® Model No. WLTL11090 Serial No. USER'S MANUAL Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our Customer Hot Line will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST www.weslo.com new products, prizes, fitness tips, and much more! TABLE OF CONTENTS IMPORTANT PRECAUTIONS ................................................................. BEFORE YOU BEGIN ....................................................................... ASSEMBLY ............................................................................... OPERATION AND ADJUSTMENT ............................................................. HOW TO FOLD AND MOVE THE TREADMILL .................................................. MAINTENANCE AND TROUBLE-SHOOTING ................................................... CONDITIONING GUIDELINES ............................................................... ORDERING REPLACEMENT PARTS .................................................. LIMITED WARRANTY ............................................................... Note: An EXPLODED for future reference. IMPORTANT DRAWING and a PART LIST are attached in the center of this manual. Please save them PRECAUTIONS away from the treadmill atall times. 7. The treadmill should not belused by persons weighing more than 250 pounds. 8. Never allow more than one person on the treadmil at atime. 9. Wear appropriate exercise clothing when using the treadmill• Do not wear loose clothing that could become caught in the treadmill, Athletic support clothes are recommended for 2 2 4 5 7 10 12 14 Back Cover Back Cover ing 15. The treadmill Adjust the s sudden 16. Never leave the treadmill unattended while it is running. Always remove the key and unplug the power cord when the treadmill is not in use. 21. Never drop or insert any object into any opening. 22.DANGER: Always Unplug thepower 17 Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 5, and HOW TO MOVE THE TREADMILL on page 10.) You must be able to safely lift 45 pounds (20 kgl in order to raise, lower, or move the treadmill. 18 Do not change the incline of the treadmi I by placing objects under the treadmill. 19. When folding or moving the treadmill, make sure that the storage latch is fully closed, cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual, Never remove the motor hood unless instructed to do so by an authorized service representative, Servicing other than the procedures in this manual should be performed by an authorized service representative only. only, DO not use this treadmill in any commercial, rental, or institutional setting. 20. Inspect and tighten all parts of the treadmill regularly_, ii_!!!ii_!i!i!i!i;!: :i_;ii!ili_ ! i WAR _ai i NI NG _ Before insiructioh_ bef_r_ us u S!_inedb_ beg,nn!ng tf!_s o_;any exerp!s:e prgg_am consu!t ¥0uF ph_s iCO_ __i_ _rodu_ The decals shown have been placed on your treadmill. If a decal is missing, or if it is not legible, please call our Customer Service Department, toll-free, to order a free replacement decal (see ORDERING REPLACEMENT PARTS on the back cover of this manual). Apply the decal in the location shown. Note: The decal below is shown at 38% of actual size. 3 BEFORE YOU BEGIN Thank you for selecting the WESLO ®CADENCE DX3 treadmill. The CADENCE DX3 treadmill combines advanced technology with innovative design to let you enjoy an excellent form of cardiovascular exercise in the convenience and privacy of your home. And when you're not exercising, the unique CADENCE DX3 can be folded up, requiring less than half the floor space of other treadmills. please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is WLTL11090. The serial number can be found on a decal attached to the tread- For your benefit, read this manual carefully before using the treadmill. If you have additional questions, Before reading further, please review the drawing below and familiarize yourself with the labeled parts. mill (see the front cover of this manual for the location). Water Bottle Holder (Bottle not included) Console Handrail Key/Cli LEFT SIDE RIGHT SIDE Hood Grip Tape Breaker Walking Belt Rear Roller Adjustment Bolt 4 .Front Wheel ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrenc-_ two adjustable wrenches _ and your own phillips screwdriver and 9/16 socket wrench _ (_ . 1. With the help of a second person, carefully raise the Right and Left Handrails (6, 7) to the position shown. Be carefuT not to pull on the Wire Harness (22) as you raise the Uprights. 2. With the help of a second person, carefully tip the treadmill onto its right side. Hold the Base (80) against the Left Upright (7) and the Right Upright (not shown). Make sure the Base Pads (19) are on the bottom. , 22 2 Using a 9/16 socket wrench and an adjustable wrench, attach the Base (80) to the Left Upright (7) with two Upright Bolts (84), two Washers (11), and two Upright Nuts (17). Do not tighten the Upright Bolts yet. Attach the Base to the Right Upright (not shown) with two Upright Bolts (12), two Washers (11 ), and two Upright Nuts (17). Then, tighten all four Upright Bolts (84). 84 7 11 Tip the treadmill back to the position shown in step 1. 3. Insert the Wire Harness (22) into the Right Upright (7) as you insert the Handrail (16) into the Right and Left Uprights (7, 6). Be careful not to pinch the Wire Harness. Tighten a Handrail Bolt (12) with a Washer (11) into each Upright. 3 16 Loosen the two Console Bolts (9) underneath the Console (1). Rotate the Console to the position shown and tighten the two Console Bolts. 5 4. Using two adjustabre wrenches, attach the Wheels (15) to the Base (80) with the two Wheel Bolts (14) and the two Wheel Nuts (42) as shown. Do not overtighten the Bolts. The Wheels should turn freely. 4 14 5. Note: You must be able to safely lift 45 pounds (20 kg) in order to do this step. 5 Hold the treadmill with your hands in the locations shown. Caution: To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill to the vertical position. 6. Make sure that the Latch Pin (78) is placed in the Storage Latch (77) as shown. 6 ;I 55-- Attach the Storage Latch (77) to the Frame (55) with the three Screws (5). Do not fully tighten the Screws yet. Position the Latch so that the Latch Pin (78) is aligned with the hole in the Left Upright (7). Slide the Latch Pin into the hole as shown in the inset drawing. Then, tighten the three Screws. / 77,. Hole// 7. The console requires two "AA" batteries (not included). Alkaline batteries are recommended. To install batteries, first touch the Handrail (16) to discharge any static. Next, open the Battery Cover (8). Press the batteries into the battery compartment, with the negative (-) ends of the batteries touching the springs. Close the battery cover, push up on the tab, and then push the tab forward as shown in the inset drawing. Be sure that the tab locks into place. 7 8 Batteries_/ Battery Cover Tab 8. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place amat under the treadmill. OPERATION THE PERFORMANT AND ADJUSTMENT LUBE TM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBE TM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. They will deteriorate the walking belt and cause excessive wear. electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge protector to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available. HOW TO PLUG IN THE POWER CORD The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician. The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is grounded before using an adapter. Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home's power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your tread1 7Grounded Outlet Box mill being damaged, always use a surge protector (not inGrounding Pin cluded) with your treadmill. "_ounding Surge protectors are sold at most hardware stores and department stores. Use only a ULlisted surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length. This product must be grounded. If it should malfunction or break Treadmill Power Cord_. Grounding Plug_ Plug _Grounded Outlet Surge Protector down, grounding provides a path of least resistance for electric current to reduce the risk of 7 DIAGRAM OF THE CONSOLE Monitor Display Water Bottle Holder Speed Control (Water bottle is not included) STEP BY STEP CONSOLE OPERATION U Before the console can be operated, two "AA" batteries must be installed (see assembly step 6 on page 6). Follow the steps below to operate the console. Step onto the grip tape on the treadmill. Find the clip attached to the key (see the drawing above), and slide the clip onto the waistband of your clothing. Follow the steps at the right and on page 9 to operate the console. 8 Insert the key fully into the power switch. Note: Inserting the key will not turn on the display. The display will turn on when the ON/RESET button is pressed or when the walking belt is started. (If you just installed batteries, the display will already be on.) © B Reset the console and start the walking belt. Turn the speed control to the RESET When you are finished exercising, stop the walking belt and remove the key, Step onto the grip tape, stop the walking belt and remove the key from the console. The displays will turn off about six minutes after the key is removed. Note: The display will automatically turn off in order to conserve the batteries any time that the walking belt is Stopped and the ON/RESET button is net pressed for six minutes, position. Note: Each time the walking belt is stopped, the speed control must be turned to the RESET position before the walking belt can be restarted. HOW TO CHANGE THE INCLINE OF THE TREADMILL Next, slowly turn the speed control until the walking belt begins to move at slow speed. Carefully step onto the walking belt and begin exercising. Change the speed of the walking belt as desired by turning the speed control. To stop the walking belt, step onto the foot rails and turn the speed control to the RESET position. k'l Follow your progress with the monitor modes When the power is SCAN CAL$ FAT CAL5 turned on, the console will automatically scan through four modes. A flashing SPEED _ DISTANCE mode indicator will Mode Indicator show which mode is currently displayed. The modes are described below. -12:3-/ • Speed--This per hour. B mode shows your speed, in miles • Time--This mode shows the elapsed time. Note: If you stop exercising for ten seconds or longer, the time mode will pause. • Distance--This mode shows the total number of miles you have walked or run. To vary the intensity of your exercise, the incline of the treadmill can be changed. There are two different incline levels. Before changing the incline, remove the key and unplug the power cord. To change the incline, raise the back of the treadmill and rotate the incline leg until it rests against the treadmill frame. CAUTION: Before using the treadmill, make sure that the frame is resting on the incline leg. Lowest Incline Level Frame _ Highest Frame Level Incline _ ___. _- Leg "-..._..,." • Calories (CALS)--This mode shows the approximate number of calories you have burned. • Fat Calories (FAT CALS)--This mode shows the approximate number of fat calories you have burned. (See BURNING FAT on page 14.) If desired, reset the display by pressing the ON/RESET button. 9 HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Unplug the power cord. Caution: You must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill. 1. Hold the treadmill with your hands in the locations shown at the right. Caution: To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2+ Move your right hand to the position shown and hold the treadmill firmly. Raise the treadmill until the latch pin is aligned with the hole in the handrail. Slide the latch pin into the hole. Make sure that the latch pin is inserted as far as possible into the hole. Lock the pin by pressing the end of the pin into the slot in the storage latch as shown in the inset drawing. To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85 ° Fahrenheit. s'/ I s,ot HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch pin is fully inserted into the hole in the handrail and locked into place as described above. 1. Hold the handrails and place one foot on the base as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface. 3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position. 10 Front Wheels HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, slide the latch pin to the right. Lock the pin in place by pressing the end of the pin into the slot in the storage latch as shown in the inset drawing. Lock Slot--/0_ 2. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight. 11 MAINTENANCE AND TROUBLE-SHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. (See step 1 on page 8.) C. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. 0¢; Tripped Reset PROBLEM: The power turns off during use SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 8.) d. If the treadmill still will not run, please call our Customer Service Department, toll-free. PROBLEM: The displays of the console do not function properly SOLUTION: a. Check the batteries in the console. See assembly step 6 on page 6. Most problems are the result of drained batteries. b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood. Carefully remove the hood. Locate the Reed Switch (46) and the Magnet (49) on the left side of the Pulley (53). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the Screw (26) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. 12 -53 26 _H TopView 46 _ PROBLEM: The walking belt is off-center SOLUTION: a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the right adjustment bolt counterclockwise 1/4 of a turn. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered. b. If the walking belt has shifted to the right, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the right adjustment bolt clockwise 1/4 of a turn. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered. a b 13 CONDITIONING GUIDELINES Burning Fat WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems. The following guidelines will help you to plan your exercise program. Remember--these are general guidelines. For more detailed information about exercise, obtain a book or consult your physician. EXERCISE INTENSITY Whether your goal is to burn fat or strengthen your cardiovascular system, the key to achieving the desired results is to exercise with the proper intensity. The proper intensity level can be found by using your heart, rate as a guide. For effective exercise, your heart rate should be maintained at a levei between 70% and 85% of your maximum heart rate as you exercise. This is known as your training zone. You can Iind your training zone in the table below. Training zones are listed according to age and physical condition. I Training Zone (Beats/Min.) Unconditioned Conditioned 20 i 138-167 133-162 25 136-166 132-160 I 135-164 130-158 35 I 134-162 129-156 132-161 127-155 131-159 125-153 129-156 124-150 127-155 122-149 I 126-153 121-147 65 I 125-151 119-145 70 123-150 118-144 75 122-147 117-142 80 120-146 115-140 85 118-144 114-139 Age I I t [ 36 I 40 I I 45 I To burn fat, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses easily accessible carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the low end of your training zone as you exercise. Aerobic Exercise If your goal is to strengthen your cardiovascular system, your exercise must be "aerobic." Aerobic exercise is activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on the heart to pump blood to the muscles, and on the lungs to oxygenate the blood. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the middle of your training zone. HOW TO MEASURE YOUR HEART RATE To measure your heart rate, place two fingers on your wrist as shown. Stop exercising and take a six-second ' t heartbeat count. Multiply the result by ten to find your heart rate. (A six-second count is used because your heart rate drops quickly when you stop exercising.) If your heart rate is too high, decrease the intensity of your exercise. If your heart rate is too low, increase the intensity of your exercise. WORKOUT GUIDELINES I 50 I 55 60 14 Each workout should include three basic parts: (1) a warm-up, (2) training zone exercise, and (3) a cool-down. Warming Up Warming up prepares the body for exercise by increasing oircu]ation, delivering more oxygen to the muscles and raising the body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up (see SUGGESTED STRETCHES on page 15). Training Zone Exercise to cool down. This will increase the flexibility of your muscles and will help to prevent post-exercise problems. After warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to 60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise--never hold your breath. Cooling Exercise Frequency To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. Down Finish each workout with 5 to 10 minutes of stretching SUGGESTED The key to success is to make exercise a regular and enjoyable part of your everyday life. STRETCHES The correct form for several basic stretches is shown at the right. Move slowly as you stretch--never bounce. 1. Toe Touch Stretch Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and back. 2. Hamstring Stretch Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg. Stretches: Hamstrings, lower back, and groin. 3. Calf/Achilles 3 Stretch With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons, and ankies. 4 4. Quadriceps Stretch With one hand against a wall for balance, reach back and grasp one foot with your ether hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for both legs. Stretches: Quadriceps and hip muscles. 5. Inner Thigh Stretch Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles. 15 EXPLODED DRAWINGmModel NO. WLTL39091 m199A -o 16 30 3O 26 12 i i 15 3O 19" I 41 39 43 44 87 86 13 83 42 35 35, 75 47 77 33 39 38 80 74 59 79 5 91 o.: 62 1 78 51 31 13 30 i 67 i 71 66 69 54 I 65 32 64 PART LIST--Model Key No. Qty. No. WLTL39091 Description R1199A Key No. Qty. 1 2 3 4 5 6 1 1 2 1 4 1 Key/Clip Left Handrail Cage Nut Incline Control Rear Isolator Screw Console Base 49 50 51 52 53 54 1 2 1 1 2 1 7 8 9 10 1 1 1 1 Speed Speed Battery Incline 55 56 57 58 18 4 1 1 11 * 12 13 14 15 16 17 18 19* 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 1 1 10 1 2 7 1 1 1 1 1 4 1 1 1 1 2 1 1 16 1 4 2 2 10 6 2 2 7 1 2 1 1 1 1 4 2 1 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 # # # 2 2 1 2 1 2 2 4 2 1 1 1 2 1 1 1 1 1 4 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 Control Knob Potentiometer Cover Motor Console Assembly Storage Latch 1/2" Screw Upright/Base Handrail Bolt Handrail Washer/Roller Washer Motor Belt Motor Swivel Nut Motor/Pulley/Flywheel/Fan Pulley/Flywheel/Fan Motor Motor Tension Bolt/Incline Bolt Motor Tension Washer Motor Tension Star Washer Motor Swivel Bolt Wire Harness Ground Wire Screw Hood Hood Shield Small Screw Warning Decal Handrail Washer Frame Pivot Bolt Extension Leg Screw Electronics Screw Base Pad Wheel Bolt Wheel Wheel Nut/Base Pivot Nut Controller Extension Leg Circuit Breaker Power Cord Grommet Power Cord Left Upright Spacer Isolator Frame Pivot Washer Choke Description Motor Locknut Belt Guide Belly Pan Releasable Tie REMOVE THIS EXPLODED DRAWING AND PART LIST FROM THE MANUAL. Save this page for future reference. Cable Tie Clamp Motor Belly Pan Screw 8" Wire Tie Right Handrail Incline Wire Harness 3 1/2" Handrail Bolt Extension Leg Assembly Right Upright Spacer Rear Isolator Latch Catch Incline Wheel Bolt Incline Wheel Incline Leg Nut Incline Pivot Bolt Ground Wire Incline Leg Frame Rear Roller Adj. Bolt Rear Roller Endcap Allen Wrench Latch Catch Spacer Left Foot Rail Rear Roller Platform Screw Frame Guide Walking Platform Walking Belt Front Roller Adjustment Bolt Handrail Nut Right Foot Rail Sensor Clip Front Roller/Pulley Reed Switch Magnet Latch Catch Extension Leg Endcap 4" White Wire, Pig Tail 8" Blue Wire, Pig Tail User's Manual * Includes all parts shown in the box # These parts are not illustrated Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of the User's Manual. ORDERING REPLACEMENT PARTS To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give the following information: • The MODEL NUMBER of the product (WLTL11090) • The NAME of the product (WESLO _' CADENCE DX3 treadmirl) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION ING in the center of this manual) of the desired part(s) (see the PART LIST and the EXPLODED DRAW- If possible, place the treadmill near your telephone for easy reference when calling. WESLO is a registered trademark of ICON Health & Fitness, Inc. LIMITED WARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center, to products used for commercial or rental purposes, or to products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON. ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not arrow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 Part No. 157691 R0999B Printed in USA © 1999 ICON Health & Fitness, Inc.