Cross Technologies | 210-01 CATV | ENGDOC # - SLAC - Stanford University

ENGDOC # - SLAC - Stanford University
ENGDOC#
GENERAL CABLE PLANT NOTES
SLAC
POWER CONVERSION DEPARTMENT
ID-236-801-36-RX2
Release Dated: 25-JAN-87
Last Revision 08/08/2011
SLAC NATIONAL ACCELERATOR LABORATORY
Operated by Stanford University for the U.S. Dept of Energy
Stanford University
Stanford, California
Proprietary data of Stanford University and/or U.S. Department of
Energy. Recipient shall not publish the information within unless
granted specific permission of Stanford University.
GENERAL CABLE PLANT NOTES
POWER CONVERSION DEPARTMENT
ID-236-801-36-RX2
Release Dated: 25-JAN-87
Last Revision 08/08/2011
Introduction
This document explains, and is to be used in conjunction with, a CABLE INSTALLATION SCHEDULE.
The CABLE INSTALLATION SCHEDULE is supplied as another document in the total package of which this document is a part.
Note that this is a general document, and may contain much more information than may be required for the CABLE INSTALLATION SCHEDULE
supplied. This is particularly true of the color code, cable types and cable termination tables which follow.
This document is divided into the following sections:
1.
2.
3.
4.
5.
6.
7.
8.
Introduction
General Notes
Description of the CABLE INSTALLATION SCHEDULE
Table 1 - Color Code Tables (and connection points) for Multi-Conductor Cables
Table 2 - Cable Types and Cable Descriptions
Table 3 - Cable Termination Descriptions
Table 4 - Trim Codes for Coaxial Cable Terminations
Table 5 - Document Revision Notes (for this document)
8/8/2011
2
General Notes
1. Some definitions and descriptions may not be fully defined at the time that this listing was printed. Any such known areas will be noted by a
sequence of 2 or more X's (i.e. 'termination type LFB-XX' or 'tooling XX-XXX'). Any such missing information will be completed as later listings
are printed. Additional (and missing) information will also be included in later revisions, as that information is given to the keeper of this document.
Note: where information is missing, PLEASE ASK QUESTIONS. Where such information is added, it will be so specifically listed in the revision
notes section (last pages) of all subsequent listings.
2. Block diagrams and other informational drawings have been supplied as a part of the total package. Those drawings are also to be used as
references to aid in the understanding of the CABLE INSTALLATION SCHEDULE, and this document.
3. A large number of short and medium length cables will be furnished already cut and terminated, ready for final connection by the subcontractor.
4. All long-haul cables are to be cut and generally terminated by the subcontractor. For details refer to the specific cable-end assembly instructions,
and the other drawings and documents supplied with the total package.
5. The cable installation schedules list the exact location (+/- 2 feet, sufficient to resolve any ambiguities) of the components to which each end of
any given cable is to be connected. Station marks will be stenciled on the wall at 50 feet intervals in collider housings, and may be indicated by
drawings for off-line components. Additional information on these station locations is given in the section entitled 'Cable Installation Schedule
Format Description' below.
The subcontractor shall refer to these station marks as may be required in order to locate all components.
8/8/2011
3
6. GENERAL TERMINATION NOTE: FOR MULTIPLE POINT TERMINAL BLOCKS;
Terminal blocks are normally 50 point blocks. Each termination point has four flags -- A, B, C and D. Unless otherwise specifically noted, connect
the indicated wire to flag 'C'.
The Cable Installation Schedule indicates the terminal block point numbers to be connected. The point numbers are called out at the right end of the
'ORIGIN' or 'DESTINATION' information field. For instance, -01/50, -26B50, -08C, etc., means to connect to points 1 through 50, the 'B' flag of
points 26 through 50, and the 'C' flag of point 8, respectively. The points are wired in increasing numerical sequence, always starting with the first
wire of the cable, per the indicated color code, to the lowest indicated number point. For the example given for 26B50, the first wire goes to point
26B, the second wire to point 27B, etc. If commas separate the numbers (for instance, -41,45B,43), rather than a slash, that means the first wire goes
to point 41C, the second to point 45B and the third to point 43C.
The last two conductors of 52 conductor cables are generally not terminated. Also, some other cables are only partially wired. In all cases fold back
and tape any unused conductors.
7. Termination Tooling.
It is IMPERATIVE that the correct tooling be used for:
a. trimming coaxial and other special cable for termination, and
b. for crimping, or other assembly, of any termination to any wire or coax.
Much of the required tooling is specified further on in this specification. Should any required tooling not be specified, or if it is desired to use any
tooling other than that explicitly specified, such tooling REQUIRES THE PRIOR APPROVAL OF THE DESIGNATED SLAC INSPECTOR.
Any use of unspecified or non-approved tooling MAY REQUIRE THE REWORK OR REPLACEMENT OF THOSE CABLES AND/OR
TERMINATIONS.
8. Cables not rated as tray cables or as Halogen Free Low Smoke must have the approval of the Electrical Safety Officer (ESO) or the Electrical
Safety Committee (ESC) prior to requests for installation. Requests for installation should specify any additional steps required; I.E additional
support or fire blocking.
8/8/2011
4
Cable Installation Schedule Format Description
The following is a description of the CABLE INSTALLATION SCHEDULE format:
FORMAL DEVICE NAME: This is the SLAC/SLC formal name for the system of which the indicated cable is a component. It is listed herein in
order to allow quick reference to the actual control, readout, or other system as questions may occur. Example: QUAD:PI00,5920.
CABLE FUNCTION: This column gives a brief description of the function of the cable.
CABLE TYPE: This column gives the standard designation or an abbreviated form of it. Refer to TABLE 2 for the full and detailed description of
any given cable.
CABLE NUMBER This column lists the cable identification number, a number that is unique to a single cable installed at SLAC. This number must
be affixed to each end of each cable. Pre-assembled cables will normally be provided with the correct cable numbers attached. Other labels will be
provided to the subcontractor for attachment at the time of cable installation.
ORIGIN / LOCATION: This column refers to the location of the cable's origin. The distinction between 'ORIGIN' and 'DESTINATION' is of
particular importance when installing pre-assembled cables, in that any excess cable, over that needed for a service loop at the 'ORIGIN' end, is to be
stored/distributed at the 'DESTINATION' end of the installed cable. Most cables originate at one of the instrument racks in a support building or
collider housing alcove. For instance;
B136-1714-J10/J13 is to be interpreted as follows:
B136 indicates Building 136 17 indicates rack 17, chassis elevation 14(location in the rack) J10/J13 indicates JACK NOS. 10 through
13 on the chassis.
Occasionally, after the chassis elevation and jack (terminal board, etc.), additional digits will appear. They will be explained in
TABLE 3 under the cable termination description, or a separate wire list will be furnished.
Similarly AS15-04-0132-TB1-1B25 is to be interpreted as follows;
AS15 indicates Arc South, in the area of Achromat 15 (which spans about 170 feet) 04 indicates Alcove 4 (in the South Arc), 0132
indicates rack 01, elevation 32, (rack 01 is the first (leftmost facing the rack fronts) rack. TB1 indicates TERMINAL BLOCK NO. 1
1B25 indicates POINTS 1 through 25. The 'B' indicates that this is a FASTON terminal block, and means wire to the 'B' flags only,
and in the same sequence as the color code for that wire type. See the tables in Section 3 for the color codes.
8/8/2011
5
Note that the first characters of this field (to the first '-') will take a form similar to one of the following:
1.
2.
3.
4.
5.
6.
7.
8.
B(nnn), indicating a Building number
KAnn, indicating an Alcove in the Klystron Gallery area, where (nn) is the sector number
KFnn, indicating a Fiat in the Klystron Gallery area, where (nn) is the sector number
KGnn, indicating a Klystron Gallery area, where (nn) is the sector number
KMnn, indicating a Mechanical Alcove in the Klystron Gallery area, where (nn) is the sector number
LInn, indicating a LInac housing area, again where (nn) is the sector number
DKG, indicating a Damping ring device in sector 01 of the Klystron Gallery
N or S, followed by DRV, DR, RTL or LTR. This indicates a North or South Damping ring area, as follows:
DRV indicates that the location is on the wall or floor of the Damping Ring Vault, but NOT on a ring girder.
DR indicates a location actually on a Damping Ring girder
LTR is in the Linac-To-Ring (east) housing, and
RTL is in the Ring-To-Linac (west) housing.
Where LTR or RTL is followed by an S(n), the 'S' means that the location is on the wall or floor within that Section of the indicated
housing.
Where LTR or RTL is followed by an (nn), the location is actually on a girder in the indicated housing, and the (nn) is the girder
number.
1. BSY indicates a location in the BEAM-SWITCHYARD (BSY) area.
2. AN(nn) or AS(nn), indicating a location in the main Collider Arcs (North or South), the (nn) is the number of the Magnet Achromat (about
170 foot in length) spanning and/or including the exact location.
If (nn) is '00', the location is prior to the first Achromat, in the launch portion of the indicated Arc, but actually inside the BSY housing area.
If (nn) is '24' or '25', the locations are in the Final Focus area of the indicated tunnel. (The last 32 feet of '25' on each side are actually in the Collider
Pit.)
•
Additional information on the details for this field may be found in 'Data Entry Definitions for the SLC Cable Plant Program' (SLAC
ELDDOC #83).
STATION: The exact location of a Beam Line related item is identified on the CABLE INSTALLATION SCHEDULE as a station number shown in
feet, plus or minus 2 feet.
8/8/2011
6
DESTINATION / LOCATION: This column is similar to 'ORIGIN' above, although many cables may find their destinations at a connection box or
machine component on the actual Beam Line. Connection boxes and machine components are generally identified by the geographic area together
with an abbreviated generic name. These components generally will be labeled, when they are in place at the time of the cable installation.
Identification labels will probably not be found for devices not installed, and the LOCATION stations will be required to locate the given (future)
connection point.
INSTALLATION NOTES: (Two entries, one each for ORIGIN and DESTINATION.)
1. The first field (left character in the field) is a code which indicates when, and by whom, the indicated end of a cable is terminated and connected.
Each end of a cable is given an assembly code, and each end may require entirely different treatment.
This code is specifically decoded for the subcontractor on the second line of this field (see 'c.' below). The codes used are as follows:
•
'0': No action to be taken by the subcontractor. This cable either exists, or is to be installed at a later time. It is listed for completeness of the
CABLE INSTALLATION SCHEDULE, and especially to show the full sequence of a set of cables.
•
'1': A cable with a pre-terminated end (an assembly) is delivered to the subcontractor. The subcontractor is to install the cable. The device
connection is to be done later by others.
•
'2': This cable has been previously installed, the subcontractor is only to terminate as indicated. Connection will be done later, by others.
•
'3': The subcontractor is to install and terminate only. Connection is to be done later, by others.
•
'4': The subcontractor is to make the indicated connections, the cable has been previously installed and terminated.
•
'5': A cable with a pre-terminated end (an assembly) is delivered to the subcontractor. The subcontractor is to connect this end to the indicated
device following cable installation.
•
'6': The subcontractor is to terminate and connect only. The cable has been previously installed.
•
'7': The subcontractor is to install, terminate and connect this end.
•
'8': This end of the cable is terminated and partially installed. The subcontractor shall finish the cable installation and connect this end to the
indicated device.
•
'9': The cable is partially installed. The subcontractor shall finish the cable installation, terminate, and connect this end to the indicated device.
8/8/2011
7
•
'10': The cable is partially installed. The subcontractor shall finish the cable installation to the indicated device. Others will do the termination
and connection later.
•
'11': The cable is partially installed. The subcontractor shall finish the cable installation, and termination. Others will do the connection later.
•
'M': Commercially prefabricated (not built by SLAC or to a SLAC specification) I.E. a 6' AC power cord with molded ends.
•
'P': Commercially prefabricated (not built by SLAC or to a SLAC specification) I.E. a ribbon cable with non-molded connectors.
•
'S': Special termination and connection, to be done later, by others. The subcontractor is to only install the cable.
•
'SS': Termination and connection to be done later by others. The subcontractor to only install the cable. Any excess length at this end of the
cable shall be neatly coiled as indicated in the subcontract's drawings and specifications.
TERMINATION:
a. This field is the code for the connector or termination hardware to be used. This information is always given, even if not directly needed by
the subcontractor. See TABLE 3 for cable termination details and refer to TABLE 2 for a cable description and to TABLE1 in Section 3, as
necessary, for the color code for that cable.
b. The second line of this field contains the code letters instructing the subcontractor on exactly what is to be done. If the second line is blank
(see code '0' above), no action is to be taken by the subcontractor. Otherwise, any single code, or multiple combination of the codes, may
occur.
LENGTH: This column gives the estimated cable length in feet. The exact length may be verified in the field. For some special cables, the
indicated length is the delay time of the cable, in nanoseconds. Timing is indicated as a decimal number, ie. Length = '176' is 176 feet, Length
= '176.0' is a delay time of 176.0 nanoseconds.
ROUTING SEQUENCE: This column refers to the routing of the cable in the raceway system. Refer to the tray layout drawings and key
plans for details.
REV #: This column indicates the change level for the indicated cable ONLY. Blank indicates no change since original entry, '1' indicates one
change, etc.
8/8/2011
8
TABLE 1 - COLOR CODE TABLES
(and connection points) for Multi-Conductor Cables.
The following tables are necessary or useful to complete the cable and connector descriptions given in this document.
TABLE 1 - ABBREVIATIONS USED FOR COLORS.
COLOR
2-PLACE
3-PLACE
CLEAR
CL
CLR
BLACK
BK
BLK
BROWN
BN
BRN
RED
RD
RED
ORANGE
OR
ORN
YELLOW
YE
YEL
GREEN
GN
GRN
BLUE
BU
BLU
VIOLET
VI
VIO
GREY
GY
GRY
WHITE
WT
WHT
PINK
PK
PNK
TAN
TN
TAN
3-place color designations are normally used, 2-place are listed for clarity in case they are used in any additional
information.
The following is common information, which is used in the wire tables which follow:
a. * -- a pin designation letter preceded by a '*' (i.e. '*C') indicates that this letter is lower case letter (pin) on
the connector.
b. ** -- where more than one color is given for a wire (i.e. ' WHT/RED/BLK') the first color is the base color of the
insulation, The additional colors are the tracer (striping) colors.
8/8/2011
9
TABLE 1 - COLOR CODE 1A (NEMA PUB. NO. WC 30, TABLE 5-2)
The following standard color sequence can be applied to unpaired and paired cables. An A and B
designation for the two wires in a pair is sometimes useful. A “CABLE TERM. LETTER” is
given for convenience for use with multi-pin connectors that are wired to follow this standard color code
sequence.
Used With CABLE TYPES
4C8/3V
8C16/3V
12C12/3V
12C16/3V
12C22/3V
19C16/3V
26C16/3V
26C22/3V
52C16/3V
4C16T6V
8C16T6V
12C16T6V
26PR22OS
12C18/3V
2C12OS
UNPAIRED
CABLE
COND NO.
**WIRE
COLOR
CODE
PAIRED
CABLE
PAIR
NO.
CABLE
TERM.
LETTER
UNPAIRED
CABLE
COND. NO.
** WIRE COLOR
CODE
PAIRED
CABLE PAIR
NO.
CABLE
TERM.
LETTER
1
BLK
1A
A
27
BLU/BLK/WHT
14A
*D
2
WHT
1B
B
28
BLK/RED/GRN
14B
*E
3
RED
2A
C
29
WHT/RED/GRN
15A
*F
4
GRN
2B
D
30
RED/BLK/GRN
15B
*G
5
ORN
3A
E
31
GRN/BLK/ORN
16A
*H
6
BLU
3B
F
32
ORN/BLK/GRN
16B
*I
7
WHT/BLK
4A
G
33
BLU/WHT/ORN
17A
*J
8
RED/BLK
4B
H
34
BLK/WHT/ORN
17B
*K
9
GRN/BLK
5A
J
35
WHT/RED/ORN
18A
*M
10
ORN/BLK
5B
K
36
ORN/WHT/BLU
18B
*N
11
BLU/BLK
6A
L
37
WHT/RED/BLU
19A
*P
8/8/2011
10
12
BLK/WHT
6B
M
38
BLK/WHT/GRN
19B
*Q
13
RED/WHT
7A
N
39
WHT/BLK/GRN
20A
*R
14
GRN/WHT
7B
P
40
RED/WHT/GRN
20B
*S
15
BLU/WHT
8A
R
41
GRN/WHT/BLU
21A
*T
16
BLK/RED
8B
S
42
ORN/RED/GRN
21B
17
WHT/RED
9A
T
43
BLU/RED/GRN
22A
18
ORN/RED
9B
U
44
BLK/WHT/BLU
22B
19
BLU/RED
10A
V
45
WHT/BLK/BLU
23A
20
RED/GRN
10B
W
46
RED/WHT/BLU
23B
21
ORN/GRN
11A
X
47
GRN/ORN/RED
24A
22
BLK/WHT/RED
11B
Y
48
ORN/RED/BLU
24B
23
WHT/BLK/RED
12A
Z
49
ORN/RED/BLU
25A
24
RED/BLK/WHT
12B
*A
50
BLK/ORN/RED
25B
25
GRN/BLK/WHT
13A
*B
51
WHT/BLK/ORN
26A
26
ORN/BLK/WHT
13B
*C
52
RED/ORN/BLK
26B
8/8/2011
11
TABLE 1 - COLOR CODE 1B (NEMA PUB. NO. WC 30, TABLE K-2)
The following standard color sequence should be used, instead of 1A, for cables that use yellow and brown
rather than white and green. An A and B designation is given for use with paired cables. A
"CABLE TERM. LETTER" is given for convenience for use with multi-pin connectors that are
wired following this standard color code sequence. When there are more than 36 conductors (18) pairs,
some of the colors will be repeated and repeated. In the latter cases, the lay or position of a wire in the
inner or outer layers must be considered to uniquely identify a conductor.
Used With CABLETYPE
8PR16TS
12PR16TS
16PR16TS
24PR16TS
36PR16TS
50PR16TS
12C12/3V
1PR16OS
UNPAIRED
CABLE
COND NO.
**WIRE
COLOR
CODE
PAIRED
CABLE
PAIR
NO.
CABLE
TERM.
LETTER
UNPAIRED
CABLE
COND. NO.
** WIRE COLOR
CODE
PAIRED
CABLE PAIR
NO.
CABLE
TERM.
LETTER
1
BLK
1A
A
19
ORN/BLU
10A
V
2
RED
1B
B
20
YEL/BLU
10B
W
3
BLU
2A
C
21
BRN/BLU
11A
X
4
ORN
2B
D
22
BLK/ORN
11BA
Y
5
YEL
3A
E
23
RED/ORN
12A
Z
6
BRN
3B
F
24
BLU/ORN
12B
*A
7
RED/BLK
4A
G
25
YEL/ORN
13A
*B
8
BLU/BLK
4B
H
26
BRN/ORN
13B
*C
9
ORN/BLK
5A
J
27
BLK/YEL
14A
*D
10
YEL/BLK
5B
K
28
RED/YEL
14B
*E
11
BRN/BLK
6A
L
29
BLU/YEL
15A
*F
12
BLK/RED
6B
M
30
ORN/YEL
15B
*G
8/8/2011
12
13
BLU/RED
7A
N
31
BRN/YEL
16A
*H
14
ORN/RED
7B
P
32
BLK/BRN
16B
*I
15
YEL/RED
8A
R
33
RED/BRN
17A
*J
16
BRN/RED
8B
S
34
BLU/BRN
17B
*K
17
BLK/BLU
9A
T
35
ORN/BRN
18A
*M
18
RED/BLU
9B
U
36
YEL/BRN
18B
*N
* This letter is lower case on the connector
** The first color is the base color of the insulation.
TABLE 1 - COLOR CODE 1C
The following color sequences can be applied to microphone cable and AC power cords:
Used With CABLE TYPE
2C16OS
2C22MS
3C12TYR
3C16TYR
CABLE
COND NO.
COLOR
CODE
TERM.
LETTER
1
BLK
2
3
8/8/2011
--OR--
CABLE
COND. NO.
COLOR CODE
CABLE
TERM.
LETTER
A
1
BLK
A
WHT
B
2
WHT
B
DRAIN
C
3
GRN
C
13
TABLE 1 - COLOR CODE 1D (BELDEN)
The following standard color sequence can be applied to individually shielded pairs with drain wires.
The "PAIR NO.", designation, 3A,3B and 3C, denotes that, associated with a pair
there are two insulated signal wires 3A and 3B, and one un-insulated drain wire 3C, that makes electrical
contact with the shield for that pair. A "COND. NO." is assigned only for convenience and it
is useful only when each conductor, including the drain, is wired in sequence to a terminal block. Note
that when RED is paired with BLK, the BLK is "PAIR NO." 1B, but when WHT is paired
with BLK, the BLK is "PAIR NO." 2B, etc.
USED WITH CABLE TYPE
3PR20IS
3PR22IS
6PR22IS
12PR22IS
19PR22IS
27PR24IS
6PR24IS
COND. NO
COLOR CODE
PAIR NO.
COND. NO
COLOR CODE
PAIR NO.
COND. NO.
COLOR CODE
PAIR NO.
1
RED
1A
28
BLU
10A
55
BLU
19A
2
BLK
1B
29
RED
10B
56
WHT
19B
3
DRAIN
1C
30
DRAIN
10C
57
DRAIN
19C
4
WHT
2A
31
YEL
11A
58
YEL
20A
5
BLK
2B
32
RED
11B
59
WHT
20B
6
DRAIN
2C
33
DRAIN
11C
60
DRAIN
20C
7
GRN
3A
34
BRN
12A
61
BRN
21A
8
BLK
3B
35
RED
12B
62
WHT
21B
9
DRAIN
3C
36
DRAIN
12C
63
DRAIN
21C
10
BLU
4A
37
ORN
13A
64
ORN
22A
11
BLK
4B
38
RED
13B
65
WHT
22B
12
DRAIN
4C
39
DRAIN
13C
66
DRAIN
22C
8/8/2011
14
13
YEL
5A
40
WHT
14A
67
YEL
23A
14
BLK
5B
41
GRN
14B
68
BLU
23B
15
DRAIN
5C
42
DRAIN
14C
69
DRAIN
23C
16
BRN
6A
43
BLU
15A
70
BRN
24A
17
BLK
6B
44
GRN
15B
71
BLU
24B
18
DRAIN
6C
45
DRAIN
15C
72
DRAIN
24C
19
ORN
7A
46
YEL
16A
73
ORN
25A
20
BLK
7B
47
GRN
16B
74
BLU
25B
21
DRAIN
7C
48
DRAIN
16C
75
DRAIN
25C
22
WHT
8A
49
BRN
17A
76
YEL
26A
23
RED
8B
50
GRN
17B
77
BRN
26B
24
DRAIN
8C
51
DRAIN
17C
78
DRAIN
26C
25
GRN
9A
52
ORN
18A
79
ORN
27A
26
RED
9B
53
GRN
18B
80
BRN
27B
27
DRAIN
9C
54
DRAIN
18C
81
DRAIN
27C
8/8/2011
15
TABLE 1 - COLOR CODE 1E
The following color sequence can be applied to twisted pairs with an overall shield:
Used With CABLE TYPE
3PR22OS
COND.
NO.
COLOR
CODE
PAIR
NO.
TERM.
LETTER
COND.
NO.
COLOR
CODE
PAIR
NO.
TERM.
LETTER
1
BLK
1A
A
5
BRN
3A
E
2
WHT
1B
B
6
WHT
3B
F
3
RED
2A
C
7
DRAIN
OS
G
4
WHT
2B
D
TABLE 1 - COLOR CODE 1F
Used With CABLE TYPE
1PR16AS
4PR16AS
4PR18TC
8PR16AS
16PR16AS
24PR16AS
24PR16TC
27PR22OS
50PR16AS
50PR16TC
The Cable contains twisted pairs. Each pair consists of a white (or red) wire and a black wire.
The white (or red) wire of the pair has a number imprinted on it and is the first or "A"
wire of the pair. The black wire is the "B" wire of the pair. Thus, the white (or red) wires,
in general unless otherwise noted, go in numerical sequence onto the odd number terminal
block flags, and the black wires go onto the even number flags Also, the drain from the overall
shield is not connected unless specifically so instructed.
8/8/2011
16
TABLE 1 - COLOR CODE 1G
The following standard color sequence is to be used for the Magnet Mover cables.
A CABLE TERM LETTER is given for use with the 9-pin connectors used on the
Magnet-Mover cables (connector AMP9S).
Used With CABLE TYPE.
9C18J
UNPAIRED
CABLE.
COND.#
WIRE
COLOR
CODE
CABLE
TERM.
LETTER
1
BLK
A
2
RED
B
3
WHT
C
4
GRN
D
5
ORN
E
6
BLU
F
7
BRN
G
8
YEL
H
9
VIO
J
8/8/2011
17
TABLE 1 - COLOR CODE 1H
Used With CABLE TYPE
5PR20OS
PAIRED
CABLE.
COND.#
***WIRE
COLOR
CODE
PAIRED
WIRE
COND.#
PAIRED
CABLE.
COND.#
***WIRE
COLOR
CODE
PAIRED
WIRE
COND.#
1
WHT/BLK
1A,1B
15
BLK/BLU
15A,15B
2
WHT/BRN
2A,2B
16
BLK/VIO
16A,16B
3
WHT/RED
3A,3B
17
BLK/GRY
17A,17B
4
WHT/ORN
4A,4B
18
BRN/RED
18A,18B
5
WHT/YEL
5A,5B
19
BRN/ORN
19A,19B
6
WHT/GRN
6A,6B
20
BRN/YEL
20A,20B
7
WHT/BLU
7A,7B
21
BRN/GRN
21A,21B
8
WHT/VIO
8A,8B
22
BRN/BLU
22A,22B
9
WHT/GRY
9A,9B
23
BRN/VIO
23A,23B
10
BLK/BRN
10A,10B
24
BRN/GRY
24A,24B
11
BLK/RED
11A,11B
25
RED/ORN
25A,25B
12
BLK/ORN
12A,12B
26
RED/YEL
26A,26B
13
BLK/YEL
13A,13B
27
RED/GRN
27A,27B
14
BLK/GRN
14A,14B
*** The colors are for the pair of wires, i.e. pair 1 is WHT/BLK, meaning a white wire paired with a black wire.
8/8/2011
18
TABLE 1 - COLOR CODE 1J
CABLE TYPE
3PR24IS
18PR22OS
24PR16OS
4PR24IS
PAIRED
CABLE
COND.#
***WIRE
COLOR CODE
CONNECTION
BLOCK POINT #
PAIRED
CABLE
COND.#
*** WIRE
COLOR CODE
CONNECTION
BLOCK POINT #
1
BLK/RED
1,2
15
GRN/BLU
29,30
2
BLK/WHT
3,4
16
GRN/YEL
31,32
3
BLK/GRN
5,6
17
GRN/BRN
33,34
4
BLK/BLU
7,8
18
GRN ORN
35,36
5
BLK/YEL
9,10
19
WHT/BLU
37,38
6
BLK/BRN
11,12
20
WHT/YEL
39,40
7
BLK/ORN
13,14
8
RED/WHT
15,16
21
WHT/BRN
41,42
9
RED/GRN
17,18
22
WHT/ORN
43,44
10
RED/BLU
19,20
23
BLU/YEL
45,46
24
BLU/BRN
47,48
11
RED/YEL
21,22
25
*
BLU/ORN
49,NC
12
RED/BRN
23,24
26
*
YEL/BRN
NC,NC
13
RED/ORN
25,26
27
*
YEL/ORN
NC,NC
14
GRN/WHT
27,28
DRAIN
50
WIRE
8/8/2011
19
* The 5 wires indicated as 'NC' are to be taped back against the
cable jacket. they are not used at this time.
*** The colors are for the pair of wires, i.e. pair 1 is BLK/RED,
meaning a black wire paired with a red wire. The BLK wire
connects to terminal 1, and the RED to terminal 2.
TABLE 1 - COLOR CODE 1K
PAIRED
CABLE.
COND#.
***WIRE
COLOR CODE
PAIRED WIRE
COND.#
PAIRED CABLE
COND.#
***WIRE COLOR
CODE
PAIRED WIRE
COND.#
1
WHT/BLU
1A,1B
15
BLK/GRY
15A,15B
2
WHT/ORN
2A,2B
16
YEL/BLU
16A,16B
3
WHT/GRN
3A,3B
17
YEL/ORN
17A,17B
4
WHT/BRN
4A,4B
18
YEL/GRN
18A,18B
5
WHT/GRY
5A,5B
19
YEL/BRN
19A,19B
6
RED/BLU
6A,6B
20
YEL/GRY
20A,20B
7
RED/ORN
7A,7B
21
VIO/BLU
21A,21B
8
RED/GRN
8A,8B
22
VIO/ORN
22A,22B
9
RED/BRN
9A,9B
23
VIO/GRN
23A,23B
10
RED/GRY
10A,10B
24
VIO/BRN
24A,24B
11
BLK/BLU
11A,11B
25
VIO/GRY
25A,25B
12
BLK/ORN
12A,12B
13
BLK/GRN
13A,13B
14
BLK/BRN
14A,14B
*** The colors are for the pair of wires, i.e. pair 1 is WHT/BLU, meaning a white wire paired with a blue wire.
8/8/2011
20
TABLE 1 - COLOR CODE 1L
The following color sequence applies. Colors are given in the sequence
of Body, First (wide) tracer, Second (narrow) tracer, and Third (narrow) tracer.
USED WITH CABLE TYPE
50C16/3V
50C16TC
4C18OS
3C16/3V
6C16OS
CABLE COND.
NO.
WIRE COLOR
CODE
CABLE
COND. NO.
WIRE COLOR CODE
CABLE COND.
NO.
WIRE COLOR CODE
1
BLK
36
WHT/RED/GRN
71
WHT/BLK/GRN/ORN
2
RED
37
WHT/RED/BLU
72
WHT/BLK/GRN/GRY
3
WHT
38
WHT/RED/BRN
73
WHT/BLK/GRN/VIO
4
GRN
39
WHT/RED/VIO
74
WHT/BLK/YEL/BLU
5
ORN
40
WHT/GRN/BLK
75
WHT/BLK/YEL/BRN
6
BLU
76
WHT/BLK/YEL/ORN
7
BRN
41
WHT/GRN/RED
77
WHT/BLK/YEL/GRY
8
YEL
42
WHT/GRN/GRN
78
WHT/BLK/YEL/VIO
9
VIO
43
WHT/GRN/BLU
79
WHT/BLK/BLU/BRN
10
GRY
44
WHT/GRN/BRN
80
WHT/BLK/BLU/ORN
45
WHT/GRN/VIO
11
PNK
46
WHT/BLU/BLK
81
WHT/BLK/BLU/GRY
12
TAN
47
WHT/BLU/RED
82
WHT/BLK/BLU/VIO
13
RED/GRN
48
WHT/BLU/GRN
83
WHT/BLK/BRN/ORN
14
RED/YEL
49
WHT/BLU/BLU
84
WHT/BLK/BRN/GRY
8/8/2011
21
15
RED/BLK
50
16
WHT/BLK
17
WHT/RED
51
18
WHT/GRN
19
20
WHT/BLU/BRN
85
WHT/BLK/BRN/VIO
86
WHT/BLK/ORN/GRY
WHT/BLU/VIO
87
WHT/BLK/ORN/VIO
52
WHT/BRN/BLK
88
WHT/BLK/GRY/VIO
WHT/YEL
53
WHT/BRN/RED
89
WHT/RED/BLK/GRN
WHT/BLU
54
WHT/BRN/GRN
90
WHT/RED/BLK/YEL
55
WHT/BRN/BLU
21
WHT/BRN
56
WHT/BRN/BRN
91
WHT/RED/BLK/BLU
22
WHT/ORN
57
WHT/BRN/VIO
92
WHT/RED/BLK/BRN
23
WHT/GRY
58
WHT/VIO/RED
93
WHT/RED/BLK/ORN
24
WHT/VIO
59
WHT/VIO/GRN
94
WHT/RED/BLK/GRY
25
WHT/BLK/RED
60
WHT/VIO/BLU
95
WHT/RED/BLK/VIO
26
WHT/BLK/GRN
96
WHT/RED/GRN/YEL
27
WHT/BLK/YEL
61
WHT/BLK/RED/GRN
97
WHT/RED/GRN/BLU
28
WHT/BLK/BLU
62
WHT/BLK/RED/YEL
98
WHT/RED/GRN/BRN
29
WHT/BLK/BRN
63
WHT/BLK/RED/BLU
99
WHT/RED/GRN/ORN
30
WHT/BLK/ORN
64
WHT/BLK/RED/BRN
100
WHT/RED/GRN/GRY
65
WHT/BLK/RED/ORN
31
WHT/BLK/GRY
66
WHT/BLK/RED/GRY
32
WHT/BLK/VIO
67
WHT/BLK/RED/VIO
33
WHT/BLK/BLK
68
WHT/BLK/GRN/YEL
34
WHT/RED/BLK
69
WHT/BLK/GRN/BLU
35
WHT/RED/RED
70
WHT/BLK/GRN/BRN
8/8/2011
22
TABLE 1 - COLOR CODE 1M
This cable is composed of solid colored wires, with a number for each wire printed on each wire.
The NUMBERS are to be followed to determine the connection order.
Listed below is a sample of one segment of this cable, AS AN EXAMPLE ONLY. There is no
assurance that other segments will have the same colors associated with the same numbers.
USED WITH CABLE TYPE
19C12/6V
CABLE COND. NO.
WIRE COLOR CODE
CABLE COND. NO.
WIRE COLOR CODE
1
BLK
11
BRN
2
RED
12
BLK
3
BLU
13
BLU
4
ORN
14
ORN
5
YEL
15
YEL
6
BRN
16
BRN
7
RED
17
BLK
8
BLU
18
RED
9
ORN
19
ORN
10
YEL
8/8/2011
23
TABLE 1 - COLOR CODE 1N
The following color sequence applies. Colors are given in the
sequence of Body, First (wide) tracer, Second (narrow) tracer,
and Third (narrow) tracer.
USED WITH CABLE TYPE
50C16/3V
27C20OS
CABLE COND.
NO.
WIRE COLOR CODE
CABLE COND. NO.
WIRE COLOR CODE
CABLE COND.
NO.
WIRE COLOR CODE
1
BLK
36
WHT/RED/YEL
71
WHT/BLK/ORN/VIO
2
BRN
37
WHT/RED/GRN
72
WHT/BLK/ORN/GRY
3
RED
38
WHT/RED/BLU
73
WHT/BLK/YEL/GRN
4
ORN
39
WHT/RED/VIO
74
WHT/BLK/YEL/BLU
5
YEL
40
WHT/RED/GRY
75
WHT/BLK/YEL/VIO
6
GRN
76
WHT/BLK/YEL/GRY
7
BLU
41
WHT/ORN/YEL
77
WHT/BLK/GRN/BLU
8
VIO
42
WHT/ORN/GRN
78
WHT/BLK/GRN/VIO
9
GRY
43
WHT/ORN/BLU
79
WHT/BLK/GRN/GRY
10
WHT
44
WHT/ORN/VIO
80
WHT/BLK/BLU/VIO
45
WHT/ORN/GRY
11
WHT/BLK
46
WHT/YEL/GRN
81
WHT/BLK/BLU/GRY
12
WHT/BRN
47
WHT/YEL/BLU
82
WHT/BLK/VIO/GRY
13
WHT/RED
48
WHT/YEL/VIO
83
WHT/BRN/RED/ORN
14
WHT/ORN
49
WHT/YEL/GRY
84
WHT/BRN/RED/YEL
15
WHT/YEL
50
WHT/GRN/BLU
85
WHT/BRN/RED/GRN
8/8/2011
24
16
WHT/GRN
86
WHT/BRN/RED/BLU
17
WHT/BLU
51
WHT/GRN/VIO
87
WHT/BRN/RED/VIO
18
WHT/VIO
52
WHT/GRN/GRY
88
WHT/BRN/RED/GRY
19
WHT/GRY
53
WHT/BLU/VIO
89
WHT/BRN/ORN/YEL
20
WHT/BLK/BRN
54
WHT/BLU/GRY
90
WHT/BRN/ORN/GRN
55
WHT/VIO/GRY
21
WHT/BLK/RED
56
WHT/BLK/BRN/RED
91
WHT/BRN/ORN/BLU
22
WHT/BLK/ORN
57
WHT/BLK/BRN/ORN
92
WHT/BRN/ORN/VIO
23
WHT/BLK/YEL
58
WHT/BLK/BRN/YEL
93
WHT/BRN/ORN/GRY
24
WHT/BLK/GRN
59
WHT/BLK/BRN/GRN
94
WHT/BRN/YEL/GRN
25
WHT/BLK/BLU
60
WHT/BLK/BRN/BLU
95
WHT/BRN/YEL/BLU
26
WHT/BLK/VIO
96
WHT/BRN/YEL/VIO
27
WHT/BLK/GRY
61
WHT/BLK/BRN/VIO
97
WHT/BRN/YEL/GRY
28
WHT/BRN/RED
62
WHT/BLK/BRN/GRY
98
WHT/BRN/GRN/BLU
29
WHT/BRN/ORN
63
WHT/BLK/RED/YEL
99
WHT/BRN/GRN/VIO
30
WHT/BRN/YEL
64
WHT/BLK/RED/GRN
100
WHT/BRN/GRN/GRY
65
WHT/BLK/RED/BLU
31
WHT/BRN/GRN
66
WHT/BLK/RED/VIO
32
WHT/BRN/BLU
67
WHT/BLK/RED/GRY
33
WHT/BRN/VIO
68
WHT/BLK/ORN/YEL
34
WHT/BRN/GRY
69
WHT/BLK/ORN/GRN
35
WHT/RED/ORN
70
WHT/BLK/ORN/BLU
8/8/2011
25
TABLE 1 - COLOR CODE 1P
USED WITH CABLE TYPE
15PR22OS
2PR22OS
3PR24IS
12PR22OS
9PR24IS
PAIRED
CABLE
COND.#
***WIRE
COLOR CODE
PAIRED
CABLE.
COND.#
***WIRE
COLOR CODE
1
BLK/RED
15
GRN/BLU
2
BLK/WHT
16
GRN/YEL
3
BLK/GRN
17
GRN/BRN
4
BLK/BLU
18
GRN ORN
5
BLK/YEL
19
WHT/BLU
6
BLK/BRN
20
WHT/YEL
7
BLK/ORN
8
RED/WHT
21
WHT/BRN
9
RED/GRN
22
WHT/ORN
10
RED/BLU
23
BLU/YEL
24
BLU/BRN
11
RED/YEL
25
BLU/ORN
12
RED/BRN
26
BRN/YEL
13
RED/ORN
27
BRN/ORN
14
GRN/WHT
*** The colors are for the pair of wires, i.e. pair 1 is
BLK/RED, meaning a black wire paired with a red wire. The
BLK wire connects to terminal 1, and the RED to terminal 2.
8/8/2011
26
TABLE 1 - COLOR CODE 1Q
Used With CABLE TYPE 3C20/3V 3C16FLX
4C16FLX 3C14FLX
CABLE
WIRE COLOR
CABLE
WIRE COLOR CODE
COND.
CODE
COND.
NO.
NO.
1
BLK
20
ORN/BLU
2
RED
21
YEL/BLU
3
WHT
22
BRN/BLU
4
BLU
23
BLK/ORN
5
ORN
24
RED/ORN
6
YEL
25
BLU/ORN
7
BRN
26
YEL/ORN
8
RED/BLK
27
BRN/ORN
9
BLU/BLK
28
BLK/YEL
10
ORN/BLK
29
RED/YEL
11
YEL/BLK
30
BLU/YEL
12
BRN/BLK
31
ORN/YEL
13
BLK/RED
32
BRN/YEL
14
BLU/RED
33
BLK/BRN
15
ORN/RED
34
RED/BRN
16
YEL/RED
35
BLU/BRN
17
BRN/RED
36
ORN/BRN
18
BLK/BLU
37
YEL/BRN
19
RED/BLU
8/8/2011
27
TABLE 1 - COLOR CODE 1R
USED WITH CABLE TYPE
5PR20OS
VAT7S
COLOR
CODE
PAIR
NO.
COLOR
CODE
PAIR
NO.
1
WHT
1A
A
5
WHT
3A
E
2
BLK
1B
B
6
RED
3B
F
3
WHT
2A
C
7
WHT
4A
G
4
BRN
2B
D
-
NONE
--
H
MS8S
VAT7S
MS8S
***The 5th pair (white/yellow) and the orange wire from the 4th
pair are not used - cut off.
TABLE 1 - COLOR CODE 1S
USED WITH CABLE TYPE
2PR22IS
CABLE PAIR NO.
WIRE COLOR CODE
1A
BLK
1B
RED
2A
BLK
2B
WHT
DRAIN
BARE
8/8/2011
28
TABLE 1 - COLOR CODE 1T
USED WITH CABLE TYPE
16PR16IS
The cable contains twisted pairs. Each pair consists of a white
(or red), a black and a drain wire. Each white and
black conductor is printed with a pair number. The white wire
is the first of "A" wire. The black wire is the "B"
wire. The drain is the "C" wire. Wire in white, black,
drain sequence, starting with the first terminal indicated.
Repeat for each additional pair to be connected.
TABLE 1 - COLOR CODE 1U
USED WITH CABLE TYPE
2C22MS
CABLE COND. NO.
WIRE COLOR CODE
1
CLR
2
BLK
3
RED
4
GRN
5
BLU
8/8/2011
29
TABLE 1 - COLOR CODE 1V
Used With CABLE TYPE
12C20J
CABLE COND. NO.
WIRE COLOR CODE
CABLE COND. NO.
WIRE COLOR CODE
1
BLK
11
PNK
2
WHT
12
TAN
3
RED
4
GRN
5
BRN
6
BLU
7
ORN
8
YEL
9
VIO
10
GRY
8/8/2011
30
TABLE 1 - COLOR CODE 1W
USED WITH CABLE TYPE
7C22OS
CABLE COND. NO.
WIRE COLOR CODE
1
BLK
2
RED
3
ORN
4
GRN
5
BLU
6
WHT
7
WHT/BLK
8/8/2011
31
TABLE 1 - COLOR CODE 1X
USED WITH CABLE TYPE
51PR22OS
PAIRED CABLE COND.#
WIRE COLOR CODE
1
BLK/RED
27
BRN/YEL
2
BLK/WHT
28
PUR/RED
3
BLK/GRN
29
PUR/WHT
4
BLK/BLU
30
PUR GRN
5
BLK/BRN
31
PUR/BLU
6
BLK/YEL
32
PUR/BRN
7
BLK/ORN
33
PUR/YEL
8
RED/GRN
34
PUR/ORN
9
RED/WHT
35
PUR/SLA
10
RED/BLU
36
PUR/BLK
11
RED/YEL
37
SLA/RED
12
RED/BRN
38
SLA/WHT
13
RED/ORN
39
SLA/GRN
14
GRN/BLU
40
SLA/BLU
15
GRN/WHT
41
SLA/BRN
16
GRN/BRN
42
SLA/YEL
17
GRN/ORN
43
SLA/ORN
18
GRN/YEL
44
SLA/BLK
8/8/2011
PAIRED CABLE COND. #
WIRE COLOR CODE
32
19
WHT/BLU
45
WHT-BLK/RED
20
WHT/BRN
46
WHT-BLK/GRN
21
WHT/ORN
47
WHT-BLK/BLU
22
WHT/YEL
48
WHT-BLK/BRN
23
BLU/BRN
49
WHT-BLK/YEL
24
BLU/ORN
50
WHT-BLK/ORN
25
BLU/YEL
51
WHT-BLK/PUR
26
BRN/ORN
*** The colors are for the pair of wires, i.e. pair 1 is BLK/RED,
meaning a black wire paired with a red wire. The
BLK wire connects to terminal 1, and the RED to terminal 2.
TABLE 1 COLOR CODE 1Y
USED WITH CABLE TYPE
FIOPMM12
FIOPMM24
FIOPMM48
FIBER
COLOR
FIBER
COLOR
1
BLUE
7
RED
2
ORANGE
8
BLACK
3
GREEN
9
YELLOW
4
BROWN
10
VIOLET
5
SLATE
11
DASHED BLUE
6
WHITE
12
DASHED ORANGE
SPECIAL NOTE: CABLE CORE CONSISTS OF UP TO 8 BUNDLES, EACH CONTAINING
12 FIBERS. BUNDLES ARE IDENTIFIED BY COLOR-CODED YARN BINDERS. BINDER
COLOR CODE FOLLOWS SAME CODE AS FIBER COLOR CODE.
8/8/2011
33
TABLE 1 - COLOR CODE 1Z
USED WITH CABLE TYPE
25PR24OS
PIN
WIRE COLOR CODE
PIN
1
WHT/BRN
26
2
WHT/ORN
27
3
WHT/YEL
28
4
WHT/BLU
29
5
WHT/GRN
30
6
RED/BRN
31
7
RED/ORN
32
8
RED/GRN
33
9
RED/WHT
34
10
RED/BLU
35
11
RED/YEL
36
12
RED/BLK
37
13
BLU/ORN
38
14
BLU/BRN
39
15
BLU/YEL
40
16
BLU/GRN
41
17
BLU/BLK
42
18
BLK/ORN
43
19
BLK/GRN
44
20
BLK/BRN
45
8/8/2011
34
21
BLK/WHT
46
22
BLK/YEL
47
23
GRN/YEL
48
24
GRN/BRN
49
25
GRN/ORN
50
*** The colors are for the pair of wires, i.e. pair 1 is WHT/BRN,
meaning a WHT wire paired with a BRN wire. The WHT wire
connects to terminal 1, and the BRN to terminal 26.
8/8/2011
35
TABLE 2Z – COLOR CODING OF FIBER OPTIC CABLES (In accordance with EIA/TIA-598)
Fiber Color
Abbreviation
Buffer Tube Value
Fiber Value
Captar Coding
BLUE
BL
0
1
1
ORANGE
OR
12
2
2
GREEN
GR
24
3
3
BROWN
BR
36
4
4
SLATE
SL
48
5
5
WHITE
WH
60
6
6
RED
RD
72
7
7
BLACK
BK
84
8
8
YELLOW
YL
96
9
9
VIOLET
VL
108
10
A
ROSE
RO
120
11
B
AQUA
AQ
132
12
C
NOTE: To calculate the fiber numerical value, take the buffer tube value and add the fiber value.
For example, WH fiber in the YL buffer is actually fiber number 96+6=102.
NOTE: Captar coding for the fiber will be performed in two parts. One listing will be for the fiber
cable sheath. For coding the fiber to be used, code the fiber with the cable number and then the
Buffer Tube Value and Fiber Value respectively. For example, using fiber 102 will get the coding
LC0XXXX96.
8/8/2011
36
TABLE 1 - COLOR CODE 1a
USED WITH CABLE TYPE
37C28FLT
PIN
WIRE COLOR CODE
1
BRN
20
BLK
2
RED
21
BRN
3
ORN
22
RED
4
YEL
23
ORN
5
GR
24
YEL
6
BLU
25
GRN
7
VIO
26
BLU
8
GRY
27
VIO
9
WHT
28
GRY
10
BLK
29
WHT
11
BRN
30
BLK
12
RED
31
BRN
13
ORN
32
RED
14
YEL
33
ORN
15
GRN
34
YEL
16
BLU
35
GRN
17
VIO
36
BLU
18
GRY
37
VIO
19
WHT
8/8/2011
PIN
WIRE COLOR CODE
37
TABLE 1 - COLOR CODE 1b
USED WITH CABLE TYPE
4PR24IS
PAIRED
CABLE
COND.#
1
2
3
4
WIRE
COLOR
CODE
BRN-WHT/BRN
ORN-WHT/ORN
GRN-WHT/GRN
BLU-WHT/BLU
TABLE 1 - COLOR CODE 1c
CABLE
COND.
NO.
1
2
WIRE
COLOR
CODE
RED
GRN
8/8/2011
38
568A Wiring
Pair #
1 - White/Blue
2 - White/Orange
3 - White/Green
4 - White/Brown
Wire
White/Blue
Blue
White/Orange
Orange
White/Green
Green
White/Brown
Brown
Pin #
5
4
3
6
1
2
7
8
568B Wiring
Pair #
1) White/Blue
2) White/Orange
3) White/Green
4) White/Brown
8/8/2011
Wire
White/Blue
Blue
White/Orange
Orange
White/Green
Green
White/Brown
Brown
Pin #
5
4
1
2
3
6
7
8
39
TABLE 2 - Cable Types and Cable Descriptions
GENERAL CABLE NOTE:
(n)-(cable-type): (n) being a number larger than 1, means (n) runs of the indicated cable-type.
i.e. '5-250MCM' would mean that 5 runs of 250 MCM conductor are to be
used to make up the indicated cable. Another example might be '12-#16'
meaning that 12 runs of # 16 AWG wire (as specified below) are to
be used for the indicated cable. In this example, no wire color is specified,
implying that any color(s) may be used. The cable-plant coordination group is
to be informed of the color(s) actually used so that the related Installation
Schedule can then be up-graded to reflect the wiring as actually installed.
See color
CABLE TYPE
CABLE DESCRIPTION
CODE TABLE
#(nn)-(ccc)
'(nn)' is the AWG # for a single conductor, concentric
stranded, insulated wire, UL types: RHH or RHW, FR-1 rated
THHN or THWN, or XHHN for aluminum wires.
Okonite type 'Okolon' (single conductor) or equal. Note that
AWG#0 through AWG#0000 will be indicated as 1/0 through 4/0, respectively.
For the MCM series cables, sizes are defined as follows.
The definitions are for copper, and aluminum.
These abbreviations are sometimes used where listing space
will not permit the complete descriptor.
250MCM: 25MCM
25MCAL
300MCM: 30MCM
35MCAL
350MCM: 35MCM
35MCAL
500MCM: 50MCM
50MCAL
535MCM:
600MCM: 60MCM
60MCAL
750MCM: 75MCM
75MCAL
Unless otherwise specified, the conductor is copper. If it
is to be aluminum, the size is followed by the letters 'AL'.
For example, '3-#6AL' or '#2/0AL' indicates 3 runs of aluminum #6 AWG, or
1 run of aluminum #00 AWG, respectively.
'(ccc)' when included, is the color for the indicated conductor(s),
per table 1, above.
(Approximate outside diameter info, #12=0.1", #10=0.2",
#8=0.3",#6=0.3", #4=0.4", #2=0.5", #1=0.5",
1/0=0.6",2/0=0.6", 3/0=0.7", 4/0=0.7",
250MCMAL=0.733",350MCMAL=0.830",
500MCMAL=0.952",535MCM=1.3750",600MCMAL
=1.063",750MCMAL=1.159", 250MCM=0.85",
300MCM=0.82, 350MCM=0.96", 500MCM=1.10",
750MCM=1.32",1000MCM=1.47").
8/8/2011
Used with TERM.TYPE
(See Table 3)
LB25D8
LB30-6,LB30D6,LB30D8
LB35-8,LB35D8
LB50-8,LB50D8
LB53D8
LB60D8
LB75-8,LB75D8.
40
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
(nnn)MCM
Where (nnn) is the MCM size. See note under
'#(nn)-(ccc)' above.
(nnn)MCMAL
As above, except compact aluminum conductor. See note
under '#(nn)-(ccc)' above.
1010-100
10m CABLE, USED FOR TRANSVERSE TO AMPLIFIER.
MFR: METROLAB,S.A. VENDOR: GMW ASSOCIATES,REDWOOD CITY, CA.,
(650) 802-8292.
1011-3
3m CABLE, USED FOR TESLAMETER TO PROBE MULTIPLEXER. MFR:
METROLAB, S.A. VENDOR: GMW ASSOCIATES, REDWOOD CITY, CA.,
(650) 802-8292.
1080-2-7
7m CABLE, USED FOR PROBE, MINI TRANSVERSE, 0.09T TO
0.26T. MFR: METROLAB, S.A. VENDOR: GMW ASSOCIATES, REDWOOD
CITY, CA.,(650) 802-8292.
1080-4-7
7m CABLE, USED FOR PROBE, MINI TRANSVERSE, 0.35T TO
1.05T. MFR: METROLAB, S.A. VENDOR: GMW ASSOCIATES, REDWOOD
CITY, CA.,(650) 802-8292.
1/0-FLEX
#1/0 AWG, FLEXIBLE LOCOMOTIVE CABLE, 275/24 STRANDS, 2000 VOLT.
SLAC P/N 61-329-601-16-A012.
1/0TLSNH
1/0, FLEX, 90 DEG / 105 DEG. C, TC, LOW SMOKE NON-HALOGEN (LSNH), 600V.
INSULATION COLOR: BLACK, 0.630” O.D.
AMERICAN INSULATED WIRE CORP P/N 39892
#2-FLEX
#2 AWG, EXTRA FLEXIBLE CABLE,150 STRAND, 600V,
0.49" O.D., ALPHA NO. 7410
LB2-5,-6
#2/0FLX
#2/0 AWG, EXTRA FLEXIBLE CABLE, 325 STRANDS, 600V,
0.65" O.D., ALPHA #7413
LB03-8, LB03D8
#4/0FLX
#4/0 AWG, EXTRA FLEXIBLE CABLE, 550 STRANDS, 600V,
0.81"O.D., ALPHA #7415
LB049-3
LB25D8, LB25-8
4/0TLSNH
4/0,FLEX, 90DEG/105DEG. C, TC,LOW SMOKE NON-HALOGEN(LSNH),
600V. INSULATION COLOR BLACK, 0.810" O.D.,AMERICAN P/N40032
AMERICAN INSULATED WIRE CORP P/N 39784.
LB049-3, LB25D8
LB25-8
#10CJ
SINGLE CONDUCTOR, #10 AWG, 113 STRAND, EXTRA FLEXIBLE
TINNED COPPER WIRE WITH A CLEAR JACKET.
8/8/2011
LBR02-6,PP180C
41
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
1/4HEL
1/4" FOAM DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
0.29" O.D., 50 OHMS, ANDREW TYPE FHS1-50.
1/4HELA
1/4" AIR DIELECTRIC, HELIAX COAXIAL CABLE, JACKETED,
BRAIDED SHIELD CONSTRUCTION, 84147 RADIATION SENSING
CABLE, ANDREW TYPE 222793.
1/4HELB
1/4" HELIAX CABLE, AIR DIELECTRIC, 50 OHMS,
0.29" O.D., ANDREW CAT. #HS1RP-50.
SHVMOD
1/4HELS
1/4" FOAM DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
PHASE STABILIZED, 50 OHMS, 0.29" O.D.
ANDREWS P/N 35422-11, FHJ1-50, OR FSJ1-50.
N1/4HP
1/4HELSF
1/4" HELIAX, SUPERFLEXIBLE COAXIAL CABLE,
FOAM DIELECTRIC, 50 OHMS, PHASE STABILIZED,
0.29" O.D., TYPE FSJ1-50A, ANDREW CAT.#35422-33.
C41SW
1/4HSFX3
SET OF 3 EACH 1/4" HELIAX, SUPERFLEXIBLE COAXIAL
CABLE,FOAM N1/4HP DIELECTRIC, FIRE RETARDANT,50 OHMS,
PHASE MATCHED, 0.29" O.D.,ANDREW TYPE FSJ1RN-50B,
0.045 LB/FT.
1/2HEL
1/2" FOAM-DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
0.64" O.D., 50 OHMS, ANDREW TYPE LDF4-50.
N1/2HP, N1/2HJ
SP1/2H
1/2HELA
1/2" FOAM-DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
0.64" O.D., 50 OHMS, ANDREW TYPE LDF4-50A.
N1/2HA
1/2HELFR
1/2" HELIAX. SUPERFLEXIBLE COAXIAL CABLE,
NON-HALOGENATED, LLRF FIRE RETARDANT POLYOLEFIN.
FOAM PE, COPPER CLAD ALUMINUM WIRE,.53IN OD, GRAY,
CORRUGATED COPPER. 50 OHM ANDREWS P/N # FSJ4RN-50B
1/2HELGF
1/2" HELIAX COAXIAL CABLE, AIR DIELECTRIC, GAS-TIGHT.
0.58" O.D., ANDREWS P/N HJ4-50.
N1/2HG, N1/2HD
1/2HELS
SAME AS 1/2"HEL EXCEPT: PHASE STABILIZED, ANDREW
35422-14. OBSOLETE
N1/2HP, N1/2HJ
SP1/2H
8/8/2011
N1/4HP
42
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
1/2HELSF
1/2" HELIAX, SUPERFLEXIBLE COAXIAL CABLE,FOAM
DIELECTRIC, 50 OHMS, PHASE STABILIZED, ANDREW
FSJ4-50B, TYPE #35422-24, 0.52" O.D.P
N1/2MH, N1/2HP
1/2RD
1/2" FOAM DIELECTRIC SEMI-RIGID JACKETED
COAXIAL CABLE, TIMES WIRE & CABLE NO. JT-4500J,
0.625" O.D., 75OHM, CATV SYSTEM CABLE.P
S1/2RP, F1/2RP
1/2RDB
1/2" FOAM DIELECTRIC SEMI-RIGID JACKETED
COAXIAL CABLE, DIRECT BURIAL, TIMES WIRE & CABLE NO
JT-4500JB, 5/8" O.D., 75OHM, CATV SYSTEM CABLE.
S1/2RP
3/4RGD
3/4" FOAM DIELECTRIC SEMI-RIGID JACKETED
COAXIAL CABLE, TIMES WIRE & CABLE NO. JT-4750J, 7/8"
O.D.,75OHM, CATV SYSTEM CABLE.
S3/4RP
3/8HEL
3/8" FOAM DIELECTRIC SEMI-RIGID, JACKETED,
COAXIAL CABLE, CORRUGATED COPPER OUTER CONDUCTOR,
0.44" O.D., 50 OHMS, ANDREW TYPE LDF2-50.
N3/8HP
3/8HELFR
3/8" HELIAX. COAXIAL CABLE, NON-HALOGENATED, FIRE
RETARDANT, LLRF POLYOLEFIN. FOAM PE COPPER CLAD
ALUMINUM WIRE, GRAY, CORRUGATED COPPER OUTER CONDUCTOR,
.45” OD, 50 OHM ANDREWS P/N LDF2RN-50
3/8HELSF
3/8" EXTRA FLEXIBLE HELIAX CABLE, FIRE RETARDANT JACKET,
ANDREWS P/N EFX2RN-50 OHM.
E2TSM (SMA3/8H)
3/8HELX4
SPECIAL SET OF 4 EACH 3/8"HELIAX COAXIAL CABLES,
TIMED, MATCHED AND LABELED FOR BEAM POSITION MONITORS.
TREATED AS A SINGLE CABLE.
N3/8HF
5/8HELAN
5/8" (NOMINAL SIZE) HELIAX COAXIAL CABLE. COPPER OUTER
CONDUCTOR WITH ANNULAR CORRUGATION. 0.870 OD. LOW-SMOKE,
ZERO HALOGEN JACKET. ANDREW PART NUMBERS LDF4.5RK-50
(BLACK),LDF4.5RN-50 (GREY).
7/8HEL
7/8" FOAM DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
1.1" O.D., 50 OHMS, ANDREW TYPE LDF5-50.
N7/8HJ, SP7/8H
7/8HELGF
7/8" HELIAX COAXIAL CABLE,AIR DIELECTRIC, GAS-TIGHT.
1.11" O.D.,ANDREWS P/N HJ5-50
N7/8GF
8/8/2011
43
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
7/8HELS
7/8" FOAM DIELECTRIC, HELIAX COAXIAL CABLE,
JACKETED, CORRUGATED COPPER OUTER CONDUCTOR,
PHASE STABILIZED, 50 OHMS, 1.1" O.D. ANDREWS
P/N 35422-15,LDF5-50A.
N7/8HJ, SP7/8H
1”WCAL
WATER COOLED ALUMINUM CABLE, 1" DIAMETER,
1.25" O.D., 1000VDC.
FLAG-1, FLAG-2
1.25HELS
1 1/4" HELIAX COAXIAL CABLE, FOAM DIELECTRIC,
50 OHM, 1.55" O.D.,15" MIN. RADIUS, ANDREWS P/N LDF6-50.
1C12T6V
ONE CONDUCTOR, #12AWG, TYPE THHN, 7 STRAND,600V.
SLAC S/N61-328-366-05
1C18E6V
ONE CONDUCTOR, #18AWG, BLACK TYPE E,STRANDED,600V.
SLAC S/N61-328-307-01
1C20RR6V
ONE CONDUCTOR, #20AWG INSULATED WIRE, RADIATION
RESISTANT, 600V, 0.1" O.D. MANCO WIRE AND CABLE CO.
UL-3271, #XML1030U(032).
1MTW-B
ONE CONDUCTOR, #1AWG, STRANDED, WIRE TYPE MTW, BLACK,
TFF, AWM, TEW, 600V, 500 FEET SPOOL.
1PR1T6V
ONE PAIR, #1AWG, STRANDED, TRAY CABLE, 600V,
1.075" O.D., UNSHIELDED, ANIXTER CAT. #3G-0102.
1F
1PR4T6V
ONE PAIR, #4AWG, STRANDED, TRAY CABLE, 600V
0.787" O.D., UNSHIELDED, ANIXTER CAT. #3G-0402
1F
1PR6T6V
ONE PAIR, #6AWG, STRANDED, TRAY CABLE, 600V,
0.645" O.D., UNSHIELDED, ANXTER CAT. #3G-0602.
1F
1PR16AS
ONE PAIR, ARMORED CABLE, 300V, #16 AWG, STRANDED,
TINNED-COPPERWIRE, OVERALL SHIELD AND DRAIN WIRE,
0.24" O.D., TRAY CABLE, OKONITE CLX TYPE P-OS 564-10-3401.
1F
LSB#6, XLR3P
1PR16OS
ONE PAIR, #16AWG, STRANDED, COPPER WIRE, OVERALL
SHIELD, TRAY CABLE 0.301" O.D.,BELDEN CAT. #9342
1B
LFB, LSB#8, LFR
MS10-A, MS10S,
MS3P, BP-02,
LRB#6, LRB3/8
8/8/2011
44
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
1PR16T3V
ONE PAIR, #16AWG, 300V, UNSHIELDED, TRAY CABLE, 7-STRAND
BARE SOFT ANNEALED COPPER, 0.26" O.D., OKONITE TYPE
P-NS, CAT. #260-10-4401.
1PR16TS
ONE PAIR, #16AWG, 600V, OVERALL SHIELDED, TYPE "T"
INSTRUMENTATION CABLE. 0.31" O.D. OKONITE#264-20-4401,
TYPE P-OS.
1PR16TZL
ONE PAIR, #16AWG, 300V, OVERALL SHIELDED, (BELDFOIL)
TEFZEL INSULATED, 0.212" O.D. BELDEN CAT#85231.
1PR18AS
ONE PAIR, ARMORED CABLE, #18AWG.
1PR18OS
ONE PAIR, #18AWG, 600V, STRANDED, OVERALL SHIELDED,
0.279" O.D. TRAY CABLE, BELDEN CAT. #9341
1PR18TC
ONE PAIR, #18AWG, TRAY CABLE, OVERALL SHIELDED.
MFR: OKONITE.
1PR18T6V
ONE PAIR, #18AWG, STRANDED, TRAY CABLE, 600V,
UNSHIELDED,0.276" O.D., BELDEN CAT. #9486.
1F
LFR, LSR#6
1PR20OS
ONE PAIR, #20AWG, STRANDED, TINNED COPPER
CONDUCTORS, OVERALL SHIELDED, TRAY CABLE, 300 VOLT,
0.217" O.D., BELDEN #9320
1F
LRR#6,BP-02,LEMO4P,
LFR,LSR,LFRM
LRR1/4,LSR#6,TT4S
TT4P,TT12S,MS8P,
SOLDER,MS6P,MS3S
1PR20BH
ONE PAIR, #20AWG, STRANDED, COPPER WIRE, ALUMINUM FOIL
SHIELD, W/DRAIN WIRE BELDEN #9463, BLUE HOSE (TM)
ALLEN BRADLEY CAT# 1770 CD.
1PR20SCC
ONE PAIR, #20 AWG, SOLID CONDUCTOR, CHROMEL (‘+’ OR YELLOW)
AND ALUMEL(‘-‘ OR RED) COLORED PAIRS WITH #22AWG BARE SOLID
CONDUCTOR DRAIN WIRE. ENCLOSED IN ALUMINIZED POLYESTER SHIELD
FOIL AND THEN A YELLOW, UL LISTED TYPE PLTC PVC JACKET,
RATED FOR 300V. 0.230" O.D., OMEGA P/N EXPP-K-20S-TWSH.
1PR22OS
ONE PAIR, #22AWG, STRANDED, COPPER WIRE, OVERALL
BELDFOIL SHIELDED, TRAY CABLE, 300 VOLT, 0.201" O.D.,
BELDEN P/N 9322
1L
LFR, TT19P, LSR#6
MS10SB, TT4P
TT12P, MS3S-S
8/8/2011
1F
WNY, LFB, LSB#6
XLR3S, XLR3P, MS10SA
1F
45
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
1PR22PLT
ONE PAIR, #22AWG, EIA RS-485, STRANDED, OVERALL
BELDFOIL SHIELDED,PLTC TRAY CABLE, 300 VOLT,
0.284" O.D.,BELDEN P/N: 3105A
1PR22SR
ONE PAIR, #22AWG., TINNED COPPER, S-R PVC INSULATED,
TWISTED PAIR, BELDFOIL ALUM-POLY SHIELD, CHROME PVC JACKET,
300V, 0.186" O.D., BELDEN CAT#9462.
1PR22TEF
ONE TWISTED PAIR, #22 AWG, STRANDED TINNED COPPER,
TEFLON INSULATED, BELDFOIL SHIELDED, 0.118" O.D.,
BELDEN CAT. #82761.
1PR24CC
ONE PAIR, #24 AWG, COPPER CONSTANTAN, SOLID WIRE,
COPPER INNER INSULATION IS BLUE(POSITIVE) AND CONSTANTAN
INNER INSULATION IS RED(NEGATIVE), FIBERGLASS OVERALL
JACKET AND INNER INSULATION. ANSI TYPE "T", 0.050" X 0.080" O.D.
OMEGA CAT. #GG-T-24. CABLE TRAY APPLICATION: WHEN ROUTING
THIS THEMOCOUPLE WIRE IN A CABLE TRAY, PROTECT THE WIRE
OR WIRES USING INNERDUCT TUBING, MFG: SUPERFLEX, FLEXIBLE
SPLIT TUBING (GRAY – FLAME RETARDANT), ITEM #125-XXXXG.
1PR24DOS
ONE TWISTED PAIR, #24 AWG, EIA RS-485,
DOUBLE SHIELDED: FOIL AND BRAID WITH DRAIN WIRE,
300 VOLT, 0.232" O.D.MFG: BELDEN, P/N: 9841.
1PR24OS
TWINAX CABLE, ONE PAIR, #24AWG, STRANDED, 0.129"
O.D., MIL-SPEC. MIL-C-17, BELDEN CAT. #81553
1PR24FRP
ONE PAIR, #24 AWG, STRANDED BARE COPPER CONDUCTORS,
WITH FLUOROCOPOLYMER .006" THICK INSULATION, FOIL
SHIELDED, PLENUM-RATED, RATED 150V, 0.114" O.D.
ALPHA CAT. #58401.
1PR24PLN
ONE PAIR, #24 AWG, PLENUM CABLE, NEC 725-(b), TINNED
COPPER, TEFLON INSULATED WITH BELDFOIL OVERALL SHIELD,
0.152" O.D., MFG BELDEN, P/N 88641.
8/8/2011
TERM.TYPE
(See Table 3)
LEMO-A
46
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
1PR28CC
ONE PAIR, #28 AWG, COPPER-CONSTANTAN SOLID WIRE,
COPPER INNER INSULATION IS BLUE(POSITIVE) AND
CONSTANTAN INNER INSULATION IS RED(NEGATIVE),
WITH FIBERGLASS OVERALL JACKET, ANSI TYPE 'T',
OMEGA CAT-# GG-T-28, 0.045" X 0.070"O.D.
CABLE TRAY APPLICATION: WHEN ROUTING THIS THEMOCOUPLE
WIRE IN A CABLE TRAY, PROTECT THE WIRE OR WIRES USING
INNERDUCT TUBING, MFG: SUPERFLEX, FLEXIBLE SPLIT TUBING
(GRAY – FLAME RETARDANT), ITEM #125-XXXXG.
1RMMTLN
1-RIBBON, (12-STRAND), 50/125uM LASER-OPTIMIZED,
MULTI-MODE FIBER, (550M @ 10 GIGABIT), LOW-SMOKE,
ZERO-HALOGEN JACKET. CORNING PART NUMBER 012TCZ-14190-20.
1RSMTLN
1-RIBBON, (12-STRAND), 9/125uM, SINGLE-MODE FIBER OPTIC
CABLE, LOW-SMOKE, ZERO HALOGEN JACKET. CORNING PART
NUMBER 012ECZ-14101-20.
1THHN
ONE CONDUCTOR, #1 AWG, THHN, BLACK, 19 STRAND, 600V.
SLAC S/N 61-328-373-01.
1TPR22OS
ONE TWISTED PAIR, #22AWG, OVERALL SHIELDED.
2/0 WELD
#2/0 WELDING CABLE.
2/0TLSNH
2/0, 90DEG/105DEG. C, TC, LOW SMOKE NON-HALOGEN
(LSNH), 600V.INSULATION COLOR BLACK, 0.740" O.D.,
AMERICAN PART # 40026.
250WELD
250MCM WELDING CABLE. ONE COPPER CONDUCTOR # 250 KCM,
FLEXIBLE WELDING CABLE, THERMOSET JACKETTED, CLASS K
ROPE STRANDED,(2450 STRANDS) 105 DEGREES "C", 0.925 O.D.,
ANIXTER CAT # 5J-2501
2C1TLSNU
TWO CONDUCTOR,#1AWG,600V,19 STRAND,UNSHIELDED, 90DEG. C, LOW SMOKE
NON-HALOGENATED (LSNH), POWER TRAY CABLE, TC, 1.050" O.D.,
NO DRAIN WIRE. LAKE CABLE P/N VXH12.
8/8/2011
TERM.TYPE
(See Table 3)
STRIP, TC-CCP
TC-CCS, TC-JNC
TC-SLV, W1, TCSCCP
LB3/0
47
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
2C2TLSNH
TWO CONDUCTOR #2 AWG 19 STRAND,SHIELDED,AVERAGE INSULATION
THICKNESS 45 MILS, AVERAGE JACKET THICKNESS 80 MILS, NOMINAL
CABLE O.D. 0.975 IN, NOMINAL CABLE WEIGHT 680 LBS/1000 FT.
MULTI-CONDUCTOR, 600V, HEAT, MOISTURE, AND SUNLIGHT RESISTANT,
BLACK, POLYOLEFIN OR EQUIVALENT LOW SMOKE ZERO HALOGENATED
INSULATING MATERIAL, WET OR DRY LOCATION AT 90 DEGREES C.
PART # DRAKA 400287. LAKE CABLE P/N VXH22S(19)(W/DRAIN WIRE)
2C2TLSNU
TWO CONDUCTOR,#2AWG,600V,19 STRAND,UNSHIELDED, 90DEG. C,
TC,LOW SMOKE NON-HALOGENATED (LSNH),WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE) INSULATED CIRCUIT
CONDUCTORS AND CROSS-LINKED POLYOLEFIN(XLPO)JACKET,0.918"
O.D., NO DRAIN WIRE. LAKE CABLE P/N VXH22(19).
2C2T6V
TWO CONDUCTORS, #2AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, UNSHIELDED, TRAY CABLE, 90 DEGREE C,
600V, 0.787" O.D., ANIXTER CAT. #3G-0202
2C2TS6V
TWO CONDUCTORS,#2AWG,COPPER CONDUCTORS, 600V, 90C TRAY-RATED,
XLPE BLACK INSULATION (BLACK AND WHITE INDIVIDUAL CONDUCTORS),
UV RESISTANT (SUN RESISTANT). O.D.= 0.975 MANUFACTURER:
TAMAQUA CABLE(MANCO P/N M0202/7 XL02G).
2C4T6V
TWO CONDUCTORS, #4AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, UNSHIELDED, TRAY CABLE, 90 DEGREE C, 600V,
0.787" O.D., ANIXTER CAT. #3G-0402.
2C6LSNH
NUMBER & CIRCUIT CONDUCTOR SIZE 2C/#6 AWG, AVERAGE
INSULATION THICKNESS 45 MILS, AVERAGE JACKET THICKNESS
60 MILS, NOMINAL CABLE 0.775" O.D. NOMINAL CABLE WEIGHT
378 LBS/1000 FT. MULTI-CONDUCTOR, 600V, HEAT, MOISTURE
AND SUNLIGHT RESISTANT, BLACK, POLYOLEFIN OR EQUIVALENT
LOW SMOKE HALOGENATED INSULATING MATERIAL. WET OR DRY LOCATION
AT 90 DEGREES C. PART # DRAKA 382559
2C4TLN
TWO CONDUCTOR, #4AWG,19 STRAND,SHIELDED,90DEG. C, TC,
LOW SMOKE NON-HALOGENATED(LSNH), WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN (XLPO) JACKET, 600V 0.75" O.D.
LAKE CABLE P/N VXH42S(19) (W/DRAIN WIRE)
8/8/2011
TERM.TYPE
(See Table 3)
LB2D6, LB206S
1F
LB2-5
1F
48
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
2C4TLNU
TWO CONDUCTOR, #4AWG,600V,19 STRAND,UNSHIELDED, 90DEG. C, TC,
LOW SMOKE NON-HALOGENATED(LSNH), WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN (XLPO) JACKET, 0.771" O.D., NO
DRAIN WIRE. LAKE CABLE P/N VXH42(19).
2C6LSNH
NUMBER & CIRCUIT CONDUCTOR SIZE 2C/#6 AWG, AVERAGE INSULATION
THICKNESS 45 MILS, AVERAGE JACKET THICKNESS 60 MILS, NOMINAL
CABLE O.D. 0.775 IN,NOMINAL CABLE WEIGHT 378 LBS/1000 FT.
MULTI-CONDUCTOR, 600V, HEAT, MOISTURE AND SUNLIGHT RESISTANT,
BLACK, POLYOLEFIN OR EQUIVALENT LOW SMOKE HALOGENATED
INSULATING MATERIAL. WET OR DRY LOCATION AT 90 DEGREES C.
PART # DRAKA 382559
2C6T6V
TWO CONDUCTORS, #6AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, UNSHIELDED, TRAY CABLE, 90 DEGREE C, 600V,
0.645" O.D., ANIXTER CAT. #3G-0602.
1F
2C6T6VOS
TWO COPPER CONDUCTORS, #6AWG, TYPE C STRANDED (19 STRANDS)
XLPE,BLACK,SHIELDED, UV RESISTANT (SUN RESISTANT),
90 DEGREES C, 600V,0.775 O.D. WIRE(CU) O.D.0.275.
1F
2C8T6V
TWO CONDUCTORS, #8AWG, STRANDED PVC/NYLON PVC CONTROL
CABLE, UNSHIELDED TRAY CABLE, 90 DEGREE C, 600V, 0.567"
O.D., ANIXTER CAT. #3G-0802.
1F
2C8TLN
TWO CONDUCTOR,#8 AWG, 19 STRAND,SHIELDED,90DEG.C,TC,
LOW SMOKE NON-HALOGENATED(LSNH),WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE (XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN(XLPO)JACKET,600V. 0.630" O.D.,
DRAKA CABLETEQ P/N LATER,MANCO PART # D88930208, Quote
# TCP8893 LAKE CABLE P/N VXH82S(19),(W/DRAIN WIRE)
2C8TLNU
TWO CONDUCTOR,#8AWG,600V,19 STRAND,UNSHIELDED,90DEG.C,TC,
LOW SMOKE NON-HALOGENATED(LSNH),WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN(XLPO)JACKET, 0.597" O.D., NO DRAIN
WIRE. LAKE CABLE P/N VXH82(19).
2C8TYR
TWO CONDUCTORS, TYREX SO, 600V, #8AWG, STRANDED,
COPPER WIRE, 0.70" O.D., STANDARD WIRE & CABLE CO.
CAT. #705-5. NOT FOR CABLE TRAY USE.
8/8/2011
1C
TERM.TYPE
(See Table 3)
LR6#10S
LR8-6, PS50/2
49
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
2C10T6V
TWO CONDUCTORS, #10AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, UNSHIELDED, TRAY CABLE, 90 DEGREE C,
0.262 X 0.431" O.D.,600V ANIXTER CAT. #2A-1002.
2C10TC
TWO CONDUCTORS, #10AWG,600V,CONTROL TRAY CABLE.
O.47" O.D. OKONITE CAT#202-10-4502.
2C10TLN
TWO CONDUCTOR,#10 AWG, 19 STRAND,SHIELDED,90DEG. C, TC,
LOW SMOKE NON-HALOGENATED (LSNH), WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE (XLPE) INSULATED CIRCUIT
CONDUCTORS AND CROSS-LINKED POLYOLEFIN (XLPO) JACKET,
600V 0.5" O.D. LAKE CABLE P/N VXH102S(19). (W/DRAIN WIRE)
2C10TLNU
TWO CONDUCTOR,#10AWG,600V,19 STRAND, UNSHIELDED, 90DEG. C, TC,
LOW SMOKE NON-HALOGENATED(LSNH),WITH THERMOSETTING CROSS-LINKED
POLYETHYLENE (XLPE) INSULATED CIRCUIT CONDUCTORS AND
CROSS-LINKED POLYOLEFIN(XLPO)JACKET,0.449" O.D., NO DRAIN WIRE,
LAKE CABLE P/N VXH102(19).
2C10TYR
TWO CONDUCTORS, TYREX TYPE SO, 600V, #10AWG,
STRANDED, COPPER WIRE 0.640" O.D., STANDARD WIRE &
CABLE CO. CAT. #703-26. NOT FOR CABLE TRAY USE.
1A
LSY#8, STRIP
2C12OS
TWO CONDUCTORS, #12AWG, STRANDED, 600V, WITH OVERALL
SHIELD AND JACKET, TYPE SJO500, PER MIL-C-3432D, C0-02-MFG
(2/12) SJO500, 0.50" O.D.
1A
LRY#6, PPR8
2C12RR
TWO CONDUCTORS, #12AWG, RADIATION RESISTANT,
INDIVIDUAL WIRE. BAY ASSOCIATES MIL-16878/15-12. STYLE 3271.
2C12TC
TWO CONDUCTORS, #12AWG, 600V, CONTROL TRAY CABLE.
0.42" O.D. OKONITE CAT#202-10-4402.
2C12T6V
TWO CONDUCTORS, #12AWG, UNSHIELDED, STRANDED,
PVC/NYLON CONTROL CABLE TRAY CABLE, 90 DEGREE C, 600V,
0.227 X 0.361" O.D., ANIXTER CAT. #2A-1202.
2C12TEF
TWO CONDUCTORS, #12AWG, TINNED COPPER, TEFLON
INSULATED. CONDUCTORS CABLED. BELDFOIL ALUMINUM.
POLYESTER SHIELD TEFLON JACKET, RED TINT. NEC ARTICLE
760. PLENUM-POWER LIMITED. 0.303"O.D. BELDEN P/N83802.
8/8/2011
1B
MS8RPA
1B
50
CABLE TYPE
CABLE DESCRIPTION
2C12TLN
TWO CONDUCTORS,#12AWG, TYPE C STRAND, 90DEG. C, TC,
LOW SMOKE NON-HALOGENATED(LSNH), WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT
CONDUCTORS AND CROSS-LINKED POLYOLEFIN (XLPO)
JACKET, 600V 0.415" O.D.,DRAKA CABLETEQ PART# LATER,
MANCO PART # D88930212, Quote # TCP8893
2C12TLNU
TWO CONDUCTOR,#12AWG,600V,19 STRAND,UNSHIELDED, 90DEG. C,
TC, LOW SMOKE NON-HALOGENATED (LSNH),WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN(XLPO)JACKET,0.394" O.D.,
NO DRAIN WIRE. LAKE CABLE P/N VXH122(19).
2C12TYR
TWO CONDUCTOR, TYREX TYPE SO, 600V, #12AWG,
STRANDED, COPPER WIRE 0.605" O.D., STANDARD WIRE &
CABLE CO. CAT. #703-20 NOT FOR CABLE TRAY USE.
2C14OS
TWO CONDUCTORS, #14AWG, OVERALL SHIELDED.
2C14TYR
TWO CONDUCTORS, TYREX TYPE SO, 600V, #14AWG,
STRANDED COPPER WIRE 0.53" O.D., STANDARD WIRE &
CABLE CO. CAT. #703-14. NOT FOR CABLE TRAY USE.
2C16T3V
TWO CONDUCTORS, #16AWG, 300V. MFR: BELDEN.
2C16T6V
TWO CONDUCTORS, #16AWG, 600V, 19 TC STRANDS,
TRAY CABLE. 0.301" O.D. BELDEN CAT#9487.
2C18OTN
TWO CONDUCTORS, 18 AWG, SHIELDED, LOW SMOKE ZERO
HALOGEN, 300V, TRAY CABLE, O.D. 0.313 IN., LAKE CABLE
P/N: TXH182S.
2C18TC
TWO CONDUCTORS, #18AWG, TRAY CABLE.
8/8/2011
See color
CODE TABLE
TERM.TYPE
(See Table 3)
1A
LFY, STRIP
LSY#8,MS8PAR,
LRY#8
1A
LRB#6, STRIP
51
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
2C18TLN
TWO CONDUCTORS,18AWG,19 STRAND,OVERALL SHIELD,TRAY CABLE,
600V CONDUCTOR,18 AWG TIN COATED COPPER. CLASS B
STRANDING PER ASTM B8 INSULATION. CROSS-LINKED
POLYETHYLENE(XLPE).COLOR CODE: ONE BLACK AND
ONE WHITE. CONDUCTOR SHIELD: BRAIDED TIN COATED
COPPER SHIELD OVER INDIVIDUAL PAIRS. COLOR CODE:
METHOD 2(OVER COMP SHIELD).JACKET: LOW SMOKE,
ZERO-HALOGEN CROSS-LINKED POLYOLEFIN(LSZH XL POLYO).
BLACK (BLK) OR WHITE (WHT) CABLES ARE 75 OHM INDIVIDUALLY
SHIELDED. MULTI-PAIR CONSTRUCTIONS SUITABLE FOR WATERTIGHT,
NON-FLEXING SERVICE. MIL-C-24643/33, TYPE LS2SWU-1,
O.D.=0.295. LAKE CABLE P/N VXH182S(19) (W/DRAIN WIRE)
2C18TLNU
TWO CONDUCTOR,#18AWG,600V,19 STRAND,UNSHIELDED, 90DEG. C,
TC, LOW SMOKE NON-HALOGENATED (LSNH),WITH THERMOSETTING
CROSS-LINKED POLYETHYLENE(XLPE)INSULATED CIRCUIT CONDUCTORS
AND CROSS-LINKED POLYOLEFIN(XLPO)JACKET,0.305" O.D.,
NO DRAIN WIRE. LAKE CABLE P/N VXH182(19).
2C20OS
TWO CONDUCTORS, #20AWG, 300V, STRANDED TINNED
COPPER CONDUCTORS, OVERALL SHIELDED, PVC JACKET,
0.18" O.D., ALPHA CAT#2412.
2C20OSTC
TWO CONDUCTORS # 20AWG OVERALL SHIELDED, TRAY RATED
CABLE, STRANDED COPPER WIRE, 300V, UV RESISTANT,
0.207" O.D., PLTC CABLE ALPHA, ID SWITCH.
CAT # 5610B2001E OR EQUAL.
2C20RR
TWO CONDUCTOR, #20AWG, STRANDED, RADIATION AND
CORROSION, RESISTANT FLAME RETARDANT, NON-PVC, ITTSURPRENANT XML-SERIES, 600VAC ARE TWISTED TOGETHER
USING SLAC S/N61-328-316-01 BLACK AND SLAC S/N61-328-316-10
WHITE. 0.10" O.D.
1F
SOLDER
2C22MS
TWO CONDUCTORS, MICROPHONE CABLE, #22AWG,
STRANDED, TINNED-COPPER WIRE, OVERALL SHIELD WITH DRAIN
WIRE, 0.23" O.D., BELDEN CAT. #8422
1U
LSR#6, TT4P,
TT4S, TT8S
MS3P, MS3S,
LFR, LEMO-A,LRR#6
2C22OLN
TWO CONDUCTOR,22 AWG, SHIELDED, LOW SMOKE NON-HALOGEN,
CABLE TRAY RATED.0.190” O.D.,LAKE CABLE P/N: TXH222S.
8/8/2011
52
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
2C22OS
TWO CONDUCTORS OVERALL SHIELDED, #22AWG
THERMOCOUPLE. HAL 10443P. EX PP-K-20S-TWSH-SLE.
OMEGA ENGINEERING.
2C250LV
TWO(250Kcmil)CABLES, EP INSULATION/HYPALON JACKET,
90deg.DRY/75deg.WET, 600V, 0.96" O.D., ANIXTER CAT#3BF-2501
OR EQUIVALENT.
2C500TLS
PARALLEL RUN OF 2 SINGLE CONDUCTOR 500KCMIL, FLEX,
90DEG/105DEG. C, TC,LOW SMOKE NON-HALOGEN, (LSNH) 600V.
INSULATION COLOR GRAY, 1.150IN O.D.WT= 1.775LB/FT AMERICAN
P/N 39778. AMERICAN INSULATED WIRE CORP P/N 39914 BLACK
INSULATION.
2MTW-B
ONE CONDUCTOR, #2AWG, STRANDED, WIRE TYPE MTW, BLACK,
TFF, AWM, TEW, 600V, 500 FEET SPOOL.
2PR16AS
TWO PAIRS, #16AWG, CLX CABLE, OVERALL SHIELDED.
MFR: OKONITE.
2PR16IS
TWO PAIRS, #16AWG, INDIVIDUAL SHIELDED AND OVERALL
SHIELD, STRANDED TINNED COPPER, 300V, TRAY CABLE, ANIXTER
P/N 323-231-1602.
1A
2PR18OS
TWO TWISTED PAIRS, #18AWG, STRANDED, OVERALL
SHIELD, 300V, TRAY CABLE, 0.397" O.D., BELDEN CAT. #9552.
1F
2PR18IS
TWO PAIRS, #18AWG, INDIVIDUAL SHIELDED.
2PR20IS
TWO TWISTED PAIRS, #20AWG, STRANDED, INDIVIDUALLY
SHIELDED, WITH #22 AWG DRAIN WIRE, 300 VOLT, CM RATED,
0.30" O.D., BELDEN P/N 9402.
1S
2PR20OS
TWO PAIRS, #20 AWG, 300V, OVERALL SHIELDED, TRAY
CABLE, 0.27" O.D., ALPHA CAT. #45452.
1H
2PR20OTN
TWO PAIRS, #20 AWG, 300V, OVERALL SHIELDED, TRAY CABLE,
LOW SMOKE ZERO HALOGEN, 0.27” O.D.
LAKE CABLE P/N: TXH202PRS.
1H
2PR20SCC
TWO RUNS OF 1PR20SCC.
8/8/2011
TERM.TYPE
(See Table 3)
LB60D8, LB60-8
LFR, TT8S
53
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
2PR22IS
TWO TWISTED PAIRS, #22AWG, STRANDED, INDIVIDUALLY
SHIELDED,WITH #24 AWG STRANDED COMMON DRAIN WIRE, 300
VOLT, 0.16" O.D., CM RATED, BELDEN P/N 8723.
SLAC SN61-329-314-02.
1S
LFR
2PR22OS
TWO TWISTED PAIRS, 300V, #22AWG, STRANDED, COPPER
WIRE, OVERALL SHIELD WITH DRAIN WIRE, 0.31" O.D. TRAY CABLE.
1F
LSR, TT4S
DB9P AMP4P,AMP4S
2PR22OTN
2 PAIR, 22 AWG STRANDED CABLE, OVERALL SHIELD WITH
DRAIN WIRE AND LSZH JACKET, LAKE CABLE P/N TXH222PRS.
2PR22SS
TWO PAIR, #22AWG, SOLID CONDUCTORS, 300V, 0.168"
O.D., CM RATED, BELDEN CAT. #8795.
2PR22TX2
FOUR CONDUCTORS, #22AWG, STRANDED, TWISTED PAIRS,
INDIVIDUALLY SHIELDED, WITH #24AWG STRANDED TC DRAIN WIRE,
300 VOLT, 0.196" O.D., BLACK LSZH JACKET. BELDEN PN# 8723SB.
2PR24IS
TWO PAIRS, STRANDED COPPER WIRE, INDIVIDUALLY
SHIELDED WITH ONE ISOLATED DRAIN WIRE PER PAIR, CHROME
PVC JACKET, 0.335"O.D., CM RATED BELDEN CAT-# 9729
'DATALENE' CABLE.
2PR24OS
TWO PAIRS, #24AWG, OVERALL SHIELDED, STRANDED TWISTED,
POLYETHYLENE INSULATED. TINNED COPPER, TRAY RATED.
BELDEN CAT#9842.
2PR28OS
TWO TWISTED PAIRS, #28AWG, STRANDED TINNED COPPER
DRAIN WIRE. OVERALL SHIELDED, 0.235" O.D., CHROME PVC
JACKET. BELDEN CAT#8132.
2SMMTLN
2-STRAND, 50/125UM, (550 METER 10-GBE), MULTI-MODE,
OPTICAL BREAKOUT CABLE. LOW-SMOKE, ZERO-HALOGEN
CABLE SUITABLE FOR TRAYS AND RISERS. AQUA OUTER JACKET.
OUTER DIAMETER: 7.8MM(.31"). SUB-CABLE DIAMETER: 2.5MM(.10").
MINIMUM INSTALLATION BEND RADIUS: 11.7CM(4.6").
MINIMUM LONG-TERM BEND RADIUS: 7.8CM(3.1").
OPTICAL CABLE CORPORATION PART NUMBER: BX002ZALE9QZ
8/8/2011
1c
1P
DAY-20, MS6S
MS6PR, LFR
RTDS
54
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
2SSMTLN
2-STRAND, 9/125UM, SINGLE-MODE, OPTICAL BREAKOUT CABLE.
LOW-SMOKE, ZERO-HALOGEN CABLE SUITABLE FOR TRAYS AND RISERS.
YELLOW OUTER JACKET. OUTER DIAMETER: 7.8MM(.31").
SUB-CABLE DIAMETER: 2.5MM(.10"). MINIMUM INSTALLATION BEND
RADIUS: 11.7CM(4.6"). MINIMUM LONG-TERM BEND RADIUS: 7.8CM(3.1").
OPTICAL CABLE CORPORATION PART NUMBER: BX002ZSLB9YZ
2THHN
ONE CONDUCTOR, #2 AWG, THHN, BLACK, 19 STRAND, 600V.
SLAC S/N 61-328-372-01.
2T1C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C1TLSNU.
2T2C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C2TLSNU.
2T4C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C4TLNU.
2T6VOJ
SLAC CABLE TYPE USED FOR CODING PURPOSE ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE 2C2TS6V.
2T8C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C8TLNU.
2T10C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C10TLNU.
2T18C1
SLAC CABLE TYPE USED FOR CODING PURPOSES ONLY. THE CONDUCTOR
BELONGS TO ONE PAIR CABLE AND IS USED TO CONNECT MAGNETS
IN SERIES. THIS PARTICULAR CONDUCTOR BELONGS TO SLAC TYPE
CABLE: 2C18OTN.
8/8/2011
TERM.TYPE
(See Table 3)
LB2-5
55
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
2.0HEL
1 5/8" HELIAX COAXIAL CABLE, FOAM DIELECTRIC, STANDARD JACKET,
50 OHMS,1.98" OD, COPPER CONDUCTOR, ANDREW TYPE LDF7-50A.
BCS MPS PLIC
3C2T6V
THREE CONDUCTORS, #2AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, UNSHIELDED, TRAY CABLE, 90 DEGREE C,
600V, 0.947" O.D., ANIXTER CAT. #3G-0203
3C4IW
THREE CONDUCTORS, #4AWG INDIVIDUAL WIRE.
3C8T6V
THREE CONDUCTORS, #8AWG, 600V, PVC JACKET. STRANDED
COPPER WIRES. 0.600" O.D. TRAY CABLE. ANIXTER #3G-0803.
3C10PVC
THREE CONDUCTORS, PVC JACKET AND INSULATION, 600V, #10 AWG,
FLEXIBLE STRANDED COPPER WIRE, LAPPUSA OLEFLEX 190
P/N 601003 NOT FOR CABLE TRAY USE
3C10STOW
THREE CONDUCTORS, PVC JACKET AND INSULATION TYPE STOW,
600V, #10 AWG,FLEXIBLE STRANDED COPPER WIRE, COLEMAN
CABLE P/N 20039 NOT FOR CABLE TRAY USE.
3C10TYR
THREE CONDUCTORS, TYREX TYPE SO, 600V, #10 AWG,
STRANDED,COPPER WIRE, 0.69" O.D., SLAC SN61-329-722-42.
NOT FOR CABLE TRAY USE.
3C12FLX
THREE CONDUCTORS, #12AWG, 600V, MFR: AMERICAN
FLEX CONDUIT.
3C12G
THREE CONDUCTORS,#12 AWG, STRANDED, 600V INSULATION:
MATERIAL PVC,SHIELDED JACKETING: MATERIAL PVC, NOMINAL
O.D. (IN.) 0.395 ANIXTER PART # 2A-1203S
3C12OTN
THREE CONDUCTORS #12 AWG 19 STRAND, BARE COPPER, 600V,
90C XLPE JACKET LSNH, OVERALL SHIELD W/DRAIN, TRAY RATED.
LAKE CABLE VHX123S(19) O.D. 0.42"
3C12STOW
THREE CONDUCTORS, PVC JACKET AND INSULATION TYPE STOW, 600V,
#12 AWG,FLEXIBLE STRANDED COPPER WIRE, COLEMAN CABLE
P/N 20038 NOT FOR CABLE TRAY USE
3C12TYR
THREE CONDUCTORS, TYREX TYPE SO, 600V, #12 AWG,
STRANDED, COPPER WIRE, 0.635" O.D. SLAC SN61-329-722-32
NOT FOR CABLE TRAY USE
8/8/2011
TERM.TYPE
(See Table 3)
N-PLIC
1C
1C
LFY,LRY#6,LRY#10
56
CABLE TYPE
CABLE DESCRIPTION
3C12T3V
THREE CONDUCTORS, #12AWG, UNSHIELDED, 300V, PVC
JACKET, CL-2 RATED ALPHA CAT # 1892/3C, 0.32" O.D. COLOR
CODE IS BLACK, RED AND WHITE.
3C12T6V
THREE CONDUCTORS, #12AWG, 600V, 0.381" O.D.,
PVC JACKET. ANIXTER CAT#2A-1203.
3C14FLX
THREE CONDUCTORS, #14AWG, 600V, SOLID COPPER,
GROUND WIRE,TRAY CABLE, FLEXIBLE SHEATH, MFR. AMERICAN
FLEXIBLE CONDUIT CO. #14/2MC, 0.50" O.D.
3C14IW
THREE CONDUCTORS, #14AWG, INDIVIDUAL WIRE.
3C16FLX
THREE CONDUCTORS, #16AWG, COPPER. MFR: AMERICAN FLEX.
3C16T3V
See color
CODE TABLE
TERM.TYPE
(See Table 3)
1L
JAE4P, S&T
1C
ACP, ACR
THREE CONDUCTORS, 300V, #16AWG, STRANDED, TINNED
COPPER WIRE,TRAY CABLE, UNSHIELDED, PVC JACKET, 0.28"
O.D., ALPHA P/N 45073
1L
LFB, MS5S
MS8S,ACP,
ACJBX, LSB#8
3C16OS
THREE CONDUCTOR, #16 AWG, STRANDED, OVERALL SHIELD, 600V,
TRAY CABLE PVC JACKET, 0.40" O.D., ALPHA CAT. #45440/3.
1N
S&T
3C16TYR
THREE CONDUCTORS, TYREX TYPE SO, 600V, #16 AWG,
STRANDED, COPPER WIRE, 0.43" O.D., SLAC SN 61-329-722-12.
NOT FOR CABLE TRAY USE
1C
LFB,LSB#6
ACP, ACJBX,
ACR, LSR#6
3C18OS
THREE CONDUCTOR, #18 AWG, THERMOPLASTIC RUBBER JACKET,
300V OVERALL SHIELDED, TRAY CABLE, 0.256" O.D., ALPHA
CAT. #45383.
1L
LFR, LSR#8
3C18TLN
THREE CONDUCTORS, 18 AWG OVERALL SHIELD, LOW SMOKE ZERO
HALOGEN,TRAY CABLE CONDUCTOR 14 AWG AND SMALLER-TIN COATED
COPPER PER ASTM B286.
• CROSS-LINKED POLYETHYLENE (XLPE)
• COLOR CODE: METHOD 3 SHIELD:
• BRAIDED TIN-COATED COPPER JACKET
• LOW-SMOKE, ZERO-HALOGEN CROSS-LINKED
POLYOLEFIN (LSZH XL POLYO) BLACK (BLK) OR WHITE (WHT)
CABLES ARE MULTI-CONDUCTOR,
SHIELDED CONSTRUCTIONS, SUITABLE FORN NON-WATERTIGHT,
NON-FLEXING SERVICE.
• MILITARY P/N M24643/43-12UO, TYPE LS3SJ-18,O.D.=0.308
8/8/2011
57
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
3C18TYR
THREE CONDUCTOR, #18 AWG, TYREX TYPE SO, 600V,
STRANDED WIRE & CABLE CAT.#-703-4, 0.405" O.D. NOT
FOR CABLE TRAY USE.
1C
3C20OS
THREE CONDUCTOR, #20 AWG, 300V, OVERALL SHIELDED, CM
RATED, 0.218" O.D., BELDEN CAT. #8772.
1U
3C20T3V
THREE CONDUCTORS, 300V, #20 AWG, STRANDED, TINNEDCOPPER WIRE, TRAY CABLE , UNSHIELDED, PVC JACKET, 0.22"
O.D., ALPHA CAT.#45053.
1L
3C22OS
THREE CONDUCTORS, #22 AWG, STRANDED, OVERALL SHIELD,
300V, THERMOPLASTIC RUBBER JACKET, TRAY CABLE, 0.22"
O.D., ALPHA CAT.#45193.
1N
3PR16OS
THREE PAIR, #16 AWG, STRANDED, TRAY CABLE, OVERALL
SHIELD, 300V 0.36" O.D., BELDEN CAT. #1528A.
1F
MS5P, MS5S
3PR18OS
THREE PAIRS, #18 AWG, 300V TRAY CABLE, OVERALL
SHIELDED, STRANDED TINNED COPPER O.42" O.D., BELDEN
CAT.#9553.
1F
LFR, MS6S
3PR20IS
THREE PAIRS, DIGITAL DATA TRANSMISSION CABLE, #20
AWG, STRANDED, TINNED-COPPER WIRE, INDIVIDUALLY SHIELDED
PAIRS, WITH ONE ISOLATED DRAIN WIRE FOR EACH PAIR.
0.64" O.D., 110 OHMS, BELDEN SPECIAL.
1D
ST4, ST5, ST6
MS6P, MS6S
3PR20OS
THREE PAIRS, #20 AWG, STRANDED, COPPER WIRE,
OVERALL SHIELDED, TRAY CABLE, 300V, 0.31" O.D., ALPHA
CAT. #45453.
3PR22IS
THREE PAIRS, AUDIO AND DATA TRANSMISSION CABLE, #22
AWG, STRANDED, CM RATED, TINNED-COPPER WIRE,
INDIVIDUALLY SHIELDED PAIRS, WITH ONE ISOLATED DRAIN WIRE
FOR EACH PAIR, PVC JACKET, 0.3" O.D., BELDEN CAT. #8777.
3PR22ISH
3PR #22AWG, STRANDED COPPER WIRE, INDIVIDUALLY SHIELDED,
TEFLON INSULATED, WITH 1 ISOLATED DRAIN WIRE PER PAIR,
CHROME PVC JACKET, 300 VOLT, CM RATED, 0.345" O.D.,
'DATALINE' CONTROLLED IMPEDANCE CABLE BELDEN CAT#82777.
3PR22OS
THREE PAIRS, #22 AWG, STRANDED, COPPER WIRE,
OVERALL SHIELDED, TRAY CABLE, 300V, 0.326" O.D., BELDEN
CAT. #9513.
8/8/2011
MS3S-S, LFR
LFR, MS3S
1D
1F
LFR, LFB
MS6PB, MS6PA
MS8S, MS10S
58
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
3PR24CB
THREE TWISTED PAIRS, #24 AWG STRANDED TINNED COPPER
DRAIN WIRE, FEP TEFLON INSULATED, OVERALL BELDFOIL
ALUMINUM-POLYESTER SHIELD, 300V RMS, 0.241 O.D.,
BELDEN CAT.#88103.
3PR24IS
3 PAIR, #24 AWG, STRANDED, COPPER WIRE, INDIVIDUALLY
SHIELDED, WITH 1 ISOLATED DRAIN WIRE PER PAIR, CHROME PVC
JACKET, 300 VOLT, CM RATED 0.345" O.D., 'DATALENE
CONTROLLED IMPEDANCE CABLE, BELDEN CAT. #9730
SLAC SN 61-329-200-03.
1P
MS6PSB, TT8P
DAY-20, TT8PR
TT12P, MS6P
DB15P
3PR24OS
THREE PAIRS, #24 AWG, 300V, OVERALL SHIELDED,
STRANDED TINNED COPPER, TWISTED PAIRS, 0.27" O.D., TRAY
CABLE, ALPHA CAT. #45493.
1H
LFR, BSR
3PR24PLN
THREE PAIR #24 AWG. PLENUM CABLE NEC 725, BARE
COPPER CONDUCTORS WITH TINNED DRAIN. 0.167" O.D.
MFG. ALPHA P/N#57603.
3PR28OS
THREE PAIR, #28 AWG, STRANDED TINNED COPPER WIRE,
OVERALL SHIELD, TRAY CABLE, 0.260" O.D., BELDEN CAT. #8133.
3TT22OS
COMPUTER CABLE,3 CONDUCTORS,22AWG GAUGE,300V,80DEGC
TEMPERATURE CHROME COLOR, S-R PVC INSULATION,30AWG,
7 STRANDING, 0.202 IN. OUTER DIAMETER, POWER ELECTRONIC
CABLE TYPE. BELDEN #9939 3C22OS(RS232)
350TLSNH
350KCMIL, 90DEG/105DEG. C, TC, LOW SMOKE NON-HALOGEN (LSNH),
600V.INSULATION COLOR GRAY, 0.990" O.D., WT= 1.3LB/FT,
AMERICAN PART # 39777. AMERICAN INSULATED WIRE CORP P/N 39780
(BLACK INSULATION).
373FLX
MINIMUM WIRES PER CONDUCTOR 925,NOMINAL INSULATION THICKNESS
IN 0.075, NOMINAL JACKET THICKNESS IN 0.065, NOMINAL OUTSIDE
DIAMETER IN 1.110, APPROX. WEIGHT LBS. PER 1,000 FT. 1436,
AMPACITY 90DEG. 591, EXTRA FLEXIBLE CABLE, 325 STRANDS, 600V,
0.65" O.D., PART # AMERCABLE 37-119-217 ID 1.110"
PLEASE SEE GENERAL NOTES # 8
4C2/0OS
FOUR CONDUCTORS, #2/0 AWG, TYPE MC(XHHW), 600V,
TRAY CABLE,1.32" O.D., ALUMINUM SHEATH.OKONITE CAT.#571-31-3289.
8/8/2011
LB35-9,LB35-10
LB35D9
LB02-6, LB02DB
59
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
4C2AS
OKONITE C-L-X® TYPE MC-HL (XHHW-2) 600V POWER CABLE WITH
ALUMINUM SHEATH. FOUR COPPER CONDUCTORS/90°C WET OR DRY RATING
FOR CABLE TRAY USE. OKONITE PART NUMBER 571-31-3276.
4C2NS
OKONITE C-L-X® TYPE MC-HL (XHHW-2) 600V POWER CABLE
WITH-OUT ALUMINUM SHEATH FOUR COPPER CONDUCTORS/90°C WET
OR DRY RATING FOR CABLE TRAY USE.
OKONITE PART NUMBER 571-31-3276
4C6PVC
FOUR CONDUCTORS, #6 AWG, PVC JACKET AND INSULATION, 600V,
FLEXIBLE STRANDED COPPER WIRE. O.D. 0.986"
MFG: LAPPUSA, OLEFLEX 190. P/N: 600604.
NOT FOR CABLE TRAY USE
4C8AS
FOUR CONDUCTORS, #8 AWG, 600V, ALUMINUM SHEATH, TRAY
CABLE, OKONITE CLX TYPE MC (XHHW), CAT-# 571-31-3264,
0.95" O.D.
4C8SHLD
OKONITE C-L-X® TYPE MC-HL (XHHW-2) 600V POWER CABLE WITH
ALUMINUM SHEATH FOUR COPPER CONDUCTORS/90°C WET OR DRY RATING
FOR CABLE TRAY USE.OKONITE PART NUMBER 571-31-3263
4C8T6V
FOUR CONDUCTORS, #8 AWG, STRANDED, PVC/NYLON PVC
CONTROL CABLE, 0.658" O.D., TRAY CABLE, UNSHIELDED,
90 DEGREE C, 600V, ANIXTER CAT. #3G-0804.
1F
4C8TYR
FOUR CONDUCTOR, TYREX TYPE SO, 600V, #8 AWG,
STRANDED, COPPER WIRE, 0.82" O.D., STANDARD WIRE &
CABLE CO. CAT. #705-15. NOT FOR CABLE TRAY USE.
1A
LR8U10, ACP20
4C10FST
FOUR CONDUCTOR, PVC FLAT FESTOON CABLE, 600V, #10 AWG.
4C10T6V
FOUR CONDUCTORS, #10AWG, STRANDED, TRAY CABLE,
600V, 0.556" O.D., UNSHIELDED, ANIXTER CAT. #2MR-1004.
1B
MS8PA, MS8SA
MS8PW, MS8PY, LRY#6R
4C10TYR
FOUR CONDUCTOR, TYREX TYPE SO, 600V, #10 AWG,
STRANDED, COPPER WIRE, 0.745" O.D., STANDARD WIRE &
CABLE CO. CAT. #703-30. NOT FOR CABLE TRAY USE.
1A
4C12OJ
4 CONDUCTORS, #12 STRANDED, OVERALL JACKET, UNSHIELDED
WIRES COLORED:BLACK, RED, BLUE, WHITE. SPECIAL CABLE FOR
LINAC CORRECTORS.
8/8/2011
1B
LR8U10
60
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
4C12PVC
FOUR CONDUCTORS, #12 AWG, PVC JACKET AND INSULATION, 600V,
FLEXIBLE STRANDED COPPER WIRE. O.D. 0.460"
MFG: LAPPUSA, OLEFLEX 190. P/N: 601204.
NOT FOR CABLE TRAY USE
4C12T6V
FOUR CONDUCTORS, #12AWG, STRANDED, TRAY CABLE,
600V, 0.468" O.D., UNSHIELDED, ANIXTER CAT.#2MR-1204.
1B
MS8PA, MS8SA
MS8PW, MS8PY, LRY#6R
4C12TYR
FOUR CONDUCTOR, #12 AWG, TYREX TYPE SO, 600V,
STRANDED, COPPER WIRE, 0.665 O.D., STANDARD WIRE &
CABLE CO. CAT. #703-24. NOT FOR CABLE TRAY USE.
1A
LRY#10
4C14IW
FOUR CONDUCTORS, #14AWG, INDIVIDUAL WIRE.
4C16FLX
FOUR CONDUCTORS, #16 AWG, 600V, SOLID COPPER,
GROUND WIRE, TRAY CABLE, FLEXIBLE SHEATH, MFR. AMERICAN
FLEXIBLE CONDUIT CO., 0.5" O.D.
1Q
4C16OS
FOUR CONDUCTORS, #16 AWG, STRANDED, COPPER WIRE,OVERALL
SHIELD, TRAY CABLE, 300V, 0.31" O.D., ALPHA NO. #45364.
1L
4C16PLEN
FOUR CONDUCTORS, #16 AWG, PLENUM CABLE, TINNED COPPER
CONDUCTORS, TEFLON INSULATED, BELDFOIL ALUMINUMPOLYESTER SHIELD WITH 85% TINNED COPPER BRAID SHIELD.
TEFLON JACKET. NEC 800. 0.228"O.D., BELDEN P/N 83704.
2
4C16S/U
FOUR CONDUCTOR, #16 AWG, TWO CONDUCTORS ARE
INDIVIDUALLY SHIELDED AND THE OTHER TWO CONDUCTORS ARE
NOT SHIELDED, 0.5" O.D.
4C16T3V
FOUR CONDUCTOR, #16 AWG, TRAY CABLE, 300V,
STRANDED TINNED COPPER WIRE, UNSHIELDED, 0.44" O.D.,
ALPHA CAT. #45074.
4C16T6V
FOUR CONDUCTORS, #16AWG, TRAY CABLE, UNSHIELDED.
4C16TYR
FOUR CONDUCTORS, TYREX TYPE SO, 600V, #16 AWG,
STRANDED, COPPER WIRE, 0.485" O.D., STANDARD WIRE &
CABLE CO.CAT. #703-12. NOT FOR CABLE TRAY USE.
1A
4C18OS
FOUR CONDUCTORS, #18 AWG, STRANDED, COPPER WIRE,
OVERALL SHIELD, TRAY CABLE, 300V, 0.27" O.D., ALPHA NO.
#45384.
1L
8/8/2011
LFB & BULLET
1L
LFB
BULLET
61
CABLE TYPE
CABLE DESCRIPTION
4C18TEF
FOUR CONDUCTORS, #18 AWG, TINNED COPPER, TEFLON
INSULATED, OVERALL TAPE WRAP, 0.167 O.D., BELDEN CAT.#88489.
4C20OS
FOUR CONDUCTORS, #20 AWG, STRANDED, COPPER WIRE,
OVERALL SHIELD, TRAY CABLE, 300V, 0.25" O.D., ALPHA NO.
#45464.
4C20OTN
FOUR CONDUCTORS, 20 AWG, SHIELDED, LOW SMOKE ZERO HALOGEN,
300V, TRAY CABLE, O.D. 0.234 IN., LAKE CABLE P/N: TXH204S.
4C22
FOUR CONDUCTORS ENCASED IN RADIATION RESISTANT SPIRAL WRAP.
THE SPIRAL WRAP IS SPLIT LOOM TUBING, 0.25" O.D. METRA
PART#14. METRA - (800)271-0932, EXT. 249, SALES.
4C22OS
FOUR CONDUCTORS, #22AWG, 300V, TINNED COPPER, 2 SHIELDED
AND 2 UNSHIELDED CONDUCTORS. 0.165" O.D. BELDEN#8724.
4C22T6V
FOUR CONDUCTORS, #22AWG, TRAY CABLE, 600V, STRANDED TINNED
COPPER WIRE, UNSHIELDED, 0.295" O.D.
4MTW-B
ONE CONDUCTOR, #4AWG, STRANDED, WIRE TYPE MTW, BLACK,
TFF, AWM, TEW, 600V, 500 FEET SPOOL.
4PR16AS
FOUR PAIRS, ARMORED CABLE, 300V, #16 AWG, STRANDED,
TRAY CABLE TINNED COPPER WIRE, OVERALL SHIELD AND DRAIN
WIRE, O.82"O.D., OKONITE CLX TYPE P-OS 561-10-3404.
4PR16IS
FOUR PAIR, #16 AWG, INDIVIDUALLY SHIELDED, 600 VOLT,
TRAY CABLE 0.578" O.D., BELDEN CAT. #1039A.
4PR16OS
FOUR PAIR, #16 AWG, 600V, 0.558" O.D., OVERALL
SHIELD,TRAY CABLE BELDEN CAT. #1070A.
4PR16TC
FOUR PAIR, #16AWG, 600V, OVERALL SHIELDED. MFR: OKONITE.
4PR16TLN
FOUR PAIR, #16 AWG, 600 VOLT INDIVIDUALLY SHIELDED,
LOW SMOKE NON HALOGEN, TRAY CABLE, 0.610 O.D.,
LAKE CABLE # VXH164SPOS.
4PR18AS
FOUR PAIR ARMORED CABLE, 300V, #18 AWG, STRANDED
TINNED COPPER WIRE, OVERALL SHIELD WITH DRAIN WIRE, TRAY
CABLE, 0.82" O.D., OKONITE CLX TYPE SP-OS, OKONITE CAT
#561-10-3304.
8/8/2011
See color
CODE TABLE
TERM.TYPE
(See Table 3)
1L
LFR, TT4S
DAY20, MS10PA
1F
LFB, LFB-B,
LSB-G, WNY,
LSB#6, LRB#10
1F
1F
LRB#6, HR13S
1F
62
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
4PR18ITN
FOUR PAIR, # 18 AWG, INDIVIDUALY SHIELDED PAIRS WITH DRAIN
WIRE, BLACK AND WHITE NUMBERED PAIRS, TRAY CABLE, LOW SMOKE
ZERO HALOGEN, SUNLIGHT RESISTANT, OVERALL ALUM MYLAR SHIELDED.
0.418" O.D. MFG: LAKE CABLE, P/N: TXH184EPS.
4PR18OS
FOUR PAIR, #18 AWG, 300V, OVERALL SHIELD, STRANDED
TINNED COPPER, TRAY CABLE, BELDEN CAT. #9554. 0.458" O.D.
4PR18OTN
FOUR PAIR, # 18 AWG, 19 STRAND BARE COPPER WIRE. FLAME
RETARDANT CROSS LINKED PE INSULATION, OVERALL ALUM MYLAR
SHIELD, 18 AWG 7 STRAND TC DRAIN WIRE, BLACK ZERO HALOGEN
POLYOLEFIN JACKET. TYPE ITC. CABLES ALSO MEETS THE
REQUIREMENTS OF UL STANDARD 1685 FOR LIMITED SMOKE (UL)
LSZH LS LIST.0.415” O.D. LAKE CABLE P/N TXH184PRS(19).
4PR18TC
FOUR PAIR, #18AWG, TRAY CABLE.
4PR20IS
FOUR PAIR, #20 AWG, INDIVIDUALLY SHIELDED, STRANDED
TINNED COPPER, CL2 RATED, 30V, ETHERNET CABLE, 0.36"
O.D., BELDEN CAT.#9892.
1F
4PR20OS
FOUR PAIR, #20 AWG, OVERALL SHIELDED, STRANDED
TINNED COPPER, TRAY CABLE, 300V, 0.412" O.D., BELDEN CAT.
#1056A. WT= 0.097 LB/FT
1F
4PR22IS
FOUR PAIR, #22AWG, STRANDED TINNED COPPER,
INDIVIDUALLY SHIELDED, TRAY CABLE, 300V, 0.360" O.D.,
BELDEN CAT. #9330.
1F
4PR22ITN
FOUR PAIR, #22AWG, STRANDED TINNED COPPER, INDIVIDUALLY
SHIELDED, LOW SMOKE ZERO HALOGEN, 300V PLTC. 0.347” O.D.
WT=.074 LBS/FT. LAKE P/N 050731 SWC3.
4PR22OS
FOUR PAIR #22 AWG, STRANDED TINNED COPPER WIRE,
OVERALL SHIELD, 300V, TRAY CABLE, 0.353" O.D. BELDEN CAT#9514.
4PR24CC
FOUR TWISTED PAIRS, #24AWG, TINNED COPPER, INDIVIDUALLY
SHIELDED, CHROME PVC JACKET. 0.388" O.D. BELDEN#8164.
4PR24FRP
FOUR PAIR, #24AWG, TINNED COPPER, FOAMED TEFLON
INSULATED, TWISTED PAIRS, GRAY FLUOROCOPOLYMER JACKET,
300V RMS, 0.261"O.D. BELDEN CAT#88104.
8/8/2011
TERM.TYPE
(See Table 3)
1F
1F
LFR, TT8P
AMP8P, AMP8S
AMP9F
63
CABLE TYPE
CABLE DESCRIPTION
4PR24IS
FOUR PAIR, #24AWG, STRANDED COPPER WIRE,
INDIVIDUALLY SHIELDED, 300 VOLT, CM RATED, 0.363" O.D.,
BELDEN CAT. #9728, "DATALENE" CONTROLLED IMPEDANCE CABLE.
4PR24ITN
FOUR PAIR, 24AWG, STRANDED COPPER WIRE,
INDIVIDUALLY SHIELDED, 300 VOLT,
0-HAL BLK JACKET, CM RATED, 0.375" O.D.,
4PR24NS
FOUR PAIR, #24AWG, NO SHIELD. BELDEN CAT3, PVC JACKET,
TELEPHONE WIRE.
4PR24OS
FOUR PAIR, #24AWG, STRANDED COPPER WIRE, OVERALL
SHIELD, TRAY CABLE, 0.388" O.D., BELDEN CAT. #8164.
4PR350
FOUR PAIR TWISTED UNSHIELDED, #24 AWG, SOLID BARE COPPER,
FEP PVC INSULATED, CATEGORY 5, TRAY RATED, 0.188" O.D.,
350MHZ ETHERNET CABLE.
4PR350PLN
FOUR PAIR TWISTED UNSHIELDED, #24 AWG, SOLID BARE
COPPER, FEP TEFLON INSULATED, CATEGORY 5, TRAY RATED,
0.188" O.D., 350MHZ ETHERNET CABLE.
4-PACK
FOUR COAXIAL CABLES INSIDE A SINGLE JACKET WITH
CONNECTORS INSTALLED. THIS CABLE ASSEMBLY IS SUPPLIED BY
DESY FOR THE FFTB WPM'S. 0.6" O.D.
4PRCAT3
FOUR PAIR,#24AWG, PLENUM OR PVC CABLE, CATEGORY 3.
TELEPHONE CABLE.
4PRCAT5
FOUR PAIR, #24AWG, PLENUM CABLE, CATEGORY 5. DATA CABLES.
4PRPLEN
FOUR PAIR, #24 AWG, SOLID BARE COPPER, FEP TEFLON
INSULATION, CMP RATED, UNSHIELDED, PLENUM CABLE,
0.200" O.D., CATEGORY 5. BELDEN CAT. #1585A,YM28822.
4PRPLEN2
FOUR PAIR, #24AWG, 350mhz, BELDEN CAT#1585A.
4PRPVC
FOUR PAIR, #24 AWG, SOLID BARE COPPER, PVC
INSULATION, CMP RATED, UNSHIELDED CABLE, 0.217" O.D.,
CATEGORY 5. BELDEN CAT. #1583A, YM2881.
4PRPVC1
FOUR PAIRS, #24 AWG, WHITE, PVC JACKET, SOLID BARE
COPPER, UNSHIELDED, 0.217" O.D., CATEGORY 5, BELDEN
CAT. #1701A.
8/8/2011
See color
CODE TABLE
1P
TERM.TYPE
(See Table 3)
TT8P
NA
1b
1b
64
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
4SMMTLN
4-STRAND, 50/125UM, (550 METER 10-GBE), MULTI-MODE,
OPTICAL BREAKOUT CABLE. LOW-SMOKE, ZERO-HALOGEN CABLE
SUITABLE FOR TRAYS AND RISERS. AQUA OUTER JACKET.
OUTER DIAMETER: 9.1MM(.36"). SUB-CABLE DIAMETER: 2.5MM(.10").
MINIMUM INSTALLATION BEND RADIUS: 13.6CM(5.4").
MINIMUM LONG-TERM BEND RADIUS: 9.1CM(3.6").
OPTICAL CABLE CORPORATION PART NUMBER: BX004ZALE9QZ
4SSMTLN
4-STRAND, 9/125UM, SINGLE-MODE, OPTICAL BREAKOUT CABLE.
LOW-SMOKE, ZERO-HALOGEN CABLE SUITABLE FOR TRAYS AND RISERS.
YELLOW OUTER JACKET. OUTER DIAMETER: 9.1MM(.36").
SUB-CABLE DIAMETER: 2.5MM(.10"). MINIMUM INSTALLATION
BEND RADIUS: 13.6CM(5.4"). MINIMUM LONG-TERM BEND RADIUS: 9.1CM(3.6").
OPTICAL CABLE CORPORATION PART NUMBER: BX004ZSLB9YZ
4THHN
ONE CONDUCTOR, #4AWG, 7 STRAND,600V, SLAC S/N61-328-370-01
5C4IW
FIVE CONDUCTOR, #4AWG,COPPER CONDUCTORS, 19 STRANDS
PER CONDUCTOR, 600V, 90 DEGREES, TRAY RATED, XLPE BLACK
INSULATION, UV RESISTANT.MANCO: PART # MA0504GCT
5C4LSNH
NUMBER & CIRCUIT CONDUCTOR SIZE 5C/#4 AWG, AVERAGE
INSULATION THICKNESS 45 MILS, AVERAGE JACKET THICKNESS
80 MILS, NOMINAL CABLE O.D. 1.090 IN, NOMINAL CABLE WEIGHT
1011 LBS/1000 FT. MULTI-CONDUCTOR, 600V,HEAT, MOISTURE AND
SUNLIGHT RESISTANT, BLACK, POLYOLEFIN OR EQUIVALENT
LOW SMOKE ZERO HALOGENATED INSULATING MATERIAL, WET OR DRY
LOCATION AT 90 DEGREES C. PART # DRAKA 400288
5C8SO
FIVE CONDUCTORS, #8 AWG, TYPE SO/SOOW, 0.90” O.D.,600V,
SUPPLIER: ANIXTER, P/N: 4A-0805.
5C8TYR
PORTABLE POWER CABLE, ALPHA TYPE G, 4 CONDUCTOR WITH GROUND,
ALPHA PART NUMBER 7760 OR EQUIVALENT, 2KV, 45A, #8 AWG
NOT FOR CABLE TRAY USE.
5C10PVC
FIVE CONDUCTORS, PVC JACKET AND INSULATION, 600V, #10 AWG,
FLEXIBLE STRANDED COPPER WIRE, LAPPUSA OLEFLEX 190
P/N 601005 NOT FOR CABLE TRAY USE
5C10SO6V
FIVE COPPER CONDUCTOR #10AWG, TYPE SO, STRANDED (105 STRANDS),
SYNTHETIC RUBBER INSULATED, THERMOSET JACKETTED, 90 DEGREES
"C", 600V, 0.79 O.D., ANIXTER CAT # 4A-1005.
8/8/2011
TERM.TYPE
(See Table 3)
LRY#10
65
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
5C10TYR
FIVE CONDUCTORS, #10AWG, TYREX. SLAC S/N61-329-722-44
5C10T6V
FIVE CONDUCTOR, #10 AWG, 600V, UNSHIELDED, TRAY
CABLE, 0.615: O.D., ANIXTER CAT. #2MR-1005.
5C12TYR
FIVE CONDUCTORS, #12 AWG, 600V, TYREX TYPE SO,
STRANDED COPPER WIRE,NEOPRENE,105 DEGREE C RATED,
0.71" O.D., SLAC S/N 61-329-722-34. NOT FOR CABLE TRAY USE.
5C14IW
FIVE CONDUCTORS, #14AWG, INDIVIDUAL WIRE.
5C16OS
FIVE CONDUCTORS, #16 GAUGE, STRANDED, OVERALL FOIL
SHIELD, 600 V, TRAY CABLE, 0.48" O.D., ALPHA CAT. #45440/5.
1N
MS5S, TT4S
5C16T6V
FIVE CONDUCTORS, #16 AWG, 600 VOLT, TRAY CABLE,
STRANDED, UNSHIELDED, O.47" O.D., ALPHA P/N 45435.
1N
LFB, LFR
MS11S, LSB#6
5C16TYR
FIVE CONDUCTORS, TYREX TYPE SO, 600V, #16 AWG,
STRANDED TRAY CABLE, SLAC S/N61-329-722-14.NOT FOR CABLE
TRAY USE.
5C18TC
FIVE CONDUCTORS, #18AWG, 300V, STRANDED TINNED
COPPER CONDUCTORS, PVC JACKET. 0.26" O.D. ALPHA#1898/5.
5C18T6V
FIVE CONDUCTOR, #18 AWG, STRANDED, TRAY CABLE,
600V, UNSHIELDED, ALPHA CAT. #45425, 0.44" O.D.
1N
LFR, MS8P
5C20OS
FIVE CONDUCTOR, #20AWG, STRANDED, OVERALL SHIELD, 600V,
TRAY CABLE, 0.42" O.D., ALPHA CAT. #45420/5.
1N
LFR
5PR20OS
FIVE PAIR, #20 AWG, 300 VOLT, OVERALL SHIELD, TRAY
CABLE, 0.38" O.D., ALPHA CAT. #45455. IF EITHER END IS A
VAT7S CONNECTOR, BOTH ENDS ARE COLOR CODE: >>
1R,1H
VAT7S, MS8S
5PR22ITN
FIVE PAIR, #22 AWG, 7STR BARE COPPER WIRE WITH .021"
LSXLPE INSULATION, INDIVIDUAL SHIELDED WITH DRAIN WIRE,
300V, LOW SMOKE ZERO HALOGEN, TRAY CABLE, 0.471" O.D.,
BLK & WHT NUMBERED PAIRS. MFG: LAKE CABLE, P/N:TXH225EPS.
5PR22OS
FIVE PAIRS, #22 AWG, 300V, TRAY CABLE, OVERALL
SHIELDED, 0.30" O.D., ALPHA NO. 45495.
8/8/2011
LFY, LRY#8
1H
66
CABLE TYPE
CABLE DESCRIPTION
5PR24CB
FIVE PAIRS, #24AWG, TINNED COPPER, FEP TEFLON
INSULATION, GRAY FLUOROCOPOLYMER JACKET, 300V RMS,
0.269" O.D. BELDEN CAT#88105.
5PR24OS
FIVE TWISTED PAIRS, #24AWG STRANDED TINNED COPPER
DRAIN WIRE, OVERALL BELDFOIL ALUMINUM-POLYESTER SHIELD,
FEP TEFLON INSULATED, FLAME ARREST JACKET, 0.196" O.D.,
BELDEN CAT.#82505.
5PR28F
FIVE TWISTED PAIR, #28 AWG, TWIST'N'FLAT CABLE, LAMINATED
T'N'F, STYLE 2697, 300V, AMPHENOL SPECTRA-STRIP P/N
843-132-2801-010
5PR28OS
FIVE TWISTED PAIR, #28AWG, OVERALL SHIELD.
TINNED COPPER, CHROME PVC JACKET. 0.300" O.D.
BELDEN CAT#8135.
500TLSNH
500KCMIL,FLEX, 90DEG/105DEG. C, TC, LOW SMOKE NON-HALOGEN,
(LSNH)600V. INSULATION COLOR GRAY, 1.150" O.D.,WT=1.775LB/FT
AMERICAN P/N39778.AMERICAN INSULATED WIRE CORP P/N39914
(BLACK INSULATION)
6C14IW
SIX CONDUCTORS, #14AWG, INDIVIDUAL WIRE.
6C16OS
SIX CONDUCTORS, #16AWG, 300V, OVERALL SHIELDED,
0.35" O.D. ALPHA CAT#5366.
6C18TC
SIX CONDUCTORS, #18AWG, 300V, STRANDED TINNED
COPPER, TRAY CABLE, UNSHIELDED. PVC JACKET. 0.29" O.D.
ALPHA CAT#1898/6.
6C20OTN
SIX CONDUCTORS, 20 AWG, SHIELDED, LOW SMOKE ZERO
HALOGEN, 300V, TRAY CABLE, O.D. 0.283 IN.,
LAKE CABLE P/N: TXH206S.
6C26MLC
SIX CONDUCTORS, #26AWG, STRANDED FLAT MODULAR LINE CORD,
SPC TECHNOLOGY TYPE#8588-0182 STOCK #52N9472.
6PR16ITN
SIX INDIVIDUALLY SHIELDED PAIRS,#16AWG,600VOLT,UL
LISTED LSZH Type XLPE UL STANDARD 66,1277,1581,
NEC Type TC - TRAY RATED CABLE. LAKE CABLE
P/N VXH166EPS/20DR. .720 OD,266lb per 1000ft.
8/8/2011
See color
CODE TABLE
TERM.TYPE
(See Table 3)
DB9S
LB60D8, LB60-8
LB60S8, 500MSCI
67
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
6PR16OS
SIX PAIRS, #16 AWG, OVERALL SHIELD, 600 VOLT, TRAY
CABLE, 0.660" O.D., ANIXTER CAT. #2AS-1606POS.
6PR18IS
SIX PAIRS, #18 AWG, INDIVIDUALLY SHIELDED. BELDEN
CAT#9774. NEWARK 36F1395WA.
6PR18OS
SIX PAIRS, #18 AWG, OVERALL SHIELDED, 300V, TRAY
CABLE, 0.481" O.D., BELDEN CAT. #9556.
1F
6PR18T3V
SIX PAIR, #18 AWG, 300V, TRAY CABLE, UNSHIELDED,
0.45" O.D., ALPHA CAT. #45036.
1H
6PR20IS
SIX PAIR #20 AWG, 30V, INDIVIDUALLY SHIELDED,.427" O.D.
CM TYPE, COLOR CODE CHART NO. 3. ANIXTER/BELDEN CAT.# 9874
6PR20T3V
SIX PAIR, #20 AWG, 300V, TRAY CABLE, UNSHIELDED,
0.40"O.D., ALPHA CAT. #45286.
6PR22ITN
SIX PAIR, #22 AWG, INDIVIDUAL SHIELDED WITH DRAIN WIRE,
300V, LOW SMOKE ZERO HALOGEN, TRAY CABLE, 0.471" O.D.,
MFG: LAKE CABLE, P/N: TXH226EPS.
6PR22IS
SIX PAIR, #22 AWG, INDIVIDUAL SHIELDED, 300V, TRAY
CABLE,0.437: O.D., BELDEN CAT. #9331.
1D
6PR22OS
SIX PAIR, #22 AWG, STRANDED, OVERALL SHIELDED, 300
VOLT, TRAY CABLE 0.425" O.D., BELDEN CAT. #9516.
1F
LFR, MS8P
TT12S, DB-PS
6PR24IS
SIX PAIR, #24 AWG, STRANDED, COPPER WIRE,
INDIVIDUALLY SHIELDED, CM RATED 0.421" O.D.,ISOLATED
DRAIN WIRE PER PAIR, CHROME PVC JACKET, 300V, BELDEN CAT.
#9731, 'DATALENE' CONTROLLED IMPEDANCE CABLE.
1P
AMP24P
6PR24OS
SIX PAIR, #24 AWG, OVERALL SHIELD, TINNED COPPER,
S-R PVC INSULATED WITH OVERALL BELDFOIL SHIELD, PLUS
65% TINNED COPPER BRAID SHIELD, CHROME PVC JACKET,
0.311" O.D., MFG BELDEN, P/N #8336.
7C12T6V
SEVEN CONDUCTORS, #12AWG, 600V, 0.495" O.D., PVC JACKET.
MFR: ANIXTER.
7C18TC
SEVEN CONDUCTORS, #18AWG, 300V, STRANDED TINNED COPPER,
UNSHIELDED TRAY CABLE. PVC JACKET. 0.29" O.D.
ALPHA CAT#1898/7.
8/8/2011
1H
68
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
7C18T6V
SEVEN CONDUCTORS, #18 AWG, STRANDED, TRAY CABLE,
600V, 0.46" O.D., UNSHIELDED, ALPHA CAT. 45427.
1N
LFR, TT12S
7C22OS
SEVEN CONDUCTORS, #22 AWG, OVERALL SHIELD, 0.308" O.D.,
300V, SLAC PURCHASE SPECIFICATION #PS-114-001-03-R2.
1W
TT4P
7PR24IS
SEVEN PAIR, #24AWG, 150V, STRANDED, TINNED COPPER
WIRE, INDIVIDUALLY SHIELDED, PLENUM RATED, NEC CMP,
0.367" O.D., BELDEN CAT #89757.
7PR22OSS
SLAC MADE, 7 TWISTED PAIRS OF 22 AWG, TINNED
STRANDED COPPER. WIRES ARE TFE INSULATED (RED/WHITE).
WIRES ARE THEN WRAPPED IN STRANDED,TINNED COPPER
EXPANDABLE WIRE TUBES
(.38 DIAMETER TYP.- MIL-SPEC INC P/N 2146)AND
THEN WRAPPED IN STRANDED EXPANDABLE POLYETHYLENE TUBES
(ALTA TECH, 1" DIA PE FLEXIBLE TUBE).
8C10T6V
EIGHT CONDUCTORS, #10 AWG, STRANDED, TRAY CABLE,
0.682"O.D. UNSHIELDED, 600V, ANIXTER CAT. #2A-1008.
8C12TLN
EIGHT CONDUCTORS, 12AWG TC 600V 90C BARE COPPER WIRE,
FLAME RETARDANT PE INSULATION,NON-SHIELDED. BLACK
ZERO-HALOGEN POLYOLEFIN JACKET. CABLE MEETS REQUIREMENTS
OF UL STANDARD 1685 FOR LIMITED LOW SMOKE. UL LS LISTED.
LAKE CABLE P/N 03602WGP2. 0.72" O.D.
8C12T6V
EIGHT CONDUCTORS, TRAY CABLE, 600V, #12 AWG,
UNSHIELDED, 0.66" O.D., ANIXTER CAT. #2A-1208.
8C14IW
EIGHT CONDUCTORS, #14AWG, INDIVIDUAL WIRE.
8C16/3V
EIGHT CONDUCTORS, #16AWG, 300V, STRANDED TIN
COATED COPPER, UNSHIELDED. 0.41" O.D. ALPHA CAT#5078.
8C16T6V
EIGHT CONDUCTORS, #16AWG, TYPE TC.
8C18OS
EIGHT CONDUCTORS, #18AWG, 300V, STRANDED TIN
COATED COPPER,OVERALL SHIELDED.0.38" O.D. ALPHA CAT#5168.
8C20OS
EIGHT CONDUCTORS, #20AWG, 300V, STRANDED TIN
COATED COPPER,OVERALL SHIELDED.0.31" O.D.ALPHA CAT#5468.
8/8/2011
1B
1B
MS8PA,MS8PW
MS8PY, MS8SA,STRIP
69
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
8C22OS
EIGHT CONDUCTORS, #22AWG, STRANDED, 300V, OVERALL
SHIELDED. CHROME SILVER OUTER JACKET.SLAC S/N61-329-318-07.
8MTW-B
ONE CONDUCTOR, #8AWG, STRANDED, WIRE TYPE MTW, BLACK,
TFF, AWM, TEW, 600V, 500 FEET SPOOL.
8PR16AS
EIGHT PAIR, #16 AWG, ARMORED CABLE, 300V, OKONITE
CAT.#564-01-3408.
1F
8PR16IS
EIGHT PAIRS, #16 AWG, STRANDED, 300V, INDIVIDUALLY
SHIELDED, TRAY CABLE, 0.687" O.D., BELDEN CAT.#1494A.
1F
8PR16OS
EIGHT PAIRS, #16 AWG, STRANDED, OVERALL SHIELD, TRAY
CABLE, 300 VOLT, 0.601" O.D., BELDEN CAT. #1485A.
1F
8PR18AS
EIGHT PAIRS, ARMORED CABLE, #18 AWG, STRANDED
TINNED COPPER, OVERALL SHIELD AND DRAIN WIRE, 300V, TYPE
P-OS,0.99" O.D., OKONITE CAT.#564-10-3308.
1F
8PR18OS
EIGHT PAIRS, #18 AWG, OVERALL SHIELDED, TRAY CABLE,
600V, 0.603" O.D., BELDEN CAT.#1065A.
1F
8PR20IS
EIGHT PAIRS, #20 AWG, STRANDED, TRAY CABLE,
INDIVIDUALLY SHIELDED PAIRS, 300V, 0.54" O.D.,BELDEN
CAT. #1077A.
1F
8PR20OS
EIGHT PAIRS, #20 AWG, STRANDED, TRAY CABLE, OVERALL
SHIELD, 300V, 0.56" O.D., ANIXTER P/N 323-231-2008.
8PR22OS
EIGHT PAIRS, #22AWG, OVERALL SHIELDED.
8PR24TC
EIGHT PAIRS, #24AWG,TELE CBL, COPPER CONDUCTORS.
MFR: PREMIER.
8PR28F
EIGHT TWISTED PAIR, #28 AWG, TWIST'N'FLAT CABLE, LAMINATED
T'N'F, STYLE 2697, 300V, AMPHENOL SPECTRA-STRIP P/N
843-132-2801-016.
8PR28OS
EIGHT TWISTED PAIR, #28AWG, OVERALL SHIELDED. TINNED
COPPER, CHROME PVC JACKET. 0.330" O.D. BELDEN CAT#8138.
8PRPHONE
EIGHT PAIRS, #24 AWG, TELEPHONE CABLE, UNSHIELDED,
PVC, SOLID COPPER CONDUCTORS, TYPE MPR/CMR, LEVEL 4,
CATEGORY 3, MFR. PREMIER.
8/8/2011
TERM.TYPE
(See Table 3)
LFB
MS19S
DB15S
PUSHON
70
CABLE TYPE
CABLE DESCRIPTION
8THHN
ONE CONDUCTOR, #8 AWG, THHN, BLACK, 19 STRAND, 600V.
SLAC S/N 61-328-368-01.
9C12T6V
NINE CONDUCTOR, #12 AWG, TRAY CABLE, 600V,
UNSHIELDED, HOUSTON WIRE & CABLE CAT #H01428
0.615" O.D.
9C18J
NINE CONDUCTORS, #18AWG, UNSHIELDED.
9C18OS
See color
CODE TABLE
TERM.TYPE
(See Table 3)
1B
LFY, MS8PA
MS8PW, MS8PY
MS8SA
NINE CONDUCTORS, #18 AWG, 600V, TRAY CABLE, 0.48"
O.D., ALPHA CAT. #45410/9.
1N
MS8S
9C18T6V
NINE CONDUCTORS, #18 STRANDED, UNSHIELDED,
0.54" O.D., 600 VOLT RATED. USED FOR MAGNET MOVERS,
TRAY CABLE, ALPHA CAT.#45429.
1N
AMP9S, GP-CON
LFR, LSB#6
VAT7S
9C20OTN
NINE CONDUCTORS, #20 AWG, SHIELDED, LOW SMOKE ZERO HALOGEN,
300V, TRAY CABLE, 0.327” O.D.
MFG: LAKE CABLE, P/N: TXH209S.
9C24OS
NINE CONDUCTORS, #24 AWG, STRANDED TINNED COPPER, CM
RATED, 0.244" O.D., BELDEN CAT. 49906(A).
9PR18OS
NINE PAIR, #18AWG, OVERALL SHIELDED. MFR: OKONITE.
9PR20OS
NINE PAIR, #20AWG, OVERALL SHIELDED. MFR: OKONITE.
9PR22OS
NINE PAIR, #22 AWG, OVERALL SHIELDED, 300V, TRAY
CABLE, 0.488" O.D.,BELDEN CAT. #9520.
1F
9PR24IS
NINE PAIR, #24 AWG, TINNED COPPER INDIVIDUALLY
SHIELDED, CM RATED, 300V, 0.488" O.D. BELDEN CAT.#9732.
1P
9PR24ISP
NINE PAIR, #24AWG, INDIVIDUALLY SHIELDED,
POLYPROPYLENE INSULATED, COLOR CHART NO.3, 0.368"
O.D., MFG. BELDEN. P/N #9992.
9PR24OS
NINE TWISTED PAIRS, #24 AWG STRANDED TINNED COPPER DRAIN
WIRE, BELDFOIL OVERALL ALUMINUM-POLYESTER SHIELD, TEFLON
INSULATED, 0.246" O.D., BELDEN CAT.#82509.
10C16T3V
TEN CONDUCTOR, #16 AWG, 300V, STRANDED, UNSHIELDED,
TRAY CABLE, 0.43" O.D., ALPHA P/N 45080.
8/8/2011
1L
LSB#6, MS10P
71
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
10C18T3V
TEN CONDUCTOR, #18 AWG STRANDED, 300V, O.37"
O.D., UNSHIELDED, TRAY CABLE, ALPHA CAT. #45070.
1L
SPADE LUGS
10C18OS
TEN CONDUCTORS, #18 AWG, 300V, OVERALL SHIELDED,
STRANDED, TRAY CABLE ,0.38" O.D., ALPHA CAT. #45390.
1L
MS10P, MS10S
10C20OTN
TEN CONDUCTORS (5 PAIR), #20 AWG, LOW SMOKE ZERO HALOGEN,
300V, - UNCOATED COPPER PER ASTM B174.
• CROSS-LINKED POLYETHYLENE (XLPE) INSULATION
• COLOR CODE: METHOD 3 JACKET
• LOW-SMOKE, ZERO-HALOGEN CROSS-LINKED
POLYOLEFIN (LSZH XL POLYO) WHITE (WHT) JACKETED CABLES
ARE MULTI-CONDUCTOR, SHIELDED CONSTRUCTIONS,
SUITABLE FOR NON-WATERTIGHT, FLEXING SERVICE.
• MILITARY P/N M24643/12-02UN, TYPE LSSTOP-5, O.D. = 0.590
10C22J
TEN CONDUCTORS, #22 AWG,300V, .294" O.D.,
ALPHA WIRE P/N 1180C
10C22OS
TEN CONDUCTORS, #22 AWG, 300V, STRANDED, TRAY
CABLE, OVERALL SHIELDED, ALPHA CAT.#45199/10, 0.32" O.D.
1N
MS10P
10MTW-B
ONE CONDUCTOR, #10AWG, STRANDED, WIRE TYPE MTW, BLACK,
TFF, AWM, TEW, 600V, 500 FEET SPOOL.
10PRTHRM
TEN PAIR, #20 AWG, OVERALL SHIELD, SOLID WIRE, TYPE
PLTC THERMOCOUPLE EXTENSION CABLE, ASA/ISA TYPE TX,
OKONITE CAT-# 284-20-4120, 0.56" O.D. COLOR CODE: BLUE
(COPPER +) AND RED (CONSTANTAN -).
10PR16AS
TEN PAIRS, 300V, #16AWG, OVERALL SHIELD, TYPE
PLTC ARMORED INSTRUMENTATION CABLE. 1.21" O.D.
OKONITE P/N 561-10-3410.
10PR20GS
10 TWISTED PAIR, 20 AWG, SHIELDED, WITH NON-HALOGENATED
SHEATH. LAKE CABLE P/N 071019WGP3.
10PR20TN
TEN PAIR, 20 AWG, SHIELDED, LOW SMOKE ZERO HALOGEN, 300V,
TRAY CABLE, O.D., 0.539 IN., LAKE CABLE P/N: TXH2010PRS.
10PR22OS
TEN PAIRS, #22AWG, OVERALL SHIELD.
10THHN
ONE CONDUCTOR, #10 AWG, STRANDING 19,THHN,600V.
SLAC S/N 61-328-367-01.
8/8/2011
W1
POS19PS
72
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
11PR22OS
ELEVEN PAIRS, 300V, #22 AWG, STRANDED, TRAY CABLE,
OVERALL SHIELD, 0.536" O.D., BELDEN CAT. #9521.
1F
12C10TYR
TWELVE CONDUCTOR, TYREX TYPE SO, 600V, #10 AWG,
STRANDED, COPPER WIRE, 1.00" O.D. NOT FOR CABLE TRAY USE.
1A
12C12T6V
TWELVE CONDUCTOR, #12 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.685" O.D., HOUSTON WIRE & CABLE CAT.
#D0401212.
1B
12C12TYR
TWELVE CONDUCTOR, TYREX TYPE SO, 600V, #12 AWG,
STRANDED, COPPER WIRE, 0.80" O.D. NOT FOR CABLE TRAY
USE.
1A
12C16T6V
TWELVE CONDUCTOR, #16 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.65" O.D. ALPHA CAT. #45439/12.
1N
LFB, MS11P
MS16P
12C18J
TWELVE CONDUCTORS, #18AWG, 300V, BELDEN.
12C18OS
TWELVE CONDUCTORS, #18AWG, OVERALL SHIELD.
12C18T3V
TWELVE CONDUCTORS, #18 AWG, STRANDED, TINNED COPPER.
PVC INSULATED JACKET. 0.424" O.D., BELDEN CAT#8466.
12C18TC
TWELVE CONDUCTORS, #18AWG, 300V, TRAY CABLE,
UNSHIELDED, 0.38" O.D. PVC JACKET. ALPHA CAT#1898/12.
12C18TLN
TWELVE CONDUCTORS, #18AWG, OVERALL SHIELD, 7 STR
BX .030" XLPE OAS W/22GA 7 STR TC DRAIN IN .060"
O-HALOGEN BLK JACKET LS (UL) TC 600V 90C,
LAKE CABLE # VHX1820S(LS).
12C20J
TWELVE CONDUCTOR, #20AWG, TINNED COPPER, PVC
INSULATED. 0.338" O.D. BELDEN CAT#9457.
12C22T3V
TWELVE CONDUCTOR, #22 AWG, 0.6" O.D.
MFR: MANHATTAN.
12C22T6V
TWELVE CONDUCTOR, #22 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.52 O.D.", ALPHA CAT. #45409/12.
1N
LFR, MS26S
LRR1/4
12PR16AS
TWELVE PAIRS, ARMORED CABLE, 300V, #16 AWG,
STRANDED, TINNED-COPPER WIRE, OVERALL SHIELD AND DRAIN
WIRE, 1.13" O.D.,OKONITE CLX TYPE CAT-# P-OS 564-10-3412.
1F
8/8/2011
LFR, TT19S
MS19S
CA24S
73
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
12PR16OS
TWELVE PAIRS, #16 AWG, 300V, TRAY CABLE, 0.745"
O.D., OVERALL SHIELDED, BELDEN CAT. #1486A.
12PR16TC
TWELVE PAIRS, #16 AWG, TRAY CABLE,
OVERALL SHIELDED.
12PR18AS
TWELVE PAIR TWISTED SHIELDED 18AWG 7 STRAND, COPPER, OKOSEAL,
PVC JACKET, 600V APPROX. OD 1.040 P/N 561-10-3312 SEQ.PRINT
12PR18IS
TWELVE PAIR, #18AWG, INDIVIDUALLY SHIELDED, TINNED
COPPER, POLYETHYLENE INSULATED, DRAIN WIRE, PVC
JACKET, 0.735"O.D., BELDEN P/N #9776.
12PR18OS
TWELVE PAIRS, #18 AWG, OVERALL SHIELDED, 300V,
0.677" O.D., TRAY CABLE, BELDEN CAT. #1468A
12PR18TN
TWELVE PAIRS, INDIVIDUALLY SHIELDED, 18AWG, OVERALL SHIELD,
300V, LSZH JACKET TYPE XLPE, B/W NUMBERED PAIRS, TRAY RATED,
.649in DIAMETER, LAKE CABLE LLC, PN TXH1812PRS.
12PR20IS
TWELVE PAIRS, #20 AWG, INDIVIDUALLY SHIELDED.
12PR20OS
TWELVE PAIRS, #20 AWG, OVERALL SHIELDED, 300V,
STRANDED TRAY CABLE, BELDEN CAT. #1058A.
1F
12PR22IS
TWELVE PAIR, #22 AWG, 300V, INDIVIDUALLY SHIELDED,
0.464" O.D., CM RATED, BELDEN CAT. #9768.
1P
LFR, LRR1/4
12PR22OS
TWELVE TWISTED PAIRS, PLUS 1 SINGLE WIRE, #22 AWG,
STRANDED COPPER WIRE, WITH AN OVERALL SHIELD, WITH DRAIN
WIRE. CM RATED, SEE CONNECTOR TYPE FOR WIRING
INSTRUCTIONS. 0.455" O.D., BELDEN CAT. #8312.
1P
MS26PA, MS26SA
MS32P, LFR
MS19P, DAY-20
12PR22TN
12PR/ +1C 22GA STR TC CMG, SEMI RIGID PVC O/A AM SHIELD
65% TC BRAID SHIELD, LSZH BLK JACKET "LS" (UL) 2464,
0.487" O.D. LAKE CABLE 03602WGP4
12PR22SS
TWELVE PAIRS, #22 AWG, 300V SOLID COPPER WIRE,
OVERALL SHIELDED, 0.49" O.D., ALPHA CAT #3712
1K
MS24S, MS24P
SOLDER
12.5PR24
TWELVE AND HALF TWISTED PAIRS, #24 AWG STRANDED TINNED
COPPER DRAIN WIRE, BELDFOIL OVERALL ALUMINUM-POLYESTER
SHIELD, TEFLON INSULATED, 0.278" O.D., BELDEN CAT.#82512.
8/8/2011
1F
1F
74
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
12PRTHRM
TWELVE PAIR, #20 AWG, PVC JACKET, COPPERCONSTANTAN, OVERALL SHIELD 0.592" O.D., ANSI TYPE TX.
OMEGA CAT. #12TX20PP. COLOR CODE: BLUE (COPPER+) AND RED
(CONSTANTAN-).
12SMMTLN
12-STRAND, 50/125UM, (550 METER 10-GBE), MULTI-MODE,
OPTICAL BREAKOUT CABLE. LOW-SMOKE, ZERO-HALOGEN CABLE
SUITABLE FOR TRAYS AND RISERS. AQUA OUTER JACKET. OUTER
DIAMETER: 14MM(.55"). SUB-CABLE DIAMETER: 2.5MM(.10").
MINIMUM INSTALLATION BEND RADIUS: 21.1CM(8.3"). MINIMUM
LONG-TERM BEND RADIUS: 14.0CM(5.5").
OPTICAL CABLE CORPORATION PART NUMBER: BX012ZALE9QZ
13C22HV
THIRTEEN(BEL8869) CABLES, 22AWG, TINNED COPPER BRAID
SHIELD, BLACK PVC JACKET, PLENUM RATED, 0.645" O.D.
STORM PART#SP4433-B.
13PR28F
THIRTEEN PAIR #28AWG, FLAT/TWISTED CABLE, TINNEDCOPPER WIRE, BRAID SHIELD, PVC JACKET, 300V, 5AMP. 380" O.D.
STANDARD TWIST LENGTH IS 18" FOLLOWED BY A 2" FLAT
SECTION. BELDEN #9M28326.
15C20OS
FIFTEEN CONDUCTOR, #20 AWG, OVERALL SHIELD, 300V,
STRANDED, TRAY CABLE, 0.39" O.D., ALPHA CAT. #45470/15.
1L
DB15P
15C24OS
FIFTEEN CONDUCTOR, #24 AWG, OVERALL SHIELD, 300V,
STRANDED, TRAY CABLE, 0.33" O.D., ALPHA CAT. #45100/15.
1N
DB15P
15C24OTN
FIFTEEN CONDUCTORS, #24 AWG, OVERALL SHIELDED, TIN COPPER
BRAIDED, WITH DRAIN WIRE, LOW SMOKE ZERO HALOGEN, 300V,
O.D. = 0.315" MFG: L-COM P/N: CSLSZH15-XXX
(XXX= LENGTH OF 100, 500, 1000FT)
15PR16IS
FIFTEEN PAIR, #16AWG, INDIVIDUALLY SHIELDED, 600V,
1.125" O.D., TRAY CABLE, SUN RESISTANT, THERMO
ELECTRIC CATALOG.
15PR22IS
FIFTEEN PAIR, #22AWG, INDIVIDUALLY SHIELDED, 30V, CM
RATED, 0.548" O.D., BELDEN CAT. #8776.
1P
15PR22OS
FIFTEEN PAIR, #22 AWG, 300V, OVERALL SHIELD, TRAY
CABLE, 594" O.D., BELDEN CAT #9524.
1F
8/8/2011
LFR, TT30S
MS32P, MS26S
MS26P, MS26PG
MS28P, MS28S
75
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
15PR22SS
FIFTEEN TWISTED PAIRS, #22 AWG, SOLID CONDUCTORS,
INDIVIDUALLY SHIELDED, CM RATED, 300V, 0.525" O.D.,
BELDEN CAT #8766.
15PR22TS
FIFTEEN PAIRS, #22 AWG, 300V, 7 TC STRANDS,
OVERALL SHIELD, TRAY CABLE. 0.594" O.D. BELDEN CAT#9524.
16C22OS
SIXTEEN CONDUCTORS, #22 AWG, OVERALL SHIELDED.
16PR16AS
SIXTEEN PAIR, #16 AWG, 300V, ARMORED SHIELD, 1.26"
O.D., TRAY CABLE, OKONITE CAT. #564-10-3416.
1F
16PR16IS
SIXTEEN PAIR, #16 AWG, 600V, TRAY CABLE, INDIVIDUALLY
SHIELDED 1.023" O.D., BELDEN CAT. #1043A.
1F
16PR16OS
SIXTEEN PAIR, #16 AWG, 600V, OVERALL SHIELDED, TRAY
CABLE, BELDEN CAT. #1073A.
1F
16PR20AS
SIXTEEN PAIRS, #20 AWG, ARMORED CABLE, 300V,
STRANDED, TRAY CABLE, 1.03" O.D., OKONITE CAT. #564-10-3216.
1F
16PR20KT
16-PAIR, K-TYPE THERMOCOUPLE EXTENSION CABLE.
20AWG, SOLID CONDUCTORS.POSITIVE WIRE: YELLOW.
NEGATIVE WIRE: RED. ALUMINUM/MYLAR OVERALL
SHIELD WITH DRAIN WIRE. OMEGA PART NUMBER 16KX20PP.
17PR28RF
SEVENTEEN PAIR, #28AWG, PVC SHIELDED, ROUND-TO-FLAT,
300V RMS,0.050" PITCH MASS-TER CABLE. BELDEN CAT.#9M-28334.
18MTW
ONE CONDUCTOR, #18AWG, STRANDED, WIRE TYPE MTW,
TFF, AWM, TEW, 600V, 6AMPS, 500 FEET SPOOL, GRAINGER.
18PR22OS
EIGHTEEN TWISTED PAIRS, 300V, #22 AWG, STRANDED,
COPPER WIRE, OVERALL SHIELD WITH DRAIN WIRE, 0.54" O.D.,
SLAC SPECIAL SLAC S/N61-329-326-19.MFG. GORE, OR EQUAL.
8/8/2011
1J
TERM.TYPE
(See Table 3)
LFB
AMP36P,LFR,D37S,
D37P,LFB,DB52S,
AMP48P,MS19S,TT30P,
DD50S,UVC90
76
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
18PR22TN
EIGHTEEN TWISTED PAIRS, # 22 AWG, STRANDED, COPPER WIRE
OVERALL SHIELD WITH DRAIN WIRE, LSZH JACKET, 0.50" O.D.
SPECIAL ORDER, MFG: BELDEN, P/N: Y52530.
NOTE: Any termination of this cable with an AMP36P
Connector is to be done as indicated on drawing CA-123-693-00.
The drawing exceptions are:
1) Use the length as appropriate for the indicated
cable, and
2) Label the cable with the SLAC-Standard computer
Generated labels.
18PR24IS
EIGHTEEN PAIRS, #24 AWG, INDIVIDUALLY SHIELDED.
18PR28OS
EIGHTEEN TWISTED PAIRS, #28 AWG, STRANDED, CL2 RATED,
OVERALL SHIELD WITH DRAIN WIRE. 0.365" O.D.,BELDEN CAT #9819
NINETEEN CONDUCTOR, #12 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.800" O.D., HOUSTON WIRE&CABLE CAT.#D0401219.
19C12T6V
TERM.TYPE
(See Table 3)
1P
1B
LRY
19C16/3V
NINETEEN CONDUCTOR, #16 AWG.
19C16T3V
NINETEEN CONDUCTOR, #16AWG, 300V, STRANDED.
19C16T6V
NINETEEN CONDUCTOR, #16 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.74" O.D., ALPHA CAT. #45439/19.
1N
MS16P,LFB
19C18OS
NINETEEN CONDUCTOR, #18 AWG, 600V, TRAY CABLE,
OVERALL SHIELD, 0.64" O.D., ALPHA CAT. #45430/19.
1N
LFR, MS20P
19C18T6V
NINETEEN CONDUCTOR, #18 AWG, 600V, TRAY CABLE,
UNSHIELDED, 0.68" O.D., ALPHA CAT. #45429/19
1N
TT19SM TT19P
LFR
19C22TEF
NINETEEN CONDUCTORS, #22AWG, TINNED COPPER CONDUCTORS, FEP
TEFLON INSULATION, TEFLON JACKET, RED TINT, 0.269" O.D.
BELDEN CAT#83569.
19PR18OS
NINETEEN PAIR, #18 AWG, 300V, OVERALL SHIELD, 0.75"
O.D. ALPHA CAT. #45379/19.
1H
19PR22IS
NINETEEN PAIR, #22 AWG, 300V, INDIVIDUALLY SHIELDED,
TRAY CABLE, 0.686" O.D., BELDEN CAT. #9335.
1F
19PR22OS
NINETEEN PAIR, #22 AWG.
8/8/2011
MS41P, MS41S
LFR, VIK-44,PUSHON
77
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
19PR24OS
NINETEEN PAIR, #24 AWG, 300V, OVERALL SHIELDED, CM RATED,
0.448" O.D., BELDEN CAT#9519.
1P
MS32P, MS32S
20C20OS
TWENTY CONDUCTORS, #20 AWG, 300V, OVERALL
SHIELDED, TRAY CABLE,0.43" O.D., ALPHA CAT. #45470/20.
1L
LFR, MS32S
MS10P
24PR16AS
TWENTY-FOUR PAIR, #16 AWG, 300V, ARMORED SHIELD, TRAY
CABLE, 1.53" O.D., OKONITE CAT#564-10-3424.
1F
24PR16OS
TWENTY-FOUR PAIR, #16 AWG, OVERALL SHIELD, 600V, TRAY
CABLE, 1.147" O.D., BELDEN CAT. #1074A.
1F
24PR16TC
TWENTY-FOUR PAIR, #16 AWG, TRAY CABLE.MFR: OKONITE.
24PR18AS
24 PAIR TWISTED SHIELDED 18AWG 7 STRAND, COPPER, OKOSEAL,
PVC JACKET, 600V APPROX. OD 1.350 P/N 561-10-3324 SEQ.PRINT
24PR18IS
TWENTY-FOUR PAIR, #18 AWG, 300V, INDIVIDUALLY SHIELDED,
TRAY CABLE,1.025" O.D., BELDEN CAT. #1480A.
1F
24PR18OS
TWENTY-FOUR PAIRS, #18 AWG, OVERALL SHIELDED, TRAY CABLE,
600V, BELDEN CAT.#1068A. 1.027" O.D.(300V FROM ANIXTER)
1F
24PR18TC
TWENTY-FOUR PAIRS, #18 AWG, TRAY CABLE, OVERALL SHIELDED.
24PR20TC
TWENTY-FOUR PAIRS, #20 AWG, TRAY CABLE.
24PR22IS
TWENTY FOUR PAIR, #22 AWG, INDIVIDUALLY SHIELDED, CM
RATED, 0.891" O.D., BELDEN CAT. #1821A.
24PR20SS
TWENTY-FOUR PAIR, #20 AWG, OVERALL SHIELDED, SOLID WIRE,
0.875" O.D.
24PRTHRM
TWENTY-FOUR PAIR, #20 AWG, PVC JACKET, COPPER
CONSTANTAN, OVERALL SHIELD, 0.770" O.D., ANSI TYPE TX.
OMEGA CAT. #24TC20PP. COLOR CODE: BLUE (COPPER +)
AND RED(CONSTANTAN -).
25C16T3V
TWENTY-FIVE CONDUCTORS, #16 AWG, 300V, STRANDED, TRAY
CABLE 0.66" O.D., ALPHA CAT. #45080/25.
25C16T6V
TWENTY-FIVE CONDUCTORS, #16 AWG, 600V, UNSHIELDED
TRAY CABLE. 0.93" O.D. ALPHA CAT#1085.
8/8/2011
1F
1L
78
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
25C20OS
TWENTY-FIVE CONDUCTORS, #20 AWG, OVERALL SHIELD,
300V, TRAY CABLE, O.47" O.D., ALPHA CAT.#45470/25.
25C20TN
TWENTY-FIVE CONDUCTORS, #20 AWG, SHIELDED, LOW SMOKE ZERO HALOGEN,
300V, TRAY CABLE, O.D. 0.502 IN.
MFG: LAKE CABLE, P/N: TXH2026S.
25C24OS
TWENTY-FIVE CONDUCTORS, #24 AWG.
25C26OS
TWENTY-FIVE CONDUCTORS, #26 AWG.
25C28F
TWENTY-FIVE CONDUCTOR, #28 AWG, FLAT RIBBON CABLE,
STRANDED TINNED COPPER WIRE, WITH GRAY PVC INSULATION,
RED POLARITY STRIPE. 0.050 PITCH NOMINAL WIDTH 1.25",
300V RATING, BELDEN CAT. #9L28025. NOT CABLE TRAY RATED.
25PR19SS
TWENTY-FIVE PAIR, #19 AWG, SOLID CONDUCTORS, OVERALL
SHIELD, 1.0" O.D.
25PR22OS
TWENTY-FIVE PAIR, #22 AWG, OVERALL SHIELDED, 300V
STRANDED TINNED COPPER, 0.620: O.D., CM RATED, BELDEN CAT.
#8325.
1P
25PR24IS
TWENTY-FIVE PAIRS, DATA TRANSMISSION CABLE, #24 AWG,
INDIVIDUALLY SHIELDED, CM RATED, 0.94" O.D., BELDEN
CAT. #8185.
1P
25PR24OS
TWENTY-FIVE PAIRS, #24 AWG, 300V, STRANDED, CM RATED,
OVERALL SHIELDED, 0.708" O.D., BELDEN CAT. #9550.
1P
25PR24SR
TWENTY-FIVE PAIRS, #24 AWG, TINNED COPPER, S-R PVC
INSULATED, TWISTED PAIRS, OVERALL BELDFOIL ALUM-POLY SHIELD,
CHROME PVC JACKET, 300V, 0.503" O.D., BELDEN CAT.#9525.
25PR24SS
TWENTY-FIVE PAIRS, #24 AWG, OVERALL SHIELDED, SOLID
CONDUCTORS, REA PE-22, TELEPHONE CABLE O.55" O.D.,
ANIXTER E-002524AAC
25PR28OS
TWENTY-FIVE TWISTED PAIRS, #28 AWG, STRANDED, CL2 RATED,
OVERALL SHIELD WITH DRAIN WIRE.0.429" O.D.,BELDEN CAT#9825
8/8/2011
1L
TERM.TYPE
(See Table 3)
DB15P
LFR
PUSHON
79
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
25PRCAT5
TWENTY-FIVE PAIRS, #24 AWG, TIA/EIA 568-A CAT 5,
OVERALL SHIELDED, SCREENED TWISTED PAIR (ScTP).
THERMOPLASTIC, GRAY PVC .522" O.D.
NON-PLENUM, MOHAWK PART NO.# M56832
25PCAT5E
TWENTY-FIVE PAIRS, #24 AWG, TIA/EIA 568-A CAT 5E,
OVERALL SHIELDED. THERMOPLASTIC, GRAY PVC .470" O.D.
NON-PLENUM, MOHAWK PART NO.# M58141
26C16/3V
SAME AS 3C16/3V EXCEPT: TWENTY-SIX CONDUCTORS, 0.7"O.D.
1A
LFB, MS11S, MS21P,
MS26P, MS26S, TT19P,
MS21S, LFR
26C22/3V
SAME AS 3C16/3V EXCEPT: TWENTY-SIX CONDUCTORS, #22 AWG,
0.7" O.D.
1A
LFR, MS19S
26C22OS
TWENTY-SIX CONDUCTORS, #22 AWG, OVERALL SHIELDED.
26C24OS
TWENTY-SIX CONDUCTOR, #24 AWG, STRANDED TINNED
COPPER WIRE, 0.38" O.D. SLAC S/N61-329-326-26.
1N
DB25S, DB25P
26PR22OS
TWENTY-SIX TWISTED PAIRS, 300V, #22 AWG, STRANDED, COPPER
WIRE, OVERALL SHIELD WITH DRAIN WIRE, LBL SPEC. LBL-95-10E.
0.5" O.D.
1A
27C20OS
TWENTY-SEVEN CONDUCTORS, #20 AWG, STRANDED
COPPER, OVERALL SHIELD,CM RATED, 300V, 0.52" O.D.,ALPHA
NO.5565C.
1N
27C22TC
TWENTY-SEVEN CONDUCTOR, #22 AWG, STRANDED, 300V,
UNSHIELDED, CM RATED, 0.45" O.D., ALPHA CAT. #5215C.
1N
27PR22OS
TWENTY-SEVEN PAIR, #22 AWG, 300V, OVERALL SHIELD, 0.741"
O.D., TRAY CABLE, BELDEN CAT. #9527.
1F
27PR24IS
TWENTY-SEVEN PAIRS, #24 AWG, 300V, INDIVIDUALLY SHIELDED
CM RATED, 0.797" O.D., BELDEN CAT. #9738.
1P
28P22OSS
SLAC MADE, 28 TWISTED PAIRS OF 22 AWG,TINNED STRANDED COPPER.
WIRES ARE TFE INSULATED (RED/WHITE). WIRES ARE THEN WRAPPED
IN STRANDED,TINNED COPPER EXPANDABLE WIRE TUBES
(.38 DIAMETER TYP.- MIL-SPEC INC P/N 2146)AND THEN WRAPPED
IN STRANDED EXPANDABLE POLYETHYLENE TUBES
(ALTA TECH, 1" DIA PE FLEXIBLE TUBE).
8/8/2011
LFR, SOLDER
80
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
30PR26OS
THIRTY PAIR, #26 AWG, STRANDED OVERALL SHIELDED, 0.5"
O.D. SLAC S/N61-329-326-30, GORE CAT.#RCN2294-REV-A.
32C18OS
32 CONDUCTORS 18AWG OVERALL SHIELD LOW SMOKE ZERO HALOGEN
CABLE TRAY RATED, RAYCHEM # EPD-RWC-20078-L022.
32C18TLN
THIRTY-TWO CONDUCTOR, #18AWG STRANDED TINNED COPPER,
300V TRAY CABLE,ZERO HALOGEN.0.611”O.D.,WT=0.288LBS/
FT.RAYCHEM WCD51/1611.
34PRSCSI
68 PIN CONN OVER SHIELDED PLUG WITH ASSEMBLED STANDARD
TERMINATION COVERS. AMPLIMITE SERIES III THERMOPLASTIC.
AMP PART # 68KEK00051.
36PR16AS
C-L-X® TYPE SP-OS TYPE ITC/PLTC ARMORED INSTRUMENTATION
CABLE MULTIPLE SHIELDED PAIRS OR TRIADS-METAL JACKET
OVERALL SHIELD 600 VOLTS - 105°C RATING FOR CABLE TRAY USE
OKONITE P/N 561-60-3436 O.D. 1.53".
36PR16OS
THIRTY-SIX PAIR, #16 AWG, 300V, OVERALL SHIELDED, TRAY
CABLE, 1.184" O.D., BELDEN CAT. #1494A.
36PR18TN
THIRTY-SIX PAIR TWISTED SHIELDED, 7 STR BC LSXLPE
O/A SHIELD 300V PLTC LAKE CABLE P/N TXH1836RPS O.D. 1.023in.
UL listed as Type PLTC per UL standard 13 IEEE 383, UL 2250,
& 1581(1685)
36PR18OS
THIRTY-SIX PAIR, #18 AWG, 300V, STRANDED, OVERALL SHIELD,
TRAY CABLE, 1.062" O.D., BELDEN CAT. #1472A.
37C24OS
THIRTY-SEVEN CONDUCTORS, #24 AWG LLL CABLE.
37C24TEF
EIGHTEEN AND ONE-HALF PAIRS, #24AWG TINNED COPPER,
FOAM INSULATED, TWISTED PAIRS. OVERALL BELDFOIL
ALUMINUM-POLYESTER SHIELD 24 AWG STRANDED TINNED
COPPER DRAIN WIRE. GRAY FLUOROCOPOPOLYMER JACKET,
300V, NEC ARTICLE 800, 0.484"O.D. BELDEN P/N 88118.
37C28FLT
THIRTY-SEVEN CONDUCTOR, #28AWG, FLAT RIBBON CABLE
STRANDED TINNED COPPER, NORMAL WIDTH 1.85", 300V,
0.50" PITCH, BELDEN CAT.#9R28037.
8/8/2011
TERM.TYPE
(See Table 3)
AMP48P
SCSI68P
1F
1F
LFR
1a
81
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
40C18T3V
FORTY CONDUCTORS, #18 AWG, 300V, STRANDED, TINNED COPPER
WIRE, UNSHIELDED, TRAY CABLE, 0.69" O.D., ALPHA CAT.
#45070/40.
1L
LFR
40C24OS
FORTY CONDUCTOR, #24 AWG, 300V, OVERALL SHIELD, CM
RATED 0.430" O.D., BELDEN CAT. #9545.
1A
3M40S
40C28FOS
FORTY CONDUCTOR, #28 AWG, FLAT RIBBON CABLE, SHIELDED
AND JACKETED,TWISTED PAIR, PVC/PVC, TINNED STRANDED
COPPER, 3M P/N 1785/40.
40PR18AS
50PR16AS DESCRIPTION: C-L-X® TYPE SP-OS TYPE ITC/
PLTC ARMORED INSTRUMENTATION CABLE MULTIPLE SHIELDED PAIRS
OR TRIADS-PVC JACKET OVERALL SHIELD 300 VOLTS-105ºC RATING
FOR CABLE TRAY USE OKONITE P/N 561-10-3450.
50C28FOS
FIFTY CONDUCTOR, #28 AWG, FLAT RIBBON CABLE, SHIELDED
AND JACKETED,TWISTED PAIR, PVC/PVC, TINNED STRANDED
COPPER.
50C16T3V
FIFTY CONDUCTOR, #16 AWG, 300V, 0.93" O.D., UNSHIELDED,
TRAY CABLE, ALPHA CAT. #45080/50.
1L
LFB
50C16OS
FIFTY CONDUCTOR, #16 AWG, 300V, OVERALL SHIELD,
TRAY CABLE 0.93" O.D. ALPHA CAT. #45370/50.
1L
LFB
50C18OS
FIFTY CONDUCTOR, #18 AWG, 300V, TRAY CABLE,
OVERALL SHIELD, 0.76" O.D., ALPHA CAT. #45390/50.
1L
LFB, BULLET
50C18TLN
50C/18GA 7STR BC XLPE, OAS W/ 20GA 7STR TC DRAIN IN
0-HAL BLK JACKET "LS" (UL) TC 600V 90C, 80MILS,
1.573”O.D. AMERCABLE GEXOL-HF.
50C20OS
FIFTY CONDUCTOR, #20 AWG, OVERALL SHIELD, 300V,
0.67" O.D., ALPHA CAT. #45470/50.
1L
LFR
50C24IS
FIFTY CONDUCTOR, #24 AWG, INDIVIDUALLY SHIELDED TELCO.
50PR16AS
SAME AS 4PR16AS EXCEPT: FIFTY PAIRS, 1.98" O.D.,
OKONITE CLX TYPE P-OS 564-10-3450
1F
50PR16OS
FIFTY PAIRS, #16 AWG, 600V, OVERALL SHIELDED, TRAY CABLE,
1.598" O.D., BELDEN CAT. #1090A.
1F
8/8/2011
D37P
82
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
50PR16TC
FIFTY PAIRS, #16 AWG, TRAY CABLE. MFR: OKONITE.
50PR18AS
FIFTY PAIRS, #18 AWG, ARMORED CABLE, 300V, OVERALL
SHIELDED,WITH DRAIN WIRE, 1.72" O.D., OKONITE CLX TYPE
P-OS P/N 564-10-3350.
1F
50PR18OS
FIFTY PAIR, #18 AWG, 600V, OVERALL SHIELDED, TRAY CABLE,
1.456" O.D., BELDEN CAT.#1088A.
1F
50PR22S
FIFTY PAIRS, #22 AWG, SOLID COPPER WIRE, UNSHIELDED,
0.50"O.D. PLENUM CABLE.
50PR24NS
FIFTY PAIRS,#24 AWG, NO SHIELD. PVC JACKET.
TELEPHONE WIRE.
50PR24OS
FIFTY PAIR, #24 AWG, OVERALL SHIELDED.
50PR24SS
FIFTY PAIRS, #24 AWG, SOLID COPPER WIRE, OVERALL SHIELD,
SOLID CONDUCTORS, REA PE22, 0.70" O.D., ANIXTER E-005024AAA.
51PR22OS
FIFTY-ONE TWISTED PAIRS, #22 AWG, ANNEALED COPPER WIRE
OVERALL SHIELD WITH DRAIN WIRE, 300V, 1.00" O.D.,
MFG. SLAC SPECIFICATION #PS 114-001-01-R3.
1X
51PR22SS
FIFTY-ONE TWISTED PAIRS, #22 AWG, SOLID CONDUCTOR,
OVERALL SHIELD WITH DRAIN WIRE, 300V, 0.710" O.D., CM
RATED, BELDEN CAT #8751.
1P
52C16/3V
FIFTY-TWO CONDUCTOR, #16 AWG, 300V, UNSHIELDED, 1.00"
O.D., MFR UNKNOWN.
1A
55C22OS
FIFTY-FIVE CONDUCTOR, #22 AWG, 600V, OVERALL
SHIELDED 0.75" O.D. MFR UNKNOWN.
60C16OS
SIXTY CONDUCTOR, #16 AWG, OVERALL SHIELDED, 300V,
TRAY CABLE, 1.00" O.D., ALPHA CAT. #45370/60.
100PR24S
ONE HUNDRED PAIRS, #24 AWG, OVERALL SHIELDED, SOLID
CONDUCTORS, REA PE-22, TELEPHONE CABLE, 0.87" O.D.,
ANIXTER E-010024AAC.
8/8/2011
TERM.TYPE
(See Table 3)
LFB
LFR, SOLDER
1L
PUSHON
83
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
262FLX
DIESEL LOCOMOTIVE CABLE,
MINIMUM WIRES PER CONDUCTOR 646, NOMINAL OUTSIDE DIAMETER IN 0.973,
APPROX. WEIGHT LBS. PER 1,000 FT. 1436, AMPACITY 90DEG. 591,
EXTRA FLEXIBLE CABLE, 600V,
STORES ID: 146102
PART # AMERCABLE 37-119-215,
PLEASE SEE GENERAL NOTES # 8
AC-BM1
AC LINE CORD FOR EXISTING BUSINESS MACHINES.
PREWIRED WITH MOLDED CONNECTORS. BELDEN P/N 17952, #16
AWG,3 CONDUCTOR, 13A, SLAC P/N61-329-704-01.
AC-BM2
AC LINE CORD FOR EXISTING BUSINESS MACHINES
PREWIRED WITH MOLDED CONNECTORS. ONE END HAS A PH290B
CONNECTOR AND THE OTHER END HAS A SPH386. BELDEN P/N
17255C, #16 AWG, 3 CONDUCTOR,13A, SLAC P/N61-329-704-02.
BWRB12
A SET OF 4 WIRES CONSISTING OF ONE EACH OF THE
FOLLOWING: #12-BLK, #12-RED, #12-BLU AND #12-WHT. THIS IS
TREATED AS A SINGLE CABLE.
CAMLNK10
CUSTOM COMMERCIAL CABLE, P/N # CLCP-10-P#3179,INTERCON 1
NORTECH SYSTEMS.
CAT6TLN
CATEGORY 6 LSZH UTP SOLID & STRANDED CABLES HORIZONTAL CABLE:
1*24AWG SOLID COPPER POLYOLEFIN INSULATION & FILLER,
JACKET: LSZH,UL-E151955/CSA-LL79189/ETL Cable Master.236" OD
CAT6STLN
CATEGORY 6, 26 AWG TINNED COPPER (STRANDED), OVERALL SHIELD,
LOW SMOKE, ZERO HALOGEN JACKET,JACKET COLOR LIGHT GRAY,
0.24" O.D. (NOMINAL).
CONVGAU1
SPECIAL PREWIRED CABLE ASSEMBLY FOR A CONVECTRON VAC
GAUGE. THERE IS AN AMP15P CONNECTOR ON ONE END AND A
GP5S ON THE OTHER END. THIS CABLE IS SUPPLIED BY THE
CONTROLS VACUUM GROUP.
CNT100FR
.110" COAX, 50 OHM IMPEDANCE, FOAM DIELECTRIC,LSZH JACKET,
MAX FREQ 61.00 GHZ, ANDREW CINTH CABLE P/N CNT100FR .
CNT195
COAXIAL CABLE, 50 OHMS, CAPACITANCE 24 PF/FT, 0.195” O.D.,
NON-HALOGEN, FLAME RETARDANT POLYOLEFIN,
(NOT: LOW SMOKE OR TRAY RATED),MFG: ANDREW, P/N: CNT-195-FR.
8/8/2011
TERM.TYPE
(See Table 3)
PH290B, SPH386
84
CABLE TYPE
CABLE DESCRIPTION
CNT195FR
.195" COAX, 50 OHM IMPEDANCE, FOAM DIELECTRIC,LSZH JACKET,
MAX FREQ 37.9 GHZ, (SEE LMR195FR FOR EQUIVALENT)
ANDREW CINTH CABLE P/N CNT195FR.
DB9MFV
PRE-FABRICATED COMPUTER CABLE D-SUB 9 PIN MALE TO FEMALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPPLIERS, IE. "FRY'S ELECTRONICS"
DB9MMV
PRE-FABRICATED COMPUTER CABLE D-SUB 9 PIN MALE TO MALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS, IE. "FRY'S ELECTRONICS"
DB25MFV
PRE-FABRICATED COMPUTER CABLE D-SUB 25 PIN MALE TO FEMALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPPLERS, IE. "FRY'S ELECTRONICS"
DB25MMV
PRE-FABRICATED COMPUTER CABLE D-SUB 25 PIN MALE TO MALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPPLERS, IE. "FRY'S ELECTRONICS
DC-BUS
THIS INDICATES A SPECIAL LARGE CONDUCTOR, OFTEN
WATER-COOLED, NORMALLY USED FOR THE CONNECTION OF
HIGH-CURRENT MAGNETS. THE ACTUAL CONDUCTOR WILL BE
SPECIFIED ON THE INSTALLATION DRAWING, OR IN THE
INSTALLATION INSTRUCTIONS, FOR THAT PARTICULAR SYSTEM.
DS2124
SINGLE CONDUCTOR, SHIELDED, #16 AWG, 100VDC, 0.440"
O.D., DIELECTRIC SCIENCES P/N 2124.
ELOCAB
TWO CONDUCTORS, #22AWG, (RED&BLACK),AND 2 TWO CONDUCTOR
#XXAWG STRANDED WITH BRAIDED SHIELD. ROUND CABLE, 150V,
OVERALL FOIL SHIELD WITH BRAID SHIELD, BENDING RADIUS 2
TIMES DIAMETER, X.XXX" O.D., ELOCAB P/N ERK 4181.
EXT-10
AC EXTENSION CORD, U-GROUND, 10' LONG, #16 AWG, 3
CONDUCTOR, MALE PLUG ON ONE END, FEMALE PLUG ON THE
OTHER END, SJO OR SJ CORD, MOLDED PLUGS, SLAC
P/N 61-329-702-05.
FIBOPT
FIBER OPTIC CABLE, MFR: ANIXTER.
8/8/2011
See color
CODE TABLE
TERM.TYPE
(See Table 3)
85
CABLE TYPE
CABLE DESCRIPTION
FIBOPT1
FIBER OPTIC CABLE ASSEMBLY,THIS CABLE IS FACTORY
TERMINATED WITH SMA-TYPE CONNECTORS. CABLE IS ORDERED
IN SPECIFIC LENGTHS, KINETIC SYSTEMS CAT #5802-D201,
O.242" O.D. THIS CABLE IS TO BE TERMINATED BY QUALIFIED
PERSONNEL ONLY.
FIBOPT2
MULTI-FIBER, 2 FIBERS, CORE/CLADDING DIAMETER IS
100/140, CABLE TYPE 2, CABLE O.D.= .11X.21. THIS IS A
CABLE ASSEMBLY ORDERED IN SPECIFIC LENGTHS WITH ST-TYPE
CONNECTORS, ANNIXTER CAT. #370-047-100-/140SP-2.
FIBOPT3
MILTI-FIBER, 2 FIBERS, CABLE TYPE 2, DFNP PLENIUM
RATED, MAX. Att. 3.75/1.5dB/km. MINIMUM BEND RADIUS 2.0
INCHES. MFR SIECOR P/N 002K58-31141-24. ANIXTER P/N
370-148-62SJ-2.
FIBOPT4
ONE CONDUCTOR, ZERO HALOGEN, 0.102" O.D.,
MFG EUROFO, P/N FT2G0037.
FIBOPT5
EIGHT FIBER, PLENUM (OFNP), MULTIMODE, MAXIMUM
ATTENUATION. 850 n m/3.75 to 1300 n m/1.2 DB/KM.
0.410" O.D. MFG 3M THRIFTY-BIT.
FIBOPT6
SINGLE FIBER, PLENUM RATE, MFR: 3M #FT-400-EMT.
FIBOPT06
SINGLE MODE 6 STRAND, RADIATION RESISTANT, LOOSE TUBE,
LSZH (FRPE), FUJIKURA P/N LL006ALC5101N1, SPEC. DNL-3224
CABLE DIAMETER .469 IN.
FIBOPT7
MULTI-FIBER,24 FIBERS IN 4 SUB UNITS, 900UM, TIGHT BUFFER
W/EPOXY GLASS ROD & ARAMID FIBER YARN, FLAME-RETARDANT
PVC, ORANGE JACKET, 20 X O.D. MIN. BEND RADIUS
(INSTALLATION),(UL) LISTED TYPE OFNR,.529". O.D., GENERAL
CATALOG # XX0241 AIR.
FIBOPT8
50/125 µM, 24MM, 12 SM HYBRID VERSION, PE INNER AND
OUTER JACKETS, 3.0 MM BUFFER TUBE, ULTRAVIOLET-RESISTANT,
FLAME RETARDANT, ZERO HALOGEN,IEEE-383 COMPLIANT,LISTED
OFN-LS AND CSA FT4-ST1, CABLE TRAY RATED.
CORNING CABLE SYSTEMS.
8/8/2011
See color
CODE TABLE
TERM.TYPE
(See Table 3)
OPTIC
SC&ST
ST,SC
86
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
FIBOPT9
50/125 µM, DUPLEX MM, PE INNER AND OUTER JACKETS, 3.0 MM
BUFFER TUBE, ULTRAVIOLET RESISTANT, FLAME RETARDANT, ZERO
HALOGEN, IEEE-383 COMPLIANT, LISTED OFN-LS AND CSA FT4-ST1,
CABLE TRAY RATED. CORNING CABLE SYSTEMS.
FIBOPT10
50/125 µM, 48MM, 24 SM HYBRID VERSION, PE INNER AND
OUTER JACKETS, 3.0 MM BUFFER TUBE, ULTRAVIOLET-RESISTANT,
FLAME RETARDANT, ZERO HALOGEN,IEEE-383 COMPLIANT, LISTED
OFN-LS AND CSA FT4-ST1, CABLE TRAY RETED.
CORNING CABLE SYSTEMS.
FIBOPT11
COMMERCIAL CABLE, VENDOR TYCO ELECTRONICS, LIGHTRAY MPO,
OPTIMATE, 12 – 50/125 MICRON FIBERS, OFNP, DRG. NO. C-1435028.
DIAMETER OF THE CABLE AT 0.25”
FIBOPT12
(FORMALLY 6 STRAND RAD HARD FUJIKURA),SINGLE MODE,12 STRAND,
RADIATION RESISTANT, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL006ALC510N1, SPEC. DNL-3224 CABLE DIAMETER .469 IN.
FIBOPT13
SINGLE MODE, 48 STRAND, RADIATION RESISTANT, LOOSE TUBE,
LSZH (FRPE),FUJIKURA P/N LL0048ALC510N1, SPEC. DNL-3225
CABLE DIAMETER .??? IN.
FIBOPT14
SINGLE MODE, 72 STRAND, RADIATION RESISTANT, LOOSE TUBE,
LSZH (FRPE),FUJIKURA P/N LL0072ALC610N1 SPEC. DNL-3226
CABLE DIAMETER .??? IN.
FIBOPT24
SINGLE MODE 24 STRAND, RADIATION RESISTANT, LOOSE TUBE,
LSZH (FRPE), FUJIKURA P/N LL024ALC5101N1, SPEC. DNL-3224
CABLE DIAMETER .469 IN.
FIBOPT48
(FORMALLY 13 STRAND RAD HARD FUJIKURA) SINGLE MODE
48 STRAND,RADIATION RESISTANT, LOOSE TUBE, LSZH (FRPE),
FUJIKURA P/N LL048ALC5101N1, SPEC. DNL-3225 CABLE
DIAMETER .469 IN.
FIBOPT72
(FORMALLY 14 STRAND RAD HARD FUJIKURA) SINGLE MODE
72 STRAND,RADIATION RESISTANT,LOOSE TUBE, LSZH (FRPE),
FUJIKURA P/N LL072ALC6101N1, SPEC. DNL-3226 CABLE
DIAMETER .500 IN.
FIBOPT96
SINGLE MODE 96 STRAND, RADIATION RESISTANT, LOOSE TUBE,
LSZH (FRPE), FUJIKURA P/N LL096ALC8101N1, SPEC. DNL-3226
CABLE DIAMETER .571 IN.
8/8/2011
TERM.TYPE
(See Table 3)
87
See color
CODE TABLE
CABLE TYPE
CABLE DESCRIPTION
FIBOSM02
SINGLE MODE 02 STRAND, LOOSE TUBE, LSZH (FRPE), AFL
Telecommunications P/N KE0029481801 SM, .469 IN Max.
tensile load short term 600lbs, long term 200lbs,
77lbs per 1000ft nominal weight. Minimum bend radius
Short term 9.4in., Long term 4.7in SINGLE JACKET OFNG-LS LISTED
FIBOSM06
SINGLE MODE 06 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA P/N
LL0069C5101N1, SPEC. DNL-3224 CABLE DIAMETER .469 IN.
(FORMALLY CALLED A FIBOPT12 ON LTIM01 WHICH WAS ALSO CALLED
A RAD HARD 6 STRAND)
FIBOSM12
SINGLE MODE 12 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL0129C5101N1, SPEC. DNL-3224 CABLE DIAMETER .469 IN.
FIBOSM24
SINGLE MODE 24 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL0249C5101N1, SPEC. DNL-3224 CABLE DIAMETER .469 IN.
FIBOSM48
SINGLE MODE 48 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL0489C5101N1, SPEC.DNL-3224 CABLE DIAMETER .469 IN.
FIBOSM72
SINGLE MODE 72 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL0729C6101N1, SPEC.DNL-3224 CABLE DIAMETER .500 IN.
FIBOSM96
SINGLE MODE 96 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL0969C8101N1, SPEC.DNL-3224 CABLE DIAMETER .571 IN.
FIBOSMPG
REFERS TO SPLICING SINGLE MODE, FACTORY MADE PIGTAILS
ONTO FIBER OPTIC LINES VIA FUSION SPLICING OF ONE END.
PIGTAILS ARE OF VARIOUS LENGTHS BUT TYPICALLY ARE 3 FEET
IN LENGTH AND HAVE A CONNECTOR ON THE OTHER END WHICH HAS
BEEN PREPARED IN THE FACTORY.
FIBOSMPG
FIBER OPTIC, SINGLE MODE, TIGHT BUFFERED STRAND WITH A
FACTORY INSTALLED CONNECTOR ON ONE END AND CUT FIBER ON
THE OTHER FOR FUSION OR MECHANICAL SPLICING. USUALLY PART
OF A MODULE. PIGTAIL TYPICAL LENGTHS ARE 1 OR 2 METERS.
WHEN CODED IN CAPTAR, PIGTAIL LENGTHS ARE ADDED TO FIBER
SHEATH LENGTHS FOR A TOTAL PATH LENGTH.
TYPICAL P/N: SYSTIMAX MODG2-12LC-SM-PT.
FIBSM144
SINGLE MODE 144 STRAND, LOOSE TUBE, LSZH (FRPE), FUJIKURA
P/N LL1449CC101N1, SPEC. DNL-3224 CABLE DIAMETER .720 IN.
8/8/2011
TERM.TYPE
(See Table 3)
88
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
FIB1310
SINGLE MODE, BARE FIBER STRAND. ALWAYS PART OF A LARGER FIBER
CABLE OR SHEATH. 1310 INDICATES 1310 NANOMETER OF OPERATION
BASED ON STANDARD CORNING FIBER SPECIFICATIONS AND COLOR
CODED TO STANDARD FIBER METHODS. STRAND DEFINITIONS REQUIRED
FOR SPLICING INFORMATION PURPOSE AND NO PART NUMBERS ARE
FIOPHYB
HYBRID FIBER OPTIC CABLE, 24 STRANDS MULTIMODE
& 12 STRANDS SINGLE MODE INDOOR/OUTDOOR CONSTRUCTION,
PDR CABLES ARE FLAME RATED AND SUITABLE FOR BOTH INDOOR
AND OUTDOOR INSTALLATIONS 0.539" O.D. MFG BERK-TEK,
P/N #PDR12B036024CB3510/15-012AB1010.
FIOPMM2
MULTI-FIBER, 2 FIBERS, FIBER IS MULTIMODE 62.5 MICRON
CORE, 125 MICRON CLADDING, 250 MICRON COATING, 900 MICRON
BUFFERING, MFR IS AT&T, 0.12 X 0.21" O.D. CODE #1816A,
COMCODE 103 910 170.
FIOPMM3
MULTI-FIBER, MULTIMODE 62.5 MICRON CORE, 125 MICRON
CLADDING, FDDI PLENUM DUPLEX (ZIPCORD). BY FIBER INSTRUMENT
SALES: PART#602-PT-ZC-62AFD.
FIOPMM12
MULTI-FIBER, 12 FIBERS, FIBER IS A MULTIMODE 62.5
MICRON CORE, CABLE CORE IS 'LIGHTPACK' CABLE FILLED CORE.
SHEATH IS STEEL REINFORCED CROSSPLY, 0.42" O.D., MFR.
AT&T, PRODUCT CODE 3DAX-012, COMCODE 105 054 878.
SPECIAL NOTE:THIS CABLE IS TO BE TERMINATED BY QUALIFIED
PERSONNEL ONLY. CABLE AS INSTALLED FOR THE
SLC IS TERMINATED USING 'ST' TYPE CONNECTORS.
USE COLOR CODE TABLE 1Y.
1Y
FIOP-ST,FO-SPL
FIOPMM24
MULTI-FIBER, 24 FIBERS, FIBER IS A MULTIMODE 62.5
MICRON CORE, CABLE CORE IS 'LIGHTPACK' CABLE FILLED CORE.
SHEATH IS RODENT-LIGHTING PROTECTED CROSSPLY, 0.42"
O.D., MFR. AT&T, PRODUCT CODE 3DHX-024, COMCODE
105 080 360. SPECIAL NOTE:THIS CABLE IS TO BE TERMINATED
BY QUALIFIED PERSONNEL ONLY. CABLE AS INSTALLED FOR THE
SLC IS TERMINATED USING 'ST' TYPE CONNECTORS.
USE COLOR CODE TABLE 1Y.
1Y
FIOP-ST,FO-SPL
8/8/2011
FIOP-ST
89
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
FIOPMM48
MULTI-FIBER, 48 FIBERS, FIBER IS A MULTIMODE 62.5
MICRONCORE, CABLE CORE IS 'LIGHTPACK' CABLE FILLED CORE.
SHEATH IS RODENT-LIGHTING PROTECTED CROSSPLY, 0.42"
O.D., MFR. AT&T, PRODUCT CODE 3DHX-048, COMCODE
105 080 480.
SPECIAL NOTE:THIS CABLE IS TO BE TERMINATED BY QUALIFIED
PERSONNEL ONLY. CABLE AS INSTALLED FOR THE
SLC IS TERMINATED USING 'ST' TYPE CONNECTORS.
USE COLOR CODE TABLE 1Y.
1Y
FIOP-ST, FO-SPL
FIOPMM52
MULTI-FIBER, 52 FIBERS, FIBER IS A MULTIMODE 62.5
MICRON CORE, CABLE CORE IS 'LIGHTPACK' CABLE FILLED CORE.
SHEATH IS RODENT-LIGHTING PROTECTED CROSSPLY, 0.42"
O.D., MFR. AT&T, PRODUCT CODE 3DHX-052, COMCODE
105 080 501.
SPECIAL NOTE:THIS CABLE IS TO BE TERMINATED BY QUALIFIED
PERSONNEL ONLY. CABLE AS INSTALLED FOR THE
SLC IS TERMINATED USING 'ST' TYPE CONNECTORS.
USE COLOR CODE TABLE 1Y.
1Y
FIOP-ST, FO-SPL
FOMMDP62
FIBER OPTIC, 62.5/125UM, MULTIMODE, DUPLEX, LSZH.
0.08” O.D.SUPPLIER: MANCO WIRE AND CABLE,
(510)632-3290. P/N: LSZH 2X 62.5/ 2MIL
FOPTMM12
CORNING 12 STRAND MULTIMODE FIBER TRUNK
P/N 012TWZ-T4131D2N 12 FIBER ALTOS LSZH GEL-FREE CABLE
JACKET 50UM PREMIUM ULTRA-BEND 7.5 10GBE UP TO
150 M 3.0/1.0 DB/KM 950 MHZ-KM EMB 12F/TUBE PRINT
IN FT WITH INDUSTRIAL PRINT kg/km (LB/1000ft) 91 (67),
NOMINAL OUTER DIAMETER mm (in)¹ 11.5 (0.46),
MINIMUM BEND RADIUS 11.5 (0.46).
FOSMLCDP
FIBER OPTIC, RISER RATED, SINGLE MODE JUMPER WITH
FACTORY INSTALLED LC DUPLEX STYLE CONNECTORS.
LENGTHS VARY DEPENDING ON THE UNIT PURCHASED.
TYPICAL P/N: SYSTIMAX FPCWLCUC01-R.
FRG59R
SAME CABLE AS RG59R, INSTALLED IN 1/2" ALUMINUM
FLEX CONDUIT FOR ADDED PROTECTION. THIS IS NORMALLY
SPECIFIED AS PART OF A PRE-FABRICATED CABLE ASSEMBLY.
8/8/2011
LC-DUP
90
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
GP330HF
GRANVILLE PHILLIPS, FLEXIBLE CABLE FOR VACUUM. ONE
END IS PRE-WIRED WITH A SPECIAL CONNECTOR, BNC AND AMP4P;
AND THE OTHER END IS PRE-WIRED WITH AN IPI MODEL 9237
CONNECTOR. 0.4" O.D.
HABIA
SIXTY CONDUCTOR, #XX AWG, HV CABLE, FURTHER INFO
PENDING, 1.140" O.D., MFG HABIA P/N 98 W 04.
HC30A
CIRCULAR MULTICONDUCTOR. 20 CONDUCTORS AND 3 COAX CABLES.
0.275" O.D. MFR: CIDTEC.
HD15MF
PRE-FABRICATED COMPUTER CABLE HD-SUB 15 PIN MALE TO FEMALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPLLIERS, IE. "Black Box Corp."
HP-CORD
HP POWER METER CORD. PRE-WIRED WITH SIX PIN
CONNECTORS ON EACH END. ONE END HAS A FEMALE
CONNECTOR, HPJ, ON IT AND THE OTHER END HAS A MALE
CONNECTOR, HPP, ON IT.
HV-CJ
COAXIAL CONNECTOR, MALE, 10KV HV CABLE JACK.
REYNOLDS CAT. NO. 1679096-C
HV-SENS
TRI-AXIAL, SENSOR CABLE, SHIELDED, LSNH, TRAY RATED
HIGH VOLTAGE (3KV) FOR SENSOR, FAST SHUTTER.USED ON VAT
EQUIPMENT/SYSTEM. CONTACT/ORDER INFORMATION: VAT AG,
(925) 944-3570. PART NUMBER: 770CS-99L(X) (X IS LENGTH
IN METERS), THE CABLE(S) WILL BE SUPPLIED BY THE VENDOR
CUSTOM MADE TO LENGTH WITH CONNECTORS ALREADY ATTACHED.
HVSPEC1
SPECIAL HIGH VOLTAGE CABLE, #6 AWG COPPER, 120KV DC
HVK DPS CABLE, KERITE CAT-# 1985, 1.19" O.D., 80 MILS PVC
JACKET.
HV220, LR6#10
HVSPEC2
SPECIAL HIGH VOLTAGE CABLE, THIS CABLE CONSISTS OF
ONE 3KV AC MIL RATED HOOK-UP WIRE, #12AWG, ANIXTER NO.
MIL6878/3-BLE-RED AND ONE 3KV AC MIL RATED HOOK-UP WIRE,
#12AWG, ANIXTER NO. MIL6878/3-BLE-WHITE. THESE TWO WIRES
ARE TO BE INSTALLED IN 1/2" FLEX CONDUIT. 0.875" O.D.
LSY#8, MS5S
8/8/2011
HPJ, HPP
91
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
IG-CABLE
PREWIRED CABLE ASSEMBLY WITH BOTH A MALE AND A
BNC CONNECTOR AT ONE END FOR CONNECTION TO EITHER A
GRANVILLE-PHILLIPS SERIES 270 ION-GAUGE CONTROLLER, OR A
VACUUM GAUGE DROP BOX (WHICH USAGE IS DETERMINED BY
THE DESIGNATED TERMINATION), 0.375" O.D.
NOTE THAT THIS ASSEMBLY MAY BE PRE-FABRICATED USING
TYPE 'ION-GAU' CABLE.
GP-GAU, VG-CON,
VGAUGE
ION-GAU
SPECIAL LLL ION GAUGE CABLE. ONE UNSHIELDED,
TWISTED PAIR OF #14 AWG, TINNED-COPPER CONDUCTORS, TWO
#16 AWG, TINNED-COPPER CONDUCTORS, EACH INDIVIDUALLY
SHIELDED WITH BRAID SHIELDS. THE INSULATION IS RATED AT
GREATER THAN 1000 MEGOHMS PER FOOT OF CABLE. 0.38"
O.D., LRL SPEC. LLL-6145-24464.
IG21, IG22
ION-GAU2
SPECIAL ION GAUGE CABLE. THREE #12 AWG WIRES,
TWISTED TOGETHER WITH A FOIL OVERALL SHIELD AND 1 EA #22
AWG DRAIN WIRE. ONE COAX BELDEN #9311) LAYED IN PARALLEL.
ALL INSULATION USED IS PVC, 600V,. 0.550" O.D. THE MFR. IS
ANIXTER. PART NUMBER UNKNOWN.
AMP14P, IG-RS4
ION-GAU3
SPECIAL ION GAUGE CABLE, CUSTOM COMBINATION. COAX (RG58) AND
MULTICONDUCTOR OVERALL SHIELDED WITH 22GA DRAIN WIRE.
MANUFACTURED BY COAST WIRE AND PLASTIC TECH., INC.
CARSON, CA PN# 02-0144
IG23, IG24
KAPTON
MINIATURE COAXIAL CABLE, KAPTON (POLYIMIDE) INSULATION,
RADIATION RESISTANT, 0.94" O.D. CUSTOM MADE BY W.L. GORE
FOR CAPACITEC, INC.
BNCKAP, MCX
LLNLSUP
LLNL (LAWRENCE LIVERMORE NATIONAL LAB) SUPPLIED CABLE
ASSEMBLY. THIS CUSTOM BUILT CABLE IS PROVIDED BY LLNL.
THIS CABLE ASSEMBLY IS SPECIFICALLY DESIGNED FOR USE ON
LLNL EQUIPMENT.O.D.(OUTSIDE DIAMETER) WILL VARY BASED ON
DESIGN AND MATERIAL BEING USED.
LMR195FR
COAX CABLE, 50 OHM, CAPACITANCE 25.4 PF/FT,
FLEXIBLE LOW LOSS,LOW SMOKE ZERO HALOGEN, TYPE
CMR OR CATVR (OKAY TO BE USED IN CABLE TRAYS
PER NEC ARTICLE 820.154 (D)(E). 0.195 IN. O.D.
MFR: TIMES MICROWAVE, P/N: LMR-195-FR.
8/8/2011
92
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
LMR200X2
COAXIAL CABLE, 50 OHMS, 0.195" O.D.,0.022LB/FT
TIMES MICROWAVE SYSTEMS OR EQUIVALENT. NOMINAL VELOCITY 83%.
CAT. #LMR200.
N200, N200BJ
LMR200FR
COAXIAL CABLE, 50 OHMS, 0.195” O.D., CMR/MPR (PCC-FT4)
NON-HALOGEN, 0.022LB/FT.TIMES MICROWAVE SYSTEMS OR
EQUIVALENT. NOMINAL VELOCITY 83%. CAT. #LMR-200-FR.
N200,N200BJ
LMR240X2
COAXIAL CABLE, 50 OHMS, 0.240" O.D.,0.034LB/FT.
TIMES MICROWAVE SYSTEMS OR EQUIVALENT. NOMINAL VELOCITY 84%
CAT. #LMR-240.
N240, N240BJ
LMR240FR
COAXIAL CABLE, 50 OHMS. 0.240" O.D., CMR/MPR (PCC-FT4)
NON-HALOGEN, 0.034LB/FT. TIMES MICROWAVE SYSTEMS OR SPECIAL
EQUIVALENT. NOMINAL VELOCITY 84%. CAT.#LMR-240-FR.
N240, N240BJ,BNC240
LMR2FRX4
SET OF 4 EACH LMR240FR CABLES, TIMED, MATCHED AND LABELED
FOR BEAM POSITION MONITORS. TREATED AS A SINGLE CABLE.
N240, N240BJ
LMR400X2
LMR400X4
COAXIAL CABLE, 50 OHMS, 0.405" O.D.,0.068LB/FT
TIMES MICROWAVE SYSTEMS OR EQUIVALENT. NOMINAL VELOCITY 85%,
CAT. #LMR400.
N400, N400BJ
LMR400FR
COAXIAL CABLE, 50 OHMS, 0.405" O.D., CMR/MPR (PCC-FT4)
NON-HALOGEN, 0.068LB/FT, TIMES MICROWAVE SYSTEMS OR
EQIVALENT. NOMINAL VELOCITY 85%. CAT. #LMR-400-FR
N400, N400BJ
LMR4FRX4
SET OF 4 EACH LMR400FR COAXIAL CABLES, TIMED, MATCHED AND
LABELED FOR BEAM POSITION MONITORS. TREATED AS A
SINGLE CABLE. OD EA CABLE = 0.405”; ODT= 1.296”.
N400, N400BJ
LMR600
COAXIAL CABLE, 50.0 OHMS, 0.590" O.D., TIMES
FREQUENCY @ 2.5 GHZ, TEMPERATURE RANGE -40C TO +85C
NOMINAL VELOCITY OF PROPAGATION 87% ZCOMAX TECHNOLOGIES
#LMR600.
NM-L600, NF-L600
LMR600FR
COAXIAL CABLE, 50 OHMS, 0.590” O.D., CMR/MPR (PCC-FT4)
NON-HALOGEN, 0.131LB/FT. TIMES MICROWAVE SYSTEMS
OR EQUIVALENT.NOMINAL VELOCITY 87%. CAT.#LMR-600-FR.
N600, N600BJ
LMR6FRX4
SET OF 4 EACH LMR600FR CABLES, TIMED, MATCHED AND
LABELED FOR BEAM POSITION MONITORS. TREATED AS A SINGLE CABLE.
N600, N600BJ
8/8/2011
93
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
NMRI/O
STRAND OF 6-0.14MM SQ. TINNED COPPER EXTRA FLEXIBLE
CONDUCTORS INSULATED POLYMER TWISTED UNDER A POLYESTER
TAPE AND COAXIAL(RG318) WITH STRANDED TINNED COPPER
CONDUCTOR, 0.12MM TINNED COPPER BRAID INSULATION AND PVC
JACKET FLAT CABLE. 250V, 7.5-0.3X5-0.3MM O.D. MULLER
SA CAT.#26512/A.
NOKIA
THREE TWISTED PAIR, #28 AWG, SOLID CONDUCTORS, ZERO
HALOGEN, CERN SPEC #23, TYPE MB06P IEC 332-1. 0.138" O.D.,
MFG. NOKIA KABEL.
NPMM10
CUSTOM MOTION ELECTRONICS ITEM, CUSTOM INTERCONNECT CABLE;
STANDARD FEATURES: MMCABLE CONSTRUCTION, MATERIALS; SPECIAL
FEATURES; 3QM LENGTH; NOTE: INCREASED CABLE LENGTH BEYOND
10M IS NOT RECOMMENDED. USER ASSUMES RESPONSIBILITY FOR LOSS
OF PRODUCT PERFORMANCE DUE TO SIGNAL DEGRADATION.
MUST BE USED WITH MMCABLE-REG MODEL # 10SI40097,
NEWPORT EXPERIENCE/SOLUTIONS
NPMM30
CUSTOM MOTION ELECTRONICS ITEM, CUSTOM INTERCONNECT CABLE;
STANDARD FEATURES: MMCABLE CONSTRUCTION, MATERIALS; SPECIAL
FEATURES; 3QM LENGTH; NOTE: INCREASED CABLE LENGTH BEYOND 10M
IS NOT RECOMMENDED. USER ASSUMES RESPONSIBILITY FOR LOSS OF
PRODUCT PERFORMANCE DUE TO SIGNAL DEGRADATION. MUST BE USED
WITH MMCABLE-REG MODEL # 10SI40097,
NEWPORT EXPERIENCE/SOLUTIONS
PREFAB
CABLE AND CONNECTOR DETAILS ARE PROVIDED BY OUTSIDE VENDOR.
R4010
HIGH VOLTAGE SILICONE LEAD WIRE, UL3239 STYLE, #10 AWG,
40KVDC, O.360" O.D., ROWE INDUSTRIES CAT. #R800-4010.
SOLDER, LRY-8
RADIONET
TWIN LEAD TV CABLE & RADIO CABLE, CELLULINE 300
OHMS, 0.300"X0.400" O.D., BELDEN CAT.#8275.
SOLDER
RG6
COAXIAL CABLE, 75 OHMS, COPPER CENTER WITH SILVER COATING.
RG6-QF
COAXIAL CABLE, 75OHMS COPPER CENTER CONDUCTOR, QUAD SHIELDED,
EXTRA-FLEXIBLE ANIXTER PN# 1362A
8/8/2011
RG-6QS
94
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
RG6U-CN
COAXIAL CABLE, 75 OHMS, 18AWG CENTER COPPER CONDUCTOR
.40 IN., GAS INJECTED FHDPE, SHIELDED, .274 IN. OD,
LSZH JACKET, WEIGHT 42.9LBS/1000FT,UL1685, UL444,
FT4 LOADING,ROHS COMPLIANT, NON PLENUM RATED, CMG-LS,
MAX PULLING TENSION 69LBS. FOR RG6 CONTROL-NET.
RG8
COAXIAL CABLE, RG8/U, 50 OHMS, 0.405" O.D., MIL-C-17D,
BELDEN CAT. #9251, OR ANDREW CAT. #24153.FOAM DIELECTRIC,
OUTER CONDUCTOR IS 100% FOIL, 88% BRAID.
N213, BNC213
RG8A
COAXIAL CABLE, RG8/U, 50 OHMS, DOUBLE SHIELDED, 0.405"
O.D., ANDREW CAT. #241543.
N8-A
RG11A
COAXIAL CABLE, RG-11A/U, 0.405" O.D., 75 OHMS, MIL-C-17D,
BELDEN CAT. #8261.
N11
RG11TRI
TRIAXIAL CABLE, SIMILAR TO RG-11/U, CELLULAR
POLYETHYLENE INSULATION, BLACK JACKET, 0.475" O.D., 75
OHMS, BELDEN CAT. #8233.
N11, N213
RG22
TWINAXIAL CABLE, RG-22A/U, 0.42" O.D., 95 OHMS.
SLAC S/N61-329-006-01.
TX22
RG58
COAXIAL CABLE, RG-58C/U, 50 OHMS, 0.195" O.D., MIL-C-17G,
BLACK NON-CONTAMINATING PVC JACKET.
BELDEN CAT. #8262. 61-329-000-07.
BNC58, TNC58
RG58PLEN
COAXIAL CABLE, RG58/U, PLENUM, 50 OHMS, FOIL AND
BRAID SHIELDS, 0.165" O.D., BELDEN CAT #89907
9907
RG58R
COAXIAL CABLE, RG58A/U OR RG58C/U, 50 OHMS, MIL-C-17D,
0.195"O.D., RED JACKET, 2.5KV MAX., SLAC S/N61-329-007-01.
SHV58,HV58
RG58TR
COAXIAL CABLE, RG58/U, TRAY RATED, 53.5 OHM, .159"
O.D., TEFLON JACKET, ANIXTER/BELDEN #88240.
RG58TLN
COAXIAL CABLE, 50 OHMS,0.235" O.D., XLPE JACKET,
PE DIALECTRIC, NON-HALOGEN, TIMES MICROWAVE SYSTEMS
CAT.# LSSB-RG58, PART # 43030 M17/183-00001
RG59
COAXIAL CABLE, RG59/U OR RG59B/U, 0.242" O.D., 73 OR
75 OHMS MIL SPEC. MIL-C-17D. SLAC S/N 61-329-000-02.
RG59DS
COAX RG59/U DBL CU BRAID.
8/8/2011
BNC59, F59B
FIXED
95
CABLE TYPE
CABLE DESCRIPTION
RG59QS
COAXIAL CABLE, HEADEND RG59/U, QUAD SHIELDED,
0.262" O.D., TIMES FIBER COMMUNICATIONS INC.CAT # 4224OV.
RG59R
COAXIAL CABLE, RG59/U OR RG59B/U, RED JACKET, MIL-C-17D,
75 OHMS, 3.0KV MAX. SLAC S/N61-329-007-02.
See color
CODE TABLE
TERM.TYPE
(See Table 3)
F59QS, F59DS
SHV59J, SHV59P
RG59TLN
COAXIAL CABLE, 75 OHMS, 0.237" O.D., XLPE JACKET,
PE DIALECTRIC, NON-HALOGEN, LIBERTY CABLE CAT. #
RG59-SD-HF-WHT
RG62
COAXIAL CABLE, RG-62/U, 0.242" O.D., 93 OHMS.
SLAC S/N61-329-000-13.
BNC62
RG108A
TWINAXIAL CABLE, RG-108A/U, 0.24" O.D.,78 OHMS.
LEMO2P, TX108
RG142B/U
SMA MALE TO TYPE N MALE, 24" IN LENGTH, P/N
RG142-SMAN-NM-24 SMA MALE TO SMA MALE, 24" IN LENGTH,
P/N RG142-SMAN-SMAN-24. VENDOR:APPLIED SPECIALTIES,
(408) 370-2644, CAMPBELL CALIFORNIA.
RG142SNV
SMA MALE TO TYPE N MALE, 50 OHM, RG142B/U DOUBLE SHIELDED
VENDOR PATCH CABLE.SUGGESTED VENDOR-PATERNACK ENTERPRISES.
PASTERNACK No'S PE3568FL-12, PE3568FL-24, PE3568FL-36,
PE3568FL-48, PE3568FL-60,PE3568FL-72, XX (CUSTOM LENGTH),
WHERE THE LAST TWO DIGITS INDICATE STANDARD LENGTHS IN
INCHES.
RG174
COAXIAL CABLE, RG174/U, 0.100" O.D. 50 OHMS, MIL-C-17F,
SLAC S/N61-329-000-19.
RG174TLN
COAXIAL CABLE, RG174, 0.110" O.D. 50 OHMS, LOW SMOKE ZERO HALOGEN,
PART NUMBER: M17/196-00001.
RG188U
SPECIAL CABLE MADE OF TYPE RG-188U COAX, 50 OHMS.
10 INDIVIDUAL PIECES WITH THE BRAIDED OUTER CONDUCTORS
CONNECTED TOGETHER ON EACH END AND BROUGHT OUT ON
PIN "L". SLAC S/N 61-329-000-16
RG213
COAXIAL CABLE, RG-213/U, BLACK OR GREEN JACKET, 0.405"
O.D., 50 OHMS, MIL SPEC. MIL-C-17F. SLAC S/N61-329-000-06.
RG213R
SAME AS RG213 EXCEPT: RED JACKET, NO SLAC S/N, 7.0KV
MAX., 0.405" O.D., ORDERED FROM MANCO.
8/8/2011
LEMO
HV213,ILP1,ILP2
MS-HVS, HN213
96
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
RG214
COAXIAL CABLE, RG-214/U, 0.425" O.D., 50 OHMS, MIL-SPEC.
MIL-C-17F. SLAC S/N61-329-000-10.
RG214TLN
COAXIAL CABLE, 50 OHMS, 0.425" O.D., XLPE JACKET,
PE DIALECTRIC,NON-HALOGEN, TIMES MICROWAVE SYSTEMS
CAT.# LSSB-RG214 PART # 43038 M17/190-00001
RG214X4
SPECIAL SET OF 4 EACH RG-214/U COAXIAL CABLES, TIMED,
MATCHED, AND LABELED FOR BEAM POSITION MONITORS.
TREATED AS A SINGLE CABLE.
N214
RG218R
COAXIAL CABLE, RG-218/U, RED JACKET, 0.87" O.D., 50
OHMS MIL-SPEC. MIL-C-17D.
N218
RG220
COAXIAL CABLE, RG-220/U, 1.12" O.D., 50 OHMS, MIL-SPEC.
MIL-C-17D.
HV220
RG223
COAXIAL CABLE, RG-223/U, 0.216" O.D., 50 OHMS, MIL-SPEC.
MIL-C-17D.
BNC223, TNC223
N223, SMR223
RG223X4
SPECIAL SET OF 4 EACH RG-223/U COAXIAL CABLES, TIMED,
MATCHED, AND LABELED FOR BEAM POSITION MONITORS.
TREATED AS A SINGLE CABLE. 0.432" O.D.
SMA223, SMR223
N223
RG223X6
SPECIAL SET OF 6 EACH RG-223/u COAXIAL CABLES TIMED,
MATCHED AND LABELED FOR BEAM POSITION MONITORS.
TREATED AS A SINGLE CABLE. 1.296" O.D.
SMA223
RS232-10
10 LINE COMPUTER COMMUNICATION CABLE WITH 25
POSITION "D" CONNECTORS ON EACH END. MFR. INMAC
RWB
A SET OF 3 RADIATION RESISTANT WIRES CONSISTING OF ONE
EACH OF THE FOLLOWING: #20AWG-RED, #16AWG-WHT, #18AWGBLK. XML-125 SERIES, 600V.
SPECCBL
EMI PART#15-955-010.6 CONDUCTORS.
T/C
THERMOCOUPLE, #16 TW SH. MFR: OMEGA#EXPP-K-16.
THICKNET
ETHERNET COAXIAL CABLE, YELLOW PVC JACKET, CL2
RATED, 0.405" 0.D., BELDEN CAT. #9880.
8/8/2011
N214, HN214
BNC214, HV213,
BBJ214, N214JB
N213
97
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
THRM-CU
3 CONDUCTOR, THERMOCOUPLE EXTENSION WIRE, TYPE CU,
26 AWG STRANDED. 0.07” O.D. WIRE INSULATION AND
OVERALL JACKET:GLASS BRAID. RED (NEGATIVE) AND BLACK
(POSITIVE)MFG: OMEGA. P/N: EXGG-3CU-26S.
CABLE TRAY APPLICATION: WHEN ROUTING THIS THEMOCOUPLE WIRE
IN A CABLE TRAY, PROTECT THE WIREOR WIRES USING INNERDUCT
TUBING, MFG: SUPERFLEX, FLEXIBLE SPLIT TUBING
(GRAY – FLAME RETARDANT), ITEM #125-XXXXG.
STRIP
THRM4CU
4 CONDUCTOR, RTD, TYPE CU,
26 AWG STRANDED. 0.07" O.D. WIRE INSULATION AND OVERALL JACKET:
GLASS BRAID. RED (NEGATIVE) AND BLACK (POSITIVE)
MFG: OMEGA. P/N: EXGG-4CU-26S.
STRIP
CABLE TRAY APPLICATION: WHEN ROUTING THIS THERMOCOUPLE WIRE
IN A CABLE TRAY, PROTECT THE WIRE OR WIRES USING INNERDUCT
TUBING, MFG: SUPERFLEX, FLEXIBLE SPLIT TUBING
(GRAY – FLAME RETARDANT), ITEM #125-XXXXG.
TIMES
COAXIAL CABLE, RED JACKET, 7.5KVDC, 26 OHMS, 0.195"
O.D., RADIATION ENVIRONMENT RATING 250 MEGARADS, MFR.
TIMES MICROWAVE SYSTEMS, P/N AA-7406, CODE IDENTIFICATION
#68999. SLAC S/N61-329-007-10.
TMS8481
COAXIAL CABLE, TIMES MICROWAVE, #8481, .0533
O.D.", 22.5 OHMS, BARE COPPER CTR CONDUCTOR, MIL-C-17.
TWC-78-1
TWINAX CABLE, 78 OHMS, 0.150" O.D., 8 TWISTS PER
FOOT, TROMPETER CAT.#TWC-78-1, CABLE GROUP 29.
155-9, 75-29
TWC-78-2
TWINAX CABLE, 78 OHMS, 0.242" O.D., 4 TWISTS PER
FOOT, TROMPETER CAT.#TWC-78-2, CABLE GROUP 9. BLUE JACKET.
75-9
TWC-78FR
TWIN CONDUCTOR 78 OHM, 20AWG, COAXIAL CABLE, LSZH (ZEROHAL)
JACKET, 90% MIN. SHIELD, 18.8 PF/FT, .243 O.D.,(LONG LEAD TIME:
CHEMINAX P/N 7820D0831) P/N: M17-186-00001.
TWC9207N
TWINAX CABLE, ONE PAIR, #20AWG, STRANDED(7X28),
TINNED COPPERCONDUCTOR, POLYETHYLENE INNER JACKET,
DUFOIL, ALUMINUM SHIELD 85% TINNED COPPER BRAID,
LSNH JACKET,.34" O.D.,300 VOLT, BELDEN CAT# 9207NH.
TX227241
TWC-9272
TWINAX CABLE, ONE PAIR, #20 AWG, TINNED COPPER, 93% SHIELD
COVERAGE, .244" O.D.,300 VOLT, BELDEN CAT. # 9272.
42-36
8/8/2011
HV-C, IPVB
BNC-TWN, 75-9
98
See color
CODE TABLE
TERM.TYPE
(See Table 3)
CABLE TYPE
CABLE DESCRIPTION
TWC-9860
TWINAX CABLE, ONE PAIR, #16 AWG, BARE COPPER, 100% SHIELD
COVERAGE, 124 ohm, .440" O.D., 30 VOLT, BELDEN CAT. #9860
75-46
TYPE-C
COAXIAL CABLE, TYPE-C,31 OHM, DIA. 0.195" O.D.,
REYNOLDS INDUSTRIES # 167-2669, PE JACKET, PE DIALECTRIC,
COAXIAL HIGH VOLTAGE STORES ID # 088412
HV58, SHV-C, HV58J
UPS-1400
SMART UPS SIGNALLING RS-232 CABLE,APC SMART-UPS,
PART NUMBER: SU1400RM2U, AC OVT: 6 ACP
DB9
VARIAN
VARIAN UNARMORED, FLEXIBLE CABLE FOR ION PUMPS.
ONE END IS PRE-WIRED WITH A SPECIAL CONNECTOR, IPVA,
AND THE OTHER END IS PRE-WIRED WITH AN AMPHENOL
CONNECTOR, IPA. 0.4" O.D.
IPA, IPVA
VARIAN-A
VARIAN STAINLESS STEEL, ARMORED, FLEXIBLE CABLE
FOR ION PUMPS. ONE END IS PRE-WIRED WITH A SPECIAL
CONNECTOR, IPVA. THE OTHER END SHOULD BE PREPARED FOR AN
IPL3 TERMINATION. 0.4" O.D.
IPL3, IPVA
VSAM
CONSISTS OF TWO 37C24TEF CABLES. EACH CABLE IS
EIGHTEEN PAIRS WITH A DRAIN WIRE, #24AWG TINNED
COPPER, FOAM INSULATED, OVERALL BELDFOIL ALUMINUMPOLYESTER SHIELD, 0.484" O.D. BELDEN P/N 88118.
FOR NON PLENUM APPLICATIONS USE TWO 18PR22OS CABLES.
FOR PIN DETAILS CONTACT P.J. STILES. No DRAWING
NUMBER ASSIGNED AT THIS TIME.
WCC
WATER COOLED CABLE, 1" AL.
WCC-1
WATER COOLED CABLE, 1/2" COPPER.
WPMCOAX
COAXIAL CABLE 50OHM MAX. FREQUENCY 7.5GHZ, FOAMED
POLYETHYLENE,HALOGEN FREE, 12.9MM O.D.,MIN BEND RADIUS
129MM, MAN. P/N HUBER+SUHNER S 10172 B-11 50 OHM,
WEIGHT 15 KG/100METERS, TEMP RANGE -40C +85C
8/8/2011
N-50UV
99
Table 3 - Cable Termination Descriptions
TOOLING NOTE: Unless otherwise specified, the tooling specified below is as follows:
a. Crimp LUG tools are AMP.
b. MS series and other multi-pin connector tools are BURNDY.
c. Coaxial cable trim and crimp tools are KINGS.
--------------------------------------------------------------------------------------------------------------------TERMINAL PLUG CODES:
T (P,C)(A,B…H)xx(A,B,C,D)(A,B,C,D)(N,S,L,D,P)
Terminal Plug Codes Definition:
_ Power, Control
_ (Pitch) A- 2.5MM, B- 3.5, C- 3.81, D- 5.0 E- 5.08, F- 7.5, G- 7.62, H- 10.16
_ xx (# of Position)
_ (Wire Entry) A- Top, B- Left Side, C- Right Side, D- 45 Degrees
_ (Termination Type) A- Screw Top, B- Screw Side, C- Fast Connect, D- Spring Cage
_ (Flange) None, Screw, Self Locking, Direct Mounting, Panel Mount
---------------------------------------------------------------------------------------------------------------------TERM
TERMINATION DESCRIPTION
42-36
TWINAX CONNECTOR, PASTERNACK PE 4236
75-9
TWINAX CONNECTOR, CABLE PLUG, TROMPETER CAT.#PL75-9 FOR
CABLE GROUP 9
VME CRATES
TWC-78-2
75-29
TWINAX CONNECTOR, CABLE PLUG, TROMPETER CAT #PL75-29
FOR CABLE GROUP 29
VME CRATES
TWC-78-1
75-46
TWINAX CONNECTOR TROMPETER TEI-14949, CAT.#PL75-46
TWC-9860
155-29
TWINAX CONNECTOR, CABLE PLUG, TROMPETER CAT #PL155-29,
FOR CABLE GROUP 29.
TWC-78-1
972411P
THE CONNECTOR IS FORMERLY, MIL-C-5015 NOW 97 SERIES
PART NO. 97-3106A-24-11P AS WELL AS 97-3106A-24-11S
9 CONTACT CONNECTOR 6 #12AWG AND 3 #8AWG WIRES,OLIVE
DRAB METAL SHELL.
972411S
THE CONNECTOR IS FORMERLY, MIL-C-5015 NOW 97 SERIES
PART NO. 97-3106A-24-11P AS WELL AS 97-3106A-24-11S
9 CONTACT CONNECTOR 6 #12AWG AND 3 #8AWG WIRES,OLIVE
DRAB METAL SHELL.
8/8/2011
APPLICATION
USED ON CABLE TYPE
TWC-9272
100
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
9907
COAXIAL CONNECTOR, BNC CABLE PLUG, BNC9907HPC, AMP
P/N 2-221128-7 USE AMP CRIMPING TOOL 58433-2
WITH DIE 58436-1.
THINNET
RG58PLEN
3M16S
SIXTEEN PIN CONNECTOR, FEMALE FLAT RIBBON CABLE PLUG,
POLARIZING SLOTS, 3M P/N #3452-6600,NEWARK CAT.#46F4657.
3M20S
TWENTY PIN CONNECTOR, FEMALE FLAT RIBBON CABLE PLUG,
POLARIZING SLOTS, 3M P/N#3421-6000 NEWARK CAT.P/N#46F8438.
3M40S
FORTY PIN CONNECTOR, FEMALE FLAT CABLE PLUG, 3M CAT.
#3417-6640, SLAC S/N59-299-165-40.
3M50S
FIFTY PIN CONNECTOR, FEMALE FLAT CABLE PLUG.
16FERLS
SINGLE INSULATED WIRE FERRULES CONNECTOR, 16AWG
MANUFACTURER ABB INC.P/N 30445703.
16FERLT
TWIN INSULATED WIRE FERRULES CONNECTOR, 16AWG
MANUFACTURER ABB INC.P/N 30456305.
18FERLS
SINGLE INSULATED WIRE FERRULES CONNECTOR, 18AWG
MANUFACTURER ABB INC.P/N 30445602.
18FERLT
TWIN INSULATED WIRE FERRULES CONNECTOR, 18AWG
MANUFACTURER ABB INC.P/N 30456103.
20FERLS
SINGLE INSULATED WIRE FERRULES CONNECTOR, 20AWG
MANUFACTURER ABB INC.P/N 30445501.
20FERLT
TWIN INSULATED WIRE FERRULES CONNECTOR, 20AWG
MANUFACTURER ABB INC.P/N 30455911.
500MCSI
MULTI-CONTACT SOCKET WITH BAYONET LOCKING AND CRIMP SLEEVE,
P/N KBT16BV-NS/M50-240. USE CRIMP TOOL ELPRESS P/N V1311C
WITH DIE 13CB30. NOTE: CONNECTORS ARE ALL THE SAME. ORDER
APPROPRIATE FERREL AND NUT FOR WIRE TYPE AND SIZE OTHER
THAN 500TLSNH.
535MCS
SLEEVE, CRIMP, MULTI-CONTACT P/N H240N/M20, WITH MODIFIED
THREADED SOCKET P/N B25N. USE CRIMP TOOL ELPRESS P/N
V 1311C WITH 13CB30 DIE SET.SECURE SLEEVE TO SOCKET,
TIGHTEN TO 12 FT/LBS OR 52NM. COVER SOCKET/SLEEVE AND
3 1/2" OF CABLE WITH HEAT SHRINK TUBING THOMAS & BETTS
P/N HS500-1000. "DO NOT USE WITH NEW INSTALLATIONS".
8/8/2011
40C24OS
500TLSNH
SPPS CHICANE BEND
101
TERM
TERMINATION DESCRIPTION
APPLICATION
AC-BMP
BUSINESS MACHINE PLUG. AC POWER LINE CONNECTOR,
10AMP,250V, APPLIANCE INLET, STRAIGHT ENTRY, SCHURTER,
MALE CONNECTOR.
AC SERVICE
AC-BMS
BUSINESS MACHINE PLUG. AC POWER LINE CONNECTOR,10AMP,
250V, APPLIANCE INLET, STRAIGHT ENTRY, FEMALE CONNECTOR.
AC SERVICE
ACJBX
120VAC JUNCTION BOX WITH 1 OR 2 ACR CONNECTORS.
AC SERVICE
3C16/3V, 3C16FLX
ACM20P
AC POWER PLUG, 208V, 20 AMPS, 3 PHASE, 4 WIRE.
DECONTACTOR (RATED TO BE DISCONNECTED WITH
POWER STILL ON IF NECESSARY),
LOTO (LOCKOUT TAGOUT SAFETY FEATURE),
MFG: MELTRIC CORPORATION, MFG SERIES: DSN20,
MFG P/N:63-18163.
SEE MELTRIC CATALOGUE FOR OTHER ACCESSORIES.
ACM60P
AC POWER PLUG, 208V, 60 AMPS, 3 PHASE, 4 WIRE.
DECONTACTOR (RATED TO BE DISCONNECTED WITH
POWER STILL ON IF NECESSARY),
LOTO (LOCKOUT TAGOUT SAFETY FEATURE),
MFG: MELTRIC CORPORATION, MFG SERIES: DSN60,
MFG P/N:63-68163.
SEE MELTRIC CATALOGUE FOR OTHER ACCESSORIES.
ACP
AC MALE CONNECTOR, 3 WIRE, 15A, PARALLEL UGRD,
NEMA 5-15P, HUBBEL 5266C, SLAC P/N58-299-202-07.
AC SERVICE
3C16/3V, 3C16FLX
3C14FLX
ACP20
AC POWER CONNECTOR, 120/208V, 20 AMPS, 4 POLE, 5 WIRE
GROUNDING, 3 PHASE Y, NEMA #L21-20R, MFR. HUBBELL,
CAT-# 2513 OR EQUIVALENT.
ACP22
AC POWER PLUG, TWIST-LOCK, 480V, 30 AMPS, 4 POLE, 5 WIRE
GROUNDING, 3 PHASE Y, NEMA #L22-30P, MFR. HUBBELL,
CAT-# 2821 OR EQUIVALENT.
ACR
AC FEMALE CONNECTOR, RECEPTACLE BODY, 3 WIRE, 20A IT SLOT,
HUBBEL 5369C, NEMA 5-20R, SLAC P/N 58-299-403-10.
8/8/2011
USED ON CABLE TYPE
4C8TYR
AC SERVICE
3C14FLX, 3C16FLX
102
TERM
TERMINATION DESCRIPTION
AMP4P
FOUR PIN CONNECTOR, MALE CIRCULAR PLUG, SHELL SIZE 11-4,
AMP CAT. #206429-1,BACK SHELL, AMP CAT. #206062-3. USE THE
FOLLOWING PINS AS APPROPRIATE. USE CRIMPING TOOL AMP CAT.
#90277-1.
16-18 AWG AMP CAT. #66099-3
20-22 AWG AMP CAT. #66400-3
24-26 AWG AMP CAT. #66107-3
2PR22OS
AMP4S
FOUR PIN CONNECTOR, FEMALE CIRCULAR PLUG, SHELL SIZE 11-4,
AMP CAT. #206060-1, BACK SHELL AMP CAT. #206062-3. USE THE
FOLLOWING PINS AS APPROPRIATE. USE CRIMPING TOOL AMP CAT.
#90277-1.
16-18 AWG AMP CAT. #66101-3
20-22 AWG AMP CAT. #66399-3
24-26 AWG AMP CAT. #66109-3
2PR22OS
AMP8P
EIGHT PIN CONNECTOR, MALE CIRCULAR PLUG, SHELL
SIZE 11-8, AMP CAT. #206434-1 BACK SHELL AMP
CAT. #206062-3. USE THE FOLLOWING PINS AS
APPROPRIATE. USE CRIMPING TOOL AMP CAT #90277-1.
16-18 AWG AMP CAT. #66099-3
20-22 AWG AMP CAT. #66400-3
24-26 AWG AMP CAT. #66107-3
4PR22OS
AMP8S
EIGHT PIN CONNECTOR, FEMALE CIRCULAR PLUG, SHELL
SIZE 11-8, AMP CAT. #205838-1 BACK SHELL AMP
CAT. #206062-3. USE THE FOLLOWING PINS AS
APPROPRIATE. USE CRIMPING TOOL AMP CAT. #90277-1.
16-18 AWG AMP CAT. #66101-3
20-22 AWG AMP CAT. #66399-3
24-26 AWG AMP CAT. #66109-3
4PR22OS
AMP9F
NINE PIN CONNECTOR, SERIES 1 LIGHTWEIGHT FEMALE
CIRCULAR PLASTIC CONNECTOR(CPC). AMP CAT#206708-1
4PR24FRP
AMP9S
NINE PIN CONNECTOR, FEMALE CIRCULAR PLUG, SHELL
SIZE 11-9, AMP CAT. #206485-1, BACK SHELL AMP
CAT. #206062-3. USE THE FOLLOWING PINS AS
APPROPRIATE. USE CRIMPING TOOL AMP CAT. #90277-1.
16-18 AWG AMP CAT. #66101-3
20-22 AWG AMP CAT. #66399-3
24-26 AWG AMP CAT. #66109-3
8/8/2011
APPLICATION
MAGNET MOVERS
USED ON CABLE TYPE
9C18J
103
TERM
TERMINATION DESCRIPTION
AMP9SA
NINE PIN CONNECTOR, FEMALE CIRCULAR PLUG, SHELL
SIZE 13-9, AMP CAT. #206708-1, BACK SHELL AMP
CAT. #206966-1. USE THE FOLLOWING PINS AS APPROPRIATE.
USE CRIMPING TOOL AMP CAT. #90277-1.
16-18 AWG AMP CAT. #66101-3
20-22 AWG AMP CAT. #66399-3
24-26 AWG AMP CAT. #66109-3
AMP12P
CONNECTOR, 12 PIN MALE, AMP CAT-# 204740-2 SLAC
S/N59-299-162-52.
CABLE CLAMP AMP CAT #205083-1.USE CRIMPING TOOL
AMP#584-95-1.USE THE FOLLOWING PINS AS APPROPRIATE:
#20-24 AWG, #203816-4 (LOOSE), S/N59-299-805-51.
#20-24 AWG, #203816-2 (REELED).
#26-30 AWG, #203874-4 (LOOSE), S/N59-299-805-52.
#26-30 AWG, #203874-2 (REELED).
AMP14P
FOURTEEN PIN CONNECTOR, MALE, PLASTIC SHELL, AMP
CAT #206044-1 WITH CABLE CLAMP KIT AMP CAT. #206070-1.
USE CRIMPING TOOL AMP #584-95-1.
USE THE FOLLOWING PINS,AS APPROPRIATE
#32-30 AWG AMP CAT #201555-1
#28-24 AWG AMP CAT #201334-1
#24-20 AWG AMP CAT #201330-1
#18-16 AWG AMP CAT #202507-1
#14
AWG AMP CAT #201570-1
AMP14SR
FOURTEEN PIN CONNECTOR, FEMALE, PLASTIC SHELL,
AMP CAT #206043-1, CABLE CLAMP KIT AMP CAT #206070-1.
USE THE FOLLOWING PINS, AS APPROPRIATE. USE CRIMPING
TOOL AMP. #584-95-1.
#32-30 AWG AMP CAT #201554-1
#28-24 AWG AMP CAT #201332-1
#24-20 AWG AMP CAT #201328-1
#18-16 AWG AMP CAT #202508-1
#14
AWG AMP CAT #201568-1
8/8/2011
APPLICATION
USED ON CABLE TYPE
104
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
AMP24P
TWENTY-FOUR POSITION RECEPTACLE, MALE, AMP
CAT-# 204742-2 SLAC P/N59-299-162-54, WITH CABLE CLAMP
#205083-2, S/N59-299-162-94. USE THE FOLLOWING PINS, AS
APPROPRIATE: USE CRIMPING TOOL AMP #584-95-1.
#20-24 AWG, #203816-4 (LOOSE), S/N59-299-805-51.
#20-24 AWG, #203816-2 (REELED), S/N59-299-805-53.
#26-30 AWG, #203874-4 (LOOSE), S/N59-299-805-52.
#26-30 AWG, #203874-2 (REELED), S/N59-299-805-54.
MPS TOROIDS
6PR24IS
WHEN USED WITH 6PR24IS CABLE FOR MPS TOROIDS, WIRE AS FOLLOWS:
PAIR#
1
1
1
2
2
2
3
3
3
WIRE#
A
B
SHIELD
A
B
SHIELD
A
B
SHIELD
PIN#
A1
B1
C1
A2
B2
C2
A3
B3
C3
PAIR#
4
4
4
5
5
5
6
6
6
WIRE#
A
B
SHIELD
A
B
SHIELD
A
B
SHIELD
PIN#
A4
B4
C4
A5
B5
C5
A6
B6
C6
AMP36P
THIRTY-SIX POSITION PLUG ASSEMBLY, AMP 204744-2, SLAC
STANDARD CAMAC CABLE PLUG, SLAC S/N59-299-162-55, WITH
CABLE CLAMP #205083-3, S/N59-299-162-95.
USE CRIMPING TOOL AMP #584-95-1. USE THE FOLLOWING PINS,
AS APPROPRIATE:
#20-24 AWG, #203816-4 (LOOSE), S/N59-299-805-51.
#20-24 AWG, #203816-2 (REELED), S/N 59-299-805-53.
#26-30 AWG, #203874-4 (LOOSE), S/N59-299-805-52.
#26-30 AWG, #203874-2 (REELED), S/N59-299-805-54.
AMP37P
THIRTY-SEVEN PIN CONNECTOR, MALE, CPC, AMP CAT.
#206305-1 BACK SHELL CABLE CLAMP AMP CAT. #206138-1,
#16 AWG, PINS AMP CAT. # 40-102C. USE HAND CRIMPING
TOOL AMP CAT. #90067.
AMP37S
THIRTY-SEVEN PIN CONNECTOR, FEMALE, CPC, AMP CAT.
#206150-1 BACK SHELL CABLE CLAMP AMP CAT. #206138-1,
#16 AWG, PINS AMP CAT. # 40-103C. USE HAND CRIMPING
TOOL AMP CAT. #90067.
8/8/2011
18PR22OS, RG58
105
TERM
TERMINATION DESCRIPTION
AMP48P
FORTY-EIGHT POSITION PLUG ASSEMBLY, AMP 204733-2,
SLAC STANDARD CAMAC CABLE PLUG, SLAC S/N59-299-162-06,
WITH CABLE CLAMP #205083-4, S/N59-299-162-96.
USE CRIMPING TOOL AMP #584-95-1. USE THE FOLLOWING PINS,
AS APPROPRIATE:
#20-24 AWG, #203816-4 (LOOSE), S/N59-299-805-51.
#20-24 AWG, #203816-2 (REELED),S/N59-299-805-53.
#26-30 AWG, #203874-4 (LOOSE),S/N59-299-805-52.
#26-30 AWG, #203874-2 (REELED),S/N59-299-805-54.
AMP50P
FIFTY POSITION MALE PLUG ASSEMBLY, SOLDER
CONNECTIONS, AMP P/N 229912-1
DISABLE/ALARM
25PR24OS
AMP50S
FIFTY POSITION FEMALE PLUG ASSEMBLY, SOLDER
CONNECTIONS, AMP P/N 229913-1
DISABLE/ALARM
25PR24OS
AMPH2
TWO PIN CONNECTOR, 1 MALE, 1 FEMALE. BNC POLARIZED
CONTACTS. AMPHENOL NO. 31-224.
AMPH4
FOUR PIN CONNECTOR, AMPHENOL NO. 206136-1.USE CRIMPING
TOOL, AMP NO. 69710-1. WIRE IN COLOR CODE SEQUENCE.
SEE THE WIRE TYPE FOR THE COLOR CODE.
AMPH7S
SEVEN PIN CONNECTOR, FEMALE, ISI/MDC P/N 992-1002.
SEE THE WIRE TYPE FOR THE COLOR CODE. SOLDER
CONNECTIONS.
AMPH8S
EIGHT PIN CONNECTOR, OCTAL TUBE SOCKET AMPHENOL
NO. 78-S8, USE AMPHENOL CAP NO. 86-3-24. SEE THE
WIRE TYPE FOR THE COLOR CODE. SOLDER CONNECTIONS.
AMPL2
CABLE PLUG, TWO CONDUCTOR IN LINE, MATE-N-LOCK
CONNECTOR, AMP P/N 1-480698-0.
USED FOR REPEATER CHASSIS J2.
BBJ58
COAXIAL CONNECTOR, BNC BULKHEAD JACK.
TYCO PART # 1-1337434-0. SEE TYCO DRAWING # C-1337434
( http://www.farnell.com/datasheets/23770.pdf )
FOR STRIPPING DIMENSIONS.
USE TYCO HAND TOOL 9-1478240-0.
USE TYCO DIE SET 9-1478242-0.
8/8/2011
APPLICATION
USED ON CABLE TYPE
18PR22OS, 30PR26OS
RG58
106
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
BBJ59
COAXIAL CONNECTOR, BNC BULKHEAD JACK, KINGS
P/N'S 19-62, KC19-182 OR KC19-89,
SLAC S/N59-299-014-66. TRIM CODE 405,
USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2002.
SLCNET
RG59DS
BBJ214
COAXIAL CONNECTOR, N BULKHEAD JACK, KINGS P/N KC-19-232,
SLAC S/N59-299-014-71. USE TRIM CODE 411, USE KINGS
CRIMPING TOOL KTH-1000 WITH DIE KTH-2004
PANEL MOUNTS
RG214
BNC58
COAXIAL CONNECTOR, BNC CABLE PLUG, UG-88D/U. KINGS CAT.
NO. KC-59-290 OR KC-59-291, SLAC S/N59-299-014-51. USE
KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2001 AND TRIM
CODE 401.
RF AND FAST
SIGNALS
RG58
BNC59
COAXIAL CONNECTOR, BNC CABLE PLUG, UG-260B/U. KINGS CAT.
NO. KC-59-293 OR KC-59-294, SLAC S/N59-299-014-52. USE
KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2002 AND TRIM
CODE 401.
TV
RG59, RG59DS
BNC62
SAME CONNECTOR AS BNC59. SAME TOOLING AND TRIM CODE.
SSC FASTLINK
RG62
BNC174
COAXIAL CONNECTOR, BNC CABLE PLUG, KINGS #KC-59-557-M06
SLAC S/N59-299-014-63, TRIM CODE 406. USE CRIMPING TOOL
KTH-1000 WITH SIE KTH-2032.
BNC213
COAXIAL CONNECTOR, BNC CABLE PLUG. KINGS CAT. NO.
KC-59-86, USE KINGS CRIMPING TOOL KTH-1000 WITH DIE
KTH-2003 AND TRIM CODE 209A.
RF AND FAST
SIGNALS
RG213, RG8
BNC214
COAXIAL CONNECTOR, BNC CABLE PLUG. KINGS CAT. NO.
KC-59-85, USE KINGS CRIMPING TOOL KTH-1000 WITH DIE
KTH-2004 AND TRIM CODE 209A
RF AND FAST
SIGNALS
RG214
BNC223
COAXIAL CONNECTOR, BNC CABLE PLUG. KINGS CAT. NO.
KC-59-80 OR KC-59-162, SLAC S/N. 59-299-014-65.
USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2001
AND TRIM CODE 401.
RF AND FAST
SIGNALS
RG223
BNC240
IT IS BASICALLY A BNC MALE CONNECTOR WHICH ATTACHES TO AN
LMR240FR CABLE.THE DESCRIPTION IS COAXIAL CONNECTOR TYPE
BNC MALE PLUG. TIMES MICROWAVE,SYSTEMS CATALOG
#TIMTC240BM-A CONNECTOR, BNC MALE CRIMP FOR LMR240,
LMR240FR.
8/8/2011
LMR240, LMR240FR
107
TERM
TERMINATION DESCRIPTION
BNCKAP
COAXIAL CONNECTOR, BNC CABLE PLUG FURNISHED WITH
KAPTON CABLE TYPE ONLY.
BNC-TWN
TWIN BNC CONNECTOR PLUG, MANUFACTURED BY TYCO
ELECTRONICS,(OLD P/N: CAT. 1307191). Use P/N: 5332225.
BP(-ccc)
BANANA PLUG, WITH COLORED PLASTIC INSULATING SHELL.
WHERE (-ccc) IS DEFINED, THE SHELL IS TO BE THE
INDICATED COLOR. IF UNDEFINED, ANY COLOR MAY USED.
SLAC S/N 59-299-698-(nn), WHERE (nn) IS SELECTED
FOR THE DESIRED COLOR.
BP&BJ
BANANA PLUG (MALE) AND BANANA JACK (FEMALE) SLAC
P/N 59-299-698-(nn)& SLAC P/N 59-299-699-(nn). WHERE
(nn)IS SELECTED FOR THE DESIRED COLOR.
BP-01
TERMINATION BP ABOVE, WITH (ccc) SELECTED TO MATCH THE
WIRE COLOR(S) OF THE INDICATED CABLE.
BP-02
TERMINATION BP ABOVE, USING THE FOLLOWING COLORS, AND
CONNECTED TO THE MATCHING COLORED JACKS ON THE
INDICATED CHASSIS.
BLACK WIRE WITH A BLUE BANANA PLUG (SLAC S/N 59-299-698-07).
WHITE WIRE WITH A BLACK BANANA PLUG (SLAC S/N 59-299-698-05).
SHIELD WIRE WITH A GREEN BANANA PLUG (SLAC S/N 59-299-698-06).
BPD-01
BANANA PLUG DUAL, BLACK COLORED PLASTIC INSULATING SHELL.
SLAC S/N 59-299-701-01. MFG: POMONA. MFG P/N: 1330-0
BSB
CONNECTOR, BUTT SPLICE, BLUE, INSULATED,
FOR #14 TO #16AWG.WIRE, AMP CAT.#320562,
SLAC S/N59-294-770-07. USE HAND CRIMPING TOOL
AMP #59250.
BSR
CONNECTOR, BUTT SPLICE, RED, INSULATED,
FOR #18 TO #22 AWG. WIRE,AMP CAT.#320559,
SLAC S/N59-294-770-04. USE HAND
CRIMPING TOOL AMP #59250.
BSY
CONNECTOR, BUTT SPLICE, YELLOW, INSULATED,
FOR #10 TO #12 AWG.WIRE, AMP CAT.#320570,
SLAC S/N59-294-770-09. USE HAND
CRIMPING TOOL AMP #59239-4R.
8/8/2011
APPLICATION
USED ON CABLE TYPE
KAPTON
SOLID STATE
SUB-BOOSTER
TRIGGERS
TWC-78FR
3C16/3V
2C16OS, 1PR20OS
3PR24OS
108
TERM
TERMINATION DESCRIPTION
BS1
CONNECTOR, BUTT SPLICE FOR #1 AWG WIRE,
UNINSULATED, COPPER, LONG BARREL,
BURNDY CAT. #YS1C. USE CRIMPING TOOL
BURNDY #MY29-11 WITH DIE BURNDY #U/CRT.
BS2
CONNECTOR, BUTT SPLICE FOR #2 AWG WIRE, UNINSULATED,
COPPER, LONG BARREL. MFG: THOMAS AND BETTS. P/N:54507.
BS2/0
CONNECTOR, BUTT SPLICE FOR 2/0 AWG WIRE,
UNINSULATED,COPPER, LONG BARREL,COLOR-KEYED
CAT.#54810. USE CRIMPING TOOL
"COLOR-KEYED TBM8" WITH DIE "COLOR-KEYED #13462".
BS35ALC
CONNECTOR, BUTT SPLICE, 350 KCMIL, ALUMINUM TO COPPER, UNINSULATED,
CAN BE USED TO SPLICE AL/CU FOR WIRE RANGE OF 2/0-350 KCMIL
WHEN USED WITH “VERSA-CRIMP” CRIMPER.
MFG: HUBBELL-ANDERSON, MFG P/N: VACS-350.
LINK: http://www.hubbell.com.mx/pdfs/anders.pdf PAGE: A-55
BS4
CONNECTOR, BUTT SPLICE FOR #4 AWG WIRE,
UNINSULATED, COPPER, LONG BARREL, BURNDY
CAT. #YS4C. USE CRIMPING TOOL
BURNDY #MY29-11 WITH DIE BURNDY #U4CRT.
BS4/0
CONNECTOR, BUTT SPLICE FOR 4/0 AWG WIRE,
UNINSULATED,COPPER, LONG BARREL, COLOR-KEYED
CAT.#54812. USE CRIMPING TOOL
"COLOR-KEYED TBM8" WITH DIE
"COLOR-KEYED #13463".
BS8
CONNECTOR, BUTT SPLICE FOR #8 AWG WIRE, UNINSULATED,
COPPER, LONG BARREL. MFG: THOMAS AND BETTS. P/N: 54504.
BULLET
BULLET WIRE TERMINATION, SLAC S/N59-294-644-01,
BURNDY CAT. #AYH-18-H2. USE HAND CRIMPING TOOL
BURNDY #M8ND WITH DIE BURNDY #N18HCT.
BUR20S
CONNECTOR, 20 PIN FEMALE, RECTANGULAR PLUG,
BURNDY P/N MS20PM-824S. INCLUDES HOOD,
SKIRT AND JACK SCREWS.
C41SW
COAXIAL CONNECTOR,MALE,PLATED,TYPE N,
ANDREWS PN F1PNM-14.
C41SWS
COAXIAL CONNECTOR, SMA MALE, ANDREWS PN F1PSM.
8/8/2011
APPLICATION
SUMP PUMP ALARM
USED ON CABLE TYPE
4C18OS
109
TERM
TERMINATION DESCRIPTION
CAN4P
FOUR PIN CONNECTOR, MALE, SOLDER TERMINATIONS,
CANNON CAT #WK-4-22C.
CAN4S
FOUR PIN CONNECTOR, FEMALE, SOLDER TERMINATIONS,
CANNON CAT #WK-4-21C.
CAN12S
TWELVE PIN CONNECTOR, FEMALE, SOLDER
TERMINATIONS, CANNON CAT #GK1221
RG214
CAN24S
TWENTY-FOUR PIN CONNECTOR, FEMALE, BAYONET
SERIES, SOLDER PINS, USE HEAT SHRINK TUBING OVER EVERY
OTHER SOLDER POCKET FOR INSULATION. CANNON-ITT CAT.
#CA3106F24A-24S.
12C12/3V
CATON13
THIRTEEN PIN CIRCULAR PLUG WITH CABLE CLAMP,
CATON PART #3106A-CC18-135.
CED-30
CARD EDGE CONNECTOR, DOUBLE ROW, 30-POINT FEMALE.
CINCH-JONES P/N 250-50-38A-30.
CIN12S
TWELVE PIN FEMALE CONNECTOR, CINCH P/N 9142,
USE HOOD P/N 60332.
CIN20S
TWENTY PIN FEMALE CONNECTOR, CINCH P/N 9325,
USE HOOD P/N 60326.
CUT
CONNECTOR TYPE UNKNOWN AT THIS TIME, TERMINATION IS BE
DONE BY OTHER LATER, PULL CABLE TO ORIGIN/DESTINATION
IN LEAVE TWO FEET AT THE EXIT.
D14S
FOURTEEN PIN FEMALE "D" CONNECTOR AMPHENOL P/N
57-60140 ASSEMBLE WITH CABLE HOUSING (BACK SHELL) AND
SPRING LATCH PLATE 17-529
DAC15P
CONNECTOR, 15 PIN MALE, CANNON "D" SERIES
SUBMINIATURE, CANNON CAT.#DAU-15P SLAC
P/N59-299-160-01.
DAY-20
TWENTY POSITION CARD EDGE SPECIAL CONNECTOR,
DAYTRONICS PN #60322 WITH DUAL CABLE CLAMPS AND SOLDER
TYPE PINS. REFERENCE DRAWING BD-129-691-03
8/8/2011
APPLICATION
USED ON CABLE TYPE
3PR24IS
LVDT
3PR24IS, 2PR24IS
4C20OS
110
TERM
TERMINATION DESCRIPTION
DAY-50
FIFTY POSITION CARD EDGE CONNECTOR ADAPTED BY PC BOARD
TO A 17 SCREW CONNECTING STRIP. TOP TO BOTTOM:
1-EXT.COLLECTOR POWER, 2-ISOLATED COMMON,3/17-CH's 0-15.
DAYTRONICS PN #XXXXXXX
DB9MFV
PRE-FABRICATED COMPUTER CABLE D-SUB 9 PIN MALE TO FEMALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPLLIERS, IE. "FRY'S ELECTRONICS"
DB9MMV
PRE-FABRICATED COMPUTER CABLE D-SUB 9 PIN MALE TO MALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPLLIERS, IE. "FRY'S ELECTRONICS"
DB9P
NINE PIN CONNECTOR, MALE, "D" SUBMINIATURE
RECTANGULAR, ITT CANNON CAT. #DEU-9P,
SLAC S/N59-299-160-05,HOOD ITT CANNON
CAT. #DE24657 SLAC S/N59-299-160-50.
LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1
2PR22OS
DB9S
NINE PIN CONNECTOR, FEMALE, "D" SUBMINIATURE
RECTANGULAR, ITT CANNON CAT. #DEU-9S.
SLAC S/N59-299-160-06, HOOD ITT CANNON
CAT. #DE24657, SLAC S/N59-299-160-50.
LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
5PR28F, 6PR22OS
DB15P
FIFTEEN PIN CONNECTOR, MALE, "D" SUBMINIATURE
RECTANGULAR, ITT-CANNON CAT. #DAU15P, SLAC
S/N59-299-160-01, HOOD ITT CANNON CAT. #DA24658,
SLAC S/N59-299-160-51.LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
DB15S
FIFTEEN PIN CONNECTOR, FEMALE,"D" SUBMINIATURE
RECTANGULAR,ITT-CANNON CAT. #DAU15S, SLAC
S/N 59-299-160-02, HOOD ITT-CANNON CAT.#DA24658.
SLAC S/N59-299-160-51.LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
DB15S-HD
DB15 HIGH DENSITY SOCKET - THE 15-PIN CONNECTOR
WILL HAVE 3 ROWS OF 5 SOCKETS.CONNECTOR IS TYPICALLY FOUND
FOR VIDEO CABLE TO COMPUTER MONITORS.
MFG:STARTECH COMPUTER PRODUCTS, MFG P/N:C15HPSF
8/8/2011
APPLICATION
USED ON CABLE TYPE
12PR22OS
8PR28F
111
TERM
TERMINATION DESCRIPTION
DB25MFV
PRE-FABRICATED COMPUTER CABLE D-SUB 25 PIN MALE TO FEMALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPLLIERS, IE. "FRY'S ELECTRONICS"
DB25MMV
PRE-FABRICATED COMPUTER CABLE D-SUB 25 PIN MALE TO MALE
WITH MOLDED PLUG ENDS. WIDELY AVAILABLE FROM COMPUTER
RETAILERS AND PART SUPPLIERS, IE. "FRY'S ELECTRONICS"
DB25P
TWENTY-FIVE PIN CONNECTOR, MALE, "D"
SUBMINIATURE RECTANGLE, ITT-CANNON CAT. #DBC-25P, SLAC
S/N59-299-160-03, HOOD ITT-CANNON CAT. DB24659, SLAC
S/N59-299-160-52. LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
26C24OS
DB25S
TWENTY-FIVE PIN CONNECTOR, FEMALE, "D"
SUBMINIATURE RECTANGLE, ITT-CANNON CAT. #DBU-25S, SLAC
S/N59-299-160-04, HOOD ITT-CANNON CAT. #DB24659, SLAC
S/N59-299-160-52. LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1. FOR 18-22AWG WIRE, USE THE
FOLLOWING DIGIKEY SOCKETS: A31900TR-ND
26C24OS
DB37P
THIRTY SEVEN PIN CONNECTOR MALE "D" SUBMINIATURE RECTANGLE.
DB37S
THIRTY SEVEN PIN CONNECTOR FEMALE "D" SUBMINIATURE RECTANGLE.
DB50
50 PIN AMPLITE HDP-20 (DB50) SHIELDING HARDWARE ENCLOSER KIT
AMP PART NUMBER 747959-1 (1 REQUIRED)
HDP-20 SERIES STEPPED FERRULE (0.375 TO 0.432 DIA CABLE OD)
AMP PART NUMBER 747580-4 (1 REQUIRED)
PIN CONTACT - 24 TO 28 AWG - 30 MICRON GOLD FINISH
AMP PART NUMBER 66505-9 (50 REQUIRED)
DB52P
FIFTY-TWO PIN CONNECTOR, MALE, "D" SUBMINIATURE
RECTANGULAR, ITT-CANNON,CAT. #2DB52P, SLAC S/N59-299-160-07.
HOOD ITT-CANNON CAT. #DD24661. LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
18PR22OS
DB52S
FIFTY-TWO PIN CONNECTOR, FEMALE, "D"
SUBMINIATURE RECTANGULAR, ITT-CANNON CAT. #2DB52S,
SLAC S/N59-299-160-08, HOOD ITT-CANNON CAT. #DD24661.
LOCK DEVICES S/N59-299-160-74.
USE CRIMPING TOOL AMP #584-95-1.
18PR22OS
8/8/2011
APPLICATION
USED ON CABLE TYPE
112
TERM
TERMINATION DESCRIPTION
DD50S
FIFTY PIN CONNECTOR, FEMALE, SOLDER TERMINATIONS,
COMMERCIAL "D" SUBMINIATURE. THIS CONNECTOR
CONSISTS OF THE FOLLOWING PARTS:
CONNECTOR - ITT CANNON P/N DD50S
SHELL - ITT CANNON P/N DD24661
SCREW LOCK - ITT CANNON P/N D20420
DIN3
THREE PIN CONNECTOR, SPECIAL APPLICATION FOR PRESSURE
TRANSDUCER AND SOLENOID VALVE, DIN 43650/ISO 4400.
OMEGA P/N CX5302.
DIN6P
SIX PIN CONNECTOR, MALE, DIN PLUG. SPECIAL APPLICATION FOR
LAKESHORE TEMPERATURE CONTROLLER MODEL 340.
SUPPLIER: LAKESHORE, 575 MCCORKLE BLVD, WESTERVILLE, OH 43082,
(614)891-2244. P/N: 106-233
DIN96P
NINETY-SIX PIN CONNECTOR, MALE, 3X32 DIN CONNECTOR,
HARTING ELECTRONICS BRAND. P/N#09-03-096-3214
SHELL HOUSING: 09-03-96-0501.
CABLE INSERTS:
09-02-000-9911.
LOCKING LEVERS: 09-02-000-9902 (L), 09-02-000-9903 (R)
DISHI
THIS IS A BURNDY MINILOCK PIN THAT IS NO LONGER AVAILABLE.
IT IS NOT RECOMMENDED TO MAKE ANY TERMINATIONS TO THE AREA
CALLED "DISHI" AS IT IS VERY UNRELIABLE.
D37FLT
THIRTY SEVEN PIN CONNECTOR, D-SUBMINIATURE FOR FLAT
CABLE. AMPHENOL CAT. #841-17DCFR-B37P.
D37P
THIRTY SEVEN PIN CONNECTOR, MALE, "D" AMP
#17-20370-1 ASSEMBLE WITH CABLE HOUSING (BACK SHELL)
17-313-01, AND SPRING LATCH PLATE 17-259. USE CRIMP PIN
17-766-02, AND INSTALL USING CRIMP TOOL 357-100 WITH PIN
LOCATOR BUSHING 357-300-2.
D37S
THIRTY SEVEN PIN CONNECTOR, FEMALE, "D" AMP
#17-10370-1 ASSEMBLE WITH CABLE HOUSING (BACK SHELL)
17-313-01, AND SPRING LATCH PLATE 17-529. USE CRIMP PIN
17-763-02, AND INSTALL USING CRIMP TOOL 357-100 WITH PIN
LOCATOR BUSHING 357-300-2.
D50FLT
FIFTY PIN CONNECTOR, D-SUBMINIATURE FOR FLAT CABLE.
SLAC S/N59-299-165-50.
8/8/2011
APPLICATION
USED ON CABLE TYPE
VSAM
SLC SLITS
12C16/3V
113
TERM
TERMINATION DESCRIPTION
D50F
A THREE PART CONNECTOR CONSISTING OF: CONNECTOR
RECEPTACLE, JUNCTION SHELL AND SCREW LOCK ASSEMBLY.
THESE ARE LBL STOCK ITEMS. THE RESPECTIVE PART NAMES
AND STOCK NUMBERS ARE:
CONNECTOR - AMPHENOL PN #17-10500-1 LBL #5935-34166
SHELL - ITT CANNON PN #DD24661 LBL #5935-57869
SCREW LOCK - ITT CANNON PN #D20419-12 LBL #5935-67234
12C16/3V
F59B
COAXIAL CONNECTOR, TYPE F CABLE PLUG, NEWARK P/N 32N1129,
TYPE CP5F9-1/8. NOTE THAT THE COAX SOLID CENTER
CONDUCTOR IS THE MALE PIN. USE KINGS CRIMPING TOOL KTH1000 WITH DIE KTH-2002 AND TRIM CODE 401.
RG59
F59QS
COAXIAL CONNECTOR, TYPE "F" CABLE PLUG, SIGNAL
VISION.CAT. #QF59-RNS-QD. NOTE THAT THE COAXIAL SOLID
CENTER. CONDUCTOR IS THE MALE PIN. USE THE FOLLOWING
TOOLS TO ASSEMBLE CONNECTOR:
1. STRIPPING TOOL SIGNAL VISION CAT. #QF-ST
2. QF COMPRESSION TOOL SIGNAL VISION CAT. #QF-CT
3. INSERTION TOOL RILEY CO. CAT. #ITF-59,6,11
FIOP-ST
FIBER OPTIC CONNECTOR. TYPE 'ST' LIGHTGUIDE
CONNECTOR, CERAMIC TIP, BAYONET-TYPE TWIST LOCK MFG
AT&T. P/N P2020C-C-125, COMCODE 105 143 911.
FIXED
THE CABLE IS FIXED TO, AND AN INTEGRAL PART OF A UNIT OR
DEVICE. THE CABLE IS NOT INTENDED TO BE FIELD REPAIRED
OR REPLACED.
FLAG-1
TERMINAL, SLAC MANUFACTURED, 6061 ALUMINUM, 1 HOLE
CABLE FLAG WATER COOLED.
FLAG-2
TERMINAL, SLAC MANUFACTURED, 6061 ALUMINUM, 2 HOLE
CABLE FLAG WATER COOLED. 1"WCAL
F1/2RP
COAXIAL CONNECTOR, "F" FEMALE, FOR SEMI-RIGID
JT-4500 SERIES COAXIAL CABLE. GILBERT PART NO.
GRS-500-BAFF-DU-03. SEE THE GILBERT CATALOG
FOR TRIM AND ASSEMBLY INSTRUCTIONS.
8/8/2011
APPLICATION
SLCNET AND
FFNET TAPS
USED ON CABLE TYPE
RG59QS
FIOPMM12, 24, 48, 52
SLC FF TRIPLET
TEMP.MON.SYS.
RG59
1”WCAL
1/2" RD, 3PR24IS
114
TERM
TERMINATION DESCRIPTION
FO-SPL
FIBER OPTIC ROTARY MECHANICAL SPLICE. THIS SPLICING
REQUIRES A 1040AB TOOL KIT, A D181617 CONSUMABLES KIT,
AT-8995 INDEX MATCHING GEL AND REAGENT GRADE ALCOHOL.
THE SPLICE IS STORED IN A UC-SS/M1 ORGANIZER AND IN A
MECHANICAL TRAY. TERMINATION IS TO BE PERFORMED BY
TRAINED AND AUTHORIZED PERSONNEL ONLY.
FUSION
FUSION SPLICING OF FIBER OPTIC CABLE ENDS. SPLICES WILL
BE CONTAINED IN A HEAT SHRINK SLEEVE WITH A SMALL METAL
ROD FOR STRENGTH. SPLICES MAY BE FURTHER PLACED IN TRAY
FOR ADDITIONAL PROTECTION AND FIBER MANAGEMENT.
GH-4M
FOUR PIN CONNECTOR, MALE. THIS CONNECTOR IS SUPPLIED
WITH THE COLD CATHODE MODULE FROM MKS INSTRUMENTS INC.
GP-20S
TWENTY PIN CONNECTOR, FEMALE. THIS CONNECTOR IS SUPPLIED
BY GRANVILLE-PHILLIPS WHEN A MODEL 350 ION GAUGE
CONTROLLER IS ORDERED.
GP-CON
USE CED-30 CONNECTOR. WIRE AS SHOWN BELOW, USING
THE INDICATED CABLE COLOR-CODE FOR SEQUENCE. NINE PINS
ARE CONNECTED AS INDICATED. OTHER PINS AND/OR WIRES ARE
NOT CONNECTED.
CED-30
PIN # PAIR # WIRE #
01
05
07
08
09
10
11
13
14
9C18J
GP-GAU
SPECIAL PREWIRED 6-PIN (IG-CP6) AND BNC CONNECTORS
FOR CONNECTION OF AN ION-GAUGE TO A GRANVILLE-PHILLIPS
SERIES 270 ION-GAUGE CONTROLLER.
IG-CABLE
HALPRB1
CONNECTOR, 40 PIN, MPT-132-30S (01391083),
GROUP 3 TECH., AUCKLAND, NEW ZEALAND.
HALPRB2
CONNECTOR, 40 PIN, MPT-132-30S (01391084),
GROUP 3 TECH., AUCKLAND, NEW ZEALAND.
8/8/2011
APPLICATION
USED ON CABLE TYPE
FIOPMM12, FIOPMM24,
FIOPMM48, FIOPMM52
VACG
115
TERM
TERMINATION DESCRIPTION
HALPRB3
CONNECTOR, 40 PIN, MPT-132-15M (01391054),
GROUP 3 TECH., AUCKLAND, NEW ZEALAND.
HN213
COAXIAL CONNECTOR, TYPE HN CABLE PLUG, KINGS CAT.
#KH-59-19, 50 OHM, SLAC P/N59-299-020-54.,5KV,
HV RATING. USE CRIMPING TOOL KTH-1000 WITH
DIE KTH-2003 AND TRIM CODE 402.
RG213R
HN214
COAXIAL CONNECTOR, TYPE HN CABLE PLUG, KINGS CAT-#
KH-59-21, SLAC P/N59-299-020-55, 5KV, HV RATING.
USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH 2004
AND TRIM CODE 402M.
RG214
HN214M
COAXIAL CONNECTOR, TYPE HN CABLE PLUG. KINGS CAT. NO.
KN-59-21, MODIFIED TO SPECIFICATIONS AS SHOWN ON DRAWING
# CA-344-296-00. CONNECTOR TERMINATES A TMS8481 COAXIAL
CABLE. USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2004
SEE DRAWING # CA-344-296-00 FOR CABLE TRIM CODE.
INJ. KICKER
MODULATOR
HPJ
SIX PIN CONNECTOR, FEMALE, HP SPECIAL. PRE-WIRED ONTO
ONE END OFAN HP POWER METER CABLE.
RF POWER METER
HP-CORD
HPP
SIX PIN CONNECTOR, MALE, HP SPECIAL. PRE-WIRED ONTO
ONE END OF AN HP POWER METER CABLE.
RF POWER METER
HP-CORD
HR13P
THIRTEEN PIN MALE RECEPTACLE, HIGH RADIATION,
CERAMIC INSULATED, BEAM SWITCHYARD REMOTE OPERABLE
DISCONNECT, SLAC BUILT. REFERENCE SLAC 887-006
DRAWING PACKAGE AND WD-233-702-00.
ARC PPS
(STOPPERS)
HR13S
THIRTEEN PIN FEMALE RECEPTACLE, HIGH RADIATION,
CERAMIC INSULATED, BEAM SWITCHYARD REMOTE OPERABLE
DISCONNECT, SLAC BUILT. REFERENCE SLAC 887-006
DRAWING PACKAGE AND WD-233-702-00.
ARC PPS
(STOPPERS)
4PR16TC
HRS4
FOUR PIN CONNECTOR, FEMALE, PLASTIC, SUB-MINIATURE,
MFR HRS (JAPAN) P/N DF13-45-1.25C.
HV-C
COAXIAL CONNECTOR, 10KV HV CABLE PLUG. REYNOLDS CAT.
NO. 167-3554.
ION CHAMBERS
SSRL ION PUMPS
TYPE-C
HV-CBJ
COAXIAL CONNECTOR, 10KV BULKHEAD JACK,
KINGS CAT.#1062-2.USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-2001 AND TRIM CODE 484.
8/8/2011
APPLICATION
USED ON CABLE TYPE
116
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
HVW213
COAXIAL CONNECTOR, 10KV CABLE PLUG. W.W. FISCHER
CAT. #S105A108/10.7
VACP SYS
RG213R
HVWTIME
COAXIAL CONNECTOR, 10KV CABLE PLUG. W.W. FISCHER
CAT.#S105A108/5.2.
VACP SYS
TIMES, TYPE-C
RG58R
HV58
COAXIAL CONNECTOR, 10KV HV CABLE PLUG,
KINGS CAT. #1065-2, SLAC S/N59-299-034-01.
USE CRIMPING TOOL KTH-1000 WITH DIE
KTH2001 AND TRIM CODE 419.
RG58R, TYPE-C
HV58J
COAXIAL CONNECTOR, 10KV HV CABLE JACK,
KINGS CAT. #1062-2, USE KINGS CRIMPING
TOOL KTH-1000 WITH DIE KTH-2001 AND
TRIM CODE 419 AND HEAT GUN.
TYPE-C
HV213
COAXIAL CONNECTOR, 20KV HV CABLE PLUG. KINGS CAT.
NO. 1765-1 OR REYNOLDS CAT. NO. 167-3516, S/N.
59-299-033-01. USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-1078 OR -2078 AND TRIM
CODE 475 OR DIE KTH-2003 AND TRIM
CODE REY2, RESPECTIVELY.
ION PUMP POWER
SUPPLY END
RG213R
HV214
USE HV213 CONNECTOR, WITH A LARGER FERRULE (SLEEVE)
FOR RG214, KINGS P/N #S89-24-2, SLAC S/N59-299-009-06.
INSTALL A 6" PIECE OF RED SHRINK TUBING AT EACH
END OF CABLE 3" FROM THE CONNECTOR. USE CRIMPING
TOOL KTH-1000 WITH DIE KTH-1079 AND TRIM CODE 475.
PLIC
SYSTEM
RG214
HV220
SPECIAL SLAC HV CONNECTOR AND CONNECTIONS. SEE CABLE
INSTALLATION GROUP OR SLAC ELECTRONICS GROUP FOR
DETAILS. HV CONNECTOR, ISOLATION DESIGN INC. MODEL
D-103-SL.
KLYSTRON HV
RG220, HVSPEC1
IG20
TWENTY PIN CONNECTOR, FEMALE, POSITRONIC IND. P/N
GM20FSCDOJUL-734.0. THIS CONNECTOR IS SUPPLIED BY
THE MFR. WHEN ORDERING A GRANVILLE-PHILLIPS
IONIZATION GAUGE CONTROLLER MODEL 330
8/8/2011
117
TERM
TERMINATION DESCRIPTION
APPLICATION
IG21
FOUR PIN CONNECTOR, FEMALE PINS, CANNON CAT. NO.
SK-U4-21C-1/2. ION GAUGE WIRE AS FOLLOWS:
BLK #14 AWG UNSHIELDED WIRE TO PIN #1
RED #14 AWG UNSHIELDED WIRE TO PIN #2
BLK #16 AWG SHIELDED WIRE TO PIN #3
CLEAR #16 AWG SHIELDED WIRE TO PIN #4(COAX CENTER PIN)
THE TWO SHIELDS ARE TO BE CONNECTED TOGETHER AND TO THE
PIN #4 COAXIAL SLEEVE. THE SHIELDS MUST NOT TOUCH THE
CONNECTOR SHELL.THE COAXIAL PIN IS PART OF A SPECIAL
ELECTROMETER CIRCUIT, AND MUST BE KEPT
EXTREMELY CLEAN REFER TO DWG. CA-208-102-01-R0
ION-GAU
ARC BOX
IG22
FOUR PIN CONNECTOR, MALE PINS, CANNON CAT. NO.
RSK-U4-22C-1/2. WIRE ION THE SAME AS IG21.
ION GAUGE
I&C RACKS
ION-GAU
IG23
A "Y" CABLE ASSEMBLY TERMINATING IN TWO CONNECTORS
WITH 12" LEAD LENGTHS. THE MULTI-CONDUCTOR CABLE
IS A BURNDY TT12S AND THE COAX A BNC58.
USE SHRINK-TUBE AT BASE OF "Y".SEE CONNECTORS FOR
PART NUMBERS.
SSRL
ION GAUGES
ION-GAU3
IG24
A "Y" CABLE ASSEMBLY TERMINATING IN TWO CONNECTORS
WITH 12" LEAD LENGTHS. THE MULTI-CONDUCTOR CABLE
IS A BURNDY TT12P AND THE COAX A BNC58.
USE SHRINK-TUBE AT BASE OF "Y".
SEE CONNECTORS FOR PART NUMBERS.
SSRL
ION GAUGES
ION-GAU3
IG-CP6
SIX PIN MALE CABLE PLUG, AMPHENOL CAT-# 86-CP6.
IG-RS4
FOUR PIN FEMALE RECEPTACLE, CHASSIS MOUNT, AMPHENOL
CAT. #78-RS4 2
VACG (HOT FIL)
ION-GAU2
IPA
AMPHENOL HV CONNECTOR, 97-5106A-18-420S.
PRE-WIRED ONTO ONE END OF THE VARIAN HV CABLE
FOR ION PUMPS.
KLY ION PUMP
VARIAN
IPL1
COAXIAL CABLE TERMINATION FOR H.V. BOX. SEE DWG.
AD-208-911-00-RO FOR DETAILS.
DISTRIBUTED
ION PUMP
JUNCTION BOX
RG213R
8/8/2011
USED ON CABLE TYPE
IG-CABLE
118
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
IPL2
COAXIAL CABLE TERMINATION FOR H.V. BOX.
SEE DWG. IC7, DETAIL 7. 1 RING LUG,
AMP NO. 33457 OR EQ. (SLAC S/N59-294-744-51),
1 RING LUG, AMP NO. 31902 OR EQ.
(SLAC S/N59-294-711-41),
AND 1 BUTT CONNECTOR, AMP 320562 OR
EQ. (SLAC S/N59-294-770-07).
HOLDING ION PUMP
JUNCTION BOX
RG213R
IPL3
VARIAN PREFABRICATED ARMORED CABLE TERMINATION
FOR H.V. BOX. SEE DWG IC7, DETAIL 6,
AND INSTALL RING LUG WITHOUT SHORTENING
INSULATED INNER WIRE.
HOLDING ION PUMP
JUNCTION BOX
VARIAN A
IPVA
VARIAN SHIELDED "BANANA PLUG" CONNECTOR FOR
VAC ION PUMPS, PRE-WIRED ONTO ONE END OF
THE VARIAN HV CABLE FOR ION PUMPS.
HOLDING ION PUMP
VARIAN,VARIAN A
IPVA25
VARIAN HV ION PUMP CONNECTOR,
MODEL 03642700A FOR VAC ION PUMP #25
CONNECTOR MUST BE ASSEMBLED ONTO HV COAX.
VARIAN HOLDING
ION PUMP #25
TIMES
IPVB
DUNAWAY STOCK ROOM CORP. TYPE C-100 CONNECTOR FOR
VARIAN HOLDING ION PUMPS.
VARIAN HOLDING
ION PUMP
RG213
IPVC
ION-PUMP CONNECTOR, DESY-TYPE.(XXKV RATED)
MODEL #SR03648982 VARIAN INC. (EXCLUSIVE US.
DISTRIBUTION)STRAIN RELIEF (FOR TYPE-C & RG58R).
195 O.D.REF: CABLE STRAIN RELIEF
SSRL DWG # PF-441-167-40 C0
IPVR
HIGH-VOLTAGE FEED-THRU, DESY-TYPE (XXKV RATED)
DESY FEED-THRU ON MINI-CON FLAT MODEL #SR0364720
IPS100X
VARIAN HV ION PUMP CONNECTOR, FOR VAC ION PUMP
# S100X CONNECTOR MUST BE ASSEMBLED ONTO HV COAX.
DUNIWAY,PART # S-100-X.
HV ION PUMP
TIMES, TYPE-C
JAE3P
THREE PIN CONNECTOR, MALE PLUG, MFR JAEGER,
DESIGNATOR #FMR G1024, REFERENCE # 532653.
CONNECTOR IS SUPPLIED BY THE ORSAY FACILITY.
JAE3S
THREE PIN CONNECTOR, FEMALE PLUG, MFR JAEGER,
DESIGNATOR #FFR J0086, REFERENCE # 532003.
CONNECTOR IS SUPPLIED BY THE ORSAY FACILITY.
8/8/2011
119
TERM
TERMINATION DESCRIPTION
JAE4P
FOUR PIN CONNECTOR, MALE PLUG, MFR JAEGER,
DESIGNATOR #FMR G1003, REFERENCE # 532654.
CONNECTOR IS SUPPLIED BY THE ORSAY FACILITY.
JAE12P
TWELVE PIN CONNECTOR, MALE PLUG, MFR JAEGER,
DESIGNATOR #E6 FMR, REFERENCE # 532662.
CONNECTOR IS SUPPLIED BY THE ORSAY FACILITY.
KST6
CABLE PLUG, SINGLE CONDUCTOR, GERMAN MANUFACTURER,
CONTACT P/N 15-0002-COLOR USED FOR FAST SHUDDER PULSE
CURRENT.
#6
LB01-4
LUG, CRIMP, 1/4" BOLT-HOLE FOR #1/0 AWG WIRE, COPPER
LONG BARREL, UNINSULATED, SQUARE-D CAT. #VHCL-1/0-14. USE
SLAC APPROVED CRIMP TOOLING ONLY.
#1/0
LB01-5
LUG, CRIMP, 5/16-INCH BOLT-HOLE FOR COPPER #1/0 AWG WIRE,
WIRE,LONG BARREL, UNINSULATED, SQUARE-D P/N #VHCL 1/0-516.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#1/0
LB01-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE FOR COPPER #1/0 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N #VHCL 1/0-38.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#1/0
LB01-6S
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED, STANDARD BARREL.
FOR COPPER #1/0 AWG WIRE OR #1/0 FLEX CABLE. USE MFG T&B
P/N 54109 OR EQUIVALENT. USE SLAC APPROVED CRIMP TOOLING ONLY.
1/0TLSNH
LB01-6SR
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED, STANDARD BARREL,
RIGHT ANGLE.FOR COPPER #1/0 AWG WIRE OR #1/0 FLEX CABLE.
USE MFG T&B P/N 54109UB OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
1/0TLSNH
LB01-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE FOR COPPER #1/0 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N #VHCL 1/0-12.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#1/0
LB01-8F
LUG, CRIMP, 1/2-INCH BOLT-HOLE FOR COPPER #1/0 AWG
FLEX CABLE,LONG BARREL.MFG:T&B, P/N:54950BE OR
EQUIVALENT.USE SLAC APPROVED CRIMP TOOLING ONLY.
1/0TLSNH
LB019-6
LUG,CRIMP, 3/8 INCH BOLT HOLE, UNINSULATED,
LONG BARREL FOR AL/CU 1/0 CABLE. THOMAS AND BETTS
P/N 60130. USE SLAC APPROVED CRIMP TOOLING ONLY.
#1WELD, #1/0
8/8/2011
APPLICATION
USED ON CABLE TYPE
120
TERM
TERMINATION DESCRIPTION
LB01D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4 CENTERS.
FOR COPPER #1/0 AWG WIRE, LONG BARREL, UNINSULATED, AMP
CAT. #53680-2 USE SLAC-APPROVED CRIMP TOOLING ONLY.
#1/0
LB02-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE FOR COPPER #2/0 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N #VHCL 2/0-38.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#2/0
LB02-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE FOR COPPER #2/0 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N #VHCL 2/0-12.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#2/0
LB02D6
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 3/8 DIA ON 1" CENTERS.
LONG BARREL, UNINSULATED, FOR COPPER #2/0 AWG WIRE.
SQUARE D P/N #VHCL-2/0-38B.
#2/0
LB02D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4 CENTERS,
FOR COPPER #2/0 AWG WIRE, LONG BARREL, UNINSULATED,
SQUARE-D P/N VHCL- 2/0-12BN USE SLAC APPROVED CRIMP
TOOLING ONLY.
#2/0
LB03-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE, FOR COPPER #3/0 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D
P/N VHCL-3/0-38.USE SLAC APPROVED CRIMP TOOLING ONLY.
#3/0
LB03-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, FOR COPPER #3/0 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-3/0-12. USE
SLAC APPROVED CRIMP TOOLING ONLY.
#3/0
LB039-6
LUG,CRIMP, 90 DEGREE, 3/8 INCH BOLT HOLE, UNINSULATED,
LONG BARREL FOR AL/CU 3/0 CABLE. THOMAS AND BETTS
P/N 60142UB. USE SLAC APPROVED CRIMP TOOLING ONLY.
2/0WELD, #3/0
LB049-3
CONNECTOR TERMINAL YELLOW 90 DEGREE STANDARD BARREL
#4/0 AWG. 1 HOLE LUG 3/8 INCH BOLT SIZE. ALPHA EQUIPMENT
COMPANY. PART# 58163UB. MANUFACTURER: THOMAS & BETTS.
4/0FLX, 4/0TLSNH
LB03D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4
CENTERS, FOR COPPER #3/0 AWG WIRE, LONG BARREL,
UNINSULATED, SQUARE-D P/N VHCL- 3/0-12BN.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#3/0
LB04-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE, FOR COPPER #4/0 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-4/0-38.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#4/0
8/8/2011
APPLICATION
USED ON CABLE TYPE
121
TERM
TERMINATION DESCRIPTION
LB04-6FL
LUG, CRIMP, 3/8-INCH BOLT-HOLE,UNINSULATED,LONG BARREL.
FOR COPPER #4/0 AWG FLEX CABLE.USE MFG T&B P/N:54913BE06
OR EQUIVALENT.USE SLAC APPROVED CRIMP TOOLING ONLY.
4/0TLSNH
LB04-6S
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED, STANDARD BARREL.
FOR COPPER #4/0 AWG FLEX CABLE. USE MFG T&B P/N 54174 OR
EQUIVALENT. USE SLAC APPROVED CRIMP TOOLING ONLY.
4/0TLSNH
LB04-6SR
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED,
STANDARD BARREL,RIGHT ANGLE. FOR COPPER #4/0 AWG FLEX CABLE.
USE MFG T&B P/N 54174UB OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
4/0TLSNH
LB04-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE FOR COPPER #4/0 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-4/0-12.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#4/0
LB04D6
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 3/8 DIA ON 1" CENTERS.
FOR COPPER #4/0 AWG WIRE, LONG BARREL, UNINSULATED,
SQUARE D P/N VHCL-4/0-38B. USE SLAC APPROVED CRIMP TOOLING
ONLY.
#4/0
LB04D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4 CENTERS,
FOR COPPER #4/0 AWG WIRE, LONG BARREL, UNINSULATED,
SQUARE-D P/N VHCL-4/0-12BN. USE SLAC APPROVED CRIMP
TOOLING ONLY.
#4/0
LB04D8F
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4 CENTERS,
LONG BARREL. FOR COPPER #4/0 AWG FLEX CABLE.
MFG:T&B, P.N: 54868BE. USE SLAC APPROVED CRIMP
TOOLING ONLY.
4/0TLSNH
LB1-4
LUG, CRIMP, 1/4-INCH BOLT HOLE, STANDARD BARREL. FOR COPPER
#1 AWG WIRE. MFG: T&B, P/N:54108 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY
LB1-5
LUG, CRIMP, 5/16-INCH BOLT-HOLE, FOR COPPER #1 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-1-516.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#1
LB1-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, FOR COPPER #1 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D VHCL-1-38.
USE SLAC APPROVED CRIMPING TOOL ONLY.
#1
8/8/2011
APPLICATION
USED ON CABLE TYPE
122
TERM
TERMINATION DESCRIPTION
LB1-8
LUG, CRIMP, 1/2-INCH BOLT HOLE, FOR COPPER #1 AWG
WIRE, STANDARD BARREL, UNINSULATED, MFG: THOMAS & BETTS,
COLOR-KEYED,P/N:54150.
USE SLAC APPROVED CRIMPING TOOL ONLY.
#1
LB1D6
LUG, CRIMP, DOUBLE BOLT HOLE, 2X3/8 DIAMETER ON 1.00"
CENTERS, FOR COPPER #1 AWG WIRE, LONG BARREL,
UNINSULATED, BURNDY P/N YA1C-2TC38. USE SLAC APPROVED
CRIMP TOOLING ONLY.
#1
LB1D8
LUG, CRIMP, DOUBLE BOLT HOLE, 2X1/2 DIAMETER ON 1.75"
CENTERS, FOR COPPER #1 AWG WIRE, LONG BARREL
UNINSULATED, BURNDY P/N YA1C-2N. USE SLAC APPROVED CRIMP
TOOLING ONLY.
#1
LB2SS
LUG, ONE BOLT HOLE, SET SCREW TYPE, FOR #2 TO #4AWG
2/0, 4/0
LB2-4
LUG, CRIMP, 1/4-INCH BOLT-HOLE, FOR COPPER #2 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-2-14.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#2
LB2-5
LUG, CRIMP, 5/16-INCH BOLT-HOLES FOR COPPER #2 AWG,
WIRE, LONG BARREL, UNINSULATED. MFG:T&B, P/N:54942BE
OR EQUIVALENT. (SQUARE-D P/N VHCL-2-516- OBSOLETE).
USE SLAC APPROVED CRIMP TOOLING ONLY.
#2
LB2-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE, FOR COPPER #2 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-2-38.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#2
LB2-6S
COPPER ONE-HOLE LUG – STRAIGHT STANDARD BARREL
MAX 35KV, #2 AWG WIRE, 3/8” BOLT MTG SIZE, TIN PLATED
WITH INSPECTION HOLE, T&B CATALOG NUMBER: 54143-TB.
2C2TLSNH
LB2D6
COPPER TWO-HOLE LUG – STRAIGHT LONG BARREL MAX 35KV,
#2 AWG WIRE, 3/8” BOLT MTG SIZE, 1 3/4” HOLE SPACING,
TIN PLATED BLIND END, BROWN 33 T&B CATALOG NUMBER: 54810BE.
2C2TLSNH
LB2D8
DESCRIPTION: COPPER TWO-HOLE LUG - STRAIGHT LONG BARREL
MAX 35KV, #2 AWG WIRE, 1/2" BOLT MTG SIZE, 1 3/4" HOLE SPACING,
TIN PLATED BLIND END, BROWN 33 T&B CATALOG NUMBER:54811BE
2C2TLSNH
2C2LSNH
LB25FX6
LUG, CRIMP, 3/8-INCH BOLT HOLE, UNINSULATED, STANDARD BARREL,
FOR COPPER 262 FLEX DLO CABLE.
MFG: BURNDY. P/N:YA31LTC38FX.
262FLX
8/8/2011
APPLICATION
USED ON CABLE TYPE
123
TERM
TERMINATION DESCRIPTION
LB3/0
LUG, 3/8-INCH COPPER ONE-HOLE FOR #3/0 AWG or 2/0 FLEX WIRE.
STRAIGHT STANDARD BARREL – MAX 35KV. TIN PLATED WITH
INSPECTION HOLE. ORANGE 50. THOMAS&BETTS CATALOG #54111.
2/0TLSNH
LB3D8
LUG, CRIMP, DOUBLE BOLT HOLE, 2 X 1/2IN DIAMETER ON 1-3/4"
CENTERS, LONG BARREL, UNINSULATED, FOR COPPER 3/0 AWG WIRE,
THOMAS&BETTS P/N 54864BE.
2/0TLSNH, 3/0AWG
LB4/0
LUG, CRIMP, 3/8 DIAMETER, STANDARD BARREL, UNINSULATED,
FOR COPPER 4/0 AWG FLEX WIRE, THOMAS&BETTS P/N 58163.
4/0TLSNH
LB4-3
LUG, 1/4-INCH, COPPER ONE-HOLE, FOR #4 AWG WIRE.
STRAIGHT HOLE. GRAY 29. THOMAS&BETTS CATALOG #54106.
#4,2C4TLN,2C4TLNU
LB4-4
LUG, CRIMP, 1/4-INCH BOLT HOLE, FOR COPPER #2 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-2-14.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#4
LB4-5
LUG, CRIMP, 5/16-INCH BOLT HOLE, FOR COPPER #4 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-4-516.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#4
LB4-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, FOR COPPER #4 AWG
WIRE, LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-4-38.
SLAC S/N59-294-747-81.USE SLAC APPROVED CRIMP TOOLING ONLY.
#4
LB4D8
LUG, CRIMP, DOUBLE BOLT HOLE, 2X1/2 DIAMETER ON 1-3/4"
CENTERS, LONG BARREL, UNINSULATED. FOR COPPER #4 AWG
WIRE. MFG: FCI/BURNDY P/N: #YA4C-2N.
MFG: T&B, P/N: 256-30695-733 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
#4
LB4-SS
LUG, ONE BOLT HOLE, SET SCREW TYPE, FOR #4 TO #8 AWG.
#4-#8
LB6-3
LUG, CRIMP, #10 BOLT HOLE, FOR COPPER #6 AWG WIRE, LONG
BARREL, UNINSULATED, SQUARE-D P/N VHCL-6-10/8. SLAC
S/N59-294-748-01. USE SLAC APPROVED CRIMP TOOLING ONLY.
#6
LB6-4
LUG, CRIMP, 1/4 INCH BOLT HOLE, FOR COPPER #6 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-6-14. SLAC
S/N59-294-748-02. USE SLAC APPROVED CRIMP TOOLING ONLY.
#6
LB6-5
LUG, CRIMP, 5/16-INCH BOLT HOLE, FOR COPPER #6 AWG WIRE,
LONG BARREL, UNINSULATED, SQUARE-D P/N VHCL-6-516. USE
SLAC APPROVED CRIMP TOOLING ONLY.
#6
8/8/2011
APPLICATION
USED ON CABLE TYPE
124
TERM
TERMINATION DESCRIPTION
LB6-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, FOR #6 AWG WIRE, SHORT
BARREL, UNINSULATED, AMP CAT. #328144. SLAC
S/N59-294-748-04. USE SLAC APPROVED CRIMP TOOLING ONLY.
LB6-7
LUG, CRIMP, 1/4-INCH BOLT HOLE, FOR #6 AWG WIRE, SHORT
BARREL, UNINSULATED, GRAINGER #3LL41. DIE CODE 24.
USE SLAC APPROVED CRIMP TOOLING ONLY.
LB6D8
LUG, CRIMP, DOUBLE BOLT HOLE, 2X1/2 DIAMETER ON 1-3/4"
CENTERS, LONG BARREL, UNINSULATED, FOR COPPER #6 AWG
WIRE, BURNDY CAT. #YA6C-2N.
#6
LB8/0
LUG, 5/16-INCH, COPPER ONE-HOLE, FOR #8 AWG WIRE. STRAIGHT
STANDARD BARREL – MAX 35KV, TIN PLATED WITH INSPECTION
HOLE. RED 21. THOMAS&BETTS CATALOG #54131.
2C8TLN
LB8-3
LUG, CRIMP, #10 BOLT HOLE, FOR COPPER #8 AWG WIRE, LONG
BARREL, UNINSULATED, BURNDY CAT. #YA8C-TC10.
SLAC S/N59-294-745-51. USE SLAC APPROVED CRIMP TOOLING ONLY.
#8
LB8-4
LUG,
LONG
MFG:
SLAC
#8
LB8-5
COPPER ONE-HOLE,LUG – STRAIGHT STANDARD BARREL – MAX 35KV,
#8 AWG WIRE, #10 BOLT SIZE, T&B CATALOG NUMBER: 54104
USE SLAC APPROVED CRIMP TOOLING ONLY.
LB8-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, FOR COPPER #8 AWG WIRE,
SHORT BARREL, UNINSULATED, BURNDY CAT. #YA8C-L3-BOX. USE
SLAC APPROVED CRIMP TOOLING ONLY.
#8
LB8-8
LUG, CRIMP, 1/2-INCH BOLT HOLE, FOR COPPER #8 AWG WIRE,
SHORT BARREL, UNINSULATED, BRUNDY CAT. #YA8C-L4-BOX. USE
SLAC APPROVED CRIMP TOOLING ONLY
#8
LB8-SS
LUG, ONE BOLT HOLE, SET SCREW TYPE, FOR #14 TO #8 AWG.
#14-#8
LB25-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, UNINSULATED, LONG BARREL,
FOR COPPER 250MCM CABLE, SQUARE-D P/N VHCL-250-38. USE
SLAC APPROVED CRIMP TOOLING ONLY.
250MCM
8/8/2011
CRIMP, 1/4-INCH BOLT HOLE, FOR COPPER #8 AWG WIRE,
BARREL, UNINSULATED, MFG: FCI/BURNDY P/N: #YA8C-TC14.
T&B, P/N: 54930BE OR EQUIVALENT.
S/N59-294-745-41. USE SLAC APPROVED CRIMP TOOLING ONLY.
APPLICATION
USED ON CABLE TYPE
#6
125
TERM
TERMINATION DESCRIPTION
LB25-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED,
LONG BARREL, FOR COPPER 250MCM CABLE.
SQUARE-D P/N VHCL-350-12. USE SLAC APPROVED
CRIMP TOOLING ONLY.
250MCM
LB25D8
LUG, CRIMP, DOUBLE BOLT HOLE, 2 X 1/2IN DIAMETER ON 1-3/4"
CENTERS, LONG BARREL, UNINSULATED, FOR COPPER 250MCM WIRE,
THOMAS&BETTS P/N 54868BE
4/0TLSNH,250MCM
LB30-6
LUG, CRIMP, 3/8-INCH BOLT HOLE, UNINSULATED,
LONG BARREL, FOR AL/CU 300MCM CABLE, THOMAS
AND BETTS P/N 60160. USE SLAC APPROVED CRIMP
TOOLING ONLY.
300MCM
LB30D6
LUG, CRIMP, DOUBLE BOLT HOLE, 2X 3/8" DIA
ON 1-3/4 CENTERS. UNINSULATED, LONG BARREL,
FOR 300MCM COPPER CABLE, SQUARE-D P/N VHCL-300-38BN.
USE SLAC APPROVED CRIMP TOOLING ONLY.
300MCM
LB30D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA
ON 1-3/4 CENTERS. UNINSULATED, LONG BARREL,
FOR 300 MCM COPPER CABLE. SQUARE-D
P/N VHCL-300-12BN. USE SLAC APPROVED CRIMP
TOOLING ONLY.
300MCM
LB35-5FS
LUG, CRIMP, 5/16-INCH BOLT – SINGLE HOLE,UNINSULATED,
SHORT BARREL. FOR COPPER 350 MCM FLEX CABLE.
PANDUIT CAT.#LCAX350-56-6 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
LB35-6FL
LUG, CRIMP, 3/8-INCH BOLT - SINGLE HOLE, UNINSULATED,
LONG BARREL. FOR COPPER 350 MCM FLEX CABLE. T&B
CAT.# 54916BE06 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
350TLSNH
LB35-6FS
LUG, CRIMP, 3/8-INCH BOLT - SINGLE HOLE, UNINSULATED,
SHORT BARREL. FOR COPPER 350 MCM FLEX CABLE.
T&B CAT.# 5411606 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
350TLSNH
LB35-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED,
LONG BARREL, FOR COPPER 350 MCM CABLE. SQUARE-D
P/N VHCL-350-12. USE SLAC APPROVED CRIMP TOOLING ONLY.
350MCM
8/8/2011
APPLICATION
USED ON CABLE TYPE
126
TERM
TERMINATION DESCRIPTION
LB35-9
LUG, CRIMP, 3/8-INCH BOLT - SINGLE HOLE, UNINSULATED,
SHORT BARREL, FOR COPPER 350 MCM FLEX CABLE. T&B
CAT. # 256-30695-112 USE SLAC APPROVED CRIMP TOOLING ONLY.
350TLSNH
LB35-10
LUG, CRIMP, 3/8-INCH BOLT - DOUBLE HOLE, 2 X 3/8" DIA
ON 1" CENTERS, UNINSULATED, LONG BARREL, FOR COPPER
350MCM FLEX CABLE (ALSO GOOD FOR 313 FLEX AND 400MCM CODE)
USE T&B TOOL TBM8-750M-1 WITH BLUE DIE CODE # 76 OR SLAC
APPROVED CRIMP TOOLING ONLY. T&B CAT. # 54821BE313BS.
350TLSNH
LB35D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON
1-3/4 CENTERS. UNINSULATED, LONG BARREL, FOR 350 MCM
COPPER CABLE. SQUARE-D P/N VHCL-350-12BN.
USE SLAC APPROVED CRIMP TOOLING ONLY.
350MCM
LB35D8F
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON
1-3/4 CENTERS, LONG BARREL. FOR COPPER 350 MCM
FLEX CABLE. MFG: T&B, P/N:54874BE OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
350TLSNH
LB35D8FS
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2" DIA ON 1-3/4" CENTERS,
UNINSULATED, STANDARD BARREL. FOR 350 MCM FLEXIBLE COPPER
CABLE T&B CAT. # 58277 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
350TLSNH
LB35D9
LUG,CRIMP,DOUBLE BOLT-HOLE, 2 X 1/2" DIA ON 1-3/4"
CENTERS.UNINSULATED, LONG BARREL, FOR 350 MCM FLEXIBLE
COPPER CABLE(ALSO GOOD FOR 313 MCM FLEX AND 400MCM CODE)
T&B CAT. #5487BE313BS. USE T&B TOOL TBM8-750M-1 WITH BLUE
DIE CODE # 76 OR SLAC APPROVED C CRIMP TOOLING ONLY.
LB50-6
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED, STANDARD BARREL,
FOR COPPER 500MCM CABLE. USE SLAC APPROVED CRIMP TOOLING ONLY.
MFG: THOMAS & BETTS. P/N 256-30695-339
500MCM
LB50-6F
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED, STANDARD BARREL.
FOR COPPER 500MCM FLEX CABLE. USE MFG T&B P/N 5412006 OR
EQUIVALENT. USE SLAC APPROVED CRIMP TOOLING ONLY.
500TLSNH
LB50-6FL
LUG, CRIMP, 3/8-INCH BOLT-HOLE, UNINSULATED,
LONG BARREL. FOR COPPER 500MCM FLEX CABLE. USE MFG
T&B P/N 54921BE06 OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
500TLSNH
8/8/2011
APPLICATION
USED ON CABLE TYPE
127
TERM
TERMINATION DESCRIPTION
LB50-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED,
SHORT BARREL,FOR COPPER 500-600 MCM CABLE.
SQUARE-D P/N VHCL-500-12.
USE SLAC APPROVED CRIMP TOOLING ONLY.
LB50D6
LUG, CRIMP, 2 BOLT HOLES, 3/8" DIAMETER ON 1"
CENTERS, LONG BARREL, UNINSULATED, FOR 450
TO 550 MCM CABLE. AMP CAT. #326808.
USE SLAC APPROVED CRIMP TOOLING ONLY.
LB50D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA
ON 1-3/4 CENTERS, LONG BARREL, UNINSULATED,
FOR COPPER 450-550 MCM CABLE. AMP CAT.#53642-2.
USE SLAC-APPROVED CRIMP TOOLING ONLY.
500MCM
LB50D8F
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA
ON 1-3/4 CENTERS, LONG BARREL, FOR COPPER
500 MCM FLEX CABLE. MFG: T&B, P/N:54878BE OR
EQUIVALENT.USE SLAC-APPROVED CRIMP TOOLING ONLY.
500TLSNH
LB50D8FS
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA ON 1-3/4 CENTERS,
STANDARD BARREL. FOR COPPER MCM FLEX CABLE, USE MFG: T&B,
P/N: 54289BE OR EQUIVALENT.
USE SLAC APPROVED CRIMP TOOLING ONLY.
500TLSNH
LB53D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA
ON 1-3/4 CENTERS, LONG BARREL, UNINSULATED,
FOR COPPER 535KCMIL CABLE.SQUARE-D
P/N VHCL-535-12. USE SLAC-APPROVED CRIMP TOOLING ONLY.
535MCM
LB60-5
LUG, CRIMP, 5/8-INCH BOLT-HOLE, UNINSULATED, STANDARD
BARREL,600MCM FOR COPPER 600 MCM CABLE , 5002AND 500MCM
FLEX CABLE.T&B PART 500TLSNH NUMBER 54120, TIN PLATED
BLIND END, GREEN 94 OR SLAC APPROVED CRIMP TOOLING ONLY.
600MCM,500TLSNH
2C500TLS
LB60-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED, LONG BARREL,
FOR COPPER 600 MCM CABLE AND 500MCM FLEX CABLE. T&B PART
NUMBER 54921BE, TIN PLATED BLIND END, GREEN 94
600MCM, 500TLSNH
LB60D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA.
ON 1-3/4 CENTERS. UNINSULATED, LONG BARREL
FOR 600 MCM COPPER CABLE. SQUARE-D P/N VHCL-600-12BN.
USE SLAC-APPROVED CRIMP TOOLING ONLY.
600MCM
8/8/2011
APPLICATION
USED ON CABLE TYPE
500MCM
128
TERM
TERMINATION DESCRIPTION
LB60S8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED, SHORT BARREL,
FOR COPPER 600 MCM COPPER CABLE, AND 500MCM FLEX CABLE.
T&B PART NUMBER 256-30695-1370
600MCM, 500TLSNH
LB75-8
LUG, CRIMP, 1/2-INCH BOLT-HOLE, UNINSULATED,
LONG BARREL,FOR COPPER 750 MCM CABLE.
BURNDY CAT. #YA39-N. USE SLAC APPROVED CRIMP TOOLING ONLY.
750MCM
LB75D8
LUG, CRIMP, DOUBLE BOLT-HOLE, 2 X 1/2 DIA
ON 1-3/4 CENTERS. UNINSULATED, LONG BARREL,
FOR 750MCM COPPER CABLE. SQUARE-D VHCL-750-12BN.
USE SLAC-APPROVED CRIMP TOOLING ONLY.
750MCM
LB309-6
LUG,CRIMP, 90 DEGREE, 3/8 INCH BOLT HOLE,
UNINSULATED,LONG BARREL FOR AL/CU 300MCM CABLE.
THOMAS AND BETTS P/N 60160UB. USE SLAC APPROVED
CRIMP TOOLING ONLY.
250WELD,300MCM
LBR02-6
LUG, CRIMP, RIGHT ANGLE, 3/8-INCH BOLT-HOLE FOR COPPER
#2/0 AWG AND #1/0 AWG FLEX WIRE. STANDARD BARREL,
UNINSULATED,THOMAS&BETTS P/N 54110UB. USE SLAC APPROVED
CRIMP TOOLING ONLY.
#1/0FLEX, #2/0
LC
CONNECTOR IS FACTORY TERMINATED WITH A LC/UPC CONNECTOR
AND A 1 m PIGTAIL WHICH IS UNTERMINATED. THE PIGTAILS ARE
SINGLE MODE FIBER AND COLOR CODED TO STANDARD EIA/TIA COLOR
SCHEMA. WHEN USED WITH THE COMMSCOPE SYSTIMAX G2 SHELF
SYSTEM THE LC PIGTAILS ARE PART OF A 12 CONNECTOR MODULE:
SYSTIMAX P/N MODG2-12LC-SM.
LC-DUP
FIBER OPTIC CONNECTOR, DUPLEX, 2 FIBER CABLE, 900ΜM
TIGHT-BUFFERED CABLE RECOMMENDED 62.5/125ΜM OM1,
50/125ΜM OM2, 10GIG™ 50/125ΜM LASER OPTIMIZED OM3
AND 9/125ΜM OS1, 1.6MM – 2.0MM JACKETED CABLE, PANDUIT
P/N FLCDMEI (MULTIMODE WITH 1.6MM – 2.0MM JACKETED CABLE),
P/N FLCDM900EI (900ΜM BUFFERED FIBER), P/N FLCDSBU
(SINGLEMODE WITH 1.6MM – 2.0MM JACKETED CABLE), P/N
FLCDS900BU(SINGLEMODE WITH 900ΜM BUFFERED FIBER).
LC-SIM
FIBER OPTIC CONNECTOR, SIMPLEX SINGLE FIBER CONNECTOR,
900ΜM TIGHT-BUFFERED CABLE RECOMMENDED 62.5/125ΜM OM1,
50/125ΜM OM2, 10GIG™ 50/125ΜM LASER OPTIMIZED OM3 AND
9/125ΜM OS1, 1.6MM 2.0MM JACKETED CABLE PANDUIT P/N
FLCSMEI(MULTIMODE), P/N FLCSSBU (SINGLEMODE WITH 900ΜM
BUFFERED FIBER AND 1.6MM – 2.0MM JACKETED CABLE)
8/8/2011
APPLICATION
USED ON CABLE TYPE
FOMMDP62
129
TERM
TERMINATION DESCRIPTION
LEMO
CONNECTOR, COAXIAL PLUG, KINGS CAT.#1075-1,
SLAC S/N59-299-052-01. USE CRIMP DIE KTH-2082.
LEMO-A
USE LEMO2P CONNECTOR.
WIRE #1 WIRE (CLEAR) TO THE SOCKET-PIN (PIN-2).
WIRE #2 WIRE (BLACK) TO THE PLUG-PIN (PIN-1).
WIRE SHIELD TO CONNECTOR SHELL.
APPLICATION
USED ON CABLE TYPE
RG174, RG188
2C22MS
LEMOHV1
CONNECTOR, COAXIAL PLUG, HIGH VOLTAGE (HV), CABLE SIZE O.D.
2.2MM - 2.6MM (0.09IN - 0.1IN), 7500 VAC/10500 VDC, 8 AMP
AC/DC, 250 DEG C. LEMO P/N:FFB.1S.405.CTAC27.
RG58TLN
LEMOHV2
CONNECTOR, COAXIAL PLUG, HIGH VOLTAGE (HV), CABLE SIZE O.D.
4.3MM - 5.1MM (0.17IN - 0.2IN), 7500 VAC/10500 VDC, 8 AMP
AC/DC, 250 DEG C.LEMO P/N:FFB.1S.405.CLAC52.
TYPE-C
LEMO2P
CONNECTOR, LEMO TYPE, KINGS, K-LOC, 2 CONTACT
CABLE PLUG, SOLDER CUPS, KINGS #1885-1,
SLAC S/N59-299-053-52.
2C22MS, RG108A
LEMO3P
THREE PIN CONNECTOR, PLUG, 3 CONTACTS (2 PINS AND 1 SOCKET),
HALF MOON INSERT ARRANGEMENT, SOLDER CUP, CABLE O.D.
RANGE: 4.8-5.6MM MFG: LEMO, P/N:FFA.1S.303.CLAC57
LEMO4P
CONNECTOR, LEMO TYPE, KINGS, K-LOC, 4 CONTACT
CABLE PLUG, SOLDER CUPS, KINGS #1905-1,
SLAC S/N59-299-053-54.
LEMO5P
FIVE PIN CONNECTOR, MALE PLUG. POWER PLUG FOR ROPER
SCIENTIFIC CAMERA MODEL: CASCADE 512B. MFG: LEMO.
LEMO6P
CONNECTOR, LEMO TYPE, 6 CONTACT CABLE PLUG,
SOLDER CUPS, P/N FFA.1S.306.CLAD.62 PIN ALIGNED
LEMO6PK
CONNECTOR, LEMO TYPE, 6 CONTACT CABLE PLUG,
SOLDER CUPS, KEYWAY ALIGNED, P/N FGG.1B.306.CLAD.72Z.
USE BEND RELIEF BOOT P/N GMA.1B.065.D (BLACK BOOT).
LEMO8PK
CONNECTOR, LEMO TYPE, 8 CONTACT CABLE PLUG,
SOLDER CUPS, P/N FGG.2B.308.CLAD.99Z KEYWAY ALIGNED.
LEMO58
CONNECTOR, COAXIAL PLUG, KING K-LOC, KING CAT #1075-2.
8/8/2011
1PR20OS
130
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
LFB
LUG, "FASTON", BLUE PREINSULATED CRIMP
RECEPTACLE FOR #14 TO, #16 AWG WIRE,
AMP CAT. #42332-2. SLAC S/N59-294-751-02,
USE HAND CRIMPING TOOL AMP #59250.
CROSS-CONNECT
TERMINAL BLOCKS
TRUNKS
(nn)C16 SERIES,
3PR22OS, 4PR18TC,
24PR16TC, 50PR16TC,
3C16TYR, 5PR20OS,
1PR16T3V, 4PR16AS,
5C16,6V, 8PR16OS,
6C18TC,12C18OS,
18PR22OS,50C16T3V,
2C16T3V
LFR
LUG, "FASTON", FEMALE, RED PREINSULATED CRIMP
RECEPTACLE FOR #18 TO #22 AWG WIRE, AMP
CAT. NO.42599-2. SLAC S/N59-294-751-01.
USE HAND CRIMPING TOOL AMP #59250 ONLY.
FLOW & LIMIT
SWITCHES
12C22T6V, 15PR22OS,
26C22/3V, 1PR22OS,
27PR22OS, 2C22MS,
3PR22OS, 2C16OS,
5PR20OS, 6PR22OS,
19C16T6V, 11PR22OS,
5C16T6V, 8C18OS,
19C18T3V, 9C18J,
18PR22OS, 2C18TC,
5C18TC, 6C18TC,
7C18TC, 12C18TC,
19PR22IS, 12C20J
4C20OS, 12PR22IS,
4PR18TC, 4C20OS,
LF-RA
LUG FASTON, RIGHT ANGLE, SPECIAL ASSEMBLY, FLAG
TERMINALS. MFG. ELPRESS P/N'S B2507 FLPB8 AND B1003
FLSV5. ASSEMBLED WITH ISOLATORER.
LFY
LUG, "FASTON", YELLOW PREINSULATED RECEPTACLE
FOR #12 TO #10 AWG WIRE, AMP CAT. NO. 42844-1. SLAC
S/N59-294-751-03. USE HAND CRIMPING TOOL 90246-1 ONLY.
AC LINE
3C12TYR, 2C12TYR
5C12TYR
LOPWR21
PLUG CONNECTOR, FEMALE, COAX STYLE, LOW DC POWER. 2.1MM ID,
5.5MM OD. SUPPLIER: DIGIKEY. MFG: CUI. P/N: PP3-002A.
LRB1/4
LUG, RING, BLUE, CRIMP, STUD SIZE 1/4", FOR #14 TO
#16 AWG WIRE. AMP CAT. #31906 OR EQUIVALENT, SLAC
S/N59-294-711-61. USE HAND CRIMPING TOOL 90009-8.
LRB3/8
LUG, RING, BLUE, CRIMP, STUD SIZE 3/8" FOR #14 TO #16
AWG WIRE, SLAC S/N59-294-711-81. USE HAND CRIMPING
TOOL AMP#59250.
8/8/2011
1PR16OS
131
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
LRB#6
LUG, RING, BLUE, CRIMP, STUD SIZE #6, FOR #14 TO #16 AWG
WIRE. AMP NO. 31901 OR EQUIVALENT, SLAC
S/N59-294-711-31. USE HAND CRIMPING TOOL AMP #59250.
WIRE IN COLOR CODE SEQUENCE. SEE THE WIRE TYPE FOR THE
COLOR CODE.
BACKLEGS
2C14TYR, 1PR16OS
8C16/3V, 8PR16TS
4PR16OS
LRB#8
LUG, RING, BLUE, CRIMP, STUD SIZE #8, FOR #14 TO #16
AWG WIRE.AMP 31902 OR EQUIVALENT, SLAC S/N59-294-711-41.
USE HAND CRIMPING TOOL AMP #59250.
2C16/3V
LRB#10
LUG, RING, BLUE, CRIMP, STUD SIZE #10, FOR #14 TO #16
AWG WIRE. AMP 31903 OR EQUIVALENT, SLAC S/N59-294-711-51.
USE HAND CRIMPING TOOL AMP #59250.
4PR16AS
LRR1/4
LUG, RING, RED, CRIMP, STUD SIZE 1/4", FOR #18 TO
#22 AWG WIRE. AMP 31894 OR EQUIVALENT, SLAC
S/N 59-294-710-61.USE HAND CRIMPING TOOL AMP #59250.
1PR20OS, 12PR22IS
12C22/3V
LRR#6
LUG, RING, RED, CRIMP, STUD SIZE #6, FOR #18 TO #22 AWG
WIRE. AMP 8-36152-1 OR EQUIVALENT, SLAC S/N59-294-710-31.
USE HAND CRIMPING TOOL AMP #59250.
1PR20OS
LRR#8
LUG, RING, RED, CRIMP, STUD SIZE #8, FOR #18 TO #22 AWG
WIRE. AMP 31890 OR EQUIVALENT. SLAC P/N59-294-710-41. USE
HAND CRIMPING TOOL AMP #59250.
LRY6R
LUG, RING, YELLOW, CRIMP, STUD SIZE #6, FOR #10 TO #12 AWG
WIRE. RADIATION RESISTANT INSULATION (PVF2), BURNDY CAT.
#YAES10K-11. USE HAND CRIMP TOOL AMP #59239-4.
LRY#6
LUG, RING, YELLOW, CRIMP, STUD SIZE #6, FOR #10 TO #12 AWG
WIRE. AMP NO. 35149 OR EQUIVALENT, LBL #5940-3194, SLAC
S/N59-294-713-31.USE HAND CRIMPING TOOL AMP #59239-4.
WIRE IN COLOR CODE SEQUENCE. SEE THE WIRE TYPE FOR THE
COLOR CODE.
LRY#6-1
LUG, RING, YELLOW, CRIMP, STUD SIZE #6, FOR #16 TO #14
AWG WIRE. AMP NO. 35634 OR EQUIVALENT, SLAC
S/N59-294-712-31.USE HAND CRIMPING TOOL AMP #59239-4.
LRY-7
LUG RING TONGUE, YELLOW, INSULATED, CRIMP, STUD SIZE #6,
FOR #10 OR #12 AWG WIRE. COPPER LUG WITH 0.145 DIA HOLE.
AMP CAT# 320634, USE HAND CRIMPING TOOL AMP #59239-4.
8/8/2011
2C12TYR, 2C10TC
4C12T6V, 4C1076V
AC POWER
3C12TYR, 2C12OS
8C12T6V
132
TERM
TERMINATION DESCRIPTION
LRY#8
LUG, RING, YELLOW, CRIMP, STUD SIZE #8, FOR #10
TO #12 AWG WIRE. AMP 35108 OR EQUIVALENT,
SLAC59-294-713-41. USE HAND CRIMPING TOOL AMP #59239-4.
5C12TYR, 2C12TYR
LRY#8-1
LUG, RING, YELLOW, CRIMP, STUD SIZE #8, FOR #16
TO #14 AWG WIRE. AMP 35106 OR EQUIVALENT,
SLAC59-294-712-41. USE HAND CRIMPING TOOL AMP #59239-4.
8C12T6V
LRY#10
LUG, RING, YELLOW, CRIMP, STUD SIZE #10, FOR #10
TO #12 AWG WIRE. AMP 35109 OR EQUIVALENT, SLAC
S/N59-294-713-51. USE HAND CRIMPING TOOL AMP #59239-4.
3C12TYR, 4C12TYR
LRY#10-1
LUG, RING, YELLOW, CRIMP, STUD SIZE #10, FOR #16 TO #14
AWG WIRE. AMP 34805 OR EQUIVALENT, SLAC S/N59-294-712-51.
USE HAND CRIMPING TOOL AMP #59239-4.
8C12T6V
LRY1/4
LUG, RING, YELLOW, CRIMP, FOR 1/4" STUD SIZE, FOR
#10 TO #12 AWG WIRE. SLAC S/N59-294-713-61.
USE HAND CRIMP TOOL AMP #59239-4.
#12
LRY-5
LUG RING, YELLOW, INSULATED, CRIMP, STUD SIZE 5/16",
FOR #10 OR #12 AWG WIRE. AMP CAT. #35111, SLAC
59-294-713-71.USE HAND CRIMPING TOOL AMP #59239-4.
#12
LRY-6
LUG RING, YELLOW, INSULATED, CRIMP, STUD SIZE 3/8",
FOR #10 OR #12 AWG WIRE. AMP CAT# 35112,
SLAC S/N59-294-713-81. USE HAND CRIMPING TOOL
AMP #59239-4.
#12
LRY-8
LUG RING, YELLOW, INSULATED, CRIMP, STUD SIZE 1/2",
FOR #10 OR #12 AWG WIRE. AMP CAT# 35151,
SLAC S/N59-294-713-91. USE HAND CRIMPING TOOL
AMP #59239-4.
#12
LR2-5
LUG, RING, UNINSULATED, CRIMP, STUD SIZE 5/16", FOR #2
AWG WIRE, AMP CAT. #322870 OR EQUIVALENT. USE SLAC
APPROVED CRIMPING TOOL ONLY.
#2
LR2-6
LUG, RING, UNINSULATED, CRIMP, STUD SIZE 3/8", FOR
#2 AWG WIRE, AMP CAT. #321600. USE SLAC
APPROVED CRIMPING TOOL ONLY.
#2
LR2-8
LUG, RING, UNINSULATED, CRIMP, STUD SIZE 1/2", FOR
#2 AWG WIRE, AMP #321602 OR EQUIVALENT. USE SLAC APPROVED
CRIMPING TOOL ONLY.
#2
8/8/2011
APPLICATION
USED ON CABLE TYPE
133
TERM
TERMINATION DESCRIPTION
LR4#10
LUG, RING, INSULATED, CRIMP, STUD SIZE #10, FOR #4
AWG WIRE,AMP CAT. #322052. USE SLAC APPROVED
CRIMPING TOOL ONLY.
LR6#10
LUG, RING, UNINSULATED, CRIMP, STUD SIZE #10,
FOR #6 AWG WIRE.AMP CAT. #33464. USE SLAC APPROVED
CRIMPING TOOL ONLY.
FF KICKER
#6,HVSPEC1
LR6#10S
LUG,RING,UNINSULATED,CRIMP,FOR #6AWG,STUD SIZE
#10,19 STRAND WIRE, AMP 321298, USED SLAC APPROVED
CRIMPING TOOL ONLY.
TRIM WINDING
2C6T6VOS
LR8-4
LUG, RING,INSULATED, CRIMP, STUD SIZE 1/4", FOR #8
AWG WIRE, AMP CAT. #33461, SLAC S/N59-294-745-41.
USE SLAC APPROVED CRIMPING TOOL ONLY.
LR8-6
LUG, RING, INSULATED, STUD SIZE 3/8 INCH, FOR #8
AWG WIRE,AMP CAT. #322004. USE SLAC APPROVED CRIMPING
TOOL ONLY.
FF
2C8TYR
LR8#10
LUG, RING, INSULATED, CRIMP, STUD SIZE #10, FOR #8 AWG
WIRE, AMP CAT. #322154,SLAC S/N59-294-745-51. USE SLAC
APPROVED CRIMPING TOOL ONLY.
LR8U10
LUG, RING, UNINSULATED, CRIMP, STUD SIZE #10, FOR #8 AWG
WIRE. AMP. CAT #31807, SLAC S/N 59-294-745-51. USE SLAC
APPROVED CRIMPING TOOL ONLY.
LSB#6
LUG, SPADE, BLUE, CRIMP, STUD SIZE #6, FOR #14 TO #16 AWG
WIRE. AMP #320861 OR EQUIVALENT, LBL #5940-31964, SLAC
S/N59-294-733-31. USE HAND CRIMPING TOOL AMP #59250.
3C16TYR, 1PR16AS,
4PR16AS, 1PR16T3V,
2C16/3V, 5C16/6V,
9C18J
LSB#8
LUG, SPADE, BLUE, CRIMP, STUD SIZE #8, FOR #14 TO #16 AWG
WIRE. AMP NO. 320862 OR EQUIVALENT, LBL #5940-31989, SLAC
S/N59-294-733-41. USE HAND CRIMPING TOOL AMP #59250.
2C16OS, 3C16/3V
LSB#10
LUG, SPADE, BLUE, CRIMP, STUD SIZE #10, FOR #14 TO #16
AWG WIRE. AMP NO.320863 OR EQUIVALENT, SLAC
S/N59-294-733-51. USE HAND CRIMPING TOOL AMP #59250.
LSR#6
LUG, SPADE, RED, CRIMP, STUD SIZE #6, FOR #18 TO
#22 AWG WIRE. AMP NO. 32562 OR EQUIVALENT, LBL
#5940-31951, SLAC S/N59-294-732-31. USE HAND
CRIMPING TOOL AMP #59250.
8/8/2011
APPLICATION
USED ON CABLE TYPE
#4
4C8TYR,4C8SHLD
FOCUS MAG
#8
2C22MS, 12C18OS,
2C18TC, 6C18TC,
8C18OS
134
TERM
TERMINATION DESCRIPTION
LSR#8
LUG, SPADE, RED, CRIMP, STUD SIZE #8, FOR #18 TO
#22 AWG WIRE. AMP NO.32498 OR EQUIVALENT,
SLAC S/N59-294-732-41. USE HAND CRIMPING TOOL
AMP #59250.
LSR#10
LUG, SPADE, RED, CRIMP, STUD SIZE #10, FOR #18 TO
#22 AWG WIRE. AMP NO.32054 OR EQUIVALENT, SLAC
S/N59-294-722-51. USE HAND CRIMPING TOOL AMP #59250.
LSY#8
LUG, SPADE, YELLOW, CRIMP, STUD SIZE #8, FOR #10
TO #12 AWG WIRE.AMP 32510 OR EQUIVALENT.
SLAC S/N59-294-735-41.USE HAND CRIMPING TOOL 59239-4 ONLY.
LSY#10
LUG, SPADE, YELLOW, CRIMP, STUD SIZE #10, FOR
#10 TO #12 AWG WIRE. AMP NO. 32589 OR EQUIVALENT,
USE HAND CRIMPING TOOL 90246-1 ONLY.
MCX
BANANA TYPE PLUG WITH WHITE COLORED PLASTIC
INSULATING SHELL FURNISHED WITH THE KAPTON CABLE TYPE.
KAPTON
MG8P
EIGHT PIN CONNECTOR, MALE, CABLE PLUG,
MFR. MELLES GRIAT P/N 06DDA002.
4PR22IS
MG8S
EIGHT PIN CONNECTOR, FEMALE, CABLE PLUG,
MFR. MELLES GRIAT P/N 06DDA001.
4PR22IS
MLP
CONNECTOR, MALE, CABLE PLUG, 90 AMP, MULTILAM HUGIN
INDUSTRIES P/N 09043.
#4AWG
MLS
CONNECTOR, FEMALE, CABLE SOCKET, 90 AMP, MULTILAM
HUGIN INDUSTRIES P/N 10751.
#4AWG
MLX3S
CONNECTOR, 3 PIN, FEMALE, SOLDER CONNECTIONS. MOLEX P/N
09-50-3061.
MLX4P
FOUR PIN CONNECTOR, MOLEX CAT. #39-01-2045, WITH
CONTACT POINT AND STRAIN RELIEF, MOLEX CAT.#39-00-0220
AND 15-04-0296 RESP.
MLX4S
FOUR PIN CONNECTOR, FEMALE RECEPTACLE, MOLEX CAT.
#39-01-2040, STRAIN RELIEF, MOLEX CAT. #15-04-0294
AND GOLD PLATED TERMINALS, MOLEX CAT. #39-00-164.
USE HAND CRIMPING TOOL, MOLEX CAT. #11-01-0197.
8/8/2011
APPLICATION
USED ON CABLE TYPE
2C12TYR, 2C10TYR,
HVSPEC2
1PR18OS
135
TERM
TERMINATION DESCRIPTION
MLX4X
FOUR PIN CABLE CONNECTOR, MOLEX CAT#39-01-3049,
WITH CONTACT POINT AND STRAIN RELIEF,
MOLEX CAT.#39-00-0182 AND 15-04-0296 RESP.
THIS SHALL BE USED TO DISCONNECT THE CABLE WHEN THE
RAFT IS MOVED AWAY FROM THE DETECTOR.
MLX6S
SIX PIN CONNECTOR, FEMALE RECEPTACLE, MOLEX CAT.
#39-01-2060, STRAIN RELIEF, MOLEX CAT. #15-04-0296
AND GOLD PLATED TERMINALS, MOLEX CAT. #39-00-164.
USE HAND CRIMPING TOOL, MOLEX CAT. #11-01-0197.
MLX6S1
SIX PIN CABLE CONNECTOR, MOLEX CAT. #39-01-2065, WITH
CONTACT POINT AND STRAIN RELIEF, MOLEX CAT. #39-00-0220
AND 15-04-0296 RESP.
MLX12P
TWELVE PIN CABLE CONNECTOR, MOLEX CAT. #39-01-2125,
WITH CONTACT POINT AND STRAIN RELIEF, MOLEX CAT.
#39-00-0220 AND 15-04-0345 RESP.
MLX12S
TWELVE PIN CONNECTOR, FEMALE RECEPTACLE, MOLEX
CAT. #39-01-2120, STRAIN RELIEF, MOLEX CAT. #15-04-0345
AND GOLD PLATED TERMINALS, MOLEX CAT. #39-00-164.
USE HAND CRIMPING TOOL, MOLEX CAT. #11-01-0197
AND #39-01-2125.
MLX12X
TWELVE PIN CABLE CONNECTOR, MOLEX CAT. #39-01-3129,
WITH CONTACT POINT AND STRAIN RELIEF, MOLEX CAT.#39-00-0182
AND 15-04-0345 RESP. THIS SHALL BE USED TO DISCONNECT THE
CABLE WHEN THE RAFT IS MOVED AWAY FROM THE DETECTOR.
MS-HVS
SINGLE CONTACT, THREADED CONNECTOR, AMPHENOL
NO. MS-3106A-18-420S, RATED AT 9 KV RMS/20 A MAX.
TERMINATION IS TO BE DONE PER DRAWING SA-125-089-01,
'ION PUMP HV CABLE CONNECTOR ASSEMBLY'.
RG213R
MS2S
TWO PIN CONNECTOR, FEMALE STRAIGHT PLUG,ITT
CANNON P/N MS3106A-12S-3S. SOLDER PINS
1PR22OS
MS3P
THREE PIN CONNECTOR, MALE, MS-3126F-12-3P, SLAC
S/N 59-299-210-52. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-7 AND STOP SL-2 ONLY.
TUNE MEAS
2C22MS, 2C16OS
MS3S
THREE PIN CONNECTOR, FEMALE, MS-3126F-12-3S,
SLAC S/N59-299-210-02. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
TUNE MEAS
2C22MS, 3C20/3V
1PR22OS
8/8/2011
APPLICATION
USED ON CABLE TYPE
2PR18OS
4PR18OS, 1PR18OS
136
TERM
TERMINATION DESCRIPTION
MS3S-A
THREE PIN CONNECTOR, FEMALE, MS3106A-10SL-3S,
STRAIGHT PLUG, SOLDER CONNECTIONS, MFR IS AMPHANOL.
NOT A SLAC STORES ITEM.
MS3S-S
THREE PIN CONNECTOR, FEMALE, MS-3106B-14S-7S,
STRAIGHT PLUG, SPLIT SHELL, SOLDER CONNECTIONS,
MFR. AMPHENOL. NOT SLAC STORES ITEM.
MS4P
FOUR PIN CONNECTOR, MALE, BENDIX P/N PTO6A-8-4P.
MS4S
FOUR PIN CONNECTOR, FEMALE, BENDIX P/N PTO6A-8-4S.
MS4SA
APPLICATION
USED ON CABLE TYPE
8PR22OS
LINAC VAC
1PR22OS
FOUR PIN CONNECTOR, FEMALE, MS-3116F-8-4S.
SLMO
1PR22OS
MS5P
FIVE PIN CONNECTOR, MALE, MS3126F-14-50, SLAC
P/N 59-299-210-54. USE HAND CRIMPING TOOL
MS10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
FF KICKER
6C16OS
MS5S
FIVE PIN CONNECTOR, FEMALE, MS-3126F-14-5S, SLAC
S/N59-299-210-04. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
KLY AMP
FF KICKER
3C16/3V, HVSPEC2
6C16OS
MS5SR
FIVE PIN CONNECTOR, FEMALE RECEPTACLE,
MS-3120E-14-5S. USE HAND CRIMPING TOOL MS10S-1
WITH DIE S-7 AND STOP SL-2 ONLY.
SLAC S/N59-299-410-54.
MS5S-S
FIVE PIN CONNECTOR, MS3106A-18-11S, STRAIGHT PLUG,
FEMALE, SOLDER CONNECTIONS, MFR-AMPHENOL.
NOT A SLAC STORES ITEM.
MS6P
SIX PIN CONNECTOR, MALE, MS-3126F-10-6P,
SLAC P/N59-299-210-51. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-6A AND STOP SL-3A ONLY.
MS6PR
SIX PIN MALE CHASSIS MOUNT CONNECTOR, MS-3120-10-6P,
SLAC P/N59-299-410-01. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-6A AND STOP SL-3A ONLY.
MS6PRC
SIX PIN CONNECTOR, MALE, CABLE END RECEPTACLE,
MS-3121F-10-6P. USE HAND CRIMPING TOOL M10S-1 WITH
DIE S-6A AND STOP SL-3A ONLY.
8/8/2011
2PR22OS
KLY/KICKER
#10AWG
137
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
MS6PSB
SIX PIN CONNECTOR, MALE, MS-3126F-10-6P, S/N
59-299-210-51. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-6A AND STOP SL-3A ONLY. WIRE PER
DRAWING CA-123-854-00:
PAIR 1, BLACK/RED,
RED TO PIN-A
W/DRAIN
BLACK TO PIN-B
PAIR 2, BLACK/GREEN,
GREEN TO PIN-C
W/DRAIN
BLACK TO PIN-D
DRAIN WIRES, PAIRS 1 & 2, CONNECT BOTH TO PIN-E
NO CONNECTION TO PIN-F.
PAIR 3, BLACK/WHITE,
NO CONNECTIONS,
CUT BACK TO EDGE OF JACKET.
CAMAC SERIAL
BRANCH CABLE
3PR24IS
MS6S
SIX PIN CONNECTOR, FEMALE, MS-3126F-10-6S. SLAC
S/N 59-299-210-01. USE HAND CRIMPING TOOL MS10S-1
WITH DIE S-6A AND SL-3A.
DC XFMR
3PR20IS, 2PR24IS
3PR18OS
MS6SR
SIX PIN FEMALE CHASSIS MOUNT CONNECTOR,
MS-3120-10-6S,SLAC S/N59-299-410-51. USE
HAND CRIMP TOOL MS10S-1 WITH DIE
S-6A AND STOP SL-3A ONLY.
MS7P
SEVEN PIN CONNECTOR, MALE, MS-3106A-16S-1P,
AMPHENOL, SOLDER CONNECTIONS.
MS7S
SEVEN PIN CONNECTOR, FEMALE, MS-3106A-16S-1S,
AMPHENOL, SOLDER CONNECTIONS.
MS8P
EIGHT PIN CONNECTOR, MALE, MS-3126F-16-8P, SLAC
S/N 59-299-210-58. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-7 AND STOP SL-2 ONLY.
CONTROL, SSI
8C16/3V, 6PR22OS,
8C18OS, 5C18TC
MS8PA
EIGHT PIN CONNECTOR, MALE, MS-3106E-22-23P, SOLDER
CONNECTIONS.
MS8PAR
EIGHT PIN CONNECTOR, MALE, MS-3102E-22-23P, MALE
RECEPTACLE, SOLDER CONNECTIONS.
MS8PW
EIGHT PIN CONNECTOR, MALE, MS-3106F-22-23PW, SOLDER
CONNECTIONS.
8C12T6V, 9C12T6V,
4C12T6V, 4C10T6V
MS8PY
EIGHT PIN CONNECTOR, MALE, MS-3106F-22-23PY, SOLDER
CONNECTIONS.
8C12T6V, 9C12T6V,
4C12T6V, 4C10T7V
8/8/2011
8C12T6V, 9C12T6V
4C12T6V, 4C10T6V
FF BARREL
QUAD TRIMS
8C12T6V, 2C12TYR
138
TERM
TERMINATION DESCRIPTION
MS8RPA
EIGHT PIN CONNECTOR, MALE RECEPTACLE. MS-3101E-22-23P.
AMPHENOL, SOLDER CONNECTIONS.
MS8S
EIGHT PIN CONNECTOR, FEMALE, MS-3126F-16-8S, SLAC
S/N 59-299-210-08. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-7 AND STOP SL-2 ONLY.
MS8SA
EIGHT PIN CONNECTOR, MS-3106E-22-23S, SOLDER
CONNECTIONS.
8C12T6V,9C12T6V,
4C12T6V,4C10T6V
MS8SB
EIGHT PIN CONNECTOR, FEMALE, MS3116F-14-5S.
NOT A STORES ITEM.
9C18OS
MS10P
TEN PIN CONNECTOR, MALE, MS-3126F-12-10P, SLAC
S/N59-299-210-53. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-6A AND STOP SL-3A ONLY.
3PR22OS,2C16OS,
10S22OS,20C20OS,
10C18OS,2C20OS,
10C16T3V
MS10PA
TEN PIN CONNECTOR, MALE, MS-3106A-18-19P, AMPHENOL,
SOLDER CONNECTIONS.
4C20OS
MS10PR
TEN PIN CONNECTOR, MALE CHASSIS RECEPTACLE,
MS3120F-12-10P, SLAC S/N59-299-410-03. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-6A AND STOP SL-3P ONLY.
MS10PRA
TEN PIN CONNECTOR, MALE RIGHT ANGLE PLUG, MS-3108R-18-IP.
ITT INDUSTRIES. SOLDER CONNECTION.
USED WITH BELDEN #83709 9C#16 CABLE AND
BELDEN #83715 15C#16 CABLE.
MS10S
TEN PIN CONNECTOR, FEMALE, MS-3126F-12-10S, SLAC
S/N59-299-210-03. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-6A AND STOP SL-3A ONLY.
MS10SB
TEN PIN CONNECTOR, FEMALE, MS3106A-18-19S,
AMPHENOL, SOLDER CONNECTIONS.
MS10SR
TEN PIN CONNECTOR, FEMALE RECEPTACLE,
MS3120-12-10S, SLAC S/N59-299-410-53. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-6A AND STOP SL-3A.
MS10SRA
TEN PIN CONNECTOR, FEMALE RIGHT ANGLE PLUG,
MS-3108R-18-IS.ITT INDUSTRIES. SOLDER CONNECTION.
USED WITH BELDEN #83709 9C#16 CABLE AND
BELDEN #83715 15C#16 CABLE.
8/8/2011
APPLICATION
USED ON CABLE TYPE
2C12RR
KLY, SSI
RF CAVITY
TUNER
3C16/3V,5PR20OS,
12C16/3V,
3PR22OS,8C16/3V
3PR22OS, 2C16OS,
2C20OS, 10C18OS
4PR22IS, 1PR22OS
139
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
MS11P
ELEVEN PIN CONNECTOR, MS-3126F-18-11P,
SLAC S/N59-299-210-60. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
SSI
12C16T6V
MS11PR
ELEVEN PIN CONNECTOR, MS-3120E-18-11P, MALE
RECEPTACLE, SLAC S/N59-299-410-10. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
FF BARREL
KLIXONS
1PR16TS, 2C16/3V
MS11PRA
ELEVEN PIN CONNECTOR, MALE RIGHT ANGLE PLUG,
MS-3108E-24-20P. AMPHENOL. SOLDER CONNECTION.
USED WITH BELDEN #83709 9C#16 CABLE AND
BELDEN #83715 15C#16 CABLE.
MS11S
ELEVEN PIN CONNECTOR, MS-3126F-18-11S,
SLAC S/N59-299-210-10. USE HAND CRIMPING
TOOL M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
SSI, KICKER
5PR20OS, 12C16/3V,
5C16/6V
MS11SRA
ELEVEN PIN CONNECTOR, FEMALE RIGHT ANGLE PLUG,
MS-3108E-24-20S. AMPHENOL. SOLDER CONNECTION.
USED WITH BELDEN #83709 9C#16 CABLE AND BELDEN
#83715 15C#16 CABLE.
MS12P
TWELVE PIN CONNECTOR, MALE PLUG, MS-3106A-24-12P,
SOLDER CONNECTIONS.
MULTIBUS POWER
MS12S
TWELVE PIN CONNECTOR, FEMALE PLUG, MS-3106A-24-12S,
SOLDER CONNECTIONS.
MULTIBUS POWER
MS12SA
TWELVE PIN CONNECTOR, FEMALE PLUG, ITT CANNON
MS-3116F-14-12S, SOLDER CONNECTIONS.
MS13PV
THIRTEEN PIN CONNECTOR. INSERT: MOLDED SILICONE
RUBBER PER ZZ-R-765, CLASS 2B, GRADE 50, COLOR RED.
OPERATING VOLTAGE:5XVDC DIELECTRIC TESTING 7.5 KVDC
RATED. MFG CANTON P/N 3100A-CC18-13P.
MS13SV
THIRTEEN PIN CONNECTOR, SHELL: MS SIZE28
ALUMINUM PER MIL-C-5015. INSERT: MOLDED SILICONE
RUBBER PER ZZ-R-765, CLASS 2B, GRADE 70, COLOR RED.
MFG CANTON P/N 3106A-CC18-13S.
MS14P
FOURTEEN PIN CONNECTOR, MALE PLUG, ITT CANNON
MS-3106F-20-27P, SOLDER CONNECTIONS.
8/8/2011
6PR22IS
3PR24IS
140
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
MS16P
SIXTEEN PIN CONNECTOR, MALE, MS-3126F-20-16P,
SLAC S/N59-299-210-62. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
SEP PLATES/SSI
KICKER/SSI
12C16T6V, 8PR16TS,
19C16/3V
MS16PS
SIXTEEN PIN CONNECTOR, MALE, STRAIGHT PLUG,
SOLDER PINS, ITT-CANNON P/N MS3106A-24-5P.
MS16S
SIXTEEN PIN CONNECTOR, MS-3126F-20-16S,
SLAC S/N59-299-210-12. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
VAR XFMR
19C16/3V
MS16SS
SIXTEEN PIN CONNECTOR, FEMALE, STRAIGHT PLUG,
SOLDER PINS, ITT-CANNON P/N MS3106A-24-5S.
MS19P
NINETEEN PIN CONNECTOR, MALE PLUG, MS-3126F-14-19P,
SLAC S/N59-299-210-57. USE HAND CRIMP TOOL M10S-1
WITH DIE S7 AND STOP SL-3A ONLY.
MPS
12PR22OS
MS19S
NINETEEN PIN CONNECTOR, FEMALE PLUG, MS-3126F-14-19S,
SLAC S/N59-299-210-07. USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-6A AND STOP SL-3A ONLY.
FLOW SW
26C22/3C, 11PR22OS,
18PR22OS, 8PR22OS
MS19SA
NINETEEN PIN CONNECTOR, FEMALE PLUG, MS-3116F-14-19S.
SLMO
9PR18OS
MS20P
TWENTY PIN CONNECTOR, MALE PLUG, SOLDER CONNECTIONS,
ITT CANNON, MS3106-28-16P.
MS20S
TWENTY PIN CONNECTOR, FEMALE PLUG, SOLDER CONNECTIONS,
ITT CANNON, MS3106B-28-16S.
MS21P
TWENTY-ONE PIN CONNECTOR, MALE PLUG, MS-3126F-22-21P,
SLAC S/N59-299-210-65. USE HAND CRIMPING TOOL M10S-1 WITH
DIE S-7 AND STOP SL-2 ONLY.
12C20J, 19C16T3V,
26C16T3V
MS21S
TWENTY-ONE PIN CONNECTOR, FEMALE PLUG, MS-3126F-22-21S,
SLAC S/N59-299-210-15. USE HAND CRIMPING TOOL M10S-1 WITH
DIE S-7 AND STOP SL-2 ONLY.
19C16T3V, 26C16T3V
MS21SW
TWENTY-ONE PIN CONNECTOR, FEMALE PLUG,
MS-3126F-22-21SW, KEYED IN THE 'W' POSITION, 16 DEGREES
OFF CENTER. NOT IN SLAC STORES, USE HAND CRIMPING TOOL
M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY. WIRE IN COLOR
CODE SEQUENCE. FOLD BACK THE UNUSED WIRES. SEE THE WIRE
TYPE FOR THE COLOR CODE.
8/8/2011
19C18OS
FF PROFILE
MONITORS
26C16T3V
141
TERM
TERMINATION DESCRIPTION
MS24PS
TWENTY-FOUR PIN CONNECTOR, MALE, STRAIGHT PLUG, SOLDER
PINS, ITT-CANNON P/N MS3106A-24-28P.
12PR22SS
MS24SS
TWENTY-FOUR PIN CONNECTOR, FEMALE, STRAIGHT PLUG,
SOLDER PINS, ITT-CANNON P/N MS3106A-24-28S.
12PR22SS
MS2411S
CONNECTORS, CIRCULAR, PLUG SOCKET, 97 SERIES,
9 CONTACTS, FEMALE 24 SHELL, ALUMINUM ALLOY BODY,
700 VDC/500 VRMS, SOLDER TERMINATION. NEWARK InOne
PART No: 91F8349, MANUFACTURER: AMPHENOL,
MANUFACTURER PART # 97-3106A-24-11S
MS26P
TWENTY-SIX PIN CONNECTOR, MALE PLUG,
MS-3126F-16-26P SLAC S/N59-299-210-59. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-6A AND STOP SL-3A ONLY.
MS26PG
USE AN MS26P CONNECTOR, AND WIRE PER THE
INSTRUCTIONS FOR THAT CONNECTOR. CONNECT A SHORT
LENGTH OF #20 AWG STRANDED GREEN (ONLY) WIRE TO
THE OVERALL SHIELD DRAIN WIRE, AND ATTACH THIS GREEN
WIRE TO THE SHELL OF THE CONNECTOR, USING AN LRR#6 LUG
UNDER ONE SCREW OF THE CABLE CLAMP.
MS26S
TWENTY-SIX PIN CONNECTOR, FEMALE PLUG,
MS-3126F-16-26S, SLAC S/N59-299-210-09.
USE HAND CRIMPING TOOL M10S-1 WITH
DIE S-6A AND STOP SL-3A ONLY.
MS26SA
TWENTY-SIX PIN CONNECTOR, FEMALE PLUG, SOLDER
CONNECTIONS. ITT-CANNON, P/N MS3106F-28-12S
MS27P
TWENTY-SEVEN PIN CONNECTOR, MALE PLUG, SOLDER PINS,
ITT-CANNON, P/N MS3106F-20-27P.
MS32P
THIRTY-TWO PIN CONNECTOR, MALE PLUG,
MS-3126F-18-32P, SLAC S/N 59-299-210-61. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
MS32S
THIRTY-TWO PIN CONNECTOR, FEMALE PLUG,
MS-3126F-18-32S, SLAC S/N59-299-210-11. USE HAND
CRIMPING TOOL M10S-1 WITH DIE S-7 AND STOP SL-2 ONLY.
MS41P
FORTY-ONE PIN CONNECTOR, MALE PLUG, MS-3126F-20-41P,
SLAC S/N59-299-210-64. USE HAND CRIMPING TOOL M10S-1
WITH DIE S-6A AND STOP SL-3A ONLY.
8/8/2011
APPLICATION
KICKER
USED ON CABLE TYPE
26C16T3V
15PR22OS
KICKER,LIMIT SW
26C16/3V, 13PR22OS,
12C22T3V, 15PR22OS
12C18OS
KICKER/SSI
15PR22OS, 12PR22OS,
19C16T3V, 19PR24OS
19PR24OS,20C20OS
HEADSET,INTERCOM
19PR22IS
142
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
MS41S
FORTY-ONE PIN CONNECTOR, FEMALE PLUG, MS-3126F-20-41S,
USE HAND CRIMPING TOOL M10S-1 WITH DIES-6A AND
STOP SL-3A ONLY.
HEADSET,INTERCOM
19PR22IS
MTPFMMU
UNICAM MTP-COMPATIBLE, LASER-OPTIMIZED, 50 Um, MULTIMODE
CONNECTOR, 12-FIBER BLACK HOUSING AND AQUA BOOT, NO
(ALIGNMENT) PINS, (FEMALE). CORNING PART NUMBER 93-051-69-X
MTPFSMU
UNICAM MTP-COMPATIBLE, SINGLE-MODE CONNECTOR, 12-FIBER
GREEN HOUSING AND GREEN BOOT, NO (ALIGNMENT) PINS, (FEMALE).
CORNING PART NUMBER 93-201-69
N-PLIC
COAXIAL CONNECTOR, TYPE N PLUG TERMINATES ON ANDREWS
HELIAX 1 5/8" HJ7-50A ANDREWS N-FEMALE P/N H7PNF NON
TUNABLE. BCS MPS PLIC.
NK-M8
EIGHT PIN CONNECTOR, MALE,AWG 8,PN:NK-M8-21C, STANDARD-K,
MFR:PEI-GENESIS.
N1/4HP
COAXIAL CONNECTOR, TYPE-N MALE, 1/4" FSJ1-50 HELIAX
CABLE PLUG ANDREW CAT. #41W, #41ASW, #C41SW, F1PNM-H.
1/4HEL,1/4HELS
N1/2HA
COAXIAL CONNECTOR, TYPE-N MALE 1/2" LDF4-50A
CABLE PLUG ANDREW CAT. #L4PNM
1/2HELA
N1/2HC
COAXIAL CONNECTOR, TYPE N, MALE, ANDREWS P/N F4PNMV2-HC,
50 OHM SYSTEM: LCLS RF SYSTEM
1/2HELSF
N1/2HD
COAXIAL CONNECTOR, TYPE-N, MALE, ANDREWS P/N 74AW,
MODIFIED ACCORDING TO DRWG SA-236-041-14.
1/2HELGF
N1/2HG
COAXIAL CONNECTOR, TYPE-N, FEMALE, ANDREWS P/N 74AN,
MODIFIED ACCORDING TO DRWG SA-236-041-14.
1/2HELGF
N1/2HJ
COAXIAL CONNECTOR, TYPE-N FEMALE JACK, 1/2" LDF4-50
HELIAX CABLE JACK. ANDREW CAT. #L44N. TERMINATE IN
ACCORDANCE WITH ANDREW BULLETIN 373838.
RF SYSTEM
1/2HEL, 1/2HELS
N1/2HP
COAXIAL CONNECTOR, TYPE-N MALE, 1/2" LDF4-50 OR
FSJ14-50B HELIAX CABLE PLUG. ANDREW CAT. #L44W
OR 44ASW. TERMINATE IN ACCORDANCE WITH
ANDREW BULLETIN 373838.
RF SYSTEM
FEEDBACK CAVITY
1/2HEL, 1/2HELS
8/8/2011
2.0HEL
143
TERM
TERMINATION DESCRIPTION
N1/2MJ
COAXIAL CONNECTOR, TYPE-N FEMALE, 1/2" FSJ4-50B
HELIAX CABLE JACK, MODIFIED, ANDREW P/N 44ASN-15,
REXOLITE INSERT.
1/2HELX4
N1/2MR
COAXIAL CONNECTOR, TYPE-N MALE, 1/2" FSJ4-50B
HELIAX CABLE PLUG, ANDREW P/N 203540, REXOLITE INSERT.
1/2HELX4
N3/8HP
COAXIAL CONNECTOR, TYPE-N MALE, 3/8" LDF2-50 HELIAX
CABLE PLUG. ANDREW CAT. #L42W, L2TNM-PL. TERMINATE IN
ACCORDANCE WITH ANDREW BULLETIN #7576087 REV. C.
3/8HEL
N5/8HA
COAXIAL CONNECTOR, TYPE-N, FOR ANDREW LDF4.5-SERIES
5/8" ANNULAR-CORRUGATED HELIAX. ANDREW PART
NUMBER: L4.5PNM-RC
N7/8GF
COAXIAL CONNECTOR, TYPE-N FEMALE JACK, 7/8" HJ5-50
HELIAX CABLE JACK. ANDREW CAT. #H5PNF. TERMINATE IN
ACCORDANCE WITH ANDREW BULLETIN 17925C.LION SYSTEM.
N7/8HJ
COAXIAL CONNECTOR, 7/8" LDF5-50 HELIAX CABLE
FEMALE JACK. ANDREW CAT. #L45N. TERMINATE IN
ACCORDANCE WITH ANDREW BULLETIN 37374C.
N7/8HP
COAXIAL CONNECTOR, 7/8" LDF5-50 HELIAX CABLE MALE
PLUG. ANDREW CAT. #L45W.
7/8HEL
N8-A
COAXIAL CONNECTOR, TYPE N CABLE PLUG, ANDREW CAT.
#10804-101.USE TRIM CODE 402M.
RG58-A
N11
SAME CONNECTOR AS N213, BUT WIRE THE OUTER SHIELD OF
THE RG-11 TO A BANANA JACK. SEE DWG. IC15.
N58P
COAXIAL CONNECTOR TYPE N PLUG TERMINATES ON AN
RG58 OR RG141 COAXIAL CABLE. AMPHENOL P/N 82-5375.
USE CRIMPING TOOL CTL-3. USE DIE SET 227-1221-57.
N200
N200BJ
8/8/2011
APPLICATION
USED ON CABLE TYPE
7/8HELGF
F SIG MLX,
POS MONT,
WALL(I)MONT
7/8HEL
DEC SYS
RG11TRI, RG11A
COAXIAL CONNECTOR, TYPE "N" MALE PLUG, TIMES
MICROWAVE SYSTEMS CAT. #TC-200-NM OR EQUIVALENT.
BPMS
LMR200,LMR200FR
COAXIAL CONNECTOR, TYPE N FEMALE BULK-HEAD JACK.
CONNEX #172217. RF CONNECTORS RFN-1022-8-C2 OR
EQUIVALENT.
BPMS
LMR200, LMR200FR
144
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
N213
COAXIAL CONNECTOR, TYPE N CABLE PLUG. KINGS CAT. NO.
KN-59-67, KN-59-132 OR KN-59-202,
SLAC S/N59-299-018-52. USE KINGS CRIMPING TOOL KTH-1000
WITH DIE KTH-2003 AND TRIM CODE 402M FOR KN-59-67 AND
KN-59-132, AND DIE KTH-2004 AND TRIM CODE 480
FOR KN-59-202.
KICKER, GENERAL
PURPOSE TRUNK.
R11TRI, RG213
RG8
N213MC
COAXIAL CONNECTOR, TYPE N CABLE PLUG. KINGS CAT. NO.
KN-59-19, MODIFIED TO SPECIFICATIONS AS SHOWN ON
DRAWING #CA-344-296-01 CONNECTOR TERMINATES AN
RG8 COAXIAL CABLE. USE KINGS CRIMPING TOOL KTH-1000
WITH DIE KTH-2003. SEE DRAWING #CA-344-296-01
FOR CABLE TRIM CODE.
INJ. KICKER
MODULATOR
RG8
N214
COAXIAL CONNECTOR, TYPE N CABLE PLUG. KINGS CAT. NO.
KN-59-68, KN-59-104 OR KN-59-105, SLAC S/N59-299-018-53.
USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2004 AND
TRIM CODE 402.
OPTL MONT
RG214
N214M
COAXIAL CONNECTOR, TYPE N CABLE PLUG. KINGS CAT.
NO.KN-59-489, MODIFIED TO SPECIFICATIONS AS SHOWN
ON DRAWING #CA-344-293-00. CONNECTOR TERMINATES
AN RG8 COAXIAL CABLE. SEE DRAWING #CA-344-293-00
FOR CABLE TRIM CODE AND TERMINATION SPECIFICATION.
ABORT KICKER
MODULATOR
RG8
N214-F
COAXIAL CONNECTOR, TYPE N CABLE JACK, KINGS
CAT-# KN39-83,SLAC P/N 59-299-018-60. USE KINGS
CRIMPING TOOL KHT-1000 WITHDIE KTH-2004 AND TRIM
CODE 402M.
RG214
N214JB
COAX CONNECTOR, TYPE N CABLE JACK, BULKHEAD,
KINGS 19-87,SLAC P/N59-299-018-64. USE KINGS
CRIMPING TOOL KTH-1000 WITH DIE KTH-2004 AND TRIM
CODE 402M.
RG214
N218
COAXIAL CONNECTOR, TYPE N CABLE PLUG, UG-167A/U,
KINGS P/N KN-59-214.
RG218R
N223
COAXIAL CONNECTOR, TYPE N CABLE PLUG, KINGS K-GRIP JR,
KINGS CAT-# KN-59-160, USE KINGS CRIMPING TOOL KTH-2061,
JACKET TRIM JIG KTJ-108 AND DIELECTRIC TRIM JIG KTD-38.
FF BPM’S
RG223,RG223X4
N240
COAXIAL CONNECTOR, TYPE N MALE PLUG
TIMES MICROWAVE SYSTEMS CAT#TC-240-NMH
OR EQUIVALENT.
BPMS
LMR240,LMR240FR
8/8/2011
145
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
N240BJ
COAXIAL CONNECTOR, TYPE N FEMALE BULKHEAD JACK. TIMES MICROWAVE SYSTEMS CAT.
#TC-240-NF-BHF, AMPHENOL #172149 OR EQUIVALENT.
BPMS,
SRRL HIGH
QUALITY
LMR240, LMR240FR
N400
COAXIAL CONNECTOR, TYPE N MALE PLUG
TIMES MICROWAVE SYSTEMS CAT. #TC-400-NMH,
EZ-400-NMH OR EQUIVALENT.
BPMS
LMR400,LMR400FR
N400BJ
COAXIAL CONNECTOR, TYPE N FEMALE BULKHEAD JACK. TIMES MICROWAVE SYSTEMS CAT.
#TC-400-NFBC-PE, EZ-400-NF-BH OR EQUIVALENT.
BPMS
LMR400,LMR400FR
N-50UV
COAXIAL CONNECTOR, TYPE N CABLE PLUG WATER PROTECTION
ACCORDING TO IP67,UV PROTECTION, 50ohm, HUBER+SUHNER
Man P/N 11 N-50-10-5/103 UV USED FOR THE WPM RF SIGNAL
N600
COAXIAL CONNECTOR, TYPE N MALE PLUG
TIMES MICROWAVE SYSTEMS CAT. # EZ-600-NMH-D
OR EQUIVALENT.
BPMS
LMR600,LMR600FR
N600BJ
COAXIAL CONNECTOR, TYPE N FEMALE BULKHEAD JACK. TIMES MICROWAVE SYSTEMS CAT.
#EZ-600-NF-BH OR EQUIVALENT.
BPMS
LMR600,LMR600FR
OPAL-Y
SLAC MADE POWER CABLE TO FEED AN OPAL 1000
CAMERA AND A EDT RCX CAMERALINK TO FIBER CONVERTER.
DETAILS FOR THE OPAL-Y CONNECTIONS ARE SHOWN IN
DRAWING CA-261-801-31 .
OPTIC
THIS CONNECTOR IS AN OVERALL NAME OF THE CONNECTOR
THAT THE FACTORY INSTALLS ON A FIBER OPTIC CABLE. THIS
CONNECTOR IS TO BE INSTALLED BY QUALIFIED PERSONNEL ONLY.
SLD POLARIMETER
FIBER OPTICS
FIBOPT1
PC10TB-F
TEN PIN FEMALE CONNECTOR, SILVER PLATED PINS
WITH DIAMETER OF 1MM LOCATED INSIDE OF CERAMIC
ISOLATOR. MFG: RUSKIE.
MAG_PROBES
PC10TB-M
TEN PIN MALE RECEPTACLE, SILVER PLATED PINS
WITH DIAMETER OF 1MM LOCATED INSIDE OF CERAMIC
ISOLATOR. MFG: RUSKIE.
MAG_PROBES
PC32TB-F
THIRTY TWO PIN FEMALE CONNECTOR, SILVER PLATED PINS
WITH DIAMETER OF 1MM LOCATED INSIDE OF CERAMIC
ISOLATOR. MFG: RUSKIE.
MAG_PROBES
8/8/2011
WPMCOAX
146
TERM
TERMINATION DESCRIPTION
APPLICATION
PC32TB-M
THIRTY TWO PIN MALE RECEPTACLE, SILVER PLATED PINS
WITH DIAMETER OF 1MM LOCATED INSIDE OF CERAMIC
ISOLATOR. MFG: RUSKIE.
MAG_PROBES
PHONE
PHONE PLUG, 3/32" DIAMETER, 2 CONTACTS, RADIO SHACK
ARCHER P/N 274-279.
PHON-R
RIGHT ANGLE PHONE PLUG, 1/4" DIAMETER, TWO
CONTACTS, TYPE NP2RC-BAG, NEWARK CAT. #89F6034.
PHXQP1
ONE POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER.
SEE PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED
ASSEMBLY/TERMINATION DRAWING NUMBER. DO NOT STRIP
CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK
FULLY FLUSH WITH CONNECTOR BODY AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE:QP 1.5/1(BU OR GN/YE)
ORDER NUMBER: 3051108, (3051250, or 3051263).
**DO NOT USE TEFLON WIRE **
PHXQP2
TWO POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER.
SEE PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED
ASSEMBLY/TERMINATION DRAWING NUMBER.DO NOT STRIP
CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK
FULLY FLUSH WITH CONNECTOR BODY AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE: QP 1.5/2
ORDER NUMBER: 3051111. SEE “SELF-ASSEMBLED COMBI PLUGS
WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT “CLIPLINE”
CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
8/8/2011
USED ON CABLE TYPE
147
TERM
TERMINATION DESCRIPTION
PHXQP3
THREE POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER.
SEE PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED
ASSEMBLY/TERMINATION DRAWING NUMBER. DO NOT STRIP
CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK
FULLY FLUSH WITH CONNECTOR BODY AND LOCK CONDUCTOR IN
PLACE.MANUFACTURER: PHOENIX CONTACT. TYPE: QP 1.5/3
ORDER NUMBER: 3051124. SEE “SELF-ASSEMBLED COMBI PLUGS
WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT
“CLIPLINE” CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXQP4
FOUR POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM LEFT
AT 1 WITH COMBI CONNECTOR KEYS FACING USER. SEE PIN
LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED ASSEMBLY/
TERMINATION DRAWING NUMBER. DO NOT STRIP CONDUCTOR.
3/4-INCH INSERTION LENGTH. USE SCREWDRIVER IN RECTANGULAR
HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK FULLY FLUSH WITH
CONNECTOR BODY AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE: QP 1.5/4
ORDER NUMBER: 3051137. SEE “SELF-ASSEMBLED COMBI PLUGS
WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT “CLIPLINE”
CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXQP5
FIVE POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM LEFT AT 1
WITH COMBI CONNECTOR KEYS FACING USER. SEE PIN LIST FOR
CONDUCTOR ASSIGNMENT OR DETAILED ASSEMBLY/TERMINATION
DRAWING NUMBER. DO NOT STRIP CONDUCTOR. 3/4-INCH INSERTION
LENGTH. USE SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE
WIRE ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT.
TYPE: QP 1.5/5 ORDER NUMBER: 3051140. SEE “SELF-ASSEMBLED
COMBI PLUGS WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT
“CLIPLINE” CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
8/8/2011
APPLICATION
USED ON CABLE TYPE
148
TERM
TERMINATION DESCRIPTION
PHXQP6
SIX POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER.
SEE PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED
ASSEMBLY/TERMINATION DRAWING NUMBER. DO NOT STRIP
CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK
FULLY FLUSH WITH CONNECTOR BODY AND LOCK CONDUCTOR IN
PLACE. MANUFACTURER: PHOENIX CONTACT. TYPE: QP 1.5/6
ORDER NUMBER: 3051153. SEE “SELF-ASSEMBLED COMBI PLUGS
WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT
“CLIPLINE” CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXQP7
SEVEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM LEFT
AT 1 WITH COMBI CONNECTOR KEYS FACING USER. SEE PIN
LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED ASSEMBLY/TERMINATION
DRAWING NUMBER. DO NOT STRIP CONDUCTOR. 3/4-INCH INSERTION
LENGTH. USE SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE
ORANGE WIRE ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT.
TYPE: QP 1.5/7 ORDER NUMBER: 3051166. SEE “SELF-ASSEMBLED
COMBI PLUGS WITH FAST CONNECTION” SECTION OF PHOENIX CONTACT
“CLIPLINE” CATALOG FOR ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXQP8
EIGHT POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM LEFT
AT 1 WITH COMBI CONNECTOR KEYS FACING USER. SEE PIN
LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED ASSEMBLY/
TERMINATION DRAWING NUMBER. DO NOT STRIP CONDUCTOR.
3/4-INCH INSERTION LENGTH. USE SCREWDRIVER IN RECTANGULAR
HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK FULLY FLUSH WITH
CONNECTOR BODY AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE: QP 1.5/8 ORDER NUMBER:
3051179. SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR ADDITIONAL
CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
8/8/2011
APPLICATION
USED ON CABLE TYPE
149
TERM
TERMINATION DESCRIPTION
PHXQP9
NINE POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING
STARTS FROM LEFT AT 1 WITH COMBI CONNECTOR KEYS
FACING USER. SEE PIN LIST FOR CONDUCTOR ASSIGNMENT
OR DETAILED ASSEMBLY/TERMINATION DRAWING NUMBER. DO
NOT STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE
SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE
ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT.
TYPE: QP 1.5/9 ORDER NUMBER: 3051182. SEE “SELF-ASSEMBLED
COMBI PLUGS WITH FAST CONNECTION” SECTION OF PHOENIX
CONTACT “CLIPLINE” CATALOG FOR ADDITIONAL
CONFIGURATION OPTIONS.**DO NOT USE TEFLON WIRE **
PHXQP10
TEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER. SEE
PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED ASSEMBLY/
TERMINATION DRAWING NUMBER. DO NOT STRIP CONDUCTOR. 3/4-INCH
INSERTION LENGTH. USE SCREWDRIVER IN RECTANGULAR HOLE TO
ROTATE ORANGE WIRE ENTRY BLOCK FULLY FLUSH WITH CONNECTOR
BODY AND LOCK CONDUCTOR IN PLACE. MANUFACTURER:
PHOENIX CONTACT.TYPE: QP 1.5/10 ORDER NUMBER: 3051195.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXQP11
ELEVEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING
STARTS FROM LEFT AT 1 WITH COMBI CONNECTOR KEYS
FACING USER. SEE PIN LIST FOR CONDUCTOR ASSIGNMENT
OR DETAILED ASSEMBLY/TERMINATION DRAWING NUMBER. DO
NOT STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE
SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE
ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT
TYPE: QP 1.5/11 ORDER NUMBER: 3051205.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
8/8/2011
APPLICATION
USED ON CABLE TYPE
150
TERM
TERMINATION DESCRIPTION
PHXQP12
TWELVE POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING STARTS FROM
LEFT AT 1 WITH COMBI CONNECTOR KEYS FACING USER.
SEE PIN LIST FOR CONDUCTOR ASSIGNMENT OR DETAILED
ASSEMBLY/TERMINATION DRAWING NUMBER. DO NOT STRIP
CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY
BLOCK FULLY FLUSH WITH CONNECTOR BODY AND LOCK
CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT
TYPE: QP 1.5/12 ORDER NUMBER: 3051218.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.**DO NOT USE TEFLON WIRE **
PHXQP13
THIRTEEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING
STARTS FROM LEFT AT 1 WITH COMBI CONNECTOR KEYS
FACING USER. SEE PIN LIST FOR CONDUCTOR ASSIGNMENT
OR DETAILED ASSEMBLY/TERMINATION DRAWING NUMBER. DO
NOT STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE
SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE
ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT
TYPE: QP 1.5/13 ORDER NUMBER: 3051221.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.**DO NOT USE TEFLON WIRE **
PHXQP14
FOURTEEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING
STARTS FROM LEFT AT 1 WITH COMBI CONNECTOR KEYS
FACING USER. SEE PIN LIST FOR CONDUCTOR ASSIGNMENT
OR DETAILED ASSEMBLY/TERMINATION DRAWING NUMBER. DO
NOT STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE
SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE
ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT
TYPE: QP 1.5/14 ORDER NUMBER: 3051234.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.**DO NOT USE TEFLON WIRE **
8/8/2011
APPLICATION
USED ON CABLE TYPE
151
TERM
TERMINATION DESCRIPTION
PHXQP15
FIFTEEN POSITION CONNECTOR, "COMBI" TYPE PLUG,
"QUICKCON" INSULATION DISPLACEMENT TERMINATION.
WIRE RANGE: 24-16 AWG. PIN NUMBERING
STARTS FROM LEFT AT 1 WITH COMBI CONNECTOR KEYS
FACING USER. SEE PIN LIST FOR CONDUCTOR ASSIGNMENT
OR DETAILED ASSEMBLY/TERMINATION DRAWING NUMBER. DO
NOT STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE
SCREWDRIVER IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE
ENTRY BLOCK FULLY FLUSH WITH CONNECTOR BODY AND
LOCK CONDUCTOR IN PLACE. MANUFACTURER: PHOENIX CONTACT
TYPE: QP 1.5/15 ORDER NUMBER: 3051247.
SEE “SELF-ASSEMBLED COMBI PLUGS WITH FAST CONNECTION”
SECTION OF PHOENIX CONTACT “CLIPLINE” CATALOG FOR
ADDITIONAL CONFIGURATION OPTIONS.
**DO NOT USE TEFLON WIRE **
PHXTB2
TWO POSITION TERMINAL BUS, DIN RAIL MOUNT,
10MM BOLT DIAMETER RING LUG TERMINATION,
WIRE SIZE: 6 AWG TO 1/0 AWG.
PHOENIX CONTACT TYPE: UHV 50-AS/AS, P/N:2130017 .
P15QTC
ONE POSITION TERMINAL BLOCK, DIN RAIL MOUNT, WIRE RANGE:
24-16AWG,(QTC 1,5), TERMINATE CONDUCTOR TO SPECIFIED"QUICKCON"
INSULATION DISPLACEMENT CONNECTOR ON TERMINAL BLOCK. DO NOT
STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK FULLY
FLUSH WITH TERMINAL BLOCK AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE: QTC 1,5(BU OR -PE)
ORDER NUMBER: 3205019, (3205022, OR 3205035).
SEE PHOENIX CONTACT "CLIPLINE" CATALOG FOR ADDITIONAL
TERMINAL BLOCK OPTIONS THAT INCLUDE "QUICKCON" INSULATION
DISPLACEMENT CONNECTION.
**DO NOT USE TEFLON WIRE **
P25QTC
ONE POSITION TERMINAL BLOCK, DIN RAIL MOUNT, WIRE RANGE:
20-14AWG,(QTC 2,5), TERMINATE CONDUCTOR TO SPECIFIED"QUICKCON"
INSULATION DISPLACEMENT CONNECTOR ON TERMINAL BLOCK. DO NOT
STRIP CONDUCTOR. 3/4-INCH INSERTION LENGTH. USE SCREWDRIVER
IN RECTANGULAR HOLE TO ROTATE ORANGE WIRE ENTRY BLOCK FULLY
FLUSH WITH TERMINAL BLOCK AND LOCK CONDUCTOR IN PLACE.
MANUFACTURER: PHOENIX CONTACT. TYPE: QTC 2,5(BU OR -PE)
ORDER NUMBER: 3209416, (3206429, OR 3206432).
SEE PHOENIX CONTACT "CLIPLINE" CATALOG FOR ADDITIONAL
TERMINAL BLOCK OPTIONS THAT INCLUDE "QUICKCON" INSULATION
DISPLACEMENT CONNECTION.**DO NOT USE TEFLON WIRE **
8/8/2011
APPLICATION
USED ON CABLE TYPE
152
TERM
TERMINATION DESCRIPTION
PLB06P
6 PIN, 2 ROW, MALE CONNECTOR, TOP OPENING HOOD.
POSITRONIC INDUSTRIES, CODE NUMBER PLB06M0050.
PLB06S
6 PIN, 2 ROW, FEMALE CONNECTOR, TOP OPENING HOOD.
POSITRONIC INDUSTRIES, CODE NUMBER PLB06F0050.
PLC30P
30 PIN, 3 ROW, MALE CONNECTOR, TOP OPENING HOOD.
POSITRONIC INDUSTRIES, CODE NUMBER PLC30M0050.
PLC30S
30 PIN, 3 ROW, FEMALE CONNECTOR, TOP OPENING HOOD.
POSITRONIC INDUSTRIES, CODE NUMBER PLC30F0050.
POS19PS
CONNECTOR, POSITRONIX FRONT RUNNER SERIES,SIZE 19
HOUSING, FREE IN LINE MALE CONTACTS W/PLUGHOUSING,
19 PINS-SIZE 20, EMI/RFI SHIELDED SERVICE CLASS,
SHORT-STRAIGHT EMI/RFI CABLE ADAPTOR HOOD.
POSITRONIX PART NUMBER - FR19MP1920M6.(USES SIZE 20
REMOVABLE MALE (PIN) CONTACTS P/N MC720N3)
POS19RS
CONNECTOR, POSITRONIC FRONT RUNNER SERIES,SIZE 19
HOUSING, FREE IN LINE FEMALE CONTACTS W/PLUGHOUSING,
19 PINS-SIZE 20, EMI/RFI SHIELDED SERVICE CLASS,
SHORT-STRAIGHT EMI/RFI CABLE ADAPTOR HOOD.
POSITRONIC PART NUMBER - FR19FP1920M6(USES SIZE 20
REMOVABLE FEMALE (PIN) CONTACTS P/N FC720N2)
PP50G
CONNECTOR, MALE, 50 A, 125-250 VOLT AC OR DC CURRENT
RUPTURING. SUPERIOR ELECTRIC CAT-# PP50GB.
PP75-B
ANDERSON POWERPOLE 75 AMP LOCKING CONNECTOR,PP75
LOCKING HOUSING 75LOKBLK "BLACK" MCORS, TSP, QMS.
PP75-R
ANDERSON POWERPOLE 75 AMP LOCKING CONNECTOR,PP75
LOCKING HOUSING 75LOKRED "RED" MCORS, TSP, QMS.
PP100G
CONNECTOR, MALE, 100A, 125-250 VOLTS AC OR DC CURRENT
RUPTURING. SUPERIOR ELECTRIC CAT-# PP100GB.
PP180A
CONNECTOR PLUG, MALE, 18AMP P/N 1381G1 (BLACK),
1381G2 (WHITE). USEP/N 1383 CONTACT FOR #2 AWG.
MCOR
PP180-B
ANDERSON POWERPOLE 180AMP CONNECTOR, PP180 SERIES
HOUSING 1381G1 "BLACK"
MCOR
8/8/2011
APPLICATION
USED ON CABLE TYPE
#1-AL
#2
153
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
PP180C
ANDERSON POWERPOLE 180AMP CONTACT, 1/0 WIRE SIZE
USE WITH PP180 SERIES HOUSING, ANDERSON POWER P/N 1382.
MCOR
#1/0-FLEX
PP180-R
ANDERSON POWERPOLE 180AMP CONNECTOR, PP180 SERIES
HOUSING 1381G3 "RED"
MCOR
PPR8
8 POLE RECEPTACLE, ANDERSON POWERPOLE CAT. #1454G1
POWERPOLE PAK RECEPTACLE.
MCOR DC OUT
2C12OS
PREFAB
CABLE AND CONNECTOR DETAILS ARE PROVIDED BY
OUTSIDE VENDOR.
PS50/2
CONNECTORS RS50G & PP50G ARE USED. WIRE AS FOLLOWS:
RS50G TO "R" & PP50G TO "G".
PT8S
8 PIN CONNECTOR, FEMALE, BENDIX P/N PT06A-X-8S
SLMO
4PR22OS
PUSHON
THIS INDICATES A CONNECTION WHERE THE WIRE IS
PUSHED ONTO THE TERMINATION POINT AS PART OF THE FIELD
INSTALLATION OF A CABLE.
RG58C/U
COAXIAL CONNECTOR, SLEEVE, CONTACT, F/COAXIAL,
KINGS K-GRIP (FERRULE), PART No. 1205-19-5
FOR CRIMPING USE DIE SIZE 42. SLAC S/N 59-299-009-01.
RG-6QS
CONTROLNET BNC PLUG RG-6QS USE 1786-CTK TOOLKIT
WITH 2082 DIE SET AND CRIMP SETTING OF 4 ALLEN BRADLEY
PN# 1786-BNC/B.
RJ12
SIX PIN CONNECTOR WITH ONE PIECE CONSTRUCTION AND
PRELOADED CONTACTS. RATED 150V @1.5 MAX.
AMP P/N# 5.5551777-3 OR EQUIVALENT.
RJ45
EIGHT PIN CONNECTOR WITH ONE PIECE CONSTRUCTION AND
PRELOADED CONTACTS. RATED 250 VAC@2A MAX. TENSILE
STRENGTH (CABLE TO PLUG) 20 LBS. AMP P/N#5.641339-3
OR EQIVALENT.
RS50G
CONNECTOR, FEMALE, 50A, 125-250 VOLT AC OR DC CURRENT
RUPTURING. SUPERIOR ELECTRIC CAT-# RS50GWT.
RS100G
CONNECTOR, FEMALE, 100A, 125-250 VOLTS AC OR DC CURRENT
RUPTURING. SUPERIOR ELECTRIC CAT-# RS100GWT.
8/8/2011
19PR22IS
CONTROLNET
RG6-QF
#1-AL
154
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
RTDS
SPECIAL THREE PIN FEMALE CONNECTOR, WHITE SHELL. MATES
WITH RTD-MOUNTED PLUG. OMEGA P/N OPT-U-F.
S1/2RP
COAXIAL CONNECTOR FOR 1/2" SEMI-RIGID JT-4500 SERIES
COAXIAL CABLE. GILBERT PART NO. GRS-500-CH-DU-03. SEE
THE GILBERT CATALOG FOR TRIM AND ASSEMBLY INSTRUCTIONS.
CATV SYSTEM
1/2”RD, 1/2"RDB
S3/4RP
COAXIAL CONNECTOR FOR 3/4" SEMI-RIGID JT-4750 SERIES
COAXIAL CABLE. GILBERT PART NO. GRS-750-CH-DU-01.SEE THE
GILBERT CATALOG FOR TRIM AND ASSEMBLY INSTRUCTIONS.
CATV SYSTEM
3/4”RGD
SC
FIBER OPTIC CONNECTOR. TYPE 'SC' UNICAM CONNECTOR,
CERAMIC TIP,ROTATING CAM; INSERTION LOSS: 0.3Db TYPICAL;
NOMINAL FIBER O.D.:125um; MFG SIECOR,
MULTIMODE P/N 95-000-41, SINGLEMODE P/N 95-200-41.
SC760
SWITCHCRAFT LOW VOLTAGE POWER CONNECTOR. CONNECTOR IS
FEMALE TYPE WITH A 2.1 MM CENTER HOLE AND BLACK SHIELD.
DISTRIBUTOR ALLIED INDUSTRIES
POWER PLUG MFR. PART#: 760 ALLIED STOCK#: 932-0760
SCS760
SWITCHCRAFT LOW VOLTAGE POWER CONNECTOR. CONNECTOR IS
FEMALE TYPE WITH A 1.6 MM CENTER HOLE AND BLACK SHIELD.
DISTRIBUTOR ALLIED INDUSTRIES
POWER PLUG MFR. PART#: S760 ALLIED STOCK#: 932-9999
SCSI-2
FIFTY PIN CONNECTOR. SHIELDED PLUG WITH ASSEMBLED
STANDARD TERMINATION COVERS. AMPLIMITE SERIES III
THERMOPLASTIC, MFG AMP P/N 749111-4.
SHV-C
COAXIAL CONNECTOR, 5KV, SHV CABLE PLUG, KINGS NO.
1705-16-M06, SLAC S/N 59-299-035-16 FOR
THE STANDARD TYPE INSULATION MATERIAL. KINGS NO.
1705-16-11, SLAC S/N 59-299-035-15 FOR
THE REXOLITE INSULATION TYPE. USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-2061 AND TRIM CODE 441.
SHV-10K
COAXIAL PLUG CONNECTOR FOR DC CONNECTIONS ONLY. RATED UP TO
10KV OF DC, TYPICAL PART: KINGS ELECTRONICS: 1065-2.
2PR24IS
TYPE-C
http://www.kingselectronics.com/Portals/0/SalesPDF/1065-2_SD.pdf
SHVMOD
8/8/2011
SLAC BUILT HV CONNECTOR. USED ON 1/4" HELB
HELIAX CABLE. USED BY CONTROLS DEPARTMENT.
1/4" HELB
155
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
SHV58
COAXIAL CONNECTOR, SHV CABLE PLUG, 5KV. KINGS NO.
1705-2,SLAC S/N59-299-035-11. USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-2061 AND TRIM CODE 441.
FAST SENSOR
RG58R
SHV59J
COAXIAL CONNECTOR, 5KV, SHV BULKHEAD JACK. KINGS NO.
1702-1, SLAC S/N59-299-035-68. USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-2062 AND TRIM CODE 441.
RG59R
SHV59
COAXIAL CONNECTOR, 5KV, SHV CABLE PLUG. KINGS NO.
1705-1,SLAC S/N 59-299-035-12. USE KINGS CRIMPING
TOOL KTH-1000 WITH DIE KTH-2062 AND TRIM CODE 418.
RG59R
SHV214
COAXIAL CONNECTOR 5KV, SHV CABLE PLUG, KINGS
CAT#1705-4, SLAC S/N59-299-035-14. USE KING CRIMPING TOOL
KTH-1000 WITH DIE KTH-1079 AND TRIM CODE 457.
SL1808B
EIGHT PIN CONNECTOR, PC BOARD TO CABLE, TWO PIECE SNAP
LOCK DESIGN. SOLDERS TO PC BOARD. CABLE END TERMINATES
TO CONNECTOR WITH INTEGRATED SET SCREWS.
WEIDMULLER CAT#123676. USED FOR REVERSING SWITCH CONTROLLER.
SLAC7
SLAC BUILT SEVEN PIN CONNECTOR. USED TO MONITOR THE
POWER SUPPLIES IN A NIM CRATE. USED BY SLAC CONTROLS DEPT.
4PR22OS
SMA3/8H
COAXIAL CONNECTOR, TYPE SMA, MALE. ANDREWS P/N E2TSM,
SMA STRAIGHT MALE CONNECTOR FOR EFX2-50, LDF2-50 SYSTEM:
LCLS RF SYSTEM.
EFX2RN-50
LDF2-50(3/8HELSF)
SMA58
COAXIAL CONNECTOR, SMA STRAIGHT CABLE PLUG. SEALECTRO
NO. 50-624-9141-31 OR OMNI/SPECTRA P/N 2036-5014-00,
MOD. #636-2A.
FFTB VAC
RG58
SMA214
TERMINATE CABLE USING AN N214-F CONNECTOR, THEN
INSTALL AN SMA/N ADAPTER.
SPECIAL BPM
CABLES
EG214
SMA223
COAXIAL CONNECTOR, SMA STRAIGHT CABLE PLUG.
SELECTRO NO. 50-622-9142-31 OR CABLEWAVE NO.545-001
OR SOLITRON NO. 2900-6001, KINGS NO. 875-5-3, USE
CRIMPING DIE SET KTH-2001, JACKET TRIM JIG KTJ-78,
DIELECTRIC TRIM JIG KTD-116, TRIM CODE 432.
SLAC S/N59-299-040-01.
BEAM POSITION
MONITORS
RG223X4
SMA240
TYPE SMA MALE PLUG CONNECTOR FOR LMR-240 STAINLESS
STEEL W/ GOLD PLATED BERYLLIUM COPPER 50 OHMS 1000
VOLTS(RMS MAX)1.25:1 UP TO 2 GHz.
8/8/2011
LMR240
156
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
SMA/N
ADAPTER, SMA FEMALE TO N FEMALE, PANEL MOUNT (BULKHEAD
ADAPTER), PASTERNAK ENTERPRISES CAT-# PE-9104.
SLC FF BPM'S
RG223, RG214
SMR223
COAXIAL CONNECTOR, SMA RIGHT ANGLE CABLE PLUG.
SELECTRO NO.50-628-9142-30 OR CABLEWAVE NO. 555-001 OR
SOLITRON NO. 2910-6001, KINGS NO. 876-11-3, USE
CRIMPING DIE SET KTH-2001, JACKET TRIM JIG KTJ-78,
DIELECTRIC TRIM JIG KTD-116, TRIM CODE 432.
NOT IN STORES.
BEAM POSITION
MONITORS
RG223,RG223X4
SMS9P
NINE PIN CONNECTOR, MALE, BURNDY P/N SMS-9P-1
SMS12P
TWELVE PIN CONNECTOR, MALE, BURNDY P/N SMS-12P-1
SOLDER
THIS INDICATES A CONNECTION WHERE THE INDICATED
WIRE IS SOLDERED DIRECTLY TO THE INDICATED
TERMINATION POINT, AS PART OF THE FIELD INSTALLATION
OF THE INDICATED CABLE.
SP1/2H
COAXIAL SPLICE FOR 1/2" LDF4-50 HELIAX CABLE. ANDREW
CAT. NO. L44Z. CONNECT IN ACCORDANCE WITH ANDREW
BULLETIN 37384.
CABLE SPLICES
1/2HEL,1/2HELS
SP7/8H
COAXIAL SPLICE FOR 7/8" LDF5-50 HELIAX CABLE. ANDREW
CAT. NO. L45Z. CONNECT IN ACCORDANCE WITH ANDREW
BULLETIN 37381.
CABLE SPLICES
7/8HEL
SPEC
THIS TYPE OF TERMINATION IS USED ONLY FOR SPECIAL PULSED
COAXIAL CABLE CONNECTIONS, SUCH AS KICKER HIGH VOLTAGE
CONNECTIONS. ONLY SYSTEM SPECIALISTS ARE TO TERMINATE
AND MAKE CONNECTIONS.
S&T
THIS INDICATES A WIRE IS STRIPPED AND TINNED AND
CONNECTED TO THE DESIGNATED POINTS.
ST
FIBER OPTIC CONNECTOR. TYPE 'ST' UNICAM CONNECTOR,
CERAMIC TIP, ROTATING CAM; INSERTION LOSS: 0.3Db TYPICAL;
NOMINAL FIBER O.D.:125um; MFG SIECOR,
MULTIMODE P/N 95-000-51, SINGLEMODE P/N 95-200-51.
STARCEL
SPECIAL CONNECTOR, HIGH VOLTAGE FOR VARIAN ION PUMP.
MFG: GAMMA VACUUM, ADDRESS: 2915 133RD STREET WEST,
SHAKOPEE, MN 55379. MFG P/N 380101
8/8/2011
27PR22OS, 1PR20OS,
12PR22SS
TYPE-C
157
TERM
TERMINATION DESCRIPTION
STRIP
THIS INDICATES A CONNECTION WHERE THE INDICATED WIRE
IS STRIPPED TO THE PROPER LENGTH, INSERTED INTO THE
TERMINAL AND THE SCREW TIGHTENED TO MANUFACTURE SPECIFIED
TORQUE, AS PART OF THE FIELD INSTALLATION OF THE INDICATED
CABLE,ALUMINUM WIRES MUST BE INSTALLED USING AN OXIDE
INHIBITING ELECTRICAL JOINT COMPOUND (SEE GENERAL NOTE #8
AT THE BEGINNING OF THIS DOCUMENT).
STRP-A
STRIP 3/8 OF AN INCH OF INSULATION FROM THE ENDS OF
THE PAIR WIRES. USING THE WIRE COLOR-CODE FROM TABLE 1,
CONNECT THE FIRST WIRE OF THE PAIR TO THE '+' POINT,
THE SECOND WIRE TO THE '-' POINT, AND THE SHIELD TO
THE 'G' POINT.
TC-CAKP
TWO PIN, MALE, ‘K-TYPE’ THERMOCOUPLE CONNECTOR.
OMEGA CAT. #SMPW-CC-K-M. SCREW TENSION CONNECTIONS,
BEIGE SHELL,COMPENSATING ALLOY IN CONNECTOR IS ‘+’ =
CHROMEGA (YELLOW WIRE)AND ‘-‘ = ALUMEL (RED WIRE).
TC-CCF
TWO PIN FEMALE CONNECTOR, FLAT TERMINALS, SCREW TENSION
CONNECTIONS, COLOR OF SHELL IS BLUE, COMPENSATING ALLOY
USED IN CONNECTOR IS '+' = COPPER, '-' = CONSTANTAN.
OMEGA CAT. #SMP-T-F.
TC-CCM
TWO PIN MALE CONNECTOR, FLAT TERMINALS, SCREW
TENSION CONNECTIONS, COLOR OF SHELL IS BLUE,
COMPENSATING ALLOY USED IN CONNECTOR IS '+' = COPPER,
'-' = CONSTANTAN. OMEGA CAT. #SMPW-CC-T-M.
TC-CCP
TWO PIN MALE THERMOCOUPLE CONNECTOR, OMEGA CAT.
#OST-T-M, SCREW TENSION CONNECTIONS, COLOR OF SHELL
BLUE, CONPENSATING ALLOY USED IN CONNECTOR IS '+' =
COPPER,'-' = CONSTANTAN.
1PR28CC
TC-CCS
TWO PIN FEMALE THERMOCOUPLE CONNECTOR, OMEGA CAT-#
OST-T-F, SCREW TENSION CONNECTIONS, COLOR OF SHELL
BLUE, CONPENSATING ALLOY USED IN CONNECTOR IS '+' =
COPPER, '-' = CONSTANTAN.
1PR28CC
TC-JNC
COPPER AND CONSTANTAN CONDUCTORS ARE STRIPPED BACK
APPROX. ONE INCH AND ELECTRICALLY WELDED TOGETHER ON
THE VERY END TO FORM A THERMOCOUPLE JUNCTION.
COMPLETED TC IS FASTENED INTO PLACE WITH NON-CONDUCTIVE
EPOXY AND WRAPPED WITH GLASS TAPE.
1PR28CC
8/8/2011
APPLICATION
USED ON CABLE TYPE
250MCM, 350MCM,
500MCM,#4/0,
#6-,#8-,
#10-,#12-,
2C14TYR, THRM-CU
158
TERM
TERMINATION DESCRIPTION
TC-SLV
COPPER AND CONSTANTAN CONDUCTORS ARE STRIPPED BACK
APPROX. ONE INCH AND WIRE WRAPPED ONTO EXISTING COPPER
CONSTANTAN PIGTAILS ON DISK LOADED WAVEGUIDE. A SOLDER
SLEEVE IS SOLDERED OVER EACH INDIVIDUAL CONDUCTOR AT
THE WIRE WRAP. INSULATE FINISHED CONNECTIONS WITH
SHRINK TUBING.
TCMS04S
APPLICATION
USED ON CABLE TYPE
1PR28CC
FOUR PIN, FEMALE, ‘K-TYPE’, 350 DEG CELCIUS BAKEABLE,
THERMOCOUPLE CONNECTOR. ISI CONNECTORS P/N: 9923038.
COMPENSATING ALLOY IN CONNECTOR IS ‘+’ = CHROMEL
(YELLOW WIRE) AND ‘-‘ = ALUMEL (RED WIRE).
TNC58
COAXIAL CONNECTOR, TNC CABLE PLUG. KINGS CAT.
NO. KA-59-44 OR KA-59-103, SLAC S/N59-299-016-51.
USE KINGS CRIMPING TOOL KTH-1000 WITH DIE KTH-2001
AND TRIM CODE 401.
RF SYSTEM
RG58
TNC223
COAXIAL CONNECTOR, TNC CABLE PLUG. KINGS CAT.
NO. KA-59-45 OR KA-59-87. USE KINGS CRIMPING TOOL
KTH-1000 WITH DIE KTH-2001 AND TRIM CODE 401.
OSC FANOUT
RG223
TCA02ADN
SEE TERMINAL PLUG CODE DEFINITION AT THE BEGINNING OF
THIS SECTION. MFG: PHOENIX CONTACT, P/N:1881325 ,
DESCRIPTION: COMBICON, FK-MC 0,5/2-ST-2.5 OR EQUIVALENT.
TCA06ADN
SEE TERMINAL PLUG CODE DEFINITION AT THE BEGINNING OF
THIS SECTION. MFG: PHOENIX CONTACT,P/N:1881367 ,
DESCRIPTION: COMBICON, FK-MC 0,5/6-ST-2.5 OR EQUIVALENT.
TCA12ADN
SEE TERMINAL PLUG CODE DEFINITION AT THE BEGINNING OF
THIS SECTION. MFG: PHOENIX CONTACT, P/N:1881422 ,
DESCRIPTION: COMBICON,FK-MC 0,5/12-ST-2.5 OR EQUIVALENT.
TCC02AAS
SEE TERMINAL PLUG CODE DEFINITIONS AT THE BEGINNING
OF THIS TERMINATION DESCRIPTION SECTION.
VARIOUS MANUFACTURERS.
TCC03AAN
SEE TERMINAL PLUG CODE DEFINITIONS AT THE BEGINNING
OF THIS TERMINATION DESCRIPTION SECTION.
VARIOUS MANUFACTURERS.
TCC08ABN
SEE TERMINAL PLUG CODE DEFINITIONS AT THE BEGINNING
OF THIS TERMINATION DESCRIPTION SECTION.
MFG: PHOENIX CONTACT, P/N: 1803633, DESCRIPTION: COMBICON,
MC 1.5/8-ST-3.81 OR EQUIVALENT.
8/8/2011
159
TERM
TERMINATION DESCRIPTION
TCE08ABN
SEE TERMINAL PLUG CODE DEFINITIONS AT THE BEGINNING
OF THIS TERMINATION DESCRIPTION SECTION.
MFG: PHOENIX CONTACT, P/N: 1757077, DESCRIPTION:
COMBICON, MSTB 2.5/8-ST-5.08 OR EQUIVALENT.
MFG: WEIDMULLER, P/N:1716380000, DESCRIPTION:BL 5.08/08.
TCC10AAS
SEE TERMINAL PLUG CODE DEFINITIONS AT THE BEGINNING
OF THIS TERMINATION DESCRIPTION SECTION.
VARIOUS MANUFACTURERS.
TE2S
TWO PIN CONNECTOR, FEMALE, CRIMP CONNECTIONS.
TE CONNECTIVITY P/N: 177898-1.
(SEE INFORMATION PAGE 62 )
TE12S
TWELVE PIN CONNECTOR, FEMALE, CRIMP CONNECTIONS.
TE CONNECTIVITY P/N: 917354-1.
(SEE INFORMATION PAGE 76 )
TT4P
FOUR PIN MALE CONNECTOR, BURNDY TYPE "TRIMTRIO", CAT. NO.G6F-10-4-PNE, SLAC S/N59-299-206-01.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
8/8/2011
APPLICATION
USED ON CABLE TYPE
CHOPPER
2C22MS,1PR22OS,
7C22OS
160
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
TT4PR
FOUR PIN MALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO.GOB-10-4-PNE, SLAC S/N59-299-406-01.
FOR #16-20 WIRE, USE BURNDY CONTACT RM16M-23D28,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE BURNDY CONTACT RM20M-12D28,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE BURNDY CONTACT RM24M-9D28,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
CHOPPER,MAG PS
2C22MS,2PR22OS
1PR20OS,4C20OS
TT4S
FOUR PIN FEMALE CONNECTOR, BURNDY TYPE
TRIO", CAT. NO.,G6F-10-4-SNE,
SLAC S/N 59-299-206-02.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
CHOPPER,MAG PS
2C22MS,2PR22OS,
1PR20OS,4C20OS
CHOPPER,MAG PS
2C22MS,2PR22OS,
1PR20OS,4C20OS
TT4SR
8/8/2011
"TRIM
S3-1 AND
S-10 AND
S-9 AND
FOUR PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO.GOB-10-4-SNE, SLAC S/N59-299-406-02.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
161
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
TT4SW
FOUR PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO.G6F-10-4-SWE, (NOTE OFFSET KEYING).
NOT A SLAC STORES ITEM.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N 59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
RTD
2PR24IS
TT8P
EIGHT PIN MALE CONNECTOR, BURNDY TYPE "TRIMTRIO", CAT. NO.G6F-12-88-PNE,
SLAC S/N59-299-206-03.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
8/8/2011
3PR24IS,4PR18TC,
8C18OS
162
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
TT8PR
EIGHT PIN MALE CHASSIS-MOUNT CONNECTOR, BURNDY TYPE
"TRIM-TRIO" CAT. NO. G0B-12-88-PNE,
SLACS/N59-299-406-03.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N 59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
LVDT
3PR24IS,4PR22IS
TT8S
EIGHT PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO",CAT. NO. G6F-12-88-SNE,
SLAC S/N59-299-206-04.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
RF SYS
2C22MS,8C18OS,
4PR18TC
TT8SR
EIGHT PIN FEMALE CHASSIS-MOUNT CAT.
NO. G0F-12-88-SNE, SLAC S/N59-299-406-04.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND STOP SL-40 ONLY.
8/8/2011
4PR18TC
163
TERM
TERMINATION DESCRIPTION
TT12P
TWELVE PIN MALE CONNECTOR, BURNDY TYPE
TRIO", CAT. NO. G6F-14-92-PNE,
SLAC S/N59-299-206-05.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
TT12PR
8/8/2011
APPLICATION
"TRIM-
USED ON CABLE TYPE
1PR22OS, 12C16/3V
12C18/3V
S3-1 AND
S-10 AND
S-9 AND
TWELVE PIN MALE RECEPTACLE, BURNDY TYPE "TRIM
TRIO" CAT.NO. GOB1492PNE, SLAC S/N59-299-406-06.
FOR #16-20 WIRE, USE BURNDY CONTACT RC16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1
AND STOP SL-39 ONLY.
FOR #20-22 WIRE, USE BURNDY CONTACT RC20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10
AND STOP SL-40 ONLY.
FOR #24-26 WIRE, USE BURNDY CONTACT RC24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
12C18OS
164
TERM
TERMINATION DESCRIPTION
TT12S
TWELVE PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO.G6F-14-92-SNE,
SLAC S/N59-299-206-06.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
6PR22OS, 7C18TC,
1PR20OS, 12C16/3V
TT12SR
TWELVE PIN FEMALE RECEPTACLE, BURNDY TYPE "TRIM
TRIO" CAT" GOB1492SNE, SLAC S/N59-299-406-05.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
12C18OS
8/8/2011
APPLICATION
USED ON CABLE TYPE
165
TERM
TERMINATION DESCRIPTION
TT19P
NINETEEN PIN MALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO. G6F-16-19-PNE,
SLAC S/N59-299-206-07.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
1PR22OS,19C18/3V,
12C16T3V
TT19PR
NINETEEN PIN MALE RECEPTACLE, BURNDY TYPE "TRIM
TRIO" CAT. NO. GOB1619PNE,SLAC S/N59-299-406-07.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
12C18OS
8/8/2011
APPLICATION
USED ON CABLE TYPE
166
TERM
TERMINATION DESCRIPTION
TT19S
NINETEEN PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO., G6F-16-19-SNE,
SLAC S/N59-299-206-08.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
TT19SR
NINETEEN PIN FEMALE RECEPTACLE, BURNDY TYPE "TRIM
TRIO" CAT. NO. GOB1619SNE,SLAC S/N59-299-406-08.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
8/8/2011
APPLICATION
USED ON CABLE TYPE
12C18OS,11PR22OS,
19C16T3V,19C18T3V,
12C18T3V
167
TERM
TERMINATION DESCRIPTION
TT22P
TWENTY-TWO PIN MALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO. G6F-18-22-PNE, SLAC S/N59-299-206-09.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
TT22S
TWENTY-TWO PIN FEMALE CONNECTOR, BURNDY TYPE
"TRIM TRIO", CAT. NO. G6F-18-22-SNE, SLAC
S/N59-299-206-10.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
8/8/2011
APPLICATION
USED ON CABLE TYPE
168
TERM
TERMINATION DESCRIPTION
TT30P
THIRTY PIN MALE CONNECTOR, BURNDY TYPE
TRIO", CAT. NO. G6F-20-30-PNE,
SLAC S/N59-299-801-11.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N 59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE
STOP SL-40 ONLY.
TT30S
8/8/2011
APPLICATION
USED ON CABLE TYPE
"TRIM
S3-1 AND
S-10 AND
S-9 AND
THIRTY PIN FEMALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO. G6F-20-30-SNE,
SLAC S/N59-299-206-12.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
15PR22OS
169
TERM
TERMINATION DESCRIPTION
TT38P
THIRTY-EIGHT PIN MALE CONNECTOR, BURNDY TYPE "TRIM
TRIO", CAT. NO., G6F-22-38-PNE,
SLAC S/N 59-299-206-13.
FOR #16-20 WIRE, USE CONTACT RM16M-23,
SLAC S/N59-299-801-07.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RM20M-12,
SLAC S/N59-299-801-05.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RM24M-9,
SLAC S/N59-299-801-12.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
TT38S
THIRTY-EIGHT PIN FEMALE CONNECTOR, BURNDY TYPE
"TRIM TRIO", CAT. NO. G6F-22-38-SNE,
SLAC S/N59-299-206-14.
FOR #16-20 WIRE, USE CONTACT RC16M-23,
SLAC S/N 59-299-801-08.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S3-1 AND
STOP SL-39 ONLY.
FOR #20-22 WIRE, USE CONTACT RC20M-12,
SLAC S/N59-299-801-06.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-10 AND
STOP SL-40 ONLY.
FOR #24-26 WIRE, USE CONTACT RC24M-9,
SLAC S/N59-299-801-11.
USE HAND CRIMPING TOOL M10S-1 WITH DIE S-9 AND
STOP SL-40 ONLY.
TX22
TWINAX CONNECTOR, CABLE PLUG. KINGS CAT.
NO. KU-59-18, SLAC S/N. 59-299-026-01. USE KINGS
CRIMPING TOOL KTH-1000 WITH DIE KTH-2004 AND TRIM
CODE 601. INSURE PIN-# TO PIN-# CONTINUITY.
TX227241
TWINAX CONNECTOR, CABLE PLUG, 2 CONDUCTOR,
TYCO CAT# 227241-1.
TX108
TWINAX CONNECTOR, CABLE PLUG, 2 CONDUCTOR, POMONA
CAT #4957
8/8/2011
APPLICATION
USED ON CABLE TYPE
INJECTION
TOROIDS
RG22
TWC9207N
SDR PULSE
KICKER
RG108A
BELDEN 9272
170
TERM
TERMINATION DESCRIPTION
APPLICATION
USED ON CABLE TYPE
TXBJ22
TWINAX CONNECTOR, BULKHEAD JACK, KINGS
CAT. #KU-19-06, SLAC S/N59-299-026-02. USE KINGS
CRIMPING TOOL KTH-1000 WITH DIE. KTH-2004 AND TRIM
CODE 601. INSURE PIN-# TO PIN-# CONTINUITY.
FFTB BCS
RG22
UNIQ-Y
SLAC MADE POWER CABLE TO FEED AN UNIQ UP 900-CL CAMERA
AND A EDT RCX CAMERALINK TO FIBER CONVERTER.
DETAILS FOR THE UNIQ-Y CONNECTIONS ARE SHOWN
IN DRAWING CA-261-801-30.
USER
SPECIAL EXPERIMENTAL ONLY CONNECTOR, USER TO
TERMINATE AND CONNECT. MAY BE OF VARIOUS MISC.
SPECIAL TYPES. THIS DESIGNATION IS NEVER TO BE USED
FOR OPERATIONAL FACILITY MAINTAINED SYSTEMS.
USBAP
CONNECTOR, 4 PIN, USB TYPE-A, PLUG, WIRE RANGE 20-28 AWG,
KYCON P/N: KUSBX-AP-KIT-SC. NO INSULATION BOOT.
USBBP
CONNECTOR, 4 PIN, USB TYPE-B, PLUG, WIRE RANGE 20-28 AWG,
KYCON P/N: KUSBX-BP-KIT-SC.NO INSULATION BOOT.
UVC90
NINETY PIN MALE CONNECTOR. THIS CONNECTOR IS SUPPLIED
WITH UNIT. MFR. UNIVERSAL VOLTRONICS CORP.
VAT3S
CONNECTOR, FEMALE, 3 PIN CABLE RECEPTACLE,
VAT P/N N-E506-007. CONTACT/ORDER INFORMATION: VAT AG,
(925) 944-3570. CABLE ASSEMBLY PART NUMBER: 770CS-99L(X)
(X IS LENGTH IN METERS). THE CONNECTOR(S) WILL BE
SUPPLIED BY THE VENDOR ALREADY ATTACHED TO THE CABLE.
VAT7S
SEVEN PIN CONNECTOR SUPPLIED WITH ISOLATION VALVE.
IRMA FRANZ BINDER P/N 696-299-0234-00-07, ORDER FROM
VAT, WIRE IN SEQUENCE USING COLOR CODE 1R ONLY, CUT
OFF UNUSED WIRES.
VAT12P
CONNECTOR, MALE, 12 PIN CABLE PLUG, VAT P/N 81173-R1.
CONTACT/ORDER INFORMATION: VAT AG, (925) 944-3570.
CABLE ASSEMBLY PART NUMBER: 770CV-89L(X) (X IS LENGTH IN
METERS).THE CONNECTOR(S) WILL BE SUPPLIED BY THE VENDOR
ALREADY ATTACHED TO THE CABLE.
VAT12S
CONNECTOR, FEMALE, 12 PIN CABLE RECEPTACLE, VAT
P/N 81167-R1, SOCKET CONTACTS P/N RC16M23K, INTERNET
ADDRESS WWW.VAT DR. #125-902, FAST SHUTTER SYSTEM.
8/8/2011
MISC
CID HV CNTLR.
18PR22OS
VAC.VALVES
5PR20OS,9C18J
171
TERM
TERMINATION DESCRIPTION
VGAUGE
SPECIAL PREWIRED ION-GAUGE CONNECTOR.
IG-CABLE
VG-CON
SPECIAL PREWIRED FOUR PIN (IG22) AND BNC
CONNECTORS FOR CONNECTION OF AN ION-GAUGE TO A VACUUM
GAUGE LONG-LINE ADAPTOR DROP-BOX.
IG-CABLE
VIK-44
FORTY-FOUR PIN CONNECTOR, PCB EDGEON TYPE, VIKING P/N
2VH22/1AN5, SLAC S/N59-299-302-02. USE VIKING HOOD P/N
036-0121-002, SLAC S/N 93-299-300-02. SOLDER CONNECTIONS.
19PR22IS
WNB
WIRE NUT, BLUE, SIZE 12-6, WITH INNER CONDUCTING
TAPERED SPRING.
WNG
WIRE NUT, GRAY, SIZE 14-8, WITH INNER CONDUCTING
TAPERED SPRING.
WNR
WIRE NUT, RED, SIZE 16-10, WITH INNER CONDUCTING
TAPERED SPRING.
WNY
WIRE-NUT, YELLOW, SIZE 12-18, WITH INNER CONDUCTING
TAPERED SPRING.
MISC.
W1
COPPER/CONSTANTAN WIRE PAIRS. STRIP THE INSULATION
AND PUT THE COPPER CONDUCTOR (BLUE INSULATION) OF
THE FIRST PAIR UNDER THE '+' SCREW OF THE INDICATED
STARTING CHANNEL, AND THE CONSTANTAN CONDUCTOR
(RED INSULATION) UNDER THE '-' SCREW. CONTINUE
CONNECTING THE THERMOCOUPLE PAIRS IN THE SAME MANNER,
UP THROUGH THE LAST INDICATED PAIR AND/OR CHANNEL.
RF CAVITY
THERMOCOUPLES
XLR3P
MALE THREE PIN AUDIO CONNECTOR, CANNON XLR-3-12C,
SLAC S/N59-299-415-07. SOLDER CONNECTIONS.
1PR16AS, 1PR16T3V
XLR3S
FEMALE THREE PIN AUDIO CONNECTOR, CANNON AXR-3-11R,
SLAC S/N59-299-415-03. SOLDER CONNECTIONS.
1PR16T3V
8/8/2011
APPLICATION
USED ON CABLE TYPE
10PRTHRM, 1PR28CC
172
Table 4 - Trim Codes for Coaxial Cable Terminations
CROSS-REFERENCED LIST OF COAXIAL CABLE TERMINATION PROCEDURES
TERM
NO.
CABLE
TYPE
N11
RG11
ALTERNATE
CONNECTOR
PART #'S.
CRIMPING
TOOL DIE
NO.
TRIM
CODE
JACKET
TRIM JIG
KINGS
PEP*
DIELECTRIC
TRIM JIG
KINGS
PEP**
KN-59-67
KN-59-132
KN-59-201
KN-59-202
KTH-2003
402M
KTJ-60
KTJ-60P
KTD-28
KTD-28P
KTH-2004
480
KTJ-137
KTJ-60P
KTD-138
KTD-138P
TX22
RG22
KU-59-18
KTH-2004
601
23
---
---
---
BNC58
RG58
KC-59-290
KTH-2001
401
KTJ-57
KTJ-57P
KTD-25
KTD-25P
KINGS 1065-1
KTH-2001
474
KTJ-86
KTJ-57P
KTD-128
---
KINGS 1065-2
KTH-2001$
419
KTJ-71
KTJ-57P
KTD-68
KTD-68P
KC-59-291
HV58
RG58
SHV58
RG58R
KINGS 1705-2
KTH-2061
441
KTJ-72
KTJ-57P
KTD-136
KTD-136P
TNC58
RG58
KA-59-44
KTH-2001
401
KTJ-57
KTJ-57P
KTD-25
KTD-25P
KINGS 1065-2
KTH-2001
419
KTJ-71
KTJ-57P
KTD-68
KTD-68P
REYNOLDS 167-3554
KTH-2001$
REY1
---
KTJ-57P
---
---
KC-59-293
KTH-2002A
401
KTJ-57
KTJ-57P
KTD-26
KTD-26P
KTH-2062
441
KTJ-72
KTJ-57P
KTD-134
KA-59-103
HV-C
BNC59
LASL C
RG59
KC-59-294
SHV59J
RG59R
KINGS 1702-1
SHV59P
RG59R
KINGS 1705-1
KTH-2062
418
KTJ-72
KTJ-57P
KTD-136
KTD-136P
BNC62
RG62
KC-59-293
KTH2002A
401
KTJ-57
KTJ-57P
KTD-26
KTD-26P
KC-59-294
8/8/2011
173
N213
RG213
KN-59-67
KTH-2003
402M
KTJ-60
KTJ-60P
KTD-28
KTD-28P
KTH-2004
480
KTJ-137
KTJ-60P
KTD-138
KTD-138P
KINGS 1765-1
KTH-2078
475
KTJ-124
---
KTD-179
---
REYNOLDS 167-3516
KTH-2003$
REY2
---
KTJ-60P
---
KTD-REY2
KN-59-68
KTH-2004
402M
KTJ-60
KTJ-60P
KTD-28
KTD-28P
KTH-2001
401
KTJ-57
KTJ-57P
KTD-25
KTD-25P
KTH-2001
401
KTJ-57
KTJ-57P
KTD-25
KTD-25P
KN-59-132
KN-59-201
KN-59-202
HV213
N214
RG213R
RG214
KN-59-104
KN-59-105
BNC223
RG223
KC-59-80
KC-59-162
TNC223
RG223
KA-59-45
KA-59-87
$ THE CENTER CONDUCTOR PIN MUST BE SOLDERED, NOT CRIMPED. * AND ** SEE NOTES UNDER TRIM CODE CHART ON NEXT PAGE.
8/8/2011
174
CROSS-REFERENCED LIST OF COAXIAL CABLE TERMINATION PROCEDURES (continued)
TRIM CODE CHART
SEE KINGS 'K-GRIP'CATALOG FOR DETAILS OF 'A', 'B', 'C' AND 'D' DIMENSIONS.
PEP *
JACKET
TRIM JIG
PEP **
DIELECTRIC
TRIM JIG
CODE
A + B
A
B
C
D
209A
13/16" (0.81)
19/32"
7/32"
(0.43")
5/32"
401
37/64"
(0.58")
23/64"
7/32"
15/32"
(0.47")
7/64"
KTJ-57P
KTD-25P,26P
402M
19/32"
(0.59")
5/16"
9/32"
3/8"
(0.38")
7/32"
KTJ-60P
KTD-28P
415M
1 5/32"
(1.16")
15/32"
7/32"
17/32"
(0.53")
5/32"
KTJ-65
KTD-38
418
59/64"
(0.92")
45/64"
7/32"
13/16"
(0.80")
7/64"
KTJ-57P
KTD-136P
419
1 3/32"
(1.09")
7/8"
7/32"
63/64"
(0.98")
7/64"
KTJ-57P
KTD-68P
432
31/64"
(0.48")
17/64"
7/32"
(0.39")
3/32"
KTJ-78
KTD-116
441
15/16"
(0.94")
23/32"
7/32"
49/64"
(0.77")
5/32"
KTJ-57P
KTD-136P
465
19/32"
(0.59")
1/4"
11/32"
7/16"
(0.43")
5/32"
KTJ-
KTD-
474
1 1/8"
(1.13")
29/32"
7/32"
57/64"
(0.89")
15/64"
KTJ-57P
KTD-128P
475
1 15/16"
(1.94")
1 23/32"
7/32"
1 5/8"
(1.63")
5/16"
KTJ-124
KTD-179
480
11/16"
(0.69")
9/32"
13/32"
1/2"
(0.50")
3/16"
KTJ-60P
KTD-138P
601
2 1/4"
2"
1/4"
1/16"
5/32"
KTJ-23
---
8/8/2011
E: 5/32"
175
(2.25")
(0.06")
REY1
1 3/16"
(1.19")
0.76"
0.43"
1" (1.00")
3/16"
---
---
REY2
1 13/16"
(1.81")
1 23/64"
29/64"
(1.54")
17/64"
KTJ-REY2
KTD-REY2
* THE TYPES WITH A "P" SUFFIX ARE MODIFIED
KINGS JIGS THAT REDUCE THE NUMBER OF DIFFERENT
TYPES OF JIGS NEEDED. THESE JIGS HAVE EXTRA SLOTS
FOR DIFFERENT BLADE SPACINGS AND A HOLE IN THE END,
SO THAT THE DIELECTRIC AND THE CENTER CONDUCTOR
CAN BE LEFT LONG FOR TRIMMING WITH THE DIELECTRIC
TRIM JIG.
** THE TYPES WITH A "P" SUFFIX ARE MODIFIED
KINGS JIGS THAT DUE TO THE MODIFICATION ALLOW
TRIMMING OF THE CENTER CONDUCTOR AND MAKE THE
CUTTING OF THE CABLE DIELECTRIC EASIER AND
CLEANER.
8/8/2011
176
Table 5 - Revision notes for this document.
a. 85-01-25: Original issue for review and bid package (preliminary,rev X).
b. 85-01-31: Second issue (still preliminary, rev. X)
1. The TERMINATION codes in Section 2 were changed from alpha
to numeric characters, to avoid confusion with the subcontractor action
codes.
2. Some minor editing and spelling changes were also made at this time.
3. Some connector and cable descriptions have been added.
c. 85-05-29: Third issue (still preliminary, rev. X)
1. Additional editing has been done, additional descriptions added.
2. Some crimp tooling additions and corrections were made.
d. 85-06-07: First formal (-R0) release.
e. 86-03-05: Second formal (-R1) release.
1. Added 'KAnn' and 'KMnn' to Cable Installation Schedule Format Description
under 'ORIGIN / LOCATION'.
2. Added 'PINK' and 'TAN' to Table 1.
Added additional wire color code tables: 1L, 1M, 1N, 1P, 1Q, 1R, 1S, 1T and 1U.
Corrected color code in Table 1R.
3. Added MCM series definitions, and single wire estimating diameters to the beginning
of Table 2.
Corrected the SLAC S/N for MS6PSB (from -01 (error), to -51).
Changed the description for 2C16OS to show the same as 1PR16OS.
Corrected the O.D and Belden Cat No. for 2PR22OS.
Changed the description for 4PR16OS to include additional details.
Corrected the O.D. and added Alpha Cat. No. to 8C16/3V.
Corrected the voltage rating for 8C18OS.
Added Alpha No. and Color Code to 8PR16TS.
Corrected the O.D. and Belden Cat. No. for 18PR22OS.
Added additional termination information to 18PR22OS.
Added 'OVERALL SHIELD' to description for 27C20OS.
Added 'TRAY CABLE' to description for 27PR22OS.
Changed description for 50C16TC to show the same as 50C16/3V.
Added description to HVSPEC1.
Corrected Color Code on 6PR24IS.
Corrected Slac No. and MFG. on 18PR22OS.
8/8/2011
177
Added additional cable types to Table 2: 1/2HELGF, #2-FLEX,
1PR16AS, 1PR20OS, 1PR28CC, 2C8TYR, 2C10TYR, 2C12TYR, 2C14TYR,
2C16/3V, 2C16OS, 2C16T6V, 2C18TC, 2C20OS, 2PR20IS, 2PR22OS, 3C16/3V,
3C16FLX, 3C16TYR, 3C20/3V, 3PR22OS, 4C8SHLD, 4C8TYR, 4C10TYR,
4C12OJ, 4C16TYR, 4C12TYR, 4C16FLX, 4C16OS, 4PR16IS, 4PR16TC, 4PR18TC,
5C16/6V, 5C18TC, 5PR20OS, 6C16OS, 6C18TC, 6PR22OS, 6PR24IS, 7C18TC,
8C12T6V, 8C16/3V, 8C18OS, 8PR16OS, 8PR20IS, 11PR22OS, 12C10TYR,
12C12/3V, 12C16/6V, 12C12TYR, 12C18OS, 12C18TC, 12PR16AS, 12PR22OS,
15PR22OS, 15PR22TS, 18PR22OS, 19C12/6V, 19C16/3V, 24PR16TC, 26C16/3V,
27C20OS, 50C16/3V, 50C16TC, BRBW12, HVSPEC1, IG-CABLE, RG59B
4. Added additional termination types to Table 3: ACJBX, ACP,
ACP15, ACP20, ACR, AMP24P, AMP36P, BP(-ccc), BP-01, BP-02,
CED-30, D37F, D37F-A, D37M, D37M-A, DAY-20, FIXED, GP-CON,
GP-GAU, HN214, HR13P, HR13S, HV214, IG-CP6, IPVB, the 'LB' series,
LB1-6, LB4-6, LB35-8A, LB6-3, LB6-3A, LEMO-A, LFB-E, LFR-H, LFR-J,
LFR-K, LRB-A, LRB-B, LRB#6, LRB#8, LRB#10, LRR1/4, LRR#6, LRR-A,
LR6#10, LR8-6, LR8U10, LSB#10, LSR-D, LSR-E, LSR#8, LSR#10, MS-HVS,
MS5P, MS6F, MS6M, MS6PR, MS8PA, MS8PAR, MS8PW, MS8PY, MS8SA, MS10SA,
MS11PR, MS21SW, MS26PA, MS26PG, MS26SA, MS32P, N1/2HG, N223, PP50G,
PP100G, PS50/2, RS50G, RS100G, RTDS, SOLDER, STRIP, TC-CCP, TC-CCS,
TC-JNC, TC-SLV, TCSCCP, TCSCCS, TT4P-1, TT4P-2, TT4SW, TT8F, TT8M,
TT8P, TT8PR, TT8S-A, TT12P, TT12P1, TT12S, TT19P, TT19S, TT19S1,
TT22P, TT22S, TT30P, TT30S, TT38P, TT38S, VGAUGE, VG-CON, VAT7S,
XLR3P and XLR3S.
Added model no. to HV220.
Added tool '69062' to terminations LR8#10 and LB8-2.
Changed crimping tool '69062' to '59975-1' for terminations LB4-6, LR6#10, LR8#10,
and LB8-2.
Changed 'Kings Cat. No. 1765-2' to 'Kings Cat. No. 1765-1', and added 'OR DIE KTH-1078' to
termination HV213.
Changed many termination descriptions: from, the reference to a specific color code: to, a
reference to the wire type for the color code.
Corrected the description for LFB-D to remove the erroneous call-out for 'no connection'
to point 48.
Corrected the description for LFY-B to include wiring for color code 1B.
Corrected the SLAC P/N for SHV59J.
Changed LR4-3/8 to LB4-6.
Changed LR8-1/4 to LB8-2.
Added crimping, tooling and trim codes to SMA223 and SMR223.
5. Added Trim Code 432.
8/8/2011
178
f. 87-01-15: Third Formal (-R2) Release.
1. Added additional wire color code tables: 1V.
Added additonal cable types to Table 2: 1/4"HEL, 3/8"HEL, 3C14FLX, 5C16T6V,
12C20J and 19C16/6V.
2. Added additional termination types to Table 3: AMP48P, LEMO, N1/4HP and N3/8HP.
Corrected and expanded the descriptions for D37F and D37M.
g. : WORKING VERSION (RX2) NOT RELEASED.
1. Added additional wire color code tables: 1W
Added additonal cable types to Table 2: 7C22OS.
2. Added additional termination types to Table 3: TT4P
Added additional termination types: DAY-50 & MS3S-S.
3. Added addition cable type to Table 1P: 12PR22OS.
4. Added O.D and Belden Cat. #8312 to 12PR22OS.
5. Added additional cable types to Table 2: 25PR24IS, 51PR220S, RG11A, RG108A.
Added additional termination types to Table 3: D50F, TT12S,LFR-L, USER.
Corrected RG11 to RG11TRI.
Added additional wire color code table: 1X
6. Added additional cable types to Table 2: 4PR24IS, 12C18/3V
8/8/2011
179
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising