The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmware (individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”) purchased by you and any derivatives obtained from the Software, including any copy of either. If you have executed a separate written agreement covering the Software supplied to you under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use the Software, solely as it is intended and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or reseller under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors.

The Licensee acquires no title, right or interest in the Software other than the license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which the Product was rightfully purchased except upon prior written notice to

Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is provided “AS IS” and in its present state and condition and Paradyne makes no other warranty whatsoever with respect to the Product purchased by you.

THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING

WITHOUT LIMITATION: a.

Any warranty that the Software is error-free, will operate uninterrupted in your operating environment, or is compatible with any equipment or software configurations; and b.

ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from one state or jurisdiction to another.

6. In no event will Paradyne be liable to Licensee for any consequential, incidental, punitive or special damages, including any lost profits or lost

2 March

savings, loss of business information or business interruption or other pecuniary loss arising out of the use or inability to use the Software, whether based on contract, tort, warranty or other legal or equitable grounds, even if

Paradyne has been advised of the possibility of such damages, or for any claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or otherwise transferred by the Licensee to any third party without the prior written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be terminated in the event of breach by the Licensee of any provisions of this

Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without regard to its provisions concerning conflicts of laws.

Hotwire ATM Line Cards

The Hotwire

8335, 8355, 8365, 8375, and 8385 Asynchronous Transfer Mode

(ATM) Line Cards are circuit boards mounted in an 8620 or 8820 Broadband Loop

Carrier (BLC), used to transport ATM cells at high speeds over a single twisted-pair connection.

Model 8335 supports Symmetric Digital Subscriber Line (SDSL).

Model 8355 supports ReachDSL

2.2 concurrent with POTS.

Model 8365 supports Asymmetric Digital Subscriber Line (ADSL) concurrent with POTS.

Model 8375 supports ReachDSL+, a technology that combines ADSL features and performance with the unique capabilities of Paradyne’s ReachDSL.

Model 8385 supports Single-pair High-speed Digital Subscriber Line

(SHDSL).

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.

Select Support

→ Technical Manuals.

Document Number Document Title

Primary document for this product:

8335-A2-GB20 Hotwire ATM Line Cards, Models 8335, 8355, 8365, 8375, and

8385, User’s Guide

Reference documents:

6050-A2-GZ40 Hotwire Central Office Universal POTS Splitter, Models 6050 and

7020, Installation Instructions

8335-A2-GZ40-60 March 2005 3

Document Number Document Title

6390-A2-GN10

8000-A2-GB22

Hotwire ReachDSL Modem, Model 6390 with Inline Phone Filter,

Installation Instructions

Hotwire Management Communications Controller (MCC) Card,

IP Conservative, User’s Guide

8021-A2-GB20

8021-A2-GZ40

8620-A2-GN20

8820-A2-GN20

Hotwire Shelf Concentration Module (SCM) Card User’s Guide

Hotwire Shelf Concentration Module (SCM) Card Installation

Instructions

8620 Broadband Loop Carrier Installation Guide

8820 Broadband Loop Carrier Installation Guide

To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 1-727-530-2000.

Installation Overview

Installation and configuration of the ATM Line Card consists of:

Installing the card in the BLC.

Connecting to a Main Distribution Frame (MDF).

Connecting to the DS3, OC3, E3, or T1/E1 uplink.

Providing initial unit identity information or changing existing identity information.

Configuring your unit using the Configuration Edit menus.

Be sure to register your warranty at www.paradyne.com/warranty.

Planning the Installation

Review the following list to help plan for the installation.

❑

Obtain the applicable cables; refer to Cables You Need on page 5.

❑

Make sure the chassis is installed and power is supplied to it.

❑

After the ATM Line Card is installed, there are configuration procedures that

must be performed before you can begin to use it. Refer to the Hotwire ATM

Line Cards, Models 8335, 8355, 8365, 8375, and 8385, User’s Guide for

detailed configuration procedures.

4 March

Cables You Need

The following standard cables are used with this product:

For the DSL network connection: Plug-ended Telco 50-pin cable for connection from the chassis rear connector to the MDF or other demarcation point. Refer to the 8620 or 8820 BLC Installation Guide and, if applicable, the documentation that came with your POTS splitter for more information.

For the ATM Uplink: Refer to the

Hotwire Shelf Concentration Module (SCM)

Card User’s Guide

for cable specification information.

For more information refer to Connector Pin Assignments in the Hotwire ATM Line

Cards, Models 8335, 8355, 8365, 8375, and 8385, User’s Guide .

Installing DSL Cards

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.

An ATM Line Card can be installed in, removed from, and replaced in an 8620 or

8820 BLC without disrupting service to the other cards in the chassis.

Procedure

To install the ATM Line Card:

1. Determine in which slot the unit will be installed. Verify that cards in adjacent slots have been fastened.

2. Remove the filler plate from the installation slot and store for possible later use.

8335-A2-GZ40-60 March 2005 5

3. Holding the ATM Line Card vertically with component side facing right, insert it into the top and bottom card guides.

POWER

ALARMS

A B

Fan Major Minor

SYSTEM

Alm

Test

Coll

DSL P

ORT

DSL

SYSTEM

Alm

Test

ETHERNET

Coll

MCP

POWER ENTRY MODULE

RIGHT UNIT: LINE B

WARNING! POWER MUST BE DISCONNECTED A

T THE SOURCE

POWER ENTRY MODULE

LEFT UNIT: LINE A

RIGHT UNIT: LINE B

CLOCK

SERIAL

MCC

ALARM

4 6

8 A

10 12

14 16

SERIAL

SMCM

ALARM

1 3

5 7

9 B

11 13

15 17

00-16709

CAUTION:

Do not force the unit into the slot. This could damage the backplane connectors. If the card does not seat properly, remove the card and reinstall it. If it still does not seat properly, call your service representative.

4. Slide the unit into the slot until the power and network connectors seat firmly in the mating connectors on the backplane.

The unit performs a power-on self-test. All of the LEDs turn ON and OFF briefly. When the self-test is completed successfully, the SYSTEM OK LED begins to pulse.

If the LED is not pulsing, notify your service representative.

5. Secure the unit by fastening the screws at each end of the faceplate.

Connecting to the ATM Network

The connection to the ATM network is made through the Shelf Concentration

Module (SCM), another card in the BLC. Depending on the model, the SCM

supports a DS3, OC3, E3, or T1/E1 connection. See the Hotwire Shelf

Concentration Module (SCM) Card User’s Guide for more information.

6 March

Connecting to an MDF or ADSL POTS Splitter

You can connect the ATM Line Card to an MDF or other demarcation point. Do not connect the Model 8335 or 8385 to a POTS splitter. Refer to the 8620 or 8820 BLC

Installation Guide for more information.

Refer to Connector Pin Assignments in the

Hotwire ATM Line Cards, Models 8335,

8355, 8365, 8375, and 8385, User’s Guide for pinouts of the BLC ports.

Procedure

To connect the chassis containing the unit to an MDF:

1. Determine the slot number the ATM Line Card was installed in.

2. Plug the Telco 50-pin cable into the appropriate numbered port on the back of the BLC.

3. If a ferrite and cable tie are included in the package with your ATM line card, attach the ferrite to the Telco cable, then secure it with the cable tie.

4. Dress the cable to the side the connector is nearest.

5. For the Model 8335, 8355, 8365, 8375, or 8385 with no POTS service:

— Attach the other end of the cable to the appropriate MDF or demarcation point.

For the Model 8355, 8365, or 8375 using an ADSL POTS splitter:

— Attach the other end of the cable to the XDSL interface of the Corning

Cable Systems (formerly Siecor) ADSL POTS Splitter Rack-Mount Shelf or the Hotwire 6050 Central Office Universal POTS Splitter. Refer to the document that came with the POTS splitter for the additional connections.

NOTE:

If you are connecting the Telco 25-pair, 50-pin cable to an MDF, a converter may be necessary for terminating the other end of the cable on a punchdown block before cross-connecting to an MDF.

8335-A2-GZ40-60 March 2005 7

Front Panel LEDs

The following table describes the meaning and states of the LEDs on the front panel.

SYSTEM SYSTEM SYSTEM

LOC

Alrm

Test

ATM B

LOC

Alrm

Test

LOC

Alrm

Test

DSL POR DSL POR DSL POR

POR

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

POR

9/21

10/22

11/23

12/24

POR

1/13

2/14

3/15

4/16

5/17

6/18

7/19

8/20

POR

9/21

10/22

11/23

12/24

POR

ALT BANK ALT BANK

9-16

1-8

13-24

1-12

ATM

SDSL

8335

ATM

ReachDSL

8355

G.DMT

G.Lite

8365

00-16661 02-17210 00-16719

Type

SYSTEM

LED

LED is . . . *

Green, On

Off

Green,

Pulsing

Green,

Fast Blinking

Amber, On

Indicating . . .

Card failure. System processing functions have stopped.

No power to card.

Card functioning normally.

Firmware download needed.

ATM BUS

Alrm

Test

Off

Amber, On

Off

Amber,

Fast Blinking

Off

Green,

Fast Blinking

Off

Green,

Fast Blinking

Amber, On

Alarm is present on the card. ATM interface is not being detected.

Normal operation, no alarms.

Test in progress.

Normal operation, no tests.

Self-test is in progress.

Inactive.

Cells are being transmitted.

Inactive, link down.

Cells are being received.

DSL PORT

8335

8365

24-Port

Models

ALT BANK

8335

24-Port

Models

LOC

Off

1/9–8/16

1–12

1/13–12/24

Green, On

Off

Green,

Slow Blinking

Green,

Fast Blinking

Off

9–16

1–8

13–24

1–12

Amber,

Fast Blinking

Loss Of Clock. ATM bus clock signal is not present.

Normal operation.

Good signal, unit is trained.

Port is disabled.

Port is in test, or is down.

Port is training.

The ports not currently displayed by the port status LEDs are functioning normally or are disabled.

One of the ports not currently being displayed by the port status LEDs is down, in test, or in training mode.

* Pulsing: LED turns off momentarily once per second.

Slow Blinking: LED turns on momentarily once per second.

Fast Blinking: LED turns off and on in equal duration 4 times per second.

The 8375 and 8385 front panels, not displayed, have the same LEDs and designations as the 8355.

8 March

Logging In to the MCC Card

You can log in to the management card using either a local VT100- compatible terminal or a remote Telnet connection.

After you enter your user ID and password, the system displays the Main Menu.

See the

Hotwire Management Communications Controller (MCC) Card,

IP Conservative, User’s Guide for information about selecting the unit from the

card selection screen.

Entering Card Information

After accessing your line card for the first time, use the Card Information screen to configure basic information about the card. To access the Card Information screen, follow this menu selection sequence:

Configuration

→

Card

→

Card Info (A-A-A)

Configuring the DSL Ports

You can set the rate of the DSL ports from the DSL Port Configuration screen. To access the DSL Port Configuration screen, follow this menu selection sequence:

Configuration

→

Physical Ports

→

DSL Ports (A-B-B)

Configuring the ATM Parameters

You can configure ATM parameters from the ATM Parameters screen. To access the ATM Parameters screen, follow this menu selection sequence:

Configuration

→

ATM Switch

→

ATM Parameters (A-E-A)

Configuring ATM Cross Connection

You can configure VC connections from the line card to the endpoint with the ATM

Cross Connect screen. To access the ATM Cross Connect screen, follow this menu selection sequence:

Configuration

→

ATM Switch

→

ATM Cross Connect (A-E-B)

8335-A2-GZ40-60 March 2005 9

Asynchronous Terminal Interface Menu

The following diagram shows the menu paths to the functions available through the asynchronous terminal interface.

Main

A - Configuration

A - Card

A- Card Info

B- Time/Date

C- NVRAM Clear

D- Config Loader

E- Card Reset

F- Download Code

A- Download

B- Apply

G- Spectrum Mgt 1

B - Physical Ports

A- Reserved - N/A

B- DSL Ports

C- ATM PHY Layer 4

C - Interfaces - N/A

D - Reserved - N/A

E - ATM Switch

A- ATM Parameters

B- ATM Cross Connect

C- ATM Traffic Prof

D- Clear X Connects

E- Rate Shaping 1

F - SN Configuration

A- SN Config

B- Config SN Mgt 2

B - Monitoring

A - Card Status

A- Card Info

B- Time/Date

C- Syslog

C - Applications

B - Physical Ports

A- Active List

B- Reserved - N/A

C- ATM PHY Layer 4

D- DSL Link Perf Sum

E- Reserved - N/A

F- DSL Error Stats 3

C - Interfaces - N/A

D - Reserved - N/A

E - ATM Switch

A- ATM Parameters 4

B- ATM Cross Connect

C- ATM Traffic Prof

D- ATM Aggr Stats

E- VCC Perf Stats

F- Unknown Cell Log

G- ATM Conn Status

F - SN Information

A- SN Information

B- SN Mgt 2

D - Diagnostics

A - Selftest

B - Alarms

C - ATM Ping

A- ATM Ping Config

B- ATM Ping Summary

D - Reserved - N/A 1

E - Reserved - N/A 1

F - Line Loopback 1

Applies to Model 8385 Only

Applies to Models 8335 and 8385 Only

Applies to Models 8365, 8375, and 8385 Only

Applies to Models 8335, 8365, 8375

and 8385 Only

04-17050-02

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

(Be sure to register your warranty at www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo,

FL 33773, or send e-mail to [email protected]. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.

Trademarks

Hotwire and ReachDSL are registered trademarks of Paradyne Corporation. All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or registered service marks of their respective owners.

8335-A2-GZ40-60 March 2005 11

8335-A2-GZ40-60

*8335-A2-GZ40-60*

12 March

Hello! I am an AI chatbot specifically trained to assist you with the Paradyne Hotwire 8375 Installation instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!