Craftsman | 315.115460 | Operator`s manual | Craftsman 315.115460 Operator`s manual

PERATOR'S
MANUAL
T$
®
14.4 VOLT IMPACT DRIVER
VARIABLE SPEED/REVERSIBLE
Model No.
315.115460
A
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck
and Co., 3333 Beverly Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
C
983000-986
5-22-06 (REV:01)
Save this manual
for future
reference
[] Warranty ..........................................................................................................................................................................
2
[] Introduction .....................................................................................................................................................................
2
[] General Safety Rules ....................................................................................................................................................
3-4
[] Specific Safety Rules .......................................................................................................................................................
4
[] Safety Rules for Charger .................................................................................................................................................
5
[] Symbols ........................................................................................................................................................................
6-7
[] Features ........................................................................................................................................................................
8-9
[] Assembly .........................................................................................................................................................................
9
[] Operation ..................................................................................................................................................................
10-14
[] Maintenance ..................................................................................................................................................................
15
[] Exploded View and Parts List ........................................................................................................................................
16
[] Parts Ordering/Service
....................................................................................................................................
ONE-YEAR FULL WARRANTY
ON CRAFTSMAN
Back Page
TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN IT TO ANY
SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR
FREE REPAIR (or replacement
if repair proves impossible).
If this Craftsman tool is used for commercial
purchase.
or rental purposes, this warranty applies for only 90 days from the date of
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
This tool has many features for making its use more pleasant and enjoyable. Safety, performance,
have been given top priority in the design of this product making it easy to maintain and operate.
A
and dependability
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
A
WARNING!
Read all instructions.
Failure to
follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term
"power tool" in all of the warnings listed below
refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
SAVE THESE
INSTRUCTIONS
WORK
SAFETY
AREA
[] Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
[] Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL
SAFETY
[] Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
[] Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
[] Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk
of electric shock.
[] Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
[] When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
[] Use battery
MODEL
315.115460
PERSONAL
only with charger listed.
BATTERY PACK
130238005
(Item No. 911 044)
CHARGER
1425301
(Item No. 911 041)
SAFETY
[] Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
[] Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
[] Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
[] Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
[] Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
[] Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
[] if devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER
TOOL USE AND CARE
[] Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
[] Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
[] Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments,
changing accessories,
or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
[] Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
[] Maintain power tools. Check for misalignment
or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
[] Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories
and tool bits etc., in
accordance
with these instructions and in the manner
intended for the particular
type of power tool, taking
into account the working conditions
and the work
to be performed.
Use of the power tool for operations
different from those intended could result in a hazardous
situation.
BATTERY
[]
[]
TOOL USE AND
Use power tools only with specifically
designated
battery packs. Use of any other battery packs may create a
risk of injury and fire.
[]
When batten,, pack is not in use, keep it away from
other metal objects like paper clips, coins, keys, nails,
[]
Wear ear protectors
with impact
noise can cause hearing loss.
[]
Hold power tools by insulated gripping surfaces when
performing
an operation
where the cutting tool may
contact
hidden wiring or its own cord. Contact with a
"live" wire will also make exposed metal parts of the tool
"live" and shock the operator.
drills.
Exposure to
[]
Know your power tool Read operator's
manual carefully. Learn its applications
and limitations,
as well as
the specific
potential hazards related to this power
tool Following this rule will reduce the risk of electric
shock, fire, or serious injury.
[]
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses. They
are NOT safety glasses. Following this rule will reduce the
risk of eye injury.
[]
[]
[]
Protect your lungs. Wear a face or dust mask if the
operation
is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection
during extended
periods of operation.
Following
rule will reduce the risk of serious personal injury.
Battery tools do not have to be
trical outlet; therefore, they are
condition.
Be aware of possiMe
using your battery tool or when
Following this rule will reduce the
fire, or serious personal injury.
[]
Do not place battery tools or their batteries
near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Have your power tool serviced by a qualified repair
person using only identical replacement
parts. This will
ensure that the safety of the power tool is maintained.
WARNING!
To reduce the risk of injury, user must
read instruction manual.
[]
When servicing a power tool, use only identical
replacement
parts. Follow instructions in the Mainte=
nance section of this manual. Use of unauthorized parts
or failure to follow Maintenance instructions may create a
risk of shock or injury.
[]
Do not crush, drop or damage battery pack.
use a battery pack or charger that has been
or received a sharp blow. A damaged battery
to explosion. Properly dispose of a dropped or
battery immediately.
[]
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
[]
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of electric
shock.
[]
For best results, your battery tool should be charged
in a location where the temperature
is more than 50°F
but less than 100°F. Do not store outside or in vehicles.
[]
Under extreme usage or temperature
conditions,
bat=
tery leakage may occur. If liquid comes in contact with
your skin, wash immediately with soap and water, then
neutralize with lemon juice or vinegar. If liquid gets
into your eyes, flush them with clean water for at least
10 minutes, then seek immediate medical attention.
Following this rule will reduce the risk of serious personal
injury.
If the power supply cord is damaged,
it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
this
plugged into an elecalways in operating
hazards when not
changing
accessories.
risk of electric shock,
Under abusive conditions,
liquid may be ejected
from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes,
additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
with the charger specified
by the
A charger that is suitable for one type
may create a risk of fire when used with
pack.
[]
[]
[]
CARE
Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
Recharge only
manufacturer.
of battery pack
another battery
screws, or other small metal objects that can make a
connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
[]
Do not
dropped
is subject
damaged
A
WARNING!
READ AND UNDERSTAND ALL
INSTRUCTIONS. Failure to follow all instructions
listed below, may result in electric shock, fire and/or
serious personal injury.
[] Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
CAUTION:
To reduce the risk of electric shock
or damage to the charger and battery, charge
only nickel-cadmium rechargeable batteries as
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
[] Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
[] Use of an attachment not recommended
or sold
by the battery charger manufacturer
may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
[] Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords
immediately.
[] Make sure cord is located so that it will not
be stepped on, tripped over, come in contact
with sharp edges or moving parts or otherwise
subjected to damage or stress. This will reduce the
risk of accidental falls, which could cause injury, and
damage to the cord, which could result in electric
shock.
[] Keep cord and charger from heat to prevent
damage to housing or internal parts.
[] Do not let gasoline, oils, petroleum-based
products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
I
=
2.
3.
PC
SAVE THE
[] An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American Wire Gauge
[] Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
[] Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of
electric shock.
[] Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
[] Risk of electric shock. Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions.
Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
NT SAFETY INSTRUCTION
E IN }TR CTIO
This manual contains important safety and operating instructions for battery charger 1425301.
Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and
product using battery.
CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries
may burst, causing personal injury or damage.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.
Properinterpretation
ofthesesymbolswillallowyouto operatethetoolbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
mz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
[]
Class II Tool
Double-insulated
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields
and, as necessary, a full face shield when operating this
product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
min
O
A
@
@
@
@
of current
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociatedwiththis product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates
imminently
in death oranserious
injury.hazardous situation, which, if not avoided, will result
WARNING:
Indicates
potentially
hazardous situation, which, if not avoided, could result
in death ora serious
injury.
CAUTION:
Indicates
potentially injury.
hazardous situation, which, if not avoided, may result
in minor ora moderate
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
,_blL WARNING:
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest SEARS OR OTHER QUALIFIED SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
_lb,
To avoid serious personal injury, do not
attempt to use this product until you read thoroughly
and understand completely the operator's manual. If
you do not understand the warnings and instructions
in the operator's manual, do not use this product.
Call Sears customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
PRODUCT
SPECiFICATiONS
Coupler ......................................................................
Motor ...............................................................
1/4 in.
14.4 Volt DC
Gear Train ..........................................................
One Speed
Torque ...................................................................
Switch .............................. VSR (Variable Speed Reversible)
Charger Input ...................................
No Load Speed .................................
Charge Rate .............................................................
0-2,500 r/rain. (RPM)
Blows Per Minute ..........................................
850 in.lb.
120 V, 60 Hz, AC only
1 Hour
0-3,500 BPM
BUILT-INCOUPLER
1/4 in. SOCKET
ADAPTER
LED
SWITCH
TRIGGER
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE/
CENTERLOCK)
MAGNETIC
BIT HOLDER
SCREWDRIVER
BITS
STORAGE
BATTERYPACK
CHARGER
Fig. 1
KNOWYOUR IMPACTDRIVER
DIRECTION
See Figure 1.
(FORWARD/REVERSE/CENTER
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all
operating features and safety rules.
Your tool has a direction of rotation (forward/reverse/
center lock) selector located above the switch trigger for
changing the direction of bit rotation. Setting the switch
trigger in the OFF (center lock) position helps reduce the
possibility of accidental starting when not in use.
BIT STORAGE
LED WORKLIGHT
Bits provided with the tool can be placed in the storage
area, located on the base of the tool.
The LED worklight, located on the front of the tool, illuminates when the switch trigger is depressed. This provides
extra light for increased visibility.
BLOWS
PER MINUTE
This tool features an impact speed of 0-3,500 blows per
minute (BPM). Blows per minute is the number of impacts
per minute.
CHARGER
The charger has a key-hole hanging feature for convenient, space-saving storage. Screws should be installed
so that the center distance is 4-1/2 in.
COUPLER
MAGNETIC
OF ROTATION
SELECTOR
LOCK}
BIT HOLDER
The magnetic bit holder extends the reach of the impact
driver bit and holds the bit and screws until you are ready
to drive them.
VARIABLE
SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
Quickly and easily change bits without the need for tools.
UNPACKING
A
This product has been shipped completely assembled.
[] Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list
are included.
[] Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
A
[] Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
PACKING
LIST
impact Driver
Standard Bits (2)
Magnetic Bit Holder
1/4 in. Socket Adaptor
Charger
Battery (2)
Carrying Case
Operator's Manual
WARNING:
If any parts are damaged or missing
do not operate this tool until the parts are replaced.
Failure to heed this warning could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
A
WARNING:
To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the tool when assembling
parts.
A
A
A
CHARGING
WARNING:
Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
[] Charge the battery pack only with the charger provided.
[] Make sure the power supply is normal household
voltage, 120 vo(ts, 60 Hz, AC only.
[] Connect the charger to the power supply.
[] Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger. See
Figure 2.
APPLICATIONS
[] Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
You may use this tool for the purposes listed below:
[] Driving long deck screws while building a deck
[] Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
[] Driving carriage bolts into deck posts
[] Driving Tapcon screws into block walls and concrete
[] Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
[] Driving screws into metal studs
[] Driving nuts and bolts using an impact socket
CAUTION:
If at any point during the charging
process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the
product. DO NOT insert another battery. Return the
charger and battery to your nearest Sears or other
qualified service center for service or replacement.
CHARGER
NOTE: The green LED will remain on until the battery
pack is removed from the charger or charger is
disconnected from the power supply.
[] If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack. Allow
the battery pack to remain in the charger for 15 to 30
minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the red
LED does not come on after 30 minutes, this may
indicate a defective battery pack that should be
replaced.
OF CHARGER
BE ON TO INDICATE
AND BATTERY
STATUS
PACK
NOTE: If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and charger to your nearest Sears or other qualified service center for
electrical check.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of
this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
LED WILL
BATTERY
If battery pack is below normal temperature range, the green
LED on charger will come on. Allow battery pack to reach
normal temperature, then the red LED will come on.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
LED FUNCTIONS
A COOL
OF
PACK:
[] Red LED on = Fast charging mode.
BATTERYPACKIN
CHARGER
[] Green LED on = Fully charged and in maintenance
charge mode.
[] Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of normal temperature range.
[] Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
LEO
[] No LED on = Defective charger or battery pack.
CHARGING
THE BATTERY
Y
PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front of the
charger comes on.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged.
CHARGER
10
GREENLED
Fig. 2
[] Afternormalusage,a minimumof 1 hourofcharging
timeis required
to fullyrecharge
batterypack.
[] Thebatterypackwill becomeslightlywarmto the
touchwhilecharging.Thisis normalanddoesnot
indicatea problem.
[] Donot placethechargerandbatterypackin anarea
of extremeheator cold.Theywillworkbestat normal
roomtemperature.
NOTE:Thechargerandbatterypackshouldbeplaced
ina locationwherethetemperature
is morethan50°F
butlessthan100°R
[] Whenbatteriesbecomefullycharged,unplugthe
chargerfrompowersupplyandremovethebattery
pack.
CHARGING
A HOT BATTERY
TO INSTALL
BATTERY
PACK
See Figure 3.
[] Lock the switch trigger by placing the direction of rotation selector in the center position.
[] Place battery pack in the tool. Align raised rib on
battery pack with groove inside tool. Make sure the
latches on each side of the battery pack snap into
place and battery pack is secured in tool before beginning operation.
CAUTION: When placing battery pack in the tool,
be sure raised rib on battery pack aligns with the
groove inside tool and latches into place properly.
Improper installation of the battery pack can cause
damage to internal components.
PACK
When using the tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before
attempting to recharge. When the battery pack becomes
discharged and is hot, this will cause the green LED to
come on instead of the red LED. After 30 minutes, reinsert
the battery pack in the charger. If the green LED continues
to remain on, return battery pack to your nearest Sears or
other qualified service center for checking or replacing.
NOTE: This situation only occurs when continuous use
of the tool causes the batteries to become hot. It does
not occur under normal circumstances. Refer to CHARGiNG A COOL BATTERY PACK for normal recharging
of batteries. If the charger does not charge your battery
pack under normal circumstances, return both the battery
pack and charger to your nearest Sears or other qualified
service center for electrical check.
LATCHES
DEPRESSLATCHESTO
RELEASEBATTERYPACK
TO REMOVE
See Figure 3.
BATTERY
Fig. 3
PACK
[] Lock switch trigger on the tool by placing the direction
of rotation selector in center position.
[] Locate latches on end of battery pack and depress to
release battery pack from the tool.
[] Remove battery pack from the tool.
11
A
A
CAUTION: To prevent gear damage, always allow
the coupler to come to a complete stop before
changing the direction of rotation.
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
To stop the impact driver, release the switch trigger and
allow the coupler to come to a complete stop.
CAUTION: The metal surface may become hot during use. Avoid contact with it to avoid possible burn
injury.
SWITCH
NOTE: The impact driver will not run unless the direction
of rotation selector is pushed fully to the left or right.
BUILT-IN COUPLER
See Figure 5.
TRIGGER
See Figure 4.
The tool has a built-in coupler. The coupler has been
designed to accept 1/4 in. hex bits.
To turn the tool ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE
SPEED
See Figure 4.
COUPLER
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a normal part of the switch function.
Fig. 5
LED WORKMGHT
See Figure 6.
The LED worklight, located below the coupler, illuminates
when the switch trigger is depressed. This provides additional lighting on the surface of the workpiece for operation in lower-light areas.
FORWARD
\
SWITCH
TRIGGER
DIRECTION
OF ROTATION
(FORWARD/REVERSE/CENTER
See Figure 4.
Fig. 4
SELECTOR
LOCK)
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With
the impact driver held in normal operating position, the
direction of rotation selector should be positioned to the
left of the switch trigger for driving. The driving direction
is reversed when the selector is to the right of the switch
trigger.
LED
WORKLIGHT
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when not
in use.
12
Fig. 6
BIT STORAGE
REMOVING
See Figure 7.
See Figure 8.
When not in use, bits provided with the tool can be placed
in the storage area located at the bottom of the tool
handle.
[] Lock switch trigger on the tool by placing the direction
of rotation selector in center position.
BITS
[] Pull the coupler forward and hold in position.
[] Pull bit straight out of coupler.
_,_
SCREWDRIVER
S
BiTS
INSTALLING
THE MAGNETIC
BIT HOLDER
DRILL BIT OR SOCKET ADAPTOR
AND
See Figure 9,
[] Lock the switch trigger by placing the direction of rotation selector in the center position.
[] Pull the coupler forward and hold in position.
[] Insert magnetic bit holder straight into coupler as
shown.
[] Slide the coupler back slowly and release.
INSTALLING
[] Insert drill bit or socket adaptor straight into bit holder
as shown.
Fig. 7
BiTSTORAGE AREA
RELEASE
BITS
See Figure 8.
PULLCOUPLER
FORWARD
[] Lock switch trigger on the tool by placing the direction
of rotation selector in center position.
MAGNETIC
BiTHOLDER
[] Pull the coupler forward and hold in position.
[] Insert bit straight into coupler.
[] Slide the coupler back slowly and release.
RELEASE
COUPLER
PULLCOUPLER
FORWARD
BiT
1/4 in.SOCKET
ADAPTOR
SERT BiT
REMOVING
THE MAGNETIC
BIT HOLDER
DRILL BIT OR SOCKET ADAPTOR
Fig. 9
AND
See Figure 9.
[] Lock the switch trigger by placing the direction of rotation selector in the center position.
/
LOCKING GROOVE
COUPLER
[] Pull drill bit or socket adaptor straight out of bit holder.
Fig. 8
[] Pull the coupler forward and hold in position.
[] Pull magnetic bit holder straight out of coupler.
13
DRIVINGOR REMOVINGSCREWS
See Figures 10- 11.
[] Place the direction of rotation selector in the correct
position for the operation.
0
[] Hold the impact driver with one hand.
[] Place the bit on the screw head and slowly depress the
switch trigger. Start the bit slowly for more control.
[] As screw is driven, impacting will begin.
_JIL WARNING:
0
Do not drive a screw where there is
likely to be hidden wiring behind the surface. Contact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator. If you must
drive a screw where hidden wire may be present,
always hold tool by insulated gripping surfaces
(handle) when performing the operation to prevent a
shock to the operator, as seen in figure 10.
0
0
_
RIGHT
Fig. 10
WRONG
14
Fig. 11
A
A
A
GENERAL
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean tools. If the operation is dusty, also wear a
dust mask.
_
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
WARNING:
To avoid serious personal injury, always
remove the battery pack from the tool when cleaning
or performing any maintenance.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
BATTERIES
BATTERY
The battery pack for this tool is equipped with nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing.
FOR RECYCLING
PACK REMOVAL
;B Rc'c'c'c'_
\
AND PREPARATION
To preserve natural resources, please
recycle or dispose of batteries
properly.
This product contains nickel-cadmium
batteries. Local, state or federal
laws may prohibit disposal of nickelcadmium batteries in ordinary trash.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
_IL
For battery pack storage longer than 30 days:
[] Store battery packs in a "discharged"
Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
[] Remove the battery pack from the charger once it is
fully charged and ready for use.
[] Store the battery pack where the temperature
80°R
WARNING:
is below
condition.
15
CRAFTSMAN
MODEL
_"
l
14.4 VOLT iMPACT DRIVER
NUMBER 315.115460
]
The model
number
will be found
on a plate
the motoror housing.
Always repair
mention
the model
number
in all
correspondence
regarding
yourattached
IMPACTto DRIVER
when ordering
parts.
SEE BACK
PAGE FOR PARTS ORDERING
1
INSTRUCTIONS
3
4
8
PARTS
Key
No.
LIST
Part
Number
Description
130238005
Battery Pack (Item No. 911044) ......................................................................
1
2
1425301
Charger (Item No. 9_11041) ..............................................................................
1
3
940237081
Data Label .......................................................................................................
1
4
940203051
Logo Label ......................................................................................................
1
5
670283004
Magnetic Bit Holder ........................................................................................
1
6
690884003
Socket Adaptor ...............................................................................................
1
7
70803054
Screwdriver
Bit (#6-8 mm Slotted) ..................................................................
1
8
670802034
Screwdriver
Bit (#2 Philip's Head) ...................................................................
1
300912236
Carrying Case - Not Shown ...........................................................................
983000986
Operator's
1
Qty.
Manual
* Can Be Purchased At Most Sears Stores/Sears.corn/Parts
16
and Service
1
Download PDF

advertising