Active Care Medical | Cobalt X23 | Owner`s manual | Active Care Medical Cobalt X23 Owner`s manual

GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
MEDICAL POWER WHEELCHAIR
Owner’s Manual
ATTENTION
Please read your
owner’s manual
before driving your
power wheelchair.
STREAMER Sport
888WA
~0~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
CONTENTS
INTRODUCTION
page 3
FEATURE GUIDE
page 3
OPTIONAL ACCESSORY
page 4
EMI WARNING
page 5 – 6
SAFETY INSTRUCTIONS
page 7 – 8
INDICATION LABEL LOCATION
page 9
PREPARATION FOR USE
page 10
PROGRAMMABLE CONTROLLER
page 10
ADJUSTMENT PROCEDURES
page 11 – 12
OPERATION INSTRUCTIONS
page 13 – 14
DISASSEMBLY & ASSEMBLY INSTRUCTIONS
page 15 – 16
BATTERIES & BATTERY CHARGING
page 17 – 20
TROUBLE SHOOTING
page 21 – 22
SPECIFICATION
page 23
DISCLAIMER
page 24
~2~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
INTRODUCTION
Congratulations on receiving the STREAMER SPORT Powerchair. This Powerchair
is the ultimate combination of style and comfort. The short wheelbase allows easy
maneuverability within the smallest spaces both indoors and outdoors. The rear
drive wheels and electromagnetic brakes provide a safe and comfortable ride.
This manual contains important information regarding the safe use of the
Powerchair. Please read it carefully before using the Powerchair and make sure
you understand all the instructions.
Warning! Please make sure that you are physically fit to operate this unit. Consult
your dealer/doctor for advice.
FEATURE GUIDE
STREAMER SPORT (888WA)
(1)
(1)
Headrest (adjustable with selected
(2)
height)
(2)
Backrest
(3)
Joystick Controller
(4)
Charging Port
(5)
Rear Drive Wheel(10”)
(6)
Front Castor (6”)
(7)
Armrest (adjustable with selected
(8)
(3)
(7)
(4)
width, angle and height)
(8)
Captain Seat Assembly
(9)
Seat Supporting Post
(9)
(10)
(10) Chassis Shroud
(11) Footrest
(12) Option (refer to page 4)
(6)
(11)
Fig. 1
~3~
(5)
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
OPTIONAL ACCESSORY
Item
Accessory Part
Example
Adjustable
Height
Footrest
Adaptor
Elevating Leg
Rest (6-hole
adjustable as
standard. 10hole
adjustable with
60mm
extension is
optional.)
Swing-Away
Joystick Mount
Bracket
Remark: For other available accessories if required, please consult your authorized
provider.
~4~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
EMI WARNING
ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE SOURCES
Medical Power Wheelchairs (Hereinafter referred to as “Powerchair”) may be
susceptible to electromagnetic interference (EMI), which is a kind of
interfering electromagnetic energy (EM) emitted from sources such as radio
stations, TV stations, amateur radio (HAM) transmitters, two-way radio, and cellular
phones. The interference (from radio wave sources) can cause the Powerchair to
release its brakes, move by itself, or move in unintended directions. This can also
permanently damage the Powerchair’s control system.
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held portable transceivers (transmitters-receivers) with the antenna
mounted directly on the transmitting unit. Examples include: citizens band (CB)
radios, “walkie talkie”, security, fire and police transceivers, cellular
telephones, and other personal communication devices.
NOTE! Some cellular telephones and similar devices transmit signals
while they are ON, even when not being used.
2. Medium-Range mobile transceivers, such as those used in police cars, fire
trucks, ambulances, and taxis. These usually have the antenna mounted on
the outside of the vehicle.
3. Long-range transmitters and transceivers, such as commercial broadcast
transmitters (radio and TV broadcast antenna towers) and amateur (HAM)
radios.
NOTE! Other types of hand-held devices, such as cordless phones,
laptop computers, AM/FM radios, TV sets, CD players, and cassette
players, and small appliances, such as electric shavers and hair dryers, so
far as we know, are not likely to cause problems to the Powerchair.
~5~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
EMI WARNING
POWERCHAIR ELECTROMAGNETIC INTERFERENCE (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the
transmitting antenna (source), the EM fields from hand-held radio sources
(transceivers) are of special concern. It is possible to unintentionally bring high
levels of EM energy very close to the Powerchair’s control system while using
these devices. This can affect Powerchair movement and braking. Therefore, the
warnings listed below are recommended to prevent possible interference
with the control system of the Powerchair.
WARNINGS
1. Do not operate hand-held transceivers (transmitters-receivers), such as citizens
band (CB) radios, or turn ON personal communication devices, such as cellular
phones, while the Powerchair is turned ON.
2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
close contact.
3. If unintended movement or brake release occurs, turn the Powerchair OFF
as soon as it is safe.
4. Be aware that adding accessories or components, or modifying the Powerchair,
may make it more susceptible to EMI.
NOTE! There is no easy way to evaluate the overall immunity of the
Powerchair.
5. Report all incidents of unintended movement or braking to the P o w e r c h a i r
provider, and note whether there are sources of EMI nearby.
~6~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
SAFETY INSTRUCTIONS
Please use your Powerchair often and let it expand your horizons. The more
mobility your Powerchair brings, the happier you will be! But, with all things,
observing a few rules will ensure safe maneuvering. So please…
(1) Do not drive the Powerchair without reading this instruction manual.
(2) Do not use the joystick in an erratic manner when going up or down an incline.
(3) Do not carry passengers or exceed the maximum user weight (Table 2).
(4) Do not turn off the joystick controller by switching the On / Off Button
when moving at speed. This will bring the electromagnetic brakes on
imme diate ly a nd co uld cau se dam age t o t he joyst ick con tro lle r.
(5) Do not drive over uneven or soft terrain.
(6) Do not mount or dismount the Powerchair unless the electromagnetic
brakes are engaged and the joystick controller is off.
(7) Do not operate the Powerchair if the unit is in freewheel mode.
(8) Do not use on the road, except when crossing between sidewalks.
(9) Do not sit on the Powerchair when in a vehicle, but transfer to a vehicle seat.
(10) Do not exceed any grade over 8 degrees (14%).
(11) Always stop fully before changing forward or reverse direction.
(12) Always engage a slow speed when going down gradients (move the joystick
slowly towards center position to reduce the speed).
(13) Always approach and climb over curbs at slow speed.
(14) Always use the safety belt.
(15) Always keep feet on the footrest while driving.
(16) Always make sure the batteries are fully charged before setting out on a journey.
(17) Always make sure the Allen bolt and the red tightening levers are tightened before
driving the Powerchair.
(18) Always charge the Powerchair in a well ventilated area.
~7~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
SAFETY INSTRUCTIONS
(19) Whenever a center bolt of the wheel assembly has been loosened, please
replace with a specified new bolt from authorized providers and secure with a
torque of 240 ± 5 kg-cm together with Loc-tite 271 adhesive (or equivalent).
(20) When proceeding up any incline, please move the seat to the most forward
position or if you have the deluxe seat, make sure that it is in the 90 degree
(upright) position.
(21) Do not adjust the programmer or modify the controller and cables without prior
written approval from the manufacturer. Otherwise injury and/or damage to the
scooter or surrounding property may occur.
(22) Do not modify any parts on the unit without manufacturer’s written approval, or
your warranty will be voided and you will be responsible for the modification.
(23) Charge the batteries before using and charge batteries daily after use.
(24) Battery cables must be securely fastened onto battery terminals by the
authorized dealer before using the unit. Batteries must be tied down correctly
and securely.
(25) Use caution and reduce speed when turning.
(26) Avoid using the powerchair in wet conditions.
(27) Always make sure the seat post tightening levers have been tightened before
driving the powerchair.
(28) Do not use the powerchair as a seat in any vehicle.
Remember! Give consideration to pedestrians whenever using the
Powerchair. You are a motorized pedestrian and must observe all rules and
regulations of other pedestrians wherever possible.
~8~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
INDICATION LABEL LOCATION
To ensure your safety and protect the Powerchair from damage, please read the
safety instructions in this manual and familiarize yourself with the labels listed
below.
Labels on Chassis Shroud of STREAMER SPORT (888WA)
Battery Wiring Diagram
Drive
Mode
Drive
Mode
(Engaged)
(Engaged)
(Disengaged)
(Disengaged)
Free-wheel
Mode
Free-wheel
Mode
Caution: Before unit is driven, make sure the Brake Levers
are in the Engaged position (at the Drive Mode)
Fig. 2
~9~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
PREPARATION FOR USE
The Powerchair has many features designed to give the user maximum comfort.
Adjustments can be made to the following parts of the Powerchair:
(1) Footrest angle can be adjusted from 8°~22°.
(2) Armrests can be set at different angles.
(3) Arms can be adjusted in height.
(4) Arms can be adjusted in width.
(5) Joystick controller can be fitted for either right or left hand use (no tools
required).
(6) Seat supporting posts with retaining pins can be adjusted in height.
(7) Backrest angle can be slightly adjusted from 90°~102°.
Adjustments should be carried out by a provider/attendant while the user is seated
in the Powerchair with the Powerchair turned off (the seat height adjustment is made
when the user is not on the seat).
NOTE! Before using the Powerchair for the first time, be sure the batteries have
been connected. Charge the Powerchair for at least 6-8 hours prior to first time
use.
PROGRAMMABLE CONTROLLER
STREAMER SPORT (888WA) Powerchair has a programmable controller. For more
information regarding the programming parameters for the programmable
Powerchair controller please contact your provider.
~10~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
ADJUSTMENT PROCEDURES
ARM ADJUSTMENTS (Fig.3)
ANGLE
Pull up on the end of the armrests and they will flip
back up allowing easy transfer in and out of the
seat. Under the armrest, there is a bolt and lock nut
(1) that can be adjusted up or down to change the
angle of the armrest.
(3)
(1)
(2)
Fig. 3
LENGTH (Adjustable Controller Bracket)
Located under the armrest controller bracket is a hand knob (2). By turning
counter-clockwise to release, the controller bracket can be extended and reset in
position by re-tightening the hand knob.
HEIGHT
The vertical square tube connected with the armrest can be reset to the desired
position by re-tightening the hand knob (3) for armrest height adjustment.
WIDTH
Beneath the rear of the seat there are two hand knobs, one on each side. Release
the hand knob and slide each arm assembly outward. Re-tighten the hand knob
when in the desired position.
~11~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
ADJUSTMENT PROCEDURES
JOYSTICK CONVERSION (right to left or left to right)
Loosen the hand knob [Fig.3 (3)] and remove the entire armrest assembly with the
joystick attached. Place the armrest assembly on the desired side. Reset in position
by re-tightening the hand knobs to complete joystick conversion.
SEAT HEIGHT ADJUSTMENTS (Fig.4)
The seat supporting post under the seat has three height adjustment holes.
By tightening the Allen bolt and Nyloc nut in any one of the holes, three
heights can be achieved and the seat supporting post can be secured to the
power base. The seat tighten with the seat adaptor is secured to supporting
post by two hex screws & nuts. Always make sure the Allen bolt with Nyloc
nut and the hex screws with hex nuts are securely tightened before driving
the Powerchair.
The installing or setting-up method is described as Fig.4.
Hex Nut
Hex Nut
Hex Screw
Seat Supporting Post
Nyloc Nut
Hex Nut
Allen Bolt
Fig. 4
~12~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
OPERATION INSTRUCTIONS
JOYSTICK CONTROLLER (SHARK 40) OVERVIEW
10
On / Off Button (1)
This button turns the joystick controller (hereinafter
referred to as SHARK 40 joystick) on and off. Do not use
this button to stop the Powerchair, except in an emergency.
Speed Decrease Button (2)
This button decreases the maximum speed.
Speed Increase Button (3)
This button increases the maximum speed.
Fig. 5
Horn Button (4)
This button operates the Powerchair’s horn.
Battery Gauge (5)
This is a 8-segment display, which indicates if the SHARK 40 joystick is switched on
and gives the state of charge of the battery.
Maximum Speed Indicator (6)
This is a 5-segment display, which indicates the
maximum speed setting selected.
Attendant Control LED (7)
When the Attendant Remote is activated, the ACU LED will light up and remain lit
until the attendant switches back to user mode.
Service Indicator LED (8)
The amber Service Indicator LED is dedicated to displaying joystick Flash Codes.
For a list of Flash Codes and what faults they indicate. Refer to Table 1 for more
details.
Joystick (9)
This controls the speed and direction of the Powerchair. Push the joystick in the
direction you want to go. The further you push it, the faster the speed will be.
Releasing the joystick will automatically engage brakes and stop the Powerchair.
~13~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
OPERATION INSTRUCTIONS
Charging Port (10) for Off-Board Charger
Only plug a Shoprider certified charger into this port. This port should not be used
as a power supply for any other electrical devices. Disregarding this will void the
warranty of the Powerchair.
GETTING READY TO DRIVE
STEP 1 Press the On / Off Button, then the joystick will turn on after the Battery
Gauge blinks for about a second.
STEP 2 Press the Speed Increase / Decrease Button to set up a suitable level that
you can maneuver the Powerchair easily.
NOTE! The Powerchair will not move and the Battery Gauge will blink if you
push the joystick before or right after you turn the joystick on. To restore the
normal operating status, you have to release the joystick immediately back
to its center position. If you do not release the joystick within five seconds,
the Battery Gauge will flash rapidly. The Powerchair must be powered off and
then turned back on again.
STEP 3 Push the joystick to control the speed and direction of the Powerchair.
NOTE! Choose an area with plenty of space to ride the Powerchair. Select the
low level of the maximum speed setting until you are familiar with the
controls. In a short time you will be in total control and can then increase the
speed in steps.
STEP 4 Release the joystick whenever you want to stop the Powerchair.
ENGAGED / DISENGAGED MODE
In the event of a fault or battery failure, the electromagnetic brakes can be
disengaged allowing the Powerchair to be pushed. The levers should be switched to
the freewheel position according to the indication labels of Fig.2 to set the
Powerchair to the Engaged / Disengaged Mode.
NOTE! Do not use or sit on the Powerchair when either of the brakes is
disengaged, or the SHARK 40 joystick will not operate normally.
~14~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
DISASSEMBLY & ASSEMBLY INSTRUCTIONS
(2)
(1)
(3)
(5)
(4)
Fig. 6
COMPONENTS FOR STREAMER SPORT (888WA)
(1) Captain seat assembly with arm assembly.
(2) Chassis shroud.
(3) Chassis assembly.
(4) Batteries.
(5) Charger (Off-Board)
~15~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
DISASSEMBLY & ASSEMBLY INSTRUCTIONS
DISASSEMBLY PROCEDURES
WARNING! We advise caution when disassembling and lifting items. You
must ensure that the person undertaking these actions is able to handle the
weight.
STEP 1 Ensure the area where the Powerchair is to be dismantled is spacious.
STEP 2 Disconnect the plug of the SHARK 40 joystick cable.
STEP 3 Unclip two cable ties bound onto the armrest to loosen joystick cable if it’s
one piece instead of 2.
STEP 4 The arm assembly can be removed to make the seat assembly lighter to
lift. Under the rear of the seat assembly there are two hand knobs.
Release these by turning in a counter-clockwise direction and slide out
the arm assembly from each side.
STEP 5 The seat assembly should be folded down for easier lifting.
STEP 6 Loosen the nuts and then hex screws on seat post adaptor.
STEP 7 Lift the seat assembly free of the chassis assembly.
STEP 8 Loosen the nut and then hex screw on seat post. Loosen and remove
the seat height Allen bolt and Nyloc nut. Remove the chassis shroud
by simply lifting up. You will find the shroud is attached by Velcro
tapes on the chassis.
STEP 9 Unclip a cable tie bound onto the seat post receiver of the chassis
and then loosen the fastening strap on batteries. Unclip the battery
plugs (red and black). The batteries can now, with the help of carrying
straps provided, be lifted from chassis.
CAUTION! Care must be taken to slide the plug through the chassis shroud.
To reassemble the Powerchair, reverse the procedures described above.
Plug
Plug
OR
~16~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
BATTERIES & BATTERY CHARGING
BATTERIES
The Powerchair is supplied with 2 x 26 Ah sealed lead acid, maintenance free
batteries. These are located under the seat in the center of the Powerchair. For easy
handling, Velcro or plastic carrying straps may be provided to assist in installation or
removal of the batteries. The duration of the batteries can be affected by
temperature, terrain and weight of the user. The Battery Gauge is a guide on the
remaining charge in the batteries.
The active user will need to charge the batteries after using approximately more
than 30% of battery capacity. As an inactive user, only using from once a week to
every other day, the recharge point would be at 50% of discharge.
The Battery Gauge is used to indicate power on and
provides an estimate of the remaining battery
capacity.
Any green LEDs lit indicate will charged batteries.
If only amber and red LEDs are lit, the batteries are
moderately charged. Recharge before undertaking a
long trip.
If only red LEDs are lit, the batteries are running out
of charge. Recharge as soon as possible
Batteries should be kept fully charged at all times. They must not be left in a
discharged state if not using the unit for some time. The batteries should be
checked once a month and recharged as needed.
Warning!
‧ Batteries contain acid and can explode. Always wear eye protection when
working near batteries.
‧ Always keep battery terminals and clamps clean and free of corrosion.
‧ Never alter battery wiring or battery box.
‧ Never allow tools to make contact across terminals.
‧ Never use batteries or clamps with wing nut terminals, or clamps that exceed
terminal post height.
‧ Do not smoke or use open flames when battery box lid is open.
‧ Only deep cycle, sealed case construction batteries should be used in this
device.
~17~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
BATTERIES & BATTERY CHARGING
The following table indicates what the gauge will display for any given state.
Display
Description
All LEDs OFF
This means
Power is OFF
All LEDs ON
steady
Power is ON
Left RED LED is Battery charge is
flashing
low
Right to left
“chase”
Left to right
“chase”
alternating with
steady display
Alll LEDs
flashing slowly
2 Flashing
Amber LEDs
Notes
Less LEDs imply a
reduced battery
charge.
The batteries should
be charged as soon as
possible
SHARK joystick is
To unlock SHARK
being brought out of joystick, press the Horn
Lock mode
button twice within 10
seconds.
SHARK joystick is
The steady LEDs
in programming,
indicate the current
inhibit and/or
state of battery charge.
charging mode
SHARK joystick has
detected an Out Of
Neutral At Power
Up (OONAPU)
condition
A communications
fault exists between
the power module
and remote
~18~
Release the joystick
back to neutral.
Check the power
module for a fault, the
cable for damage, and
that the battery is
sufficiently charged.
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
BATTERIES & BATTERY CHARGING
BATTERY CHARGING (UNITS EQUIPPED WITH OFF-BOARD CHARGER)
Familiarize yourself with the safety information below prior to using the battery
charger.
SAFETY INFORMATION
1. Read the battery charger instructions in this manual and in the manual
supplied with the charger prior to charging the batteries.
2. Do not remove the grounding prong from the plug. Removal of the grounding
prong could result in an electrical hazard.
3. Only plug the charger into a 3-pronged electrical outlet, or an approved
3-pronged adapter for use with a 2 pronged electrical outlet.
4. Make sure that the wall outlet being used is not controlled by a wall switch
that can be easily turned off.
5. Do not use an extension cord to plug in the charger.
6. Do not leave the charger plugged into the charger port if the charger is not
charging the unit.
7. Use only the off-board charger supplied with this unit. Never use an
automotive type battery charger. Contact your supplier if a replacement
off-board charger is needed.
8. Inspect the battery charger, wiring and connections for damage prior to each
use.
9. Do not open the battery charger case.
10. The battery charger is supplied with cooling slots. Do not insert objects
through the slots.
11. Make sure that the charger is not in contact with inflammable materials at any
time.
12. The off-board charger is for indoor use only.
13. Explosive gases may be generated while charging the batteries. Keep the
power chair and battery charger away from sources of ignition such as flames
or sparks and provide adequate ventilation when charging the batteries.
14. Do not allow children to play near the power chair while the batteries are
charging. It is also recommended that the batteries not be charged while the
power chair is occupied.
~19~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
BATTERIES & BATTERY CHARGING
CHARGING INSTRUCTIONS
1. Connect the charger to the charging port at the front of the SHARK 40
joystick (item 8 in Fig.5)
2. Plug the charger into the wall outlet.
3. The charging process will start automatically.
CHARGER INDICATION LIGHTS
Blinking Green – Power on at stand-by mode,
Steady Orange – Battery charging,
Steady Green – Charging complete.
Please refer to the LED indicator description based on charging status of the charger.
BATTERY INFORMATION
1. Make sure to use two batteries of the exact same chemistry, amp hours, and
capacity.
2. Fully recharge new batteries prior to initial use.
3. It is recommended that the batteries be charged for 8 to 14 hours after daily
use.
4. If the power chair is used infrequently (Once a week or less) the batteries will
need to be charged once a week for 12 to 14 hours.
5. Do not charge the batteries for more than 24 hours at a charging cycle.
6. Batteries that go below a minimum voltage due to not being charged will be
unable to be re-charged.
7. If you do not plan on using your power chair for an extended period it is
recommended that you fully charge the batteries and then disconnect the
battery harness prior to storage. Store the power chair in a warm dry
environment. Never store the batteries where extreme temperatures are
possible. Never attempt to charge a frozen battery. A cold or frozen battery
should be warmed for several days prior to charging.
~20~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
TROUBLE SHOOTING
The Self-Help Guide (Table 1) is intended to assist in the location of a
fault that may occur in a certain part of the Powerchair. Flash codes
indicate the nature of an abnormal condition directly from the
SHARK joystick Information Gauge. Without the use of any servicing tools, the
condition can be simply diagnosed.
If after checking out the fault from the table below and the fault is still
showing, do not use the Powerchair. Turn off the power and consult your
provider immediately.
Table 1
Flash
Description
Code
User Fault
Possible stall timeout or user error.
Release the joystick to neutral and try again.
2
Battery Fault
Check the batteries and cabling.
Try charging the batteries.
Batteries may require replacing.
3
Left Motor Fault
Check the left motor connections and cabling.
4
Right Motor Fault
Check the right motor connections and cabling.
5
Left Park Brake Fault
Check the park brake connections and cabling.
6
Right Park Brake Fault
Check the park brake connections and cabling.
7
SHARK Remote Fault
Check the SHARK Communications Cable.
Replace the Remote.
8
SHARK Power Module
Fault
Check the SHARK joystick connections and wiring.
Replace the Power Module.
9
SHARK
Communications Fault
Check for possible low battery.
Check the SHARK joystick connections and wiring.
Check for worn motor brushes.
Replace the Remote.
10
Unknown Fault
Check all connections and wiring.
Consult a service agent.
11
Incompatible Remote
Wrong type of Remote connected.
1
~21~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
TROUBLE SHOOTING
LOCK MODE: The SHARK 40 joystick can be locked to prevent unauthorized use.
The locking method is achieved through a sequence of key
presses and joystick movements, as detailed below.
To lock Powerchair controller:

While the power is ON, press and hold the Power button for 4 seconds.

This display will turn off immediately.

After 4 seconds all LED’s will flash briefly and the horn will sound a short
beep.

The Powerchair will then turn off.
To unlock the Powerchair controller:

While the SHARK joystick is locked, press the Power button to turn SHARK
joystick on.

All LED’s will flash briefly. The Battery Gauge LED’s will them perform a slow
right-to-left chase.

Press the Horn button twice before the countdown is completed
(approximately 10 seconds).

This current state-of-charge will then be displayed and SHARK joystick may
be operated normally.
SLEEP MODE: After a certain amount of time with no joystick movement, the
joystick will automatically turn itself off. Sleep mode will not be
entered while programming. When Wakeup style has been set to
“Joystick and Button”, pressing ANY button ONLY will bring the
system out of sleep mode.
~22~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
SPECIFICATION
Table 2
ITEM
UNIT
888WA
Overall Length1
Inches
38”
Overall Width
Inches
22”
Overall Height
Inches
40”
Total Weight (w/ 26 Ah Batteries)
Lbs
160
Battery Weight
Lbs*pcs
17 lbs*2
Battery Capacity
12V_Ah x 2pcs
26Ah
Safe Climbing Angle
°(%)
8(14)
Suggested User Weight (on level surface)
Lbs
Max. 300
Maximum Speed3
mph
5
Range
(Per charge w/ standard 26 Ah battery)
Miles
8
Charger Type
On / Off Board
Off Board 24V, 5A
4
®
®
All specifications are subject to change without prior notice. SHOPRIDER / PIHSIANG reserves
the
rights of any changes on the unit.
1. Includes the anti-tip wheel.
2. The actual driving range varies with the factors shown below.
(1) the weight of occupant
(2) ground surface
(3) battery capacity and conditions
(4) type of charger
(5) ambient temperature
(6) Driving methods
(7) If the battery and mechanical moving parts fully broken in.
~23~
GMP
ISO9001
ISO14001
ISO13485
CERTIFIED
DISCLAIMER
Congratulations on receiving the STREAMER SPORT Powerchair.
This Powerchair is not intended to be used by individuals with physical limitations
that could prevent the user from operating the Powerchair safely. SHOPRIDER®
disclaims all responsibility for any personal injury or property damage, which may
occur as a result of improper or unsafe use of its products. Mechanical or electrical
defects will be dealt with on a contingency liability basis.
Warranty is only valid when genuine SHOPRIDER® parts are used. All
modifications on the Powerchair, unless approved and authorized by SHOPRIDER®
will automatically invalidate the warranties. Standard warranty does not extend to
consumable items and parties other than the original user.
The preceding guidelines are intended to assist you in the safe operation of this
Powerchair. If you should have any questions about the correct operation of the
Powerchair, please contact your authorized SHOPRIDER® provider.
.
Provider Stamp
Serial No.:
SHOPRIDER MOBILITY PRODUCTS, INC
21184 S. FIGUEROA ST
CARSON, CA 90745
800-743-0772
P/N: 300904-57-A6C
© Copyright PIHSIANG MACHINERY MFG. CO., LTD. 2003. All rights Reserved. SHOPRIDER
MACHINERY MFG. CO., LTD.
~24~
®
/ PIHSIANG
®
are registered trademarks of PIHSIANG
Download PDF

advertising