Uniden | D1780-2BT | User`s guide | Uniden D1780-2BT User`s guide

D1780-BT Series User's Guide
You will also find:
What's in the box?
D1780-BT base
with answering
system and
cordless
handset
Accessory handset
and charger
Not pictured:
xx Rechargeable
battery (BT-1025)
xx Battery cover
xx AC adapter
(PS-0034)
If you purchased
model number:
D1780-2BT
Not pictured:
xx Rechargeable
battery (BT-1025)
xx AC adapter (PS-0034)
xx Telephone cord
D1780-12BT
...
...
Battery
cover
You should
have:
1 of each
11 of each
* If the model number ends in R,
your package includes a DRX100
range extender. Refer to the
DRX100 User’s Guide for details.
• If any items are missing or damaged, contact our Customer Care Line
immediately. Never use damaged products!
• Need help? Get answers 24/7 at our website: www.uniden.com.
If You...
Contact Uniden’s...
have a question or problem
Customer Care Line*
need a replacement part or an
accessory
need special assistance due to
a disability
Phone Number
817-858-2929 or
800-297-1023
Parts Department*
800-554-3988
Accessibility Help Line
800-874-9314
(voice or TTY)
* During regular business hours, Central Standard Time; see our website for detailed business hours.
© 2012 Uniden America Corp.
Ft. Worth, Texas
Printed in Vietnam
U01U424BZB(0)
What’s in the manual?
Getting Started................................. 3
Installing Your Phone..................................3
Setting Up the CellLink™
Bluetooth™ Connection..........................4
Getting to Know Your Phone....................6
Using the Handset Menu...........................9
Using Your Phone............................ 11
Using the Phonebook................................12
Using Special Features................... 13
Off-Hook Menus..........................................13
Silent Mode...................................................15
Multihandset Features............................. 16
Chain Dialing............................................... 16
Voice Message Notification.................... 16
Using the Answering System ........ 17
Answering System Options
(Answering Setup)..................................17
Personalizing the Greeting.....................17
Accessing the Answering System.........18
Getting Your Messages.............................18
Using the System While
You're Away from Home.......................19
Important Information...................20
Solving Problems....................................... 20
Adapter and Battery Information........ 23
Compliance Information......................... 23
1-Year Limited Warranty.......................... 26
Important Safety Instructions!
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
• This unit is NOT waterproof. DO NOT expose it to rain or moisture.
• Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
• Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local codes
for possible special disposal instructions.
• Do not place the handset in any charging cradle without the battery
installed and the battery cover securely in place.
SAVE THESE INSTRUCTIONS!
CAUTION! Risk of explosion if battery is replaced by an incorrect type!
Dispose of used batteries according to the instructions. Do not open or
mutilate the battery. Disconnect the battery before shipping this product.
For more details, see the Important Information section.
2 - English
Getting Started
Installing Your Phone
Charge the Battery
1. Unpack all handsets,
battery packs,
and battery
covers. If
you need to
remove a
cover, press
in on the
notch and slide the cover down
and off.
2. Line up the battery connector
with the jack inside the handset;
the connector only fits one way.
3. Push the connector in until
it clicks into place; tug gently
on the wires to make sure the
battery is securely connected.
4. Replace the battery cover and
slide it into place.
5. Use an AC adapter to connect
the power jack on the base to a
regular indoor (120V AC) power
outlet. Connect any chargers the
same way.
6. Place a handset in the base with
the display facing forward. If
the display doesn’t light up,
reseat the handset or connect
the base to a different outlet. For
2 or more handsets, place each
handset in a charger.
##Charge all handsets
completely (about 15 hours)
before using.
Connect the Telephone Cord
Use the telephone cord to connect
the TEL LINE jack on the base to a
standard telephone wall jack.
Test the Connection
1. Pick up the handset and press
Talk . The handset sounds a dial
tone, and the display shows Talk.
––If you don't hear a dial tone or
the display says Check Tel Line,
check the connection between
the base and the phone jack.
2. Make a quick test call. (Press END/
CLEAR to hang up.)
––If you keep hearing a dial tone,
change to pulse dialing.
––If there’s a lot of noise, check
for interference (see page 21).
3. Test all handsets the same way.
If you can't get a dial tone, move
the handset closer to the base.
Changing to Pulse Dialing
Your phone uses tone dialing by
default. If your phone company uses
pulse dialing, you need to change
your phone’s dial mode.
1. On a handset, press Menu/select
and choose Global Setup.
2. Select Dial Mode then Pulse.
You’ll hear a confirmation tone.
To send DTMF tones during a call
(e.g., for an automated response
system), press * to temporarily
switch to tone dialing. When you
hang up, the phone automatically
returns to pulse dialing.
English - 3
Attaching Optional Wall Mount Bracket
You can order a wall-mount bracket from the Uniden website. Follow the
instructions that come with the bracket.
Setting Up the CellLink™ Bluetooth™ Connection
The new D1780-BT with CellLink technology can connect with mobile
phones that support the Bluetooth V2.1 handsfree profile.
• If you are not certain of the profiles supported by your Bluetooth phone
or if you have difficulty pairing your phone to the D1780-BT, see the
manual that came with your phone.
• With the CellLink feature, you can essentially treat your cellular phone
as a second line. You can use the D1780-BT handset to make and receive
calls on your cellular phone number, put cellular calls on hold, and
transfer calls to other handsets. See page 5 for more information.
• Bluetooth wireless devices have a maximum range of about 33 feet (10
m); the actual range will vary depending on local conditions (obstacles,
battery power, interference, etc.).
Pair your Bluetooth phone
Pairing “introduces” the Bluetooth device and D1780-BT and gives them
permission to connect to each other. In most cases, once you pair a phone
to the D1780-BT, these two devices connect automatically whenever they
detect each other. (If you have to manually reconnect each time, check the
Bluetooth settings on your cellular phone.) You can pair your Bluetooth
devices through the D1780-BT handset.
1. Press Menu/Select to display the handset’s main menu.
2. Select the Bluetooth Setup menu, then select the Add Cellular submenu.
The base goes into pairing mode when the handset displays Search &
select from Cellular D1780-2BT PIN: 0000.
3. On your Bluetooth phone, start a search for other Bluetooth devices.
(This process may take several seconds and it will be different for
each mobile phone. See your phone owner’s manual for detailed
instructions.)
4. Your phone should discover a device called D1780-2BT or Handsfree
device. When your phone asks if you want to pair with this device,
answer yes.
4 - English
5. If your phone prompts you for a PIN code or password to pair with the
D1780-BT, enter 0000 (four zeroes).
6. When your phone accepts the Bluetooth connection, the D1780-BT
sounds a confirmation tone. The Bluetooth device number icon on the
base and the handset display light up.
##Most cell phones automatically transfer the audio to a Bluetooth
device as soon as it pairs; if yours does not, look in your cell
phone’s Bluetooth setup for a “transfer audio” or “send audio to
device” option.
To test the connection
1. Pick up the handset from the cradle.
2. Dial the number you want to call, then press Cell on the handset. You
may not hear a dial tone or ringing, but the handset display says Talk.
3. Make sure the call connects and you can hear clearly. (When you’re
finished, press END/CLEAR to hang up.)
• The D1780-BT remembers the pairing information for your cellular;
if it loses connection with your phone for any reason (e.g., the cell
phone travels out of range, runs out of charge, etc.), the D1780-BT
can automatically reconnect the next time your phone becomes
available.
Using the D1780-BT with two Bluetooth phones
• The D1780-BT can save the pairing information for two different
Bluetooth phones, but it can only use one cellular line at any given time.
For example, if you pair the D1780-BT to two Bluetooth phones, when
you press Cell on the handset, the D1780-BT asks which phone you want
to connect to.
• If you are using the D1780-BT to talk on one Bluetooth phone, the
D1780-BT will not ring if a call comes in on another phone.
• You can set a different ring tone for each paired cell phone (see page 10).
• To pair another Bluetooth phone, just repeat the pairing procedure with
the new phone. (If the paired phone interferes when you’re pairing the
new one, just turn off Bluetooth on the paired phone until you finish
pairing the new one.)
English - 5
Getting to Know Your Phone
Parts of the Handset
Status
Earpiece
Display
PHONEBOOK
UP
MENU/SELECT
END/CLEAR
HOME/FLASH
CELL
DOWN
CID
Twelve-key
dial pad
REDIAL/PAUSE
SPEAKER
Microphone
MESSAGE/MUTE
Charging
contacts
Key (icon)
What it does
xx In standby or during a call: open the phonebook.
Phonebook
xx In the menu: go back to the previous screen.
( )
xx When entering text: move the cursor to the left.
Speaker (
) xx Switch a normal call to the speakerphone (and back).
HOME/FLASH
Down (
)
Redial/pause
Up (
)
Menu/select
6 - English
xx In standby: start a telephone call (get a dial tone).
xx During a call: switch to a waiting call.
xx In standby: decrease the ringer volume.
xx During a call: decrease the audio volume.
xx In any menu or list: move the cursor down one line.
xx In standby: open the redial list.
xx When entering a phone number: insert a 2-second pause.
xx In standby: increase the ringer volume.
xx During a call: increase the audio volume.
xx In any menu or list: move the cursor up one line.
xx In standby: open the menu.
xx In the menu or any list: select the highlighted item.
Key (icon)
END/CLEAR
Cell
CID (
)
Intercom
Message/
mute (
)
LED
Status
What it does
xx During a call: hang up.
xx In the menu or any list: exit and go to standby.
xx When entering text or numbers: erase the character at the
cursor (press & hold to erase all characters).
xx In standby: start a telephone call using a paired Bluetooth
phone.
xx While a paired phone is ringing: answer the incoming call.
xx During a CellLink call: switch to a waiting call.
xx In standby or during a call: open the Caller ID list.
xx When entering text: move the cursor to the right.
xx In standby: start an intercom call.
xx During a call: put the call on hold and start a call transfer.
xx In standby: access your answering system.
xx During a call: mute the microphone.
xx While the phone is ringing: ignore this call (mute the ringer).
What it means
xx On: the battery is charging.
xx Blinking: there are new messages.
Reading the Display
The table shows the possible
status icons and what they
mean. Since the icons appear
based on what the phone is
doing, you won't see all the
icons at the same time.
Icon
Status
icons
Current
call info
Time &
date
Answering
system
status
What it means
Bluetooth device #1 or #2.
Home phone line.
The signal from the base is acceptable.
The ringer is turned off and will not ring for new calls.
English - 7
Icon
What it means
The speakerphone is on.
Indicates you have a new voice mail.
Privacy mode is on: no other handset can join the call.
The battery is 1) full, 2) half charged, 3) getting low or 4) empty.
The handset is using ECO (power save) mode.
[Aa] [aA] Enter 1) capital or 2) lower case letters (see page 11).
Parts of the Base
FIND HS
REV
DELETE
FWD
UP
DOWN
Message
Counter
Charging
contacts
ANS ON/OFF
PLAY/STOP
Bluetooth
Device Number
Key (icon) What it does
xx In standby: page all handsets.
FinD hS
xx While playing a message: restart the message.
REV (
)
xx In the first 2 seconds of a message: play the previous message.
xx While playing a message: delete this message.
Delete ( ) xx In standby: delete all messages.
xx While playing a message: skip to the next message.
FWD (
)
xx In standby: increase the ringer volume.
Up (+)
xx While playing a message: increase the speaker volume.
xx In standby: decrease the ringer volume.
–
Down ( )
xx While playing a message: decrease the speaker volume.
Ans on/off xx In standby: turn the answering system on or off.
xx In standby: start playing messages.
Play/stop
xx While playing a message: stop playing messages.
(
)
xx When the phone is ringing: ignore this call (mute the ringer).
8 - English
Key (icon) What it does
Bluetooth
The number indicates the Bluetooth device number linked to
device
the D1780.
number
mESSAGE
cOUNTER
xx Displays the number of messages you have.
Using the Handset Menu
If you don't press any keys for about 30
seconds, the handset
Press MENU/SELECT to choose
exits the menu.
the current option.
Intercom
During a call, use
Bluetooth Setup
Phonebook to back
Add Cellular
out of the
Press
Search & Select
menu without
PHONEBOOK to
Use UP and DOWN to
go back a screen
hanging up.
from Cellular
Press MENU/SELECT to
open the menu.
OR
press END to exit
the menu.
rotate through the
options.
Intercom Menu
The Intercom menu lets you connect 2 handsets without using the phone
line. Any handset can connect to an intercom call, but only two handsets
can be in the call at one time.
Bluetooth Setup Menu
The Bluetooth Setup menu provides the following operations:
Menu Option
What it does
Add Cellular
Pairs cellular phone with base.
Privacy Setup
Determines which handsets will ring when a cellular
call comes in (default = ALL).
Download PB
Downloads the cellphone phone book to the base.
Remove Cellular
Un-pairs a cellular phone from the base.
Handset Setup Menu
You can change these settings separately for each handset.
English - 9
Menu Option
What it does
Turn on T-coil mode to reduce noise on hearing aids
equipped with a telecoil (T-coil) feature. T-coil mode
T-Coil
shortens talk time, so keep your battery fully charged.
Choose this handset's ring tone. As you highlight each
ring tone, the phone plays a sample. When you hear
Ringer Tones
the tone you want, press Menu/select.
Turn on personal ring so you can assign a special ring
tone to people in your phonebook. With Caller ID, this
Personal Ring
handset uses the assigned tone when the person calls.
Have this handset answer a call when you pick it up
AutoTalk
from the cradle (without pressing any buttons).
Have this handset answer a call when you press any
Any Key Answer
key on the 12-key dialpad.
Banner
Change the name used on the handset's display.
Handset Language Change the display language.
Key Touch Tone
Have the keypad sound a tone when you press a key.
Answering Setup Menu
Refer to page 17 for details on setting up your answering system.
Date & Time Menu
Use this menu to set the clock. Enter the date and time (MM/DD/YY and
HH/MM); select AM or PM. Use CID to move the cursor past a digit without
changing it. If you have CID service, you can set it to provide the time
(Global Setup/CID Time Setting).
Global Setup Menu
The settings on this menu affect all handsets. Only one handset at a time
can change these menu options.
Menu Option
What it does
Dial Mode
Choose tone or pulse dialing (see page 3).
Enter, edit, or delete the access number for your
Edit Voice Mail
voice mail service (see page 17.).
Edit Int’l Number
Enter, edit, or delete an international code.
Do not change this setting unless instructed to by
Set Line Mode
customer service.
10 - English
Menu Option
VMWI Reset
CID Time Setting
What it does
Reset the Voice Message Waiting Indicator (see page
17.)
Set CID Time Setting to ON or OFF to allow phone
network to automatically set cordless phone system
time.
Entering Text on Your Phone
• Use the 12-key dial pad anytime you want to enter text into your phone
(a name in the phonebook, the handset banner, etc.).
• If two letters in a row use the same key, enter the first letter; wait for the
cursor to move to the next space and enter the second letter.
To...
Press...
Phonebook.
move the cursor left
CID.
move the cursor right
END/CLEAR.
erase the character at the cursor
erase the entire entry
and hold END/CLEAR.
#.
enter a blank space
switch between upper and lower case letters
*.
0.
rotate through the punctuation and symbols
Using Your Phone
This section explains the most common functions on the phone.
Using the
Using the
earpiece
speakerphone
press Speaker.
make a call, dial the number & press HOME/FLASH.
press Speaker.
answer a call
press HOME/FLASH.
press END/CLEAR or put the handset in the
hang up
cradle.
press Message/mute while the phone is
ignore a call/mute the ringer
ringing.
switch to the speaker & back press Speaker.
mute the microphone during press Message/mute (press again to turn the
microphone back on).
a call
put a call on hold
press Intercom*.
press Speaker.
return to a call on hold
press HOME/FLASH.
To...
* After 5 minutes on hold, the call will be disconnected.
English - 11
Finding a Lost Handset
With the phone in standby, press Find HS on the base. All handsets beep for
1 minute; to cancel, press Find HS again or press any handset key.
Changing the Volume
To change the...
earpiece or speaker
volume for each handset
base speaker volume
ringer volume for each
handset or the base*
When...
Press...
you are listening to that
earpiece or speaker (playing
messages, etc.)
Up to increase
the phone is in standby
the volume.
Down to
decrease it.
* If you turn the ringer all the way down, that particular ringer turns off.
Using the Caller ID and Redial Lists
Caller ID (CID) is a service available from your telephone provider that
shows the phone number (and sometimes the caller’s name) of incoming
calls. Contact your telephone provider for more information.
Caller ID list
Redial list
xx The phone saves the information for the last 50
xx Each handset
received calls to the CID list. The NEW icon marks any
remembers the
calls received since the last time you checked the list. last 5 numbers
you dialed on it.
xx All handsets share the same CID list so only one
handset can access the list at a time.
xx Only one handset
can access its
xx In standby, handsets show how many calls came in
redial list at a time.
since the last time you checked the CID list.
To…
Press...
CID.
open the CID list
open the redial list Redial/pause.
scroll through the DOWN to scroll from newest to oldest.
lists
UP to scroll from oldest to newest.
dial the
HOME/FLASH or speaker.
highlighted
(If the number is a toll call but there is no 1 at the
number
beginning, press * to add 1 before dialing.)
close the lists
Phonebook.
For individual record options, highlight a number and press Menu/select:
Delete Entry
12 - English
Erase the number from the list.
Store Into PB
Delete All
Add the number to the phonebook. The handset prompts
you to edit the name and number and select a personal ring.
(CID list only) Erase all numbers from the list.
Using Call Waiting
• Call Waiting, a service available from your telephone provider, lets you
receive calls while you are on another call. Caller ID on Call Waiting
(CIDCW) service displays Caller ID information for a waiting call.
• If you get a Call Waiting call, the phone sounds a tone and displays
any CID information received from the waiting call. Press HOME/FLASH
to switch between the current call and the waiting call; each time you
switch, there is a short pause before you're connected to the other call.
Using the Phonebook
The phone can store up to 100 entries in its phonebook. All handsets share
the same phonebook, so only one handset can access it at a time.
To...
Press...
open/close the phonebook Phonebook.
Down to scroll through the entries from A to Z.
scroll through the entries
Up to scroll from Z to A.
jump to entries that start
the number key corresponding to the letter
with a certain letter
you want.
dial the current entry
HOME/FLASH or Speaker.
edit the current entry
Menu/select, then select Edit.
Menu/select, then select Delete. When the
delete the current entry
phone prompts you to confirm, select Yes.
Adding Phonebook Entries
With the phone in standby, open the phonebook. Press Menu/select and
select Create New. Enter a name, number, and a personal ring if desired. • Enter the phone number (up to 32 digits) exactly as you would dial it.
• If you need the phone to wait before sending the next set of digits, press
Redial/pause to insert a 2-second pause. You can insert multiple pauses,
but each one counts as a digit (you’ll see P in the display).
Downloading Cellular Phonebooks
You can download up to 700 names per cellular phonebook (1400 total) to
the phonebook.
English - 13
1. Press Menu/select and select Bluetooth Setup. Scroll to Download PB and
select it.
2. The Bluetooth icon on the LCD display will show the device number of
the downloading phonebook (for Bluetooth device #1:
.)
3. Download PB Completed displays when the download is completed.
Download PB Failed displays if the download fails.
Deleting All the Phonebook Entries
With the phone in standby, open the phonebook. Press Menu/select and
select Delete All. When the phone prompts you to confirm, select Yes.
Using Special Features
Off-Hook Menus
When you are in a call, pressing MENU/SELECT brings up special off-hook
menus:
Hold/Transfer
In a call: puts the call on hold and lets you page a
specific handset or base to transfer the call to or
page the base and all the handsets.
Call Privacy
Determines which handsets will ring when a cellular
call comes in (default = ALL).
Drop Call
In a 3-way conference call: allows you to drop one of
the outside calls and remain connected the other.
Hold/Transfer
You can put a landline call on hold and transfer it to another handset.
To...
put a landline
call on hold
take a landline
call off of hold
Press...
MENU/SELECT and select Hold/Transfer.
Home/flash.
MENU/SELECT and select Hold/Transfer from the off-hook
menus. The call is now on hold and the system prompts
transfer a call
you to select the handset (or all handsets) you want to
page. When another handset accepts the call, you will
be disconnected. Press Home/flash to rejoin the call.
cancel a transfer Home/flash to return to the call.
14 - English
To...
accept a
transferred call
Press...
END/clear to answer the page and speak to the other
handset. Then, press HOME/flash to speak to the caller.
Call Privacy
To activate call privacy mode on a call in progress, press Menu/select, then
select Call Privacy. As long as call privacy mode is on, you’ll see a in the
display, and no other handsets can join your call. Call privacy mode turns
off automatically when you hang up; you can also turn it off by pressing
Menu/select and then selecting Call Privacy again.
Drop Call
This off-hook menu selection lets you drop a call when you are in a 3-way
conference call with a landline call and a cellular call. You can select to
drop one of the outside calls.
1. From a 3-way conference call, press MENU/SELECT and select Drop Call
from the off-hook menus.
2. Select the HOME icon to drop the landline call or the CELL icon to
drop the cellular call. You will remain connected to the other call.
Intercom (Handset to Handset)
• Whenever the phone is in standby, you can make an intercom call
between handsets without using the phone line.
• You can make an intercom call from any handset, but only two handsets
can be in an intercom call at any time.
• If an outside call comes in during an intercom page, the phone cancels
the page so you can answer the incoming call.
• If an outside call comes in during an intercom call, press HOME/FLASH to
hang up the intercom call and answer the outside call.
To...
make an intercom page
cancel a page
answer a page
Press...
MENU/SELECT and select Intercom from the menus.
A list of handsets displays. Select the handset
you want to talk with, or All to page all handsets
at the same time.
End/CLEAR.
HOME/FLASH or select Intercom from the menus.
English - 15
To...
put an outside line call
on hold and make an
intercom call
end an intercom call
Press...
MENU/SELECT and select Hold/Transfer from the
off-hook menus. Select the handset you want
to talk with, or All to page all handsets at the
same time.
End/CLEAR. Both handsets return to standby.
Silent Mode
You can silence the ringers on the base and all handsets for a specific
period of time; the answering system answers any incoming calls without
playing anything through the speaker.
1. With the phone in standby, press and hold # on any handset. The phone
prompts you to select the number of hours (1 - 9 or Always On) that you
want it to stay in silent mode.
2. To confirm, press # or just wait about 5 seconds. The phone turns on the
answering system and displays Silent Mode On on each handset.
3. After the selected number of hours, the phone automatically exits silent
mode. To exit silent mode manually, press and hold # again.
##If the phone is in silent mode and you turn off the answering
system, the phone exits silent mode.
Multihandset Features
##To use the features in this section, you need at least 2 handsets.
• Your base supports a total of 12 cordless handsets: the one that came
with the base and up to 11 DCX170BT accessory handsets. Your base
also supports a total of 2 DRX100 range extenders, including any that
came with your phone.
• You must register accessory handsets to the base before using them.
(Handsets that came packaged with the base are already registered.)
• Handsets that aren’t registered display a Not Registered message.
For registration instructions, see page 23, or see the accessory handset
manual.
• If a handset was ever registered to a base, you must reset it before it can
register to a new base; seepage 23, or see the accessory handset manual.
Conference Calling
• When an outside call comes in, two handsets and one cell phone can
join in a conference call with the outside caller.
16 - English
• To join a call that’s already in progress, just press HOME/FLASH or Speaker .
• To leave the conference call, hang up normally; the other handset
remains connected to the call.
Chain Dialing
If you often have to enter a series of digits or a code number during a
call, you can save that code number to a phonebook entry and use the
phonebook to send the code number.
1. Enter the code number (up to 32 digits) into the phonebook just like
a regular phonebook entry. Be sure to enter the code number into the
phonebook exactly as you would enter it during a call.
2. When you hear the prompt that tells you to enter the number, open the
phonebook and find the entry that contains your code number.
3. Press Menu/select to send the code. If you change your mind, just close
the phonebook.
Voice Message Notification
If you subscribe to a voice mail service, your phone displays the voice mail
icon (
) when you have a new message.
After you listen to your messages, the message icon turns off. If it doesn’t,
you can reset it: With the phone in standby, open the menu and select
Global Setup; select VMWI Reset, then select Yes.
If you change voice mail providers, you can edit your voice mail number.
Open the menu and select Global Setup/Edit Voice Mail.
Using the Answering System
Answering System Options (Answering Setup)
You can set or change the answering system options from any handset. Just
open the menu and select Answering Setup. Select one of the following:
Security Code
Ring Time
Enter a 2-digit PIN so you can access your answering
system from any touch-tone phone (see page 20).
Set the number of rings (2, 4, or 6) before the system
answers. Toll Saver makes the system answer after 2 rings
if you have new messages or after 4 rings if you don't.
English - 17
Set the amount of time (1 or 4 minutes) callers have to
leave a message. Choose Announce Only if you don't
want the system to let callers to leave a message.
Have the system beep every 15 seconds when you have
Message Alert
a new message. The alert stops after you listen to all
your new messages or if you press any key on the base.
Ans. Language
Change the language of the system's voice prompts.
Turn on the call screen feature so you can hear callers as
Call Screen
they leave messages on the base speaker (see page 19).
Ans. On/Off
Turn your answering system on or off.
Record Greeting Record an outgoing message or greeting.
Greeting Options Switch greetings or delete your greeting.
Record Time
Personalizing the Greeting
Your personal outgoing message or greeting can be from 2 to 30 seconds
long. If you don’t record a greeting, the system uses a pre-recorded
greeting: Hello, no one is available to take your call. Please leave a message
after the tone.
To...
Record a
personal
greeting
Switch
between
greetings
Delete your
greeting
18 - English
Follow these steps:
1.Open the menu with the phone in standby. Select
Answering Setup, then Record Greeting.
2.Press MENU/SELECT to start recording. Wait until the system
says "Record greeting" before speaking.
3.Press Menu/Select to stop recording. The system plays back
your new greeting.
4.To keep the greeting, press End/CLEAR. To re-record it,
press Menu/select.
1.Open the menu with the phone in standby. Select
Answering Setup, then Greeting Options.
2.The system plays back the current greeting. Press Menu/
select to switch greetings.
Switch to your personal greeting, then press END/CLEAR.
Accessing the Answering System
When the phone’s in standby, you
can access the answering system from
any handset:
Press MESSAGE/MUTE to start
remote operation mode.
1:Repeat 3:Skip
4:Delete 5:Stop
• Only 1 handset can access the
system at a time.
Press a corresponding number key to
• If you do nothing for 30 seconds,
choose an operation
OR
the phone returns to standby.
END to exit remote
operation mode.
• During remote access, the phone
beeps so you know it's waiting for
the next command.
• You can press the number key shown next to each command instead of
scrolling through the screens.
Getting Your Messages
To...
From the base
From a handset
Press Play/stop.
Press Message/mute.
The system announces the number of new & old
play new
messages, then plays each new message (followed by the
messages
day and time) in the order it was received.
restart this
Wait at least 5 seconds after the message starts playing,
select 1:Repeat.
press REV.
message
replay an
Within 2 seconds after a message starts playing,
select 1:Repeat.
earlier message press REV.
skip a message Press FWD.
Select 3:Skip.
delete a
While a message is playing, press While a message is
message
Delete.
playing, select 4:Delete.
With the phone in standby,
delete all
press Delete; press Delete again to Not available.
messages
confirm.
play old
After the system plays all new messages,
select 2:Play.
press Play/stop again.
messages
stop playback Press Play/stop.
Select 5:Stop.
Screening Your Calls
You can use the answering system for call screening. While the system
takes a message, you can listen on the base speaker (if you turn on Call
English - 19
Screen) or from a handset. Only one handset can screen calls at a time. If
another handset tries to screen calls, it beeps and returns to standby.
To...
From the base
hear the caller leaving
a message
answer the call
mute the call screen
without answering*
Listen to the caller
over the speaker.
NA
Press Play/stop.
From a handset
Press Message/mute.
Press HOME/flash.
Press End/CLEAR or return
the handset to the cradle.
* If you mute the call screen, the system continues taking the message: it just
stops playing through the speaker.
Using the System While You're Away from Home
You can dial in to your answering system from any touch-tone phone.
Before you can use this feature, you must program a security code.
Programming a Security Code
With the phone in standby, open the menu; select Answering Setup, then
select Security Code. Use the number keypad to enter a two-digit security
code (01 to 99). Press Menu/select when you’re finished.
##Remember to make a note of your new security code!
Dialing In to Your System
1. Call your phone number & wait until the system answers. (If the system
is turned off, it answers after 10 rings & sounds a series of beeps.)
2. During the greeting or beeps, press 0 and immediately enter your
security code. If you enter it incorrectly 3 times, the system hangs up
and returns to standby.
3. The system announces the time, the number of messages in memory,
and a help prompt. It beeps to let you know it's waiting for a command.
4. When you hear beeping, enter a 2-digit command from the chart.
01 Repeat message
05
Stop playback
02 Play message
06
Turn the system on
03 Skip message
09
Turn the system off
04 Delete message
10
Hear help prompts
##If you don't press any keys for 15 seconds, the system hangs up
and return to standby.
20 - English
Important Information
Solving Problems
If you have any trouble with your phone, check this section first. If you
need help, call our Customer Care Line listed on the front cover.
General problems
Possible solutions
xx Check the telephone cord connection.
No handsets can make or
xx Disconnect the base AC adapter for a few
receive calls.
minutes; then reconnect it.
A handset can’t make or
xx Move the handset closer to the base.
receive calls.
xx Make sure the ringer is turned on.
A handset can make calls,
xx Make sure Silent Mode is turned off (see page
but it won’t ring.
16).
xx Charge the battery for 15-20 hours.
A handset is not working.
xx Check the battery connection.
The phone keeps ringing
xx You may have to change the line mode.
when I answer on an
Contact Customer Service for instructions.
extension.
xx Check for interference from appliances
(microwave ovens, TVs, etc.) or wireless
devices (baby monitors, WiFi equipment,
etc.). Move the handset or base away from the
There’s a lot of noise or
interference source.
static on the line
xx If you have any service that uses the phone
line, add a DSL or a telphone line filter (see
page 22).
Caller ID problems
Possible solutions
xx Let calls ring twice before answering.
No handsets display
Caller ID information.
xx Make sure your Caller ID service is active.
Caller ID displays briefly xx You may have to change the line mode.
Contact Customer Service for instructions.
and then clears.
Multi-handset problems
Possible solutions
xx Reset the handset (see page 23).
I can’t transfer calls.
Two handsets can’t talk to a caller. xx See if any handset is in Privacy Mode.
xx Move the handset closer to the base.
A handset says Unavailable.
xx See if any handset is in Privacy Mode.
English - 21
Multi-handset problems
Possible solutions
xx Reset the handset (see page 23).
I can’t register a new handset.
xx See if you have 12 registered handsets.
Answering system problems Possible solutions
xx Make sure the answering system is on.
The answering system does
xx Make sure the base is plugged in.
not work.
xx See if Record Time is set to Announce Only.
The system won't record
messages.
xx Delete messages (memory may be full).
xx See if another handset is using the system.
A handset can't access the
answering system.
xx Make sure the phone is in standby.
xx If there was a power failure, re-record
My outgoing message is gone.
your personal outgoing message.
xx Make sure call screening is turned on.
I can’t hear the base speaker.
xx Change the base speaker volume.
xx Increase the Record Time.
Messages are incomplete.
xx Delete messages (memory may be full).
The system keeps recording
xx You may have to change the line
mode. Contact Customer Service for
when I answer on an
instructions.
extension.
Installing a Line Filter or DSL Filter
A telephone line filter or DSL filter prevents services that use the phone
line from causing interference on your phone. To get a line filter, contact
your service provider or look in an electronics store.
Plug the filter into the telephone wall jack and plug the base into the filter.
Make a test call to make sure the noise is gone.
Liquid Damage
CAUTION: If the base is covered in liquid, disconnect the adapter
& phone cord from the wall before touching it.
If the liquid is only on the exterior housing of the base or handset, wipe it
off and use as normal. If you can hear liquid inside the housing:
1. Remove all compartment covers, and disconnect all cables and cords.
2. If liquid is leaking from any vent or hole, turn the phone so that vent
faces down. If not, place the largest vent face down.
3. Let dry for at least 3 days. Check for liquid inside the phone before
replacing compartment covers & reconnecting cords.
22 - English
Resetting Handsets
If you have trouble with a handset
or if you want to replace one, clear
the registration information from
the base and the handset:
1. Press & hold END/CLEAR and # at
the same time until you see the
System Reset menu.
2. If you still have the base the
handset is registered to, select
Deregister HS, then select the
handset you want to reset. If you
don’t have that base anymore,
select Base Unavailable.
3. To confirm, select Yes. The
handset displays Handset not
registered.
Registering Handsets
If you see a “not registered”
message on a handset, you must
register it to a base before using it.
1. Place the handset in the base;
the display should say Handset
Registering.
2. Wait until the display says
Registration Complete (about
30 seconds), then pick up the
handset and press HOME/FLASH.
3. If you don’t hear a dial tone or
the display says Registration
Failed, charge the battery
completely, then try again.
Adapter and Battery
Information
AC adapter
Part number
PS-0034
Input voltage
120V AC, 60 Hz
Output voltage 7.8V AC @ 450mA
xxUse only the supplied AC adapters.
xxUse the proper adapter for the base &
any chargers.
xxDo not place the unit in direct sunlight
or subject it to high temperatures.
Battery pack (with normal use)
Part number
BT-1025
Capacity
400mAh, 2.4V DC
Talk time
about 7 hours
Standby time
about 7 days
Battery life
about 1 year
xxReplace the battery when the talk or
standby time becomes noticeably reduced. For replacements, call the Parts
Department (see the front cover).
xxWhen the battery gets low, the handset
beeps and shows a low battery alert;
put the handset in the cradle for
recharging.
Rechargeable Battery Warning
xxThis equipment contains a rechargeable Nickel-Metal-Hydride (Ni-MH)
battery.
xxNickel is a chemical known to the state
of California to cause cancer.
xxDo not short-circuit the battery.
xxThe batteries in this equipment may
explode if disposed of in a fire.
xxDo not charge the batteries in any
charger other than the one specified
in the owner's manual. Using another
English - 23
charger may damage the battery or
cause it to explode.
xxAs part of our commitment to protecting our
environment and
conserving natural
resources, Uniden
voluntarily participates
in an RBRC® industry
program to collect and
recycle used Ni-MH batteries within
the United States. Please call
1-800-8-BATTERY for information on
Ni-MH battery recycling in your area.
(RBRC® is a registered trademark of the
Rechargeable Battery Recycling
Corporation.)
Rechargeable batteries must be
recycled or disposed of properly.
Warning! The cords on this
product and/or accessories contain
lead, a chemical known to the
state of California to cause birth
defects or other reproductive
harm. Wash hands after handling.
Uniden works to reduce lead
content in our products &
accessories.
Compliance Information
FCC Part 68 Information
This equipment complies with Part
68 of the FCC rules and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that
contains, among other information,
a product identifier in the format US:
AAAEQ##TXXXX. If requested, this
number must be provided to the phone
company.
An applicable Universal Service
Order Codes (USOC) certification for
the jacks used in this equipment is
provided (i.e., RJ11C) in the packaging
with each piece of approved terminal
24 - English
equipment. A plug and jack used to
connect this equipment to the premises
wiring and telephone network must
comply with the applicable FCC Part
68 rules and requirements adopted by
the ACTA. A compliant telephone cord
and modular plug is provided with
this product. It is designed to be connected to a compatible modular jack
that is also compliant. See installation
instructions for details.
The REN is used to determine the
number of devices that may be connected to a phone line. Excessive RENs
on a phone line may result in devices
not ringing in response to an incoming call. In most but not all areas, the
sum of RENs should not exceed five
(5.0). To be certain of the number of
devices that may be connected to a
line, as determined by the total RENs,
contact the telephone provider. The
REN for this product is part of the
product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the
telephone network, the telephone company will notify you in advance that
temporary discontinuance of service
may be required. But if advance notice
isn't practical, the telephone company
will notify the customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC
if you believe it is necessary. The telephone company may make changes in
its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens
the telephone company will provide
advance notice in order for you to make
necessary modifications to maintain
uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery replacement
section); otherwise do not substitute or
repair any parts of the device except as
specified in this manual. Connection
to party line service is subject to state
tariffs. Contact the state public utility
commission, public service commission or corporation commission for
information. This equipment is hearing
aid compatible.
If you experience trouble with this
equipment, contact the manufacturer (see the cover of this manual for
contact information) or an authorized
agent. If the equipment is causing harm
to the telephone network, the telephone
company may request that you disconnect the equipment until the problem
is resolved.
If your home has wired alarm equipment connected to a phone line, be sure
that installing the system does not disable your alarm equipment. If you have
questions about what will disable alarm
equipment, contact your telephone
company or a qualified installer.
Any changes or modifications to this
product not expressly approved by the
manufacturer or other party responsible for compliance could void your
authority to operate this product.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes,
are very destructive to telephone
equipment connected to AC power
sources. To minimize damage from
these types of surges, a surge arrestor is
recommended.
FCC Part 15 Information
This device complies with part 15 of
the FCC rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept
any interference received, including
interference that may cause undesired
operation. Privacy of communications
may not be ensured when using this
phone.
FCC PART 15.105(b): Note: This
equipment has been tested and found
to comply with the limits for a Class
B digital device, pursuant to part 15
of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not
installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to
try to correct the interference by one or
more of the following measures:
xxReorient or relocate the receiving
antenna.
xxIncrease the separation between the
equipment and receiver.
xxConnect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
xxConsult the dealer or an experienced
radio/TV technician for help.
FCC RF Exposure Information
This product complies with FCC radiation exposure limits under the following conditions:
xxThe base must be placed to allow a
minimum of 20 cm (8 inches) between
the antenna and all persons during
normal operation.
xxThe base must not be collocated or
operated in conjunction with any other
antenna or transmitter.
xxThe handset is designed for body-worn
operation and meets FCC RF exposure
guidelines when used with any belt clip,
English - 25
carrying case, or other accessory supplied with this product. (All necessary
accessories are included in the package;
any additional or optional accessories
are not required for compliance with
the guidelines.) Third party accessories
(unless approved by the manufacturer)
should be avoided as these might
not comply with FCC RF exposure
guidelines.
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE: This equipment meets the
applicable Industry Canada Terminal
Equipment Technical Specifications.
This is confirmed by the registration
number. The abbreviation IC before
the registration number signifies that
registration was performed based on a
Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not
imply that Industry Canada approved
the equipment.
NOTICE: The Ringer Equivalence
Number (REN) for this terminal equipment is marked on the equipment itself.
The REN assigned to each terminal
equipment provides an indication of
the maximum number of terminals
allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of
devices subject only to the requirement
that the sum of the Ringer Equivalence
Numbers of all the devices does not
exceed 5.
Radio equipment
The term IC before the radio certification number only signifies that
Industry Canada technical specifications were met. Operation is subject
to the following two conditions: (1)
this device may not cause interference,
and (2) this device must accept any
interference, including interference
that may cause undesired operation of
26 - English
the device. "Privacy of communications
may not be ensured when using this
telephone".
1-Year Limited Warranty
Evidence of original purchase is
required for warranty service.
WARRANTOR: UNIDEN AMERICA
CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden
warrants, for one year, to the original
retail owner, this Uniden Product to
be free from defects in materials and
craftsmanship with only the limitations
or exclusions set out below.
WARRANTY DURATION: This
warranty to the original user shall
terminate and be of no further effect
12 months after the date of original
retail sale. The warranty is invalid if
the Product is (A) damaged or not
maintained as reasonable or necessary,
(B) modified, altered, or used as part of
any conversion kits, subassemblies, or
any configurations not sold by Uniden,
(C) improperly installed, (D) serviced
or repaired by someone other than an
authorized Uniden service center for a
defect or malfunction covered by this
warranty, (E) used in any conjunction
with equipment or parts or as part of
any system not manufactured by Uniden, or (F) installed or programmed
by anyone other than as detailed by the
owner's manual for this product.
STATEMENT OF REMEDY: In
the event that the product does not
conform to this warranty at any time
while this warranty is in effect, warrantor will either, at its option, repair or
replace the defective unit and return it
to you without charge for parts, service,
or any other cost (except shipping and
handling) incurred by warrantor or its
representatives in connection with the
performance of this warranty. Warrantor, at its option, may replace the unit
with a new or refurbished unit. THE
LIMITED WARRANTY SET FORTH
ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE
PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION
OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE. THIS WARRANTY DOES
NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not
allow this exclusion or limitation of
incidental or consequential damages
so the above limitation or exclusion
may not apply to you.
LEGAL REMEDIES: This warranty
gives you specific legal rights, and
you may also have other rights which
vary from state to state. This warranty
is void outside the United States of
America and Canada.
PROCEDURE FOR OBTAINING
PERFORMANCE OF WARRANTY:
If, after following the instructions in
the owner's manual you are certain
that the Product is defective, pack
the Product carefully (preferably in
its original packaging). Disconnect
the battery from the Product and
separately secure the battery in its
own separate packaging within the
shipping carton. The Product should
include all parts and accessories
originally packaged with the Product.
Include evidence of original purchase
and a note describing the defect that
has caused you to return it. The Product should be shipped freight prepaid,
by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
Minimum size: 0.375 in wide (9.525 mm)
Minimum drawing size (with clear space) = 0.555 in (14.1 mm) wide
As an Energy Star® Partner,
Uniden has determined
that this product meets
the Energy Star®
guidelines for energy
efficiency. Energy Star® is
a U.S. registered mark.
xxUniden® is a registered trademark of
Uniden America Corporation.
xxThe pictures in this manual are for
example only. Your phone may not
look exactly like the pictures.
English - 27
28 - English
Download PDF

advertising