BIDS MUST BE SEALED AND ADDRESSED TO: State of Wisconsin DOA-3070 (R08/2003)

BIDS MUST BE SEALED AND ADDRESSED TO: State of Wisconsin DOA-3070 (R08/2003)
State of Wisconsin
Wis. Statutes s.16.75
DOA-3070 (R08/2003)
BIDS MUST BE SEALED AND ADDRESSED TO:
AGENCY ADDRESS:
Remove from bidder list for this commodity/service. (Return this page only.)
Bid envelope must be sealed and plainly marked in lower corner with due date and Request for Bid
# RH-1034. Late bids will be rejected. Bids MUST be date and time stamped by the soliciting
purchasing office on or before the date and time that the bid is due. Bids dated and time stamped
in another office will be rejected. Receipt of a bid by the mail system does not constitute receipt of
a bid by the purchasing office. Any bid which is inadvertently opened as a result of not being
properly and clearly marked is subject to rejection. Bids must be submitted separately, i.e., not
included with sample packages or other bids. Bid openings are public unless otherwise specified.
Records will be available for public inspection after issuance of the notice of intent to award or the
award of the contract. Bidder should contact person named below for an appointment to view the
bid record. Bids shall be firm for acceptance for sixty (60) days from date of bid opening, unless
otherwise noted. The attached terms and conditions apply to any subsequent award.
UNIVERSITY OF WISCONSIN OSHKOSH
CAMPUS SERVICES CENTER
PLANNING & CONSTRUCTION
ATTENTION: RAMONA HOLDREN
650 WITZEL AVENUE
OSHKOSH, WI 54902
REQUEST FOR BID
Bids MUST be in this office no later than
THIS IS NOT AN ORDER
BIDDER (Name and Address)
March 28, 2011 12:00 pm
Name (Contact for further information)
Ramona Holdren
Phone
Date
920-424-2006
March 15, 2011
Quote Price and Delivery FOB
FOB DESTINATION FREIGHT PREPAID AND INSTALLED
Fax bids are accepted
Item
No.
1
Quantity
and Unit
1 EACH
Fax bids are not accepted
Price
Per Unit
Description
Total
FURNISH AND INSTALL ONE FLIGHT TYPE DISH MACHINE
FOR UNIVERSITY DINING SERVICES AT THE UNIVERSITY
OF WISCONSIN OSHKOSH PER SPECIFICATIONS,
CONDITIONS OF BID AND ATTACHED PRICE SHEET.
EQUIPMENT COST
TRADE IN ALLOWANCE
TOTAL
DELIVERY DATE: _____________________________
MANUFACTURER’S AUTHORIZED SERVICE DEALER &
LOCATION: ___________________________________
BIDDING MODEL:_______________________________
BIDDING MANUFACTURER:______________________
(INCLUDE SPECS AND BROCHURES)
Payment Terms
Delivery Time / Installation Date
We claim minority bidder preference [Wis. Stats. s. 16.75(3m)]. Under Wisconsin Statutes, a 5% preference may be granted to CERTIFIED Minority Business Enterprises. Bidder must be
certified by the Wisconsin Department of Commerce. If you have questions concerning the certification process, contact the Wisconsin Department of Commerce, 5th Floor, 201 W. Washington
Ave., Madison, Wisconsin 53702, (608) 267-9550. Does Not Apply to Printing Bids.
We are a work center certified under Wis. Stats. s. 16.752 employing persons with severe disabilities. Questions concerning the certification process should be addressed to the Work Center
Program, State Bureau of Procurement, 6th Floor, 101 E. Wilson St., Madison, Wisconsin 53702, (608) 266-2605.
Wis. Stats. s. 16.754 directs the state to purchase materials which are manufactured to the greatest extent in the United States when all other factors are substantially equal. Materials covered in
our bid were manufactured in whole or in substantial part within the United States, or the majority of the component parts thereof were manufactured in whole or in substantial part in the United
States.
Yes
No
Unknown
In signing this bid we also certify that we have not, either directly or indirectly, entered into any agreement or participated in any collusion or otherwise taken any action in restraint of free
competition; that no attempt has been made to induce any other person or firm to submit or not to submit a bid; that this bid has been independently arrived at without collusion with any other bidder,
competitor or potential competitor; that this bid has not been knowingly disclosed prior to the opening of bids to any other bidder or competitor; that the above statement is accurate under penalty of
perjury.
We will comply with all terms, conditions and specifications required by the state in this Request for Bid and all terms of our bid.
Name of Authorized Company Representative (Type or Print)
Title
Signature of Above
Date
Phone
(
)
Fax
(
)
e-mail.
This form can be made available in accessible formats upon request to qualified individuals with disabilities
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
GENERAL INFORMATION:
The University of Wisconsin Oshkosh is accepting bids for the purchase and installation of one flight type dish
machine. Equipment shall be furnished in accordance with the specifications and provisions as stated in this
Request for Bid.
The specific products listed are found to meet our requirements for function, quality and durability. The
University of Wisconsin Oshkosh will be solely responsible for determining equivalency of alternate products.
PROJECT SCOPE:
General
Furnish and install a flight type dish machine for the University Dining Services in Blackhawk Commons.
Products:
See Specifications for equipment. Specific manufacturer and model numbers are provided to establish the
design, type of construction, quality, functional capability and performance level desired.
Delivery:
See Special Conditions of Bid for installation information.
Start-Up:
Bidder shall be a factory authorized dealer upon installation of equipment.
Training:
Bidder shall provide complete training on the use and maintenance of the equipment they are bidding.
Training date shall be scheduled at time of award. All costs associated with training to be included in the
bid. For the 1st year, the bidder must provide follow up training, if requested, at no additional charge
Manuals:
Bidder is to provide, free of charge, a minimum of 3 complete operators, parts and service manuals along
with instructional and repair manuals for the equipment. Manuals are to be provided to the University at
least 1 week prior to training.
Service:
All service must be provided by a manufacturer’s authorized service dealer and all replacement parts
installed under warranty to be original equipment products.
Bidder must have a manufacturer’s authorized service dealer within 200 miles of Oshkosh, WI. All
warranty service calls are to be responded to, on-site, within 24 hours. On-site service is to include
transportation and insurance costs.
Warranty:
Bidder must provide, at a minimum 1 year, or the manufacturer’s standard warranty, whichever is longer,
on items purchased under this contract. Warranty must include all costs for parts, labor, travel expenses,
etc. associated with warranty work.
Provide one extra 12 month warranty immediately following the standard warranty. Warranty must include
equipment to be free from defects in quality and workmanship for at least one year from date of start-up.
Telephone support from the factory shall be free for the life of the equipment using on –board diagnostics
and simple-to-operate systems for troubleshooting and repair.
Indicate the warranty term on the attached equipment price and warranty sheet and enclose standard
warranty documents with your bid.
Warranty for all labor and travel for service shall be covered under the manufacture’s standard warranty.
All service during the standard warranty will be performed at the University at no expense to the
University. BIDS MUST INCLUDE WARRANTY INFORMATION ON ALL PARTS OF EQUIPMENT.
Wisconsin Department of Administration
Chs. 16, 19, 51
DOA-3054 (R10/2005)
Page 1 of 4
Standard Terms And Conditions
(Request for Bids / Proposals)
1.0
SPECIFICATIONS: The specifications in this request are the minimum acceptable. When specific manufacturer and model
numbers are used, they are to establish a design, type of construction, quality, functional capability and/or performance level
desired. When alternates are bid/proposed, they must be identified by manufacturer, stock number, and such other information
necessary to establish equivalency. The State of Wisconsin shall be the sole judge of equivalency. Bidders/proposers are
cautioned to avoid bidding alternates to the specifications which may result in rejection of their bid/proposal.
2.0
DEVIATIONS AND EXCEPTIONS: Deviations and exceptions from original text, terms, conditions, or specifications shall be
described fully, on the bidder's/proposer's letterhead, signed, and attached to the request. In the absence of such statement, the
bid/proposal shall be accepted as in strict compliance with all terms, conditions, and specifications and the bidders/proposers shall
be held liable.
3.0
QUALITY: Unless otherwise indicated in the request, all material shall be first quality. Items which are used, demonstrators,
obsolete, seconds, or which have been discontinued are unacceptable without prior written approval by the State of Wisconsin.
4.0
QUANTITIES: The quantities shown on this request are based on estimated needs. The state reserves the right to increase or
decrease quantities to meet actual needs.
5.0
DELIVERY: Deliveries shall be F.O.B. destination freight prepaid and included unless otherwise specified.
6.0
PRICING AND DISCOUNT: The State of Wisconsin qualifies for governmental discounts and its educational institutions also qualify
for educational discounts. Unit prices shall reflect these discounts.
6.1 Unit prices shown on the bid/proposal or contract shall be the price per unit of sale (e.g., gal., cs., doz., ea.) as stated on the
request or contract. For any given item, the quantity multiplied by the unit price shall establish the extended price, the unit
price shall govern in the bid/proposal evaluation and contract administration.
6.2 Prices established in continuing agreements and term contracts may be lowered due to general market conditions, but prices
shall not be subject to increase for ninety (90) calendar days from the date of award. Any increase proposed shall be
submitted to the contracting agency thirty (30) calendar days before the proposed effective date of the price increase, and
shall be limited to fully documented cost increases to the contractor which are demonstrated to be industry wide. The
conditions under which price increases may be granted shall be expressed in bid/proposal documents and contracts
or
agreements.
6.3 In determination of award, discounts for early payment will only be considered when all other conditions are equal and when
payment terms allow at least fifteen (15) days, providing the discount terms are deemed favorable. All payment terms must
allow the option of net thirty (30).
7.0
UNFAIR SALES ACT: Prices quoted to the State of Wisconsin are not governed by the Unfair Sales Act.
8.0
ACCEPTANCE-REJECTION: The State of Wisconsin reserves the right to accept or reject any or all bids/proposals, to waive any
technicality in any bid/proposal submitted, and to accept any part of a bid/proposal as deemed to be in the best interests of the
State of Wisconsin.
Bids/proposals MUST be date and time stamped by the soliciting purchasing office on or before the date and time that the
bid/proposal is due. Bids/proposals date and time stamped in another office will be rejected. Receipt of a bid/proposal by the mail
system does not constitute receipt of a bid/proposal by the purchasing office.
9.0
METHOD OF AWARD: Award shall be made to the lowest responsible, responsive bidder unless otherwise specified.
10.0
ORDERING: Purchase orders or releases via purchasing cards shall be placed directly to the contractor by an authorized agency.
No other purchase orders are authorized.
11.0
PAYMENT TERMS AND INVOICING: The State of Wisconsin normally will pay properly submitted vendor invoices within thirty
(30) days of receipt providing goods and/or services have been delivered, installed (if required), and accepted as specified.
Invoices presented for payment must be submitted in accordance with instructions contained on the purchase order including
reference to purchase order number and submittal to the correct address for processing.
A good faith dispute creates an exception to prompt payment.
12.0
TAXES: The State of Wisconsin and its agencies are exempt from payment of all federal tax and Wisconsin state and local taxes
on its purchases except Wisconsin excise taxes as described below.
The State of Wisconsin, including all its agencies, is required to pay the Wisconsin excise or occupation tax on its purchase of beer,
liquor, wine, cigarettes, tobacco products, motor vehicle fuel and general aviation fuel. However, it is exempt from payment of
Wisconsin sales or use tax on its purchases. The State of Wisconsin may be subject to other states' taxes on its purchases in that
state depending on the laws of that state. Contractors performing construction activities are required to pay state use tax on the
cost of materials.
13.0
GUARANTEED DELIVERY: Failure of the contractor to adhere to delivery schedules as specified or to promptly replace rejected
materials shall render the contractor liable for all costs in excess of the contract price when alternate procurement is necessary.
Excess costs shall include the administrative costs.
14.0
ENTIRE AGREEMENT: These Standard Terms and Conditions shall apply to any contract or order awarded as a result of this
request except where special requirements are stated elsewhere in the request; in such cases, the special requirements shall
apply. Further, the written contract and/or order with referenced parts and attachments shall constitute the entire agreement and no
other terms and conditions in any document, acceptance, or acknowledgment shall be effective or binding unless expressly agreed
to in writing by the contracting authority.
15.0
APPLICABLE LAW AND COMPLIANCE: This contract shall be governed under the laws of the State of Wisconsin. The
contractor shall at all times comply with and observe all federal and state laws, local laws, ordinances, and regulations which are in
effect during the period of this contract and which in any manner affect the work or its conduct. The State of Wisconsin reserves
the right to cancel this contract if the contractor fails to follow the requirements of s. 77.66, Wis. Stats., and related statutes
regarding certification for collection of sales and use tax. The State of Wisconsin also reserves the right to cancel this contract with
any federally debarred contractor or a contractor that is presently identified on the list of parties excluded from federal procurement
and non-procurement contracts.
16.0
ANTITRUST ASSIGNMENT: The contractor and the State of Wisconsin recognize that in actual economic practice, overcharges
resulting from antitrust violations are in fact usually borne by the State of Wisconsin (purchaser). Therefore, the contractor hereby
assigns to the State of Wisconsin any and all claims for such overcharges as to goods, materials or services purchased in
connection with this contract.
17.0
ASSIGNMENT: No right or duty in whole or in part of the contractor under this contract may be assigned or delegated without the
prior written consent of the State of Wisconsin.
18.0
WORK CENTER CRITERIA: A work center must be certified under s. 16.752, Wis. Stats., and must ensure that when engaged in
the production of materials, supplies or equipment or the performance of contractual services, not less than seventy-five percent
(75%) of the total hours of direct labor are performed by severely handicapped individuals.
19.0
NONDISCRIMINATION / AFFIRMATIVE ACTION: In connection with the performance of work under this contract, the contractor
agrees not to discriminate against any employee or applicant for employment because of age, race, religion, color, handicap, sex,
physical condition, developmental disability as defined in s. 51.01(5), Wis. Stats., sexual orientation as defined in s. 111.32(13m),
Wis. Stats., or national origin. This provision shall include, but not be limited to, the following: employment, upgrading, demotion or
transfer; recruitment or recruitment advertising; layoff or termination; rates of pay or other forms of compensation; and selection for
training, including apprenticeship. Except with respect to sexual orientation, the contractor further agrees to take affirmative action
to ensure equal employment opportunities.
19.1 Contracts estimated to be over twenty-five thousand dollars ($25,000) require the submission of a written affirmative action
plan by the contractor. An exemption occurs from this requirement if the contractor has a workforce of less than twenty-five
(25) employees. Within fifteen (15) working days after the contract is awarded, the contractor must submit the plan to the
contracting state agency for approval. Instructions on preparing the plan and technical assistance regarding this clause are
available from the contracting state agency.
19.2 The contractor agrees to post in conspicuous places, available for employees and applicants for employment, a notice to be
provided by the contracting state agency that sets forth the provisions of the State of Wisconsin's nondiscrimination law.
19.3 Failure to comply with the conditions of this clause may result in the contractor's becoming declared an "ineligible"
contractor, termination of the contract, or withholding of payment.
20.0
PATENT INFRINGEMENT: The contractor selling to the State of Wisconsin the articles described herein guarantees the articles
were manufactured or produced in accordance with applicable federal labor laws. Further, that the sale or use of the articles
described herein will not infringe any United States patent. The contractor covenants that it will at its own expense defend every
suit which shall be brought against the State of Wisconsin (provided that such contractor is promptly notified of such suit, and all
papers therein are delivered to it) for any alleged infringement of any patent by reason of the sale or use of such articles, and
agrees that it will pay all costs, damages, and profits recoverable in any such suit.
21.0
SAFETY REQUIREMENTS: All materials, equipment, and supplies provided to the State of Wisconsin must comply fully with all
safety requirements as set forth by the Wisconsin Administrative Code and all applicable OSHA Standards.
22.0
WARRANTY: Unless otherwise specifically stated by the bidder/proposer, equipment purchased as a result of this request shall be
warranted against defects by the bidder/proposer for one (1) year from date of receipt. The equipment manufacturer's standard
warranty shall apply as a minimum and must be honored by the contractor.
23.0
INSURANCE RESPONSIBILITY: The contractor performing services for the State of Wisconsin shall:
23.1
Maintain worker's compensation insurance as required by Wisconsin Statutes, for all employees engaged in the work.
23.2
Maintain commercial liability, bodily injury and property damage insurance against any claim(s) which might occur in
carrying out this agreement/contract. Minimum coverage shall be one million dollars ($1,000,000) liability for bodily injury
and property damage including products liability and completed operations. Provide motor vehicle insurance for all owned,
non-owned and hired vehicles that are used in carrying out this contract. Minimum coverage shall be one million dollars
($1,000,000) per occurrence combined single limit for automobile liability and property damage.
23.3
The state reserves the right to require higher or lower limits where warranted.
24.0
CANCELLATION: The State of Wisconsin reserves the right to cancel any contract in whole or in part without penalty due to
nonappropriation of funds or for failure of the contractor to comply with terms, conditions, and specifications of this contract.
25.0
VENDOR TAX DELINQUENCY: Vendors who have a delinquent Wisconsin tax liability may have their payments offset by the
State of Wisconsin.
26.0
PUBLIC RECORDS ACCESS: It is the intention of the state to maintain an open and public process in the solicitation, submission,
review, and approval of procurement activities.
Bid/proposal openings are public unless otherwise specified. Records may not be available for public inspection prior to issuance
of the notice of intent to award or the award of the contract.
27.0
28.0
PROPRIETARY INFORMATION: Any restrictions on the use of data contained within a request, must be clearly stated in the
bid/proposal itself. Proprietary information submitted in response to a request will be handled in accordance with applicable State
of Wisconsin procurement regulations and the Wisconsin public records law. Proprietary restrictions normally are not accepted.
However, when accepted, it is the vendor's responsibility to defend the determination in the event of an appeal or litigation.
27.1
Data contained in a bid/proposal, all documentation provided therein, and innovations developed as a result of the
contracted commodities or services cannot be copyrighted or patented. All data, documentation, and innovations become
the property of the State of Wisconsin.
27.2
Any material submitted by the vendor in response to this request that the vendor considers confidential and proprietary
information and which qualifies as a trade secret, as provided in s. 19.36(5), Wis. Stats., or material which can be kept
confidential under the Wisconsin public records law, must be identified on a Designation of Confidential and Proprietary
Information form (DOA-3027). Bidders/proposers may request the form if it is not part of the Request for Bid/Request for
Proposal package. Bid/proposal prices cannot be held confidential.
DISCLOSURE: If a state public official (s. 19.42, Wis. Stats.), a member of a state public official's immediate family, or any
organization in which a state public official or a member of the official's immediate family owns or controls a ten percent ( 10%)
interest, is a party to this agreement, and if this agreement involves payment of more than three thousand dollars ($3,000) within a
twelve (12) month period, this contract is voidable by the state unless appropriate disclosure is made according to s. 19.45(6), Wis.
Stats., before signing the contract. Disclosure must be made to the State of Wisconsin Ethics Board, 44 East Mifflin Street, Suite
601, Madison, Wisconsin 53703 (Telephone 608-266-8123).
State classified and former employees and certain University of Wisconsin faculty/staff are subject to separate disclosure
requirements, s. 16.417, Wis. Stats.
29.0
RECYCLED MATERIALS: The State of Wisconsin is required to purchase products incorporating recycled materials whenever
technically and economically feasible. Bidders are encouraged to bid products with recycled content which meet specifications.
30.0
MATERIAL SAFETY DATA SHEET: If any item(s) on an order(s) resulting from this award(s) is a hazardous chemical, as defined
under 29CFR 1910.1200, provide one (1) copy of a Material Safety Data Sheet for each item with the shipped container(s) and one
(1) copy with the invoice(s).
31.0
PROMOTIONAL ADVERTISING / NEWS RELEASES: Reference to or use of the State of Wisconsin, any of its departments,
agencies or other subunits, or any state official or employee for commercial promotion is prohibited. News releases pertaining to
this procurement shall not be made without prior approval of the State of Wisconsin. Release of broadcast e-mails pertaining to this
procurement shall not be made without prior written authorization of the contracting agency.
32.0
HOLD HARMLESS: The contractor will indemnify and save harmless the State of Wisconsin and all of its officers, agents and
employees from all suits, actions, or claims of any character brought for or on account of any injuries or damages received by any
persons or property resulting from the operations of the contractor, or of any of its contractors, in prosecuting work under this
agreement.
33.0
FOREIGN CORPORATION: A foreign corporation (any corporation other than a Wisconsin corporation) which becomes a party to
this Agreement is required to conform to all the requirements of Chapter 180, Wis. Stats., relating to a foreign corporation and must
possess a certificate of authority from the Wisconsin Department of Financial Institutions, unless the corporation is transacting
business in interstate commerce or is otherwise exempt from the requirement of obtaining a certificate of authority. Any foreign
corporation which desires to apply for a certificate of authority should contact the Department of Financial Institutions, Division of
Corporation, P. O. Box 7846, Madison, WI 53707-7846; telephone (608) 261-7577.
34.0
WORK CENTER PROGRAM: The successful bidder/proposer shall agree to implement processes that allow the State agencies,
including the University of Wisconsin System, to satisfy the State's obligation to purchase goods and services produced by work
centers certified under the State Use Law, s.16.752, Wis. Stat. This shall result in requiring the successful bidder/proposer to
include products provided by work centers in its catalog for State agencies and campuses or to block the sale of comparable items
to State agencies and campuses.
35.0
FORCE MAJEURE: Neither party shall be in default by reason of any failure in performance of this Agreement in accordance with
reasonable control and without fault or negligence on their part. Such causes may include, but are not restricted to, acts of nature
or the public enemy, acts of the government in either its sovereign or contractual capacity, fires, floods, epidemics, quarantine
restrictions, strikes, freight embargoes and unusually severe weather, but in every case the failure to perform such must be beyond
the reasonable control and without the fault or negligence of the party.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
SPECIAL CONDITIONS OF BID
DELIVERY:
Delivery and installation is expected to commence May 18 – 29, 2011 and to be completed August 7,
2011 or earlier. Please state if this requirement can be met. Bidders must indicate a firm installation
date on the Request for Bid form. If unable to install by the above dates, please indicate the earliest
installation date possible. Timeliness of installation may be used in award of bid. Final installation
date must be acceptable to Dining Services. At the time of award, the successful bidder will be
notified of project delivery and installation dates. SEE SPECIFICATION SHEET FOR ADDITIONAL
DELIVERY INFORMATION.
F.O.B. DESTINATION INSTALLED: FREIGHT PREPAID AND ALLOWED (vendor responsible for
freight costs.) Equipment is to be shipped, assembled and installed in the Dining Services area at the
University of Wisconsin Oshkosh, Blackhawk Commons, 725 Algoma Boulevard, Oshkosh, WI 54901.
Bid prices are to include all packing, insurance, transportation, loading and unloading, start-up and
training. Dish machine shall be set in place, assembled, leveled and operational. Bidder must
dispose of all packing materials off-site. Bid prices must include three operating and parts manuals
furnished to UW Oshkosh.
METHOD OF
BID:
Bidders shall submit a unit price per line item with a net cost total as designated on the Equipment
Price and Warranty Bid Sheet.
Complete and return the following along with brochures and specifications:
1. Request for Bid Form
2. Equipment Price and Warranty Bid Sheet
3. Vendor Reference Sheet
4. Vendor Information Sheet
5. Vendor Agreement Sheet
6. Affidavit
METHOD OF
AWARD:
Award shall be made to the lowest qualified bidder on the basis of the lowest net cost total of
equipment that is judged to be in the best interest of the University of Wisconsin Oshkosh. Other
factors in the selection of a bidder shall include life cycle costs, timeliness of delivery, warranties,
service capabilities and references.
Any allowance for trade-in value of the existing machine shall be noted in the bid.
Winning vendor must show proof that service technicians have been factory trained before the date of
installation.
ADDITIONAL
INFORMATION:
For additional information regarding this bid, please contact Kevin Shumann at 920-424-0220 or
Ramona Holdren at 920-424-2006.
Technical questions should be directed to Marty Strand at 920-424-2392.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
SPECIAL CONDITIONS OF BID CONTINUED
SPECIFICATIONS:
Specific manufacturers and model numbers are provided to establish the design, type of construction, quality,
functional capability and performance level desired. Any alternate product(s) bid must be clearly identified by
manufacturer and catalog, model or stock number. Adequate detailed specifications of the product offered must be
included with your bid to establish equivalency. A sample and demonstration of alternate low models bid will be
required. The State of Wisconsin shall be the sole judge of equivalency.
BIDDER QUALIFICATIONS:
To avoid disqualification of your bid, bidder must be qualified and able to provide the following:
Bidder must be an authorized distributor for the original manufacturer for the specified product and in the business for a
minimum of 3 years.
Bidder must submit a list of three contracts similar to this contract served within the calendar year 2010 or are in the
process of serving as of January 1, 2011. Provide agency name, address, contact name and telephone number, and
dollar volume of said contracts. SEE BIDDER REFERENCE SHEET ATTACHED.
Bidder must be able to provide on-site installation.
The Bidder shall maintain insurance levels as required in STANDARD TERMS AND CONDITIONS, SECTION 23.0. A
certificate of insurance must be provided upon request.
MANDATORY SITE VISIT:
A mandatory site visit is required prior to submitting a bid. The purpose of this visit is to assure bidders and the
University that all requirements of the project are fully understood. A site visit is to be scheduled by Marty Strand,
Assistant Director for Dining Operations, at (920) 424-2392. UW Oshkosh is not responsible for costs incurred to
attend the mandatory meeting. The bidder representative at the site visit must be an employee of bidding company.
This same bidder representative’s company must do all required set up and installation. Other representatives and
subcontractors do not meet qualifications for site visit and are not required to attend. The Contractor is responsible for
making all field measurements necessary for establishing exact locations and relationships necessary for the correct
installation of equipment.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
SPECIAL CONDITIONS OF BID CONTINUED
FAXED BIDS: All faxed bid responses must have a facsimile transmission cover letter. This letter must include:
a. Bid Due Date and Request for Bid # RH-1034
b. Current Date
c. Agency fax number (920) 424-0259
d. Agency name
e. Agency contact person and telephone number
f. Bidder fax number (if available)
g. Bidder name
h. Bidder contact person and telephone number
i. Number of pages (including cover) being transmitted.
Faxed replies to bid requests must be signed. Each page must be initialed and numbered “Page 1
of 5, page 2 of 5”, etc.
Faxed bids will be rejected if they do not arrive on time, i.e., the last page of the fax transmission must
be completed prior to the bid opening due date and time. It is the responsibility of the bidder to verify
that the faxed bid has been received and delivered to the proper purchasing office location by the bid
date and time.
MAILED BIDS: Mail bids, specifications and brochures to the following:
University of Wisconsin Oshkosh
Attention: Ramona Holdren
Campus Services
Planning & Construction
650 Witzel Avenue
Oshkosh, WI 54902
Bid envelope must be sealed and plainly marked in lower corner with bidder name and address, due
date and Request for Bid # RH-1034. Mailed bids will be rejected if they do not arrive on time.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
.
SPECIFICATIONS:
The specifications shown for the dish washer are the minimum acceptable specifications of the equipment desired. If
not bidding on all particulars as specified, the bidder may offer that equipment he believes to be an “or equal”
alternate. Any alternates bid must be clearly identified by manufacturer and model or stock number with adequate
detailed product information to establish equivalency. Failure to provide product information may result in
disqualification of your bid. The University of Wisconsin Oshkosh will be the sole judge of equivalency and
acceptability. The dish machine requirements on this Request for Bid are based on Hobart Model FT920DBD.
THE FOLLOWING SERVICES SHALL BE PROVIDED BY THE UNIVERSITY OF WISCONSIN OSHKOSH:





Disconnect existing machine from all utilities prior to work by bidder.
Provide all mechanical modifications necessary in building to accommodate new machines; i.e.: electrical,
water, drain, steam, ventilation including new duct risers, and condensate lines.
Provide final electrical service connections to new machines.
Provide final plumbing connections to new machines.
Provide final steam, ductwork and condensate line connections to new machines.
FOOD SERVICE DEALER MUST PROVIDE THE FOLLOWING SERVICES:
(Factory authorized personnel must be provided for all dish machine installation work):





Disassemble and remove existing equipment and remove from premises.
Provide factory authorized personnel to set in place and assemble dish machine in preparation for final
connections.
Perform start up and initial performance check of dish machine.
Provide on-site training for operating and maintenance personnel.
Clean area after dish machine installation and remove all debris off site.
EQUIPMENT:
DIRECTION OF OPERATION:
-
Left to Right (L-R)
MACHINE TYPE:
- Flight-Type dish machine
SIZE:
-
43 inches wide (+ ½”)
20 feet, 10 inches long in 5-8-11 foot increments
37 inches high at load and unload ends (+ ½”)
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
CONSTRUCTION:
-
Tanks and wash chambers shall be constructed of #16 gauge stainless steel heliarc welded #3 polished
outside with satin finish.
Provide four extra large hinged inspection doors of #16 gauge stainless steel with welded handle brackets.
All doors shall be insulated.
Prewash door shall have 34” opening.
Power wash and power rinse doors shall have 42” openings.
Interior shall have flat cleanable surfaces. Internal plumbing within washing chambers will not be accepted.
Conveyor tracks shall be stainless steel.
Prewash, power wash and power pumps and motors shall be integrally assembled and mounted to tanks.
Machine shall be completely enclosed with stainless steel panels.
Tanks shall be of “L” shaped design allowing 7 ½” of water above pump intake - eliminating cavitations of the
pumps.
PUMPS:
-
Prewash pump shall provide 150 gallons GPM.
Power wash and rinse pump shall provide 292 GPM each, with NI-Resist impellers, integral with motors,
assuring perfect alignment and quiet operation.
Each pump shall be provided with pack-less seals with stainless steel metal parts and ceramic sealing seats
(no stuffing box allowed).
Provide easily removable front end plates for ease of cleaning and inspection.
All pumps shall be self-draining.
MOTORS:
-
Motors shall be built for machine manufacturer with grease packed ball-bearing splash-proof design totally
enclosed and fan cooled.
Prewash, power wash, power rinse motors shall be 3 HP.
Conveyor motor drive shall be ½ HP.
All motors shall operate at 208-240 volts, 60 cycles, 3 phase.
MOTOR CONTROLS:
-
Provide vertical stainless steel control center with power “on/off” switch mounted on final rinse section.
Controls shall use 115-volt pilot circuit.
Start/Stop switches shall be mounted under plate rest at each end of machine.
Provide factory wired electrical connections direct from electrical relays in control panel to each component on
machine, no inline connections will be accepted.
All wire shall be U.L. Listed, thermoplastic insulated and rated to 105 degree C at 600V.
Provide energy saving control feature of stopping conveyor when operation of pumps and final rinse stops.
Under normal operation all pumps shall be started by a single switch.
All inspection doors in wet areas shall have safety switches to shut down power to the pumps when doors are
open.
Provide mounted circuit breakers and single point electrical connection for entire machine.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
CONVEYOR DRIVE UNIT AND SAFETY DEVICE SHALL HAVE THE FOLLOWING:
-
Powered by machine.
Manufacturer built, inherent overload ½ HP grease packed ball bearing motor.
Conveyor speed to be variable from 4 to 12 feet per minute.
Trip mechanism provided on unloading end of conveyor and to be of positive stop design with no coasting of
conveyor.
Jam protection provided by load sensing switch at drive platform.
Drive unit and safety devices shall interrupt the operation of conveyor motor, pumps, and final rinse flow.
Operation shall be re-started automatically by removing items from trip mechanism.
Reversing switch within main control panel.
VAPOR CONTROL:
-
Built-in vent connection shall be located in center of machine and shall be 16” in diameter with connection
rated at 1000 CFM.
Unit shall have integral plenum provided by manufacturer or unit.
FLIGHT CONVEYOR:
-
Provide stainless steel side links and rod fitted with injection molded resilient flight links to accommodate
flatware and trays in an inclined position.
Base of belt shall be “V” shaped design on all pegs and spacers to allow unobstructed flow of water to ware.
Overall width of conveyor shall be minimum 30 ½” with clearance between guides of 31 ½”.
RE-CIRCULATING WATER PREWASH SECTION:
-
Unit shall receive all detergent overflow water from the wash tank in addition to final rinse water.
Water from below the load conveyor extension shall be flushed into prewash scrap collector by means of recirculated prewash water pumped through stainless steel manifolds and nozzles.
Cold water used to temper prewash tank shall be thermostatically controlled.
PREWASH POWER WASH AND POWER RINSE:
-
-
Each compartment shall be equipped with stainless steel upper and lower center feed wash manifolds with
specially shaped stainless steel debossed jets, having unrestricted openings and arranged to direct streams at
angles that will reach all surfaces of tableware and trays.
Provide one-piece wash arms manifolds quickly removed without the use of tools on a draw type assembly.
Assure proper alignment and installation of all wash arms.
OVERFLOW:
-
Each compartment shall have bell-type automatic wide-mouth overflow to direct water through internal
connecting stainless steel tubing to prewash section.
Prewash overflow shall be stainless steel standpipe to allow water to flow to drain when water level rises.
Tank bottom shall be formed with drain opening 3” below side seams of tank for positive drainage.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
DRAIN AND SIDE ACCESS CLEAN OUT OPENINGS:
-
Drain valves shall be manually controlled from front of machine.
Discharge superstructures shall be supplied with two drain openings pre-plumbed to a common drain
connection.
Stainless steel side panels shall be totally removable to allow unencumbered access for cleaning at both
loading and unloading ends of the machine.
STRAINER SCREENS:
-
Prewash, wash, and rinse tanks shall be provided with large inverted one-piece removable perforated (1/8”
diameter openings) stainless steel strainer pans.
Pans shall be of sloped design to a large deep perforated (1/8” diameter openings) stainless steel bucket; both
shall be accessible from the front of the machine.
HEATING EQUIPMENT:
-
-
Power wash and power rinse tanks shall be fitted with ¾” regulated stainless steel coil tank heaters electrically
controlled by solid state thermostats mounted in NEMA 12 boxes, on/off heat switch and pilot lights located in
main control panel.
Steam pressure shall be 8-10 PSI.
Steam coils shall have a minimum surface area of 3166 square inches.
Automatic positive low water protection float shall be actuated when power switch is on.
Tank heater shall automatically turn off if tank is accidentally drained.
FINAL RINSE AND BOOSTER HEATER:
-
Provide 185-degree F water at 90 GPH via steam booster similar to Thrush model #150 mounted under clean
end of machine operating at 8-10 PSI steam.
Total final rinse water consumption shall not exceed 90 GPH at 20 PSI.
HEAT RECOVERY SYSTEM:
-
Hot and cold ground water to be directly plumbed into the final rinse water system.
Water leaving the energy recovery coil shall be thermostatically monitored.
When temperature of water leaving energy recovery coil reaches 105°F, hot water supply to final rinse system
shall shut off. This shall occur in approximately 4 minutes, leaving only a cold ground water supply for the final
rinse water system.
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
ASSEMBLY AND WARRANTY:
-
Dishwasher shall be assembled under supervision of and checked by factory authorized personal.
Entire unit shall carry UL and NSF Sanitation seals of approval.
Installation of new system shall be provided by machine manufacturer.
Provide standard full 18 month warranty against manufacturer's defects on parts, labor, and travel expenses
for personnel.
Provide one extra 12 month warranty period immediately following the standard warranty (included in net
cost.)
COMPARABLE MODEL:
HOBART FT920DBD
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
EQUIPMENT PRICE AND WARRANTY BID SHEET
ITEM
MODEL
1
2
DESCRIPTION
STANDARD
WARRANTY
TERM
FLIGHT TYPE
DISH MACHINE
QUANTITY
UNIT PRICE
1 EA
TRADE IN
ALLOWANCE FOR
HOBART MODEL
# FTM-824-5-8-11
WITH STEAM
BOOSTER & TANK
HEAT
1 LOT
*** NET COST
*** EQUIPMENT BID WILL BE AWARDED BASED ON LOWEST NET COST
BIDDER SHALL PROVIDE ONE EXTRA 12 MONTH WARRANTY PERIOD IMMEDIATELY FOLLOWING
STANDARD MANUFACTURER’S WARRANTY. INCLUDED IN COST __________ ___________
YES
NO
__________________________________________
Company Name
__________________________________________
__________________________________________
Company Representative Name and Title (Printed)
Company Representative Name (Signature)
_________________________
_________________________
______________
__________________
Company Address
City
State
Zip Code
______________________
_________________________
______________
Phone
Fax
Date
UNIVERSITY OF WISCONSIN OSHKOSH
FLIGHT TYPE DISH MACHINE
SEALED BID RH-1034
BIDDER REFERENCES
__________________________________________
BIDDER COMPANY NAME
BIDDER REFERENCES:
1.
__________________________________________
__________________________________________
Company Name
Contact Person
_________________________________________
__________________________________________
Address
City
State
Zip Code
__________________________________________
Dollar Volume of Contract
Year
2.
__________________________________________
__________________________________________
Company Name
Contact Person
_________________________________________
__________________________________________
Address
City
State
Zip Code
__________________________________________
Dollar Volume of Contract
Year
3.
__________________________________________
__________________________________________
Company Name
Contac t Person
_________________________________________
__________________________________________
Address
City
__________________________________________
Dollar Volume of Contract
Year
State
Zip Code
STATE OF WISCONSIN
Bid / Proposal #
RH-1034
DOA-3477 (R05/98)
Commodity / Service
VENDOR INFORMATION
1.
BIDDING / PROPOSING COMPANY NAME
FEIN
Phone
(
)
Toll Free Phone
FAX
(
)
E-Mail Address
(
)
Address
City
2.
State
Zip + 4
Name the person to contact for questions concerning this bid / proposal.
Name
Title
Phone
(
)
Toll Free Phone
FAX
(
)
E-Mail Address
(
)
Address
City
3.
State
Zip + 4
Any vendor awarded over $25,000 on this contract must submit affirmative action information to the
department. Please name the Personnel / Human Resource and Development or other person responsible
for affirmative action in the company to contact about this plan.
Name
Title
Phone
(
)
Toll Free Phone
FAX
(
)
E-Mail Address
(
)
Address
City
4.
State
Zip + 4
Mailing address to which state purchase orders are mailed and person the department may contact
concerning orders and billings.
Name
Title
Phone
(
)
Toll Free Phone
FAX
(
)
E-Mail Address
(
Address
City
5.
CEO / President Name
State
Zip + 4
)
Division of State Agency Services
State Bureau of Procurement
State of Wisconsin
Department of Administration
DOA-3333 (R03/2004)
Vendor Agreement
Wisconsin’s Cooperative Purchasing Service
Wisconsin statutes (s. 16.73, Wis. Stats.) establish authority to allow Wisconsin municipalities to purchase from state contracts.
Participating in the service gives vendors opportunities for additional sales without additional bidding. Municipalities use the
service to expedite purchases. A "municipality" is defined as any county, city, village, town, school district, board of school
directors, sewer district, drainage district, vocational, technical and adult education district, or any other public body having the
authority to award public contracts (s. 16.70(8), Wis. Stats.). Federally recognized Indian tribes and bands in this state may
participate in cooperative purchasing with the state or any municipality under ss. 66.0301(1) and (2), Wis.Stats.
Interested municipalities:
 will contact the contractor directly to place orders referencing the state agency contract number; and
 are responsible for receipt, acceptance, inspection of commodities directly from the contractor, and making payment directly
to the contractor.
The State of Wisconsin is not a party to these purchases or any dispute arising from these purchases and is not liable for
delivery or payment of any of these purchases.
The State of Wisconsin will determine the contractor’s participation by checking a box below.
MANDATORY: Bidders/Proposers must agree to furnish the commodities or services of this bid/proposal to Wisconsin
municipalities. Vendors should note any special conditions below.
OPTIONAL: Bidders/Proposers may or may not agree to furnish the commodities or services of this bid/proposal to
Wisconsin municipalities. A vendor’s decision on participating in this service has no effect on awarding this contract.
A vendor in the service may specify minimum order sizes by volume or dollar amount, additional charges beyond normal
delivery areas, or other minimal changes for municipalities.
Vendor: please check one of the following boxes in response.
I Agree to furnish the commodities or services of this bid/proposal to Wisconsin municipalities with any special
conditions noted below.
I Do Not Agree to furnish the commodities or services to Wisconsin municipalities.
Special Conditions (if applicable):
Signature
Date (mm/dd/ccyy)
Name (Type or Print)
Title
Company
Telephone
(
Address (Street)
Commodity/Service
City
)
State
ZIP + 4
Request for Bid/Proposal Number
RH-1034
This form can be made available in accessible formats upon request to qualified individuals with disabilities
Bid / Proposal #
State of Wisconsin
Department of Administration
RH-1034
DOA-3476 (R01/2000)
S. 16.75(3m) Wis. Stats.; s. 16.752 Wis. Stats.
Affidavit
This completed affidavit must be submitted with the bid/proposal.
Proposer Preference: Please indicate below if claiming a proposer preference.
Minority Business Preference (s. 16.75(3m), Wis. Stats.) - Must be certified by the Wisconsin
Department of Commerce. If you have questions concerning the certification process, contact
the Wisconsin Department of Commerce, 8th Floor, 123 W. Washington Ave., P.O. Box 7970,
Madison, Wisconsin 53707-7970,
(608) 267-9550.
Work Center Preference (s 16.752, Wis Stats.) - Must be certified by the State of Wisconsin Use
Board. If you have questions concerning the certification process, contact the Wisconsin State
Use Board, 101 East Wilson Street, 6th Floor, PO Box 7867, Madison, Wisconsin 53707-7867 or
608/266-2553.
American-Made Materials: The materials covered in our proposal were manufactured in whole or in substantial part within the
United States, or the majority of the component parts thereof were manufactured in whole or in substantial part in the United
States.
Yes
No
Unknown
Non-Collusion: In signing this proposal we also certify that we have not, either directly or indirectly, entered into any agreement
or participated in any collusion or otherwise taken any action in restraint of free trade; that no attempt has been made to induce
any other person or firm to submit or not to submit a proposal; that this proposal has been independently arrived at without
collusion with any other proposer competitor or potential competitor; that this proposal has not been knowingly disclosed prior to
opening of proposals to any other proposer or competitor; that the above statement is accurate under penalty of perjury.
We will comply with all terms, conditions, and specifications required by the State of Wisconsin in this Announcement of
Bid/Proposal and the terms of our bid/proposal.
Authorized Representative
Title
Type or Print
Authorized Representative
Date (mm/dd/ccyy)
Signature
Company Name
Telephone
(
)
This document can be made available in accessible formats to qualified individuals with disabilities.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement