EN
Remeha
Fuel oil/gas boilers
P 320
Installation and
Service Manual
300016243-001-D
63184
Declaration of conformity 1
C001879-B
The appliance complies with the standard model described in
declaration of compliance 1. It is manufactured and distributed
pursuant to the requirements of european directives. The original of
the declaration of compliance is available from the manufacturer.
2
P 320
20/09/2011 - 300016243-001-D
Contents
1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.1
2.2
3
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Main dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing the boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.1
3.2
Boiler location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
5
Hydraulic connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5.1
5.2
5.3
5.4
6
Important recommendations on connecting the heating circuit to the boiler and the drinking water system . . . . . . . . . . . . . . . . . .10
Important recommendations for connecting the boiler to the heating circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Filling the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Sludge removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Chimney connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6.1
6.2
Flue size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Chimney connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
7
Fuel-oil or gas connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
8
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
9.1
9.2
9.3
9.4
Sweeping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cleaning the casing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Precautions required in the case of long boiler stops (one or more years) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Precautions required if the heating is stopped when there is a risk of freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
10 Burner maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11 System maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11.1 Water level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11.2 Draining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
13 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
20/09/2011 - 300016243-001-D
P 320
3
1 General
This product will be marketed in the following European Union
member states:
NL - BE - ES - GB - HU - SE
with a gas or oil-burner of the associated category.
Warning
Directive 97/23/EC
Gas and oil boilers with a maximum operating temperature of 110°C
and hot water tanks with a maximum operating pressure of 10 bar
pertain to article 3.3 of the directive, and therefore, cannot be CEmarked to certify compliance with the directive 97/23 EC.
„
4
The boilers and hot water tanks are designed and manufactured in
accordance with the sound engineering practice, as requested in
article 3.3 of the directive 97/23/EC, it is certified by compliance with
the directives 90/396/EC, 92/42/EC, 2006/95/EC and 2004/108/EC.
The boiler shall be assembled and installed by a qualified
professional only.
For a proper operating of the boiler, follow carefully the instructions.
Symbols used
Caution danger
Risk of injury and damage to equipment. Attention must be paid to the
warnings on safety of persons and equipment
Specific information
Information must be kept in mind to maintain comfort
Z
Reference
Refer to another manual or other pages in this instruction manual
P 320
20/09/2011 - 300016243-001-D
2 Description
The boilers of the P 320 range are pressurised hot water boilers
designed for connecting to a flue pipe which require a separate
automatic fuel-oil or gas burner.
The useful power of P 320 boilers is between 55 and 280 kW.
Models available
Boiler with control panel, which may be fitted with an optional
Rematic 2945 C3K control unit for heating only or heating and
domestic hot water production.
20/09/2011 - 300016243-001-D
P 320
5
2.1 Technical specifications
Maximum operating pressure: 6 bar
Safety thermostat setting: 110 °C
Boiler thermostat setting: 30 to 90°C
Boiler
P 320-4
P 320-5
P 320-6
P 320-7
P 320-8
P 320-9
Useful output
kW
70-105
105-140
140-180
180-230
230-280
280-330
Power input
kW
76-117
115-156
153-199
197-253
252-309
305-361
4
5
6
7
8
9
Number of sections
Water content
l
96
116
136
156
176
196
Water resistance
∆ T = 15K (1)
mbar
6.2
10.9
20.4
30
44.5
63.8
Pressure in the furnace for
nozzle pressure = 0
mbar
+0.3
+0.6
+1.1
+1.6
+2.2
+2.5
°C
< 210
< 210
< 210
< 210
< 210
< 210
Flue gas temperature (1) (3)
Mass flue gas flow rate (1)
Combustion chamber
Maintenance consumption
Fuel oil
Kg/h
178
238
306
391
475
560
Gas
Kg/h
187
250
321
410
499
588
Inscribed diameter
mm
377
377
377
377
377
377
Depth
mm
621
781
941
1101
1261
1369
Volume
m3
0.096
0.122
0.148
0.174
0.200
0.226
%
0.17
0.14
0.13
0.11
0.10
0.09
kg
610
739
845
980
1101
1228
by 50°C
Shipping weight
(1) Nominal operation (top boiler power)
(2) CO
2 = 13.1 to 13% with fuel oil and 9.5% with natural gas.
(3) Boiler temperature: 80 °C, Ambient temperature: 20 °C
1 mbar = 10 mmWG = 10 daPa
order for the boiler to operate correctly, it is imperative
toIn respect
the draught at the nozzle: 0 at the nozzle.
6
P 320
20/09/2011 - 300016243-001-D
2.2 Main dimensions
(a) Rp 1 1/2 socket for the safety control unit
(d) 2 1/2 heating return (flange + counter flange)
(b) 2 1/2 heating outlet (flange + counter flange)
(e) Rp 1 1/2 draining outlet (supplied with plug)
(c) Sludge removal hole Ø Rp 2 1/2
P 320-4
P 320-5
P 320-6
P 320-7
P 320-8
P 320-9
L (mm)
991
1151
1311
1471
1631
1791
P (mm)
490
650
810
970
1130
1290
R (mm)
180
180
180
200
200
200
20/09/2011 - 300016243-001-D
P 320
7
3 Installing the boiler
3.1 Boiler location
The P320 boiler does not require a special base for its assembly.
Their closed furnace system means that the floor need not have
refractory properties. All you have to ensure is that the floor can
support the weight of the boiler when it is fitted for operation. If the
boiler location is not determined precisely, leave enough space
around the boiler to facilitate monitoring and maintenance
operations.
Boiler
P 320-4
P 320-5
P 320-6
P 320-7
P 320-8
P 320-9
A
838
998
1158
1318
1478
1638
Pay attention to the overall volume of the burner when the
door
is open. To install several boilers in cascade, these
dimensions should be adapted accordingly.
8
P 320
20/09/2011 - 300016243-001-D
3.2 Ventilation
The location of air inlets in relation to the high ventilation openings
shall ensure that the air is renewed in the entire volume of the boiler
room.
It is in any case imperative to conform to the local regulations in force.
Caution:
In order to avoid damage to the boiler, it is necessary to prevent the
contamination of combustion air by chlorine and/or fluoride
compounds, which are particularly corrosive.
These compounds are present, for example, in aerosol sprays,
paints, solvents, cleaning products, washing products, detergents,
glues, snow clearing salts, etc.
Therefore:
•
•
Do not pull in air evacuated from premises using such products:
hairdressing salons, dry cleaners, industrial premises (solvents),
premises containing refrigeration systems (risk of refrigerant
leakage), etc.
Do not stock such products close to the boilers.
If the boiler and/or peripheral equipment are corroded by such
chloride or fluoride compounds, the contractual guarantee
cannot be applied.
4 Mounting
ZFor mounting instructions, see installation instructions.
20/09/2011 - 300016243-001-D
P 320
9
5 Hydraulic connections
5.1 Important recommendations on connecting the heating circuit to the boiler and the
drinking water system
Installation must be carried out in accordance with the prevailing
regulations, the codes of practice and the recommendations in these
instructions.
The expansion vessel must be connected directly to the boiler
without valves or stop valves.
Example of an installation:
The example of an installation shown below does not cover every
possible configuration. Its sole aim is to draw your attention to the
basic rules to be respected. Comply at all times with the codes of
practice and the prevailing national or local regulations.
Likewise, the safety valve must be connected directly to the boiler
without valves or stop valves.
P 320 boiler with domestic hot water production using an independent tank
3
7
5
10
9
15
9
9
14
9 27 11
16
13
27
20 9
2
17
57
9
19
12
9
17
9
1
6
9
9
9
56
7 9
26
18
32
27
9
31
29
9
17
30
1.
2.
3.
5.
6.
7.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
26.
27.
10
Heating flow
Heating return
3 bar safety valve + manometer
Flow switch
Air separator
Automatic air vent
Isolating valve
3-way mixing valve
Boiler pump
Sludge decanting pot (particularly recommended on older
installations)
Flush valve
Water low safety pressure-sensitive switch
Shunt pump
Expansion vessel
Drain cock
Heating circuit filling (with disconnector depending on prevailing
regulations)
Water treatment if TH > 25°
Water meter
DHW load pump
Non-return valve
28.
29.
30.
31.
32.
56.
57.
P 320
28
8219N008C
Domestic cold water inlet
Pressure reducer (if mains pressure 5.5 bar)
Sealed safety unit calibrated to 7 bar with indicator type discharge
Independent domestic hot water tanks
Domestic hot water loop pump (optional)
Domestic hot water circulation loop return
Domestic hot water outlet
20/09/2011 - 300016243-001-D
5.2 Important recommendations for connecting the boiler to the heating circuit
Installation must be carried out in accordance with the prevailing
regulations, the codes of practice and the recommendations in these
instructions.
`Minimum safety valve flowrate as a function of maximum boiler nominal output:
Minimum relieving capacity
Example
Maximum gross boiler output
Maximum boiler nominal output is 200 kW.
Minimum safety valve flowrate must be 1500 Kg/h
`Water flow in the boiler :
The water flow in the boiler when the burner is operating must correspond with the following formulae:
- Nominal water flow Qn = 0.86 Pn/20
- Minimum flow Qmin = 0.86 Pn/45 (this flow also corresponds with the minimum recycle flow in the boiler)
- Maximum water flow Qmax = 0.86 Pn/5
Qn = flow in m3/h
Pn = Nominal output (full boiler output) in kW.
`Operation in cascade
After stopping the burner:
- Timeout required before the order to close a 2 way valve: 3 min
- Switch a possible shunt pump (located between the boiler and a butterfly valve) off via the end of run contact of the butterfly valve
`Operation with 2-stage burner
- The water temperature in the boiler is maintained at 50°C or more ; The first stage must be set to a minimum of 30% of the nominal stage
- Operation at modulated low temperature (minimum outlet temperature: 30°C) ; The first stage must be set to a minimum of 50% of the
nominal stage
20/09/2011 - 300016243-001-D
P 320
11
`Operation with modulating burner
- The water temperature in the boiler is maintained at 50°C or more: The burner can modulate down to 30% of the nominal stage
- Operation at modulated low temperature (minimum outlet temperature: 30°C) ; The burner can modulate down to 50% of the nominal stage
5.3 Filling the system
Filling shall be performed with a low flow rate from a low point in the
boiler room in order to ensure that all the air in the boiler is bled from
the high point of the system.
All the pumps must be stopped before filling (included shunt
pump(s)).
VERY IMPORTANT: Instructions for starting up the boiler
for
the first time after the system is fully or partly drained:
If all the air is not bled naturally to an expansion vessel
which opens out onto the air, the system must include
manual bleeder valves, in addition to automatic bleeder
valves with the capability to bleed the system by
themselves when it is operating, the manual bleeder valves
are used to bleed all the high points of the system and to
make sure that the filled system is free of air before the
burner is turned on.
Do not add cold water suddenly into the boiler when it is
hot.
5.4 Sludge removal
A tapped Ø 1’’ 1/2 hole with a plug has been provided on the bottom
of the front of the boiler.. Fit a 1/4 turn valve (not supplied) on the
opening to remove the sludge.
Sludge removal leads to the draining of large quantities of water, so
remember to refill the system after the operation.
Note:
never replace a boiler in an existing system without carefully rinsing
the system first. Install a sludge decanting pot on the return pipe, very
close to the boiler.
12
P 320
20/09/2011 - 300016243-001-D
6 Chimney connection
The high-performance features of modern boilers and their use in
specific conditions as a result of the advance in burner technology
(e.g. first-stage or low modulation range operation) lead to very low
flue gas temperatures (<160°C).
For this reason:
- Use flue gas pipes designed to enable the flow of condensates
which may result from such operating modes in order to prevent
damage to the chimney.
- Install a draining tee at the bottom of the chimney.
The use of a draught moderator is recommended as well.
6.1 Flue size
Refer to applicable regulations while determining the size of the flue.
Please note that P 320 boilers have pressurised and tight furnaces
and that the pressure at the nozzle must not exceed 0 mbar, unless
special sealing precautions have been taken, for instance in order to
connect a static condenser/regenerator.
6.2 Chimney connection
The connection shall be removable, and offer minimum load losses,
i.e. it must be as short as possible with no sudden change in section.
Its diameter shall always be at least equal to that of the boiler outlet,
i.e.:
Ø 180 mm: for 4 to 6 sections
Ø 200 mm: for 7 to 9 sections
Fit a measuring point (Ø 10 mm hole) on the flue, in order to adjust
the burner (combustion check).
20/09/2011 - 300016243-001-D
P 320
13
7 Fuel-oil or gas connections
ZRefer to the instructions supplied with the burner.
head deflector must be flush with the insulation
ofThetheburner
burner door.
B
O
E
F
M001614-B
A: Furnace door insulation
B: Turbulator
C: 4 markings on Ø 170
D: 4 markings on Ø 200
E: 4 markings on Ø 220
8 Electrical connections
Refer to the connection instructions supplied with the control
Zpanel.
14
P 320
20/09/2011 - 300016243-001-D
9 Maintenance
The operations described below shall only be performed
with
the boiler and power supply off.
9.1 Sweeping
The boiler will only operate efficiently if the exchange surfaces
are kept clean.
„
Cleaning the flue gas circuit
- Switch off the boiler electrical power supply.
- Unhook the front panel.
- Open the cleaning door (top door) by unscrewing the 4 closing nuts
(17 mm spanner),
- Remove the baffle plates,
- Carefully sweep the flue ways with the brush supplied for that
purpose,
- Also sweep the baffle plates and the front panel,
- If possible, use a vacuum cleaner,
- Replace the baffle plates,
- Close the door.
20/09/2011 - 300016243-001-D
The boiler should be cleaned as soon as required and as the
chimney, at least once a year or more, depending upon applicable
regulations and specific needs.
„
Cleaning the combustion chamber
- Unscrew the 4 closing nuts and open the furnace door
- Brush out the inside of the furnace
- Use a vacuum cleaner to remove any soot which has accumulated
in the combustion chamber
- Close the door and replace the front panel.
P 320
15
„
Positioning of the baffles
„
The first two baffles on the two lower flue ways are fitted
with
stops to position them in the right place.
Cleaning the flue gas box
- Remove the left and right cleaning hatches from the flue gas box
(2 butterfly screws) and use a vacuum cleaner to remove any soot
which has accumulated
- Replace the cleaning hatches.
(1) Stop
Baffle plates
upper
interior
Flue ways
P 320-4
P 320-5
P 320-6
P 320-7
P 320-8
P 320-9
410 mm
A+B
-
8
8
-
-
-
570 mm
A+B
4
-
-
4
4
4
412 mm
C
2
2
2
2
2
2
9.2 Cleaning the casing material
Use a soapy solution and a sponge only. Rinse with clean water and
dry with chamois leather or a soft cloth.
9.3 Precautions required in the case of long boiler stops (one or more years)
- The boiler and the chimney must be swept carefully.
- Close all the doors of the boiler to prevent air from circulating inside
the boiler.
- We advise removing the pipe which connects the boiler to the
chimney and to close off the nozzle with a cover.
9.4 Precautions required if the heating is stopped when there is a risk of freezing
We recommend the use of a correctly dosed antifreeze agent to
prevent to the heating circuit from freezing. If this cannot be done,
drain the system completely.
16
P 320
20/09/2011 - 300016243-001-D
10 Burner maintenance
Refer to the instructions supplied with the burner.
11 System maintenance
11.1 Water level
Regularly check the level of water in the system and top up if
required, taking care that cold water is not added suddenly into the
boiler when it is hot.
This operation should be required only a few times in each heating
season, with very low quantities of water; otherwise, look for the leak
and repair it.
11.2 Draining
We advise you against draining the system unless it is absolutely
necessary.
20/09/2011 - 300016243-001-D
P 320
17
12 Data plate
8553N047B
The rating plate fixed on the side of the boiler during installation is
used to identify the boiler correctly and also provides the main
specifications of the boiler.
Boiler type
Manufacturing date
Year of manufacture
Week of manufacture
Serial no. of the appliance
18
P 320
20/09/2011 - 300016243-001-D
13 Spare parts
To order a spare part, quote the reference number next to the part required.
20/09/2011 - 300016243-002-C
8553N059-C
Boiler body
20/09/2011 - 300016243-001-D
P 320
19
Insulation
90
8553N061A
12x
Base frame
20
P 320
20/09/2011 - 300016243-001-D
Casing - before week 14 / 2008
20/09/2011 - 300016243-001-D
P 320
21
Casing - after week 14 / 2008
A
Table - RC 6
22
P 320
20/09/2011 - 300016243-001-D
Markers
Code no.
Description
Markers
Code no.
Description
Boiler body
30
8219-0019
Lower baffle plate, 412 mm
1
8219-8912
Complete rear section
30
8219-0020
Lower baffle plate, 572 mm
2
8219-8966
Special intermediate section
31
8219-7724
Body screws packet
3
8219-8976
Complete front section
32
8219-8957
Bag of screws for furnace door
4
8116-0571
Nipple
33
9430-5027
0.3 kg can nipple lubricant
5
8219-8968
Complete assembly rod, 4 sections
34
9432-0214
Mastic Novasil S 17
5
8219-8969
Complete assembly rod, 5 sections
5
8219-8970
Complete assembly rod, 6 sections
5
8219-8971
Complete assembly rod, 7 sections
50
9750-5025
Brush
5
8219-8972
Complete assembly rod, 8 sections
51
9750-5076
1000 mm brush rod
5
8219-8973
Complete assembly rod, 9 sections
51
9750-5060
1300 mm brush rod
6.1
8202-0028
Plug 2 1/2" - 1/2"
6.2
8209-0049
Plug 2 1/2" - 1/2" - NL
6.3
9494-8080
Nipple N 241 - 1/2"x1/4"
7
9536-5611
Rp 1/2 sensor tube
8
8013-0028
Solid plug 2" 1/2
9
8553-5513
Flow flange, 3 to 9 sections
10.1
8553-5514
Return flange, 4 to 5 sections
10.2
8553-5515
10.3
Miscellaneous
Base frame
70
8553-7060
Complete frame 4 sections
Package FD 30
70
8553-7061
Complete frame 5 sections
Package FD 31
70
8553-7062
Complete frame 6 sections
Package FD 32
Return flange + distribution pipe, 6 to 8
sections
70
8553-7063
Complete frame 7 sections
Package FD 33
8553-5516
Return flange + distribution pipe, 9 sections
70
8553-7064
Complete frame 8 sections
Package FD 34
10.4
9754-9178
Counter flange
11
9495-0249
Male plug 290 T9 - R 1 1/2
70
8553-7065
Complete frame 9 sections
Package FD 35
11.1
9501-4122
Flange gasket
12
8104-8984
Hinge
13
8219-8916
Sweeping door
90
8553-5507
Complete boiler body insulation, 4 sections
14
9425-0306
Inner protection, sweeping door
90
8553-5508
Complete boiler body insulation, 5 sections
15
9425-0305
Insulation, sweeping door
90
8553-5509
Complete boiler body insulation, 6 sections
16
9508-6032
10 Ø thermocord gasket
90
8553-5510
Complete boiler body insulation, 7 sections
17
9756-0203
Pin Ø 12x350
90
8553-5511
Complete boiler body insulation, 8 sections
18
8219-8913
Ø 180 complete nozzle
90
8953-5512
Complete boiler body insulation, 9 sections
18
8219-8914
Ø 200 complete nozzle
19
8219-0206
Right hand nozzle cover
20
8219-0207
Left hand nozzle cover
100
100004865
Complete casing 4 sections
21
8219-8953
Complete combustion chamber door, ø 135
100
100004866
Complete casing 5
22
9425-0303
Internal protection, combustion chamber
door
100
100004867
Complete casing 6
100
100004868
Complete casing 7
23
9425-0302
Furnace door guard
100
100004869
Complete casing 8
24
9425-0301
Furnace door insulation
100
100004880
Complete casing 9
25
8015-7700
Sight glass + gaskets
101
200013020
Front panel
26
9757-0027
Inspection flange
102
200004840
Upper crosspiece
27
9495-0050
Plug 1/4"
103
200004839
Lower cap
28
8219-0539
Guide rail for combustion chamber door
104
200005032
Complete rear panel
29
8219-0017
Upper baffle plate, 410 mm
105
200005033
Complete side panel right, 4 sections
29
8219-0018
Upper baffle plate, 570 mm
105
200005034
Complete side panel right, 5 sections
20/09/2011 - 300016243-001-D
Insulation
Casing - after week 14 / 2008
P 320
23
Markers
Code no.
105
200005035
105
Description
Markers
Code no.
Description
Complete side panel right, 6 sections
106
8553-8553
Complete side panel left, 6 sections
200005036
Complete side panel right, 7 sections
106
8553-8554
Complete side panel left, 7 sections
105
200005037
Complete side panel right, 8 sections
106
8553-8555
Complete side panel left, 8 sections
105
200005038
Complete side panel right, 9 sections
106
8553-8556
Complete side panel left, 9 sections
106
200005039
Complete side panel left, 4 sections
107
8553-8512
Complete rear cover, 4 sections
106
200005040
Complete side panel left, 5 sections
107
8553-8513
Complete rear cover, 5 sections
106
200005041
Complete side panel left, 6 sections
107
8553-8514
Complete rear cover, 6 sections
106
200005042
Complete side panel left, 7 sections
107
8553-8515
Complete rear cover, 7 sections
106
200005043
Complete side panel left, 8 sections
107
8553-8516
Complete rear cover, 8 sections
106
200005044
Complete side panel left, 9 sections
107
8553-8517
Complete rear cover, 9 sections
107
200004830
Complete rear cover, 4 sections
108
8553-8518
Complete front cover
107
200004831
Complete rear cover, 5 sections
109
8553-8520
Screw bag - Casing
107
200004832
Complete rear cover, 6 sections
107
200004833
Complete rear cover, 7 sections
K - RC 6 control panel
107
200004834
Complete rear cover, 8 sections
107
200004835
Complete rear cover, 9 sections
Refer to the Spare Parts list in the panel
instructions.
108
200005045
Complete front cover
109
200005046
Screw bag
110
200004849
4-section cable way
110
200004850
5-section cable way
110
200004851
6-section cable way
110
200004852
7-section cable way
110
200004853
8-section cable way
110
200004854
9-section cable way
111
200004841
Cable protection
Casing - before week 14 / 2008
24
100
100003501
Complete casing 4 sections
100
100003502
Complete casing 5
100
100003503
Complete casing 6
100
100003504
Complete casing 7
100
100003505
Complete casing 8
100
100003506
Complete casing 9
101
200003545
Front panel
102
8553-8000
Upper crosspiece
103
8553-5506
Lower cap
104
8553-8519
Complete rear panel
105
8553-8545
Complete side panel right, 4 sections
105
8553-8546
Complete side panel right, 5 sections
105
8553-8547
Complete side panel right, 6 sections
105
8553-8548
Complete side panel right, 7 sections
105
8553-8549
Complete side panel right, 8 sections
105
8553-8550
Complete side panel right, 9 sections
106
8553-8551
Complete side panel left, 4 sections
106
8553-8552
Complete side panel left, 5 sections
P 320
20/09/2011 - 300016243-001-D
20/09/2011 - 300016243-001-D
P 320
25
26
P 320
20/09/2011 - 300016243-001-D
20/09/2011 - 300016243-001-D
P 320
27
© Copyright
All technical and technological information contained in these technical instructions, as well as any
drawings and technical descriptions supplied, remain our property and shall not be multiplied
without our prior consent in writing.
Subject to alterations.
20/09/2011
300016243- 001- D