AdvAnced OperAtiOn Groups

AdvAnced OperAtiOn Groups
Advanced Operation
Groups
Use a Miro Wireless Plug-In Lamp Module in conjunction with MRD8 Wireless
Multilocation Controllers to control one plug-in lamp outlet from multiple
locations. Binding the lamp module and MRD8 devices together in the same
Group lets you operate the lamp module from any of the control locations.
You can include other Miro wireless devices in the Group. All devices in the
Group operate when one member operates. If, for example, you increase the
brightness on one device in the Group, all devices will increase brightness.
Set the House ID (see Set House ID) before setting up Groups.
1. Go to any device that you want to include in the Group. Press . The device
LED flashes yellow, and all other devices in the House flash green. You now
have 5 minutes to complete this process.
2. To include or exclude a device in the Group press on the device until the
LED changes color. Yellow flashing LED = Included in the Group
Green flashing LED = NOT included in the Group
If you get to a device and it is NOT flashing, the 5 minute binding process
timer may have expired. Go back to step 1 and repeat.
3. Return to the device used in step 1 and press to terminate Group binding.
All LEDs revert to solid green. Now, all the devices in the Group control their
load circuit in exactly the same manner.
Adding a Module to a Group in an Existing System
1. Go to a device that is in the Group where you want to add the module.
Press . The device LED and all members of the Group flash yellow. The
new module flashes green.
2. Press on the new module until its LED flashes yellow.
3. Return to the device used in step 1 and press . All LEDs are solid green.
Deleting a Module from a Group in an Existing System
1. Go to a device other than the one you’re deleting that is in the existing
Group. Press until the LED flashes yellow on each member of the Group .
2. Press on the module you want to remove, until its LED flashes green.
3. Return to the device used in step 1 and press . All LEDs turn solid green.
Scene Control
The Miro wireless plug-in lamp module may be easily incorporated into room
and whole house preset scenes. The Miro Installation Guide provides more
information about configuring scenes and presets.
Instructions for installation and use are included with the relevant Miro
wireless room and whole house control devices. Application support
information and the Miro Installation Guide is available online.
Cleaning
Clean using only a cloth dampened with water and a little mild detergent.
Use of solvents or hydrocarbon-based cleaners may cause permanent damage.
Troubleshooting
During Set House ID, the LED is not flashing on some wireless Miro
devices.
• If LED is solid green before initiating house ID binding:
The device already has another house ID. Reset it to the factory default so
that it can be bound to the desired house ID. Resetting to factory defaults is
described in the “I need to start over” issue.
• If LED is solid yellow after initiating house ID binding:
The device may be out of range of the initiating device. Add a MRR2 Miro
Wireless Repeater to boost signal range.
I made a configuration mistake. I need to start over.
You can reset any Miro wireless device to factory default settings by pressing
and holding until the LED changes to solid yellow (approximately 10
seconds). During the process, the LED flashes yellow and when complete, it
changes to solid yellow. The device can then be reconfigured, exactly like any
new device (see the Set House ID section).
The dimmer does not work and the status LED is flashing red
• at 2Hz (10 times in 5 seconds):
The module has detected an overload condition and has shut down.
To clear the fault condition, tap
and wait for the LED to turn green.
Disconnect loads in excess of rated load and try again.
• at 3Hz (15 times in 5 seconds):
The module has detected a short-circuit condition and has shut down.
To clear the fault condition, tap and wait for the LED to turn green.
Remove power, rectify the short-circuit condition, restore power, and try
again.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
The manufacturer could void your authority to operate this equipment.
Warranty Information
Manufacturer warranties its products to be free of defects in materials and
workmanship for a period of five (5) years. There are no obligations or liabilities
on the part of manufacturer for consequential damages arising out of, or
in connection with, the use or performance of this product or other indirect
damages with respect to loss of property, revenue or profit, or cost of removal,
installation or reinstallation.
Legrand Customers contact:Vantage Customers contact:
Please
Recycle
301 Fulling Mill Road Suite G
Middletown, PA 17057
Phone: 800.321.2343
www.legrand.us/onq
03884r2
9/2007
IS-0513
1061 South 800 East
Orem, UT 84097
Phone: 800.555.9891
www.vantagecontrols.com
Wireless Plug-In Lamp Module
Specifications
Operating Voltage................................................. 120VAC, 60Hz
Maximum Load Rating...................................................... 300W
Minimum Load Required.................................................... 25W
Load Type Compatibility...............................................25-300W
Incandescent & quartz halogen lamps
Dimmable electronic or magnetic low voltage transformers
Dimmable cold cathode and neon ballasts
Dimmable 2-wire fluorescent (Advance Mark X or
equivalent) and compact fluorescent ballasts
U.S. Patent 6,175,220
Other utility, design, and foreign
patents pending.
Installation Instructions
MRP6
UNIT DESCRIPTION
The Miro™ MRP6 Wireless Plug-In Lamp module provides
convenient dimming control for most floor and table lamps.
This simple plug-in module makes it easy to include freestanding plug-in lamps in the Miro lighting control system.
Lamp Module
Identification Icon
Miro wireless devices use radio signals to communicate
with each other to control lighting and other types of electric loads in selected
areas. Miro wireless devices use the 900MHz band for high-speed control
communication. Using the “frequency-agile” Top Dog™ technology, Miro wireless
devices avoid interference with other 900MHz devices, such as cordless phones
and baby monitors.
Plug-In
When the lamp has been turned off by the Miro wirless lamp module,
you can
Lamp
Auto-on Operation
still manually turn on the lamp using the lamp’s integral switch. The Miro lamp
module senses the switch opening and closing and immediately applies power to
the load.
Load Types
Use the MRP6 Wireless Plug-in Lamp Module with floor and table lamps of the
following load types (25-300W at 120V):
• Incandescent and quartz halogen lamps
• Dimmable electronic or magnetic low voltage transformers (max load 250W)
• Dimmable cold cathode, neon ballasts (max load 250W)
• Dimmable 2-wire fluorescent and compact fluorescent lamps
CAUTION
CAUTION
To reduce the risk of
overheating and possible
damage to other equipment,
do not install to control a
motor-operated appliance, or
a fluorescent lighting fixture.
Afin de réduire le risque de
surchauffe et la possibilité
d’endommager d’autres
matériels, ne pas installer
pour commander un
appareil à moteur, ou une
lampe fluorescente.
Do not mix different load types on the same plug-in lamp module.
Do not use with diode equipped (some types of energy saving) lamps.
Do not use with flourescent fixtures other than those listed.
Do not use for light fixtures with integral dimmers.
Do not use for motors.
Installation
1. Plug the Miro wireless lamp module into a convenient 15amp 120V grounded
receptacle.
2. Plug the lamp into the grounded 15amp outlet on the base of the lamp
module.
3. Check that the lamp is switched on by pressing the button on the lamp
module. If the light does not come on, put its switch in the on position, and
leave it there. If it still doesn’t come on, check the lamp.
INSTALL IN COMPLIANCE WITH ALL APPLICABLE CODES &
STANDARDS. Failure to follow these instructions may cause
personal injury or equipment damage.
Plug-in Lamp
Module
Lamp
Set House ID
All Miro wireless devices installed in the same home must acquire the same
unique House ID before use. This process is known as house binding. Each Miro
wireless device is bound to all other Miro wireless devices in the house.
New Installation
1. With all devices installed and
energized, make sure that
When you see
every Miro wireless device
in the instructions,
LED is yellow. If any LED
firmly press and
is off, be sure the circuit
hold both the up
breaker is on and the device
is correctly installed.
and down arrow
buttons until the
2. Press on any device paddle
or the up and down arrows
LED changes
on a Miro wireless plug-in
(about 2 seconds).
module until the LED flashes
yellow (about 2 seconds). This
indicates that it has acquired
a unique House ID.
3. Make sure that all other Miro wireless device LEDs are flashing green,
indicating that they have acquired the same House ID.
4. Return to the device used in step 2, which is still flashing yellow.
Press until the LED changes to solid green (about 2 seconds). All device
LEDs in the House change to solid green, indicating house binding is complete.
Adding a Device to an Existing Installation
If you’re adding or replacing a device in a Miro wireless installation that is already
operating, the new device must acquire the same House ID as the other Miro
wireless devices in the house. After the new device is powered up, the LED should
be solid yellow. This indicates that it has not yet acquired a House ID. To acquire
the House ID for the existing system:
1. Press on any previously bound device until its LED flashes yellow (about 2
seconds).
2. Verify that the newly added device LED is flashing green, indicating that it has
acquired the House ID.
3. Return to the same previously bound device used in step 1 and press until
the LED changes to solid green (about 2 seconds). All device LEDs should now
be solid green.
OPERATION
–
–
–
–
Tap once
Fade the load to its last-used level
Tap twice
Full bright
Press and hold
Tap once
Press and hold
Increase the present level
Fade the load to OFF
Decrease the present level
When you
see in the
instructions,
touch the up
arrow button as
directed.
When you
see in the
instructions,
touch the down
arrow button
as directed.
The module may feel warm to the touch during normal operation.
Replacing Lamps
When a lamp must be replaced, unplug the lamp from the MRP6 to provide Air
Gap Isolation for safety.
Power Fail Memory
After a power failure, all Miro devices automatically return to the state that they
were in immediately prior to loss of power. All configuration and scene control
information is preserved.
REVDESCRIPTIONINT:REV. DATE
1
ECO# C00888
MJS
2
EC0# C02412
DR
APPROVED
4/23/04
CG
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
• Print: 2-sides
• Ink Color: Black
• Paper: White 16lb (60g/m sq)
Uncoated, prefer recycled stock
• Final trim size: 16” (Wide) x 6” (High).
• Four (4) fold.
• Final folded size: 4” (Wide) x 6” (High).
4-FOLD
IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Mary Jo Sowinski.
Phone: 408-486-7511
Email: maryjo.sowinski@wattstopper.com
All information in this drawing is the property of Watt Stopper/Legrand and cannot be copied or
used without the written approval of Watt Stopper/Legrand.
Drawn by
REVEL
PLM
SANTA CLARA, CALIFORNIA
MarCom
Engineering
Title: MRP6 Installation Instructions
QA
TITLE BOX PG Scale: 1:1
Drawing #:
03884
Orig. Drawing Date: 23 APR 04
Revision Date: 28 SEP 07
Rev. #:
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising