Conexant | HCF V.90 | User`s guide | Conexant HCF V.90 User`s guide

56K USB Modem
Conexant HCF V.90
User’s Guide
Conexant HCF V.90 56K USB Modem
User’s Guide
FCC Requirements
This equipment complies with Part 68 of the FCC Rules. On the bottom of this
equipment is a label that contains, among other information, the FCC Registration Number and
Ringer Equivalence Number (REN) for this equipment.
IF REQUESTED. THIS
INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
The REN is useful to determine the quantity of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is called. In
most, but not all areas the sum of the REN’s of all devices connected to one line should not
exceed five (5.0). To be certain of the number of devices you may connect to your line. as
determined by the REN. Yo u should contact your local telephone company to determine the
maximum REN of the area you are calling from. If your telephone equipment causes harm to
the telephone network. The telephone company may discontinue your service temporally. If
possible, they will notify you in advance. But if the advanced notice is failed , you will be
notified as soon as possible. You will be informed of your right to file a complaint with the
FCC.
Your telephone company may change in its facilities, equipment, operations or
procedures that could affect the proper functions of your equipment. If this occurs, you will be
notified in advance to give you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the following
address and phone number for information on obtaining service or repairs. The telephone
company may ask you to disconnect this equipment from the network until the problem is
solved or until that the equipment is not detected malfunctioning. This equipment may not be
used on coin service provided by the telephone company. Connection to party lines is subject to
state Tariffs.
Federal Communications Commission
Radio Frequency Interference Statement .
Note: This equipment has been tested and found to comply with the limitation for a class B
digital device pursuant to Part 15 of the FCC Rules. These restrictions are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used in accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determine by tuning the equipment off and on, the user is
suggested to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected. Consult the dealer or an experienced radio TV technician for help.
Notices:
(1) The changes or modifications not expressly approved by the party responsible for
Compliance could void the user’s authority to operate the equipment.
(2) Shielded interface cables and AC power cord if any must be used in order to comply with
the emission limits.
2
Conexant HCF V.90 56K USB Modem
User’s Guide
Notices to Australian users:
The modem card must only be used in a data terminal equipment (DTE) e.g. computer, that has
a screw down cover (lid). As unsafe voltages (TNV) exist on the modem card, disconnect the
modem card from the telephone line while the cover (lid) of the DTE (computer) is removed.
Installation of the modem card in a DTE (computer) which does not require a tool to open the
cover (lid) will render the permit void.
Disconnect the telephone line before opening the cover (lid) of the DTE (computer). Do not
connect the customer equipment to the telephone line while the cover (lid) of the DTE
(computer) is open.
WARNING
ONLY CONNECT EQUIPMENT WITH A TELECOMMUNICATIONS
COMPLIANCE LABEL
WARNING
FOR SAFETY REASONS, ONLY CONNECT EQUIPMENT WITH A
TELECOMMUNICATIOS COMPLIANCE LABEL. THIS INCLUDES
CUSTOMER EQUIPMENT PREVIOUSLY LABELLED
PERMITTED OR CERTIFIED.
Modems connected to the Australian telecommunications network must be marked in
accordance with the Labeling Notice. This modem has been specifically configured to ensure
compliance with the ACA Standards. Do not adjust your modem or software outside the values
indicated as below. To do so would result in your modem being operated in a non-compliant
manner.
Modem Commands:
Command
Default
Permissible Range
ATA
Do not use
ATB
B0
Do not set to B1
AT&G
&G0
&G2
AT&P
&P0
&P1
ATSn
see table below
S register
Default
Permissible Range
S6
2
2 to 6
Call Attempts/Retries:
Applications software shall be configured so that no more than 3 attempts are made to
establish a connection to a given number (Note: if the modem can detect service tones, up to
10 attempts can be made). If the call sequence is unsuccessful, there shall be a delay of at least
30 minutes before attempting to call the number again.
Failure to set the modem and any application software used with the modem, to the values
shown as above will result in the modem being operated in a non-compliant manner.
Consequently, this would be in violation of the Labeling Notice for this equipment, and the
Telecommunications ACT 1997 prescribes penalties for the connection of non-compliant
equipment .
3
Conexant HCF V.90 56K USB Modem
User’s Guide
TABLE OF CONTENTS
Chapter 1 Introduction ......................................................5
1.1 Introduction.............................................................................................................................5
1.2 Features ....................................................................................................................................5
1.3 What’s in the Package .............................................................................................................5
Chapter 2 Specifications...................................................6
2.1 Specifications...........................................................................................................................6
2.2 System Requirements .............................................................................................................6
Chapter 3 Hardware Installation.......................................7
Chapter 4 Driver Installation .............................................8
4.1 Installing Windows 98............................................................................................................8
4.2 Installing Windows 2000......................................................................................................11
Chapter 5 Diagnostics.....................................................14
5.1 Diagnostics in Windows 98 .................................................................................................14
5.2 Diagnostics in Windows 2000.............................................................................................16
Chapter 6 Uninstalling ....................................................18
6.1 Uninstalling in Windows 98 ................................................................................................18
6.2 Uninstalling in Windows 2000............................................................................................21
4
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 1 Introduction
1.1 Introduction
Thank you for choosing this HCF V.90 56K USB Modem. It is not only the most
cost-effective solution to connect your PC to the Internet, but also increase the usage of the
CPU and decrease the cost of ownership. It reduces the time and pain during installation
procedure. All you have to do are just plug & play and inserting the CD-ROM Disk, even
that you don’t need to turn off the power of your PC. Because it’s a really USB device so
it supports the fully HOT plug and play function. Furthermore, it follows the K56Flex
/V.90 Standard, you can access the Internet at Max. rate 56K bps (It depends on the line
condition and the ISP you connected to). If you have a PC system with USB interface, we
strongly recommend you to take this modem as your best choice.
1.2 Features
USB interface, HOT plug and play, easy to install
ITU 56K V.90 Standard
Windows 98 /Windows 2000 compatible
No Extra Power Needs & Low power consumption
Host-Controlled Modem
User Friendly
1.3 What’s in the Package
Modem Unit
CD-ROM Disk (Comprises Application Software, Modem Drivers & User’s Manual)
Telephone cord
Quick Guide for Installing Modem Drivers
5
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 2 Specifications
2.1 Specifications
Computer Interface USB V1.1
Line Interface
RJ-11 for POTS line
Data Protocols
V.90, K56flex, V.34, V.32bis, V.32, V.22bis, V.22, V.23, V.21, Bell
212A and 103
Data Sp eed
56k, 54k, 52k, 50k, 48k, 46k, 44k, 42k, 40k, 38k, 36k, 34k, 33.6k,
31.2k, 28.8k, 26.4k, 24k, 21.6k, 19.2k, 16.8k, 14.4k, 12k, 9600,
7200, 4800, 2400, 1200, 300
Data Compression V.42bis, MNP 5
Error Correction
V.42 LAPM, MNP 2,3,4
Fax Protocols
Group 3 Compatible, Class 1 fax: V.17, V.29, V.27ter, V.21 ch 2
Fax Speed
14.4k, 12k, 9600, 7200, 4800, 2400, 300
General
Standard AT commands, V.8 and Automode, Caller ID, Virtual DTE,
V.80 Virtual UART (115.2kbps), DTMF detection and generation,
ADPCM, Answering machine (voice), OnNow Power Management,
Wake-up on ring , Distinctive ring for data/fax/voice, World wide
country support
Power Consumption below 700mW
2.2 System Requirements
CPU
: Pentium 200MHz or greater
RAM
: 16Mbyte RAM or more
Interface : USB port
HDD
: 2MB free space or above
Telecom Requirement : 1 POTS line
Operation system : Windows 98 , Windows 2000
6
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 3 Hardware Installation
1.
Plug the connector of the USB Modem into the USB port of your PC.
2.
Plug one end of telephone cord into the modem’s “LINE” jack, which is shown on
the modem’s bracket labeled “LINE”.
3.
Insert the other end of the cord into the telephone wall socket.
4.
Enable the USB port option in the BIOS setup of your computer.
7
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 4 Software Installation
Power on your computer and modem and then start Windows 98/2000.
Windows 98/2000 will detect the modem automatically.
4.1 Windows 98
1.
When you see the message of V.90 modem with USB interface appearing,
insert the driver CD came with the modem. Then click Next to search for the
driver.
2.
Select Search for a suitable driver for your device [Recommended] and
click Next to continue.
8
Conexant HCF V.90 56K USB Modem
User’s Guide
3.
Select Specify a location, then type in I:\Hcf_Usb\Win98 (I is the letter of
the CD-ROM drive) or use Browse to search the location, and click Next to
start the search.
4.
Windows has found the location of the driver for Conexant USB HCF V.90
Data, Fax, Voice Modem, click Next to start the installation.
9
Conexant HCF V.90 56K USB Modem
5.
User’s Guide
This installation has been done; click Finish to end this procedure.
10
Conexant HCF V.90 56K USB Modem
User’s Guide
4.2 Installing Windows 2000
1.
Windows will detect the modem automatic; please insert the driver CD
supplied and clicks Next.
2.
Select Search for a suitable driver for my device [recommended], then
click Next.
11
Conexant HCF V.90 56K USB Modem
User’s Guide
3.
Select Specify a location, then click Next.
4.
Please type I:\Hcf_Usb\Win2K or use Browse… to find the driver directly,
then click OK (I is the letter of CD-ROM drive).
5.
Windows will found a driver for this device, then click Next.
12
Conexant HCF V.90 56K USB Modem
6.
Click Yes to continue.
7.
Click Finish to end this procedure.
User’s Guide
13
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 5 Diagnostics
5.1 Diagnostics in Windows 98
1.
Move your cursor as following sequence Start / Settings / Control Panel, and
double-click on the Modems icon.
2.
To test the modem by clicking on the Diagnostics tab. Then select the COM
Port where Conexant HCF V.90 Data Fax Voice USB is setting and click
More Info… to start the test.
14
Conexant HCF V.90 56K USB Modem
3.
User’s Guide
If your modem is responding to AT commands and functioning correctly, it means
that your modem is working properly. Click OK to end this procedure.
15
Conexant HCF V.90 56K USB Modem
User’s Guide
5.2 Diagnostics in Windows 2000
1.
Move your cursor as following sequence Start\Settings\Control Panel.
Then double-click on the Phone and Modem Options icon.
2.
Click on the Modems tab, then select Conexant HCF V90 Data Fax Voice
USB Modem and click Properties.
16
Conexant HCF V.90 56K USB Modem
User’s Guide
3.
Click on the Diagnostics tab. To test the modem by clicking Query Modem.
4.
If your modem is responding to AT commands and functioning correctly, it
means that your modem is working properly. Click OK to end this
procedure.
17
Conexant HCF V.90 56K USB Modem
User’s Guide
Chapter 6 Uninstalling
6.1 Uninstalling in Windows 98
1.
Move your cursor as following sequence Start / Settings / Control Panel and
Double-click on the Add/Remove programs icon.
18
Conexant HCF V.90 56K USB Modem
User’s Guide
2.
Select Conexant HCF USB Modem and click on the Add/Remove…
button.
3.
Click Yes to remove the modem.
19
Conexant HCF V.90 56K USB Modem
4.
User’s Guide
Click OK to end this procedure.
20
Conexant HCF V.90 56K USB Modem
User’s Guide
6.2 Uninstall in Windows 2000
1.
Move your cursor as following sequence Start \ Settings \ Control Panel.
Then double-click on the Add/Remove Hardware icon.
2.
Click Next to continues.
21
Conexant HCF V.90 56K USB Modem
User’s Guide
3.
Select Uninstall/Unplug a device, then click Next.
4.
Select Uninstall a device and click Next to continue
22
Conexant HCF V.90 56K USB Modem
User’s Guide
5.
Select Conexant HCF V90 Data Fax Voice USB Modem, then click Next
to continue.
6.
Select YES, I want to uninstall this device, then click Next to continue.
23
Conexant HCF V.90 56K USB Modem
7.
User’s Guide
Click Finish to end this procedure.
24
Download PDF

advertising