Rangemaster | Classic Deluxe 110 | User guide | Rangemaster Classic Deluxe 110 User guide

Britain’s No.1 Range Cooker
USER GUIDE &
INSTALLATION INSTRUCTIONS
110 Induction G5
RANGEMASTER COOKWARE
Our range cookers are well known for providing the
best possible cooking performance and years of
faithful service. However, a great cooker alone cannot
guarantee perfect results every time. The other vital
ingredients are of course enthusiasm and quality
cookware.
We offer cookware to work perfectly with all fuel types
manufactured by Rangemaster, including induction
hobs. You can be assured of functionality with style, as
well as the quality and meticulous attention to detail
you expect from the pioneers of range cooking.
Visit: www.rangemastercookshop.co.uk
FRUITY BAKED PUDDING
Serves 4–6
Ingredients
Method
•
•
•
•
•
•
1. Preheat the oven to 200 °C (for a conventional oven),
180 oC (for a fan oven) or gas mark 6.
•
•
•
•
•
•
•
Oil for greasing
100 g strawberries
100 g raspberries
100 g redcurrants
100 g blackberries
or a 400 g mixture of any soft
fruits
2 medium eggs
30 g caster sugar
80 ml skimmed milk
2 tsp vanilla extract
60 g plain flour (sifted)
1 tsp baking powder
Icing sugar to dust
2. Lightly grease a dish 26 cm wide x 4 cm deep.
3. Thickly slice any large strawberries and place them with the other fruits
into an ovenproof dish, deep enough so the berries are about 2 deep.
4. Whisk the eggs and caster sugar until pale and fluffy. Beat the milk and
vanilla extract into the mixture and then fold in the sifted flour and
baking powder.
5. Pour the cake mix over the fruit and bake on the centre shelf of the
oven for 15-20 minutes, or until the mixture is cooked through and
golden on the top.
6. Dust with icing sugar and serve immediately with cream or crème
fraiche.
ROAST LOIN OF PORK WITH PROSCUITTO
& BAY LEAVES
Ingredients
Method
• 3 kg (6½ lb) skinned and
boned loin of pork
• 2 x 70 g packs prosciutto
• Grated zest of 2 lemons
• Bay leaves
• Salt and freshly ground
black pepper
1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a fan
oven) or gas mark 7.
For the sauce:
• 1 tablespoons plain flour
• 4 tablespoons lemon
juice
• Chicken stock/water
2. Spread one of the packs of prosciutto over a chopping board; place
the pork on top with the outer (fat) part of the pork resting on the
prosciutto.
3. Sprinkle the lemon zest onto the inside of the meat and season well. Lay
the remaining prosciutto on top of the zest and roll up.
4. Secure the pork with string or silicone bands and thread bay leaves
under the string, covering the whole piece of pork. Put the meat on to
a trivet over a large roasting tin containing enough water to cover the
base.
5. Place into the oven and cook for 30 minutes. Reduce the heat to 180 °C
conventional oven/160 °C fan oven/gas 4 and continue roasting for a
further 25 minutes per 500 g. Should the prosciutto start becoming too
brown, cover with some foil.
6. When the pork is cooked, place onto a warm plate, cover with foil and
allow to rest for at least 20 minutes.
7. Spoon off most of the fat from the roasting tin and stir the flour into the
remaining. Gradually add the stock and lemon juice, adding more stock
until the desired consistency is reached and simmer for 5 minutes. Check
the seasoning, adding more pepper or lemon juice as necessary.
8. Remove the string or bands from the pork and carve into slices, serve
with the sauce.
Contents
1.
Before You Start...
1
6.Troubleshooting
24
Installation and Maintenance
1
Peculiar Smells
1
7.Installation
27
Ventilation1
Personal Safety
1
Hob Care
3
Cooker Care
3
2. Cooker Overview
4
27
Safety Requirements and Regulations
27
Provision of Ventilation
27
Location of Cooker
27
Positioning the Cooker
28
Moving the Cooker
28
29
The Hob
4
The Grill / Glide-out Grill
8
Repositioning the Cooker Following
Connection
The Ovens
9
Levelling the Cooker
29
The Clock
12
Electrical Connection
30
Accessories16
Final Checks
30
Main Oven Light
Final Fitting
31
Customer Care
31
16
Storage17
3.
Dear Installer
18
8. Circuit Diagrams
32
Hints on Using Your Induction Cooker
18
Circuit Diagram: Hob
32
Tips on Cooking with the Timer
18
General Oven Tips
18
Circuit Diagram: Multi-function
Oven (Elan)
33
Cooking Tips
Circuit Diagram: Multi-function Oven
4.
Cooking Table
19
(Classic Deluxe & Professional Deluxe)
5.
Cleaning Your Cooker
20
(Classic, Toledo & Professional+)
Circuit Diagram: Conventional Oven
Hob20
9. Technical Data
Grills21
Control Panel and Doors
34
35
36
22
Ovens22
Cleaning Table
110 Induction G5
23
i
U110202-03
ii
1. Before You Start...
This User Guide covers a number of different models.
Although some of the illustrations will look different to
your particular model the functions will be the same. We
hope the meaning is clear.
Ventilation
Caution: The use of a cooking appliance results in
nn
the production of heat and moisture in the room in
which it is installed. Therefore, make sure that the
kitchen is well ventilated: keep natural ventilation
holes open or install a powered cookerhood that
vents outside. If you have several hotplates on, or
use the cooker for a long time, open a window or
turn on an extractor fan.
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start, particularly if you
have not used an induction cooker before.
This appliance is designed for domestic cooking
nn
only. Using it for any other purpose could invalidate
Personal Safety
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
Important information for pacemaker and implanted
insulin pump users: The functions of this hob comply with
the applicable European standards on electromagnetic
interference. If you are fitted with a pacemaker or
implanted insulin pump and are concerned please consult
your doctor for medical advice.
Installation and Maintenance
All installations must be in accordance with the relevant
instructions in this booklet, with the relevant national
and local regulations, and with the local electricity supply
companies’ requirements.
Do not modify this appliance.
nn
This appliance can be used by children aged from
nn
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Make sure that the cooker is correctly wired and switched on.
The hob control display will flash for about 2 seconds
during first power setting – this is normal.
Set the clock to make sure that the ovens are functional –
see the relevant section in this manual.
Only a qualified service engineer should service the cooker,
and only approved spare parts should be used.
WARNING: The appliance and its accessible parts
nn
become hot during use and will retain heat even
Always allow the cooker to cool and then switch it off at the
mains before cleaning or carrying out any maintenance work,
unless specified otherwise in this guide.
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
Peculiar Smells
When you first use your cooker it may give off an odour. This
should stop after use.
When the hob is in use keep magnetic items, such as
nn
credit and debit cards, floppy disk, calculators, etc.
Before using your cooker for the first time, make sure that all
packing materials have been removed and then, to dispel
manufacturing odours, turn all the ovens to 200 °C and run
for at least an hour.
CAUTION: A long term cooking process has to be
nn
supervised from time to time. A short term cooking
away.
process has to be supervised continuously.
Danger of fire: DO NOT store items on the cooking
nn
surfaces.
Before using the grill for the first time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
To avoid overheating, DO NOT install the cooker
nn
behind a decorative door.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
Accessible parts will become hot during use and will
nn
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-fitting or hanging clothes when
using the appliance.
DO NOT use a steam cleaner on your cooker.
nn
1
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
Fig.1-1
Take care when touching the marked cooking areas
nn
of the hob.
When the oven is on, DO NOT leave the oven door
nn
open for longer than necessary, otherwise the
ArtNo.324-0001 Steam burst
control knobs may become very hot.
When using the grill, make sure that the grill pan
nn
is in position and pushed fully in, otherwise the
control knobs may become very hot.
Always keep combustible materials, e.g. curtains, and
flammable liquids a safe distance away from your cooker.
Fig.1-2
ArtNo.312-0001 Not cooking surface
DO NOT spray aerosols in the vicinity of the cooker
nn
while it is on.
Cooking high moisture content foods can create a ‘steam
burst’ when an oven door is opened (Fig.1-1). When opening
an oven stand well back and allow any steam to disperse.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch fire if brought into contact with a hot surface.
NEVER operate the cooker with wet hands.
nn
DO NOT use aluminium foil to cover shelves, linings
nn
or the oven roof.
NEVER heat unopened food containers. Pressure
nn
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always make sure
nn
that you position the handles away from the edge of
the hotplate.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on fire. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
nn
Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER leave a chip pan unattended. Always heat fat
nn
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
Do not use the top of the flue (the slot along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
2
DO NOT use water on grease fires and never pick
nn
up a flaming pan. Turn off the controls and then
Fig.1-3
smother a flaming pan on a surface unit by covering
the pan completely with a well fitting lid or baking
tray. If available, use a multi-purpose dry chemical
or foam-type fire extinguisher.
Take care that no water seeps into the appliance.
This appliance is heavy so take care when moving it.
nn
Hob Care
NEVER allow anyone to climb or stand on the hob.
nn
NEVER cook directly on the hob surface (Fig.1-2).
nn
DO NOT use the hob surface as a cutting board.
nn
Fig.1-4
DO NOT leave utensils, foodstuffs or combustible items on
the hob when it is not in use (e.g. tea towels, frying pans
containing oil).
DO NOT place plastic or aluminium foil, or plastic
nn
containers, on the hob.
DO NOT leave the hob zones switched on unless
nn
being used for cooking.
ArtNo.312-0003 Moving pans
DO NOT stand or rest heavy objects on the hob. Although the
ceramic surface is very strong, a sharp blow or sharp falling
object (e.g. a salt cellar) might cause the surface to crack or
break (Fig.1-3).
Fig.1-5
Should a crack appear in the surface, disconnect the
nn
appliance immediately from the supply and arrange
for its repair.
Always LIFT pans off the hob. Sliding pans may cause marks
and scratches (Fig.1-4). Always turn the control to the OFF
position before removing a pan.
ArtNo.090-0007 90 Ceramic:
oven steam out the back
Take care when placing hot lids onto the hob
nn
surface. Lids that have been covering boiling or
steaming foods can ‘stick’ to the ceramic glass.
Should this occur, DO NOT attempt to lift the lid
off the hotplate: this may damage the hob surface.
Instead, carefully slide the lid to the edge of the hob
surface and remove.
DO NOT place anything between the base of the pan and the
hob surface (e.g. asbestos mats, aluminium foil, wok stand).
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours (Fig.1-5).
3
2. Cooker Overview
ArtNo.025-0005 - Overview - 90 induction - 2 button clock & GO grill
Fig.2-1 A
B
ºC
ºC
M
C
E
D
ArtNo.190-0002 - 110 Induction annotated GENERIC
F
Your 110 induction cooker (Fig.2-1) has the following
features:
Fig.2-2
A.
B.
C.
D.
E.
5 induction cooking zones
Control panel
A separate grill or glide-out grill (depending on model)
A conventional or multi-function oven (programmable,
depending on model see Table 2-1)
Fan oven (programmable on some models)
F.
Storage drawer
The Hob
Fig.2-3
Use only pans that are suitable for induction hobs. We
recommend stainless steel, enamelled steel pans or cast iron
pans with enamelled bases. Note that some stainless steel
pans are not suitable for use with an induction hob so please
check carefully before purchasing any cookware.
Pans made of copper, aluminium or ceramic are not suitable
for use on an induction hob. The kind of pan you use and the
quantity of food affects the setting required. Higher settings are
required for larger quantities of food.
Pots and pans should have thick, smooth, flat bottoms
(Fig.2-2). This allows the maximum heat transfer from the
hob to the pan, making cooking quick and energy efficient.
Never use a round-bottomed wok, even with a stand.
4
The very best pans have bases that are very slightly curved
up when cold (Fig.2-3). If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up the
metal expands and lies flat on the cooking surface.
Make sure that the base of the pan is clean and dry to prevent
any residue burning onto the hob panel. This also helps
prevent scratches and deposits.
Take care when placing hot lids onto the hob
nn
surface. Lids that have been covering boiling or
steaming foods can ‘stick’ to the ceramic glass.
Should this occur, DO NOT attempt to lift the lid
off the hotplate: this may damage the hob surface.
Instead, carefully slide the lid to the edge of the hob
surface and remove.
Model
Programmable Oven
Classic
right-hand oven
Professional+
right-hand oven
Toledo
right-hand oven
Classic Deluxe
left-hand oven
Professional Deluxe
left-hand oven
Elan
left-hand oven
Table 2-1
Fig.2-4
Max: 1.85 kW
Boost: 2.5 kW
Always use pans that are the same size as (or slightly larger
than) the areas marked on the hob. Using a lid will help the
contents boil more quickly.
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.85 kW
Boost: 2.5 kW
Always take care before touching the surface, even
nn
when the hob is turned off. It may be hotter than you
think!
The induction hob comprises of five cooking zones
containing induction elements with different ratings and
diameters (Fig.2-4) each with a pan detector and residual
heat indicator, and a hob control display.
The hob control display (Fig.2-5) informs you of the following
induction hob functions:
Pan Detector
H
Residual Heat Indicator
A
Automatic Heat-up
Child Lock
L1/L2 Low Temperature Setting
P
Power Boost Setting
Max: 1.15 kW
Boost: 2.0 kW
Max: 1.15 kW
Boost: 2.0 kW
Fig.2-5
Pan Detector,
IMPORTANT: After use, switch off the hob element by its
control and DO NOT RELY on the pan detector.
If a cooking area is switched on and there is no pan in place
or if the pan is too small for the cooking area, then no heat
will be generated. The symbol [ ] will appear on the hob
control display; this is the “pan-missing symbol”. Place a pan
of the correct size on the cooking area and the [ ] symbol
will disappear and cooking can begin. After 10 minutes
without detecting a pan the cooking zone will switch off
automatically.
Cooking Zone
Minimum Pan Diameter
(Pan Base) mm
Front left
140
Rear left
180
Centre
180
Rear right
180
ArtNo.051-0002 - Min pan diameter
Front right
140
Table 2-2 shows the minimum pan sizes recommended for
each cooking zone.
Note: Using pans with a base diameter smaller than those
recommended will result in a power reduction.
Table 2-2
5
Residual Heat Indicator, H
Power Level
Auomatic Heat-up Time at
100% (min:sec)
1
0:48
2
2:24
3
3:50
4
5:12
5
6:48
Automatic Heat-up, A
6
2:00
7
2:48
8
3:36
This function is available on all of the cooking zones. It
allows rapid heating up of the element to bring the selected
cooking zone up to temperature. Once the zone is at the
required cooking temperature the power level will reduce
automatically to the preset level.
After use, a cooking zone will remain hot for a while as heat
dissipates. When a cooking zone is switched off the residual
heat indicator symbol [H ], will appear in the display. This
shows that the cooking zone temperature is above 60 °C and
may still cause burns. Once the temperature has dropped to
below 60 °C the [H ] will go out.
9
The function is selected by turning the control knob to the
‘A’ position. Turn the control knob momentarily counterclockwise from the zero position until the symbol [A ] is shown
on the hob control display.
Table 2-3
Fig.2-6
1
L
0 A
1
L
0 A
P
P
9
9
9
1
P
9
9
L2
0 A
L2
1
L
P
When the Automatic Heat-up function is activated, the hob
control display will flash alternately between the [A ] setting
and the chosen power level.
1
1
1
0 A
1
1
L
L2
P
L2
0 A
L2
1
L
Once the [A ] is displayed, turn the control knob to the level
of your choice (1 to 9). The pan will heat up at 100% power
for a specified time before the power is reduced to the level
selected.
Once the Automatic Heat-up time has ended the hob display
will stop flashing and will show the chosen power level.
Fig.2-7
The Automatic Heat-up function can be stopped by either
turning the control knob back to the “0” power setting or
turning the control knob to the “9” power setting.
For your guidance Table 2-3 shows the time available at
100% power depending on the power level selected in the
Automatic Heat-up mode.
Child Lock,
IMPORTANT: The child lock can only be activated when all
the cooking zones are switched off.
To prevent the unwanted use by children, the hob can be
locked.
To lock the hob, simultaneously turn the two left-hand
controls counter-clockwise (Fig.2-6) and hold until the
symbol appears in the centre of the hob control display
(Fig.2-7).
Note: [A ] will flash when locking the hob – this is normal.
Locking the hob will NOT affect the ovens; they can still be
used.
To unlock the hob, simultaneously turn the two left-hand
symbol
controls counter-clockwise and hold until the
disappears from the centre of the hob control display.
6
Low Temperature Setting, L1/L2
Maximum Operating Time
Power Level
Each cooking area is equipped with 2 low temperature
settings:
• L1 will maintain a temperature of about 40 °C – ideal for
gently melting butter or chocolate.
• L2 will maintain a temperature of about 90 °C – ideal for
simmering (bring the pan to the boil and then select L2
to keep soups, sauces, stews, etc at an optimal simmer).
The maximum time these settings can be used is 2 hours,
after which the hob will switch off automatically. If required,
you can immediately restart the Low Temperature function by
reactivating L1 or L2. To increase the heat, just turn the control
knob to the required level.
The maximum times for all other power levels are shown in
Table 2-4.
L1 and L2
2 hours
1
6 hours
2
6 hours
3
5 hours
4
ArtNo.051-0002 - Min pan diameter
5 hours
5
4 hours
6
1.5 hours
7
1.5 hours
8
1.5 hours
9
1.5 hours
Power Boost
10 minutes
Table 2-4
Power Boost Setting, P
Fig.2-8
A & B linked
All of the induction cooking zones have Power Boost
available, activated by turning the control knob clockwise
until [P ] is shown on the hob control display.
A
Power Boost allows additional power to be made available for
each of the cooking zones. This is useful to bring a large pan
of water to the boil quickly.
The Power Boost function operates for a maximum of 10
minutes on each zone, after which the power is automatically
reduced to setting 9.
B
D
When using the Power Boost function, the cooking zones are
linked.
C
E
Induction
Fig.2-8 shows the hob layout. Zones A and B are linked
together as are zones C, D and E.
C, D & E linked
This means that when using zone A on Power Boost and then
switching zone B to Power Boost , the power to zone A will
reduce slightly. The last zone switched to Power Boost always
takes priority. Zones C, D and E work in the same way.
This is a built-in safety device.
nn
Deactivate the Power Boost function by turning the control
knob to a lower setting.
Overheat Function
This function identifies when the temperature of the pan rises
rapidly and works to maintain a safe level of pan temperature.
It should not interfere with normal cooking.
Please remember not to leave the hob unattended.
nn
Care should be taken to not allow your cookware to
boil dry.
7
The Grill / Glide-out Grill
Fig.2-9
CAUTION: This appliance is for cooking purposes
nn
only. It must not be used for other purposes, for
example room heating.
CAUTION: Accessible parts may be hot when the grill
nn
is in use. Young children should be kept away.
ArtNo.330-0003 - Grill pan w handle pulled forwards
Open the door and pull the grill pan carriage forward using
the handle (Fig.2-9 and Fig.2-10).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Fig.2-10
Adjust the heat to suit by turning the knob. To heat the whole
grill, turn the knob clockwise (Fig.2-11).
To heat the right-hand half, turn the knob counter-clockwise.
The neon indicator light by the grill control will come on.
For best results, slide the carriage back into the grill chamber
and preheat the appropriate part(s) of the grill for two
minutes. The grill trivet can be removed and the food placed
on it while you are waiting for the grill to preheat.
ArtNo.331-0001Grill pan pulled forwards
DO NOT leave the grill on for more than a few
nn
moments, without the grill pan underneath it,
Fig.2-11
otherwise the knobs may become hot.
Once the grill has preheated, slide the carriage out again.
With the trivet back in place with the food on it, slide the
carriage back into the grill chamber. Make sure that it is
pushed right in.
ArtNo.200-0003 Generic grill control to full
The grill pan trivet can be turned over to give two grilling
positions (Fig.2-12).
NEVER close the grill door when the grill is on.
nn
Fig.2-12
ArtNo.331-0002 Grill pan high/low position
8
The Ovens
Function
Use
The clock must be set to the time of day before the
programmable oven will work. See the following section
on ‘The Clock’ for instructions on setting the time of day.
Defrost
To thaw small items in the oven without
heat
Fan oven
A full cooking function, even heat
throughout, great for baking
Fanned grilling
Grilling meat and fish with the door
closed
Fan assisted
A full cooking function good for roasting
and baking
Conventional oven
A full cooking function for roasting and
baking in the lower half of the oven
A conventional oven has two heating elements – one visible
in the top of the oven and the other under the oven base.
Browning element
To brown and crisp cheese topped
dishes
Note: Be careful to avoid touching the top element and
element deflector when placing or removing items from the
oven.
Base heat
To crisp up the bases of quiche, pizza or
pastry
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
The left-hand oven is either a programmable multi-function
or conventional oven, while the right-hand oven is a fan oven
(programmable on some models).
Conventional Zoned Ovens
Table 2-5
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Similar items being cooked will need to be swapped around
for even cooking.
The Multi-function Oven
Multi-function ovens have an oven fan and oven fan element,
as well as two extra heating elements. One element is in the
top of the oven and the second is under the oven base.
Note: Take care to avoid touching the top element and
element deflector when placing or removing items from the
oven.
The multi-function oven has 3 main cooking functions: fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.
The browning element and base heat can be used in the
latter part of the cooking process to fine tune the results to
your particular requirements.
Use fanned grilling for all your grilling needs and defrost to
safely thaw small items of frozen food.
Table 2-5 gives a summary of the multi-function modes.
The multi-function oven has many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember, not all functions will be
suitable for all food types.
9
It is also possible to bake on two shelves at one time,
although they will need to be swapped over during the
cooking time, as the heat at the top of the oven is greater
than at the base, when using this function.
Multi-function Oven Functions
Rapid Response (Classic Deluxe & Professional Deluxe)
The Rapid Response setting enables you to preheat
the oven faster than normal. It uses the fan oven
element with additional heat from one of the
elements in the top of the oven. Fan ovens heat up quickly;
but the Rapid Response feature speeds this process up
enabling you to start cooking sooner.
This is a fast intensive form of cooking; keep an eye on the
food cooking until you have become accustomed to this
function.
Conventional Oven (Top and Base Heat)
To use the Rapid Response feature, turn the function control
knob to R and set the temperature required. The light on the
control panel next to the function control will come on.
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits.
When the required temperature is reached the top element
will switch off and the light will go out.
Food cooked on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at the top of
the oven than at the base, as in ‘Fan Assisted Oven’ function.
Similar items being cooked will need to be swapped around
for even cooking. This means that foods requiring different
temperatures can be cooked together, using the cooler zone
in the lower half of the oven and hotter area to the top.
The oven temperature is then maintained by the fan oven
element and fan.
Should you choose to place food into the cold oven prior to
cooking while using the Rapid Response function, make sure
that cakes, etc. are not positioned too near the top of the
oven.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Fan Oven
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Similar items being cooked will need to be swapped around
for even cooking.
Browning Element
Fan oven cooking is particularly suitable for baking on several
shelves at one time and is a good ‘all-round’ function. It may
be necessary to reduce the temperature by approximately
10 °C for recipes previously cooked in a conventional oven.
This function uses the element in the top of the oven
only. It is a useful function for the browning or
finishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned being
already hot before switching to the top element.
If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.
Base Heat
Fanned Grilling
This function uses the base element only. It will crisp
up your pizza or quiche base or finish off cooking the
base of a pastry case on a lower shelf. It is also a
gentle heat, good for slow cooking of casseroles in the
middle of the oven or for plate warming.
This function operates the fan while the top element
is on. It produces a more even, less fierce heat than a
conventional grill. For best results, place the food to
be grilled, on a trivet over a roasting tin, which should be
smaller than a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or fish are ideal for grilling in
this way, as the circulated air reduces the fierceness of the
heat from the grill.
The Browning and Base Heat functions are useful additions
to your oven, giving you flexibility to finish off items to
perfection.
Defrost
The oven door should be kept closed while grilling is in
progress, so saving energy.
This function operates the fan to circulate cold air
only. Make sure the temperature control is at 0°C and
that no heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, fish and poultry
to be defrosted.
You will also find that the food needs to be watched and
turned less than for normal grilling. Preheat this function
before cooking.
For best results we recommend that the grill pan is not
located on the top shelf.
Defrosting in this way speeds up the process and protects
the food from flies. Pieces of meat, fish and poultry should
be placed on a shelf, over a tray to catch any drips. Be sure to
wash the shelf and tray after defrosting.
Fan Assisted Oven
This function operates the fan, circulating air heated
by the elements at the top and the base of the oven.
The combination of fan and conventional cooking
(top and base heat) makes this function ideal for cooking
large items that need thorough cooking, such as a large meat
roast.
Defrost with the oven door closed.
Large items, such as whole chickens and joints should not be
defrosted in this way. We recommend this be carried out in a
refrigerator.
10
Defrosting should not be carried out in a warm oven or when
an adjoining oven is in use or still warm.
Fig.2-13
Make sure that dairy foods, meat and poultry are completely
defrosted before cooking.
The Fan Oven
Fan ovens circulate hot air continuously, which means
faster, more even cooking. The recommended cooking
temperatures for a fan oven are generally lower than those
for a non-fan oven.
Note: Please remember that all cookers vary so temperatures
in your new ovens may differ to those in your previous
cooker.
Temperature control
Function control
Fig.2-14
Operating the Ovens
Multi-function Ovens
The multi-function oven has two controls: a function selector
and a temperature setting knob (Fig.2-13).
Turn the function selector control to a cooking function. Turn
the oven temperature knob to the temperature required
(Fig.2-14).
The oven indicator light will glow until the oven has reached
the temperature you selected (Fig.2-15). It will then cycle on
and off during cooking.
Fig.2-15
Conventional and Fan Ovens
Turn the oven knob to the desired temperature (Fig.2-14).
The oven indicator light will glow until the oven has reached
the temperature selected (Fig.2-15). It will then cycle on and
off during cooking.
The Browning Element
The Browning Element is positioned in the top of the lefthand oven.
It can be used at the end of a normal cooking period to give
extra browning to au gratin dishes or give a crisper finish to
meat.
After the normal cooking has finished, turn the left hand
oven thermostat knob clockwise to the browning position,
) on the control knob.
indicated by (
ArtNo.030-0003 Browning
element symbol
Only the Browning Element will operate when the thermostat
is turned to this position.
The top and base cooking elements will automatically switch
off.
11
Fig.2-16
The Clock
ArtNo.300-0004 2-button clock annotated
2-Button Clock
Setting the Time of Day
The 2-button LCD clock is shown in (Fig.2-16). When the
clock is first connected, the display flashes ( 0.00 ) and (
)
alternately.

A
To set the time, turn and hold the Timer knob to the clock
symbol [] and at the same time turn the Adjusting knob left
or right until the clock shows the time of day. Remember this
is a 24-hour clock. Let go of the Timer knob and it will spring
back to the vertical, oven manual setting.
B
A – Timer knob, B – Adjusting knob
Fig.2-17
ArtNo.300-0005 2BC
minute minder setting
IMPORTANT: The programmable oven will not operate
unless the clock has been set.
Setting the Minute Minder
To activate the minute minder turn the Timer knob to the
right to the [] minute minder setting – it should click into
position (Fig.2-17).
Fig.2-18
Rotate the Adjusting knob to set the time required (Fig.2-18).
ArtNo.300-0006 2BC
minute minder setting 2
You can either turn the knob back to the vertical manual
setting [] to keep an eye on the time of day, or leave it in the
[] minute minder position as the time ticks down.
To stop the beeper when it sounds, turn the Adjusting knob
counter-clockwise.
Fig.2-19
•
ArtNo.301-0007 2BC
Stopping the oven 1
•
The ‘cook period’, is the length of time you want the
oven to cook for.
The ‘stop time’, is the time of day you want the oven
to stop cooking.
To Stop the Oven at a Specific Time of Day
Turn the Timer knob to the [] position (Fig.2-19).
Fig.2-20
Use the Adjusting knob to set the ‘stop time’. You can set
the oven to turn on at any time over the following 24-hour
period. AUTO shows in the display (Fig.2-20).
ArtNo.301-0008 2BC
Stopping the oven 2
Turn the Timer knob to the bottom ‘AUTO’ setting to return to
the clock display.
Once the ‘stop time’ is reached, the beeper sounds. Turn the
Timer knob to the vertical [] to return to manual cooking.
Fig.2-21
To Start and then Stop the Oven Using the Timer
ArtNo.301-0009 2BC
Setting the cooking timer
You cannot set a start time directly – this is set
automatically by a combination of the ‘cook time’ and
‘stop time’.
Turn the Timer knob to the [] position (Fig.2-21).
Fig.2-22
Turn the Adjusting knob to set the ‘cooking time’ you need
(Fig.2-22).
ArtNo.301-0010 2BC
Setting the cooking time
Turn the Timer knob to the [] position. The display will
show the current time of day plus the ‘cook time’ you just set.
Use the Adjusting knob to set the ‘stop time’ required
(Fig.2-23).
12
The ‘stop time’ is displayed, followed by ‘AUTO’. Set the oven
to the cooking temperature you need. Turn the Timer knob to
the ‘Auto’ setting.
ArtNo.301-0008 2BC
Stopping the oven 2
Fig.2-23
Art No. 301-0011 2BC
Activating the key lock 1
Fig.2-24
ArtNo.301-0012 2BC
Activating the key lock 2
Fig.2-25
ArtNo.301-0013 2BC
Activating the key lock 3
Fig.2-26
ArtNo.301-0014 2BC
Deactivating the key lock 1
Fig.2-27
ArtNo.301-0015 2BC
Deactivating the key lock 2
Fig.2-28
When your cooking is finished, the beeper sounds. Turn the
Timer knob to the vertical [] to return to manual cooking.
If you are out, do not worry about the beeper going off – it
stops on its own after a while. When you return, turn the
Timer knob to the vertical [] to return to manual cooking.
AUTO is Showing, But You Want to Revert to Manual
Cooking
You can cancel any automatic settings by briefly turning the
Timer knob to the clock symbol [] and then releasing it.
Key Lock
When the key lock is activated the programmable oven is
locked and will not come on.
The non-programmable oven can be operated as usual.
To Activate the Key Lock
Make sure that the clock is in manual mode and cancel
any active programs.
Turn and hold the Timer knob to the clock symbol [] for
about 8 seconds. ‘On’ appears on the display (Fig.2-24).
While still holding the Timer knob turned to the clock symbol
[], turn the Adjusting knob clockwise until the key symbol
[] and ‘OF’ shows on the display (Fig.2-25). Release the
knobs.
The programmable oven is now locked, as is confirmed by the
display showing the time of day alongside the key symbol []
(Fig.2-26).
To Turn Off the Key Lock
Turn and hold the Timer knob to the clock symbol [] for
about 8 seconds. ‘OF’ will appear on the display (Fig.2-27).
While still holding the Timer knob turned to the clock symbol
[], turn the Adjusting knob clockwise until the key symbol
[] goes out on the display and ‘On’ shows (Fig.2-28). Let go
of the knobs.
After a few seconds, the display reverts to showing the time
of day.
The oven can now be used normally.
13
The 6-button Clock
Fig.2-29
Setting the Time of Day
The 6-button LCD clock is shown in Fig.2-29. When the
clock is first connected the display flashes ( 0.00 ) and (
alternately.
)
ArtNo.302-0002 - 6BC annotated
A
B
C
D
E
Press and hold both the [] and [] buttons down
(Fig.2-30). Now press the [+] button (or the [–] button) until
the correct time shows.
F
Do not forget that it is a 24-hour clock.
A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time,
D – Manual, E & F – Time setting buttons
If you need to reset the cooker, turn off the power supply and
wait for a couple of minutes and start again.
Setting the Minute Minder
Fig.2-30
Press and hold the [] button (Fig.2-31), and then press the
[+] button until the length of time you want to cook for is
shown (Fig.2-32).
ArtNo.302-0001 - 6-button clock
You can check the time remaining by pressing []. When the
beeper sounds cancel it by pressing [].
•
Fig.2-31
ArtNo.302-0003 - 6BC
minute minder setting 1
Fig.2-33
ArtNo.302-0005 6BC Stopping the oven 1
Fig.2-35
ArtNo.302-0006 - 6BC
setting the cook time
Fig.2-32
•
The ‘cook period’, is the length of time you want the
oven to cook for.
The ‘stop time’, is the time of day you want the oven
to stop cooking.
To Stop the Oven Automatically
ArtNo.302-0004 Minute minder setting 2
Press and hold the ‘stop time’ [] button (Fig.2-33) and then
press the [+] button (or [–] button) until the required ‘stop
time’ shows (Fig.2-34). AUTO will show in the display.
Once the ‘stop time’ is reached, the beeper sounds. To stop the
beep turn the oven control knob to 0 first and then press []
once; press [] again to return to manual cooking.
Fig.2-34
To Start and Stop the Oven Automatically
ArtNo.302-0005a 6BC Stopping the oven 1a
Before you set the clock you must have two numbers clearly
in mind – the ‘cook period’ and the ‘stop time’.
Note: You cannot set a start time directly – this is set
automatically by setting the ‘cook period’ and the ‘stop time’.
Fig.2-36
Press and hold the [] button (Fig.2-35) and then press the
[+] button (or [–] button) until the required ‘cook period’ shows
(Fig.2-36).
ArtNo.302-0006 - 6BC
setting the cook time
Now press and hold the [] button (Fig.2-37) and then press
the [+] button (or [–] button) until the required ‘stop time’
shows (Fig.2-38). Release the buttons.
AUTO will now show in the display.
Fig.2-37
ArtNo.302-0005 6BC Stopping the oven 1
Set the oven to the required temperature. When cooking is
finished the beeper will sound. Turn the oven knob to the OFF
position first, and then press the [] button once to stop the
beep; press it again to return to manual cooking.
Fig.2-38
ArtNo.302-0005a 6BC Stopping the oven 1a
If you are out, do not worry about the beeper going off, it
stops after a while. When you return, turn the oven knob to 0
first, and then press [] twice to return to manual cooking.
14
AUTO is Showing, You Want to Reset to Manual
Cooking
Fig.2-40
Fig.2-39
To return to manual cooking from any automatic setting,
the ‘cook period’ must be cancelled. Press and hold the []
button and then press the [–] button until the display reads
( 0.00 ).
ArtNo.302-0008 Activating the key lock 1
Press the [] button to return to manual cooking.
ArtNo.302-0009 - Activating
the key lock 2
Key Lock
Activating the key lock will lock the programmable oven and
it will not come on.
Fig.2-41
The non-programmable oven can be operated as usual.
ArtNo.302-0010 Activating the key lock 3
To Activate the Key Lock
Make sure that the clock is in manual mode and cancel
any active programs.
Hold the Minute Minder [] and Cook Period [] buttons.
When ‘On’ appears on the display (Fig.2-39) press the [+]
button once. The key symbol [ ] and ‘OF’ will now show on
the display (Fig.2-40). Release the buttons.
Fig.2-42
ArtNo.302-0011 - 6BC
Deactivating the key lock 1
The programmable oven is now locked, as confirmed by the
display showing the time of day alongside the key symbol
(Fig.2-41).
Fig.2-43
To Turn Off the Key Lock
Hold the Minute Minder [] and Cook Period [] buttons.
When ‘OF’ appears on the display (Fig.2-42) press the [+]
button once. The key symbol [ ] will go out and ‘On’ will show
on the display (Fig.2-43). Release the buttons.
ArtNo.302-0012 Deactivating the key lock 2
After a few seconds the display will revert to show the time of
day.
The oven can now be used normally.
15
Accessories
Fig.2-44
Flat shelf
Oven Shelves – Left-hand (Main) Oven
Shelf guard
In addition to the flat shelves your cooker is supplied with a
drop shelf (Fig.2-44). The drop shelf increases the possibilities
for oven shelf spacing.
The oven shelves can be easily removed and refitted.
Front
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2-45).
Shelf guard
Drop shelf
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig.2-46).
To refit the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2-47).
Front
Fig.2-45
Fig.2-46
ArtNo.320-0011 Removing the shelf 1
Fig.2-47
The Handyrack (Elan, Classic Deluxe and Professional
Deluxe)
The Handyrack (Fig.2-48) fits to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
ArtNo.320-0012 Removing the shelf 2
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to fit the Handyrack. Any other
vessel could be unstable.
Fig.2-48
It can be fitted at two different heights. One of the oven
shelves must be removed and the other positioned to suit.
ArtNo.320-0013 Removing the shelf 3
Fig.2-49
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
ArtNo.320-0014 Handyrack on LH door
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
Fig.2-50
To fit the Handyrack, locate one side of it on the door bracket
(Fig.2-49).
Then spring the other side out to clip it onto the other
bracket (Fig.2-50).
ArtNo.320-0015
Fitting the Handyack 1
Main Oven Light
ArtNo.320-0016
Fitting the handyrack 2
Press the button to turn the lights on (Fig.2-51).
Fig.2-51
If the oven light fails, turn off the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
ArtNo.320-0017
Main oven light
16
Storage
Fig.2-52
The bottom drawer is for storing oven trays and other
cooking utensils.
ArtNo.340-0002 110 removing the drawer
It can get very warm, so do not store anything in it that may
melt or catch fire. Never store flammable materials in the
drawer. This includes paper, plastic and cloth items, such as
cookbooks, plastic ware and towels, as well as flammable
liquids. Do not store explosives, such as aerosol cans, on or
near the appliance.
Flammable materials may explode and result in fire
nn
or property damage.
The drawer can be removed completely for cleaning, etc.
Removing the Drawer
Fig.2-53
Pull the drawer right out (Fig.2-52).
Elan only: Push the ends of the plastic clips – down on the
left-hand side, up on the right-hand side – to release the
catches holding the drawer to the side rails (Fig.2-53). At the
same time pull the drawer forwards and away from the side
rails.
For safety’s sake push the drawer rails back out of the way.
To Fit the Storage Drawer
Carefully slide the drawer back into the cavity.
Elan only: Slide the inner side rails out until fully extended
(Fig.2-54).
Lift the drawer at its sides and locate one of the drawer rails
(approximately 15 mm) onto an inner side rail (Fig.2-55).
Fig.2-54
Rotate the drawer to locate the remaining drawer rail onto
the opposite inner side rail.
Carefully slide the drawer back into the cavity. Some
resistance will be felt as the drawer rails locate fully onto the
inner side rails.
Make sure the inner
rail is forwards
Fig.2-55
15 mm
Approx.
17
3. Cooking Tips
DocNo.030-0010 - Cooking tips - 110 induction GENERIC
Hints on Using Your Induction Cooker
General Oven Tips
If you have not used an induction cooker before please be
aware of the following:
The wire shelves should always be pushed firmly to the back
of the oven.
•
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
•
•
•
Make sure that the pans you have or buy are suitable
for use on the induction hob. Stainless steel, enamelled
steel or cast iron is ideal. Double check before you
buy pans – they must have bases that would attract a
magnet.
Allow time to get used to induction cooking; it is fast
and powerful as well as being gentle. When simmering,
you may notice that liquids appear to stop bubbling and
then start again almost immediately. This is perfectly
normal.
You may notice a faint vibrating sound coming from
the pans when using the induction hob. Again, this is
perfectly normal and will depend upon the type and
style of pans you are using.
The induction heating elements will phase on and off
when cooking. Although an active cooking zone may
appear to switch on and off, a constant heat is still being
supplied to the base of the pan – this is completely
normal.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13 ½”) by 340 mm (13 ½”).
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
•
•
•
•
Tips on Cooking with the Timer
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
•
•
Very perishable foods such as pork or fish should be avoided
if a long delay period is planned, especially in hot weather.
DO NOT place warm food in the oven to be timed.
nn
DO NOT use a timed oven that is already warm.
nn
DO NOT use the timed oven if the adjoining oven is
nn
already warm.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
18
Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.
To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
Where dishes may boil and spill over during cooking,
place them on a baking tray.
The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.
Cover meat when cooking.
Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
4. Cooking Table
DocNo.031-0004 - Cooking table - electric & fan single cavity
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Top (T)
Centre (C)
Base (B)
Oven Shelf Positions
Conventional Oven
Fan Oven
Temperature °C
Temperature
(Shelf Position)
°C
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
200 (C)
190
160 (C)
150
20-25 minutes per 500g +20-25 minutes.
200 (C)
190
15-20 minutes per 500g +15-20 minutes.
160 (C)
150
20 minutes per 500g +20 minutes.
200 (C)
190
15 minutes per 500g +15 minutes.
160 (C)
150
25-30 minutes per 500g.
200 (C)
190
20 minutes per 500g.
140-150 (C)
130-140
220 (C)
210
Large tins 30-35 minutes; individual 10-20 minutes.
140 (C/B)
130
45-50 minutes per 500g of mixture.
Fruit 180 mm tin
150 (C/B)
140
2-2½ hours.
Fruit 230 mm tin
150 (C/B)
140
Up to 3½ hours.
Madeira 180 mm
160 (C/B)
150
80-90 minutes.
Queen cakes
190 (C/B)
180
15-25 minutes.
Scones
220 (C/B)
210
10-15 minutes.
180 mm tin
180 (C/B)
170
20-30 minutes.
210 mm tin
180 (C/B)
170
30-40 minutes.
Shortcrust tarts
200 (C/B)
190
20-30 minutes on a preheated tray.
Fruit pies
200 (C/B)
190
35-45 minutes.
Tartlets
200 (C/B)
190
10-20 minutes according to size.
Puff pastry
210 (C/B)
200
20-40 minutes according to size.
Meringues
100 (C/B)
90
2-3 hours.
Food
Meat
ArtNo.050-0007
Oven shelf positions
T - Top; C - Centre; B - Base
Approximate Cooking Time
ArtNo.050-0001 Gas cooking table
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
30-35 minutes per 500g +30-35 minutes. Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
20-25 minutes per 500g +20-25 minutes.
220°C (210°C for fan oven) and the
30-35 minutes per 500g +30-35 minutes. cooking time adjusted accordingly.
25-30 minutes per 500g +25-30 minutes. For stuffed and rolled meats, add
approximately 10 minutes per 500g,
35-40 minutes per 500g +35-40 minutes. or cook at 200°C (190°C) for 20
25-30 minutes per 500g +25-30 minutes. minutes then 160°C (150°C) for the
remainder.
2-4 hours according to recipe.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Cake
Very rich fruit - Christmas,
wedding, etc.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
Victoria sandwich
Desserts
Baked egg custard
160 (C/B)
150
45-60 minutes.
Baked sponge pudding
180 (C/B)
170
40-45 minutes.
140-150 (C/B)
130-140
210 (C)
200
20-30 minutes.
Milk pudding
Bread
Fish
2 to 3 hours.
Fanned Grilling
Fillet
190 (C/B)
190 (C/B)
15-20 minutes.
Whole
190 (C/B)
190 (C/B)
15-20 minutes per 500g.
Steak
190 (C/B)
190 (C/B)
Steaks according to thickness.
19
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
5. Cleaning Your Cooker
ArtNo.040-0005 - Cleaning - 110 induction GENERIC
Isolate the electricity supply before carrying out any major
cleaning. Allow the cooker to cool.
Fig.5-1
NEVER use paint solvents, washing soda, caustic
nn
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
DO NOT mix different cleaning products – they may
nn
react together with hazardous results.
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
ArtNo.312-0010 Cleaning; scraping the ceramic hob
Remember to switch the electricity supply back on and reset
the clock before reusing the cooker.
Hob
Daily Care
First of all make sure that all heat indicator lights are off and
that the cooking surface is cool. Apply a small dab of ceramic
cleaning cream in the centre of each area to be cleaned.
Dampen a clean paper towel and work the cream onto the
cooking surface. As a final step, wipe the cooking surface with
a clean, dry paper towel.
Cleaning Spills
For spills and boil-overs that occur while cooking, turn the
unit off and wipe the area surrounding the hot zone with a
clean paper towel. If a spill (other than a sugary substance) is
on the hot zone, do not clean until the unit has completely
cooled down, and then follow the instructions below
(‘Cleaning Burned-on Spills’).
If you accidentally melt anything on the surface, or if you spill
foods with a high sugar content (preserves, tomato sauce,
fruit juice, etc.), remove the spill IMMEDIATELY with a razor
scraper, while the unit is still hot.
IMPORTANT: Use an oven glove to protect your hand from
potential burns.
Scrape the major spill or melted material from the cooking
zone and push into a cold area. Then, turn the unit OFF and
allow it to cool before cleaning further. After the cooking
surface cools down and the heat indicator lights go off, follow
the ‘Daily Care’ procedure outlined above.
Cleaning Burned-on Spills
Make sure that the heat indicator lights are off and that the
hob is cool. Remove the excess burned-on substance with a
single-edged razor scraper. Hold the scraper at an angle of
about 30° to the surface and then scrape off the burned-on
matter (Fig.5-1).
Once you have removed as much as possible with the scraper,
follow the ‘Daily Care’ procedure outlined above.
20
Grills
Fig.5-2
The grill pan and trivet should be washed in hot soapy water.
Alternatively, the grill pan can be washed in a dishwasher.
After grilling meats or any foods that soil, leave to soak for a
few minutes immediately after use. Stubborn particles may
be removed from the trivet using a nylon brush.
Before you remove any of the grill parts for cleaning,
nn
make sure that they are cool, or use oven gloves.
ArtNo.331-0001Grill pan pulled forwards
DO NOT use any abrasive substances.
nn
Removing the Glide-out Grill Pan
ArtNo.331-0003 Grill frame out, no pan
The glide-out grill pan can be easily removed for cleaning as
follows:
Fig.5-3
Remove the grill pan support frame by pulling the grill pan
forward (Fig.5-2).
Lift the grill pan clear of the support frame. The support frame
is held to the side rails by two clips on each side (Fig.5-3).
For each side, support the side rail with one hand and with
the other hand lift the frame up and out of the side clips
(Fig.5-4).
For safety, push the side rails back into the grill chamber.
If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig.5-5) and wipe the sides clean with a soft cloth and
mild detergent.
Fig.5-4
DO NOT put the side runners in a dishwasher.
nn
Once you have finished, hook the side rails back onto the
sides of the chamber. To refit the frame, pull the side rails
forward and, for each side in turn, support the side rail and
press the frame down into the side rails.
ArtNo.331-0004 Removing the grill frame
Replace the grill pan. When refitting the grill pan, make sure
that the wide rim is at the front (Fig.5-6).
Fig.5-5
ArtNo.331-0005 Removing the grill rail
Fig.5-6
ArtNo.331-0006 Grill pan plan
21
Control Panel and Doors
Fig.5-7
Avoid using any abrasive cleaners, including cream cleaners.
For best results, use a liquid detergent.
The same cleaner can also be used on the doors. Alternatively,
use a soft cloth wrung out in clean hot soapy water. You can
use the same method for cleaning the control panel and
knobs. After cleaning, polish with a dry cloth.
Glass Fronted Door Panels (some models)
The oven door front panels can be taken off so that the glass
panels can be cleaned. Move the cooker forward to gain
access to the sides (see the ‘Moving the Cooker’ section under
‘Installation’).
ArtNo.320-0002a Proplus oven door side screws
Fig.5-8
Open the oven door slightly and remove the front panel
fixing screws from the door sides, two each side (Fig.5-7).
Carefully lift off the outer door panel. The inside face of the
glass panels can now be cleaned – take care not to disturb or
wet the door insulation.
Note: If the door is triple glazed then the inner two panels are
fixed together and should not be separated. After cleaning,
carefully refit the outer door panel and replace the side fixing
screws.
DO NOT use harsh abrasive cleaners or sharp metal
nn
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Ovens
'Cook & Clean' Panels
The ovens have side ‘Cook & Clean’ panels which have been
coated with a special enamel that partly cleans itself. This
does not stop all marks on the lining, but helps to reduce the
amount of manual cleaning needed.
These panels work better above 200 °C. If you do most of your
cooking below this temperature, occasionally remove the
panels and wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and the oven
heated at 200 °C for about one hour. This will make sure that
the panels are working effectively.
Removing the Panels to Clean the Enamel
Interior
Some of the lining panels can be removed for cleaning.
If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels. You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward off the support brackets (Fig.5-8).
Once the panels have been removed, the oven enamel
interior can be cleaned.
DO NOT use steel wool, oven cleaning pads, or any
nn
other materials that will scratch the surface.
Refit in the reverse order.
22
Cleaning Table
Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Hotplate
Part
Finish
Recommended Cleaning Method
Hob top
Enamel or stainless steel
Hot soapy water, soft cloth. Any stubborn stains remove gently with
a nylon scourer.
Ceramic/induction hob
Toughened glass
Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only)
Non-stick surface
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Warming zone (some models only)
Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Finish
Recommended Cleaning Method
Outside of Cooker
Part
Door, door surround and storage
drawer exterior
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
E-cloth (electrical retailers) or microfibre all-purpose cloth
(supermarket).
Enamel or paint
Stainless steel
Sides and plinth
Painted surface
Hot soapy water, soft cloth.
Splashback/rear grille
Enamel or stainless steel
Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel
Paint, enamel or stainless steel
Warm soapy water. Do not use abrasive cleaners on lettering.
Control knobs/handles & trims
Plastic/chrome, copper or
lacquered brass
Warm soapy water, soft cloth.
Brass
Brass polish.
Toughened glass
Hot soapy water, cream cleaner/scourer if necessary.
Finish
Recommended Cleaning Method
Oven door glass/glass lid (some
models only)
Oven and Grill
Part
Sides, floor & roof of oven NOT
‘COOK & CLEAN’ OVEN PANELS (see Enamel
below)
‘Cook & Clean’ oven panels (some
models only)
Special enamel that partly
cleans itself
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush.
Oven shelves, Handyrack, grill trivet Chrome
An oven interior cleaner that is suitable for chrome. Soap filled pad.
Dishwasher.
Grill pan/meat tin (some models
only)
Hot soapy water. Soap filled pad. Dishwasher.
Enamel
Table 5-1
23
6. Troubleshooting
DocNo.050-0001 - Troubleshooting - Induction GENERIC
The cooling fan
The induction hob incorporates a cooling fan. This
cooling fan is active when either the grill or ovens
are on. Under certain conditions, the cooling fan may
remain active when the grill or ovens are switched off.
This is normal and the fan will switch off automatically.
Interference with and repairs to the hob MUST NOT
nn
be carried out by unqualified persons. Do not try
to repair the hob as this may result in injury and
damage to the hob. Please arrange for repair by a
suitably competent person.
Note: The induction hob is able to self-diagnose a
number of problems and can show this information to
the user via the hob control display. Error codes may be
displayed if your hob has developed a fault.
The fascia gets hot when I use the oven
If the fascia becomes excessively hot when the cooker
is in use then the cooling fan may have failed. Should
this occur please contact your installer, a qualified repair
engineer or Customer Service to arrange for its repair.
If you appliance reports an error or is not working,
you may be able to correct the fault by consulting the
following.
A crack has appeared in the hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Do not use the cooker
until after the repair.
Error code E2 is displayed
The electronic unit is too hot. Please check the
installation of the cooker, making sure that there is
sufficient ventilation. In extreme cases, if a cooking
utensil has been allowed to boil dry this error code
may also be displayed. If in doubt please contact your
installer or a qualified repair engineer.
My hob is scratched
Always use the cleaning methods recommended in this
guide, and make sure that the pan bottoms are smooth
and clean.
No display operation
Over voltage or loss of supply voltage to the cooker. If in
doubt please contact your installer or a qualified repair
engineer.
Marks from mineral deposits from water or food can be
removed with a cleaning cream. However, tiny scratches
are not removable but will become less visible in time as
a result of cleaning.
Error code U400 is displayed
The cooker has been incorrectly connected. The control
will switch off after approximately 1 second and the
error code will be permanently displayed.
The oven fan is noisy
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
Grill not cooking properly
Are you using the pan and trivet supplied with the
cooker? Is the pan being used on the runners, not the
floor of the compartment? Is the grill tray pushed back
fully to the ‘back stop’ position?
Consult your installer or a qualified repair engineer.
Error code Er followed by a number is displayed
The appliance has developed an internal technical fault
that cannot be rectified by the user.
Consult your installer or a qualified repair engineer.
The knobs get hot when I use the oven or grill. Can I avoid
this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open. Make sure that the grill pan is pushed right back
to the ‘back stop’ when grilling.
The fuse blows or the RCD trips regularly
Please contact your installer or a qualified repair
engineer.
The cooker will not switch on
Has the wiring system in the house blown a fuse or
tripped an RCD?
Always grill with the grill compartment door open.
If there is an installation problem and I don’t get my
original installer to come back to fix it, who pays?
You do. Service organisations will charge for their callouts if they are correcting work carried out by your
original installer. Therefore, it’s in your own interest to
keep track of this installer so that you can contact them
as required.
Has the cooker been correctly connected to the mains
supply?
Has the child lock been activated? Please refer to the
child lock section for details of this function.
The induction hob is noisy
When using the induction hob there may be some
‘noise’ emitted from the pan. This is normal and may be
most noticeable when cooking on high power settings
or if 5 pans are used simultaneously. The type of pan
may also contribute to induction ‘noise’.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock so that the timed oven
continues to operate.
24
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous
oven. Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. Then adjust the settings according to
your own individual tastes.
Fig.6-1
ArtNo.324-0005 Oven light bulb
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specified in the section on ‘General Oven Tips’.
Fig.6-2
If you are cooking a large item, be prepared to turn it
round during cooking.
ArtNo.324-0007 Unscrewing the bulb cover
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held firmly
against the seal.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level, arrange for
your supplier to level it for you.
The timed oven is not coming on when turned on
manually
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply. Is the
cooker supply on at the isolator switch?
Has the time of day been set?
Is the key symbol [] showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake? Is the oven locked (see above)?
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be fitted by a service person.
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from most electrical stores. Ask for an Edison
screw fitting 15 W 230 V lamp, FOR OVENS (Fig.6-1). It
must be a special bulb, heat resistant to 300 °C.
Before removing the existing bulb, turn off the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.
Locate the bulb cover and unscrew it by turning it
counter-clockwise – it may be very stiff (Fig.6-2).
25
Taking care to protect your fingers with a glove in case
the bulb should shatter, unscrew the old bulb.
Fig.6-3
Screw in the new bulb clockwise and then screw the
bulb cover back on. Turn on the electricity supply and
check that the bulb now lights.
The oven door is misaligned
The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig.6-3). Loosen the
bottom hinge fixing screws and use the notch and a flat
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig.6-4).
ArtNo.320-0006 Oven door hinge adjustment 1
Effect of hinge adjustment – exagerrated for clarity
Fig.6-4
Retighten the hinge screws.
Centreline of hinge pin
ArtNo.320-0007 Oven door hinge adjustment 2
Oven door omitted for clarity
26
INSTALLATION
Check the appliance is electrically safe when you have finished.
7. Installation
You will need the following equipment to complete the
cooker installation satisfactorily:
Dear Installer
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
•
Multimeter (for electrical checks).
You will also need the following tools:
1. Steel tape measure
2. Cross-head screwdriver
3. Flat-bladed screwdriver
4. Spirit level
5. Pencil
6. Adjustable spanner
7. 3 mm and 4 mm Allen keys
8. 13 mm spanner or socket wrench
Installer’s Name
Installer’s Company
ArtNo.050-0011 - Installer information table
Installer’s Telephone Number
Checking the parts:
Grill pan and trivet
(standard model shown)
Flat oven shelves
Appliance Serial Number
ArtNo.330-0002 - Grill pan w handle
Safety Requirements and Regulations
Drop shelf
This cooker must be installed in accordance with
the relevant instructions in this booklet, with the
relevant national and local regulations, and with the
local electricity supply companies’ requirements.
Handyrack (some models)
nn
ArtNo.324-0003 Handyrack
The appliance must be installed in accordance with
nn
the regulations in force and only in a well ventilated
space.
Read the instructions before installing or using this
nn
appliance.
Roasting tin
Plinth (standard model shown)
Provision of Ventilation
This appliance is not connected to a combustion products
evacuation device. Therefore, particular attention must be
given to the relevant requirements regarding ventilation.
ArtNo.324-0004 Roasting tin
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
Splashback (Classic, Classic Deluxe
and Elan models)
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
ArtNo.421-0002 - Splashback
This appliance is designed for domestic cooking
nn
only. Use for any other purpose could invalidate any
warranty or liability claim.
27
Allen keys
INSTALLATION
Check the appliance is electrically safe when you have finished.
Positioning the Cooker
ArtNo.090-0028 - 90 cooker min spacing GENERIC
Fig.7-1
75 mm
min
650 mm
min
ºC
Fig.7-1 and Fig.7-2 show the minimum recommended
distance from the cooker to nearby surfaces.
75 mm
min
The cooker should not be placed on a base.
The top of the pan supports should be level with, or above,
any adjacent work surface. A gap of 75 mm should be left
between each side of the cooker ABOVE the hotplate level
and any adjacent vertical surface.
ºC
M
905 mm min
930 mm max
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
A minimum space of 650 mm is required between the top of
the hob and a horizontal combustible surface.
*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
Fig.7-2
1110 mm min*
**Any splashback must be fitted in accordance with the
manufacturers instructions. Allowance should be made for the
flue trim, which is fitted to the cooker hob.
410 mm min
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration. We cannot accept
responsibility for damage caused by normal use of the
cooker to any material that de-laminates or discolours at
temperatures less than 65 °C above room temperature.
**
ArtNo.110-0016 110 induction min positions above cooker
Fig.7-3
We recommend a gap of 1110 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
ArtNo.110-0009 - 110 induction door clearances
If the cooker is near a corner of the kitchen, a clearance of
130 mm is required to allow the oven doors to open (Fig.7-3).
The actual opening of the doors is slightly less, but this allows
for some protection of your hand as you open the door.
130 mm min
Moving the Cooker
On no account try and move the cooker while it is
nn
plugged into the electricity supply.
Fig.7-4
The cooker is very heavy, so take great care.
nn
We recommend two people manoeuvre the cooker. Make
sure that the floor covering is firmly fixed, or removed to
prevent it being disturbed when moving the cooker around.
To help you, there are two levelling rollers at the back and
two screw-down levelling feet at the front.
Remove the polystyrene base pack. From the front, tilt
the cooker backwards and remove the front half of the
polystyrene base (Fig.7-4). Repeat from the back and remove
the rear half of the polystyrene base.
28
INSTALLATION
Check the appliance is electrically safe when you have finished.
Lowering the Two Rear Rollers
Fig.7-5
To adjust the height of the rear of the cooker, first fit a 13 mm
spanner or socket wrench onto the hexagonal adjusting nut
(Fig.7-5).
Rotate the nut – clockwise to raise – counter-clockwise to
lower. Make 10 complete (360°) turns clockwise.
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the cardboard base tray. Open the
grill door and right-hand oven door so that you can get a
good grip on the bottom of the fascia panel as you move the
oven (Fig.7-6).
Fig.7-6
Carefully push the cooker backwards off the base tray.
Remove the base tray.
Position the cooker close to its final position, leaving just
enough space to get behind it (Fig.7-7).
DO NOT use the door handles or control knobs to
nn
manoeuvre the cooker.
ArtNo.010-0004 Moving the cooker
Repositioning the Cooker Following
Connection
Fig.7-7
If you need to move the cooker once it has been connected,
make sure it is switched off at the supply switch before
gripping under the fascia panel and lifting the front of the
cooker slightly (Fig.7-6). Check behind the cooker to make
sure that the electricity cable is not caught. As you progress,
always make sure that the cable has sufficient slack to allow
the cooker to move.
When you replace the cooker, check behind it again once
more to make sure that the electricity cable is not caught or
trapped.
Levelling the Cooker
Place the cooker in its intended position. Take care not
to twist it within the gap between the kitchen units, as
otherwise, damage may occur to the cooker or units.
There are two screw-down feet at the front and two levelling
rollers at the rear, which can be used to adjust the height and
level of the cooker.
It is recommended that you use a spirit level on a shelf in one
of the ovens to check for level.
29
INSTALLATION
Check the appliance is electrically safe when you have finished.
Electrical Connection
Fig.7-8
The cooker must be installed by a qualified electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
L
N
Current Operated Earth Leakage Breakers
The combined use of your induction cooker and other
domestic appliances may cause nuisance tripping, so we
recommend that the cooker is protected on an individual
RCD (Residual Current Device) or RCBO (Residual Current
Breaker with Overload).
10 mm² max
ArtNo.130-0010 Electrical connections single-phase6 mm² max
230 V ac 50 Hz
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
WARNING: THE APPLIANCE MUST BE EARTHED.
nn
Fig.7-9
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
L1
N
L3
L2
The cooker MUST NOT be connected to an ordinary
nn
domestic power point.
6 mm² max
3N ac
230/400 V 50 Hz
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect the
mains cable to the correct terminals for your electrical supply
type (Fig.7-8 and Fig.7-9). Check that the links are correctly
fitted and that the terminal screws are tight.
10 mm² max
Secure the mains cable using the cable clamp.
Final Checks
Hob Check
Check each cooking zone in turn. Be sure to use pans of the
correct size and material.
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Set the clock as described earlier, and then turn on the ovens.
Check the oven fans start to turn and that the ovens heat up.
30
INSTALLATION
Check the appliance is electrically safe when you have finished.
Final Fitting
Fig.7-10
Fitting the Handles and Handrail (depending on
model)
Remove the 4 mm Allen screws from the doors (Fig.7-10). Fit
the door handles and secure using the 4 mm screws.
ArtNo.215-0026 - Handle gaskets fixed
The handles should be above the fixings.
nn
Elan, Classic and Classic Deluxe only: Fit the plastic
blanking plugs to the fixing holes (Fig.7-11).
Fig.7-11
Remove the 4 mm Allen screws from the top corners of the
fascia (Fig.7-12). Fit the front handrail in position and secure
using the 4 mm screws.
Fitting the 1-piece Plinth
Loosen the three screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw. Twist
and fit each end keyhole over their respective screws. Tighten
the fixing screws (Fig.7-13).
ArtNo.215-0027 - Elan handle blanking plugs
Fig.7-12
Fitting the 2-piece Plinth (Classic Deluxe and
Professional Deluxe)
Fit the inner plinth to the bottom front of the cooker using
the 4 screws provided (Fig.7-14).
Art No 215-0028 - Handrail fascia fixings
Fit the outer plinth (2 screws, 1 each end) to the inner plinth.
The height of the outer plinth can be adjusted by sliding it up
or down via the slotted hole (Fig.7-15).
Fig.7-13
Fitting the Splashback (Classic, Classic Deluxe & Elan)
Position the splashback on the rear of the hotplate and secure
with the screws supplied.
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
ArtNo.350-0012 - Securing the plinth
Thank you.
Fig.7-14
ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)
Fig.7-15
ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)
Outer plinth
Inner plinth
31
Outer plinth fixing screw
8. Circuit Diagrams
ArtNo.090-0003 - Circuit diagram - 110 induction GENERIC
Circuit Diagram: Hob
INDUCTION UNIT
E
Earth
5
N(6) On Terminal Block
4
N(4) On Terminal Block
3
2
1
HOB
DISPLAY
w/br
w/br
L(2)
L(3)
On Terminal Block
1
INTERFACE
2 BOARD 5
3
4
w/br
w/br
1
2
w/br
5
3
4
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Colour
Code Description
1
Left-hand front element
2
Left-hand rear element
3
Right-hand rear element
4
Right-hand front element
5
Centre element
w/br White/brown
32
Circuit Diagram: Multi-function Oven (Elan)
b
F1
v
ArtNo.080-0049 110 Elan induction (oven) circuit diagram
bk
v
r
I
r
4
r
3
P3
2
A1 P2
1
v
2
P4
y
B1
P1
P095199
I
b 7
r
bk
bk
P1
v
P033458
B8
gr 8
y
bk
br
r
b
I
P2
1
v
gr
F2
P8 b
P7
b
P6 v
6
gr 5
P5
w 4
P4
y 3
P3
or 2
P2
r
P1
1
P028728
bk
bk
b br
P033458
w
I
y
w
w
b
r
b
B3
b
D2
b
w
B4
B5
b
H
gr
b
b
b
bk
H
b
b
G
br
v
br
A3
v
b
g/y
bk
br
br
r
v
P1
v
b
r
1
B2
g/y
r
v
D1 P2
b
br
A2
v
y
P3
2
P4
y
b
br
3
v
y
y
4
or
br
C
br
y
b
br
b
y
b
b
b
b
bk
b
bk
b
G
b
b
b
D3
or
B6
w
H
or
D4
b
r
b
b
B7
b
b
b
br
v
2
br
4
5
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
Code Description
Code Colour
Clock
b
Blue
D1
Right-hand oven front switch
br
Brown
Grill elements
D2
Right-hand oven thermostat
bk
Black
B1
Multi-function oven thermostat front switch
D3
Right-hand fan oven element
or
Orange
B2
Multi-function oven thermostat
D4
Right-hand oven fan
r
Red
B3
Multi-function oven top element (outer pr.)
F1
Cooling fan
v
Violet
B4
Multi-function oven top element (inner pr.)
F2
Oven light switch
w
White
B5
Multi-function fan element
G
Oven light(s)
y
Yellow
B6
Multi-function oven fan
H
Thermal cut-out
g/y
Green/yellow
B7
Multi-function base element
I
Neon
gr
Grey
B8
Multi-function oven function select switch
A1
Grill front switch
A2
Grill energy regulator
A3
C
33
Circuit Diagram: Multi-function Oven (Classic Deluxe & Professional Deluxe)
br
br
r
I
bk
C
I
B2a
b
br
br
y
bk
A2
bk
I
v
r
b
br
b
b
v
b
bk
b
br 4
P4
br
br 3
P3
br
bk 2
A1 P2
y
1
P1
r
br
br
bk
w
b
B3
B4
B5
H B7
b
b
r
gr 8
w
B6
w
y
o
o
bk
y
o
B2
w
w w y
6
5
P5
4
P4
3
P3
2
P2 y
P1 y
1
K
D2
P8
v
P7 r
P6 w
7
o
r
gr
b
b
b
F2
b
H
A3
v
B1
w
b
r
r
br
br
v
bk
v
F1
y 4
o 3
P038434
P3
br 2
D1 P2
v 1
P1
v
G
br b
v
b
o
bk
bk
br
D3
D4
br
br
br
br
P033458
b
P033458
w
P4
G
H
b b
b
b
b
b
br
br
b b b b bb b
L
N
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
A1
Grill front switch
A2
Grill energy regulator
A3
Code Description
C
Code Colour
Clock
b
Blue
D1
Right-hand oven front switch
br
Brown
Grill elements
D2
Right-hand oven thermostat
bk
Black
B1
Multi-function oven thermostat (Rapid
Heat)
D3
Right-hand fan oven element
or
Orange
B2
Multi-function oven switch
D4
Right-hand oven fan
r
Red
B2a
Multi-function oven thermostat front switch
F1
Cooling fan
v
Violet
B3
Multi-function base element
F2
Oven light switch
w
White
B4
Multi-function oven top element (outer pr.)
G
Oven light(s)
y
Yellow
B5
Multi-function oven top element (inner pr.)
H
Thermal cut-out
g/y
Green/yellow
B6
Multi-function fan element
I
Neon
gr
Grey
B7
Multi-function oven fan
34
Circuit Diagram: Conventional Oven (Classic, Toledo & Professional+)
J
r
br
bk
K
b
J
b
v
v
br
y
A2
r
B2
g/y
b
r
C
v
br
b
b
b
y
r
y
B3
B4
b
bk
4
P2
3
1
B1
2
w
B5
br
2
P2
A1
1
br
g/y
D2
br
r
v
P1
r
bk
y
w
y
5
P3
P038482
v
br
bk
br
v
br
w
br
br
A3
v
b
J
bk
br
b
b
v
br
bk
F
bk
bk
bk
2
P2
r
br
y
P1
D1
1
or
P095199
bk
b
b
H
b
b
bk
G2
v
P095199
v
G1
b
or
br
b
H
D4
br
b
b
2
D3
b
br
1
w
P1
4
6
b
br
br
br
br
bb
bb
bbb
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
Code Description
Code Colour
A1
Grill front switch
D3
Right-hand fan oven element
b
Blue
A2
Grill energy regulator
D4
Right-hand oven element
br
Brown
A3
Grill elements
Oven light switch
bk
Black
B1
Zoned oven front switch
G1
Left-hand oven light
or
Orange
B2
Zoned oven thermostat
G2
Right-hand oven light
r
Red
B3
Zoned oven browning element (inner pair)
H
Thermal cut-out
v
Violet
B4
Zoned oven top element (outer pair)
J
Neon
w
White
B5
Zoned oven base element
K
Cooling fan
y
Yellow
C
Clock
g/y
Green/yellow
D1
Right-hand oven front switch
gr
Grey
D2
Right-hand oven thermostat
F
35
9. Technical Data
DocNo.100-0003 - Technical data - IN 110 - GENERIC
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below the oven door opening.
COUNTRIES OF DESTINATION: GB, IE.
Connections
Electric
230 / 400 V 50 Hz
Dimensions
Elan
Classic Deluxe
Professional Deluxe
Overall height
min 905 mm max 930 mm
min 905 mm max 930 mm
min 905 mm max 930 mm
Overall width
1100 mm
1100 mm
1100 mm
597 mm (to fascia inc. splashback) 597 mm (to fascia inc. splashback)
Overall depth
595 mm (to fascia)
679 mm (over handles)
666 mm (over towel rail)
642 mm (over handles)
650 mm
650 mm
650 mm
Toledo
Classic
Professional+
Overall height
min 905 mm max 930 mm
min 905 mm max 930 mm
min 905 mm max 930 mm
Overall width
1100 mm
1100 mm
1100 mm
Minimum space above hotplate
596 mm (to fascia inc. splashback) 596 mm (to fascia inc. splashback)
Overall depth
654 mm (over handles)
657 mm (over towel rail)
642 mm (over handles)
650 mm
650 mm
650 mm
Minimum space above hotplate
See “Positioning the Cooker“.
Ratings
Max: 1.85 kW
Boost: 2.5 kW
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.15 kW
Boost: 2.0 kW
596 mm (to fascia)
Max: 1.85 kW
Boost: 2.5 kW
Max: 1.15 kW
Boost: 2.0 kW
36
Oven Efficiencies
Left-hand Oven
Ovens
Multi-function
Maximum output@ 230 V 50 Hz
Multi-function
(with Rapid Response)
Right-hand Oven
Conventional Forced Air Convection
2.5 kW
3.7 kW
2.2 kW
2.5 kW
Energy efficiency class on a scale of A (more
efficient) to G (less efficient)
A
A
A
A
Energy consumption based on standard load
0.95 kWh
0.95 kWh
0.99 kW
0.90 kWh
69
69
67
69
Large
Large
Large
Large
41 minutes
41 minutes
40 minutes
41 minutes
1400 cm²
1400 cm²
1400 cm²
1400 cm²
Usable volume (litres)
Size
Time to cook standard load
Surface area of the grill
Grill
2.3 kW
Maximum total electrical load at 230 V (approximate including oven lights, oven fan, etc.)
Multi-function oven variant: 14.82 kW
Multi-function oven (with rapid response) variant: 16.02 kW
Conventional oven variant: 14.52 kW.
37
Notes
38
For warranty compliance, the requirements are
that the appliance:
Name of Appliance & Colour*
•
Has been correctly installed in accordance with current
legislation, relevant British and European Standards and Codes
of Practice, by a suitably competent person registered with
Gas Safe or equivalent body and, where applicable, a qualified
electrician.
•
Has been used solely for domestic cooking purposes.
•
If in use in the UK*, has not been taken abroad as a personal
export. (In the Republic of Ireland conditions may vary, so
consult your retailer.)
•
Is not second-hand or a refurbished appliance. The
manufacturer’s warranty is not transferable.
•
Has not been subject to misuse, accidental damage or
modification, and has not deteriorated due to normal
domestic wear and tear, and the manufacturer’s
recommendations concerning cleaning materials have been
followed.
•
Has not been repaired by persons or organisations other than
those authorised to act on behalf of AGA Rangemaster.
Appliance Serial Number*
Natural Gas
LP Gas
Dual Fuel
Electric
Fuel Type*
Retailer’s Name & Address
Date of Purchase
Exceptions:
Installer’s Name & Address
Installer’s Telephone Number
•
Items not included under the free 1 year guarantee include
pan supports, griddles, wok rings, baking trays, grill pans,
trivets, filters, light bulbs and other consumable accessories.
•
Any damage caused other than through normal use.
•
Breakdowns associated with cooking spillage.
•
Cosmetic deterioration deemed to be normal wear and tear.
This warranty is in addition to your Statutory Rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
Date of Installation
OUT OF WARRANTY
Service work should only be carried out by technically competent
and suitably qualified personnel.
* This information is on the appliance data badge - look in the appliance
instructions to find out where the data badge is located.
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please
telephone 0870 789 5107.
CONSUMER SERVICE LINES OPEN:
For your own safety, always make sure that work is carried out by
a Gas Safe registered engineer for gas appliances or an approved
electrician for electrical models.
For a competitive quote and to arrange for a Rangemaster approved
engineer to attend, call Consumer Services on: 0870 7895107.
SPARE PARTS
Monday to Thursday 8am–6pm
Friday 8am–5pm
Saturday 9am–1pm
To maintain optimum and safe performance, we recommend that
only genuine Rangemaster spare parts are used. These are available
from most major spares stockists, including ourselves.
WARRANTY
Contact Consumer Services on 0870 7895107, who will be happy to
help.
Your manufacturer warranty covers goods of our own brand for
defective workmanship and materials for a period of 1 year from the
date of purchase. This warranty covers mechanical breakdown and
proven cosmetic and manufacturing defects.
STANDARDS
You will receive an additional FREE full 12 months guarantee by
registering your purchase using the FREEPOST form provided.
Alternatively, call free on 0800 587 5747, quoting reference
RMGX57A, or register online at www.rangemaster.co.uk.
Any damage, blemishes or chips identified upon receipt of the
product must be reported within 90 days – proof of purchase
may be required to establish validity. Scratches on the surface of
ceramic hobs must be reported within 14 days. Scratches caused
by usage are not covered. Accidental damage is not covered by the
manufacturer’s warranty.
Rangemaster cookers are designed and manufactured to a
recognised international quality standard, which meets the
requirements of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001
for continually improving environmental procedures.
Rangemaster cookers comply with the essential requirements of the
appropriate European Directives, and carry the CE mark.
ALSO PART OF THE RANGEMASTER COLLECTION...
Refrigeration
Built-in Cooking
Dishwashing
Sinks & Taps
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
England
Tel: +44 (0) 1926 457400
Fax: +44 (0)1926 450526
E-mail: consumers@rangemaster.co.uk
Consumer Services Tel: +44 (0) 870 7895107
www.rangemaster.co.uk
Britain’s No.1 Range Cooker
For ROI Enquiries Tel: 1850 302 502
Search Rangemaster UK
Registered in England and Wales. Registration No. 354715 Registered Office: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG
Rangemaster continuously seeks improvements in specification, design and production of products and thus, alterations take place
periodically. Whilst every effort is made to produce up-to-date literature, this booklet should not be regarded as an infallible guide to
current specification, nor does it constitute an offer for the sale of any particular appliance.
Download PDF

advertising