MULTIQUIP DCA-85SSJU Specifications

MULTIQUIP DCA-85SSJU Specifications
PARTS AND OPERATION MANUAL
MQ POWER
DCA-85SSJU
TM
WHISPERWATT
GENERATOR
© COPYRIGHT 2001, MULTIQUIP INC.
(STANDARD)
PARTS LIST No. M2872300104
Revision #2 (12/21/01)
MULTIQUIP INC..
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:[email protected] • www:multiquip.com
PAGE 2 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 3
TABLE OF CONTENTS
Here's How To Get Help ............................................... 3
Parts Ordering Procedures .......................................... 5
Rules for Safe Operation .......................................... 6-9
Towing Safety Precaution .......................................... 10
Trailer Safety Guidelines ....................................... 11-17
Trailer Wiring Diagram ................................................ 18
Electrical Brake Troubleshooting ................................ 19
Hydraulic Brake Troubleshooting ................................ 20
Operation and Safety Decals ................................ 21-22
DCA-85SSJU Specifications ..................................... 23
General Information ................................................... 24
Major Components .................................................... 25
Dimensions ................................................................ 26
Control Panel Descriptions ................................... 28-29
Engine Operating Panel Descriptions ................... 30-31
Output Terminal Panel Overview ........................... 32-39
Installation ............................................................ 40-41
Pre Setup ............................................................. 42-45
Load Application ........................................................ 46
Generator Start-up Procedure .............................. 47-49
Generator Start-up Procedure, Auto .......................... 50
Generator Shut-Down Procedure ............................... 51
Maintenance ......................................................... 52-53
Generator Wiring Diagram .......................................... 54
Engine Wiring Diagram .............................................. 55
Engine Troubleshooting ......................................... 56-57
Generator/Engine Troubleshooting ............................. 58
Engine Controller Troubleshooting .............................. 59
Explanation of Code in Remarks Column .................. 60
Suggested Spare Parts ............................................. 61
MQPower DCA 85SSJU
AC Generator
Generator Assembly ............................................. 62-63
Control Box Assembly ........................................... 64-67
Engine & Radiator Assembly ................................. 68-71
Engine Operating Panel Assembly ........................ 72-73
Output Terminal Assembly ..................................... 74-75
Battery Assembly .................................................. 76-77
Muffler Assembly .................................................. 78-79
Fuel Tank Assembly ............................................ 80-81
Enclosure Assembly ............................................. 82-85
Rubber Seal Assembly .......................................... 86-87
Name Plate And Decals ........................................ 88-89
Terms and Condition of Sale — Parts ....................... 90
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
PARTS ORDERING PROCEDURES
■
■
■
■
■
■
■
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
•
•
•
•
UPS Ground
UPS Second Day or Third Day*
UPS Next Day*
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
•
Airborne Express*
Truck or parcel post
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
1-9 items
Additional Discount
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
■ UPS Ground Service at no charge for freight
■ PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
*DISCOUNTS ARE SUBJECT TO CHANGE*
ount
c
s
i
D
Fax
Extra
c USA
i
t
s
e
m
for Do
Only
s
r
e
l
a
De
UPS l
Specia
xed
For fa
only
orders
Now! Direct TOLL-FREE access
to our Parts Department!
Toll-free nationwide:
800-421-1244
Toll-free FAX:
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 5
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This equipment
is for industrial use only.
The following safety guidelines should always be used when
operating the DCA-85SSJU portable generator:
GENERAL SAFETY
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by
persons under 18 years of age.
■ NEVER operate this equipment without proper
protective clothing, shatterproof glasses,
steel-toed boots and other protective devices
required by the job.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
■ High Temperatures – Allow the engine to cool before
adding fuel or performing service and maintenance
functions. Contact with hot components can cause serious
burns.
■ The engine of this generator requires an adequate free
flow of cooling air. Never operate the generator in any
enclosed or narrow area where free flow of the air is
restricted. If the air flow is restricted it will cause serious
damage to the generator or engine and may cause injury
to people. The generator engine gives off DEADLY carbon
monoxide gas.
CAUTION
CAUTION:
Always refuel in a well-ventilated area,
away from sparks and open flames.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
■
Always use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
NEVER operate the generator in an
explosive atmosphere or near combustible materials. An
explosion or fire could result causing severe bodily harm
or even death.
■ Always check the machine for loosened threads or bolts
before starting.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
PAGE 6 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
RULES FOR SAFE OPERATION
CAUTION
CAUTION:
CAUTION
CAUTION:
DO NOT touch or open any of the below
mentioned components while the
generator is running. Always allow
sufficient time for the engine and generator
to cool before performing maintenance.
NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when
contact with the output terminals.
CAUTION
CAUTION:
■ Backfeed to a utility system can cause electrocution
and.or property damage. Do not connect to any
building's electrical system except through an approved
device or after building main switch is opened.
Radiator
1. Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, causing severe scalding to
any persons in the general area of the generator.
2. Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant to gush
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
3. Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
CAUTION
CAUTION:
Never use damaged or worn cables when
connecting power tools or equipment to the
generator. Make sure power connecting
cables are securely connected to the
generator’s output terminals, insufficient
tightening of the terminal connections may
cause damage to the generator and
electrical shock.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 7
RULES FOR SAFE OPERATION
NEVER Run engine without air filter. Severe engine
damage may occur.
Battery
CAUTION
CAUTION:
Never over fill the battery with water
above the upper limit.
The battery contains acids that can cause injury to the eyes
and skin. To avoid eye irritation, always wear safety glasses.
Use well insulated gloves when picking up the battery. Use
the following guidelines when handling the battery:
Always service air cleaner frequently to prevent carburetor
malfunction.
Always disconnect the battery before performing service
on the generator.
Always be sure the operator is familiar with proper safety
precaution s and operations techniques before using
generator.
Always store equipment properly when not in use.
Equipment should be stored in a clean, dry location out of
the reach of children.
DO NOT leave the generator running in the manual mode
unattended.
DO NOT allow unauthorized people to operate this
equipment.
1. DO NOT drop the battery. There is the possibility of risk
that the battery may explode.
Always read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
Refer to the John Deere Engine Owner's Manual for
engine technical questions or information.
3. Always keep the battery charged. If the battery is not
charged a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or hospital,
and seek medical attention.
Loading and Unloading (Crane)
Before lifting, make sure the generator's lifting hook is
secure and that there is no apparent damage to the
generator itself (loose screws, nuts and bolts). If any
part is loose or damaged, please take corrective action
before lifting.
Always drain fuel prior to lifting.
Always make sure crane or lifting device has been
properly secured to the hook of guard frame on generator.
NEVER lift the machine while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient
strength.
When lifting the generator, always use the balanced
center-point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath
the machine while lifting.
When loading the generator on a truck, be sure to use
the front and back frame bars as a means to secure the
generator during transport.
PAGE 8 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
RULES FOR SAFE OPERATION
Transporting
Always shutdown engine before transporting.
Tighten fuel tank cap securely.
Drain fuel when transporting generator over long distances
or bad roads.
Always tie-down the generator during transportation by
securing the generator.
If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. See page 10 for basic towing procedures.
Emergencies
Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
Maintenance Safety
NEVER lubricate components or attempt service on a
running machine.
Always allow the machine a proper amount of time to
cool before servicing.
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always
replace broken parts.
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, coolant,
fuel, and fuel filters.
DO NOT use plastic containers to dispose of hazardous
waste.
DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 9
DCA-85SSJU — TOWING RULES FOR SAFE OPERATION
Towing Safety Precautions
CAUTION :
Check with your county or state safety
towing regulations department before towing
your generator.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
(Figure 1) that supports the generator and the towing vehicle
are in good operating condition and both units are
mechanically sound.
The following list of suggestions should be used when towing
your generator:
Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains
etc.
Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.
ALWAYS make sure the trailer is equipped with a "Safety
Chain".
ALWAYS attach trailer’s safety chain to bumper of towing
vehicle.
ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
The maximum speed for highway towing is 45 MPH
unless posted otherwise. Recommended off-road towing
is not to exceed 10 MPH or less depending on type of
terrain.
Place chocked blocks underneath wheel to prevent
rolling, while parked.
Place support blocks underneath the trailer’s bumper to
prevent tipping, while parked.
Use the trailer’s hand winch to adjust the height of the
trailer, then insert locking pin to lock wheel stand in place,
while parked.
Avoid sudden stops and starts. This can cause skidding,
or jack-knifing. Smooth, gradual starts and stops will
improve gas milage.
Avoid sharp turns to prevent rolling.
.Remove wheel stand when transporting.
DO NOT transport generator with fuel in tank.
Figure 1. Generator with Trailer
PAGE 10 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — TRAILER-SAFETY GUIDELINES
CAUTION:
ALWAYS make sure the trailer is in good
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
Explanation of Chart:
This section is to provide the user with trailer service and
maintenance information. The service and maintenance
guidelines referenced in this section apply to a wide range of
trailers. Periodic inspection of the trailer will ensure safe
towing of the equipment and will prevent damage to the equipment and personal injury.
It is the purpose of this section to cover the major maintenance components of the trailer. The following trailer components will be discussed in this section:






Brakes
Tires
Lug Nut Torquing
Suspension
Electrical
Brake Troubleshooting Tables
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hydraulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, including the fuel cell (empty).
4.
Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
5. Frame Width - This measurement is from fender to
fender.
6.
Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 4 and Figure 5 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can support in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please note that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 11
DCA-85SSJU —TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FU E L
C E LL
BRAKE
SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
TRLR-10W
SDW225,
SGW250,TLW300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10
DCA10, TLG12,
DCA-15
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10XF
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-225W
WELDERS,
D A 7000S S
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
TRLR-BLW400
BLW-400
NO
ELECTRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TRLR-50X
DCA-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-50XF
DCA-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-70W
DCA-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-70X
DCA-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-70XF
DCA-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-100XF
DCA-100, 125
150 GAL
HYDRAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TRLR-85/125
DCA-85, 100,
125
145 GAL
HYDRAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-150XF
DCA-150, 180
200 GAL
HYDRAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TRLR-220XF
DCA-220
250 GAL
HYDRAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TRLR-300XF
DCA-300
250 GAL
HYDRAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-400XF
DCA-400
350 GAL
ELECTRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-600XF
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TRLR-800SX
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU —TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS SUSPENSION
ELECTRICAL
TRLR-10W
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X 2
5 LUG
3 LE A F
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-10XF
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-225W
2" B A LL C LA S S
2 ADJUSTABLE
175-13B
13X4.5"
2200#2X 2
5 LUG
Q F LE X
4 POLE FLAT
TRLR-BLW 400
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13 X 4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-50X
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-50XF
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-70W
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70X
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70XF
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-100XF
ADJUSTABLE 2-5/6
OPT 3" EYE
205-15C
BIAS (4)
14"X5.5"
3500lbs
3"
5 LUG
5 LE A F
4 WIRE LOOM
TRLR-85/125
ADJUSTABLE 2-5/6
OPT 3" EYE
ST225/75R15D
RADIAL (4)
14"x6"
(2)-6000lbs
6 LUG
7 LE A F
4 WIRE LOOM
TRLR-150XF
3" BALL EYE
750-16 E
BIAS (4)
16" X 7"
(2)-6000lbs
8 LUG
7 LE A F
4 WIRE LOOM
TRLR-220XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(4)
16" X 7"
(2)-7000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-300XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(2)-6000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-400XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(3)-7000lbs.
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-600XF
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
7 LE A F
6 WIRE LOOM
TRLR-800AR
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
AIR-RIDE
6 WIRE LOOM
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 13
DCA-85SSJU —TRAILER SAFETY GUIDELINES
Brakes
If your trailer has a braking system, the brakes should be
inspected the first 200 miles of operation. This will allow
the brake shoes and drums to seat properly. After the first
200 mile interval, inspect the brakes every 3,000 miles. If
driving over rough terrain, inspect the brakes more
frequently.
Electric Brakes
Electrically actuated brakes (Figure 2) are similar to
hydraulic brakes. The basic difference is that hydraulic
brakes are actuated by an electromagnet.
Listed below are some of the advantages that electric
brakes have over hydraulic brakes:
 Brake system can be manually adjusted to provide
the corrected braking capability for varying road and
load conditions
 Brake system can be modulated to provide more or
less braking force, thus easing the brake load on the
towing vehicle
 Brake system has very little lag time between the time
the vehicle’s brakes are actuated and the trailer’s brakes
are actuated
 Brake system can provide an independent emergency
brake system
Remember in order to properly synchronize the tow vehicle’s
braking to the trailer’s braking, can only be accomplished
by road testing. Brake lockup, grabbiness or harshness is
due to lack of synchronization between the tow vehicle
and the trailer being towed or under-adjusted brakes.
Before any brake synchronizations adjustments can be
made, the trailer brakes should be burnished-in by applying
the brakes 20-30 times with approximately a 20 m.p.h.
decrease in speed, e.g. 40 m.p.h. to 20 m.p.h. Allow ample
time for brakes to cool between application. This allows
the brake shoes to slightly be seated into the brake drum
surface.
Figure 2 displays the major electric brake components that
will require inspection and maintenance. Please inspect
these components as required.
Electric Brake Adjustment
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting
slot at the bottom brake backing plate.
4. With a screwdriver or standard adjusting tool, rotate
the star wheel of the adjuster assembly to expand the
brake shoes.
5. Adjust the brake shoes outward until the pressure of
the lining against the wheel drum makes the wheel
difficult to turn.
6. Rotate the star wheel in the opposite direction until the
wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer
to the ground.
8. Repeat steps 1 through 6 on the remaining brakes.
PAGE 14 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — TRAILER SAFETY GUIDELINES
Figure 2. Electrical Brake Components
Hydraulic/Air/Surge Brakes
Hydraulic brakes (Figure 3) should not require any special
attention with the exception of routine maintenance such
as shoe and lining replacement. These brakes can be
adjusted in the same manner as electric brakes. Brake
lines should be periodically checked for cracks, kinks, or
blockage.
Figure 3 below displays the major hydraulic/air/surge brake
components that will require inspection and maintenance.
Please inspect these components as required using steps
1 through 6 as referenced in the electric brake adjustments
section.
Figure 3. Hydraulic Brake Components
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 15
DCA-85SSJU — TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the
air pressure in
the inner tube
may cause pieces of the rim to
explode (break off) with great force
and cause serious eye or bodily
injury.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Suspension
The leaf suspension springs and associated components
(Figure 4) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
CAUTION:
NOTE
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to comply
may result in serious injury.
Figure 4. Major Suspension Components
PAGE 16 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU —TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 5. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 5. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 17
DCA-85SSJU —TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 18 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU —TRAILER-BRAKE TROUBLESHOOTING
Table 5. Electric Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes or Intermittent Brakes
Any open circuits or broken wires?
Find and correct.
Any short circuits?
Find and correct.
Faulty controller?
Test and correct.
Any loose connections?
Find and repair.
Ground wire secure?
Find and secure.
Grease or oil on magnets or linings?
Clean or replace.
Connections corroded?
Clean and correct cause
of corrosion.
Brake drums scored or grooved?
Machine or replace.
Brakes synchronized?
Correct.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Bearings of the wheel adjusted?
Adjust.
Weak Brakes or Brakes Pull to
One Side
Locking Brakes
Noisy Brakes
Dragging Brakes
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 19
DCA-85SSJU —TRAILER-BRAKE TROUBLESHOOTING
Table 6. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes
Brake line broken or kinked?
Repair or replace.
Weak Brakes or Brakes Pull to
One Side
Brake lining glazed?
Reburnish or replace.
Trailer overloaded?
Correct weight.
Brake drums scored or grooved?
Machine or replace.
Tire pressure correct?
Inflate all tires equally.
Tires unmatched on the same axle?
Match tires.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Brake lining thickness correct or in right
wrong position?
Install new shoes and
linings.
Enough brake fluid or correct fluid?
Replace rubber parts
fill with dot4 fluid.
Locking Brakes
Noisy Brakes
Dragging Brakes
PAGE 20 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — GENERATOR DECALS
The DCA -85SSJU generator is equipped with a number of safety decals. These decals are provided for operator safety
and maintenance information. The illustration below and on the preceding pages show the decals as they appear on the
machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 21
DCA-85SSJU — GENERATOR DECALS
PAGE 22 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — SPECIFICATIONS
Table 7. Specifications
Generator Specifications
Model
DCA-85SSJU
Type
Revolving field, self ventilated, open protected type synchronous generator
Armature Connection
Star with Neutral
Zig Zag
Phase
3
Single
Standby Output
88 KVA (70.4 KW)
66KW
Prime Output
82 KVA (65.6 KW)
60KW
Voltage
240V or 480V
240/120V
Frequency
60 Hz
Speed
1800 rpm
Power Factor
0.8
1
Aux. AC Power
Single Phase, 60 Hz
Voltage
120 V
Output
4.8 KW (2.4 KW x 2)
Engine Specifications
Model
JOHN DEERE 4045 TF 250
Type
4 cycle, water-cooled, direct injection, turbo-charged
No. of Cylinders
4 cylinders
Bore x Stroke
4.19 in. x 5 in. (106 mm x 127 mm)
Rated Output
102HP/1800 rpm
Displacement
274 cu. in. (4500 cc)
Starting
Electric
Coolant Capacity
6.9 gal. (26 liters)
Lube Oil Capacity
3.4 gal. (13 liters)
4.8 gal. (18.2L)/hr at full load
3.5 gal. (13.3L)/hr at 3/4 load
2.6 gal. (9.9L)/hr at 1/2 load
1.6 gal. (6.1L)/hr at 1/4 load
Fuel Consumption
Battery
12V- 120AH
Fuel
#2 Diesel Fuel
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 23
DCA-85SSJU — GENERAL INFORMATION
DCA-85SSJU FAMILIARIZATION
Open Delta Excitation System
Generator
The DCA-85SSJU generator is equipped with the state of
The MQ Power Model DCA-85SSJU is a 68 kW generator the art "Open-Delta" excitation system. The open delta
that is designed as a high quality portable (requires a trailer system consist of an electrically independent winding wound
for transport) power source for telecom sites, lighting among stationary windings of the AC output section.
facilities, power tools, submersible pumps and other There are four leads: A, B, C and D. During light loads, the
industrial and construction machinery.
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
Engine Control Panel
increase, the AVR switches and accepts power from leads
The “Engine Control Panel” is provided with the following:
A&D. The output of leads A&D increase proportionally with
 Tachometer
load. This of adding the voltages to each phase provides
 Water Temperature Gauge
better voltage response during heavy loads.
 Oil Pressure Gauge
The connections of the AVR to the AC output windings are
 Charging Ammeter Gauge
for sensing only. No power is required from these windings.
 Engine Speed Switch
 Microprocessor Engine Controller (engine controller)
The open-delta design provides virtually unlimited excitation
 Pre-Heat Button
current, offering maximum motor starting capabilities. The
 Panel Light
excitation does not have a "fixed ceiling" and responds
 Panel Light Switch
according the demands of the required load.
Microprocessor Controlled Alarm System
Generator Control Panel
The DCA-85SSJU generator is equipped with various alarms
The “Generator Control Panel” is provided with the following: and LED status indicators. These alarms and status
 Output Voltage Adjustment Knob
indicators are provided to add safety to the generator when
 Frequency Meter (Hz)
operating under normal conditions. The DCA-85SSJU
 AC Ammeter (Amps)
generator is designed to shutdown in the event of low oil,
 AC Voltmeter (Volts)
high coolant temperature, low battery and other operation
 Ammeter Change-Over Switch
conditions that may cause severe damage to the engine.
 Voltmeter Change-Over Switch
Engine
The DCA-85SSJU is powered by a 4 cycle, water cooled,
Output Terminal Panel
turbocharged JOHN DEERE Model 4045TF 250 diesel
The “Output Terminal Panel” is provided with the following: engine. This engine is designed to meet every performance
 Three 240/139V output receptacles, 50 amp
requirement for the generator. Reference Table 7, page 23
 Two 120V input receptacles, 20 amp
for engine specifications.
 3 Load Circuit Breakers 265V @65 amps
In keeping with Multiquip's policy of constantly improving
 2 Load GFCI Circuit Breakers [email protected] 20amps
its products, the specifications quoted herein are subject to
Control Box
change without prior notice.
The “Control Box” is provided with the following:
The basic controls and indicators for the DCA-85SSJU
 Main Circuit Breaker 250 amps
generator are addressed on the following pages.
 Over-Current Relay
PAGE 24 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — MAJOR COMPONENTS
Figure 6. Major Components
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 25
DCA-85SSJU — DIMENSIONS
Figure 7. Dimensions
PAGE 26 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
NOTE PAGE
Figure 3b. Dimensions
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 27
DCA-85SSJU — CONTROL PANEL
Figure 8. Control Panel
PAGE 28 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-85SSJU " Control Panel " (Figure 8).
1.
Main Circuit Breaker – This three-pole, 250 amp main
breaker is provided to protect the UVW voltage output
terminals from overload.
2.
AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
3.
Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals, or
to be switched off.
4.
Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
5.
Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz ±1 Hz .
6.
7.
AC Voltmeter – Indicates the single phase output
voltage present at the UVW terminals.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 29
DCA-85SSJU — ENGINE OPERATING PANEL
Figure 9. Engine Operating Panel
PAGE 30 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENGINE OPERATING PANEL
If the engine does not engage (start) by the
The definitions below describe the controls and functions of disengaging.
the DCA-85SSJU " Engine Operating Panel " (Figure 10). third attempt, the engine will be shutdown by the engine
1. Panel light - Normally used in dark places or at night. controller's " Over Crank Protection" mode. If the engine
When activated, panel will luminate. When the generator engages at a speed (RPM's) that is not safe, the engine
is not in use, turn the panel light switch to the ‘OFF’ controller will shutdown the engine by initializing the "Over
Speed Protection" mode.
position.
Also the engine controller will shutdown the generator in the
2. Panel light switch- When activated, will turn on control event of low oil pressure, high coolant temperature, low
panel light.
coolant level, and loss of magnetic pickup. These conditions
3. Oil Pressure Gauge – Normal operation should be about can be observed by monitoring the LED status indicators on
42~71 psi. When starting the generator the oil pressure the front of the engine controller module.
may read a bit higher, but after the engine warms up
the oil pressure should return to normal.
A. Off/Manual/Auto Switch – This switch controls the
4.
Water Temperature Gauge – During normal operation
this gauge be should read between 165oF to 203oF.
5.
Charging Ammeter Gauge – Indicates the current
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
6.
Fuel Gauge - Indicates amount of diesel fuel available.
7.
running of the generator. If this switch is left in the "OFF"
position, the generator will not run. When this switch is
set to the manual position, the generator will start
immediately.
If the generator is to be connected to a building's AC
power source via a transfer switch (isolation), place the
switch in the auto position. In this position the generator
will monitor the AC line output from the building's power
source.
Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour B. Low Oil Pressure – Indicates the engine pressure
has fallen below 15 psi. The oil pressure is detected
meter will record the number of operational hours that
using variable resistive values from the oil pressure
the generator has been in use.
sending unit. This is considered a major fault.
8. Engine Speed Switch- This handle will change the
C. High Coolant Temperature – Indicates the engine
speed of the engine from high to low.
temperature has exceeded 215°F. The engine
temperature
is detected using variable resistive values
9. Pre-Heat Button – Press hold this button
from
the
temperature
sending unit. This is considered a
until the preheat lamp is lit (ON).
major fault.
D. Overcrank Shutdown – Indicates the unit has
attempted to start a pre- programmed number of times,
10. Auto/Stop Manual Engine Controller- Has a vertical
and has failed to start. The number of cycles and duration
row of status LED's (Figure 11), that when lit, indicate that
are programmable. It is preset at 3 cycles with a 10
an engine malfunction (fault), has
second duration. This is considered a major fault.
been detected. When a fault has
E. Overspeed Shutdown – Indicates the engine is running
been detected the engine controller
at an unsafe speed. This is considered a major fault.
will evaluate the fault and all major
F. Engine Running – Indicates that engine is running at
faults will shutdown the generator.
a safe operating speed.
During cranking cycle , The
controller will attempt to crank the
engine for 10 seconds before
Figure 11. Engine
Controller
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 31
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
OUTPUT TERMINAL FAMILIARIZATION
The “Output Terminal Panel” is provided with the following:
 Three 120/240V output receptacles, 50 amp
 Two 120V receptacles, 20 amp
 3 Circuit Breakers 240V @50 amps
 2 GFCI Circuit Breakers [email protected] 20amps
Connecting Load
Loads can be connected to the generator by the UVW Lugs or
the convienience receptacles. (See Figure 13). Make sure to
read the operation manual before attempting to connect a load
to the generator.
Control Box
The “Control Box” is provided with the following:
 Main Circuit Breaker 250 amps
 Over-Current Relay
Output Terminal Panel
The Output Control Panel (See Figure 14) is located on the
right hand side (left from control panel) of the generator.
The UVW lugs are protected by a face plate cover that can
be secured in the close position by a pad lock. (See Figure
11).
FIGURE 11. Output Terminal Cover
120 Volt Recetacle
Two GFCI Duplex Nema 5-20R (120V, 20 Amp) recepacle is
provided on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
Pressing the reset button resets the receptacle after being
tripped. Pressing the "Test Button" (See Figure 12) in the
center of this receptacle will check the GFCI function. The
receptacle should be tested at least once a month.
FIGURE 13. Connecting Load
Circuit Breakers
To protect the generator from an overload, a 3-pole, 240 amp,
main circuit breaker is provided to protect the UVW output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit breakers
have also been provided to protect the load side of the
generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Maximum Output
The entire load connected to the UVW Lugs, all four slots in the
duplex receptacles, and the must not exceed 70 kW in standby
or 65 kW in prime output.
Twist Lock Dual Voltage Receptacles - To use these
receptacles, place the voltage selector switch in the single
phase 240/120 voltage position and adjust the output
voltage to 240 volts with the voltage regulator on the
Control Panel. Place the voltmeter change-over switch to
the U-W positon and the ammeter change-over switch to
the U or W to read the output.
FIGURE 12. GFCI Test Button
PAGE 32 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
FIGURE 14. Output Terminal Panel
NOTE
Legs O and Ground are
considered Bonded Grounds.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 33
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
Output Terminal Panel Available Voltages
A wide range of voltages are available to supply load to
many different applications. Voltages may be selected by
using the voltage selector switch and how you hookup
your hard wire connection to the generator. To obtain some
of the voltages listed, fine adjustment with the Voltage
Regulator on the control panel is necessarry. See the
table below (Table 8) for a list of available voltages the
generator is able to supply.
Maximum Amps
The following table show the maximum amps the entire
generator can provide. Do not exceed the maximum amps
listed. (See Table 9 below.)
Table 9. Maximum Amps
Model:
DCA85SSJU
Rated
Voltage
Maximum Amps
Single Phase
120 Volt
550 amps (4 wire)
Voltage Selector Switch
The voltage selector switch is located above the UVWO
Hard Wire Hook-up Panel. It has been provided for ease of
voltage selection.
Single Phase
240 Volt
275 amps (4 wire)
Three Phase
240 Volt
198 amps
CAUTION :
Three Phase
480 Volt
99 amps
Table 8. Voltages Available
3-Phase
208 VOLT
220 VOLT
240 VOLT
416 VOLT
440 VOLT
480 VOLT
Single Phase
120 VOLT
127 VOLT
139 VOLT
240 VOLT
254 VOLT
277 VOLT
NEVER switch Voltage Selector Switch
position while the engine is engaged.
Receptacle Use
When the UVWO terminals are providing power, the
receptacle power available decrease. Do not exceed
receptacle power available listed on Table 10.
Voltage Selector Switch Locking Button
The voltage selector switch has a locking button to protect
the generator and generator load from being switched while
the engine is running. To lock the Voltage Selector Switch,
press in the red button located on the Voltage Selector
Switch, and use a pad lock to hold it into this position.
(See figure 17, page 37)
Over Current Relay
An over current relay is connected to the circuit breaker.
In an over current situation, both the circuit breaker and
the over current relay may trip. If the circuit breaker can
not be reset, the reset button on the over current relay
must be pressed. The over current relay is located in the
control box.
Table 10. Receptacle Use
Power in Use
Receptacle
Power
Available
240/480V
3-Phase
240/120V
Single Phase
or Twist Lock
CS6369
Duplex NEMA
5-20R 120V
85
60
0
77.8
58.8
1.2
73.7
57.6
2.4
69.5
56.4
3.6
65.4
55.2
4.8
PAGE 34 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
How to read the output terminal gauge.
The gauge and knobs on the control panel DO NOT effect
the generator output . They are to help observe how
much power is being supplied produced at the UVWO
legs.
When the Voltage selector switch is in the 240/120V
position (see Figure 15), place the AC Voltmeter Changeover switch to the W-U position and the AC ammeter
Change -over Switch to the U or W position to read the
output on the selected leg.
20
40
0
75
A
FIGURE 18. AC Ammeter
Change-over Switch
(Reading the U leg on the
output terminal panel)
FIGURE 19. AC Ammeter
(Amp reading on U lug)
NOTE
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
FIGURE 15. Voltage Selector Switch 240/120V Single Phase
Position
FIGURE 16. AC Voltmeter
Change-over switch
(Reading the W-U leg on
the outputerminal panel)
60
FIGURE 17. AC Voltmeter
Gauge
(Volt reading on W-U Lug)
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 35
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
240/120V Hard Wire Hookup
480/240V Hard Wire Hookup
The output terminal panel, when suppling single phase 120
volts, will provide three legs available with 183 amps each
on three different circuits. (See Figure 21 below.) The voltage
selector switch must be set at the single phase 240/120V
position. (See figure 20 below.)
The output terminal panel, when suppling single phase 240
volts, will provide one leg only with 91.6 amps available.
(See Figure 23) when the voltage selector switch is at the
single phase 240/120V position.
The output terminal panel, when suppling three phase 240
volts, will provide one circuit available at 198 amps with any
two wires plus the ground. (See Figure 23 below.) The voltage
selector switch must be set at the three phase 480/277V
position. (See figure 22 below.)
The output terminal panel, when suppling 3 phase 480 volts,
will provide one circuit available at 99 amps available with
all three wires plus ground. (See Figure 23) when the voltage
selector switch is set at the three phase 480/277V position.
FIGURE 20. Voltage Selector Switch 240/120V Single Phase
Position
FIGURE 22. Voltage Selector Switch 480/277V Three Phase
Position
FIGURE 21. Hard Wire Hook-up at 240/120V Position
FIGURE 23. Hard Wire Hook-up at 480/240V Position
PAGE 36 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
Voltage Selector Switch- 3 Phase 480/277V Position
The following are additional voltages available when the
voltage selector switch is in the 3 phase 480/277V
position. (See figure 24 below.)
Single Phase: 480V, 440V, or 416 Volt
The following connection, with the voltage selector switch
locked into the 3 phase 480/277V position (See Figure 24),
can offer SINGLE PHASE power at 480V, 440V, or 416V.
After hooking up the hard wires to the lugs as shown in
figure 27 below, 480V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 440 volt will be
reached when the Voltage Regulator Knob is turned down,
and 416 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 25).
FIGURE 25. Voltage
Selector Switch 270/120V
Single Phase
Position
FIGURE 24. Voltage Selector Switch 480/277V Single Phase
Position
3 Phase, 480V, 440V, or 416 Volt
The following connection, with the voltage selector switch
locked into the 3 phase 480/277V position (See Figure 24),
can offer THREE PHASE power at 480V, 440V, or 416V.
After hooking up the hard wires to the lugs as shown in
figure 28 below, 480V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 440 volt will be
reached when the Voltage Regulator Knob is turned down,
and 416 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 25).
FIGURE 26. Hard Wire Hook-up for Three Phase 480V, 440V,
or 416V
FIGURE 27. Hard Wire Hook-up for Single Phase 480V, 440V,
or 416V
Single Phase: 277V, 254V, or 240V
The following connection, with the voltage selector switch
locked into the 3 phase 480/277V position (See Figure 28),
can offer SINGLE PHASE power at 277V, 254V, or 240V.
After hooking up the hard wires to the lugs as shown in
figure 28 below, 277V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 254 volt will be
reached when the Voltage Regulator Knob is turned down,
and 240 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 25).
FIGURE 28. Hard Wire Hook-up for Single Phase 277V, 254V,
or 240V
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 37
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
Voltage Selector Switch- 3 Phase 240/139V Position
The following are additional voltages available when the
voltage selector switch is in the 3 phase 240/139V
position. (See Figure 29 below.)
Single Phase: 240V, 220V, or 208 Volt
The following connection, with the voltage selector switch
locked into the 3 phase 240/139V position (See Figure 29),
can offer SINGLE PHASE power at 240V, 220V, or 208V.
After hooking up the hard wires to the lugs as shown in
figure 32 below, 240V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 220 volt will be
reached when the Voltage Regulator Knob is turned down,
and 208 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 30).
FIGURE 30. Voltage
Regulator Knob located
on the control panel
FIGURE 29. Voltage Selector Switch 240/139V Three Phase
Position
FIGURE 32. Hard Wire Hook-up for Single Phase 240V, 220V,
or 208V
3 Phase, 240V, 220V, or 208 Volt
The following connection, with the voltage selector switch
locked into the 3 phase 240/139V position (See Figure 29),
can offer THREE PHASE power at 270V, 220V, or 208V.
After hooking up the hard wires to the lugs as shown in
figure 31 below, 240V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 220 volt will be
reached when the Voltage Regulator Knob is turned down,
and 208 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 30).
Single Phase: 139V, 127V, or 120V
The following connection, with the voltage selector switch
locked into the 3 phase 240/139V position (See Figure 29),
can offer SINGLE PHASE power at 139V, 127V, or 120V.
After hooking up the hard wires to the lugs as shown in
figure 33 below, 139V will be the voltage with the Voltage
Regulator Knob turned toward maximum. 127 volt will be
reached when the Voltage Regulator Knob is turned down,
and 120 volt when the Voltage Regulator Knob is toward
the lowest setting (See Figure 30).
FIGURE 31. Hard Wire Hook-up for Three Phase 240V, 220V,
or 208V
FIGURE 33. Hard Wire Hook-up for Single Phase 139V, 127V,
or 120V
PAGE 38 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — OUTPUT TERMINAL PANEL OVERVIEW
Voltage Selector Switch- Single Phase 240/120V
Position
The following are additional voltages available when the
voltage selector switch is in the single phase 240/120V
position. (See Figure 34 below)
Single Phase: 120 Volt
The following connection, with the voltage selector switch
locked into the single phase 240/120V position (See
Figure 34), will offer SINGLE PHASE power at 120V. After
hooking up the hard wires to the lugs as shown in figure 37
below, use the Voltage Regulator Knob to fine tune to
120V. (See Figure 35).
FIGURE 35. Voltage
Regulator Knob located
on the control panel
FIGURE 34. Voltage Selector Switch 240/120V Single Phase
Position
FIGURE 37. Hard Wire Hook-up for Single Phase, 120 volt
Single Phase, 240 Volt
The following connection, with the voltage selector switch
locked into the single phase 240/120V position (See
Figure 34), will offer SINGLE PHASE power at 240V. After
hooking up the hard wires to the lugs as shown in figure 36
below, use the Voltage Regulator Knob to fine tune to
240V. (See Figure 35)
FIGURE 36. Hard Wire Hook-up for Single Phase 240 volt
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 39
DCA-85SSJU — INSTALLATION
Outdoor Installation
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so that the exhaust will not
be discharged in the direction of nearby homes.
CAUTION :
An electric shock may happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from Generator Grounding
excessive moisture. Failure to do will result in deterioration To guard against electrical shock and possible damage to
of the insulation and will result in short circuits and grounding. the equipment, it is important to provide a good EARTH
ground.
Foreign materials such as dust, sand, lint and abrasive Article 250 (Grounding) of the National Electrical Code (NEC)
materials have a tendency to cause excessive wear to provides guide lines for proper grounding and specifies that
engine and alternator parts.
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
CAUTION :
Pay close attention to ventilation when NEC articles 250-64(b) and 250-66 set the following
operating the generator inside tunnels and grounding requirements:
caves. The engine exhaust contains 1. Use one of the following wire types to connect the
noxious elements. Engine exhaust must be
generator to earth ground.
routed to a ventilated area.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 38) connect the
Indoor Installation
ground cable between the lock washer and the nut on
Exhaust gases from diesel engines are extremely poisonous.
the generator and tighten the nut fully. Connect the other
Whenever an engine is installed indoors the exhaust fumes
end of the ground cable to earth ground.
must be vented to the outside. The engine should be installed 3. NEC article 250-52(c) specifies that the earth ground
at least two feet from any outside wall. Using an exhaust
rod should be buried a minimum of 8 ft. into the ground.
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat
excessively and possibly burn the valves.
NOTE
Mounting
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
The generator must be mounted on a solid foundation (such
electrician.
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are to
resist damage to the bottom of the generator and to maintain
alignment.
PAGE 40 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — INSTALLATION
Figure 38.
Typical Generator Grounding Application
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 41
DCA-85SSJU — PRE-SETUP
General Inspection Prior to Operation
The DCA-600SSK generator has been thoroughly
inspected and accepted prior to shipment from the factory.
However, be sure to check for damaged parts or
components, or loose nuts and bolts, which could have
occurred in transit.
Extension Cable
When using extension cords or cables, the distance,
length, and cable size should be considered when
using them to power various loads. Cables should be
sized to allow for distance in length and amperage so
that the voltage drop between the generator and point
of use (load) is held to a minimum. This is
determined from its load current, length and thickness
according to the following this equation for threephase, three-line system:
Circuit Breakers
To protect the generator from an overload, a 3-pole, 250 amp,
main circuit breaker is provided to protect the UVW output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit breakers
have also been provided to protect the load side of the
generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
e=1/58 x L/S x I x 1.723
e=voltage drop (V), L=cable length (m), S=cable
thickness (mm 2), and I=load current (A). Be sure to
select the cable length and thickness that will not
exceed the voltage drop by 5%.
PAGE 42 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — PRE-SETUP
Lubrication Oil
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
and verify that the oil level is maintained between the two
notches (Figure 39) on the dipstick. See Table 11 for proper
selection of engine oil.
Fuel
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 23,
Specification Table 7.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION
CAUTION:
Never fill the fuel tank while the engine is
running or in the dark. Diesel spillage on a
hot engine can cause a fire or explosion.
If diesel spillage occurs, wipe up the spilled
diesel completely to prevent fire hazards.
Coolant
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced.
Figure 39. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is not clean, drain the oil by
removing the oil drain plug, and refill with the specified amount
of oil as outlined in the John Deere Engine Owner's
Manual.
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system. See the engine
manual for further details.
Table 11. Recommended Motor Oil
Temperature Range
Type Oil
122° F ~ 32° F
(50° C ~ 0°C)
SAE 15W-40 or SAE40
32° F ~ -22° F
(0° C ~ -30°C)
SAE 5W-30
Below 5° C (-15°)
SAE 0W-30
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 43
DCA-85SSJU — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
12 for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Cleaning the Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the machine is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the John Deere Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the John
Deere Engine Owner's Manual.
Table 12. Coolant Capacity
Engine and Radiator
6.9 Gal. (26 liters)
Reserve Tank
2 Quarts (1.9liters)
The fan belt tension is proper if the fan belt bends 7 to 10
mm (Figure 40) when depressed with the thumb as shown
below.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 13) has been added.
Figure 40. Fan Belt Tension
CAUTION :
Table 13. Anti-Freeze Operating Temperatures
Freezing Point
Boiling Point
°C
°F
°C
°F
40
-24
-12
106
222
50
-37
-34
108
226
Vol %
Anti-Freeze
NOTE
When the antifreeze is mixed with
water, the antifreeze mixing ratio must
be less than 50%.
Never place hands near the belts or fan while
the generator set is running.
Battery
This unit is of negative ground DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68 F). If the specific gravity
should fall to 1.245 or lower, it indicates the battery is
discharged and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help inhibit corrosion.
PAGE 44 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — PRE-SETUP
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 41) are properly
connected to the battery terminals as shown below. The
RED cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
Inadequate battery connections may cause
poor starting of the generator, and create
other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 41. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
CAUTION :
If the battery cable is connected
incorrectly, electrical damage to the
generator will occur. Pay close attention
to the polarity of the battery when
connecting the battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the Off/Manual/Auto switch is in either
the manual or auto position (ON). ALWAYS make sure
that the Off/Manual/Auto switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 45
DCA-85SSJU — LOAD APPLICATION
Single Phase Load
CAUTION
CAUTION:
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Motors and motor-driven equipment
draw much greater current for starting
than during operation.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable
which cannot carry the required load can cause a voltage
drop which can burn out the appliance or tool and overheat
the cable.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 0.8. See Table 14
below when connecting loads.
Table 14. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
Common power tools
0.8
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
 When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
 When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
 When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
NOTE
If output (kVA) is not given on the equipment
nameplate, approximate output may be
determined by multiplying voltage by
amperage by 1.732.
PAGE 46 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
emissions. ALWAYS ventilate the
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UVW terminals as shown in
Figure 44. These terminals can be found on the output
terminal panel, (see page 32 Figure 14 for description
and usage of receptacles). To gain access to the output
terminals lift the UVW cover. Tighten terminal nuts
securely to prevent load wires from slipping out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 7 on page 37).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel.
If diesel spillage occurs, completely wipe up the spilled
fuel immediately.
Figure 44. UVW Terminal Lugs (Load)
3. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 45).
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the
main, GFCI or load circuit breakers
in the ON position.
1.
Be sure to disconnect the
electrical load and switch the main, load and G.F.C.I.
circuit breakers (Figure 43) to the “OFF” position prior to
starting the engine.
IVE
ST
PO
E
TIV
GA
NE
RY
E
TT
A
B
Figure 45. Battery Connections
Figure 43. Main, GFCI and
Load Circuit Breakers
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 47
DCA-85SSJU — GENERATOR START-UP PROCEDURE
4. Close all engine enclosure doors (Figure 46).
Figure 46. Engine Enclosure Doors
5. When starting the generator in COLD weather conditions,
press and hold the engine preheat button (Figure 47) .
8. Turn the Auto-Off/Reset-Manual switch to ‘Manual’ to
start the engine (Figure 50). Once the engine
starts, let the engine run for 1-2 minutes. Listen for
any abnormal noises.
Figure 50. Auto-Off/Reset-Manual Switch
9. Once the engine is warm and the engine is running
properly, set the engine speed switch to ‘High’
(Figure 51).
Figure 47. Engine Pre-Heat Button
6. Check the voltage selection switch is at the desired
voltage (Figure 48).
Figure 51. Engine Speed Switch (high)
10. The generator's frequency meter (Figure 52)displays the
60 cycle output frequency in HERTZ.
Figure 48. Voltage Selection Switch
Figure 52. Frequency Meter (Hz)
7. Set engine speed switch to ‘Low’ (Figure 49).
11. The generator's voltage meter (Figure 53) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob (Figure 54) to increase or
decrease the desired voltage.
Figure 49. Engine Speed Switch (low)
Figure 53. Voltmeter
PAGE 48 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — GENERATOR START-UP PROCEDURE
15. The tachometer (Figure 58) will indicate the speed of
the engine when the generator is operating. Under normal
operating conditions this speed is approximately 1800
RPM’s.
Figure 54. Voltage Adjust Control Knob
12. The ammeter (Figure 55) will indicate zero amps with no
load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator’s alternator.
20
40
60
0
Figure 58. Engine Tachometer
16. Turn the MAIN, GFCI and LOAD circuit breakers to
their ON position (Figure 59).
75
A
Figure 55. Ammeter (No Load)
13. The engine oil pressure gauge (Figure 56) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
25 psi.
Figure 59. Main and GFCI Circuit Breakers
17. Observe the generator's ammeter (Figure 60) and verify
it reads the anticipated amount of current with respect
to the load. The ammeter will only display a current
reading if the load is in use.
20
40
60
0
75
Figure 56. Oil Pressure Gauge
14. The coolant temperature gauge (Figure 57) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature is between 165 and
215 degrees Fahrenheit.
A
Figure 60. Ammeter (Load)
18. The generator will run until manually stopped or an
abnormal condition occurs.
WATER
TEMP
Figure 57. Coolant Temperature Gauge
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 49
DCA-85SSJU — GENERATOR START-UP PROCEDURE (AUTO)
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
CAUTION:
When connecting the generator to a
isolation (transfer) switch, ALWAYS have
power applied to the generator's internal
battery charger. This will ensure that the
engine will not fail due to a dead battery.
Starting the generator in the "AUTO" mode is similar to
starting the generator in the "MANUAL" mode, with a few
exceptions.
CAUTION:
When running the generator in the AUTO
mode, remember the generator can start
up at any time without warning. NEVER
attempt to perform any maintenance
when the generator is in the auto mode.
When starting generator in Auto mode use the "Manual Startup" procedure except where noted (see below).
1. Perform steps 1 through 10 (Before Starting, page 4748) as outlined in the manual starting procedure.
2. Place the Off/Manual/Auto switch (Figure 61) in the
AUTO position .
Figure 61. Off/Manual Auto Switch (AUTO)
3. Continue to follow the steps outline in the manual startup procedure (start at step 12, page 50).
PAGE 50 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU— GENERATOR SHUT DOWN PROCEDURE
ENGINE SHUTDOWN
To shutdown the generator, use the following procedure:
1. Switch both the MAIN, GFCI and LOAD circuit breakers
(Figure 62) to the “OFF” position.
Figure 62. Main, GFCI and Load
circuit breakers
2.
Set the engine speed switch (Figure 63) to the idle
(low) position.
Figure 63. Engine Speed Switch
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
4. Turn the Auto-Off/Reset-Manual switch from the engine
controller to “OFF/Reset” position (Figure 64).
Figure 64. Off/Manual Auto Switch
5.
Remove the load from the UVW terminal strip.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 51
DCA-85SSJU — MAINTENANCE
General Inspection
Cleaning the Fuel Strainer
Prior to each use, the generating set should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel
or oil leaks.
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in diesel. Securely
fasten the fuel strainer cap so that fuel will not leak. Check
the fuel strainer every 200 hours of operation or once a month.
Engine Side, Fuel, Oil and Coolant (Refer to the Engine
Instruction Manual)
Check Oil Level
Air Cleaner
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
Fuel Addition
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
Removing Water from the Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the greater
the empty volume inside the tank, the easier it is for water
to condense. This can be reduced by always keeping the
tank as full as possible.
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level. The oil level
must be between the two notches on the dipstick as shown
in page 39, Figure 13.
Generator Storage
For storage of the generator for over 30 days, the following
is required:
 Drain the fuel tank completely.
 Completely drain the oil from the crankcase and refill
with fresh oil.
 Clean all external parts of the generator with a cloth.
 Cover the generating set and store in a clean, dry place.
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the key switch to the
“START” position for 15-30 seconds. Try again, if needed.
This unit is equipped with an automatic air bleeding system.
Service Daily
If engine is operating in very dusty and dry grass conditions,
a clogged air cleaner will result in high fuel consumption,
loss of power and excessive carbon buildup in the
combustion chamber.
PAGE 52 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — MAINTENANCE
Maintenance - Table 15
INSPECTION / MAINTENANCE
ENGINE
10 Hrs
DAILY
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Par ts
X
250 Hrs
Replace Engine Oil and Filter *1
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
2
GENERATOR
500 Hrs
Change Fuel Filter *
X
Clean Radiator and Check Coolant Protection
Level
X
1000 Hrs
Replace Air Filter Element
X
Change Corrosion Resistor
X
Check all Hoses and Clamps
X
Clean Inside of Fuel Tank
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 53
DCA-85SSJU — GENERATOR WIRING DIAGRAM
PAGE 54 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENGINE WIRING DIAGRAM
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 55
DCA-85SSJU — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for
diagnosis based on the Engine Troubleshooting (Table 16). If
the problem cannot be remedied, consult our company's
business office or service plant.
TABLE 16. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
Starter does not run.
PAGE 56 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — TROUBLESHOOTING (ENGINE)
TABLE 16. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not smooth.
Either white or blue exhaust gas
is observed.
Either black or dark gray exhaust
gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 57
DCA-85SSJU — TROUBLESHOOTING (GENERATOR)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for
diagnosis based on the Generator Troubleshooting (Table17)
or Engine Controller Troubleshooting (Table 18). If the problem
cannot be remedied, consult our company's business office
or service plant.
TABLE 17. GENERATOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Check and replace.
Is engine speed correct?
Turn engine throttle lever to "High".
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated?
Confirm load requirement and replace.
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
PAGE 58 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — TROUBLESHOOTING (ENGINE CONTROLLER)
TABLE 18. ENGINE CONTROLLER TROUBLESHOOTING
Sympton
Low oil pressure light is
on.
Low coolant level light
is on.
High coolant
temperture light is on.
Possible Cause
Solution
Low oil level?
Fill oil level.
Oil pressure sending unit failure?
Replace oil pressure sending unit.
Time delay malfuntion in controller?
Refer to dealer.
Wire shorted?
Inspect/repair wire.
Low coolant level?
Fill coolant level.
Sending unit failure?
Replace sending unit.
Low battery voltage?
Replace/charge battery.
Fan belt tension incorrect?
Tighten/replace fan belt.
Air flow is not circulation through radiator?
Clean/repair radiator grill.
Doors open?
Close doors.
Exhaust leaking?
Replace/repair gaskets or faulty part.
Generator being overloaded?
Check/reduce load.
Thermostat failure?
Replace thermostat.
Air intake blocked?
Clear all air intakes.
Temperature switch failure?
Replace temperature switch.
No or low Fuel?
Fill fuel level.
Engine Controller needs to be calibrated?
Refer to dealer.
RPM engine speed too high?
Adjust RPM.
Governor actuator needs to be adjusted?
Adjust governor actuator.
Governor controller needs to be adjusted?
Adjust governor controller.
Engine Controller needs to be calibrated?
Refer to dealer.
MPU out of adjustment?
Adjust MPU.
MPU dirty?
Clean MPU.
Overcrank light is on.
Overspeed light is on.
Loss of MPU (magnetic
pick up) light(s) or on.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 59
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
*
+, or % belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
PAGE 60 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — SUGGESTED SPARE PARTS
DCA-85SSJU W/JOHN DEERE DIESEL ENGINE
1 to 5 Units
Qty.
P/N
Description
10 .............. 6125817032 .....................AIR FILTER
10 .............. 6003118293 .....................FUEL FILTER
10 .............. 6002111231 .....................OIL FILTER
5 ................ 6004111151 .....................CARTRIDGE, CORROSION RESISTOR
1 ................ 0601840487 .....................CIRCUIT BREAKER
2 ................ 0412121757 .....................ENGINE FAN BELT
1 ................ 6008155390 .....................SWITCH, STARTER
5 ................ 615 ...................................KEY SET, STARTER SWITCH (2)
2 ................ 0602122281 .....................OIL SWITCH
1 ................ 6152611520 .....................RADIATOR HOSE (UPPER)
1 ................ 6152611531 .....................RADIATOR HOSE (LOWER)
1 ................ 0802010900 .....................FUEL CAP
1 ................ 061820625 .......................AUTOMATIC VOLTAGE REGULATOR
1 ................ 0601807373 .....................MAIN CIRCUIT BREAKER
1 ................ 0601805840 .....................CIRCUIT BREAKER
1 ................ 0601810072 .....................PILOT LAMP
2 ................ 0601810261 .....................BULB, PILOT LAMP
1 ................ 23S0311150M ..................CAP, RADIATOR
1 ................ 0602122200 .....................UNIT, OIL PRESSURE
1 ................ 0602123206 .....................UNIT, WATER TEMPERATURE
1 ................ 0602121052 .....................CHARGING AMMETER
NOTE
Part number on this Suggested Spare
Parts list may supercede/replace the
P/N shown in the text pages of this
book.
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 61
GENERATOR ASSY.
DCA-85SSJU — GENERATOR ASSY.
GENERATOR ASSY.
PAGE 62 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — GENERATOR ASSY.
GENERATOR ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
PART NO.
B6110000102
8101070033
8101611004
8101015003
012010030
0042510000
030210250
0601821349
0601822601
8001020004
8001020504
0010110020
0040010000
0601000209
0071906311
B6130000203
0845041804
8101315202
8101350013
0012110070
0042610000
031110160
0010110035
0040010000
031110160
8101310014
8131312014
8101331003
0105050616
8101333003
0010106030
0040006000
952404470
8101614003A
0343204170
EM923344
0070506306
0012810035
0012810030
8111332014
020106050
0605000010
0030012000
0040012000
031112230
PART NAME
QTY.
REMARKS
ROTOR ASS’Y
1
FIELD ASS’Y
1
FAN
1
COUPLING DISK
5
BALANCING PLATE
1
HEX. HEAD BOLT .............................. 8 ...........REPLACES 0012110030
LOCK WASHER
8
SET PLATE, RECTIFIER ................... 1 ...........REPLACES 8101026013
RECTIFIER ........................................ 2 ...........PT 3610
SURGE ABSORBER .......................... 1 ...........ERZ- M14JK621A
INSULATOR WASHER
1
INSULATOR WASHER
1
HEX. HEAD BOLT
4
LOCK WASHER
4
BALANCING WEIGHT KIT
1
BEARING ........................................... 1 ...........6311 DDU C3
STATOR ASS’Y
1
GROMMET
2
END BRACKET
1
FIELD ASS’Y, EXCITER
1
HEX. HEAD BOLT
4
LOCK WASHER
4
PLAIN WASHER ................................. 4 ...........REPLACES 0041210000
HEX. HEAD BOLT
6
LOCK WASHER
6
PLAIN WASHER ................................. 6 ...........REPLACES 0041210000
COVER, BEARING
1
GASKET, BEARING
1
COVER, END BRACKET
1
HEX. HEAD BOLT ............................ 10 ..........REPLACES 0017106012
COVER, END BRACKET
1
HEX. HEAD BOLT
2
LOCK WASHER
2
PLAIN WASHER ................................. 2 ..........REPLACES 0041206000
COUPLING RING ............................... 1 ..........REPLACES M2163400003
HEX. HEAD BOLT
8
LOCK WASHER .................................. 8 ..........REPLACES 0043604000
BEARING ........................................... 1 ..........6306ZZ
HEX. HEAD BOLT
8
HEX. HEAD BOLT
12
COVER, FAN
1
NUT .................................................... 1 ..........REPLACES 0600815000
RUBBER SUSPENSION
2
HEX. NUT
2
LOCK WASHER
2
PLAIN WASHER ................................. 2 ..........REPLACES 0041212000
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 63
DCA-85SSJU — CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 64 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NO.
M2248700104
M2215000002
0601808814
0021005080
0601823863
0021304015
0601820671
0027105015
0601806118
011808015
0601820846
0601820845
0021304015
0030004000
LY2US12VD
PTF08AE
PYCA1
0027104020
M2213500103
011106015
M3923100004
M2215600003
EDGEGES
0027103010
011106015
M2215600104
011106015
011106015
0040506000
M2223000103
0601807630
0601807641
PART NAME
QTY.
REMARKS
WIRE HARNESS, GENERATOR
1
CONTROL BOX
1
CIRCUIT BREAKER .................................... 1 .......... KAF362501021 3P 250A
MACHINE SCREW
4
RELAY UNIT ............................................... 2 .......... MSA9013A
MACHINE SCREW ...................................... 4 .......... REPLACES 0027104015
AUTOMATIC VOLTAGE REGULATOR .......... 1 .......... NTA5A2DB
MACHINE SCREW
4
CURRENT TRANSFORMER ....................... 3 .......... 814943 200 /5A
MACHINE SCREW ...................................... 6 .......... REPLACES 0027106015
OVER CURRENT RELAY ............................ 1 .......... LA7D1064
OVER CURRENT RELAY ............................ 1 .......... LR2D1308
MACHINE SCREW ...................................... 2 .......... REPLACES 0027104015
HEX. NUT .................................................... 2 .......... REPLACES 0207004000
RELAY .........................................................1 .......... REPLACES 0601823768
BASE .......................................................... 1 .......... REPLACES 0601823109
CLIP ............................................................ 2 .......... REPLACES 0601824400
MACHINE SCREW
2
CONTROL BOX COVER
1
HEX. HEAD BOLT ....................................... 4 .......... REPLACES 0016906015
SELECTOR SWITCH .................................. 1 .......... VY 125
SWITCH BRACKET
1
EDGING ...................................................... 2 .......... REPLACES 0330000295
MACHINE SCREW
4
HEX. HEAD BOLT ....................................... 6 .......... REPLACES 0016906015
SWITCH COVER
1
HEX. HEAD BOLT ....................................... 4 .......... REPLACES 0016906015
HEX. HEAD BOLT ....................................... 8 .......... REPLACES 0016906015
TOOTHED WASHER
1
CONTROL PANEL
1
FREQUENCY METER ................................ 1 .......... UP TO S/N7700090;
264250DJDJ9
FREQUENCY METER ................................ 1 .......... S/N7700091~;
FCF645~65Hz 240V
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 65
CONTROL BOX ASSY.
DCA-85SSJU — CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 66 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
27
PART NO.
0601808953
0601808988
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
0601801040
0601806813
0601806859
0601801041
0601840073
0601840121
M1223100004
0027105010
0027105010
M9220100004
0080200007
DYN110794000012
0027105015
0602120485
0602202592
011808015
LY2DDC12V
PTF08AE
PYCA1
0027104020
0601821370
0027104020
PART NAME
QTY.
REMARKS
AC AMMETER ............................................ 1 .......... UP TO S/N7700090;
260240LSLS1JCA
AC AMMETER ............................................ 1 .......... S/N7700091~;
ACF6 0-800A, 0-400A/5A
CHANGE- OVER SWITCH, AMMETER ..... 1 .......... SL- 2AS
AC VOLTMETER ......................................... 1 .......... UP TO S/N7700090;260244SJSJ1
AC VOLTMETER ......................................... 1 .......... S/N7700091~; SCF6 0-600V
CHANGE- OVER SWITCH, VOLTMETER ... 1 .......... SL- 2VS
RHEOSTAT ( VOLTAGE REGULATOR ) ....... 1 .......... RA20A2SE102BJ 2W 1K OHM
KNOB
1
STOPPER
1
MACHINE SCREW
2
MACHINE SCREW
4
SET SCREW
1
SNAP RING
1
CONTROLLER ............................................ 1 .......... REPLACES 0602202599
MACHINE SCREW
4
SPEED SENSOR ....................................... 1 .......... MPS6724
STARTER RELAY ........................................ 1 .......... AT141011
MACHINE SCREW ...................................... 2 .......... REPLACES 0027106015
RELAY .........................................................1 .......... REPLACES 0601827656
BASE .......................................................... 1 .......... REPLACES 0601823109
CLIP ............................................................ 2 .......... REPLACES 0601824400
MACHINE SCREW
2
RECTIFIER ................................................. 2 .......... REPLACES 0601823240
MACHINE SCREW
1
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 67
ENGINE & RADIATOR ASSY.
DCA-85SSJU — ENGINE AND RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
PAGE 68 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENGINE AND RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
PART NO.
M2925200014
0602011490
0602041290
0602042590
0602014297
M2303200303
011008020
0040012000
0605000009
0030012000
0040012000
0602012743
0602011065
0015908020
M2310500503
M2310500603
0605515147
0605515201
0602046582
0602046365
0602040651
0602040554
M2375200004
011008020
020108060
0016908030
M2375100003
0605515146
0605515200
0602022563
0602022561
0603306590
0603300285
0605511395
0603306395
0602021070
0269200600
M9300000103
M9300100003
PART NAME
QTY.
REMARKS
ENGINE ...................................................... 1 .......... JOHN DEERE 4045TF250
FAN BELT
1
ELEMENT, OIL FILTER ............................... 1 .......... RE59754A
ELEMENT, FUEL FILTER ............................ 1 .......... RE62418
ELECTRIC HEATER .................................... 1 .......... RE29658
ENGINE FOOT
2
HEX. HEAD BOLT ....................................... 6 .......... REPLACES 0010312030
LOCK WASHER
6
RUBBER SUSPENSION
2
HEX. NUT
2
LOCK WASHER
2
RADIATOR ................................................... 1 .......... C2810030001
CAP ............................................................. 1 .......... C89C0115010
HEX. HEAD BOLT
6
RADIATOR HOSE
1
RADIATOR HOSE
1
HOSE BAND
3
HOSE BAND
1
AIR CLEANER ............................................ 1 .......... FPG082527
ELEMENT, AIR CLEANER .......................... 1 .......... P828889
INDICATOR, AIR CLEANER ........................ 1 .......... RBX002352
BAND, AIR CLEANER
1
BRACKET, AIR CLEANER
1
HEX. HEAD BOLT ....................................... 4 .......... REPLACES 0016908020
HEX. NUT .................................................... 4 .......... REPLACES 0207008000
HEX. HEAD BOLT
2
HOSE, AIR CLEANER
1
HOSE BAND
1
HOSE BAND
1
ADAPTER
1
90 ELBOW
1
CONNECTOR
1
ROCKNUT
1
VALVE
1
HOSE JOINT
1
CAP ............................................................. 1 ...........10FNTX- S
DRAIN HOSE
1
RESERVE TANK
1
CAP, RESERVE TANK
1
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 69
ENGINE & RADIATOR ASSY.
DCA-85SSJU — ENGINE AND RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
PAGE 70 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENGINE AND RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
NO.
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
PART NO.
0199100175
M2316100114
011008020
M2260600024
012210020
0602202592
020106050
011808015
M2483400014
011206020
0602122281
M9200100704
0602123282
M9200100404
0602060000
0602061000
0012110095
030210250
DYNC70025000012
M3356200004
012210020
011206020
0207006000
PART NAME
QTY.
REMARKS
HOSE
1
BRACKET, RESERVE TANK ....................... 1 .......... REPLACES M2316100204
HEX. HEAD BOLT ....................................... 2 .......... REPLACES 0016908020
RELAY BRACKET
1
HEX. HEAD BOLT ....................................... 1 .......... REPLACES 0017110020
RELAY .........................................................1 .......... AT141011
HEX. NUT .................................................... 2 .......... REPLACES 0030006000
MACHINE SCREW ...................................... 2 .......... REPLACES 0027106015
ALTENATOR COVER
1
HEX. HEAD BOLT ....................................... 2 .......... REPLACES 0016906020
OIL SWITCH ............................................... 1 .......... 1718939011
ADAPTER
1
WATER SWITCH ......................................... 1 .......... 1518183041
ADAPTER
1
BLOWER FAN ............................................. 1 .......... REPLACES 0602060011
FAN SPACER .............................................. 1 .......... R81911
HEX. HEAD BOLT
4
LOCK WASHER ........................................... 4 .......... REPLACES 0042510000
ACTUATOR .................................................. 1 .......... REPLACES 0602150093
STOPPER BRACKET
1
HEX. HEAD BOLT ....................................... 1 .......... REPLACES 0017110020
HEX. HEAD BOLT ....................................... 1 .......... REPLACES 0017106020
HEX. NUT
1
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 71
DCA-85SSJU — ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 72 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART NO.
M2357200062
0602120096
0602122093
0602122272
0602123092
0602123261
0602121080
0602125090
0601831585
0601831586
0601831395
ECU9988N
82608
0027104035
0030004000
0601810141
0601831330
PART NAME
QTY.
REMARKS
WIRE HARNESS, ENGINE
1
TACHOMETER ............................................ 1 .......... 103678
OIL PRESSURE GAUGE ............................ 1 .......... 100174
UNIT, OIL PRESSURE ................................ 1 .......... 108497
WATER TEMPERATURE GAUGE ............... 1 .......... 100182
UNIT, WATER TEMPERATURE ................... 1 .......... 0202500
CHARGING AMMETER .............................. 1 .......... 100158
FUEL GAUGE ............................................. 1 .......... 100176
PREHEAT BUTTON .................................... 1 .......... 44047
CAP ............................................................. 1 .......... 44053
ENGINE SPEED SWITCH .......................... 1 .......... 7302K36
ENGINE CONTROLLER .............................. 1 .......... REPLACES 0602202545
SWITCH ...................................................... 1 .......... REPLACES 0601831340
MACHINE SCREW
2
HEX. NUT .................................................... 2 .......... REPLACES 0207004000
PANEL LIGHT .............................................. 1 .......... 9826800370
SWITCH, PANEL LIGHT ............................. 1 .......... 900001
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 73
OUTPUT TERMINAL ASSY.
DCA-85SSJU — OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
PAGE 74 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
PART NO.
M3230700003
M9220100304
0801830804
0039316000
0040016000
0041416000
0012108035
M2238100003
M3236100104
0605010040
0027103010
0207003000
S8413
0027103010
0207003000
011106015
011106015
M3236400004
M3236300004
011106015
0601808803
0601808804
M1260700304
0222100150
011106015
0601812597
0601811034
0021304015
0030004000
0601815194
0021304015
PART NAME
QTY.
REMARKS
TERMINAL PANEL
1
OUTPUT TERMINAL BOLT
5
TIE BOLT .................................................... 5 .......... REPLACES M9220100404
HEX. NUT
10
LOCK WASHER
15
PLAIN WASHER
20
HEX. HEAD BOLT ...................................... 5 .......... REPLACES 0016908035
TERMINAL COVER
1
OUTPUT WINDOW
1
HINGE ........................................................ 2 .......... TH- TM122
MACHINE SCREW
4
HEX. NUT ................................................... 4 .......... REPLACES 0030003000
PLAIN WASHER ......................................... 4 .......... REPLACES 0041203000
MACHINE SCREW
4
HEX. NUT ................................................... 4 .......... REPLACES 0030003000
HEX. HEAD BOLT ...................................... 2 .......... REPLACES 0016906015
HEX. HEAD BOLT ...................................... 4 .......... REPLACES 0016906015
CABLE OUTLET COVER
1
SUPPORTER, CABLE OUTLET COVER 1
HEX, HEAD BOLT ...................................... 6 .......... REPLACES 0016906015
CIRCUIT BREAKER ................................... 2 .......... QUO 120B 1P 20A
CIRCUIT BREAKER ................................... 3 .......... QOU 250B 2P 50A
BREAKER FITTING COVER
1
CUSHION RUBBER
1
HEX. HEAD BOLT ...................................... 2 .......... REPLACES 0016906015
RECEPTACLE;GF530EM 125V 20AX2 ...... 2 ...........REPLACES 0601812598
RECEPTACLE;CS6369 250V 50A; ............. 3 ...........REPLACES 0601812538
MACHINE SCREW ................................... 10 .......... REPLACES 0027104015
HEX. NUT ................................................. 10 .......... REPLACES 0207004000
TERMINAL BLOCK .................................... 1 .......... 601- GP- 02
MACHINE SCREW ..................................... 2 .......... REPLACES 0027104015
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 75
BATTERY ASSY.
DCA-85SSJU — BATTERY ASSY.
BATTERY ASSY.
PAGE 76 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — BATTERY ASSY.
BATTERY ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
PART NO.
551010280
M9310500014
M9103000304
06022209020
0040006000
M1346400204
M2346400104
011008020
0040508000
0017112025
0040512000
012210020
0040510000
PART NAME
QTY.
REMARKS
BATTERY .................................................... 1 .......... REPLACES 0602220187
BATTERY SHEET
1
BATTERY BAND
1
BATTERY BOLT SET
2
LOCK WASHER
2
BATTERY CABLE
1
BATTERY CABLE
1
HEX. HEAD BOLT ....................................... 1 .......... REPLACES 0016908020
TOOTHED WASHER
1
CABLE
1
HEX. HEAD BOLT
1
TOOTHED WASHER
1
HEX. HEAD BOLT ....................................... 1 .......... REPLACES 0017110020
TOOTHED WASHER
1
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 77
MUFFLER ASSY.
DCA-85SSJU — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 78 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
PART NO.
0602300166
012210025
M2335000003
0602325066
M2333200004
0016908040
M2330400314
M2333399913
011106015
0602326060
PART NAME
QTY.
REMARKS
MUFFLER
1
HEX. HEAD BOLT ....................................... 4 .......... REPLACES 0016910025
EXHAUST PIPE
1
CLAMP ........................................................ 1 ......... MOO1432
GASKET ..................................................... 1 ......... REPLACES M2333200014
HEX. HEAD BOLT
4
COVER
1
BRACKET
1
HEX. HEAD BOLT ....................................... 4 .......... REPLACES 0016906015
U BOLT SET ............................................... 1 .......... 89545K
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 79
FUEL TANK ASSY.
DCA-85SSJU — FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 80 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART NO.
M2363000102
0605505070
M3363200104
M9310500104
011008020
0207308000
0222100178
M9200000003
M9200200004
0150000018
011206020
M1363400104
0605515198
0602042420
0602042601
0191300450
0191301600
0191302000
0605515189
0605515109
0602220911
PART NAME
QTY.
REMARKS
FUEL TANK
1
CAP, FUEL TANK
1
TANK BAND
2
SUPPORTER SHEET
4
HEX. HEAD BOLT ....................................... 2 .......... REPLACES 0016908020
HEX.NUT
2
RUBBER SHEET
4
DRAIN JOINT
1
DRAIN BOLT
1
O RING
1
HEX. HEAD BOLT ....................................... 2 .......... REPLACES 0016906020
DRAIN HOSE
1
HOSE BAND
2
FUEL FILTER .............................................. 1 .......... PTG15P
LEAK- OFF LINE ......................................... 1 .......... RE67050
SUCTION HOSE
1
SUCTION HOSE
1
RETURN HOSE
1
HOSE BAND
1
HOSE BAND
5
CLAMP
1
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 81
ENCLOSURE ASSY.
DCA-85SSJU — ENCLOSURE ASSY.
ENCLOSURE ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 82 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
PART NO.
M2415000203
M1413400004
011008020
M2425000003
M2495100503
011008020
M2423200214
M2495100404
011008020
M2423200313
011008020
M2435000203
M2433000303
0010114030
030214350
031114260
012212030
M2445000103
M2493300904
011008020
M2445300003
M2445300103
M2495300504
M2445300203
M2495300004
0207006000
011008020
M2443200123
M1443600204
020106050
952404470
B9114000002
0027106016
0030006000
M9110100204
M9116100004
011008020
0845031504
PART NAME
QTY.
REMARKS
BASE
1
UNDER COVER
1
HEX. HEAD BOLT ....................................... 2 .......... REPLACES 0016908020
FRONT FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ....................................... 6 .......... REPLACES 0016908020
COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT .................................... 11 .......... REPLACES 0016908020
INNER COVER, FRONT FRAME
1
HEX.HEAD BOLT ....................................... 7 .......... REPLACES 0016908020
CENTER FRAME
1
CENTER FRAME
1
HEX. HEAD BOLT
8
LOCK WASHER .......................................... 8 .......... REPLACES 0040014000
PLAIN WASHER ......................................... 8 .......... REPLACES 0041214000
HEX. HEAD BOLT .................................... 10 .......... REPLACES 0017112030
REAR FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ...................................... 4 .......... REPLACES 0016908020
REAR COVER
1
DUCT, REAR COVER
1
ACOUSTIC SHEET
1
DUCT, REAR COVER
1
ACOUSTIC SHEET
1
HEX. NUT
16
HEX. HEAD BOLT ...................................... 9 .......... REPLACES 0016908020
REAR DOOR
1
WINDOW PLATE
1
HEX. NUT ................................................... 8 .......... REPLACES 0207306000
PLAIN WASHER ......................................... 8 .......... REPLACES 0041206000
DOOR HANDLE ASS’Y .............................. 1 .......... REPLACES M9113000002
MACHINE SCREW ..................................... 4 .......... REPLACES 0021806015
HEX. NUT
4
HINGE
2
WASHER
2
HEX. HEAD BOLT ...................................... 3 .......... REPLACES 0016908020
BLIND PLUG .............................................. 2 .......... REPLACES M9310000004
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 83
ENCLOSURE ASSY.
DCA-85SSJU — ENCLOSURE ASSY.
ENCLOSURE ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 84 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
PART NO.
M2463000202
M2493500123
M2463500114
011008020
1625165103
1625165204
M2455200103
M2493300804
011208060
011008020
M2455000003
M2493400904
M2453000603
M2493401104
M2455000103
M2495400304
M2455000203
M2495400004
M2453300503
M2493401004
M2455300003
M2495400404
020706000
B9114000002
0027106016
020106050
M9110100204
M9110100304
M9116100004
011008020
0601850097
0027208025
0845031504
011008020
0040508000
M2455600004
0016906015
PART NAME
QTY.
REMARKS
ROOF PANEL
1
ACOUSTIC SHEET
1
OVER COVER, FRONT FRAME
1
HEX. HEAD BOLT .................................... 18 .......... REPLACES 0016908020
BONNET CAP ............................................ 1 .......... REPLACES M9310000103
CHAIN ASS’Y ............................................. 1 .......... REPLACES M1483600204
SPLASHER PANEL
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ...................................... 4 .......... REPLACES 0016908055
HEX. HEAD BOLT ...................................... 2 .......... REPLACES 0016908020
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
DUCT
1
ACOUSTIC SHEET
1
DUCT
1
ACOUSTIC SHEET
1
HEX. NUT
13
DOOR HANDLE ASS’Y ............................... 3 ......... REPLACES M19113000002
MACHINE SCREW .................................... 12 ......... REPLACES 0021806015
HEX. NUT .................................................. 12 ......... REPLACES 0030006000
HINGE
4
HINGE
4
WASHER
8
HEX. HEAD BOLT ....................................... 9 ......... REPLACES 0016908020
DOOR STOPPER
8
MACHINE SCREW
8
BLIND PLUG ............................................... 8 ......... REPLACES M9310000004
HEX. HEAD BOLT ....................................... 1 ......... REPLACES 0016908020
TOOTHED WASHER
1
DOOR BRACKET
1
HEX. HEAD BOLT
3
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 85
RUBBER SEALS ASSY.
DCA-85SSJU — RUBBER SEALS ASSY.
RUBBER SEALS ASSY.
PAGE 86 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — RUBBER SEALS ASSY.
RUBBER SEALS ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART NO.
0228901580
0229200825
0228900670
0228901090
M2492300004
0228800665
0228900425
0228900860
0228900630
0229200900
0229200840
0228800770
0228800540
0228800580
0228100550
0228100170
0228100350
0228100360
0228100180
PART NAME
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
SEAL RUBBER
QTY.
2
1
1
4
1
1
1
1
1
2
1
2
1
1
1
2
1
1
1
REMARKS
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 87
DCA-85SSJU — NAMEPLATE AND DECAL ASSY.
NAME PLATE ASSY.
PAGE 88 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
DCA-85SSJU — NAMEPLATE AND DECAL ASSY.
NAME PLATE ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
PART NO.
9039209064
C9522100003
C9595300004
M1550000204
M1550000703
M2552000104
M2552000203
M2552000303
M3552000103
M9500000004
M9500100004
M9500300004
M9500300104
M9500500004
M9500500104
M9503000004
M9503000103
M9503100004
M9503200004
M9510100004
M9510200002
M9520000004
M9520000104
M9520000204
M9520100004
M9520100204
M9520100304
M9520100404
M9520100503
M9520200003
0600500090
0021106015
M2560100003
M2560100103
M2560100203
M2560100403
M2562100004
PART NAME
QTY.
REMARKS
DECAL; START CONTACT .............................................. 1 ......... S- 4468
DECAL; CAUTION ........................................................... 2 ......... C9221 0000
DECAL; CAUTION ........................................................... 1 ......... C9053 0000
DECAL; NOTE ................................................................. 1 ......... M1500 0020
DECAL; AUXILIARY OUTPUT ......................................... 1 ......... M1500 0070
DECAL; NOTE ................................................................. 1 ......... M2520 0010
DECAL; ENGINE OPERATING ........................................ 1 ......... M2520 0020
DECAL; GENERATOR CONTROL ................................... 1 ......... M2520 0030
DECAL; OPERATING PROCEDURES ............................ 1 ......... M3520 0010
DECAL; OIL DRAIN PLUG ............................................... 1 ......... M9000 0000
DECAL; WATER ............................................................... 1 ......... M9001 0000
DECAL; - .......................................................................... 1 ......... M9003 0000
DECAL; + ......................................................................... 1 ......... M9003 0010
DECAL; DIESEL FUEL .................................................... 1 ......... M9005 0000
DECAL; FUEL DRAIN PLUG ........................................... 1 ......... M9005 0010
DECAL; WARNING MOVING PARTS............................... 2 ......... M9030 0000
DECAL; WATER - OIL CHECK ........................................ 1 ......... M9030 0010
DECAL; WARNING HOT COOLANT ............................... 1 ......... M9031 0000
DECAL; WARNING ENGINE EXHAUST .......................... 1 ......... M9032 0000
DECAL; CAUTION HOT PARTS....................................... 1 ......... M9101 0000
DECAL; MQ ..................................................................... 1 ......... M9102 0000
DECAL; GROUND ........................................................... 1 ......... M9200 0000
DECAL; AMMETER CHANGE- OVER SWITCH .............. 1 ......... M9200 0010
DECAL; VOLTMETER CHANGE- OVER SWITCH........... 1 ......... M9200 0020
DECAL; WARNING ELECTRIC SHOCK HAZARD .......... 2 ......... M9201 0000
DECAL; CAUTION ........................................................... 1 ......... M9201 0020A
DECAL; SAFETY INSTRUCTIONS .................................. 1 ......... M9201 0030
DECAL; DANGER HIGH VOLTAGE ................................. 1 ......... M9201 0040
DECAL; WARNING .......................................................... 1 ......... M9201 0050
DECAL; CONNECTION OF OUTPUT CABLE ................. 1 ......... M9292 0000
EMBLEM
1
MACHINE SCREW
2
STRIPE; WHISPERWATT
1
STRIPE; MQ POWER
2
STRIPE
2
STRIPE
2
STRIPE; 85
2
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 89
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
4.
PAYMENT TERMS
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and the
carrier.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.
Parts must be in new and resalable
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
6.
The following items are not returnable:
a.
Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b.
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c.
Any line item with an extended dealer
net price of less than $5.00.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $20.00 to $50.00 surcharge will be added to
the invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
d.
Special order items.
RETURNED GOODS POLICY
e.
Electrical components.
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, and lubricants.
LIMITATIONS OF SELLER’S LIABILITY
g.
Decals and paper products.
1.
h.
Items purchased in kits.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
a.
b.
The list must be typed or computer
generated.
c.
The list must state the reason(s) for
the return.
d.
The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.
3.
The parts numbers and descriptions
must match the current parts price
list.
The list must include the name and
phone number of the person
requesting the RMA.
A copy of the Return Material
Authorization must accompany the return
shipment.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within 5 days, the material will be returned
to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
LIMITATION OF WARRANTIES
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. A part
from such written statement of warranty, there
are no warranties, express, implied or statutory,
which extend beyond the description of the
products on the face hereof.
PAGE 90 — DCA-85SSJU — PARTS AND OPERATION MANUAL — REV. #2 (12/21/01)
NOTE PAGE
DCA-85SSJU — PARTS AND OPERATION MANUAL— REV. #2 (12/21/01) — PAGE 91
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
Manufactured for Multiquip Inc.
by
DENYO MANUFACTURING CO., USA
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX: 310-537-3927
E-MAIL: [email protected]
WWW: multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement