dt VAXstation 4000 Model 60 Optional Devices Service Information EK-V4066-SV.001

dt VAXstation 4000 Model 60 Optional Devices Service Information EK-V4066-SV.001

dt

VAXstation 4000 Model 60

Optional Devices Service Information

EK-V4066-SV.001

Digital Equipment Corporation

Maynard, Massachusetts

First Edition, February 1992.

The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation. Digital Equipment

Corporation assumes no responsibility for any errors that may appear in this document.

The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.

No responsibility is assumed for the use or reliability of software on equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.

Restricted Rights: Use, duplication, or disclosure by the U. S. Government is subject to restrictions as set forth in subparagraph ( c ) ( 1 ) ( ii ) of the Rights in Technical Data and Computer Software clause at DFARS 252.227–7013.

Copyright © by Digital Equipment Corporation 1992

All Rights Reserved.

Printed in U.S.A.

The following are trademarks of Digital Equipment Corporation: DEC, DECstation,

DEMPR, DIGITAL, MicroVAX, ULTRIX, VAX, VMS, and the DIGITAL logo.

This document was prepared using VAX DOCUMENT, Version 2.0.

Contents

Preface

vii

1 Mass Storage Devices

1.1

RZ2x Hard Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1–2

1.1.1

1.1.2

RZ2x Hard Disk Drive SCSI ID . . . . . . . . . . . . . . . . . . . . .

RZ2x Hard Disk Drive Specifications . . . . . . . . . . . . . . . . .

1–2

1–5

1.2

RRD42 CDROM Disc Drive . . . . . . . . . . . . . . . . . . . . . . . . . .

1–6

1.2.1

RRD42 CDROM Disc Drive SCSI ID . . . . . . . . . . . . . . . . .

1–6

1.2.2

RRD42 CDROM Disc Drive Specifications . . . . . . . . . . . . .

1–9

1.3

RX26 Diskette Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10

1.3.1

1.3.2

RX26 Diskette Drive SCSI ID . . . . . . . . . . . . . . . . . . . . . . 1–10

RX26 Diskette Drive Specifications . . . . . . . . . . . . . . . . . . 1–12

1.4

TZK10 (QIC) Tape Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13

1.4.1

TZK10 Tape Drive SCSI ID . . . . . . . . . . . . . . . . . . . . . . . . 1–13

1.4.2

TZK10 Tape Drive Specifications . . . . . . . . . . . . . . . . . . . . 1–16

2 Optional System Modules

2.1

MS44 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–2

2.1.1

MS44 Memory Module Specifications . . . . . . . . . . . . . . . . .

2–4

2.2

DSW21 Synchronous Communications Adapter . . . . . . . . . . .

2–5

2.2.1

2.2.2

DSW21 Synchronous Communications Adapter Cables . . .

Installing the DSW21 Adapter . . . . . . . . . . . . . . . . . . . . . .

2–7

2–7

2.2.3

2.2.4

DSW21 Environmental Specifications . . . . . . . . . . . . . . . .

2–8

DSW21 Physical Specifications . . . . . . . . . . . . . . . . . . . . .

2–9 iii

iv Contents

3 Optional System Monitors

3.1

VR319 Monochrome Monitor . . . . . . . . . . . . . . . . . . . . . . . . .

3–2

3.1.1

3.1.2

Refresh Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–3

VR319 Monochrome Monitor Specifications . . . . . . . . . . . .

3–5

3.1.2.1

VR319 Monochrome Monitor Video Timing . . . . . . . . . .

3–6

3.2

VR320 Color Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–7

3.2.1

3.2.2

Refresh Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–8

VR320 Color Monitor Specifications . . . . . . . . . . . . . . . . . . 3–10

3.2.2.1

VR320 Color Monitor Video Timing . . . . . . . . . . . . . . . .

3–11

3.3

VR262 Monochrome Monitor . . . . . . . . . . . . . . . . . . . . . . . . . 3–12

3.3.1

VR262 Monochrome Monitor Specifications . . . . . . . . . . . . 3–12

3.4

VR299 Color Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14

3.4.1

VR299 Color Monitor Specifications . . . . . . . . . . . . . . . . . . 3–14

3.5

VRT16 Color Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–15

3.5.1

VRT16 Color Monitor Specifications . . . . . . . . . . . . . . . . . . 3–15

3.6

VRT19 Color Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–16

3.6.1

VRT19 Color Monitor Specifications . . . . . . . . . . . . . . . . . . 3–16

4 Optional System Printers

4.1

LA75 Companion Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–2

4.1.1

4.1.2

LA75 Companion Printer Configuration . . . . . . . . . . . . . . .

4–4

LA75 Companion Printer Specifications . . . . . . . . . . . . . . .

4–5

4.2

LA210 Letterprinter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–6

4.2.1

LA210 Letterprinter Configuration . . . . . . . . . . . . . . . . . .

4–9

4.2.2

LA210 Letterprinter Specifications . . . . . . . . . . . . . . . . . .

4–11

4.3

LN03 Laser Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12

4.3.1

4.3.2

LN03 Laser Printer Configuration . . . . . . . . . . . . . . . . . . . 4–13

LN03 Laser Printer Specifications . . . . . . . . . . . . . . . . . . . 4–15

Index

Contents v

Figures

1–1 RZ23L SCSI ID Jumper Location . . . . . . . . . . . . . . . . . . . . . .

1–3

1–2 RRD42 CDROM Disc Drive Jumper Location . . . . . . . . . . . .

1–7

1–3 RX26 Diskette Drive SCSI ID Switch Location . . . . . . . . . . .

1–11

1–4 Verifying the TZK10 Tape Drive SCSI ID . . . . . . . . . . . . . . . 1–14

2–1 MS44 Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–3

2–2 DSW21 Synchronous Communications Adapter . . . . . . . . . . .

2–5

2–3 DSW21 Synchronous Communications Adapter . . . . . . . . . . .

2–6

3–1 VR319 Monochrome Monitor . . . . . . . . . . . . . . . . . . . . . . . . .

3–2

3–2 Refresh Rate Jumper—Deflection Module . . . . . . . . . . . . . . .

3–3

3–3 Refresh Rate Jumper—Power Supply Module . . . . . . . . . . . .

3–4

3–4 VR320 Color Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3–7

3–5 Refresh Rate Switch—Deflection Module . . . . . . . . . . . . . . . .

3–8

3–6 Refresh Rate Jumper—Power Supply Module . . . . . . . . . . . .

3–9

4–1 LA75 Companion Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–3

4–2 LA210 Letterprinter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4–6

4–3 RS232C Serial Interface Connector . . . . . . . . . . . . . . . . . . . .

4–7

4–4 Parallel Interface Switches (Optional) . . . . . . . . . . . . . . . . . .

4–8

4–5 LA210 Letterprinter Configuration Switches . . . . . . . . . . . . . 4–10

4–6 LN03 Laser Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12

4–7 LN03 Laser Printer Configuration Switches . . . . . . . . . . . . . 4–14

Tables

1–1 Capacities of RZ23L, RZ24, and RZ25 Drives . . . . . . . . . . . .

1–2

1–2 RZ23L/RZ24 SCSI Jumper Settings . . . . . . . . . . . . . . . . . . . .

1–4

1–3 RZ25 SCSI Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . .

1–4

1–4 RZ23L Disk Drive Operating Environment . . . . . . . . . . . . . .

1–5

1–5 RZ23L Disk Drive Physical Dimensions . . . . . . . . . . . . . . . . .

1–5

1–6 RZ24 Disk Drive Operating Environment . . . . . . . . . . . . . . .

1–5

1–7 RZ24 Disk Drive Physical Dimensions . . . . . . . . . . . . . . . . . .

1–6

1–8 RRD42 CDROM Disc Drive Jumper Settings . . . . . . . . . . . . .

1–8

1–9 RRD42 Disc Drive Operating Environment . . . . . . . . . . . . . .

1–9

1–10 RX26 Diskette SCSI ID Switch Setting . . . . . . . . . . . . . . . . .

1–11

1–11 RX26 Environmental Specifications . . . . . . . . . . . . . . . . . . . . 1–12

1–12 Diskette and Format Information . . . . . . . . . . . . . . . . . . . . . 1–12

vi Contents

1–13 TZK10 Tape Drive SCSI Jumper Settings . . . . . . . . . . . . . . . 1–15

1–14 TZK10 Cartridge Tape Drive Dimensions . . . . . . . . . . . . . . . 1–16

1–15 TZK10 Cartridge Tape Drive Operating Environment . . . . . . 1–16

2–1 DSW21 Adapter Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–7

2–2 DSW21 Environmental Specifications . . . . . . . . . . . . . . . . . .

2–8

2–3 Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2–9

4–1 LA75 Factory Set Configurations . . . . . . . . . . . . . . . . . . . . . .

4–4

Preface

This manual is a support and reference document for Digital Services personnel who perform maintenance on the VAXstation 4000 Model

60 workstation. It is also intended for Digital customers who have a self-maintenance agreement with Digital.

Organization of This Manual

This manual contains the following chapters:

• Chapter 1 describes the optional mass storage devices that can be configured with the system, and explains how to install the devices.

• Chapter 2 describes the optional system modules that can be configured with the system. Installation procedures for each module are also in this chapter.

• Chapter 3 describes the optional monitors that can be configured with the system.

• Chapter 4 describes the optional printers that can be configured with the system.

Associated Documentation

The following documents provide additional information about the

VAXstation 4000 Model 60 workstation:

Document

VAXstation 4000 Model 60 Documentation

Kit

VAXstation 4000 Model 60 Service

Information

VAXstation 4000 Model 60 Pocket Service

Information

VAXstation 4000 Model 60 Quick

Installation Card

Part Number

EK-V4666-DK

EK-V466B-SV

EK-V466H-PS

EK-PMARI-IN vii

viii Preface

Document

VAXstation 4000 Model 60 Owner’s and

System Installation Guide

VAXstation 4000 Model 60 Options

Installation Guide

VAXstation 4000 Model VLC Service

Information

BA46 Storage Expansion Box Owner’s

Guide

BA46 Storage Expansion Box Maintenance

Guide

BA42 Storage Expansion Box Maintenance

Guide

Part Number

EK-PMARI-OM

EK-PVAX2-IG

EK-V48VB-SV

EK-STEXP-IG

EK-VBA46-SV

EK-BA42A-MG

Conventions

The following conventions are used in this guide.

Convention

WARNING

CAUTION

NOTE

PN

Description

Contains important information that relate to personal safety.

Contains information to prevent damage to the equipment.

Contains general information.

Part number

1

Mass Storage Devices

This chapter describes the optional mass storage devices that can be configured in the VAXstation 4000 Model 60 system unit. The devices are:

Section 1.1

Section 1.2

Section 1.3

Section 1.4

RZ23L, RZ24, and RZ25 Hard Disk Drives

RRD42 Compact Disc Drive

RX26 Diskette Drive

TZK10 Tape Drive

NOTE

The system unit can hold one device from which the storage medium is removable, such as the RRD42, RX26, or TZK10 drives.

To add more than one removable media device, you need an expansion box.

1–1

1–2 Mass Storage Devices

1.1 RZ2x Hard Disk Drive

The RZ23L, RZ24, and RZ25 hard disk drives provide memory storage for applications and user files. The RZ2x drives store information on a non-removable disk. Table 1–1 lists the storage capacities for the RZ2x drives.

Table 1–1 Capacities of RZ23L, RZ24, and RZ25 Drives

Drive Capacity

RZ23L

RZ24

RZ25

121 MB

209 MB

426 MB

1.1.1 RZ2x Hard Disk Drive SCSI ID

Before you install the RZ23L, RZ24, or RZ25 drive in the system, you need to verify the SCSI ID setting as follows:

1.

Turn the RZ23L, RZ24, or RZ25 drive so that the bottom of the drive is facing you. Find the SCSI ID jumpers, which are removable electrical connectors, that allow you to select a unique ID number for each SCSI device:

— If you have an RZ23L or RZ24 drive, find jumpers E1, E2, and E3.

— If you have an RZ25 drive, find jumpers P1, P2, and P3.

NOTE

If your hard disk drive was not factory installed, it could have been shipped with all the jumpers attached (to prevent loss of jumpers when shipping and unpacking). In this case, the SCSI

ID is set to 7, and you may need to change it.

2.

Verify that the jumpers are set to the appropriate positions for SCSI

ID 0, 1, or 2. These are the positions that the RZ2x drive normally uses. If you have one RZ23L, RZ24, or RZ25 drive that was factory installed, verify that the jumpers are set for SCSI ID 3. If you have two RZ23L, RZ24, or RZ25 drives that were factory installed, verify that the jumpers on one of them are set for SCSI ID 3, and that the jumpers on the other are set to either SCSI ID 0, 1, or 2. Any RZ2x drive can be set to SCSI ID 0, 1, 2, or 3, if no other drive uses that

ID. See Table 1–2 (for RZ23L and RZ24 drives) or Table 1–3 (for RZ25 drives) for the correct jumper positions for each of these SCSI IDs.

Mass Storage Devices 1–3

NOTE

Settings should be changed only when a system is configured with more than one of a particular device. You are responsible for the

SCSI ID settings on your equipment.

If you are adding an RZ23L, RZ24, or RZ25 drive, the SCSI ID could need changing. Drives not factory installed could have all jumpers in place (set for position 7) to prevent misplacing the jumpers during shipping and unpacking.

Figure 1–1 shows the location of the RZ2x drive SCSI ID jumpers.

Figure 1–1 RZ23L SCSI ID Jumper Location

SCSI ID Jumpers

Internal Power

Connector

Jumpers

E4

E3

E2

E1

SCSI ID 3

Off/Out

On/In

On/In

SCSI Signal

Connector E3

E2

E1

MLO-002895

1–4 Mass Storage Devices

Table 1–2 RZ23L/RZ24 SCSI Jumper Settings

Device

Recommended

SCSI ID E1

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

(factory-installed)

RRD42

RX26/TZK10

SCSI controller

High-priority device

6

7

4

5

2

3

0

1

Out

In

Out

In

Out

1

In

1

Out

In

Jumper Positions

E2 E3

Out

Out

In

In

Out

Out

In

In

In

In

In

In

Out

Out

Out

Out

1

Out = Removed; In = attached

Table 1–3 RZ25 SCSI Jumper Settings

Device

Recommended

SCSI ID

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

(factory-installed)

RRD42

RX26/TZK10

SCSI controller

High-priority device

4

5

6

7

2

3

0

1

1

Out = Removed; In = attached

In

In

In

In

P1

Out

1

Out

Out

Out

Jumper Positions

P2 P3

Out

Out

In

In

Out

In

1

Out

In

Out

Out

In

In

Out

In

Out

In

For information on installing the RZ2x disk drives, refer to the VAXstation

4000 Model 60 Options Installation Guide (PN EK-PVAX2-IG).

Mass Storage Devices 1–5

1.1.2 RZ2x Hard Disk Drive Specifications

Table 1–4 and Table 1–5 list the specifications for the RZ23L hard disk drive. Table 1–6 and Table 1–7 list the specifications for the RZ24 hard disk drive.

Table 1–4 RZ23L Disk Drive Operating Environment

Temperature range

Relative humidity

Altitude

Maximum wet bulb temperature

Heat dissipation

10° C to 60° C (50° F to 110° F)

8% to 80%

-304 m to 3048 m (-1000 ft to 10,000 ft)

25.6° C (78° F)

Temperature gradient

8 W (typical) (27.36 Btu/hr)

9 W max. (30.8 Btu/hr)

11° C/hr (20° F/hr)

Table 1–5 RZ23L Disk Drive Physical Dimensions

Height Width Depth Weight

41.28 mm

(1.625 in)

101.6 mm

(4.00 in)

146.05 mm

(5.75 in)

.826 kg

(1.82 lbs)

Table 1–6 RZ24 Disk Drive Operating Environment

Temperature range

Relative humidity

Altitude

Maximum wet bulb temperature

Heat dissipation

10° C to 55° C (50° F to 99° F)

8% to 80%

-304 m to 4573 m (-1000 ft to 15,000 ft)

25.6° C (78° F)

Temperature gradient

6.6 W (seeking) (22.57 Btu/hr)

6.8 W (read/write mode) (23.26 Btu/hr)

11° C/hr (20° F/hr)

1–6 Mass Storage Devices

Table 1–7 RZ24 Disk Drive Physical Dimensions

Height Width Depth Weight

41.28 mm

(1.625 in)

101.6 mm

(4.00 in)

146.05 mm

(5.75 in)

.780 kg

(1.72 lbs)

1.2 RRD42 CDROM Disc Drive

The RRD42 CDROM compact disc drive is a storage device that reads data from removable compact discs. The drive has a storage capacity of

600 Mbytes. The RRD42 drive can be used to install the VMS operating system and other software, and to access read-only databases, such as online documentation sets. The drive has audio output capabilities, allowing the use of headphones for listening to audio information recorded on the compact disc.

1.2.1 RRD42 CDROM Disc Drive SCSI ID

Before installing the RRD42 drive, verify the SCSI ID on the drive as follows:

1.

Turn the RRD42 drive so that the rear of the drive is facing you. Find

SCSI ID jumpers 0, 1, and 2, on the rear of the drive, as shown in

Figure 1–2. Jumpers are removable electrical connectors that allow you to select a unique ID number for each SCSI device.

2.

Verify that the jumpers are set as follows:

Jumper 0 = Out (removed)

Jumper 1 = Out (removed)

Jumper 2 = In (attached)

These are the positions for SCSI ID 4, which is the default SCSI ID for the drive.

Mass Storage Devices 1–7

Figure 1–2 RRD42 CDROM Disc Drive Jumper Location

MODE

NOTE

Default settings should be changed only when a system is configured with more than one of a particular device. You are responsible for the SCSI ID settings on your equipment.

If you want to use a different ID, choose a new ID from Table 1–8, and carefully remove or replace jumpers accordingly, using tweezers or another small tool.

NOTE

Save any SCSI jumpers you remove for later use, if necessary.

CAUTION

Never set two devices to the same SCSI ID; the system cannot communicate with devices set to the same ID.

1–8 Mass Storage Devices

Table 1–8 lists the jumper settings for the RRD42 disc drive.

Table 1–8 RRD42 CDROM Disc Drive Jumper Settings

Device

Recommended

SCSI ID 0

Jumper Positions

1 2

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

Factory-installed

RZ23L/RZ24/RZ25

RRD42

RX26/TZK10

SCSI controller

High-priority device

6

7

4

5

2

3

0

1

Out

In

Out

In

Out

1

In

1

Out

In

Out

Out

In

In

Out

Out

In

In

Out

Out

Out

Out

In

In

In

In

1

Out = Removed; In = Attached

To install the RRD42 drive, refer to the VAXstation 4000 Model 60 Options

Installation Guide (PN EK-PMARI-IG).

Mass Storage Devices 1–9

1.2.2 RRD42 CDROM Disc Drive Specifications

Table 1–9 lists the operating environment for RRD42 disc drive.

Table 1–9 RRD42 Disc Drive Operating Environment

Temperature range

Relative humidity

Altitude

Maximum wet bulb temperature

5° C to 50° C (41° F to 122° F)

10% to 90%, non-condensing

2400 m (8000 ft) at 36° C (96° F)

29° C (84° F)

NOTE

Be sure the "Mode" jumper is in. This jumper must be in place to use the drive with the VMS operating system.

CAUTION

Each device must have a unique SCSI ID. Never set two devices to the same SCSI ID; the system cannot communicate with devices set to the same ID.

1–10 Mass Storage Devices

1.3 RX26 Diskette Drive

The RX26 is a half-height diskette drive that can be used for selective file backup, load applications, and transporting files between non-networked systems. The RX26 drive has a storage capacity of 4 Mbytes. It can be used to read and write on 4 Mbyte standard floppies, and to read only 700

KB standard floppies.

1.3.1 RX26 Diskette Drive SCSI ID

Before installing the RX26 drive in the system, verify the SCSI ID setting.

1.

Turn the RX26 drive so that the left side of the drive is facing you.

Find the SCSI ID switches 1, 2, and 3 on the drive, as shown in

Figure 1–3.

2.

Use a pen or small pointed object to move the switches up or down.

CAUTION

Do not use a pencil to move switches. Graphite particles can damage the SCSI switches.

Digital recommends that the SCSI ID switches be set to 5 as follows:

Switch 1 = Down (on)

Switch 2 = Up (off)

Switch 3 = Down (on)

NOTE

Default settings should be changed only when a system is configured with more than one of a particular device. You are responsible for the SCSI ID settings on your equipment.

If you need to use a different ID, choose a new ID from Table 1–10. Use a small pointed instrument (but not a pencil), set the switches accordingly.

CAUTION

Never set two devices to the same SCSI ID; the system cannot communicate with devices set to the same ID.

To install the RX26 drive, refer to the VAXstation 4000 Model 60 Options

Installation Guide (PN EK-PMARI-IG).

Mass Storage Devices 1–11

Figure 1–3 RX26 Diskette Drive SCSI ID Switch Location

Switches Positions:

Up (Off)

Down (On)

SCSI ID 5

1 2 3

1 2 3

MLO-002886

Table 1–10 RX26 Diskette SCSI ID Switch Setting

Device

Recommended

SCSI ID 2

Switch Positions

1 0

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

Factory-installed

RZ23L/RZ24/RZ25

RRD42

RX26/TZK10

SCSI controller

(High-priority device)

6

7

4

5

2

3

0

1

Up

Down

Up

Down

Up

Down

Up

Down

Up

Up

Down

Down

Up

Up

Down

Down

Up

Up

Up

Up

Down

Down

Down

Down

1–12 Mass Storage Devices

1.3.2 RX26 Diskette Drive Specifications

Table 1–11 RX26 Environmental Specifications

Operating temperature

Nonoperating temperature

Operating humidity

Nonoperating humidity

Operating altitude

Nonoperating altitude

5° C to 50° C (40° F to 122° F)

-20° C to 66° C (-4° F to 151° F)

8% to 80%, wet bulb @ 25.6° C (78.0° F), no condensation

5% to 95%, wet bulb @ 46° C (115.0° F), no condensation

-304 m to 3,048 m (-1000 ft to 10,000 ft)

-304 m to 12,192 m (-1000 ft to 40,000 ft)

Table 1–12 Diskette and Format Information

Number of cylinders

Number of tracks

Number of read/write heads

80

160

2

Mass Storage Devices 1–13

1.4 TZK10 (QIC) Tape Drive

The TZK10 tape drive is a half-height device that uses industry standard quarter-inch cartridge (QIC) tapes for loading applications and doing file backups. The formatted capacity of the QIC tape is 320 Mbytes or 525

Mbytes, depending on the tape used.

1.4.1 TZK10 Tape Drive SCSI ID

Before installing the TZK10 drive, verify the SCSI ID on the drive as follows:

1.

Turn the TZK10 drive so that the rear of the drive is facing you.

Find SCSI ID jumpers 0, 1, and 2. Jumpers are removable electrical connectors that allow you to select a distinct ID for each SCSI device.

2.

Verify that the jumpers are set as follows:

Jumper 0 = In (attached)

Jumper 1 = Out (removed)

Jumper 2 = In (attached)

These are the positions for SCSI ID 5, which is the setting that the TZK10 drive normally uses.

NOTE

Default settings should be changed only when a system is configured with more than one of a particular device. You are responsible for the SCSI ID settings on your equipment.

1–14 Mass Storage Devices

Figure 1–4 Verifying the TZK10 Tape Drive SCSI ID

Parity 2 1 0

MLO-006156

Mass Storage Devices 1–15

If you want to use a different ID, choose a new ID from Table 1–13 and carefully remove or replace jumpers accordingly. Use tweezers or another small tool to remove or replace jumpers.

NOTE

Save any SCSI jumpers you remove for later use, if necessary.

Table 1–13 TZK10 Tape Drive SCSI Jumper Settings

Device

Recommended

SCSI ID 2

Jumper Positions

1 0

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

RZ23L/RZ24/RZ25

Factory-installed

RZ23L/RZ24/RZ25

RRD42

RX26/TZK10

SCSI controller

High-priority device

6

7

4

5

0

1

2

3

In

In

In

In

Out

Out

Out

Out

Out

Out

In

In

Out

Out

In

In

Out

In

Out

In

Out

In

Out

In

NOTE

Be sure the "Mode Select" jumper is in. This jumper must be in place to use the drive with the VMS operating system.

CAUTION

Each device must have a unique SCSI ID. Never set two devices to the same SCSI ID; the system cannot communicate with devices set to the same ID.

For information on installing the TZK10 (QIC) tape drives, refer to the

VAXstation 4000 Model 60 Options Installation Guide (PN EK-PVAX2-IG).

1–16 Mass Storage Devices

1.4.2 TZK10 Tape Drive Specifications

Table 1–14 TZK10 Cartridge Tape Drive Dimensions

Height Width Depth Weight

4.4 cm

(1.7 in)

14.6 cm

(5.25 in)

20.8 cm

(8.2 in)

1.1 kg

(2.4 lbs)

Table 1–15 TZK10 Cartridge Tape Drive Operating Environment

Temperature range

Relative humidity

Altitude

Maximum wet bulb temperature

Minimum dew point

5° C to 40° C (41° F to 122° F)

10% to 90%, non-condensing

0 m to 2400 m (0 ft to 13,000 ft)

26° C (79° F)

2° C (36° F)

2

Optional System Modules

This chapter describes the optional modules that can be installed in the

VAXstation 4000 Model 60 system. The optional modules are:

Section 2.1

Section 2.2

MS44 Memory Module

DSW21 Synchronous Communications Adapter

2–1

2–2 Optional System Modules

2.1 MS44 Memory Module

The MS44 memory module is designed to provide expandable memory for the VAXstation 4000 Model 60 system. The memory array consists of 36 DRAMs organized as one bank of four- to nine-bit bytes. Timing and addressing of the array are provided by the system module and are buffered on the memory module. Data lines are unbuffered on the module and are driven on bi-directional lines to and from the DRAMs. All data and control lines receive one unit load per module.

Three types of memory module are available: 4 Mbyte (MS44-AA),

4 Mbyte Reduced Cost (MS44-AL), and 16 Mbyte (MS44-CA). The

VAXstation 4000 Model 60 can use any of the three memory modules.

Memory modules must be installed in pairs; two 4 Mbyte modules for two

16 Mbyte modules.

To identify a memory module, locate the etch on the left side of the memory module. The 4 Mbyte modules have AA or AL on the etch board, and the 16 Mbyte modules have CA on the etch board. The memory modules are shown in Figure 2–1.

When the module pairs are configured together, the MS44-AA module pairs should be installed in the lower numbered areas. The maximum system memory configuration is 104 Mbytes for the Model 60.

For additional information on installing memory modules, refer to the

VAXstation 4000 Model 60 Service Information (PN EK-V466B-SV).

Figure 2–1 MS44 Memory Module

AA = 4 Megabyte

Memory Board

AA-A8

Optional System Modules 2–3

CA-A8

CA = 16 Megabyte

Memory Board

LJ-00499-TI0

2–4 Optional System Modules

2.1.1 MS44 Memory Module Specifications

The MS44 memory module specifications are listed next.

Total Memory Power Required

Total DRAM Current

Total Driver Current

Total Current

Total Active Power

Total Standby Power

2.45 A

0.10 A

2.55 A

13.38 W

1.25 W

Total System Requirements

Total Memory Current

Total Memory Power

5.69 A

29.86 W

NOTE

The current specifications for the memory modules assume 24

Mbytes and QUADWORD operations with 2 memory modules active and 4 memory modules in standby.

Optional System Modules 2–5

2.2 DSW21 Synchronous Communications Adapter

The DSW21 adapter is a synchronous serial communications interface for the VAXstation 4000 Model 60 workstation. It has full modem control and multiple protocol support. Figure 2–2 shows the DSW21 communications adapter.

Figure 2–2 DSW21 Synchronous Communications Adapter

MLO-005915

The DSW21 adapter is an option board that connects internally to the

CPU board via a 64-pin option connector. It consists of the EDAL interface, 128 KB UVEPROM, 256 KB Static RAM, the MC68302

Integrated Multi-Protocol Processor (IMP), and I/O receivers and drivers with static and lightning protection. The communications I/O connector is a 50-pin D-subminiature plug that goes directly through the back of the system cabinet. Figure 2–3 shows the DSW21 connections.

2–6 Optional System Modules

Figure 2–3 DSW21 Synchronous Communications Adapter

64−PIN

CONN

128K BYTE

PROM

256K BYTE

SRAM

50−PIN

CONN

EDAL

R/W

PAL

CONTROL

LOGIC

MC68302

IMP

T

X

I/O

R

X

INTERRUPT

LJ−01668−GRA

Optional System Modules 2–7

2.2.1 DSW21 Synchronous Communications Adapter Cables

Adapter cables for the DSW21 communications adapter vary according to the option ordered. The following table lists the adapter cable variations.

Table 2–1 DSW21 Adapter Cables

DSW21 Model Adapter Cables

DSW21-AA

DSW21-AB

DSW21-AC

DSW21-AD

DSW21-AE

DSW21-AF

DSW21-M

1 line sync comm, BC19V EIA-232/V.24

1 line sync comm, BC19W EIA-449/423/V.10

1 line sync comm, BC19U EIA-449/422/V.36

1 line sync comm, BC19X V.35

1 line sync comm, BC19Q EIA-530

1 line sync comm, BC20Q X.21

1 line sync comm controller, no adapter cable

2.2.2 Installing the DSW21 Adapter

This section describes how to install the DSW21 interface in the system unit.

NOTE

Refer to the system preparation instructions in the VAXstation

4000 Model 60 Service Information before installing any module in the workstation.

To install the communications interface, do the following:

1.

Remove any rear panels or shields (if applicable) from the I/O panel.

2.

Mount the DSW21 internally to the Model 60 via the 64-pin option connector. There are no clips or screws to hold the option connector.

3.

Attach the 50-pin data connector, which protrudes through the rear of the enclosure and is held in place by the metal bracket.

4.

Restore the system. Test the new configuration.

2–8 Optional System Modules

2.2.3 DSW21 Environmental Specifications

The DSW21 module assembly meets Digital Standard 102 class C environmental specifications.

Table 2–2 DSW21 Environmental Specifications

Parameter Range

Operating temperature

Nonoperating temperature

Relative humidity

(operating)

Relative humidity

(nonoperating)

Maximum wet bulb temperature (operating)

Maximum wet bulb temperature (nonoperating)

Minimum dew point temperature (operating)

Head dissipation

Altitude (operating)

Altitude (nonoperating)

5°C to 50° C (41°F to 122 °F)

-40°C to 66° C (-40°F to 155°F)

10% to 95% ( noncondensing)

10% to 95%

32 °C (90°F)

46 °C (115°F)

2 °C (36°F)

6.75 watts to 8.10 watts Btu/h

2400 m (8000 ft)

4900 m (16000 ft)

NOTE

De-rate the maximum operating temperature by 1.82 degrees

Celsius for each 1000 meters of altitude above sea level.

Reference: Standard Atmosphere, Standard Gravity.

This device is to operate in a non-caustic environment.

Optional System Modules 2–9

2.2.4 DSW21 Physical Specifications

The DSW21 adapter is a four layer circuit board assembly with the following specifications.

Table 2–3 Physical Specifications

Parameter Range

Height

Width

Depth

Weight

4.3 cm (1.7 in)

12.4 cm (4.9 in)

14 cm (5.5 in)

.45 kg (1 lb)

3

Optional System Monitors

This chapter describes the optional monitors that can be connected externally to the VAXstation 4000 Model 60 system. The monitors are:

Section 3.1

Section 3.2

Section 3.3

Section 3.4

Section 3.5

Section 3.6

VR319 Monochrome Monitor

VR320 Color Monitor

VR262 Monochrome Monitor

VR299 Color Monitor

VRT16 Color Monitor

VRT19 Color Monitor

3–1

3–2 Optional System Monitors

3.1 VR319 Monochrome Monitor

The VR319 monochrome monitor (Figure 3–1) has a 500 mm (20 in), direct-viewed, anti-glare CRT. The built-in tilt/swivel assembly allows you to adjust the screen for viewing.

Figure 3–1 VR319 Monochrome Monitor

M A - 0 2 4 3 - 9 0 . D G

Optional System Monitors 3–3

3.1.1 Refresh Rate

The VR319 monochrome monitor operates at either a 66 Hz or 72 Hz refresh rate. The refresh rate is preset for the system before the monitor is shipped. If you change the monitor to another system, check the refresh rate of the new system and then set the jumpers on the deflection module

(Figure 3–2) and power supply module (Figure 3–3) to match the new system. For additional information, refer to the VR319 Monitor Service

Guide (PN EK-VR319-SV).

Figure 3–2 Refresh Rate Jumper—Deflection Module

D e f l e c t i o n M o d u l e

6 6 / 7 2 H z D e f l e c t i o n

J u m p e r

6 6 H z

7 2 H z

Refresh Jumper M A - 1 2 3 0 - 8 9 . D G

L J - 0 0 5 2 4 - T I 0

3–4 Optional System Monitors

Figure 3–3 Refresh Rate Jumper—Power Supply Module

P o w e r S u p p l y M o d u l e

6 6 / 7 2 H z P o w e r S u p p l y

J u m p e r

6 6 H z

7 2 H z

R e f r e s h J u m p e r

M A - 1 2 4 3 - 8 9 . D G

L J - 0 0 5 2 3 - T I 0

Optional System Monitors 3–5

3.1.2 VR319 Monochrome Monitor Specifications

The VR319 monochrome monitor specifications are listed next.

Power Requirements

Voltage

Frequency

Power Consumption

Operating Environment

Temperature Range

Relative humidity

88 to 132 Vac or 176 to 264 Vac auto-ranging, single phase, 3-wire

47 to 63 Hz

135 W maximum

10° C to 40° C (50° F to 104° F)

10% to 95%

Maximum wet bulb = 32° C Minimum dew point = 2°C (noncondensing)

Physical Characteristics

Height

Width

Depth

Weight

Tilt Range

Swivel Range

Display - Cathode ray tube

(CRT)

Display area

Light transmission

Video input

45.7 cm (18.0 in)

49.5 cm (19.5 in)

40.1 cm (15.8 in)

22 kg (48.0 lb)

-5° forward to +15° backward

±90° (left and right)

48.3 cm (19 in) diagonal

1280 pixels horizontal x 1024 lines vertical.

Approximate picture size: 34.3 cm

(13.5 in) x 27.3 cm (10.75 in) with a

5:4 aspect ratio.

42% nominal

Composite video

3–6 Optional System Monitors

3.1.2.1 VR319 Monochrome Monitor Video Timing

The VR319 monochrome monitor video timing is listed in the following tables.

Video Timing–1280 x 1024 Resolution

Horizontal frequency

Vertical frequency

Pixel frequency

Pixel period

72 Hz

77.17 kHz

72.55 Hz

130.81 MHz

7.64 ns

Refresh Rate

66 Hz

70.66 kHz

66.47 Hz

119.84 MHz

8.34 ns

Horizontal timing

Entire line

Active visible line

Blanking interval

Sync front porch

Sync pulse

Sync back porch

No. Pixels

1696

1280

416

32

160

224

µs

12.96

9.79

3.18

0.24

1.22

1.71

Vertical timing

Vertical period

(Entire Frame)

Visible raster

Blanking interval

Sync front porch

Sync pulse

Sync back porch

No. Lines

1063

1024

39

3

3

33

ms

13.78

13.28

0.506

0.039

0.039

0.428

µs

14.15

10.68

3.47

0.27

1.34

1.87

ms

15.04

15.04

0.552

0.042

0.042

0.467

Optional System Monitors 3–7

3.2 VR320 Color Monitor

The VR320 color monitor (Figure 3–4) has a direct-viewed, 485 mm

(19 in), anti-glare CRT with contrast enhancement. The monitor has a built-in tilt and swivel assembly, allowing you to adjust the screen for viewing.

Figure 3–4 VR320 Color Monitor

M A - 0 2 4 4 - 9 0 . D G

3–8 Optional System Monitors

3.2.1 Refresh Rate

The VR320 color monitor operates at a refresh rate of either 66 Hz or

72 Hz. The refresh rate is preset for the system before the monitor is shipped. If you change the monitor to another system, check the refresh rate of the new system and then set the switch on the deflection module

(Figure 3–5) and the jumpers on the power supply module (Figure 3–6) to match the new system. For additional information, refer to the VR320

Monitor Service Guide (PN EK-VR320-SV).

Figure 3–5 Refresh Rate Switch—Deflection Module

D e f l e c t i o n M o d u l e

6 6 / 7 2 H z

R e f r e s h R a t e

S w i t c h

Refresh Rate

Switch

M A - 1 0 2 7 - 8 9 . D G

L J - 0 0 5 2 5 - T I 0

Optional System Monitors 3–9

Figure 3–6 Refresh Rate Jumper—Power Supply Module

P o w e r S u p p l y M o d u l e

T o V i d e o

C a s t i n g

6 6

H z

7 2

H z

6 6 / 7 2 H z J u m p e r

Refresh Jumper

M A - 1 0 4 0 - 8 9 . D G

L J - 0 0 5 2 6 - T I 0

3–10 Optional System Monitors

3.2.2 VR320 Color Monitor Specifications

The VR320 color monitor specifications are listed next.

Power Requirements

Voltage

Frequency

88 to 132 Vac or 176 to 264 Vac auto-ranging, single phase, 3-wire

47 to 63 Hz

47 to 63 Hz

220 W maximum Power consumption

Operating Environment

Temperature range

Relative humidity

10° C to 40° C (50° F to 104° F)

10% to 95%

Maximum wet bulb = 32° C

Minimum dew point = 2°C

(noncondensing)

Physical Characteristics

Height

Width

Depth

Weight

Tilt range

Swivel range

Display - Cathode ray tube

(CRT)

Display area

45.7 cm (18.0 in)

49.5 cm (19.5 in)

45.2 cm (17.8 in)

29.0 kg (63.0 lb)

-5° forward to +15° backward

±90° (left and right)

48.3 cm (19.0 in) diagonal

Light transmission

Video input

1280 pixels horizontal x 1024 lines vertical

Approximate picture size: 34.3 cm

(13.5 in) x 27.3 cm (10.75 in) with a

5:4 aspect ratio.

58% nominal

Red (with sync) 1 Vpp, 75 ohm, ac or dc coupled

Green (with sync) 1 Vpp, 75 ohm, ac or dc coupled

Blue (with sync) 1 Vpp, 75 ohm, ac or dc coupled

Optional System Monitors 3–11

3.2.2.1 VR320 Color Monitor Video Timing

The VR320 color monitor video timing is listed in the following tables.

Video Timing–1280 x 1024 Resolution

Horizontal frequency

Vertical frequency

Pixel frequency

Pixel period

72 Hz

77.13 kHz

72.56 Hz

130.81 MHz

7.64 ns

Refresh Rate

66 Hz

70.66 kHz

66.47 Hz

119.84 MHz

8.34 ns

Horizontal Timing

Entire line

Active visible line

Blanking interval

Sync front porch

Sync pulse

Sync back porch

Vertical Timing

Vertical period

(Entire Frame)

Visible raster

Blanking interval

Sync front porch

Sync pulse

Sync back porch

No. Pixels

1696

1280

416

32

160

224

µs

12.97

9.79

3.18

0.245

1.22

1.71

No. Lines

1063

1024

39

3

3

33

ms

13.78

13.28

0.506

0.03889

0.03889

0.4279

µs

14.15

10.68

3.47

0.267

1.34

1.87

ms

15.04

14.49

0.552

0.04246

0.04246

0.4670

3–12 Optional System Monitors

3.3 VR262 Monochrome Monitor

The VR262 monochrome monitor is compatible with the VR260 monitor.

The VR262 monitor has a direct-viewed, 485 mm (19 in) diagonal antiglare screen with contrast enhancement. When connected to a host system, the VR262 monitor can display information sent to the host and information that the host system sends to you.

For installation and troubleshooting information, refer to Installing and

Using the VR262 Monochrome Monitor (PN EK-VR262-IN).

3.3.1 VR262 Monochrome Monitor Specifications

Dimensions

Height

Width

Depth

Weight

39.4 cm (15.5 in) including feet

45.5 cm (17.9 in)

39.5 cm (15.4 in)

18 kg (40 lbs)

Horizontal Rate Timing (nominal)

Frequency 54.054 kHz

Front porch

Sync pulse

Back porch

Blanking interval

Active video time

Horizontal period

Pixels displayed

160 ns

1850 ns

1690 ns

3.70 µs (maximum)

14.8 µs

18.5 µs

1024

Optional System Monitors 3–13

Vertical Rate Timing (nominal)

Frequency 60 Hz

Front porch

Sync pulse

Blanking interval

Active video time

Vertical period

Lines displayed

0 horizontal lines

3 horizontal lines

37 horizontal lines

16.0 ms

16.67 ms

864

Power

Power supply type

AC input

100 V to 120 V nominal

220 V to 240 V nominal

Power consumption

Environment

Temperature

Humidity

Transistor, switch type ac to dc converter

Switch-selectable

Single-phase, 3-wire 88 V to 132 V RMS,

47 Hz to 63 Hz line frequency

Single-phase, 3-wire 185 V to 264 V RMS,

47 Hz to 63 Hz line frequency

65 W

10° C to 40° C (50° F to 104° F)

10% to 90% maximum wet bulb of 28° C minimum dew point of 2° C

3–14 Optional System Monitors

3.4 VR299 Color Monitor

The VR299 is a 500 mm (20 in; 19 in viewable) color monitor for use on

Digital workstation products.

The monitor features are:

• In-line gun with Dynamic Astigmatism and Focus (DAF) correction

• 90 degree color CRT (P22 phosphor)

• 1024 pixel x 864 line resolution

• 60 Hz refresh

• 54.0 kHz horizontal frequency

• 0.31 mm dot pitch

• Automatic degauss on power-up

• Integral tilt and swivel

• High efficiency anti-glare bonded panel

3.4.1 VR299 Color Monitor Specifications

Physical

Height

Width

Depth

Weight

18.5 in (47.0 cm)

19.9 in (50.6 cm)

20.7 in (52.7 cm)

67.0 lbs (30.0 kg)

Timing

Vertical rate

Horizontal rate

60 Hz

54 Hz

Power

AC input DA model, 100 - 120 Vac 50/60 Hz

D3, D4 models, 200 - 240 Vac 50/60 Hz

150 W Power consumption

Environment

Operating

Temperature range

Humidity range

10° C to 40° C (50° F to 104° F)

10% to 95% non-condensing

Optional System Monitors 3–15

3.5 VRT16 Color Monitor

The VRT16 is a 406 mm (16 in), highly integrated color display monitor that is designed for displaying high-resolution graphics. The monitor features include:

• A silica coating on the screen that provides a glare-free display

• High-resolution with 1280 (horizontal) x 1024 (vertical) elements per frame, which allows for high-density color display

• Use of the 66.5 Hz non-interlace method to reduce flicker

• A display that can be turned plus or minus 45 degrees to the right or left, and can be tilted 15 degrees up or 5 degrees down

• A cylindrical screen that reduces distortion when viewed from the sides, sharpens the picture corners, and diminishes reflections

3.5.1 VRT16 Color Monitor Specifications

Physical

Height

Width

Depth

Weight

409 mm (16 in)

406 mm (16 in)

453 mm (17 in)

23.0 kg (50 lbs, 11 oz)

Power Requirements

AC input

Current

100 - 120 Vac 60 Hz

220 - 240 Vac 50 Hz

100 - 120 Vac 3.7 A max

200 - 240 Vac 2.0 A max

Environmental

Operating temperature

Nonoperating temperature

Operating humidity

Nonoperating humidity

10° C to 40° C (50° F to 104° F)

0° to 60°

10% - 80%

5% - 90%

For additional information about the VRT16 monitor, refer to the VRT16

Service Manual (PN ER-VRT16-SM).

3–16 Optional System Monitors

3.6 VRT19 Color Monitor

The VRT19 color monitor has a 474 mm (19 in) (diagonal), direct-viewed, anti-reflective coated screen with contrast enhancement. The monitor has a built-in tilt swivel assembly, allowing you to adjust the screen for viewing comfort.

The VRT19 color monitor is a highly integrated color display monitor that is designed for displaying high-resolution graphics.

The VRT19 color monitor features are the same as those of the VRT16 color monitor (refer to Section 3.5.)

3.6.1 VRT19 Color Monitor Specifications

Physical

Height

Width

Depth

Weight

474 mm (18.66 in)

480 mm (18.9 in)

505 mm (19.9 in)

32.5 kg (71 lbs, 11 oz)

Power Requirements

AC input

Current

100 - 120 Vac 60 Hz

220 - 240 Vac 50 Hz

100 - 120 Vac 3.7 A max

200 - 240 Vac 2.0 A max

Environmental

Operating temperature

Nonoperating temperature

Operating humidity

Nonoperating humidity

10° C to 40° C (50° F to 104° F)

0° C to 60° C (32° F to 140° F)

10% - 80%

5% - 90%

4

Optional System Printers

This chapter describes the optional printers that can be connected to the

VAXstation 4000 Model 60 system. The printers are:

Section 4.1

Section 4.2

Section 4.3

LA75 Companion Printer

LA210 Letterprinter

LN03 Laser Printer

4–1

4–2 Optional System Printers

4.1 LA75 Companion Printer

The LA75 Companion Printer (Figure 4–1) is a versatile high-speed dot matrix printer that can print in five modes.

• Draft

• Memo

• Near-Letter quality

• Letter quality

• Bit-Map graphics

The LA75 Companion Printer has bidirectional printing and prints at a speed of 250 characters per second. The printer is available in both serial and parallel interface models.

Figure 4–1 LA75 Companion Printer

Optional System Printers 4–3

4–4 Optional System Printers

4.1.1 LA75 Companion Printer Configuration

The LA75 Companion Printer must be configured to ensure that the printer and the system communicate with each other correctly. You may need to change some of the printer’s features and values depending on the hardware and software requirements for the system. Check the system’s documentation to determine the requirements for baud rate, data bits and parity, and protocol. Table 4–1 lists the factory set configurations for the

LA75 Companion Printer. For additional information, refer to Installing

and Using the LA75 Companion Printer (PN EK-0LA75-UG).

Table 4–1 LA75 Factory Set Configurations

LA75-S Code Version 1.0

Feature Values

Baud rate

Data bits and parity

Protocol

Form length

Character set (Digital)

Supplemental character set (Digital)

Print density (Digital)

Printer ID (Digital)

Text mode right margin (Digital)

Auto LF on CR (Digital)

Auto CR on LF (Digital)

CAN Control code (Digital)

80 or 132 Columns (Digital)

Paper out bell (Emulation)

Slashed zero (emulation)

Auto LF on CR (emulation)

Active character set (emulation)

Auto CR on LF (emulation)

Power-Up density (emulation)

LQ or NLQ (emulation)

7 4800

7 8-None

1 DEC

2 11 inches

1 U.S. ASCII

1 DEC Supplemental

1 Draft

1 LA50 ID

1 Truncate

2 NO Auto LF

2 NO Auto CR

1 Cancel control functions

1 80 Columns

2 ON

2 Zero without slash

2 NO Auto LF

1 Graphics set A

2 NO Auto CR

1 Draft

1 Select NLQ

Optional System Printers 4–5

4.1.2 LA75 Companion Printer Specifications

The LA75 Companion Printer specifications are listed in the following tables.

Power Requirements

Voltage/Frequency:

LA75-A2

LA75-A3

LA75-A4

LA75-A5

Power cord

Power receptacle

Power consumption

Operating Environment

Temperature range

Relative humidity

Physical Characteristics

Height

Width

Depth

Weight

120 Vac, 50/60 Hz

240 Vac, 50/60 Hz

220 Vac, 50/60 Hz

100 Vac, 50/60 Hz

2.0 m (6.7 ft), detachable

Non-switched, 3-prong, grounded

120 W maximum

10° C to 40° C (50° F to 104° F)

10% to 90%

12.1 cm (4.8 in)

42.7 cm (16.8 in)

34.5 cm (13.6 in)

9.5 kg (21.0 lb)

4–6 Optional System Printers

4.2 LA210 Letterprinter

The LA210 Letterprinter (Figure 4–2) is a dot-matrix, receive only (RO) printer. The printer operates in text or graphics mode. Letter quality or draft quality printing can be selected in text mode. In graphics mode, the system controls the dot printing elements.

Letter quality mode provides medium or high density printing at low speed (40 characters per second, maximum). Draft mode provides low density printing at high speed (240 characters per second, maximum).

The LA210 Letterprinter contains the courier 10 U.S. ASCII, courier 10 multinational, and VT100 line drawing character sets. Up to two fonts can be plugged into the printer’s font assembly.

Figure 4–2 LA210 Letterprinter

Optional System Printers 4–7

The LA210 Letterprinter has a standard RS232C serial interface.

Figure 4–3 shows the location of the serial interface connector. Figure 4–4 shows the location of the optional parallel interface switches.

Figure 4–3 RS232C Serial Interface Connector

4–8 Optional System Printers

Figure 4–4 Parallel Interface Switches (Optional)

Optional System Printers 4–9

4.2.1 LA210 Letterprinter Configuration

The LA210 Letterprinter configuration switches are factory set for use with most Digital systems. Check the system requirements to see if any changes are necessary. If you set the configuration switches, do not change the settings unless there is a change to the communication system. Figure 4–5 shows the location of the configuration switches. For additional information, refer to the LA210 Letterprinter User Guide (PN

EK-LA210-UG).

CAUTION

Never use a lead pencil to change the switch positions. Use a ballpoint pen or similar item.

4–10 Optional System Printers

Figure 4–5 LA210 Letterprinter Configuration Switches

Optional System Printers 4–11

4.2.2 LA210 Letterprinter Specifications

The LA210 Letterprinter specifications are listed in the next tables.

Power Requirements

Voltage 120 Vac nominal (90 to 128 Vac)

240 Vac nominal (180 to 256 Vac), switch-selectable

47 to 63 Hz

Non-switched, 3-prong, grounded

154 W maximum

Frequency

Power receptacle

Power consumption

Operating Environment

Temperature range

Relative humidity

Physical Characteristics

Height

Width

Depth

Weight

10° C to 40° C (50° F to 104° F)

10% to 90%

12.7 cm (5.0 in) without tractor

22.8 cm (9.0 in) with tractor

54.6 cm (21.5 in)

34.3 cm (13.5 in)

12.15 kg (27.0 lb)

4–12 Optional System Printers

4.3 LN03 Laser Printer

The LN03 Laser Printer is a nonimpact printer that uses a laser diode and an electrophotographic printing process. The LN03 Laser Printer prints at a rate of eight pages per minute (text only) with print quality at

300 by 300 dots per inch.

The LN03 Laser Printer (Figure 4–6) has an RS232 serial interface that allows connection to systems for text printing, and graphics by way of the sixel standard protocol.

Figure 4–6 LN03 Laser Printer

Optional System Printers 4–13

4.3.1 LN03 Laser Printer Configuration

The LN03 Laser Printer has two 6-position configuration switchpacks, located at the rear of the printer. The switchpacks are used to configure the printer operating requirements. Figure 4–7 shows the location of the switchpacks and the printer configuration factory settings. If necessary, change these settings to match the communication parameters of the system.

NOTE

Turn off power to the printer before resetting the configuration switches. The new switch settings are invoked when you turn the power on again.

CAUTION

Never use a lead pencil to change the switch positions. Use a ballpoint pen or similar item to change the switch settings.

The switchpacks are marked 1 (ON) and 0 (OFF). For additional information, refer to the LN03 Technical Manual (PN EK-OLN03-TM).

4–14 Optional System Printers

Figure 4–7 LN03 Laser Printer Configuration Switches

Optional System Printers 4–15

4.3.2 LN03 Laser Printer Specifications

The LN03 Laser Printer specifications are listed next.

Power Requirements

Voltage

Frequency

Power cord

Power requirement

Power consumption

Heat dissipation

120 Vac (85 to 132 Vac)

240 Vac (187 to 264 Vac)

50/60 Hz

3.0 m (10.0 ft) detachable

1 kVA maximum

120 Vac, 950 W maximum

240 Vac, 850 W maximum

120 Vac, 3240 Btu/h

240 Vac, 2900 Btu/h

Operating Environment

Temperature range

Relative humidity

Physical Characteristics

Height

Width

Depth

Weight

10° C to 32° C (50° F to 90° F)

20% to 80%

38.1 cm (15.0 in, with exit tray)

53.4 cm (21.0 in)

59.7 cm (23.0 in, with tray)

35 kg (77.0 lb)

D

DSW21 synchronous communications adapter, 2–5 cables, 2–7 environmental specifications, 2–8 installation, 2–7 specifications, 2–9

L

LA210 Letterprinter, 4–6 configuration, 4–9 specifications, 4–11

LA75 printer, 4–2 configuration, 4–4 specifications, 4–5

LN03 laser printer, 4–12 configuration, 4–13 specifications, 4–15

M

Model 60 System memory configuration, 2–2

MS44 memory module, 2–2 configuration, 2–2 specifications, 2–4

R

RRD42 CDROM disc drive, 1–6

SCSI ID setting, 1–6 specifications, 1–9

RX26 diskette drive, 1–10

SCSI ID setting, 1–10 specifications, 1–12

RZ23L hard disk drive specifications, 1–5 to 1–6

Index

RZ24 hard disk drive specifications, 1–5 to 1–6

RZ2x hard disk drives, 1–2

SCSI ID setting, 1–2

T

TZK10 (QIC) tape drive, 1–13

SCSI ID setting, 1–13 specifications, 1–16

V

VR262 monitor, 3–12 specifications, 3–12 to 3–13

VR299 color monitor, 3–14 specifications, 3–14

VR319 monochrome monitor, 3–2 refresh rate, 3–3 specifications, 3–5 video timing, 3–6

VR320 color monitor, 3–7 refresh rate, 3–8 specifications, 3–10 video timing, 3–11

VRT16 color monitor, 3–15 specifications, 3–15

VRT19 color monitor, 3–16 specifications, 3–16

Index 1

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project