CAS | NC-200 | Owner`s manual | CAS NC-200 Owner`s manual

Crane Scale
NC Series
OWNER’S MANUAL
CONTENTS
PRECAUTIONS
PREFACE
NAMES AND FUNCTIONS
4
6
6
1. OVERALL VIEW
2. DISPLAY
3. KEY FUNCTIONS
6
6
7
OPERATIONS
7
1. POWER ON
2. ZERO OPERATION
3. TARE OPERATION
4. UNIT CONVERSIONS
7
7
8
9
ERROR MESSAGES
9
1. ERROR 1
2. ERROR 3
3. OVER LOAD
4. ERROR BEEP
9
9
10
10
THE PROGRAMS
10
1. TO SELECT MOTION BAND
2. TO SELECT DIGITAL FILTER
3. TO SELECT AUTO-POWER OFF INTERVAL
4. TO SET E.L. ON OR OFF
10
11
11
12
BATTERY OPERATION
13
1. CHARGE
2. BATTERY OPERATING TIME
3. LOW BATTERY("BAT.") SIGNAL
13
14
14
REMOTE CONTROL
14
1. REMOTE CONTROLLER OPERATION
2. REPLACING BATTERY IN REMOTE CONTROLLER
14
14
ASSEMBLE AND DISASSEMBLY
SPECIFICATIONS
15
16
PRECAUTIONS
Attention
Warning
Do not disassemble the scale.
When any damage or
defect occurs, contact
your CAS authorized
dealer immediately for
proper repair.
Do not overload beyond the maximum
weight limit.
Scale must be grounded to minimize
electricity static. This will minimize
defect or electric shock.
For consistent and accurate reading,
maintain periodical check by your
CAS authorized dealer.
Avoid sudden shock to the scale.
Internal mechanism could be damaged.
Do not pull the plug by its cord when
unplugging. Damaged cord could cause
electric shock or fire.
To prevent from fire occurring, Do not
place or use the scale near
flammable or corrosive
gas.
To reduce electric shock or incorrect
reading, Do not spill water on the scale
or place it in humid condition.
Place the scale on firm and temperature
consistent environment.
Keep the scale away from other
electromagnetic generating devices.
This may interfere with accurate
reading.
Avoid placing the scale near heater
or in direct sunlight.
Use proper Adapter. Incorrect adapter
could damage the scale.
Insert plug firmly to wall outlet to
prevent electric shock.
4
Take the battery out when scale is not in
use for long time. Leakage from the
batteries is hazardous.
5
PREFACE
Thank you for purchasing our CAS NC SERIES.
These series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your specialty departments can enjoy these
high quality reliable CAS products.
We believe that your needs will be satisfied and you will have proper reliability.
This manual will help you with proper operation and care of the CASTON .
Please keep it handy for future reference.
ZERO LAMP : It shows zero state. When the scale is loaded,
the lamp will be turned off.
TARE LAMP : It is lit when the tare weight entered.
BAT. LAMP : It is lit when battery needs to be exchanged.
EXTERNAL POWER OPERATION LAMP : It is lit when DC 12V
adaptor supplies power to scale.
RECHARGE END LAMP : It is lit when being recharged and turn off
when recharge finishes.
3. KEY FUNCTIONS
KEYS
NAMES AND FUNCTIONS
Turns power on or off.
1. OVERALL VIEW
FRONT VIEW
FUNCTIONS
REAR VIEW
ZERO
Zero the scale when the zero point is drifted.
TARE
Subtracts tare weight gross weight.
JOINT RING ASSY
DISPLAY WINDOW
SEALING
BOLT
NAME
PLATE
ON/OFF
S/W
KEY BOARD
HOOK
Select kg or lb.(Capture and display weight)
SPEC PLATE
JACK
RUBBER
ON
OFF
OPERATIONS
1. POWER ON
Press "ON/OFF" key.
2. ZERO OPERATION
2. DISPLAY
6
Press "ZERO" key when the zero point is drifted.
7
3. TARE OPERATION
4. UNIT CONVERSIONS
Load tare on the hook.
Place an item to be weight on the hook.(GRAM MODE)
Press "TARE" key.
"0" is displayed, and the tare is subtracted.
Remove weight on the hook.
Press "kg/lb" key.(POUND MODE)
Place an item to be weight on the hook.
lb
Remove tare on the hook.
ERROR MESSAGES
1. ERROR 1
Over-range error of an initial zero.
Make the hook empty.
Press "TARE" key.
The tare weight is cleared appers in the display window.
2. ERROR 3
The scale needs calibration.
8
9
3. OVER LOAD
When a load is over the limit weight
of a scale.
LIMIT WEIGHT=CAPACITY+6D
(See TABLE 1)
0
1
2
4. ERROR BEEP
When pressing "ZERO" key while TARE is used.
When pressing "ZERO" or "TARE" key while a scale is not stable.
When pressing "ZERO" key while ZERO RANGE OVER happens.
1D
5D
10D
TABLE 1
(* D=INTERVAL)
2. TO SELECT DIGITAL FILTER
DIGITAL FILTER IS THE FUNCTION THAT MAKES DISPLAY
SPEED FASTER OR SLOWER ON THE USING CONDITION.
THE HIGHER VALUE IS THE LOWER SPEED.
THE PROGRAMS
Turn power on pressing "ZERO" key.
is displayed.
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
(See TABLE 2)
is displayed.
Press "kg/lb" (HOLD)key.
1. TO SELECT MOTION BAND
0
1
NONE
FASTER
7
SLOWER
TABLE 2
MOTION BAND IS THE RANGE THAT MAKES A SCALE HANDLE
AN UNSTABLE WEIGHT AS A STABLE WEIGHT IN.
3. TO SELECT AUTO-POWER OFF INTERVAL
is displayed.
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
10
AUTO POWER OFF IS THE FUNCTION THAT MAKES POWER
DOWN WHEN A SCALE IS NOT OPERATED BY USER TO SAVE
BATTERY POWER.
11
BATTERY OPERATION
is displayed.
1. CHARGE
To increase the number, press "ZERO" key.
To set this entry and go to the next, press "kg/lb"(HOLD) key.
(See TABLE 3)
0
1
NONE
3 min
2
3
6 min
9 min
The rechargeable battery located inside the NC-series scale must be
charged using the voltage which don't exceed 10% of the voltage
indicated on the adapter.
If the voltage for charge exceed the above limit, the battery would
be damaged.
Check if an output voltage is DC 12V 1.5A.
Remove ADAPTOR JACK COVER of REAR PANEL and connect
adaptor with an scale like the following figure.
TABLE 3
4. TO SET E.L. ON OR OFF
E.L BACK LIGHT IS THE FUNCTION THAT MAKES THE
DISPLAY PANEL VISIBLE IN THE DARK BY LIGHTING
ELECTRIC LUMINANCE DEVICE.
(See TABLE 3)
0
1
2
3
OFF always
ON weighing and stable
ON weighing
ON always
TABLE 4
Press "kg/lb"(HOLD) key.
The scale returns to NORMAL MODE.
When an adaptor is linked with an scale, RED LAMP and
GREEN LAMP are ON.
Charging method.
Quick charge : Charge the battery until the green lamp is ON.
(Quick charging time : approximately 2 hours)
Standard charging method : Charge the battery for about 6 hours
after the green lamp is ON.
Note : If you use the quick charge, the battery is not charged fully.
(charged to the 70% of full charge)
To charge fully, use the standard charge.
12
13
2. BATTERY OPERATING TIME
The discharge time is dependent on the charging method and
power source.
In generally, if you use the battery continuously, the discharge
time is as follows.
with E.L. 16~22hours.
without E.L. 37~50hours.
Caused by repeated use, the discharge time can be decreased.
If the scale is not used for long time after charging the battery,
the discharge time is decreased. To restore the discharge time,
repeat the procedure of charge and discharge(if battery is
discharged the "BAT" lamp on the LCD will be displayed) for
2 or 3 times.
NOTE ON REPLACING BATTERIES.
Place batteries in correct polarity(+)(-)direction.
Do not use new batteries with the used.
ASSEMBLE AND DISASSEMBLY
DEVICE PIN
3. LOW BATTERY("BAT.") SIGNAL
To protect over-discharge of BATTERY, "BAT" LAMP is lit when
battery has to be charged.
A scale turns power off automatically an fixed period after "BAT"
is ON.
LOAD PIN
HOOK
REMOTE CONTROL
1. REMOTE CONTROLLER OPERATION
"ON/OFF" key : Power ON/OFF.
"ZERO" key : Make the scale stable to "0" while the zero point is drifted.
"TARE" key : Store the tare weight.
"kg/lb" key : Select kg or lb mode.
"HOLD" key : Capture and display weight.
OPERATION LAMP : Blinks once when keys are pressed.
2. REPLACING BATTERY IN REMOTE CONTROLLER
BATTERY SPEC.
VOLTAGE : 1.5V 2
SIZE : AA SIZE (14.5 50.5m/m)
BATTERY
14
15
SPECIFICATIONS
MODEL
NC-100 NC-200
MAXIMUM CAPACITY
100 kg
(200 lb)
INTERVAL
0.05kg 0.1kg
(0.02lb) (0.2lb)
FUNCTION
DISPLAY COLUMN
DISPLAY TYPE
DISPLAY DESIGNATORS
MAX TARE
WEIGHING TYPE
NC-500
200 kg
500 kg
(400 lb) (1250 lb)
0.2kg
(0.5lb)
NC-1
100 lb
(40kg)
250 lb 1000 lb
(125kg) (400kg)
0.05lb
0.1lb
0.5lb
(0.02kg) (0.05kg) (0.2kg)
ON /OFF, TARE, ZERO, kg/lb CONVERTING(HOLD)
5 DIGIT
L.C.D TYPE
ZERO, TARE, BAT.
FULL TARE
LOAD CELL TYPE
OPERATING TEMPERATURE
-10°C ~ +40°C
OPERATING POWER
DC 12V (1.5A)
POWER SOURCE
16
MEMO
AC 110 /120 / 220 / 240 V, 50 / 60Hz
POWER CONSUMPTION
0.25W
NET WEIGHT
5.5kg
17
MEMO
18
Download PDF

advertising