SEKURE | DGP2-648 | Installation manual | SEKURE DGP2-648 Installation manual

V1.4
96-Zone Expandable Security and Access Control Panel
DGP-NE96
Reference and Installation Manual
www.paradox.ca
TABLE OF CONTENTS
INTRODUCTION ............................................................... 3
Features ................................................................................... 3
Specifications ........................................................................... 3
INSTALLATION ............................................................... 4
Recommended Installation Procedure ..................................... 4
Location & Mounting ................................................................ 4
Earth Ground............................................................................ 4
AC Power ................................................................................. 4
Backup Battery......................................................................... 4
Auxiliary Power Terminals........................................................ 4
Bell/siren Output....................................................................... 4
Programmable Outputs ............................................................ 4
Keyswitch Connections ........................................................... 4
Access Control Connections .................................................... 4
Calculating Power Requirements............................................. 6
Keypad Zone Connections....................................................... 7
Addressable Zone Connections ............................................... 7
Double Zone Connections........................................................ 8
Connecting the DGP2-ZX4 ...................................................... 8
Combus Connections............................................................... 9
Fire Circuits .............................................................................. 9
Telephone Line Connections ................................................... 9
Built-in RTC............................................................................ 10
PROGRAMMING METHODS ......................................... 11
WinLoad Uploading/Downloading Software........................... 11
Paradox Memory Key ............................................................ 11
Module Broadcast .................................................................. 11
Programming Through a Keypad ........................................... 11
Module Programming Mode................................................... 11
ZONE PROGRAMMING ................................................. 12
Zone Numbering .................................................................... 12
Zone Doubling (ATZ).............................................................. 13
Zone Definitions ..................................................................... 13
Zone Partition Assignment ..................................................... 14
Zone Options.......................................................................... 14
Input Speed............................................................................ 15
EOL on Hardwire Zones......................................................... 15
Keypad Numbering ................................................................ 15
KEYSWITCH PROGRAMMING ...................................... 16
Keyswitch Numbering ............................................................ 16
Keyswitch Definitions ............................................................. 16
Keyswitch Partition Assignment ............................................. 17
Keyswitch Options.................................................................. 17
Switch To Stay Arming ..........................................................
Always Force Arm when Regular Arming ..............................
Follow Zone Switches to Entry Delay 2 .................................
One-touch Features...............................................................
Exit Delay...............................................................................
Keypad Lock-out Feature ......................................................
Bell Squawk ...........................................................................
Ring-back...............................................................................
Maximum Bypass Entries ......................................................
Display “Bypass” If Armed .....................................................
19
19
19
19
19
20
20
20
20
20
ALARM OPTIONS........................................................... 21
Bell/alarm Output ...................................................................
Bell Cut-off Timer ...................................................................
Wireless Transmitter Supervision Options.............................
Police Code Timer .................................................................
Tamper Recognition Options .................................................
Keypad Panic Options ...........................................................
21
21
21
21
21
22
EVENT REPORTING ...................................................... 23
Reporting Enabled .................................................................
Report Codes.........................................................................
Report Arming and Disarming ...............................................
Monitoring Station Phone # ...................................................
Account Number ....................................................................
Account Number Transmission..............................................
Reporting Formats .................................................................
Event Call Direction ...............................................................
Pager Delay ...........................................................................
Recent Close Delay ...............................................................
Power Failure Report Delay...................................................
Auto Test Report....................................................................
Disarm Reporting Options .....................................................
Zone Restore Report Options................................................
Auto Report Code Programming ...........................................
Closing Delinquency Timer....................................................
24
24
25
26
26
27
27
27
28
28
28
28
28
28
28
29
DIALER OPTIONS .......................................................... 30
Telephone Line Monitoring ....................................................
Tone/pulse Dialing .................................................................
Pulse Ratio ............................................................................
Busy Tone Detection .............................................................
Switch To Pulse .....................................................................
Bell On Communication Fail ..................................................
Keypad Beep on Successful Arm or Disarm Report ..............
Dial Tone Delay .....................................................................
30
30
30
30
30
30
30
30
PROGRAMMABLE OUTPUTS ....................................... 31
ARMING AND DISARMING OPTIONS........................... 18
Arming Follows Partition ........................................................ 18
Restrict Arming on Supervision Loss ..................................... 18
Restrict Arming on Tamper .................................................... 18
Restrict Arming on AC Failure................................................ 18
Restrict Arming on Battery Failure ......................................... 18
Restrict Arming on Bell or Auxiliary Failure............................ 18
Restrict Arming on TLM Failure ............................................. 18
Restrict Arming on Module Troubles ...................................... 18
Timed Auto-Arming ................................................................ 18
No Movement Auto-Arming.................................................... 19
Auto-Arming Options.............................................................. 19
PGM Activation Event............................................................
PGM Deactivation Option ......................................................
Flexible PGM Deactivation Option .........................................
PGM Deactivation Event........................................................
PGM Timer ............................................................................
PGM1 Becomes a 2-wire Smoke Detector Input ...................
PGM Test Mode.....................................................................
31
31
31
31
31
31
31
SYSTEM SETTINGS AND COMMANDS........................ 32
Hardware Reset ..................................................................... 32
Software Reset ...................................................................... 32
Installer Code Lock ................................................................ 32
DIGIPLEXNE CONTROL PANEL 1
Daylight Savings Time ...........................................................
Battery Charge Current..........................................................
Combus Speed ......................................................................
Transmit Zone Status on Serial Port......................................
Serial Port Baud Rate ............................................................
Partitioning.............................................................................
Shabbat Feature ....................................................................
Installer Function Keys ..........................................................
Module Reset.........................................................................
Locate Module .......................................................................
Module Programming ............................................................
Module and Label Broadcast .................................................
System Date & Time..............................................................
Clock Compensation Value ...................................................
Remove Module.....................................................................
Serial Number Viewing ..........................................................
Power Save Mode .................................................................
Auto Trouble Shutdown .........................................................
No AC Fail Display.................................................................
Multiple Action Feature ..........................................................
System Labels .......................................................................
32
32
32
32
32
32
33
33
33
33
33
33
33
34
34
34
34
34
34
34
34
ACCESS CODES............................................................ 36
Installer Code.........................................................................
Access Code Length..............................................................
System Master Code .............................................................
Programming Access Codes .................................................
User Options..........................................................................
Partition Assignment..............................................................
Access Control.......................................................................
36
36
36
36
36
37
37
ACCESS CONTROL: SYSTEM FEATURES ................. 38
Common Access Control Terms............................................
Programming Overview .........................................................
Enable Access Control ..........................................................
Door Numbering ....................................................................
Access Levels........................................................................
Access Schedules .................................................................
Backup Schedules .................................................................
Holiday Programming ............................................................
Schedule Tolerance Window .................................................
Door Access Mode ................................................................
Code Access..........................................................................
Card and Code Access..........................................................
Skip Exit Delay When Arming With Access Card ..................
Restrict Arming on Door ........................................................
Restrict Disarming on Door....................................................
Door Access During Clock Loss ............................................
Burglar Alarm On Forced Door or Door Left Open ................
Logging Access Control Events.............................................
38
38
38
38
38
38
39
39
39
39
39
39
40
40
40
40
40
40
WINLOAD SOFTWARE.................................................. 41
Panel Identifier.......................................................................
PC Password .........................................................................
PC Telephone Number ..........................................................
Call Back Feature ..................................................................
Call WinLoad .........................................................................
Answer WinLoad....................................................................
Answering Machine Override Delay ......................................
Ring Counter..........................................................................
Event Buffer Transmission.....................................................
41
41
41
41
41
41
41
41
41
USER FEATURES .......................................................... 42
2 REFERENCE & INSTALLATION MANUAL
Regular Arming .....................................................................
Stay Arming...........................................................................
Instant Arming .......................................................................
Force Arming.........................................................................
How to Arm............................................................................
Disarming ..............................................................................
Bypass Programming ............................................................
Chime Zones ........................................................................
Keypad Settings ....................................................................
Event Record Display............................................................
Scroll Restart ........................................................................
Trouble Display .....................................................................
Trouble Latch ........................................................................
Clear Bell Current Limit Trouble ............................................
42
42
42
42
42
42
42
43
43
43
43
43
44
44
APPENDIX 1: PGM PROGRAMMING TABLE............... 45
APPENDIX 2: AUTOMATIC REPORT CODE LIST ....... 52
APPENDIX 3: CONTACT ID REPORT CODE LIST....... 54
INDEX.............................................................................. 55
WARNINGS..................................................................... 59
1.0
1
INTRODUCTION
DigiplexNE is a security and access control system with 8 on-board zone
inputs (16 with zone doubling) that is expandable to 96 zones via the 4-wire
combus. DigiplexNE features up to 999 users, 8 partitions, 32 doors, 32
schedules, 16 access levels, and can support up to 127 modules in any
combination.
DigiplexNE systems provide the highest level of protection for banks, highsecurity military and government sites, luxurious residential homes and any
place where maximum security is essential. These systems are designed to
be easy to use, and the modular concept of these systems provides
installer’s with labour-saving features that make expanding, installing and
servicing these systems quick and convenient.
Expand the DigiplexNE system by adding plug-and-play expansion modules
anywhere and in any combination on the 4-wire combus. Modules are
connected to the combus at the most convenient location and then their zone
inputs are assigned to the desired zone and partition. Also, only a module’s
used inputs are assigned to zones in the system. Keyswitches, remote
controls and unused module inputs do not use up zones. Once installed, all
combus modules, including motion detectors, can be programmed remotely
via a keypad or the WinLoad upload/download software.
DigiplexNE also supports 32 virtual zones in addition to its 96 security
zones and 32 access control doors. Virtual zones can be used to automate
PGM activations without occupying a security zone and without affecting
the system’s security functions. DigiplexNE is a logical solution to every
installer’s security, access control and home automation installation needs.
CTR-21 APPROVAL
The DigiplexNE control panel (DGP-NE96) meets the European Union
Common Technical Requirement CTR-21. The CTR-21 requirement is an
electrical standard that defines the analogue interface for all two-wire
telecommunications equipment (i.e. DECT, PABXs, etc.) intended for
connection to the Public Switched Telephone Network. This allows the
DigiplexNE control panel to be used in as many as 19 countries, such as
Belgium, Germany, Greece, Portugal, Sweden and Switzerland.
DigiplexNE control panels with the CTR-21 approval are available as an
option only.
1.1 FEATURES
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
Digital combus:
• Provides constant power, supervision and two-way communication
between the control panel and all its modules
• Supports up to 127 modules
• Connect modules up to 3000ft (914m) from the panel
• Sabotage-proof technology without additional wiring
96 addressable zones
8 partitions
998 user codes, 1 System Master code and 1 installer code
Built-in access control
2048 stored events
1 telephone line and optional secondary telephone line
Remote diagnostics and pager messaging
False alarm prevention features
32 independent keyswitch zones (does not use any of the 96 zones)
8 on-board hardwired input terminals
3 on-board fully programmable outputs (PGMs):
• 1 normally open, high-current transistor output (100mA)
• 2 normally open or normally closed 5A programmable relay outputs
• Up to 32 more PGM inputs through the Keyswitch’s PGM Input
feature
PGM1 can be set as a two-wire smoke detector input
Event reporting:
• a separate dialing sequence for each partition
• 4 Monitoring Station Telephone Numbers
• SIA, Contact ID, Ademco Contact ID Edition 2000, Pager Format
and many more communicator formats
1.2 SPECIFICATIONS
CONTROL PANEL (NON-UL SYSTEMS)
AC Power:
Battery:
Auxiliary Power:
16Vac, 20/40VA, 50-60Hz
12Vdc, 4Ah minimum
12Vdc 600mA typical, 700mA maximum,
fuseless shutdown at 1.1A
Bell Output:
1A, fuseless shutdown @ 3A
PGM Output:
PGM1 (100mA), PGM2 and PGM3 (5A relay)
Event Buffer:
2048 events
All control panel outputs are rated to operate between 10.8Vdc and
12.1Vdc
CONTROL PANEL (UL COMPLIANT SYSTEMS)
AC Power:
Battery:
Auxiliary Power:
16Vac, 40VA, 60Hz
12Vdc, 4Ah minimum
11.4 to 12.5Vdc, 200mA maximum, fuseless
shutdown at 1.1A
Bell Output:
11.4 to 12.5Vdc, 1A maximum, fuseless
shutdown @ 3A
PGM Output:
PGM1 (100mA), PGM2 and PGM3 (5A relay)
Event Buffer:
2048 events
All control panel outputs are rated to operate between 11.4Vdc and
12.5Vdc
Specifications may change without prior notice.
UL Note: The DGP-NE96 control panel has been tested with the LCD Keypad
(DGP2-641) only.
General Note 1
Please note that only LCD and Grafica keypads can be used to program the
DigiplexNE system. LED keypads cannot be used to program the system.
General Note 2
Please note that the steps may differ when programming with the Grafica
keypad (DNE-K07). If not indicated, refer to the complete Grafica User
Manual, which can be downloaded for free from our Web site at
www.paradox.ca.
DIGIPLEXNE CONTROL PANEL 3
2
INSTALLATION
2.1 RECOMMENDED INSTALLATION PROCEDURE
In order to facilitate installation, we recommend connecting the modules in
small groups and verifying the system after every group is connected,
instead of verifying the system only after all modules are connected.
Step 1: Install the control panel.
Step 2: Connect a small group of modules, including a keypad, to the
combus.
Step 3: Connect the battery and then connect the AC power. Enter section
[4000] to verify if all the connected modules’ serial numbers appear
(see section 11.19 on page 34). If all the modules appear in section
[4000], only the Clock Loss trouble and/or Bell Absent trouble
should appear on the keypad. Verify the connection if a module
does not appear in section [4000], or if a module trouble occurs.
Step 4: If another group of modules needs to be connected, disconnect AC
power and the battery, and then continue the installation by
following steps 2, 3 and 4.
Step 5: If modules were removed from the combus, enter [4005] to remove
them from the panel’s memory (see section 11.18 on page 34).
Step 6: Connect an LCD Keypad at various points farthest from the control
panel and use the keypad’s built-in Voltmeter to verify the combus’s
voltage (refer to the Digiplex/DigiplexNE LCD Keypad Reference &
Installation Manual).
2.2 LOCATION & MOUNTING
Before mounting the cabinet, push the five white nylon mounting studs into
the back of the cabinet. Pull all cables into the cabinet and prepare them for
connection before mounting the circuit board into the back of the cabinet.
Select an installation site that is not easily accessible to intruders and leave
at least 2" around the panel box to permit adequate ventilation and heat
dissipation. The installation site should be dry and close to an AC source,
ground connection and telephone line connection.
2.3 EARTH GROUND
Connect the zone and dialer ground terminals from the control panel to the
enclosure and cold water pipe or grounding rod as per local electrical codes.
For maximum lightning protection, use separate earth grounds
for the zone and dialer grounds (see Figure 2-3 on page 5).
2.4 AC POWER
Use a 16.5Vac (50/60Hz) transformer with a minimum 20VA rating to
provide sufficient AC power. For increased power use a transformer with a
40VA rating. For UL Listed systems, use model #BE156240CAA. For CSA
listed systems, use model #BE116240AAA. Do not use any switchcontrolled outlets to power the transformer. Connect the transformer as
shown in Figure 2-3 on page 5.
Do not connect the transformer or the backup battery until all
wiring is completed.
PLEASE NOTE: When powering up the DGP-NE96 control
panel (V1.02 or higher), the panel will begin a module scan to
verify if all the modules connected to the control panel are
operational. The scanning process will take between 30 and
120 seconds to complete depending on the number of
modules connected to the control panel. The module scan is
complete when the keypad begins to show the partition status.
Only after the module scan is complete will the control panel
be fully operational.
2.5 BACKUP BATTERY
To provide power during power loss, connect a 12Vdc 4Ah rechargeable
acid/lead or gel cell backup battery (YUASA model #NP7-12
recommended) as shown in Figure 2-3 on page 5. Connect the backup
battery after applying AC power. When installing, verify proper polarity, as
reversed connections will blow the battery fuse. For details on how to set
the Battery Charge Current to either 350mA or 700mA, see section 11.5.
4 REFERENCE & INSTALLATION MANUAL
2.5.1 Battery Test
The control panel conducts a dynamic battery test under load every 64
seconds. If the battery is disconnected, if its capacity is too low or if the
battery voltage drops to 10.5 volts or less when there is no AC, the “Battery
Trouble” message will appear in the Trouble Display. At 8.5 volts, the panel
shuts down and all outputs close.
2.6 AUXILIARY POWER TERMINALS
The auxiliary power supply can power the motion detectors, keypads and
other accessories in the security system. A fuseless circuit protects the
auxiliary output against current overload and automatically shuts down if
the current exceeds 1.1A. Auxiliary power will resume once the overload
condition has restored. For details on available output power, please refer
to Figure 2-3 on page 5. To calculate power consumption, see Calculating
Power Requirements on page 6.
2.7 BELL/SIREN OUTPUT
The BELL+ and BELL- terminals power bells and/or other warning devices
that require a steady voltage output during an alarm. The bell output
supplies 12Vdc upon alarm and can support one 30-watt or two 20-watt
sirens. The bell output uses a fuseless circuit and will automatically shut
down if the current exceeds 3A. If the load on the BELL terminals returns to
normal (≤3A), the control panel will re-instate power to the BELL terminals.
When connecting sirens, please verify correct polarity as shown in Figure
2-3. PGM2 and PGM3 are relays rated at 5A each and can be used to
power bells and/or other warning devices by programming them as a bell/
siren outputs (see section 10 on page 31).
When the bell output is not used, the “Bell Absent” message
appears in the Trouble Display. To avoid this, connect a 1kΩ
resistor across the bell output. UL Note: The keypads must be
programmed to beep with all troubles.
2.8 PROGRAMMABLE OUTPUTS
The control panel comes standard with
PGM1 to PGM3. When a specific event or
condition occurs in the system, a PGM can
be programmed to reset smoke detectors,
activate strobe lights, open/close garage
doors and much more. For details on how to
program the PGMs, refer to section 10.
Figure 2-1: PGM & Relay
PGM1 is 100mA (max.) normally open
output. PGM2 and PGM3 are 5A relay
outputs that can be normally open or
normally closed. If the current draw on
PGM1 is to exceed the current output, we
recommend using a relay as shown in
Figure 2-1. PGM1 can be programmed as a
2-wire smoke detector input (see section
2.17.1 on page 9 and section 10.6 on page 31).
2.9 KEYSWITCH CONNECTIONS (NOT VERIFIED BY UL)
Connect the keyswitches to the keypad,
control panel, or Zone Expansion Module's
hardwired input terminals as shown in Figure
2-2. Once a keyswitch is connected, it must be
assigned a keyswitch zone and its parameters
must be defined as described in Keyswitch
Programming on page 16.
Figure 2-2: Keyswitch
2.10 ACCESS CONTROL CONNECTIONS
For all access control explanations and connection drawings, refer to
Access Control: System Features on page 38.
Figure 2-3: DigiplexNE Control Panel Wiring Diagram
Red "LINE#1" and "LINE#2" LEDs:
Illuminated - If the control panel is using a telephone line, the panel
will display which line it is using by illuminating a telephone line LED.
If the control panel is using Line 1, the "LINE#1" LED will be
illuminated. If the control panel is using Line 2, the "LINE#2" LED
will be illuminated.
Red "STATUS" LED:
Flashing - Indicates proper operation.
Fast Flash - Indicates a control panel failure.
Off - Control panel error.
Built-in RTC
See also the "MEM KEY/TM1"
connector warning.
Charging and battery test LED
(every 64 seconds).
Same ground
connections as the
panel, but do not connect
the DGP2-ZX4's ground
directly to the control
panel's ground.
For the hardwire connections,
see Single Zone and Double
Zone Connections.
Four pin connector can
be used for quick
installation of a keypad
or module.
CAUTION: Disconnect
the battery before
replacing the fuse.
Reset Jumper
Optional connector can
be used to recharge
another battery in the
system or to the
connect a secondary
battery.
Combus
12Vdc 7Ah Rechargeable
Acid/Lead or Gel Cell
Backup Battery
AUX Power (Auxiliary):
Refer to the transformer requirements for the
Auxiliary Power Output. Also, refer to the
Power Unit Consumption Table. To connect
additional wiring to auxiliary power, use the
red (+) and black (-) keypad connectors.
Auxiliary power will shut down if the current
exceeds 1.1A.
WARNING:
Improper connection may result
in damage to the system.
Transformer Requirements:
For the hardwired connections, see Single Zone Input
Connections on page 8 and Double Zone Connections
on page 8.
WARNING!
Do not connect a DGP2-TM1
Time Module to the
"mem key/tm1" connector.
Connecting a DGP2-TM1 will
create time errors within the
panel and features that use the
control panel's internal clock
(ex.: Auto-arming) will not
function correctly.
AWG#14 single
conductor
solid copper
wire
To metallic
enclosure
Ground
clamp
Cold water pipe
grounding
To provide maximum lightning protection we
strongly recommend having separate earth
connections for the dialer and zone ground
terminals.
Minimum:
16.5VAC; 20VA
Auxiliary Supply can provide: typical 600mA
max. 700mA
Usable Battery Charge
Currents:
Bell/Siren
350mA
The "bell"
output will
shutdown if
the current
exceeds 3A.
1K9
resistor*
1K9
resistor*
Bell/Siren
*A 1K9 resistor is
required if the Bell is
not equipped with an
internal resistor. The
resistor must be
connected between
the Bell's negative (-)
and positive (+) wires.
Position the resistor as
close as possible to
the Bell. A resistor is
not required for sirens.
Door Contact
* if EOL is enabled in the
control panel
The combus supports a maximum of 127 modules. Although
external power supplies can be used to provide power to
modules connected far from the control panel, the total
distance of all runs of wire combined cannot exceed 914m
(3000ft). For example, if ten runs of wire measuring 305m
(1000ft) each are connected to the control panel, the total
distance would be 3048m (10, 000ft), which exceeds the
system's capacity.
WARNING: Before adding any module to the control panel
make sure you shutdown the control panel by removing AC
power and the battery.
When installing the combus wires in a noisy environment, or
when connecting the combus across separate buildings, you
must use a shielded cable. Refer to section 2.16.1 on page 9.
Please see “UL and ULC Warnings” on page 59 for applicable
UL/ULC warnings and information.
PLEASE NOTE: It is strongly recommended that you test your
system on a weekly basis, and have your system checked by a
qualified technician a minimum of every 3 years.
PLEASE NOTE: When powering up the DGP-NE96 control panel (V1.02 or higher), the panel will begin a module scan to verify if all the modules connected to the panel are operational. The scanning
process will take between 30 and 120 seconds to complete depending on the number of modules connected to the control panel. The module scan is complete when the LCD keypad begins to show the
partition status. Only after the module scan is complete will the control panel be fully operational.
DIGIPLEXNE CONTROL PANEL 5
2.11 CALCULATING POWER REQUIREMENTS
Table 1: Power Unit Consumption Table
Description
QTY.
PU used by each
Total PU
Grafica Graphic LCD Keypad (DNE-K07):
_______
X
150PU =
__________ PU
LCD Keypad (DGP2-641):
_______
X
80PU =
__________ PU
LED Keypad (DGP2-648):
_______
X
115PU =
__________ PU
Addressable Detectors (DG85, DGP2-50/60/70):
_______
X
30PU =
__________ PU
Addressable Door Contact (DGP2-ZC1):
_______
X
30PU =
__________ PU
1-Zone Hardwire Expansion Module (DGP2-ZX1):
_______
X
14PU =
__________ PU
4-Zone Hardwire Module (APR3-ZX4):
_______
X
28PU =
__________ PU
8-Zone Hardwire Module (APR3-ZX8):
_______
X
28PU =
__________ PU
Wireless Module (OMN-RCV3):
_______
X
50PU =
__________ PU
1-PGM Output Module (APR3-PGM1):
_______
X
28PU =
__________ PU
4-PGM Output Module (APR3-PGM4):
_______
X
150PU =
__________ PU
Printer Module (APR3-PRT1):
_______
X
40PU =
__________ PU
DVACS Module (DGP2-DVAC):
_______
X
40PU =
__________ PU
Annunciator Module (DGP2-ANC1):
_______
X
105PU =
__________ PU
InTouch Voice-Assisted Arm/Disarm Module (APR3-ADM2):
_______
X
105PU =
__________ PU
Access Control Module (DGP2-ACM1P):
Note: The DGP2-ACM1P consumes 165PU from its own power supply
_______
X
165PU =
__________ PU
Maximum available power units = 700PU
GRAND TOTAL
__________ PU
STEP 1:
Using Table 1, calculate the total number of power units (PU) required by each device, module, and accessory in the system. Please take into
account devices connected to the control panel’s PGM outputs. Since the BELL output has its own power supply, do not include the sirens
connected to it in the calculation.
STEP 2:
If Grand Total is less than 700PU, go to step 3. If the value is greater, an external power supply is required (see Figure 2-5 on page 7) to provide the
additional power needed. Proceed with step 3 and refer to the example in Figure 2-4 on page 7.
STEP 3:
Due to the degradation of a power signal over long distances, EACH length or run of wire in the system can support only a specific number of
power units (PU). Using Table 2, determine how many power units each length of wire can support. Please note that the total number of power
units (PU) can never surpass 700PU.
Table 2: Power Unit (PU) Limitations For Each Run of Wire
Gauge: 18AWG, Surface: 0.823mm2
Gauge: 22AWG, Surface: 0.326mm2
Gauge: 24AWG, Surface: 0.205mm2
Length of each
run of wire
Available Power
Units (PU)
Length of each
run of wire
Available Power
Units (PU)
Length of each
run of wire
Available Power
Units (PU)
100ft. (30m)
700
100ft. (30m)
700
100ft. (30m)
700
200ft. (61m)
700
200ft. (61m)
682
200ft. (61m)
429
300ft. (91m)
700
300ft. (91m)
454
300ft. (91m)
286
400ft. (122m)
700
400ft. (122m)
341
400ft. (122m)
214
500ft. (152m)
690
500ft. (152m)
273
500ft. (152m)
171
600ft. (183m)
575
600ft. (183m)
227
600ft. (183m)
143
700ft. (213m)
493
700ft. (213m)
195
800ft. (244m)
431
800ft. (244m)
170
900ft. (274m)
383
900ft. (274m)
151
1000ft. (305m)
345
1000ft. (305m)
136
1500ft. (457m)
230
2000ft. (610m)
172
2500ft. (762m)
138
3000ft. (914m)
115
6 REFERENCE & INSTALLATION MANUAL
Figure 2-4: Sample Power Requirement Calculations
Figure 2-5: External Power Supply Connections
Power required by devices connected to control panel’s
auxiliary output must not exceed the auxiliary output’s limit:
(A) + (B) + (C) + (D) + (E) + (F) + (G) = 368PU<700PU = OK
Control Panel
aux. output
= 700PU
15m (50ft)
61m (200ft)
APR3-PRT1
(A) = 40PU
Power units required by devices
connected to a power supply do not
draw power from the control panel’s
auxiliary output.
DGP2-641
(D) = 80PU
Module
7.5m (25ft)
15m (50ft)
DGP2-70
(E) = 30PU
APR3-ZX8
(B) = 28PU
22 AWG
30m (100ft)
As indicated in Table 2 on
page 6, this run of wire can
support 700PU. Total PU on
this run of wire:
(A) 40PU + (B) 28PU =
68PU<700PU = OK
7.5m (25ft)
DGP2-641
(F) = 80PU
15m (50ft)
Power Supply
DGP2-641
(G) = 80PU
290m (950ft)
DGP2-60
(C) = 30PU
305m (1000ft)
As indicated in Table 2 on
page 6, this run of wire
can support 136PU. Total
PU on this run of wire:
(A) 40PU + (C) 30PU =
70PU<136PU = OK
500ft. from control panel
500ft. from control panel’s aux. output
Therefore this run = max. 273PU
91m (300ft)
As indicated in Table 2
on page 6, this run of
wire can support 454PU.
Total PU on this run of
wire:
(D) 80PU + (E) 30PU +
(F) 80PU + (G) 80PU
= 270PU<454PU = OK
An LCD Keypad (80PU) can be added to the 100ft. or 300ft. wire in Figure
2-4, but adding an LCD Keypad to the 1000ft. wire would exceed the wire’s
limits and cause devices to function at decreased capacity.
Module
2000ft. from control panel
500ft. from power supply
Therefore this run = max. 273PU
Do not use the same transformer for the control panel and the
external power supplies. Do not install modules more than
3000ft (914m) from the control panel.
2.12 KEYPAD ZONE CONNECTIONS
Every keypad, except Grafica, has one hardwire input terminal allowing you
to connect a detector or door contact directly to the keypad. For example, a
door contact located at the entry point of an establishment can be wired
directly to the input terminal of the entry point keypad instead of back to the
control panel.
Even with the ATZ feature enabled in the control panel, only
one device can be connected to the keypad’s hardwired input
terminal. Tamper is not recognized on keypad zones. The
keypad zone follows the control panel’s EOL definition.
A device connected to the keypad’s input terminal must be assigned to a
zone in the control panel and the zone’s parameters must be defined (see
Zone Programming on page 12). The keypad communicates the status of
the zone to the control panel via the combus. The detection device is
connected as shown in Figure 2-3 on page 5.
2.13 ADDRESSABLE ZONE CONNECTIONS
The control panel includes eight hardwired input terminals for use with
traditional hardwired (non-combus) door contacts, smoke detectors and/or
motion detectors.
The control panel also supports several hardwire zone expansion modules.
Devices connected to hardwired input terminals must be assigned to a
zone and the zone's parameters must be defined (see Zone Programming
on page 12). Figure 2-6 shows single zone (ATZ disabled) hardwire input
terminal connections recognized by the DigiplexNE system. For UL listed
installations, use EOL resistor part #2011002000.
DIGIPLEXNE CONTROL PANEL 7
Figure 2-6: Single Zone Input Connections
2.14 DOUBLE ZONE CONNECTIONS
Enabling the ATZ feature (see section 4.2) allows you to install two
detection devices per input terminal. Connect the devices as shown in
Figure 2-7. Devices connected to input terminals must be assigned to a
zone and the zone's parameters must be defined (see Zone Programming
on page 12). For UL listed Burglary System installations only, use EOL
resistor part #2011002000.
Figure 2-7: Double Zone Connections
Enable ATZ (see section 4.2 on page 13)
and connect as follows (extra input
cannot be used)
2.15 CONNECTING THE DGP2-ZX4
The 4-Zone Expansion Plug-in Device* (DGP2-ZX4*) provides four
additional hardwired input terminals (8 zones with ATZ enabled). It
connects directly to the control panel through its on-board EXPANSION
connector as shown in Figure 2-3: on page 5. Connect detection devices to
the DGP2-ZX4's terminals in the same way that they are connected to the
control panel as shown in Figure 2-6 or Figure 2-7 on page 8. Devices
connected to hardwired input terminals must be assigned to a zone and the
zone's parameters must be defined (Zone Programming on page 12). For
the 4-Zone Expansion Module (APR3-ZX4), refer to the DigiplexNE
Modules Programming Guide.
* Do not use with UL Listed systems.
8 REFERENCE & INSTALLATION MANUAL
2.16 COMBUS CONNECTIONS
2.17.3 Smoke Detector Installation (4-Wire)
Modules can connect anywhere on the 4-wire combus, which can support
up to 127 modules. Connect in a star and/or daisy chain configuration as
shown in Figure 2-3 on page 5. The total distance of all runs of wire cannot
exceed 914m (3000ft). For example, if ten runs of wire measuring 305m
(1000ft) each are connected to the control panel, the total distance would
be 3048m (10,000ft), which exceeds the system’s capacity. To assign a
detection device to a zone in the control panel, see “Zone Programming” on
page 12.
Recommended: System Sensor model
2112/24D smoke detectors. Connect the
4-wire smoke detectors and a relay as
shown in Figure 2-9. To comply with
UL955, install the 4-wire smoke detectors
with 18 gauge wire. If power is
interrupted, the relay causes the control
panel to transmit the Fire Loop Trouble
report programmed in section [2906].
Before connecting a module to the combus, remove AC and
battery power from the control panel.
2.16.1 Connecting the Combus in Noisy Environments
When installing the combus wires in proximity to high electrical
interferences such as neon lights, motors, high-voltage wiring,
transformers, or if connecting the combus across separate buildings, you
must use shielded cables. Connect the shielded cable as detailed below:
Within the Same Building: Strip the outer jacket at one end of the
shielded cable to expose the shield and connect the shield to the control
panel ground (not the dialer ground), while leaving the shield at the other
end of the cable open (floating).
Across Separate Buildings: Strip the outer jacket at one end of the
shielded cable to expose the shield. In the same building that houses the
control panel, connect the exposed shield to a cold water pipe or any other
earth ground available, while leaving the shield at the other end of the cable
open (floating). The same configuration applies for any subsequent
building.
2.17 FIRE CIRCUITS
Connect the smoke detectors using any of the following methods. Assign
the smoke detectors connected to the control panel or zone expansion
input terminals to a zone and define the zone's parameters as a Fire Zone
(see section 4 on page 12).
To reset (unlatch), connect the smoke
detector’s negative (-) to a PGM. Then
program the PGM with the “Smoke
Detector Power Reset” activation event
(see section 10.1 on page 31; Event
Group #067, start # 004, end # 004) to
interrupt power to the smoke detector for
four seconds when the [CLEAR] and
[ENTER] keys are pressed and held for two
seconds.
Note: It is recommended that the
smoke detectors be connected in a
daisy chain configuration.
If ATZ is enabled (see see section 4.2 on page 13), do not use
the extra input (doubled zone). For example, in this example
input 13 cannot be used.
2.18 TELEPHONE LINE CONNECTIONS
Depending on the installation, the telephone lines can be connected directly
to the control panel or through a CA38A or RJ31 as shown in Figure 2-10.
The secondary telephone line terminals (optional) can be used as a backup
telephone line. If the Event Call Direction process fails and the control panel
is unable to communicate with the Monitoring Station through the main line,
the control panel will switch to the second line and repeat the Event Call
Direction process (see section 8.8 on page 27).
UL Note: Installer must verify line seizure after every installation
Figure 2-10: Telephone Line Connection Examples
Example 1:
2.17.1 Smoke Detector Installation (2-Wire)*
PGM1 can be defined as a 2-wire
smoke detector input (see section
10.6). Connect the 2-wire smoke
detectors as shown in Figure 2-8
using a 1kΩ EOL resistor. If a line
short occurs or the smoke detector
activates, whether the system is
armed or disarmed, the control panel
will generate an alarm. If the line is
open, the “Zone Fault” trouble
indication appears in the Trouble
Display and the report code is sent to
the Monitoring Station, if programmed.
Figure 2-9: 4-Wire Detectors
DigiplexNE
Dialer
Figure 2-8:
2-Wire Detectors
PGM1 becomes
input# 255
N.O. contacts
1K9
EOL
Smoke detectors
Ground
clamp
Main line
2nd line
Note: It is recommended that the smoke
detectors be connected in a daisy chain
configuration.
Example 2:
* UL Note: Not to be used with UL Listed systems.
DigiplexNE
Dialer
2.17.2 ESL CleanMe® Installation
The DigiplexNE control panel supports ESL smoke detectors that have the
CleanMe® feature. Connect ESL smoke detectors like the standard smoke
detectors shown in Figure 2-8. Avoid connecting more than 20 ESL smoke
detectors. When an ESL smoke detector sends a CleanMe signal, the
control panel will generate a Zone Fault trouble and, if programmed, will
transmit the Fire Loop report code to the Monitoring Station. The trouble will
be cleared if there is no CleanMe signal for 255 seconds. If an alarm
occurs, the trouble will be cleared until it is detected again.
Ground
clamp
2nd line
Main line
DIGIPLEXNE CONTROL PANEL 9
Example 3:
DigiplexNE
Dialer
Ground
clamp
Main line
2nd line
Example 4:
DigiplexNE
Dialer
Ground
clamp
2nd line
Main line
For TBR-21 compliance, please note the following:
1) The DGP-NE96 can be connected to the telephone network via an RJ11 connector.
2) The Maximum Dialing Attempts cannot exceed 15 attempts (page 28).
2.19 BUILT-IN RTC
The DigiplexNE incorporates an RTC directly on the PC board. The RTC
will save the DigiplexNE’s internal clock when both the AC and battery
power have been lost. After power is lost and then restored, the DigiplexNE
will verify with and then retrieve the time from the RTC. The control panel
will verify and compare its time with the time stored in the RTC every hour.
If the times are different, the DigiplexNE will reset its internal clock to the
time saved in the RTC. The RTC uses a 3V lithium battery (CR2032) with a
battery life of 11 years. Change the battery as shown below:
Figure 2-11: Changing the RTC’s Battery
3V Lithium Battery
(CR2032)
Insert the battery with
the positive facing up
and the negative
facing down
Reprogram the control panel’s clock after changing the battery.
WARNING! Danger of explosion exists if the lithium battery is
incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
10 REFERENCE & INSTALLATION MANUAL
3
PROGRAMMING METHODS
DigiplexNE can be programmed using the following methods:
3.4 PROGRAMMING THROUGH A KEYPAD
3.1 WINLOAD UPLOADING/DOWNLOADING SOFTWARE*
Use the Programming Guide to record how the sections were programmed.
To enter programming mode:
We highly recommend programming the control panel with WinLoad as it
greatly simplifies the process and reduces potential data errors. Refer to
Winload Software on page 41 for details.
* UL Note: Not verified by UL
3.2 PARADOX MEMORY KEY (NOT TO BE USED WITH UL LISTED SYSTEMS)
The Paradox Memory Key can copy the programmed contents of one
control panel into as many others as needed. Downloading is completed in
less than 5 seconds.
Copy to Memory Key
1) Place the Memory Key on the control panel’s
connector labeled MEM KEY. Make sure that the write
protect jumper is on.
2) Enter section:
[4020] to copy the control panel’s contents except
sections [0001] to [0096] and [0501] to [0532] to the
key.
[4021] to copy the control panel’s contents
including sections [0001] to [0096] and [0501] to [0532] to the key.
3) When the keypad emits a Confirmation Beep, remove the Memory
Key. Remove the jumper to prevent accidentally overwriting the
Memory Key’s contents.
Download to Control Panel
1) Place the Memory Key on the control panel’s
connector labeled MEM KEY.
2) Enter section:
[4010] to download the Memory Key’s contents
except sections [0001] to [0096] and [0501] to
[0532] to the control panel.
[4011] to download the contents of the Memory Key
including sections [0001] to [0096] and [0501] to
[0532] to the control panel.
3) When the keypad emits a Confirmation Beep, remove the Memory Key.
Figure 3-1: Using the Memory Key
Jumper ON =
Can copy and download
contents of the Memory Key
Jumper OFF =
Cannot override contents
of the Memory Key
1)
2)
3)
4)
Press and hold the [0] key
Key in the [INSTALLER CODE] (Default is 000000)
Key in the 4-digit [SECTION]
Key in required [DATA]. Refer to the Programming Guide or to the
corresponding sections in this manual.
For LCD Keypads: The control panel will save the data and automatically
advance to the next section or press the [ENTER] key to save the data and
advance to the next section. Press the [CLEAR] key to revert to the
preceding step or to erase the current data entry.
For Grafica Keypads: After entering the required data, press Grafica’s
center action key (Save) to save the data and advance to the next section.
Press the right action key (Exit) to revert to the preceding step or press the
left action key (Clear) to erase the current data.
3.4.1 Feature Select Programming
Most of the options are programmed using the Feature Select Method.
For LCD Keypads: Each number from 1 to 8 corresponds to a specific
feature or option. Set these options by turning the number corresponding to
the feature ON or OFF. The option is considered ON when the number
appears within the brackets on the LCD keypad. Turn options ON and OFF by
pressing the corresponding keys on the keypad. Press the keys as many
times as needed to select the desired options and then press [ENTER] to save.
For Grafica Keypads: Select or clear the check boxes pertaining to the
options or features that you wish to enable or disable. You can also set the
options by pressing the corresponding keys on the keypad. The feature is
considered ON when its check box is selected. To save the settings, press
the Grafica’s center action key (Save).
3.4.2 Decimal Programming
Certain sections may require the entry of a 3-digit decimal value from 000
to 255.
3.4.3 Hexadecimal Programming
Certain sections may require the entry of one or more Hexadecimal values
from 0 to F. Press:
For LCD Keypads:
[0] to [9]
= values 0 to 9 respectively
[STAY] key
=A
[DISARM] key = D
[FORCE] key
=B
[BYP] key
=E
[ARM] key
=C
[MEM] key
=F
For Grafica Keypads:
[0] to [9]
= values 0 to 9 respectively
[#]
= A to F (press the key until the desired letter appears)
3.5 MODULE PROGRAMMING MODE
All modules are programmed through any LCD or Grafica keypad in the
system. To do so, enter Module Programming Mode:
3.3 MODULE BROADCAST
Keypads and other modules can also be programmed easily by using
Module Broadcast (see section 11.15 on page 33). Once a module is
programmed, its sections can be sent to other similar modules through the
combus.
1)
2)
3)
4)
5)
Press and hold the [0] key
Key in the [INSTALLER CODE] (Default is 000000)
Key in section [4003]
Key in 8-digit [SERIAL NUMBER] of the module
Key in 3-digit [SECTION] and required [DATA]. Refer to the Module
Programming Guide for details.
The control panel will redirect all programming to the selected module. To
exit the Module Programming Mode, press the [CLEAR] key on LCD
keypads, or the right action key (Exit) on Grafica keypads, as many times
as needed to return to the desired screen. The module's serial number can
be located on the module's PC board.
DIGIPLEXNE CONTROL PANEL 11
4
ZONE PROGRAMMING
All detection devices connected to the control panel, keypads and zone expansion modules must be assigned to a zone and that zone must be defined as
described in this section.
Figure 4-1: Zone Programming
Zone Definitions
Press & hold the
[0] key
0- Disabled (Default) 8- 24Hr Gas
1- Entry Delay 1
9- 24Hr Heat
2- Entry Delay 2
A- 24Hr Water
3- Follow
B- 24Hr Freeze
4- Instant
C- Delayed 24Hr Fire
5- 24Hr Buzzer
D- Standard 24Hr Fire
6- 24Hr Burglary
E- Stay Delay 1
7- 24Hr Hold-up
F- Stay Delay 2
Key in the
[INSTALLER CODE]
Key in 4-digit
[SECTION]
Zone Numbering
Sections [0001] to [0096] represent
zones 1 to 96 respectively
Enter the 8-digit
[SERIAL NUMBER] of the
addressable detection device or
module that has a hardwire
device connected to it.
Enter the module’s 3-digit
[INPUT NUMBER] where the
hardwire device is connected.
NOTE: For addressable PIRs, door
contacts and keypads, no input # is
required
Select one
only
Zone Partition Assignment
1- Zone Assigned to Partition 1 (Default)
2- Zone Assigned to Partition 2
3- Zone Assigned to Partition 3
4- Zone Assigned to Partition 4
5- Zone Assigned to Partition 5
6- Zone Assigned to Partition 6
7- Zone Assigned to Partition 7
8- Zone Assigned to Partition 8
Zone Parameters
Sections [0101] to [0196] represent
zones 1 to 96 respectively
Zone Definition
First Digit
Select one
only
Zone Options
Zone Partition
Assignment
Second Digit
Zone Options
Feature Select
[1] Auto Zone Shutdown
[2] Bypass Zone (Default)
[3] Stay Zone
[4] Force Zone
[5]
[6]
Zone Alarm Type
off
off
Audible Alarm (steady)
off
on
Audible Alarm (pulsed)
on
off
Silent Alarm
on
on
Generates only a report
[7] Intellizone
[8] Delay before transmission
Select one
or more
Press [ENTER]
4.1 ZONE NUMBERING
If PGM1 is defined as a smoke detector input (see section
10.6), the control panel will recognize it as input # 255.
12 REFERENCE & INSTALLATION MANUAL
Hardwired
Device A
Keypad
SN#: 1A000252
Keypad Zone
Control Panel
SN#:020000A2
1
2
Input Terminals
3 4 5 6
Detector A
SN#: 21000033
COMMUNICATION
Combus NETWORK
7
8
Input 2
SECTIONS [0001] TO [0096]
The Zone Numbering feature is used to individually assign each detection
device to any zone in the DigiplexNE system (see Figure 4-1). The Zone
Parameters define the type of zone, the zone's partition assignment and
how the control panel will react when an alarm occurs on that zone (see
section 4.3 to section 4.5).
• To assign an addressable PIR or door contact to the combus, program
the module’s serial number into the section corresponding to the desired
zone (i.e. program zone 34 in section [0034]).
• To assign a detection device connected to a module or control panel's
hardwired input terminal, program the module's or control panel's serial
number and the input number where the device is connected into the
section corresponding to the desired zone. See the Module
Programming Guide for details of its input numbers (input numbers not
required for keypad zones).
Figure 4-2: Zone Numbering
Hardwired
Device B
Detector A:
Hardwired Device A:
Hardwired Device B:
Hardwired Device C:
APR3-ZX8 Module
SN#: 34000041
1
2
Input Terminals
3 4 5 6
Zone#
1=
2=
3=
4=
7
Section#
[0001]
[0002]
[0003]
[0004]
Input 5
Hardwired
Device C
Serial#
21000033
1A000252
020000A2
34000041
Input#
N/A
N/A
002
005
8
4.1.1 Clearing a Zone’s Numbering
For LCD Keypads:
1) Enter a section number between [0001] to [0096].
2) Press [0] and then [ENTER] to save and exit.
For Grafica Keypads:
1) Enter a section number between [0001] to [0096].
2) Press [0] to clear the serial number
3) Use Grafica’s scroll keys, highlight the input number and then press
[0] to clear the data.
4) Press Grafica’s center action key (Save) to save and exit.
4.2 ZONE DOUBLING (ATZ)
SECTION [3033]: OPTION [8]
(Default = disabled) The ATZ feature is a software oriented feature that
enables two detection devices to be installed per hardwired input terminal
(section 2.15 on page 8 and see section 2.14 on page 8). Each detection
device has its own zone, displays its zone status on the keypad and sends
its own alarm codes. Fire Zones cannot be doubled.
Partition 3
Entry Delay 1 Timer: [3311]
Entry Delay 2 Timer: [3312]
Partition 7
Entry Delay 1 Timer: [3711]
Entry Delay 2 Timer: [3712]
Partition 4
Entry Delay 1 Timer: [3411]
Entry Delay 2 Timer: [3412]
Partition 8
Entry Delay 1 Timer: [3811]
Entry Delay 2 Timer: [3812]
Entry Delay zones are commonly used at the entry/exit points (i.e. front/
back door or garage). Using different Entry Delays is useful when one entry
point requires a longer delay than another.
These are the same timers used for Stay Delay zones (see section
4.3.14).
4.3.3 Follow Zones
SECTIONS [0101] TO [0196]: FIRST DIGIT = 3
If an armed Follow zone opens, the control panel generates an alarm. If an
armed Entry Delay zone (see section 4.3.2) opens before the Follow zone,
the control panel waits until the end of the Entry Delay before generating an
alarm. If more than one Entry Delay zone opens before the Follow zone,
the control panel waits until the end of the first Entry Delay before
generating an alarm. This feature is commonly used when a motion
detector is protecting the area occupied by the entry point keypad. This will
prevent the motion detector from causing an alarm when a user enters
through the entry point to disarm the system.
Input
Doubled Zone Input
Input 01
Input 13 (ATZ of Input 01)
Input 02
Input 14 (ATZ of Input 02)
Input 03
Input 15 (ATZ of Input 03)
Input 04
Input 16 (ATZ of Input 04)
4.3.4 Instant Zones
Input 05
Input 17 (ATZ of Input 05)
Input 06
Input 18 (ATZ of Input 06)
Input 07
Input 19 (ATZ of Input 07)
SECTIONS [0101] TO [0196]: FIRST DIGIT = 4
When an armed Instant zone opens, the control panel immediately
generates an alarm. Instant zones are commonly used for windows, patio
doors, skylights and other perimeter type zones.
Input 08
Input 20 (ATZ of Input 08)
Input 09 (DGP2-ZX4 Input 01)
Input 21 (ATZ of Input 09)
Input 10 (DGP2-ZX4 Input 02)
Input 22 (ATZ of Input 10)
Input 11 (DGP2-ZX4 Input 03)
Input 23 (ATZ of Input 11)
Input 12 (DGP2-ZX4 Input 04)
Input 24 (ATZ of Input 12)
4.3 ZONE DEFINITIONS
The 16 zone definitions from Figure 4-1 on page 12 are described below.
When an alarm occurs, the control panel can send a report, activate the bell
output and display the alarm in the Alarm Memory.
4.3.5 24Hr Buzzer Zones
SECTIONS [0101] TO [0196]: FIRST DIGIT = 5
Whenever a 24Hr Buzzer zone opens, whether the zone is armed or
disarmed, the control panel activates the keypad buzzer to indicate that the
zone was breached. The control panel will report the alarm, but will not
enable the bell/siren output. Enter any valid access code on the keypad to
stop the buzzer.
The keypads must be assigned to the same partition as the
24Hr Buzzer zone or the buzzer will not activate. UL Note: Not
to be used for perimeter protection.
4.3.6 24Hr Burglary Zones
4.3.1 Zone Disabled
SECTIONS [0101] TO [0196]: FIRST DIGIT = 0
Disables the corresponding zone. Zones are disabled by default.
4.3.2 Entry Delays 1 and 2
SECTIONS [0101] TO [0196]: FIRST DIGIT = 1 AND 2
(Default Entry Delay 1= 030, Entry Delay 2 = 060) When an armed zone
defined as an Entry Delay opens, the control panel will not generate an
alarm until the Entry Delay Timer elapses. A zone defined as Entry Delay 1
follows the Entry Delay 1 Timer of its assigned partition. Likewise, a zone
defined as Entry Delay 2 follows the Entry Delay 2 Timer of its assigned
partition.
For example, if zone 1 is assigned to Partition 5 and is defined as Entry
Delay 1, the timer follows the amount programmed in [3511].
Each partition includes two Entry Delay Timers. To program an Entry Delay
Timer, key in the desired 3-digit delay value (001 to 255 seconds) into the
corresponding section.
Partition 1
Entry Delay 1 Timer: [3111]
Entry Delay 2 Timer: [3112]
Partition 5
Entry Delay 1 Timer: [3511]
Entry Delay 2 Timer: [3512]
Partition 2
Entry Delay 1 Timer: [3211]
Entry Delay 2 Timer: [3212]
Partition 6
Entry Delay 1 Timer: [3611]
Entry Delay 2 Timer: [3612]
SECTIONS [0101] TO [0196]: FIRST DIGIT = 6
When a 24Hr Burglary zone opens, whether the system is armed or
disarmed, the control panel will immediately generate a burglary alarm.
4.3.7 24Hr Hold-up Zones
SECTIONS [0101] TO [0196]: FIRST DIGIT = 7
When a 24Hr Hold-up zone opens, whether it is armed or disarmed, the
control panel will immediately generate an alarm. The SIA FSK reporting
format includes specific codes to identify the alarm as a Hold-up Alarm.
4.3.8 24Hr Gas Zones*
SECTIONS [0101] TO [0196]: FIRST DIGIT = 8
When a 24Hr Gas zone opens, whether it is armed or disarmed, the control
panel will immediately generate an alarm. The SIA FSK reporting format
includes specific codes to identify the alarm as a Gas Alarm.
4.3.9 24Hr Heat Zones**
SECTIONS [0101] TO [0196]: FIRST DIGIT = 9
When a 24Hr Heat zone opens, whether it is armed or disarmed, the control
panel will immediately generate an alarm. The SIA FSK reporting format
includes specific codes to identify the alarm as a Heat Alarm.
** UL Note: UL Listed compatible devices shall be used for UL systems. For
UL Listed systems, this type of zone shall be programmed as a pulsing Fire
alarm.
DIGIPLEXNE CONTROL PANEL 13
4.3.10 24Hr Water Zones*
4.3.13 Standard 24Hr Fire Zone
SECTIONS [0101] TO [0196]: FIRST DIGIT = A
When a 24Hr Water zone opens, whether it is armed or disarmed, the
control panel will immediately generate an alarm. The SIA FSK reporting
format includes specific codes to identify the alarm as a Water Alarm.
SECTIONS [0101] TO [0196]: FIRST DIGIT = D
A zone programmed as Fire becomes normally open (will not function as
normally closed) and requires an EOL resistor.
When a Standard 24Hr Fire Zone triggers, the control panel can:
• send a Zone Alarm report code (see section 8.2.1 on page 24).
• send a Fire Loop Trouble Report (see section 8.2.11 on page 25) if a
tamper/wiring fault occurs on a Fire Zone. A “Zone Fault Trouble” will
also appear in the keypad's Trouble Display.
• generate a Fire alarm, which is always audible, regardless of other
settings. Fire alarms generate an intermittent signal (see Figure 4-4).
4.3.11 24Hr Freeze Zones*
SECTIONS [0101] TO [0196]: FIRST DIGIT = B
When a 24Hr Freeze zone opens, whether it is armed or disarmed, the
control panel will immediately generate an alarm. The SIA FSK reporting
format includes specific codes to identify the alarm as a Freeze Alarm.
* UL Note: UL Listed compatible devices shall be used for UL systems. For
UL Listed systems, this type of zone shall be programmed as a silent auxiliary
alarm.
Figure 4-4: Bell/Siren Output During Fire Alarm
4.3.12 Delayed 24Hr Fire Zone (Not to be used with UL Listed systems)
SECTIONS [0101] TO [0196]: FIRST DIGIT = C
The Delayed 24Hr Fire Zone definition from Figure 4-3: on page 14 is
commonly used in residential homes where a smoke detector often
generates false alarms (i.e. cigarette smoke, burning bread, etc.). A zone
programmed as Fire becomes normally open (will not function as normally
closed) and requires an EOL resistor.
The keypads must be assigned to the same partition as the
Delayed 24Hr Fire zone for the buzzer to activate.
Figure 4-3: Delayed 24Hr Fire Zone
Delayed Fire Zone
Triggered
Activate bell/siren output & delay
report transmission for 30 seconds.
4.3.14 Stay Delay Zone
SECTIONS [0101] TO [0196]: FIRST DIGIT = E AND F
When a Stay Delay zone is armed using the Regular or Force arming
methods, the control panel processes the zone as an Instant zone (see
section 4.3.4). When a Stay Delay zone is armed using the Stay or Instant
arming methods and the zone is triggered, the control panel will not
generate an alarm until the programmed Stay Delay elapses. A zone
defined as Stay Delay 1 follows the Entry Delay 1 Timer of its assigned
partition. Likewise, a zone defined as Stay Delay 2 follows the Entry Delay
2 Timer of its assigned partition. To program the Entry Delay Timers, refer
to Entry Delays 1 and 2 on page 13.
For example, if zone 1 in Partition 5 is defined as Stay Delay 1, the timer
will follow the amount programmed in [3511].
4.4 ZONE PARTITION ASSIGNMENT
Has the zone
closed within
30 seconds?
Yes
SECTIONS [0101] TO [0196]: SECOND DIGIT = 1 TO 8
A control panel can be divided into eight completely independent systems
(see section 11.9 on page 32). Assign each zone to one partition (see
Figure 4-1 on page 12).
No
4.5 ZONE OPTIONS
Has a 2nd
Delayed Fire
Zone opened in
30 sec.?
Yes
No
Any key on
keypad pressed
within 30
seconds?
No
Yes
Yes
Bell/siren silenced.
Delay report
transmission an additional 90 sec.
No
Problem
corrected?
Yes
END
Alarm Disabled
14 REFERENCE & INSTALLATION MANUAL
Latch alarm and transmit
report code as described
in the section "Standard
24Hr. Fire Zone".
The zone options from Figure 4-1 on page 12 are described below.
4.5.1 Auto Zone Shutdown
SECTIONS [0101] TO [0196]: OPTION [1]
(Default = 000) When option [1] is disabled, the control panel generates an
alarm when an armed zone is breached even if the same zone opens
repeatedly during the same alarm, which may cause several reportings and
further activation of the bell output. When option [1] is enabled, the control
panel will stop regenerating alarms on the zone during the same armed
period once the Auto Zone Shutdown Limit is reached. The Auto Zone
Shutdown Limit resets every time the system is armed. To program the
Auto Zone Shutdown Limit, key in the desired 3-digit counter (000 to 255)
into section corresponding to the desired partition (000 = disabled):
Partition 1: [3114]
Partition 5: [3514]
Partition 2: [3214]
Partition 6: [3614]
Partition 3: [3314]
Partition 7: [3714]
Partition 4: [3414]
Partition 8: [3814]
4.5.2 Bypass Zones
SECTIONS [0101] TO [0196]: OPTION [2]
Only zones with option [2] enabled can be Manually Bypassed (see section
15.7). Fire Zones cannot be bypassed. Default = enabled.
4.5.3 Stay Zones
Set the Input Speed (001 to 255 X 30ms, default = 600msec.):
SECTIONS [0101] TO [0196]: OPTION [3]
Only zones with option [3] enabled will be bypassed when the partition is
Stay Armed (see section 15.2) or Instant Armed (see section 15.3). All other
zones will remain activated. Fire Zones cannot be set as Stay Zones.
Section Input
Section
[0961]
Input 01
[0973]
Input 13 (ATZ of Input 01)
[0962]
Input 02
[0974]
Input 14 (ATZ of Input 02)
4.5.4 Force Zones (Not to be used with UL Listed systems)
[0963]
Input 03
[0975]
Input 15 (ATZ of Input 03)
SECTIONS [0101] TO [0196]: OPTION [4]
Only zones with option [4] enabled can be bypassed when the partition is
Force armed (see section 15.4). Fire Zones cannot be Force Zones.
[0964]
Input 04
[0976]
Input 16 (ATZ of Input 04)
[0965]
Input 05
[0977]
Input 17 (ATZ of Input 05)
[0966]
Input 06
[0978]
Input 18 (ATZ of Input 06)
[0967]
Input 07
[0979]
Input 19 (ATZ of Input 07)
[0968]
Input 08
[0980]
Input 20 (ATZ of Input 08)
4.5.5 Alarm Types
SECTIONS [0101]
TO
[0196]: OPTIONS [5] & [6]
Option Feature
[5]
Description
[6]
sends the report code and activates the bell
output
sends the report code and pulses the bell output
ON OFF Pulsed Alarm
(see Figure 4-4 on page 14)
sends the report code, but the bell output is not
OFF ON Silent Alarm
activated. Partition must be disarmed.
sends the report code. Disarming is not required.
ON ON Report Only
Fire Zones cannot be Report Only.
OFF OFF Steady Alarm
4.5.6 Intellizone*
SECTIONS [0101] TO [0196]: OPTION [7]
(Default = 010) If an alarm condition occurs on a zone with option [7]
enabled, the control panel triggers the Intellizone Delay and seeks
confirmation of the alarm situation before generating an alarm. Fire Zones
cannot be set as Intellizones. An alarm will only be generated if one of the
following conditions occurs during the Intellizone Delay:
1) An alarm occurs on another zone defined as Intellizone.
2) The zone in alarm restores and reoccurs.
3) The zone stays in alarm for the entire Intellizone Delay.
Key in the desired 3-digit delay value (010 to 255 seconds) into the section
corresponding to the desired partition (000 = 10 seconds):
Partition 1: [3110] Partition 3: [3310] Partition 5: [3510] Partition 7: [3710]
Partition 2: [3210] Partition 4: [3410] Partition 6: [3610] Partition 8: [3810]
* UL Note: For UL Listed systems, the detection pattern of both zones shall
be installed so that each zone has the capability of protecting the area alone.
4.5.7 Delay Before Alarm Transmission
SECTIONS [0101] TO [0196]: OPTION [8]
(Default = 000) When an alarm condition occurs on a zone with option [8]
enabled, the control panel activates the bell output, but will not report the
alarm to the Monitoring Station until the end of the Alarm Transmission
Delay. During this period, disarming the system cancels any report
originating from this zone. To program the Alarm Transmission Delay, key in
the desired value (000 to 255 seconds, 000 = instant) into section [3055].
This feature is commonly used with Entry Delay zones to reduce false
alarms created by new users who may not disarm the system in time.
Set the Input Speeds for the optional 4-Zone Hardwire Module, DGP2-ZX4:
Section Input
[0969]
Input 09 (DGP2-ZX4 Input 01)
[0970]
Input 10 (DGP2-ZX4 Input 02)
[0971]
Input 11 (DGP2-ZX4 Input 03)
[0972]
Input 12 (DGP2-ZX4 Input 04)
[0981]
Input 21 (ATZ of DGP2-ZX4 Input 01)
[0982]
Input 22 (ATZ of DGP2-ZX4 Input 02)
[0983]
Input 23 (ATZ of DGP2-ZX4 Input 03)
[0984]
Input 24 (ATZ of DGP2-ZX4 Input 04)
4.7 EOL ON HARDWIRE ZONES
SECTION [3033]: OPTION [7]
(Default = disabled) If detection devices connected to hardwired input
terminals use 1kΩ end of line resistors, enable option [7] in section [3033].
For details on using EOL resistors, refer to Addressable Zone Connections
on page 7 and Double Zone Connections on page 8.
4.8 KEYPAD NUMBERING
SECTIONS [2801] TO [2832]
Keypad Numbering is only used to identify the keypad in the event buffer.
When Keypad Numbering is not used, the event buffer will then display any
events pertaining to any keypad as Keypad 00. When Keypad Numbering is
used, each keypad is identified by a specific number. The keypad is
assigned to a Keypad Number from 1 to 32 through the keypad's serial
number in sections [2801] to [2832]. Enter the 8-digit serial keypad serial
number in the desired section.
4.6 INPUT SPEED
(001 to 255 X 30msec, default: 600ms)
The Input Speed defines how quickly the control panel responds to an open
zone detected on any hardwired input terminal (does not apply to
addressable motion detectors and door contacts). All other zone definitions
and options do not come into effect until the Input Speed elapses. The
control panel will not display and/or respond to an open zone until the Input
Speed elapses to prevent glitches from causing an alarm or unnecessary
reporting.
For example, if an armed zone with an Input Speed of 600ms opens and
closes in less than 600ms, the control panel will not respond (i.e. no
reporting, no alarm and no display on the keypad).
DIGIPLEXNE CONTROL PANEL 15
5
KEYSWITCH PROGRAMMING
The DigiplexNE control panel can support up to 32 keyswitch zones in addition to the 96 standard zones. A keyswitch allows a user to arm or disarm a
system by pressing a key or by toggling a keyswitch. A keyswitch can also be used to generate a Utility Key event which can then be used to activate or
deactivate PGM outputs connected to the DigiplexNE system. The keyswitches are connected to the hardwired input terminals of either the control panel,
zone expansion modules or the keypad. For installation instructions, see section 2.9 on page 4. Keyswitches must be programmed as described in this
section (see Figure 5-1). UL Note: Keyswitches are not to be used in UL Listed systems.
Figure 5-1: Keyswitch Programming
Press & hold the
[0] key
Keyswitch Definitions
[0] Disabled (default)
[1] Momentary Keyswitch
[2] Maintained Keyswitch
[3] Generates a Utility Key Event on Open
[4] Generates a Utility Key Event on Open & Close
Enter your
[INSTALLER CODE]
Enter 4-digit
[SECTION]
Select one
only
Keyswitch Parameters
Sections [0601] to [0632] represent
keyswitches 1 to 32 respectively
Keyswitch Numbering
Sections [0501] to [0532] represent
keyswitches 1 to 32 respectively
Keyswitch Definition
First Digit
Enter the module’s 8-digit
[SERIAL NUMBER] where the
keyswitch is installed
Select one
only
Keyswitch Partition
Assignment
Second Digit
Enter the 3-digit [INPUT
NUMBER] where the
keyswitch is connected
Keyswitch Options
Feature Select
Set
options
Keyswitch Partition Assignment
[0] Not assigned to partition(s) (default)
[1] Assigned to partition 1
[2] Assigned to partition 2
[3] Assigned to partition 3
[4] Assigned to partition 4
[5] Assigned to partition 5
[6] Assigned to partition 6
[7] Assigned to partition 7
[8] Assigned to partition 8
Keyswitch Options
Default = All OFF
[1] to [3] = Future Use
[4] Stay/Instant Disarm
[5] Arm Only
[6] Stay Arming*
[7] Force Arming*
[8] Instant Arming*
* Select one only; if all are OFF, defaults to regular
arming.
Press [ENTER]
5.1 KEYSWITCH NUMBERING
5.2 KEYSWITCH DEFINITIONS
SECTIONS [0501] TO [0532]
Keyswitch Numbering allows you to assign any hardwired input in the
system to any of the 32 keyswitch zones in the control panel. It identifies
where the keyswitch is connected and which keyswitch zone is assigned to
the keyswitch (see Figure 5-2).
Keyswitch Definitions determine how the control panel reacts when a
keyswitch is activated.
Figure 5-2: Example of Keyswitch Numbering
5.2.1 Keyswitch Disabled
SECTIONS [0601] TO [0632]: FIRST
Disables keyswitch input.
DIGIT
=0
5.2.2 Momentary Keyswitch
Control Panel
SN#: 020000A2
2
Input Terminals
3 4 5 6 7
8
Zone Expansion Module
SN#: 34000041
Input 1
1
COMMUNICATION
CombusNETWORK
1
2
Input Terminals
3 4 5 6
Section
[0501]
[0502]
[0503]
8
Keyswitch C
Keyswitch B
Keyswitch
Zone #
Keyswitch A:
1=
Keyswitch B:
2=
Keyswitch C:
3=
7
Input 6
Input 2
Keyswitch A
Serial#
020000A2
34000041
34000041
16 REFERENCE & INSTALLATION MANUAL
Input#
001
002
006
SECTIONS [0601] TO [0632]: FIRST DIGIT = 1
To arm a partition using the Momentary Keyswitch, turn on the keyswitch for
approximately three seconds then turn it off. Repeating this sequence will
disarm the system. The selected Keyswitch Option (see section 5.4)
determines the type of arming.
5.2.3 Maintained Keyswitch
SECTIONS [0601] TO [0632]: FIRST DIGIT = 2
To arm a partition using the Maintained Keyswitch, turn the switch from the
ON to the OFF position. To disarm a partition set the keyswitch in the ON
position. The selected Keyswitch Option (see section 5.4) determines the
type of arming. If the keyswitch’s Arm Only option is enabled, the control
panel will not perform any action when the switch is in the on position.
5.2.4 Generates a Utility Key Event on Open
5.4.5 Force Arming (Keyswitch)
SECTIONS [0601] TO [0632]: FIRST DIGIT = 3
When option [3] is enabled, a Utility Key Event will be generated whenever
the keyswitch input is opened (see Table 14 on page 51). This option can
be used to activate or deactivate one or more of DigiplexNE’s PGM outputs.
When a keyswitch is defined with the Generate a Utility Key Event on Open
option, the Keyswitch Partition Assignment and Keyswitch Options are
disabled. To program a Keyswitch to generate a Utility Key Event:
SECTIONS [0601] TO [0632]: OPTION [7]
Activating the keyswitch will arm the selected partition bypassing any open
zones defined as Force Zones (see section 4.5.4) at the time of arming. For
more information on Force Arming, refer to section 15.4.
1)
2)
Program the Activation Event of a PGM output with the Utility Key
Event corresponding to the desired keyswitch (see PGM
Programming Table in the Programming Guide: Event Group 048).
Enable option [3] in the section corresponding to the desired
keyswitch.
5.4.6 Instant Arming (Keyswitch)
SECTIONS [0601] TO [0632]: OPTION [8]
This option is identical to Stay Arming except that all armed zones will
become Instant Zones (see section 4.3.4). For more information on Instant
Arming, refer to section 15.3.
Only one of the arming options (Stay, Force, Instant and Regular)
can be selected.
5.2.5 Generates a Utility Key Event on Open and Close
SECTIONS [0601] TO [0632]: FIRST DIGIT = 4
When option [4] is enabled, a Utility Key Event will be generated whenever
the keyswitch input is opened and closed. As a result, the Utility Key Events
increase from 32 to 64 events when option [4] is enabled; one event for
each state (open and closed). See Table 14 on page 51.
This option can be used to activate or deactivate one or more of
DigiplexNE’s PGM outputs. When a keyswitch is defined with the Generate
a Utility Key Event on Open and Close option, the Keyswitch Partition
Assignment and Keyswitch Options are disabled. To program a Keyswitch
to generate a Utility Key Event:
1)
2)
Program the Activation Event of a PGM output with the Utility Key
Event corresponding to the desired keyswitch (see PGM
Programming Table in the Programming Guide: Event Group 048).
Enable option [4] in the section corresponding to the desired
keyswitch.
5.3 KEYSWITCH PARTITION ASSIGNMENT
SECTIONS [0601] TO [0632]: SECOND DIGIT = 1 TO 8
The control panel provides the option of partitioning the security system into
eight completely independent systems. Therefore, each keyswitch must be
assigned to one partition as shown in Figure 5-1 on page 16. For details on
Partitioning, see section 11.9 on page 32.
5.4 KEYSWITCH OPTIONS
Each keyswitch zone can be programmed with one or more of the options
below as shown in Figure 5-1 on page 16.
5.4.1 Stay/Instant Disarm Option (Keyswitch)
SECTIONS [0601] TO [0632]: OPTION [4]
When option [4] is enabled, the keyswitch can only disarm assigned Stay or
Instant Armed partitions. The Arm Only Option (see section 5.4.2) must be
disabled for this feature to function. When option [4] is disabled, the
keyswitch can disarm partitions armed using any arming method.
5.4.2 Arm Only (Keyswitch)
SECTIONS [0601] TO [0632]: OPTION [5]
When option [5] is enabled, the keyswitch can arm assigned partitions, but
cannot disarm any partitions. The type of arming is determined by the other
Keyswitch Options selected.
5.4.3 Regular Arming (Keyswitch)
SECTIONS [0601] TO [0632]: OPTION [6] TO [8]
When options [6] to [8] are disabled, the keyswitch arming option will
default to Regular Arming (see section 15.1).
5.4.4 Stay Arming (Keyswitch)
SECTIONS [0601] TO [0632]: OPTION [6]
Activating the keyswitch will bypass any zones defined as Stay Zones (see
section 4.5.3) in the selected partition. All other zones will remain activated.
For more information on Stay Arming, refer to section 15.2.
DIGIPLEXNE CONTROL PANEL 17
6
ARMING AND DISARMING OPTIONS
6.1 ARMING FOLLOWS PARTITION
6.4 RESTRICT ARMING ON AC FAILURE
(Default = disabled) A partition can be set to follow the arming and
disarming status of one or more partitions. If a partition is set to follow more
than one partition, the partition will arm when all the selected partitions are
armed. However, the partition will disarm as soon as one of the selected
partitions is disarmed.
For example, if options [2] and [3] are ON in section [3121], Partition 1 will
automatically arm whenever partitions 2 and 3 are armed. Partition 1 will
disarm when either partition 2 or partition 3 is disarmed.
SECTION [3035]: OPTION [1]
(Default = disabled) When option [1] is enabled, the control panel can
prevent arming if it detects a loss of AC power. Partitions will not arm until
power is restored.
Partition 1: [3121]
Partition 1 arms & disarms with:
Option [1] =
N/A
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 5: [3521]
Partition 5 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
N/A
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 2: [3221]
Partition 2 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
N/A
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 6: [3621]
Partition 6 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
N/A
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 3: [3321]
Partition 3 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
N/A
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 7: [3721]
Partition 7 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
N/A
Option [8] =
Partition 8
Partition 4: [3421]
Partition 4 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
N/A
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
Partition 8
Partition 8: [3821]
Partition 8 arms & disarms with:
Option [1] =
Partition 1
Option [2] =
Partition 2
Option [3] =
Partition 3
Option [4] =
Partition 4
Option [5] =
Partition 5
Option [6] =
Partition 6
Option [7] =
Partition 7
Option [8] =
N/A
6.2 RESTRICT ARMING ON SUPERVISION LOSS
SECTION [3034]: OPTION [4]
(Default = disabled) When option [4] is enabled, the control panel can
restrict arming if it receives a supervision loss signal from the Omnia
433MHz Wireless System OMN-RCV3 (see section 7.3). Partitions will not
arm until all supervision loss trouble conditions are corrected.
6.3 RESTRICT ARMING ON TAMPER
SECTION [3034]: OPTION [8]
(Default = disabled) When option [8] is enabled, the control panel prevents
arming if it detects a tamper on a zone or module (see section 7.5).
Partitions will not arm until the Installer Code is entered and tamper trouble
conditions are corrected.
18 REFERENCE & INSTALLATION MANUAL
6.5 RESTRICT ARMING ON BATTERY FAILURE
SECTION [3035]: OPTION [2]
(Default = disabled) When option [2] is enabled, the control panel prevents
arming if it detects a battery loss or if the battery voltage is less than 10.5V.
The control panel will not arm a partition until all battery trouble conditions
are corrected.
6.6 RESTRICT ARMING ON BELL OR AUXILIARY FAILURE
SECTION [3035]: OPTION [3]
(Default = disabled) When option [3] is enabled, the control panel can
prevent arming if it detects that:
• the bell or siren is disconnected
• the Bell Output has exceeded its current limits
• the Auxiliary Outputs have exceeded their current limits
The control panel will not arm any partition until all bell or auxiliary trouble
conditions are corrected.
6.7 RESTRICT ARMING ON TLM FAILURE
SECTION [3035]: OPTION [4]
(Default = disabled) When option [4] is enabled, the control panel can
prevent arming if it is unable to access the telephone line. The control panel
will not arm any partition until all TLM trouble conditions are corrected.
6.8 RESTRICT ARMING ON MODULE TROUBLES
SECTION [3035]: OPTION [5]
(Default = disabled) When option [5] is enabled, the control panel will
monitor the same Restrict Arming options selected for the control panel
(battery, tamper, supervision, AC, bell, auxiliary and/or TLM failures) for the
modules connected to the combus. The control panel will prevent arming if
the control panel detects the equivalent trouble condition occurring on a
module.
For example, if options [1], [2] and [5] are ON in section [3035], the control
panel prevents arming if it detects an AC or battery failure on the control
panel or on a module connected to the combus.
6.9 TIMED AUTO-ARMING
(Default = disabled) When this option is enabled, the control panel arms the
selected partition every day at the time set by the Auto-Arm Timer (see
section 6.9.1). A 60-second Exit Delay triggers before the partition arms,
but Auto-Arming can be cancelled by entering a valid access code. The
Auto-Arming Option sets the arming method (see section 6.11). If zones are
open when a partition is Auto-Armed, the control panel arms the partition
and considers all open zones as temporarily bypassed (except 24hr.
zones).
When the partition Auto-Arms, the control panel transmits the Auto-Arming
report code programmed in section [3910]. Whether the partition was
successfully armed or not, the control panel will always transmit the Late to
Close report code programmed in section [3912]. Enable option [1] in the
desired section:
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
6.9.1 Auto-Arm Timer
When Timed Auto-Arming is enabled (see section 6.9), the control panel
will attempt to arm the system at the time set by the Auto-Arm Timer.
For example, to Auto-Arm partition 2 everyday at 6:15PM, enable option [1]
in section [3222] (Timed Auto-Arming) and enter 18:15 in section [3201].
Enter the time when the partition should arm in the desired section:
Partition 1: [3101] Partition 3: [3301] Partition 5: [3501] Partition 7: [3701]
Partition 2: [3201] Partition 4: [3401] Partition 6: [3601] Partition 8: [3801]
6.10 NO MOVEMENT AUTO-ARMING
(Default = disabled) If no movement occurs in a partition for the period
specified by the No Movement Timer (see section 6.10.1), the control panel
will automatically arm that partition. The Auto-Arming Option determines
the arming method (see section 6.11). The control panel will transmit the No
Movement report code programmed in section [3913] upon arming.
Whether the partition was successfully armed or not, the control panel will
always transmit the Late to Close report code [3912]. Enable option [2] in
the desired section:
Partition 1: [3123] Option [8]
Partition 5: [3523] Option [8]
Partition 2: [3223] Option [8]
Partition 6: [3623] Option [8]
Partition 3: [3323] Option [8]
Partition 7: [3723] Option [8]
Partition 4: [3423] Option [8]
Partition 8: [3823] Option [8]
6.14 FOLLOW ZONE SWITCHES TO ENTRY DELAY 2
(Default = enabled) When option [8] is enabled and an Entry Delay zone is
bypassed, an armed Follow Zone (see section 4.3.3) that opens without an
Entry Delay being triggered will switch to the partition’s Entry Delay 2.
For example, zone 1 is an Entry Delay and zone 2 is a Follow zone
protecting the area where the keypad is installed. The partition is armed,
but zone 1 is bypassed. When option [8] is enabled, zone 2 will trigger Entry
Delay 2 instead of an alarm when the user approaches the keypad to
disarm the partition.
Enable option [8] in the desired section:
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
6.10.1 No Movement Timer
(Default = 000) If No Movement Auto-Arming is enabled (see section 6.10),
the control panel will attempt to arm the system if no movement has
occurred for the period specified by the No Movement Timer. Select the
section corresponding to the desired partition and program the time without
movement necessary before the control panel will arm and/or send the No
Movement report code. If No Movement Auto-Arming is disabled, the
control panel can still send the No Movement report code.
For example, to arm partition 1 when no movement occurs for 4 hours,
enable option [2] in section [3122] (No Movement Auto-Arm for partition 1)
and enter 016 (16 x 15min. = 240min. = 4 hours) in section [3107].
Enter the time period (001 to 255 x 15 minutes, 000 = disabled) when the
partition should arm in the desired section:
6.15 ONE-TOUCH FEATURES
(Default = disabled) The One-touch Features can arm or disarm a partition,
access Bypass Programming, or display the Event Buffer by pressing and
holding a specific key for 2 seconds instead of entering an access code. If
the keypad is assigned to more than one partition, the feature must be
enabled in the corresponding partitions. Select the section corresponding to
the desired partition and enable or disable the desired options:
Partition 1: [3125] Partition 3: [3325] Partition 5: [3525] Partition 7: [3725]
Partition 2: [3225] Partition 4: [3425] Partition 6: [3625] Partition 8: [3825]
Option One-Touch Feature
One-Touch Key
[1]
Regular Arming (see section 15.1)
[ARM]
[STAY]
[2]
Stay Arming (see section 15.2)
Partition 1: [3107] Partition 3: [3307] Partition 5: [3507] Partition 7: [3707]
[3]
Instant Arming (see section 15.3)
[5]
Partition 2: [3207] Partition 4: [3407] Partition 6: [3607] Partition 8: [3807]
[4]
Force Arming (see section 15.4)
[FORCE]
[5]
Stay/Instant Disarming (see section 15.6)
[DISARM]
[6]
Bypass Programming (see section 15.7)
[BYP]
[7]
Event Record Display (see section 15.10)
6.11 AUTO-ARMING OPTIONS
(Default = disabled) When using the Auto-Arming Features (see section 6.9
and section 6.10), the control panel can Force Arm (see section 15.4) or
Stay Arm (see section 15.2) the partitions. To Auto-Arm using Stay Arming,
enable option [3] in the desired section:
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
6.12 SWITCH TO STAY ARMING
If no Entry Delay zones are opened and closed during the Exit Delay after
Regular Arming a partition, the control panel can switch from Regular
Arming to Stay Arming. Enable the option in the desired section:
Partition 1: [3121] Option [1]
Partition 5: [3521] Option [5]
Partition 2: [3221] Option [2]
Partition 6: [3621] Option [6]
Partition 3: [3321] Option [3]
Partition 7: [3721] Option [7]
Partition 4: [3421] Option [4]
Partition 8: [3821] Option [8]
[7]
6.16 EXIT DELAY
(Default = 060) The Exit Delay determines the amount of time a user has to
leave the protected area before the control panel arms the partition. The
Exit Delay applies to all zones in the partition, except 24Hr. Zones. Program
the Exit Delay from 001 to 255 seconds:
Partition 1: [3108] Partition 3: [3308] Partition 5: [3508] Partition 7: [3708]
Partition 2: [3208] Partition 4: [3408] Partition 6: [3608] Partition 8: [3808]
6.16.1 Exit Delay Termination
(Default = enabled) The control panel can reduce the Exit Delay to 7
seconds when an Entry Delay zone (see section 4.3.2) is opened and
closed during the Exit Delay.
For example, 15 sec. into a 45-sec. Exit Delay, an Entry Delay zone opens
and closes. The remaining 30 sec. is reduced to 7 sec.
6.13 ALWAYS FORCE ARM WHEN REGULAR ARMING
(Default = Disabled) When option [8] is enabled for a particular partition, the
system will Force Arm that partition whenever Regular or Force arming is
activated. Stay and Instant arming are not affected by this feature.
DIGIPLEXNE CONTROL PANEL 19
Figure 6-1: Example of Exit Delay Termination
[6]
Remote Arming/
Disarming
Emits 1 squawk upon arming and 2 squawks
upon disarming with a remote control (using
the Omnia Wireless System, OMN-RCV3
(default = enabled) .
6.19 RING-BACK
Enable option [4] in the desired section:
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
6.16.2 No Exit Delay on Remote Arm
(Default = enabled) When a user arms by using a remote control from the
Omnia Wireless System (OMN-RCV3), the control panel will cancel the Exit
Delay and immediately arm the partition. Enable option [8] in the desired
section:
After disarming the system, the control panel can warn the user that there
was an alarm and that it may be dangerous to enter by having the keypad
beep 10 times and/or by squawking the bell 10 times. The user should
leave immediately and contact the Monitoring Station from a secure
location. Select the section that corresponds to the desired partition and
enable or disable the desired option (off = disabled):
Partition 1: [3124] Partition 3: [3324] Partition 5: [3524] Partition 7: [3724]
Partition 2: [3224] Partition 4: [3424] Partition 6: [3624] Partition 8: [3824]
Option Bell Squawk on:
[7]
Bell Ring-back
[8]
Keypad Ring-back
Partition 1: [3125] Partition 3: [3325] Partition 5: [3525] Partition 7: [3725]
Partition 2: [3225] Partition 4: [3425] Partition 6: [3625] Partition 8: [3825]
Description
Bell or siren emits 10 squawks
(default = disabled)
Keypad emits 10 beeps
(default = enabled)
6.17 KEYPAD LOCK-OUT FEATURE
6.20 MAXIMUM BYPASS ENTRIES
(Default = 000) If a consecutive number of invalid codes are entered into a
keypad, the control panel can be set to lockout access from all the keypads
in the partition for a specified period. Program the number of consecutive
invalid codes from 001 to 255 (000 = disabled) into the desired section:
(Default = 000) The Maximum Bypass Entries feature limits the number of
zones that can be bypassed in each partition.
For example, program section [3115] with 010. When in Bypass
Programming (see section 15.7), the control panel will not let the user
bypass more than 10 zones in partition 1.
Enter any value between 001 and 096 (000 = no limit).
Partition 1: [3105] Partition 3: [3305] Partition 5: [3505] Partition 7: [3705]
Partition 2: [3205] Partition 4: [3405] Partition 6: [3605] Partition 8: [3805]
(Default = 000) Program the duration of the keypad lockout from 001 to 255
minutes into the desired section. Programming 000 into these sections will
not lockout the keypad, the control panel will transmit the Keypad Lockout
report code programmed in section [3937].
Partition 1: [3106] Partition 3: [3306] Partition 5: [3506] Partition 7: [3706]
Partition 2: [3206] Partition 4: [3406] Partition 6: [3606] Partition 8: [3806]
6.18 BELL SQUAWK
The control panel can activate the bell output briefly causing the bell or
siren to squawk to alert users that a partition is being armed, disarmed or
that an Entry or Exit Delay was triggered. Enable or disable the desired
option (off = disabled):
Partition 1: [3124] Partition 3: [3324] Partition 5: [3524] Partition 7: [3724]
Partition 2: [3224] Partition 4: [3424] Partition 6: [3624] Partition 8: [3824]
Option Bell Squawk on:
[1]
Disarming
[2]
Arming
[3]
Auto-Arming
[4]
Exit Delay
[5]
Entry Delay
Description
Emits 2 squawks upon disarming
(default = disabled).
Emits 1 squawk upon arming
(default = disabled).
Emits 1 squawk every second for 60
seconds before Auto-Arming a partition.
Emits a series of 3 squawks every second
for 10 seconds before arming
(default = disabled).
Emits 1 squawk every second during the Exit
Delay. Emits a series of 3 squawks every
second during the final 10 seconds of the
Exit Delay (default = disabled).
Emits 1 squawk every second during the
Entry Delay (default = disabled).
20 REFERENCE & INSTALLATION MANUAL
Partition 1: [3115] Partition 3: [3315] Partition 5: [3515] Partition 7: [3715]
Partition 2: [3215] Partition 4: [3415] Partition 6: [3615] Partition 8: [3815]
6.21 DISPLAY “BYPASS” IF ARMED
SECTION [3033]: OPTION [5]
(Default = enabled) When option [5] is enabled, the keypads will not display
that zones have been bypassed while the system is armed.
7
ALARM OPTIONS
7.1 BELL/ALARM OUTPUT
(Default = only option [1] enabled) When an alarm condition is detected in a
partition, the control panel can toggle the on-board BELL output enabling
any bells or sirens connected to it. In section [3032] enable the option to
enable the bell output in the desired partition (off = disabled):
Partition 1: Option [1]
Partition 2: Option [2]
Partition 3: Option [3]
Partition 4: Option [4]
Partition 5: Option [5]
Partition 6: Option [6]
Partition 7: Option [7]
Partition 8: Option [8]
7.2 BELL CUT-OFF TIMER
(Default = 004) After an audible alarm, the bell or siren will stop once the
partition is disarmed or when the Bell Cut-Off Timer has elapsed. Enter any
value between 001 and 255 minutes:
Partition 1: [3113] Partition 3: [3313] Partition 5: [3513] Partition 7: [3713]
Partition 2: [3213] Partition 4: [3413] Partition 6: [3613] Partition 8: [3813]
7.2.1 No Bell Cut-Off on Fire Alarm
SECTION [3030]: OPTION [2]
(Default = disabled) The control panel can disable the Bell Cut-Off Timers
when alarms are generated from zones defined as Standard or Delayed
Fire Zones (see section 4.3). The BELL output will remain enabled until a
user disarms the partition in alarm.
When disarmed: Generates Trouble Only
The control panel displays Zone Fault in the Trouble Display
and transmits the defined report code (see section 8.2).
ON OFF
When armed: Follows Zone Alarm Type
The control panel follows the zone’s alarm type (see section
4.5.5 on page 15).
When disarmed: Generates Audible Alarm
The control panel displays Zone Fault in the Trouble Display,
transmits the defined report code (see section 8.2), and
ON ON generates an audible alarm.
When armed: Follows Zone Alarm Type
The control panel follows the zone’s alarm type (see section
4.5.5 on page 15).
7.3.1 Supervision Bypass Options
SECTION [3034]: OPTION [3]
(Default = disabled) With option [3] enabled in section [3034], the Wireless
Transmitter Supervision Options will follow the zone's bypass definition.
This means that the control panel will not perform any action if a
supervision loss occurs on a bypassed zone. With option [3] disabled, the
control panel will ignore the bypass definition and will follow the option set
in section 7.3 if a supervision loss occurs on a bypassed zone.
7.4 POLICE CODE TIMER
(Default = 000) The control panel re-verifies the zone status during an
alarm at a programmed rate once the Bell Cut-Off Timer and the Recycle
Delay elapse. If open zones remain, the control panel will regenerate the
alarm. Enter the number of times from 001 to 255 (000 = no limit) in one
armed period that the control panel will re-verify the zone status:
(Default = 000) If an alarm condition occurs on a zone, the control panel
generates an alarm and triggers the Police Code Timer. The Police Code
Timer requires confirmation of the alarm situation within the delay before
sending the Police Code programmed in [3934]. The Police Code will only
be sent if one of the following conditions occurs during the delay:
1) An alarm occurs on another zone.
2) The zone in alarm restores and reoccurs.
Key in the desired 3-digit delay value (001 to 255 minutes, 000 = disabled)
into the section corresponding to the desired partition:
Partition 1: [3117] Partition 3: [3317] Partition 5: [3517] Partition 7: [3717]
Partition 1: [3118] Partition 3: [3318] Partition 5: [3518] Partition 7: [3718]
Partition 2: [3217] Partition 4: [3417] Partition 6: [3617] Partition 8: [3817]
Partition 2: [3218] Partition 4: [3418] Partition 6: [3618] Partition 8: [3818]
7.2.3 Recycle Delay
7.5 TAMPER RECOGNITION OPTIONS
7.2.2 Recycle Alarm Rate
(Default = 000) The Recycle Delay is the amount of time the control panel
will wait after the Bell Cut-off occurs before re-verifying the zone status.
Program the Recycle Delay from 001 to 255 minutes (000 = disabled):
Partition 1: [3116] Partition 3: [3316] Partition 5: [3516] Partition 7: [3716]
Partition 2: [3216] Partition 4: [3416] Partition 6: [3616] Partition 8: [3816]
SECTION [3034]: OPTIONS [5] AND [6]
When the control panel detects a tamper or wire fault on a zone or on an
expansion module, the control panel can generate an alarm and/or trouble,
as shown in the table below, unless the Tamper Recognition Option is
disabled.
Option
7.3 WIRELESS TRANSMITTER SUPERVISION OPTIONS
SECTION [3034]: OPTIONS [1] AND [2]
When the control panel detects a Supervision Loss (wireless receiver no
longer receiving signals from a wireless transmitter), the control panel can
generate an alarm and/or trouble, as shown in the table below, unless the
Wireless Transmitter Supervision Option is disabled.
The Supervision feature must be enabled in the Omnia Wireless
System (OMN-RCV3) for this feature to function.
Option
[1]
[2]
Description
Disabled (Default):
Displays zone open on the keypads, but will not generate an
OFF OFF
alarm or trouble.
Not permitted on UL systems.
Generates Trouble Only (when armed or disarmed):
OFF ON The control panel displays Zone Fault in the Trouble Display
and transmits the defined report code (see section 8.2).
[5]
[6]
Description
Disabled (Default):
Displays zone open on the keypads, but will not generate an
alarm or trouble.
Not permitted on UL systems.
Generates Trouble Only (when armed or disarmed):
OFF ON The control panel displays Zone Fault in the Trouble Display and
transmits the defined report code (see section 8.2).
When disarmed: Generates Trouble Only
The control panel displays Zone Fault in the Trouble Display and
transmits the defined report code (see section 8.2).
ON OFF
When armed: Follows Zone Alarm Type
The control panel follows the zone’s alarm type (see section
4.5.5 on page 15).
When disarmed: Generates Audible Alarm
The control panel displays Zone Fault in the Trouble Display,
transmits the defined report code (see section 8.2), and
ON ON generates an audible alarm.
When armed: Follows Zone Alarm Type
The control panel follows the zone’s alarm type (see section
4.5.5 on page 15).
OFF OFF
DIGIPLEXNE CONTROL PANEL 21
7.5.1 Tamper Bypass Options
SECTION [3034]: OPTION [7]
(Default = enabled) With option [7] enabled in section [3034], the control
panel will ignore the zone’s bypass definition and will follow the option set in
section 7.5 if a tamper or wire fault occurs on a bypassed zone. With option
[7] disabled, Tamper Recognition follows the zone’s bypass definition. This
means that the control panel will not perform any action if a tamper or wire
fault occurs on a bypassed zone.
7.6 KEYPAD PANIC OPTIONS
(Default = disabled) The control panel can generate an alarm (audible, fire
or report only) by pressing the keypad Panic key(s). For LCD keypads, two
keys are pressed and held simultaneously for 2 seconds. For Grafica
keypads, the appropriate Panic key is pressed and held for 2 seconds.
Refer to the table below for the keypad Panic keys. In the section that
corresponds to the desired partition, enable or disable options [1] through
[6] as desired:
Partition 1: [3123] Partition 3: [3323] Partition 5: [3523] Partition 7: [3723]
Partition 2: [3223] Partition 4: [3423] Partition 6: [3623] Partition 8: [3823]
Option Feature
Press and Hold:
LCD keypads: Keys [1] and [3] simultaneously
[1]
Panic 1*
Grafica keypads: The
key
LCD keypads: Keys [4] and [6] simultaneously
[2]
Panic 2*
Grafica keypads: The
key
LCD keypads: Keys [7] and [9] simultaneously
[3]
Panic 3
Grafica keypads: The
key
Option Alarm Type
[4]
Panic 1:*
[5]
Panic 2:*
[6]
Panic 3:
= Audible
= Report Only
ON = Audible
OFF = Report Only
ON = Fire
OFF = Report Only
ON
OFF
REPORT ONLY
The keypad emits a single Confirmation Beep and transmits the appropriate
report code (see section 8.2.10).
AUDIBLE ALARM
The control panel activates the BELL output until a user cancels the alarm
with a valid User Access Code or when the Bell Cut-Off Timer elapses (see
section 7.2).
FIRE ALARM
Same as audible operation, except that the bell/siren output will be pulsed
as shown in Figure 4-4 on page 14.
* UL Note: For UL Listed systems, all emergency non-medical and auxiliary
panic alarms shall be report only.
22 REFERENCE & INSTALLATION MANUAL
8
EVENT REPORTING
Figure 8-1: Event Reporting
Dialing Enabled/Disabled
Section [3036]
Option [3]
Partition 1
Partition 2
Reporting Account Number 1
3 or 4 digits (0-F) in Section [3061]
Reporting Account Number 2
3 or 4 digits (0-F) in Section [3062]
Related Features
Delay Before Alarm Transmission: [3055]
Pager Format Delay Transmission: [3057]
Recent Closing Delay
Sections [3109], [3209], [3309], [3409],
[3509], [3609], [3709] and [3809]
Partition 3
Reporting Account Number 3
3 or 4 digits (0-F) in Section [3063]
Partition 4
Reporting Account Number 4
3 or 4 digits (0-F) in Section [3064]
Partition 5
Reporting Account Number 5
3 or 4 digits (0-F) in Section [3065]
Report Disarm Options
Option [7]: Sections [3123], [3223], [3323],
[3423], [3523], [3623], [3723] and [3823]
Partition 6
Reporting Account Number 6
3 or 4 digits (0-F) in Section [3066]
Report Zone Restore Options
Section [3037] Option [8]
Partition 7
Reporting Account Number 7
3 or 4 digits (0-F) in Section [3067]
Partition 8
Reporting Account Number 8
3 or 4 digits (0-F) in Section [3068]
Power Failure Report Delay: [3058]
Reporting Account Numbers
Central Station
Telephone Numbers
1 to 4 (32 digits)
Sections [3071] to [3074]
Dialing sequences for Arm/Disarm Report Codes
Partition 1 = [3127]
Partition 5 = [3527]
Partition 2 = [3227]
Partition 6 = [3627]
Partition 3 = [3327]
Partition 7 = [3727]
Partition 4 = [3427]
Partition 8 = [3827]
Event Call Direction
Defines to which Central
Station Telephone Number
each specific group of events
will be reported.
Dialing sequences for Alarm/Restore Report Codes
Partition 1 = [3128]
Partition 5 = [3528]
Partition 2 = [3228]
Partition 6 = [3628]
Partition 3 = [3328]
Partition 7 = [3728]
Partition 4 = [3428]
Partition 8 = [3828]
Dialing sequences for Tamper/Restore Report Codes
Partition 1 = [3129]
Partition 5 = [3529]
Partition 2 = [3229]
Partition 6 = [3629]
Partition 3 = [3329]
Partition 7 = [3729]
Partition 4 = [3429]
Partition 8 = [3829]
Dialing sequence for
Trouble/Restore Report Codes: [3080]
Dialing sequence for
System Special Report Codes: [3081]
Pulse
Reporting Formats
Section [3070]
First digit
= CSTN #1
Second digit =CSTN #2
Third digit
=CSTN #3
Fourth digit
=CSTN #4
CSTN = Central Station
Telephone Number
[0]
Ademco Slow
[1]
Silent Knight Fast
[2]
Sescoa
DTMF
(Tone)
[3]
Ademco Express
[7]
Pager
[6]
SIA FSK
[5]
Ademco Contact I.D.
Program 2-digit (00-FF)
report codes into:
Sections [0201] to [0296]
Sections [0701] to [0732]
Sections [0801] to [0832]
Sections [2001] to [2099]
Sections [2101] to [2199]
Sections [3900] to [3991]
Auto Test Report: [3040] and [3041]
Alternate Dial
Section [3037] Option [6]
[1] = Call Central Telephone 1
[2] = Call Central Telephone 2
[3] = Call Central Telephone 3
[4] = Call Central Telephone 4
[5] = Backup on Telephone 1
[6] = Backup on Telephone 6
[7] = Backup on Telephone 7
[8] = Backup on Telephone 8
For each section (dialing sequence)
enable up to 4 central station
telephone numbers and 1 backup
telephone number. The numbers are
dialed sequentially from 1 to 4
followed by the backup number. This
sequence will continue until each
number has been dialed at least
once.
Maximum Dialing Attempt
Section [3056]
Delay Between Dialing Attempts
Section [3054]
Sections [4030] to [4037]
Manual & Automatic programming of report codes, refer to:
1) Ademco Contact ID and SIA FSK under Reporting Formats
2) Auto Report Code Programming
DIGIPLEXNE CONTROL PANEL 23
8.1 REPORTING ENABLED
SECTION [3036]: OPTION [3]
(Default = disabled) With option [3] ON in section [3036], Event Reporting is
enabled. When an event (e.g. zone in alarm) occurs in the system, the
control panel verifies if a report code was programmed in the section
corresponding to the event. If a report code is programmed, the control panel
dials the Monitoring Station telephone number defined by the Event Call
Direction feature. When the Monitoring Station answers, the control panel
transmits the system account code, followed by the programmed report code.
8.2 REPORT CODES
A report code is a 2-digit or 1-digit hexadecimal value, consisting of digits from
0 to F. For a comprehensive list of the events and their relevant sections,
please refer to the DigiplexNE Programming Guide. Only the Ademco Slow,
Silent Knight, Sescoa and Pager Formats support 1-digit report codes.
When a specific event occurs, the control panel will send the programmed
report code to the Monitoring Station. The method of report code
transmission is defined by the following two items: Reporting Formats
(see section 8.7) and Event Call Direction (see section 8.8). These two
items define how and where the report codes are transmitted. If you are
using the Ademco CID or SIA formats, an Auto Report Code Programming
feature is available (see section 8.15). The following sub-sections provide a
brief description of the events that the control panel can report:
8.2.1 Zone Alarm and Alarm Restore Report Codes
SECTIONS [0201] TO [0296]: FIRST AND SECOND BRACKETS
A report code can be programmed for each of the 96 available zones. Each
section from [0201] to [0296] corresponds to a zone from 01 to 96. The first
set of 2 digits in the sections refer to the Alarm Report Codes that can be
sent to the Monitoring Station to identify which zones generated an alarm.
The second set of 2 digits in the sections refer to the Alarm Restore Report
Codes that can be sent to the Monitoring Station when a zone closes or
once the bell has cut-off after generating an alarm (see section 7.2). Also,
refer to Zone Restore Report Options in section 8.14.
8.2.2 Tamper and Tamper Restore Report Codes
SECTIONS [0201] TO [0296]: THIRD AND FOURTH BRACKETS
A report code can be programmed for each of the 96 available zones. Each
section from [0201] to [0296] corresponds to a zone from 01 to 96. The
third set of 2 digits refer to the Tamper Report Codes that can be sent to the
Monitoring Station to identify which zone experienced a tamper or wire
fault. If the Tamper Recognition Options (see section 7.5) are disabled, the
control panel will not report the occurrence of any tampers or wire faults.
The fourth set of 2 digits refer to the Tamper Restore Report Codes that can
be sent to the Monitoring Station to identify which zone was restored.
8.2.3 Keyswitch Arming
SECTIONS [0701] TO [0732]
A report code can be programmed for each of the 32 keyswitch zones.
Each section from [0701] to [0732] corresponds to a keyswitch from 1 to
32. When using a keyswitch to arm a partition, the control panel can send
the report code to the Monitoring Station identifying which keyswitch was
used. The control panel will not send report codes for keyswitches that are
defined with the PGM Activation definition.
8.2.4 Keyswitch Disarming
SECTIONS [0801] TO [0832]
A report code can be programmed for each of the 32 keyswitch zones. Each
section from [0801] to [0832] corresponds to a keyswitch from 1 to 32. When
a keyswitch is used to disarm a partition, the control panel can send the
report code to the Monitoring Station identifying which keyswitch was used.
The control panel can transmit the report codes every time a partition is
disarmed or only when it is disarmed following an alarm. Also, refer to Disarm
Reporting Options in section 8.13. The control panel will not send report
codes for keyswitches that are defined with the PGM Activation definition.
24 REFERENCE & INSTALLATION MANUAL
8.2.5 Access Codes Arming
SECTIONS [2001] TO [2099]
A report code can be programmed individually for each User Access Code
from 01 to 98 in sections [2001] to [2098]. User Access Codes from 99 to
999 use a common report code in section [2099]. When an access code is
used to arm a partition, the control panel can send the report code to the
Monitoring Station identifying which access code was used.
8.2.6 Access Codes Disarming
SECTIONS [2101] TO [2199]
A report code can be programmed individually for each User Access Code
from 01 to 98 in sections [2101] to [2198]. User Access Codes from 99 to
999 use a common report code programmed in section [2199]. When an
access code is used to disarm a partition, the control panel can send the
report code to the Monitoring Station identifying which access code was
used. The report code can be transmitted when a partition is disarmed or
only when disarmed following an alarm. Also, see section 8.13.
8.2.7 Special System Reporting Codes
When the system generates one of the following events, the control panel
can send the report code to the Monitoring Station identifying the event:
Section
Event
Description
[3900]
Cold Start
control panel re-starts after complete
shutdown (total power loss)
[3901]
Warm Start
control panel resets due to sudden
problem other than power loss
[3902]
Test Report
report generated automatically
(see section 8.12)
[3903] to [3904]
Future Use
[3905]
WinLoad Log Off
control panel ends communication with
WinLoad
[3906]
Installer In
installer enters programming mode
[3907]
Installer Out
installer exits programming mode
[3908] to [3909]
Future Use
8.2.8 Special Arming Report Codes
When the partition arms using a special arming feature, the control panel
can send the report code identifying how the system was armed.
Section
Event
Description
[3910]
Auto-Arming
when Auto-Arming (see section 6.9)
[3911]
PC Arming
system armed using WinLoad or NEware
software
[3912]
Late to Close
when Auto-Arming (see section 6.9)
[3913]
No Movement
when No Movement Auto-Arming
(see section 6.10)
[3914]
Partial Arming
when partitions are Stay, Instant or Force
Armed or armed with bypassed zones
[3915]
Quick Arming
partitions armed with a One-Touch Arming
feature (see section 6.15)
[3916]
Early to Close
partition armed before Arming Report
Schedule (see section 8.3.2)
[3917]
Late to Close
partition armed after Arming Report
Schedule (see section 8.3.2)
[3918]
Remote Arm
partition armed with the InTouch VoiceAssisted Arm/Disarm Module (APR3ADM2)
[3919]
Partition hasn’t been armed before the
Closing Delinquency programmed Closing Delinquency Timer
elapsed (see section 8.16).
8.2.9 Special Disarming Report Codes
When using one of the special disarming features listed below, the control
panel can send the report code to the Monitoring Station identifying how the
system was disarmed. The control panel can transmit the report codes
every time a partition is disarmed or only when it is disarmed following an
alarm. Also, refer to Disarm Reporting Options in section 8.13.
[3944]
Bell Output
bell output is disconnected or the current
is greater than or equal to 3A
[3945]
Clock Loss
panel time lost (see section 11.16)
[3946]
Fire Loop Trouble
tamper on a fire zone (see section 4.3)
[3947] TO [3949]
[3950]
Future Use
Bus Fault
a module was removed from the combus
[3951]
Module Tamper
tamper/wire fault on module (not a motion
detector) on the combus
Section
Event
Description
[3920]
Cancel Auto-Arm
partition disarms during the Auto-Arm’s
60-sec. delay (see section 6.9)
[3952]
ROM Check Error
on-board Read-Only Memory trouble
[3921]
Quick Disarm
partition disarms using One-Touch
Disarming feature (see section 6.15)
[3953]
Module TLM
TLM failure detected on Voice-Assisted
Arm/Disarm Module (APR3-ADM2)
[3922]
PC Disarm
system disarmed using WinLoad or
NEware software
[3954]
Module Fail to
Communicate
DGP2-DVAC failed to communicate with
the Monitoring Station
[3923]
PC Disarm after
Alarm
system disarmed using WinLoad or
NEware software after an alarm occurs
[3955]
Printer Fault
Printer Module detected an error
Module AC Failure no AC power detected on a module
[3924]
Cancel Alarm
indicates that an alarm was cancelled
even though the system was not armed
when the alarm occurred.
[3956]
[3957]
Module Battery
Failure
battery on a module is disconnected or the
battery voltage is low
[3925]
Future Use
Future Use
[3958]
The AUX output on a module has
exceeded current limits
[3926]
Early to Open
partition disarmed before Disarming
Schedule (see section 8.3.2)
Module Auxiliary
Failure
[3959]
Future Use
Future Use
the battery voltage is low on a wireless
transmitter
[3927]
[3928]
Late to Open
partition disarmed after Disarming
Schedule (see section 8.3.2)
[3960]
Wireless Transmitter Low Battery
[3961]
Remote Disarm
partition disarmed with InTouch VoiceAssisted Arm/Disarm Module (APR3ADM2)
Wireless Module
This report code is global unless using the
Supervision Failure Contact ID or SIA reporting formats
[3962] to [3964]
Future Use
[3965]
Fail to Com 1
Phone Number 1 failed to communicate*
8.2.10 Special Alarm Report Codes
[3966]
Fail to Com 2
Phone Number 2 failed to communicate*
When an alarm is generated, the control panel can send the report code to
the Monitoring Station identifying the type of alarm.
[3967]
Fail to Com 3
Phone Number 3 failed to communicate*
[3968]
Fail to Com 4
Phone Number 4 failed to communicate*
Section
Event
Description
[3930]
Emergency Panic
(non-medical)
the panic keys [1] and [3] were pressed
(see section 7.6)
[3931]
Auxiliary Panic
the panic keys [4] and [6] were pressed
(see section 7.6)
Section Event
Fire Panic
the panic keys [7] and [9] were pressed
(see section 7.6)
Section Event
[3932]
[3970]
TLM1 Restored
[3981]
Module Tamper Restored
Recent Closing
an alarm is generated within the Recent
Close Delay (see section 8.10)
[3971]
AC Restored
[3982]
ROM Check Error Restored
[3972]
Battery Restored
[3983]
Module TLM Restored
[3973]
Auxiliary Supply
Restored
[3984]
Module Fail to Communicate
Restored
[3974]
Bell Output Restored [3985]
Printer Fault Restored
[3975]
Clock Loss Restored [3986]
Module AC Failure Restored
[3976]
Fire Loop Restored
[3987]
Module Battery Restored
[3977]
Future Use
[3988]
Module Auxiliary Restored
[3978]
Future Use
[3989]
Future Use
[3979]
Future Use
[3990]
Wireless Transmitter Battery
Restored
[3980]
Bus Fault Restored
[3991]
Wireless Module Supervision
Restored
[3933]
[3934]
Police Code
Confirmation of an alarm condition
occurred during the Police Code Timer’s
delay (see section 7.4).
[3935]
Auto Zone
Shutdown
the control panel stops regenerating
alarms on a zone during the same armed
period (see section 4.5.1)
[3936]
[3937]
Duress
a Duress enabled access code is keyed in
(refer to the Digiplex/DigiplexNE LCD
Keypad Reference & Installation Manual)
Keypad Lockout
too many invalid codes entered
(see section 6.17)
* No “Fail to Communicate” for Pager telephone numbers
8.2.12 System Trouble Restore Codes
When a trouble described in sections [3940] to [3961] is corrected, the
control panel can send the report code to the Monitoring Station.
8.2.11 System Trouble Codes
When a trouble is detected, the control panel can send the report code to
the Monitoring Station identifying the type of trouble.
Section
Event
Description
[3940]
TLM1 Failure
TLM failure on main telephone line
[3941]
AC Failure
AC power not detected. Also, see Power
Fail Report Delay in section 8.11
[3942]
Battery Failure
battery is disconnected or the battery
voltage is less than or equal to 10.5V
Auxiliary Supply
the aux power supply’s current is greater
than or equal to 1.1A
[3943]
If the Telephone Line Monitoring (see section 9.1) is disabled,
the control panel will not transmit the TLM report code.
8.3 REPORT ARMING AND DISARMING
The following two features combine to identify when a partition should be
armed and disarmed and enable the control panel to communicate
deviations from the normal schedule to the Monitoring Station.
8.3.1 Enable Arming and Disarming Report Schedules
(Default = disabled) If the partition is armed or disarmed during times not
programmed in the Arming and Disarming Report Schedules (see section
8.3.2), the control panel will send the corresponding report code Early to
DIGIPLEXNE CONTROL PANEL 25
Close [3916], Late to Close [3917], Early to Open [3926] or Late to Open
[3927]. In the desired section enable options [5] and [6] to enable the
Arming and Disarming Report Schedules:
Partition 1: [3122] Partition 3: [3322] Partition 5: [3522] Partition 7: [3722]
Partition 2: [3222] Partition 4: [3422] Partition 6: [3622] Partition 8: [3822]
Option Feature
[5]
Arming Report Schedule
[6]
Disarming Report Schedule
the System Manager’s Manual) have the number of minutes programmed
in these sections added before and after the corresponding partition’s
schedule. This allows certain individuals more flexibility without modifying
all the Schedules.
For example, using Figure 8-2 in section 8.3.2 if 015 is programmed in
section [3104], users with Add Tolerance Windows to Schedules enabled
on their cards can disarm between 8:35 and 9:25 and can arm between
16:40 and 17:45 without the control panel sending the report codes.
Enter any value between 001 and 255 to determine Arming/Disarming
Schedule Tolerance Window in minutes.
Partition 1: [3104] Partition 3: [3304] Partition 5: [3504] Partition 7: [3704]
8.3.2 Arming and Disarming Report Schedules
Partition 2: [3204] Partition 4: [3404] Partition 6: [3604] Partition 8: [3804]
Arming and Disarming Report Schedules identify the days and times that a
partition should be armed and disarmed. Each partition includes an Arming
Report Schedule and a Disarming Report Schedule. Each schedule
consists of 2 programmable time periods called Intervals that determine the
time span and days when the partition should be armed or disarmed (see
Figure 8-2). To enable the schedules, refer to section 8.3.1.
Figure 8-2: Example of an Arming and a Disarming Report Schedule
The Arming/Disarming Schedule Tolerance Window applies to
the Arming and Disarming Report Schedules only (section
8.3.1 and section 8.3.2). The Arming/Disarming Schedule
Tolerance Window does not apply to Access Schedules
(section 13.6).
8.4 MONITORING STATION PHONE #
SECTIONS [3071] TO [3074]
The control panel can dial up to 4 different Monitoring Station telephone
numbers. Sections [3071] to [3074] represent Monitoring Station telephone
numbers 1 through 4. Enter any digit from 0 to 9 and any special keys or
functions (see Table 3) up to a maximum of 32 digits. Refer to Event Call
Direction in section 8.8 and Reporting Formats in section 8.7 for details on
how these telephone numbers are used.
Table 3: Special Telephone Number Keys
Function
LCD
*
[STAY]
#
[FORCE]
Switch to Tone Dialing (T)
Wait for second dial tone (W)
In the section that corresponds to the desired partition, program the Start
Time and End Time according to the 24-hour clock and enable the options
representing the desired Days. When option [8] is enabled, access is
permitted during the programmed holidays (see section 13.8).
Arming Report Schedule
Partition 1: [3102] Partition 3: [3302] Partition 5: [3502] Partition 7: [3702]
[ARM]
[DISARM]
Grafica
[#]
(Press the key until the
desired letter/symbol
appears)
4-second pause (P)
[BYP]
Insert
[MEM]
Delete
[TRBL]
—
Delete from cursor to end
[ACC]
Left action key (Clear)
—
8.5 ACCOUNT NUMBER
SECTIONS [3061] TO [3068]
(Default = 000) All report codes are preceded by a 3- or 4-digit Account
Number to ensure correct identification of system events. The Account
Number that is transmitted with the report code can correspond either to the
partition or to the central station telephone number (see section 8.6 on
page 27). Account Numbers can be any hexadecimal value from 0 to F.
Partition 2: [3202] Partition 4: [3402] Partition 6: [3602] Partition 8: [3802]
Table 4: Account Numbers
Disarming Report Schedule
Partition 1: [3103] Partition 3: [3303] Partition 5: [3503] Partition 7: [3703]
Day
Option
Section [3035],
Section [3035],
option [6] = disabled option [6] = enabled
[3061] Account Number 1 Partition 1
CSTN 1
[3062] Account Number 2 Partition 2
CSTN 2
Day
[3063] Account Number 3 Partition 3
CSTN 3
Partition 2: [3203] Partition 4: [3403] Partition 6: [3603] Partition 8: [3803]
Option
Section Account Number
[1]
Sunday (S)
[5]
Thursday (T)
[3064] Account Number 4 Partition 4
CSTN 4
[2]
Monday (M)
[6]
Friday (F)
[3065] Account Number 5 Partition 5
N/A
[3]
Tuesday (T)
[7]
Saturday (S)
[3066] Account Number 6 Partition 6
N/A
[4]
Wednesday (W)
[8]
Holidays (H)
[3067] Account Number 7 Partition 7
N/A
[3068] Account Number 8 Partition 8
N/A
8.3.3 Arming/Disarming Schedule Tolerance Window
(Default = 000) The Arming/Disarming Schedule Tolerance Window
lengthens the partition’s Arming/Disarming Schedule for some users. User
Access Codes with Add Tolerance Windows to Schedules enabled (refer to
26 REFERENCE & INSTALLATION MANUAL
For example, if the Account Number Transmission (see section 8.6 on page
27) corresponds to the partition, and a zone generates an alarm in Partition
1, the control panel will send the Partition 1 Account Number defined in
section [3061] followed by the report code.
Only the SIA format supports the [0] = 0 digit in its account
numbers. Account numbers that use other reporting formats
do not support the [0] = 0 digit. Enter the [STAY] = A digit in its
place. When using the SIA Format, and the Account Number
Transmission (see section 8.6 on page 27) corresponds to the
partition, the control panel only uses the Partition 1 Account
Number programmed in section [3061], but the report code
includes the partition number.
will come from either the Automatic Report Code List on page 52 or the
Contact ID Report Code List on page 54.
8.7.4 Ademco Contact ID
Ademco Contact ID is a fast communicator format that uses tone reporting
instead of pulse reporting. It also uses a pre-defined list of industry
standard messages and report codes that will suit most basic installation
needs. To manually program the report codes, use the 2-digit hexadecimal
values from the Contact ID Report Codes List in the Programming Guide.
Enter 00 to disable reporting or FF to use the default report code from the
Automatic Report Code List in the Programming Guide. To automatically
program a set of default Contact ID codes, refer to section 8.15.
8.6 ACCOUNT NUMBER TRANSMISSION
8.7.5 SIA FSK
SECTION [3035]: OPTION [6]
(Default = Partition Account #) Option [6] determines whether the account
number that is sent to the central station corresponds to a partition or to a
central station telephone number (CSTN).
SIA FSK is a fast communicator format that uses tone reporting instead of
pulse reporting. This communicator format uses a pre-defined list of
industry standard messages and report codes that will suit most basic
installation needs. To manually program the report codes, enter 00 to
disable reporting or any other value to use the default report code from the
Automatic Report Code List in the Programming Guide. To automatically
program a set of default SIA FSK codes, refer to section 8.15.
With option [6] enabled, the account number that is sent to the central
station corresponds to the CSTN that was dialed. Regardless of which
partition the report originated from, the account number for the
corresponding CSTN will be transmitted instead of the corresponding
partition account number. For example, a report originating from partition 8
is transmitted to CSTN 1. Although the report originated from partition 8,
Account Number 1 (see Table 4 on page 26) is transmitted with the report.
With option [6] disabled, the account number that is sent to the central
station corresponds to the partition where the event originated, regardless
of which CSTN is dialed. For example, a report originating from partition 8
is transmitted to CSTN 1. The account number that is transmitted to CSTN
1 is Account Number 8 (see Table 4 on page 26).
8.7 REPORTING FORMATS
SECTION [3070]
The control panel can use a number of different reporting formats, but each
of the four Monitoring Station Phone Numbers (see section 8.4) should be
programmed with the same reporting format unless they are combined with
a Pager format. The first digit entered into section [3070] represents the
reporting format (see Table 5) used to communicate with Monitoring Station
telephone number 1, the second digit represents telephone number 2, etc.
8.7.6 Pager Reporting Format
Using this format allows the control panel to transmit report codes to a
pager. A pound symbol “#” is automatically generated after the report code.
Also refer to Pager Delay in section 8.9.
8.8 EVENT CALL DIRECTION
As shown in Figure 8-1 on page 23, the control panel events are divided
into three event groups for each partition and two global event groups.
Each event group can be programmed to dial up to four Monitoring Station
telephone numbers with one used as a backup. The numbers are dialed
sequentially starting from 1, skipping any disabled numbers and stopping
once all selected telephone numbers have been reached. If the control
panel still fails to report to a Monitoring Station telephone number after
reaching the Maximum Dialing Attempts (see section 8.8.1), the control
panel will dial the selected backup telephone number unless the Alternate
Backup Option is enabled (see section 8.8.3). When the Alternate Backup
Option is enabled, the control panel will dial the backup number after every
failed attempt. For each section enable or disable the options:
Compatible Digital Alarm Communication Receivers (DACRs):*
Dialing sequence for:
Troubles and Restore Troubles: [3080]
- Sur-Gard DRL2A
- Ademco 685
Dialing sequence for:
Special System, Arming, Disarming, and Alarm Reporting: [3081]
- Osborne Hoffman Quick Alert II
Table 5: Reporting Formats*
0 = Ademco slow (1400Hz, 1900Hz, 10BPS)
4 = Contact ID Pager
Dialing sequence for: Access Code and Keyswitch Arming and Disarming
1 = Silent Knight fast (1400Hz, 1900Hz, 20BPS) 5 = Ademco Contact ID
Partition 1: [3127] Partition 3: [3327] Partition 5: [3527] Partition 7: [3727]
2 = Sescoa (2300Hz, 1800Hz, 20BPS)
6 = SIA FSK
Partition 2: [3227] Partition 4: [3427] Partition 6: [3627] Partition 8: [3827]
3 = Ademco Express (DTMF 4+2)
7 = Pager
* UL Note: Installer must verify the compatibility with of the DACR. Use
listed compatible DACRs.
8.7.1 Standard Pulse Formats
The control panel can use the Ademco slow, Silent Knight fast and Sescoa
standard pulse reporting formats (see Table 5).
8.7.2 Ademco Express
The Ademco Express is a high-speed reporting format that communicates
2-digit (00 to FF) report codes. Unlike other Ademco formats, the Ademco
Express does not use the Contact ID Report Codes.
8.7.3 Contact ID Pager
Using this format, the control panel will transmit a Contact ID report instead
of a user generated numerical code to a pager. The Contact ID report code
Dialing sequence for: Zone Alarms and Alarm Restores
Partition 1: [3128] Partition 3: [3328] Partition 5: [3528] Partition 7: [3728]
Partition 2: [3228] Partition 4: [3428] Partition 6: [3628] Partition 8: [3828]
Dialing sequence for: Tampers and Tamper Restores
Partition 1: [3129] Partition 3: [3329] Partition 5: [3529] Partition 7: [3729]
Partition 2: [3229] Partition 4: [3429] Partition 6: [3629] Partition 8: [3829]
(Default = only option [1] enabled)
Option Call:
Option Call (select one only):
[1]
Telephone Number 1
[5]
Backup on Number 1
[2]
Telephone Number 2
[6]
Backup on Number 2
DIGIPLEXNE CONTROL PANEL 27
[3]
[4]
Telephone Number 3
Telephone Number 4
[7]
[8]
Backup on Number 3
Option Feature
Backup on Number 4
[3]
8.8.1 Maximum Dialing Attempts**
SECTION [3056]
(Default = 008) The number (001 to 255, 000 = 8 attempts) programmed
into section [3056] determines how many times the control panel will dial
the same Monitoring Station Telephone Number before proceeding to the
next number. Also refer to section 8.8.3.
** UL Note: For UL Listed systems, the maximum dialing attempts must be
set to 5 to 10 attempts between the DGP-NE96’s two telephone lines.
8.8.2 Delay Between Dialing Attempts
SECTION [3054]
(Default = 020) This delay will determine the amount of time the control
panel will wait between dialing attempts. This delay can be set from 001 to
127 seconds.
8.8.3 Alternate Dialing Option
SECTION [3037]: OPTION [6]
(Default = disabled) With option [6] enabled in section [3037], the control
panel dials the selected backup telephone number after every failed
attempt to contact a Monitoring Station Telephone Number. Otherwise
(option [6] off), the control panel only dials the backup telephone number
after the Maximum Dialing Attempts (see section 8.8.1) to one Monitoring
Station Telephone Number fail.
8.9 PAGER DELAY
SECTION [3057]
(Default = 060) When using the Pager Reporting Format (see section
8.7.6), the control panel will wait for the delay period programmed into
section [3057] before uploading the report codes to the pager. This is to
allow time for the pager system to provide a dial tone or to bypass the
welcome message before sending the data. Enter any value between 001
and 127 to determine Pager Delay in seconds.
8.10 RECENT CLOSE DELAY
(Default = 000) If, after arming the partition, an alarm is generated within
the programmed period, the control panel will transmit the Recent Close
report code programmed into section [3933]. Enter any value between 001
and 255 to determine Recent Close Delay in seconds.
Partition 1: [3109] Partition 3: [3309] Partition 5: [3509] Partition 7: [3709]
Partition 2: [3209] Partition 4: [3409] Partition 6: [3609] Partition 8: [3809]
8.11 POWER FAILURE REPORT DELAY
SECTION [3058]
(Default = 030) The control panel will delay the transmission of the AC
Failure report code programmed into section [3941] by the period
programmed into section [3058]. Enter any value between 001 and 255 to
determine Power Failure Report Delay in minutes.
Description
[4]
After the number of days (000 to 255, default =
000) programmed into section [3040] elapse, the
control panel can transmit the report code at the
time (00:00 to 23:59, default = 00:00)
programmed into section [3041].
The control panel transmits the test report code at
Hourly Test the same time every hour. Program the minute of
ON OFF
Transmission each hour (00:00 to 00:59, default = 00:00) when
the test report should be sent into section [3041].
When armed: The control panel transmits the test
report code at regular intervals while the partition
is armed. Program the number of minutes (000 to
255, default 005) between each transmission in
Timed Test
Transmission section [3042].
ON ON
when Armed/ When disarmed: The control panel transmits the
test report code at regular intervals while the
Disarmed
partition is disarmed. Program the number of
minutes (000 to 255, default = 060) between each
transmission in section [3043].
Auto Test
Report
OFF OFF
Period
(default)
8.13 DISARM REPORTING OPTIONS
(Default = disabled) When option [7] is disabled, the control panel sends
the Disarming Report Codes (see section 8.2) every time the partition is
disarmed. When option [7] is enabled, the control panel sends the
Disarming Report Codes to the Monitoring Station only when the partition is
disarmed following an alarm. Select the section that corresponds to the
desired partition and enable or disable option [7]:
Partition 1: [3123] Partition 3: [3323] Partition 5: [3523] Partition 7: [3723]
Partition 2: [3223] Partition 4: [3423] Partition 6: [3623] Partition 8: [3823]
8.14 ZONE RESTORE REPORT OPTIONS
SECTION [3037]: OPTION [8]
(Default = disabled) When option [8] is disabled, the control panel sends
the Zone Alarm Restore report codes to the Monitoring Station when the
Bell Cut-Off Timer elapses (see section 7.2) or when the alarm is disarmed.
When option [8] is enabled, the control panel sends the Zone Alarm
Restore report codes (see section 8.2) to the Monitoring Station as soon as
the zone returns to normal (zone closure) or upon disarming.
8.15 AUTO REPORT CODE PROGRAMMING
When using either the Contact ID or SIA Reporting Formats (see section
8.7), the control panel can automatically program a set of default report
codes. However, the Contact ID Reporting Format can be modified using
the manual programming method (see section 8.7.4 & section 8.7.5) to
program remaining report codes or to change some of the defaults. From
programming mode (see section 3.4) enter any of the following sections to
set the indicated report codes with the default values (FF) from the
Automatic Report Codes List in the Programming Guide:
Section Description
8.12 AUTO TEST REPORT
SECTION [3037]: OPTION [3] AND [4] AND
SECTIONS [3040], [3041], [3042] AND [3043]
The control panel can transmit the test report code programmed into
section [3902] every hour (Hourly Test Transmission) or after a period of
time (Auto Test Report Period).
28 REFERENCE & INSTALLATION MANUAL
[4030]
Resets all the report code sections to 00 (cleared).
[4031]
Sets all the report code sections to FF (defaults).
Section Sets to Defaults (FF)
Reset Sections
[4032]
Zone Alarm and Restore Report Codes
Tamper and Restore Report Codes
[0201] to [0296]
[4033]
Keyswitch Arming Report Codes
Keyswitch Disarming Report Codes
Access Code Arming Report Codes
Access Code Disarming Report Codes
[0701] to [0732]
[0801] to [0832]
[2001] to [2099]
[2101] to [2199]
[4034]
Special System Report Codes
[3900] to [3909]
[4035]
Special Arming Report Codes
Special Disarming Report Codes
[3910] to [3919]
[3920] to [3929]
[4036]
Special Alarm Report Codes
[3930] to [3939]
[4037]
Trouble and Restore Report Codes
[3940] to [3991]
8.16 CLOSING DELINQUENCY TIMER
(Default = 000; Disabled) When a partition in the system is disarmed, the
control panel will start the corresponding partition’s Closing Delinquency
Timer, which is programmed for each partition. If the Closing Delinquency
Timer elapses before the partition is armed again, DigiplexNE will transmit
a “Closing Delinquency” report code to the central monitoring station. Enter
a value from 001 to 255 days into the appropriate section. Enter 000 to
disable the Closing Delinquency Timer.
For example, the Closing Delinquency Timer for partition 1 (section [3119])
is programmed for 005 days. When the system is disarmed, DigiplexNE will
begin the Closing Delinquency Timer for partition 1. If the partition has not
been armed within five days, DigiplexNE will transmit a “Closing
Delinquency” report code to the central monitoring station.
Partition 1: [3119] Partition 3: [3319] Partition 5: [3519] Partition 7: [3719]
Partition 2: [3219] Partition 4: [3419] Partition 6: [3619] Partition 8: [3819]
DIGIPLEXNE CONTROL PANEL 29
9
DIALER OPTIONS
9.1 TELEPHONE LINE MONITORING
9.5 SWITCH TO PULSE
SECTION [3036]: OPTIONS [1] AND [2]
When enabled, the system verifies the existence of the main telephone line
once every second. After each successful test, the Status LED on the
control panel flashes briefly. A line test failure occurs when the TLM detects
less than 3 volts for the period defined by the TLM Fail Timer (see section
9.1.1). If the line test fails, the control panel will generate one or more
conditions as defined by the TLM settings below, until it detects the
telephone line again. When the dialer detects a telephone ring, the TLM
test stops for 1 minute.
SECTION [3036]: OPTION [7]
(Default = disabled) When option [7] is enabled, the control panel switches
from tone dialing to pulse dialing on the fifth attempt to report events to the
Monitoring Station. The control panel continues to use pulse dialing until it
establishes communication. When the control panel switches to another
Monitoring Station telephone number, it returns to tone dialing and switches
back to pulse dialing on the fifth attempt.
Option Feature
[1]
When the line test fails
[2]
OFF OFF Disabled
TLM disabled (default) .
The Communicator trouble appears in the
Trouble Display.
The Communicator trouble appears in the
Alarm when
Trouble Display. If the partition is armed, the
OFF ON
Armed
control panel generates an alarm.
The Communicator trouble appears in the
Trouble Display. The control panel switches
Silent Alarms
ON ON
become Audible any triggered Silent Alarm zones or Silent
panic alarms to an audible alarm.
9.6 BELL ON COMMUNICATION FAIL
SECTION [3036]: OPTION [8]
(Default = disabled) When option [8] is enabled and the control panel fails
to communicate with the Monitoring Station when the partition is armed, the
control panel can enable the BELL output.
ON OFF Trouble Only
9.1.1 TLM Fail Timer
SECTION [3053]
(Default = 016) If the TLM does not detect the existence of the main
telephone line for the time programmed in this section, the control panel will
generate the condition(s) defined by the TLM options (see section 9.1).
Enter any value between 016 and 255 (value is X2 seconds) into section
[3053]. Entering a value between 000 and 016 will set the TLM Fail Timer
to 32 seconds.
9.2 TONE/PULSE DIALING
SECTION [3036]: OPTION [4]
(Default = enabled) When option [4] is enabled, the control panel can dial
using the tone/DTMF format. When option [4] is disabled, the control panel
uses the pulse dialing format. Refer to section 9.3 for setting the pulse ratio.
Option
Feature
[4]
ON
Tone/DTMF format
[4]
OFF
Pulse dialing format
9.3 PULSE RATIO
SECTION [3036]: OPTION [5]
(Default = enabled) When using Pulse dialing (see section 9.2), select one
of two Pulse Ratios. Although most European countries use the 1:2 pulse
ratio, the 1:1.5 ratio may provide better results in some cases. If the 1:1.5
pulse ratio is not providing the desired results in North American countries,
the 1:2 ratio may be used.
Option
Feature
[5]
ON
North American pulse ratio of 1:1.5
[5]
OFF
European pulse ratio of 1:2
9.4 BUSY TONE DETECTION
SECTION [3036]: OPTION [6]
(Default = enabled) When option [6] is enabled, the control panel
immediately hangs up if it receives a busy signal when it dials an outside
number.
30 REFERENCE & INSTALLATION MANUAL
9.7 KEYPAD BEEP ON SUCCESSFUL ARM OR DISARM REPORT
SECTION [3037]: OPTION [5]
(Default = disabled) When option [5] is enabled and a user arms or disarms
a partition, the keypad emits a beep tone to confirm that the Monitoring
Station received the arming or disarming report code.
9.8 DIAL TONE DELAY
SECTION [3037]: OPTION [7]
(Default = disabled) When option [7] is enabled, the dialer hangs up if no
dial tone is present after 32 seconds. When option [7] is disabled, the dialer
dials even if no dial tone is present after 3 seconds. If more time is required,
insert a 4-second pause into the desired telephone number sequence (see
section 8.4).
Option
Feature
[7]
ON
If no dial tone is present, dialer hangs up.
[7]
OFF
If no dial tone is present, force dials.
10
PROGRAMMABLE OUTPUTS
A PGM is a programmable output that toggles to its opposite state (i.e. a
normally open PGM will close) when a specific event occurs in the system.
For example, a PGM can be used to reset smoke detectors, activate strobe
lights, open/close garage doors and much more.
When a PGM closes, the control panel supplies a ground to the PGM
activating any device or relay connected to it. When a PGM opens, the
circuit opens from ground, therefore not providing any power to the devices
connected to it. The control panel provides a maximum of 100mA to PGM1
and 5A to PGM2 and PGM3. PGM1 is a normally open transistor output
and PGM2 and PGM3 are normally open or normally closed 5A relays. For
details on how to connect a relay to a PGM, please refer to section 2.8 on
page 4.
10.1 PGM ACTIVATION EVENT
The PGM Activation Event determines which event will activate the PGM.
The Event Group specifies the event, the Feature Group identifies the
source, and the Start # and End # sets the range within the Feature Group
(see PGM Programming Table in the Programming Guide).
For example, the control panel can activate PGM1 when the partition is
armed by User Access Codes 256 to 260. Therefore:
Event Group section [0910] = 010 “Arming with User Code”
Feature Group section [0911] = 001 “User Codes 256 to 511”
Start # section [0912] = 000
End # section [0913] = 004
Enter the sections that correspond to the Event Group, Feature Group,
Start # and End # of the desired PGM and enter the desired 3-digit number
from the PGM Programming Table:
Event Group Feature Group
Start #
End #
PGM 1:
[0910]
[0911]
[0912]
[0913]
PGM 2:
[0920]
[0921]
[0922]
[0923]
PGM 3:
[0930]
[0931]
[0932]
[0933]
10.4 PGM DEACTIVATION EVENT
The PGM Deactivation Event determines which event will return the PGM
to its original state. The Event Group specifies the event, the Feature Group
identifies the source, and the Start # and End # determine the range within
the Feature Group. The complete PGM Programming Table appears in the
Programming Guide.
For example, to deactivate PGM1 when zone 3 opens, program:
Event Group section [0914] = 001 “Zone is Open”
Feature Group section [0915] = 000 “Zone Numbers”
Start # section [0916] = 003
End # section [0917] = 003
Enter the sections that correspond to the Event Group, Feature Group,
Start # and End # of the desired PGM and enter the desired 3-digit number
from the PGM Programming Table.
Event Group Feature Group
Start #
End #
PGM 1:
[0914]
[0915]
[0916]
[0917]
PGM 2:
[0924]
[0925]
[0926]
[0927]
PGM 3:
[0934]
[0935]
[0936]
[0937]
10.5 PGM TIMER
When the PGM Deactivation Option (see section 10.2) is enabled, the PGM
Timer determines how many seconds or minutes (see section 10.5.1) the
PGM remains activated before it returns to its original state.
Enter the section that corresponds to the desired PGM and enter a value
from 001 to 255 (default = 005). The value entered is either in seconds or
minutes as determined by the PGM Time Base Selection (see section
10.5.1).
PGM 1: [0918]
PGM 2: [0928]
PGM 3: [0938]
10.5.1 PGM Time Base Selection
10.2 PGM DEACTIVATION OPTION
Once the PGMs are activated (see section 10.1), they can deactivate when
another event occurs or after a period of time. The PGM Deactivation
Option determines which method is used, the PGM Deactivation Event (see
section 10.4) or the PGM Timer (see section 10.5). Enter the section that
corresponds to the desired PGM and enable or disable option [1] (default =
PGM Deactivation Event):
PGM 1: [0919]
Option
Feature
PGM 2: [0929]
[1]
ON
PGM Timer
PGM 3: [0939]
[1]
OFF
PGM Deactivation Event
10.3 FLEXIBLE PGM DEACTIVATION OPTION
The PGM Deactivation Option (see section 10.2) must be set to PGM Timer
for this feature to function. The Flexible PGM Deactivation Option uses the
benefits of both the PGM Deactivation Event (see section 10.4) and the
PGM Timer (see section 10.5). When option [3] is enabled and the PGM is
activated (see section 10.1), it will deactivate when either the PGM
Deactivation Event occurs or the PGM Timer elapses, whichever happens
first.
For example, the PGM activates and the PGM Timer is set for 5 minutes.
However, the PGM Deactivation Event occurs before 5 minutes ends so the
PGM deactivates.
Enter the section corresponding to the PGM and enable option [3] (default
= disabled):
PGM 1: [0919]
PGM 2: [0929]
The PGM Time Base Selection determines whether the PGM Timers in
sections [0918], [0928] and [0938] are in minutes or seconds (default =
seconds). Enter the section corresponding to the desired PGM and enable
or disable option [2]:
PGM 1: [0919]
Option
Feature
PGM 2: [0929]
[2]
ON
Minutes
PGM 3: [0939]
[2]
OFF
Seconds
10.6 PGM1 BECOMES A 2-WIRE SMOKE DETECTOR INPUT*
SECTION [3030]: OPTION [1]
(Default = disabled) Enabling option [1] in section [3030] sets PGM1 to act
as a zone input for two-wire smoke detectors. When programming Zone
Numbering (see section 4.1), the control panel will recognize PGM1 as
input number 255. For two-wire smoke detector connections, please refer
to section 2.17.1 on page 9.
* UL Note: Not verified by UL.
10.7 PGM TEST MODE
Entering sections [0901] to [0903] activates the corresponding PGM for 8
seconds to verify if the PGM is functioning as desired.
PGM 1: [0901]
PGM 2: [0902]
PGM 3: [0903]
PGM 3: [0939]
DIGIPLEXNE CONTROL PANEL 31
11
SYSTEM SETTINGS AND COMMANDS
11.1 HARDWARE RESET
11.5 BATTERY CHARGE CURRENT
A Hardware Reset sets sections [0001] to [3991] to default, including the
Installer and System Master Codes. Only the Panel ID, PC Password, PC
Telephone Number and Event Buffer are not reset. A Hardware Reset
cannot be performed on a control panel with the Installer Code Lock
enabled (see section 11.3).
1) Make sure the Installer Code Lock is disabled
2) Remove the battery and AC power from the control panel.
3) Place the RESET jumper on the reset pins of the control panel.
4) Re-connect the AC power and the battery to the control panel.
5) Wait 10 seconds and remove the jumper.
SECTION [3030]: OPTION [5]
When option [5] is enabled, the battery’s charge current is 700mA (min.
40VA transformer). When option [5] is disabled, the charge current is
350mA. Depending on the battery’s capacity, enable or disable the option:
Option
Feature
[5]
ON
700mA
[5]
OFF
350mA (default)
11.6 COMBUS SPEED
11.2 SOFTWARE RESET
Performing a software reset will set certain parameters to default values or
program certain sections with a set of pre-defined values. To do so:
1) Place the RESET jumper on the reset pins of the control panel.
2) Enter Panel Programming Mode (see section 3.4).
3) Enter the 4-digit [SECTION] of the software reset you wish to perform:
Section Description
[4040]
Resets the programmable sections from [0001] to [3991] to
default (even if Installer Code Lock is enabled). The Event Buffer,
Panel ID, PC Password, PC Telephone Number and Zone, Door,
Partition and User Labels (see section 12.4) will not reset.
[4041]
Resets the System Master Code to 123456.
[4042]
Resets all Zone Programming sections from [0001] to [0196],
[0201] to [0296] and [0961] to [0984] to default.
[4043]
Resets the Access Control sections, except Door Labels (see
section 11.24), from [2201] to [2712] to default.
[4044]
Resets all User Access Code Programming sections from [1001]
to [1999] and [2001] to [2199] to default. User Labels (see
section 12.4) will not be reset.
[4045]
Resets all control panel settings from [3020] to [3043] and from
[3900] to [3991] and all the Dialer sections from [3051] to [3081]
to default.
[4046]
Resets all Partition Settings, except Partition Labels (see section
11.24), from [3101] to [3829] to default.
[4047]
Resets Keyswitch Programming sections from [0501] to [0832] and
all Programmable Outputs sections from [0901] to [0939] to default.
[4048]
Entering this section resets the User Labels from the User
Access Codes, the Zone Labels from [0301] to [0396], Door
Labels from [2301] to [2332], Partition Labels [3100], [3200],
[3300], [3400], [3500], [3600], [3700] and [3800] to default.
Do not remove power from the control panel.
SECTION [3030]: OPTION [8]
This feature sets the communication speed between the control panel and
the modules to either Normal or High speed. In large installations with many
modules where a quicker communication response time is needed, set the
speed to High. If you are experiencing communication troubles, set the speed
to Normal or install a Hub (APR3-HUB2) on the combus. The modules will
detect the speed set in the control panel and adjust their internal parameters
accordingly. When a change is made to the combus speed, the control panel
will restart within one minute to allow the modules to adjust to the change.
Option
Feature
[8]
ON
High Speed
[8]
OFF
Normal Speed (default)
Please note that when the combus speed is changed the following
will occur and is considered normal operation:
• The message COMM. TROUBLE CALL SERVICE will be
displayed on keypads connected to the combus.
• The AC and STATUS LEDs will begin to alternately flash and all
operations on the system will be suspended for approximately
one minute while the system reconfigures itself.
11.7 TRANSMIT ZONE STATUS ON SERIAL PORT
SECTION [3035]: OPTION [7]
By enabling option [7], the control panel will transmit zone status
information (zone open, zone close, zone tamper and fire loop) through the
serial port. Use this feature when there are devices or software connected
to the serial port of the control panel that require zone status information
such as WinLoad and the APR3-PRT1 Printer Module.
11.8 SERIAL PORT BAUD RATE
SECTION [3035]: OPTION [8]
When option [8] is enabled, the serial port’s baud rate is 38,400 baud.
When option [8] is disabled, the baud rate is 19,200 baud. Depending on
the baud rate set in WinLoad or NEware, enable or disable option [8]:
Option
Feature
11.3 INSTALLER CODE LOCK
[8]
ON
38,400 baud
SECTION [3001]
(Default = 000) Enter 147 into section [3001] to lock all programming.
When 147 is programmed, performing a hardware reset as described in
section 11.1 will not affect the current panel settings. To remove the Installer
Lock, enter 000 into section [3001].
[8]
OFF
19,200 baud (default)
If communication between the control panel and the computer is
experiencing difficulty at 38,400 baud, especially over long
distances, disable option [8] and reduce the baud rate of the
software to 19,200 baud.
11.4 DAYLIGHT SAVINGS TIME
SECTION [3030]: OPTION [3]
(Default = enabled) When option [3] is enabled, the control panel adjusts
the system's clock (time) for daylight saving changes. At 2:00AM on the first
Sunday of a full weekend in April, the control panel will add one hour to the
programmed time (clock). At 2:00AM on the last Sunday of a full weekend
in October, the control panel will subtract one hour from the time (clock).
32 REFERENCE & INSTALLATION MANUAL
11.9 PARTITIONING
SECTION [3031]: OPTIONS [1] TO [8]
(Default = only partition 1 enabled) The control panel can provide up to
eight completely independent partitions. Most features and options can be
independently set for each partition such as Event Reporting, Entry/Exit
Delay, Bell Squawk, One-touch Arming, Panic Alarms and many more. All
zones, keyswitch zones, user codes and system modules are assigned to
specific partitions, making this a true partitioned system. Enable the
option(s) that correspond to the desired partition(s):
Option Description
[1]
11.12 MODULE RESET
SECTION [4001]
To reset a module connected to the combus to its default values, key in the
module's serial number into section [4001].
Option Description
Partition 1
[5]
Partition 5
11.13 LOCATE MODULE
SECTION [4002]
To locate a specific module on the combus, key in the module's serial
number into section [4002]. The green LOCATE LED on the module flashes
until the serial number is re-entered into the section or the module’s tamper
or unlocate switch is pressed.
[2]
Partition 2
[6]
Partition 6
[3]
Partition 3
[7]
Partition 7
[4]
Partition 4
[8]
Partition 8
11.9.1 Panel Partition Assignment
SECTION [3020]
(Default = 00) The control panel will report system events as originating
from one or all enabled partitions. The System Troubles (i.e. AC Failure,
TLM Failure, etc.) can only be viewed through the partitions enabled in this
section. Enter a 2-digit decimal number from 01 to 08 which represent
partitions 1 to 8. Enter 00 to disable this feature.
11.10 SHABBAT FEATURE
SECTION [3030]: OPTION [4]
(Default = disabled) When option [4] is enabled, detectors and keypads in the
system no longer display system status through the LCD and/or LEDs between
noon (12:00PM) Friday and midnight (12:00AM) Saturday. Normal operation is
re-instated Sunday morning at 12:00:01AM. If required, a user can access all
the usual commands and features during the Shabbat period by pressing a key
or by entering their access code (also depending if and how Confidential Mode
is enabled in the keypad). When no actions have occurred for two minutes, the
Shabbat Feature will re-activate. During the Shabbat period:
• the LCD keypads only display the date and time
• the backlight is disabled
• the LED indicators on modules are disabled
11.11 INSTALLER FUNCTION KEYS
Press and hold the [0] key and key in the [INSTALLER CODE] to access the
installer functions and then...
For LCD keypads: Press the key indicated in the list below that
corresponds to the function you wish to activate.
For Grafica keypads: Press the center action key (Options), highlight the
desired function and then press the left action key (Select).
Keys
Description
[STAY]
TEST REPORT: Sends the Test Report report code programmed
in section [3902] to the Monitoring Station.
CALL WINLOAD: Dials the PC telephone number programmed
[FORCE] in section [3010] to communicate with a computer using
WinLoad.
[ARM]
ANSWER WINLOAD: Forces the control panel to answer a call
made by the Central Monitoring Station that is using WinLoad.
[DISARM]
CANCEL COMMUNICATION: Cancels all communication with
the Monitoring Station or WinLoad until the next reportable event.
[MEM]
INSTALLER TEST MODE: Perform walk tests where the bell or
siren squawks once when a zone opens and twice when it
closes. Press [MEM] again to exit. Partitions cannot be armed if
the Installer Test Mode is enabled.
[TRBL]
START MODULE SCAN: Verifies the status of modules on the
combus. The LCD Keypads display the serial number of each
module connected to the combus.
[ACC]
START VOLTMETER READING (DGP2-641 only): Verifies if the
combus is supplying sufficient power at the keypad’s location
(refer to the LCD Keypad Reference & Installation Manual).
11.14 MODULE PROGRAMMING
SECTION [4003]
All modules connected to the combus are programmed through the control
panel. To program a module, enter section [4003] to enter Module
Programming Mode (see section 3.5), key in the module's serial number
and follow the programming indicated in the DigiplexNE Modules
Programming Guide. To exit this mode, press the [CLEAR] key until Normal
Mode is displayed.
11.15 MODULE AND LABEL BROADCAST
SECTION [4004]
Module Broadcast
To copy the contents of the programming sections from one module to one
or more of the same type, key in the serial number of the source module in
section [4004], enter the serial numbers of all the destination modules and
press [ACC] if using an LCD keypad or the center action key (Start) if using
a Grafica keypad.
Label Broadcast
Copy the User Labels, Zone Labels (sections [0301] to [0396]), the Door
Labels (sections [2301] to [2332]) and the Partition Labels (sections
[3100], [3200], [3300], [3400], [3500], [3600], [3700] and [3800]) to all the
modules in the system that support these labels. To transmit the labels, in
section [4004], enter the control panel’s serial number. From the
Destination screen, do not enter a serial number and press [ACC] if using an
LCD keypad or the center action key (Start) if using a Grafica keypad.
The Module and Label Broadcast feature will only work when a
module is broadcasting its data to a module or to modules of
the same type and model number. For example, an APR-PRT1
(Printer Module) cannot broadcast to an APR3-PRT1. Likewise,
a DGP module cannot broadcast to a DGP2 module.
Module Broadcast Example:
Using an LCD keypad, to program two zone expansion modules
(SN#34540075 and SN#34412100) with the same settings and options of
zone expansion module SN#34540033:
1) Press and hold the [0] key.
2) Enter your [INSTALLER CODE] and then enter section [4004].
3) Enter 34540033, 34540075, and 34412100 and then press [ACC].
The control panel automatically copies the contents of 34540033 into the
other two zone expansion modules.
Label Broadcast Example:
Using a Grafica keypad, to copy the labels of the control panel
(SN#020000A2) to all modules that support the labels:
1) Press and hold the [0] key.
2) Enter your [INSTALLER CODE] and then enter section [4004].
3) Enter 020000A2.
4) From the Destination screen, press the center action key (Start).
The control panel will automatically copy its labels to all supporting modules.
11.16 SYSTEM DATE & TIME
The System Date and Time is programmed through the User Menu, please
refer to Clock Loss in section 15.12.
DIGIPLEXNE CONTROL PANEL 33
11.17 CLOCK COMPENSATION VALUE
11.23 MULTIPLE ACTION FEATURE
SECTION [3050]
(Default = Disabled) When the DigiplexNE’s clock is inaccurate, a clock
compensation value can be entered into section [3050] to correct the time
drift. At the beginning of every hour, the control panel will either add or
subtract the clock compensation value to/from its clock. Every value from
001 to 125 will add 0.008 seconds and every value from 128 to 253 will
subtract 0.008 seconds from the clock. (000 = Disabled)
SECTION [3033]: OPTION [1]
(Default = disabled) When option [1] is enabled, users will remain in the
User Menu after entering their access code. This allows users to perform
more than one action without having to re-enter their access code. With
option [1] off, the control panel will exit the User Menu after every action.
Adding Values:
The existing label displayed on the LCD screen can be modified to suit the
installation’s needs. Each label contains a maximum of 16 characters.
For example, change section [0301] “ZONE 01” to “FRONT DOOR”.
When System Labels are modified, the label is changed throughout the
system. The labels can be changed to reflect the location of the device or
area to enable users and installers to rapidly understand the information
displayed on the LCD screen. To re-program the System Label, enter the
desired section and use Table 6, Table 8 and Table 7 (page 34) to modify
the label. To re-program the System Labels in Hebrew or Russian, enter the
desired section and use Table 9 and Table 11 (Hebrew) or Table 10 and
Table 11 (Russian) on page 35.
001 to 125 = [value] x [.008] (+0.008 to 1 second)
Subtracting Values:
128 to 253 = [value] - [127] x [-.008] (-0.008 to -1.008 second)
Example: Entering a value of 100 will add .800 ([100] x [.008]) seconds to
the clock at the beginning of every hour. Likewise, entering a value of 200
will subtract -0.584 ([200] - [127] x [-.008]) seconds from the clock at the
beginning of every hour.
11.24 SYSTEM LABELS
11.18 REMOVE MODULE
SECTION [4005]
After entering section [4005], the control panel scans all modules on the
combus. If modules are missing (i.e. module was removed) during this
scan, the control panel erases the module's serial number and removes the
module from the control panel's memory.
For instructions on how to enter letters and special characters for the
Grafica keypad, refer to Grafica’s Online Manual. A complete Grafica
Online Manual is available on our web site at www.paradox.ca.
Zone Labels: Sections [0301] to [0396] represent Zones 01 to 96.
Door Labels: Sections [2301] to [2332] represent Doors 01 to 32.
11.19 SERIAL NUMBER VIEWING
SECTION [4000]
Enter section [4000] to view the serial number of the control panel as well
as the serial numbers of all modules on the combus.
For LCD Keypads: After entering section [4000], the keypad will display
the 8-digit serial number of the control panel. Use the [S] and [T] keys to
scroll through the serial number of each module connected to the combus.
For Grafica Keypads: After entering section [4000], the keypad will display
the 8-digit serial number of the control panel. Press the center action key
(Next) to scroll through the serial number of each module connected to the
combus.
11.20 POWER SAVE MODE
SECTION [3033]: OPTIONS [4]
(Default = enabled) When option [4] is enabled and the control panel is
running on the backup battery (no AC), the control panel can set all
keypads into a “sleep mode” or Power Save Mode. In Power Save Mode
the keypad's backlight and LEDs are disabled until a key is pressed, an
alarm occurs or an Entry Delay is triggered.
Partition Labels:
Partition 1: [3100] Partition 3: [3300] Partition 5: [3500] Partition 7: [3700]
Partition 2: [3200] Partition 4: [3400] Partition 6: [3600] Partition 8: [3800]
Table 6: Keys
Press
Feature
[STAY]
Insert Space
Inserts a blank space in the cursor’s position
[FORCE]
Delete
Deletes the character or blank space found
at the cursor’s position
[ARM]
Delete Until the
End
Deletes all characters and spaces to the
right of the cursor and at the cursor's position
[DISARM]
Numeric or
Alphanumeric
Toggles from numeric keys to alphanumeric
keys and vice versa (see Table 7)
[BYP]
Lower or Upper
Case
Toggles the case setting from lower to upper
case and vice versa
Special
Characters
The cursor will turn into a flashing black
square. Enter the 3-digit number that
represents the desired symbol (see Table 8
on page 35, Table 11 on page 35 and
Table 12 on page 35).
[MEM]
11.21 AUTO TROUBLE SHUTDOWN
SECTION [3021]
(Default = 00) If, in a 24-hour period, a trouble occurs more than the number
of times programmed in section [3021], the control panel stops reporting the
trouble. Enter a value (01 to 15, 00 = disabled) into section [3021]. Each
trouble has its own counter. The counter is reset every day at midnight.
11.22 NO AC FAIL DISPLAY
SECTION [3030]: OPTION [6]
(Default = disabled) When option [6] is enabled, the control panel will not
display the AC Failure as a trouble. When an AC Failure occurs with this
option enabled:
• the AC LED will extinguish
• the AC Failure report code will be reported.
• the trouble will not appear in the Trouble Display
• the keypad will not beep to indicate the trouble
34 REFERENCE & INSTALLATION MANUAL
Description
Table 7: Numeric and Alphanumeric keys
Numeric
Alphanumeric
Key
Press key
one time
Press key
one time
Press key
two times
Press key
three times
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
0
1
2
3
4
5
6
7
8
9
--A
D
G
J
M
P
S
V
Y
--B
E
H
K
N
Q
T
W
Z
--C
F
I
L
O
R
U
X
Table 8: Special Characters Catalogue
Table 9: Hebrew Keypad Letter Assignment
Table 11: Hebrew Special Characters Catalogue
Table 12: Russian Special Characters Catalogue
Table 10: Russian Keypad Letter Assignment
DIGIPLEXNE CONTROL PANEL 35
12
ACCESS CODES
12.1 INSTALLER CODE
SECTION [1000]
(Default: 000000) The Installer Code is used to enter the control panel's
programming mode, which allows you to program all the features, options
and commands of the control panel and any modules on the combus. The
Installer Code is six digits in length where each digit can be any value from
0 to 9. To change the Installer Code:
1) Press and hold [0]
2) Enter [INSTALLER CODE]
3) Key in [1000]
4) Enter new 6-digit [INSTALLER CODE]
The Installer Code can program the User Code Options and the
Partition Assignment, but cannot program the personal
identification numbers.
12.2 ACCESS CODE LENGTH
SECTION [3033]: OPTIONS [2] AND [3]
Access codes can be 1 to 6 digits in length. When programming access
codes with less than 6 digits, press the [ENTER] key after entering the last
digit. The control panel automatically removes the last 2 digits of the User
Access Code if the length is changed from 6 digits to 4 digits. However, if
the User Access Code Length is changed from 4 digits to 6 digits, the
control panel adds 2 digits to the end by using the first 2 digits.
For example, if the User Access Code is 1234 and you switch to 6 digits,
the code will become 123412.
Figure 12-1: Programming User Access Codes
Press & hold
the [0] key
Key in the
[INSTALLER
CODE]
Enter
[SECTION]
User Options
Feature Select
Programming
Press the [S] key
User
Partition
Assignment
Feature Select
Programming
Press the [S] key
Option Description
[2]
[3]
OFF OFF 4-digit User Access Code (Default)
OFF ON 6-digit User Access Code
Access
Level &
Schedule
Assignment
Enter digits
ON ON Flexible User Access Code
Where sections [1002] to [1999] represent
User Access Codes 002 to 999.
User Options
[1]
off
on
on
[2]
off
off
on
Feature
Master Feature Disabled
User can program PIN
User can program User Options,
Partition Assignment, PIN, and all
Access Control options
[3] Duress
[4] Bypass
[5] Arm Only
[6] Stay & Instant
[7] Force
[8] off = Access keypad’s partitions
on=Access user’s partitions
* Note: all users can regular arm.
Partition Assignment
[1] User Code has Access to Partition 1
[2] User Code has Access to Partition 2
[3] User Code has Access to Partition 3
[4] User Code has Access to Partition 4
[5] User Code has Access to Partition 5
[6] User Code has Access to Partition 6
[7] User Code has Access to Partition 7
[8] User Code has Access to Partition 8
Access Level & Schedule Assignment
First Brackets: Access Level
Enter Level from 00 to 15 (00 = all doors)
Second Brackets: Schedule
Enter number from 00 to 15 (00 = all times)
Access Control Options
12.3 SYSTEM MASTER CODE
SECTION [1001]
(Default: 123456) The Installer Code can change the User Code Options,
Partition Assignment and Access Control Options, but cannot change the
personal identification number (PIN). Each digit in the System Master Code
can be any value from 0 to 9. To reset the System Master Code, refer to
section 11.2 on page 32. With the System Master Code, a user can use any
of the available arming methods with access to all partitions and can
program all User Access Codes, User Options, Partition Assignments and
Access Control Options.
12.4 PROGRAMMING ACCESS CODES
SECTIONS [1002] TO [1999]
(Default = all options are off) The control panel supports 998 User Access
Codes. In sections [1002] to [1999], the Installer Code can program the
User Code Options, Partition Assignment and Access Control Options, but
cannot program the personal identification numbers (PIN). To program the
PINs, refer the users to the System Manager’s Manual. The System Master
Code or a user with the Master feature enabled can program the User Code
Options, Partition Assignment, Access Control Options and User Labels
using a different method of programming.
If no partition assignment is selected, the User Access Code will
only be able to activate PGMs.
To program user labels, refer to the LCD Keypad System
Manager’s Manual or to the Grafica Graphic LCD Keypad Online
Help.
Access
Control User
Options
Feature Select
Programming
Press the [S] key
Enter
Access Card
Press [ENTER]
or [S] to save
and go to the
next section.
[1] Access Control
[2] Can Disarm with Access Card
[3] Card with Door Unlocked Period Extension
[4] [5] Feature
off off Cannot Arm with Card (arming disabled)
on off Can Regular Arm with Card
off on Can Stay Arm with Card
on on Can Force Arm with Card
[6] Add Tolerance Window to Schedules
[7] off = Code can arm, disarm & access anytime
on = Code follows Schedule
[8] off = Valid Card can be granted access and
disarm partition
on = Valid Card can be granted access, but
Code required to disarm partition
Access Card Assignment
Enter Access Card's serial number manually or
present Card to the reader.
12.5 USER OPTIONS
SECTIONS [1002] TO [1999]: USER OPTIONS SCREEN, OPTIONS [1] TO [8]
The User Options define how each User Access Code can arm or disarm
the partitions. All users can Regular Arm (see section 15.1) their assigned
partitions, but only those with the Arm Only option disabled can disarm an
assigned partition.
Enable or disable the options as required for each User Access Code as
shown in Figure 12-1.
36 REFERENCE & INSTALLATION MANUAL
Option Feature
[1]
Description
the second set of brackets, enter the two-digit Primary Schedule number
(00 to 15, 00 = unrestricted) to be assigned to that User Access Code.
[2]
User cannot create or modify other User
Access Codes.
User can create new User Access Codes with
ON OFF Master enabled default options only, can program PINs and
User Labels.
User can create or modify User Access Codes
with the same partition assignment and
program the User Options, Partition
Full Master
ON ON
Assignment (can assign only partitions the
enabled
Master Code has access to), Access Control
features, PINs and User Labels.
A Duress enabled User Access Code can arm
or disarm the partition and can immediately
[3]
Duress
transmit a silent alarm to the Monitoring Station.
User can program bypass entries as
[4]
Bypass
described in section 15.7.
User can arm assigned partitions, but cannot
[5]
Arm Only
Disarm.
Stay or Instant User can Stay Arm or Instant Arm (see section
[6]
Arm
15.2) assigned partitions.
User can Force Arm assigned partitions (see
[7]
Force Arm
section 15.4)
Option [8] ON = User can access all its
assigned partitions, regardless of the keypad’s
User Menu
partition assignment.
[8]
Access
Option [8] OFF = User can only access the
partitions assigned to both itself and the keypad.
OFF OFF Master disabled
12.7.3 Access Control Options
SECTIONS [1002] TO [1999]: ACCESS OPTION SCREEN, OPTIONS [1] TO [8]
The Access Control Options define how each Access Card can arm or
disarm the partitions. To arm the partition(s) assigned to the door, a valid
card is presented to the reader twice within approximately 5 seconds while
the door remains closed. For the card to be valid, it must be presented
during its assigned Schedule, within its assigned Access Level and be
assigned to the keypad’s assigned partitions depending on the Door
Access Mode (see section 13.10). Enable or disable the options as
required for each Access Card as shown in Figure 12-1
A user that is not assigned to any partition, but has the access
control user option [1] enabled (“Access Control”), can now gain
access to an access control door by entering a code # (PIN) and
then pressing the [acc] keypad button.
Option Feature
[1]
[2]
[3]
12.6 PARTITION ASSIGNMENT
SECTIONS [1002] TO [1999]: ASSIGN AREA SCREEN, OPTIONS [1] TO [8]
Each of the 998 User Access Codes can be assigned to one or more
partitions. Users can only arm, disarm and view the status of the partitions
assigned to their User Access Codes. Select one or more of the partitions
for each User Access Code as shown in Figure 12-1 on page 36.
If no partition assignment is selected, the User Access Code will
only be able to activate PGMs.
[4]
OFF OFF Arming Disabled
Cannot arm partitions
ON OFF Regular Arm
Card can Regular Arm.
OFF ON Stay Arm
Card can Stay Arm.
ON ON Force Arm
Card can Force Arm.
[6]
SECTIONS [1002] TO [1999]
In addition to the User Access Code options, the following options can be
programmed when Access Control is enabled: Access Level, Schedule,
Access Options and Access Card. For details on Access Control, see
section 13 on page 38.
[7]
The System Master Code and User Access Codes with the Full
Master feature enabled can also program the Access Level,
Schedule, Access User Options, and Access Card using another
method for programming.
12.7.1 Access Level Assignment
SECTIONS [1002] TO [1999]: LEVEL + SCHEDULE SCREEN
User Access Codes can only open the doors included in their assigned
Access Level (see section 13.5 on page 38). In the first set of brackets,
enter the two-digit Access Level number (00 to 15, 00 = unrestricted) to be
assigned to that User Access Code.
12.7.2 Schedule Assignment
SECTIONS [1002] TO [1999]: LEVEL + SCHEDULE SCREEN
Schedules determine the hours, days and holidays that User Access Codes
can open the doors in their assigned Access Level (see section 13.6). In
ON = User’s Access Control feature is
enabled and user has access when the control
panel’s Access Control feature is enabled.
OFF = User’s Access Control feature is
Access Control
disabled, but the User Access Code
remains unaffected. This can be used to
disable a lost or stolen card without
deleting the User Access Code.
Card can unlock Door and disarm assigned
Card can Disarm
partitions. User Option [5]: Arm Only must
be disabled for this feature to function.
Card uses the Door Unlocked Period
Card with Extended
Extension feature (see DGP2-ACM1P’s
Unlocked Period
Reference & Installation Manual).
[5]
12.7 ACCESS CONTROL
The System Master Code has access to all doors all the time.
Only the card’s serial number and the choice of arming
method can be changed. If the other options are changed, the
System Master Code will revert to its original programming.
Description
[8]
Card and Code use the Schedule
Tolerance Windows (see section 8.3.3 on
page 26 and section 13.9 on page 39).
ON = Code is only valid during assigned
Code follows
Schedule (see section 12.7.2).
Schedule
OFF = Code is valid at all times.
ON = A door contact must be installed on
the Door, the Door must be assigned to a
zone (section 4.1) and the zone defined as
an Entry Delay. A valid Card can unlock the
Door, but cannot disarm the partition. If the
partition is armed, the Entry Delay is
Card to Unlock and
triggered and a User Access Code must be
Code to Disarm
entered to disarm the area. User Option [5]:
Arm Only and Access Control Option [2]:
Card can Disarm must be disabled for this
feature to function.
OFF = A valid Card can unlock the Door
and disarm the partition.
Add Tolerance
Windows to
Schedules
12.7.4 Access Card Assignment
SECTIONS [1002] TO [1999]: ACCESS CARD SCREEN
The Access Card is activated by assigning its serial number to the User
Access Code. Digiplex NE supports 26-bit Wiegand proximity cards and
readers (recommended: Position Technology’s CR-R880-A reader and CRR700 Series cards). Enter the serial number manually or present the Access
Card to the keypad’s reader and its serial number will register automatically.
DIGIPLEXNE CONTROL PANEL 37
13
ACCESS CONTROL: SYSTEM FEATURES
Access Control defines the days and times people are allowed to enter and
exit a site. An Access Control door uses a reader, an Access Control
Module, a Request-for-Exit motion detector, a door contact and an
electronic door strike to unlock the door for authorized personnel at
authorized times. For details on connecting these devices, refer to the
Digiplex/DigiplexNE Access Control Module Reference & Installation
Manual.
Figure 13-1: Typical Access Control Installation*
13.2 PROGRAMMING OVERVIEW
Several features and options for Access Control are available in the
DigiplexNE system. Some are programmed through the control panel and
are explained in this manual. Other features and options are explained in
the Access Control Module Reference & Installation Manual. The following
is the MINIMUM required to program Access Control:
Step 1: Enable Access Control in section [3038] option [1]
Step 2: Assign the Doors in sections [2201] to [2232]
Step 3: Create the Access Levels in sections [2601] to [2615]
Step 4: Create the Schedules in sections [2401] to [2432]
Step 5: Set the Holidays in sections [2701] to [2712]
Step 6: Program User Access Codes (see section 12 on page 36)
Step 7: Program the Access Control Modules (see Modules Programming
Guide)
13.3 ENABLE ACCESS CONTROL
1 = Request for Exit Device (Paradoor)
2 = Door Contact
3 = Reader (PosiProx or PosiPIN) on other side
of the wall
4 = Access Control Module (DGP2-ACM1P)
5 = Locking Device
6 = Control Panel (DGP-NE96)
SECTION [3038]: OPTION [1]
(Default = disabled) When option [1] is enabled, the Access Control feature
is activated. The control panel and the doors must be programmed (see
section 13.2).
13.4 DOOR NUMBERING
Each person authorized to access the protected area is issued a card. The
card is assigned to a User Access Code programmed with an Access Level
(see section 13.5) and a Schedule (see section 13.6). When a card is
presented to the reader, the control panel determines whether or not to
unlock the door depending on if the card is allowed to open that door and if
the card is permitted at that particular time and day.
* UL Note: For UL Listed systems, the DGP2-641AC keypad shall be used for
Access Control systems. The keypad is only compatible with the PosiProx
(CR-R880-A) reader.
13.1 COMMON ACCESS CONTROL TERMS
Access Alarm: An audible or silent warning generated by the reader to
indicate that an Access Door is open past the programmed time allowed or
that it was opened without an “Access Granted” or “Request for Exit” signal.
This event is logged in the Event Buffer, but cannot be reported.
Access Card: A tag assigned to a User Access Code used to identify the
user to the Access Control system. By presenting the tag to a reader, the
system can verify whether the tag is valid.
Access Denied: An Access Control term for the system’s refusal to admit
access through an Access Door.
SECTIONS [2201] TO [2232]
Each door to be monitored and controlled requires an Access Control
Module (DGP2-ACM1P). The keypad or module is assigned to the door
through the its serial number in sections [2201] to [2232]. DigiplexNE
supports up to 32 Doors.
13.5 ACCESS LEVELS
SECTIONS [2601] TO [2615]
Access Levels determine which Doors a user can access. Each Access
Level is a combination of the Doors from sections [2201] to [2232] (see
section 13.4). Access Levels are assigned to the users through their User
Access Codes (refer to the System Manager’s Manual).
For example, if the options [1], [2] and [3] are enabled in the First Screen of
section [2601], any User assigned to Level 01 will only have access to
doors 01, 02, and 03.
Access Levels from 01 to 15 are programmed in sections [2601] to [2615]
respectively. Each section contains four screens of 8 options representing
the 32 Doors. Level 00 allows the user access to all the Doors. For each
Access Level enable or disable the options as required:
Section
1st Screen 2nd Screen 3rd Screen 4th Screen
Doors
Doors
Doors
Doors
Access Granted: An Access Control term for the system permitting
admission through a protected door.
Burglar Alarm: An audible or silent warning sent to the control panel
indicating that an armed zone in the DigiplexNE security system has been
breached. This event is logged in the Event Buffer and can be reported to a
Monitoring Station.
Door Left Open: Each Access Door is programmed with a period of time it
is allowed to remain open. Once the door has been open past this time
limit, an Access Alarm will be triggered.
Forced Door: An Access Door was opened without an “Access Granted” or
“Request for Exit” signal, a silent or audible Access Alarm can be triggered.
Reader: An Access Control device (Posiprox CR-R880-A) normally located
near an Access Door that serves to relay the information from an Access
Card presented to it to the control panel.
Request for Exit: When a REX device (Paradoor 460) installed above an
Access Door within a protected area detects movement, it sends a requestfor-exit signal to the panel.
Valid Card: An Access Card presented to a reader during its assigned
Schedule and within its assigned Access Level.
38 REFERENCE & INSTALLATION MANUAL
Options [1] to [8] represent:
Level 01: [2601]
01 to 08
09 to 16
17 to 24
25 to 32
01 to 08
09 to 16
17 to 24
25 to 32
to
Level 15: [2615]
13.6 ACCESS SCHEDULES
SECTIONS [2401] TO [2432]
The Access Levels described in section 13.5 determine the Doors a user
can have access to and the Schedules determine when the user can have
access to those Doors.
Each Schedule consists of two programmable time periods called Interval A
and Interval B. For each Interval determine when users will have access by
programming the Start Time in the first screen and the End Time in the
second screen according to the 24hr. clock (i.e. 9PM = 21:00). The
Intervals are only valid during the days programmed in the third screen.
Option [8] in the third screen represents the programmed holidays (see
section 13.8). When option [8] is enabled, users have access between the
Start Time and End Time during the holidays. An Interval cannot cross into
another day (overnight). Schedules are assigned to the users through their
User Access Codes (refer to the System Manager’s Manual).
For example, program Schedule 001 in section [2401]:
A = Start time 09:00, End time 17:00, options 2, 3, 4, 5, and 6 enabled
B = Start time 10:00, End time 17:00, options 1, 7, and 8 enabled
Then, any User Access Code with this Schedule assigned will have access
Monday to Friday from 9AM to 5PM and on Saturday, Sunday and Holidays
from 10AM to 5PM.
Primary Schedules 001 to 015 are programmed in sections [2401] to
[2415] respectively. Secondary Schedules 016 to 032 are programmed in
sections [2416] to [2432] respectively. For each Schedule enter the Start
Time, End Time and enable or disable the options as required for each
Interval. Schedule 000 allows the user access at all times. Only Primary
Schedules can be assigned to User Access Codes. Secondary Schedules
are used as Backup Schedules (see section 13.7).
Section
Start Time End Time Days
1st Screen 2nd Screen 3rd Screen
set as per
Schedule 001: [2401] A: 24hr. clock
to
Schedule 032: [2432] B: set as per
24hr. clock
set as per
24hr. clock
set as per
24hr. clock
[1] = Sunday (S)
[2] = Monday (M)
[3] = Tuesday (T)
[4] = Wednesday (W)
[5] = Thursday (T)
[6] = Friday (F)
[7] = Saturday (S)
[8] = Holidays (H)
13.7 BACKUP SCHEDULES
SECTION [2501] TO [2532]
When an Access Card or User Access Code is used at an Access Door, the
control panel verifies whether it was used during its assigned Primary
Schedule. If the Primary Schedule is linked to another Schedule, it will
verify the linked Schedule and any Schedule linked to it. The control panel
will verify up to 8 linked Schedules, one after another, until it determines
whether the card or code is valid. Each Schedule (Primary or Secondary)
from 001 to 032 can be linked to another Schedule in sections [2501] to
[2532] respectively. In each section enter the 3-digit Schedule number of
the Schedule to be linked with it.
For example, if Schedule 001 is linked to Schedule 005 and Schedule 005
is linked to Schedule 030, then the control panel will verify Schedules 001,
005 and 030.
13.8 HOLIDAY PROGRAMMING
SECTIONS [2701] TO [2712]
Holiday Programming identifies the days that are considered holidays in the
Schedules. When option [8] is enabled in sections [2401] to [2432], access
is permitted during the holidays. Each section from [2701] to [2712]
represents a month from January to December respectively. Each section
includes four groups of five to eight options that represent the days of the
month. Enable the options representing the holidays.
For example, if [1] and [2] are enabled in the first screen in section [2701],
then January 1 and 2 are designated as holidays.
extended by 1 hour before and 1 hour after their assigned Schedule (see
Figure 13-2).
Figure 13-2: Example of a Schedule Tolerance Window
User’s assigned Schedule is 9AM to 5PM. When Add Tolerance Windows to
Schedules is enabled for the user, the user has access from 8AM to 6PM.
Schedule Tolerance Windows
The Schedule Tolerance Window applies to Access Schedules
only (section 13.6). The Schedule Tolerance Window does not
apply to the Arming and Disarming Report Schedules (section
8.3.1 and section 8.3.2).
13.10 DOOR ACCESS MODE
SECTION [2251] TO [2282]: OPTION [1]
Each Access Door can be assigned to one or more partitions in the security
system and each user can be assigned to one or more partitions. This
means that the actions performed by the user will be directly linked to the
partition(s) assigned to that door. Doors 01 to 32 are programmed in
sections [2251] to [2282] respectively. For each door enable or disable the
option as required:
Option
Feature
[1]
ON
[1]
OFF
“OR” Access Door
The Access Door grants access or permits arming or
disarming to users assigned to at least one of the door’s
partitions. An “OR” door will arm or disarm only the
partitions that it has in common with the users.
“AND” Access Door
The Access Door grants access or permits arming only to
users assigned to all the door’s assigned partitions.
13.11 CODE ACCESS
SECTION [2251] TO [2282]: OPTION [2]
Code Access can allow access to an Access Door by entering a valid User
Access Code and pressing the [ACC] key on a DGP2-641 LCD Keypad
instead of using the Access Card. The control panel will verify the User
Access Code’s validity in the same way it would verify the Access Card (i.e.
through its assigned Access Level and Schedule). Doors 01 to 32 are
programmed in sections [2251] to [2282] respectively. For each door
enable or disable the option as required:
Option
Feature
[2]
ON
[ACC] key enabled
[2]
OFF
Access with Card only
This option is not available for LED and Grafica Keypads.
13.12 CARD AND CODE ACCESS
13.9 SCHEDULE TOLERANCE WINDOW
SECTION [3039]
The Schedule Tolerance Window lengthens the assigned Schedule of
some users. User Access Codes with Add Tolerance Windows to
Schedules enabled have the number of minutes programmed in [3039]
added before and after their Schedule. This feature can be used instead of
creating Schedules for each shift and each shift’s supervisor by assigning
the supervisors to their respective shift’s Schedule and enabling Add
Tolerance Windows to Schedules on their User Access Codes. Enter any
value between 001 and 255 (default = 000) to determine Schedule
Tolerance Window in minutes.
For example, if 060 is programmed in section [3039], users with Add
Tolerance Windows to Schedules enabled will have their Schedule
SECTION [2251] TO [2282]: OPTION [3]
For higher security areas, the Access Door can be programmed to require a
user to present a valid Access Card and then enter the same user’s valid
code before access is granted. The Access Card must be presented to, and
the user code must be entered on, a PosiPIN™ Proximity Card Reader and
Keypad (CR-R885-BL) that is connected to an Access Control Module
(DGP2-ACM1P). PosiPIN and the Access Control Module must be
configured to allow access of this type. Please refer to the PosiPIN
Installation and Operating Instructions, and to the Access Control Module
Reference & Installation Manual for programming instructions. Doors 01 to
32 are programmed in sections [2251] to [2282] respectively. For each
door enable or disable the option as required:
DIGIPLEXNE CONTROL PANEL 39
Option
Feature
13.18 LOGGING ACCESS CONTROL EVENTS
[3]
ON
Access Card AND User Access Code required
13.18.1 Log Request For Exit In Event Buffer
[3]
OFF
Access Card OR User Access Code
SECTION [3038]: OPTION [2]
(Default = disabled) When a Request-for-Exit (REX) device registers
movement at the door, a REX event is generated (see section 13.1). When
option [2] is enabled, the control panel can record the REX events
generated from all the Doors in the Event Buffer, but cannot report these
events to the Monitoring Station. The events can be viewed by entering the
Event Record Display (see section 15.10).
When option [3] is enabled, the Access Card must be presented
before the User Access Code is entered.
13.13 SKIP EXIT DELAY WHEN ARMING WITH ACCESS CARD
SECTION [3038]: OPTION [6]
(Default = disabled) When an Access Card is presented to a reader twice
within approximately 5 seconds with the door closed, some or all the
partitions (see section 13.10) assigned to the Access Door can arm with or
without starting the Exit Delay. This feature is useful when the reader is
outside the partition so the partition(s) can be armed immediately.
Option
When arming with an Access Card:
[6]
ON
The Exit Delay is cancelled
[6]
OFF
The Exit Delay is triggered
13.14 RESTRICT ARMING ON DOOR
SECTION [2251] TO [2282]: OPTION [4]
With option [4] ON, the control panel can prevent an Access Card from
arming the partition(s) assigned to the door even if the Access Card is
programmed to permit arming.
13.15 RESTRICT DISARMING ON DOOR
SECTION [2251] TO [2282]: OPTION [5]
With option [5] ON, the control panel can prevent an Access Card from
disarming the partition(s) assigned to the door even if the Access Card is
programmed to permit disarming.
13.16 DOOR ACCESS DURING CLOCK LOSS
SECTION [3038]: OPTION [8]
(Default = disabled) If the system registers a Clock Loss Trouble, the
control panel will no longer recognize the Schedules. Only the System
Master Code and User Access Codes with the Master feature enabled can
reset the clock when option [8] is enabled. To avoid Clock Loss, a RTC is
incorporated in the control panel. Enable or disable the option as required:
Option
Until the Clock is reset, access can be granted to:
[8]
ON
The System Master Code or User Access Codes with Full
Master or Schedule 00 enabled
[8]
OFF
All users regardless of their programmed Schedules
13.17 BURGLAR ALARM ON FORCED DOOR OR DOOR LEFT OPEN
SECTION [3038]: OPTION [5] (FORCED DOOR)
SECTION [3038]: OPTION [7] (DOOR LEFT OPEN)
(Default = disabled) When option [5] and/or [7] is enabled and an Access
Door is forced open or left open, it can send a signal to the control panel to
trigger the burglar alarm and to report to the Monitoring Station. The burglar
alarm is generated instantly regardless of the zone’s definition (i.e. entry
delay is ignored). Also, see “Log Door Forced Open Restore In Event
Buffer” on page 40 and see “Log Door Left Open Restore In Event Buffer”
on page 40.
For these features to function, the following must be done:
• Install a door contact and connect it to the door’s Access Control Module
• Assign the door’s Access Control Module to a zone (see “Zone
Programming” on page 12)
• Enable option [5] in section [3038]: Burglar Alarm on Forced Door
• Enable option [7] in section [3038]: Burglar Alarm on Door Left Open
40 REFERENCE & INSTALLATION MANUAL
Since REX events can occur often, the Event Buffer may fill up
quickly.
13.18.2 Log Door Left Open Restore In Event Buffer
SECTION [3038]: OPTION [3]
(Default = disabled) Door Left Open Restore means that an Access Door
closed after it was left open beyond a programmed Door Left Open Interval
(refer to the Digiplex/DigiplexNE Access Control Module Reference &
Installation Manual). When option [3] is enabled, the Door Left Open
Restore event can be recorded in the Event Buffer. These events cannot be
reported to the Monitoring Station, but can be viewed by entering the Event
Record Display (see section 15.10).
13.18.3 Log Door Forced Open Restore In Event Buffer
SECTION [3038]: OPTION [4]
(Default = disabled) Door Forced Open Restore means that an Access
Door’s door contact closes after it was opened without the use of a valid
Access Card or User Access Code or receiving a Request for Exit signal.
When option [4] is enabled, the Door Forced Open Restore event can be
recorded in the Event Buffer. This event cannot be reported to the
Monitoring Station, but it can be viewed by entering the Event Record
Display (see section 15.10).
14
WINLOAD SOFTWARE
14.1 PANEL IDENTIFIER
SECTION [3011]
(Default = 0000) The Panel Identifier identifies the control panel to WinLoad
before initiating upload or download. The control panel will verify if the
Panel Identifier in WinLoad is the same. If the codes do not match, the
control panel will not establish communication. Therefore, program the
same Panel Identifier into both the control panel and WinLoad. Enter the
desired 4-digit hexadecimal number into section [3011].
14.2 PC PASSWORD
SECTION [3012]
(Default = 0000) The PC Password identifies the computer running the
WinLoad software to the control panel before beginning the download
process. Program the same PC Password into both the control panel and
WinLoad. If the passwords do not match, WinLoad will not establish
communication. Enter the desired four-digit hexadecimal number into
section [3012].
14.3 PC TELEPHONE NUMBER
SECTION [3010]
The control panel dials this number to communicate with a computer using
WinLoad. Enter any digit from 0 to 9 and any special keys or functions (see
Table 3, Special Telephone Number Keys, on page 26) up to a maximum of
32 digits into section [3010].
14.4 CALL BACK FEATURE
SECTION [3037]: OPTION [1]
(Default = disabled) The Call Back Feature provides additional security.
When option [1] is enabled and a computer using WinLoad attempts to
communicate with the control panel, the control panel hangs up and calls
the computer back to re-verify identification codes and re-establish
communication. When the control panel hangs up, WinLoad automatically
goes into Wait For Call Mode (see WinLoad’s Online Help), ready to
answer when the control panel calls back. The PC Telephone Number must
be programmed (see section 14.3).
and then press the left action key (Select). To hang up, highlight Cancel
Communication and then press the left action key (Select).
14.7 ANSWERING MACHINE OVERRIDE DELAY
SECTION [3052]
(Default = 008) If WinLoad will be used to communicate with an installation
that uses an answering machine or service, program the Answering
Machine Override. If the installation is called back within the programmed
delay period, the Answering Machine Override will bypass the answering
machine or service by picking up the line on the first ring. Also, see section
14.8.
In section [3052] program a value (00 to 15 X 4 seconds, 00 = disabled)
representing the delay period the control panel will wait between the first
and second call.
To use:
Step 1: Using WinLoad, call the installation and on the second ring press
the [ENTER] key on the keyboard to hang up or hang up manually.
Step 2: After hanging up, WinLoad will immediately call the installation back
or call the site back manually.
For example, an answering machine is set to answer after three rings and
section [3052] is programmed with 10 (10 x 4 = 40 seconds). During the
first call with WinLoad, wait two rings and press [ENTER]. WinLoad will
immediately call the site back. If the second call is made within 40 seconds,
the control panel will pick up the line on the first ring. If it takes more than 40
seconds, the control panel will not answer on the first ring and the
answering machine will answer after three rings.
14.8 RING COUNTER
SECTION [3051]
(Default = 008) The Ring Counter represents the number of rings the
control panel will wait before picking up the line. If the line is not answered
after the number of programmed rings, the control panel answers the call. If
more than 10 seconds pass between each ring, the Ring Counter resets.
Also, see section 14.7. Enter any value between 01 to 15 (00 = disabled) to
determine the number of rings.
14.5 CALL WINLOAD
14.9 EVENT BUFFER TRANSMISSION
Dial the PC Telephone Number programmed in section [3010] to
communicate with WinLoad. The control panel and WinLoad verify that the
Panel Identifier and the PC Password match before establishing
communication.
SECTION [3037]: OPTION [2]
(Default = disabled) Once the Event Buffer contains 1998 events since the
last upload, the control panel makes two attempts to establish
communication with a computer using WinLoad by calling the PC
Telephone Number programmed in section [3010]. WinLoad must be in
Wait To Dial mode. When communication is established, the control panel
uploads the contents of the Event Buffer to WinLoad. If communication is
interrupted before completing transmission or communication is not
established after two attempts, the control panel wait until the Event Buffer
receives another 1998 events before attempting Event Buffer Transmission.
When the Event Buffer is full, each subsequent new event will erase the
oldest event in the buffer. The Event Buffer can hold 2048 Events.
WinLoad must be in Wait For Call Mode (see WinLoad’s Online
Help).
For LCD Keypads: Press and hold the [0] key, enter your [INSTALLER
and then press [FORCE].
CODE]
For Grafica Keypads: Press and hold the [0] key, enter your [INSTALLER
CODE], press the center action key (Options), highlight Call WinLoad and
then press the left action key (Select).
14.6 ANSWER WINLOAD
To perform on-site uploading/downloading, connect the computer directly to
the control panel using an ADP-1 line adapter. In WinLoad set Dialing
Condition to Blind Dial. Program the PC telephone number in WinLoad and
follow the ADP-1 Adapter‘s instructions. When the computer has dialed...
For LCD Keypads: Press and hold the [0] key, enter the [INSTALLER CODE]
and press [ARM] to manually answer WinLoad from the panel. Press
[DISARM] to hang up.
For Grafica Keypads: Press and hold the [0] key, enter the [INSTALLER
CODE], press the center action key (Options), highlight Answer WinLoad
DIGIPLEXNE CONTROL PANEL 41
15
USER FEATURES
15.1 REGULAR ARMING
This method is used for the everyday arming of the system. All zones within
the partition must be closed to arm the system. The system can also be
Regular Armed by using a One-touch Feature (see section 6.15) or a
Keyswitch (see section 5.4.3). All users are able to Regular Arm the
partition(s) assigned to their User Access Codes. Refer to How to Arm on
page 42 for information on how to Regular Arm the system.
2)
3)
4)
5)
Using the scroll keys, highlight the desired arming method (see
Table 13 on page 42) and then press the center action key (Ok). If the
users have access to more than one partition, proceed to step 3.
Highlight either Arm All Areas or Select Area(s) and then press the
center action key (Ok). If the user(s) selected the Select Area(s)
method, follow steps 4 and 5.
Highlight a partition you wish to arm and then press the left action key
(Select). Repeat this step for any additional partition.
Press the center action key (Arm).
15.2 STAY ARMING
Stay Arming partially arms the partition to permit the user to remain in the
partition. Stay Zones (see section 4.5.3) will not arm when Stay Arming.
Partitions can also be armed by the Stay Arm One-touch Feature (see
section 6.15) or a Keyswitch (see section 5.4.4). Only User Access Codes
with the Stay and Instant Arm option enabled can Stay Arm a partition.
For example, arm the doors and windows without arming the motion
detectors. Refer to How to Arm on page 42 for information on how to Stay
Arm the system.
15.2.1 Stay Arming with Delay
Stay Arming with Delay functions like Stay Arming except armed zones are
programmed with an Entry Delay Timer (see section 4.3.14). If a zone is
triggered, the delay starts allowing the user time to disarm the partition(s).
Table 13: Arming Methods
Arming Method
LCD
Regular
[ARM]
Stay
[STAY]
Instant
[5]
Force
[FORCE]
Grafica
(Arm System)
(Stay Arm)
(Instant Arm)
(Force Arm)
15.3 INSTANT ARMING
Similar to Stay Arming, Instant Arming partially arms the partition to permit
the user to remain in the partition, but all Delay zones become Instant
zones. Partitions can also be armed by the Instant One-touch Feature (see
section 6.15) or a Keyswitch (see section 5.4.6). Only User Access Codes
with the Stay and Instant Arm option enabled can Instant Arm a partition.
Refer to How to Arm on page 42 for information on how to Instant Arm the
system.
15.3.1 Instant Arming with Delay
Instant Arming with Delay functions like Instant Arming except armed zones
are programmed with an Entry Delay Timer (see section 4.3.14). If a zone
is triggered, the delay starts allowing the user time to disarm the partitions.
15.4 FORCE ARMING
Force Arming allows the user to arm a partition when Force zones are open
(see section 4.5.4). Once the open zone in an armed partition is closed, the
system will then arm it as well. This feature is commonly used when a
motion detector is protecting an area that is occupied by a keypad. The
system can also be Force Armed by using a One-touch Feature (see
section 6.15) or a Keyswitch (see section 5.4.5). Only User Access Codes
with the Force Arm option enabled can Force Arm a partition.
For example, during Force arming the motion detector remains unarmed
until the user exits the area. The system will then arm the motion detector.
Refer to How to Arm on page 42 for information on how to Force Arm the
system.
15.5 HOW TO ARM
The following section details how to arm the system using an LCD or
Grafica keypad.
For LCD Keypads: To arm, users:
1) Enter their [ACCESS CODE].
2) Press the key corresponding to the desired arming method (see
Table 13 on page 42). If the users have access to more than one
partition, they can press the key(s) corresponding to the desired
partition(s) or press [0] to arm all their assigned partitions.
For Grafica Keypads: To arm, users...
1) Enter their [ACCESS CODE].
42 REFERENCE & INSTALLATION MANUAL
15.6 DISARMING
All users can disarm, except users with Arm Only (see section 12.5)
enabled on their User Access Codes. Users can only disarm the partitions
assigned to their User Access Codes. The Stay or Instant Armed partitions
can also be Disarmed by using a One-touch Feature. To disarm, users...
For LCD Keypads:
1) Enter through a designated entry. The Entry Delay Timer will begin.
2) Enter their [ACCESS CODE].
3) Press the [DISARM] key. If the users have access to more than one
partition, they can press the key corresponding to the desired partition
or press [0] to disarm all their assigned partitions.
For Grafica Keypads:
1) Enter through a designated entry. The Entry Delay Timer will begin.
2) Enter their [ACCESS CODE].
3) Using the scroll keys, highlight Disarm and then press the center
action key (Ok). If you have access to more than one area, proceed to
step 4.
4) Highlight either Disarm All Areas or Select Area(s) and then press
the center action key (Ok). If you selected the Select Area(s) method,
follow steps 5 and 6.
5) Highlight the area you wish to disarm and then press the left action
key (Select). Repeat this step for any additional area.
6) Press the center action key (Disarm).
15.7 BYPASS PROGRAMMING
Bypass Programming allows users to program the security system to ignore
specified zones the next time the partition is armed. To bypass a zone, the
zone must have the Bypass option enabled, the User Access Code must
have the Bypass option enabled, and the zone must be within the User
Access Code’s partition assignment. To Bypass, users...
For LCD Keypads:
1) Enter their [ACCESS CODE].
2) Press the [BYP] key.
3) Enter the zone’s 2-digit number or use the [S] and [T] keys and
press the [BYP] key when the zone appears on-screen.
4) Press [ENTER] key to exit.
For Grafica Keypads:
1) Enter their [ACCESS CODE].
2)
3)
4)
Using the scroll keys, highlight Bypass and then press the center
action key (Ok).
Highlight the zone that you wish to bypass and then press the left
action key (Bypass). Repeat this step for any additional zone.
Press the right action key (Back) to save the data.
Users can also activate Bypass Recall. Bypass Recall reinstates all the
zones that were bypassed the last time the partition(s) assigned to the User
Access Code were armed. To activate Bypass Recall, users:
For LCD Keypads:
1) Enter their [ACCESS CODE].
2) Press the [BYP] key.
3) Press the [MEM] key.
4) Press [ENTER] key to exit.
For Grafica Keypads:
1) Enter their [ACCESS CODE].
2) Using the scroll keys, highlight Bypass and then press the center
action key (Ok).
3) Highlight Bypass Recall and then press the center action key (Ok).
For LED Keypads:
Modify Backlight only:
1) Enter an [ACCESS CODE].
2) Press the [6] key.
3) Use the [S] and [T] keys to increase or decrease the illumination.
The range is between zero and seven with seven as the brightest ([10]
LED = zero).
15.10 EVENT RECORD DISPLAY
The Event Record Display displays the user-initiated events that occurred
in the system as well as any alarms or troubles. The events from all the
partitions can scroll on the screen or can be viewed by partition. The most
recent event is displayed first. The Event Record Display can only be
viewed through an LCD or Grafica keypad. To view the events:
For LCD Keypads:
1) Enter a User Access Code
2) Press the [7] key
3) Press
Key Displays:
[0]
[1]
[2]
[3]
[4]
15.8 CHIME ZONES (UL NOTE: NOT TO BE USED FOR PERIMETER PROTECTION)
The keypads can emit rapid, intermittent beeps whenever designated
zones within their assigned partitions open or when they open during a time
period. The instructions that follow are for LCD Keypads, for Grafica
keypads, refer to the Grafica Online Manual, which can be downloaded for
free from our Web site at www.paradox.ca.
For LCD keypads:
To program a Chime Zone, users:
1) Enter their [ACCESS CODE].
2) Press the [9] key.
3) Press the [1] key.
4) Enter the zone’s 2-digit number or use the [S] and [T] keys to scroll
the list and press the [ACC] key when the zone appears on-screen.
5) Press [ENTER] key to save.
To program a time period when the Chime Zones are activated, users:
1) Enter their [ACCESS CODE].
2) Press the [9] key.
3) Press the [2] key.
4) Enter the time that keypads will start beeping when Chime Zones are
opened according to the 24-hour clock (i.e. 9PM is 21:00).
5) Enter the time that keypads will stop beeping when Chime Zones are
opened according to the 24-hour clock (i.e. 9PM is 21:00).
6) Press [ENTER] key to save.
4)
5)
All partitions
Partition 1
Partition 2
Partition 3
Partition 4
Key Displays:
[5]
[6]
[7]
[8]
Partition 5
Partition 6
Partition 7
Partition 8
Press the [T] key to view subsequent events
Press the [CLEAR] key to exit
Change the order that the Event Record screens appear by pressing the [7]
key. If you already know the number of the event you want to view, press
the [MEM] key and then enter the event's number.
For Grafica Keypads:
1) Enter their [ACCESS CODE].
2) Using the scroll keys, highlight View Status and then press the center
action key (Ok).
3) Highlight View Events and then press the center action key (Ok). If
the event list appears on the screen go to step 6.
4) Highlight View All Areas or Select Area(s) and then press the center
action key (Ok).
5) If you selected Select Area(s) in step 4, highlight the area you wish to
view and then press the center action key (Ok).
6) Use the scroll keys to scroll through the events.
15.11 SCROLL RESTART (LCD KEYPAD ONLY)
15.9 KEYPAD SETTINGS
The keypad scrolls through the status of its assigned partitions. Press the
[CLEAR] key at any time to return to the beginning of the sequence.
The keypad’s settings can be modified to suit the user’s needs. The
instructions that follow are for LCD and LED keypads only, for Grafica
keypads, refer to the Grafica Online Manual, which can be downloaded for
free from our Web site at www.paradox.ca.
15.12 TROUBLE DISPLAY
For LCD Keypads:
• Scrolling Speed is how long the messages stay on the LCD screen
before moving to the next message.
• Backlight is the illumination behind the keys and the screen.
• Contrast is how dark the characters appear on the LCD screen.
To change the settings:
1) Enter the [USER ACCESS CODE].
2) Press [6].
3) Press [1]: Scrolling Speed from 0 to 10 (10 = slowest)
Press [2]: Backlight from 0 to 7 (7 = brightest)
Press [3]: Contrast from 0 to 4 (4 = most contrast)
4) Use the [S] and [T] keys to increase or decrease the numbers.
5) Press [ENTER].
6) Press [CLEAR] to exit or the [T] key to move to the next setting.
When the system experiences problems or is tampered with, the Trouble
Display appears on the LCD screen. Keypads will only display troubles that
occur in their assigned partition(s). Potential troubles have been sorted into
eight groups. The Group headings are listed below with a brief explanation
of the potential troubles sorted within each group. To view:
To view the Trouble Display on LCD or LED Keypads:
Step 1: Press the [TRBL] key
Step 2: For LEDs: Press the Numerical Symbol corresponding to the
Group heading to view the specific trouble.
For LCDs: Press the number representing the trouble and press
the [S] and [T] keys to view the specific trouble.
To view the Trouble Display on Grafica Keypads:
Step 1: Enter your [ACCESS CODE].
Step 2: Using the scroll keys, highlight Trouble and then press the center
action key (Ok). The trouble(s) will appear by Trouble Group.
DIGIPLEXNE CONTROL PANEL 43
Step 3: If more than one Trouble Group appears, highlight the desired
group before pressing the center action key (View) to view the
specific trouble.
Trouble
Description
Press [7] to display zone(s)
Trouble
Description
GROUP [1]: SYSTEM
[1] AC Failure
[2] Battery Trouble
[3] AUX Current Limit
[4] Bell Current Limit
[5] Bell Absent
[6] ROM Check Error
[7] RAM Check Error
GROUP [8]: CLOCK LOSS
Power failure detected. The system is
running on the backup battery.
The backup battery is disconnected, needs
to be recharged or replaced.
Devices connected to AUX have exceeded
current limits (1.1A). The Auxiliary Output
will shutdown until the trouble is corrected.
The bell or siren has exceeded current
limits (3A). The Bell/Siren Output will
shutdown until the trouble is corrected.
The bell or siren is not connected. When
the bell output is not used, connect a 1kΩ
resistor across the bell output.
The control panel registers a data memory
error. Contact distributor for replacement.
The control panel registers a work memory
error. Contact distributor for replacement.
GROUP [2]: COMMUNICATOR
[1] TLM1
The control panel is unable to access the
main telephone line.
[2] Fail to Communicate 1
[3] Fail to Communicate 2
[4] Fail to Communicate 3
[5] Fail to Communicate 4
The control panel tried all assigned
telephone numbers and failed to contact
the Monitoring Company.
[6] Fail to Communicate PC
The control panel is unable to
communicate with the WinLoad software.
Press [8] to re-program
[2] ROM Check Error
[3] TLM Trouble
[4] Fail to Communicate
[5] Printer Trouble
[6] AC Failure
[7] Battery Failure
[8] Supply Output
A module’s tamper switch was triggered
A module is experiencing a data memory
error. Contact distributor for replacement.
A module is unable to access the
telephone line.
A module failed to communicate with the
Monitoring Company.
The control panel registers a problem with
a printer connected to a Printer Module.
Check printer for problems (paper jam, no
paper, no power, etc.).
Module power failure.
Module's battery is disconnected, needs to
be recharged or needs to be replaced.
Module has exceeded current limits.
GROUP [4]: NETWORK (COMBUS)
[1] Missing Keypad
[2] Missing Module
[3] General Failure
[4] Combus Overload
A keypad is no longer communicating with
the control panel.
A device is no longer communicating with
the control panel.
No communication between the devices
and the control panel.
Too many devices (over 127) are on the
combus.
GROUP [5]: ZONE TAMPER
Press [5] to display zone(s)
Zones displayed were tampered.
GROUP [6]: ZONE LOW BATTERY
Press [6] to display zone(s)
Zone displayed indicates where a wireless
device’s battery needs to be replaced.
Also, the device’s yellow light will flash.
GROUP [7]: ZONE FAULT
44 REFERENCE & INSTALLATION MANUAL
The time and date were reset to default.
Step 1: Press the [8] key
Step 2: Set the hour and minutes according
to the 24-hour clock (i.e. 9AM is
09:00 and 9PM is 21:00).
Step 3: Enter the correct date according to
yyyy/mm/dd.
Step 4: Press [CLEAR] to exit.
If Access Control is enabled in the system and the option Door
Access during Clock Loss is ON (section [3038] option [8]), only the
System Master Code and User Codes with the Master feature
enabled will be able to program the clock. Enter the System Master
or a Master Code, press [TRBL], then continue with the steps above.
15.13 TROUBLE LATCH
SECTION [3033]: OPTION [6]
With the Trouble Latch feature disabled, when a trouble occurs and is
corrected, the trouble is automatically cleared and no longer displayed.
With the Trouble Latch feature enabled, the trouble will remain displayed
until it is manually cleared by the user. To clear the trouble, the user must
enter the trouble display (see section 15.12) and then exit the trouble
display. For LCD and LED keypads, press [CLEAR] to exit. For Grafica
keypads, press the left action key (Back) to exit.
Only troubles that have been corrected can be cleared. If a
trouble has not been corrected, it will continue to be displayed
even if the user tries to clear the trouble by using the method
described above.
GROUP [3]: MODULES
[1] Module Tamper
A smoke detector is experiencing a wiring
problem, needs to be cleaned, or a
wireless device is no longer communicating
with its receiver (supervision loss).
15.14 CLEAR BELL CURRENT LIMIT TROUBLE
SECTION [3030]: OPTION [7]
(Default: OFF) When an activated bell output is shorted, a Bell Current Limit
trouble is displayed and can be sent to the Central Station. This feature
determines how the Bell Current Limit trouble is cleared.
Option
Description
[7]
ON
[7]
OFF
When an activated bell output is shorted, the Bell Current
Limit trouble will remain displayed until it is manually
cleared by the user. The user must clear the trouble
through the trouble display.
When an activated bell output is shorted, the DigiplexNE
control panel will attempt to reactivate the bell output once
every minute for as long as the bell is activated. The Bell
Current Limit trouble is cleared automatically the first time
the control panel does not detect a short when attempting
to reactivate the bell.
UL Note: For UL installations, section [3030] option [7] must be
enabled (ON).
Only troubles that have been corrected can be cleared. If a
trouble has not been corrected, it will continue to be displayed
even if the user tries to clear the trouble through the trouble
display.
16
Event Group
APPENDIX 1: PGM PROGRAMMING TABLE
Event
000
Zone is OK
001
Zone is Open
002
Zone is Tampered
003
Zone is in Fire Loop Trouble
004
005
006
007
008
009
010
011
012
Non-reportable Event
User Code entered on Keypad
User/Card Access on Door
Bypass Programming Access
TX Delay Zone Alarm
Arming with Master
Arming with User Code
Arming with Keyswitch
Special Arming
Feature Group
Feature
Start #
End #
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
000
255 = any Zone #
Zone Numbers
001 to 096
001 to 096
000
TLM Trouble (See NOTE 3 on page 50)
Smoke detector reset
Arm with no entry delay
Arm in Stay mode
Arm in Away mode
Full arm when in Stay mode
Voice module access
Remote control access
PC Fail to communicate
Midnight
NEware User Login
NEware User Logout
User Initiated Call-up
Force Answer
Force Hang up
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
255
Any Non-reportable Event
Not Used
Not Used
000
User Codes 000 to 255
000 to 255
000 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Door Numbers
001 to 032
001 to 032
255
Any door #
Not Used
Not Used
000
One-touch Bypass Programming
000
000
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Zone Numbers
001 to 096
001 to 096
255
Any zone #
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
000
Auto Arming
Arming with WinLoad
Late to Close
000
001
002
000
001
002
DIGIPLEXNE CONTROL PANEL 45
Event Group
012
013
014
015
016
017
018
019
020
021
022
Event
Special Arming (cont’d)
Disarm with Master
Disarm with User Code
Disarm with Keyswitch
Disarm after alarm with Master
Disarm after alarm with User Code
Disarm after alarm with Keyswitch
Alarm Cancelled with Master
Alarm Cancelled with User Code
Alarm Cancelled with Keyswitch
Special Disarming
46 REFERENCE & INSTALLATION MANUAL
Feature Group
Feature
Start #
End #
000
No Movement Arming
Partial Arming
One-touch Arming
Future Use
Future Use
(InTouch) Voice Module Arming
003
004
005
006
007
008
003
004
005
006
007
008
255
Any special arming event
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
000
Auto Arm Cancelled
One-touch Stay/Instant Disarm
Disarming with WinLoad
Disarming with WinLoad after alarm
WinLoad cancelled alarm
Future Use
Future Use
Future Use
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
Event Group
Event
Feature Group
Feature
Start #
000
(InTouch) Voice Module Disarming
008
End #
008
255
Any Special Disarming Event
Not Used
Not Used
022
Special Disarming (cont’d)
023
Zone Bypassed
001 to 096
001 to 096
024
Zone in Alarm
001 to 096
001 to 096
000
255 = any zone #
Zone Numbers
025
Fire Alarm
001 to 096
001 to 096
026
Zone Alarm Restore
001 to 096
001 to 096
027
Fire Alarm Restore
001 to 096
001 to 096
028
029
030
031
Early to Disarm by User
Late to Disarm by User
Special Alarm
Duress Alarm by User
032
Zone Shutdown
033
Zone Tamper
034
Zone Tamper Restore
035
Special Tamper
036
037
Trouble Event
Trouble Restore
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Emergency Panic (keys 1 & 3)
Medical Panic (keys 4 & 6)
Fire Panic (keys 7 & 9)
Recent Closing
Police Code
Zone Shutdown
000
001
002
003
004
005
000
001
002
003
004
005
255
Any Special Alarm Event
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
001 to 096
001 to 096
001 to 096
001 to 096
000
255 = any zone #
Zone Numbers
001 to 096
001 to 096
000
Keypad Lockout
000
000
000
TLM Trouble (see NOTE 2 on page 50)
AC Failure
Battery Failure
Auxiliary Current Limit
Bell Current Limit
Bell Absent
Clock Trouble
Global Fire Loop
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
255
Any Trouble Event
Not Used
Not Used
000
TLM Trouble (see NOTE 2 on page 50)
AC Failure
Battery Failure
Auxiliary Current Limit
Bell Current Limit
Bell Absent
Clock Trouble
Global Fire Loop
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
255
Any Trouble Restore Event
Not Used
Not Used
DIGIPLEXNE CONTROL PANEL 47
Event Group
038
039
Module Trouble
Module Trouble Restore
040
Fail to Communicate on Telephone
Number
041
Low Battery on Zone
042
Zone Supervision Trouble
043
Low Battery on Zone Restored
044
Zone Supervision Trouble
Restored
045
046
047
†:
Event
Special Events
Early to Arm by User
Late to Arm by User
048
Utility Key
049
Request for Exit
050
Access Denied
051
Door Left Open Alarm
052
Door Forced Alarm
053
Door Left Open Restore
See page 51
*: See page 50
48 REFERENCE & INSTALLATION MANUAL
Feature Group
Feature
Start #
End #
000
Combus Fault
Module Tamper
ROM/RAM error
TLM Trouble
Fail to Communicate
Printer Fault
AC Failure
Battery Failure
Auxiliary Failure
000
001
002
003
004
005
006
007
008
000
001
002
003
004
005
006
007
008
255
Any Module Trouble Event
Not Used
Not Used
000
Combus Fault
Module Tamper
ROM/RAM error
TLM Trouble
Fail to Communicate
Printer Fault
AC Failure
Battery Failure
Auxiliary Failure
000
001
002
003
004
005
006
007
008
000
001
002
003
004
005
006
007
008
255
Any Module Trouble Restore Event
Not Used
Not Used
000
Telephone Number
001 to 004
001 to 004
255
Any telephone number
Not Used
Not Used
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
000
Power up after total power down
Software reset (Watchdog)
Test Report
Future Use
WinLoad In (connected)
WinLoad Out (disconnected)
Installer in programming
Installer out of programming
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
255
Any Special Event
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Utility Key 001 to 064†*
001 to 064
001 to 064
000
255 = any Zone #
255
000
255 = any Door
Number
Zone Numbers
Any Utility
Key†*
Door Numbers
Not Used
Not Used
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
Event Group
Event
054
Door Forced Open Restore
055
Intellizone Triggered
056 to 061
062
063
Future Use
Access Granted to User
Access Denied to User
Feature Group
Feature
Start #
End #
000
255 = any Door
Number
Door Numbers
001 to 032
001 to 032
000
Zone Numbers
001 to 096
001 to 096
255
Any zone number
Not Used
Not Used
Future Use
Future Use
Future Use
Future Use
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
Armed
Force Armed
Stay Armed
Instant Armed
Strobe Alarm
Silent Alarm
Audible Alarm
Fire Alarm
Ready
Exit Delay
Entry Delay
System in Trouble
Alarm in Memory
Zones Bypassed
Bypass, Master, Installer Programming
Keypad Lockout
Intellizone Delay Engaged
(see NOTE 4 on page 50)
Fire Delay Engaged
Auto Arm
Arming with Voice Module (set until
Exit Delay finishes)
Tamper
Zone Low Battery
Fire Loop Trouble
Zone Supervision Trouble
Chime in Partition 1 to 4
(000 to 003 = System 1 to 4)
Smoke Detector Power Reset
Ground Start
Kiss Off
Telephone Ring
Bell on Partition 1 to 8
(008 to 015 = Partitions 1 to 8)
Fire Alarm in Partition 1 to 8
(016 to 023 = Partitions 1 to 8)
Open/close Kiss Off in Partition 1 to 8
(024 to 031 = Partitions 1 to 8)
Keyswitch/PGM Inputs # 01 to 32
(032 to 063 = Keyswitch/PGM Inputs #
01 to 32)
Status of Access Door 01 to 32
(064 to 095 = Access Doors 01 to 32)
Trouble in System
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
000
001
002
003
004
005
006
007
000
000
001
002
001
002
003
003
004
005
006
007
004
005
006
007
000 to 003
000 to 003
004
005
006
007
004
005
006
007
008 to 015
008 to 015
016 to 023
016 to 023
024 to 031
024 to 031
032 to 063
032 to 063
064 to 095
064 to 095
096
096
064
Status 1
See NOTE 1
on page 50
065
Status 2
See NOTE 1
on page 50
066
067
Status 3
Special Status
See NOTE 1
on page 50
N/A
DIGIPLEXNE CONTROL PANEL 49
Event Group
Event
Feature Group
Feature
Start #
End #
Trouble in Dialer
Trouble in Module
Trouble in Combus
Future Use
Time and Date Trouble
AC Failure
Battery Failure
Auxiliary Current Limit
Bell Current Limit
Bell Absent
ROM error
RAM error
Future Use
TLM 1 Trouble
Fail to Communicate 1
Fail to Communicate 2
Fail to Communicate 3
Fail to Communicate 4
Fail to Communicate with PC
Future Use
Future Use
Module Tamper Trouble
Module ROM error
Module TLM error
Module Failure to Communicate
Module Printer Trouble
Module AC Failure
Module Battery Trouble
Module Auxiliary Failure
Missing Keypad
Missing Module
Future Use
Global Combus Failure
Combus Overload
Combus Fail to Communicate
097
098
099
100 to 102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130 to 132
133
134
135
097
098
099
100 to 102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130 to 132
133
134
135
Hour
Minutes
067
Special Status (cont’d)
N/A
070
Clock
N/A
NOTE 1:
000 = Occurs in all partitions enabled in the system (see section [3031]).
001 = Partition 1
003 = Partition 3
005 = Partition 5
007 = Partition 7
002 = Partition 2
004 = Partition 4
006 = Partition 6
008 = Partition 8
255 = Occurs in at least one partition enabled in the system.
NOTE 2:
This TLM trouble event can only be used with the DigiplexNE control panel models that have two dialers.
NOTE 3:
This TLM trouble can only be used with DigiplexNE control panel models that have one dialer.
NOTE 4:
This event cannot be used for a module’s PGM programming.
*:
If a Keyswitch Input is used, the input must be defined as “Generates a Utility Key Event on Open” or “Generates a Utility Key Event on Open
and Close”. If a remote control is used, the remote control button must be defined as a Utility Key button.
50 REFERENCE & INSTALLATION MANUAL
†
:
Table 14: Actions that Generate a Utility Key Event
Actions
Utility Key Event
Keypad Utility Keys
Keyswitch Inputs
(definition = [3])
Keyswitch Inputs
(definition = [4])
Remote Control
Utility Key Event 1
[1] & [2]
KS** Input 1 opens
KS** Input 1 opens
Utility Key 1 RC button‡
Utility Key Event 2
[4] & [5]
KS** Input 2 opens
KS** Input 1 closes
Utility Key 2 RC button‡
Utility Key Event 3
[7] & [8]
KS** Input 3 opens
KS** Input 2 opens
Utility Key 3 RC button‡
Utility Key Event 4
[CLEAR] & [0] or [*] & [0]
KS** Input 4 opens
KS** Input 2 closes
Utility Key 4 RC button‡
Utility Key Event 5
[2] & [3]
KS** Input 5 opens
KS** Input 3 opens
Utility Key 5 RC button‡
Utility Key Event 6
[5] & [6]
KS** Input 6 opens
KS** Input 3 closes
N/A
Utility Key Event 7
[8] & [9]
KS** Input 7 opens
KS** Input 4 opens
N/A
Utility Key Event 8
[0] & [ENTER] or [0] & [#]
KS** Input 8 opens
KS** Input 4 closes
N/A
Utility Key Event 9
N/A
KS** Input 9 opens
KS** Input 5 opens
N/A
Utility Key Event 10
N/A
KS** Input 10 opens
KS** Input 5 closes
N/A
Utility Key Event 11
N/A
KS** Input 11 opens
KS** Input 6 opens
N/A
Utility Key Event 12
N/A
KS** Input 12 opens
KS** Input 6 closes
N/A
Utility Key Event 13
N/A
KS** Input 13 opens
KS** Input 7 opens
N/A
Utility Key Event 14
N/A
KS** Input 14 opens
KS** Input 7 closes
N/A
Utility Key Event 15
N/A
KS** Input 15 opens
KS** Input 8 opens
N/A
Utility Key Event 16
N/A
KS** Input 16 opens
KS** Input 8 closes
N/A
Utility Key Event 17
N/A
KS** Input 17 opens
KS** Input 9 opens
N/A
Utility Key Event 18
N/A
KS** Input 18 opens
KS** Input 9 closes
N/A
L
N/A
L
L
N/A
Utility Key Event 31
N/A
KS** Input 31 opens
KS** Input 16 opens
N/A
Utility Key Event 32
N/A
KS** Input 32 opens
KS** Input 16 closes
N/A
Utility Key Event 33
N/A
N/A
KS** Input 17 opens
N/A
Utility Key Event 34
N/A
N/A
KS** Input 17 closes
N/A
L
N/A
N/A
L
N/A
Utility Key Event 63
N/A
N/A
KS** Input 32 opens
N/A
Utility Key Event 64
N/A
N/A
KS** Input 32 closes
N/A
** Keyswitch
‡ Refer to the Omnia™ Reference and Installation Manual for remote control button programming instructions.
DIGIPLEXNE CONTROL PANEL 51
17
APPENDIX 2: AUTOMATIC REPORT CODE LIST
Default Contact ID Report Code
for sections [4032] to [4037]
Default SIA Report Code
for sections [4032] to [4037]
Arming with Master Code (##)
3 4A1 - Close by user
CL - Closing Report
Arming with User Code (##)
3 4A1 - Close by user
CL - Closing Report
Arming with Keyswitch (##)
3 4A9 - Keyswitch Close
CS - Closing Keyswitch
Auto Arming
3 4A3 - Automatic Close
CA - Automatic Closing
Arm with PC software
3 4A7 - Remote arm/disarm
CQ - Remote Arming
Late To Close
1 4A4 - Late to Close
OT - Late to Close
No Movement
1 4A4 - Late to Close
NA - No Activity
Partial arming
1 456 - Partial Arm
CG - Close Area
Quick arming
3 408 - Quick arm
CL - Closing Report
Disarm with Master Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm with User Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm with Keyswitch (##)
1 4A9 - Keyswitch Open
OS - Opening Keyswitch
Disarm after alarm with Master Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm after alarm with User Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm after alarm with Keyswitch (##)
1 4A1 - Keyswitch Open
OS - Opening Keyswitch
Cancel alarm with Master Code (##)
1 4A6 - Open by user
OR - Disarm From Alarm
Cancel alarm with User Code (##)
1 4A6 - Open by user
OR - Disarm From Alarm
Cancel alarm with Keyswitch (##)
1 4A6 - Keyswitch Open
OS - Opening Keyswitch
System Event
Auto Arming Cancellation
1 464 - Auto-Arm Time Extended
CE - Closing Extend
Disarm with PC software
1 4A7 - Remote arm/disarm
OQ - Remote Disarming
Disarm after an alarm with PC software
1 4A7 - Remote arm/disarm
OR - Disarm From Alarm
Quick Disarm
1 408 - Quick Disarm
OP - Opening Report
Zone Bypassed (##)
1 57A - Zone bypass
UB - Untyped Zone Bypass
Zone alarm (##)
1 13A - Burglary Alarm
BA - Burglary Alarm
Fire alarm (##)
1 11A - Fire alarm
FA - Fire Alarm
Zone alarm restore (##)
3 13A - Burglary Alarm Restore
BH - Burglary Alarm Restore
Fire alarm restore (##)
3 11A - Fire alarm Restore
FH - Fire Alarm Restore
24Hr Gas alarm (##)
1 13A - Burglary Alarm
GA - Gas Alarm
24Hr Heat alarm (##)
1 13A - Burglary Alarm
KA - Heat Alarm
24Hr Water alarm (##)
1 13A - Burglary Alarm
WA - Water Alarm
24Hr Freeze alarm (##)
1 13A - Burglary Alarm
ZA - Freeze Alarm
24Hr Gas alarm restore (##)
1 13A - Burglary Alarm
GR - Gas Alarm Restore
24Hr Heat alarm restore (##)
1 13A - Burglary Alarm
KR - Heat Alarm Restore
24Hr Water alarm restore (##)
1 13A - Burglary Alarm
WR - Water Alarm Restore
24Hr Freeze alarm restore (##)
1 13A - Burglary Alarm
ZR - Freeze Alarm Restore
Police Code
1 139 - Burglary Alarm
BM - Burglary Alarm
Panic 1 - Emergency
1 12A - Panic alarm
PA - Panic Alarm
Panic 2 - Medical
1 1AA - Medical alarm
MA - Medical Alarm
Panic 3 - Fire
1 115 - Pull Station
FA - Fire Alarm
Recent closing
3 4AA - Open/Close
CR - Recent Closing
Global zone shutdown
1 574 - Group bypass
CG - Close Area
Duress alarm
1 121 - Duress
HA - Hold-up Alarm
Zone shutdown (##)
1 57A - Zone bypass
UB - Untyped Zone Bypass
Zone tampered (##)
1 144 - Sensor tamper
TA - Tamper Alarm
Zone tamper restore (##)
3 144 - Sensor tamper restore
TR - Tamper Restoral
Keypad Lockout
1 421 - Access denied
JA - User Code Tamper
AC Failure
1 3A1 - AC loss
AT - AC Trouble
Battery Failure
1 3A9 - Battery test failure
YT - System Battery Trouble
Auxiliary supply trouble
1 3AA - System trouble
YP - Power Supply Trouble
Bell output current limit
1 321 - Bell 1
YA - Bell Fault
Bell absent
1 321 - Bell 1
YA - Bell Fault
Clock lost
1 626 - Time/Date inaccurate
JT - Time Changed
Fire loop trouble
1 373 - Fire trouble
FT - Fire Trouble
TLM trouble restore
3 351 - Telco 1 fault restore
LR - Phone Line restoral
52 REFERENCE & INSTALLATION MANUAL
System Event
Default Contact ID Report Code
for sections [4032] to [4037]
Default SIA Report Code
for sections [4032] to [4037]
AC Failure restore
3 3A1 - AC loss restore
AR - AC Restoral
Battery Failure restore
3 3A9 - Battery test restore
YR - System Battery Restoral
Auxiliary supply trouble restore
3 3AA - System trouble restore
YQ - Power Supply restored
Bell output current limit restore
3 321 - Bell 1 restore
YH - Bell Restored
Bell absent restore
3 321 - Bell 1 restore
YH - Bell Restored
Clock programmed
3 625 - Time/Date Reset
JT - Time Changed
Fire loop trouble restore
3 373 - Fire trouble restore
FJ - Fire Trouble Restore
Combus fault
1 333 - Expansion module failure
ET - Expansion Trouble
Module tamper
1 145 - Expansion module tamper
TA - Tamper Alarm
Module ROM_RAM_error
1 3A4 - Rom checksum bad
YF - Parameter Checksum Fail
Module TLM trouble
1 352 - Telco 2 fault
LT - Phone Line trouble
Module fail to communicate to central station
1 354 - Fail to communicate
YC - Communication Fails
Printer fault
1 336 - Local printer failure
VT - Printer Trouble
Module AC Failure
1 3A1 - AC loss
AT - AC Trouble
Module battery failure
1 3A9 - Battery test failure
YT - System Battery Trouble
Module Auxiliary supply trouble
1 3AA - System trouble
YP - Power Supply Trouble
Combus fault restore
3 333 - Expansion module failure restore
ER - Expansion Restoral
Module tamper restore
3 145 - Expansion module tamper restore
TR - Tamper Restoral
Module ROM_RAM_error restore
3 3A4 - Rom checksum bad restore
YG - Parameter Changed
Module TLM restore
3 352 - Telco 2 fault restore
LR - Phone Line Restoral
Printer fault restore
3 336 - Local printer failure restore
VR - Printer Restore
Module AC restore
3 3A1 - AC loss restore
AR - AC Restoral
Module battery restore
3 3A9 - Battery test failure restore
YR - System Battery Restoral
Module Auxiliary supply restore
3 3AA - System trouble restore
YQ - Power Supply Restored
Fail to communicate with central station
1 354 - Fail to communicate
YC - Communication Fails
Module RF low battery
1 384 - RF transmitter low battery
XT - Transmitter Battery Trouble
Module RF battery restore
3 384 - RF transmitter battery restore
XR - Transmitter Battery Restoral
Module RF supervision trouble
1 381 - Loss of supervision - RF
US - Untype Zone Supervision
Module RF supervision restore
3 381 - Supervision restore - RF
UR - Untyped Zone Restoral
Cold Start
1 3A8 - System shutdown
RR - Power Up
Warm Start
1 3A5 - System reset
YW - Watchdog Reset
Test Report engaged
1 6A2 - Periodic test report
TX - Test Report
PC software communication finished
1 412 - Successful - download access
RS - Remote Program Success
Installer on site
1 627 - Program mode Entry
LB - Local Program
Installer programming finished
1 628 - Program mode Exit
LS - Local Program Success
DIGIPLEXNE CONTROL PANEL 53
18
CID#
APPENDIX 3: CONTACT ID REPORT CODE LIST
Reporting Code
MEDICAL ALARMS - 100
100
Medical Alarm
101
Personal Emergency
102
Fail to Report In
FIRE ALARMS - 110
110
Fire Alarm
111
Smoke
112
Combustion
113
Water Flow
114
Heat
115
Pull Station
116
Duct
117
Flame
118
Near Alarm
PANIC ALARMS - 120
120
Panic Alarm
121
Duress
122
Silent
123
Audible
BURGLAR ALARMS - 130
130
Burglary
131
Perimeter
132
Interior
133
24-Hour
134
Entry/Exit
135
Day/Night
136
Outdoor
137
Tamper
138
Near Alarm
139
Intrusion Verifier
GENERAL ALARMS - 140
140
General Alarm
141
Polling Loop Open
142
Polling Loop Short
143
Expansion Module Failure
144
Sensor Tamper
145
Expansion Module Tamper
24-HOUR NON-BURGLARY - 150 & 160
150
24-Hour Non-Burglary
151
Gas Detected
152
Refrigeration
153
Loss of Heat
154
Water Leakage
155
Foil Break
156
Day Trouble
157
Low Bottled Gas Level
158
High Temperature
159
Low Temperature
161
Loss of Air Flow
FIRE SUPERVISORY - 200 & 210
200
Fire Supervisory
201
Low Water Pressure
202
Low CO2
203
Gate Valve Sensor
204
Low Water Level
205
Pump Activated
206
Pump Failure
54 REFERENCE & INSTALLATION MANUAL
Prog.
Value
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
CID#
Reporting Code
Prog.
Value
SYSTEM TROUBLES - 300 & 310
300
System Trouble
33
301
AC Loss
34
302
Low System Battery
35
303
RAM Checksum Bad
36
304
ROM Checksum Bad
37
305
System Reset
38
306
Panel Program Changed
39
307
Self-Test Failure
3A
308
System Shutdown
3B
309
Battery Test Failure
3C
310
Ground Fault
3D
SOUNDER/RELAY TROUBLES - 320
320
Sounder Relay
3E
321
Bell 1
3F
322
Bell 2
40
323
Alarm Relay
41
324
Trouble Relay
42
325
Reversing Relay
43
SYSTEM PERIPHERAL TROUBLES - 330 & 340
330
System Peripheral
44
331
Polling Loop Open
45
332
Polling Loop Short
46
333
Expansion Module Failure
47
334
Repeater Failure
48
335
Local Printer Paper Out
49
336
Local Printer Failure
4A
COMMUNICATION TROUBLES - 350 & 360
350
Communication
4B
351
Telco Fault 1
4C
352
Telco Fault 2
4D
353
Long Range Radio
4E
354
Fail to Communicate
4F
355
Loss of Radio Supervision
50
356
Loss of Central Polling
51
PROTECTION LOOP TROUBLES - 370
370
Protection Loop
52
371
Protection Loop Open
53
372
Protection Loop short
54
373
Fire Trouble
55
SENSOR TROUBLES - 380
380
Sensor Trouble
56
381
Loss of Supervision - RF
57
382
Loss of Supervision - RPM
58
383
Sensor Tamper
59
384
RF Transmitter Low Battery
5A
OPEN/CLOSE - 400
400
Open/Close
5B
401
Open/Close by User
5C
402
Group Open/Close
5D
403
Automatic Open/Close
5E
404
Late to Open/Close
5F
405
Deferred Open/Close
60
406
Cancel
61
407
Remote Arm/Disarm
62
408
Quick Arm
63
409
Keyswitch Open/Close
64
CID#
Reporting Code
REMOTE ACCESS - 410
411
Callback Request Made
412
Success - Download Access
413
Unsuccessful Access
414
System Shutdown
415
Dialer Shutdown
ACCESS CONTROL - 420
421
Access Denied
422
Access Report By User
SPECIAL TROUBLES - 450 & 460
450
Exception Open/Close
451
Early Open/Close
452
Late Open/Close
453
Failed to Open
454
Failed to Close
455
Auto-Arm Failed
456
Partial Arm
457
User Exit Error
458
User on Premises
459
Recent Close
461
Wrong Code Entry
462
Legal Code Entry
463
Re-arm after Alarm
464
Auto-Arm Time Extended
465
Panic Alarm Reset
466
Service On/Off Premises
SOUNDER RELAY DISABLES - 520
520
Sounder/Relay Disabled
521
Bell 1 Disable
522
Bell 2 Disable
523
Alarm Relay Disable
524
Trouble Relay Disable
525
Reversing Relay Disable
COMMUNICATION DISABLES - 550 & 560
551
Dialer Disabled
552
Radio Transmitter Disabled
BYPASSES - 570
570
Zone Bypass
571
Fire Bypass
572
24-Hour Zone Bypass
573
Burg. Bypass
574
Group Bypass
TEST/MISC. - 600
601
Manual Trigger Test
602
Periodic Test Report
603
Periodic RF Transmission
604
Fire Test
605
Status Report to Follow
606
Listen-in to Follow
607
Walk Test Mode
621
Event Log Reset
622
Event Log 50% Full
623
Event Log 90% Full
624
Event Log Overflow
625
Time/Date Reset
626
Time/Date Inaccurate
627
Program Mode Entry
628
Program Mode Exit
631
Exception Schedule Change
Prog.
Value
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
19
INDEX
Timer ....................................................................... 19
Sections
Auto-Arming Options ........................................................... 19
Automatic Event Buffer Transmission ....................................... 41
A
AC Failure not Displayed ..................................................... 34
Automatic report code list ..................................................... 52
Access Card .................................................................... 38
Auxiliary Power ...................................................................4
Calculating power consumption ..........................................6
Power Limitations ..........................................................6
Power Supply Connections ...............................................7
Troubles ................................................................... 44
Access Card Assignment ..................................................... 37
Away Arming. See Force Arming
Access Code Length .......................................................... 36
Away Zones. See Force Zones
AC Power ......................................................................... 4
................................................................................... 39
Access Alarm ................................................................... 38
Access Codes .................................................................. 36
Access Control feature ........................................................ 37
B
Access Control Terms ........................................................ 38
Backlight ......................................................................... 43
Access Denied ................................................................. 38
Backup Schedule ............................................................... 39
Access Granted ................................................................ 38
Access Level ................................................................... 38
Battery .............................................................................4
Battery Test .................................................................4
Access Level Assignment .................................................... 37
Battery Charging Current ...................................................... 32
Account Number ............................................................... 26
Baud Rate ....................................................................... 32
Account Number Transmission .............................................. 27
Bell
Bell terminals ...............................................................4
Bell/siren Output ............................................................4
Bell/Siren Output During Fire Alarm ................................... 14
Sirens ........................................................................4
Troubles ................................................................... 43
Activate Card ................................................................... 37
Add Tolerance Windows to Schedules ..................................... 37
Ademco Contact ID ............................................................ 27
Ademco Express ............................................................... 27
Ademco slow ................................................................... 27
Bell Current Limit Trouble, Clearing ......................................... 44
Advanced Technology Zoning (ATZ) ....................................... 13
Bell On Communication Fail .................................................. 30
Alarm
On Door Left Open ...................................................... 40
On Forced Door .......................................................... 40
Bell Squawk ..................................................................... 20
Alarm Transmission Delay. See Delay Alarm Transmission
Alarm Types .................................................................... 15
Alternate Dialing Option ...................................................... 28
Always Force Arm ............................................................. 19
AND Door Access Mode ...................................................... 39
Answer WinLoad ............................................................... 33
Answering Machine Override Delay ........................................ 41
Arming and Disarming Report Schedules .................................. 25
Arming Follows Partition ...................................................... 18
Arming Report Schedule ..................................................... 26
Arming with Access Card
Skip Exit Delay ........................................................... 40
Arming/Disarming Reporting ................................................. 25
Arming/Disarming Schedule Tolerance Window .......................... 26
Assigning Doors ............................................................... 38
Assigning keyswitches to partitions ......................................... 17
ATZ .............................................................................. 13
Audible Alarm ..................................................................
Bell Cut-off Timer ........................................................
Pulsed .....................................................................
Steady .....................................................................
22
21
15
15
Auto Report Code Programming ............................................ 28
Bell/alarm Output ............................................................... 21
Broadcast ........................................................................ 33
Burglar Alarm ................................................................... 38
Burglar Alarm on Door Left Open ............................................ 40
Burglar Alarm On Forced Door ............................................... 40
Burglary Zones ................................................................. 13
Bus Connection in Noisy Environments .......................................9
Bus Speed ....................................................................... 32
Busy Tone Detection ........................................................... 30
Buzzer Zones ................................................................... 13
Bypass Programming .......................................................... 42
Bypass Recall ................................................................... 43
Bypass Zones ................................................................... 14
C
Call Back Feature .............................................................. 41
Call Direction .................................................................... 27
Call WinLoad .................................................................... 33
Cancel Communication ........................................................ 33
Card and Code Access ........................................................ 39
Card can Disarm ............................................................... 37
Card to Unlock and Code to Disarm ......................................... 37
Chime Zone ..................................................................... 43
Auto Test Report Period ...................................................... 28
CleanMe ...........................................................................9
Auto Trouble Shutdown ....................................................... 34
Clear Bell Current Limit Trouble .............................................. 44
Auto Zone Shutdown .......................................................... 14
Clock Compensation Value ................................................... 34
Auto-Arming
No Movement ............................................................ 19
No Movement Timer .................................................... 19
Timed ...................................................................... 18
Clock Loss
Access during Clock Loss .............................................. 40
Closing Delinquency Timer ................................................... 29
Code Access .................................................................... 39
DIGIPLEXNE CONTROL PANEL 55
Code Follows Schedule ....................................................... 37
EOL Zones ...................................................................... 15
Codes
Special Alarm Report Codes ...........................................
Special Arming Report Codes .........................................
Special Disarming Report Codes .....................................
System Trouble Codes .................................................
System Trouble Restore Codes .......................................
Event Buffer
Log Door Forced Open Restore In Event Buffer .................... 40
Log Door Left Open Restore In Event Buffer ........................ 40
Log Request For Exit In Event Buffer ................................. 40
ESL CleanMeTM Installation ...................................................9
25
24
25
25
25
Compensation Value, Clock .................................................. 34
Connecting the Bus in Noisy Environments ................................. 9
Event Group ..................................................................... 31
Event Record Display .......................................................... 43
Everyday arming. See Regular Arming
Connections
Advanced Technology Zone (ATZ) ................................... 13
Bell/siren Output ........................................................... 4
Bus Connections .......................................................... 9
DGP2-ZX4 .................................................................. 8
Double Zone Connections ............................................... 8
Keypad Zone Connections ............................................... 7
Keyswitch Connections ................................................... 4
PGM ......................................................................... 4
Power ....................................................................... 4
Single Zone Connections ................................................. 7
Telephone Line Connections ............................................ 9
Exit Delay ........................................................................ 19
Contact ID Pager .............................................................. 27
Fire Zone ..........................................................................9
Contact ID Report Code ...................................................... 52
Fire Zone, Delayed 24hr. ...................................................... 14
Contact ID Report Code List ................................................. 54
Fire Zone, Standard 24hr. ..................................................... 14
Contrast ......................................................................... 43
Follow zone ..................................................................... 13
Current setting for charging battery ......................................... 32
Follow Zone Switches to Entry Delay 2 ..................................... 19
D
Force Zones ..................................................................... 15
Daylight Savings Time ........................................................ 32
Forced Door ..................................................................... 38
Delay Alarm Transmission ................................................... 15
Freeze Zones ................................................................... 14
Delay Alarm Transmission Timer ............................................ 15
Function Keys, Installer ........................................................ 33
Exit Delay cancelled on Remote Arm ....................................... 20
Exit Delay Termination ........................................................ 19
Extended Unlocked Period .................................................... 37
F
Feature Group .................................................................. 31
Feature Select Programming ................................................. 11
Fire Alarm ....................................................................... 22
Fire Circuits .......................................................................9
Force Arming .................................................................... 42
Delay Between Dialing Attempts ............................................ 28
Delayed 24Hr Fire Zone ...................................................... 14
G
Delinquency Timer, Closing .................................................. 29
Gas Zones ....................................................................... 13
Dial Tone Delay ................................................................ 30
Ground .............................................................................4
Digiplex Memory Key. See Paradox Memory Key
Disarm Reporting Options .................................................... 28
H
Disarming ....................................................................... 42
Hardware Reset ................................................................ 32
Disarming Report Schedule .................................................. 26
Heat Zones ...................................................................... 13
Display “Bypass” If Armed .................................................... 20
Hold-up Zones .................................................................. 13
Door Access Mode ............................................................ 39
Holiday Programming .......................................................... 39
Door Forced Open Restore event ........................................... 40
Hourly Test Transmission ..................................................... 28
Door Labels ..................................................................... 34
Door Left Open ................................................................. 38
I
Doors
Access During Clock Loss .............................................
Assigning The Keypad To A Door ....................................
Burglar Alarm On Door Left Open ....................................
Burglar Alarm On Forced Door ........................................
Identifier code. See Panel Identifier ......................................... 41
40
38
40
40
Input Speed ..................................................................... 15
Double Zone Connections ...................................................... 8
Installer Code ................................................................... 36
Double Verification for Access. See Card and Code Access
Duress ........................................................................... 37
E
Earth Ground ..................................................................... 4
Enable Access Control ........................................................ 38
Enable Arming/Disarming Report Schedules .............................. 25
Enable Reporting .............................................................. 24
End # ............................................................................ 31
Entry Delay Timer ............................................................. 13
Entry Delay Timers ............................................................ 13
Entry Delay zones ............................................................. 13
56 REFERENCE & INSTALLATION MANUAL
Input Numbers
Keyswitch Numbering ................................................... 16
Installation Procedure ............................................................4
Installer Function Keys ........................................................ 33
Installer Lock .................................................................... 32
Installer Test Mode ............................................................. 33
Instant Arming .................................................................. 42
Instant Arming with Delay ..................................................... 42
Instant zone ..................................................................... 13
Intellizone ........................................................................ 15
Intellizone Delay ................................................................ 15
K
Key for Access .................................................................. 39
Keypad Beep on Successful Arm/Disarm Report ......................... 30
PCB Layout .......................................................................5
Keypad Lockout ................................................................ 20
PGM
PGM Activation Event ................................................... 31
PGM Deactivation Event ................................................ 31
PGM Deactivation Option ............................................... 31
PGM Delay Timers ....................................................... 31
PGM Time Base Selection .............................................. 31
Keypad Numbering ............................................................ 15
Keypad Zone Connections ..................................................... 7
Keyswitch
Arm Only .................................................................. 17
Connections ................................................................ 4
Definitions ................................................................ 16
Disabled ................................................................... 16
Keyswitch Numbering ................................................... 16
Maintained ................................................................ 16
Momentary ................................................................ 16
Options .................................................................... 17
Partition Assignment .................................................... 17
Stay/Instant Disarm ..................................................... 17
Keyswitch for PGM Activation ............................................... 17
PGM Programmimg Table .................................................... 45
PGM. See Programmable Outputs
PIN and Card for Access ...................................................... 39
Police Code Timer .............................................................. 21
Power Failure Report Delay .................................................. 28
Power Save Mode .............................................................. 34
Power Supply Connections .....................................................7
Power Unit Consumption Table ................................................6
Primary Schedule .............................................................. 39
L
Problems. See Trouble Display
Label Broadcast ................................................................ 33
Procedure to Install ..............................................................4
Label Programming ........................................................... 34
Programmable Outputs ..........................................................4
As a 2-wire smoke detector ...............................................9
As a 4-wire smoke detector ...............................................9
Connections .................................................................4
Relay .........................................................................4
LCD Display
Keypad Settings ......................................................... 43
Shabbat Feature ......................................................... 33
Linked Schedules. See Backup Schedules
Locate Module ................................................................. 33
Location & Mounting ............................................................ 4
Lock-out ......................................................................... 20
Logging Access Control Events ............................................. 40
Programming .................................................................... 11
Decimal Programming ................................................... 11
Feature Select Method .................................................. 11
Hexadecimal Programming ............................................. 11
Modules ............................................................... 11, 33
Zone Programming ...................................................... 12
M
Pulse Dialing .................................................................... 30
Master ........................................................................... 37
Pulse formats. See Standard Pulse Formats
Maximum Bypass Entries .................................................... 20
Maximum Dialing Attempts ................................................... 28
Message Programming. See Label Programming
Module Broadcast .........................................................11, 33
Module Reset .................................................................. 33
Module Scan ................................................................... 33
Multiple Action Feature ....................................................... 34
N
No AC Fail Display ............................................................ 34
No Bell Cut-Off on Fire Alarm ................................................ 21
No Exit Delay on Remote Arm ............................................... 20
Noisy Environments ............................................................. 9
Pulse Ratio ...................................................................... 30
Pulsed Audible Alarm .......................................................... 15
R
Reader ........................................................................... 38
Recent Close Delay ............................................................ 28
Record REX events ............................................................ 40
Recycle Alarm .................................................................. 21
Recycle Delay ................................................................... 21
Regular Arming ................................................................. 42
Report Only ..................................................................... 15
Report Schedules .............................................................. 25
Reporting Formats ............................................................. 27
Request for Exit ................................................................. 38
O
Request for Exit (REX) event ................................................. 40
One-touch Features ........................................................... 19
Reset
Hardware .................................................................. 32
Module ..................................................................... 33
Software ................................................................... 32
OR Door Access Mode ....................................................... 39
P
Partition Labels ................................................................. 34
Restrict Arming on
AC Failure ................................................................. 18
Battery Failure ............................................................ 18
Bell or Auxiliary Failure .................................................. 18
Door ........................................................................ 40
Module Troubles ......................................................... 18
Supervision Loss ......................................................... 18
Tamper .................................................................... 18
TLM Failure ............................................................... 18
Partitioning ...................................................................... 32
Restrict Disarming on Door ................................................... 40
PC Password ................................................................... 41
Ring Counter .................................................................... 41
PC Telephone Number ....................................................... 41
Ring-back ........................................................................ 20
Pager Format ................................................................... 27
Pager Reporting Format ...................................................... 27
Panel Answer Options ........................................................ 41
Panel Partition Assignment .................................................. 33
Panic Options .................................................................. 22
Paradox Memory Key ......................................................... 11
RTC .............................................................................. 10
DIGIPLEXNE CONTROL PANEL 57
S
U
Schedule Assignment ......................................................... 37
User Access Codes ............................................................ 36
Schedule Tolerance Window ................................................ 39
User Labels. See Access Codes
Schedule Tolerance Window for Arming/Disarming ...................... 26
User Menu Access ............................................................. 37
Schedules ....................................................................... 38
Utility Key ........................................................................ 17
Scroll Restart ................................................................... 43
Scrolling Speed ................................................................ 43
V
Secondary Schedules ......................................................... 39
Valid Card ....................................................................... 38
Serial Port Baud Rate ......................................................... 32
Value, Clock Compensation .................................................. 34
Serial Port Transmission of Zone Status ................................... 32
Sescoa .......................................................................... 27
W
Shabbat Feature ............................................................... 33
Water Zones .................................................................... 14
SIA FSK ......................................................................... 27
WinLoad .................................................................... 11, 41
Answer WinLoad .................................................... 33, 41
Call WinLoad ......................................................... 33, 41
Cancel Communication .................................................. 33
SIA Report Code ............................................................... 52
Silent Alarm .................................................................15, 22
Silent Knight fast ............................................................... 27
Sirens .............................................................................. 4
Skip Exit Delay When Arming With Card ................................... 40
Sleep Mode. See Power Save Mode
Smoke Detector .................................................................. 9
CleanMe feature ........................................................... 9
Special Characters ............................................................ 34
Special Telephone Number Keys ........................................... 26
Speed, Bus ..................................................................... 32
Standard 24Hr Fire Zone ..................................................... 14
Standard Pulse Formats ...................................................... 27
Start # ........................................................................... 31
Stay Arming .................................................................... 42
Stay Arming with Delay ....................................................... 42
Stay Delay zone ............................................................... 14
Stay Zones ...................................................................... 15
Supervision Bypass Options ................................................. 21
Swinger Shutdown. See Auto Zone Shutdown
Switch To Pulse ................................................................ 30
Switch To Stay Arming ........................................................ 19
System Date and Time ........................................................ 33
System Event .................................................................. 52
System Labels ................................................................. 34
System Master Code .......................................................... 36
T
Tamper Bypass Options ...................................................... 22
Telephone Line Connection Examples ....................................... 9
Telephone Line Connections .................................................. 9
Telephone Line Monitoring (TLM) ........................................... 30
Test Report ..................................................................... 33
Test reports ..................................................................... 28
Timed Test Transmission when Armed/Disarmed ........................ 28
TLM Fail Timer ................................................................. 30
Tolerance Window .........................................................26, 39
Tone/DTMF format ............................................................ 30
Transformer ...................................................................... 4
Transmit Zone Status on Serial Port ........................................ 32
Trouble Display ................................................................ 43
Trouble Latch ................................................................... 44
Troubles ......................................................................... 43
58 REFERENCE & INSTALLATION MANUAL
Wireless Transmitter Supervision Options .................................. 21
Z
Zone Labels ..................................................................... 34
Zone Restore Report Options ................................................ 28
Zone Status Transmission to Serial Port .................................... 32
Zones
24Hr Burglary zone ...................................................... 13
24Hr Buzzer ............................................................... 13
24Hr Freeze zone ........................................................ 14
24Hr Gas zone ........................................................... 13
24Hr Heat zone ........................................................... 13
24Hr Hold-up zone ....................................................... 13
24Hr Water zone ......................................................... 14
Alarm Transmission Delay .............................................. 15
Bypass ..................................................................... 14
Connections .................................................................7
Definition .................................................................. 13
Delayed 24Hr Fire Zone ................................................. 14
Disabled ................................................................... 13
Doubling ................................................................... 13
Entry Delay ................................................................ 13
EOL ........................................................................ 15
Follow ...................................................................... 13
Force Zone ................................................................ 15
Generates a report only ................................................. 15
Input Speed ............................................................... 15
Instant ...................................................................... 13
Intellizone .................................................................. 15
Partition Assignment ..................................................... 14
Pulsed Audible Alarm .................................................... 15
Silent Alarm ............................................................... 15
Standard 24Hr Fire Zone ................................................ 14
Stay Delay zone .......................................................... 14
Stay Zone ................................................................. 15
Steady Audible Alarm ................................................... 15
Zone Doubling (ATZ) .................................................... 13
Zone Options ............................................................. 14
20
WARNINGS
FCC Warnings
UL and ULC Warnings
IMPORTANT INFORMATION
UL AND C-UL INSTALLATION NOTES
This equipment complies with Part 68 of the FCC rules subpart D and CS-03. Inside
the cover of this equipment is a label that contains, among other information, the FCC
registration number of this equipment.
The control panel (DGP-NE96) and LCD Keypad (DGP2-641) are UL listed in
accordance with standard UL1023 (Household Burglar -- Alarm Systems Units),
standard UL985 (Household Fire Warning Units), standard UL1635 (Digital Alarm
Communicator System Units), standard UL609 (Local Burglar Alarm Units and
Systems), standard UL365 (Police Station Connected Burglar Alarm Units and
Systems) and standards UL1610 (Central Station Burglar Alarm Units). This
equipment has the capability of being programmed with features and connected to
modules not verified for use in UL installations. To stay within these standards, the
installer should use the following guidelines when configuring the system:
•
All components of the system should be UL listed for the intended application.
•
If the system will be used for “Fire” detection, the installer should refer to NFPA
Standards #72, Chapter 2. In addition, once installation is complete, the local fire
authority must be notified of the installation.
•
This equipment must be verified by a qualified technician once every three
years.
•
All keypads must use a tamper switch.
•
Maximum allowed entry delay is 45 seconds.
•
Maximum allowed exit delay is 60 seconds.
•
Minimum 4 minutes for bell cut-off time.
•
The following features do not comply with UL requirements: Bypass Recall,
Shabbat, Auto Trouble Shutdown, and “No AC Fail” display.
•
Do not connect the primary indicating device to a relay. The installer must use
the bell output.
•
All modules installed on the system must be UL listed in accordance with the
standards listed above.
•
The metallic enclosure must be grounded to the cold water pipe.
•
The DGP2-ZX4 is not approved for UL systems.
NOTIFICATION TO TELEPHONE COMPANY
Upon request, customer shall notify telephone company of particular line to which the
connection will be made and provide the FCC registration number and the ringer
equivalence of the protective circuit.
FCC REGISTRATION NUMBER:
RINGER EQUIVALENCE NUMBER:
USOC JACK:
5A7CAN-22633 - AL - E
0.1B (U.S. & CANADA)
RJ31X (USA), CA31A
(CANADA)
TELEPHONE CONNECTION REQUIREMENTS
Except for telephone company provided ringers, all connections to the telephone
network shall be made through standard plugs and telephone company provided
jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection of
terminal equipment. Standard jacks shall be so arranged that, if plug connected
thereto is withdrawn, no interference to operation of equipment at customer's premises
which remains connected to telephone network shall occur by reason of such
withdrawal.
INCIDENCE OF HARM
Should terminal equipment/protective circuitry cause harm to telephone network,
telephone company shall, where practicable, notify customer that temporary
disconnection of service may be required; however, where prior notice is not
practicable, the telephone company may temporarily discontinue service if action is
deemed reasonable in circumstances. In case of temporary discontinuance, telephone
company shall promptly notify customer and will be given opportunity to correct the
situation.
CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The telephone company may make changes in its communication facilities, equipment
operations or procedures, where such actions are reasonably required and proper in
its business. Should any such changes render customer's terminal equipment
incompatible with the telephone company facilities, the customer shall be given
adequate notice to effect the modifications to maintain uninterrupted service.
GENERAL
This equipment shall not be used on coin telephone lines. Connection to party line
service is subject to state tariffs.
RINGER EQUIVALENCE NUMBER (REN)
The REN is useful to determine the quantity of devices that you may connect to your
telephone line and still have all of those devices ring when your telephone number is
called. In most, but not all areas, sum of the REN's of all devices connected to one line
should not exceed five (5). To be certain of the number of devices that you may
connect to your line, you may want to contact your local telephone company.
For further details concerning the above information, refer to the UL standards listed
and/or the Underwriters Laboratories Inc. Standard for Safety‘s Installation and
Classification of Burglar and Holdup Alarm Systems.
Recommended:
•
•
•
•
All outputs are Class 2 or power-limited, except for the battery terminal.The Class 2
and power-limited fire alarm circuits shall be installed using CL3, CL3R, CL3P, or
substitute cable permitted by the National Electrical Code, ANSI/NFPA 70.
The control unit and keypads are intended to be programmed and installed as follows:
EQUIPMENT MAINTENANCE FACILITY
If you experience trouble with this telephone equipment, please contact facility
indicated below for information on obtaining service or repairs. The telephone
company may ask that you disconnect this equipment from network until problem is
corrected or until you are sure that the equipment is not malfunctioning.
•
•
•
FCC PART 15, WARNINGS: INFORMATION TO USER
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
equipment intermittently, the user is encouraged to try to correct the interference by
one or more of the following measures: (1) reorient or relocate the receiving antenna;
(2) increase the separation between the equipment and receiver; (3) connect the
equipment to an outlet on a circuit other than the one to which the receiver is
connected, or (4) consult the dealer or an experienced radio/tv technician for
assistance.
CAUTION:
Changes or modifications not expressly approved by PARADOX SECURITY
SYSTEMS could void the user's authority to operate the equipment.
EOL resistor part #2011002000
Transformers: (A) ATC Frost #FTC3716 16.5Vac, 37VA; (B) ATC Frost
#FPS4016 16.5Vac, 40VA; (C) Basler Electronics model #BE156240CAA
16.5Vac (50/60Hz), 20VA or 40VA.
For CSA listed systems, use Basler Electronics’ transformer model
#BE116240AAA.
12Vdc 4Ah rechargeable acid/lead or gel cell backup battery (YUASA model
#NP7-12 recommended) for residential use. 7Ah battery to comply with fire
requirements.
•
•
•
•
•
•
•
•
•
Household Fire Warning Systems (US and Canada)
At least one model DGP2-641 keypad shall be used with the system.
One Paradox model MR3-UL end-of-line supervision relay. The relay is intended
to provide supervision of the smoke detector power circuit.
One listed audible device rated to operate over the range of 11.4 to 12.5Vdc and
rated 85db minimum is required for this application. For example, Wheelock
model 46T-12 is compatible. The bell cutoff time shall be programmed for a
minimum of 4 minutes (5 minutes for Canada).
The fire alarm initiating circuit shall employ the listed model 2011002000-PRT
end-of-line resistor.
For Canadian systems, the secure screw for the listed Class 2 transformer shall
not be employed.
Household Grade A Burglar Alarm system Unit (US and Canada)
At least one listed audible device rated to operate over the range of 11.4 to
12.5Vdc and rated 85db minimum. For example, Wheelock model 46T-12 is
compatible.
At least one model DGP2-641 keypad shall be used.
All initiating circuits shall be programmed and installed as end-of-line
supervised.
Burglar alarm initiating devices shall be rated to operate over the range of 11.4 to
12.5Vdc.
The bell cutoff time shall be programmed for a minimum of 4 minutes.
The maximum entry delay shall not exceed 60 seconds. The maximum exit
delay shall not exceed 45 seconds.
For Canadian systems, the secure screw for the listed Class 2 transformer shall
not be employed.
DIGIPLEXNE CONTROL PANEL 59
Grade B Central Station (Level 0)
Same as Household Grade A Burglar alarm system unit except:
•
The ringback feature shall be enabled (section [3037] option [5]; page 30).
•
The model AB12M Bell and Bell Housing, manufactured by ADEMCO shall be
employed. Bell cutoff time shall be programmed for a minimum of 15 minutes (30
minutes for Canada).
•
The Auto Test Report setting must be programmed to send a test transmission to
the central station at least once every 24 hours (section [3037] options [3] and
[4] on page 28 and section [3041] on page 28).
•
Openings and closings must be reported to the central station. Report codes
shall be enabled.
•
Model 278-0000-035 attack resistant enclosure must be employed.
Grade C Central Station (Level 0)
Same as Grade B Central Station except the Grade A Bell housing may not be
employed.
Grade A Local Alarm Units (Level 0)
Same as Grade B Central Station except:
•
Bell test must be enabled.
Police Station Connect with Basic Line Security (Level 0)
Same as Grade B Central Station except:
•
Openings and closings may not be reported to the central station.
•
•
Access Control System
At least one model DGP2-641AC keypad shall be used with the system.
The listed compatible model PosiProx reader shall be employed off the keypad.
Control of the Protected Premise
In order to have a UL certified system, the protected area is to be under the
responsibility of one ownership and management (i.e. one business under one name).
This may be a group of buildings attached or unattached with different addresses but
under the responsibility of someone having mutual interest. The person of mutual
interest is not the alarm installing company.
Bell Location
The alarm sounding device (bell) must be located where it can be heard by the person
or persons responsible for maintaining the security system during the daily arming
cycle.
Protection of the Control Unit
The local control unit and the local power supply must be protected by one of the
following ways:
•
The control unit and audible alarm device must be in a protected area, which is
armed 24 hours a day.
•
Each partition shall arm the area protecting the control unit and the audible
alarm device power supply. This may require duplicate protection armed by each
partition. Access to this protected area, without causing an alarm, will require
that all partitions be disarmed
In all cases described above, the protected area for the control unit must be
programmed as not bypassable.
CTR-21 Warnings
The equipment has been approved in accordance with Council Decision 98/482/EC for
pan-European single terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual PSTNs provided in
different countries, the approval does not, of itself, give an unconditional assurance of
successful operation on every PSTN network termination point. In the event of
problems, you should contact your equipment supplier in the first instance.
General Warning
This equipment must be installed and maintained by qualified service personnel only.
Warranty
Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects
in materials and workmanship under normal use for a period of one year. Except as
specifically stated herein, all express or implied warranties whatsoever, statutory or
otherwise, including without limitation, any implied warranty of merchantability and
fitness for a particular purpose, are expressly excluded. Because Seller does not
install or connect the products and because the products may be used in conjunction
with products not manufactured by Seller, Seller cannot guarantee the performance of
the security system and shall not be responsible for circumstances resulting from the
product’s inability to operate. Seller obligation and liability under this warranty is
expressly limited to repairing or replacing, at Seller's option, any product not meeting
the specifications. Returns must include proof of purchase and be within the warranty
period. In no event shall the Seller be liable to the buyer or any other person for any
loss or damages whether direct or indirect or consequential or incidental, including
without limitation, any damages for lost profits stolen goods, or claims by any other
party, caused by defective goods or otherwise arising from the improper, incorrect or
otherwise faulty installation or use of the merchandise sold.
60 REFERENCE & INSTALLATION MANUAL
Notwithstanding the preceding paragraph, the Seller’s maximum liability will be strictly
limited to the purchase price of the defective product. Your use of this product signifies
your acceptance of this warranty.
*BEWARE: Dealers, installers and/or others selling the product are not authorized to
modify this warranty or make additional warranties that are binding on the Seller.
ATTACHMENT LIMITATION NOTICE
The Industry Canada label identifies certified equipment. This certification means that
the equipment meets certain telecommunications network protective, operational and
safety requirements. The Department does not guarantee the equipment will operate
to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electrical inspection authority, or electrician, as
appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of
the total load to be connected to a telephone loop which is used by the device to
prevent overloading. The termination on a loop may consist of any combination of
devices subject only to the requirement that the total of the Load Numbers of all of the
devices does not exceed 100.
Industry Canada certification is only applicable to installation of devices which include
transformers approved by the Canadian Standards Association (CSA).
© 2002-2003 Paradox Security Systems Ltd.
DigiplexNE, WinLoad, NEware, Omnia and InTouch are trademarks or
registered trademarks of Paradox Security Systems Ltd. and its affiliates in
Canada, the United States and/or other countries. All rights reserved.
PosiPIN is a trademark or registered trademark of Position Technology Inc.
and its affiliates in Canada, the United States and/or other countries. All
rights reserved.
Printed in Canada - 01/2004
DGPNE96-EI07
Download PDF

advertising