Alphatech Fermax IP DP Installation guide

ALPHATECH TECHNOLOGIES s.r.o.
Jeremenkova 88, Praha 4, Czech Republic
www.alphatechtechnologies.cz
Fermax IP DP
SIP based VoIP video door phone panel
Fermax PBX EXP
Fermax PBX KEY
Fermax PBX EA
User and installation guide
Welcome
Congratulations on purchasing the door phone panel Fermax IP DP “VoIP
Door Phone”, which is a SIP based VoIP version of "Fermax PBX DP" analog
door phone panel. This door phone can satisfy your need of communication
with visitors at the entrance to the building, to your company or at the entrance
of your house. VoIP means “Voice over Internet Protocol” – the door phone
is connected to the computer network and enables both P2P (peer to peer)
connection – i.e. it calls to an IP address of other VoIP device directly or it is
registered to a SIP server, then it calls a phone number. There can be
assigned up to two 25 digit numbers including characters “* ”, “ # ” .
The basic module of the door phone always contains 2 pushbuttons and
optionally the first expansion, 8 pushbutton C module. The combination of
Fermax New Cityline panels enable the sets of door phone with 1 to 10
pushbuttons just by using the basic electronics module of Fermax IP DP. You
can also expand the whole system by the 8 pushbutton expansion module
Fermax PBX EXP up to the limit of 64 pushbuttons. The basic module can
contain a colour camera, optionally there can be an add-on speaker module
with an amplifier Fermax PBX EA, which is used for very noisy areas. The
Fermax New Cityline panels are rich with an add ons. For example the panels
offer installations on the surface or flush mounted, they can be used both
indoors and outdoors, there can be add-on roofing used, etc.
The Fermax IP DP door phone panel is powered by 12V of the power
supply, which can also be used for powering the electrical lock of the door. The
Fermax IP DP is also PoE powered (Power over Ethernet). The features of the
door phone are similar to a hands-free telephone. Among basic features you
can find the possibility of opening up to two doors via connected electrical locks
and also an easy WEB based programming.
The producer improves the SW (firmware) of the door phone panel
continuously. Fermax IP DP panel enables uploading the latest firmware
version via a standard PC. The latest firmware can be downloaded at
http://www.alphatech.cz/ipdp-firmware/firmware.htm.
All necessary steps for this process can be found on page 30. We strongly
recommend using the latest firmware version, which brings new features and
solves various possible issues of the continuosly improving Fermax door
phone panel. At www.alphatech.cz you can also find the latest version of
user and installation guide.
Manual version V3.1 8-4-2010
Valid for firmware of the VoIP module - V1.35
Contents
1
BASIC DESCRIPTION ...................................................................................................................... 4
FEATURES ................................................................................................................................... 4
USED TERMINOLOGY .................................................................................................................. 5
ASSEMBLY OF PANELS ................................................................................................................ 6
1.3.1
Terminology and orientation in panels ................................................................................. 6
1.3.2
Examples of panels ............................................................................................................... 7
1.4
CHARACTERISTICS OF THE MODULES .......................................................................................... 9
1.4.1
The basic module of electronics Fermax PBX DP................................................................. 9
1.4.2
Example of switches connection .......................................................................................... 13
1.4.3
Front panel ......................................................................................................................... 13
1.4.4
Exchange of visit cards ....................................................................................................... 14
1.4.5
Camera ............................................................................................................................... 14
1.4.6
Expansion module Fermax PBX EXP ................................................................................. 14
1.4.7
Keypad module Fermax PBX KEY ...................................................................................... 16
1.4.8
Other modules (panels) ....................................................................................................... 16
1.5
ASSEMBLY OF THE DOOR PHONE PANEL.................................................................................... 17
1.5.1
Surface mounting ................................................................................................................ 17
1.5.2
Flush mounting ................................................................................................................... 17
1.1
1.2
1.3
2
DOORPHONE VOIP OPERATION ............................................................................................... 18
2.1
2.2
2.2.1
2.2.2
2.3
2.3.1
2.3.2
3
SIGNALING OVERVIEW ............................................................................................................. 18
VISITOR AT DOOR ..................................................................................................................... 18
DoorPhone without Keyboard ............................................................................................ 18
DoorPhone with Keyboard ................................................................................................. 19
PERSON INSIDE OBJECT ............................................................................................................ 20
Outgoing Call ..................................................................................................................... 20
Incoming Call ..................................................................................................................... 20
PROGRAMMING OF PARAMETERS ......................................................................................... 21
BASIC VOIP SETTINGS .............................................................................................................. 21
3.1.1
Choosing a mode and login................................................................................................. 21
3.1.2
Language option ................................................................................................................. 23
3.1.3
Network settings .................................................................................................................. 23
3.1.4
Peer to peer or SIP server connection ................................................................................ 25
3.1.5
Audio codec setting ............................................................................................................. 25
3.1.6
Setting video........................................................................................................................ 26
3.1.7
Viewing the video (programme PopUp) .............................................................................. 27
3.1.8
Day intervals ....................................................................................................................... 28
3.1.9
User interface ..................................................................................................................... 28
3.1.10
Service settings .............................................................................................................. 29
3.2
SETTING DOORPHONE PARAMETERS ........................................................................................ 31
3.2.1
Basic Parameters ................................................................................................................ 31
3.2.2
All about relays ................................................................................................................... 32
3.2.3
Time Parameters ................................................................................................................. 34
3.2.4
Direct Dialing – Memories ................................................................................................. 35
3.1
4
TECHNICAL PARAMETERS ........................................................................................................ 36
4.1
4.2
4.3
ELECTRICAL PARAMETERS ....................................................................................................... 36
MECHANICAL DIMENSIONS ....................................................................................................... 36
PARAMETERS OF VIDEO ............................................................................................................ 36
IPDP - installation and operating instructions
3
1 Basic description
1.1 Features

























4
IP (SIP) modular system with built-in colour camera
P2P or SIP proxy mode (PBX network system)
1-64 pushbuttons
Two 25-digit numbers on each pushbutton
Waterproof pushbuttons with impregnation IP66, gold plated contacts
Pushbuttons are manufactured in zamak and a natural chromed finish
Panel is made of highly weather resistant anodized aluminium
Easy installation for outdoor or indoor use
Pernament card slot lighting
Card slot lighting by low consumption, max. duration LEDs
2 relays for two independent electrical locks
Codelock feature by using pushbuttons
Up to six codelock numerical passwords (2-6 digits)
Basic panel set is supplied in 2 pushbutton version with colour camera
and surface mount installation box (ref. 1CP201 + ref. F7061)
Basic panel ref. 1CP201 contains the first expansion module for 8
pushbuttons
Power supply 12V or PoE (Power over Ethernet)
PoE allows using a low consumption el. lock
PopUp SW for on-line monitoring of door entrance, possiblity to open
el. locks via PC
WEB based programming
Integrated heating of the electronic circuit board
OS Linux 2.6
USB connection of integrated camera – USB Guest 1.1
Software GSPCA for video transmission to web browser in PC –
W3CAM (J-PEG, RTSP stream) and stream H.263
Flush or surface mounting
Automatic illumination for camera by white LEDs
IPDP - installation and operating instructions
1.2




















Used terminology
Ethernet is a family of frame-based computer networking technologies for local area
networks (LANs)
LAN - a local area network (LAN) is a computer network covering a small physical
area, like a home, office, or small groups of buildings, such as a school, or an airport
10Base-T – 10 Mbit/s, it uses 8 position modular connectors, usually called RJ45 in
the context of Ethernet over twisted pair. The cables usually used are four-pair
twisted pair cable (though 10BASE-T and 100BASE-TX only actually require two of
the pairs). Each of the standards support both full-duplex and half-duplex
communication. According to the standards, they all operate over distances of up to
100 meters
100Base-TX – so called Fast Ethernet, two pairs of UTP or STP cable, category 5
Twisted pair cabling is a type of wiring in which two conductors (the forward and
return conductors of a single circuit) are twisted together for the purposes of
canceling out electromagnetic interference (EMI) from external sources; for instance,
electromagnetic radiation from unshielded twisted pair (UTP) cables, and crosstalk
between neighboring pairs
UTP, Unshielded Twisted Pair
STP, Shielded Twisted Pair – the cabling includes metal shielding over each
individual pair of copper wires. This type of shielding protects cable from external
EMI (electromagnetic interferences)
WEB - World Wide Web (WWW, or web) – a world-wide application of HTTP
internet protocol
HTTP (Hypertext Transfer Protocol) is an internet protocol used originally for
exchanging hypertext documents in HTML format
USB (Universal Serial Bus) – modern way of connecting external devices to the
computer
Video codek („coder and decoder“) - compression H.263 is derived from MPEG-4,
H.264 is a coder for MPEG-4 AVC format. MPEG-4 is a type of video compression –
decreasing of data stream video sequence
JPEG is a standard method of loss compression used for saving digital images
Voice over Internet Protocol (VoIP) is a technology enabling transmission of
digitalized voice inside the packej of protocols family UDP/TCP/IP via komputer
network. I tis used for making phone calls via Internet, Intranet or any other kind of
data connection
TCP/IP contains a set of protocols for communication in the computer network and it
is the main protocol of Internet
IP address is a number, which clearly identifies a network interface in the computer
network, which uses IP protocol
DHCP (Dynamic Host Configuration Protocol) is an application protocol from the
family of TCP/IP. It is used for automatic assigning of IP addresses to individual
personal computers in the PC networks, thus simplyfing their administration
Internet is a word-wide system of mutually connected computer networks
Intranet is a computer network similar to Internet, but it is a private one. That means
it is just used for small user groups (e.g. employees of a company)
PoE (Power over Ethernet) is powering via data network cable, with no need of
bringing the power supply via a separate cable
NTP (Network Time Protocol) is a protocol for synchronization of internal computer
clock
IPDP - installation and operating instructions
5
1.3 Assembly of panels
The building blocks of Fermax IP DP are the basic panels which differ by
its size, number of pushbuttons, if the visit card has got two or one
pushbuttons.
1.3.1 Terminology and orientation in panels
4 CP 204 (item number) as a representative of terminology. It is a panel with
height of 199mm. It contains an audio module, a colour camera and two times
4 pushbuttons, i.e. 8 pushbuttons in total.
first digit: 1 - 9 defines the height of the whole panel, the width of all panels is
130mm.
1 - 128mm
2 - 151mm
3 - 175mm
4 - 199mm
5 - 246mm
6 - 294mm
7 - 341mm
8 - 389mm
9 - 436mm
group of letters: defines basic HW features of panel :
A - audio panel
C - audio panel with a camera
P – panel with pushbuttons
V – panel with a window
W- panel with two windows
first digit after letters:
1 / 2 – defines number of pushbuttons at visit card
1 (on the right) or 2 (on the left or right)
next two digits:
01 - 15 – number of visit cards. If multiplied by the
previous digit, then we get a number of pushbuttons on
the panel
By this marking one compact panel is defined. The panel can be expanded by
other panels vertically or more optimally, in a horizontal direction. In case of
horizontal expansion, then it is necessary to use the same height of panels
(defined by the first digit of the item number).
6
IPDP - installation and operating instructions
1.3.2 Examples of panels
Fermax IP DP
1 AP 201
Fermax PBX EA
1A
Fermax IP DP
2 AP 202
Fermax IP DP
1 AP 101
Fermax IP DP
1 CP 201
Fermax IP DP
1 CP 101
Fermax PBX KEY
1
Fermax IP DP
2 AP 201
Fermax IP DP
2 CP 202
Fermax IP DP
2 CP 102
All panels can be mounted either on the surface or they can be flush mounted.
In the latest catalogue of Fermax you can choose the correct New Cityline
accessories incl. for example the protective roofing.
IPDP - installation and operating instructions
7
Fermax IP DP panels can be equipped with an additional
time switch called "TimeRelay". It is used for an expansion
of the number of switches. It is programmable. Based on
switching of one of the two switches in the Fermax IP DP
panel, the TimeRelay can simulate e.g. sequent opening of
the door or alternatively you can connect the exit button.
8
IPDP - installation and operating instructions
1.4 Characteristics of the modules
1.4.1 The basic module of electronics Fermax PBX DP
The basic module of Fermax IP DP panel is supplied in two versions –
with two pushbuttons - Fermax IP DP-2 (a version for 1 or 2 pushbuttons) and
two pushbuttons with a possibility of expansion by additional 8 pushbuttons, i.e.
each basic panel allows connection of up to 10 pushbuttons with no further
accessories of Fermax IP DP panel. The basic module can be further
expanded by additional 8 pushbuttons via modules called Fermax PBX DP
EXP and a keypad module called Fermax PBX KEY.
Picture 1 Schematics of connection and set-up elements
IPDP - installation and operating instructions
9
Picture 2 The real image of connection and set-up elements
1.
2.
3.
4.
5.
PoE module – the Fermax IP DP panel is equipped by a circuit supplying
the power over UTP cable – PoE. If your network switch is equipped by
PoE, or if you have got a PoE power supply (a box in the size of a power
supply adapter inserted into the input of the UTP cable), then for the
correct function of the door phone panel you do not need an external
power supply of 12V. If you use an electrical lock for opening the door,
then you need to use an external power supply adapter (only in the circuit
with relay contacts). You can also use a lower power consumption
electrical lock. In this case please use the connector on IPNCmod 12V.
When the door phone panel is PoE powered, there is 12V/350mA
available.
Yellow LED – signallisation of active power supply
Yellow LED – data activity on the network connection (continuous light
during data transmission)
Green LED – network connection (Ethernet) – continuous light in case the
UTP cable is connected correctly.
Loudspaker loudness SPK – by the trimmer you can set a desired
loudness of the loudspeaker. In case you need to further increase the
10 IPDP - installation and operating instructions
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
power output of the loudspeaker, you can use an add-on module with an
amplifier Fermax PBX EA.
Loudspeaker connection SPK
Microphone connection MIC - attention on the right polarity!!!
MIC loudness setting – by the trimmer you set the desired level of loudness
of the microphone.
Settings of Echo cancellation. Fermax IP DP door phone panel is a handsfree telephone. During the phone call the signal from a loudspeaker comes
back to the microphone and it comes with a delay to the calling party (that
is caused by a digital conversion and transmission of the signal). For this
reason the door phone panel is equipped by an echo cancellation circuit. It
is neccessary to pay more attention during the setting of the echo
cancellation circuit. The right setting of echo cancellation means at what
level of sound the mic turns off in Fermax IP DP in order to avoid returning
the delayed sound.
Setting of sensor sensitivity on surrounding light. It is valid only for
modules equipped with a camera. If case the surrounding light decreases
below at certain level (it is set by this trimmer), then the camera is
equipped by a white LED diodes for extra illumination. These LEDs are
activated during a phone call only.
Green LED – it signals an outgoing call (the door phone panel calls the
destination number or IP address)
Yellow LED – it signals an incomming call (there is a call comming to the
door phone)
Ethernet connection (UTP cable) – a connection to the computer network.
If you have got a network switch with PoE or a PoE power supply (a box in
the size of a power supply adapter inserted to the input of UTP cable), then
you do not need an extra power supply for operation of the door phone
panel.
DIP switch – setting of default values and the mode of Fermax IP DP door
phone via a DIP switch.
1- reserve (unused)
2- mode switching P2P / SIP server
3- basic settings – resets all values to factory settings
except for the memory of numbers
4- sets the starting IP address to 192.168.1.250
All changes show always after turning off and turning on
of the power supply (restart).
The DIP switch 3 and 4 needs to be switched back to
„on“ position after the start of VoIP module. Otherwise after the restart the
set parameters or the new IP address are rewritten back to the default
mode.
Output of 12VDC (max. 350mA!). This output is used primarily for
supplying the power to the lowconsumption electrical lock when PoE is
used.
IPDP - installation and operating instructions
11
16. Switching contact 2 (NO= normally open, NC= normally closed and COM=
common output of the switch).
17. Connector 8 – for connecting 8
pushbuttons (integrated expansion). For
connection
please
use
an
interconnection cable Fermax PBX
CC8. Each colour of the cable is
assigned exactly for
a specific
pushbutton – see picture 3.
Connection of pushbuttons:
blue
= 3rd pushbutton
Picture 3 Cable Fermax PBX CC8
brown
= 4th pushbutton
yellow
= 5th pushbutton
red
= 6th pushbutton
white
= 7th pushbutton
green
= 8th pushbutton
orange
= 9th pushbutton
black
= 10th pushbutton
The numbers of pushbuttons begin with 3, because the first two buttons
are integrated on the basic panel.
18. Connector 5 – connection of the 8-pushbutton expansion Fermax PBX
EXP or the keypad Fermax PBX KEY. The connection is done via Fermax
PBX CC5 cable. It is a data connection only. Power supply of illumination
and the common output is on the Connector 3.
19. Connector 3 – it is used for connection of the power supply and the
common output of the pushbuttons. The original Fermax cable is used
(Fermax PBX CC3).
20. Jumper Light enables switching on/off the illumination of visit cards.
21. Switching contact of the 2nd switch (NO=normally open, NC=normally
closed and COM=common output of the switch).
22. When using Fermax IP DP, it is suggested to use either an alternating
power supply voltage min. 10VAC – max. 15VAC or a direct power supply
voltage min. 12VDC - max. - 18VDC. which is connected to the connector
"12V". The load of the power supply depends on the number of modules
used, because it is used also for powering the illumination of visit cards – if
the max. number of pushbutton panels is used, the power consumption
does not go beyond 500mA. This power supply can be also used for
powering the electrical locks, then you need to calculate alsko with the
power consumption of electrical locks. Usually it is enough to use a power
supply of 12VAC/1A÷2A.
12 IPDP - installation and operating instructions
1.4.2
Example of switches connection
The switching contact of relay is separated galvanically from other circuits of
the door phone panel.
When using PoE, the output of 12V is connected galvanically with the
PC network. Therefore when using PoE power supply, please pay
attention during manipulation and installation. The circuit is connected
galvanically with the computer network!!!
1.4.3 Front panel
1. Assembly openings for mounting
of the front panel. After installation
of the top opening, please cover it
with the plastic cover with Fermax
logo. When bottom opening please
cover with the grey, round plastic
cover. Both covers incl. the screws
are part of delivery as accessories.
2. Loudspeaker.
3. Camera with illumination and a
sensor for switching on the
illumination.
4. Pushbuttons.
These
two
IPDP - installation and operating instructions
13
pushbuttons can be found on the basic electronics module (the main PCB).
In case you use a panel without these first two pushbuttons, then please
leave them out during the programming process (pushbuttons 1 and 2).
5. Visit card. The exchange of visit card is described later on in the manual.
The visit card is illuminated by white LEDs (they can be switched off). You
can also find a red LED under the visit card – it is used for signallisation of
the door phone panel status.
6. Microphone.
1.4.4
Exchange of visit cards
The visit cards are disassembled from the front of
the door phone panel as shown on the picture.
Please use a tool carefully, do not damage the
front panel or the cover of visit cards. The cover
of visit cards is a tub into which you place the
paper with descriotion (the visit card).
1.4.5
Camera
The module of colour camera is
integrated into the panel of Fermax by a
sub-board with mounted LED illumination
and a sensor of surrounding light.
1. Camera module
2. The main board of the camera - 3
LEDs for illumination
3. Mounting column for the main board
4. Sensor of surrounding illumination
5. Mounting of the main board
1.4.6 Expansion module Fermax PBX EXP
The expansion module has got two connectors 5, one is used for connection
towards the basic module (Fermax PBX DP)
and the second one is used for connection
of the following module. For interconnection
please use cable Fermax PBX CC5.
Besides connectors 5, you can also find on
the expansion module the connector 8 for
connection of the pushbuttons. For
interconnection please use the cable
Fermax PBX CC8. Each colour of the
cable is assigned exactly to the specific Picture 4 Cable Fermax PBX CC8
pushbutton, see picture for more details.
14 IPDP - installation and operating instructions
Connection of pushbuttons:
Position number on Fermax PBX EXP
Colour of wire
1
2
3
4
5
6
7
Blue
11 19 27 35 43 51 59
Brown
12 20 28 36 44 52 60
Yellow
13 21 29 37 45 53 61
Red
14 22 30 38 46 54 62
White
15 23 31 39 47 55 63
Green
16 24 32 40 48 56 64
Orange
17 25 33 41 49 57
Black
18 26 34 42 50 58
The numbering of positions is shown on the picture 5. All numbers of
pushbuttons refer to the settings of the door phone panel (see more in the
programming section).
Picture 5 Connection of expansion modules
IPDP - installation and operating instructions
15
1.4.7 Keypad module Fermax PBX KEY
The keypad module is connected via a cable Fermax PBX CC5 and a cable
Fermax PBX CC3. The connection is similar to the connection of the expansion
module. The difference is that the keypad module is always the last in the row
(you cannot connect to the keypad module any other module). The keypad
module can be only connected to the second position (i.e. directly to the basic
module) or to the third position (to the output of the first Fermax PBX EXP
module). Attention – 1st position can´t be used because the first position
is occupied by the fixed expansion on the basic module (pushbuttons 310). This means that besides the keypad you can use 0 – 18 pushbuttons with
the direct dialling (depends on the specific configuration).
Please pay attention during programming – you need to specify correctly to
which position the keypad is connected.
Dialling is realised by a sequent pushing of number
pushbuttons. When entering a password, you need to press
the B pushbutton. To hang up, please press the pushbutton
A and the door phone panel hangs up.
1.4.8 Other modules (panels)
All other panels can be found in the offer of your local partner.
16 IPDP - installation and operating instructions
1.5 Assembly of the door phone panel
1.5.1
Surface mounting
For surface mounting we offer a compact installation box.
The installation box is mounted with screws with plugs to
the wall. On the picture you can find an installation box,
size 1.
1.5.2 Flush mounting
Flush mounted installation boxes are
refered to as “MKxx” or simply “flush
mount installation boxes”. When using the nearly
square flush mount installation box MK1, please pay
attention on the correct orientation of the mounting
holes – they need to be on the vertical axis. The
correctly mounted installation box is shown on the
picture.
1. Preparing installation box
2. Principle of connecting
boxes next to each other
installation
3. Placing the installation box above
the ground
IPDP - installation and operating instructions
17
2 DoorPhone VoIP Operation
2.1 Signaling Overview
The all-purpose guard signals an acoustic conditions they may occur
during operation. Another signaling can be done by means of red LED (placed
under first label).
Condition
Tones
Tone frequency
LED
Line lifting up
–▄–■–▀–
425-850-1275
glows
Line hanging up
–▀–■–▄
1275-850-425
goes
out
Report after calling
–▄–■–▀–
425-850-1275
glows
Notice about call end
–■–■–■–
1275
glows
Parameter confirmation
––█––
glows
–■–▄–■–
1275-850-1275
Error (anything, if unsuitable)
–■–■–■–■–■–■–
425….
Empty memory (no progr. numb.)
–█–▄–■–▄–■–▄–
850-1275-1700…
Switch on (Reset)
blinks
2.2 Visitor at Door
The all-purpose guard function is influenced partly by used guard
assembly (with keyboard or without it) and partly by setting of guard
parameters.
2.2.1 DoorPhone without Keyboard
The DoorPhone buttons are provided by nameplates or positions of
persons inside the object. The incoming person will press the corresponding
button, the DoorPhone will lift up the VoIP canale neither immediately (the
button is not the first number from code lock), or with delay and dial the
programmed phone number thru VoIP, but dial number differs by choice mode,
which is set in the DoorPhone :
- Day/night mode = being the DoorPhone in Day mode, so it is always
dialing a number set in table 1, in Night mode, it is always dialing a
number set in table 2.
- mode two number group = first press – it always dials a number set
in table 1. By repeated press of the same button or detection of busy
tone after dialing the DoorPhone will select the number from the
second group (table 2). The next press of the same button again
selects a number of the first group, etc..……
The switch (code lock) can be controlled by first 10 buttons of
DoorPhone. If the visitor at door presses buttons in such combination that meet
the preprogrammed code and the time among presses is not bigger than the
18 IPDP - installation and operating instructions
set point, then the DoorPhone will pick up and close the corresponding switch
(if set in m=1 or m=5 modes) to the period given by seting in parameters. Then
it will hang up.
2.2.2 DoorPhone with Keyboard
The DoorPhone with keyboard can also include besides
the keyboard up to 16 buttons of direct dialing always
behaving as to be mentioned in 1.4.7(page 16) except the
code lock. This one is always situated on keyboard. After
keyboard is connected, the position, where the keyboard is
connected to, should be set in programming parameter.
The keyboard has two functional buttons – B symbol =
once pressing the numerical combination is considered as the combination for
control of the switches. The second button – A symbol = when pressing the
DoorPhone immediately will hang up.
The number selection on keyboard can be executed in two ways:
- The incoming person is dialing number as to be done on phone – the
period among button presses should be lower than the value given
by programming parameter. After this period the DoorPhone will lift
up and dial the given number.
- On buttons the incoming person is dialing a two-digit number (from
01 to 64), which represents the memory number, where the 16-digit
number is stored (same as for buttons). The number dialing is
managed by Day/Night setting or mode for two groups of numbers
(as described in chapter 2.2.1 page 18).
IPDP - installation and operating instructions
19
2.3
Person Inside Object
The person inside object is considered a person that is in phone contact
with DoorPhone.
2.3.1 Outgoing Call
The outgoing call is the call from DoorPhone (caused by visitor). After
guard choice the telephone is ringing inside object and the pickuping up will
allow speaking to the visitor at door. The code choice can close the switch, if
set to m=1 or m=5 modes, change over the Day/Night modes and hang up the
DoorPhone. The DoorPhone in 10 seconds before call end will send a notice
about call end and the call may be extended by sign selection (* or #). The
telephone hanging up will end the call.
They are two possible means transmission information of push
buttons (command for opening lock, switch-over day/night, prolongation
conversation, command for hang-up) - by either in "RTP channels" or in
"SIP info", variant "inband DTMF" isn't in IPDP decoding.
2.3.2 Incoming Call
The incoming call is the call to the DoorPhone (caused by person inside
object). After exchange number selection, where the DoorPhone is connected,
the DoorPhone is ringing and when set number of rings is over, the DoorPhone
will pick up and it is possible to speak. The possibilities are the same as with
outgoing call.
20 IPDP - installation and operating instructions
3 Programming of Parameters
3.1 Basic VoIP settings
3.1.1 Choosing a mode and login
It is important to choose a DoorPhone mode
first. The DoorPhone can work in the PeerToPeer
mode or SIP server mode. The mode setting can be
made by a relevant switch (DIP switch see on Pict. 9).
In the SIP server mode is possible to choose SIP
server (external). It can be set in a configuration
interface of the DoorPhone.
Setting values in doorphone to the firm setting
make by DIP switch 3 move to the position off and
reboot doorphone. After reboot system this switch is
necessary return to the position On.
Setting of basic IP address
192.168.1.250 make by DIP switch 4
Pict. 1 DIP switch setting
move to the position off and reboot
doorphone. After reboot system this switch is necessary return to the position
On.
Reboot doorphone it is possible make by double ways – partly turn it off
and on again, or clicks on „Restart", in WEB site is at the entry service.
IP address of doorphone is from the manufacturer (as well as default)
setting on 192.168.1.250. If you are at installation in other numbering nets (=
NOT BEGINING 192.168.1.xxx) so is necessary setting in feature of protocol
TCP/IP in your PC IP address either temporarily or like alternative configuration
e.g . 192.168.1.245 . Then it is possible setting parameters of doorphone
including new IP address and after reboot VoIP module in doorphone you can
attach to WEB sites of the doorphone already on new IP address.
ATTENTION: DIP switch 3 and 4 must be in position "On", otherwise new IP
address after reboot module is re-write back on starting IP address =
192.168.1.250.
IPDP - installation and operating instructions
21
In your web browser enter IP address of the DoorPhone, default is
192.168.1.250. See Pict. 2.
Pict. 2 First site - video from camera
Enter user name and password. User name is „admin“, default password
is „1234“. See Pict. 3.
Pict. 3 Login to setup
22 IPDP - installation and operating instructions
3.1.2 Language option
Language setting can be made in a menu on the left panel.
3.1.3 Network settings
Network settings are located in the Network seting menu item. It is possible to
use DHCP service (1) or you can enter IP addresses manually.
Manual configuration:
After making changes click on a save and restart button.
1. Hostname – name of doorphone for resolution in nets (e.g . while using
more doorphones – more entrance)
2. Enable/disable ethernet settings via DHCP
IPDP - installation and operating instructions
23
3. Setting IP address, mask, eventually next network parameters, in case
obscurity contact his IT manager
4. Display actual mode of IPDP – day / night
5. Return on introductory WEB site with display videos from cameras IPDP
6. short help for quick assistance in setting the parameters1 –
7. Default value – presetings to the firm settings. After making changes click
on a save and restart button (display screen - see page 29).
DHCP configuration:
After making changes click on a save and restart button.
1. Hostname – name of doorphone for resolution in nets (e.g . while using
more doorphones – more entrance)
2. Enable/disable ethernet settings via DHCP
3. DHCP client ID is name, which using for assigning two IP address to only
thing the MAC address (in IPDP porter has meaning as far as will be
including internal SIP server)
4. display parameters automatically assign by DHCP - IP address and next
setting
5. Default value – presetings to the firm settings. After making changes click
on a save and restart button (display screen - see page 29).
Important: if you use setup via DHCP, then it‘s assigning IP address to
DoorPhone automatically and network administrator must tell you actual
address, to was possibility display video in web browser. Because assigning IP
adress can change after e.g . failure power supply in object, so they
recommended enjoy DoorPhone with fixed IP address.
24 IPDP - installation and operating instructions
3.1.4 Peer to peer or SIP server connection
The DoorPhone can be set to the peer to peer (P2P) mode or to the SIP server
mode by DIP switch (page 21). In P2P mode DoorPhone calling IP adress – in
memory buttons (page 35).
If you setting SIP server mode by DIP switch, so add in menu item SIP
parameters
After making changes use the save changes button.
1. SIP proxy server IP adress or the SIP server name and port (usually 5060
or 5061)
2. Registering data to SIP proxy server (aren't obligatory)
3. Expiration is interval of sending requests for re--registration in SIP server
4. Default value – presetings to the firm settings. After making changes use
the save changes button.
3.1.5 Audio codec setting
IPDP - installation and operating instructions
25
After making changes use the save changes button.
1. There is choosing only priority using audio codecs, used codec is selection
automatically at make audio connection in SIP protocol.
2. Default value – presetings to the firm settings. After making changes use
the save changes button.
3.1.6 Setting video
After making changes use the save changes button.
1. Resolution display video
2. Number picture per second (frequency restoring picture)
3. Setting next parameters of camera
4. Default value – presetings to the firm settings. After making changes use
the save changes button.
26 IPDP - installation and operating instructions
3.1.7 Viewing the video (programme PopUp)
Video in doorphone IPDP is capture by USB WEB camera. Picture from
camera is sending partly like series JPEG pictures to the environment WEB
browser (first page on IP address IPDP doorphone) and second method is, that
IPDP sending stream video in coding H.263 and in future H.264. This stream
video is possible watch e.g . on telephone Grandstream series GXV3000,
which has big LCD display.
Next interesting way watching videos from IPDP is install PopUp program
UDVGUARD for Windows. This programme also with manual is freely
download on http://www.alphatech.cz/engl/e_ipdp.htm. Programme except
display the video has even this interesting functions:
- at conversation IPDP is program automatically activate from system tray of
Windows to the foreground and display picture from IPDP, after
termination talk again minimalize (function PopUp)
- makes it possible switch on by click both relay in IPDP – opening door
- makes it possible acoustic connection with IPDP – if doorphone call on
address PC with installed and running programme, so it is possible receive
conversation from IPDP through the medium sound card in PC. Click on
button DoorPhone in program it is possible reversely call to IPDP
- programme it is possible install to the max.100 computers in net, if is
active connection with IPDP, so to all computers with running program
maximize window with displayed video. In programme is adjust IP address
of doorphone, thereby it is possible in one nets operate more Slim IPDP
and to which IPDP programme is coresponded individual "Hostname"
setting to page.23 and this Hostname is displays in header of programme
PopUp.
Parameters of video is on page 36
IPDP - installation and operating instructions
27
3.1.8 Day intervals
After making changes use the save changes button.
1. Display actual internal time (you must setting in "Service" time server)
2. Table of time interval - interval is meaning where is day, the rest is night.
For example: interval 1 = 08:00-12:00, interval 2 = 14:00-17:00 - from
00:00 to 7:59 is night, from 8:00 to 12:00 is day, from 12:01 to 13:59 is
night, from 14:00 to 17:00 is day and from 17:01 to 23:59 is night.
3. Default value – presetings to the firm settings. After making changes use
the save changes button.
3.1.9 User interface
After making changes use the save changes button.
28 IPDP - installation and operating instructions
1. Possibility switch off displaying videos on start page - safety device
2. Possibility switch off video in VoIP call (video in call makes at some
systems problem)
3. Possibility change port from conventional 80 to other
4. Possibility disable / enable access over telnet
5. Default value – presetings to the firm settings. After making changes use
the save changes button.
3.1.10 Service settings
1. display current version of firmware in module VoIP and in module
doorphone. Button "Basic LOG" or "Extended LOG" displays to the what
state LOG switch, it means you see "Extended LOG" so they switch to the
IPDP - installation and operating instructions
29
basic LOG and back to, in short switch you have such LOG, which don't see
writing on button.
2. Click on "Download log file" file save to you choice place. File has extension
".BIN", this is necessary rename on ".TAR". To unpacking archive "tar" use
e.g . programme "PowerArchiver". File from file equip extension ".TXT". Last
notice is thereon, that the text file hasn't standard ending rows. To safe
display get past e.g . programme "PSPad".
3. Click on "Show call log" will display history of call for SIP - only call
instructions.
4. Click on "Show VoIP log" start VoIP monitor - log file which is running in
new browser window - online displays events.
5. Time server is IP adress of NTP server with time data (actual time in module
VoIP is displayed in "Day intervals")
6. Syslog server is IP adress of computer where is running syslog aplication
for collection network events
7. tool for upgrade firmware in module VoIP and in module doorphone,
switching automatic - information is in upload fille. Next in this tool is
possible change environment of WEB sites - colours, fonts, frames…
8. Addition / change language file - upload fille with language assignment
9. Save configuration - save actual setting in IPDP (all features)
10. Restore configuration - restores setting of all IPDP from file previously
storage configuration
11. Change access password, default is 1234
12. Reboot VoIP module.
30 IPDP - installation and operating instructions
3.2 Setting DoorPhone parameters
3.2.1 Basic Parameters
After making changes use the save changes button.
1. Mode of DoorPhone choice selects number per Day/Night DoorPhone
mode or selects numbers of the first and second groups.
2. Sign for call extension * or # (10sec before call end the DoorPhone will send
a notice, then the call may be extended)
3. Two commands in order to hang up the DoorPhone using both switches
[2 digits].The advantage is to set the same command both for switch closing
and command to guard hanging up (page 32).
4. Command for DAY / NIGHT mode switching
Note: The switchover to Day/Night mode remains set in IPDP even after
power supply disconnection.
5. Automatic or manual switching Day - Night mode. Automatic switch setting
in "Day interface".
6. Dialing as on normal telephone (all number of called person should be
pressed on keyboard). If use mode P2P then “.” in IP adress is make by
push to button with “key”
Only 2-digit memory number is entered on keyboard by which the number
of called person is stored (memory number corresponds to button number
with respect to Day/Night switchover).
7. =0 only NC-module connected to the basic module
=1 not use
=2 the keyboard connected on the first position
IPDP - installation and operating instructions
31
=3 the keyboard connected on the second position (explanation of position
keyboard is on chapter 1.4.7(page 16).
8. Default value – presetings to the firm settings. After making changes use
the save changes button.
ATTENTION! This parameters setting will sharply influence whole DoorPhone
function.
3.2.2 All about relays
After making changes use the save changes button.
1. Relay mode:
=1 switch mode – it will close on command or password for period t1/2
(used for electrical locks, gate opening etc.)
=2 camera mode – it will close by guard pick up and open by hanging up.
=3 lighting mode – it will close by guard pick up and stay closed even for
period t1/2 after guard hanging up.
32 IPDP - installation and operating instructions
=4 bell mode – it will close after button pressing and open after period t1/2
(used for e.g. external bell or horn connections).
=5 gradual opening mode – in this mode the only relay 2 will be set
together with relay 1 set to mode 1. The relay 1 is activated for period t1,
then the time t3 is proceeding before relay 2 closing. Then the relay 2 is
activated for t2 period and afterwards the DoorPhone hangs up.
Note: The only relay 1 can be activated from phone and all sequence started.
Besides that the relay 2 can be separately activated from buttons by password.
2. password for relay closing from buttons or keyboard [2 to 6 digits]. Total 6
passwords, they are controlled by Day/Night; the combination is entered
either by DoorPhone buttons (first 1/2 buttons) or from attached keyboard
(after pressing of key symbol). The relay closing influences the set switch
mode and Day/Night switchover. By setting of choice mode of 2 number
groups the DoorPhone is permanently in DAY mode.
By password choice some rules have to be observed:
 Select passwords in way not to find its combination out from
wear of certain buttons by frequent use.
 Select the first password button from frequentless button for
direct dialing (-extends choice time)(-not valid for keyboard).
 Pay attention to congruity of password numbers when one
password includes other one, e.g. relay 1 has 1212 and relay 2
has 12121. Then after second pressing button 2 the only relay
1 is called, but password choice 212 for relay 2 can call both
relays after secon pressing button 2.
3. Command from phone after relay closing [2 digits]. The same command can
be set for both relays, then they are activated at the same time. The
advantage is to set the same command both for relay closing and command
to DoorPhone hanging up (page 31).
4. Duration of relay closing in second [2 digits 01-99]
5. To prohibit the control during incoming call is important e.g. when using
relay 2 in mode 1 for control of garage gate opening, when the electronics
opens the gate and the gate is closed by car passage. Then the control
from phone could undesirably cause the permanent gate opening (not
closed – no car passage).
6. time in second between close relays 1 and 2 by mode setting of relay 2 is 5
(gradual opening) [2 digits 01-99]
7. Default value – presetings to the firm settings. After making changes use
the save changes button.
IPDP - installation and operating instructions
33
3.2.3 Time Parameters
After making changes use the save changes button.
1. max. time, for which the DoorPhone is hanging up, this time can be
extended during call by sign choice from telephone (* or #) – see page 31.
2. Number of incoming call rings, the DoorPhone pick up after preseted
number of rings. After detection first ring – LED on front panel blinking. The
number can be set from 1 to 9.
3. max. time [sec] among button presses [range 1-9]
switch closing – if time between two next presses is bigger than w time,
the code is not evaluated correctly.
dialing – if the button, we are pressing, is the first password number for
switch closing, so the choice is delayed by this w time.
4. time [sec] for which the guard will hang up, before repeated dialing (button
pressing during call or dialing, busy tone detection) [range 1-5]
5. after finishing the dialing it calculates time (ringing tones). If the number
exceeds time in second, it will hang up [range 10-99]. The dialing is
repeated in case, when the dialing mode of 2 groups is set.
6. In default is status of DoorPhone signalling acoustically. If signalling makes
problem, so this signalling pick up / hang up prohibited.
7. In default is status of DoorPhone signalling acoustically. If signalling makes
problem, so this signalling others tones prohibited.
8. Default value – presetings to the firm settings. After making changes use
the save changes button.
34 IPDP - installation and operating instructions
3.2.4 Direct Dialing – Memories
After making changes use the save changes button.
1. telephone number up to 16 digits, we want to store. The numbers are the
numbers of the first group or numbers of Day mode. In default setting is
table memoirs empty. While using setting P2P to the memoirs saves IP
address e.g . 192*168*1*250, where „*“ means „.“ , while using SIP proxy
server to the memoirs saves phone number e.g. 117.
2. telephone number up to 16 digits, we want to store. The numbers are the
numbers of the second group or numbers of Night mode. In default setting
is table memoirs empty. While using setting P2P to the memoirs saves IP
address e.g . 192*168*1*250, where „*“ means „.“ , while using SIP proxy
server to the memoirs saves phone number e.g . 117.
Note: The switchover to Day/Night mode remains set in DoorPhone even
after power supply disconnection.
3. Default value – presetings to the firm settings. After making changes use
the save changes button.
IPDP - installation and operating instructions
35
4 Technical Parameters
4.1 Electrical Parameters
Parameter
Value
Communication interface
VoIP protocol supported
Video
Band width
Power supply - adapter
- or PoE
Max. consumption
Max. voltage of switch contact
Max. current of switch contact
Operational temperature
Conditions
Ethernet 10BaseT, 100BaseTx
SIP
série JPEG, stream H.263 (H.264)
300Hz – 3400 Hz
12Vss ± 2V , 12Vst ± 1V
IEEE802,3af Altern. A+B
300mA
12Vss
48V
at I < 1A
2A
at U < 30 V
- 20 to + 70°C
4.2 Mechanical dimensions
Panel
valid for dimensions of
all ref numbers of all
panels with height 1
(series 1)
130(w)x128(h)
Flush mounted
installation box
Surface mounted
installation box
Weater protection
hoods
ref. F08843
ref. F7061
for one panel – ref.
F8400
115(w)x114(h)x45(d)
130(w)x114(h)x33(d)
135(w)x130(h)
for two panels – ref.
8408
265(w)x130(d)
4.3 Parameters of video
Video for WEB:
InternetExplorer - (series JPEG pictures) is using again and again repeated
http request ADDRESS/video.jpg
Mozilla, Opera, Firefox … and program PopUp (UDVguard) - (MJPEG
stream) is using http request ADDRESS/video.mjpg (sometimes it is necessary
reload beyond with it start).This video is continuously and has smaller load of
nets.
Stream video for IP phones:
H.263 IPDP doorphone and videophone communicate over SIP/SDP protocol
on standard SIP port and video (and sound) then run in RTP protocol on port
talk to SIP.
36 IPDP - installation and operating instructions
Guarantee conditions:
The product was shop-checked. The producer guarantees that this product will
keep the features described in these operating instructions in the course of
guarantee provided that the user will be handled with it as described in the
operating manual. The guarantee will be extended by period of possible
guarantee repair.
When claiming in guarantee period please contact your dealer. The producer
only will make the guarantee repairs. Attach the description of claim reason,
proof of purchase and your exact address to the product.
The guarantee does not include:
 mechanical, thermal, chemical and other damages caused by user’s
activities
 defects caused by natural disasters
 defects caused by repair or changes carried out by user or other
unauthorized person
 willful damage of product
 incorrect use of product caused by other use than specified in
operating manual (e.g. installation, programming)
 damages caused during product transport to customer and from
supplier
ALPHATECH TECHNOLOGIES s.r.o.
Jeremenkova 88, Praha 4, Czech Republic
www.alphatechtechnologies.cz
ALPHATECH TECHNOLOGIES s.r.o.
Jeremenkova 88
140 00 Praha 4
Czech Republic
VAT: CZ27577350
Company is registered in the Commercial Register
administered by the Municipal
Court in Prague, Section C, Record 116886
Banking details:
Komerční banka, account No. 43-7671450207/0100
IBAN: CZ0801000000437671450207
SWIFT: KOMBCZPPXXX