Wireless Pacific | X10DR | X10DR 2014 Brochure

Liberate Your Mobile Radio™
Secure Wireless Microphone
SINGLE/MULTIPLE
SEAMLESS INTEGRATION
WIRELESS TO 300+ METRES
MISSION CRITICAL DURABILITY
FH SPREAD SPECTRUM
TM
W I RE LESS PAC I F I C
A COSTLY HISTORY...
Since the creation of the first mobile two way radio, system designers and radio
manufacturers have grappled with solutions to enhance user mobility when
away from the vehicle. These solutions typically involved additional portable
hand-held radios and significant additions of base station infrastructure; radio
sites and complex remote receiver voting systems to back fill marginal coverage areas. Alternatively, some manufacturers developed cumbersome vehicle
based mobile repeater systems where simplex portable transmissions are repeated through a mobile repeater back into the base station network. These
systems required careful engineering, additional frequencies and critically
complex contention management protocols to eliminate clashing from multiple
vehicle repeaters at scene. Vehicle Repeaters usually added system delays
and required user intervention for managing which channels, mode or status
to use in order to make them work. Both solutions came at a cost... a big cost!
TIME TO GET LIBERATED!
- TALK IN OR OUT OF THE VEHICLE
- NEW ENHANCED EVR™ AUDIO
- SIMPLE INTUITIVE DESIGN
Accessory ports
Hirose 6 pin connector
3.5mm mono jack
X10DR Secure Mic
- MINIMAL USER TRAINING
(with XCFC)
- LIGHTWEIGHT & RUGGED
- SEAMLESS INTEGRATION - PATENTED INNOVATION
- INTELLIGENTLY PRICED
- SMART ACCESSORIES
- SECURE ENCRYPTION
- ALL DAY OPERATION
X10DR standard
shoulder mount
X10DR in X-Ponder
charger cradle
Side profile
60.... 150.... 300 Metres.
SECURE WIRELESS COMMUNICATION
via your vehicle’s mobile radio
Team Up
creating a safer place to work
X10DR Secure Wireless Microphone can be teamed up, when required, to provide dual or even triple user operation from a
single mobile radio. The smart node interface passes both transmit and receive audio to each X10DR ensuring each user hears
both active parts of the communications sent over the host two way radio channel.
Teams Remain Productive In Remote Work Environments
The vehicle mounted mobile radio is often the rural emergency worker’s sole communication link to central command and
other emergency units. However, when one team member needs to run back and wait at the vehicle, to provide or receive an
update, operations slow or at worst come to a stand still, losing time, productivity and placing lives at risk. X10DR is revolutionary technology, which allows emergency teams to stay in communication with each other onsite or back to base, via their
vehicle mounted mobile radio, up to hundreds of meters from the vehicle. Emergency workers can now stop working at trying
to simply communicate and just get on with saving lives.
Duress Alarm
The advanced model X10DR Secure Wireless Microphone naturally provide a duress button that can be used to activate the
emergency mode within the host mobile radio. Emergency workers can now call for assistance even while hundreds of meters
from their vehicle.
Headset Operation
Models are available which includes a 6 pin Hirose audio connector on its base as standard that allows use of industry standard audio accessories. Additionally, a mono 3.5mm headphone jack on every X10DR provides for quite
secured communications when silence is golden.
Long Battery Life
The X10DR’s 1200mA internal battery means you will typically achieve well in access of 24 hours operation between
re-charges. Docking the microphone into its cradle allows 100% re-charge from completely flat in less than 4 hours
or for a top up during a rest break.
WORKING SMARTER...
At Wireless Pacific we understand that what a product does to improve your work practices and employee safety,
is what really counts. This brochure provides an overview of the current available accessory range. The range of
X10DR accessories continues to grow, as we support creative implementation seeking to streamline their operational effectiveness. You can be assured we will continue to ensure X10DR is the right solution for every out of
vehicle mobile radio application.
Multiple Units
1 x XIB
1 x XMC-***
2/3 x XIB-CK
XIB & XIB-TA Interface Box
Each XIB & XIB-TA allows 2 or 3 X10DR’s to be connected to the one mobile radio. The XIB provides Emergency capability but the XIB-TA model
provides “off net” talkaround capability but cannot trigger emergency.
All units can hear each others communications as well as the conversations over the network. The interface unit connects to the host radio via
the XMC series interface cable. All XIB & XIB-TA units can also be casscaded to allow multiple X10DRs to connector to the one mobile radio.
Each X10DR with EVR™ connects to the XIB by way of short 50cm (20”) XIB-CK connecting cables. Note: Antenna placement is critical and should be ideally placed >50cm (20”)
from each other to minimize inter-unit interference.
Talkaround
1 x XFB-TA
1 x XMC-***
2 x XIB-CK
XFB-TA Talk-Around Function Box
The XFB-TA allows two X10DR to have local (talkaround) operation
where users can talk locally “off net” by using the orange side button as
a secondary PTT. To talk over the radio channel, the normal PTT button
is used. To activate Emergency, the user must first press the PTT and
then the orange button for >1 second.
The XFB connects to the host radio via a XMC series interface cable. Each X10DR connects to the XFB-TA via a XIB-CK cable.
Multiple Radios
Public Address
1 x XFB-MR
2 x XMC-***
1 x XIB-CK
XFB-MR Multi-Radio / Public Address Function Box
The XFB-MR can be used to allow 2 mobile radios to be connected to the
one X10DR unit. A unique marker tone* is attached to the tail of each
secondary radio reception to inform users which radio’s audio they just
heard. The XFB unit can be configured by way of a dip switch to either maintain the secure microphone’s emergency functionality on its
orange button, or to alternatively, use that button as a PTT to transmit on
the secondary channel. Alternatively, the XFB-MR second port can be
attached to the vehicle’s Public Address system to allow the user to talk
over the vehicle’s public address system by pressing the X10DR microphone’s orange button. To activate emergency in these two modes, the
user must first press the PTT and then the orange button for >1 second.
The X10DR connects to the XFB-MR by a XIB-CK connecting cable. The unit connects to
the host radio/s/PA via two XMC series interface cables. * Not compatible with radios
that cannot provide a COR/TOR/speaker unmute, etc output.
Lone Worker
XFB-LW Lone Worker Function Box
1 x XFB-LW
1 x XMC-***
1 x XIB-CK
The XFB-LW provides “lone worker” functionality to the X10DR. Dip
switches allow custom parameter setting for activity time interval (time
interval in which a user must momentary press their PTT or Emergency button), as well
as the user pre-alert tone interval (period where the X10DR user hears a warning
tone that an emergency condition is imminent). Momentarily pressing the PTT /
Emergency button will reset the imminent emergency condition. Additionally, a 10 Sec Live Mic feature can also be selected.
The XFB-LW connects to the host radio via an XMC series interface cable. The X10DR
connects to the XFB-LW by a XIB-CK connecting cable.
XFB-DP Function Box
1 x XFB-DP
1 x XMC-***
1 x XIB-CK
creating a safer place to work
The XFB-DP allows dual functionality of the orange side button. A short momentary press (<0.5Sec) can provide a unique
switched ground to a connected mobile I/O port, while a full 3 second press can be used to drive the radio’s emergency input
or other desired function. Use of the XFB-DP requires custom wiring of XMC interface cables. Other functions include:
i/ 145 or 260mSec Rx audio digital delay - Dip switch selectable.
ii/ A DB15 port with local on/off & emergency input/outputs.
If multiple XFB functions are required, contact your supplier for compatibility details.
Antennas
The XMAK antenna has been specifically designed and optimized for use
with X10DR and provides an optimal omni-directional 360 degree pattern.
The ground independent multi-polarity design takes advantage of 2.4GHz
multi-path propagation characteristics by picking up signals in both vertical, horizontal and any other reflected planes. The XMAK comes with 5.2m
(17’) low-loss LMR-200 (or equivalent) cable terminated with RP SMA male
connector, right angle mounting bracketor can be easily mounted on roof
racks, gutter mounts or any surface equipped to take the supplied N-male
stainless steel bulk head connector.
The XMMA is a unity gain magnetic mount 1/4 wave ground independent
antenna and comes with 3.5m (11’) of low loss LMR200 (or equivalent) coax
cable terminated with a RP SMA male connector.
Use of the 1 watt
XBDA is only approved
in FCC regulated and
other limited markets.
XMMA
XMAK
Complete with LMR-200 /
equiv. coax 5m/16’ terminated with a RP-SMA-M
and 90º mount and N typeF bulk head (loose)
Complete with LMR200/equiv.coax
3.5m/12’ terminated in
RP-SMA-M not shown
XBDA
Complete with 15cm
/ 6”coax tail 1m/39”
& DC power cable
not shown
The XBDA is a 1 watt Tx / 9dB Rx gain bidirectional amplifier with 15cm (6”)
RG174 coax tail and a 50cm (20”) lightweight DC power cable. It connects
between the X-Ponder RF output and the roof mounted external antenna.
(Use only where approved).
Audio Accessories
Wireless Pacific earpieces are designed for operational comfort day in day out. We use soft resilient polymers to ensure fatigue free, reliability
and hard wearing performance. Every X10DR provides a 3.5mm audio jack
so communications privacy can be discretely maintained at all times.
Both the advanced and basic X10DR (with the XHC option) provide an industry
standard compatible* Hirose® HR10-7R-6S type accessory port to allow
connection to motorcycle helmets, lightweight / heavy duty headsets, lapel
ear microphones, covert accessories and other radio application specific
audio accessories. X10DR provides a user selectable Mic gain function
by the user pressing the Volume Up button while powering up the Secure
Mic, or pressing the Volume down button when powering up to revert to
standard sensitivity. * most types - pre-test before ordering if unsure.
A variety of headset interface cables are available, in addition to custom
special order cable kits for large fleet implementations such as police motor cycle fleets. The WPSHC-HIR allows for simple connection to a X10DR
from a range of industrial headsets like the WPSHD heavy duty headset
that utilize the 5 pin mini-xlr connector. The WPSHC-NEX connects a WPSHD to a WPWLP-HIR wireless PTT adaptor.
The WPWLP-HIR** also allows use with 3M-Peltor™ hearing protection
devices and other headsets that use their 4 pole NEMA connector. It features a large PTT pad and a wireless PTT finger ring for ease of use in any
situation. **Contact your Distributor before ordering this item.
Earpiece port
3.5mm mono jack
WPEH
WPEB
WPTEP
XHC - Audio Access. Port
Hirose® 6 pin connector
WPiTRQ-X10 WPTEP-TL
WPEB-TL WPEH-TL
WPLWH-X10
+
WPSHD
WPSHD
WPSHC-HIR
+
WPSHC-NEX
+
WPWLP-HIR
ACCESSORIES
Interface Cables
XMC-* X10DR Interface cable, 1.5m (5’) length
XMC-XTL
version shown
XMC-* Series
XMC-3M
XDB-25T(15T)
XIB-CK
XFB
*Order with suffix as follows:
XMC-GEN generic interface cable - unterminated
XMC-C26 interface cable - Suits Cassidian TMR DB26HD
XMC-G25 interface cable - Suits GME P25 DB25
XMC-H26 interface cable - Suits Hytera MD6/78X DB26HD
XMC-HXG interface cable - Suits Harris HXG/M7300
XMC-i15 interface cable - Suits Icom DB15HD
XMC-i25 interface cable
- Suits Icom DB25
XMC-K15 interface cable - Suits Kenwood K19 cable (15pin)
XMC-K15D interface cable - Suits Kenwood NX720 DB15HD
XMC-K25 interface cable - Suits Kenwood NX700/TK7180/5710
XMC-K25A interface cable - Suits Kenwood DB25 TK690
XMC-XTL interface cable - Suits Motorola XTL/APX (pins-no connector)
XMC-XTL-M interface cable - Suits Motorola XTL/APX (includes connector)
XMC-M26 interface cable - Suits Motorola 26 pin(Trbo)
XMC-M26T interface cable - Suits Motorola 26 pin(TETRA)MTM5400
XMC-M16 interface cable
- Suits Motorola 16 pin
XMC-R15 interface cable - Suits Relm BK DB15
XMC-R25 interface cable
- Suits Relm BK DB25
XMC-SRG interface cable - Suits Sepura SRG3900
XMC-SRM interface cable - Suits Simoco SRM9000 DB15
XMC-T15 interface cable - Suits Tait TM70/80/9000 DB15
XMC-V15 interface cable
- Suits Vertex DB15
XMC-V25 interface cable - Suits Vertex DB25
XMC-CUS interface cable - Custom type/length - MOQ 200
(Contact your Distributor before ordering this item.)
XDB-15T adaptor cable
- DB15M to twin DB15F 20cm (8”) tail
XDB-25T adaptor cable
- DB25M to twin DB25F 20cm (8”) tail
XMC-3M extension cable - 3m (10’) interface extension cable
XIB XIB-TA XFB-TA XFB-MR XFB-LW XFB-DP XIB-CK
XIB
2/3 way interface box also order XIB-CK for each X10DR.
2/3 way interface box for talkaround/no emergency
Requires XIB-CK for each X10DR.
Talk Around & Emergency function box - 2 user only
Requires XIB-CK cable.
Dual radio function box
Requires XMC-* for each radio & one XIB-CK.
Lone Worker function box also order one XIB-CK cable.
Dual Press function box also order one XIB-CK cable.
X10DR to XIB/FB cable, 50cm (20”) length.
Vehicle Mounts
AMPS MOUNT
XMDM
XMDM is a multi-position mounting bracket which allows the X10DR to
be more easily mounted in today’s “space scarce” vehicles. The versatile
mount easily attaches to the mobile charger’s rear mounting plate.
The X10DR’s supplied rear mounting plate can be removed to reveal an
“AMPS” standard 4 post mounting facility. Any of the industry standard
mounting arms can then be utilized to mount the X10DR into the vehicle.
Desktop Chargers & Spares
X10DR
shown in
desktop
charger
XSMC-RK
XVMC-RK
XRMC-RK
XSMA
XRBC
XMCA
X10DRDC
X10DRSM- X 1 0 D R M D XU1/XX1
XU1/XX1
X10DRDC-*
XSMA XMCA X10DRSM-XU1
X10DRMD-XU1 X10DRSM-XX1
X10DRMD-XX1 XSMC-RF XVMC-RF XRMC-RF
XRBC
- Desktop charger includes AC/DC plug pack.
* specify AC plug style: US(2P), UK, EU(2P), AU (2P)
- Replacement secure microphone antenna.
- Replacement mobile charger antenna.
- Replacement basic secure mic.
* order with XHC option if Hirose connector required
- Replacement basic mobile charger.
- Replacement advanced secure mic.
- Replacement advanced mobile charger.
- Spring clip backcover retrofit kit.
- Velcro mount backcover retrofit kit.
- Removeable clip backcover retrofit kit.
- Spare removeable belt clip for XRMC.
SERVICE AIDS
creating a safer place to work
Test Box
Test speaker
XPK Programmer
XPS sensor
XIB-CK cable
X10DRDC desktop charger
XTIC test cable
requires:
The XSTB service test box allows the functionality of a
X10DR unit to be tested on a work bench.
The XSTB service kit includes:
- a control interface unit
- a test speaker
- a XIB-CK cable
- a XTIC test interface cable
- a XPS power sensor
- X10DRDC desktop charger
requires:
AC power cable
Not supplied
Control interface unit features:
A- LED that lights when any PTT is pressed.
B- LED that lights when emergency is pressed.
C- Toggle switch to activate remote PTT
D- Toggle switch to simulate radio COR operation.
E- Toggle switch to verify X10DR remote on/off operation
F- Toggle switch to activate an internal preset 1kHz tone
generator to check the X10DR’s Rx audio input.
AC power cable
Not supplied
The XPK programmer allows you to adjust a number
of parameters on both the X10DR secure mic and Xponder .
Parameters adustable include:
Talk permit tone, Emergency tone, PTT mute speaker,
Fixed alert tone volume, Internal mic volume, External
mic standard volume , External mic high volume, Remote monitor volume & Vox sensitivity.
The XPK programming kit includes:
- XPK programming software - USB cable
- USB-SPI interface adaptor
- Secure mic programming cable
- X-ponder programming cable with power supply
XTK Tracker
The XTK tracking software allows you to keep inventory and
maintenance records of X10DRs fitted with NFC tags. Fields
accessible include manufacture date, serial number, warranty,
and firmware details.
The XTK service kit includes:
- XTK tracking software and a USB NFC reader/writer
The tracking software allows you to enter last service date and battery replacement and also provides 6 free form
fields in which you can enter whatever details you wish, e.g. installation date, vehicle registration, personnel assigned to, purchase details, operating division, etc. All information is stored and can be exported as a csv file which
can be imported by MS excel, spreadsheets, etc.
SPECIFICATIONS
X10DR
®
Subject to change or improvement without notice
The equipment has been designed to meet the following global specifications:
Models:
Dimensions:
Weight:
Frequency:
Protocol: RF Power:
Battery Type:
Battery Life:
Encryption:
RF Connectors:
Rated Audio/Distortion: Operating Voltage:
Operating Temperature:
Shock & Vibration: Humidity/Rain/Dust:
Hirose Audio port:
Type Acceptance:
X10DR in desktop
charger
X10DR-XU1 Standard/ X10DR-XX1 Advanced
88 x 28 x 63mm (spk mic) 80 x 80 x 60 (chgr)
3.46 x 1.1 x 2.48” (spk mic) 3.15 x 3.15 x 2.36”(chgr)
149 grams (spk mic) 125 grams (chgr)
5.25 oz (spk mic) 4.4oz(chgr)
2.40-2.48GHz FH Spread Spectrum
802.15.4 based derivative
<100mW / X-Ponder <1W with XBDA
3.7V @1200mA Lithium Ion
>12 Hours @ 30% receive time/typical 24 hours plus
SAFER 64Bit std/128Bit Advanced model
RP SMA Female
>250mW @5% THD
3.7VDC
-20ºC to +50ºC /-4ºF to +122ºF
Mil Std 810 C/D/E/F
IEC529, IP55 (spk mic only)
Standard XX1 model/option XU1 model
FCC ID: I7OBT-24H / I7OBT-24D
IC:11443A-X10DRSM
CE, FCC, IC, Aust/NZ
0681
IC:11443A-X10DRMD
N13187
At Wireless Pacific we never lose sight that the right radio
communications solution is absolutely vital in securing
your organizational objectives. We constantly focus on
how to deliver a better solution. One that provides clean,
effective operational responsiveness with uncompromising
safety.
Works with:
ANALOG
TM
NXDN
TM
Copyright © 2014 Wireless Corporation Ltd. All rights reserved.
WIRELESS PACIFIC, X10DR, LIBERATE YOUR MOBILE RADIO, WHEN IT MATTERS
are trademarks or registered trademarks of Wireless Corporation. All other trademarks are the property of their respective owners.
Download PDF

advertising