™
ITP-5012L User Guide
03/2004
TABLE OF CONTENTS
ABOUT THIS BOOK
....................................................................................1
THINGS YOU SHOULD KNOW
ASSEMBLING YOUR KEYSET
................................................2–8
........................................................9
ITP-5012L SETUP ........................................................................................10
Initializing the ITP-5012L............................................................................................................10
IP Setup Menu ................................................................................................................................10
Menu Structure ..............................................................................................................................11
Navigating the Menus ................................................................................................................12
Setting the Network Parameters ............................................................................................12
OUTSIDE CALLS
Making an Outside Call ..............................................................................................................16
Dialing from the Outgoing / Incoming Menu ....................................................................17
Dialing the Most Recent Outgoing / Incoming Number ..............................................17
Making Calls from the Call Log ................................................................................................17
Answering a Call ..........................................................................................................................17
Universal Answer ..........................................................................................................................18
Recall Dial Tone ............................................................................................................................18
Sending a Flash..............................................................................................................................18
Busy Line Queuing with Callback ..........................................................................................18
Canceling Callback........................................................................................................................19
INTERCOM CALLS
Copyright 2004 Samsung Telecommunications America.
All rights reserved. No part of this manual may be reproduced in any form or by any means—graphic,
electronic or mechanical, including recording, taping, photocopying or information retrieval systems—
without express written permission of the publisher of this material.
Samsung Telecommunications America reserves the right without prior notice to revise information in
this guide for any reason. Samsung Telecommunications America also reserves the right without prior
notice to make changes in design or components of equipment as engineering and manufacturing
may warrant. Samsung Telecommunications America disclaims all liabilities for damages arising from
the erroneous interpretation or use of information presented in this guide.
Calling Other Stations ................................................................................................................20
Dialing the Most Recent Outgoing / Incoming Number................................................20
Answering Intercom Calls ..........................................................................................................20
Voice Announce Mode................................................................................................................20
Auto Answer Mode ......................................................................................................................21
Busy Station Callback ..................................................................................................................21
Busy Station Camp-On ................................................................................................................21
Calling your System Operator ..................................................................................................22
CALL PROCESSING
System Hold ....................................................................................................................................23
Exclusive Hold ................................................................................................................................23
Remote Hold ..................................................................................................................................23
Hold Recall ......................................................................................................................................24
Consultation Hold ........................................................................................................................24
Retrieving Calls Held at Another Station..............................................................................24
Transferring Calls ..........................................................................................................................25
Transfer with Camp-On ..............................................................................................................25
Transfer to Voice Mail ..................................................................................................................26
Call Waiting......................................................................................................................................26
Conference Calls ............................................................................................................................26
Conference Splitting ....................................................................................................................27
Forwarding Calls ....................................................................................................................27–28
Station Call Pickup ........................................................................................................................29
Group Call Pickup..........................................................................................................................29
My Group Pickup ..........................................................................................................................29
Privacy Release ..............................................................................................................................29
DIALING FEATURES
Speed Dialing ................................................................................................................................31
Programming Personal Speed Dial Numbers ....................................................................32
One Touch Speed Dialing ..........................................................................................................33
Directory Dialing ..........................................................................................................................33
Last Number Redial ......................................................................................................................34
Manual Retry with Redial ..........................................................................................................34
Save Number with Redial ..........................................................................................................34
Automatic Redial/Retry ..............................................................................................................34
Pulse to Tone Changeover ........................................................................................................35
Memo Redialing ............................................................................................................................35
PAGING AND MESSAGING
Making an Internal Page ............................................................................................................36
Making an External Page............................................................................................................36
All Page ............................................................................................................................................36
Meet Me Page ................................................................................................................................36
Call Park and Page ........................................................................................................................37
Messages—Set and Cancel ......................................................................................................38
Returning Messages ....................................................................................................................38
Programmed Messages ..............................................................................................................39
CONVENIENCE FEATURES
Do Not Disturb ..............................................................................................................................40
One Time DND ..............................................................................................................................40
Mute ..................................................................................................................................................40
Background Music ........................................................................................................................40
Established Call Pick-Up ............................................................................................................41
Appointment Reminder/Alarm Clock....................................................................................41
Door Phone Calls ....................................................................................................................43-44
Executive/Secretary Hotline......................................................................................................44
Group Listening ............................................................................................................................46
Account Codes ..............................................................................................................................46
Locking Your Keyset ....................................................................................................................46
Manual Signalling ........................................................................................................................47
Off-Hook Voice Announce ........................................................................................................47
OHVA Block......................................................................................................................................48
OHVA Reject ....................................................................................................................................48
In Group/Out of Group ..............................................................................................................48
CUSTOMIZING YOUR KEYSET
AME Password ................................................................................................................................49
Auto Camp-On ..............................................................................................................................49
Select Ring Tone ............................................................................................................................50
Change Your Passcode ................................................................................................................50
Set Answer Mode (Intercom)....................................................................................................51
Set Answer Mode (CO) ................................................................................................................51
Automatic Hold..............................................................................................................................51
Headset Operation ......................................................................................................................52
Hot Keypad......................................................................................................................................52
Key Confirmation Tone................................................................................................................53
Rejoining a Page............................................................................................................................53
Ring Preference..............................................................................................................................53
Auto Answer CO Calls..................................................................................................................54
Display Speed Dial Name ..........................................................................................................54
Caller ID Review All ......................................................................................................................55
Secure OHVA ..................................................................................................................................55
DISPLAY FEATURES
Directory Information ................................................................................................................ 56
Call Log ............................................................................................................................................56
Dial by Name ..................................................................................................................................57
Call Progress Displays ..................................................................................................................57
Display Number Dialed ..............................................................................................................58
Call Duration Timer ......................................................................................................................58
Auto Timer ......................................................................................................................................58
Timer Function ..............................................................................................................................58
Viewing Message Indications ..................................................................................................59
Personal Speed Dial Names ......................................................................................................59
Station Names................................................................................................................................59
Managing Key Assignments ....................................................................................................59
LCR with Clear ................................................................................................................................60
Backspace with LCR......................................................................................................................60
Text Messaging ......................................................................................................................60–61
CALLER ID
............................................................................................................62
Selecting your Caller ID Display ..............................................................................................62
Viewing the Next Caller ID Call................................................................................................62
Saving the Caller ID Number ....................................................................................................62
Redialing a Saved Caller ID Number......................................................................................63
Storing a Caller ID Number ......................................................................................................63
Inquire Caller ID Park/Hold Info ..............................................................................................63
Reviewing Past Caller ID Calls ..................................................................................................64
APPLICATION PROGRAM MENUS ........................................65
PhoneBook ......................................................................................................................................65
E-Diary ..............................................................................................................................................65
Message............................................................................................................................................66
Volume..............................................................................................................................................67
Call Forward ....................................................................................................................................68
Configuration ................................................................................................................................68
My Phone ........................................................................................................................................70
Status Screen of the LCD Panel................................................................................................71
SVMi-8/ SVMi-16E ......................................................................................72
SVMi-8/SVMi-16E Subscriber Services Menu Diagram .........................................73–74
Accessing your Mailbox ..............................................................................................................75
Getting Started .............................................................................................................................76
Listen to your Messages.............................................................................................................76
Subscriber Services Menu .........................................................................................................76
Listening to Old or New Messages ........................................................................................77
Group New or Old Messages....................................................................................................78
Record and Send a Message ....................................................................................................78
Access Manager ............................................................................................................................79
Personal Greetings ......................................................................................................................81
Mailbox Administration..............................................................................................................83
Message Broadcast ....................................................................................................................85
Personal Services ........................................................................................................................86
Personal Administration Settings ..........................................................................................87
Keyset User Features ..................................................................................................................88
Shortcuts ........................................................................................................................................90
Interactive Displays ......................................................................................................................90
ABOUT THIS BOOK
Samsung’s new OfficeServ technology keyset model ITP-5012L is part of the iDCS
500 Release 2.
The ITP-5012L IP keyset represents a new concept of Internet phone, in that it uses
an IP address to Send/Receive voice and data. For voice communications, the ITP5012L uses the data network line already in place in most offices and increasing
number of homes.
The ITP-5012L IP keysets also incorporate a large LCD screen, which provides
important information for the user, to make using the keyset easier and more convenient.
Please take the time to study this guide and to become familiar with the operation
of your keyset. Keep this guide handy, as you may need to look up instructions for
infrequently used features.
This book is written based on factory default settings, for the feature access codes.
Sometimes, due to programming requirements, these codes may be changed. If
you find that a feature code does not work as described in this book, please contact your installation and service company to determine the correct code.
PERSONAL SPEED DIAL NUMBERS ............................91–92
1
THINGS YOU SHOULD KNOW
USER ORIENTATION
The ITP model telephones are called “IP keysets”. The IP keyset incorporates buttons or “keys” that are used to access or activate the many features of your office
phone system. The lower five buttons (ten total) that reside on either side of the
Large Display screen are programmable buttons. This means they can be programmed for a specific function on your keyset and that same button can be
something different on another keyset. See the system manager to get your most
frequently used features assigned to your programmable buttons.
The top button on either side of the Large Display Screen scrolls through the various levels of the programmable button display screens.
TERMINAL STATUS INDICATOR
The terminal status indicator light is positioned on the top right corner of the keyset above the display. The terminal status indicator is a tri-colored (red, green, and
amber) light that provides greater visibility of your keysets status than the individual button LEDs. The terminal status indicator provides the following indications:
•
•
•
•
•
•
Busy/Off Hook
Intercom Ring
Outside Call Ring
Recall Ring
Message Waiting
Do Not Disturb
Steady Red
Flashing Red
Flashing Blue
Flashing Amber
Flashing Red
Fast Flash Red at 1 Second Intervals
SELECT BUTTONS
Lines from the telephone company are “C.O. lines”. Calls on these lines are referred
to as “outside calls”. Your system can have individual C.O. line buttons or lines may
be assigned to groups. When they are in a group, you access a line by dialing an
access code or pressing a route button. For example, dial 9 or press a “LOCAL” button to get a local outside line. If Least Cost Routing is used, pressing the “LCR” button will automatically select a preprogrammed C.O. line according to what digits
are dialed. Each line in the system is numbered, beginning with 701, then 702, 703,
etc.
The 5012L keysets incorporate twelve select buttons. These buttons are positioned six on either side of the LCD screen.
Direct Station Selection (DSS) buttons are programmed to ring specific stations.
You can press a DSS button instead of dialing the extension number.
The remaining five buttons on either side of the display are programmable. There
are ten programmable buttons per programmable feature screen, with the exception of the last screen, which has nine programmable buttons. The total programmable buttons per 5012L station is ninety-nine. Any system feature or function can
be assigned to these buttons.
The 5012L keyset provides distinctive ring patterns:
•
•
•
Outside calls have a single ring tone repeated.
Internal calls have a double ring tone repeated.
Door phone calls and alarm/appointment reminders have a triple ring tone
repeated.
SPEAKERPHONE
All ITP keysets are speakerphones. Pressing the SEND button will answer an
incoming call on the speakerphone. Pressing the END button will release the call
on the speakerphone.
Switching from the handset to the speakerphone is easy. Press the SPEAKER button and hang up the handset.
2
The top left and right buttons are used to access the various levels of the user
screens.The 5012L has ten levels of programmable feature screens. By pressing the
top left (DOWN arrow) you progressively increase the screen level number [1-10].
By pressing the top right (UP arrow) you progressively decrease the screen level
number [10-1].
VOLUME CONTROLS
The 5012L keysets use the UP and DOWN buttons to adjust the ringer volume
while the keyset is ringing, the speaker volume while the speakerphone is in use
and the handset volume while you are listening. These three levels will be stored
in memory until changed. If background music is turned on at your keyset, the volume buttons will also control the level of music. The volume of pages heard
through the speaker of a keyset can be adjusted during a page announcement by
using the volume buttons.There are 16 levels for each volume setting.The volume
of off-hook ring is controlled by a user-programmable setting.
3
SCREEN BUTTON
SCROLL BUTTON ASSEMBLY
The 5012L incorporates a SCREEN button. This button allows you to choose your
keyset’s idle screen display. The default is CALENDAR. The options are STATION
FIXED FEATURE buttons (two levels), or STATION PROGRAMMABLE buttons
(ten levels).
The scroll button is actually a type of thumbwheel assembly. You may use it to
scroll through the station screens. Rolling the SCROLL BUTTON DOWN (towards
the navigation button) will advance you through the multiple STATION FIXED
FEATURE and STATION PROGRAMMABLE button screens. Rolling the SCROLL
BUTTON UP (towards the station display) will bring the cursor back towards the
Main Screen. By scrolling up or down, you cause the cursor to move back and forth
through the screens in the same manner as the UP/DOWN arrows on the top
SELECT BUTTONS work.
NOTE:
From the default CALENDAR screen:
•
•
Press the SCREEN button once to access the STATION PROGRAMMABLE
BUTTON SCREEN #1. Press the DOWN arrow associated with the top left soft
key and you will advance to STATION PROGRAMMABLE SCREEN #2. Each
additional press of the DOWN arrow will advance you through the screens,
until you reach SCREEN #10. Press the UP arrow associated with the top left
soft key to return to the previous screen. Each additional press of the UP button will move you back towards the main screen.
Press the SCREEN button twice to access the STATION FIXED FEATURE
SCREEN #1. Press the DOWN arrow associated with the top left soft key and
you will advance to SCREEN #2.
NAVIGATION BUTTON
The 5012L keysets incorporate a Navigation Button. This button is designed to
assist the user in activating and using various station features, more easily. These
features include Outgoing Call Log, Incoming Call Log, Speed Number Search, Call
Forward Assign and Alarm Assign.
With the NAVIGATION BUTTON, the station user is no longer required to enter
station level programming to activate these frequently used features. A few button presses and these features are activated.
CONFERENCE BUTTON
The NAVIGATION BUTTON is divided into separate feature buttons. These buttons are described below.
The CONFERENCE button allows the user to set up a call with up to five parties
(station or trunk).
•
MENU BUTTON: This button displays the station feature main menu, which is
configured in icons, so that the users can easily utilize various settings and
helpful functions.
•
SEND BUTTON: If the station is programmed for Enblock Dial Mode, when
dialing an outside telephone number or internal station number, you must
press the SEND button to initiate the call. This button is also used when
reviewing recently received or called numbers and answering incoming calls.
TRANSFER BUTTON
TRANSFER is used to send any call to another extension in one of two ways. You
can do a screened transfer by informing the other extension who is calling or you
can do a blind transfer without notification.
HOLD BUTTON
When reviewing recently received calls, continue to press the SEND button for
more than 2 seconds and the last outside number called will be redialed.
The HOLD button maintains the call at your keyset, while enabling you to call
other stations or consult coworkers in confidence.
The SEND button operates as the ANS portion of the ANS/RLS button. An
ANS/RLS button may be assigned to the station as a programmable button.
SPEAKER BUTTON
•
The SPEAKER button allows you to have a conversation from the keyset without
lifting the handset.
ENTER BUTTON: This button is used to select a menu option, or to save
changes made to a menu or submenu option.
•
DIRECTION BUTTON: The DIRECTION BUTTON is the donut shaped ring,
which surrounds the ENTER button.This button is used to navigate within the
menus. There are directional arrows stenciled into this button, which indicate
which direction the cursor will be moved.
4
5
Note that the DIRECTION BUTTON has four icons, at the top, bottom, left and
right of the ENTER button. These icons are used to navigate directly to
particular programming options from the CALENDAR screen.
Pressing the top (HOME) icon will take you directly to the Main Menu. The
bottom (TONE) icon will take you to the Ring Tone/Volume Menu.The left side
(MESSAGE) icon will take you to the Text Message Menu. The right side
(PHONE) icon will take you to the PhoneBook Menu.
•
SYSTEM TONES
The system provides several tones to assist you. Some of these tones are already
familiar to you.
END BUTTON: This button is used to disconnect a call after a conversation or
to move to the initial screen.
The END button operates as the RLS portion of the ANS/RLS button. An
ANS/RLS button may be assigned to the station as a programmable button.
•
CANCEL BUTTON: This button is used to erase any characters or numbers
entered by the dial button or to move to the previous screen.
After pressing the MENU button, use the direction button to highlight the desired
menu icon. For multiple screen options, the UP/DOWN arrows at the either side of
the top of the LCD may be used to scroll on a per page basis. Press ENTER to
access that menu. To navigate within the menu, you may scroll to the desired
option/function, dial the associated option function number or press the associated select button on either side of the display.
Press the END button to exit programming.
FEATURE ACCESS CODES
This user guide is written based on the default access code for using system features. If the system numbering plan has been changed some of the access codes
may not be correct. Your installing company can inform you the correct codes.
6
7
ITP-5012L KEYSET
LCD Panel
Displays a large quantity
of information so that
the users can easily
search.
Volume Button
Used to adjust
the volume of
the handset,
speakerphone,
ringer, background music
and page.
Select Button (6)
ASSEMBLING YOUR KEYSET
•
Place the keyset face down on a flat surface.
Select Buttons (6)
To select a specific item
the user can simply
press the Select button
next to the item.
•
Insert notched ends of the support bracket into the channels located in the
upper section of the bottom panel. Push towards the top of the keyset to lock
in.
Status Indicator
Used to provide
your keyset status.
•
Plug the handset cord into the jack marked with the
•
Route the handset cord out the RIGHT side of the keyset as you look at it face
down.
•
Plug the eight-conductor LAN cable, from the wall, into the jack marked LAN
on the back of the keyset.
•
Plug the eight-conductor PC cable, from the PC, into the jack marked PC on
the back of the keyset.
•
Plug the power connector, from the power adapter provided, into the power
jack on the back of the keyset.
•
OPTIONAL: To connect a recording device, plug the device connector into the
jack marked REC on the bottom of the keyset.
Screen
Button
Scroll
Button
Navigation Button
Dial Button
Speaker Button
For handsfree operation and ringing.
Hold Button
Used to save a call
without hangingup on the current
call.
Microphone Button
Conference Button
Used to make a calls of
up to 5 parties.
Transfer Button
symbol.
IMPORTANT NOTE:
8
•
Be careful not to connect the Network LAN cable into the PC connector of the
phone.
•
To prevent damaging the keyset, only use the Power Adapter that came with
the 5012L keyset.
9
ITP-5012L SETUP
INITIALIZING THE ITP-5012L
•
•
•
Initially the ITP-5012L IP keyset will need to be setup to operate within the users
network.The Setup Menu is also used to make changes to the keyset, in the event
that the system information should change. The option chosen via scroll button
will be highlighted.
•
•
The [0]-[9] dial buttons are used to directly choose a menu, or sub menu
options.
The [ENTER] button in the navigation button assembly is used when saving a
modification.
The [MENU] button in the navigation button assembly is used to to display
the IP Setup Main Menu.
The [END] button in the navigation button assembly is used when canceling
or editing the modification, or existing programming.
The [CANCEL] button in the navigation button assembly is used to go back to
the previous screen or to delete the last digit of a displayed option value.
The station numbers will be automatically set by the iDCS 500 system once the
necessary information has been entered into the IP keyset. Enter ID and password
of the server, as described below to register the phone.
MENU STRUCTURE
See your system administrator for specific Network and Server addresses. The
addresses necessary to set up the ITP-5012L are:
1. INFORMATION
•
•
•
•
•
IP Address of Station
Network Gateway Address
iDCS 500 MCP2 Server Address
User ID
Password
IP SETUP MENU
Once the IP SETUP MENU is displayed, you can
move to each menu in the Set Up by using the
navigation buttons and [1]-[9] dial buttons of the
ITP-5012L IP phone.
•
•
10
1. Version
2. Network
3. Load Option
4. MAC Address
(Note that Option 3 will be indicated only when setting the Manual IP)
2. NETWORK
As soon as the ITP-5012L IP phone is connected to the power supply, press the
MENU button and the LCD displays the SETUP OPTIONS SCREEN.
To enter the IP SETUP MENU, press the MENU
button as soon as the ITP-5012L IP phone is connected to the power supply. Unplug the power
from the ITP. Press and hold the MENU button
while plugging in the power, then release the
MENU button.
The IP SETUP MENU is configured as follows:
1. Mode
2. IP
3. Netmask
4. Gateway
(Note that Option 2 will be indicated only when setting the Manual IP)
Setup (1/6)
1.Information
2.Network
3.Load & Upgrade
4.System
5.Server
6.Exit
The UP and DOWN directions buttons in the navigation button assembly are
used to move the highlighted bar up or down to the desired option.
The LEFT and RIGHT buttons in the navigation button assembly are used to
move the highlighted bar left or right, to the desired option, move to a sub
menu and if a menu is at the last line, that menu option will be executed.
3. LOAD & UPGRADE
1.
2.
3.
4.
Load Option
Upgrade Program
Upgrade Bootrom
Format
4. SYSTEM
1.
Password (Unused)
5. SERVER
1.
2.
3.
Server IP
ID
Password
6. EXIT
11
NAVIGATING THE MENUS
Setting IP Manually
When programming within various menu options, information can be entered via
the dial pad keys using [0]-[9] and [ ] dial keys, as well as utilizing the navigation
button assembly.
If [1. Manual IP] is selected the Network (1/4) sub
menu will be displayed.
The button used for editing and their features are summarized below.
BUTTON
The user directly enters the IP address, subnet
mask, and gateway, address as follows:
•
FEATURES
Left and Right ......................To move a cursor (highlighted area) or to erase what is
entered.
If the [2. IP] menu is selected, the LCD will display
the following message and the user can enter its
IP address.
Network (1/4)
1.Mode
2.IP
3.Netmask
4.Gateway
* Input IP Address
xxx.xxx.xxx.xxx
End............................................To cancel the current programming and return to the
Main Menu.
Check if there is any currently saved IP address of the phone on the LCD. If the IP
address has not been set, the LCD displays nothing. The user can enter the IP
address using [0]-[9] dial buttons and [ ] button can save that IP address by pressing the [Enter] button of navigation button assembly.
Cancel......................................To move back to the previous screen or delete the last
digit of the displayed option value.
•
Enter ........................................To save the current setting and end programming.
[ ] ............................................To enter [.] between IP address fields.
[0]-[9] ......................................To enter numerical values.
SETTING THE NETWORK PARAMETERS
Utilize the following programming steps to program the ITP-5012L IP keyset to
operate within the users network.
From the Setup, Main Menu, select [2. Network] to
set or modify the network parameters. The LCD
will display the Network (1/1) screen.
Network (1/1)
1.Mode
Press ENTER and you will see the Mode (1/2)
screen.
•
•
12
If [1. Manual IP] is selected, the user must
enter the IP address, subnet mask, and gateway value for the customer network that the
5012L resides on.
* Input Netmask
xxx.xxx.xxx.xxx
Check if there is any currently saved subnet mask address of the phone on the
LCD. If the subnet mask address has not been set, the display will show nothing.
Press any dial buttons from [0]-[9] and [ ] button to enter the subnet mask IP
address and then save that subnet mask IP address by pressing the [Enter] button
of navigation button assembly.
•
Network Parameter Setup
If the [3. Netmask] menu is selected, the user can
enter a new Netmask IP address.
If the [4. Gateway] menu is selected the user can
enter a new gateway address.
* Input Def. Gateway
xxx.xxx.xxx.xxx
The user can check if there is any gateway IP address of the phone that is currently saved on the LCD. If the gateway IP address has not been set, the LCD will show
nothing. Use any dial buttons from [0]-[9] and [ ] button to enter the gateway IP
address and save it by pressing the [Enter] button of navigation buttons.
NOTE: In the [2. Network Menu], [1. Mode] option, when [2. DHCP] is selected the
IP address, Netmask, and Gateway will not be displayed on the LCD.
Mode (1/2)
1.Manual IP
2.DHCP
If [2. DHCP] is selected, the IP address, subnet
mask, and gateway value will be set to the
default values automatically. (Choose this
option only if a DHCP server is available on the
local network).
13
Load and Upgrade Set/Modify
Authentication Server Related Set/Modify
The third item [3. Load & Upgrade] sets or modifies the IP phone’s software version. Use extreme caution when upgrading the keyset.
The fifth item [5. Server] sets or modifies settings related to the authentication
server. Select the [5. Server] item and move to the lower level. The screen below is
displayed.
Select the [3. Load & Upgrade] item and move to the lower level. The screen
below is displayed.
1.Server IP
1.Load Option
2.Upgrade Program
Item not visible in the first screen:
You can set/modify the IP address of the authentication server at the [1. Server IP]
item. The screen below is displayed when you enter the item. The server IP is the
IP address of the MCP2.
3.Upgrade Bootrom
Input ServerIP
4.Format
xxx.xxx.xxx.xxx
In the [1.Load Option] item, move to the lower level and select [2. File System].
Each of the items [2. Upgrade Program] and [3. Upgrade Bootrom] are used for
upgrading program and bootrom. Set the IP of the TFTP server you wish to
upgrade and press OK.
The [4. Format] item is used for deleting all programs and data except bootrom.
CAUTION: For engineering purposes only. The format option should not be used
unless instructed by an Authorized Samsung Engineering or Technical Support
Representative.
You can confirm the current IP address of the authentication server at the LCD
panel. The address is left blank if it is not set. Use the dial buttons from [0]-[9], and
[ ] to set the IP address and press the [ENTER] button among the navigation buttons to save and exit.
4 Input Id
xxxx
You must input the ID assigned to your ITP phone. See your phone system administrator to get this value. Press the [ENTER] button to save and exit.
4 Input Password
xxxx
You must input the password associated with your ID. See your phone system
administrator to get this value. Press the [ENTER] button to save and exit.
Completion of Settings
Verify settings at the first item [1. Information] after setting all of the above items.
Select the sixth item [6. Exit] to save all modified settings and reboot the ITP-5012L
phone.
14
15
OUTSIDE CALLS
Note: When making calls, internal or outside calls, in order to access the programmable button screens, press the SCREEN button. Then you can utilize either the
SCROLL button or the UP/DOWN arrow (select) buttons on the display.
DIALING FROM THE OUTGOING /
INCOMING MENU
•
•
•
MAKING AN OUTSIDE CALL
IMPORTANT: Put phone in OVERLAP MODE:
•
•
•
Press the MENU button.
Select CONFIG and then select DIAL MODE.
Change it to OVERLAP. If your phone is not in OVERLAP mode you must
always press the SEND button after dialing the digits to send the call.
•
Lift the handset and press an idle outside line button, line group button or dial
a line access code to receive dial tone—OR—press an idle outside line button,
line group button or dial a line access code to receive dial tone through the
speaker—OR—lift the handset and dial the Trunk Group access code or simply start dialing.
Dial the telephone number or the Intercom number.
Finish the call by replacing the handset. To disconnect a speakerphone call,
press the ANS/RLS or END button.
•
•
NOTES:
1. You will receive No More Calls tone when you attempt to make a call and
there is no button available for that line.
2. If Least Cost Routing is enabled on your phone system, this button may
be labeled LCR or accessed by dialing an access code (usually 9).
3. If your system is programmed to require an authorization code before
making a call, dial plus a valid code before selecting a C.O. line.
4. If your system is programmed to require an account code before making
a call, press the ACCT button or dial 47 plus a valid bin number, press the
ACCT button again and then select a C.O. line.
•
From the station idle screen, press the MENU button and select P-BOOK.
Select DIALED Nos or RECEIVED Nos from the submenu. These menus will
store the last thirty calls made to and from the station.
Press the select button on the display, associated with the number to redial or
use the DIRECTION or SCROLL button to move the cursor to the desired
number. Press the ENTER button to display the detailed information of the
number.
Press the SEND button to dial the number.
DIALING THE MOST RECENT OUTGOING /
INCOMING NUMBER
•
•
Press the SEND button. The most recent call (Internal or External) to or from
the station will be displayed.
Continue to press the SEND button and the system will automatically dial the
number for you.
MAKING CALLS FROM THE CALL LOG
The Station Call Log displays the last outgoing station, and incoming trunk calls.
The total number of calls that can be displayed is 60. You may redial any of these
calls from the Call Log.
•
•
•
•
Press the SEND button to display the first page of the CALL LOG.
Use the SCROLL button or the DIRECTION button to navigate to the desired
number. Use the UP and DOWN arrows, associated with the top left and right
soft keys to advance and return through the CALL LOG Screens.
When the desired number is highlighted, press the SEND button.
The number will be automatically dialed.
ANSWERING A CALL
For more information on authorization and account codes, see your system
administrator.
•
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
•
Lift the handset and you are automatically connected to the ringing call. See
Ring Preference under Customizing Your Keyset—OR—press the SEND button
to automatically answer on the speakerphone.
While a call is ringing in, the display will indicate the type of call coming in
(station number and name, trunk number and name, etc.)
NOTES:
1. If a call is flashing at your keyset but not ringing, you must press the flashing
button to answer.
16
17
2.
While a call is ringing in, press the SCREEN button to display the programmable button screen. This will enable you to view and invoke any of the station
features that you may wish.
UNIVERSAL ANSWER
Outside lines may be programmed to ring a general alerting device. To answer
calls ringing this device, dial 67—OR—press the UA button. This device can operate in any one of the six different ring plans.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
RECALL DIAL TONE
•
CANCELING CALLBACK
A callback will be canceled if not answered within 30 seconds. If you have set a
callback, the cursor associated with the CALLBACK button, will be solid black.
To cancel a callback:
•
•
Press the CALLBACK button, if programmed, or dial 44. The display will show
the callback details and an option to CLEAR the callback.
Press the CLEAR button, or press the HOLD button.This will cancel the last set
callback and display the next set callback, also with the option to CLEAR.This
process is repeated until all callbacks are cleared from memory.
NOTE: If the Hot Keypad feature is turned off, you must first lift the handset or
press the SPEAKER button before dialing.
Press the NEW button to disconnect your existing call, wait for dial tone and
then make a new call on the same line.
NOTE: If this button does not appear on your keyset, the FLASH button may be
programmed to recall dial tone.
SENDING A FLASH
While on an outside call, press the FLASH button to send a flash to the telephone
company. This is required for some custom calling features or CENTREX use.
NOTE: Flash is not available on an ISDN circuit.
BUSY LINE QUEUING WITH CALLBACK
If you receive a busy signal when you are selecting an outside line, this means that
the line or group of lines is busy.
•
•
•
•
Press the CALLBACK button, if programmed, or dial 44, you will hear confirmation tone.
Press the ANS/RLS or END button.
When the line becomes free, the system will call you back.
Lift the handset or press the SEND button to answer, wait for dial tone and dial
the telephone number or speed dial number again.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set
a callback, the cursor associated with the CALLBACK button will be solid
black.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
18
19
INTERCOM CALLS
CALLING OTHER STATIONS
•
•
•
Dial the extension number or group number.
Wait for the party to answer. If you hear a brief tone burst instead of ringback
tone, the station you called is set for Voice Announce or Auto Answer. Begin
speaking immediately after the tone.
Finish the call by replacing the handset or pressing the ANS/RLS button or
END button.
NOTES:
1. If you have a DSS button assigned to an extension or station group, you may
press this button instead of dialing the number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
DIALING THE MOST RECENT OUTGOING /
INCOMING NUMBER
•
•
Press the SEND button.The most recent call (Internal or External to system) to
or from the station will be displayed.
Continue to press the SEND button and the system will automatically dial the
number for you.
AUTO ANSWER MODE
When another station calls you, your keyset will sound a brief attention tone and
then automatically answer the call.
•
•
Your microphone and speaker are turned on and you can speak handsfree.
For privacy, use the handset.
To finish the call, replace the handset or press the ANS/RLS or END button.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
to ON.
BUSY STATION CALLBACK
When you call another station and receive a busy signal:
•
•
•
Press the CALLBACK button, if programmed, or dial 44.
When the busy station becomes free, your keyset will ring.
Lift the handset or press the ANS/RLS or SEND button to call the now idle
station.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set
a callback, the cursor associated with the CALLBACK button, will be solid
black.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER or SEND button before dialing.
ANSWERING INTERCOM CALLS
BUSY STATION CAMP-ON
•
When you call another station and receive a busy signal but you do not want to
wait for a callback:
•
When your keyset rings, simply lift the handset—OR—press the ANS/RLS or
SEND button to be connected to the calling station.
Finished the call by replacing the handset or pressing the ANS/RLS or END
button.
See Ringing Preference under Customizing Your Keyset.
MANUAL CAMP-ON
•
•
VOICE ANNOUNCE MODE
When another station calls you, your keyset will sound a brief attention tone and
you will hear the caller’s announcement.
•
•
Press the ANS/RLS or SEND button to turn on the microphone and speak
handsfree—OR—lift the handset to reply.
To finish the call, replace the handset or press the ANS/RLS or END button.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
to ON.
20
•
•
Press the CAMP button or dial 45.
The called station will receive off-hook ring tone repeated every few seconds
and the cursor associated with the first available CALL button will flash black
to indicate your call is waiting.
Wait for the called party to answer.
The called station must release its first call or place it on hold before answering your camp-on.
NOTES:
1. If you receive No More Calls tone, that station has no available button to
accept your call. Hang up or leave a message.
21
2.
If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing.
CALL PROCESSING
AUTO CAMP-ON
When you want to automatically camp on to a busy station without pressing the
camp on button every time you call a busy station, you can set your phone for auto
camp-on.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 081 to turn ON auto camp-on or 080 to turn it OFF.
Press TRANSFER to store your selection.
SYSTEM HOLD
When you are connected to any call, press HOLD.The call will flash at the keyset. If
this call appears on a line button at other keysets, it will flash at those keysets also.
•
To take the caller off hold, press that button and the flashing LED will go
steady again. Resume the conversation—OR—press the HOLD button. The
flashing LED will go steady again and you will be connected to the call again.
Resume the conversation.
From the LCD:
•
•
•
•
•
Press the MENU button.
Scroll to CONFIG option and press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to AUTO CAMPON option. Press ENTER to change status.
Press CANCEL to return to main configuration screen—OR—press END to
return to idle screen.
CALLING YOUR SYSTEM OPERATOR
•
•
Dial 0 and press SEND button to call your system operator or group of operators.
If you want to call a specific operator, dial that person’s extension number.
NOTE: If the Hot keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
NOTE: While on a call, pressing a line button, route button or flashing CALL button
will automatically put your first call on hold and connect you to the new call. See
Automatic Hold under Customizing Your Keyset.
EXCLUSIVE HOLD
To place an outside call on hold at your phone so that other users cannot get it:
•
•
Press the HOLD button twice. The call will flash on your keyset and this line
will show a steady indication on other keysets.
To retrieve the call, press the flashing line button or press the HOLD button a
third time.
NOTE: Intercom calls will always be placed on exclusive hold.
REMOTE HOLD
When you wish to place a call on hold at another station.
•
•
Press TRANSFER and dial the station number (or press the appropriate DSS
button)
Press the HOLD button. This will place the call on system hold on an available
CALL button or Line button at the remote station and return you to dial tone.
NOTES:
1. If the destination station does not have any free CALL buttons or line buttons
you will hear No More Calls tone and must return to the other party by pressing the TRANSFER button (or the RETURN soft key in the display).
2. Intercom calls cannot be put on remote hold.
22
23
HOLD RECALL
TRANSFERRING CALLS
If you leave a call on hold longer than the hold timer, it will recall your station. The
button that the call appears on will have a slow flashing indicator.
•
•
When your phone rings, lift the handset or press the ANS/RLS button—OR—
press the SEND button to answer the recall.
If you do not answer this recall within a pre-programmed period of time, it will
go to the system operator.
Transfer is used to send any calls to another extension in one of two ways.You can
do a screened transfer by informing the other extension who is calling or you can
do a blind transfer without notification.
•
CONSULTATION HOLD
When you are talking on an outside line and it is necessary to consult with another extension:
•
•
•
•
Press the TRANSFER button; you will receive transfer dial tone. Your call is
placed on transfer hold.
Dial the extension number.
Consult with the internal party.
Press TRANSFER to return to the outside party or hang up to transfer the call.
NOTE: Repeatedly pressing the TRANSFER button will toggle between the outside
party and internal extension. If necessary you may disconnect either one of the
parties by pressing the DROP button.
RETRIEVING CALLS HELD AT ANOTHER
STATION
When a line is on hold and it appears on your keyset, press the LINE button with
the flashing indicator.
When a line is on hold and it does not appear on your keyset, dial 12 plus the line
number or the extension number of the station that placed the call on hold.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
•
•
•
While on a call, press the TRANSFER button and dial an extension number or
group number. Your call is automatically put on transfer hold—OR—press a
DSS button or station group button. Your call is automatically put on transfer
hold.
Hang up when you hear ringing (this is an unscreened or blind transfer)—
OR—wait for the called party to answer and advise him/her of the call and
hang up. If the transfer is refused, you will be reconnected to the outside line
when the called station hangs up or you can press TRANSFER to return to the
outside party.
If you wish to send the call to another extension without waiting for the first
station to hang up, simply press another DSS button—OR—press the CALL
button or C.O. line button to return to the outside party and begin the transfer process again.
When you are transferring a call to a keyset set for Voice Announce or Auto
Answer, the transferred call will always ring.
NOTES:
1. After the inside party answers, you may alternate back and forth between the
parties by pressing the TRANSFER button.
2. If you receive No More Calls tone, that station has no button available to receive another call. Press TRANSFER to return to the other party.
3. You cannot transfer an Intercom call by pressing a DSS button.You must press
the TRANSFER button and dial the destination extension number.
TRANSFER WITH CAMP-ON
When you are transferring a call to another station and you receive a busy signal,
you may camp the call on to this station. Simply hang up when you hear the busy
signal. The called party will be alerted that a call is waiting for them.
NOTE: If you receive No More Calls tone, that station has no button available to
receive another call. Press TRANSFER to return to the outside caller.
24
25
TRANSFER TO VOICE MAIL
This feature is used to send a call directly to a voice mailbox.Your keyset must have
a correctly programmed VT button to accomplish this. To transfer a call directly to
a voice mailbox:
•
•
While on a call, press the VT button and dial the mailbox number.
Hang up when dialing is completed.
CALL WAITING
If an outside call has been camped-on to your phone or another station has
camped-on to you:
•
•
•
Your keyset will ring and the call that is waiting for you (camped-on) will flash.
Press the flashing button to answer; your other call will go on hold automatically if your station has the Automatic Hold feature set. If not, you must press
HOLD and then the flashing button—OR—finish the first call and hang up;
the waiting call will ring.
Lift the handset or press the ANS/RLS or SEND button to answer.
ed together in a trunk to trunk conference, press the CONFERENCE button plus
the CALL button that the call appears on or follow the instructions to drop a party
and use your extension number. When they hang up, the lines will release automatically. Press CONFERENCE to rejoin a trunk to trunk conference.
CONFERENCE SPLITTING
If you are the controlling party of a conference and your keyset has the Auto Hold
feature turned on (See Customizing Your Keyset) and all of the outside lines involved
in the conference appear as buttons on your keyset, you can split the conference
into separate calls as follows:
•
Press any one of the outside line buttons. That outside line indicator will
remain steady to indicate you are still connected to it. All other outside lines
in the conference will be placed on system hold at your keyset. All intercom
callers in the conference will be disconnected. You may now speak with each
caller privately and transfer them as usual, or reestablish another conference.
FORWARDING CALLS
NOTE: Intercom calls will not go on Automatic Hold.
This option allows for one button Call Forward setting.You may forward your calls
to another station, station group or external destination.
CONFERENCE CALLS
Call forwarding may be set in several different manners:
You may conference up to five parties (you and four others) in any combination of
outside lines and internal stations in any order.
1.
•
•
•
•
While engaged in a conversation, press the CONFERENCE button and receive
conference tone.
Make another call, either intercom or outside, press the CONFERENCE button
and receive conference tone.
Make another call or press the CONFERENCE button to join all parties.
Repeat the last step until all parties are added.
NOTE: When attempting to add another party to the conference and you are not
able to reach the desired person, hang up. Simply press the CONFERENCE button
again to return to your previous conversation.
From the dial pad, dial 60 plus the extender (see below) that corresponds with
the type of forwarding desired, followed by the station number to forward to.
60 + 0 Call Forward Cancel. Cancels all call forwarding from the station.
60 + 1 Call Forward All Calls. Forwards all calls under any condition.
60 + 2 Call Forward Busy. Forward calls to another station when you are on
the phone.
60 + 3 Call Forward No Answer. Forward calls to another station when you
don’t answer.
60 + 4 Call Forward Busy/No Answer. Sets both Forward Busy and Forward
No Answer.
60 + 5 Call Forward DND. Forwards calls when you activate DND.
To drop a party from your conference call:
•
•
Press CONFERENCE and dial the extension or line number that is to be
dropped.
Press CONFERENCE again to reestablish the conference.
60 + 6 Call Forward Follow Me. Forward calls to the station where you currently are.
NOTE: To leave the conference, hang up. Control is passed to the next internal station. If there are no internal stations and you wish to leave outside lines connect26
27
2.
From the LCD:
STATION CALL PICKUP
•
•
•
Press the MENU button, scroll to the FORWARD icon, press ENTER.
Scroll to the desired Forward Option. Press MENU button.
Select MODIFY, enter the Station Number to forward to and press ENTER.
To pick up (answer) a call ringing at another station, lift the handset and dial 65
plus the extension number of the ringing phone.
NOTE: Once call forwarding has been initially set, for subsequent settings, you may
scroll to the desired forward type and press ENTER to forward to that same destination.You may also press the SELECT button associated with the desired forward
type, as opposed to scrolling to it.
If you have a DP key assigned with a station number, you only need to press this
DP key with the flashing light to answer this ringing station.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER button before you begin dialing.
3.
From the Station Feature Button:
GROUP CALL PICKUP
•
Each of the forward types may be assigned its own feature button. Pressing
the desired feature button will set forwarding to the last destination.
To pick up (answer) a call ringing in any pickup group, lift the handset and dial 66
plus the desired group number 01–20 or press the flashing GROUP PICKUP button if available.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. The station that receives a Forward All call can transfer the call to the forwarded station. This is useful when you are expecting an important call but
you do not wish to be disturbed by other calls.
3. When a station user places his/her keyset in Forward All mode and he/she
does not have a FORWARD ALL button, the TRANSFER button will light to
indicate Forward All has been set and calls to this station have been transferred elsewhere.
CALL FORWARD OPTIONS
A display keyset may review or change call forward options and destinations. Call
forward access can be done via the keypad or by accessing the keyset display features. To review or change call forward options:
•
•
•
•
•
28
Press TRANSFER 102.
Dial 0-6 to select the forward type (e.g., 1) OR
Press UP or DOWN to select the forward type
Press the right soft key to move the cursor
Dial the destination number (e.g., 202) OR
Press UP or DOWN to select the destination
Press the right soft key to move the cursor
Dial 1 to set OR
Press UP or DOWN to select YES or NO
Press TRANSFER to store and exit
NOTES:
1. A group pickup button can have an extender for a specific pickup group.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before dialing the access code.
MY GROUP PICKUP
If desired, a new access code can be assigned to pickup ringing calls in the same
pickup group as you are in. Like “66” above except you do not need to dial the
desired group number. See your installation company for the assigned access
code. MY GROUP PICKUP: __________________.
PRIVACY RELEASE
This feature will allow another station to join in our conversation by releasing privacy on the C.O. from your phone.
To Release Privacy:
While you are talking on a C.O. line and you wish to have other internal parties (or
up to three) join the conversation.
•
Press the PRB button (the PRB indicator will be steady). Inform the other
party that he/she may now join the conversation.
After the other party (or parties) has joined the conversation and you wish to
return privacy to the line so that no one else can join the conversation, press the
PRB button a second time, the PRB button LED will be off.
29
To Join a Non-Private Conversation:
DIALING FEATURES
When someone has informed you that you can join a conversation:
•
•
Press the C.O. line button that he/she has indicated.
OR
Dial the C.O. line number that he/she has indicated.
SPEED DIALING
You can dial a preprogrammed telephone number stored in the system-wide
speed dial list of numbers 500–999 or from your personal list of numbers 00–49.
Your system may be set for 950 system wide numbers. If so the system speed dial
access codes are 050~999 and the station speed dial codes are 000~049.
•
•
•
From the Main Fixed Feature screen with the handset on-hook, press the
SPEED DIAL button or dial 16.
Dial the desired speed dial number.
The telephone number is automatically dialed for you.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
From the LCD:
•
•
•
•
Press the MENU button.
Scroll to the PHONEBOOK option, press ENTER.
Scroll to SEARCH, press ENTER.
Choose the method to be used to initiate a speed call, as described below.
SEARCH—Search and initiate speed dial calls by: Speed Dial Number, Associated
Names, Telephone Numbers, Assigned Groups or Previous Calls, registered to the
phone.
•
Scroll to, or dial the associated number of the desired function. (Search,
Outgoing, Incoming, New Number, Edit Group, Delete All, My Own Number)
and press ENTER.
•
Once in the menu, you may dial the selected number, change, delete or register the number. When the information is displayed, press ENTER to dial the
number, press MENU to display further options.
1. BY SPEED DIAL #: Searches all speed dial numbers assigned to the phone.
Enter the speed dial number of the party you wish to call. When the number
is displayed, press ENTER and the number will be automatically dialed for you.
If you press ENTER without entering a speed dial number, all registered numbers will be displayed.
2. BY NAME: Searches for a telephone number by names associated with them.
Enter the name in the “By Name” box and press ENTER. When the name is displayed, press ENTER again and all of the numbers associated with that name
30
31
are displayed. Using the direction button, highlight the desired number. Press
ENTER and the system will automatically dial it for you.
If you press ENTER without entering a name, all registered names will be displayed.
3. BY PHONE NUMBER: Searches for an entry by the phone number registered.
Enter the phone number of the party you wish to call. Press ENTER and the
number will be displayed from the PHONEBOOK. When the number is displayed, press ENTER and all information associated with that number is displayed.
•
Press MENU button.
Scroll to PHONEBOOK option, press ENTER.
Scroll to New Number and press ENTER. Or you may dial [4] and immediately enter the option.
Enter the name and all desired phone numbers for that particular speed dial
entry and press ENTER.
ONE TOUCH SPEED DIALING
You may assign any speed dial number to an already existing One Touch Speed
Dial button for quick and easy dialing of frequently used numbers.
Notes:
•
•
•
4. BY GROUP: Searches for an entries by group information registered. Scroll to
group or enter associated number, press ENTER. The numbers registered to
that group are displayed. Scroll to the desired number and press SEND. The
number is automatically dialed for you.
5. BY TIME: Searches for entries based on incoming calls that have registered
numbers on the set. Scroll to the desired entry and press ENTER. The information associated with that call will be displayed. Scroll to the desired number entry and press SEND to have the number dialed automatically for you.
PROGRAMMING PERSONAL SPEED
DIAL NUMBERS
You can program frequently dialed telephone numbers in a personal speed dial
list. A station may be assigned up to fifty numbers, 00–49. See your system administrator to determine the amount assigned to your station. The phone itself maintains 1000 station speed dial numbers.
•
•
•
•
If you press ENTER without entering a number, all registered numbers will be
displayed.
—Entering (*123*) searches all numbers that include the 123 in them.
—Entering 305* searches all numbers that begin with 305.
—Entering *3000 searches all numbers that end with 3000.
•
•
•
•
From the LCD:
While on-hook, press TRANSFER and then dial 105.
Dial a speed dial number (00–49).
Dial a line or line group access code.
Dial the telephone number to be stored (24 digits maximum). It can include
#, , FLASH and PAUSE.
Press TRANSFER to store the number.
•
While on-hook, press TRANSFER and then dial 107.
Press a One Touch Speed Dial button.
Dial the speed dial number (00–49 or 500–999) that you want assigned to
this button.
Press TRANSFER to store your selection.
To call this telephone number, just press the One Touch Speed Dial button.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
DIRECTORY DIALING
•
•
•
Press the SCREEN button twice. Scroll to the first Fixed Feature screen.
Press the DIRECTORY button.
Press the soft button associated with the desired option.
STN - Accesses Station name directory,
SYSTEM - Accesses System speed dial name list.
PERS - Accesses your personal speed dial name list.
•
•
•
Enter the first digit of the desired party.
Press the UP/DOWN buttons to scroll to the desired entry.
Press the appropriate operation soft button:
DIAL - Dials the displayed number.
PREVIOUS - Moves you to the previous entry.
EXIT - Exit programming and return to idle screen.
NEXT - Moves you to the next entry.
•
Press END to return to idle screen.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER key before you begin dialing.
32
33
LAST NUMBER REDIAL
To redial the last telephone number you dialed, press the REDIAL button or dial
19.
To redial the last telephone number you dialed, from the Main Fixed screen, press
the LAST REDIAL button.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. Redial does not apply to intercom calls.
MANUAL RETRY WITH REDIAL
While you are on an outside call listening to a busy signal and you want to redial
the same number dialed.
•
Press the REDIAL button.
This will hang up your existing call and manually redial the same number dialed.
You can repeat this operation for a limited number of attempts.
SAVE NUMBER WITH REDIAL
•
When the called party answers, lift the handset or press the flashing SPEAKER to begin speaking.
NOTES:
1. If you make another call, auto-redial is canceled.
2. To cancel an auto-retry, lift and replace the handset.
PULSE TO TONE CHANGEOVER
When making an outside call on a dial pulse line, press #. All digits dialed after the
# with be sent as tones.
MEMO REDIALING
When you are calling directory information, you can store the number you are
given using the SAVE feature. There is no need for pencil and paper.
•
•
•
While you are talking on an outside call, press SAVE.
Dial the telephone number as it is dictated to you on the key pad.
Press SAVE to store the number.
To dial the number, press the SAVE/REPEAT button. It will select the same line and
dial the stored number. If necessary, you can select a different line and then press
the SAVE/REPEAT button.
To save the number you just dialed for later use, press the SAVE/REPEAT button
before hanging up.
To redial this saved number at any time, press the SAVE/REPEAT button or dial 17.
The same line will be selected for you.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
2. The saved telephone number is stored in memory until you save another
number.
3. Redial does not apply to intercom calls.
AUTOMATIC REDIAL/RETRY
When you are making an outside call and you receive a busy signal, the system can
automatically redial the number for you. It will automatically redial at a pre-programmed interval for up to 15 attempts.
•
•
34
When you hear a busy signal, press the AUTO-RETRY button.
The system will reserve the line and automatically redial the same number for
you. You will hear the call being made through the keyset speaker. The microphone is muted.
35
PAGING AND MESSAGING
•
•
•
Press WAIT or TRANSFER.
Remain off-hook until the person dials 56 from any phone.
The paged person will be automatically connected with you.
MAKING AN INTERNAL PAGE
CALL PARK AND PAGE
To make an announcement through the keyset speakers:
When you have an outside call for someone who is not at his/her desk, you can
park the call prior to paging. The iDCS 500 offers two different methods:
•
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial the desired zone number 0, 1, 2, 3 or 4.
After the attention tone, make your announcement.
NOTE: If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
MAKING AN EXTERNAL PAGE
MANUAL PARK ORBITS
•
•
•
•
•
To make an announcement through the external paging speakers:
•
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial the desired zone number 5, 6, 7 or 8—OR—dial 9 to page all external
zones.
After the attention tone, make your announcement.
NOTE: If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
ALL PAGE
To page all designated keysets and external speakers at the same time:
•
•
•
•
Lift the handset.
Press the PAGE button or dial 55.
Dial or press the ALL PAGE button.
After the attention tone, make your announcement.
NOTE: The indicator on the PAGE button will be lit steady when an All Page is in
progress.
While in conversation, press the PARK button.
Entered a desired orbit number (0-9), if the orbit number is busy dial another
orbit number. Display users can press to automatically place the call in any
available orbit number and see the number in the display.
Remember the selected orbit number.
Replace the handset when finished.
Lift the handset and make a page announcement as previously described
(example:“John Smith park two”).
To retrieve a parked call from orbit:
•
•
Press the PARK button and dial the announced orbit number (0-9).
You will be connected to the parked call.
NOTES:
1. You must have a PARK button or park access code to retrieve and place calls
in park orbits.
2. If the parked call is not retrieved within a pre-programmed period of time, it
will recall your keyset and have a slow flashing amber light. You cannot park
and page intercom calls.
3. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
AUTOMATIC PARK WITH PAGE BUTTON
•
•
•
While in conversation, press the PAGE button.The call is automatically parked
at your station.
Receive page tone and dial a desired page zone number.
Make announcement indicating your extension number or the line number.
Hang up.
MEET ME PAGE
To retrieve an automatically parked call:
•
•
•
•
•
Dial 10 plus the number that was announced. If you have a PAGPK button,
press it and dial the number that was announced. If you have a PARK button,
press it and dial the announced orbit number.
•
You will be connected to the parked call.
36
Lift the handset.
Press the Meet Me Page (MMPG) button or dial 54.
Dial the desired zone number.
After the attention tone, instruct the paged person to dial 56.
37
NOTES:
1. If the call is not retrieved within a pre-programmed period of time, it will recall
your keyset and have a slow flashing amber light. You cannot park and page
intercom calls.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
SETTING A MESSAGE INDICATION
When you are calling another station and no one answers or you receive a busy
signal, you can leave a message indication:
•
•
Press the MESSAGE button—OR—dial 43 and receive confirmation tone.
Hang up.
The message button on the Main Programmable Button screen and the TSI
will flash at the called station.
NOTES:
1. A station can have up to five message indications.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
CANCELING MESSAGES
To cancel a message indication that you left at another station, dial 42 plus the
extension number of the station at which you left a message.
3.
PROGRAMMED MESSAGES
When you will be away from your phone for any length of time, you can leave a
programmed station message. Display stations calling you will see this message
and be informed of your status or follow your instructions.
•
•
•
You can have multiple programmed message buttons (PMSG) and each one can
have a different message code:
•
•
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
•
•
•
•
•
•
Press the MESSAGE button or dial 43. The first station that left a message will
be called automatically. If that station does not answer, your MESSAGE button
indicator will continue to flash and the TSI will stay on.
Repeat until all messages have been returned in the order received.
Your MESSAGE button indicator will stop flashing and the TSI will turn off
when all messages have been returned.
Press any programmed message (PMSG) button. The message is set and the
PGM MSG button indicator will be lit steady. Press the button again to turn off
the programmed message and the indicator will go blank.
Pressing another programmed message (PMSG) button will turn the previous
one off and set a different programmed message.
To assign absent messages via the LCD:
•
•
Dial 48 plus any of the message codes (01–20) listed on the back of this user
guide.
To cancel any of these messages you might have selected, dial 48 plus 00.
Press TRANSFER to exit and store your selection.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button.
To cancel all message indications left at your keyset, dial 42 plus your extension.
Your MESSAGE button indicator will stop flashing and the TSI will go out.
RETURNING MESSAGES
If a message has been left at your keyset by a keyset in Auto Answer, you must
manually cancel the message after it has been returned.
Select pre-programmed, or custom messages from the extended absences
(10 pre-programmed and 10 custom messages).
Scroll to or dial [7] and press ENTER.
Scroll UP/DOWN to the desired message.
Press ENTER, display confirms save.
To clear absent message, press MENU at message option and scroll down to
clear, press ENTER, display requires more input, select YES/NO, press ENTER,
display confirms cleared.
NOTES:
1. Display keyset users can view message indications and return them in any
order. See Viewing Message Indications under Display Features.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin dialing.
38
39
CONVENIENCE FEATURES
DO NOT DISTURB
ESTABLISHED CALL PICKUP
To pick up an established call in progress at a single line extension connected to
a computer modem on your PC.
•
Use this feature when you want to block calls to your keyset.
•
•
While on-hook, press the DND button or dial 401. The DND button indicator
will be lit steady to remind you of this mode.
To cancel DND, press the DND button again or dial 400.The DND button indicator goes blank. You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button.
2. If you place your keyset in DND mode and you do not have a DND button,
your TSI button will flash to indicate DND status.
ONE TIME DND
If you are on a call and you do not wish to be interrupted while on that call, you
can press the DND button and place your station in Do Not Disturb. When you
hang up at the end of the call, DND will be automatically canceled and your keyset will be able to receive new calls. This feature requires a DND button.
MUTE
You can mute the handset transmitter or the microphone during any conversation:
•
•
Press the MUTE button. The MUTE button indicator will be lit steady.
To resume speaking, press the MUTE button again. The MUTE button indicator goes blank.
BACKGROUND MUSIC
When a music source is supplied, you may listen to music through the speaker in
your keyset:
•
•
While on-hook, press the HOLD button to hear music.
Press the HOLD button again to turn music off.
You can set the level of background music by using the VOLUME buttons while listening to the music. This does not affect the speakerphone level.
40
•
Press the EP button for that station on your keyset and the call is automatically moved to your keyset.
The single line extension on your modem will be disconnected.
NOTE: You must have an assigned (EP button) button on your regular keyset, for
the single line station.
APPOINTMENT REMINDER / ALARM
REMINDER
ALARM CLOCK
This feature works like an alarm clock. Use it to remind yourself of an appointment
later in the day (TODAY ONLY) or as a daily reminder every day (DAILY).You can set
up to three alarms. Each one can be either a TODAY ONLY or a DAILY alarm.
When the alarm rings, you will hear three short rings repeated three times. Lift the
handset to answer the alarm. If you do not, the alarm will alert you two more times
at five minute intervals.
Set alarm for desired duration (Everyday, Once). These alarms can be used to
remind you of an appointment later in the day (Once) or as a daily reminder
(Everyday). There are two possible alarms. Each can be either a today (Once) or a
daily (Everyday) alarm.
To set alarms:
•
•
•
•
•
•
Press TRANSFER and then dial 112.
Dial the alarm number 1, 2 or 3.
Dial the time at which you want the alarm to sound. Enter the time as HHMM
(hours and minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY ONLY) or 2 (DAILY) to select the alarm type.
Press TRANSFER to save.
Repeat for each alarm if needed.
To cancel individual alarms:
•
•
•
Press TRANSFER and then dial 112.
Dial alarm number 1, 2 or 3.
Press the HOLD key.
41
From the LCD:
•
•
•
•
•
•
•
•
Press MENU button.
Scroll to E-DIARY option, press ENTER.
Scroll to ALARM option and press ENTER—OR—you may dial 2 and immediately enter the option.
Choose the desired ALARM NUMBER (1/2).
Enter TIME via the dial pad in 24-hour format.
Set RING TONE via the direction button (left/right). Each tone is heard.
Set REPEAT DURATION via the direction button.
Press ENTER when finished.
•
•
•
“T”. Press 2 once to get “A.” Press 5 twice to get “K.” Continue selecting characters from the following table to complete the message.
Enter ALARM ALERT period.
Set RING TONE.
When all information is set, press ENTER.
COUNT
1
2
3
4
5
DIAL 0
<
>
.
)
0
DIAL 1
space
?
,
!
1
To clear alarm:
DIAL 2
A
B
C
@
2
•
DIAL 3
D
E
F
#
3
DAILY PLANNER
DIAL 4
G
H
I
$
4
Scheduling feature with message. Allows the scheduling of up to 30 alarm
reminders. Each of these reminders can have an associated message of up to 32
characters. These reminders can be scheduled to ring one hour before, one half
hour before or right at the exact time set.
DIAL 5
J
K
L
%
5
DIAL 6
M
N
O
^
6
DIAL 7
P
Q
R
S
7
DIAL 8
T
U
V
Q
8
DIAL 9
W
X
Y
Z
9
DIAL
:
=
[
]
•
•
•
•
•
•
•
Scroll to CLEAR option in Alarm Clock setting screen and press ENTER.
Press TRANSFER and then dial 116.
Dial the alarm number 1, 2 or 3.
Dial the time you want the alarm to go off. Enter the time as HHMM (hours and
minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY) or 2 (DAILY) to select the alarm type.
Write your message using the dial pad keys. Each press of a key selects a character. Pressing the next key moves the cursor to the next position. For example, if your message is “TAKE MEDICATION,” press 8 once to get the letter “T.”
Press 2 once to get “A.” Press 5 twice to get “K.” Continue selecting characters
from the following table to complete your message.
Press the TRANSFER key to store the alarm and reminder message.
Repeat for each alarm if needed.
NOTES:
1. When the character you want appears on the same dial pad key as the previous character, press UP to move the cursor one space to the right.
2. Other symbols are available for DIAL #.
ANSWERING THE DOOR PHONE
From the LCD:
When you are programmed to receive calls from a door phone:
•
•
•
•
•
•
•
42
Press direction button UP/DOWN to set the month. Press direction button
LEFT/RIGHT to set the date. Press ENTER on the desired date.
Press MENU then ADD.
Enter the TIME desired for the alarm (in 24 hour format).
Enter the message in the CONTENTS field.
Write your message using the dial pad buttons. Each press of a key selects a
character. Pressing the next key moves the cursor to the next position. For
example, if your message is “TAKE MEDICATION”, press 8 once to get the letter
•
You will receive three short rings repeated.
Lift the handset or press ANS/RLS button. You are connected to the door
phone.
If an electric door lock release is installed, dial 13 to unlock the door.
43
CALLING THE DOOR PHONE/
ROOM MONITOR
You may call the door phone and listen to what may be happening outside or in
another room.
•
•
•
Dial the extension number of the door phone.
You will be connected to the door phone and you can listen or have a conversation.
If an electric door lock release is installed, dial 13 to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press the SPEAKER button.
EXECUTIVE/SECRETARY HOT LINE
•
message and press ENTER (while maintaining contact with t he caller). This
method does not give you the option to transfer the call to another station.
Take necessary action (take message, etc.)
To set up the Executive/Secretary messages (10 each):
•
•
•
•
•
Press BOSS/SECR button and establish a connection.
Press the EXE/SECR MSG button. The first message screen is displayed.
Pressing the DOWN arrow in the upper left corner of the LCD will scroll you to
the second screen. Pressing the UP arrow in the upper right corner of the LCD
will return you to the first screen.
This method gives you the option to transfer the call to another station if so
desired.
Scroll to the desired message.
Press MENU button for options (Send, Edit, and Remove)
SEND - Sends the message to the other end.
EDIT - Enter message from the dial pad.
REMOVE - Deletes message. Use remove option to delete the “Blank Message”
default message.
If programmed, an executive and a secretary can have a hot line between them.
When the executive station is in the DND mode, all of its calls will ring the secretary station.
When an Executive/Secretary hotline is programmed to this keyset, the keyset
offers an additional screen option.This screen has options for setting the status of
the keyset user. This status update is viewable to EasySet users only.
From the BOSS station in DND:
•
•
•
Either person can press the BOSS button to make a voice call to the other station.
Using the hot line will override DND at the other station.This button will have
a flashing indication when the other station is in use.
•
•
•
To transfer a call to a Boss in DND:
•
•
Press the TRANSFER button followed by the BOSS button.
Wait for the BOSS to answer to announce the call and hang up to complete
the transfer—OR—hang up to complete a blind transfer after pressing the
BOSS button.
To send a text message to the Boss display:
•
•
•
•
•
44
Press the TRANSFER button followed by the EXE/SECR MSG soft button.
Scroll to the desired message and press ENTER (the BOSS station gets three
short ring bursts, followed by the message).
This method gives you the option to transfer the call to another station if so
desired.
Press the TRANSFER button again to be reconnected to the caller.
Take the necessary action (the BOSS cancels DND and transfer the call or take
a message)—OR—press the EXE/SECR MSG soft button, scroll to the desired
Receive three short, double ring bursts, followed by the text message from the
Secretary.
Press ENTER to invoke REPLY option—OR—scroll to OK option and press
ENTER.
If REPLY option is activated, the Select Message screen is displayed.
Scroll to the desired message and press ENTER. The message is sent to the
Secretary keyset display and the Secretary station has the option to reply, if so
desired.
Sending a text message from the BOSS keyset to the Secretary keyset, from
the idle condition:
•
•
•
•
Press the EXE/SECR MSG button.
Press the NEXT button (if there are more than two Secretary stations assigned
to that BOSS station, all Secretary keysets will be displayed), in the case of multiple Secretary stations, scroll to the desired Secretary, press the soft key associated with that Secretary and press NEXT button.
Scroll to the desired message and press the associated soft key or ENTER.
The message is sent.
Executive Divert:
•
From the BOSS keyset when the keyset rings, press the EXEC DIVERT button.
The call is forwarded to the Secretary station.
45
•
Pressing the EXEC DIVERT button, when the keyset is in idle status, will divert
all calls after, to the Secretary station. Pressing the EXEC DIVERT button again,
will cancel the divert function.
GROUP LISTENING
•
Press CANCEL to return to Main Config Menu—OR—press END to return to
idle screen.
MANUAL SIGNALLING
When you are engaged on a call and you are using the handset, you may want
other people to hear the distant party’s voice over the speaker:
Use this feature when you want to send a brief 500ms ring burst to another station, regardless of the status of your phone (on-hook, off-hook, handsfree, DND, or
ringing).
•
To send a signal to another station:
•
•
Press the LISTEN button to turn on the speaker.The microphone is not in use,
so the distant party does not hear other parties present in your office.
Press LISTEN again to turn the speaker off and resume private conversation.
Repeat if necessary.
•
•
Press the Manual Signalling (MS) button.
You may press the MS button repeatedly to send multiple signals to the designated station.
NOTE: Depending on speaker volume and the acoustics of your office, it may be
advisable to turn the group listening feature off before hanging up. This will eliminate a momentary squeal.
NOTE: Your phone must have a Manual Signalling (MS) button with a station
number extender assigned to it.
ACCOUNT CODES
OFF-HOOK VOICE ANNOUNCE
When equipped with optional equipment, your system will allow calls to be
charged to a specific account.
Keysets may receive a voice announcement while on another call. The calling station must have an OHVA button. When you are in DND, you cannot receive OHVA
calls. The OHVA feature will work with intercom and transferred calls.
•
•
During any outside C.O. call, press the account (ACC) button.
Enter the 3 digit account code bin number when prompted, OR
If your button has an extender of 000 enter the account code (maximum 12
characters including and #) and press ACC000 again, OR
If your button has an extender other than 000 (001~999) account code contained in that bin will automatically be entered for your.
When you receive an OHVA and secure OHVA is ON, you will hear the announcement in the handset receiver, if you are using the handset. If secure OHVA is OFF
then you will hear the announcement on the speaker, if you are talking on the
handset. If you are using the speakerphone the announcement will always be
heard through the speaker.
LOCKING YOUR KEYSET
To make an off-hook voice announcement:
You can lock your keyset to control misuse of your phone while you are away. You
can unlock it when you return. Your default station passcode is 1234.
•
•
•
•
•
•
•
•
•
•
Press MENU button.
Scroll to CONFIG option. Press ENTER.
Scroll to LOCK option and press ENTER—OR—you may press 2 and immediately access option.
Enter the PASSWORD. Press ENTER.
Use Direction button to scroll LEFT/RIGHT to choose desired mode.
1. UNLOCK - No restrictions. User may complete internal and outside calls.
2. DIS. CALL ORG - Restricted to incoming calls only. No outside calls can be
made.
3. LOCK ALL - No calls, incoming or outgoing allowed to or from the set.
•
46
•
Dial the extension number or press the DSS button.
When you receive a busy signal, press the OHVA button.
After the attention tone, begin speaking.
Finish the call by replacing the handset or pressing the ANS/RLS button.
Press the flashing CALL button on your keyset. This will place the original
party on hold and allow you to talk to the announcing party.
To return to your first party, press the button corresponding to your original
call. This will disconnect the OHVA call.
NOTES:
1. When you are voice announcing to a station close to you, use the handset to
avoid an echo effect.
2. You cannot off-hook voice announce to single line telephones.
Press ENTER.
47
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (BLOCK) button. Pressing
this button will prevent anyone from making an OHVA to you until you press the
button again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (REJECT) button. Pressing
this button while receiving an OHVA call will disconnect the voice announcing
party and return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group, you can remove your keyset from
the group and then put it back in. While you are out of the group, you can receive
calls to your extension number but not calls to the group number. If you have an
IN/OUT button with the group number assigned.
•
•
Press the IN/OUT button. The button indicator will be lit steady when your
keyset is in the group.
Press the IN/OUT button again to exit the group and the indicator will go
blank. Repeat as necessary.
If you do not have an IN/OUT button:
•
Dial the IN/OUT access code number ________________, then the group
number, then 0 to exit the group or 1 to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press SPEAKER button.
The IN/OUT button can include an extender to indicate the specific group that
this button will affect. This means that if you are in multiple groups, you can decide for which groups you will receive calls.
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME feature to enable password protection.
This will prevent unauthorized people from listening to your messages being left.
The passcode is the same as your station passcode. This feature only applies if
there is a SVM card installed in the system and your keyset has a programmed
AME button.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 101 to turn on AME PASSCODE or 100 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option and press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to AME password and press ENTER to change status.
Press CANCEL to return to the Main Option Page—OR—press END to return
to the idle screen.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on, if possible, when
a busy station is called.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Press 081 to turn CAMP-ON on or 080 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
48
Press MENU button.
Scroll to CONFIGURATION option and press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to AUTO CAMP-ON and press ENTER to change status.
Press CANCEL to return to the Main Option Page—OR—press END to return
to the idle screen.
49
SELECT RING TONE
SET ANSWER MODE (INTERCOM)
Each keyset user can select any one of eight ring frequencies.
You can receive internal calls in one of three modes (see Answering Intercom Calls
under Intercom Calls for descriptions).
•
•
•
While on-hook, press TRANSFER and then dial 111.
Dial 1–8 or press the UP and DOWN keys to hear each tone.
When you hear the tone that you prefer, press TRANSFER to save it.
NOTE: Specific lines or stations may be programmed to ring with a different
tone than what you have selected for your keyset.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to VOLUME option and press ENTER.
Scroll to RING TYPE and press ENTER—OR—you may dial 1 and immediately enter the option.
Scroll to RIGHT/LEFT to choose tone and press ENTER at the desired tone.
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 0000.You can change your station passcode whenever you desire.
•
•
•
•
•
While on-hook, press TRANSFER and then dial 101.
Dial your old passcode.
Dial a new passcode (must be four characters). You can use 0–9.
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
Press TRANSFER to store the new passcode.
•
•
•
While on-hook, press TRANSFER and then dial 103.
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option and press ENTER.
Scroll to ANSWERING MODE and press ENTER—OR—you may dial 3 and
immediately enter the option.
Scroll RIGHT/LEFT to select desired station ring type setting. (Ring, Automatic,
Broadcast [Voice Announce]).
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
NOTE: When your keyset is programmed for Auto Answer and you have Forward
No Answer (FNA) turned on, you must answer screened transfers by pressing the
ANS/RLS button before your FNA timer expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
•
•
•
While on-hook, press TRANSFER and then dial 110.
Dial 15 to access AUTO ANS CO.
Press the VOLUME UP or DOWN key to change status.
Press TRANSFER to store your selection.
From the LCD:
AUTOMATIC HOLD
•
•
•
While on an outside call, pressing a line button, route button or a flashing CALL
button will automatically put your call on hold and connect you to the next call.
This feature can be turned on or off at your keyset.
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option and press ENTER.
Scroll to PASSWORD and press ENTER—OR—you may dial 1 and immediately enter the option.
Enter CURRENT PASSWORD, press ENTER.
Enter NEW PASSWORD and press ENTER.
Enter NEW PASSWORD again, for confirmation and press ENTER.
Press CANCEL to return to the Main Option Page—OR—press END to return
to idle screen.
•
•
•
From the LCD:
•
•
50
With the handset on-hook, press TRANSFER and then dial 110.
Dial 001 to turn Automatic Hold on or 000 to turn it off.
Press TRANSFER to store your selection.
Press MENU button
Scroll to CONFIGURATION option and press ENTER.
51
•
•
•
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to AUTO HOLD, press ENTER to change option status.
Press CANCEL to enter change and return to the Main Configuration Menu—
OR—press END to return to idle screen.
•
•
•
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to HOT KEYPAD, press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
NOTE: Intercom calls can be automatically put on hold by pressing TRANSFER.
KEY CONFIRMATION TONE
HEADSET OPERATION
You can hear a short beep (confirmation tone) each time you press a button on the
dial pad. This tone can be turned on or off.
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the ANS/RLS button to answer and release calls.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 021 to use the headset or 020 to use the handset.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option and press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to HEADSET USE and press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
Your keyset may be equipped with a Headset mode button. If it is so equipped
pressing this button while the button indicator is blank will cause the keyset to
enter headset mode and the button indicator to be lit solid to indicate this.
Pressing the button while the button indicator is lit solid will cause the keyset to
return to handset mode and the button indicator will go blank.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live” or “hot” so that it is
not necessary to lift the handset or press the SPEAKER button before you begin
dialing. Calls can be made and features activated by simply dialing the C.O. line
number, trunk group access code, intercom number or feature access code.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 031 to turn the Hot Keypad on or 030 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
52
•
•
•
While on-hook, press TRANSFER and then dial 110.
Dial 040 to turn tones off or 041 to turn tones on.
Press TRANSFER to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 051 to turn this feature on or 050 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION OPTION and press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to PAGE REJOIN, press ENTER to change option status.
Press CANCEL to enter change and return to the Main Configuration Menu—
OR—press END to return to idle screen.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or press
the ANS/RLS button.This method will always answer calls in the order they arrived
at your keyset.When you turn ring preference off, you must press the flashing button to answer a call, allowing you to answer calls in the order you choose.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 061 to turn ring preference on or 060 to turn it off.
Press TRANSFER to store your selection.
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
53
From the LCD:
•
•
•
•
CALLER ID REVIEW ALL
•
•
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and immediately enter the option.
Scroll to RING PREF, press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
AUTO ANSWER CO CALLS
This option will allow CO calls that directly ring your phone to auto answer. When
a CO call arrives at your station and this option set for ON your phone will sound
two beeps, the same as when a screened transfer is completed, and you will be
connected to the CO call. In order for this option to work the station must also be
programmed for auto answer (see Set Answer Mode).
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and immediately enter the option.
Scroll to AUTO ANS CO CALL, press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
NOTE: Outside lines must ring your station directly for the Auto Answer CO to
work. Lines ringing a station group will not cause your phone to Auto Answer the
call.
DISPLAY SPEED DIAL NAME
This option allows you to view the name associated with a speed dial number as
it is dialed.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 111 to turn DISP SPDNAME on or 110 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
54
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
This feature allows display keyset users to review Caller ID information for calls
sent to their stations.This list can be from ten to fifty calls in a first in, first out basis.
The list includes calls that you answered and calls that rang your station but that
you did not answer. When reviewing this list, you can press one button to dial the
person back. The system must be using LCR to dial the stored number.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 121 to turn CID REVIEW ALL on or 120 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and immediately enter the option.
Scroll to CID REVIEW ALL, press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
SECURE OHVA
This option allows you to receive OHVA calls via the speaker while you are on the
handset.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 131 to turn AUTO CAMP-ON on or 130 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
Scroll to CONFIG and press ENTER—OR—you may press 0 and immediately
enter the option.
Scroll to AUTO CAMP-ON and press ENTER to change status.
Press CANCEL to return to option Main Screen.
Press the MENU button—or press the END to return to idle screen.
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and immediately enter the option.
Scroll to DISP SPDNAME, press ENTER to change option status.
55
DISPLAY FEATURES
DIRECTORY INFORMATION
An 11 character directory name can be assigned to each extension number.
Display keyset users can view the name of the called or calling station before answering.
Each outside line can have an 11 character directory name. Incoming calls can be
easily identified and answered with different greetings.
Outside and internal calls ringing to a station group will display [CALL FOR xxx]
where xxx is the station group number. This allows you to answer calls directed to
you differently than calls directed to your group.
CALL LOG
The system can log both incoming and outgoing calls placed from or to your telephone. You must have a LOG button programmed on your keyset and assigned a
review list.
Each IN and OUT list can be up to 50 numbers maximum. They are assigned in
blocks of 10 each.
•
•
•
•
•
•
Press the LOG key.
Press either the IN or OUT key.
View the first IN/OUT telephone number. At this point you may select one of
the three options related to this number or use the UP/DOWN keys to scroll
through your list of calls.
Press the CLEAR button to erase this number from the list.
Press the NND key repeatedly to view the Name, Number, or Date associated
with this call.
Press the DIAL key to call this number.
These options are the same for the incoming or outgoing call logs.
56
DIAL BY NAME
Each station or speed dial number can have an associated directory name. A station or speed dial number can be selected by scrolling alphabetically through a
directory name list. This on-line “phone book” allows the user to look up and dial
any station or speed dial number in seconds.
•
•
•
•
•
•
•
•
•
Press MENU button
Scroll to P-BOOK option, press ENTER.
Scroll to SEARCH and press ENTER—OR—you may dial 1 and immediately
enter the option.
Scroll to BY NAME, press ENTER.
Enter NAME to search for and press ENTER.
Name is displayed, press ENTER, number is displayed.
Press SEND button to automatically call by number.
Press MENU button for more options.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
You can also use the Dial by Name feature by following these steps:
•
•
•
•
•
Press the DIR button (DIRECTORY).
Select the directory you wish to use: PERS (personal speed dial numbers), SYS
(system speed dial numbers) or STN (station names).
Dial the button on the keypad that corresponds to the first letter of the name
you wish to search for.
Use the UP and DOWN arrows to scroll through the names.
Press the DIAL soft key to dial the number.
NOTE: A DIR button can have an extender to take you directly to one of the above
lists (PERS, SYS, or STN).
CALL PROGRESS DISPLAYS
During everyday call handling, your keyset display will provide information that is
helpful and in some cases invaluable. Displays like [CALL FROM 203], [TRANSFER
TO 202], [701: RINGING], [TRANSFER FM 203], [708 busy], [Camp on to 204], [Recall
from 204], [Call for 501], [message frm 204] and [FWD ALL to 204] keep you informed of what is happening and where you are. In some conditions you are
prompted to take an action and in other cases you receive directory information.
57
DISPLAY NUMBER DIALED
VIEWING MESSAGE INDICATIONS
Display keysets begin showing digits as they are dialed. They will stay in the display until the call duration timer comes on automatically or the TIMER button is
pressed. If the call duration timer is not used, the number dialed will be displayed
until the call is released, transferred or put on hold.
You can view all of your message indications before you return them:
CALL DURATION TIMER
The system can be set to automatically time outside calls. A few seconds after you
dial a telephone number, the timer appears in the display. It appears immediately
for incoming calls. The call timer continues for the duration of the call. Call duration times are displayed in minutes and seconds. If a call lasts longer than 60 minutes, the timer restarts.
You can press the TIMER button to manually begin timing a call. Press it again to
stop timing. If you press it while the automatic timer is on, the call duration time
is restarted.
AUTO TIMER
Display keyset users may have the timer automatically start when they answer
incoming calls or after a short delay on an outgoing call.
•
•
•
With the handset on-hook, press TRANSFER and then dial 110.
Dial 011 to turn the auto timer on or 010 to turn it off.
Press TRANSFER to store your selection.
From the LCD:
•
•
•
•
•
•
Press MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to STATION ON/OFF and press ENTER—OR—you may dial 0 and
immediately enter the option.
Scroll to AUTO TIMER, press ENTER.
Press ENTER to change option status.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
TIMER FUNCTION
Display keyset users may use this feature as a simple stopwatch.
•
•
•
•
58
When the keyset is idle, press the TIMER button to start timing.
Press the TIMER button again to stop timing.
Read the elapsed time in the display.
Lift the handset and replace it. The display will return to date and time.
•
•
•
•
With the handset on-hook, press the MESSAGE button with the flashing indicator.
The first station that left a message indication will be displayed.
Press the UP and DOWN arrows to scroll through the stations that left message indications. Use the soft keys to reply, clear or advance to the next message.
Press the END button to return your keyset to the idle condition.
PERSONAL SPEED DIAL NAMES
Each personal speed dial number can have an 11 character name assigned to it.
This name is used to select the speed dial bin when you are dialing by directory.
•
•
•
•
•
Press TRANSFER and then dial 106.
Dial the speed dial bin number 00–49.
Write your message using the procedure described in Alarm Reminder.
Press the TRANSFER key to store the speed dial name.
Repeat for each speed dial bin if necessary.
See Programming Personal Speed Dial Numbers Section.
STATION NAMES
See Application Program Menus—My Phone.
MANAGING KEY ASSIGNMENTS
You can view your key assignments and add extenders to some of your programmable keys for easy one touch operation of frequently used features.
•
•
•
•
While on-hook, press TRANSFER and then dial 107.
Use the VOLUME buttons to scroll through all of your programmable buttons
OR press the programmable button to which you want to add the extender.
When you reach a key listed below, dial the corresponding extender.
Press TRANSFER to store and exit programming.
Please refer to the Enhanced Display Programming Section provided by your installation company when requested for a complete list of descriptions and extenders
for any keys you may have programmed on your keyset.
NOTE: Confirm that the cursor is placed correctly before you enter the extender.
59
LCR WITH CLEAR
STATION 201: LINDA
received a call on line 702
When you are making outside call using LCR and dial an incorrect digit, you can
press the CLEAR soft key to reenter the telephone number. You do not need to
redial 9 to reaccess LCR.
Talking on line 702
BACKSPACE WITH LCR
If you misdial while using LCR, you can delete digits shown in the display by pressing the BACKSPACE soft key as many times as necessary.
TEXT MESSAGING
See also MESSAGE option in the Application Program Menus section.
This feature allows two digital keyset users to respond to each other with preprogrammed messages. After receiving an Off Hook Voice Announcement or Station
Camp-On, you may respond with a text message while continuing to talk and listen to your outside party. The other station can view this message and take the
appropriate action or respond back with another text message.
There are 1000 messages assignable to stations in blocks of 10, stored in system
memory that can be sent to another display keyset. Only the display keysets that
are allowed in system programming (MMC 611) will receive the TEXT MESSAGE
soft key in the display and use this feature.
702:
CONF
01:15
MUTE
PAGE
05:25
Transfer:
RETURN
Dial 205
205:busy
OHVA
CAMP ON
Ð
OHVA to 205
OHVA from 201
TMSG
REJECT
Wait for reply
GIVE THE CALL
TMSG:01
SEND
Dial 03 or press Ï twice
ASK THEM TO HOLD
TMSG:03
SEND
Ð
The basics steps in text messaging are:
Press TEXT MESSAGE soft key to begin text messaging.
Dial the 2 digit number for the desired message.
Confirm this is the intended message then press SEND.
Wait for a reply from the other station (steps 1, 2 & 3)
When any station presses EXIT the displays at both stations return to their
previous call progress condition.
701:
Press TRANSFER
Familiarization with the two digit message numbers you will use the most will
make this procedure quick and easy. However if you do not know them, use the
UP/DOWN button to scroll to the desired message, then press SEND.
1.
2.
3.
4.
5.
STATION 205: JOHN
is talking on line 701
ASK THEM TO HOLD
TMSG
EXIT
Ð
Wait for reply
702:
CONF
701:
CONF
PAGE
01:45
MUTE
PAGE
05:55
MUTE
At all times after step 1 you can talk and listen to your caller while repeating steps
2.
The example on the following page will better demonstrate how to use Text
Messaging. In this example station 201 is making an off hook voice announcement to station 205 who after hearing the announcement will respond with a text
message.
60
61
CALLER ID
SELECTING YOUR CALLER ID DISPLAY
You can decide if you want to see the Caller ID name or Caller ID number in the
display. Regardless of which one is selected, you can press the NND button to view
the other pieces of Caller ID information. To select the type of Caller ID information you wish to view first.
•
•
•
•
With the handset on-hook, press TRANSFER and then dial 119.
Dial 0 for CID options, 1 for ANI options, or 2 for CLI options.
Dial 0 if you do not wish to view CID information, 1 to view the NUMBER first
or 2 to view the NAME first.
Press TRANSFER to exit and store your selection.
REDIALING A SAVED CALLER ID NUMBER
To redial a number that has been saved, press the SNR button or dial 17.
NOTES:
1. Your telephone system must be LCR correctly programmed to redial the
saved number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPEAKER button before you begin.
STORING A CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may save
the CID number as a speed dial number in your personal speed dial list. To store a
Caller ID number in a personal speed dial bin:
•
From the LCD:
•
•
•
•
•
Press the MENU button.
Scroll to CONFIGURATION option, press ENTER.
Scroll to CID DISPLAY and press ENTER—OR—you may dial 6 and immediately enter the option.
Scroll LEFT/RIGHT to desired display option.
Press CANCEL to enter change and return to Main Configuration Menu—
OR—press END to return to idle screen.
VIEWING THE NEXT CALLER ID CALL
In the event that you have a call waiting or a camped-on call at your keyset, you
can press the NEXT button to display the Caller ID information associated with
the call in queue at you keyset. Either the CID name or CID number will show in
the display depending on you Name/Number selection.
To view Caller ID information for calls that have been camped-on to your keyset,
press the NEXT button.
SAVING THE CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may press
the SAVE button to save the CID number. The system must be using LCR to dial
the saved number.
•
•
NOTE: Your telephone system must have LCR correctly programmed to redial the
saved number. If LCR is not being used on your system, you will not be allowed to
STORE CID numbers.
INQUIRE CALLER ID PARK/HOLD INFO
If you are informed that an incoming call is on hold or has been parked for you,
you may view the Caller ID information before you retrieve the call.This may influence how you choose to handle the call.
From an idle keyset:
•
•
•
Press the INQUIRE button—OR—press the CID button and then the
INQUIRE soft key.
Dial the trunk number.
You may now answer the call by pressing the ANS button—OR—you may
use NND to view more information about this call—OR—you can return to
the idle condition by pressing IGNORE.
If you are on a call:
•
62
Press the STORE button. The system displays the speed dial bin in which the
number was stored—OR—press the CID button and then press the SCROLL
button.
Press the STORE soft key.
The system displays the speed dial bin in which the number was stored.
Press the INQUIRE button. Your existing call will go on hold—OR—press the
CID button and then the INQUIRE soft key to place the first call on hold.
63
•
•
Dial the trunk number.
You may now answer the call by pressing the ANS button—OR—you may
use NND to view more information about this call—OR—you can return to
the idle condition by pressing IGNORE.
NOTES:
1. If you are on an intercom call or you have Automatic Hold turned off, you
must finish the existing call or place it on hold before inquiring.
2. If you inquire about an outgoing call, you will receive a [call no longer available] display.
REVIEWING PAST CALLER ID CALLS
This feature allows you to review CID information for calls sent to your keyset.This
list can contain 10–50 calls in a last-in, first-out basis.The list includes calls that you
answered and calls that rang your keyset but that you did not answer. When
reviewing this list, you can press one button to dial the person back. The system
must be using LCR to dial the stored number.To access the CID information stored
in your REVIEW list:
•
•
•
Press the REVIEW button—OR—press the CID button and then press the
REVIEW soft key.
If you have entries in your review list, the most recent call will be shown first.
You can now CLEAR this entry—OR—use NND to view more information
about this call, OR
Press DIAL to call this person back—OR—press SCROLL and then press
STORE to save this number in a personal speed dial bin.
NOTES:
1. Each keyset defaults with ten review bins. Please see your system administrator to determine the number of bins assigned to your keyset.
2. Your system must have LCR correctly programmed to allow you to DIAL numbers from the review list or to STORE entries from the review list.
APPLICATION PROGRAM MENUS
Much of the call processing of the ITP 5012L can be accomplished by using the
various feature/function screens on the LCD. Below are instructions for additional
call processing and special applications that can be accomplished via the LCD
programming. These screens, features and functions can be accessed by pressing
the MENU button. Follow the below user information to utilize these features and
functions.
After pressing the MENU button,
use the direction button to highlight desired menu icon. For multiple screen options, the UP/DOWN
arrows at the top left and right
sides of the LCD may be used to
scroll on a per page basis. Press
ENTER to access that menu.To navigate within the menu, you may
scroll to the desired option/function, dial the associated option
function number or press the associated select button on either side
of the display.
Application Program Main Menu Screen
Press END button to exit programming.
PHONEBOOK
Refer to Speed Dialing and Programming Section.
E-DIARY
1. WAKE UP CALL: Set Wake Up call for desired duration (Everyday, MondaySaturday, Monday-Friday). Using the direction button scroll UP/DOWN to the
desired option and LEFT/RIGHT to scroll to desired option setting.
•
•
•
•
Enter TIME via dial pad in 24-hour format.
Set RING TONE via direction button (LEFT/RIGHT) Each tone is heard.
Set REPEAT DURATION via direction button.
Press ENTER when finished.
2. ALARM: See Alarm Reminder Programming Section.
64
65
3. DAILY PLANNER: See Alarm Reminder Programming Section.
•
4. MEMO PAD: Self memo feature. Allows you to set text message notes. Up to
5 memos may be stored.
•
•
•
TEXTMSG. SETUP: Set incoming text message signal for specific functionality. Scroll DOWN to desired option, scroll LEFT/RIGHT to desired
option setting.
INDIVIDUAL INTERVAL: Sets notification for Once, Every Two Minutes,
No Tone.
INDIVIDUAL TONE: Sets incoming notifications signal.
SHOW CONTENTS: Sets display option of received message. (Save - On,
Clear - Off )
Add NEW MEMO: Type in memo on keypad, press ENTER.
Press MENU button to change fonts or add characters.
SEARCH displays all memos saved and REMOVE ALL deletes all memos.
5. CALCULATOR
•
•
Enter FIRST NUMBER, press SOFT KEY associated with the proper operation.
Enter SECOND NUMBER and press ENTER to display answer.
2. SENT: Used to store and view text messages sent from the station.
WRITE MESSAGE :
6. WORLD TIME: Displays times throughout the world.
•
•
•
•
Use direction button, LEFT/RIGHT to view desired time zone.
7. D-DAY PLUS: Scheduling feature that allows the user to view the time left
until an event, or time since event occurred. Use to monitor deadlines, schedules, etc.
•
•
•
•
•
•
•
•
Choose desired function (LENGTH, WEIGHT, AREA, VOLUME,
TEMPERATURE), press ENTER.
Scroll LEFT/RIGHT to select base unit.
Scroll DOWN and ENTER VALUE to be converted.
Scroll DOWN, select CONVERSION UNIT.
Press ENTER to display answer.
MESSAGE
1. RECEIVED: View received text message information. (Station number, text
message, time/date) and set notification of messages received. A maximum
of 10 messages may be stored.
•
•
66
MSG. CHARGE: Number of messages saved, press ENTER to view messages.
Press MENU button to display further options.
Write NEW MESSAGE, enter STATION NUMBER to send message to.
Scroll DOWN, enter MESSAGE via dial pad.
Press ENTER.
INVOKE MESSAGE : Allows saved messages in Draft option for future delivery.
Enter DATE, FREQUENCY and MEMO, press ENTER.
When entering Memo, press MENU to change fonts or add characters.
Enter Base Date and number of days before or after to begin reminder.
8. UNIT CONVERT: Weights and Measures conversion application. Allows you
to convert units of weights and measures into other units.
Return calls by highlighting the desired phone/station number and press
the SEND button.
•
•
Press ENTER, displays all saved messages.
Press MENU for message options (Add - New message to list, Modify - a
current message in the list, Send - selected message, Delete - selected
message.)
3. DRAFT: Allows creating and storage of messages for future delivery, or as
reminders. You can view stored messages, Search through stored messages,
Remove all stored messages.
•
•
•
NEW MESSAGE: Use keypad to add new message to list, for future delivery.
SEARCH MESSAGE: Displays all messages in list.
RM, ALL MESSAGE: Deletes all messages in the list.
VOLUME
Used to set volume levels of the various functions of the keyset. Scroll left/right to
select desired option setting. When setting Ring Type and Ringer volume, each
tone level will be heard as you scroll through them.
1.
2.
3.
Ring Type: Assigns ringer tone to station. (8 tone options)
Ringer: Sets ringer volume level. (8 volume levels)
Offhook: Sets off hook ringer volume level. (8 volume levels)
67
4.
5.
6.
Handset : Sets handset receive volume level. (8 volume levels)
Speaker: Sets station speaker volume level. (16 volume levels
Broadcast: Voice Announce feature volume. (16 volume levels)
CALL FORWARD
9. DIAL MODE: Select dial type options. (enblock-requires SEND button to complete the call, or overlap - direct out dial)
•
•
•
Scroll to or dial 9, press ENTER.
Scroll LEFT/RIGHT to select desired display option.
Press ENTER, display confirms save.
See Transferring Calls Section, Forwarding Calls.
0. STATION ON/OFF: Turn various features/functions on/off in the keyset.
CONFIGURATION
1. PASSWORD: See Customizing Your Keyset Section, Change your Passcode.
2. LOCK: Station Lock programming. See Convenience Feature Section, Locking
Your keyset.
These features are:
AUTO HOLD: When on an outside call, pressing a line button, route button or
flashing CALL button will automatically put your call on hold and connect
you to the next call.
AUTO TIMER: Timer in LCD that monitors call duration.
3. ANSWERING MODE: See Customizing Your Keyset Section, Station Answering
Mode Programming.
HEADSET USE: Switches between headset and handset use.
4. BOSS ANSWERING: Allows setting of ring type for Bosses station, from
Secretary station.
PAGE REJOIN: Allows remaining portion of internal page to be played
through keyset speaker, after handset is replaced.
•
•
•
Scroll to or dial 4, press ENTER.
Scroll LEFT/RIGHT to select desired Bosses RING TYPE setting. (Ring,
Automatic, Broadcast(voice announce).
Press ENTER, display confirms save.
5. LANGUAGE: Select station display language programming.
•
•
•
Scroll to or dial 5, press ENTER.
Scroll LEFT/RIGHT to select desired display language.
Press ENTER, display confirms save.
6. CID DISPLAY: Select station incoming CID information display.
•
•
•
Scroll to or dial 6, press ENTER.
Scroll LEFT/RIGHT to select desired display option.
Press ENTER, display confirms save.
7. ABSENT MESSAGE: See Paging and Messaging Section.
8. INTERNAL CALL: Select incoming information display from internal caller.
(Number or Name)
•
•
•
68
Scroll to or dial 8, press ENTER.
Scroll LEFT/RIGHT to select desired display option.
Press ENTER, display confirms save.
HOT KEYPAD: Allows for dialing without lifting handset first.
RING PREF: Allows for automatically answering of calls when handset is lifted. (Does not require button press)
AME PASSWORD: Allows password protection of AME feature on set. This
prevents unauthorized listening to messages being left.
AUTO CAMPON: Allows intercom calls to be automatically camped on to,
when a busy station is called.
DIS SPDNAME: Allows the speed dial associated name to be displayed while
number is being dialed.
SECURE OHVA: Allows OHVA calls to be received by station in conversation
on handset.
CALL COST DISP: Display in LCD that monitors call cost, for duration of call.
CID REVIEW ALL: Allows user to review Caller ID information for calls sent to
the station. The list is programming dependent and operates on a first in first
out basis. Calls to displayed numbers can be returned with a single button
press, provided LCR is being used.
STOP CID DISPLAY: Discontinues CID information after call is answered.
AUTO ANS CO CALL: Allows CO calls to be auto answered on incoming calls.
•
•
•
Scroll to or dial 0, press ENTER.
Scroll to desired feature, press ENTER to change option status.
Press CANCEL to enter change and return to main Configuration menu.
69
MY PHONE
STATUS SCREEN OF THE LCD PANEL
Used to personalize your keyset.
1. SELECT BG: Select LCD background scenery. (Calendar, Seasons)
•
•
•
Scroll to or dial 1, press ENTER.
Scroll UP/DOWN to desired background.
Press ENTER, saves selection and returns to My-Phone option screen.
2. MY NAME: Allows an 11character name to be assigned to the keyset. This
information is sent to internal display keysets on incoming and outgoing
calls.
•
•
•
Press TRANSFER and then dial 104.
Enter the 11 character name using the procedure described in Alarm Reminder.
Press TRANSFER to store the name.
• Executive-Secretary: Station is programmed for Executive-Secretary feature.
• Forward: Call Forwarding is set to station.
• Answer Mode: Station is set for Auto Answer or Voice Announce mode.
• Do Not Disturb: Station is set for Do Not Disturb.
• Headset: Station is set for Headset mode operation.
• Group Listen: Station has enabled Group Listen feature.
• Mute: Station has enabled Mute feature.
• Alarm: Station has set an Alarm Reminder.
• Message: Station has received a message from another station.
• Network Connection: Indicates Network Connection is operational.
From the LCD:
•
•
•
Scroll to or dial 2, press ENTER.
Enter name. (Press MENU button to change form upper to lower case,
etc.)
Press ENTER, display confirms save.
3. NETWORK INFO: View IP information for the keyphone. (IP Address, NetMask,
Gateway, Server IP, MAC Address).
4. STATUS INFO: Status Info - Displays status of various station features.
•
•
•
Scroll to or dial 4, press ENTER.
Displays status of station forwarding. Absent message, DND and Lock.
Press CANCEL to return to MY-Phone Main Menu.
5. ENBLOCK TIMEOUT: When enblock dialing used, this is the screen clear time,
if call is not sent. (SEND button not pressed)
•
•
•
70
Scroll to or dial 5 press ENTER.
Scroll LEFT/RIGHT to desired time option.
Press ENTER, display confirms save.
71
SVMi-8/SVMi-16E
This section describes how to setup and use the various features available to a
Subscriber. A Subscriber is a person that has been authorized access to the various features and services available in the SVMi-8/SVMi-16E. Please review this section carefully before you use your Authorized Features and Services, known as
Subscriber Services.
Voice Mail is one of the Subscriber Services available. Your voice mail box has the
capability of storing private messages, and offers a number of options for sending
or redirecting messages as well as provides several ways to notify you of new messages.
Another very common Subscriber Service is Access Manager.This allows you control over when and where you receive your calls as well as what to speak to your
callers in the event you are unable to speak to them directly. The ‘events’ are
referred to as “Call Conditions”. No-Answer, Busy, and Blocked are the most commonly used Call Conditions.
This guide can be used by Subscribers from within the office or from telephones
outside the office. The basic operation is the same, but the access method will be
different. See the SVMi-8/SVMi-16E Subscriber Services Menu Diagram for more
details.
Note that some features and prompts detailed here may not be available to all
Subscribers. See your System Administrator if you have questions about feature
availability.
ACCESSING YOUR MAILBOX
[Also known as Subscriber Services Menu]
Inside Callers [Subscriber logging in from their Desk]
•
•
Dial the SVMi-8/SVMi-16E access number or press the key assigned to ring
SVMi-8/SVMi-16E [VMMSG].
Enter your personal password when prompted (the default password is
0000).
Outside Callers [Subscribers calling from Cell Phones or outside of the
office environment]
•
•
•
Dial the phone number that will be answered by the SVMi-8/SVMi-16E. The
main greeting will answer.
At the main greeting dial [#] plus your Subscriber (or mailbox) number
(Subscriber and Mailbox numbers will usually match your extension number).
Enter your personal password when prompted (the default password is
0000).
Access your Subscriber Services (or Mailbox) from a Station
other than your Own (or checking a mailbox associated with a
different station)
•
•
•
Press the [VMMSG] key or dial the SVMi-8/SVMi-16E group number.You will
be prompted to enter a password.
Press [ ]. This will take you to the Main Auto Attendant Menu.
Press [#] plus the Subscriber number of your choice. You will be prompted to
enter you password.
At this point the inside and outside callers follow the same instructions. You will
hear a message stating the number of messages left in your mailbox.You will then
hear the Subscriber Services Menu with the following options:
1
Listen to New Messages - See Listening to your Message.
2
Record and Send Message - See Sending Messages.
3
Review Saved Messages - See Listening to your Message.
4
Access Manager - See Access Manager.
5
Personal Greetings - See Personal Greetings.
6
Mailbox Administration - See Mailbox Administration.
#
Personal Services - See Personal Services.
Return to Main Menu.
72
73
SVMi-8/SVMi-16E Subscriber Services Menu
SVMi-8
Subscriber Services
Services Menu
Calais Executary
Menu
Group New
Messages
Group Saved
Messages
11
33
Listen to New Review Saved
Messages
Messages
Group Messages Menu
1
Group
Urgent Messages
2
Group
Callback Requests
3
Group
Reminders
4
5
6
7
8
Group
Private Messages
Group
Fax Only Messages
Group
Voice Only Messages
Group
Email Only Messages
Pause, Resume
Menu Prompting
1
Listen Menu
1
11
3
Discard
Message
4
Reply to Sender
5
Place
Call to Sender
55
Private Access
Numbers
Personal
Services
Pause, Resume
Executary
Play Menu
Options
Exit
Executary
2
4
5
6
7
#
8
0
*
Forward a
Copy of Message
7
Rewind
5 Seconds
Play
Message Inventory
8
9
99
#
##
##
1
Follow Me
1
Assign and/or Edit
Primary Greeting
1
Change
Message Alert
For a Directory
of Subscribers
2
Caller Access
2
Assign and/or Edit
Busy Greeting
2
Change
Pager Notification
To Create a
Reminder
3
Block All Calls
3
Assign and/or Edit
Blocking Greeting
3
Review Deleted
Messages
1
4
Call forwarding
4
Assign and/or Edit
Night Greeting
4
Review Undelivered
Messages
5
Call Screening
5
Assign and/or Edit
Screened Greeting
5
6
Find Me
6
Edit Only
Personal Greetings
7
Auto Set
Night Intercept
7
8
Pause, Resume
Menu Prompting
#
Play
Access Coverage
0
Play
Menu Options
"Enter the Recipient's Number"
Deliver Copy
of Fax Message
6
#
Cancel, Return
Return
Subscriber Services
to Executary
Mailbox
Administration
#
Play Previous
Message
Save
Message
77
*
Personal
Greetings
Record Menu
Play
Message
2
Group
A Specific Sender
Play
Menu Options
Access
Manager
3
9
0
Record & Send
Messages
Change
Playback Volume
Pause, Resume
Message Playback
Fast Forward
5 Seconds
Change
Playback Speed
Skip to
Next Message
Scan Messages
1
Review
Recording
2
Stop, Append to
Recording
3
Discard Recording
and Rerecord
4
Set
Delivery Options
5
Specify
Future Delivery
6
SEND Message,
Then Copy
7
Rewind
5 Seconds
77
Change
Playback Volume
8
Pause, Resume
Record/Playback
9
Fast Forward
5 Seconds
Review
Workload
"Enter the PAN ID Number"
2
Edit Stored
Telephone Numbers
Review
PAN Message
3
Change
Weekly Schedule
1
Change
Password
2
Record
PAN Message
5
Place a
Direct Call
2
Record
Name
Auto Play
New Messages
3
Delete
PAN message
6
Programmed
Services
3
Select
Enter Directory
Language
Name
6
Auto Play Message
Information
4
Change
Access Privilege
7
Personal
Administration
4
Extended
Prompting
Edit Only
Mailbox Greeting
8
Pause, Resume
Menu Prompting
5
Place a Direct
Call to PAN
8
Pause, Resume
Menu Prompting
8
Pause, Resume
Menu Prompting
8
Pause, Resume
Menu Prompting
9
Record &
and
Send
Record
Sent
Broadcast Message
Broadcast
Message
6
Change PAN
Message Duration
9
Subscriber
Administration
0
Play
Menu Options
0
Play
Menu Options
0
Play
Menu Options
7
PAN Telephone
Numbers
#
Record
a Reminder
Cancel, Return
Return
to Subscriber
Executary Services
8
Play
Access Statistics
0
Play
Menu Options
9
Clear
PAN ID Record
#
Save, Goto
Next PAN ID
0
Play
Menu Options
*
Cancel, Return
to
to Executary
Subscriber Services
*
Change
Playback Speed
00
*
Play
Menu Options
#
SEND Message,
Then Exit Record
00
Play Message
Information
0
Play
Menu Options
Cancel, Return
Return
Subscriber Services
to Executary
Cancel, Return
Return
Cancel,
toSubscriber
Executary Services
to
1
99
0
*
*
For a Directory
of PANs
#
*
*
*
Cancel, Return
Return
to Services
Menu
Subscriber
Services
Cancel,
Return
Cancel, Return
Executary Services
to Subscriber
Access
Statistics
Cancel, Return
to Executary
Cancel,
Return
Cancel, Return
to Subscriber
Executary Services
NOTE: All options shown MAY NOT be authorized. If an option is not available
please speak to your system administrator.
74
75
GETTING STARTED
0
Using your new SVMi-8/SVMi-16E Subscriber Services is as simple as following a
few simple spoken instructions. First time users should read this section as a tutorial. You should start with the following steps:
#
•
Access your Subscriber Services Menu - You already know how to do this.
From the Subscriber Services Menu:
•
•
•
•
•
Record a Primary/No-Answer Personal Greeting. Dial [5][1].
Record a Mailbox Greeting. Dial [5][7].
Change your access code (Password). Dial [#][7][1].
Record your name. Dial [#][7][2].
Enter your directory name. Dial [#][7][3].
After you have completed the steps above your Subscriber Services are set up and
ready to use.
EXIT TO AUTO ATTENDANT
LISTENING TO OLD OR NEW MESSAGES
1
Play / replay the message you just heard.
11
Play the previous message.
2
Save the message you just heard and listen to the next message.
3
Delete the message you just heard and listen to the next message.
4
Reply to the message.
This will allow you to leave a message in the mailbox of the sender (if the
sender has a mailbox on this system).
5
Return the call directly to the telephone number that left the message.
This will work for internal and external callers, but Caller ID service is needed to use this feature on an outside call.
55
Deliver a fax copy.
This will allow you to receive attached faxmail document(s). Faxmail documents can be delivered to any fax machine of your choice as long as out
calling is authorized. You can also have faxmail messages automatically
delivered to the fax machine of your choice.
Note: After you enter your password, if “Autoplay of New Messages”is enabled and
you have new messages the SVMi-8/SVMi-16E will begin to play them automatically. A subscriber can control this feature. From the Subscriber Services Menu [6]
[5] toggles “Autoplay of New Messages” ON/OFF.
SUBSCRIBER SERVICES MENU
PERSONAL SERVICES
1 or 3
LISTEN TO YOUR MESSAGES
If there are new messages in your mailbox your [VMMSG] key will be lit. Call the
SVMi-8/SVMi-16E by pressing this key, and when prompted enter your password.
You will then be at the Subscriber Services Menu. Select [1] to listen to new messages or [3] to listen to saved messages.
PLAY MENU OPTIONS
6
Forward the message and saves a copy.
The subscriber can be selected by dialing their mailbox number (nnn),
using the directory service (#) or you may also add comments and leave it
as a memo to yourself (##).
The following is a list of all the options available in the Subscriber Main Menu.
1
LISTENING TO NEW MESSAGES
11
GROUP NEW MESSAGES
2
RECORD AND SEND A MESSAGE
3
LISTENING TO OLD MESSAGES
7
Rewind the message 5 seconds.
33
GROUP OLD MESSAGES
77
Change playback volume of the recording.
4
ACCESS MANAGER
5
PERSONAL GREETINGS
6
MAILBOX ADMINISTRATION
8
PAUSE / RESUME
76
The Send and Copy Service (option 6) allows a user to send copies of a message to multiple recipients easily. A different introduction message may be
left for each recipient.
There are two levels of volume during playback. Dialing this code will toggle between the two levels.
8
Pause or resume during message playback.
9
Fast forward the message 5 seconds.
77
99
Change playback speed of the recording.
There are two levels of speed during playback. Dialing this code will toggle
between the two speeds.
0
b) Record your message at the tone. After recording the message, you will hear
the Send Menu with the following functions:
1
2
3
4
5
6
#
Play options.
Pressing this key will play all the menu options available to you from this
point.
Review
Continue Recording
Discard and Re-Record
Set Message Attributes (Delivery Options)
Schedule Future Delivery
Save and Send then Send a Copy to Someone Else
Save and Send the Recording
00
Hear the time and date, and sender's information of the message you just
heard. Sender information is not available on outside calls.
#
Move to the next message. This does not Save or Discard the current message - it is retained as new.
Setting Message Attributes
##
Scan. Plays first 7 seconds of a message then skips to next message. This is
similar to the scan button on a radio. It will allow you to find a specific message quickly. To stop scanning press [1].
If after recording a message you select [4] you can set up any combination of the
following delivery options:
Cancel and return to previous menu.
1
2
3
4
5
11 or 33
GROUP NEW OR OLD MESSAGES
Messages can be grouped as either Reminders, press [3] or Messages from a specific sender, press [9].
Additionally you can press [#] and hear a summary of your mailbox contents:
a)
b)
c)
d)
e)
f)
Number of messages
Number of reminders
Number of urgent messages
Number of messages needing a callback
Number of private messages
Number of fax messages
Urgent Delivery
Return Receipt Requested
Request a Call Back
Private Delivery
Reply Required
Exit
Scheduling Future Delivery
If after recording a message you select [5] to schedule future delivery, you will be
able to set message attributes and set this message as:
#
1
2
3
4
5
Immediate Delivery
Next Few Hours
End of Current Business Day (based on your Availability Schedule)
Beginning of Next Business Day (based on your Availability Schedule)
A Coming Day of the Week
Specific Day / Time
Exit
2
4
RECORD AND SEND A MESSAGE
ACCESS MANAGER
This option is used to send a message to another subscriber.The steps are simple:
The Access Manager allows the subscriber to set a number of options for when,
where and how, and/or if the SVMi-8/SVMi-16E contacts you when a caller dials
your extension number. All of the options are toggled on/off based on their current status when you access them.
a)
78
Enter the recipient’s mailbox number, or if this is not known enter [#] to use
the system directory.
79
Note: ALL Access Manager options MUST be individually allowed by the System
Administrator for each Subscriber. They are:
1
Follow Me
Allows the subscriber to enter an alternate location and set how long the new
destination (Designated Location) will be active. This number may be an
internal or external number. This is useful if you are frequently traveling or
changing the number where you can be reached.
When Follow Me is activated, the transfer will be supervised and confirmed.
This means that if the call is not answered or if rejected by the Subscriber at
the designated location it will be recalled to the Subscriber’s mailbox.
3
Call Forwarding
Unlike Follow Me where the subscriber wants to take their calls at an alternate location this feature allows the subscriber to pass control of his calls to
another Subscriber. The “Forwarded To” Subscriber will now be in control of
the caller and the caller will NOT return to originating Subscriber’s Mailbox. If
the “Forwarded To” Subscriber does not answer the caller it will now follow
what ever the “Forwarded To” Subscriber has set up for their call conditions.
The Caller will hear “Forwarding to”“{Subscriber Name}” before actually being
forwarded.
5
Call Screening
If this is turned on, the caller will be asked their name and the SVMi-8/SVMi16E will play this name to you before the transfer, giving you an option to
accept or reject the call.
6
Find Me
Find Me, when enabled, will attempt to locate the subscriber by calling a list
of preprogrammed phone numbers. The stored phone numbers are entered
in 'Personal Services' [#][2] (if allowed by the Administrator). The stored telephone number list can contain up to 9 preprogrammed telephone numbers.
The Find Me feature only use the first five.
7
Night Intercept
This feature is dependent on your weekly availability schedule, which is
entered in 'Personal Services' [#][3] (if allowed by the Administrator). When
Night Intercept is active the SVMi-8/SVMi-16E will first ring your extension
80
Note: This does NOT use the Day and Night schedules of the phone system. It
is solely controlled by the Subscriber’s Availability Schedule.
8
Pause / Resume
Exit from Access Manager
0
Play All Options
#
Play Access Coverage
This feature is useful for finding out how you current access settings are set.
It will also tell you what greetings will play under each of the call conditions
you have setup.
Call Blocking
When this feature is active, callers will not be transferred to your extension,
they will hear your 'blocked' greeting (if recorded) and will go directly to your
mailbox if they do not select any or are not offered any other options.
4
then play your primary, No Answer greeting during the day (when you are
available) and will NOT ring your extension but simply play your Night greeting during the night (when you are not available).
5
PERSONAL GREETINGS
The options available in this menu will be determined by your System
Administrator, and not all of them may be available to you. In the simplest systems, only a mailbox greeting will be available, additional greetings may be accessible in more complex systems.
Your Personal Greeting will be played every time someone dials your extension
and you do not answer.
You may record up to 9 Personal Greetings, and you may assign any one of them
to be active. There are several different 'Call Coverage' conditions to which you
may assign any of your 9 greetings. The Call Coverage Conditions are: No-Answer,
Busy, and Do Not Disturb (or Forwarded All). This will allow different greetings to
play depending on the type of call forward that you have set, or the condition of
your telephone.
The Call Coverage conditions that you can assign specific greetings to are selected by the following digits:
1
Primary/No Answer Greeting
Used when in your office, away from your desk or during the time period you
are scheduled available. If this is the only Personal Greeting you record, it will
play for all call coverage conditions.
This option is available only if the Administrator has assigned you the 'Basic
Greeting' feature.
81
Example:“Hi this is John Smith. I'm sorry I am not available to answer your call.
If someone else can help you, please enter the extension number now. Or, to
leave me a message, press 1.”
2
6
Select a greeting number to edit and follow the instructions to record your
greeting. When you are done recording your greeting, you will be able to listen to the greeting you recorded, save the greeting you recorded and return
to the previous menu, record the greeting again, or exit without saving the
greeting.
Busy Greeting
Played to a caller when you are already talking to someone on your extension
or the telephone at your Designated Location.
This option is available only if the Administrator has assigned you the 'Busy
Greeting' feature.
Note: If you record only the greeting assigned to the No-Answer Call
Coverage Condition, then that greeting will play to callers for all Call Coverage
Conditions (No-Answer, Busy, Blocked, Night, and Rejected Caller). In this case,
the salutation part of the greeting should be very general.
Example:“Hi, this is John Smith. I'm on another line right now. If someone else
can help you, please enter the extension number now. Or, to leave a message,
press 1.”
3
Call Blocking Greeting
7
This option is available only if the Administrator has assigned you the 'Call
Blocking' feature.
This option is available only if the Administrator has assigned you the
'Mailbox Greeting Option' feature.
Example: “Hi, this is John Smith. Sorry I missed your call, but I'm going to be
out of the office for the next few hours. If someone else can help you, please
enter the extension number now. Or, to leave me a message, press 1.”
Example: “Hi, this is John Smith. Please leave me a message, I will call you as
soon as I can.”
Night Greeting
Note: This greeting will only play if none of the 5 personal greetings has
played to the caller. A common usage for this Greeting is when another
Subscriber is talking with a caller and uses the VT key on their phone to transfer the caller directly to your Mailbox.
Used during the time period you are scheduled UNAVAILABLE, usually after
business hours during the evening and at night.
This option is available only if the Administrator has assigned you the
'Scheduling' feature.
Example:“Hi, this is John Smith. I've left the office for the evening. If you would
like to try someone else, please enter the extension number now. Or, to leave
me a message, press 1.”
5
6
Call Screening Greeting
MAILBOX ADMINISTRATION
Used while Call Screening is enabled, and you REJECT a caller after listening
to the caller's record name.
The Mailbox Administration menu is used to turn on and off your pager notification, message alert options and other message control features.
This option is available only if the Administrator has assigned you the 'Call
Screening' feature.
1
Example:“Hi, this is John Smith. I'm sorry, but I am not available to speak with
you at this time. If someone else can help you, please enter the extension
number now. Or, to leave me a message, press 1.”
82
Edit Mailbox Greeting
Used whenever a caller reaches your mailbox or if you have not recorded any
of the Call Coverage greetings. The way a caller is transferred to your mailbox
greeting directly, is by another subscriber transferring the caller to your mailbox using the VT (VoiceMail Transfer) key.
Used while Call Blocking is enabled in your Access Manager or if your phone
is forwarded ALL or DND.
4
Edit Personal Greetings
You may also edit/record each one of the greetings (1-9) at any time.
Message Alert
When this function is activated, the SVMi-8/SVMi-16E will call any outside or
inside telephone number, after each message is left in your voice mailbox.
To hear your message at the remote location when the SVMi-8/SVMi-16E calls
you, after you pick up the telephone and answer you will be instructed that
there is a message and to enter your password. Simply enter your password
and you will now be logged in.
83
Setting Up Message Alert:
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [1] for Message Alert.
■
There are 4 options available to you:
This useful feature will allow you to cancel any messages that have NOT yet
been picked up by the recipient.
5
Press [2] to set the schedule when you would like to be notified.
If this option is enabled, after you enter your password correctly any new
messages will immediately begin to play. To enable (or if already enabled
toggle and disable) this feature:
Press [3] to be notified on urgent messages only.
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [4] to set the destination phone number.
■
Press [5] to Set Auto Play of New Messages.
Press [1] to toggle message alert on and off.
2
Auto Play New Messages
Pager Notification
6
When this function is activated, the SVMi-8/SVMi-16E will call your beeper
service and notify you after each message is left in your voice mailbox.
Auto Play Message Information
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [2] for pager notification.
If this option is enabled, the date, time and sender’s name will be played
automatically before each message. If this is disabled, the information must
be requested manually by pressing ‘00’. To enable (or if already enabled toggle and disable) this feature:
■
There are 4 options available to you:
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [1] to toggle pager notification on and off.
■
Press [6] to Set Auto Play of Message Information.
Press [2] to set the schedule when you would like to be paged.
Press [3] to be notified on urgent messages only.
9
Press [4] to set the pager phone number.
3
Undelete
When this function is activated, the SVMi-8/SVMi-16E will allow you to
undelete any messages that you have recently deleted (up to the programmed Daily Maintenance Time, which is set to 3 a.m. by Default the following morning).
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [3] for Deleted Messages.
Deleted voice mail messages are temporarily stored in memory until 3 a.m.
the following day. Select this option to recover ("undelete") previously deleted messages, during this period of time.
4
Undelivered Retrieval
MESSAGE BROADCAST
This option will only be available if it has been allowed by the System
Administrator.
Broadcast to All Mailboxes
If you have been designated as a Subscriber Administrator, you may send a
message to ALL mailboxes in the system.
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [9] for Broadcast Messages.
This option will only be available if your mailbox has been assigned
Subscriber Administration privileges.
When this function is activated, the SVMi-8/SVMi-16E will allow you to recall
any messages you have sent that have NOT yet been picked up by the recipient.
84
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [4] for Undelivered Messages.
85
PERSONAL ADMINISTRATION SETTINGS
#
PERSONAL SERVICES
This menu allows you to make changes to basic setup settings, that are rarely
changed. Use these when you initially set up your personal Subscriber settings.
You probably will not need to change them after that.
The Personal Administration Menu is used to set your password and record your
name. Many of these features must be allowed by the System Administrator.
1
1
Workload Management
Allows you to access to all reminders, both Active and Pending. If authorized
you can group your reminders as Commitments, Follow-Ups or Tasks for better organization. The system will flag each reminder as Active or Pending
(pending means scheduled for future delivery).
2
2
Stored Numbers
5
3
Place a Direct Call
The current password will be played and you will have the chance to
change it.
Recording your Name
■
From the Subscriber Services Menu press [#][7][2].
■
The current name will be played and you will have the chance to change
it.
Entering your Directory Name
■
From the Subscriber Services Menu press [#][7][3].
■
The current Directory Name will be played as a string of digits that are
equal to your name spelled out on your telephone keypad. Follow the
instructions to enter a new name.You will be prompted to enter your last
name and then your first name.
This must be done in order for the directory feature to work correctly.
Note: It is possible that if you do not record your name (described above)
and/or enter your Directory Name, you will not be included in the Dial by
Name Directory.
Personal Administration
This area is used during the initial set up of your Subscriber Settings (see next
section).
■
Use this option to enter your Directory Name.Your Directory Name is used by
callers to find you if they do not know your extension number.
Allows you to place a direct call out of the SVMi-8/SVMi-16E from anywhere.
You may either dial the number or dial a single digit 1-5 that corresponds to
a stored number (See Personal Services, 2 - Stored Numbers). This feature
must be authorized by the System Administrator and can be limited or
opened to internal, local, and long distance calls.
7
From the Subscriber Services Menu press [#][7][1].
Note: It is possible that if you do not record your name and/or enter your
Directory Name (described below), you will not be included in the Dial by
Name Directory.
Schedule Availability
Allows you to enter a weekly availability schedule for use with Night Personal
Greeting and the Auto Night Intercept feature. Follow the spoken directions
to enter the days of the week and times you are generally available to talk to
your callers. All other times you will be considered unavailable.
■
Use this option to record your name. Your recorded name is played in several
different situations. It is important to record your name for proper operation
of the SVMi-8/SVMi-16E system.
Allows you to enter up to 9 stored phone numbers. The first five of these are
used in the 'Find Me' feature, but any of them (1-9) can be easily dialed using
only one digit followed by the pound key, to be used by many other features
from within your subscriber space. (ie: “Follow Me, “Message Alert”, “Pager
Alert”, and “Direct Call”).
3
Setting your Password
4
Extended Prompting
Use this option to drastically reduce the number of prompts played in the
subscriber interface (mailbox prompts). Change this setting only if you are
very familiar with the user operation of the SVMi-8/SVMi-16E.
86
87
Note: Remember if you know what digits to press, you can enter them at any
time you do not have to wait to be prompted. This feature can be toggled
on/off at anytime. Also if it is off you will be prompted within each subscriber
menu to press zero for more options. This enables you to still be able to find
out what to do if you were to get lost and extended prompting was disabled.
KEYSET USER FEATURES
The following options are available if you have a display keyset.They require setup
by the System Administrator.
Message Waiting Lights
When new messages are left in your mailbox, the voice mail message light on your
keyset will flash. Press this flashing key [VMMSG] and follow the prompts to
retrieve messages.This key may be pressed at any time to log into your Subscriber
Main Menu.
AME Password
If your keyset has AME PASSWORD (MMC 110) set to YES, you must enter your
station password to listen to messages being left. This will prevent unauthorized
people from listening to messages being left for you.
If the password option is turned on, while a message is being left, press the flashing AME indicator and enter your station password (not your SVMi-8/SVMi-16E
password). You will then hear the message being left.
Call Record
If you have a call record button assigned to your phone, you may press it at any
time, to record the conversation in progress. If you have a display keyset, you will
also have the soft key options to pause and time the message.
Answer Machine Emulation
If you have an Answer Machine Emulation key programmed on your keyset, you
can use it to monitor calls going to your voice mail, and optionally answer them.
The operation of this feature is similar to screening a call on a home answering
machine.
Your keyset must be set to forward on no answer to voice mail. After ringing your
station the caller will be connected to your voice mail and hear your personal
greeting before leaving a message. During this time you will be monitoring the
connection between the caller and your voice mail box. At this time you will only
be monitoring the call, you can not talk to the other party until you answer. You
may pick up the call at any time or ignore it.
To activate this feature press the AME button. The associated indicator will be lit
steady. Press again to turn off. If this key is pressed while a station is ringing (during forward no answer), the feature will be turned on for the current call only.
While the caller is leaving a message or ringing you may:
■
Press [#] to immediately put the caller in your voice mailbox and monitor it.
■
Press [ ] to immediately disconnect your station. The caller continues to
leave a message normally.
■
Pick up the handset and monitor privately.
■
Press ANS / RLS to answer the call (using the handset or speaker).
88
89
PERSONAL SPEED DIAL NUMBERS
SHORTCUTS
Calling
CODE
NAME
TELEPHONE NUMBER
Calling a station that is busy or does not answer you can press [#] to immediately
send the call to the called parties mailbox.
00
_________________________
_________________________
Being Called
01
_________________________
_________________________
If your phone rings and you want to send the caller directly to your mailbox, simply press [#].
02
_________________________
_________________________
03
_________________________
_________________________
Direct Messaging
04
_________________________
_________________________
[#] + DSS To make it easy to leave messages for others in your office without having to dial their extension number first, keyset users may simply dial [#] plus a
mailbox (extension) number and leave a message directly. If you dial a busy
extension press [#] to connect directly with the mailbox.
05
_________________________
_________________________
06
_________________________
_________________________
07
_________________________
_________________________
Self Memo (Reminder)
08
_________________________
_________________________
Pressing [##] will leave a message in your own mailbox. This is useful to remind
yourself of things to do now or in the future. Messages can be sent with future
delivery so you can have the system call you when items become due.
09
_________________________
_________________________
10
_________________________
_________________________
11
_________________________
_________________________
INTERACTIVE DISPLAYS
12
_________________________
_________________________
Display keyset users have the added advantage of using the soft keys and displays
to play, save, delete, reply, call, forward, rewind, pause, fast forward, change the volume, get message information, or help.
13
_________________________
_________________________
14
_________________________
_________________________
15
_________________________
_________________________
16
_________________________
_________________________
17
_________________________
_________________________
18
_________________________
_________________________
19
_________________________
_________________________
20
_________________________
_________________________
21
_________________________
_________________________
22
_________________________
_________________________
23
_________________________
_________________________
24
_________________________
_________________________
Viewing Mailbox Contents
If you have new messages, in addition to the Terminal Status Indicator (TSI) you
will be able to use the keyset displays and soft keys to communicate with the
SVMi-8/SVMi-16E.
90
91
PERSONAL SPEED DIAL NUMBERS
CODE
NAME
TELEPHONE NUMBER
25
_________________________
_________________________
26
_________________________
_________________________
27
_________________________
_________________________
28
_________________________
_________________________
29
_________________________
_________________________
30
_________________________
_________________________
31
_________________________
_________________________
32
_________________________
_________________________
33
_________________________
_________________________
34
_________________________
_________________________
35
_________________________
_________________________
36
_________________________
_________________________
37
_________________________
_________________________
38
_________________________
_________________________
39
_________________________
_________________________
40
_________________________
_________________________
41
_________________________
_________________________
42
_________________________
_________________________
43
_________________________
_________________________
44
_________________________
_________________________
45
_________________________
_________________________
46
_________________________
_________________________
47
_________________________
_________________________
48
_________________________
_________________________
49
_________________________
_________________________
92