.
6) Press 3 five times.
7) Press 7 eight times.
8) When finished, press the OK soft key.
To continue to store the telephone number, proceed to step 5 in “Phonebook
(Storing Phone Numbers, Names, Distinctive Rings, and Speed Dial)” on page 42.
PHONEBOOK
[45] PHONEBOOK
www.uniden.com
Viewing the Phonebook
Your phone stores names/numbers in the phonebook memory entries, and you can
search names in alphabetical order. You can view the phonebook even while the
phone is in use.
1) Press phonebook. If you open the phonebook during a 2 J Q P G D Q Q M call, only the BACK soft key will appear.
5GCTEJ=#<㨲㨱?
5VQTG=5614'?
2) Press volume up/down, or the number keypad to
$#%%12;
5614'
scroll through the phonebook entries. Phonebook
•
Base
entries appear in alphabetical order (from first to last
when you press volume down, from last to first when 2 J Q P G D Q Q M
6 Q V C N you press volume up).
5GCTEJ=#<㨲㨱?
%12;
5614'
&'.'6'
You can also use the letters on the number keys to
• Handset
select the first letter of the desired name. Press a
number key (2-9 and 0) once for the first letter, twice for the second letter, and
so on. The first entry that begins with the letter you entered appears.
For example, to search for Movies, press 6 once. Press volume up/down, until the
phonebook entry is displayed.
From Handset - press end (or the BACK soft key or talk/flash during a call).
From Base
- press cid/exit key or the BACK soft key.
www.uniden.com
During a call, don't
press end on the
handset or the call will
be disconnected.
PHONEBOOK [46]
PHONEBOOK
3) To finish the viewing operation:
note
Making Calls Using the Phonebook
From Standby Mode
1) When the phone is in standby mode, select the phonebook entry you want to dial
(see "Viewing the Phonebook" on page 46).
2) Press talk/flash or speaker on the handset or speaker on the base. The
displayed number is dialed.
3) To hang up press end on the handset (or press speaker on the base or return the
handset to the base).
From Talk Mode
1) Press talk/flash or speaker on the handset or speaker on the base.
2) Select the phonebook entry you want to dial (see "Viewing the Phonebook" on
page 46).
3) Press the DIAL soft key. The number in the displayed phonebook location is
dialed.
4) To hang up press end on the handset (or press speaker on the base or return the
handset to the base).
Speed Dialing
[47] PHONEBOOK
www.uniden.com
PHONEBOOK
If you store a phone number in a speed dial memory location (10 locations: SPD1 SPD0), you can use the speed dialing feature. When the phone is in standby mode,
press and hold a number key (0-9) associated with the speed dial until the phone
number appears, and then press talk/flash or speaker on the handset or speaker
on the base. The number stored in the speed dial (SPD1 - SPD0) is dialed.
Editing or Erasing a Phonebook Entry
1) When the phone is in standby mode, press phonebook.
2) Press volume up/down, or the number keypad to select the phonebook entry you
want to edit or delete. (see "Viewing the Phonebook" on page 46).
a. Editing the Stored Data
1) When the phonebook entry to be edited appears, press the EDIT soft key. For the
handset,then select E d it ? . St o re / Ed i t N am e appears.
2) Follow the steps 3 to 7 under "Phonebook (Storing Phone Numbers, Names,
Distinctive Rings, and Speed Dial)" on pages 42-43 to complete the editing
operation.
3) Press the OK soft key. You will hear a confirmation tone.
www.uniden.com
&GNGVG/GOQT[!
;GU
0Q
$#%-
$#%-
1-
PHONEBOOK
b. Deleting the Stored Data
1) When the phonebook entry to be deleted appears,
press the DELETE soft key on the base or the EDIT soft
key on the handset. For the handset, then select
D e le t e? .
D e le t e M em or y ? appears.
2) Press volume up/down to move the pointer to Y e s .
3) Press the OK soft key. You hear a confirmation tone.
D e le t ed ! appears in the display.
PHONEBOOK [48]
note
Copying Phonebook Entries
If the memory entry on
the receiving
handset or base is full,
and can not store the
phonebook locations,
you will hear a beep.
Copy Phonebook allows you to transfer stored phonebook entries from handset to
handset or from base to handset (or from handset to base) without having to
manually re-enter names and numbers. You can transfer one memory (phonebook
entries) at a time, or all memory entries at once.
1) When the phone is in standby mode, press phonebook.
2) Press the COPY soft key.
3) Press volume up/down, to select the handset or base
which you want to transfer the phonebook entries to and
then press the OK soft key.
6QYJKEJWPKV!
*CPFUGV
*CPFUGV
$#%-
4) Press volume up/down to select One Memory or All
M e mo ri e s: and then press the OK soft key.
&'.'6'
%QR[2JQPGDQQM
1PG/GOQT[
#NN/GOQTKGUZZZ
$#%&'.'6'
If you select All Memories, Are you sure? appears on the
display screen.
Press volume up/down to select Ye s , and then press the OK soft key.
5) The phonebook entries will be transferred to the handset
(or the base). Copying and the receiving handset name (or
base) appear. When the transfer is completed Done
appears on the handset (or the base).
[49] PHONEBOOK
1-
6QUGNGEV
RJQPGDQQM
R T G U U = # < 㨲 㨱?
$#%-
%QR[KPI
*CPFUGV
%#0%'.
www.uniden.com
PHONEBOOK
If you select One Memory, press volume up/down, or
the number key (2-9 and 0) to select the phonebook
entry you want to export and then press the COPY soft
key.
1-
You must subscribe to Caller ID services through your local telephone provider to
use these features.
When the telephone rings, the Caller ID feature allows you to view the caller’s
name, phone number, date and time of call. With CIDCW (Caller ID on Call Waiting),
you will hear a call waiting tone while you are on a call, and the Caller ID data is
displayed. To accept the waiting call, press talk/flash on the handset or flash/find
hs on the base (see page 34). Additionally, you can dial a number stored in the
Caller ID list or save data to your phonebook.
Important:
Memory for Caller ID messages and phonebook entries (including Speed Dials) are
common, you can store up to 100 entries for each handset and the base. Caller ID
messages are not stored when you have 100 phonebook entries. When you have
stored total of 100 phonebook entries and Caller ID messages, the oldest Caller ID
message is overwritten.
The date and time received
Caller's name
Caller's phone number
2/
,CPG5OKVJ
$#%-
• Base
&'.'6'
2
7PKFGP%QTR
'&+6
5614'
• Handset
1) When the Caller ID message is received, the display shows the caller's phone
number along with the date and time. The incoming call information is stored in
the Caller ID record. If the Caller ID service includes the caller's name, the name
will appear in the display (up to 15 characters).
www.uniden.com
note
•If you answer a call
before the Caller ID
message is received
(for example, before
the second ring), the
Caller ID message will
not appear.
•When the call is
received via a
telephone company
that does not offer
Caller ID service, the
caller’s phone number
and name does not
appear. (This includes
some international
calls.)
•When the call is via a
private branch
exchange (PBX), the
caller's phone number
and name may not
appear.
CALLER ID [50]
CALLER ID
Caller ID and CIDCW (Caller ID on Call Waiting)
•The number of calls
from the same Caller ID
appears next to the
received time. Once
you view the new
message, the number
will be cleared and
disappear.
•
icon appears next to
Time to indicate this is
a unread message.
Once you view the new
message, the icon
will disappear.
*
*
2) When you pick up the phone, the display changes to
(AutoTalk feature is set to on).
CALLER ID
note
You may receive any one of the following messages:
When invalid data is received; I n co m pl et e D a ta
When a private name is received; Pr i va te Na m e
When a private number is received; P ri v at e N u mb er
When a unknown name is received; Un kn o wn Na m e
When a unknown number is received; U nk n ow n N u mb er
Ta l k .
Data errors appear as "❚."
Viewing the Caller ID List
The Caller ID list stores information for incoming calls - even unanswered calls.
You can store up to 100 Caller ID messages and Phonebook locations (including
Speed Dials) for each handset and the base. You can view the Caller ID list through
the handset or base during a call or when the phone is in standby mode.
1) With the phone in standby mode, press cid/vol/ (or
cid/exit).
Or with the handset in talk mode, press the MENU soft
key. Use volume up/down to select C al l er ID , then
press the OK soft key.
[51] CALLER ID
%CNNGT+&
0GY
6QVCN
$#%-
&'.'6'
www.uniden.com
note
•During a call, don't
press end on the
handset or the call will
be disconnected.
•Once the Caller ID data
has been deleted, the
information cannot be
retrieved.
From Handset - press end (or the BACK soft key or talk/flash during a call).
From Base
- press cid/exit key or the BACK soft key.
Deleting a Caller ID Message
Deleting Information from the Caller ID List
1) When the phone is in standby mode, view the Caller ID information to be deleted
(see "Viewing the Caller ID List" on page 51).
2) From the base, press the DELETE soft key.
From the handset, press the EDIT soft key, and then use volume up/down to
select De l et e ? . Press the OK soft key. D e le te Ca l le r I D appears.
3) Press volume up/down to choose Ye s .
4) Press the OK soft key. You will hear a confirmation tone.
www.uniden.com
CALLER ID [52]
CALLER ID
The summary screen appears. The screen shows the number of new messages and
total messages.
2) To view the Caller ID messages in historical order (from new to old or from old to
new), repeatedly press volume down to scroll through the messages from the
latest to the earliest, or volume up to scroll back through the messages.
To view the Caller ID messages with alphabetical search, press the number key pad
(2-9 and 0) with the letter associated with the first letter of the desired message.
Once you view the Caller ID list with alphabetical search, you cannot switch
back to historical order (from new to old or from old to new) unless you
exit and re-enter the operation.
3) To finish the viewing operation:
note
You cannot make a call
from the Caller ID list if
your phone is connected
to a private branch
exchange (PBX).
1) When the phone is in standby mode, press cid/vol/
(cid/exit).
Press the DELETE soft key. D e le t e Al l ? appears.
2) Press volume up/down to choose
Ye s .
3) Press the OK soft key. You will hear a confirmation tone.
%CNNGT+&
0GY
6QVCN
$#%-
&'.'6'
&GNGVG#NN!
;GU
0Q
$#%-
$#%-
1-
Using the Caller ID Message List
Calling a party from the Caller ID list
From Standby mode
1) When the phone is in standby mode, select the Caller ID message (see "Viewing the
Caller ID List" on page 51).
2) Press talk/flash or speaker on the handset or speaker on the base. The
displayed phone number dials automatically.
From Talk mode
1) Press talk/flash or speaker on the handset or speaker on the base.
2) Select the Caller ID message you want to dial (see "Viewing the Caller ID List" on
page 51).
3) Press the DIAL soft key. The displayed phone number will be dialed.
[53] CALLER ID
www.uniden.com
CALLER ID
Deleting all Caller ID names/numbers
Storing Caller ID messages in the Phonebook
Messages shown in the Caller ID list can be stored in the phonebook. The phone
number and name of the party on the Caller ID list can be stored in memory.
1) When the phone is in standby mode, select the Caller ID message to be stored.
Then press the STORE soft key on the base or the EDIT soft key on the handset.
From the handset, then select ED I T? . S t or e/ E di t N a me appears. If the Caller ID
message is already stored in memory, you will hear a beep and Th i s da t a i s
a l re a dy st or e d! ! appears. The number will not be stored.
2) To complete the setting, follow the steps 3-8 in "Phonebook (Storing Phone
Numbers, Names, Distinctive Rings, and Speed Dial)" on pages 42-43.
www.uniden.com
note
•When a long distance call
has been set, "1" appears
in the display.
•If a call comes in via a
telephone system that
does not offer Caller ID
service, no information is
stored.
•If the Caller ID message
was received as a private/
unknown number, or the
message does not have
the number, you cannot
store the message in the
phonebook. If it was
received as private/
unknown name, the
message will be stored as
<No Name>.
•Even if the memory is full,
the message will be stored
in the phonebook.
However, the message will
be erased from the Caller
ID list.
CALLER ID [54]
CALLER ID
Long Distance calls and Area Code Setting/Cancellation
While the present Caller ID information is displayed, pressing */tone/< will place
or remove the prefix "1" in the display to set the call for a long distance call, or
pressing #/> will set or cancel an area code (see page 30).
•To activate features,
select C W O n/ CW D X
O n in the CIDCW
option. See page 30.
•You can also answer a
waiting call
immediately by
pressing talk/flash,
the first caller will be
placed on hold. To
return to the original
caller, press talk/flash
again.
•If you don't choose a
CWDX option within 30
seconds, the phone
returns to call.
•To return to the call,
press the BACK soft
key.
Your phone is pre-programmed with seven call waiting deluxe options. You may
select to ask the calling party to hold, send them a busy message, forward them to
your voice mail, or answer and drop the first caller. You may also select to
conference them into the current call or, at any time, choose to drop the first or
drop the last caller. You must subscribe to Call Waiting and Call Waiting Deluxe to
use these features. Not all features are available in all areas. Check with your local
telephone company for details.
1) From the base
When you receive a Call Waiting call, press the CWDX soft key for a list of
options.
From the handset
When you receive a Call Waiting call, press the MENU soft key.
Press volume up/down to select C a ll W ai t De lu x e , then the OK soft key for a list
of option.
2) Press volume up/down or the number keypad (1-7) to select an option.
For example:
press volume down 4 times
#UMVQ*QNF
6GNN$WU[
(QTYCTF%CNN
$#%-
$#%-
1-
press volume down 2 times
(QTYCTF%CNN
#PUYGT&TQR
%QPHGTGPEG
$#%-
$#%-
1-
%QPHGTGPEG
&TQR(KTUV
&TQR.CUV
$#%-
$#%-
1-
3) Press the OK soft key. A confirmation screen will appear, and the phone returns
to the call.
[55] CALLER ID
www.uniden.com
CALLER ID
note
Call Waiting Deluxe Features
The Integrated Telephone Answering Device
The phone has a built-in answering system that answers and records incoming calls.
You can also use your answering system to record a conversation, leave a voice
memo message, or to announce a special outgoing message to callers when you're
away from your phone.
Features
Digital Tapeless Recording
Up-to 12 minutes of Recording Time
Call Screening
Personal or pre-recorded Outgoing Messages
Voice Prompts for TAD (English, Spanish, or French)
Time and Day Announcement
Remote Message Retrieval
Toll Saver
Conversation Recording
Voice Memo
Message Alert On/Off
Retrieve TAD Messages using Handset
www.uniden.com
THE INTEGRATED ANSWERING DEVICE [56]
TH E INT E GR AT ED
ANSWERING DEVICE
•
•
•
•
•
•
•
•
•
•
•
•
note
•Position yourself as
near to the base as
possible and speak
clearly when recording
your outgoing
message.
•If you make an outside
call, or a call is
received on the base
during the operation,
the operation is
canceled.
1) To turn the answering system on, press
answer
on/off on the base when the phone is in standby
mode. /'55#)' and the number of messages stored
in memory appears on the sub-display. If the subdisplay flashes, then there are new messages
waiting for you.
2) To turn the answering system off, press
answer
#059'4
on/off on the base. 1(( appears on the subdisplay.
Setting your outgoing message (Greeting)
When you receive a call, the answering system automatically plays either the prerecorded message or your own greeting. To record your own greeting, or choose
between the two outgoing messages, refer to “Setting Menu Options”, “Answering
System Setup” on page 24.
The following message is pre-recorded: "Hello, no one is available to take your call.
Please leave a message after the tone."
Announce only feature
The announce only feature plays a pre-recorded outgoing message or your own personal
outgoing message, but it will not allow the caller to leave a message. To set announce
only, follow the steps on "Setting the Record Time" page 26. If you want to use your
[57] THE INTEGRATED ANSWERING DEVICE
www.uniden.com
TH E INT E GR AT ED
ANSWERING DEVICE
•When the answering
system is full, you will
hear “No Remaining
Time“ and (7.. appears
on the sub-display. You
should delete some
messages so that the
system can record new
messages.
Turning the Answering System On/Off
own greeting and you want to change your greeting to omit the prompt to leave a
message, refer to "Selecting Your Greeting (Base only)" on page 25.
The following message is pre-recorded:
"Hello, no one is available to take your call. Please call again."
Using the Answering Setup Menu
Menu Options
Base
Handset Menu Options
Base
Handset
Record Greeting

X
Record Time


Select Greeting

X
Message Alert


Security Code


Language


Ring Time


Call Screen


New Message LED
The new message LED on the handset flashes when you have new messages in your
answering system. The LED stops flashing when all new messages are played back.
www.uniden.com
THE INTEGRATED ANSWERING DEVICE [58]
TH E INT E GR AT ED
ANSWERING DEVICE
The Answering Setup menu allows you to set the following Answering System
functions through the handset or the base. For detailed instructions, see “Setting
Menu Options“, “Answering System Setup“ on page 24.
note
The time stamp will not
be heard until you have
set the time.
Using your Answering System
The message counter displays the number of messages
stored in memory. If the display flashes, then there
are new messages waiting for you. The answering
system is designed to play your new messages first.
After you play all your new messages, you can then
play your old messages.
Playing your messages
Repeating a message
1) Press
play/stop to review your messages. The number of stored messages is
announced.
2) To repeat the current message, press the |<< soft key after a few seconds of
beginning the message. To quickly scroll backwards through a message, press and
hold the |<< soft key. To repeat the previous message, press the |<< soft key
[59] THE INTEGRATED ANSWERING DEVICE
www.uniden.com
TH E INT E GR AT ED
ANSWERING DEVICE
1) When the base is in standby mode, press
play/stop.
The system announces the number of new and old messages while the message
counter displays only the number of new messages. The time and day that each
message was received is announced after the message is played. The message
counter will then display the number of current stored messages.
2) When all new messages have been played, you hear a confirmation tone and the
system announces "End of messages." The system returns to standby. After you
have reviewed your new messages, you can play your old messages by pressing
play/stop again. Once you have listened to a new message, it then becomes
an old message. The old messages will be played in the order in which they were
received.
within a few seconds (about 4 seconds during remote operation) after a message
begins playing. If you have several messages, press the |<< soft key repeatedly
until you return to the message you want to replay. If the current message is the
first new message, the system plays back from the beginning of the current
message (it does not go back into the old message group).
3) Press
play/stop at any time to stop reviewing messages and return to
standby.
The message counter shows the number of messages stored in memory.
1) Press
play/stop to review your messages. The number of stored messages is
announced.
2) Press the >>| soft key at anytime to skip to the next message.
Each time the >>| soft key is pressed, the system scans forward one message. If
you have several messages, press the >>| soft key repeatedly to find the message
you want to play. To quickly scroll through a message, press and hold the >>|
soft key. The system advances through the playback at double speed.
3) Press
play/stop at anytime to stop reviewing your messages and return to
standby. The message counter shows the number of messages stored in memory.
Deleting a message
To maintain
1) Press
2) Press the
to delete
maximum record time, delete the old messages.
play/stop to review your messages.
DELETE soft key or
delete message at anytime during the message
the message. You hear a confirmation tone and the message is deleted.
www.uniden.com
THE INTEGRATED ANSWERING DEVICE [60]
TH E INT E GR AT ED
ANSWERING DEVICE
Skipping a message
3) To delete all messages, press delete messege in standby mode. Press delete
messege again after the announcement "To delete all messages, press delete
again."
When you try to delete all messages without first listening to your new messages,
you hear several short beeps followed by an announcement "Please playback all
messages." This protects you from accidentally erasing messages you have not yet
reviewed.
Voice memo
The voice memo function allows the user to record messages (more than 2 seconds
and less than 4 minutes).
1) In stand by mode, press the RECORD soft key on the base.
2) Press the START soft key.
3) Start your recording after the announcement "Record Memo Message" and a
confirmation tone.
4) When you have finished, press the STOP soft key to stop recording. The system
returns to standby.
[61] THE INTEGRATED ANSWERING DEVICE
www.uniden.com
TH E INT E GR AT ED
ANSWERING DEVICE
Important:
When you press delete messege, you are permanently deleting the message. Once
deleted, the message cannot be replayed or retrieved.
Recording a conversation
You can record a conversation from the handset or the base (more than 2 seconds
and less than 10 minutes).
1) During a conversation, press the MENU soft key.
2) Press volume up/down to select Ca ll Re c or d , and then press the OK soft key.
R e co r di n g a C al l appears on the display.
A confirmation tone, that can be heard by both parties, sounds during recording.
3) To stop recording:
Screening a call
From the base
To screen an incoming call, use the following steps:
1) After the answering system answers, the base speaker will let you hear the calls
as the machine records the message. To adjust the volume, press volume/ or
volume/ . If you set the answering system to off, you cannot screen a call.
www.uniden.com
•Every state has
different regulations
governing the
recording of
conversations over the
telephone. Make sure
to check your local,
state and federal laws
before using this
product to record any
telephone
conversation in order
to determine that your
use is in compliance
with such laws or
guidelines.
•To active this feature,
you must turn the Call
Screen feature on. See
“Answering System
Setup“, “Setting the
Call Screen“ on
page 28.
•If you press the
SCREEN soft key while
another handset is
screening a call, you
will hear a beep and
you can not screen a
call.
THE INTEGRATED ANSWERING DEVICE [62]
TH E INT E GR AT ED
ANSWERING DEVICE
From Handset - press the MENU soft key and volume up/down to select Ca ll R eco rd .
You will hear a confirmation tone.
From Base
- press play/stop. Or press the MENU soft key and volume/ or
volume/ to select C al l R ec o rd . You will hear a confirmation tone.
note
2)
a)To mute the Call Screen, press the MUTE soft key or
play/stop. To cancel
muting, press the SCREEN soft key.
b)To answer the call, press speaker or pick up the handset from the base (when
AutoTalk is set to on).
Remote Operation
You can check, play, or delete messages, even record a new greeting message from a
remote location (when you are away from home, or from another room using a
handset). Additionally, you can turn on or off your answering system remotely.
Remote access away from home
You can operate your answering system from a remote location using any touchtone telephone.
1) Call your telephone number and wait for the system to answer. If the answering
system is off, it will answer after about 10 rings and sounds a series of beeps.
2) During the greeting message (or a series of beeps when the answering system is
off), press 0 and enter your PIN code within 2 seconds (see "Setting a PIN Code"
on page 25).
[63] THE INTEGRATED ANSWERING DEVICE
www.uniden.com
TH E INT E GR AT ED
ANSWERING DEVICE
From the handset
Press the SCREEN soft key when the system is answering. To mute the Call Screen,
press the MUTE soft key. If the handset is away from the base, press talk/flash,
speaker or any number key, */tone/<, or #/> (when AutoTalk is set to on). The
answering system will disconnect automatically.
3) The answering system announces the current time and the number of messages
stored in memory. You hear "To play incoming messages, press zero-two. For
help, press one-zero." You will hear a beep.
4) Enter a command within 15 seconds, each command there after must be entered
within 2 seconds. You may select a command from the following chart:
Command
Function
Command
Function
www.uniden.com
•Time stamp will not be
heard until you have set
the time. See "Setting
Day and Time" on
page 29.
•The system will only
playback messages for
four minutes and then
it returns to the
command waiting mode.
To continue playing
your messages, press 0
then 2 again within 15
seconds.
•If you enter an
incorrect PIN code three
times, you will hear a
beep and the system
will return to standby.
•During the remote
operation, Li n e
Remote appears on the
display.
•If the answering system
is recording an
incoming message, the
recording operation is
canceled when you start
remote operation.
•For your convenience a
remote operation card is
provided for you to use
while away from home
(refer to page 88).
THE INTEGRATED ANSWERING DEVICE [64]
TH E INT E GR AT ED
ANSWERING DEVICE
0 then 1 Repeat a Message*
0 then 6 Answering System On
0 then 2 Playing incoming Messages
0 then 7 Memo Record/Stop**
0 then 3 Skipping a Message
0 then 8 Greeting Message Record/Stop**
Deleting
a
Message
0 then 4
0 then 9 Answer System Off
0 then 5 Stop Operation
1 then 0 Help
* For the Repeat a Message function, press 0 then 1 within about four seconds to
repeat the previous message, or press 0 then 1 after about four seconds to repeat
the current message.
** For the Memo Record and Greeting Message Record functions, the first time you
enter the corresponding command, the phone starts recording. If you want to
stop the recording, press 0 then 7, 8 or 5.
5) After the command has finished, you hear intermittent beeps indicating that the
system is in the command waiting mode. You may enter another command at this
time from the chart above.
note
6) When you are finished, hang up to exit the system. The answering system
automatically returns to standby.
Remote access with the handset
note
•When the answering
system is full, (7..
appears on the base.
You should delete
some messages so that
the system can record
new messages. (Refer
to "Deleting a
message" on page 60.)
• If you press end before the answering system answers, the phone will return to standby.
• When the answering system does not answer within 6 seconds, you hear a beep and the
phone will return to standby.
• When you receive a call, the remote operation is canceled.
• You can change the handset volume during a remote operation.
• During the remote operation Re m ot e A ns w er i ng M ac h in e o pe r at i on appears on the
base.
• If you have new messages and old messages, after you have reviewed your new
messages, you can play your old messages by pressing 2 again.
3) Enter a command within 30 seconds. Select a command from the following chart:
[65] THE INTEGRATED ANSWERING DEVICE
www.uniden.com
TH E INT E GR AT ED
ANSWERING DEVICE
•Time stamp will not be
heard until you have
set the time.
You can operate your answering system from another room using a handset.
1) When the phone is in standby mode, press
on the handset. R em o te
A n sw er i ng M ac h in e o pe r at i on appears on the handset display. The answering
system announces the current time and the number of messages stored in the
memory. Messages will be played in the order in which they were received. The
time and day that each message was received is announced after the message is
played.
2) You hear "To play incoming messages, press two. For help, press zero."
You will hear a beep.
Remote Key Function
|<</1
Repeat a Message*
/2
>>|/3
∅/4
†/5
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
6
7
8
9
0
Answering System On
Greeting Message Record/Stop**
Answer System Off
Help Guidance
•The voice memo
messages are recorded
as an incoming
messages.
•When the answering
system is full, (7..
appears on the display,
and recording is
terminated.
•If an outside call is
received during the
operation, the
operation is canceled.
•You cannot record
intercom
conversations.
THE INTEGRATED ANSWERING DEVICE [66]
TH E INT E GR AT ED
ANSWERING DEVICE
* For the Repeat a Message function, press 1 within about four seconds to repeat
the previous message, or press 1 after about four seconds to repeat the current
message.
** For the Memo Record and Greeting Message Record functions, the first time you
enter the corresponding command, the phone starts recording. If you want to
stop the recording, press 7, 8 or 5.
4) After the command has finished, you will hear intermittent beeps indicating that
the system is waiting for a command. You may enter another command at this
time from the chart above.
5) When you are finished, press end to exit the system.
www.uniden.com
note
Memo Record/Stop**
note
•If you have any trouble
with your phone, visit
our web site at
www.uniden.com or
call our Customer
Hotline at 1- 800-2971023 (Mon-Fri 7 am to
7pm, Sat/ Sun 9 am to
5pm, CST). (The
Customer Service
Hotline is closed on
holidays.)
•Charge the handset
battery pack for at
least 15-20 hours
before using your new
cordless telephone for
the first time.
Expanding Your Phone
10 Handset Expandability
Your phone supports up to 10 handsets,
including any handsets supplied with your
phone. You can now place a fully-featured
cordless handset anywhere AC power is
available to connect the handset charger.
Up to 2 handsets can be used in DirectLink
Mode or on an intercom call without interfering with incoming calls. It is possible
to have a 4-way conference among the base, 2 handsets, and one outside line.
All of the handsets ring when a call is received.
Backwards/Forwards Compatibility
Your phone is compatible with other Uniden 5.8GHz Digital
Expandable Handsets. Compatible models include the TCX400,
TCX440, and ELX500. (Please check www.uniden.com for an
updated list of expansion handsets compatible with this
series.)
www.uniden.com
E X PA N D I N G Y O U R
PHONE
[67] EXPANDING YOUR PHONE
Connecting the Charger
note
1) Connect the AC adapter to the DC IN 9V jack
and to a standard 120V AC wall outlet.
2) Set the charger on a desk or tabletop, and
place the handset in the charger with the
keypad facing forward. (See " B. Install.... the
rechargeable battery pack into the handset,
and charge for at least 15-20 hours before
using" on page 10.)
•An extra handset can
be registered when the
main base is in
standby mode.
•If a handset has ever
been registered to a
different base, you
must de-register the
handset before you can
register it to the new
base (see page 32).
Register the Handset
If you purchase an expansion handset, you need to register the handset before use.
Only one handset can be registered at a time.
Register the expansion handset to main base
Before an expansion handset is registered, the battery pack MUST be charged for 15
hours.
www.uniden.com
EXPANDING YOUR PHONE [68]
E X PA N D I N G Y O U R P H O N E
Handsets supplied with the phone are registered to the base by the factory. When
charged, pre-registered handsets display a handset ID number. Handsets that have
not been registered display M od el s v a ry ! C h ar ge ha n ds e t on th e b a se fo r
r e gi s tr a ti on or re f er e t o O wn e r' Ma nu a l . When you register an extra handset to
the base, the handset ID will be assigned.
To register a TCX805 handset, simply place it in the main base.
While the handset is registering, H a nd se t R e gi s te ri n g will appear in the LCD.
When R eg i st r at i on co mp l et e . is displayed, the handset has been registered to
the base. If Re gi s tr a ti o n fa i le d . appears, please try these steps again.
To
1)
2)
3)
register a ELX500, TCX440, or TCX400 handset, follow the steps below:
Disconnect the AC adapter from the main base.
While pressing down flash/find hs, reconnect the AC adapter.
On the handset, press and hold # until you hear a beep.
While the handset is registering, H a nd se t R e gi s te r in g will appear in the LCD. When
is displayed, the handset has been registered to the base. If
R e gi s tr at i on fa i le d. appears, please try these steps again.
Reg istration complete.
www.uniden.com
E X PA N D I N G Y O U R
PHONE
[69] EXPANDING YOUR PHONE
Using DirectLink Mode
note
To use this feature, you must enter the handsets
into DirectLink mode first.
To enter DirectLink mode, see page 17.
Handsets can be in
DirectLink mode while
other handsets are in
use.
DirectLink call
1) When the phone is in the DirectLink standby
mode, press the DirectLink soft key (example of
DirectLink from handset #1).
570#
*CPFUGV
&KTGEV.KPM/QFG
2) Select the handset to which you wish to DirectLink
with by pressing the number keys (0-9). Your handset
will then page the other handset.
6Q&KTGEV.KPM
CJCPFUGV
RTGUU=?
%#0%'.
&KTGEV.KPM
$#%-
3) On the receiving handset, press talk/flash, the
ANSWER soft key, or if Any Key Answer is on, press any
number key, */tone/<, or #/>.
&KTGEV.KPM
*CPFUGV
'0&
www.uniden.com
EXPANDING YOUR PHONE [70]
E X PA N D I N G Y O U R P H O N E
4) When you finish your conversation, press end or the
END soft key on either handset. To cancel DirectLink mode (and return to normal
standby), return the handset to the cradle or press the CANCEL soft key, and
then press the OK soft key.
note
Intercom/Call Transfer Feature
Intercom and Call Transfer features are available for your phone.
Intercom
•If the party is busy or
out of range, the
handset returns to
standby mode.
•If any you receive an
outside/intercom call
or page while selecting
the other handset (or
the base), the
operation will be
canceled.
•If the party does not
answer within one
minute, the operation
is canceled.
From handset to handset or handset to the base
1) In standby mode, press intcom/hold.
2) Select the base or the handset you want to talk with
within 30 seconds. To select the handset (or the
base), press volume up/down, and then press the OK
soft key. If you select Al l , all other handsets and the
base will be paged. An intercom tone sounds.
6QKPVGTEQO
*CPFUGV
*CPFUGV
1-
To cancel intercom, press the CANCEL soft key.
[71] EXPANDING YOUR PHONE
www.uniden.com
E X PA N D I N G Y O U R
PHONE
3) To answer the page on a handset, press talk/flash,
+PVGTEQO
intcom/hold, or the ANSWER soft key. If Any Key
*CPFUGV
Answer is enabled, pressing any number key, */tone/<,
#059'4
or #/> will answer the page. If AutoTalk is enabled, you
can answer the page by simply picking up the handset.
To answer a page from the base, press intercom/hold, speaker, or the ANSWER
soft key.
4) To hang up the intercom call, press end or the END soft key on either handset (or
the END soft key or intercom/hold on the base).
From the base to a handset
1) In standby mode, press intercom/hold on the base.
2) Select the handset you want to talk with within 30 seconds. To select the
handset, press volume/ or volume/ , and then press the OK soft key. If
you select A ll , all handsets will be paged. An intercom tone sounds. To cancel
intercom, press intercom/hold or the CANCEL soft key.
3) Follow the steps 3-4 under “From handset to handset or handset to the base“ on
page 71.
Call Transfer Feature
www.uniden.com
EXPANDING YOUR PHONE [72]
E X PA N D I N G Y O U R P H O N E
From handset to handset or to the base
1) During a call, press intcom/hold on the handset.
2) Select a handset or the base to transfer the call to
*QNFVQVTCPUHGT
within 10 seconds. To select the handset (or the base), * C P F U G V press volume up/down, and then press the OK soft key. * C P F U G V 1If you select A l l , all other handsets and the base will
be paged.
The call will automatically be placed on hold, and an intercom tone sounds.
To cancel the transfer, press talk/flash, the CANCEL soft key or speaker on the
initiating handset.
3) To answer the page on a handset, press talk/flash, intcom/hold, or the ANSWER
soft key. If Any Key Answer is enabled, pressing any number key,
*/tone/<, or #/> will answer the page. If AutoTalk is enabled, you can answer
the page by simply picking up the handset. To answer a page from the base, press
intercom/hold, speaker, or the ANSWER soft key.
4) To speak to the caller, press talk/flash on the receiving handset or speaker on
the base.
From the base to a handset
1) During a call, press intercom/hold on the base. The call will automatically be
placed on hold.
2) Select the handset you want to talk with within 10 seconds. To select the
handset, press
volume/ or
volume/ and then press the OK soft key. If
you select A ll , all handsets will be paged. An intercom tone sounds. To cancel
the transfer, press intercom/hold, speaker or the CANCEL soft key on the base.
3) To answer the page on a handset, press talk/flash, intercom/hold, or the
ANSWER soft key. If Any Key Answer is enabled, pressing any number key,
*/tone/<, or #/> will answer the page. If AutoTalk is enabled, you can answer
the page by simply picking up the handset.
4) To speak to the caller, press talk/flash on the receiving handset.
www.uniden.com
E X PA N D I N G Y O U R P H O N E
[73] EXPANDING YOUR PHONE
The digital security code is an identification code used to connect the handset and
the base unit. Normally, setting the code is not necessary. In the rare situation that
you suspect another cordless telephone is using the same security code, you can
change the code. To change the digital security code:
1. De-register all the handsets you have (see “De-register the handset“ on page 32).
2. Register the handsets by following the steps under "Register the Handset" on
page 68.
Find Handset
To locate the handset, press flash/find hs on the base
when the phone is in standby mode. All registered
handsets beep for 60 seconds, and Pa g in g appears on
the handset display. To cancel paging, press any key
on the handset or flash/find hs on the base.
www.uniden.com
ADDITIONAL INFORMATION [74]
ADDITIONAL
I N F O R M AT I O N
Changing the Digital Security Code
ADDITIONAL
I N F O R M AT I O N
Installing the Beltclip
To attach the beltclip
Insert the beltclip into the holes on each side of the
handset. Press down until it clicks.
To remove the beltclip
Pull either side of the beltclip to release the tabs from
the holes.
Headset Installation
Your phone may be used with an optional headset. To use
this feature, insert the headset plug into the headset jack.
Your phone is ready for hands-free conversations.
(Headset may be purchased by calling the Uniden Parts
Department or visiting the web site. See back page.)
[75] ADDITIONAL INFORMATION
www.uniden.com
Battery replacement and handling
When the operating time becomes short, even after a battery is recharged, please
replace the battery. With normal usage, your battery should last about one year.
Please contact your place of purchase or the Uniden Parts Department for a
replacement battery.
Warning
To avoid the risk of personal injury or property damage from fire or electrical shock,
only use the Uniden battery model and Uniden adapter model specifically
designated for this product.
Power Failure
During the period that the power is off, you will not be able to make or receive calls
with the telephone.
Caution
•
•
•
•
Use only the specified Uniden battery pack (BT-446).
Do not remove the batteries from the handset to charge them.
Never throw the battery into a fire, disassemble them, or heat them.
Do not remove or damage the battery casing.
Maintenance
To maintain a good charge, it is important to clean the charging contacts on both
the handset and the base unit once a month. Using water only, dampen a cloth to
clean the charging contacts. Then make sure to go back over the charging contacts
with a dry cloth.
Caution
Do not use paint thinner, benzene, alcohol, or other chemical products.
Doing so may discolor the surface of the telephone and damage the finish.
www.uniden.com
ADDITIONAL INFORMATION [76]
ADDITIONAL
I N F O R M AT I O N
Note on Power Sources
The phone complies with FCC Parts 15 and 68. Operating temperature:
0 °C to +50 °C (+32 °F to +122 °F)
AC Adapter Information
AC Adapter part number: AD-830 for the base
Input Voltage: 120 AC 60Hz
Output Voltage: 9V DC 400mA
AD-0005 for the charger (TRU8885-2/3 only)
120V AC 60Hz
9V DC 210mA
Battery Information
Battery part number: BT-446
Capacity: 800mAh, 3.6V
• To avoid damage to the phone use only Uniden AD-830 and BT-446 with your phone.
• If the handset is left off of the base, the actual Talk mode duration will be reduced
respective to the amount of time the handset is off the base.
Recharge your phone on a regular basis by returning the handset to the base after
each phone call. When the operating time becomes short even after the battery is
recharged, please replace the battery. With normal usage, the battery should last
about one year.
A replacement Uniden adapter or battery may be purchased by contacting the
Uniden Parts Department (see back page).
Specifications, features, and availability of optional accessories are all subject to
change without prior notice.
[77] ADDITIONAL INFORMATION
www.uniden.com
ADDITIONAL
I N F O R M AT I O N
General Information
Troubleshooting
If your phone is not performing to your expectations, please try these simple steps first.
Symptom
Suggestion
The audio sounds weak.
• Move the handset and/or base away from metal objects or appliances and try again.
• Make sure that you are not too far from the base.
Can't make or receive calls.
• Check both ends of the base telephone line cord.
• Make sure the AC adapter is plugged into the base and wall outlet.
• Disconnect the AC adapter for a few minutes, and then reconnect it.
• De-register the handset (see "De-register the Handset" on page 32) and register the handset
(see "Register the Handset" on page 68).
• Make sure that you are not too far from the base.
• Make sure the line is not in use.
• If an outside call is already established, you can not make another outside call.
The handset doesn't ring or
receive a page.
• Charge the batteries in the handset for 15-20 hours by placing the handset on the base or
charging cradle.
• Make sure that you are not too far from the base.
• De-register the handset (see "De-register the Handset" on page 32) and register the handset
(see "Register the Handset" on page 68).
Un a va i la b le appears in
the display.
www.uniden.com
• Make sure that another handset(s) or the base is not in use, and try the phone again.
• Make sure that you are not too far from the base.
TROUBLESHOOTING [78]
TROUBLESHOOTING
• Make sure the AC adapter is plugged into the base or the charger (if you have more than one
handset) and wall outlet.
The charge LED won't illuminate
• Make sure the handset is properly seated in the cradle.
when the handset is placed in
• Make sure the charging contacts on the handset and the base or the charger (if you have more
the cradle.
than one handset) are clean.
Symptom
Suggestion
Severe noise interference.
• Keep the handset away from microwave ovens, computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical
appliances.
• Move to another location or turn off the source of interference.
The Caller ID does not display.
• The handset was picked up before the second ring.
• The call was placed through a switchboard.
• Call your local telephone company to verify your Caller ID service is current. There may be a
problem with your Caller ID service.
The handset doesn't
communicate with other
handsets.
• De-register the handset (see "De-register the Handset" on page 32) and register the handset
(see "Register the Handset" on page 68).
• Make sure that you have registered all handsets.
An extra handset can't join
the conversation.
• Make sure there are not 2 handsets already using the 3-way conference feature.
The handset or the base can't
join the conversation
• Make sure that another handset or base is in privacy mode.
The answering system does
not work.
• Make sure the base unit is plugged in.
• Make sure that the answering system is turned on.
• Make sure that the message record time is not set to Announce only (see page 26).
Messages are incomplete.
• The incoming messages may be too long. Remind callers to leave a brief message.
• The memory may be full. Delete some or all of the saved messages.
After a power failure, the
outgoing message is deleted.
• Record your greeting again. The default message should remain.
[79] TROUBLESHOOTING
www.uniden.com
TROUBLESHOOTING
• Charge the battery pack for 15-20 hours.
You cannot register the handset
• De-register the handset (see "De-register the Handset" on page 32) and register the handset
at the base.
(see "Register the Handset" on page 68).
Symptom
Suggestion
No sound on the base unit
speaker during call monitoring
or message playback.
• Adjust the speaker volume on the base unit.
• Make sure the call screen feature is set to on.
Cannot access remote call-in
features from another touchtone phone.
• Make sure you are using the correct PIN number.
• Make sure that the touch-tone phone you're using can transmit the tone for at least two
seconds. If it cannot, you may have to use another phone to access your phone.
Time stamp cannot be heard.
• Make sure you have set the time (see "Setting Day and Time" on page 29).
If you still have a problem.
• Call our customer hotline at 1-800-297-1023.
TROUBLESHOOTING
www.uniden.com
TROUBLESHOOTING [80]
Liquid Damage
Moisture and liquid may damage your cordless phone. Follow the steps below if your phone gets wet:
Case
[81] TROUBLESHOOTING
Action
Wipe off the liquid, and use as normal.
Handset:
1) Remove the battery cover and leave it off for ventilation.
2) Disconnect the battery pack. Leave the battery cover off and the battery pack
disconnected for at least 3 days.
3) Once the handset is completely dry, reconnect the battery pack and the battery
cover.
4) Recharge the handset's battery pack for 20 hours before using.
Base:
1) Disconnect the AC adapter from the base, cutting off electrical power.
2) Disconnect the telephone cord from the base.
3) Let dry for at least 3 days.
IMPORTANT: You must unplug the telephone line while recharging the battery
packs to avoid charge interruption.
CAUTION: DO NOT use a microwave oven to speed up the drying process. This will
cause permanent damage to the handset, base and the microwave oven.
After following these steps, if your cordless telephone does not work, please call
our Customer Service Hotline at 1-800-297-1023.
www.uniden.com
TROUBLESHOOTING
If the exterior plastic housing on the handset or
base is exposed to moisture or liquid.
If moisture or liquid has entered the plastic housing
(i.e. liquid can be heard in the phone or liquid has
entered the handset battery compartment or vent
openings on the base).
Precautions!
Before you read anything else, please observe the following:
Warning!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage to the
unit, DO NOT expose this unit to rain or moisture.
Rechargeable Nickel-Metal-Hydride Battery Warning
• This equipment contains a rechargeable Nickel-Metal-Hydride battery.
• Nickel is a chemical known to state of California to cause cancer.
• The rechargeable Nickel-Metal-Hydride battery contained in this
equipment may explode if disposed of in a fire.
• Do not short-circuit the battery.
• Do not charge the rechargeable Nickel-Metal-Hydride battery used in
this equipment in any charger other than the one designed to charge
this battery as specified in the owner's manual. Using another charger
may damage the battery or cause the battery to explode.
Rechargeable Nickel-Metal-Hydride
Batteries Must Be Recycled or
Disposed of Properly
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Uniden works to reduce lead content in our PVC coated cords in our
products and accessories.
Warning!
The cords on this product and/or accessories contain lead, a chemical
known to the State of California to cause birth defects or other
reproductive harm. Wash hands after handling.
4. Use only the power cord and batteries indicated in this manual. Do
not dispose of batteries in a fire. They may explode. Check with local
codes for possible battery disposal instructions.
5. Do not disassemble any component of this product.
SAVE THESE INSTRUCTIONS
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions. Do not open or mutilate the
battery, and disconnect the battery before shipping this product.
The FCC Wants You To Know
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this equipment is a
label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided to
the telephone company.
An applicable Universal Service Order Codes (USOC) certification for the
jacks used in this equipment is provided (i.e., RJ11C) in the packaging
with each piece of approved terminal equipment.
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68 rules
and requirements adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See
installation instructions for details.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company. For
products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a decimal point (e.g., 03 is a REN
of 0.3). For earlier products, the REN is separately shown on the label.
1. Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
2. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the
leak.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide advance
notice in order for you to make necessary modifications to maintain
uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery replacement
section); otherwise do not substitute or repair any parts of the device
except as specified in this manual.
www.uniden.com
Should you experience trouble with this equipment, please contact
Uniden customer service at 800-297-1023. If the equipment is causing
harm to the telephone network, the telephone company may request that
you disconnect the equipment until the problem is resolved.
NOTICE: According to telephone company reports, AC electrical surges,
typically resulting from lightning strikes, are very destructive to
telephone equipment connected to AC power sources. To minimize
damage from these types of surges, a surge arrestor is recommended.
Changes or modifications to this product not expressly approved by
Uniden, or operation of this product in any way other than as detailed by
the owner's manual, could void your authority to operate this product.
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications, may not be ensured when using this phone.
To insure the safety of users, the FCC has established criteria for the
amount of radio frequency energy various products may produce
depending on their intended usage. This product has been tested and
found to comply with the FCC's exposure criteria. For body worn
operation, the FCC RF exposure guidelines were also met when used with
the Uniden accessories supplied or designed for this product. Use of
other accessories may not ensure compliance with FCC RF exposure
guidelines and should be avoided.
Radio Interference
Radio interference may occasionally cause buzzing and humming in your
cordless handset, or clicking noises in the base. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition,
we recommend that the base not be plugged into a circuit that also
powers a major appliance because of the potential for interference. Be
certain that the antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of interference.
If you cannot eliminate this type of interference, you need to change to
a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther away
from the TV or VCR will often reduce or eliminate the interference.
PRECAUTIONS & WARRANTY [82]
PRECAUTIONS &
WARRANT Y
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn't practical, the
telephone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
Important Safety Instructions
Connection to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or corporation
commission for information.
This equipment is hearing aid compatible.
Cordless Telephone Privacy
Cordless telephones are radio devices. Communications between the
handset and base of your cordless telephone are accomplished by means
of radio waves which are broadcast over the open airways.
Because of the inherent physical properties of radio waves, your
communications can be received by radio receiving devices other than
your own cordless telephone unit. Consequently, any communications
using your cordless telephone may not be private.
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF
WARRANTY: Uniden warrants, for one year, to the original retail owner,
this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This warranty
is void outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in the owner's manual you are certain that the
Product is defective, pack the Product carefully (preferably in its original
packaging). Disconnect the battery from the Product and separately
secure the battery in its own separate packaging within the shipping
carton. The Product should include all parts and accessories originally
packaged with the Product. Include evidence of original purchase and a
note describing the defect that has caused you to return it. The Product
should be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
[83] PRECAUTIONS & WARRANTY
www.uniden.com
PRECAUTIONS &
WAR R A N T Y
WARRANTY DURATION: This warranty to the original user shall terminate
and be of no further effect 12 months after the date of original retail
sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used as
part of any conversion kits, subassemblies, or any configurations not
sold by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with
equipment or parts or as part of any system not manufactured by Uniden,
or (F) installed or programmed by anyone other than as detailed by the
owner's manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform
to this warranty at any time while this warranty is in effect, warrantor
will either, at its option, repair or replace the defective unit and return it
to you without charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its
option, may replace the unit with a new or refurbished unit. THE LIMITED
WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or
limitation of incidental or consequential damages so the above limitation
or exclusion may not apply to you.
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies
that registration was performed based on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The
REN assigned to each terminal equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed five.
RADIO EQUIPMENT
The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were
met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device. "Privacy of
communications may not be ensured when using this telephone".
www.uniden.com
I.C. NOTICE [84]
I.C. NOTICE
I.C. Notice
Memory List
Name
Name
Phone No.
[85] MEMORY LIST
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Phone No.
Name
Phone No.
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
www.uniden.com
MEMORY LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Index
0-9
20 ring options . . . . . . . . . . . . .
3 or 4-Way Conferencing . . . . . . .
A
Animation screen . . . . . . . . . . . .
Announce only feature . . . . . . . .
Answering system
Deleting a message . . . . . . . . .
Playing your messages . . . . . . .
Recording a conversation . . . . .
Remote access . . . . . . . . . . . .
Repeating a message . . . . . . . .
Skipping a message . . . . . . . . .
Turning On/Off . . . . . . . . . . . .
Anykey Answer . . . . . . . . . . . . . .
Area Code . . . . . . . . . . . . . . . . .
AutoTalk . . . . . . . . . . . . . . . . . .
B
Banner . . . . . . . . . . . . . . . . . . .
Battery
Preparing and charging . . . . . .
Replacement and handling . . . .
Beltclip . . . . . . . . . . . . . . . . . .
C
Call screen . . . . . . . . . . . . . . . .
Call transfer feature . . . . . . . . . .
Caller ID
Call Waiting . . . . . . . . . . . . . .
Caller ID services . . . . . . . . . .
Calling . . . . . . . . . . . . . . . . .
www.uniden.com
19
40
24
57
60
59
62
63
59
60
57
21
30
21
22
10
76
75
28
72
34
50
53
CIDCW . . . . . . . . . . . . . . . . . . 50
CWDX . . . . . . . . . . . . . . . . . . . 55
Deleting . . . . . . . . . . . . . . . . . 52
Setting . . . . . . . . . . . . . . . . . . 30
Storing . . . . . . . . . . . . . . . . . . 54
Viewing . . . . . . . . . . . . . . . . . 51
Chain dialing . . . . . . . . . . . . . . . 43
Clock . . . . . . . . . . . . . . . . . . . . 29
Contrast . . . . . . . . . . . . . . . . . . 23
Copying phonebook . . . . . . . . . . . 49
D
Deluxe Call Waiting Features . . . . . 55
De-register the handset . . . . . . . . 32
Dial mode . . . . . . . . . . . . . . . . . 31
Digital security code . . . . . . . . . . 74
DirectLink . . . . . . . . . . . . . . . . . 70
Distinctive ringer . . . . . . . . . . . . 20
E
Earpiece volume . . . . . . . . . . . . . 37
Expanding your phone . . . . . . . . . 67
G
General information . . . . . . . . . . . 77
H
hands-free conversation . . . . . . . . 33
Headset installation . . . . . . . . . . 75
I
I.C. notice . . . . . . . . . . . . . . . . . 84
Important safety instructions . . . . 82
Intercom . . . . . . . . . . . . . . . . . . 71
K
Key touch tone . . . . . . . . . . . . . . 23
L
Language . . . . . . . . . . . . . . . . . .22
Liquid damage . . . . . . . . . . . . . . .81
M
Maintenance . . . . . . . . . . . . . . . .76
Making a call . . . . . . . . . . . . . . .33
Message alert . . . . . . . . . . . . . . .27
Mute . . . . . . . . . . . . . . . . . . . . .38
N
New message LED . . . . . . . . . . . .58
O
Outgoing message . . . . . . . . . 24, 57
P
Phonebook
Editing . . . . . . . . . . . . . . . . . .48
Erasing . . . . . . . . . . . . . . . . . .48
Making calls . . . . . . . . . . . . . .47
Storing . . . . . . . . . . . . . . . . . .42
Viewing . . . . . . . . . . . . . . . . .46
Precautions . . . . . . . . . . . . . . . . .82
Privacy Mode . . . . . . . . . . . . . . .40
R
Receiving a call . . . . . . . . . . . . . .33
Redialing a call . . . . . . . . . . . . . .35
Register the handset . . . . . . . . . .68
Remote . . . . . . . . . . . . . . . . . . .65
Remote access
away from home . . . . . . . . . . . .63
from your handset . . . . . . . . . .65
Ringer
Adjusting . . . . . . . . . . . . . . . .37
Do not disturb . . . . . . . . . . . . .37
INDEX
[86]
mute . . . . . . . . . . . . . . . . . . . 38
Room/baby monitor . . . . . . . . . . 18
S
Setting up
base unit . . . . . . . . . . . . . . . . 12
extra handset . . . . . . . . . . . . . 68
Handset . . . . . . . . . . . . . . . . . 19
Menu options . . . . . . . . . . . . . 16
Soft Key . . . . . . . . . . . . . . . . . . . 8
Speed dialing . . . . . . . . . . . . . . 47
T
Transferring a call . . . . . . . . . . . 72
V
Voice memo . . . . . . . . . . . . . . . . 61
W
Warranty . . . . . . . . . . . . . . . . . . 83
[87] INDEX
www.uniden.com
Remote Operation Card
CUT
CUT
REMOTE OPERATION CARD
REMOTE OPERATION CARD
Turn on the answering
system remotely
Remote access away from
home
Turn on the answering
system remotely
1. Call your phone number from a
touch-tone phone.
2. During the outgoing message,
press 0 and enter your PIN code.
The answering system announces
the number of messages stored in
memory and the voice prompts.
3. To quit, hang up the phone.
1. Call your phone and let it ring
10 times until you hear a beep.
2. Press 0 and then enter your
PIN code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
1. Call your phone number from a
touch-tone phone.
2. During the outgoing message,
press 0 and enter your PIN code.
The answering system announces
the number of messages stored in
memory and the voice prompts.
3. To quit, hang up the phone.
1. Call your phone and let it ring
10 times until you hear a beep.
2. Press 0 and then enter your
PIN code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
CUT
CUT
REMOTE OPERATION CARD
REMOTE OPERATION CARD
Remote access away from
home
Turn on the answering
system remotely
Remote access away from
home
Turn on the answering
system remotely
1. Call your phone number from a
touch-tone phone.
2. During the outgoing message,
press 0 and enter your PIN code.
The answering system announces
the number of messages stored in
memory and the voice prompts.
3. To quit, hang up the phone.
1. Call your phone and let it ring
10 times until you hear a beep.
2. Press 0 and then enter your
PIN code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
1. Call your phone number from a
touch-tone phone.
2. During the outgoing message,
press 0 and enter your PIN code.
The answering system announces
the number of messages stored in
memory and the voice prompts.
3. To quit, hang up the phone.
1. Call your phone and let it ring
10 times until you hear a beep.
2. Press 0 and then enter your
PIN code.
3. Press 0 then 5 to stop
the announcement.
4. Press 0 then 6 to turn the
answering system on.
www.uniden.com
REMOTE OPERATION CARD [88]
REMOTE
OPERATION CARD
Remote access away from
home
CUT
CUT
Key
CUT
Task
Repeat a Message
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
Answering System On
Memo Record/Stop
Greeting Message Record/Stop
Answer System Off
Help Guidance
[89] REMOTE OPERATION CARD
Task
Repeat a Message
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
Answering System On
Memo Record/Stop
Greeting Message Record/Stop
Answer System Off
Help Guidance
Key
CUT
Key
Task
Repeat a Message
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
Answering System On
Memo Record/Stop
Greeting Message Record/Stop
Answer System Off
Help Guidance
Key
www.uniden.com
R E M OT E OP ERAT ION
Task
Repeat a Message
Playing incoming Messages
Skipping a Message
Deleting a Message
Stop Operation
Answering System On
Memo Record/Stop
Greeting Message Record/Stop
Answer System Off
Help Guidance
Main Menu Flow Chart
•From standby mode
•Base
570#
4QQO/QPKVQT
$CUG5GVWR
#PUY5GVWR
MENU
0GY%+&
4'&+#.
/'07
4'%14&
$#%-
$#%-
4QQO/QPKVQT
$CUG5GVWR
#PUY5GVWR
1-
$#%-
$#%-
1-
•Handset
570#
*CPFUGV
0GY%+&
MENU
/'07
&KTGEV.KPM/QFG
4QQO/QPKVQT
*CPFUGV5GVWR
$#%-
$#%-
∨
1-
&KTGEV.KPM/QFG
4QQO/QPKVQT
*CPFUGV5GVWR
$#%-
$#%-
OK
6QGPVGT
&KTGEV.KPMOQFG
RTGUU='06'4?
$#%-
$#%-
'06'4
Enter
570#
*CPFUGV
&KTGEV.KPM/QFG
%#0%'.
&KTGEV.KPM
∨
1-
&KTGEV.KPM/QFG
4QQO/QPKVQT
*CPFUGV5GVWR
$#%-
OK
∧
or
∨
.KUVGPVQ
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
*CPFUGV
$CUG
$#%-
$#%-
∧
or
∨
1-
∨
1-
OK
OK
*#0&5'65'672
4KPIGT8QNWOG
4KPIGT6QPGU
&KUVKPEVKXG4KPI
#WVQ6CNM
#P[MG[#PUYGT
$CPPGT
.CPIWCIG
.%&%QPVTCUV
-G[6QWEJ6QPG
#PKOCVKQP5ETGGP
4QQO/QPKVQT
$#%-
$#%-
or
$#5'5'672
.CPIWCIG
%QPVTCUV
$#%-
$#%-
1-
OK
1-
MAIN MENU FLOW CHART [90]
MA I N M E N U F L O W C H A RT
www.uniden.com
$#%-
•Base
4QQO/QPKVQT
$CUG5GVWR
#PUY5GVWR
$#%-
$#%-
$CUG5GVWR
#PUY5GVWR
)NQDCN5GVWR
1-
$#%-
$#%-
1-
•Handset
∨
4QQO/QPKVQT
*CPFUGV5GVWR
#PUY5GVWR
$#%-
$#%-
*CPFUGV5GVWR
#PUY5GVWR
)NQDCN5GVWR
∨
$#%-
1-
$#%-
OK
∧
or
∨
$#%-
1-
#PUY5GVWR
)NQDCN5GVWR
&GTGIKUVGT*5
$#%-
$#%-
OK
#0595'672
5GEWTKV[%QFG
4KPI6KOG
4GEQTF6KOG
/GUUCIG#NGTV
.CPIWCIG
%CNN5ETGGP
$#%-
∨
or
1-
#0595'672
4GEQTF)TGGVKPI
5GNGEV)TGGVKPI
5GEWTKV[%QFG
4KPI6KOG
4GEQTF6KOG
/GUUCIG#NGTV
.CPIWCIG
%CNN5ETGGP
$#%-
$#%-
∧
or
∨
).1$#.5'672
&C[6KOG
%+&%9
#TGC%QFG
&KCN/QFG
$#%-
$#%-
1-
OK
1-
∧
or
∨
&GTGIKUVGT*5!
;GU
0Q
$#%-
$#%-
1-
OK
&GTGIKUVTCVKQP
%QORNGVG
1$#%-
1-
www.uniden.com
M A I N M E N U F L O W C H A RT
[91] MAIN MENU FLOW CHART
$#%-
Memo
www.uniden.com
[92]
Memo
[93]
www.uniden.com
At Uniden, we'll take care of you!
Thank you for purchasing a Uniden product. If you have any questions or problems,
please do not return this product to the place of purchase.
Having Trouble?
Our customer care specialists are here to help you! Visit our website at www.uniden.com or call
our Customer Service Hotline at 1-800-297-1023, Mon-Fri, 7 a.m. to 7 p.m. or Sat/Sun, 9
a.m. to 5 p.m. CST. (The Customer Service Hotline is closed on holidays.)
Need a Part?
To order headsets, additional handsets, replacement batteries or other accessories, visit
our website at www.uniden.com or call 1-800-554-3988, Mon-Fri, 8 a.m. to 5 p.m. CST.
Help for our Special Needs Customers
If you need special assistance due to a disability or have questions on the accessibility
features of this product, please call 1-800-874-9314 (voice or TTY)
May be covered under one or more of the following U.S. patents:
4,797,916 5,381,460 5,426,690 5,434,905 5,491,745 5,493,605
5,533,010 5,574,727 5,581,598 5,650,790 5,660,269 5,661,780
5,663,981 5,671,248 5,696,471 5,717,312 5,732,355 5,754,407
5,758,289 5,768,345 5,787,356 5,794,152 5,801,466 5,825,161
5,864,619 5,893,034 5,912,968 5,915,227 5,929,598 5,930,720
5,960,358 5,987,330 6,044,281 6,070,082 6,125,277 6,253,088
6,314,278 6,418,209 6,618,015 6,671,315 6,714,630 6,782,098
6,788,920 6,788,953
Other patents pending.
R
IE
S,
M
@
E CO
SO IN
.
S
E NL EN
D
CC
A O O NI
.U
G
W
W
W
FO
R
R E G I S T E R O N L I N E T O D AY !
T H A N K Y O U F O R B U Y I N G A U N I D E N P R O D U C T.
©2005 Uniden America Corporation, Fort Worth, Texas. Contains additional foreign articles. Custom manufactured in China.
UPZZ01777BZ(0)