Ryobi CJS-180L User`s manual

CJS-180L
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
CORDLESS JIGSAW WITH LASER
SCIE SAUTEUSE SANS FIL AVEC GUIDE LASER
AKKU-STICHSÄGE MIT LASER
SIERRA DE CALAR INALÁMBRICA CON GUÍA LÁSER
SEGHETTO ALTERNATIVO A BATTERIA CON GUIDA LASER
ACCU-DECOUPEERZAAG MET LASERGELEIDER
SERRA DE RECORTE SEM FIO COM GUIA LASER
BATTERIDREVEN STIKSAV MED LASERSTYR
SLADDLÖS STICKSÅG MED LASER
JOHDOTON KUVIOSAHA JA LASEROHJAIN
OPPLADBAR STIKKSAG MED LASERMARKØR
ãéÅáàäéÇÄü ÄääìåìãüíéêçÄü èàãÄ
ë ãÄáÖêçõå åÖíóàäéå
AKUMULATOROWA WYRZYNARKA Z
LASEROWYM PROWADNIKIEM
AKUMULÁTOROVÁ LISTOVÁ PILA S LASEROVÝM ZAMOVAEM
SZÚRÓFRÉSZ, VEZETÉK NÉLKÜLI, LÉZERES VÁGÁSVEZETVEL
FERSTRU DE CONTUR FR FIR CU GHID LASER
BEZVADU FINIERZ
IS AR LZERU
BEVIELIS SIAURAPJKLIS SU LAZERIU
LASERIGA AKU-TIKKSAAG
BEÆI»NA UBODNA PILA S LASERSKOM VODILICOM
BREZŽINA VBODNA ŽAGA Z LASERSKIM VODILOM
BEZDRÔTOVÁ LISTOVÁ PÍLA S LASEROM
OO Z
LAZER REHBERL KABLOSUZ DARBEL TESTERE
USER’S MANUAL
MANUEL D’UTILISATION
BEDIENUNGSANLEITUNG
MANUAL DE UTILIZACIÓN
MANUALE D’USO
GEBRUIKERSHANDLEIDING
MANUAL DE UTILIZAÇÃO
BRUGERVEJLEDNING
INSTRUKTIONSBOK
KÄYTTÄJÄN KÄSIKIRJA
BRUKSANVISNING
1
6
11
17
22
27
32
37
42
47
52
êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà
57
INSTRUKCJA OBSUGI
NÁVOD K OBSLUZE
HASZNÁLATI ÚTMUTATÓ
MANUAL DE UTILIZARE
LIETOTJA ROKASGRMATA
NAUDOJIMO VADOVAS
KASUTAJAJUHEND
KORISNI»KI PRIRU»NIK
UPORABNIŠKI PRIRONIK
NÁVOD NA POUŽITIE
KULLANiM KILAVUZU
62
67
72
77
82
87
92
97
102
107
112
118
DE ÜBERSETZUNG DER ORIGINALANLEITUNG ES TRADUCCIÓN DE
NL VERTALING VAN DE ORIGINELE INSTRUCTIES PT TRADUÇÃO DAS
INSTRUÇÕES ORIGINAIS DK OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER SE ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA FI
ALKUPERÄISTEN OHJEIDEN SUOMENNOS NO OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE RU PL TUMACZENIE INSTRUKCJI ORYGINALNEJ CZ PEKLAD ORIGINÁLNÍCH POKYN HU AZ EREDETI ÚTMUTATÓ FORDÍTÁSA RO TRADUCEREA
INSTRUCIUNILOR ORIGINALE LV TULKOTS NO ORI
INLS INSTRUKCIJAS LT ORIGINALI INSTRUKCIJ VERTIMAS EE ORIGINAALJUHENDI TÕLGE
HR PRIJEVOD ORIGINALNIH UPUTA SI PREVOD ORIGINALNIH NAVODIL SK PREKLAD POKYNOV V ORIGINÁLI GR !" !#$!"
%" TR ORIJINAL TALIMATLARIN TERCÜMESI
GB
ORIGINAL INSTRUCTIONS
FR
LAS INSTRUCCIONES ORIGINALES
TRADUCTION DES INSTRUCTIONS ORIGINALES
IT
TRADUZIONE DELLE ISTRUZIONI ORIGINALI
961075062-03(CJS-180L)_EU.indd A1
1/5/10 1:37:36 PM
1
7
9
8
2
3
10
4
6
5
Fig. 1
13
12
5
11
3
Fig. 2
Fig. 3
1
9
10
14
2
6
5
Fig. 4
961075062-03(CJS-180L)_EU.indd A2
Fig. 5
1/5/10 1:37:41 PM
1
7
8
17
15
2
4
Fig. 7
Fig. 6
16
17
Fig. 9
Fig. 8
7
4
35
0
17
15
Fig. 10
18
17
Fig. 11
19
20
Fig. 12
961075062-03(CJS-180L)_EU.indd A3
10
Fig. 13
1/5/10 1:37:41 PM
Important!
It is essential that you read the instructions in this manual before operating this machine.
Attention !
Il est indispensable que vous lisiez les instructions contenues dans ce manuel avant la mise en service
de l’appareil.
Achtung!
Bitte lesen Sie unbedingt vor Inbetriebnahme die Hinweise dieser Bedienungsanleitung.
¡Atención!
Es imprescindible que lea las instrucciones de este manual antes de la puesta en servicio.
Attenzione!
Prima di procedere alla messa in funzione, è indispensabile leggere attentamente le istruzioni contenute
nel manuale.
Let op !
Het is van essentieel belang dat u de instructies in deze gebruiksaanwijzing leest vooraleer u dit toestel
in gebruik neemt.
Atenção!
É indispensável que leia as instruções deste manual antes de utilizar a máquina.
OBS!
Denne brugsanvisning skal læses igennem inden ibrugtagning.
Observera!
Det är nödvändigt att läsa instruktionerna i denna bruksanvisning innan användning.
Huomio!
On ehdottoman välttämätöntä lukea tässä käyttöohjeessa annetut ohjeet ennen käyttöönottoa.
Advarsel!
Det er meget viktig at du leser denne brukerveiledningen før du tar maskinen i bruk.
ÇÌËχÌËe!
èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛ͈ËË ËÁ ̇ÒÚÓfl˘e„Ó
ÛÍÓ‚Ó‰ÒÚ‚‡.
Uwaga!
Przed przystpieniem do uytkowania tego urzdzenia, naley koniecznie zapozna si z zaleceniami
zawartymi w niniejszym podrczniku.
D'ležité upozorn(ní!
Nepoužívejte tento pístroj díve, než si petete pokyny uvedené v tomto návodu.
Figyelem!
Feltétlenül fontos, hogy a jelen használati útmutatóban foglalt elírásokat az üzembe helyezés eltt
elolvassa!
Aten)ie!
Este esenial s
citii instruciunile din acest manual înainte de operarea acestui aparat.
Uzmanību!
Svargi, lai js pirms mašnas darbinšanas izlastu instrukcijas šaj rokasgrmat.
Dėmesio!
Prieš praddami eksploatuoti š prietais, svarbu, kad perskaitytumte šiose instrukcijose pateiktus
nurodymus.
Tähtis!
Enne trelli kasutama hakkamist tuleb käesolevas juhendis esitatud juhised kindlasti läbi lugeda.
Upozorenje!
Neophodno je da proitate ove upute prije uporabe ovog ureaja.
Pomembno!
Pred uporabo tega stroja, obvezno preberite navodila iz tega prironika.
Dôležité!
Pre prácou s týmto zariadením je dôležité, by ste si preítali pokyny v tomto návode.
*+.+/:!
" #" $ %& #& ' *+ ;#%.
Dikkat!
Cihaz<n çal<=t<r<lmas<ndan önce bu k<lavuzda bulunan talimatlar< okuman<z zorunludur.
Subject to technical modifications / Sous réserve de modifications techniques /Technische Änderungen vorbehalten /
Bajo reserva de modificaciones técnicas / Con riserva di eventuali modifiche tecniche /Technische wijzigingen voorbehouden /
Com reserva de modificações técnicas / Med forbehold for tekniske ændringer / Med förbehåll för tekniska ändringar /
Tekniset muutokset varataan / Med forbehold om tekniske endringer / åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌ˘eÒÍËe ËÁÏeÌeÌËfl /
Z zastrzeeniem modyfikacji technicznych / Zm>ny technických údaj? vyhrazeny / A m@szaki módosítás jogát fenntartjuk /
Sub rezerva modificaiilor tehnice / Paturam tiesbas maint tehniskos raksturlielumus / Pasiliekant teis daryti techninius pakeitimus /
Tehnilised muudatused võimalikud /Podloæno tehniËkim promjenama /Tehnine spremembe dopušene/
Technické zmeny vyhradené / GK QR;V W'& X$ / Teknik deYi=iklik hakk< sakl<d<r
961075062-03(CJS-180L)_EU.indd A4
1/5/10 1:37:41 PM
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
English
SPECIFIC SAFETY RULES
Q
SPECIFICATIONS
Motor
Switch
No Load Speed
Cutting Angle
Maximum Cutting
Thickness(Wood )
Blade Stroke
Shank capacity
Orbital Motion
Laser Guide
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
SAFETY RULES FOR LASER GUIDE
The laser guide radiation used in saw is Class 2M with
maximum <5mW and 650nm wavelengths. These lasers
do not normally present an optical hazard, although
staring at the beam may cause flash blindness.
MODEL
WARNING:
DO NOT stare directly at the laser beam. A
hazard may exist if you deliberately stare into the
beam, please observe all safety rules as follows;
Q
Q
Q
Q
Q
Q
The laser shall be used and maintained in accordance
with the manufacturer’s instructions.
Never aim the beam at any person or an object other
than the work piece.
The laser beam shall not be deliberately aimed at
personnel and shall be prevented from being directed
towards the eye of a person for longer than 0.25s.
Always ensure the laser beam is aimed at a sturdy
work piece without reflective surfaces. i.e. wood or
rough coated surfaces are acceptable. Bright shiny
reflective sheet steel or the like is not suitable for
laser use as the reflective surface could direct the
beam back at the operator.
Do not change the laser guide assembly with a
different type. Repair must only be carried out by the
laser manufacturer or an authorised agent.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also.
CJS-180L
18V
Variable Speed
0-2,100 min-1
0º to 45º(Right)
40 mm
19 mm
6.35 mm
4 Settings
Class 2M,5mW max, 650nm
BATTERY PACK
(not included)
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
BPL-1820
BPL-1815
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
CHARGER
(not included)
BCL-1800
BCS618
BCL1418
BC-1815S
BC-1800
DESCRIPTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
LASER RADIATION
DO NOT STARE INTO THE BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
CLASS 2M LASER PRODUCT
CAUTION:
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
Lock-off button
Switch trigger
Blade storage
Orbital adjustment knob
T-shank saw blade
Toolless blade clamp
Hex key
Hex key storage area
Laser guide switch
Laser guide
Battery pack( not included)
Latches
Depress latches torelease Battery pack
Blade clamp lock
Base pivot screw
Edge guide screw
Base
Scale
Moves the laser beam in a rotational direction
Moves the laser beam laterally left to right
1
961075062-03(CJS-180L)_EU.indd Sec1:1
1/5/10 1:37:41 PM
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
English
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
OPERATION
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second issufficient to inflict serious injury.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
WARNING:
Always wear safety goggles or safety glasses
with side shields when operating tools. Failure
to do so could result in objects being thrown into
your eyes, resulting inpossible serious injury.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
BLADE STORAGE(Fig.3)
The blade storage compartment is located on the back
of the saw. It is convenient for storing extra blades and
storing blades when not in use.
APPLICATIONS
Q
You may use this tool for the purposes listed below:
Q
Cutting wood surfaces
Q
Cutting thin sheet metal
Q
Cutting plastics and laminates
Q
WARNING:
Battery tools are always in operating condition.
Therefore, switch should always be locked when
not in use or carrying at your side.
TO INSERT BATTERY PACK(NOT INCLUDED)
Fig.2
Q
Q
Q
Lock the switch trigger by releasing it all the way.
Place the battery pack on the tool.
Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
LASER GUIDE(Fig.4)
Depress the laser guide switch to generate a red laser
beam on the work surface in front of the saw. Use the
laser to guide the saw along the line of cut.
LOCK-OFF BUTTON(Fig.4)
CAUTION:
When placing battery pack in the tool, be sure
raised rib on battery pack aligns with the grooves
in the saw and latches into place properly.
Improper installation of the battery pack can
cause damage to internal -components.
The lock-off button is located on the handle above the
switch trigger. You must depress the lock-off button in
order to pull the switch trigger. The lock resets each time
the trigger is released.
NOTE: You can depress the lock-off button from either
the left or right side.
TO REMOVE BATTERY PACK(NOT INCLUDED)
Fig.2
Q
Q
Q
To open: Push the door down with your thumb or
finger. Place blades in blade storage compartment.
To close: Push the door up with your thumb or finger.
Lock the switch trigger by releasing it all the way.
Depress the latches on the side of battery pack.
Remove the battery pack from the tool.
SWITCH TRIGGER(Fig.4)
To turn the saw ON, depress and hold lock-off button,
then depress the switch trigger. To turn it OFF, release
the switch trigger.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
2
961075062-03(CJS-180L)_EU.indd Sec1:2
1/5/10 1:37:42 PM
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
English
don’t cut halfway and complete the cut from the opposite
end.
OPERATION
WARNING:
This tool is designed to work with T-shank
blades. Use with non-T-shank blades may result
in blades coming loose from tool, resulting in
personal injury or property damage.
SPLINTER-FREE CUTTING(Fig.7)
The base of the jig saw has a narrow slot to permit
splinter-free cutting. It is especially useful when cutting
plywood. This feature should only be used when making
straight cuts or circle cuts. It is not for bevel cutting or
plunge cutting.
BLADE SELECTION
To obtain the best performance from the saw, it is
important to select a specific blade for the particular
application and type of material you wish to cut. By doing
this you will get a smoother, faster cut and prolong blade
life.
NOTE: This tool is designed to work with T-shank blades.
Other types of saw blades are not guaranteed to work
properly and may come loose from the tool.
NOTE: The non-orbital setting also helps reduce
splintering when cutting plywood.
positioning the base in the splinter-free cutting position
Q
Remove battery pack
Q
Using the 3 mm. hex key provided, loosen base pivot
screws and slide base forward.
Q
Always set the cutting angle at 0° for splinter-free
cutting. To set cutting angle at 0°, align the 0° mark
on the scale with the edge of the motor housing.
NOTE: When setting angle at 0° for splinter-free cutting,
the positive stop notches on the rear of the base are not
used.
Q
Tighten base pivot screws securely.
Q
Remove hex key and return it to the storage area.
Q
Replace battery pack.
INSTALLING BLADES(Fig.5)
Q
Q
Q
Q
Q
Remove battery pack.
Lift blade clamp lock located on front of saw.
Insert saw blade between blade clamp and saw bar.
Close blade clamp lock.
Replace battery pack.
GENERAL CUTTING(Fig.6)
OPTIONAL EDGE GUIDE(Fig.8)
Rest the front of the saw base on the workpiece and align
cutting edge of the blade with the line on your workpiece.
Start the saw and move it forward on the work surface.
Apply downward pressure to keep the saw steady and
only enough forward pressure to keep the blade cutting.
Do not force the saw. Forcing the saw may overheat the
motor and break saw blades. Broken saw blades must
be replaced with new saw blades.
An optional edge guide is available for use with the saw.
It can be used for making crosscuts and rip cuts.
Q
Remove battery pack.
Q
Insert the arm through the two slots in the base of the
saw as shown.
Q
Adjust edge guide to the desired width and lock in
place with the edge guide screw.
Q
Replace battery pack.
ORBITAL MOTION(Fig.6)
The blade of the saw cuts in orbital motion. This feature
is adjustable and provides faster, more efficient cutting.
With orbital motion, the blade cuts through your work
in the upstroke but does not drag across your work in
the downstroke. The higher settings should be used
when fast cutting in soft material is desired. The lower
settings should be used when cutting materials with
more resistance.
SCROLL CUTTING(Fig.9)
Scroll cuts can be made with the jig saw by guiding the
direction of the cut with applied pressure on the handle
as shown.
WARNING:
Excessive side pressure to the blade could result
in broken blades or damage to the material being
cut.
STRAIGHT CUTTING(Fig.6)
A straight cut can be made by clamping a piece of wood
or straightedge to the workpiece and guiding the edge of
the saw against it. Make the cut from one direction only;
3
961075062-03(CJS-180L)_EU.indd Sec1:3
1/5/10 1:37:42 PM
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
English
OPERATION
Q
ANGLE CUTTING (Bevel Cutting) (Fig.10Fig.11)
WARNING:
Use of controls or adjustments or performance
of procedures other than those specified herein
could result in hazardous radiation exposure.
Bevel cutting angles may be adjusted from 0° to 45° right
or left. Angles for cuts from 0° to 45° in 15° increments
are marked on a scale on both the left and right side
of the base. Notches on the rear of the base provide
positive stops at each of the above mentioned 15°
increments. A protractor is recommended when accurate
cuts are required.
Q
Q
Q
Q
Q
ADJUSTING THE LASER(Fig.13)
The laser can be realigned by adjusting the two screws
located in the front of the saw. The top screw moves the
laser beam laterally from left to right. The bottom screw
moves the laser beam in a rotational direction.
Remove battery pack.
Using the 3 mm. hex key provided, loosen the base
pivot screws until the base can be moved.
Slide base backward until base pivot screws can
move freely in slots in base.
Align the mark, on the base, of the desired angle with
the edge of the motor housing.
Once the desired angle is reached, slide base forward
until tab on motor housing aligns with the appropriate
notch on rear of base.
NOTE: Draw a pencil line on scrap workpiece parallel to
the long edge of the base as a straight line guide to aid in
the adjusting process.
Q
Remove the blade from the saw.
Q
Turn laser on.
Q
Rest base of saw on scrap workpiece.
Q
Adjust screws as necessary.
Q
Since blade thicknesses vary, always make a trial cut
in scrap workpiece to ensure an accurate cut.
Q
Check for proper alignment.
Q
Repeat as necessary until laser is aligned.
NOTE: When making a set-up for accurate cuts with
a protractor, or for angles other than the preset 15°
increments, the positive stop notches on the rear of the
base are not used.
Q
Tighten the base pivot screws securely.
Q
Return hex key to storage compartment.
Q
Replace battery pack.
NOTE: The wide slot in the base must be used when
making bevel cuts, scroll cuts, plunge cuts, and when
cutting metal.
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses
with side shields during power tool operation or
when blowing dust. If operation is dusty, also
wear a dust mask.
PLUNGE CUTTING(Fig.12)
Q
Q
Q
Q
Q
Continue lowering the blade into the workpiece until
the base rests flat on the work surface, then move the
saw forward to complete the opening.
WARNING:
To avoid loss of control, broken blades, or
damage to the material being cut, always use
extreme caution when making plunge cuts. We
do not recommend plunge cutting on materials
other than wood.
Mark the line of cut clearly on the workpiece.
Set the cutting angle at 0°.
Tilt the saw forward so that it rests on the front edge
of the base and blade will not come in contact with
the workpiece when the saw is turned on.
Make sure the blade is inside the area to be cut.
Using high speed, start the saw and slowly lower the
blade into the workpiece until the blade cuts through
the wood.
WARNING:
To avoid serious personal injury, always remove
thebattery pack from the tool when cleaning or
performing any maintenance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
4
961075062-03(CJS-180L)_EU.indd Sec1:4
1/5/10 1:37:43 PM
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
English
MAINTENANCE
SYMBOL
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken ordestroy plastic which may
result in serious personal injury.
Safety Alert
V
Volts
min-1
Revolutions or reciprocations per minute
Direct current
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorized Service Center.
CE Conformity
ENVIRONMENTAL PROTECTION
Please read the instructions carefully before
starting the machine.
Recycle raw materials instead of disposing as
waste.The machine, accessories and
packaging should be sorted for environmentalfriendly recycling.
Recycle unwanted
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
5
961075062-03(CJS-180L)_EU.indd Sec1:5
1/5/10 1:37:43 PM