- Computers & electronics
- Telecom & navigation
- GPS receiver modules
- Satellite Communication
- TK102-2
- User manual
Satellite Communication TK102-2 User manual
Add to my manuals14 Pages
Satellite Communication TK102-2: Stay connected and secure with real-time location tracking, SOS emergency alerts, and remote monitoring capabilities. Ideal for personal safety, fleet management, and asset tracking.
advertisement
GPS
Portable
Tracker
USER MANUAL
V6.18
Model No.: TK102
Updated on 10 th
.July.2010
Contents
1 Summary
2 Application
3 Hardware Description
4 For Your Safe
5. Device Parameter
6 Getting Started
6.1 Hardware and Accessories
6.2 Light and Button Functionality
6.3 Installation
7 SMS Command
7.1 Basic SMS Commands
7.1.1 Position Report
7.1.2 Set Interval for Automatic Timed Report
7.1.3 Stop Automatic Timed Report
7.2 GPRS Setting by SMS
7.2.1 Set ID for TK102
7.2.2 Set APN
7.2.3 Set IP Address and Port
7.2.4 Set Time Interval for Sending GPRS Packet
7.2.5 Enable GPRS Tracking Function
8 Tracking on Map
9 Troubleshooting
10 SMS Command List
5
8
8
8
7
7
7
7
5
5
6
6
7
8
8
8
9
10
3
4
3
3
11-14
- 2 -
1 Summary
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPR
2 Applications z
Vehicle rental / Fleet management etc z Protect child / the old / the disabled / pet etc z Provide peace-of-mind for businessmen z Track criminals secretly
3 Hardware Description
3.1 Front face 3.2 Rear face
3.3 Side face
USB Port for firmware upgrade or power charging
“SOS” buttons for 3s for emergent help.
Indicator for GSM &
GPS signals
Turn on / off the unit here.
- 3 -
3.4 Bottom face
GSM/GPRS antenna is inside
Microphone
3.5 Interior
Put SIM card here.
Back up battery
4 For Your Safety
Read these simple guidelines. Not following them may be dangerous or illegal. Read the full user manual for more information.
Proper Connection - When connecting with other device, read carefully its manual so as to carry out correct installation.
Do not connect it to other incompatible devices.
Qualified Accessories - Use original parts, qualified batteries and peripheral equipments to avoid damage to TK102
Safe Driving - Drivers should not operate this product while driving.
Qualified Service - Only qualified personnel can install or repair TK102.
Water Resistance – TK102 is not water resistant. Keep it dry. Install it inside the vehicle or use waterproof bag if necessary.
Confidential Phone Number - For safety reason, do not tell other people the SIM card number of your TK102 without taking precautions of security settings.
- 4 -
5 TK102 Parameters
Power Supply +3.4V - +5V / 0.1A
Backup Battery
Dimension
850mAh Li-ion battery
64mm x 46mm x 17mm(1.8”*2.5”*0.65”)
Weight 50g
Operating temperature -20° to 55° C
Humidity
Frequency
5% to 95% Non-condensing
GSM 900/1800/1900Mhz or GSM 850/900/1800/1900Mhz
GPS Module
GPS Sensitivity
GPS Frequency
C/A Code latest GPS SIRF-Star III chipset
-158Db
L1, 1575.42 MHz
1.023 MHz chip rate
Channels
Position Accuracy
Velocity Accuracy
Time Accuracy
Default datum
Reacquisition
Hot start
20 channel all-in-view tracking
10 meters, 2D RMS
0.1 m/s
1 us synchronized to GPS time
WGS-84
0.1 sec., average
1 sec., average
Warm start
Cold start
Altitude Limit
Velocity Limit
LED
Flash Memory
Interface
38 sec., average
42 sec., average
18,000 meters (60,000 feet) max.
515 meters/second (1000 knots) max.
2 LED lights to show GPS/GSM working status.
8MB (Optional)
1 digital input for Ignition detection (Optional)
6 Getting Started
This section will describe how to set up your TK102
6.1 Hardware Features
TK102 includes:
• TK102 Main Unit
•USB Cable
•User Manual
• Wall Charger
• 2 Back up Li-ion battery
• CD including
- User Manual
- Other document or software if required
- 5 -
6.2 Light and Button Functionality
Blue LED (GPS light) - indicating GPS status
On
Flashing ( every 0.1 second)
Flashing (on for 0.1 second and off for 2.9 seconds)
Flashing (on for 1 second and off for 2 seconds)
Green LED (GSM light) - indicating GSM status
On
Flashing ( every 0.1 second)
Flashing (on for 0.1 second and off for 2.9 seconds)
Flashing (on for 1 second and off for 2 seconds)
One or more inputs are active
The unit is being Initialized
TK102 has a GPS fix
TK102 has no GPS fix
One call is coming in/ one call is being made
The unit is being Initialized
TK102 is connected to the GSM network
TK102 is not connected to the GSM network
SOS Button
6.3 Installation
Press it to send SMS alert
Read this manual before using your TK102 and check if all parts are included in the packaging box.
Ensure that your TK102 has a working SIM installed.
- Check that the SIM has not run out of credit (test the SIM in a phone to make sure it can send and receive SMS)
- Check that the SIM Lock code is turned off
- If you require the function of sending an SMS location report to the authorized phone number when it makes a call to the TK102, please make sure the SIM installed supports displaying caller ID.
- Insert the SIM card by sliding it into the card slot with the chip module facing to the connectors on PCB.
- Put back The battery and close the cover
- Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first use. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery will support around 48 hours use on end. After first use, the battery can be charged fully in 3-5hours.
Cautions: a: For it’s Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently and keep it off fire. b: Please charge the battery in time to keep it working normally.
Mini USB Port
Connect the tracker with computer by USB cable for configuration and reading stored waypoints data. You need to install the driver - PL-2303 Driver Installer - for using the USB cable.
Refer to <GPS Tracker Parameter Editor> for configuration and <GPSLog User Guide> for reading stored waypoints.
- 6 -
7 SMS Command
TK102 will only accept commands from a user with the correct password. Commands with wrong password are ignored. The default password is 000000.
7.1 Basic SMS Commands
7.1.1 Position Report
To know the location of your TK102, send an SMS or make a telephone call directly to TK102 and it will report its location by SMS.
Command: W<password>,<000>
Notes: The default password is 000000.
Example:
SMS sent: W000000,000
SMS received:
Latitude = 22 32 36.63N Longitude = 114 04 57.37E, Speed = 2.6854Km/h, 2008-12-24,01:50
To get TK102’s position by another easier way:
(a) Call TK102 using your mobile phone.
(b) After listening to the ring for 10 - 20 seconds, hang up the phone.
(c) Then after 20 second, your mobile phone will receive a position SMS.
7.1.2 Set Interval for Automatic Timed Report
Description: Automatic timed reports will be sent to your mobile phone according to the time interval you set.
Command: W<password>,002,XXX
Notes: XXX is the interval in minute. If XXX=000 it will stop tracking
Example:
SMS sent: W000000,002,005
SMS received: Set Timer Ok/005
TK102 will then report its location by SMS every 5 minutes.
7.1.3 Stop Automatic Timed Report
Description: Automatic timed reports will stop once TK102 receives stop command.
Command: W<password>,002,000
Example:
SMS sent: W000000,002,000
SMS received: Set Timer Ok/000
TK102 will stop automatic timed report
For more detailed SMS commands please go to Chapter 10 - SMS Command List
- 7 -
7.2 GPRS Settings by SMS
Tracking via GPRS, you should set IP, Port and APN for TK102.
Ensure that your SIM card in TK102 supports GPRS connection prior to setting.
7.2.1 Set ID for TK102
Command: W<password>,010,ID
Note: Tracker ID must not over 14 digits.
Example: W000000,010,123456789
TK102 will then reply with an SMS (‘Set SIM Ok/123456789’) to confirm this setting.
7.2.2 Set APN
Command: W<password>,011,APN,APN Name,APN Password
Note: If no APN name and password required, input APN only.
Example: W000000,011,CMNET
TK102 will reply with an SMS (like ‘Set APN Ok/CMNET’) to confirm this setting.
7.2.3 Set IP Address and Port
Command: W<password>,012,IP,PORT
Example: W000000,012,202.116.11.12,8000
TK102 will then reply an SMS (‘Set IP Ok /202.116.11.12,8000’) to confirm this setting.
7.2.4 Set Time Interval for Sending GPRS Packet
Command: W<password>,014,time interval(in unit of 10 seconds)
Example: W000000,014,00003
TK102 will send GPRS packet every 30 seconds
7.2.5 Enable GPRS Tracking Function
Command: W<password>,013,X
X=0, to turn off GPRS tracking function (default);
X=1, to set TCP
X=2, to set UDP
Example: W000000,013,1
TK102 will reply with an SMS to confirm this setting.
For more information regarding of bulk configuration by USB cable please refer to < GPS Tracker Parameter
Editor>.
For more information regarding GPRS settings please refer to <GPRS Communication Protocol >.
- 8 -
8 Tracking on Map
Download Google Earth from http://earth.google.com/
Start the Google Earth (For more information about Google Earth please refer to http://earth.google.com/) as the following picture shows:
Input the latitude and longitude that you receive from the tracker by SMS and click the search button. Google Earth will display the location for you.
Example:
When you receive:
Latitude = 22 32 40.05N
Longitude = 114 04 57.74E
Type as the following picture shows:
(Note: you should input the latitude and longitude as: 22 32 40.05N 114 04 57.74E)
Now you can find the location of your tracker:
- 9 -
Or you can start the Internet Explorer and connect to http://maps.google.com for displaying the location.
Or you can use local map software on PDA or car navigation device to input the coordinates.
9 Troubleshooting
Problem: Unit will not turn on
Resolution:
Recharge battery
Possible Cause:
Battery needs charging
Problem: Unit will not respond to SMS
Possible Cause:
GSM Network is slow
Unit is sleeping
Wrong password in your SMS or wrong SMS format
The SIM in TK102 has run out of credit
No SIM card
SIM has PIN code set
SIM is warped or damaged
Roaming not enabled
Resolution:
Wait for SMS. Some GSM networks slow down during peak time or when they have equipment problems.
Cancel sleeping mode
Write correct password or SMS format
Replace or top up the SIM card
Insert working SIM card. Check in phone that the SIM can send SMS message.
Check in phone that the SIM can send SMS message. Replace SIM card if needed.
Remove PIN code by inserting SIM in you phone and deleting the code.
Inspect SIM, clean the contacts. If re-inserting does not help try another to see if it will work.
If you are in a different country your SIM account must have roaming enabled.
Problem: SMS received starts with ‘Last…’
Possible Cause:
TK102 is in an inner place
Battery is low
Resolution:
Wait for the target to come out
Recharge the unit and the GPS will start working.
- 10 -
10 SMS Command List
(Remarks: ****** is user’s password, and the default password is 000000)
Description
Get current location
Command
W******,000
Remarks
Get current location of TK102
Change user’s password W******,001,######
Set interval for automatic W******,002,XXX timed report
Set preset phone number for W******,003,F,P,T
SOS button
Set low power alert
When TK102 voltage is lower
W******,004,X than the preset value, it will send one low power alert to the SOS preset number.
Set over speed alert
When TK102 speeds higher
W******,005,XX than the preset value, it will send an SMS to the SOS preset number.
Set Geo-fence alert W******,006,XX
When the TK102 moves out of preset scope, it will send one
Geo-fence SMS to the SOS preset number.
****** is old password
###### is new password
XXX is the interval in minute. If XXX=000 it will stop tracking
F=0, to turn off this function;
F=1, to send SMS;
As SOS button is linked to IN1, P=1.
T: Preset phone number. Max 16 digits
X (voltage preset value)
=0 , to turn off this function
=1, <3.3V send SMS alert
=2 , <3.4V send SMS alert
=3 , <3.5V send SMS alert (default )
=4 , <3.6V send SMS alert
=5 , <3.7V send SMS alert
XX (the preset value of speed)
=00 , to turn off this function
=[01, 20] (unit: 10Km/h)
For example, W000000,005,08, it will sent alert when it is over 80Km/h
XX ( preset distance to original place )
=00, close
=01, 30m
=02, 50m
=03, 100m
=04, 200m
=05, 300m
=06, 500m
=07, 1000m
=08, 2000m
- 11 -
Extend Settings W******,008,ABCDEFG### A=0, turn off the function of sending an
SMS location report to the authorized phone number when it makes a call to
TK102.
A=1, turn on the function of sending an
SMS location report to the authorized phone number when it makes a call to
TK102.
B=0, location data of NMEA 0183
GPRMC will be interpreted into normal text for easy reading.
For example:
Longitude = 114 degree - 04 cent -57.74 second
Latitude = 22 degree -32 cent -40.05 second
B=1, location data complies with NMEA
0183 GPRMC protocol.
For example:
$GPRMC,072414.000,V,3114.3763,N,12
131.3255,E,0.00,0.00,050805,*00
C=0, turn off the function to automatically hang up an incoming call.
C=1, turn on the function to automatically hang up an incoming call after 4 - 5 rings.
D=0, Turn off the function of sending an
SMS when TK102 is turned on.
D=1, Turn on the function of sending an
SMS to SOS number when TK102 is turned on.
E=0, reserved
E=1, TK102 shuts down automatically when the power voltage lower than 3V.
F=0, Turn off the alert when TK102 enters
GPS blind area.
F=1, Turn on the alert when TK102 enters
GPS blind area. SMS is to be sent to SOS number
G=0, LED light works normally
G=1, LED light stops flashing when TK102 working.
### is the ending character
(default value is: ABCDEFG=1000100 )
- 12 -
Presetting by SMS for GPRS tracking (Ensure that your SIM card supports GPRS connection prior to setting)
Set ID for TK102
Set APN
W******,010,ID
W******,011,APN,APNName,APN
Password
Tracker ID must not over 14 digits.
If no APN name and password required, just insert APN only;
APN defaulted as ‘CMNET’;
APN + APN name + password not over 39 characters.
Set IP Address and Port W******,012,IP, Port
Function
Set Time Interval for Sending
GPRS Packet
W******,014,XXXXX
IP: xxx.xxx.xxx.xxx Port: [1,65534]
X=0, close GPRS (default);
X=1, enable TCP
X=2, enable UDP
XXXXX should be in five digitals and in unit of 10 seconds.
XXXXX=00000, to close this function;
XXXXX=00001~65535, time interval for sending GPRS packet and in unit of 10 seconds.
X should be from 0 to 65535, the Value is Set Distance Interval for W******,045,X
Sending GPRS packet Meter
X=0, to close this function
For more information regarding GPRS settings please refer to <GPRS Communication Protocol>
Set power saving mode W******,026,XX when TK102 is inactive This command Optional for the TK1022
XX=00, to turn off this function
XX=01~99, to set this function. It is in unit
(In power saving mode, GPS which with Motion sensor of minute. stops working. GSM enters standby mode and stop sending out message until it is activated by an SMS or an incoming call)
Example:
If XX=10, TK102 will enter power saving mode after it is immobile for 10 minutes.
Set phone number for W******,030,T wiretapping
T is the telephone number for wiretapping and max. 16 digits
If T keep empty, change the wiretapping mode to tracking mode
Set interval for logging W******,031,X
(Note: this interval is not This command is Optional for the TK1022
X=0, to turn off this function
X=[1, 65535] to set interval in second. relevant to the interval of which with the 8MB memory continuous tracking)
For example, W000000,031,60, TK102 will store location data every 60 seconds.
Set time zone difference W******,032,T T=0, to turn off this function
T=[1, 65535] to set time difference in minute to GMT. Default value is GMT
For those ahead of GMT, just input the time difference in minute directly. For example, W000000,032,120
‘-‘is required for those behind GMT. For
- 13 -
Set character for SOS alert W******,033,1,Char message
Get SMS in goolge link W******,100 format example, W000000,032,-120.
Char is the character in SOS message and max 32 characters
The device will send the SMS report with google map link, which can open the map on the PDA or Smart phone.
- 14 -
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project