POWER
COAX
PC USB
1
OPT
2
1
5V 2.1A
RDD-1580
RDD-1580
Digital to Analog Converter
OwnerÊs Manual
2
USB
RDD-1580 Digital to Analog Converter
2
Important Safety Instructions
Notice
The COMPUTER I/O connection should be handled by authorized
persons only.
WARNING: There are no user serviceable parts inside. Refer all
servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose
the unit to moisture or water. Do not expose the unit to dripping or
splashing. Do not place objects filled with liquids, such as vases, on
the unit. Do not allow foreign objects to get into the enclosure. If the
unit is exposed to moisture, or a foreign object gets into the enclosure,
immediately disconnect the power cord from the wall. Take the unit
to a qualified service person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and
on the product itself. Follow all operating instructions.
Clean the enclosure only with a dry cloth or a vacuum cleaner.
Do not use this unit near water.
Do not place the unit on a bed, sofa, rug, or similar surface that could
block the ventilation openings. If the unit is placed in a bookcase or
cabinet, there must be ventilation of the cabinet to allow proper cooling.
Keep the component away from radiators, heat registers, stoves, or
any other appliance that produces heat.
WARNING: The rear panel power cord connector is the mains power
disconnect device. The apparatus must be located in an open area that
allows access to the cord connector.
The unit must be connected to a power supply only of the type
and voltage specified on the rear panel. (USA: 120 V/60Hz,
EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied
power supply cable or an exact equivalent. Do not modify the
supplied cable. A polarized plug has two blades, with one wider than
the other. A grounding plug has two blades plus a third grounding
prong. These are provided for your safety. Do not defeat grounding
and/or polarization safety provisions. If the supplied plug does not
fit your outlet, please consult an electrician for replacement of the
obsolete outlet. Do not use extension cords.
The main plug of the power cordset is a disconnect device of the
apparatus. In order to completely disconnect the apparatus from the
supply mains, the main plug of the power cordset should be unplugged
from the mains (AC) outlet. The stand-by LED indicator will not be lit
up to show the power cord is unplugged. The disconnect device shall
remain readily operable.
Do not route the power cord where it will be crushed, pinched, bent,
exposed to heat, or damaged in any way. Pay particular attention to the
power cord at the plug and where the cord exits the back of the unit.
The power cord should be unplugged from the wall outlet during a
lightning storm or if the unit is to be left unused for a long period of time.
This apparatus shall be connected to a main socket outlet with a
protective earth connection.
Rotel products are designed to comply with
international directives on the Restriction of
Hazardous Substances (RoHS) in electrical and
electronic equipment and the disposal of Waste
Electrical and Electronic Equipment (WEEE). The
crossed wheelie bin symbol indicates compliance and
that the products must be appropriately recycled
or processed in accordance with these directives.
Use only accessories specified by the manufacturer.
Use only with a cart, stand, rack, bracket or shelf
system recommended by Rotel. Use caution when
moving the unit in a stand or rack to avoid injury
from a tip-over.
Immediately stop using the component and have it inspected and/
or serviced by a qualified service agency if:
Ć The power supply cord or plug has been damaged
Ć Objects have fallen or liquid has been spilled into the unit
Ć The unit has been exposed to rain
Ć The unit shows signs of improper operation
Ć The unit has been dropped or damaged in any way
This symbol means that this unit is double insulated.
An earth connection is not required.
Pin Assignments
The batteries in the remote control should not be exposed to excessive
temperature such as sunshine, fire or other heat sources.
2
1
3
Balanced Audio (3 pole XLR):
Pin 1: Ground / Screen
Pin 2: In phase / +ve / Hot
Pin 3: Out of phase / -ve / Cold
3
Figure 1:
Controls and Connections
1
2
3
POWER
COAX
PC USB
1
OPT
2
1
2
USB
5V 2.1A
RDD-1580
4
6
Figure 2:
RR-DD91 Remote Control
7
5
8
A
OFF
9 0
ON
B
C
D
F
E
-
RDD-1580 Digital to Analog Converter
4
Figure 3:
Analog Outputs and Digital Inputs
Computer
CD PLAYER
DIGITAL AUDIO OUTPUT
COAXIAL
OPTICAL
(Supplied)
RDD-1580
RA-1570
5
Figure 4:
Balanced (XLR) Outputs and 12V Triger IN Connections
RDD-1580
RA-1570
Figure 5:
Front USB Input
POWER
COAX
PC USB
1
OPT
2
1
2
5V 2.1A
RDD-1580
USB Memory
or Bluetooth Dongle
USB
6
RDD-1580 Digital to Analog Converter
Important Notes
When making connections be sure to:
 Turn off all the components in the system before hooking up any components, including loudspeakers.
 Turn off all components in the system before changing any of the connections to the system.
Remarques importantes
Pendant les branchements, assurez-vous que :
 Tous les maillons sont éteints avant leur branchement, quels quÊils soient, y compris les enceintes acoustiques.
 Éteignez tous les maillons avant de modifier quoi que ce soit au niveau de leurs branchements, quels quÊils soient.
Wichtige Hinweise
Achten Sie beim Herstellen der Verbindungen auf Folgendes:
 Schalten Sie alle Komponenten im System ab, bevor Sie Geräte (einschließlich Lautsprecher) anschließen.
 Schalten Sie alle Komponenten im System ab, bevor Sie Anschlüsse im System verändern.
Notas Importantes
Cuando realice las conexiones, asegúrese de que:
 Desactiva todos los componentes del equipo, cajas acústicas incluidas, antes de conectar cualquier nuevo componente en el mismo.
 Desactiva todos los componentes del equipo antes de cambiar cualquier conexión del mismo.
Héél belangrijk
Bij het maken van de verbindingen:
 Zorg dat niet alleen de RDD-1580, maar de gehele installatie uitstaat, als nog niet alle verbindingen gemaakt zijn.
 Zorg dat niet alleen de RDD-1580, maar de gehele installatie ook uitstaat, als u verbindingen gaat wijzigen.
Note importanti
Quando effettuate i collegamenti assicuratevi di:
 Spegnere tutti i componenti del sistema prima di collegare qualsiasi componente, inclusi i diffusori.
 Spegnere tutti i componenti del sistema prima di modificare qualsiasi connessione nel sistema.
Viktigt
Tänk på följande när du gör anslutningar:
 Stäng av alla apparater i anläggningen innan du ansluter nya komponenter eller högtalare.
 Stäng av alla apparater i anläggningen innan du ändrar någon anslutning.
LJÊÌ˚ Á‡Ï˜‡ÌËfl
èÂ‰ ÔÓ‰ÒÓ‰ËÌÂÌËÂÏ:
 Ç˚Íβ˜ËÚ ‚Ò ÍÓÏÔÓÌÂÌÚ˚, ‚Íβ˜‡fl ÍÓÎÓÌÍË.
 Ç˚Íβ˜ËÚ ‚Ò ÍÓÏÔÓÌÂÌÚ˚ ‚ ‚‡¯ÂÈ ÒËÒÚÂÏÂ, ÔÂʉ ˜ÂÏ ˜ÚÓ-ÚÓ ‚ ÌÂÈ ÏÂÌflÚ¸.
7
Contents
About Rotel
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 1: Controls and Connections
3
Figure 2: RR-DD91 Remote Control
3
Figure 3: Analog Inputs and Digital Inputs
4
Figure 4: Balanced (XLR) Outputs and 12V Triger IN Connections
5
Figure 5: Front USB Input
5
Important Notes
6
About Rotel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A Few Precautions
7
Placement
8
Cables
8
The RR-DD91 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control Batteries
8
AC Power and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AC Power Input 8
Power Switch and Power Indicator 1
8
Remote Sensor 3
8
Front Input Indicators 4
8
Sampling Frequency Indicators 5
8
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front USB Input 2
9
Bluetooth Connection
9
Analog Outputs 6
9
Digital Inputs 7
9
PC-USB Input 7
9
Computer I/O Connector 8
9
ROTEL LINK 9
9
EXT REM IN Jack 0
9
12 Volt Trigger Input 0
10
Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Source Input 4B
10
Repeat F
10
Random E
10
Factory Default
10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Indicator Is Not Illuminated
10
Fuse Replacement
10
No Sound
10
Can not play 24 bit 192kHz source
10
Playable Audio Format
10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Our story began over 50 years ago. Over the decades, we have received
hundreds of awards for our products and satisfied hundreds of thousands
of people who take their entertainment seriously - like you!
Rotel was founded by a family whose passionate interest in music led them
to manufacture high-fidelity components of uncompromising quality. Through
the years, that passion has remained undiminished and the family goal of
providing exceptional value for audiophiles and music lovers, regardless
of their budget, is shared by all Rotel employees.
RotelÊs engineers work as a close team, listening to, and fine tuning, each
new product until it reaches their exacting musical standards. They are
free to choose components from around the world in order to make that
product the best they can. You are likely to find capacitors from the United
Kingdom and Germany, semiconductors from Japan or the United States,
while toroidal power transformers are manufactured in RotelÊs own factory.
We all have concerns about our environment. And, as more and more
electronics are produced and later discarded, it is especially important for
a manufacturer to do all it can to engineer products that have a minimum
negative impact on landfill sites and water tables.
At Rotel, we are proud to do our part. We have reduced the lead content
in our electronics by using special ROHS solder, while our new Class D
(not digital) amplifiers are up to five times more efficient than our legacy
designs and still deliver power and performance. These products run cool,
give minimum wasted energy, are good for the environment and give better
sound too.
Finally, we have printed this brochure on recycled paper stock.
While we understand that these are small first steps, they are still important
ones. And we continue to pursue new methods and materials for a cleaner
and greener manufacturing process.
All of us at Rotel thank you for buying this product. We are sure it will bring
you many years of enjoyment.
Getting Started
Thank you for purchasing the Rotel RDD-1580 Digital to Analog Converter.
When used in a high-quality music or home theater system, your Rotel
product will provide years of musical enjoyment.
A Few Precautions
Please read this manual carefully. In addition to installation and operating
instructions, it provides valuable information on various RDD-1580 system
configurations as well as general information that will help you get optimum
performance from your system. Please contact your authorized Rotel dealer
for answers to any questions you might have. In addition, all of us at Rotel
welcome your questions and comments.
Save the shipping carton and all enclosed packing material for future use.
Shipping or moving the RDD-1580 in anything other than the original packing
material may result in severe damage that is not covered by the warranty.
RDD-1580 Digital to Analog Converter
8
Fill out and send in the ownerÊs registration card packed with the RDD-1580.
Also be sure to keep the original sales receipt. It is your best record of the date
of purchase, which you will need in the event warranty service is required.
NOTE: Some products are intended for sale in more than one country and
as such are supplied with more than one AC cord. Please use only the cord
appropriate for your country/region.
Placement
The RDD-1580 should be plugged directly into a 2-pin polarized wall outlet
or into the switched outlet on another component in your audio system. Do
not use an extension cord.
Like all audio components that handle low-level signals, the RDD-1580 can
be affected by its environment. Avoid placing the RDD-1580 on top of other
components. Also avoid routing audio signal cables near power cords. This
will minimize the chance it will pick up hum or interference.
We recommend installing the unit in furniture designed to house audio
components. Such furniture is designed to reduce or suppress vibration which
can adversely affect sound quality. Ask your authorized Rotel dealer for advice
about component furniture and proper installation of audio components.
The RDD-1580 is supplied with an RR-DD91 remote control and must be
placed where the infrared signal from the remote can reach the front panel
Remote Sensor.
Cables
Be sure to keep the power cords, digital signal cables and regular audio
signal cables in your installation away from each other. This will minimize
the chance of the regular audio signal cables picking up noise or interference
from the power cords or digital cables. Using only high quality, shielded
cables will also help to prevent noise or interference from degrading the
sound quality of your system. If you have any questions see your authorized
Rotel dealer for advice about the best cable to use with your system.
The RR-DD91 Remote Control
Some functions can be done with either the front panel controls, or the
supplied RR-DD91 remote control. When these operations are described,
the square call out numbers refer to the main unit, while the encircled letters
refer to the remote control.
Remote Control Batteries
Two UM-4/AAA size batteries (supplied) must be installed before the remote
control can be used. To install the batteries, remove the cover on the back of
the RR-DD91. Install the batteries as shown in the illustration in the battery
well. Test the control for proper operation, then replace the cover. When
the batteries become weak the remote control wonÊt operate the RDD-1580
consistently. Installing fresh batteries should eliminate the problem.
Connect the supplied power cord to the Power Connector - on the rear
of the unit and the AC power outlet. The Power indicator light is illuminated
if the unit is plugged in, it is in Standby mode.
If you are going to be away from home for an extended period of time such
as a month-long vacation, it is a sensible precaution to unplug the RDD1580 (as well as other audio and video components) while you are away.
Power Switch and Power Indicator 1
Press the front panel Power Switch button, to turn the unit on. One of the
input selector indicator light is illuminated when the unit is on. Press the
Power Switch button again, the unit is in Standby mode.
When the power indicator is illuminated, the remote control ON and OFF
buttons may be used to activate the RDD-1580.
NOTE: Place the self adhesive ring over the light surrounding the power
switch if the blue light is too bright.
Remote Sensor 3
This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.
Front Input Indicators 4
The front panel has a set of indicators showing which input is currently selected.
PC-USB : This is the rear USB connection
COAX 1 and 2: Set of Coaxial inputs 1 or 2
OPT 1 and 2: Set of Optical inputs 1 or 2
USB : This is the front USB connection.
Sampling Frequency Indicators 5
The Sampling Frequency light will illuminate if the music being played
matches one of the Sampling Frequency indicators.
AC Power and Control
AC Power Input Your RDD-1580 is configured at the factory for the proper AC voltage in
the country where you purchased it, either 120 volts or 230 volts. The AC
line configuration is noted on a decal on the back panel.
NOTE: Should you move your unit to another country, it may be possible to
reconfigure it for use on a different line voltage. Do not attempt to perform
this conversion yourself. Opening the enclosure of the unit exposes you to
dangerous voltages. Consult a qualified service person or the Rotel factory
service department for information.
NOTE: Not all supported Sampling Frequencies have an indicator. Your
music may still play even if it does not have a light associated with the
sample rate of your audio.
9
Connections
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any
signal connections.
Front USB Input 2
See figure 5
The RDD-1580 supports both USB Audio Class1.0 and USB Audio Class 2.0
modes. Windows computers do not require installation of a driver for USB
Audio Class 1.0 and supports playback of audio up to 96KHz sampling
rates. The Factory Default setting is USB Audio Class 1.0.
To take advantage of USB Audio Class 2.0 audio playback supporting
up to 192KHz sampling rates you will need to install the Windows driver
supplied on CD included with the RDD-1580. You will also need to switch
the RDD-1580 to USB Audio Class 2.0 playback mode with the following:
The front USB input can be connected to an iPod, iPhone, USB flash memory
or the Bluetooth dongle (supplied) for wireless streaming. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.
1. Press and Hold the PC-USB source button on the front panel for 5 seconds.
The current USB audio mode is indicated by the blinking Sample Rate LED as:
Bluetooth Connection
2. Press the PC-USB key again to illuminate the 192K sample rate light blinks.
See figure 5
3. Pressing the PC-USB key will toggle between USB Audio Class 1.0 (96KHz
light blinks) and USB Audio Class 2.0 (192KHz light blinks).
Insert the supplied Bluetooth Dongle into the front USB for wireless streaming
via Bluetooth, from your device (i.e. mobile phones) to the RDD-1580. From
your mobile device, look for „Rotel Bluetooth‰ and connect to it. Connection
is normally automatic, but if prompted for a password, please press „0000‰
on your device.
NOTE: Not all Bluetooth dongles will operate with RDD-1580. Please
use the one supplied.
Analog Outputs 6
See figure 3 and figure 4
A pair of standard RCA jacks and XLR balanced connectors supplies an
analog output signal from the RDD-1580 to the source inputs of an audio
preamplifier, integrated amplifier, or receiver.
NOTE: You should choose only one method of analog connection from
the RDD-1580. Do not connect both the RCA and XLR at the same time.
Select high quality audio interconnect cables. Connect the left and right
channel outputs of the RDD-1580 to the corresponding inputs on the
preamplifier or other component.
Digital Inputs 7
USB Audio Class 1.0 ă Sample Rate 96KHz blinking [Factory Default]
USB Audio Class 2.0 ă Sample Rate 192KHz blinking
4. After the desired USB Audio mode is selected wait 3 seconds for the
selection period to end and the RDD-1580 will use the selected audio mode.
5. Power cycle the RDD-1580 and your PC after changing the USB Audio
mode to ensure both units are properly configured.
Many audio playback applications do not support 192KHz sampling rate.
Please confirm your audio player supports 192KHz audio and you have
192KHz audio files to properly playback this sample rate. Also, you may
need to configure the audio driver in your PC to output 192KHz or your
computer may „down sample‰ to a lower audio sample rate. For more
information please refer to your audio player or operating system information.
NOTE: USB Audio Class 2.0 required installation of the Windows PC
driver on the CD ROM included with the RDD-1580. MAC computers do
not require a driver to support PC-USB 1.0 or 2.0 audio.
NOTE: Upon successful installation of the driver, you may need to select
the ROTEL audio driver from the audio/speaker setup of your computer.
Computer I/O Connector 8
The RDD-1580 can be controlled via RS232 for integration with automation
systems. The COMPUTER I/O input accepts a standard straight DB-9 Maleto-Female cable.
See figure 3
There are two sets of digital inputs labeled COAX 1 and 2, OPT 1 and 2.
Connect the COAXIAL or OPTICAL PCM outputs of your source component
into these sockets. The digital signals will be decoded and played by the RDD1580. The unit is capable of decoding PCM signals up to 24 bit, 192kHZ.
PC-USB Input 7
See figure 3
Connect this input using the supplied USB cable to the USB socket of your
computer.
For additional information on the connections, software, and operating codes
for computer control of the RDD-1580, contact your authorized Rotel dealer.
ROTEL LINK 9
This 3.5 mm stereo mini-jack (labeled ROTEL LINK IN) can optionally attach
to Rotel network enabled products with ROTEL LINK OUT connections. This
allows the attached Rotel products to communicate with each other and
be controlled via the Rotel Remote App (available for download on the
iTunes® store).
EXT REM IN Jack 0
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when
the unit is installed in a cabinet and the front-panel sensor is blocked. Consult
RDD-1580 Digital to Analog Converter
10
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to fit the mini-jack receptacle.
12 Volt Trigger Input 0
The RDD-1580 can be activated by a 12 volt trigger signal. The trigger
input accepts any control signal (AC or DC) ranging from 3 volts to 30 volts.
Fuse Replacement
If another electrical device works when plugged into the power outlet, but the
Power Indicator of the unit does not light when plugged into the same outlet
and the Power Switch is pushed in, it indicates that the internal power fuse
may have blown. If you believe this has happened, contact your authorized
Rotel dealer to get the fuse replaced.
When a cable is connected to the 12V input and a trigger signal is present,
the RDD-1580 is activated. When the trigger signal is turned off, the unit
goes into standby mode. The front panel power indicator remains illuminated,
but the unit will not operate.
No Sound
NOTE: When using the 12V Trigger feature, leave the POWER button in
the ON position.
Can not play 24 bit 192kHz source
Audio Controls
Source Input 4B
The Source Input selects the input signal source. From the front panel or
remote press the corresponding input key to select the source to listen to.
Repeat F
Some audio source devices support the use of the repeat function including
Repeat Track, Repeat Album, Repeat Off. Press the Repeat key F on the IR
remote control to toggle these functions. The USB source LED 4 will blink
as follows to indicate the currently activated Repeat function.
Repeat Off: One time blink [Factory Default]
Rpeat Album: Two times blink
Repeat Track: Three times blink
Random E
Some audio source devices support Random playback of music. Press the
Random key E on the IR remote control to toggle the Random function.
The USB audio source LED will blink as follows to indicated the currently
activated function
Random Off: One time blink [Factory Default]
Random On: Two times blink
Factory Default
The RDD-1580 can be reset to restore the factory Default settings. To restore
factory defaults press and hold the front USB source input key 4 for 5
seconds until all Source LEDs are blinking. Release the USB source input
key and the RDD-1580 will restore factory settings and restart.
Troubleshooting
Most difficulties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difficulty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from the
amplifier, refer to the suggestions for the following conditions:
If the unit is getting power, but is producing no sound, check the INPUT
INDICATORS on the front panel. Make sure the selected source is connected.
Also check to make sure the analog outputs of the unit is properly connected.
96kHz and 192kHz playbacks are only available through the rear digital
inputs. Please also note that many media players are not capable of decoding
24bit 192kHz audio files. Please make sure your player can decode 24bit
192kHz files. Also, confirm the RDD-1580 PC-USB input is configured to
USB 2.0 Audio and the Windows audio driver is installed on your computer.
(See PC-USB Input in the manual for more details)
NOTE: MAC computers do not need a driver but require software that
supports 24bit 192kHz playback but still require the RDD-1580 PC-USB
input to be conferred to USB 2.0 Audio.
Playable Audio Format
USB Apple (iPhone, iPod, iPad)
Format
Apple Lossless
MP3
AAC
AIFF
WAV
Notes
Any supported file loaded to Apple device.
Phone may resample depending on stored
format. May exclude Apps designed to play
f
formats
not originally
ll supported
db
by the
h sending
d
device.
USB Bluetooth
Format
Any format supported
by the sending device.
Notes
May exclude Apps designed to play formats not
originally supported by the sending device.
USB Flash Drive
F
Format
t
MP3
WMA
WAV
OGG Vorbis
M4A/AAC
N t
Notes
48K 16 Bit Maximum
PC-USB
Format
Format determined by
the Media Player/
Server software that
you use.
Notes
Any supported format by the PC software
44.1K,
44
1K 48k,
48k 88.2K,
88 2K 96K,
96K 176.4K,
176 4K 192K
16 bit, 24 bit
Coax/Optical
Power Indicator Is Not Illuminated
No main power to the unit. Check the front panel power switch. Make sure
that it is set to the ON position. Check AC power connections at the unit
and the AC outlet.
Format
SPDIF LPCM
Notes
44.1K, 48k, 88.2K, 96K, 176.4K, 192K
16 bit, 24 bit
11
Specifications
RDD-1580
Total Harmonic Distortion
< 0.004%
Intermodulation Distortion (60 Hz : 7 kHz)
< 0.004%
Frequency Response
10Hz - 95kHz+/-3.0dB (MAX)
Signal to Noise Ratio (IHF „A‰ weighted)
128 dB
Input Sensitivity/ Impedance
0 dBfs / 75 Ohms
Output Level / Impedance (RCA)
2.0V / 100 Ohms
Output Level / Impedance (XLR)
4.0V / 200 Ohms
Decodable front USB/iPod Digital Signals
WAV, MP3, WMA
(up to 48kHz 16 bit)
Decodable Coaxial/Optical Digital Signals
SPDIF LPCM
(up to 192kHz 24 bit)
Decodable PC-USB Digital Input Signals
WAV/PCM Depend on the PC
Player used (up to 192kHz 24 bit)
General
Power Requirements (AC)
U.S.A:
Europe:
120 Volts, 60 Hz
230 Volts, 50 Hz
Power Consumption
25 watts
Standby Power Consumption (normal mode)
0.5 watts
Dimensions
Width x Height x Depth
431 x 55 x 316 mm
17 x 21/8 x 121/2 ins.
Front Panel Height
Weight (net)
1U / 43.7mm / 13/4 ins.
5.1kg / 11.24 lbs.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of The Rotel Co, Ltd., Tokyo, Japan.
The Rotel Co. Ltd.
Tachikawa Bldg. 1F.,
2-11-4, Nakane, Meguro-ku,
Tokyo, 152-0031
Japan
Rotel of America
54 Concord Street
North Reading, MA 01864-2699
USA
Phone: +1 978-664-3820
Fax: +1 978-664-4109
„Made for iPod,‰ and „Made for iPhone,‰ means that an electronic accessory
has been designed to connect specifically to iPod or iPhone, respectively, and
has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory
with iPod, or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.
Rotel Europe
Dale Road
Worthing, West Sussex BN11 2BH
England
Phone: + 44 (0)1903 221 761
Fax: +44 (0)1903 221 525
Rotel Deutschland
Vertrieb: B&W Group Germany GmbH
Kleine Heide 12
D-33790 Halle/Westf., Deutschland
Phone: 05201 / 87170
Fax: 05201 / 73370
E-Mail: info@bwgroup.de
www.rotel.com
082 OMRDD1580 052213 English