BenQ | 211c | Universal UR2-211 Remote Control

Operating Manual
For Easy Clicker
UR2-211
1 Introduction
3 Button Functions
This remote control is designed
to operate most Digital, Analog
Cable boxes, IPTV set top boxes
and TVs.
2 Replacing Batteries
Before you program or operate the
remote control, you must install
two new AA alkaline batteries.
STEP2 Point the remote at the
component and press and
hold the [DEVICE] key for 3
seconds until the Device LED
blinks off and turns back on.
Continue holding the [DEVICE]
key and press the numberkeys,
one at a time, starting with 1,
then2, 3...0. Stop pressing
the number keys when the
device turns off.
STEP1 Remove the battery compartment cover from the
back of your remote control.
STEP3 Release the [DEVICE] key to
save the code. The Device
LED will blink twice to
confirm the code is stored.
STEP2 Check battery polarity
carefully, and install the
batteries as shown in the
illustration below.
Repeat the steps above for all
components(CBL, TV).
STEP3 Replace the battery compartment cover.
B. Manual Programming
The remote control can be programmed
by entering a three-digit code number
that corresponds to particular brands
and models of equipment. The threedigit code numbers are listed in the
code tables sections of this instruction
manual.
STEP1 Turn on the equipment that
you want the remote control to operate (Cable Box or
TV).
4 Programming the Remote Control
*Note : In this section, when you are instructed to press a [DEVICE] button, that means you should press either
the CBL or TV button, depending on which device you are programming the remote to operate.
A. Quick Set-Up Method
Universal Remote Control, Inc.
www.universalremote.com
OCE-0082E Rev 02 (02/14/12)
(Refer to the Section 5 Quick Set-up table of codes)
STEP1 Turn on the equipment you want to program. To program your TV, turn on the TV.
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The corresponding device
LED will turn on indicating
that it is ready to be programmed. The LED will remain
on for 30 seconds. The next
step must be entered while
the LED is on.
STEP3 Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your
brand from the code tables.
If there are more than one
three-digit number listed for
your brand, try one code
number at a time until your
equipment turns off.
STEP2 Press the [DEVICE] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The device LED will turn on
indicating that it is ready to
be programmed. The LED
will remain on for 30 seconds.
The next step must be entered while the LED is on.
*Note: You can verify that you have
selected the correct code by
pressing the [POWER] button.
The equipment should turn
back on. Then try all of the
functions on the remote
control (i.e. volume, mute,
etc.) to ensure you have the
correct code. If any of the
functions do not operate as
they should, repeat the
instructions from STEP 3
above using the next three
digit code number from the
brand list.
STEP3 Press the [CH ] or [CH ]
button one at a time or keep
it pressed. The remote will
emit a series of Power
ON/OFF code signals. Release
the [CH ] or [CH ] button
as soon as the equipment
turns off.
STEP4 Store the three-digit code
by pressing the same
[DEVICE] button once again.
The device LED will blink
twice to confirm that the
code has been stored.
C. Auto Search Method
If none of the three digit code numbers
assigned to your brand of equipment
works, or the code table does not list
your brand, you can use the Auto
Search Method to find the correct
three-digit code number for your
equipment by following steps:
STEP1 Turn on the equipment that
you want the remote control
to operate (Cable Box or TV).
*Note: You can verify that you have
selected the correct code by
pressing the [POWER]
button. The equipment
should turn back on. Then
try all of the functions on
the remote control (i.e.
volume, mute, etc.) to ensure
you have the correct code. If
any of the functions do not
operate as they should,
repeat the instructions from
STEP 3 above to continue
the Auto Search Method.
STEP4 Press the same [DEVICE]
button to store the code.
The Device LED will blink
twice to confirm that the
code has been stored.
D. Pr ogramming the All Of f
Button
This allows you to program the All Off
button so it can send up to two power
On/Off commands with one button
press.
STEP1 Press the [CBL] button.
STEP2 Press the [All OFF] button
and the [OK/SEL] button
simultaneously for 3 seconds.
The [CBL] button will turn
on for 30 seconds.
STEP3 Press the first [Device] button
you want to store in the
[ALL OFF] button and then
the [POWER] button. Repeat
this for other Device until
you have stored all the
desired power commands
into the [ALL OFF] button.
STEP4 Press the [CH ] button to
save the power commands
you stored. The [CBL]
button will blink twice to
confirm the Device have
been saved.
E. Programming for On Demand
Button
The On Demand Button can be programmed
to act as a ‘Macro’ or Favorite Channel
button in CABLE mode. This allows
you to program up to five 2-digit
channels, four 3-digit channels or
three 4-digit channels that can be
accessed with one button press.
STEP1 Press the [CBL] button to
select the CBL mode.
STEP2 Press the [On Demand Button]
button and [OK/SEL] button
simultaneously for 3 seconds.
The [CBL] button will turn on
for 30 seconds.
STEP3 Enter the the 2, 3 or 4-digit
code for the channel you
want programmed first (for
example, 007) using the
Number Pad, then press the
[FAV] button. Then enter the
code for the next channel
(for example, 050), then
press the [FAV] button.
Repeat this process for the
third channel. The [CBL]
button will blink once for
each channel entered.
STEP4 Press the [CH ] button to
store the channels that
were selected. The [CBL]
button will blink twice to
confirm the storage of
commands.
F. Programming Volume
Control
By default, the VOL+, VOL- and MUTE
keys operate through your TV. If you
would like those keys to operate
those functions on a different device,
follow these steps.
STEP1 Press the [OK/SEL] button and
[CBL] button simultaneously
for 3 seconds. The device LED
will turn on for 30 seconds.
The next step must be
performed while the LED is on.
STEP2 Press the [VOL+] button.
The device LED will blink.
STEP3 Press the [DEVICE] button
corresponding to the device
that you would like the
volume and mute buttons to
control. The device LED will
blink twice to confirm the
programming.
*Note: If you wish to have the
volume and mute keys
operate your Cable Box,
press the [CBL] button in
Step 3.
5 Quick Set-up Code Tables
CBL
Quick Number
0
1
G. Pr ogramming Channel
Control
2
3
4
5
6
7
8
9
By default, the CH , CH keys operate
through your Cable Box. If you would like
those keys to operate those functions on
a different device, follow these steps.
STEP1 Press the [OK/SEL] button
and [CBL] button simultaneously
for 3 seconds. The device
LED will turn on for 30
seconds. The next step
must be performed while
the LED is on.
STEP2 Press the [VOL-] button. The
device LED will blink.
STEP3 Press [TV] button. The
device LED will blink twice
to confirm the programming.
*Note: If you wish to have the
channel keys operate your
Cable Box, press the [CBL]
button instead of the [TV]
button in Step 3.
H. Memory Lock System.
This remote control is designed to
retain programmed memory for 10
years — even after batteries are
removed from the remote control.
For additional information about your
remote control, go to
www.universalremote.com
Manufacturer/Brand
PACE
SCIENTIFIC ATLANTA/CISCO
PACE, SAMSUNG
MOTOROLA
AMINO 130/530
AT&T/SCIENTIFIC ATLANTA IPTV
CISCO IPTV
ADB
MOXI
AMINO 140/540
MOTOROLA IPTV
TV
Quick Number
0
1
2
3
4
5
6
7
8
9
Manufacturer/Brand
SANYO
SONY
SAMSUNG
LG
TOSHIBA
PANASONIC
PHILIPS
HITACHI
SHARP
VIZIO
6 Set-up Code Tables
CBL-IPTV
Manufacturer/Brand
ADB
AMINO
AT&T
CISCO
COMCAST
ENTONE
MYRIO
MOTOROLA
NOW TV
PACE
SCIENTIFIC ATLANTA
WEGENER
Set-Up Code Number
254 255 315 259
249 256 257 260 261
251
002 251 316
002
155 258
254 255
253
314
002
251
250
CBL-CABLE Converters
Manufacturer/Brand
SCIENTIFIC ATLANTA
PACE
MOTOROLA
CHANNEL MASTER
CISCO
DIGITAL STREAM
EVOLUTION
Set-Up Code Number
003
001
001
006
003 005
580
189
CBL-CABLE Converters
TV
Manufacturer/Brand
Manufacturer/Brand
Set-Up Code Number
DIGITAL LIFESTYLE
DIGITAL PROJECTION
DIGITAL RESEARCH
DIGITRON
DISNEY
DREAMVISION
DUMONT
DURABRAND
DWIN
DYNASTY
DYNATECH
DYNEX
ELECTROBAND
ELECTROGRAPH
ELECTROHOME
ELEMENT
EMERSON
163
570
258
101
096
090
004 073
168
131 132 161
043
062 238
096
001
220
024 076 127
004 110 622
005 028 043 048 076 096 155 004 051 127 151 153
154 231 236 238 247 252 168 121 514
070
087 590
031 168
007 057
164 197 028 157 149 066 217
028 043 238 052 168
004
043
165 031
070 073 130 144 160 161 004 008 009 034 056 074
091 155 232 233 236 239 245 081 120
031
004 073
239
004 106 112 127 247 250
256
028 043
046
004 116 623
004
099
028
220
164
043
198 021 619 630
004 007 009 011 072 010 012 023 075 127 158 236
238 587 613 614
027 039 098
238 046
122
609
049 067
055 096
164
215 225 046 532 595
129
068 069 078 096 100 164 168 229 026 454 604 617
236
HOMECAST
MINERVA
MOXI
SUDDENLINK
TECHNICOLOR
THOMPSON
Set-Up Code Number
004
178
111
579
002
002 365
TV
Manufacturer/Brand
ADMIRAL
ADVENT
AIWA
AKAI
AKIO
ALARON
ALBATRON
AMARK
AMERICA ACTION
AMERICAN HIGH
AMPRO
ANAM
AOC
APEX
APEX DIGITAL
AQUAVISION
ASTAR
AUDIOVOX
AVION
AXION
BAYSONIC
BELL&HOWELL
BENQ
BRADFORD
BROKSONIC
BYDESIGN
CAIRN
CANDLE
CANON
CAPEHART
CARVER
CELEBRITY
CETRONIC
CINERAL
CITIZEN
CLASSIC
COBY
CONCERTO
CONTEC
CORONADO
CRAIG
CROSLEY
CROWN
CURTIS MATHES
CXC
DAEWOO
DAYTRON
DELL
DENON
Set-Up Code Number
072 081 160 161 096
147 224
238 141 145
031 070 146 004 148 124 226 104 108 615
103
028
253
112 127
043
236
073 167 245
043 054 056 080 112 236
058 070 004 112 616
572
015 150 036 037
164
164
076 103 043 035 224 228 078
223
043
043
072
600
043
231 252 096 170
254
162
070 002 003 004
236
058
164
001
043
103 120
070 002 003 004 101 103 127
043
640 641
004
043 051
127
043 054 028 239
164
043 127
070 004 101 127 236 011 072 081 120 164
043
076 103 112 004 127 016 043 044 125 120 235 249
004 127
004 041 164 618
011
ENVISION
EPSON
ESA
FISHER
FUJITSU
FUNAI
FUSION
FUTURETECH
GATEWAY
GE
GEM
GIBRALTER
GO VIDEO
GOLDSTAR
GPX
GRUNPY
H&B
HAIER
HALL MARK
HANNSPREE
HARLEY DAVIDSON
HARSPER
HARMAN KARDON
HARVARD
HISENSE
HITACHI
HP
HQ
HUMAX
HYPERION
HYUNDAI
ILO
INFINITY
INFOCUS
INKEL
INSIGNIA
INSTANTREPLAY
TV
Manufacturer/Brand
INTEQ
JBL
JCB
JCL
JCPENNEY
JENSEN
JVC
KENWOOD
KLEGG
KLOSS
KONKA
KREISEN
KTV
LG
LLOYD
LODGENET
LOEWE
LOGIK
LUXMAN
LXI
MAGIN
MAGNAVOX
MAJESTIC
MARANTZ
MARTA
MATSUI
MATSUSHITA
MAXENT
MEGAPOWER
MEGATRON
MEI
MEMOREX
METZ
MGA
MIDLAND
MINERVA
MINTEK
MINUTZ
MITSUBISHI
MONIVISION
MOTOROLA
MTC
MULTITECH
NAD
NEC
NEXUS
NIKEI
NIKKO
NIKO
NORCENT
NORWOOD MICRO
NTC
NUVISION
TV
Set-Up Code Number
073
164
001
236
004 008 024 030 065 070 101 127 160 156 234 236
239 247
013
038 001 034 083 195 236 242 159 227 581
070 001 238
220
002 059
026
202
070 043 127 154
004 106 112 127 247 250 569 598 698 648
238
072
196 164
072
004
007 015 052 081 160 164 238
239
070 003 004 022 059 060 061 063 064 127 164 094
160 056 236 238 243 205 028 138 168 035 211 077
050 218
072
164 070 236 243 182 584
247
164
080
165
253
004
236
004 007 072 234 236 238 245 247 028 096
088
024 070 004 042 239
073
088
077
008
109 024 042 004 040 146 028 232 255 081 200 450
550
253
081
070 004 062 101 238 239
238 043
015 025
070 130 134 040 056 007 019 024 004 182 140 575
620 078
043
103
175
211
079
103
084 567 667
Manufacturer/Brand
OLEVIA
ONKING
ONWA
OPTIMUS
OPTOMA
OPTONICA
ORION
PANASONIC
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
POLAROID
PORTLAND
PRISM
PRIMA
PROSCAN
PROTON
PROTRON
PROVIEW
PROX
PYLE
QUASAR
RADIO SHACK
RCA
REALISTIC
REVOLUTION HD
RICO
RUNCO
SABIO
SAMPO
SAMSUNG
SANSEI
SANSUI
SANYO
SCEPTRE
SCOTCH
SCOTT
SEARS
SELECO
SEMIVOX
SEMP
SHARP
SHERWOOD
SIGNATURE
SKYWORTH
SOLE
SONY
TV
Set-Up Code Number
219 004 161 144 160
043
043
080
029 032
019 081
096 201 203 204 205 231 252 028
034 056 080 164 234 236 244 190 230 248 524 624
607
236
070 003 004 024 056 059 060 063 064 127 164 236
238 243
164 005 038 093 127 070 003 004 059 236
238 243 247 199 218 144 161 594
247
023 025 135 176 004 018 070 183 191 208 214 182
660
015 024 031 046 086 092 097 224 228 006 110 026
118 119
004 127 103
034
147 164
144 160 161 167
004 058 127 171 173 193 163
102 213 004 115
110
572
257
034 056 234 236 244 606
004 019 127 043 250
160 161 144 156 065 070 004 023 024 056 074 152
232 233 236 238 239 081 588
007 019 236 238 239 247
220
241
072 073 130 179 180 181 182 216 194
161
070 004 058 165
004 101 127 133 160 089 105 070 237 239 184 185
192 461 578 655
120
238 252 096 615
007 053 057 082 020 239
036
004
004 005 028 043 048 127 113
004 007 015 028 030 057 082 094 127 160 238 247
052 164
189
043
015
081 014 019 028 004 022 127 236 251 496
129 128
072 238
164
177 178
001 085 126 139 236 240 241 602 608 651
Manufacturer/Brand
SOUNDESIGN
SOVA
SOYO
SPECTRICON
SPECTRONIQ
SQUAREVIEW
SSS
STARLITE
SUNBRITE
SUNBRITE TV
SUPERSCAN
SUPRE MACY
SUPREME
SV2000
SVA
SYLVANIA
SYMPHONIC
SYNTAX OLEVIA
TANDY
TATUNG
TEAC
TECHNICS
TECHNOL ACE
TECHVIEW
TECHWOOD
TEKNIKA
TELEFUNKEN
TELERENT
TERA
THOMPSON
TNCI
TMK
TOSHIBA
TOTEVISION
TRUTECH
UNITECH
UNIVERSAL
VENTURER
VIDEO CONCEPTS
VIDEOSONIC
VIDIKRON
VIDTECH
VIEWSONIC
VIORE
VISCO
VITO
VIZIO
WARDS
WESTINGHOUSE
WINBOOK
YAMAHA
YORK
YUPITERU
ZENITH
ZONDA
Set-Up Code Number
003 004 028 043 238
004 169 174
163
112
004
052
004 043
043
608 001 635
605
168
002
001
168
046
070 003 052 059 060 063 064 127 160 164 044 056
236 238 243 168 121 593
052 238 168
219 004 161 144 160
081 238
056 062
238
034 080 236 244
028
246
004
002 003 004 024 028 043 072 101 127 103 236 238
247 164
615
072
172
166
073
004
015 030 007 040 062 101 142 137 045
127 239 247
212
239
008 009
004
146 238
239
188 164 182
004
210
055 592
209 110
004
004 031 603 724 625
004 064 164 008 009 019 028 060 061 063 072 074
127 070 236 238 239
076 036 221 222 001
079
004 070 238 206 207
004
043
011 072 073 095 103 238 241 245 247 096
112
Download PDF

advertising