Topfield SRP-2100 User guide

Digital Satellite Receiver
Tota l Media Solution
SRP-2100
User Guide
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
• Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
• The mains plug, which is used as a disconnect device,
shall remain readily operable.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to a person.
The exclamation point, within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
iv
CONTENTS
Contents
Contents
1
2
3
Introduction
1.1 Features . . . . . . . . . . . . .
1.2 Controlling the digital receiver
1.2.1 The front panel . . . . .
1.2.2 The remote control . . .
1.3 What is the common interface?
iv
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
3
4
5
8
Setup
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . .
2.2 Safety precautions . . . . . . . . . . . . . . . . . .
2.3 Rear panel connections . . . . . . . . . . . . . . . .
2.4 Connecting up your digital receiver . . . . . . . .
2.4.1 Connecting the antenna . . . . . . . . . . .
2.4.2 Connecting to your television set . . . . .
2.4.3 Connecting to your video cassette recorder
2.5 Inserting batteries in the remote control . . . . . .
2.6 Switching on for the first time . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
10
10
11
13
15
15
16
19
19
20
Service Search
3.1 Searching broadcasting services . . . . .
3.1.1 Configuring LNB settings . . . .
3.1.2 Configuring DiSEqC 1.2 settings
3.1.3 Configuring USALS settings . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
21
21
22
24
25
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CONTENTS
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
27
30
31
32
32
33
Preference Settings
4.1 Language settings . . . . . . . . . . . . . .
4.1.1 Menu language . . . . . . . . . . .
4.1.2 Subtitle language . . . . . . . . . .
4.1.3 Audio language . . . . . . . . . .
4.2 Video and audio settings . . . . . . . . . .
4.2.1 High definition television . . . . .
4.2.2 Colour model . . . . . . . . . . . .
4.2.3 Video cassette recorder . . . . . .
4.2.4 Television aspect ratio . . . . . . .
4.2.5 Audio mode . . . . . . . . . . . .
4.3 Local time setting . . . . . . . . . . . . . .
4.4 Parental control . . . . . . . . . . . . . . .
4.5 Recording Settings . . . . . . . . . . . . .
4.6 Playback Settings . . . . . . . . . . . . . .
4.7 Adjusting the On-Screen Display . . . . .
4.8 Front Display Settings . . . . . . . . . . .
4.9 To use MediaHighway programme guide
4.10 Adjusting a size of picture in picture . . .
4.11 Slideshow Settings . . . . . . . . . . . . .
4.12 Standby mode Setting . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
34
34
35
35
36
36
37
37
38
39
39
42
43
44
45
46
47
47
47
48
Daily Usage
5.1 Volume control . . . . . . . . . . . . . . .
5.2 Watching television . . . . . . . . . . . . .
5.2.1 The services list . . . . . . . . . . .
5.2.2 The favourite services list . . . . .
5.2.3 Viewing programme information
5.2.4 Selecting audio tracks . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
49
49
49
49
52
53
54
3.2
3.3
3.4
3.5
3.6
4
5
3.1.4 Searching services .
Copying services . . . . . .
Editing the transponder list
Resetting to factory settings
Resetting to user settings . .
Clearing the services list . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
v
vi
CONTENTS
.
.
.
.
.
.
54
54
55
55
56
57
6
Editing Services
6.1 Editing the services list . . . . . . . . . . . . . . . . . . . . . . .
6.2 Editing the favourite list . . . . . . . . . . . . . . . . . . . . . .
6.3 How to use the on-screen keyboard . . . . . . . . . . . . . . .
59
59
61
63
7
Recording and Playing
7.1 Recording a programme . . . . . . . . . . . . . . . . . . . .
7.1.1 Instant recording . . . . . . . . . . . . . . . . . . . .
7.1.2 Recording Reservation . . . . . . . . . . . . . . . .
7.1.3 Scheduling recordings using the programme guide
7.1.4 Recording a time-shifted programme . . . . . . . .
7.1.5 Recording a pay service programme . . . . . . . . .
7.2 File archive . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1 To delete a recording . . . . . . . . . . . . . . . . . .
7.2.2 To sort recordings . . . . . . . . . . . . . . . . . . .
7.2.3 To lock a recording . . . . . . . . . . . . . . . . . . .
7.2.4 To rename a recording . . . . . . . . . . . . . . . . .
7.2.5 To make a new folder . . . . . . . . . . . . . . . . .
7.2.6 To move a recording to another folder . . . . . . . .
7.3 Playing back a recording . . . . . . . . . . . . . . . . . . . .
7.3.1 To navigate using the progress bar . . . . . . . . . .
7.3.2 To play in slow motion . . . . . . . . . . . . . . . .
7.3.3 To play in fast motion . . . . . . . . . . . . . . . . .
7.3.4 To make a bookmark . . . . . . . . . . . . . . . . . .
7.3.5 To play back a recording repeatedly . . . . . . . . .
7.3.6 To play back recordings in sequence . . . . . . . . .
7.3.7 To play back a scrambled recording . . . . . . . . .
7.4 Editing a recording . . . . . . . . . . . . . . . . . . . . . . .
7.5 Copying a recording . . . . . . . . . . . . . . . . . . . . . .
64
65
66
67
70
70
71
72
72
73
73
73
74
74
74
75
76
76
76
77
77
78
78
79
5.3
5.4
5.5
5.6
5.2.5 Selecting subtitle tracks . . . .
5.2.6 Viewing teletext . . . . . . . .
Viewing electronic programme guide
Watching multifeed programme . . .
Using time shift . . . . . . . . . . . . .
Using picture in picture . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CONTENTS
7.6
8
9
vii
Formatting the hard disk . . . . . . . . . . . . . . . . . . . . . . 80
Special Features
8.1 Playing back MP3 files . . . . . . . . . . . . . . . . . .
8.2 Playing back video files . . . . . . . . . . . . . . . . .
8.3 Viewing graphic files . . . . . . . . . . . . . . . . . . .
8.4 Copying files . . . . . . . . . . . . . . . . . . . . . . .
8.4.1 To copy a file to an external hard disk drive .
8.4.2 To copy a file from an external hard disk drive
8.5 Playing back contents of YouTube . . . . . . . . . . .
8.6 Sharing image files by Flickr . . . . . . . . . . . . . . .
8.7 Weather . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8 Network Game . . . . . . . . . . . . . . . . . . . . . .
8.8.1 To use the wireless keyboard . . . . . . . . . .
8.8.2 Battle Tank Single Mode . . . . . . . . . . . . .
8.8.3 Battle Tank Network Mode . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
81
81
82
82
83
83
84
84
85
87
87
87
88
93
Accessing to The Digital Receiver via The Internet
9.1 Configuring the router . . . . . . . . . . . . . . . . . . . .
9.1.1 To access within the local area network . . . . . .
9.1.2 To access over the Internet . . . . . . . . . . . . .
9.2 Configuring the network settings on the digital receiver .
9.3 Accessing the web server . . . . . . . . . . . . . . . . . .
9.4 Accessing the FTP server . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
94
95
95
96
97
98
100
.
.
.
.
.
.
.
.
.
.
.
.
.
10 Firmware Update
10.1 Checking the firmware information . . .
10.2 From a USB memory . . . . . . . . . . . .
10.3 From the firmware server via the network
10.4 Over the air . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
103
103
104
104
106
A Universal Remote Control
A.1 TV codes list . . . . . . .
A.2 DVD codes list . . . . .
A.3 Audio system codes list
A.4 Additional codes list . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
107
110
127
129
131
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
viii
CONTENTS
Index
132
1
Chapter 1
1
Introduction
Congratulations on buying a SRP - 2100. The SRP - 2100 allows
you to view and record digital TV programmes easily.
And the SRP - 2100 digital receiver is fully compliant with the
international Digital Video Broadcasting (DVB) standard, and
thus able to receive digital broadcasts of that standard.
For its operation you need an antenna which must be installed
appropriately.
NOTE
In general, we equate a channel with a frequency. However,
unlike analogue broadcasts, digital broadcasts are not all assigned to their own frequencies; instead, multiple television
broadcasts are transmitted through a single frequency. The frequency in digital broadcasting is usually called transponder. To
reduce confusion in this manual, the word service is preferably
used than channel as a term to indicate one television or radio
broadcast.
2
Introduction
1.1
Features
The SRP - 2100 has plenty of features as follows:
• Supports DiSEqC 1.0, DiSEqC 1.1, DiSEqC 1.2 and USALS.
• Can store up to 7,000 television and 3,000 radio services.
• You can edit the services list.
• You can create favourite lists of your favourite services.
• You can see information about the current television or
radio programme.
• Have electronic programme guides that provide an overview of scheduled programmes.
• You can record one service while you are currently watching another.
• You can record many programmes using a hard disk
drive with large storage capacity.
• The time shift is available on the SRP - 2100. You can
pause the programme that you are watching and resume
it again at a later time. Then you can quickly go to any
part of the current programme by fast forward or backward search.
• If you have an external hard disk drive connected to
the digital receiver via the USB or eSATA ports, you can
record television programmes into it. You can use the
external hard disk drive as fast as the built-in hard disk
drive with eSATA port.
• You can play back DivX and MP3 files and view image
files in JPG format.
• You can play a network game with other players.
• You can play back various contents of the YouTube via
the network.
1.2 Controlling the digital receiver
1.2
3
Controlling the digital receiver
You can operate the digital receiver with the remote control or
the buttons on the front panel.
NOTE
When the digital receiver is off but plugged into a wall outlet,
we say that it is in standby mode; on the other hand, when it is
on, it is in operation mode. Even when you are not using the
digital receiver, you should keep it plugged into a wall outlet
to be in standby mode so that it can perform timer events at
any time.
1
4
Introduction
1.2.1
The front panel
The front panel of the digital receiver has buttons to control
the digital receiver, specific lamps and a display to indicate its
status. The following indicates what they mean.
button switches the digital receiver between standby
mode and operation mode.
Front display shows the current time in standby mode, and
displays the current service in operation mode.
MENU / OK button displays the main menu. It is also used
to return to the previous menu from a submenu.
ca
CHANNEL ,
buttons switch to previous or next service.
They are also used to navigate in menus and interactive
screens.
bd
VOLUME ,
buttons decrease or increase the volume.
They are also used to change values for menu options.
The lamp on the left side of the
button lights up in red
in standby mode when you set the Standby Mode option to
Passive. See § 4.12 for more details.
Pull the right edge of the front panel to open
the flap. There are USB ports on the front
panel to connect to an external hard disk
drive or memory stick.
1.2 Controlling the digital receiver
1.2.2
5
The remote control
1
button switches the digital receiver between standby
mode and operation mode.
2
mutes the sound. Press
again to switch it back on.
3
TV switches the remote control to television mode to operate your television.
4
PVR switches the remote control to receiver mode to operate the digital receiver.
5
AUX switches the remote control to operate your audio system.
6
DVD switches the remote control to DVD mode to operate
your DVD player.
41
7
Numeric buttons are used to
enter a service number for
service change or to specify
values for menu options.
8
switches between the current service and the previously viewed one.
9
displays the service information box. It is also used
to display more information about a programme.
10
VOLUME+ , VOLUME− buttons decrease or increase the
volume.
1
6
Introduction
11
CHANNEL+ , CHANNEL− buttons switch to previous or
next service.
12 OK displays the services list. See § 5.2.1 for more details.
It is also used to select a menu item.
13 Navigation buttons are used to navigate in menus or to
change values for menu options.
14 MENU displays the main menu. It is also used to return
to the previous menu from a submenu.
15 GUIDE displays the electronic programme guide.
16 EXIT is used to exit a menu or to hide on-screen info.
17
is used to display the list of recorded programmes
that are stored on the built-in hard disk drive. See § 7.2
for more details.
18 F1 is used to display or hide the sub-picture. See § 5.6
for information about picture-in-picture.
19 F2 is used to make a bookmark during playback or time
shift.
20 F4 is used to edit a recording.
21 F3 is used to jump to next bookmark position.
22
Option has different functions per menu.
23
24
25
is used to select a subtitle track.
is used to select an audio track and a sound mode, or
a video track of multifeed programme.
displays teletext.
26 VF changes video resolution. See § 4.2.1 for more details.
27 AR changes aspect ratio. See § 4.2.4 for more details.
28
switches between television services and radio services.
1.2 Controlling the digital receiver
7
29
is used to set a sleep timer in 10 minute increments.
30
is used to start recording.
31
is used to stop playback, to stop recording, or to jump
back to live service from time-shifted service.
32 M switches the output of the TV SCART socket between
the digital receiver and the device connected to the VCR
SCART socket. See § 4.2.3 for more details.
33 SAT displays the satellites list with their services list. It is
also used to swap the sub-picture with the main picture.
See § 5.6 for more details.
34
is used to start reverse playback. Subsequent presses
increase the rewind speed.
35
pauses live television or playback of a recorded programme.
36
is used to start fast motion playback. Subsequent
presses increase the playback speed.
37
resumes normal playback speed, or displays the
progress bar for navigation on playback or time shift.
To play a recorded programme, see button 17.
38
changes the position of sub-picture counterclockwise.
It is also used to jump back to beginnng of recording
during a playback.
39
is used to start slow motion playback. Subsequent
presses change the playback speed.
40
changes the position of sub-picture clockwise. It is
also used to jump to end of recording during a playback.
41
is used to specify a block for editing or for repeated
playback.
1
8
Introduction
The F1 , F2 , F3 , F4 and Option buttons have additional different functions per menu besides their own function. They will
be guided by on-screen help.
NOTE
When using the remote control, point it at the remote sensor
on the front panel of the digital receiver.
1.3
What is the common interface?
Some broadcasts are scrambled so
that only paid subscribers can enjoy
them. Scrambled services can only
be viewed with a Conditional Access
Module (CAM) and a subscription
card belonging with the scrambling
system.
Common Interface (CI) is the slot
on a digitial receiver into which a
conditional access module may be
inserted. The front of the digital receiver has two common interfaces.
To watch a pay service, you should take the following steps:
1. Purchase a conditional access module and a subscription
card for the pay service you want to watch.
2. Insert the subscription card into the conditional access
module.
3. Insert the conditional access module into a common interface on the front of the digital receiver.
1.3 What is the common interface?
9
To view the information about
the module and subscription
card which is inserted into the
digital receiver, select the Information > Common Interface
menu.
You should see a screen like the
left figure.
NOTE
If you wish to watch two pay services using the picture-inpicture feature, you have to set the Descramble Multiple Services option to Enable, and then install the dedicated CAM
which is able to descramble two pay services simultaneously.
See § 5.6 for the picture-in-picture feature.
1
10
Setup
Chapter 2
Setup
2.1
Unpacking
Before going any further, check that you have received the
following items with your digital receiver.
•
•
•
•
•
Remote control unit
Two batteries for the remote control (AAA 1.5 V)
One HDMI cable
Wireless keyboard
A copy of this user guide
NOTE
The wireless keyboard is only for the Battle Tank. See § 8.8.
NOTE
These items may vary according to your local area.
2.2 Safety precautions
2.2
11
Safety precautions
Please read carefully the following safety precautions.
• The mains power must be 90 to 250 volts. Check it before
connecting the digital receiver to the mains socket. For
the power consumption of the digital receiver, refer to
Table 2.1.
• The mains outlet should be near the equipment. Do not
run an extension lead to the unit.
• Do not expose the digital receiver to any moisture. The
digital receiver is designed for use indoors only. Use dry
cloth when cleaning the digital receiver.
• Place the digital receiver on a firm and level surface.
• Do not place the digital receiver close to heat emitting
units or in direct sunlight, as this will impair cooling.
Do not lay any objects such as magazines on the digital receiver. When placed in a cabinet, make sure there
is a minimum space of 10 centimetres around it. For
the physical specification of the digital receiver, refer to
Table 2.2.
• Protect the power cord from being walked on or pinched.
If the cord is damaged, stop using the digital receiver
and replace the cord.
• Never open the digital receiver casing under any circumstances, the warranty will be void.
• Use only one USB port of the receiver while using a
common interface. The receiver may not recognize all the
devices because the power supply of the receiver cannot
provide enough power for all the devices.
• Refer all servicing to a qualified service technician.
2
12
Setup
• The top and bottom panel come already assembled. If
they become separated, see the following instructions
how to reattach.
1. Hook the top panel in the direction shown .
2. Push the top panel down so
that it is completely fixed.
3. Turn the digital receiver upside down to attach the bottom
panel.
4. Attach the bottom panel in the
same way as the top panel.
Table 2.1: Power specifications
Input voltage
Power consumption
90 to 250 V AC, 50/60 Hz
60 W at maximum in operation
1 W in passive standby
Table 2.2: Physical specifications
Size
Weight
Operating temperature
Storage relative humidity
340× 82× 258 mm
3.8 kg
0 to 45 °C
5 to 90 %
2.3 Rear panel connections
2.3
13
Rear panel connections
The SRP - 2100 has a wide range of connections on the back.
2
Check what connections your television set has in comparison
with the digital receiver.
1 LNB 1 IN
Satellite broadcasting signal input socket for
the first tuner.
2 LNB 1 OUT Satellite broadcasting signal output socket
through the first tuner.
3 LNB 2 IN
Satellite broadcasting signal input socket for
the second tuner.
4 LNB 2 OUT Satellite broadcasting signal output socket
through the second tuner.
5 S/PDIF COAXIAL Coaxial type of Dolby Digital output
socket for the audio system.
6 S/PDIF OPTICAL Optical type of Dolby Digital output
socket for the audio system.
7 VCR
Audio and video input/output socket for the
video cassette recorder or suchlike.
8 Y/Pb/Pr
Component video output sockets for the television set. (blue/green/red)
9 TV
Audio and video output socket for the television set.
14
Setup
10 AUDIO L/R Stereo audio output sockets for the television
set or the audio system. (white/red)
11 VIDEO
Composite video output socket for the television set. (yellow)
12 HDMI
Audio and video output socket for the high
definition television set.
13 eSATA
eSATA port for connecting to an external
hard disk drive.
14 LAN
Local area network port. See § 9.2.
15 USB
USB port for firmware update and data transfer.
16 ON/OFF
Power on/off switch. Before using this digital receiver, you have to turn on the switch
first.
Table 2.3: Connectors specifications
HDMI
TV
VCR
YPbPr
VIDEO
AUDIO
S/PDIF
LAN
USB
eSATA
High definition video output
Left & right audio output
Dolby Digital audio output
CVBS/YUV/RGB video output
Left & right audio output
CVBS video output
Left & right audio output
CVBS/S-Video/RGB video input for bypass
Left & right audio input for bypass
Component video (YUV) output
Composite video (CVBS) output
Left & right audio output
Dolby Digital audio output
10/100 Ethernet
2.0 Host (5 V DC, 500 mA)
External hard disk drive connector
2.4 Connecting up your digital receiver
2.4
15
Connecting up your digital receiver
There are several ways to set up the digital receiver. Set up the
digital receiver suitably to your television and other appliances.
If you have any problem with your setup or need help, contact
your dealer.
2.4.1
Connecting the antenna
Whatever sort of connection you have between the digital receiver and the television,
you need to connect the digital receiver to
your television antenna so that it can receive
digital television services.
Connect the antenna cable to the LNB 1 IN
connector on the back panel of the digital
receiver.
Also, you must ensure that there is a connection to both the LNB 1 IN and LNB 2 IN
connectors on your digital receiver, so that
both tuners work properly.
Normally you do that by using a loop cable to link from the
LNB 1 OUT connector to the LNB 2 IN connector.
If you have two antennas without DiSEqC switch, then you
have to connect a cable from the other antenna directly to the
LNB 2 IN connector rather than using the loop cable. If you
have another digital receiver, you may link it from the LNB 2
OUT connector.
NOTE
The digital receiver can supply a current of 500 milliampere at
maximum for antenna devices including LNB, DiSEqc switch
and antenna rotor through each antenna input connection separately but not simultaneously. If there are too many antenna
2
16
Setup
devices to be supplied with power through antenna input connections simultaneously for a long time, your LNBs may lack
power to operate. So it is recommended linking the LNB 1
OUT connector to the LNB 2 IN connector with a loop cable
even though the digital receiver is designed to operate over
two antennas alternatively.
NOTE
Perhaps you are expecting that the satellite antenna could simultaneously catch all frequencies coming from a satellite and
send them to the digital receiver. However, the satellite antenna only sends the frequencies that it can catch with the LNB
frequency and polarisation specified by the digital receiver. So
if you have linked from the LNB 1 OUT connector to the LNB 2
IN connector, you would have some limitations in using some
features such as dual recording. Likewise, if you have another
digital receiver linked from the LNB 2 OUT connector, you can
only use it limitedly. See § 3.1 for more details.
2.4.2
Connecting to your television set
For all the following connections of the digital receiver, we
recommend you use the first connector to get the best picture
quality. If your television does not have a matching connector,
then use the next connector in the following order for a better
picture quality.
1. HDMI connector (HDMI)
2. SCART connector (TV)
3. Component connector (YPbPr)
4. Composite connector (VIDEO)
You should configure audio and video settings after connecting
up the digital receiver. See § 4.2 for a detailed description.
2.4 Connecting up your digital receiver
17
To use the HDMI connector
If you have a high definition television set,
you should use a HDMI cable for the best
results. Plug one end of the cable into the
HDMI socket on the digital receiver, and plug
the other end into the matching socket on
your television. In this case, you do not have
to make audio connection because the HDMI
connector can output stereo audio or Dolby
Digital audio.
To use the SCART connector
For the best results with a standard television
set, you should use a SCART cable. Plug one
end of the cable into the TV socket on the
digital receiver, and plug the other end into a
free SCART socket on your television.
Some televisions have inputs via S-Video or
Component connectors rather than SCART.
If you have such a television, use an appropriate conversion cable to link the TV socket on the digital receiver to the matching
socket on your television.
If you connect with a standard SCART cable, you do not have
to make audio connection because the SCART connector can
output stereo audio. But if you use a conversion cable, such as
SCART-to-Component, you have to make audio connection.
NOTE
You cannot view high definition video with a SCART connector.
2
18
Setup
To use the component video connector
You need to obtain a component video cable
(RCA cable) to use the component video connector. Plug one ends of the cable into the Y
(green), Pb (blue) and Pr (red) sockets on the
digital receiver, and plug the other ends into
the matching sockets on your television.
To use the composite video connector
NOTE
You cannot view high definition video with a
composite video connector.
You need to obtain a composite video cable
(RCA cable) to use the composite video connector. Plug one end of the cable into the
VIDEO (yellow) socket on the digital receiver,
and plug the other end into the matching
socket on your television.
To make the audio connection
You need to obtain an audio cable (RCA cable) to connect the audio connectors. Plug
one end of the cable into the AUDIO L (white)
and AUDIO R (red) sockets on the digital receiver, and plug the other end into the matching sockets on your television or audio system.
2.5 Inserting batteries in the remote control
19
To enjoy Dolby Digital audio, your television or audio system must be able to decode
Dolby Digital audio, and you need to obtain a
S/PDIF cable. If you want to use the COAXIAL connector, prepare a coaxial S/PDIF cable
(RCA cable); otherwise, to use the OPTICAL
connector, prepare an optical S/PDIF cable.
Plug one end of the cable into the S/PDIF
socket on the digital receiver, and plug the
other end into the matching socket on your
audio system.
2.4.3
Connecting to your video cassette recorder
The digital receiver can also output video to another appliance
such as a video cassette recorder through an auxiliary SCART
connector.
You need to obtain a SCART cable to use the
auxiliary SCART connector. Plug one end of
the cable into the VCR socket on the digital receiver, and plug the other end into the matching socket on your video cassette recorder or
suchlike.
2.5
Inserting batteries in the remote control
Open the battery compartment by removing the lid, and then
insert the batteries observing the polarity, which is marked on
the base of the battery compartment.
If the digital receiver no longer reacts properly to remote control commands, the batteries may be flat. Be sure to remove
used batteries. The manufacturer accepts no liability for the
damage resulting from leaking batteries.
2
20
Setup
NOTE
Batteries, including those which contain no heavy metals, may
not be disposed with other household wastes. Please dispose
of used batteries in an environmentally sound manner. Find
out the legal regulations which apply in your area.
2.6
Switching on for the first time
Now that you have your digital receiver connected, you should
plug it into a mains socket. Ensure that your television set is
turned on and on the correct AV channel, so that you will be
able to see the display from the digital receiver.
And press the
button on top left corner on the remote control. After about 10 seconds you may see a picture displaying a
menu. If you cannot see a picture, try pressing the VF button
on the remote control. If after several tries you still get no
picture, check that the television is set to the correct input.
If you still cannot see a picture, you may need to temporarily
connect the composite video connector (VIDEO) to your television set so that you can see the on-screen menus in order to
configure the video settings.
21
Chapter 3
Service Search
3
After connecting up your digital receiver, you need to search
for the available TV and radio services.
NOTE
If there are no services stored, you will be unable to access
some menu options.
3.1
Searching broadcasting services
You can use this digital receiver with both fixed antenna and
motorized antenna. When using a antenna, you have to configure antenna settings according to your antenna system in the
following order:
1. Configure LNB settings. (Refer to § 3.1.1.)
2. Set the position of your desired satellites if you have
a motorized antenna. You can control the antenna in
DiSEqC 1.2 mode or USALS mode. Refer to § 3.1.2 for
DiSEqC 1.2, and refer to § 3.1.3 for USALS.
3. Perform a service search.
22
Service Search
3.1.1
Configuring LNB settings
There are two large frequency bands for satellite broadcasts.
One is C band which ranges approximately from 4 to 6 GHz.
The other is Ku band which ranges approximately from 12 to
18 GHz.
The LNB (Low Noise Block converter)
is used to take a wide band of relatively
high frequencies, amplify and convert
them to similar signals that is carried
at a much lower frequency, which is
called Intermediate Frequency (IF).
High frequencies from satellites are
converted into 950 to 2150 MHz by a
LNB.
Select the Installation > LNB Setting menu to configure the LNB
settings. You should see a screen
like the left figure.
Pressing the OK button on the Satellite Name option displays
the satellite list in alphabetic order. Select the satellite toward
which your antenna is set to face.
You have to specify which tuner is connected to your selected
satellite. If it is LNB 1 IN, set the Tuner Select option to Tuner
1; otherwise, set this option to Tuner 2.
3.1 Searching broadcasting services
23
If you have connected the LNB 1 OUT and LNB 2 IN with a
loop-through cable, then set the Connection Type option to
Loop Through; otherwise, set this option to Separated.
NOTE
Both the LNB 1 IN and LNB 2 IN sockets should be connected
to your antennas either directly or via the loop-through cable.
If you have connected only one socket, some functions such as
dual recording may not work.
The digital receiver has a database of broadcasting satellites
and their transponders, including the following information:
satellite position, frequency range, symbol rate, polarization
and LNB frequency corresponding to the frequency range. So
you might not have to specify the LNB Frequency option. However, if you have selected the Other entry at the Satellite Name
option to specify a satellite that is not in the satellite list, you
might have to fill in the correct LNB frequency. The absolute
difference between a broadcasting frequency and its LNB frequency must be within 950 to 2150 MHz. For example, if the
frequency band of your desired satellite ranges from 3660 to
4118 MHz, you have to set the LNB Frequency option to 5150
MHz.
The LNB has to be supplied with electric power to operate. Set
the LNB Power option to On if it does not have any other power
supply.
If you use a dual LNB or two antennas which is connected to
the 22 kHz tone switch box, set the 22 kHz option to ON.
The digital receiver is designed to be compatible with DiSEqC
(Digital Satellite Equipment Control) switches. It is possible
to connect several antennas to one digital receiver by using
DiSEqC switches. A DiSEqC 1.0 switch allows switching up to
four satellite sources and a DiSEqc 1.1 switch allows switching
up to 16 satellite sources.
3
24
Service Search
Set the DiSEqC 1.0 option and the DiSEqC 1.1 option according to your antenna configuration.
For example, to select the antenna connected to the A5 input in the left figure,
set the DiSEqC 1.1 option to 2 of 4 and
the DiSEqC 1.0 option to 1 of 4. If you
have a mini DiSEqC 1.0 switch which
has only two inputs, you should set the
DiSEqC 1.0 option to Mini A instead of
1 of 4.
3.1.2
Configuring DiSEqC 1.2 settings
Your motorized antenna will turn toward your desired satellites
horizontally by DiSEqC 1.2.
When you switch to an service, if the service is
provided by a satellite other than current one,
it will take longer time than usual because the
antenna has to turn to its position.
To use the DiSEqC 1.2 protocol,
select the Installation > Motorized DiSEqC 1.2 menu.
You should see a screen like the
left figure.
At first you have to set the Motorized DiSEqC 1.2 option to Enable.
3.1 Searching broadcasting services
25
To get the correct position of your desired satellite, perform the
following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Select the tuner that is connected to the motorized antenna at the Tuner Select option.
3. Set the DiSEqC Command Mode option to User.
4. Set the Motor Control option to Goto. Then the antenna
will turn toward your selected satellite by the position
data that the digital receiver has.
5. If the receiving quality, which is displayed at the top
right of the screen, is not good, tune the antenna finely
with the Movement option. If you set it to 2(E), the antenna will move to the east by two degrees. At this time
you had better check the receiving quality of every transponder and choose the best one at the Transponder (or
Frequency) option. It will be helpful to your fine tuning.
6. Finally set the Motor Control option to Store to save the
tuned position when the receiving quality is the best.
There are more motor control options for installers, but this
guide does not describe them. If you are an installer, refer them
to the manual of the STAB rotor.
3.1.3
Configuring USALS settings
USALS (Universal Satellite Automatic Location System), also
known as DiSEqC 1.3, calculates the positions of all available
satellites from your location. Compared to DiSEqC 1.2, it is no
longer required to manually search and store every satellite
position. Just pointing to a known satellite position is enough.
This position will act as a central point. The USALS will then
calculate positions of visible satellites.
3
26
Service Search
To use the USALS protocol, select the Installation > USALS
Setting menu.
You should see a screen like the
left figure.
At first you have to set the Motorized DiSEqC 1.3 option to Enable.
To get every satellite position calculated, perform the following
steps:
1. Choose your desired satellite at the Satellite Name option.
2. Select the tuner that is connected to the motorized antenna at the Tuner Select option.
3. Enter your location to the My Longitude option and the
My Latitude option with the
,
and numeric buttons.
4. Enter the position of your selected satellite to the Satellite
Angle option if it is not correct.
5. Select the Goto the position option; then the antenna
will turn toward your selected satellite as calculating its
position.
6. If the receiving quality, which is displayed at the top
right of the screen, is not good, then tune the antenna
finely with the Move option. The changed position is
automatically saved. At this time you had better check
the receiving quality of every transponder and choose
the best one at the Transponder (or Frequency) option. It
will be helpful to your fine tuning.
3.1 Searching broadcasting services
3.1.4
27
Searching services
To perform service search, select the Installation > Searching
menu.
You should see a screen like the
left figure.
3
There are four service search methods:
• Searching every service of a satellite.
• Searching every service of a transponder.
• Searching one service of a transponder.
• Searching every service of a SMATV (Satellite Master
Antenna Television) system.
Searching every service of a satellite
To search every service of a satellite, perform the following
steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to Auto.
3. If you set the Network Search option to On, the digital
receiver will check up the up-to-date channel information
as searching services, but it takes rather longer time.
Searching every service of a transponder
To search every service of a transponder, perform the following
steps:
28
Service Search
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to Manual... and press the
OK button.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to the polarization of your
desired transponder.
6. Set the Modulation option to the modulation type of your
desired transponder. If your desired transponder has
high definition broadcasts, you should set this option to
DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC option
and the Pilot option will become enabled. You should
also set these options correctly.
7. If you set all options correctly, press the MENU button to
save the settings.
8. If you set the Network Search option to On, the digital
receiver will check up the up-to-date channel information
as searching services, but it takes rather longer time.
NOTE
You may get transponder information from a satellite magazine
or web site such as http://www.satcodx.com or http://www.
lyngsat.com.
Searching one service of a transponder
To search one service of a transponder, perform the following
steps:
1. Choose your desired satellite at the Satellite Name option.
3.1 Searching broadcasting services
29
2. Set the Search Mode option to Advanced... and press the
OK button.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to the polarization of your
desired transponder.
6. Set the Modulation option to the modulation type of your
desired transponder. If your desired transponder has
high definition broadcasts, you should set this option to
DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC option
and the Pilot option will become enabled. You should
also set these options correctly.
7. Specify the packet identifiers of your desired service at
the PID option with the numeric buttons. A packet identifier is used to verify audio and video streams.
8. If you set all options correctly, press the MENU button to
save the settings.
Searching every service of SMATV system
To search every service of a SMATV system, if the digital receiver is connected to it, perform the following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to SMATV... and press the
OK button.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
3
30
Service Search
5. If you set all options correctly, press the MENU button to
save the settings.
You can search pay services as well as free services as follows:
• To search only free services, set the FTA/Scrambled option
to FTA only.
• To search only pay services, set it to CAS only.
• To search both free services and pay services, set it to FTA
+ CAS.
To start service search, select the Start Search item; then a list
box appears, in which found services will be listed. When it
has completed, press the OK button to save found services.
To stop at any time or to exit without saving, press the EXIT button.
3.2
Copying services
The digital receiver maintains a separate services list with each
tuner. If a certain service is registered on only one tuner, it may
be unable to watch one service while recording. You can copy
one tuner’s services list to the other tuner to avoid such an
inconvenience.
To copy the services list, select the Installation > Services Copy
menu. There are three copy options as follows:
• To copy the first tuner’s services list to the second tuner,
select the Tuner 1 to Tuner 2 option.
• To copy the second tuner’s services list to the first tuner,
select the Tuner 2 to Tuner 1 option.
• To copy reciprocally, select the ALL option.
3.3 Editing the transponder list
3.3
31
Editing the transponder list
You can change satellite information.
Select the Installation > SAT/TP
Edit menu. You should see a
screen like the left figure.
3
To change the information of a satellite entry, perform the
following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
3. Change the Polarization option to the polarization of your
desired transponder.
4. Change the Modulation option to the modulation type of
your desired transponder. If your desired transponder
has high definition broadcasts, you should set this option
to DVB-S2 QPSK or DVB-S2 8PSK. Then the FEC option
and the Pilot option will become enabled. You should
also set these options correctly.
5. To change a satellite entry’s name, select your desired
entry at the Satellite Name option and select the SAT
Name Edit option. Then the on-screen keyboard appears.
Change the name and save it.
See § 6.3 for how to use the on-screen keyboard.
32
Service Search
6. Select the Save option and press the OK button to save
the changes. To stop at any time or to exit without saving,
press the EXIT button.
3.4
Resetting to factory settings
The digital receiver maintains the following data:
•
•
•
•
•
Satellite list
Services list
Favourite list
Timer list
Preference settings
You can reset all data of the digital receiver. To do that, select
the Installation > System Recovery > Factory Setting menu,
and then you get asked for confirmation. If you select Yes,
service entries, favourite entries and timer events will all be
deleted, and preference options will be reset to the manufacturer’s factory settings.
NOTE
The factory reset does not delete any recorded programmes.
NOTE
After performing the factory reset, you have to search services
again.
3.5
Resetting to user settings
You can store your own data including the following:
• Satellite list
• Services list
3.6 Clearing the services list
33
• Favourite lists
• Preference settings
Also you can restore them at any time.
To store your data, select the Installation > System Recovery >
Store System Data menu; then you get asked for confirmation.
If you select Yes, your data will be stored. Whenever you store
your data, they are all overwritten.
To restore your data, select the Installation > System Recovery > Recover System Data menu; then you get asked for
confirmation. If you select Yes, your data will be restored.
You can also store your data to an external hard disk drive.
To store your data to an external hard disk drive, select the
Installation > System Recovery > Export System Data menu;
then you get asked for confirmation. If you select Yes, your
data will be stored.
To restore your data from an external hard disk drive, select the
Installation > System Recovery > Import System Data menu;
then system data will be listed. Select a data and press the OK button, then your data will be restored.
3.6
Clearing the services list
If you want to delete all services, select Installation > System
Recovery > Reset Service List; then you get asked for confirmation. If you select Yes, the services list will be cleared.
NOTE
After performing the service list reset, you have to search services again.
3
34
Preference Settings
Chapter 4
Preference Settings
4.1
Language settings
You can select the language in
which the menu would be displayed. In addition to that, you
can select the language of audio
track and of subtitle track.
Select the Settings > Language
menu. You should see a screen
like the left figure.
4.1.1
Menu language
Set the Menu Language option to your desired language. Once
you select a language, the menu will be immediately displayed
in the selected language.
4.1 Language settings
4.1.2
35
Subtitle language
Set the 1st Subtitle Language option and the 2nd Subtitle Language option to your desired languages. When you watch a
programme, if the programme has a subtitle track of the language that is designated for the 1st Subtitle Language, it will be
displayed. If the first language is not available but the second
language is available, the subtitle of the second language will
be displayed. If there is no available language, no subtitle will
be displayed.
Apart from this setting, you can select a subtitle track with the
button. See § 5.2.5 for a detailed description.
Some broadcaster may send a subtitle track dedicated to persons who have difficulty in hearing. Even when one or more
subtitle tracks are available, that subtitle track will be displayed
prior to those you have designated for the 1st Subtitle Language and the 2nd Subtitle Language options if the Hard of
hearing option is set to On.
4.1.3
Audio language
Set the 1st Audio Language option and the 2nd Audio Language option to your desired languages. When you watch a
programme, if the programme has an audio track of the language that is designated for the 1st Audio Language, it will
be outputted. If the first language is not available but the
second language is, the audio of the second language will be
outputted.
Apart from this setting, you can select an audio track with the
button. See § 5.2.4 for a detailed description.
4
36
Preference Settings
4.2
Video and audio settings
You have to configure the video
and audio settings appropriately
for your television set and other
appliances.
Select the Settings > A/V Output
menu. You should see a screen
like the left figure.
4.2.1
High definition television
The digital receiver supports various video resolutions from
576 to 1080. In general a resolution of 720 or more is considered
high definition. The higher the resolution, the better the quality.
However, if your television set does not support high definition,
you cannot enjoy high definition quality picture.
Set the Video Format option as you desire.
If you set this option to 576P, the digital receiver will present
even high definition programmes in resolution of 576. On the
contrary, if you set it to 1080I, the digital receiver will present
even standard definition programmes in resolution of 1080.
It is recommended setting it to Auto if you have a high definition television. With that setting the digital receiver will
present a programme as it is without any resolution conversion.
While watching television you can change the resolution with
the VF button. Whenever you press it, the video resolution
will be changed in turn.
If you have the digital receiver linked to your television by
the component video connectors (Y, Pb and Pr), set the HD
Output option to Component. Otherwise if you have connected
4.2 Video and audio settings
37
it to your television by the SCART connector, set this option to
Scart.
NOTE
You can enjoy only standard definition video with the following
connectors:
• Composite video connector (VIDEO)
• SCART connector (TV)
4.2.2
Colour model
Through the TV SCART connector, the digital receiver is able
to output video in various colour models.
If you have the digital receiver linked to your television by this
connector, you should set the SCART Output option to your
desired colour model.
If you have connected via the RCA connector labeled VIDEO
on the back panel, you do not have to set this option because
the digital receiver outputs CVBS video through the RCA connector independently of the SCART connector.
However, if you have connected via the S-VIDEO connector,
you have to set this option to S-Video because the output
through S-Video connector comes from the SCART interface.
4.2.3
Video cassette recorder
You can have the digital receiver linked to your video cassette
recorder or such an appliance by the VCR SCART connector. In
this case, the digital receiver will operate differently depending
on the setting of the VCR Scart Type option. If the option is
set to Standard, the digital receiver will pass the video from
the video cassette recorder to your television when it starts
playback. But if the option is set to External A/V, the digital
receiver will not pass the video automatically.
4
38
Preference Settings
NOTE
It is impossible for the digital receiver to record the video that
the video recorder plays back. Because the digital receiver is
just a bypass for the video recorder.
4.2.4
Television aspect ratio
If you have a wide-screen television, set the TV Aspect Ratio
option to 16:9.
You can enjoy both wide-screen programmes and normalscreen programmes with your wide-screen television as the
above figures show. To watch normal-screen programmes in
full screen like the left figure, set the Display Format option
to Full. Normal-screen pictures then will be inflated to fit to
the width of the wide screen. Otherwise, to watch them in the
original ratio like the right figure, set it to Center.
Otherwise, if you have a normal-screen television, set the TV
Aspect Ratio option to 4:3.
4.3 Local time setting
39
You cannot fully enjoy wide-screen programmes with your
normal-screen television as the above figures show. The left
figure shows a normal picture displayed in the normal screen.
To watch wide-screen programmes in the shape like the centre
figure, set the Display Format option to Letter Box. Wide-screen
pictures then will be reduced to fit to the width of the normal
screen. Otherwise, to watch them in the shape like the right
figure, set it to Center extract. Then wide-screen pictures will
be cut out on the left and right sides equally to fit to the width
of the normal screen.
4.2.5
Audio mode
Basically, there are two audio sources as you can find two audio
sockets on the back panel of the digital receiver. You can enjoy
only one source or both of them in either stereo or mono. Set
the Sound Mode option as you desire.
Apart from this setting, you can change the sound mode with
the
button. See § 5.2.4 for a detailed description.
The digital receiver can output two types of digital audio signals via the S/PDIF connector. One is an encoded signal, and
the other is a decoded signal. If your digital audio system does
not have a Dolby Digital decoder, you have to set the Dolby
Digital option to Off. Otherwise, set it to On.
NOTE
If the service you are currently watching does not provide
Dolby Digital, you cannot watch the programme with Dolby
Digital sound even though you set the Dolby Digital option to
On.
4.3
Local time setting
You should set your local time for timer events.
4
40
Preference Settings
If you do not set the local time correctly, the programme time
table provided by the programme guide may be distrustful.
For the programme guide, refer to § 5.3.
Select the Settings > Time menu.
You should see a screen like the
left figure.
You can set the clock manually
or use the time signal, Greenwich Mean Time (GMT), carried
as part of the digital television
broadcast.
To use Greenwich Mean Time,
take the following steps:
1. Set the Mode option to Auto; then the Time Offset option
becomes enabled.
2. Set the Time Offset option to the time difference between
your time zone and GMT referring to Table 4.1.
3. To get Greenwich mean time, set the GMT Collection
option to one among the following:
Normal from all transponders
CAS Only from transponders of pay services
User Select from transponders specified by user
If you set it to User Select, then the Satellite option and
the Transponder option become enabled. Select your desired satellite and transponders at those options. With
the above settings, the digital receiver will scan all specified transponders one by one until to get the Greenwich
Mean Time.
4. Make sure that your local time is correctly displayed on
the Local Time option.
4.3 Local time setting
41
Table 4.1: Time offset table
Time offset
City
GMT − 12:00
GMT − 11:00
GMT − 10:00
GMT − 09:00
GMT − 08:00
GMT − 07:00
GMT − 06:00
GMT − 05:00
GMT − 04:00
GMT − 03:30
GMT − 03:00
GMT − 02:00
GMT − 01:00
GMT
GMT + 1:00
GMT + 2:00
GMT + 3:00
GMT + 3:30
GMT + 4:00
GMT + 4:30
GMT + 5:00
GMT + 5:30
GMT + 6:00
GMT + 7:00
GMT + 8:00
GMT + 9:00
GMT + 9:30
GMT + 10:00
GMT + 11:00
GMT + 12:00
Eniwetok, Kwajalein
Midway Island, Samoa
Hawaii
Alaska
Pacific Time US, Canada
Mountain Time US, Canada
Central Time US, Canada, Mexico City
Eastern Time US, Canada, Bogota, Lima
Atlantic Time Canada, La Paz
Newfoundland
Brazil, Georgetown, Buenos Aries
Mid-Atlantic
Azores, Cape Verde Islands
London, Lisbon, Casablanca
Paris, Brussels, Copenhagen, Madrid
South Africa, Kaliningrad
Baghdad, Riyadh, Moscow, St. Petersburg
Tehran
Abu Dhabi, Muscat, Baku, Tbilisi
Kabul
Ekaterinburg, Islamabad, Karachi, Tashkent
Bombay, Calcutta, Madras, New Delhi
Almaty, Dhaka, Colombo
Bangkok, Hanoi, Jakarta
Beijing, Perth, Singapore, Hong Kong
Tokyo, Seoul, Osaka, Sapporo, Yakutsk
Adelaide, Darwin
Eastern Australia, Guam, Vladivostok
Magadan, Solomon Islands, New Caledonia
Fiji, Auckland, Wellington, Kamchatka
To set the local time manually, set the Mode option to Manual and enter your local time to the Local Time option with
the numeric buttons. The time format is day/month/year 24hour:minute.
To change the time format to 12-hour format, set the Time
Format option to 12 Hour.
If daylight saving time is observed in your area at the moment,
set the Daylight Saving Time option to On.
4
42
Preference Settings
NOTE
Daylight saving time adds one hour to the time when the option is set to On. When setting the time offset from Greenwich
Mean Time, make sure that time offset does not include daylight saving time.
4.4
Parental control
In general, television programmes are classified according to
the level of violence, nudity and language of their contents.
When you are watching a programme, you can check its programme classification on the information box. For the information box, see § 5.2.3.
You can prevent your children from watching specific programmes by specifying a programme classification.
Select the Settings > Parental
Control menu. You should see
a screen like the left figure, and
you will be asked your Personal
Identification Number (PIN).
The number is initially set to
‘0000’ as a default.
If you wish to block 15 or above rated programmes, set the
Censorship option to 15 (age). Setting it to No block blocks no
programme; on the other hand, setting it to Total block blocks
every programme.
4.5 Recording Settings
43
NOTE
If a programme does not have any programme classification
information, your censorship setting will not take effect.
If anyone is trying to watch a programme that is of or above
the censorship setting, the person has to enter the personal
identification number to override.
To change the number, select the Change PIN Code menu; then
an input box appears. You have to enter a desired number
twice for confirmation.
You can also restrict uses of some menus. Selecting the Access
Control menu displays a list of menus that you can lock. If
the Time item is set to Locked, you have to enter the personal
identification number when accessing the Time menu. If you
enter a wrong number, you cannot use the menu. To release
the item, set it to Unlocked.
4.5
Recording Settings
To configure the recording related settings, select the Settings
> Recording menu.
You should see a screen like the
left figure.
You can record a programme into both an external or the builtin hard disk drive. If you want to record a programme into an
external hard disk drive, set Recording Drive option to External;
otherwise, set this option to Internal.
4
44
Preference Settings
You can adjust the duration of the time shift. Set the Time
Shifting option as you desire. Its available range is 30 minutes
to 5 hours. If you do not want to use the time shift, set this
option to Disable.
If you set the Time Shift Storage option to Enable, the saving
parts which for the time shift will be recorded in the TimeShift
folder of the hard disk drive.
You can set the duration of the timer recording. Set the Timer
Recording Duration option as you desire. Its available range
is 10 minutes to 3 hours. In addition, you can adjust the time
padding of timer recording. Set the Time Padding of Timer
Recording option as you desire. Its available range is 0 to 30
minutes.
You can adjust the duration of the instant recording. Set the
Instant Recording Duration option as you desire. Its available
range is 30 minutes to 5 hours.
4.6
Playback Settings
To configure the playback related settings, select the Settings
> Playback menu.
You should see a screen like the
left figure.
If you want to play back a recorded file from beginning, set
Starting Position option to Beginning. To play back a recorded
file from the part where you were watching, set this option to
Continuing.
4.7 Adjusting the On-Screen Display
45
To record again a scrambled recording file with descrambling
during playback, set the Descramble Mode option to Auto
Recording; otherwise, set this option to Normal.
You can adjust the jump time interval which is used in playback.
Set the Jump Time Interval option as you desire. Its available
range is 10 seconds to 3 minutes.
If you want to use extensional trick mode, set the Trick Mode
Level option to 2x, 4x, 8x, 16x, 32x, 64x; otherwise, set this
option to 4x, 16x, 64x.
4.7
Adjusting the On-Screen Display
To adjust the On-Screen Display
(OSD) related settings, select the
Settings > OSD menu.
You should see a screen like the
left figure.
To adjust the transparency level of the OSD, set the OSD Transparency option as you desire. Its available range is 0 to 50
percent.
To adjust the display time of the information box, set the Info
Box Display Time option as you desire. Its available range is 1 to
30 seconds. If you set this option to No Infobox, the information
box will not be displayed when you switch services. However,
pressing the
button will display the information box. If
you set this option to Never Hide, the information box will
always be displayed. For the information box, see § 5.2.3.
In addition, you can raise or lower the position of the information box. To do that, set the Info Box Position option as you
4
46
Preference Settings
desire. Its available range is −10 to +3 lines. The higher you
set the option, the lower the information box will be positioned.
To use an animation effect when changing menu, set the Animation option to Enable.
To use the service name scrolling at the service list screen, set
the Text Scroll option to Full Scroll or Part Scroll. If you set this
option to Full Scroll, a service name will be fully scrolled. If
you set this option to Part Scroll, a service name will be scrolled
only from beginning of the name to end of the name.
4.8
Front Display Settings
To adjust the front display related settings, select the Settings
> Front Display menu.
You should see a screen like the
left figure.
If you want to use the front display scrolling continuously, set
the Main Display Scrolling option to Unlimited. Setting it to
Once do the scrolling one time. Set it to Disable not to use the
scrolling.
To display the current time on the sub display of the front
display, set the Sub Display Content option to Time. Otherwise,
set this option to Default to display the name of the upper
menu.
To adjust the brightness of the front display in operation mode,
set the Brightness in Operation Mode option as you desire.
4.9 To use MediaHighway programme guide
47
You can also adjust the brightness of the front display in
standby mode. To do that, set the Brightness in Standby Mode
option as you desire.
4.9
To use MediaHighway programme guide
Almost every service provider would provide the electronic
programme guide. However, you can get more abundant
programme information from the specific transponder that
provides only programme guides. For detailed description
about the electronic programme guide, see § 5.3. MediaHighway stands for the transponder dedicated to the electronic
programme guide.
If you want to use this feature, select the Settings > MediaHighway EPG menu.
Set the MediaHighway EPG option to On to activate this feature;
then the other options become enabled. Set the Satellite Name
and Home Transponder options to available ones, and set the
Tuner Select option to a tuner which receives them.
4.10
Adjusting a size of picture in picture
You can adjust a size of picture-in-picture screen. To do that,
select the Settings > Others menu; then, set the Default PIP
Size option as you desire. For the picture-in-picture, see § 5.6.
4.11
Slideshow Settings
You can change a time interval and effect of slideshow in the
photo album. For the photo album, see § 8.3.
To change the time interval of slideshow, select the Settings >
Others menu; then, set the Slideshow Time Interval option as
you desire. Its available range is 3 to 10 seconds.
To change the effect of slideshow, select the Settings > Others
menu; then, set the Slideshow Effect option as you desire. There
are four types of effects as follows:
4
48
Preference Settings
Overlap overlaps the current picture and a following picture.
Cover covers the current picture with a following picture.
Move moves the current picture and displays a following
picture.
Mosaic displays a following picture with a mosaic effect.
To use those effects ramdomly, set this option to Random. The
default value is Random.
4.12
Standby mode Setting
You can display the current time on the front display in standby
mode. To display the time, select the Settings > Others menu
and set the Standby Mode option to Active; otherwise, set it to
Passive. When you set the Standby Mode option to Active, the
receiver can also bypass the signal from the antenna.
49
Chapter 5
Daily Usage
5.1
Volume control
Use the VOLUME+ and VOLUME− buttons to alter the volume
to a comfortable level. You may need to adjust the volume on
your television set too. To temporarily switch off the sound,
press the
button. Press it again to restore the sound to
previous level.
5.2
Watching television
To change services, press the CHANNEL+ or CHANNEL− button.
Pressing the
button switches to the previously viewed
service. In addition, you can switch to your desired service by
entering its service number with the numeric buttons. You can
also select a service to watch in the services list.
5.2.1
The services list
To display the services list, press the OK button.
5
50
Daily Usage
On the services list, you can see
the service information:
• Service number and name
• Transmitting satellite
• Receiving tuner: T1 stands for
the first tuner; T2 stands for
the second tuner.
• Transponder information
A dollar sign ($) marked on some entries indicates pay service.
To watch pay services, you need a subscription card.
To select a desired service, put the highlight bar on its entry
with the
or
be displayed.
button and press the OK button; then it will
Pressing the
or
button skips over 10 entries up or down.
Entering a service number with the numeric buttons puts the
highlight bar on its entry.
You can switch between the television services list and the
radio services list by pressing the
button.
Pressing the F3 button performs an alphabetic browse. For
instance, when the highlight bar is on an entry of which initial
is B, pressing the F3 button puts the highlight bar on the first
entry of which initial is C.
To display favourite lists, press the F2 button.
Pressing the Option button displays the additional options, with
which you can do the following:
• Select your desired satellite at the Satellite option, then
only provided services by the selected satellite will be
listed.
5.2 Watching television
51
• Select your desired tuner at the Tuner option, then only
provided services through the selected tuner will be
listed.
• By setting the Show Provider option to On, you can view
service entries by groups of broadcasters.
• To change the name of the highlighted service, select the
Rename option; then the on-screen keyboard appears,
with which you can enter a new name. See § 6.3 for how
to use the on-screen keyboard.
• You can prevent other family members from watching the
highlighted service by setting the Lock option to Locked.
You have to enter your personal identification number to
watch or unlock it.
• To delete the highlighted service, select the Delete option;
then you get asked for confirmation. If you select Yes, it
will be deleted. If you want to restore it as before, you
have to perform service search again. See § 3.1 for service
search.
• To add the highlighted service into a favourite group,
select the Add to Fav option; then the favourite groups
will be displayed. Put the highlight bar on a desired
group and press the OK button.
• You can additionally sort the services list with the Sorting
option as follows:
Default by service number
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
CAS–FTA from pay services to free services
Provider by broadcaster
Fav–NoFav from favourite services to unfavourite services.
5
52
Daily Usage
Transponder by transponder.
5.2.2
The favourite services list
You can select a service on a favourite list as well as on the
services list.
To display the favourite lists,
press the F2 button at the services list screen. For the services
list, see § 5.2.1.
To select a favourite list, put
the highlight bar on a desired
favourite group list and press
the OK button; then favourite
services belonging to the highlighted group are listed.
For how to edit the favourite lists, refer to § 6.2.
To select a favourite service, put the hightlight bar on a desired
service and press the OK button. Once you select a desired
service with the OK button, it will be displayed. To select other
group, press the
button.
After you have selected a favourite service, if you then switch
to another service using the
or
button, it will be also
another favourite service of the selected group. The digital
receiver will remind you what group you have selected by
displaying its name at the top right of the screen whenever you
switch services.
To return to the services list, press the F1 button.
Besides that, you can add or delete a favourite group or service.
To add the service you are currently watching into a favourite
group, press the Option on the favourite group list. Then, select
Add this service item and press the OK button.
5.2 Watching television
53
To delete a service, press the Option on the favourite group list.
Then, select Delete item and press the OK button; then you get
asked for confirmation. If you select Yes, it will be deleted.
5.2.3
Viewing programme information
Pressing the
button displays the information box, on
which you can see all of the following:
•
•
•
•
•
•
•
•
•
•
Service number and name
Transmitting satellite
Receiving tuner
Transponder information
Signal level and quality
Programme name
Programme classification symbol
Programme summary
Broadcasting time
Current time
In addition, you might see the following symbols:
• Subtitle symbol ( ) if subtitle tracks are provided on the
current programme.
• Teletext symbol (
current service.
) if teletext pages are provided on the
• Dolby symbol (
) if a Dolby audio track is provided
on the current programme.
• Lock symbol (
) if the current service is locked.
• Dollar symbol ($) if the current service is a pay service.
• Multifeed symbol ( ) if the current programme is provided as a multifeed programme. To use this feature,
refer to § 5.4.
If the electronic programme guide is provided on the current
service, you can see the information about the current and next
5
54
Daily Usage
programmes with the
or
button. You can also see the
information about other services with the
or
. In this
case, you can change a service by pressing the OK button.
Pressing the
button once more displays detailed information about the current programme. To hide the information
box, press the EXIT button.
5.2.4
Selecting audio tracks
Some programmes are provided with audio tracks in one or
more languages. Pressing the
button displays available
audio tracks. Once you select an audio track, that track will be
heard. In addition, you can enjoy audio tracks in four sound
modes: Stereo, Mono, Left or Right. However, if a multifeed
programme is provided at the moment, video tracks will be
displayed. In this case, you have to press the
button once
more to select an audio track.
5.2.5
Selecting subtitle tracks
Some programmes are provided with subtitle tracks in one or
more languages. If the current programme provides subtitle
tracks, the subtitle symbol ( ) will be marked on the information box. Pressing the
button displays available subtitle
tracks. Once you select a subtitle track, it will be displayed.
5.2.6
Viewing teletext
On some services, such information as weather reports, news
or stock quotations is provided by means of teletext. If the
current service provides teletext, the teletext symbol ( ) will
be displayed on the information box. Press the
button to
view teletext pages.
Select a page to view by entering its page number with the
numeric buttons. You can zoom into a teletext page with the
F3 button, and adjust its transparencylevel with the F4 button.
To clear the teletext screen, press the EXIT button.
5.3 Viewing electronic programme guide
5.3
55
Viewing electronic programme guide
The Electronic Programme Guide (EPG) shows the current and
scheduled programmes that are or will be available on each
service with a short summary for each programme.
Selecting the Recording > Program Guide or pressing the
GUIDE button displays the electronic programme guide, on
which you can see the following:
•
•
•
•
Scheduled programmes
programme summary
Broadcasting date
Broadcasting time
To see detailed information of a desired programme, put the
highlight bar on the programme with the navigation buttons
and press the
button.
You can travel over previous days with the F2 button, and can
travel over next days with the F3 button.
To see the programme guide for radio broadcasts, press the
button. To switch it back, press the
button again.
Pressing the F1 button displays the programme guide in the
different form. To switch it back, press the F1 button again.
You can make a timer recording on the electronic programme
guide. See § 7.1.3 for detailed description.
5.4
Watching multifeed programme
Some broadcasts such as sports channels can provide a variety
of perspectives on a programme at the same time. We call it a
multifeed programme. You can select and watch a perspective
you prefer.
5
56
Daily Usage
If a multifeed programme is provided on the current service,
the multifeed symbol ( ) will be marked on the information
box. Press the
button, then available video tracks will be
listed. Once you select one, it will be displayed. At this time,
you have to press the
button once more to select audio
tracks.
5.5
Using time shift
You can pause and resume a live television programme, and
even rewind and replay it. When you are watching a programme and you miss something, you can rewind and replay
it. Or when your attention is needed elsewhere, you can pause
live TV and resume a short time later without losing any of the
programme.
When you do this, you are no
longer watching the live programme, instead you are watching a delayed presentation. This
is called time shifted television.
You can skip commercials until
you catch up to the live broadcast.
In order to use the time shift feature, set the Time Shifting
option to desired duration of time. Then the digital receiver
will keep as much time as you set in the option. See § 4.5.
The time shift will reset each time you change to another service.
With the time shift, the following operations are possible:
• To go back in time, hold down the
button; to go
forward, hold down the
button. The progress bar is
displayed momentarily with a preview window.
5.6 Using picture in picture
57
• You can navigate using the progress bar, refer to § 7.3.1.
• You can jump backward and forward by pressing the F4 and F3 buttons. You can change the jump time at the
Jump Time Interval option. See § 4.6.
• You can change playback speed. See § 7.3.2 for slow
motion. For fast motion, see § 7.3.3.
• To check your current position in time shift, press the
button. The time difference compared to live programme is displayed momentarily in top right corner of
screen. A value of −02:00 means two minutes behind
live programme.
• To make a recording of what is in time shift, see § 7.1.4.
• To end time shift, press the
gramme will be displayed.
button. The live pro-
NOTE
You can adjust some options of the time shift. Refer to § 4.5.
5.6
Using picture in picture
You can watch two services
at the same time with one of
them displayed in a sub-picture.
We call this feature picture-inpicture.
The instructions on how to use
the picture-in-picture feature are
as follows:
5
58
Daily Usage
1. Press the F1 button to display a sub-picture, on which
another service will be displayed. Pressing the F1 button
once more hides the sub-picture.
2. To display the services list for the sub-picture, press the
Option button.
NOTE
When a recording is in progress, the available services in
the services list may be limited.
3. Pressing the
button moves the sub-picture counterclockwise, and pressing the
button moves it clockwise.
4. Pressing the SAT button swaps the main picture with the
sub-picture. Even when you play back a recording, you
can watch a live programme in the sub-picture. However,
you cannot swap the pictures in that case.
5. If both pictures are pay services, only the main-picture
will be displayed. To display two pay services, set the
Descramble multiple services option to Enable referring
to § 1.3.
59
Chapter 6
Editing Services
6.1
Editing the services list
You would have got the services list after service search. You
can rename, move, lock or delete service entries on the services
list.
Select the Installation > Edit Services > Edit Service List menu.
You should see a screen like the
left figure.
There are editing options on the
left column and service entries
on the right column.
Once you put the highlight bar on a desired option on the
left column and press the OK button, you can select a desired
service to edit on the right column. To go over to the other
column, press the F1 button.
6
60
Editing Services
To edit the radio services list, press the
button; then radio
service entries will be listed on the right column. To switch
back to the television services list, press it again.
To change the name of a service, select the Rename and select a
desired service; then the on-screen keyboard appears. See § 6.3
for how to use the on-screen keyboard.
Unlike analogue broadcasts, each service does not have a
proper service number in digital broadcasts. Service numbers are just assigned to services in the order that they were
found in service search. So you can reassign a service number by moving a service entry. To move a service entry, select
the Move option and select a desired service; then the selected
service becomes darker. As you move it up or down, it gets
renumbered according to the position. Press the OK button to
fix it.
You can lock some services to prevent your children from
watching them. To lock a service, select the Lock option and
select a desired service; then the selected service gets marked
with a lock symbol (
) on it. If anyone tries to watch a locked
service, the person has to enter the personal identification number that is set to the Change PIN Code option. See § 4.4 for this
option. Pressing the OK button on a locked service entry turns
it back to be unlocked.
To delete a service, select the Delete option and select a desired
service with the OK button, and then press the EXIT button;
you get asked for confirmation. If you select Yes, the selected
service will be deleted. If you want to undo the deleted service,
there is nothing you can do but perform a service search again.
Once you select the Sort option on the left column, sorting
options are displayed as follows:
Default by service number
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
6.2 Editing the favourite list
61
CAS–FTA from pay services to free services
Provider by broadcaster
Fav–NoFav from favourite services to unfavourite services.
Transponder by transponder
6.2
Editing the favourite list
You can make your own favourite services list. In fact, you can
define multiple favourite services lists, each being a ‘group’ of
chosen services.
Select the Installation > Edit Services > Edit Favorite List menu.
You should see a screen like the
left figure.
There are three columns:
• Group list (left)
• Favourites list (centre)
• Services list (right)
The services list contains all available services, whereas the
favourite list contains only chosen services that have been
added to the highlighted group. As you move the highlight
bar up or down on the group list, favourite services belonging
to the highlighted group get shown in the favourites list.
You can add up to 30 groups. To add a group, select the NEW
option in the group list; then the on-screen keyboard appears.
See § 6.3 for how to use the on-screen keyboard.
To rename a group, put the highlight bar on the group entry
you want and press the F2 button; then the on-screen keyboard
appears. See § 6.3 for how to use the on-screen keyboard.
6
62
Editing Services
To delete a group, put the highlight bar on the group entry
you want and press the F3 button; then a message box appears
asking you for confirmation. If you select Yes, it will be deleted.
You can add a favourite service to a group by taking the following steps:
1. Put the highlight bar on a desired group entry in the
group list and press the OK button to select it. The highlight bar then moves to the services list.
2. To add a service to the selected group, put the highlight
bar on a desired service entry and press the OK button.
The selected service entry gets added to the favourite list.
Repeat this step to add more entries.
3. Press the F1 button and the highlight bar gets moved to
the favourite list. You can delete a favourite entry with
the OK button.
4. To select another group, press the F1 button again. By
pressing the F1 button, the highlight bar gets moved to
each column.
At the same time, you can rearrange a group’s favourites by
moving a favourite entry. To move a favourite entry, put the
highlight bar on the favourite entry you want and press the F2 button. Move it to a desired place and press the OK button.
To add radio services, press the
button at the services list
column; then radio service entries get listed in the services list.
To recall the television services list after adding radio services,
press the
button again.
With your favourite services list, you can select your favourite
services more easily. Refer to § 5.2.2 for detailed description.
6.3 How to use the on-screen keyboard
6.3
63
How to use the on-screen keyboard
You can move the highlight key
horizontally with the
and
buttons and vertically with the
and
buttons. Pressing the
OK button on a key enters its letter in the input line. To type a
space, select the Space key. To
type lower case letters or numerals, select the Shift key.
To delete a letter, put the cursor to the right of the desired letter
on the input line and then select the Del key. You must select
the Save key to store the name; otherwise if you press the EXIT button, the name will not be stored.
6
64
Recording and Playing
Chapter 7
Recording and Playing
You can record a service to an external hard disk drive as well
as the built-in hard disk drive.
NOTE
To use an external hard disk drive, you must connect the external hard disk drive to the USB port of the digital receiver. The
hard disk drive should have its own power supply. Because the
digital receiver cannot provide enough power for the external
hard disk drive.
CAUTION
Do not disconnect the external hard disk drive while recording
or playing back. It may cause damage to recorded programmes.
You should disconnect the external hard disk drive in standby
mode only.
You can record a service while watching another with the SRP 2100 digital receiver.
You can record two different services while watching another if
two of the services are provided through the same transponder.
7.1 Recording a programme
65
The SRP - 2100 digital receiver has two tuners so that you can
enjoy the following:
• While playing a recording back, you can watch a service
in the sub-picture using the picture-in-picture feature.
• You can record two different services while playing back
a previously recorded programme.
• You can even record two different services while watching two other different services—only if two or more
services are provided in a same transponder and the
other services are provided in another same transponder.
In this case, you can watch two services at the same time
using the picture-in-picture feature. See § 5.6 for the
picture-in-picture feature.
7.1
Recording a programme
Once recording has started, a symbol like the left
figure will be displayed at the top right of the screen
for a few seconds.
When you are watching a different service from the service
being recorded, you will see a number on the centre of the
symbol, this indicates the order that the recording has started.
To record two programmes simultaneously, two tuners are
allocated for the recording. Therefore, you can only change to
a limited number of services while the two programmes are
being recorded.
CAUTION
Do not move the digital receiver nor pull out the power plug
while it is running. It may cause damage to recorded programmes. Topfield is not responsible for damages inflicted
on files that are stored on the hard disk drive.
7
66
Recording and Playing
7.1.1
Instant recording
To instantly record a programme you are watching at present,
press the
button.
Pressing the
button will not pause the current recording
like it does with a video cassette recorder. Instead, pressing
the
button will pause the live show and begin time shifting
within the current recording even with the Time Shifting option
disabled. However, it is still possible to pause a recording.
After a recording is started,
pressing the
button displays
a menu like the left figure, in
which you can set the recording
duration.
To specify an arbitrary recording duration, set the Duration
option as you desire with the
and
buttons and press the
OK button; the recording will end at the specified time.
If the information about the next programme is provided by
the electronic programme guide, the ’After this program’ and
’After next program’ options will be enabled. Once the ’After
this program’ option is selected, the current recording will stop
when the current programme is scheduled to end. Likewise,
once the ’After next program’ option is selected, the current
recording will stop when the next programme is scheduled to
end.
7.1 Recording a programme
67
To stop recording, press the
button; then a box like
the left figure appears, which
shows programmes currently being recorded. If you select one,
its recording will stop.
While a recording is going on, you can watch or record another
service. To additionally record another service, switch to the
service you want to record, and press the
button.
Once a recording is started, it is put on the recorded programme
list even though it is not finished yet. The recording file is
named after its service name with a suffix of a number.
To view the recorded programme list, press the
button or
alternatively select the Recording > Recorded Program menu.
See § 7.2 for detailed description about the recorded programme list.
7.1.2
Recording Reservation
You can set a service to be recorded at a specific time. Even
if the digital receiver is in standby mode, it will switch into
operation mode and start recording at a specified time. When
the recording comes to the end, the digital receiver will switch
back into standby mode again in one minute.
However, if you press any button on the remote control or on
the front panel even just one time, the digital receiver will not
switch into standby mode.
7
68
Recording and Playing
To add a timer recording, select the Recording > Reservation
menu; then the timer list will be
displayed.
To add a new timer event, press
the F1 button, and a box like the
left figure appears. Take the following steps:
1. Set the Record option to On to make a recording. If this
option is set to Off, the digital receiver will turn on at the
specified time but not record; instead, you may record
with your video cassette recorder or suchlike in this case.
2. If you want a radio programme, set the Type option to
Radio; otherwise, set this option to TV.
3. Set the Satellite option to the satellite which transmits the
service you want. Pressing the OK button on this option
displays a satellite list, from which you can select your
desired satellite. Set the Tuner Select option to a tuner to
receive your desired service.
4. Set the Service option to the service which provides the
programme you want. Pressing the OK button on this
option displays a services list, from which you can select
your desired service.
5. Set the Mode option as you desire. There are five timer
modes:
One Time means literally ‘one time’.
Every Day means literally ‘every day’.
Every Weekend means ‘Saturday and Sunday every
week’.
7.1 Recording a programme
69
Weekly means ‘one day every week’.
Every Weekday means ‘from Monday to Friday every
week’.
If your favourite programme is broadcast at weekends
and you wish to record every episode of the programme,
set the Mode option to Every Weekend.
6. Set the Date option to a desired date, on which the digital
receiver will turn on. The date format is day/month/yearday of the week.
Set the Start Time option to a desired time, at which the
recording will be started. The time format is hour:minute.
7. Set the Duration option to a desired time, in which the
recording will be finished.
8. Pressing the OK button on the File Name option displays
the on-screen keyboard, with which you can specify a
file name for the timer recording. If you do not specify
anything, it will be named after the service name. See
§ 6.3 for how to use the on-screen keyboard.
9. To set a recording reservation with the above settings,
select the OK item; otherwise, it will not be saved and
will not occur.
You can also edit or delete timer events in the timer list.
To edit a timer entry, put the highlight bar on the entry you
want and press OK button; then appears a box in which you
can change its settings in the same manner as making a new
one.
To delete a timer event, put the highlight bar on the entry you
want to remove and press the F2 button; then you get asked
for confirmation. If you select Yes, it will be deleted.
To delete all timer event, press the F3 button.
You can sort timer events by time with the F4 button.
7
70
Recording and Playing
7.1.3
Scheduling recordings using the programme guide
If the electronic programme
guide is properly provided, you
can make timer events on it. The
instructions on how to make
timer recordings using the electronic programme guide are as
follows:
1. Press the GUIDE button to display the electronic programme guide.
2. Select a programme you want to record with the navigation buttons.
3. To make a timer event without recording, press the OK button; the letter P is displayed. To make a timer event
with recording, press it once more or alternatively press
the
button; then the letter R is displayed.
4. Pressing the OK button once more will cancel the timer.
7.1.4
Recording a time-shifted programme
While watching a programme with time shift, you can record it
by performing the following steps:
1. Press the
button to display the progress bar.
2. To move to the beginning of the desired scene, hold down
the
or
button until it is reached.
3. Press the
button to start recording. The time shift
buffer from that position onwards will now be recorded.
7.1 Recording a programme
4. Press the
button to stop recording.
5. Press the
button once more to stop time shift.
71
See § 5.5 for detailed description about the time shift feature.
NOTE
You cannot watch a time-shift recorded file in fast motion and
slow motion during playback.
7.1.5
Recording a pay service programme
You can record a pay service programme without the subscription card. However, you need the subscription card to play
it back because it has not been descrambled. So it is recommended recording pay service programmes with the subscription card so that they can be recorded in descrambled form. In
that case, you can enjoy them without the subscription card
like free services.
To record a programme of a pay service in descrambled form,
perform the following steps:
1. Select a programme of a pay service you want to record.
2. Make sure that the subscription card is inserted in the
slot on the front of the digital receiver.
3. Start recording.
4. Do not switch to other service nor use time shift until it
is finished.
NOTE
You cannot watch a pay service recorded file in fast motion and
slow motion during playback.
7
72
Recording and Playing
NOTE
If you switch to other service or use time shift in the middle
of recording a pay programme, it will be recorded without
descrambling from that moment. Even if the recording is only
partially descrambled, you need the subscription card to play
it back.
7.2
File archive
When a programme is recorded, it is stored as a file on the hard
disk drive of the digital receiver. You can select a recording to
play back from the recorded programme list.
Select the Recording > Recorded
Program menu or alternatively
press the
button to display
the recorded programme list.
The file information is comprised of the following elements:
file number, file name, recording
time, playing duration, file size
and so on.
You can play, move, delete, rename and lock a recording file.
You can also sort the recording files by file name, playing duration or file size. In addition, you can make a new folder.
7.2.1
To delete a recording
To delete a recording, put the highlight bar on it and press the
F4 button; then you get asked for confirmation. If you select
Yes, it will be deleted.
7.2 File archive
7.2.2
73
To sort recordings
To sort the recordings, perform the following steps:
1. Press the Option button to display the additional options.
2. Set the Sorting option to Alphabetic, Time or Size as you
want.
3. Press the EXIT button.
4. They will be sorted by the specified option.
7.2.3
To lock a recording
To lock a recording so that other people cannot play or delete
it, perform the following steps:
1. Put the highlight bar on a desired recording.
2. Press the Option button to display the additional options.
3. Set the Lock option to Locked.
4. Press the EXIT button.
5. The lock symbol (
) is displayed on it.
If you select a locked recording to play it back, you will be
asked for your personal identification number.
7.2.4
To rename a recording
To change the name of a recording, perform the following steps:
1. Put the highlight bar on a desired recording.
2. Press the Option button to display the additional options.
3. Select the Rename option, and the on-screen keyboard
appears. Change the name and save it. See § 6.3 for how
to use the on-screen keyboard.
7
74
Recording and Playing
7.2.5
To make a new folder
To make a new folder, press the F2 button; then a new folder
named GROUP # is created. You can change its name in the
same manner as renaming a recording. See above.
7.2.6
To move a recording to another folder
To move a recording to another folder, put the highlight bar on
a desired recording and press the F3 button. If an external hard
disk drive is connected to the digital receiver, you get asked to
select between the built-in and external hard disk drive. Select
Internal; then the folders are listed. Once you choose a folder,
the recording is moved to it.
7.3
Playing back a recording
When a programme is recorded, its additional contents such as
audio tracks or teletext are also recorded together. So you can
enjoy them while playing back a recording.
The instructions on how to play a recording are as follows:
1. Select the Recording > Recorded Program menu or alternatively press the
button to display the list of
recorded programmes.
2. Put the highlight bar on a desired recording and press
the OK button.
3. Select Play option and press the OK button to start playback. In addition, you can set play mode options as
follow:
• If you want to playback the file from beginning, set
the Starting Position option to Beginning. To play
back the file from the part where you were watching,
set this option to Continuing.
7.3 Playing back a recording
75
• To descramble the file, set the Descramble Mode to
Auto Recording.
4. To stop playback, press the
button.
During a playback, you can enjoy the following tricks:
• To see the detailed information about the currently played
recording, press the
button; then the information
box appears and shows its file name, playing duration,
programme information, and so on.
• To pause playback, press the
press the
button.
button. To resume it,
• To go forward, hold down the
hold down the
button.
button; to go backward,
• To display the progress bar, press the
it, press the
button again.
button; to hide
• When the progress bar is hidden, you can move to a desired scene by entering the percentage with the numeric
buttons.
7.3.1
To navigate using the progress bar
First press the
button to display the progress bar, then:
• To go forward, hold down the
hold down the
button.
button; to go backward,
• To bookmark a position, refer to § 7.3.4.
• If there are no bookmarks, you can jump forward about
15 seconds at a time by pressing the F3 button.
• To jump to start of a recording, press the
button.
• To jump to end of a recording, press the
button.
• To hide the progress bar, press the
button again.
7
76
Recording and Playing
7.3.2
To play in slow motion
To watch in slow motion during a playback, press the
button. If you press it repeatedly, the playback speed changes in 4
steps: 1/2, 1/4, 1/8 and 1/16 times. To resume normal speed,
press the
button.
7.3.3
To play in fast motion
To watch in fast motion during a playback, press the
button.
If you press it repeatedly, the playback speed changes. To
resume normal speed, press the
button.
You can play not only forward but also backward in fast motion. To play backward, press the
button. If you press it
repeatedly, the playback speed changes. To resume normal
speed, press the
button.
You can change the playback speed in 3 steps (4, 16 and 64
times) or in 6 steps (2, 4, 8, 16, 32 and 64 times). See § 4.6.
7.3.4
To make a bookmark
You can mark favourite parts
of a recording by creating bookmarks, and then jump to them.
Bookmarks are stored with the
recording so that you can use
them again afterwards. To make
bookmarks, perform the following steps during playback:
1. Press the
button to display the progress bar.
2. To add a bookmark, press the F2 button at a desired
scene; then you will see a small dot appear above the
progress bar like in the picture above.
7.3 Playing back a recording
77
3. To jump forward to next bookmark, press the F3 button.
4. To jump to first bookmark, press the
F3 button.
button then the
5. To delete a bookmark, jump to it and then press the F2 button.
7.3.5
To play back a recording repeatedly
You can play back a recording repeatedly both in whole and in
part.
To play back in whole, press the
button when the progress
bar is hidden; then the repetition symbol (
) is displayed on
the information box. To cancel it, press the
button again.
To play back in part, perform the following steps:
1. Press the
button to display the progress bar.
2. Move to the beginning scene of the part you want to play
repeatedly by holding down the
or
button.
3. Press the
button, then the pointer starts to blink.
4. Move to the end scene; the part is marked in black.
5. Press the
button again to start repeated playback.
6. To cancel it, press the
is displayed.
7.3.6
button when the progress bar
To play back recordings in sequence
You can play several recordings continuously in sequence by
performing the following steps:
1. Press the
button or alternatively select the Recording
> Recorded Program menu to display the list of recorded
programmes.
7
78
Recording and Playing
2. Select each desired recording with the F1 button. Once a
recording is selected, it gets numbered.
3. Press the
button to start playback.
4. The selected recordings are played in the sequence that
they are numbered.
5. To jump to start of next selected recording, press the
button to display the progress bar, then press the
button.
7.3.7
To play back a scrambled recording
If you have recorded a programme of a pay service with the
subscription card, you can play it as freely like one of a free
service. Otherwise you need the subscription card to play it
back, because it has been recorded without unscrambling even
though it may have been partially descrambled.
On the recorded programme list, a purely green $ indicates the
recording has been wholly descrambled; on the other hand, a
yellowish green $ indicates it has been partially descrambled,
and a purely yellow $ indicates it has not been descrambled at
all.
Refer to § 7.1.5 for how to record a pay service programme.
7.4
Editing a recording
You can cut out or save a part such as commercial from a
recording by performing the following steps:
1. Press the
playback.
button to display the progress bar during a
2. Move to the beginning scene of the part you want to edit
by holding down the
or
button.
3. Press the
button, then the pointer starts to blink.
7.5 Copying a recording
79
4. Move to the end scene; the part is marked in black.
5. Press the F4 button, then the edit options are displayed.
6. If you choose the Cut option, it will be removed from the
original recording and discarded.
7. If you choose the Save option, the cut will be saved in a
new file which is named after the original recording with
a suffix of ‘CUT’ and a number.
NOTE
You can use only 2 times speed in fast motion during playback
of a edited file. And you cannot watch a edited file in slow
motion.
7.5
Copying a recording
When you record a pay service without the subscription card,
the recorded file will not be descrambled.
You can descramble and record the file in whole or in part
during a playback by performing the following steps:
1. Start playback of a recording you want.
2. Make sure that the subscription card is inserted in the
slot on the front of the digital receiver.
3. Move to a scene from which you want to start copy by
holding down the
or
button.
button, then it will be copied in a new file
4. Press the
which is named after the original recording with a suffix
of ‘COPY’ and a number.
5. To stop copying, press the
button.
7
80
7.6
Recording and Playing
Formatting the hard disk
You can delete all contents stored in a hard disk drive by formatting it. If you wish to do that, select the Installation > System
Recovery > Format Hard Disk menu; then select the hard disk
driver which you want to format. To format the built-in hard
disk drive, select the option to Internal; otherwise, select the
option to External to format an external hard disk drive which
is connected to the digital receiver. After selecting it, press the
OK button, then you get asked for confirmation. If you select
Yes, formatting will start.
CAUTION
Formatting the hard disk will delete all files permanently.
NOTE
If a new hard disk drive is installed, it must be formatted
because the file system of the digital receiver is different from
any of the personal computer. You can neither record nor use
time shift with an unformatted hard disk.
81
Chapter 8
Special Features
The SRP - 2100 has special features as MP3 playback, YouTube
playback, network game and so forth.
NOTE
To fully enjoy those functions, you have to configure the network settings correctly; otherwise, the function does not work
or partially works. For how to configure the network settings,
refer to § 9.2.
8
8.1
Playing back MP3 files
You can enjoy music or audio books in MP3 format on the
digital receiver.
Refer to § 8.4 for how to copy a file from an external hard disk
drive into the built-in hard disk drive of the digital receiver.
To play an MP3 file, perform the following steps:
1. Select the Entertainment > MP3 Player or press the
button and then the
or
button to display the MP3
file list.
82
Special Features
2. Put the highlight bar on a desired file; if you want to play
several files, select them with the F1 button.
3. Press the
button to start playback.
4. To stop playback, press the
button.
To play all MP3 files in a subfolder, put the highlight bar on a
desired folder, and press the
button.
8.2
Playing back video files
You can enjoy video files in DivX, vob, mkv, or mp4 format on
the digital receiver.
NOTE
The SRP - 2100 supports only DivX 3.x, 4.x and 5.x.
Refer to § 8.4 for how to copy a file from an external hard disk
drive into the built-in hard disk drive of the digital receiver.
To play a video file, perform the following steps:
1. Select the Entertainment > Media Player or press the
button, and then the
or
button to display the video
file list.
2. Put the highlight bar on a desired file; if you want to play
several files, select them with the F1 button.
3. Press the
button to start playback.
4. To stop playback, press the
8.3
button.
Viewing graphic files
You can view graphic files in jpg format with the digital receiver.
To view a jpg file, perform the following steps:
8.4 Copying files
83
1. Select the Entertainment > Photo Album or press the
button, and then the
or
button to display the list
of graphic files.
2. Put the highlight bar on a desired file and press the OK button; if you want to view several files using a slide
show, press the F1 button. You can change a time interval
and effect of slideshow. See § 4.11.
3. To stop viewing, press the EXIT button.
8.4
Copying files
You can copy files between the built-in hard disk drive and
external hard disk drive.
NOTE
If your external hard disk drive is formatted in the FAT16/32 or
NTFS, it can only be read. To enable to write and read, the hard
disk drive must be formatted in the JFS or Ext2/3 file system.
For how to format in the JFS or EXT2/3 file system, refer to
§ 7.6. In addition, the digital receiver can only recognize files
and directories which are named with only alphabetic, numeric
and underscore letters. If there is a file or folder named with
other letters, the digital receiver cannot recognize not only it
but also its subsequent files and folders.
8.4.1
To copy a file to an external hard disk drive
You can copy files to an external hard disk drive.
To copy files, perform the following steps:
1. Connect an external hard disk drive to the digital receiver.
2. Press the
button and then press the
or
button
to select a desird file list except the External list.
8
84
Special Features
3. Put the highlight bar on a desired file and press the F3 button.; then you get asked to select between the built-in
and external hard disk drive.
4. Select External; then the folders are listed.
5. Select a folder and press the OK button; then the selected
file will be copied into the external hard disk drive.
8.4.2
To copy a file from an external hard disk drive
You can copy files from an external hard disk drive.
To copy file, perform the following steps:
1. Connect an external hard disk drive to the digital receiver.
2. Press the
button and then press the
to select the External Device List.
or
button
3. Put the highlight bar on a desired file and press the F3 button.; then the list of folders gets displayed.
4. Select a folder in the built-in hard disk drive.
5. Press the OK button; then the selected file will be copied
into the built-in hard disk drive.
8.5
Playing back contents of YouTube
YouTube is a video sharing website where users can upload,
view and share video files. With the SRP - 2100, you can access
YouTube and play back various contents.
8.6 Sharing image files by Flickr
85
When you select the Entertainment > YouTube, you should see
a screen like the left figure.
To play back a YouTube content,
select a content with the
and
buttons and press the OK button. To play back the content with full screen, press the
OK button again.
You can sort the contents with the option buttons as follows:
• F1 button by most featured
• F2 button by view count
• F3 button from most discussed to least discussed
• F4 button by top favourites
•
button related contents
By pressing the Option button, you can sort the contents by the
updated date, country and quality.
You can also search contents by a specific keyword. To search
contents by a keyword, press the SAT button; then the onscreen keyboard appears. See § 6.3 for how to use the on-screen
keyboard.
To see detailed information about the current one, press the
button. To hide the information box, press the EXIT button.
8.6
Sharing image files by Flickr
Flickr is an image hosting website and on-line community platform. You can search a image file from the network server and
view the file using the Flickr.
8
86
Special Features
To use this function, select the
Entertainment > Flickr.
You can see image files which belong to a specific user by adding
a user. To add a user, perform
the following steps:
1. Press the F1 button, then the on-screen keyboard appears.
2. Enter a desired user name. For how to use the keyboard,
refer to § 6.3.
3. After adding a user, select the user with the
buttons and press the OK button.
and
To delete a user, put the highlight bar on a desired user and
press the F2 button; then you get asked for confirmation. If
you select YES, it will be deleted.
You can also search image files by a specific keyword. To do
that, perform the following steps:
1. Press the F3 button to go to the keyword search mode.
2. Press the F1 button, then the on-screen keyboard appears.
3. Write down a keyword as you desire. For how to use the
keyboard, refer to § 6.3.
4. Select the Save key on the on-screen keyboard to start
searching image files.
To save a image file to the photo album, press the Option button.
For the photo album see § 8.3.
8.7 Weather
8.7
87
Weather
You can view the weather of your city or other cities.
To view the weather, select the
Entertainment > Weather; then
you should see a screen like the
left figure.
To change a city, perform the following steps:
1. Press the F1 button to see additional options.
2. Set the Country and City options as you desire with the
navigation buttons.
3. Press the EXIT button.
Pressing the Option button toggles between the Centigrade and
Fahrenheit.
8.8
Network Game
You can play network game on the digital receiver. You can
play the game by yourself or with others via the network.
8.8.1
To use the wireless keyboard
You can use a wireless keyboard to play the game as well as
the remote control.
8
88
Special Features
To use the wireless keyboard, plug the wireless
module into the USB port on the digital receiver.
NOTE
Use only the provided wireless keyboard. If you use other
wireless keyboard besides the provided one, the digital receiver
may not work properly.
8.8.2
Battle Tank Single Mode
To play the battle tank single mode, select the Entertainment
> Game > Battle Tank (Single); then perform the following
steps:
1.
2.
3.
4.
Select a game mode.
Select a character.
Buy items as you desire.
Select a map. If you play the game by yourself, you do
not need to select a map.
5. Start playing.
If you want to out of the game while palying, press the EXIT button on the remote control or the Esc key on the keyboard.
8.8 Network Game
89
Selecting a game mode
When you select the Entertainment > Game > Battle
Tank(Single), you should see a
screen like the left figure.
You can select a game mode as
you desire. If you want to out of
the game, select the EXIT option.
There are two modes as below:
Single play playing by yourself.
Double play playing with another user.
If you are using the remote control, select a mode with the
and
buttons and press the OK button.
If you are using a keyboard, select a mode with the up and
down arrow keys and press the space bar.
Selecting a character
8
After selecting a game mode,
you should see a screen like the
left figure.
Select a character referring to
Table 8.1.
If you select the ? , a character
will be chosen randomly.
90
Special Features
When you play the game first time, you can select only two
characters. To get a new character, you have to play the single
mode and clear all stages (13 satges).
Table 8.1: Buttons for selection
Remote Control
Action
1 Player
2 Player
Left
Right
Up
Down
Select
OK F2 Keyboard
1 Player
2 Player
Left arrow
A
Right arrow
D
Up arrow
W
Down arrow
Space bar
S
Enter
You can see the selected character’s information of the 1 Player
on the left bottom of the screen. Also you can see the selected
character’s information of the COM or 2 Player on the right
bottom of the screen.
NOTE
You have to select a character in 30 seconds; otherwise, the
character will be selected automatically.
Buying items
After selecting a character, you
should see a screen like the left
figure. Buy a item referring to
Table 8.1.
When you finish selecting items,
select the READY on the screen
as follows:
8.8 Network Game
91
• 1 Player with the remote control : Select the READY
using the MENU button and press the OK button.
• 2 Player with the remote control : Select the READY
using the F1 button and press the F2 button.
• 1 Player with the keyboard : Select the READY using the
Tap key and press the space bar.
• 2 Player with the keyboard : Select the READY using the
Q key and press the Enter key.
Selecting a map
After buying items, you should
see a screen like the left figure.
If you are using the remote control, select a map with the
and
buttons.
If you are using a keyboard, select a map with the left and right
arrow keys.
After selecting a map, select the
START on the screen.
If you are using the remote control, select the START using the
MENU button and press the OK button.
If you are using the keyboard, select the START using the Tap
key and press the space bar.
NOTE
If you play the game by yourself, you do not need to select a
map.
8
92
Special Features
Playing the Battle Tank
When you start the game, you should see a sceen like the
following figure. Play the game referring to Table 8.2.
1
The character’s weapons.
2
The angle of the character.
3
You can see the direction and speed of wind.
4
You can see the information of the character as follows:
ENERGY displays the character’s energy.
POWER displays the power of shot.
MOVE displays the movement bar.
5
You can check your position and enemy’s position on
this mini-map.
6
You can use those items during playing game.
7
Displays current player.
8
Displays the turn time. If the time is over, turn will be
changed to the other player.
8.8 Network Game
93
Table 8.2: Buttons for playing
Action
Changing weapon
Remote Control
3 4 8.8.3
F3 F4
up and down arrows
Changing angle
Moving character
Using items
Skipping turn
Changing view of map
Firing a shot
Keyboard
7 89 0 5 OK left and right arrows
F9 F10 F11 F12
F5
WASD
Space bar
Battle Tank Network Mode
To play the Battle Tank Network Mode, select the Entertainment
> Game > Battle Tank (Network); then perform the following
steps:
1.
2.
3.
4.
5.
Select a game server.
Log on to the game server.
Joining a game.
Selecting a character, map and items for playing.
Start playing.
NOTE
Refer to the BATTLE TANK user guide for how to play the
Battle Tank Network Mode. You can download the guide on
our website. (http://www.i-topfield.com)
8
94
Accessing to The Digital Receiver via The Internet
Chapter 9
Accessing to The Digital
Receiver via The Internet
NOTE
The following section describes complex functions that should
only be used by owners with advanced computer knowledge.
SRP - 2100 provides a web service and FTP service. You can
make scheduled recordings or download recording files to your
computer via these services. Here you need a router, which
will connect the digital receiver to your computer or to the
Internet. To use the network features of the digital receiver,
you should take the following steps:
1. Configuring your router for the digital receiver.
2. Configuring the Local Area Network (LAN) settings on
the digital receiver.
3. Accessing the home page of the digital receiver. Refer to
§ 9.3 for detailed description about things you can do by
way of the web service of the digital receiver.
9.1 Configuring the router
95
4. Accessing the FTP Server of the digital receiver.
NOTE
The web server and FTP server of the digital receiver do not
work in standby mode. So it must be powered up at all times if
you wish to use the web service at any time.
9.1
Configuring the router
In this section, the setup program of WRT54G, which is a router
manufactured by Linksys, will be referred to as an example of
how to configure the router for network access.
NOTE
For detailed description about how to set up the router, refer
to the manual of your router.
9.1.1
To access within the local area network
Once your router is powered up, a local area network gets
created whether or not it is connected to the Internet.
You can let the router automatically assign a dynamic IP address to the computers or devices connected to the network by enabling the DHCP server of
the router. In this case, you can access
the digital receiver with the IP address
which is assigned to the digital receiver
by the router.
If the digital receiver reboots, a new dynamic IP address will be
assigned to it. You had better assign a static IP address to the
digital receiver to avoid this inconvenience. For how to assign
a static IP address, refer to the manual of your router. For how
to specify a static IP address on the digital receiver, see § 9.2.
9
96
Accessing to The Digital Receiver via The Internet
9.1.2
To access over the Internet
When you are away from home, you can access the digital
receiver inside your home if your router is configured to route
access to the digital receiver by means of port forwarding. Via
this feature, your router will lead you to the digital receiver
when you access your router with its IP address.
Your router may be assigned to a dynamic IP address by an
Internet service provider. So if the router has rebooted, you
cannot access it unless someone in your home can inform you
of the changed IP address. However, many routers support
Dynamic Domain Name System (DDNS) service, which can
settle this problem. The following image is an example of one
such DDNS service provider.
If you use a DDNS service, you can access your router with
a domain name. The instructions on how to use the DDNS
service are as follows:
9.2 Configuring the network settings on the digital receiver
97
1. Make an account on a web site providing DDNS service,
which should be supported by your router.
2. Configure your router with the account so that it can
communicate with the web site.
Whenever a new dynamic IP address is assigned to the router,
it will inform the DDNS service provider of the new IP address.
This makes it possible that you access the router with a domain
name at any time.
9.2
Configuring the network settings on the digital receiver
You should configure the LAN settings to enable the web service and FTP service.
Select the Installation > Network
Setting > IP Setting menu.
9
You may get the digital receiver to be assigned a dynamic IP
address. If so, set the Connection Type option to DHCP.
98
Accessing to The Digital Receiver via The Internet
You can view the dynamic IP address assigned to the digital
receiver by your router at the IP Setting menu.
Sometimes when the digital receiver is restarted, the dynamic
IP address will be changed and you will have to check it at the
IP Setting menu to access the digital receiver. To avoid this
cumbersome thing, you had better assign a static IP address
rather than dynamic one.
To assign a static IP address, set the Connection Type option to
Static, then the IP Address, Subnet Mask, Gateway, Primary
DNS and Secondary DNS options become enabled. You have
to set these options to match with the configuration of your
router.
9.3
Accessing the web server
To Access to the web server, set the Installation > Network
Setting > Web Server option to Enable.
Select the Installation > Network Setting > User Info menu. At
this time, you have to enter Personal Identification Number
(PIN). Then, set the User ID and Password options as you
desire. And select OK to save the settings. When you access
to the web server, you will be asked for the account that was
made with these options.
In way of the web server of the digital receiver, you can do the
following:
• Download recording files.
• Create new recording timers.
• View information about the programme currently being
recorded.
• View the system information of the digital receiver.
9.3 Accessing the web server
99
NOTE
It is recommended using the Internet Explorer web browser in
order to fully enjoy the features. If you use a different web
browser such as Netscape Navigator, some problems may occur.
To access the digital receiver’s home page through your web
browser, enter its IP address, or domain name if you use a
DDNS service. For the DDNS service, refer to the user manual
of your router.
You cannot only download but also upload recording files or
MP3 files in the File Management page. However, if you wish
to download or upload a file of which size is 2 gigabyte or
more, it is recommended using the FTP server rather than the
web server.
9
100
Accessing to The Digital Receiver via The Internet
NOTE
The maximum number of user connections is one. This means
that you cannot access the web server while someone else is
occupying it.
9.4
Accessing the FTP server
To Access to the FTP server, set the Installation > Network
Setting > FTP Server option to Enable.
Select the Installation > Network Setting > User Info menu. At
this time, you have to enter Personal Identification Number
(PIN). Then, set the User ID and Password options as you
desire. And select OK to save the settings. When you access
to the FTP server, you will be asked for the account that was
made with these options.
9.4 Accessing the FTP server
101
NOTE
You can access the FTP server with an anonymous account.
However, with an anonymous account you can only download
files. You cannot upload files.
You need an FTP client program to access the FTP server of the
digital receiver.
You can log into the FTP server with the user name and password specified in the Installation > Network Setting > User
Info menu.
9
102
Accessing to The Digital Receiver via The Internet
NOTE
The maximum number of user connections is one. This means
that you cannot access the FTP server while someone else is
occupying it.
103
Chapter 10
Firmware Update
The digital receiver has a stable and convenient firmware to
use. However, once in a while a new firmware may be released
to improve performance. You can get the latest firmware and
a firmware update tool, which runs on most versions of Windows, from the Topfield web site, http://www.i-topfield.
com.
10.1
Checking the firmware information
You have to check the firmware
information of your digital receiver before downloading a
new firmware. Select the Information > System Status menu.
You should see a screen like the
left figure.
Remember the number of the
System ID item, and download
the latest firmware with the
same system identification.
10
104
Firmware Update
NOTE
It is only allowed to update with the firmware of which system
identification is identical to that of yours. Otherwise you will
fail to update a firmware.
Please check for your relevent firmware under your model
number on the web site.
10.2
From a USB memory
If you have a USB memory stick, you can update the firmware
from it by performing the following steps:
1. Download a new firmware from the Topfield web site.
2. Copy the firmware file to your USB memory
stick.
3. Insert the USB memory stick into the USB
port of the digital receiver.
4. Select the Installation > Firmware Upgrade
> USB Firmware Upgrade menu, then the
files in the USB memory are listed.
5. Place the highlight bar on the right
firmware file and press the OK button, then
a countdown will be displayed on the front
display of the digital receiver.
6. When the ‘END’ message appears, restart
the digital receiver.
10.3
From the firmware server via the network
You can update the firmware from the firmware server which
is run by Topfield via the network. Make sure that the digital
10.3 From the firmware server via the network
105
receiver is connected to your router before configuring the
network settings on the digital receiver.
NOTE
For detailed description about how to set up the router, refer
to the manual of your router.
Select the Installation >
Firmware Upgrade > Network
Firmware Upgrade menu.
You should see a screen like the
left figure.
To enable the digital receiver to update the firmware automatically when a new firmware is available, set the Automatic
Upgrade option to Enable.
Otherwise if you want to do that by yourself, select the Start
firmware upgrade option; then you get asked for confirmation. If you select Yes, it checks up whether a new firmware is
available, and if any, it will start firmware update.
To change the update server name, press the OK button at the
Update Server option; then, the on-screen keyboard appears.
See § 6.3 for how to use the on-screen keyboard.
You can get the server name from the web site, http://www.
i-topfield.com.
10
106
10.4
Firmware Update
Over the air
You can get a new firmware
over the air. Select the Installation > Firmware Upgrade > OTA
Firmwrae Upgrade menu.
You should see a screen like the
left figure. Selecting the Start option starts firmware update.
Satellite
Frequency
Symbol Rate
Polarisation
PID
Astra (19.2° E)
12603 MHz
22000 KS/s
Horizontal
347
On the left table is presented
the transponder information
appointed by the manufacturer, Topfield, for firmware
update.
This transponder information can be changed. You can get the
information from the web site, http://www.i-topfield.com.
107
Appendix A
Universal Remote Control
The universal remote control allows you to operate the most
important functions such as volume control on your television,
audio system, or DVD player. To be able to control the device,
you must adapt the remote control to the device first.
Take the following steps:
1. Turn on the device you want to operate.
2. Point the remote contorl at the remote senser on the device.
3. Hold down the OK and device button simultaneously
for two seconds until LED lamp flashes on. For example,
if you want to operate your television with the remote
control, press the OK and TV buttons simultaneously.
4. Find the manufacturer of the device from the codes list.
5. Enter the three-digits code you have found for your de
vice and press the OK button.
6. If the setting is finished correctly, LED lamp blinks twice
and the device will be turned off. Otherwise, repeat from
the step 2.
If you cannot find a code for your device, do as follows:
A
108
Universal Remote Control
1. Turn on the device you want to operate.
2. Point the remote contorl at the remote senser on the device.
3. Hold down the OK and device button simultaneously
for two seconds until LED lamp flashes on. For example,
if you want to operate your television with the remote
control, press the OK and TV buttons simultaneously.
4. Press the CHANNEL+ or CHANNEL− button until the device turns off.
If you want to find out the number which you set for your
device, do as follows:
1. Hold down the OK and device button simultaneously
for two seconds. For example, if you want to know the
number which you set for your television, press the OK and TV buttons simultaneously.
2. Press the
button. Then LED lamp will show the
number with blinks. For example, if the number is 3,
LED lamp will blink three times. In case of 0, LED lamp
will blink ten times.
You can reset the settings. To do that, do as follows:
1. Hold down the TV and 0 buttons simultaneously for
more than five seconds.
2. Each device button blinks three times in the following
order: TV → STB → DVD → AUX 3. After that, all settings will be reset to the manufacturer’s
factory settings.
109
NOTE
If your device code is not listed on the following pages, you
will not be able to use this remote as a universal remote for
your specific device.
A
110
Universal Remote Control
A.1
TV codes list
A
ACCENT
049, 063
ACEC
112
ACURA
195
ADMIRAL
065, 076, 163, 171,
190, 307, 324, 369
ADYSON
379
AGASHI
076, 379
AGEF
324
AIKO
049, 063, 076, 102,
141, 172, 195, 225,
379
AIM
049, 063
AIWA
376, 377
AKAI
019, 049,
063, 076,
123, 133,
150, 172,
195, 209,
333, 379,
433, 437
050,
102,
139,
174,
225,
428,
055,
107,
141,
182,
326,
432,
AKIBA
006, 049, 063, 123,
380
AKITO
049, 063, 106
AKURA
006, 049, 076, 096,
123, 195, 419, 426
ALARON
042, 334
ALBA
018, 044, 049,
107, 123, 134,
179, 184, 195,
228, 232, 239,
413, 421, 431
050,
163,
225,
379,
AMPLIVISION
113, 379, 421, 425
AMSTRAD
004, 011, 049, 063,
076, 123, 131, 172,
195, 225, 426
ANAM
049, 063, 195
ANGLO
076, 195
ANITECH
049, 063, 076, 195,
407
ANSONIC
045, 049, 063, 107,
112, 195, 210, 242,
391, 413, 421
APOLLO
165
ARC EN CIEL
029, 034, 074, 182,
186, 415, 424
ARCAM
029, 379, 424
ARDEM
392
ARISTONA
049, 050, 063, 065,
079, 112, 158, 160,
188
A.R.SYSTEM
049, 063
ARTHUR MARTIN
075, 107, 127, 133,
136, 139, 148, 153,
307, 425
ASA
003, 020,
080, 091,
171, 197,
319, 324,
406, 408
ASBERG
049, 063, 407
ASORA
195
ASTRA
195
ASUKA
006, 050, 076, 123,
379
ATLANTIC
049, 050, 063, 113,
236, 242, 379
ALBIRAL
121, 326, 372
ALCYON
407
ALLORGAN
050, 094, 236, 334
ATORI
195
ALLSTAR
049, 063
AUCHAN
107, 425
065,
117,
235,
341,
078,
146,
307,
375,
A.1 TV codes list
AUDIOSONIC
031, 049, 063, 074,
076, 195, 213, 379,
392, 421
AUDIOTON
050, 076, 379, 392,
421
AUSIND
075, 090, 407
AUTOVOX
050, 071, 078,
080, 083, 090,
156, 236, 254,
319, 323, 324,
407, 413, 416
AWA
AYOMI
079,
147,
305,
379,
BLACKTRON
111
006
BLACKWAY
006
BLAUPUNKT
019, 053, 057, 060,
113, 118, 244, 245,
246, 247, 248, 249,
308
BLUE SKY
006, 049, 063, 123,
195, 232
BLUE STAR
006
BONDSTEC
413
BOOTS
050, 106, 379
018, 049, 063, 131,
195, 206, 320, 379,
426, 433
BPL
006, 049, 063
BRANDT
074, 182, 218, 415,
424, 436
411
BRANDT ELECTRONIQUE 029, 034, 074, 182,
186
B
BRINKMANN
049, 063, 163
BRION VEGA
049, 063, 065, 083,
167, 172, 173, 181,
196, 324, 356
BAIRD
074, 102, 182, 209,
321, 329, 379, 409
BANG & OLUFSEN
324
BRITANNIA
379
BARCO
107, 355, 371, 372,
422
BROTHER
076
BRUNS
056, 065, 324
BASIC LINE
006, 031, 049, 107,
123, 159, 195, 207,
226
BSR
094, 107, 110, 139,
168, 314
BASTIDE
379
BAUR
012, 049, 053, 063,
107, 150, 172, 244,
245, 246, 247, 301,
357, 414, 416
BAZIN
379
BEKO
063, 184, 240, 241,
392, 421, 433
BEON
049, 063, 163
BEST
213, 421
BESTAR
BTC
123
BUSH
006, 018, 049, 076,
094, 106, 107, 123,
134, 139, 142, 143,
172, 179, 195, 209,
223, 225, 226, 232,
239, 307, 379, 416
BUSH(UK)
107, 147, 168
A
C
CAPSONIC
076
CARAD
049, 063
049, 063, 421
CARENA
049, 063, 380
BINATONE
379
CARREFOUR
018, 406
BLACK STAR
413
CARVER
177
112
Universal Remote Control
CASCADE
049, 063, 064, 195
CASIO
049, 063
CROWN
049, 063, 154, 163,
170, 195, 209, 232,
372, 407, 419, 421,
431
CATHAY
049, 063
CCE
049, 063, 379
CS ELECTRONICS
031, 123, 379, 413
CENTURION
049, 063
CTC
413
CENTURY
044, 054, 065, 163,
189, 324, 411, 413
CTC CLATRONIC
045
CURTIS MATHES
126, 190, 212
002,
093,
139,
189,
421
CYBERTRON
123
CGE
044,
094,
142,
369,
054,
096,
163,
407,
090,
107,
168,
413,
D
DAENYK
042
DAEWOO
063, 123, 140, 145,
161, 193, 195, 379
CIHAN
111
CIMLINE
031, 123, 134, 195
DAINICHI
123, 379
CITY
195
DANSAI
CLARIVOX
056, 121, 125, 163,
406
063, 076, 141, 195,
379
DANSETTE
426
DANTAX
392, 421
DATSURA
209
DAWA
049, 063
DAYTRON
049, 063, 195, 226
DE GRAAF
023, 107, 122, 139,
209, 307
DECCA
049, 063, 102, 106,
111, 120, 200, 331,
379
CLATONIC
076, 123
CLATRONIC
031, 045, 049, 063,
076, 113, 123, 195,
225, 379, 407, 413,
421, 431
CMS HIGHTEC
379
COMTEL
111, 125
CONCORDE
195
CONDOR
006, 045, 049, 050,
063, 113, 163, 195,
210, 379, 413, 421
DECCA(UK)
046, 050, 102, 106,
131
DEITRON
049, 063
018, 131, 195, 206,
302, 320, 379
DENKO
076
DENON
126, 212
029, 034, 074, 182,
186, 232, 415, 424
DER
321
DERWENT
105
COSMEL
195, 213
DESMET
049, 063, 113
CROSELY
044
DIAMANT
049, 063
DIGILINE
049, 063
DIXI
063, 195, 379, 413
DOMLAND
423
CONTEC
CONTINENTAL EDISON
CROSLEY
054, 065, 090, 093,
094, 104, 107, 139,
324, 407, 413
A.1 TV codes list
DORIC
104, 105
DREAN
049, 063
113
EMERSON
004, 006, 042, 044,
049, 063, 065, 113,
225, 324, 327, 406,
413
DTS
195
DUAL
049, 050, 063, 095,
107, 139, 156, 168,
182, 242, 243, 379,
414, 416, 423, 424
EMPEROR
006
ERRES
063, 112
ESC
049, 063
DUAL-TEC
195, 168, 050, 040
ETRON
DUMONT
045, 065, 080, 102,
139, 146, 319, 324,
339, 341, 375, 379,
406, 408
049, 063, 107, 139,
195
DUMONT-FINLUX
020, 045, 061, 075,
078, 091, 104, 117,
147
DUX
049, 063, 112
DYNATRON
049, 063
E
EURO-FEEL
076
EUROMANN
049, 063, 076, 379,
421
EUROPA
049, 063
EUROPHON
044, 045, 046, 049,
050, 063, 068, 107,
120, 168, 318, 336,
379, 413
EXPERT
107, 236, 242, 425
EXQUISIT
049, 063, 413
049, 063, 107, 121,
123, 172, 194, 210,
242, 337, 368, 369,
391, 411, 421, 435
F
ELBIT
111
ELCIT
045, 046, 047, 062,
065, 104, 107, 150,
168, 324, 413
ELECTA
006, 076
ELECTRO TECH
195
ELEKTA
006, 076
ELEKTRONSKA
318
ELG
049, 063
ELIN
003, 020, 049, 063,
107, 139, 172, 195,
379, 408, 416
ELBE
ELITE
031, 049, 063, 123
ELMAN
045, 168
ELTA
076, 195, 379
FAMILLY LIFE
049, 063
FENNER
063, 195
FERGUSON
001,
074,
102,
182,
245,
319,
329,
436
FIDELITY
049, 050, 063, 076,
107, 158, 225, 307,
364, 379
FIDELITY(UK)
133
FILSAI
050, 379
FINHER
359
FINLANDIA
033, 122, 139, 172,
197, 209, 223, 307,
375, 419
032,
076,
103,
204,
246,
321,
344,
050,
080,
121,
218,
251,
322,
409,
073,
082,
158,
244,
306,
328,
411,
A
114
Universal Remote Control
FINLUX
FIRST LINE
FISHER
FLINT
003, 020, 042,
049, 061, 063,
078, 080, 090,
102, 104, 107,
139, 146, 147,
197, 210, 235,
324, 339, 341,
379, 406, 407,
428, 429, 437
045,
075,
091,
117,
163,
319,
375,
408,
045, 049, 063, 094,
102, 107, 134, 139,
191, 195, 209, 210,
379, 411, 413, 416
018, 041, 050, 056,
065, 069, 102, 104,
107, 117, 139, 143,
156, 172, 189, 206,
209, 320, 324, 379,
408, 414, 416, 421
031, 049, 063, 102,
123, 379, 380
GALAXIS
045, 049, 063, 163,
421
GBC
031, 104, 107, 139,
143, 168, 195
GE
006, 074, 182, 218
GEANT CASINO
107, 425
GEC
049, 063, 102, 104,
107, 120, 171, 172,
192, 307, 379, 416
GEC(UK)
046, 050, 102, 107,
150, 162, 192
GELOSO
031, 047, 062, 104,
107, 139, 168, 171,
195, 307, 413
GENERAL
064, 074, 182
GENERAL TECHNIC
195
GENEXXA
049, 063, 123, 307,
426
GOLDHAND
379
GOLDLINE
213
GOODMANS
018,
102,
143,
218,
428
FNR
045
FORGESTONE
158
FORMENTI
090, 107, 113, 139,
307, 324, 379, 407
FORMENTI-PHOENIX
050, 075, 104, 113,
148, 307
GORENJE
124, 189, 421
FORTRESS
190, 324
GPM
123
GRADIENTE
049, 063, 170, 177
GRAETZ
049, 063, 090, 104,
136, 139, 153, 159,
162, 171, 172, 198,
225, 307
GRANADA
013, 018, 033, 041,
063, 102, 104, 105,
112, 120, 148, 164,
165, 171, 209, 218,
237, 238, 240, 241,
252, 307, 325, 363,
379, 407, 418, 419
GRANADA(UK)
046, 050, 090, 107,
139, 143, 162, 307
FRABA
049, 063, 421
FRIAC
045, 049, 063, 195
FRONTECH
076, 139, 195, 307,
379, 413, 416
FUJITSU
042, 045, 102, 107,
195, 236, 327, 379
FUJITSU GENERAL
195, 379
FUNAI
042, 076, 094, 314,
327
G
GALAXI
045, 049, 063
042,
134,
155,
225,
063,
139,
182,
232,
076,
141,
195,
379,
A.1 TV codes list
GRANDIN
006, 031, 049, 063,
107, 113, 123, 195,
379, 380, 425, 431,
435
GRONIC
045
GRUNDIG
005, 019, 049,
063, 080, 090,
115, 118, 166,
244, 245, 246,
248, 249, 308,
341, 406, 407
115
HINARI
004, 018, 042,
066, 094, 107,
123, 133, 134,
143, 179, 195,
232, 307, 327
HISAWA
006, 031, 123, 380,
425
HIT
342
HITACHI
007, 009,
023, 033,
063, 074,
104, 107,
127, 139,
162, 168,
182, 185,
212, 218,
307, 309,
334, 344,
416, 418
HITASHI FUJIAN
013, 164, 252
HITSU
123, 195, 379
HORNYPHON
049, 063, 112
HOSHAI
123, 379
045, 046, 049, 063,
195
HUANYU
379
HYGASHI
379
HANTOR
049, 063
HYPER
HARLEY DAVIDSON
042
050, 168, 195, 254,
361, 379, 413
HYPERSONIC
172
HARWOOD
049, 063, 195, 426
HYPSON
HAUPPAUGE
049, 063
006, 049, 063, 076,
379, 380, 411, 425
HCM
006, 031, 049, 063,
076, 123, 163, 195,
379, 426
053,
101,
232,
247,
340,
H
HALIFAX
076, 379
HAMPTON
379
HANIMEX
094
HANSEATIC
006, 018,
063, 094,
113, 143,
324, 379,
421, 423
HANTAREX
049,
104,
172,
391,
050,
107,
195,
416,
018,
049,
086,
110,
143,
171,
186,
231,
315,
361,
049,
119,
139,
209,
020,
050,
102,
126,
150,
176,
192,
304,
333,
379,
I
IBERRIA
049, 063
ICE
049, 063, 076, 123,
195, 225, 379
HEMA
195, 379
HEMMERMANN
150, 416
ICES
123, 379
HIFIVOX
029, 034, 074, 182,
186, 304, 424
IMPERIAL
HIGASHI
050
HIGHLINE
049, 063, 076
002, 044, 049, 054,
063, 090, 093, 094,
107, 142, 163, 168,
189, 301, 307, 369,
407, 413, 416, 421
HIKONA
123
INDIANA
049, 063
A
116
Universal Remote Control
INGELEN
090, 104, 136, 139,
153, 159, 162, 171,
198, 232, 435
INGERSOL
195
INNO HIT
044, 046, 049, 050,
063, 066, 102, 123,
155, 195, 217, 379,
407, 413
INNOVATION
049, 063
INTERACTIVE
210
INTERBUY
076, 195, 413
INTERFUNK
049, 063, 065, 067,
074, 090, 104, 107,
112, 139, 150, 153,
159, 172, 182, 301,
302, 324, 363, 421
INTERVISION
006, 045, 049, 055,
063, 076, 107, 123,
225, 232, 378, 379,
380, 381, 382, 384,
385, 386, 387, 388,
389, 413, 421, 423
350, 375, 416, 428,
433, 435, 437
ITV
049, 063, 076, 413
J
JEAN
018
JEC
141
JET POINT
365
JVC
018, 103, 123, 129,
143, 158, 170, 174,
182, 225, 364, 409,
433
K
KAISUI
006, 031, 049, 050,
063, 123, 195, 207,
379, 380
KAMOSONIC
050
KAMP
379
KAPSCH
107, 172, 236, 242,
408
KARCHER
003, 006, 020, 031,
045, 049, 050, 063,
068, 076, 107, 195,
207, 217, 421, 435
IRRADIO
031, 049, 063, 066,
075, 090, 123, 155,
195, 254, 407, 413
ISUKAI
006, 049, 063, 123
KATHREIN
124
ITC
379
KAWASHO
379
ITS
006, 031, 049, 063,
076, 123, 225, 379
KB ARISTOCRAT
107
KENDO
042, 090, 107, 117,
134, 139, 150, 157,
159, 162, 165, 171,
172, 193, 197, 198,
209, 301, 307, 343,
350, 375, 416, 428
044, 045, 049, 055,
063, 134, 172, 210,
413, 421, 435
KENNEDY
071, 079, 104, 107,
139, 236, 305, 323,
369
KINGSLEY
379
KLARMAX
371, 372
KNEISSEL
049, 063, 210, 242,
369, 391, 411, 421,
435
KOLSTER
045, 049, 063, 416
ITT
ITT-NOKIA
042,
107,
139,
162,
185,
209,
090,
117,
150,
165,
193,
301,
097,
134,
153,
171,
197,
307,
104,
136,
159,
172,
198,
343,
A.1 TV codes list
KONKA
031, 049, 063, 123,
225, 232
KORPEL
049, 063
KORTING
027, 065, 094, 113,
324, 421
KOSMOS
049, 063
KOTRON
076, 426
KRAKING
411
KRIESLER
050, 063, 065, 079,
112, 158, 160, 188
117
LOEWE OPTA
035, 046, 049, 052,
063, 065, 120, 144,
213, 324
LOGIC
331
LOGIK
032, 131, 158, 225,
364
LOGIX
195
LUMA
063, 107, 110, 133,
171, 172, 195, 210,
236, 242, 307
LUMATRON
049, 063, 076, 107,
172, 236, 242, 329,
379
KTV
050, 379
KYOSHU
076, 163
LUX MAY
049, 063, 195
KYOTO
107
LUXOR
KYUSHU
426
042, 050, 090,
122, 127, 133,
150, 155, 159,
172, 185, 197,
307, 312, 330,
418, 428, 429
LYCO
076
L
107,
139,
165,
209,
416,
LECSON
049, 063
LEMAIR
210
LENCO
049, 063, 107, 195,
408
M
M ELECTRONIC
003, 235, 375
LENOIR
050, 195
MAAZ
371, 372
LESA
413
MADISON
049, 063
049, 063, 076, 094,
102, 431
MAGNADYNE
045, 046, 047, 062,
065, 104, 107, 120,
139, 150, 168, 318,
324, 413
MAGNAFON
045, 046, 050, 068,
075, 090, 120, 235,
336, 379, 407
MAGNAVOX
018, 042, 049, 063
MANDOR
076
LEYCO
LEYEO
076
LG(GOLDSTAR)
023, 049, 050,
063, 107, 139,
155, 168, 172,
202, 203, 219,
379, 413, 421
055,
152,
195,
254,
LIESENKOTTER
049, 063, 112
MANESTH
LIFETEC
049, 063, 076, 123,
195
063, 076, 094, 113,
134, 141, 379
MANHATTAN
049, 063, 195
LLOYD’S
195
MARANTZ
063
LOEWE
049, 063, 089, 324,
391, 421
MARELLI
324
MARK
063, 195, 379
A
118
Universal Remote Control
MASUDA
123, 195, 225
MATSUI
001, 004, 018, 041,
049, 050, 063, 094,
100, 102, 106, 107,
131, 134, 141, 143,
150, 171, 179, 180,
195, 209, 218, 225,
229, 232, 244, 245,
246, 307, 314, 331,
379, 380, 416, 431
157, 164, 183, 190,
244, 245, 246, 252,
326, 330, 331
MIVAR
043, 046, 050, 058,
072, 081, 090, 120,
155, 318, 337, 379,
391, 407, 421, 434
MONACO
195
MORGAN’S
049, 063
407
MAXIMAL
119, 139
MOTION
MAXWELL
371, 372
MOTOROLA
190
McMICHAEL
192
MTC
MEDIATOR
049, 063, 112
049, 063, 379, 416,
421
MEDION
049, 063, 195
MTEC
106
MEGAS
435
MULTISTANDARD
045
MEGATRON
126, 212
MULTITEC
049, 063, 195
MELECTRONIC
003, 049, 063, 074,
182, 195, 210, 375,
379, 408, 413, 416,
428, 429
MULTITECH
031, 045, 046, 049,
050, 063, 120, 189,
195, 379, 392, 413,
416, 421
MELVOX
425,
MURPHY
MEMOREX
099, 195
102, 104, 105, 107,
117, 171, 254, 307,
379, 408
MEMPHIS
102, 195, 213
MURPHY(UK)
MERCURY
049, 063, 195
162
METZ
019, 049, 051, 053,
065, 067, 070, 092,
118, 244, 245, 246,
247, 324, 412
MUSIKLAND
123
MICROMAXX
049, 063, 195
MINERVA
019, 053, 080, 090,
118, 232, 244, 245,
246, 247, 248, 249,
340, 341, 406, 407
N
NAD
172, 209
NAIKO
049, 063
NAKIMURA
049, 063
NAONIS
036, 040, 071, 079,
110, 171
MINOKA
049, 063, 419, 426
NAT
085, 149, 151
MISTRAL
158
NATIONAL
033, 085, 104
MITSUBISHI
013, 018, 019, 021,
049, 063, 065, 105,
124, 131, 132, 143,
NEC
018, 049, 063, 113,
131, 143, 177, 195,
379, 380
A.1 TV codes list
NECKERMANN
002, 012, 049,
063, 065, 107,
139, 163, 180,
210, 247, 250,
312, 324, 357,
413, 416, 421
NEDIATOR
063
NEI
063, 125, 225
NESCO
042, 413
NETSAT
049, 063
NETWORK
NEUFUNK
050,
133,
189,
307,
379,
NOVATRONIC
119
003, 020, 049, 063
O
OCEANIC
086, 094, 104, 107,
108, 109, 116, 139,
159, 172, 209, 425
OCEANIC(F)
150
ODEON
076
OKANO
049, 063, 076, 102,
421
213
OMEGA
076
049, 063, 195, 435
ONCEAS
050
NEW WORLD
123
ONWA
031, 123, 225, 432
NEWTECH
049, 050, 063, 182,
195, 379
OPERA
049, 063
OPTIMUS
099, 315
NICAMAGIC
379
OPTONICA
190
NIKKAI
018, 049, 063, 076,
102, 123, 139, 141,
195, 213, 379
ORBIT
049, 063
ORION
004, 042, 045,
051, 063, 076,
113, 131, 134,
150, 179, 191,
199, 216, 314,
366, 367, 426
ORLINE
049, 063, 123
ORMENTI-PHOENIX
104
029, 034, 074, 182,
186, 424
ORMOND
195
OSAKA
066
090, 104,
134, 136,
153, 157,
165, 171,
197, 198,
307, 330,
416, 419,
433, 437
OSAKI
049, 063, 066, 076,
102, 106, 123, 379,
426
OSIO
049, 063, 155
OSO
123
OSUME
018, 102, 123, 302
OTTO VERSAND
012, 018, 049, 050,
053, 063, 074, 094,
104, 107, 113, 134,
139, 143, 172, 190,
244, 245, 246, 247,
250, 312, 357, 362,
379, 413, 414, 416
NIKKIA
066
NOBLEX
049, 063, 076, 359,
360
NOBLIKO
044, 045, 050, 075,
080, 090, 235, 379,
406, 407
NOGAMATIC
NOKIA
NORDMENDE
107,
139,
159,
172,
209,
343,
428,
017, 029, 034,
049, 063, 074,
130, 150, 165,
182, 186, 218,
245, 246, 304,
333, 334, 424
117,
150,
162,
193,
301,
350,
429,
038,
083,
174,
244,
307,
049,
094,
139,
195,
331,
A
120
Universal Remote Control
P
P.T ACTRON
221, 247, 250, 313,
324, 337, 342, 350,
363, 374, 427
111
PAEL
050, 075, 379
PALLADIUM
012, 049, 063, 107,
163, 210, 247, 324,
357, 379, 413, 416,
421
PALSONIC
049, 055, 063, 076,
379, 426
PANAMA
049, 063, 076, 195,
379, 413
PANASONIC
049, 063, 099, 104,
107, 137, 139, 149,
151, 172, 397, 398,
400, 401, 405
PANAVISION
049, 063, 210
PATHE CINEMA
107, 113, 121, 379,
391, 411, 416, 425
PATHE CINEMA(F)
PATHE MARCONI
PAUSA
050, 168
029, 034, 074, 182,
186, 415, 424
PHOENIX
049, 050, 063, 075,
102, 104, 107, 113,
148, 324, 379, 392,
421
PHONOLA
022, 050, 063, 065,
079, 112, 158, 160,
188, 250, 324, 379
PILOT
049, 063
PIONEER
049, 063, 074, 172,
182, 209, 218, 227,
307, 421, 427
PIONIER
392, 421
PLANTRON
049, 063, 076, 195
PLAYSONIC
379
POLICOM
074
POPPY
195
POWERPOINT
232
PRANDONI-PRINCE
044, 046, 075, 090,
120, 171, 172, 307,
407, 413
195
PAUZA
195
PRECISION
379
PERDIO
049, 063, 102, 107,
113
PREMIER
142
PRIMA
076, 195, 307
PRINCE
044, 046, 075, 171
PRINZ
102, 185, 416
PROFEX
107, 139, 195
PROFI-TRONIC
045, 049, 063
PROLINE
030, 049, 102, 112,
191, 366, 436
PROSONIC
049, 063, 085, 149,
151, 195, 225, 379,
421, 431
PROTECH
045, 063, 076, 139,
163, 195, 379, 413,
416
PROVISION
049, 063
PERFEKT
049, 063
PERSHIN
425
PHILCO
002, 016, 044,
054, 063, 065,
093, 094, 104,
126, 142, 163,
189, 212, 324,
407, 413, 421
PHILHARMONIC
379
PHILIPS
015,
063,
111,
160,
192,
022,
065,
112,
175,
215,
049,
079,
157,
182,
217,
049,
090,
107,
168,
369,
050,
089,
158,
188,
220,
A.1 TV codes list
PYE
PYMI
050, 063, 065, 079,
112, 157, 158, 160,
188, 250
RANK
147, 406
RBM
341
RBM(UK)
147
049, 063, 112, 195,
324
RCA
190, 218, 436
RECOR
049, 063
Q
RECTILIGNE
049, 063
REDIFFUSION
018, 059, 105, 139,
171, 172, 307, 343
QUADRA VISION
425
QUASAR
045, 046, 068, 075,
099, 155, 413
REDIFFUSION(UK)
150, 162
REDIFUSION
104, 105
003, 018,
049, 050,
074, 075,
080, 090,
113, 115,
131, 139,
150, 153,
195, 206,
245, 246,
301, 319,
341, 379,
413, 416
REDSTAR
049, 063
REFLEX
049, 063
QUELLE
QUESTA
019,
053,
076,
091,
117,
146,
155,
235,
247,
320,
406,
020,
063,
078,
094,
118,
147,
172,
244,
254,
340,
408,
018
R
RADIALVA
RADIOLA
RADIOMARELLI
RADIONETTE
REVOX
049, 063, 421
REX
036, 040,
079, 095,
171, 210,
243, 305,
338, 413
RFT
076, 102, 390, 391,
392, 393, 394, 395,
421
R-LINE
049, 063
ROADSTAR
031, 049, 063, 076,
163, 195
063,
107,
236,
307,
ROBOTRON
056, 065, 324
049, 063, 074, 107,
123
RODEX
049, 063
ROTEL
302
050, 063, 065, 079,
112, 158, 160, 188,
250, 342
ROWSONIC
050
ROYAL LUX
421, 426
RTF
056, 065
045, 046, 047, 062,
063, 065, 104, 105,
150, 168, 324, 413
121
071,
110,
242,
323,
S
SABA
014, 017, 029, 034,
038, 046, 065, 074,
077, 107, 120, 133,
139, 172, 182, 186,
218, 304, 307, 324,
333, 334, 424, 436
003, 020, 117, 150
RADIO SHACK
049, 063
RADIOTONE
049, 063, 076, 163,
195, 421, 426, 431
RAMK
341
SACCS
121
RANDT
029
SAGEM
006, 380, 435
A
122
Universal Remote Control
SAISHO
004, 050, 076, 084,
107, 131, 132, 134,
179, 195, 233, 307,
330, 331, 379
SALORA
033,
133,
150,
185,
307,
419
075,
136,
153,
198,
312,
107,
139,
171,
209,
416,
127,
148,
172,
301,
418,
SAMBERS
045, 046, 068, 075,
090, 120, 155, 336,
407
SAMSUNG
050, 063, 066, 076,
102, 155, 189, 195,
217, 359, 360, 365,
379, 421
243, 250, 307, 328,
342, 379, 413, 414,
416, 423
SCOTT
042, 327
SEARS
042
SEG
018, 045, 049, 050,
056, 063, 076, 107,
172, 195, 232, 379,
413
SEI
004, 045, 049, 051,
063, 094, 107, 139,
236, 314, 324, 357,
416
SEL SINUDYNE
250
SELECO
036, 040, 063, 071,
079, 095, 107, 110,
171, 172, 210, 236,
242, 243, 305, 307,
323, 338, 339, 369
SANDRA
379
SANELA
411
SANSUI
049, 063, 225
SENCORA
195
195
SENTRA
123, 139, 141, 195
003,
049,
065,
131,
198,
302,
351,
421
SERINO
380, 435
SHARP
018, 094, 143, 170,
190, 206, 214, 302,
362, 364
SHORAI
042, 094
SIAM
049, 063
SIAREM
045, 046, 065, 104,
107, 120, 139, 324
SICATEL
121
SIEMENS
003, 018, 019,
049, 053, 063,
113, 118, 206,
245, 246, 247,
249, 302, 307
SIERA
050, 063, 065, 079,
112, 158, 160, 188
SIERRA
049, 063, 112
SIESTA
421
SILVA
049, 063, 379
SANTON
SANYO
018,
050,
102,
143,
201,
320,
379,
020,
056,
107,
189,
206,
325,
391,
041,
063,
117,
195,
209,
331,
408,
SAVE
049, 063
SBR
063, 112, 157, 158,
192, 313
SCHAUB LORENZ
090, 104, 136, 139,
153, 159, 162, 171,
198, 307, 416, 433
SCHNEIDER
031,
065,
104,
139,
160,
188,
040,
069,
107,
148,
168,
195,
050,
079,
112,
156,
172,
225,
063,
095,
114,
158,
182,
242,
023,
066,
244,
248,
A.1 TV codes list
SILVER
018, 042, 049, 063,
076, 172
SINGER
045, 047, 049, 063,
065, 104, 195, 324,
369, 413, 425
SINUDYNE
SKANTIC
004, 031,
063, 065,
107, 134,
172, 210,
314, 324,
367, 416
045,
094,
139,
216,
357,
051,
104,
150,
236,
366,
307, 418
STERN
036, 040, 063, 071,
079, 095, 107, 110,
171, 236, 242, 243,
305, 307, 323, 338
STRATO
049, 063, 076, 195
SUNKAI
049, 063, 094, 123,
134, 179, 191, 232,
314, 367
SUNSTAR
049, 063, 195, 225,
431
SUNWOOD
049, 063, 195
SUPERLA
379
SUPERTECH
049, 063, 123, 195,
379
SKY
049, 063
SOGERA
113
SUPRA
195
SOLAVOX
066, 102, 107, 123,
139, 172, 307
SUSMU
218
SUTRON
195
SONITRON
209, 379, 421
SWISSLINE
413
SONNECLAIR
049, 063
SYDNEY
379
SYTONG
425
SONOKO
006, 050, 063, 076,
195, 379
SONOLOR
012, 107, 139, 159,
172, 209, 357, 425
SONTEC
049, 063, 094, 421
SONY
012, 018, 028, 045,
131, 143, 204, 208,
211, 331, 357, 358,
370
SOUND & VISION
031, 045, 123
SOUND WAVE
049, 113, 163
SOUNDESIGN
042
SPECTRA
195
SSANGYONG
195
T
TACTUS
106
TANDBERG
065, 074, 078, 172,
182, 210, 213, 304
TANDY
050, 096, 102, 123,
190, 307, 379, 413
TASHIKO
018, 050, 107, 143,
177, 192, 201, 379,
419
TATUNG
049, 050, 063, 102,
106, 111, 120, 131,
200, 253, 331, 379
TEAC
049, 063, 076, 195,
380, 416, 426
TEC
040, 050, 064, 168,
195, 213, 218, 242,
243, 379, 413
STANDARD
049, 050, 063, 113,
123, 195, 379
STARLIGHT
049, 063, 076, 107,
195
TECH LINE
049, 063, 195
TECHICA
123
006, 031, 123
TECHNEMA
113
STENWAY
123
A
124
Universal Remote Control
TECHNICS
099, 315
TEDELEX
379
TEIRON
195
TEKNIKA
042, 327
TELEAVIA
029, 034, 074, 182,
186, 415, 424
TELECOR
049, 063, 107, 123,
242, 379, 423
TELEFUNKEN
032, 049, 063, 064,
074, 082, 182, 186,
187, 218, 392, 424,
436
TELEFUSION
049, 063
TELEGAZI
049, 063, 076, 107,
123, 242
TELEMEISTER
049, 063, 113
TELESONIC
049, 063
THOMSON
008,
029,
064,
174,
230,
333,
436
010,
034,
074,
182,
234,
334,
017,
049,
134,
186,
304,
415,
024,
063,
147,
218,
309,
424,
THORN
049, 053, 063, 103,
106, 141, 158, 218,
222, 321, 329, 408,
409, 411, 419
THORN-FERGUSON
032, 073, 074,
080, 082, 103,
158, 306, 319,
322, 328, 329,
358, 364, 375
THRON
117
TMK
143
TOKAI
049, 063, 102, 107,
195, 213, 379
141, 379
076,
121,
321,
357,
TELESTAR
049, 063
TOKYO
TELETECH
049, 063, 195, 213,
413
TOMASHI
006, 031, 123
TOSHIBA
001, 018, 045, 128,
141, 143, 147, 205,
341, 369, 379, 406
TOWADA
045, 379, 416
TOYODA
195
TRAKTON
076
TRANS CONTINENS
044, 046, 049, 063,
075, 171, 307, 379
TELETON
018, 067, 107, 236,
242, 379, 416
TELEVIDEON
050, 075, 104, 107,
113, 148, 379
TELEVISO
425
TEMCO
094
TEMPEST
049, 063, 195
TRANSONIC
049, 063, 380
TENNESSEE
049, 063
TRANSTEC
379
TENSAI
003, 020, 050, 055,
063, 094, 113, 117,
123, 195, 225, 379,
408, 413
TRIDENT
379
TRISTAR
123, 364
TRIUMPH
004, 046, 049, 063,
128, 147, 197, 235,
339, 375
TETUNG
046
TEVION
049, 063, 195
TEXET
050, 195, 379
U
A.1 TV codes list
UHER
ULTRAVOX
049, 063, 069, 080,
090, 113, 147, 148,
163, 236, 242, 307,
392, 407, 414, 421
044, 045, 047, 049,
050, 063, 065, 104,
107, 133, 139, 324,
379, 413
UMA
305
UNIC LINE
049, 063, 165
UNITED
049, 063
UNIVERSUM
003, 004,
020, 049,
076, 094,
155, 163,
195, 202,
213, 235,
246, 320,
379, 406,
413, 416,
429, 437
VIPER
213
VISIOLA
379
VISION
049, 063, 113
VISTAR
172, 236
VOLTEC
074
125
VORTEC
063
VOXSON
049, 063, 065, 090,
163, 171, 307, 324,
407
W
012,
063,
107,
165,
206,
244,
357,
407,
421,
018,
074,
131,
172,
210,
245,
375,
408,
428,
WALTHAM
049, 063, 163, 182,
307, 379, 418
WATSON
049, 063, 107, 113,
123, 195, 244, 245,
246, 423, 431
WATT RADIO
045, 050, 068, 104,
107, 121, 139, 150,
336, 379, 416
WEGA
UNIVOX
049, 063, 107, 121,
213, 324, 409, 411
018, 049, 063, 139,
143, 324
WEGA COLOR
065, 088
UTAX
050
WEGAVOX
195
WELTBLICK
063, 113
WESTINGHOUSE
063, 094
163
WESTON
168
VESTEL
049, 063, 107, 125,
364, 379
WHARFEDALE
049, 063
WHITE
045
VEXA
063, 195
VICTOR
174
WHITE WESTINGHOUSE 049, 050, 063, 113,
213, 379
VIDEO SYSTEM
049, 063
VIDEOLOGIQUE
031, 123, 379
V
VEGAVOX
VIDEO SYSTEM
049, 063
VIDEOTECHNIC
113, 379
VIDEOTON
107, 418
VIDIKRON
045
VIDTECH
018
WINCO
426
WINDSTAR
006
WINTERNITZ
361
X
XRYPTON
Y
049, 063
A
126
Universal Remote Control
YAMISHI
006, 049, 063, 123,
379, 380
YOKAN
049, 063
YOKO
049, 050, 063, 076,
123, 195, 379, 413,
421
YORX
123
Z
ZANUSSI
036, 040, 063, 071,
079, 095, 110, 171,
236, 305, 307, 323,
338, 379
ZOPPAS
036, 040, 071, 079,
110, 171, 307
A.2 DVD codes list
A.2
127
DVD codes list
3
3 DLAB
GRUNDIG
072
A
072, 080
H
HARMAN KARDON
001, 066
HITACHI
077
AIWA
075
ALBA
087
J
AMSTRAD
085
JMB
080
A-TREND
086
JVC
006
K
B
BLUE SKY
080
BUSH
078, 079, 082, 085
C
KENWOOD
007, 034, 043, 050,
069
KISS
077
L
CINE ULTRA
082
LAWSON
083
CYBER HOME
086
LECSON
081
LENCO
082
LG(GOLDSTAR)
005, 055, 064, 070
D
DAEWOO
083
LIFETEC
076
DENON
002, 019, 022, 034,
051
LOGIX
083
DENVER
082
M
DENZEL
077
MAGNAVOX
009, 033, 056
MANHATTAN
083
MARANTZ
033, 059, 072
MATSUI
076, 080
MEDION
076, 083
MICROMEDIA
009
MICROMEGA
072
MINOWA
083
MITSUBISHI
023, 036
MONYKA
077
DIGITOR
079
DIVIDO
083
DUAL
076, 077
E
ELTA
079
ENZER
077
G
GE
003, 004
N
A
128
Universal Remote Control
NAD
010, 062
SHINCO
087
NEUFUNK
077
SM ELECTRONIC
079
SONY
015, 029, 043, 045,
067
STANDARD
076
O
ONKYO
009, 015, 048
OPTIMUS
050
ORION
080
T
ORITRON
076
TEAC
087
TECHNICS
034
TENSAI
076, 079
024, 025, 030, 034,
035, 044, 052
TEVION
076
THOMSON
003, 004, 073
PHILIPS
009, 033, 056, 072
TOKAI
077
PHONOTREND
082
TOKIWA
083
PIONEER
010, 012, 020, 038,
041, 046, 065, 071,
074
TOSHIBA
009, 010, 033, 057,
058
TV PROJECT
PROLINE
076
008
PROSCAN
003, 004, 037
PROVISION
082
P
PANASONIC
R
RAITE
077
RCA
003, 004, 018, 037
REC
034, 078
REVOY
082
ROADSTAR
078, 079, 082
S
U
UNIVERSUM
085
W
WALKVISION
087
WESDER
082
WHARFEDALE
081
Y
YAMAHA
016, 017, 030, 034,
063
YAMAKAWA
077, 084
SANSUI
080
SCAN
083
SCHNEIDER
076
Z
SEG
077, 085
ZENITH
SHARP
021, 028, 050
005, 009, 033, 055,
064, 083
A.3 Audio system codes list
A.3
129
Audio system codes list
A
FOSGATE AUDIONICS
231, 134
ADCOM
082, 092, 225, 161,
023, 148, 149
AIWA
170, 018, 104, 202,
203, 213, 211, 188
GOLDSTAR
AKAI
189
H
ANTHEM
127, 128
HARMAN KARDON
ARCAM
141, 255
231, 233, 153, 154,
118, 119
HITACHI
020
ATLANTIC TECHNOLOGY 134
AUDIO FILE
071
G
I
INTEGRA
B
008
B&K
096, 097
J
BOSE
070, 170, 224, 147,
227, 199
JVC
BOSTON ACOUSTICS
246
029
163, 191, 114, 034,
091
K
C
CARVER
CLARION
KENWOOD
006, 028, 061, 071,
201, 214, 226, 185,
022, 077, 050
026, 066, 145, 192,
182, 005, 037, 196,
252
KLH
123
026
KRELL
150, 072, 197, 222
L
D
120, 235, 236, 237,
159, 160
DELPHI
251
LEXICON
DENON
109, 215, 230, 234,
002, 121, 133
LINN
124, 206
LUXMAN
137, 139, 052, 165,
115, 004, 009
E
ELAN
057, 090
ESCIENT
229
F
FISHER
047, 214, 182
FLEXTRONICS
207
A
M
MAGNAVOX
086, 164, 152, 208
MARANTZ
006, 028, 031, 040,
063, 185, 186, 015,
056
MCINTOSH
238, 053
130
Universal Remote Control
MERIDIAN
100, 012, 013
MITSUBISHI
242, 243, 204
MONDIAL
MYRYAD
RCA
010, 048, 117, 156,
067, 055
157, 158, 042, 043,
081, 112
REALISTIC
019, 073, 075
ROTEL
074, 083, 085
030, 099
RUSSOUND
223, 239
N
NAD
S
186, 113, 038, 216,
210
NAKAMICHI
111, 244, 245, 172,
183, 054
NIRO
135
NILES
241
O
SAMSUNG
016
SANSUI
040, 048, 110, 065,
228, 063
SANYO
047, 059
SCOTT
019
SHARP
026, 094, 131, 175
SHERWOOD
024, 102, 106, 246
SONY
018, 247, 248, 166,
101, 184, 218, 025,
179, 180, 220
ONKYO
029, 017, 046, 108,
080, 209
OPTIMUS
026, 041
SOUNDESIGN
036
OUTLAW
134
SUNFIRE
142, 143, 146
P
T
PANASONIC
032, 195, 219, 177,
098, 221
TEAC
005, 019, 049, 111,
212, 217
PARASOUND
129, 130, 132, 003,
103, 105, 125, 126
TECHNICS
122, 193, 219, 178,
177, 200, 254, 007
PHILIPS
249, 250, 063
THETA DIGITAL
136
PIONEER
014, 039, 044, 069,
168, 116, 035, 078
TOSHIBA
060, 087, 033
POLKAUDIO
251
Y
PROCEED
144, 021
R
YAMAHA
026, 253, 169, 067,
173, 205, 011, 232,
089, 027, 051, 181
A.4 Additional codes list
A.4
131
Additional codes list
MEDIA PC Controls
WINBOOK
194, 190
XP Radios
DELL
194, 190
GATEWAY
194, 190
DELPHI
251
HP
194, 190
KENWOOD
252
SONY
194, 190
POLKAUDIO
251
TOSHIBA
194, 190
SOLY
220
A
132
INDEX
Index
’After next program’, 66
’After this program’, 66
16:9, 38
1st Audio Language, 35
1st Subtitle Language, 35
22 kHz, 23
2nd Audio Language, 35
2nd Subtitle Language, 35
4:3, 38
A/V Output, 36
Access Control, 43
Active, 48
Add to Fav, 51
Advanced..., 29
ALL, 30
Alphabetic, 51, 60, 73
Animation, 46
Astra, 106
AUDIO L, 18
AUDIO L/R, 14
AUDIO R, 18
Auto, 27
Battle Tank (Network), 93
Battle Tank (Single), 88
Battle Tank(Single), 89
Brightness in Operation Mode, 46
Brightness in Standby Mode, 47
Button, 5
C band, 22
CAM, 8
CAS Only, 40
CAS only, 30
CAS–FTA, 51, 61
Censorship, 42
Center, 38
Center extract, 39
Change PIN Code, 43
CI, 8
COAXIAL, 19
Common Interface, 8
Common Interface, 9
Connection Type, 23, 97, 98
Cover, 48
Cut, 79
Date, 69
Daylight Saving Time, 41
Default, 51, 60
Default PIP Size, 47
Delete, 51, 60
Descramble Mode, 45
Descramble Multiple Services, 9
Descramble multiple services, 58
DHCP, 97
DiSEqC, 23
DiSEqC 1.0, 24
DiSEqC 1.1, 24
DiSEqC Command Mode, 25
Display Format, 38, 39
Dolby Digital, 39
Duration, 66, 69
INDEX
DVB, 1
DVB-S2 8PSK, 28, 29, 31
DVB-S2 QPSK, 28, 29, 31
Edit Favorite List, 61
Edit Service List, 59
Electronic Programme Guide, 55
ENERGY, 92
eSATA, 14
Every Day, 68
Every Weekday, 69
Every Weekend, 68
Export System Data, 33
Factory Setting, 32
Fav–NoFav, 51, 61
FEC, 28, 29, 31
File Management, 99
File Name, 69
Flickr, 85, 86
Format Hard Disk, 80
Frequency, 25, 26, 28, 29
Front Display, 46
FTA + CAS, 30
FTA only, 30
FTA–CAS, 51, 60
FTA/Scrambled, 30
FTP Server, 100
Full, 38
Gateway, 98
GMT, 40
GMT Collection, 40
Goto, 25
Goto the position, 26
Hard of hearing, 35
HD Output, 36
HDMI, 14, 17
high definition, 36
Home Transponder, 47
Import System Data, 33
Info Box Display Time, 45
Info Box Position, 45
information box, 53
Instant Recording Duration, 44
IP Address, 98
IP Setting, 97, 98
Jump Time Interval, 45
Ku band, 22
keyboard, 63
LAN, 94
LAN, 14
Language, 34
Letter Box, 39
LNB, 22
LNB 1 IN, 13, 15, 22, 23
LNB 1 OUT, 13, 15, 16, 23
LNB 2 IN, 13, 15, 16, 23
LNB 2 OUT, 13, 15, 16
LNB Frequency, 23
LNB Power, 23
LNB Setting, 22
Local Time, 40, 41
Lock, 51, 60, 73
Locked, 73
Loop Through, 23
Main Display Scrolling, 46
Manual..., 28
Media Player, 82
MediaHighway, 47
MediaHighway EPG, 47
Menu Language, 34
Mini A, 24
Mode, 40, 41, 68, 69
Modulation, 28, 29, 31
mono, 39
Mosaic, 48
Motor Control, 25
Motorized DiSEqC 1.2, 24
Motorized DiSEqC 1.3, 26
MOVE, 92
Move, 26, 48, 60
Movement, 25
MP3 Player, 81
133
134
INDEX
multifeed, 55
My Latitude, 26
My Longitude, 26
Network Firmware Upgrade, 105
Network Search, 27, 28
NEW, 61
No block, 42
Normal, 40
normal-screen television, 38
ON/OFF, 14
Once, 46
One Time, 68
OPTICAL, 19
OSD, 45
OSD Transparency, 45
OTA Firmwrae Upgrade, 106
Other, 23
Others, 47, 48
Overlap, 48
Parental Control, 42
Passive, 48
Password, 98, 100
Photo Album, 83
picture-in-picture, 57
PID, 29
Pilot, 28, 29, 31
PIN, 42
Playback, 44
Polarization, 28, 29
port forwarding, 96
POWER, 92
Primary DNS, 98
Program Guide, 55
progress bar, 70
Provider, 51, 61
Radio, 68
radio services list, 60
Record, 68
Recorded Program, 67, 72, 74, 77
recorded programme list, 72
Recording, 43
Recording Drive, 43
Recover System Data, 33
Rename, 51, 60, 73
Reservation, 68
Reset Service List, 33
S/PDIF, 39
S/PDIF, 19
S/PDIF COAXIAL, 13
S/PDIF OPTICAL, 13
SAT Name Edit, 31
SAT/TP Edit, 31
Satellite, 40, 50, 51, 60, 68
Satellite Angle, 26
satellite list, 22
Satellite Name, 22, 23, 25–29, 31, 47
Save, 79
SCART Output, 37
Search Mode, 27–29
Searching, 27
Secondary DNS, 98
Separated, 23
Service, 68
Services Copy, 30
services list, 49
Show Provider, 51
Size, 73
Slideshow Effect, 47
Slideshow Time Interval, 47
SMATV, 27
SMATV..., 29
Sort, 60
Sorting, 51, 73
Sound Mode, 39
specifications, 12, 14
Standby Mode, 4, 48
Start, 106
Start firmware upgrade, 105
Start Search, 30
Start Time, 69
Starting Position, 44
stereo, 39
Store, 25
Store System Data, 33
Sub Display Content, 46
INDEX
Subnet Mask, 98
subtitle, 54
Symbol Rate, 28, 29
System ID, 103
System Status, 103
teletext, 54
television services list, 60
Text Scroll, 46
Time, 40, 43, 73
Time Format, 41
time format, 41
Time Offset, 40
Time Padding of Timer Recording, 44
Time Shift Storage, 44
Time Shifting, 44, 56, 66
timer list, 68
Timer Recording Duration, 44
Total block, 42
Transponder, 25, 26, 40, 52, 61
transponder, 1
Trick Mode Level, 45
Tuner, 51
Tuner 1, 22
Tuner 1 to Tuner 2, 30
Tuner 2, 22
Tuner 2 to Tuner 1, 30
Tuner Select, 22, 25, 26, 47, 68
TV, 13, 17, 37, 68
TV Aspect Ratio, 38
Type, 68
USALS, 25
USALS Setting, 26
USB, 14, 64, 104
USB Firmware Upgrade, 104
User, 25
User ID, 98, 100
User Info, 98, 100, 101
User Select, 40
VCR, 13, 19
VCR Scart Type, 37
VIDEO, 14, 16, 18, 37
Video Format, 36
Weather, 87
Web Server, 98
Weekly, 69
wide-screen television, 38
Y/Pb/Pr, 13
YouTube, 84, 85
135
Manufactured under license from Dolby Laboratories. ”Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS
and Thomson.
Correct disposal of this product
This marking shown on the product or its literature indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product or their local government office for details of where and how they
can dispose this product for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Topfield continues to improve the digital receiver which this guide explains. So some explanations and illustrations in this guide could be different from the actual digital receiver.
Copyright © 2009, Topfield Co., Ltd. All rights reserved.
http://www.i-topfield.com
English version
110T-C8AC2-701-0