Chicago Pneumatic | Red Hawk | Operating instructions | Chicago Pneumatic Red Hawk Operating instructions

Safety and operating instructions
Petrol breakers
Valid for United States of America only
CP Red Hawk
www.cp.com
CP Red Hawk
2
9800 0996 93 | Original instructions
CP Red Hawk
Contents
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Safety and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety signal words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Personal precautions and qualifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maintenance, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Storage, precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Design and function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Choosing the correct breaker for a task. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Main parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Insertion tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start and stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
When taking a break. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Every day. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Every year. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Replacing the starter cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Machine data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Noise and vibration declaration statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Noise and vibration data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
EC Declaration of Conformity (EC Directive 2006/42/EC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Emission control system warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chicago Pneumatic Construction Tools warranty statement. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9800 0996 93 | Original instructions
3
Safety and operating instructions
4
CP Red Hawk
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
Introduction
Thank you for choosing Chicago Pneumatic-brand products. For over a century, the
Chicago Pneumatic brand has represented performance and innovation in the
pneumatic tool industry.
Today the brand is found around the world on a range of pneumatic and hydraulic
tools that includes breakers, rock drills, chipping hammers, clay-diggers, picks and
busters, scabblers, pumps and a whole lot more.
The Chicago Pneumatic-brand is associated with powerful and reliable products that
are easy to maintain and that give good value for the money.
For more information please visit www.cp.com
Atlas Copco Construction Tools AB
105 23 Stockholm
Sweden
About the Safety and operating
instructions
The aim of the instructions is to provide you with knowledge of how to use the petrol
breaker in an efficient, safe way. The instructions also give you advice and tell you
how to perform regular maintenance on the petrol breaker.
Before using the petrol breaker for the first time you must read these instructions
carefully and understand all of them.
9800 0996 93 | Original instructions
5
Safety and operating instructions
Safety instructions
To reduce the risk of serious injury or death to
yourself or others, read and understand the Safety
and operating instruction before installing,
operating, repairing, maintaining, or changing
accessories on the machine.
Post this Safety and operating instruction at work
locations, provide copies to employees, and make
sure that everyone reads the Safety and operating
instruction before operating or servicing the
machine.
In addition, the operator or the operator's employer
must assess the specific risks that may be present as
a result of each use of the machine.
CP Red Hawk
> Proper protective boots
> Appropriate work overall or similar clothing (not
loose-fitting) that covers your arms and legs.
Drugs, alcohol or medication
WARNING
Drugs, alcohol or medication
Drugs, alcohol or medication may impair your
judgment and powers of concentration. Poor
reactions and incorrect assessments can lead to
severe accidents or death.
► Never use the machine when you are tired or
under the influence of drugs, alcohol or
medication.
► No person who is under the influence of drugs,
alcohol or medication may operate the machine.
Safety signal words
The safety signal words Danger, Warning and
Caution have the following meanings:
DANGER
Indicates a hazardous situation
which, if not avoided, will result
in death or serious injury.
WARNING
Indicates a hazardous situation
which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation
which, if not avoided, could
result in minor or moderate
injury.
Personal precautions and
qualifications
Only qualified and trained persons may operate or
maintain the machine. They must be physically able
to handle the bulk, weight, and power of the tool.
Always use your common sense and good
judgement.
Personal protective equipment
Always use approved protective equipment.
Operators and all other persons in the working area
must wear protective equipment, including at a
minimum:
> Protective helmet
Installation, precautions
WARNING
Ejected insertion tool
If the tool retainer on the machine is not in a locked
position, the inserted tool can be ejected with force,
which can cause personal injury.
► Always stop the machine before changing the
inserted tool or accessories.
► Never point the inserted tool at yourself or anyone
else.
► Make sure that the insertion tool is fully inserted
and the tool retainer is in a locked position before
the machine is started.
► Check the lock function by pulling the inserted
tool outwards powerfully.
WARNING
Moving or slipping insertion
tool
An incorrect dimension of the inserted tool’s shank
can result in that the inserted tool is lost or is slipping
out during operation. Risk of severe injury or crushed
hands and fingers.
► Check that the insertion tool has the shank length
and dimensions that the machine is intended for.
► Never use an insertion tool without a collar.
> Hearing protection
> Impact resistant eye protection with side
protection
> Respiratory protection when appropriate
> Protective gloves
6
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
Operation, precautions
► Consumed petrol and oil containers must be taken
care of and returned to the retailer.
DANGER
Explosion hazard
If a warm insertion tool or exhaust pipe comes into
contact with explosives, an explosion could occur.
During operating with certain materials, sparks and
ignition can occur. Explosions will lead to severe
injuries or death.
► Never operate the machine in any explosive
environment.
► Never use your fingers to check for fluid leaks.
► Never use the machine near flammable materials,
fumes or dust.
► Make sure that there are no undetected sources
of gas or explosives.
WARNING
Unexpected movements
The inserted tool is exposed to heavy strains when
the machine is used. The inserted tool may break
due to fatigue after a certain amount of use. If the
inserted tool breaks or gets stuck, there may be
sudden and unexpected movement that can cause
injuries. Furthermore, losing your balance or slipping
may cause injury.
► Make sure that you always keep a stable position
with your feet as far apart as your shoulder width,
and keeping a balanced body weight.
► Avoid contact with the warm exhaust pipe or the
bottom of the machine.
► Always inspect the equipment prior to use. Never
use the equipment if you suspect that it is
damaged.
DANGER
Fuel hazard
The fuel (petrol and oil) is extremely flammable and
petrol fumes can explode when ignited, causing
serious injury or death.
► Protect your skin from contact with the fuel. If fuel
has penetrated the skin, consult a qualified health
professional.
► Make sure that the handles are clean and free of
grease and oil.
► Never remove the filler cap, and never fill the fuel
tank when the machine is hot.
► Mix the fuel and fill the fuel tank outdoors or in a
clean and well ventilated place, free from sparks
and open flames. Fill the fuel tank at least ten
meters (30 feet) from the place where the machine
is to be used.
► Release the filler cap slowly to let pressure escape.
► Never overfill the fuel tank.
► Keep your feet away from the inserted tool.
► Stand firmly and always hold on to the machine
with both hands.
► Never start the machine when it is lying on the
ground.
► Never ‘ride’ on the machine with one leg over the
handle.
► Never strike or abuse the equipment.
► Check regularly for wear on the insertion tool,
and check whether there are any signs of damage
or visible cracks.
► Pay attention and look at what you are doing.
► Make sure the filler cap is screwed on when the
machine is used.
► Avoid spilling fuel on the machine, wipe off any
spilled fuel.
► Check regularly for fuel leaks. Never use the
machine if it is leaking fuel.
► Never use the machine in the proximity of material
that can generate sparks. Remove all hot or
spark-generating devices before starting the
machine.
► Never smoke when filling the fuel tank or when
working with the machine or servicing it.
► Only store fuel in a container that is specially
constructed and approved for the purpose.
9800 0996 93 | Original instructions
7
Safety and operating instructions
WARNING
Dust and fume hazard
Dusts and/or fumes generated or dispersed when
using the machine may cause serious and permanent
respiratory disease, illness, or other bodily injury (for
example, silicosis or other irreversible lung disease
that can be fatal, cancer, birth defects, and/or skin
inflammation).
Some dusts and fumes created by drilling, breaking,
hammering, sawing, grinding and other construction
activities contain substances known to the State of
California and other authorities to cause respiratory
disease, cancer, birth defects, or other reproductive
harm. Some examples of such substances are:
> Crystalline silica, cement, and other masonry
products.
> Arsenic and chromium from chemically-treated
rubber.
> Lead from lead-based paints.
Dust and fumes in the air can be invisible to the
naked eye, so do not rely on eye sight to determine
if there is dust or fumes in the air.
To reduce the risk of exposure to dust and fumes,
do all of the following:
► Perform site-specific risk assessment. The risk
assessment should include dust and fumes created
by the use of the machine and the potential for
disturbing existing dust.
► Use proper engineering controls to minimize the
amount of dust and fumes in the air and to
minimize build-up on equipment, surfaces,
clothing, and body parts. Examples of controls
include: exhaust ventilation and dust collection
systems, water sprays, and wet drilling. Control
dusts and fumes at the source where possible.
Make sure that controls are properly installed,
maintained and correctly used.
► Wear, maintain and correctly use respiratory
protection as instructed by your employer and as
required by occupational health and safety
regulations. The respiratory protection must be
effective for the type of substance at issue (and if
applicable, approved by relevant governmental
authority).
► Work in a well ventilated area.
► If the machine has an exhaust, direct the exhaust
so as to reduce disturbance of dust in a dust filled
environment.
► Operate and maintain the machine as
recommended in the operating and safety
instructions
8
CP Red Hawk
► Select, maintain and replace consumables/
inserted tools/ other accessory as recommended
in the operating and safety instructions. Incorrect
selection or lack of maintenance of consumables/
inserted tools/ other accessories may cause an
unnecessary increase in dust or fumes.
► Wear washable or disposable protective clothes
at the worksite, and shower and change into clean
clothes before leaving the worksite to reduce
exposure of dust and fumes to yourself, other
persons, cars, homes, and other areas.
► Avoid eating, drinking, and using tobacco
products in areas where there is dust or fumes.
► Wash your hands and face thoroughly as soon as
possible upon leaving the exposure area, and
always before eating, drinking, using tobacco
products, or making contact with other persons.
► Comply with all applicable laws and regulations,
including occupational health and safety
regulations.
► Participate in air monitoring, medical examination
programs, and health and safety training
programs provided by your employer or trade
organizations and in accordance with
occupational health and safety regulations and
recommendations. Consult with physicians
experienced with relevant occupational medicine.
► Work with your employer and trade organization
to reduce dust and fume exposure at the worksite
and to reduce the risks. Effective health and safety
programs, policies and procedures for protecting
workers and others against harmful exposure to
dust and fumes should be established and
implemented based on advice from health and
safety experts. Consult with experts.
DANGER
Exhaust gas hazard
The exhaust gas from the machine’s combustion
engine contains carbon monoxide which is
poisonous, and chemicals known to the State of
California and other authorities to cause cancer, birth
defects, or other reproductive harm. Inhalation of
exhaust fumes can cause serious injury, illness, or
death.
► Never inhale exhaust fumes.
► Never operate the machine indoors or in a poorly
ventilated area.
► Never stand in a deep hole, ditch, or simular
surrounding during operating.
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
WARNING
Dust hazard
Some dusts, fumes or other airborne material created
during use of the machine may contain chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm. Some
examples of such chemicals are:
> Crystalline silica, cement, and other masonry
products.
WARNING
Motion hazards
When using the machine to perform work-related
activities, you may experience discomfort in the
hands, arms, shoulders, neck, or other parts of the
body.
► Adopt a comfortable posture whilst maintaining
secure footing and avoiding awkward
off-balanced postures.
> Arsenic and chromium from chemically-treated
rubber.
► Changing posture during extended tasks may
help avoid discomfort and fatigue.
> Lead from lead-based paints.
► In case of persistent or recurring symptoms,
consult a qualified health professional.
► To reduce your exposure to these chemicals, work
in a well ventilated area and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
WARNING
Projectiles
Failure of the work piece, of accessories, or even of
the machine itself may generate high velocity
projectiles. During operating, splinters or other
particles from the working material may become
projectiles and cause personal injury by striking the
operator or other persons. To reduce these risk:
► Use approved personal protective equipment and
safety helmet, including impact resistant eye
protection with side protection.
► Make sure that no unauthorised persons trespass
into the working zone.
► Keep the workplace free from foreign objects.
► Ensure that the work piece is securely fixed.
WARNING
Splinters hazard
Using the insertion tool as a hand struck tool can
result in splinters hitting the operator and can cause
personal injury.
► Never use a insertion tool as a hand struck tool.
They are specifically designed and heat-treated to
be used only in a machine.
WARNING
Slipping, tripping and
falling hazards
There is a risk of slipping or tripping or falling, for
example tripping on the hoses or on other objects.
Slipping or tripping or falling can cause injury. To
reduce this risk:
► Always make sure that no hose or other object is
in your way or in any other person's way.
► Always make sure you are in a stable position with
your feet as far apart as your shoulders width and
keeping a balanced body weight.
9800 0996 93 | Original instructions
9
Safety and operating instructions
WARNING
Vibration hazards
Normal and proper use of the machine exposes the
operator to vibration. Regular and frequent exposure
to vibration may cause, contribute to, or aggravate
injury or disorders to the operator’s fingers, hands,
wrists, arms, shoulders and/or nerves and blood
supply or other body parts, including debilitating
and/or permanent injuries or disorders that may
develop gradually over periods of weeks, months,
or years. Such injuries or disorders may include
damage to the blood circulatory system, damage to
the nervous system, damage to joints, and possibly
damage to other body structures.
If numbness, persistent recurring discomfort,
burning sensation, stiffness, throbbing, tingling,
pain, clumsiness, weakened grip, whitening of the
skin, or other symptoms occur at any time, when
operating the machine or when not operating the
machine, stop operating the machine, tell your
employer and seek medical attention. Continued
use of the machine after the occurrence of any such
symptom may increase the risk of symptoms
becoming more severe and/or permanent.
Operate and maintain the machine as recommended
in these instructions, to prevent an unnecessary
increase in vibration.
The following may help to reduce exposure to
vibration for the operator:
► Let the tool do the job. Use a minimum hand grip
consistent with proper control and safe operation.
► If the machine has vibration absorbing handles,
keep them in a central position, avoid pressing
the handles into the end stops.
► When the percussion mechanism is activated, the
only body contact with the machine you should
have are your hands on the handle or handles.
Avoid any other contact, for example supporting
any part of the body against the machine or
leaning onto the machine trying to increase the
feed force. It is also important not to keep the start
and stop device engaged while extracting the tool
from the broken work surface.
► Make sure that the inserted tool is well-maintained
(including sharpness, if a cutting tool), not worn
out, and of the proper size. Insertion tools that
are not well-maintained, or that are worn out, or
that are not of the proper size result in longer time
to complete a task (and a longer period of
exposure to vibration) and may result in or
contribute to higher levels of vibration exposure.
10
CP Red Hawk
► Immediately stop working if the machine
suddenly starts to vibrate strongly. Before
resuming the work, find and remove the cause of
the increased vibrations.
► Never grab, hold or touch the inserted tool when
using the machine.
► Participate in health surveillance or monitoring,
medical exams and training programs offered by
your employer and when required by law.
► When working in cold conditions wear warm
clothing and keep hands warm and dry.
See the ”Noise and vibration declaration statement”
for the machine, including the declared vibration
values. This information can be found at the end of
these Safety and operating instructions.
DANGER
Electrical hazard
The machine is not electrically insulated. If the
machine comes into contact with electricity, serious
injuries or death may result.
► Never operate the machine near any electric wire
or other source of electricity.
► Make sure that there are no concealed wires or
other sources of electricity in the working area.
WARNING
Concealed object hazard
During operating, concealed wires and pipes
constitute a danger that can result in serious injury.
► Check the composition of the material before
operating.
► Watch out for concealed cables and pipes for
example electricity, telephone, water, gas and
sewage lines etc.
► If the inserted tool seems to have hit a concealed
object, switch off the machine immediately.
► Make sure that there is no danger before
continuing.
WARNING
Involuntary start
Involuntary start of the machine may cause injury.
► Keep your hands away from the start and stop
device until you are ready to start the machine.
► Learn how the machine is switched off in the event
of an emergency.
9800 0996 93 | Original instructions
CP Red Hawk
WARNING
Noise hazard
High noise levels can cause permanent and disabling
hearing loss and other problems such as tinnitus
(ringing, buzzing, whistling or humming in the ears).
To reduce risk and prevent an unnecessary increase
in noise levels:
► Risk assessment of these hazards and
implementation of appropriate controls is
essential.
► Operate and maintain the machine as
recommended in these instructions.
Safety and operating instructions
Maintenance, precautions
WARNING
Machine modification
Any machine modification may result in bodily
injuries to yourself or others.
► Never modify the machine. Modified machines
are not covered by warranty or product liability.
► Always use original parts, insertion tools, and
accessories.
► Change damaged parts immediately.
► Select, maintain and replace the insertion tool as
recommended in these instructions.
► Replace worn components in good time.
► If the machine has a muffler, check that it is in
place and in good working condition.
CAUTION
High temperature
The machine's front cover, exhaust pipe, and bottom
become hot during operation. Touching it can lead
to burns.
► Never touch a hot front cover.
► Always use hearing protection.
► Use damping material to prevent work pieces
from "ringing".
WARNING
Unstable position hazard
During operation of the machine, there is a risk for
falling, tripping and/or coming in contact with the
inserted tool, which can cause injury. This risk
increases if you work in an unstable position or on
any unstable ground, object or surface. To reduce
this risk:
► Never work in an unstable position.
► Never touch the hot exhaust pipe.
► Never touch the bottom of the machine when its
hot.
► Wait until the front cover, exhaust pipe, and
bottom of the machine has cooled down before
carrying out maintenance work.
► Always make sure you are in a stable position with
your feet as far apart as your shoulder width and
keeping a balanced body weight.
CAUTION
Hot insertion tool
The tip of the insertion tool can become hot and
sharp when used. Touching it can lead to burns and
cuts.
► Never touch a hot or sharp insertion tool.
► Never stand on any unstable ground, objects or
surfaces.
► Wait until the insertion tool has cooled down
before carrying out maintenance work.
WARNING
Slippery machine surface
hazard
There is a risk that the machine (for example, the
handle and other surfaces) is slippery due to grease,
oil, or other substances. If the machine is slippery,
there is a risk that you might lose your grip, drop
the machine, and/or come in contact with the
inserted tool during operation of the machine. Any
such event can cause injury. To reduce this risk:
► Always make sure that the handles and other
gripping surfaces of the machine are not slippery.
Storage, precautions
♦ Keep the machine and tools in a safe place, out
of the reach of children and locked up.
► Always make sure that the handles and other
gripping surfaces are free from grease and oil.
9800 0996 93 | Original instructions
11
Safety and operating instructions
Overview
CP Red Hawk
Main parts
To reduce the risk of serious injury or death
to yourself or others, read the Safety
instructions section found on the previous
pages of this manual before operating the
machine.
Design and function
CP Red Hawk is a hammering machine. It is equipped
to be used for breaking asphalt and concrete.
Equipped with the right accessories, the machine
can also be used for driving posts, fences, and
ground sampling.
CP Red Hawk is designed for breaking. No other use
is permitted.
To choose the correct insertion tool, check the tool
shank dimension on the machine, and see the spare
parts list.
Choosing the correct
breaker for a task
It is important to choose the correct size of breaker
for the work to be performed.
A breaker that is too small means that the work will
take longer.
A breaker that is too large means that there must be
frequent repositioning, which is unnecessarily tiring
for the operator.
A simple rule for choosing the correct size of breaker
is that a normal sized piece of broken material should
be removed from the workpiece within 10–20
seconds operation.
> If it takes less than 10 seconds a smaller breaker
should be selected.
> If it takes more than 20 seconds a larger breaker
should be selected.
12
A.
Tank cap
B.
Reed valve
C.
Vibration-dampened handle
D.
Power take-off
E.
Fuel filter
F.
Spark plug cover
G.
Percussion piston
H.
Gas duct valve
I.
Tool retainer
J.
Compression chamber for flushing air
K.
Intake valve for flushing air
L.
Muffler
M.
Engine piston
N.
Throttle lever
O.
Stop button
P.
Air filter cover
Q.
Choke
9800 0996 93 | Original instructions
CP Red Hawk
Labels
Safety and operating instructions
Noise level label
The machine is fitted with labels containing
important information about personal safety and
machine maintenance. The labels shall be in such
condition that they are easy to read. New labels can
be ordered from the spare parts list.
The label indicates the guaranteed noise level
corresponding to EC-directive 2000/14/EC. See
"Technical data" for accurate noise level.
Warning label
Data plate
A.
Machine type
B.
Serial number
C.
The warning symbol together with the book
symbol means that the user must read the
Safety and operating instructions before the
machine is used for the first time.
D.
The CE symbol means that the machine is
EC-approved. See the EC Declaration of
Conformity which is delivered with the
machine for more information.
9800 0996 93 | Original instructions
To reduce the risk of injury, everyone using,
installing, repairing, maintaining, changing
accessories on, or working near this tool must read
and understand the safety instructions before
performing any such task.
Operate with chisel retainer in place.
Emission compliance label
13
Safety and operating instructions
Emissions compliance period referred to on the label
indicates the number of operating hours for which
the engine has been shown to meet Federal
emissions requirements.
Category C = 50 hours, B = 125 hours, and A = 300
hours.
Transport
WARNING
Fuel hazard
► Empty the tank before transport.
CP Red Hawk
► Avoid spilling fuel and wipe off any fuel spilled
on the machine.
Filling procedure
1. Stop the engine and let it cool down before
filling the tank.
2. The machine must be in the upright position
when filling with fuel.
3. Never overfill the tank (A).
Installation
Fuel
Two-stroke oil
The fuel is petrol with a 2% oil mixture (1 part oil to
50 parts petrol). Always use high quality lead-free
petrol (non-alcylat).
For the best lubricating results use Chicago
Pneumatic’s environmentally friendly two-stroke oil,
which has been specially developed for the petrol
engined hammering machines.
If Chicago Pneumatic’s two-stroke oil is not available,
use a high quality two-stroke oil for air-cooled
engines (not two-stroke oil for outboard engines).
Contact your local representative for advice on the
correct two-stroke oil.
Mixing the petrol and oil
Always mix the petrol and oil in a clean petrol can.
First add the oil and then the correct amount of
petrol. Then shake the can thoroughly. Shake the
can before every refilling.
NOTICE
During long term storage of two-stroke
mixture, the oil and petrol can separate. Never mix
more fuel than you intend to use within two weeks.
Filling
WARNING
Fuel hazard
The fuel (petrol and oil) is extremely flammable and
petrol fumes can explode when ignited, causing
serious injury or death.
► Protect your skin from contact with the fuel.
4. Release the filler cap slowly to let any pressure
escape.
5. Make sure that the filler cap is screwed on when
the machine is used.
Insertion tool
CAUTION
Hot insertion tool
The tip of the insertion tool can become hot and
sharp when used. Touching it can lead to burns and
cuts.
► Never touch a hot or sharp insertion tool.
► Wait until the insertion tool has cooled down
before carrying out maintenance work.
► Never remove the filler cap and never fill the fuel
tank when the machine is hot.
► Never smoke when filling the fuel tank or when
working with the machine or servicing it.
14
9800 0996 93 | Original instructions
CP Red Hawk
NOTICE
Never cool a hot insertion tool in water,
it can result in brittleness and early failure.
Checking for wear on the tool shank
Safety and operating instructions
WARNING
Vibration hazard
Using inserted tools that do not fulfil the criterias
mentioned below, will result in a longer time to
complete a task, and may result in higher levels of
vibration exposure. A worn tool will also cause
increased working time.
► Make sure that the inserted tool is
well-maintained, not worn out and of the proper
size.
► Always use a sharp tool in order to work
efficiently.
Use the gauge that corresponds to the insertion
tool’s shank dimension. See section "Technical data"
for correct tool shank dimensions.
Fitting and removing the insertion tool
Whenever fitting or removing the insertion tool the
following instructions must be observed:
1. Stop the machine and wait until the inserted tool
has cooled down.
2. Fit or remove the insertion tool.
Operation
WARNING
Involuntary start
Involuntary start of the machine may cause injury.
► Keep your hands away from the start and stop
device until you are ready to start the machine.
► Learn how the machine is switched off in the event
of an emergency.
3. Close the tool retainer by using your foot.
9800 0996 93 | Original instructions
15
Safety and operating instructions
Start and stop
Cold start
CP Red Hawk
Stopping
1. Stop the machine by sliding the stop button on
the left handle forward.
1. Close the choke by turning the choke control
anticlockwise to position (CHOKE).
Operating
2. Push the throttle lever down and pull the starter
handle.
Starting a cut
♦ Stand in a stable position with your feet well away
from the inserted tool.
♦ Press the machine against the working surface
before you start.
♦ The working speed of the machine is controlled
via the throttle lever.
♦ Start collaring at such a distance from the edge
that the machine is capable of breaking the
material without leverage.
♦ Never break off too large pieces. Adjust the
breaking distance (A) so that the inserted tool
does not fasten.
3. When the machine ignites, open the choke one
step clockwise towards position (RUN). Let the
machine run for a 30-60 seconds warm up
period.
Breaking
♦ Never use the machine as a lever, the material
should be broken by impact energy.
♦ Let the machine do the work. Never press too
hard. The vibration absorbing handle should never
be forced all the way to the bottom.
♦ Release the throttle lever when the machine is
lifted.
Restarting a warm machine
If a hot engine stops after a short while or does not
start at all, use the following restart procedure:
1. Check that the choke is open (in position RUN).
When taking a break
2. Pull the starter handle.
♦ During all breaks you must put the machine away
so that there is no risk for unintentional start.
3. If the machine still does not start follow the
procedure for "Cold start" or see the section
"Troubleshooting".
16
♦ Stop the machine during breaks.
9800 0996 93 | Original instructions
CP Red Hawk
Maintenance
Safety and operating instructions
Tool chuck check
Regular maintenance is a basic requirement for the
continued safe and efficient use of the machine.
Follow the maintenance instructions carefully.
♦ Before starting maintenance on the machine,
clean it in order to avoid exposure to hazard
substances. See “Dust and fume hazards”
♦ Use only authorised parts. Any damage or
malfunction caused by the use of unauthorised
parts is not covered by warranty or product
liability.
♦ When cleaning mechanical parts with solvent,
comply with appropriate health and safety
regulations and ensure there is satisfactory
ventilation.
♦ For major service to the machine, contact your
nearest authorised workshop.
♦ After each service, check that the machine's
vibration level is normal. If not, contact your
nearest authorised workshop.
If the chuck gauge provided can be inserted fully
across the flats of the hexagon chuck, this indicates
that the chuck is worn out and must be replaced.
Air filter check
In the event of continuous use, check and change
the air filters at least every shift.
1. Unscrew the air filter cover.
2. Carefully strike the filter against the palm of your
hand. The filter must never be washed. Extremely
dirty filter must be replaced.
Every day
Before undertaking any maintenance or changing
the inserted tool, turn the machine off.
♦ Clean and inspect the machine and its functions
each day before the work commences.
♦ Perform a general inspection and check that there
are no leaks and no damage.
♦ Check the insertion tool, make sure that it is sharp
and not worn out.
♦ Change damaged parts immediately.
♦ Replace worn components in good time.
In order to ensure that the machine remains within
the stated vibration level values, the following checks
must be performed:
9800 0996 93 | Original instructions
Gas duct check
The gas duct must be checked regularly for carbon
deposits, and cleaned if necessary.
17
Safety and operating instructions
1. Pull the starting handle until the arrow in the
centre of the flywheel (which can be seen
through the fan cover) points upwards. This
indicates that the engine piston is in the upper
position.
CP Red Hawk
Spark plug check
1. Lift the spark plug cover by the lower lip, and
turn it up to one side.
2. Unscrew the gas duct valve (A) and take out the
cleaning rod (B).
3. Clean the gas duct valve (A) and cleaning rod
(B) using the cleaning needle (C) provided.
2. Use a plug spanner to remove the spark plug.
3. If the spark plug is dirty or burned, it must be
replaced. Use original Bosch WR7AC spark plugs.
4. If the electrodes are wet from fuel, dry them off,
check the ignition spark, and pull the starter
handle 2–3 times to ventilate off any excess fuel.
4. Clean the thread on the gas duct valve (A).
5. Clean the channel using the cleaning needle (C)
provided.
6. Check that the ball in the gas duct valve (A) is
not stuck.
18
5. Fit the spark plug back into the cylinder and
make sure that the electrode gap is 1.5 mm
(0.060 in.).
Carburettor check
On delivery the carburettor is adjusted and locked
so it meets EPA’s exhaust-gas standard.
Adjustments of the carburettor must be done by an
authorized workshop.
No.
Carburettor
Settings
1
Main nozzle
1,6 turns open
2
Idling nozzle
2,5 turns open
9800 0996 93 | Original instructions
CP Red Hawk
When loaded, the maximum revs should be
2550–2700 rpm. The idling revs should be
1600–1800 rpm.
Safety and operating instructions
Removing the old starter cord
1. Remove the screw-cap of the PTO and the three
bolts from the protective cover of the starting
mechanism.
Every year
Overhauling should be done after 1 year of
continuous operation. Overhauling should for safety
reasons be performed by authorised personnel at
an authorised workshop.
Repair
Replacing the starter cord
WARNING
Spring tension
The starter spring may cause personal injury by
striking the operator or other persons.
► Wear impact resistant eye protection with side
protection and gloves.
2. Lift off the cover, grasping the starter pulley as
well. Let the cover rotate carefully against the
starter pulley, to release the spring tension.
3. Remove the old starter cord.
Fitting a new starter cord
4. Oil the needle bearing in the starter pulley.
5. Fit the starter pulley and protective cover
together, so that the starting spring locates in
the starter pulley.
6. Wind the full length of the cord onto the pulley.
9800 0996 93 | Original instructions
19
Safety and operating instructions
7. Pre-tension the starting spring by one turn
(clockwise) before fitting the assembly into
place.
8. Pull the starting handle carefully, in order to
locate the cover correctly.
CP Red Hawk
Before a petrol driven machine is deposited it must
be emptied and cleaned of all oil and petrol.
Remaining oil and petrol must be dealt with in a way
that does not affect the environment.
9. Fit and tighten the hexagonal bolts and the PTO
screw-cap.
Troubleshooting
If the engine does not start, is difficult to start, runs
unevenly or has poor output, check the points
mentioned below.
♦ Check that the stop button is in the ON position.
♦ Check the fuel level.
♦ Check the spark plug’s electrode distance.
♦ Check that the air filter is not blocked.
♦ Check that the fuel filter is not blocked.
♦ If the machine still does not work satisfactorily
following this procedure, please contact your
nearest authorised workshop.
Storage
♦ Empty the tank before storing the machine.
♦ Check that the machine is properly cleaned before
putting it away for storage.
♦ Store the machine in a dry place.
♦ We recommend to store the machine in a standing
position. If stored in a lying position, the machine
must be placed on the back cover.
♦ Keep the machine and tools in a safe place, out
of the reach of children and locked up.
Disposal
A used machine must be treated and deposed of in
such a way that the greatest possible portion of the
material can be recycled and any negative influence
on the environment is kept as low as possible, and
in respect to local restrictions.
20
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
Technical data
Products
Description
Tool shank size, in. (mm)
Part number
CP Red Hawk
⅞ x 4¼ (22 X 108)
8318 0900 00
Machine data
CP Red Hawk
Type
1 cylinder, two-stroke, air cooled
Cylinder displacement, ci (cc)
11.3 (185)
Power kw (hp)
2.0 (2.7)
Full speed, loaded machine with tamping tool on bed of sand,
crankshaft (strokes/min)
2600–3000
Speed, unloaded machine, idling (strokes/min)
1600–1800
Carburettor
Membran type (Walbro)
Ignition system
Thyristor type, breakerless
Spark plug (recommended)
Bosch WR7AC
Spark plug gap, in. (mm)
0.060 (1.5)
Fuel type
Petrol (gasoline), Unleaded (non-alkylat), 90–100 octane
Starter
Magnapull
Fuel tank capacity, litres (oz)
1.2 (40.6)
Two-stroke oil
Use a high-quality two-stroke oil for air-cooled two-stroke motors,
e.g. Castrol TTS (not two-stroke oil for outboard motors)
Fuel mixture
2% (1:50)
Fuel consumption, gallon/hour (litres/hour)
0.29–0.37 (1.1–1.4)
Length, in. (mm)
27 1⁄3 (694)
Depth, mm (in.)
281 (11)
Width max, in. (mm)
23 (585)
Weight, lb (kg)
49.8 (22.5)
Ambient temperature, C° (F)
-15 to +37 (5 to 98.6)
Noise and vibration declaration statement
Guaranteed sound power level Lw according to ISO 3744 in accordance with directive 2000/14/EC.
Sound pressure level Lp according to ISO 11203.
Vibration value A and uncertainty B determined according to ISO 20643. See table ”Noise and vibration data”
for the values of A, B, etc.
These declared values were obtained by laboratory type testing in accordance with the stated directive or
standards and are suitable for comparison with the declared values of other tools tested in accordance with
the same directive or standards. These declared values are not suitable for use in risk assessments and values
measured in individual work places may be higher. The actual exposure values and risk of harm experienced
by an individual user are unique and depend upon the way the user works, in what material the machine is
used, as well as upon the exposure time and the physical condition of the user, and the condition of the
machine.
9800 0996 93 | Original instructions
21
Safety and operating instructions
CP Red Hawk
We, Atlas Copco Construction Tools AB, cannot be held liable for the consequences of using the declared
values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation
over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to
managing hand-arm vibration can be found at http://www.humanvibration.com/EU/VIBGUIDE.htm
We recommend a programme of health surveillance to detect early symptoms which may relate to vibration
exposure, so that management procedures can be modified to help prevent future impairment.
Noise and vibration data
Type
CP Red Hawk
22
Noise
Vibration
Declared values
Declared values
Sound pressure
Sound power
Three axes values
ISO 11203
2000/14/EC
ISO 20643
Lp
Lw
r=1m dB(A) rel
20µPa
guaranteed dB(A) rel
1pW
A
B
m/s 2 value
m/s 2 spreads
94
107
8.4
2.5
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
EC Declaration of Conformity
EC Declaration of Conformity (EC Directive 2006/42/EC)
We, Atlas Copco Construction Tools AB, hereby declare that the machines listed below conform to the provisions
of EC Directive 2006/42/EC (Machinery Directive) and 2000/14/EC (Noise Directive), and the harmonised
standards mentioned below.
Motor breaker
Guaranteed sound power level
[dB(A)]
Measured sound power level [dB(A)]
107
105
CP Red Hawk
Following harmonised standards were applied:
♦ ISO/FDIS 11148-4
Following other standards were applied:
♦ 2000/14/EC, appendix VIII
♦ 2005/88/EC
♦ Lloyds Register Quality Assurance, NoBo no.0088
Technical Documentation authorised representative:
Erik Sigfridsson
Atlas Copco Constructions Tools AB
Dragonvägen 2
Kalmar
General Manager:
Erik Sigfridsson
Manufacturer:
Atlas Copco Constructions Tools AB
105 23 Stockholm
Sweden
Place and date:
Kalmar, 2010-01-01
9800 0996 93 | Original instructions
23
Safety and operating instructions
CP Red Hawk
Warranty
This warranty only applies in the United States of America.
Emission control system warranty
Atlas Copco Construction Tools AB warrants to the initial purchaser of the machine and each subsequent
owner that the engine in the machine (in Atlas Copco-brand breaker/drill models Cobra Pro, Cobra TT, Cobra
Combi and in Chicago Pneumatic-brand breaker model CP Red Hawk, as applicable) meets the following two
conditions: (1) the engine, including all parts of its emission control system, is designed, built, and equipped
so it conforms at the time of sale to the initial purchaser with the applicable requirements in 40 CFR Part 1054
regulated by the U.S. Environmental Protection Agency; and (2) the engine, including all parts of its emission
control system, is free from defects in materials and workmanship that may keep it from meeting the applicable
requirements in 40 CFR Part 1054 regulated by the U.S. Environmental Protection Agency. (The above-stated
warranty is referred to herein as “this Emission Control System Warranty”.) This Emission Control System
Warranty covers all components whose failure would increase the engine’s emissions of any pollutant regulated
by the United States Environmental Protection Agency under 40 CFR Part 1054.
The warranty period for this Emission Control System Warranty begins on the date of sale of the machine to
the initial purchaser and ends two years thereafter.
Where a warrantable condition exists under this Emission Control System Warranty, warranty repairs will be
made by an Atlas Copco Representative (as defined below) or by a service facility designated by the Atlas
Copco Representative, without charge for diagnosis, parts, or labor, subject to all other provisions stated
herein. All defective parts replaced under this Emission Control System Warranty become the property of the
Atlas Copco Representative. Normal maintenance items are warranted up to their first required replacement
interval only. Only Atlas Copco Construction Tools AB approved replacement parts may be used in the
performance of any warranty repairs under this Emission Control System Warranty and will be provided without
charge.
This Emission Control System Warranty does not extend to components or parts which are affected or damaged
by the machine owner’s or any other person’s (other than Atlas Copco Construction Tools AB’s or the Atlas
Copco Representative’s) improper use or improper maintenance (including, but not limited to, improper
replacement of filters, sparkplugs or other maintenance items or wear parts; incorrect oil or fuel; stale or
improper fuel mix; dirt or other contaminants in the fuel or oil; excessive dirt, dust, rust, or corrosion in the
engine; improper storage; use of replacement parts or accessories not conforming to the original specifications
which impair the effectiveness of the emission control system; incorporation of or use of unsuitable attachments
or unauthorized alteration of any part; or improper repair), abuse, accident, or acts of God.
This Emission Control System Warranty does not cover replacement of expendable maintenance items (for
example spark plugs and filters) unless they are original items defective in material or workmanship and the
first required replacement interval (in accordance with applicable instructions published by the machine
manufacturer) for the item has not been reached.
Responsibility for Maintenance:
As the machine engine owner, you are responsible for the performance, at your expense, of the proper
maintenance of the engine (in addition to all other parts of the machine and accessories) in accordance with
applicable instructions published by the machine manufacturer, including in the Safety and Operating
Instructions manual for the machine. Atlas Copco Construction Tools AB recommends that you retain all
receipts and maintenance records covering performance of maintenance. Proper maintenance includes, but
is not limited to, routine replacement and servicing of spark plugs, filters, other expendable wear parts, and
any other part or item related to emission control or that may affect emissions.
Requirements related to warranty claims:
Warranty repairs may only be performed by an Atlas Copco Representative or by a service facility designated
by the Atlas Copco Representative to perform the warranty repair. “Atlas Copco Representative” means the
dealer in the United States from whom your machine was initially purchased as a new machine or a service
facility in the United States that is owned or operated by Atlas Copco Construction Equipment LLC and which
performs warranty repair of such machine engines. You are responsible for promptly presenting the machine
24
9800 0996 93 | Original instructions
CP Red Hawk
Safety and operating instructions
(into which the engine is incorporated) to the nearest Atlas Copco Representative as soon as a warrantable
condition exists under this Emission Control System Warranty. At the time of requesting warranty repair, you
must provide proof of the initial purchase of the machine, including the initial purchase date.
If you are located more than 100 miles from the nearest Atlas Copco Representative, the Atlas Copco
Representative will (at its choice) (i) pay for shipping costs of the machine to and from the nearest Atlas Copco
Representative; (ii) provide for a technician to come to you to make the warranty repair under this Emission
Control System Warranty; or (iii) pay for the warranty repair to be made at a local service facility designated
by the Atlas Copco Representative to perform the warranty repair on your machine engine under this Emission
Control System Warranty. (The provisions in the preceding sentence apply only for the contiguous states,
excluding the states with high-altitude areas identified in 40 CFR 1068, Appendix III.) If you are located within
100 miles of an Atlas Copco Representative, you will be responsible for paying all shipping/ transportation
costs, technician travel costs if the technician comes to you, and other similar costs, unless the Atlas Copco
Representative in its discretion elects to pay for such costs or any portion thereof.
If the Atlas Copco Representative determines that there is no warrantable condition under this Emission Control
System Warranty, you will be responsible for the cost of the diagnosis, labor and parts in accordance with the
Atlas Copco Representative’s normal rates, costs of shipping/ transporting (regardless of your distance to an
Atlas Copco Representative), technician travel costs if the technician comes to you, and other similar costs,
unless the Atlas Copco Representative in its discretion elects to pay for such costs or any portion thereof.
For information about how to make a warranty claim and how to make arrangements for authorized warranty
repair, please contact the dealer in the United States from whom your machine was initially purchased as a
new machine. You may also contact Atlas Copco Construction Equipment LLC via telephone at 1-800-760-4049
or via email to acceservice@us.atlascopco.com.
Chicago Pneumatic Construction Tools warranty statement
Chicago Pneumatic Construction Tools products are warranted to be free from defects in material and
workmanship for 12 months* from the date of purchase, provided that usage is limited to single shift operation
throughout that period. If the usage rate exceeds that of single shift operation, the warranty period shall be
reduced as per a pro-rata basis.
This warranty applies only to products purchased new** from Chicago Pneumatic Construction Tools or an
Authorized Service Center. This warranty does not apply to products which have been misused, modified,
and/or repaired by someone other than Chicago Pneumatic Construction Tools or an Authorized Service
Center.
If a Chicago Pneumatic Construction Tools product appears defective in material or workmanship within the
warranty period, return it or ship postage paid to any Authorized Service Center for Chicago Pneumatic
Construction Tools. Please enclose your name, address, dated proof of purchase and a short description of
the defect. Failure to do so could result in delay of product repair or replacement. Chicago Pneumatic
Construction Tools will, at its sole discretion, repair or replace defective products free of charge. Repairs or
replacements are warrantied as described above for the remainder of the original warranty period. Chicago
Pneumatic Construction Tools sole liability and your exclusive remedy under this warranty is limited to repair
or replacement of the defective Product.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, OR CONDITIONS,
WRITTEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ALL WARRANTIES, OR
CONDITIONS, OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH ARE HEREBY
DISCLAIMED, THERE SHALL BE NO LIABILITY FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, OR
ANY OTHER DAMAGES, COSTS OR EXPENSES, EXCEPTING ONLY THE COST OR EXPENSE OF REPLEMENT OR
REPAIR.
* Unless otherwise stated in the warranty supplied with the product.
** Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not
covered by warranty.
9800 0996 93 | Original instructions
25
CP Red Hawk
26
9800 0996 93 | Original instructions
CP Red Hawk
9800 0996 93 | Original instructions
27
2010-01 | No. 9800 0996 93
© Copyright Atlas Copco Construction Tools AB | STOCKHOLM • SWEDEN
Download PDF

advertising