User manual | LIQUID CRYSTAL DISPLAY MODULE MODEL: NMTG-S12232CFYHSGY-10 Customer’s No.:

Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
1 / 21
LIQUID CRYSTAL DISPLAY MODULE
MODEL: NMTG-S12232CFYHSGY-10
Customer’s No.:
Acceptance
Microtips Technology Inc.
12F. No.31 Lane 169, Kang Ning St.,
His-Chih, Taipei Hsien, Taiwan, R.O.C.
FAX: 886-2-26958625
Approved and Checked by
Approved by
Checked by
Made by
微 端
微 端
2006/09/06
2006/09/06
2006/09/06
2006/09/06
張秀美
連俊傑
蔡宜夢
陳雅靖
微 端
微 端
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
2 / 21
Revise Records
Rev.
Date
Contents
Written
Approved
A
2006/09/06
Initial Edition
Sherry Chen
Danny Lian
Special Notes
Note1.
Note2.
Note3.
Note4.
Note5.
The LCD module is compliant with RoHS.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
3 / 21
Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
General Specifications .........................................................................................................................4
Electrical Specifications ........................................................................................................................5
2.1
Absolute Maximum Ratings.................................................................................................5
2.2
DC Characteristics................................................................................................................5
2.3
AC Characteristics ................................................................................................................6
2.4
Power Supply ON/OFF Sequence......................................................................................8
2.5
Lighting Specifications..........................................................................................................9
Optical Specifications ........................................................................................................................10
3.1
LCD Driving Voltage Recommended ...............................................................................10
3.2
Optical Characteristics .......................................................................................................10
3.3
Definition of Viewing Angle and Optimum Viewing Area .............................................11
3.4
Definition of Viewing Angle θf and θb ...............................................................................11
3.5
Definition of Contrast C.....................................................................................................11
I/O Terminal........................................................................................................................................12
4.1
Pin Assignment ...................................................................................................................12
4.2
Example of Power Supply ..................................................................................................12
4.3
Block Diagram ....................................................................................................................13
Reliability Test .....................................................................................................................................14
5.1
Test Item..............................................................................................................................14
5.2
Judgment Standard.............................................................................................................15
Appearance Standards .......................................................................................................................16
6.1
Inspection Conditions ........................................................................................................16
6.2
Definition of Applicable Zones .........................................................................................16
6.3
Standards.............................................................................................................................17
Handling and Precautions..................................................................................................................19
Warranty:.............................................................................................................................................20
Dimensional Outlines.........................................................................................................................20
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
4 / 21
The Microtips Customized LCD module, model: NMTG-S12232CFYHSGY-10 is compliant with
RoHS
1. General Specifications
Operating Temperature
:
Min. -20°C ～ Max. 70°C
Storage Temperature
:
Min. -30°C ～ Max. 80°C
Dot Pixels
:
122 (W) x 32 (H) dots
Dot Size
:
0.345 (W) x 0.345 (H) mm
Dot Pitch
:
0.375 (W) x 0.375 (H) mm
Viewing Area
:
52.0 (W) x 15.0 (H) mm
Outline Dimensions
:
59.0 (W) x 29.3 (H) x 5.5 max. (D) mm
Weight
:
N/A
LCD Type
:
STN/ Positive Yellow-Green mode/ Transflective
Viewing Direction
:
6:00
Backlight
:
Edge Type LED B/L (Yellow-Green)
LSI
:
SBN1661G-M18-D
Drawings
:
As attached drawings
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
5 / 21
2. Electrical Specifications
2.1 Absolute Maximum Ratings
VSS = 0V
Parameter
Symbol
Conditions
Min.
Max.
Units
Supply Voltage (Logic)
VDD - VSS
--
- 0.3
8.0
V
Supply Voltage (LCD Drive)
VDD - VEE
--
-0.30
16.5
V
VI
--
- 0.3
VDD + 0.3
V
Input Voltage
2.2 DC Characteristics
Ta = 25°C, VSS = 0V
Parameter
Supply
Voltage
(Logic)
Recommended
Symbol
Conditions
VDD - VSS
--
Allowable
Supply Voltage (LCD Drive)
High Level (Input Voltage)
Low Level (Input Voltage)
VDD - VO
Min.
Typ.
Max.
Units
4.5
5.0
5.5
V
2.7
--
7.0
V
Shown in 3.1
VIHT
Note 1
VIHC
VILT
Note 1
VILC
V
2.0
--
VDD
V
0.8VDD
--
VDD
V
0
--
0.8
V
0
--
0.2VDD
V
High Level (Output Voltage)
VOH
IOH = -3.0mA
Note 2
2.7
--
--
V
Low Level(Output Voltage)
VOL
IOH = 3.0mA
Note 2
--
--
0.4
V
IDD
VDD - VSS
--
0.6
1.1
mA
IEE
VDD - VEE
--
1.8
3.3
mA
Supply Current
Note 1 : Applied to A0, E1, E2, DB0~DB7, R/W.
Note 2 : Applied to DB0~DB7.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
6 / 21
2.3 AC Characteristics
2.3.1 MPU Bus Read/Write I (80-family MPU)
A0, CS
t AW8
t CC
t AH8
tr
t CYC8
WR, RD
tf
t DH8
t DS8
DB0 ～DB7
(WRITE)
t ACC8
t OH8
DB0 ～DB7
(READ)
Ta= -20~70°C, VDD=5.0V±10％, unless state otherwise
Parameter
Symbol
Condition
Address hold time
tAH8
Address setup time
System cycle time
Rating
Unit
Min.
Max.
--
10
--
ns
tAW8
--
20
--
ns
tCYC8
--
1000
--
ns
Control pulse-width
tCC
--
200
--
ns
Data setup time
tDS8
--
80
--
ns
Data hold time
tDH8
--
10
--
ns
RD access time
tACC8
--
90
ns
Output disable time
tCH8
10
60
ns
Rise and fall time
tr, tf
--
15
ns
CL=100Pf
--
Signal
A0, CS
WR, RD
D0 to D7
--
Ta= -20~70°C, VDD=3.0V±10％, unless state otherwise
Parameter
Symbol
Condition
Address hold time
tAH8
Address setup time
System cycle time
Rating
Unit
Min.
Max.
-
20
-
ns
tAW8
-
40
-
ns
tCYC8
-
2000
-
ns
Control pulse-width
tCC
-
400
-
ns
Data setup time
tDS8
-
160
-
ns
Data hold time
tDH8
-
20
-
ns
RD access time
tACC8
-
180
ns
Output disable time
tCH8
20
120
ns
Rise and fall time
tr, tf
-
15
ns
CL=100pF
-
Signal
A0, CS
WR, RD
D0 to D7
-
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
7 / 21
2.3.2 MPU Bus Read/Write II (68-family MPU)
tCYC6
tEW
E
tEW
tr
tf
R/W
tAH6
A0, CS
tDH6
DB0 ～ DB7
(WRITE)
tACC6
tOH6
DB0 ～ DB7
(READ)
Ta= -20~70°C, VDD=5.0V±10％, unless state otherwise
Parameter
System cycle time
Address setup time
Address hold time
Data setup time
Data hold time
Output disable time
Access time
Read
Enable
pulse-width
Write
Rise and fall time
Parameter
System cycle time
Address setup time
Address hold time
Data setup time
Data hold time
Output disable time
Access time
Read
Enable
pulse-width
Write
Rise and fall time
Symbol
tCYC6
tAW6
tAH6
tDS6
tDH6
tOH6
tACC6
tEW
tr, tf
Symbol
tCYC6
tAW6
tAH6
tDS6
tDH6
tOH6
tACC6
Rating
Unit
Signal
Min.
Max.
1000
ns
A0, CS, R/W
20
ns
10
ns
80
ns
10
ns
D0 to D7
10
60
ns
CL=100pF
90
ns
100
ns
E
80
ns
15
Ns
Ta= -20~70°C, VDD=3.0V±10％, unless state otherwise
Rating
Condition
Unit
Signal
Min.
Max.
2000
ns
A0, CS, R/W
40
ns
Condition
CL=100pF
tEW
tr, tf
-
20
160
20
20
200
160
-
120
180
15
ns
ns
ns
ns
ns
ns
ns
Ns
D0 to D7
E
-
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
8 / 21
2.4 Power Supply ON/OFF Sequence
2.4.1 ON Sequence
SIGNAL
LEVEL
VDD
VSS
VDD
0≤ t
SIGNAL
VDD
VSS
0≤ t
VDD
VSS
VEE
VEE
2.4.2 OFF Sequence
LEVEL
SIGNAL
VDD
VSS
VDD
0≤ t
VDD
VSS
0≤ t
SIGNAL
VDD
VSS
VEE
VEE
Please maintain the above sequence when turning on and off the power supply of the module. If VEE
is supplied to the module while internal alternate signal for LCD driving (M) is unstable or RESET is
active, DC component will be supplied to the LCD panel. This may cause damage to the LCD
module.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
9 / 21
2.5 Lighting Specifications
2.5.1 Absolute Maximum Ratings
Ta = 25°C
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
Forward Current
IF
--.
--
--
40
mA
Reverse Voltage
VR
--
--
--
--
V
LED Power Dissipation
PD
--
--
--
--
mW
2.5.2 Operating Characteristics
Ta = 25°C
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Units
Forward Voltage
VF
IF = 40mA
--
4.2
4.8
V
Luminance of Backlight Surface*
L
IF = 40mA
21
30
42
cd/m2
Luminance Tolerance*
-IF = 40mA
*Measured from the surface of backlight.
*Luminance Tolerance = (Max. - Min./Max.) x 100%
75
--
--
%
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
10 / 21
3. Optical Specifications
3.1 LCD Driving Voltage Recommended
Parameter
LCD Driving Voltage Note 1
Note 1 :
Symbol
VDD-VO
Conditions
Min.
Typ.
Max.
Units
Ta = -20 °C
6.58
6.88
6.18
V
Ta = 25 °C
6.30
6.60
6.90
V
Ta = 70 °C
6.02
6.32
6.62
V
Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of minimum and
maximum shows tolerance of the operating voltage. The specified contrast ratio and response time
are not guaranteed over the entire range.
3.2 Optical Characteristics
Ta=25 °C, 1/32 Duty, 1/6 Bias, VDD = 5V (Note 4), θ = 0°, φ = 0°
Parameter
Contrast Ratio Note 1
Viewing Angle (Shown in 3.3)
Response
Time
Note 1 :
Note 2 :
Note 3 :
Note 4 :
Rise Note 2
Symbol
Conditions
Min.
Typ.
Max.
Units
C
θ = 0°, φ = 0°
2.0
6.0
--
--
Front-Back
θf - θb, φ = 0°
+83
to
-30
deg.
Left-Right
θl - θr, φ = 0°
+35
to
-35
deg.
TON
--
--
85
250
msec
--210
230
msec
Decay Note 3
TOFF
Contrast ratio is defined as follows.
CR = LOFF / LON
LON : Luminance of the ON segments, LOFF : Luminance of the OFF segments
The time that the luminance level reaches 90% of the saturation level from 0% when ON signal is
applied.
The time that the luminance level reaches 10% of the saturation level from 100% when OFF
signal is applied.
Definition of Driving Voltage VD. Assuming that the typical driving waveforms shown below are
applied to the LCD Panel at /A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving
voltage VD is defined s follows: VD = (Vth1+Vth2) / 2
Vth1 :
The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the ON signal is applied to.
Vth2 :
The voltage VO-P that should provide 50% of the saturation level in the luminance at
the segment which the OFF signal is applied to.
Vo -p
1 / fF
(B-2) x Vo-p / B
1 / (fF x A)
Selected state
(ON SIGNAL)
Unselected state
(OFF SIGNAL)
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
11 / 21
3.3 Definition of Viewing Angle and Optimum Viewing Area
θl
θb
Di
re
cti
on
:6
H
( φ = 90 ο)
θf
( φ = 180 ο)
Vi
ew
θr
( φ = 0 ο)
( φ = 270 ο)
( LCD panel )
3.4 Definition of Viewing Angle θf and θb
Cmax.
2.0
θf
θb
Viewing angles θ ( φ fixed)
Optimum viewing angle with the naked
eye and viewing angle θ at Cmax.
Above are not always the same.
3.5 Definition of Contrast C, C= Brightness of selected dot (B1 )/ Brightness of unselected dot (B2)
(%)
Dark
B1
unselected portion brightness
curve (bias voltage applied)
Brightness
selected portion
brightness curve
B2
Bright
Operation Voltage (V)
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
12 / 21
4. I/O Terminal
4.1 Pin Assignment
No.
Symbol
Level
Function
1
/VLED
H/L
2
VSS
--
GND
3
VDD
--
Logic supply voltage
4
Vo
--
LCD driver supply voltage
5
A0
H/L
Display Data/Display commands switching input.
A0=0: DB0~DB7 are command input and status output.
A0=1: DB0~DB7 are Display Data input/output.
6
E1
H/L
Enable signal input for the left half of the screen. Active LOW
7
E2
H/L
Enable signal input for the right half of the screen. Active LOW
8
DB0
I/O
9
DB1
I/O
10
DB2
I/O
11
DB3
I/O
12
DB4
I/O
13
DB5
I/O
14
DB6
I/O
15
DB7
I/O
16
R/W
H/L
Cathode of LED backlight, which is common Anode with logic circuit.
3-state I/O Data Bus.
High for READ, Low for WRITE.
4.2 Example of Power Supply
It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage
and its temperature dependence.
VDD
VDD (+Voltage)
Module
R1
Vo
VR
R2
VEE (-Voltage)
VSS
VSS (0V)
R1+R2+VR=10 ～ 20K Ω
Tr=2SA1202 or equivalent
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
13 / 21
4.3 Block Diagram
LCDP
16
16
122 x 32 dots
Common
61
AX6120D0A
or equivalent
Segment
61
AX6120D0A
or equivalent
E1
E2
A0
R/W
DB0 ～ DB7
VDD
VSS
Bias Circuit
Vo
VDD (LEDA)
LED Backlight
VLED(LEDK)
To LSI
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
14 / 21
5. Reliability Test
5.1 Test Item
No change on display and in operation under the following test condition.
No.
Test Item
Description
Condition
1.
High Temperature
(Operation)
Durability test under long time high
temperature with electrical stress (voltage,
current)
70°C ± 2°C 96hrs
2.
High Temperature
(Storage)
Durability test under long time high
temperature storage
80°C ± 2°C 96hrs
4
3.
Low Temperature
(Operation)
Durability test under long time low
temperature with electrical stress (voltage,
current)
-20°C ± 2°C, 96hrs
3
4.
Low Temperature
(Storage)
Durability test under long time low
temperature storage
-30°C ± 2°C, 96hrs
3, 4
5.
Damp Proof Test
Durability test under long time high
temperature and high humidity
40°C± 2°C, 90～95%
RH 96hrs
3,4
Vibration Test
Total fixed amplitude: 1.5mm
Vibration frequency: 10～55Hz
One cycle 60 seconds to 3 directions of X,
Y, Z for each 15 minutes
--
5
6.
Note
To be measured after dropping from 60cm high on the concrete
surface in packing state.
F
Dropping method corner dropping
A corner: once
7.
Drop Test
E
G
D
C
A
B
Edge dropping
B, C, D edge: once
Face dropping
60cm
E, F, G face: once
Concrete Surface
Note 1: Unless otherwise specified, tests will be conducted under the following condition,
Temperature
: 25°C ± 2°C
Humidity
: 65% ± 5%
Note 2: Unless otherwise specified, tests will be not conducted under functioning state.
Note 3: No dew condensation to be observed.
Note 4: The function test shall be conducted after 4 hours storage at the normal temperature and humidity
after removed from the test chamber.
Note 5: Vibration test will be conducted to the product itself without putting it in a container.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
15 / 21
5.2 Judgment Standard
Test Item
Failure Mode
Judgment Standard
1
2
3
4
5
Orientation
*
*
*
*
*
No remarkable degradation of appearance
under bias/ non-bias condition
Current Value (IAC)
*
*
*
*
*
No remarkable increase
Contrast
*
*
*
*
No remarkable poor contrast
Domain
*
*
*
*
*
Less than 20% of all dots have reverse tilt of
more than on third of one dot area.
Bubble (Inside Cell)
*
*
*
*
*
*
As per “Appearance Standard” (Note. Including one which disappear after 25°C 2H)
Polarizer
*
*
*
As per “Appearance Standard” no remarkable
appearance change
Glass Damage
6
7
*
As per “Appearance Standard”
Note.1. * is strong linkage between Failure Mode and Test Item.
2. Number of Test Item should be referred to former page.
3. Judgment and Standard value should be fixed by other inspection standard and criteria samples.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
16 / 21
6. Appearance Standards
6.1 Inspection Conditions
The LCD shall be inspected under 40W white fluorescent light. The distance between the eyes and the
sample shall be more than 30cm. All directions for inspecting the sample should be within 45° against
perpendicular line.
45
O
6.2 Definition of Applicable Zones
A Zone
Bezel Frame
B Zone
C Zone
A Zone : Active display area
B Zone : Area from outside of "A Zone" to validity viewing area
C Zone : Rest parts
A Zone + B Zone = Validity viewing area
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
17 / 21
6.3 Standards
No.
Parameter
Criteria
(1) Round Shape
Acceptable Number
Zone
Dimension (mm)
1.
Black and White
Spots, Foreign
Substances
A
B
C
D
≤ 0.1
*
*
*
0.1
< D
≤ 0.2
3
5
*
0.2
< D
≤ 0.25
2
3
*
0.25
< D
≤ 0.3
0
1
*
0.3
< D
0
0
*
D = (Long + Short)/2 *: Disregard
(2) Line Shape
Zone
Zone
X (mm)
--
Y (mm)
A
B
C
≥ W
0.05 ≥ W
0.1 ≥ W
*
*
*
3
3
*
3
3
*
0.03
≥
1.0 ≥
2.0
L
L
--
Acceptable Number
0.1
< W
In the same way (1)
X : Length Y: Width *: Disregard
Total defects shall not exceed 5.
Acceptable Number
Zone
Dimension (mm)
2.
Air Bubbles
(between glass
& polarizer)
B
C
D
≤ 0.3
*
*
*
0.3
<
D
≤ 0.4
3
*
*
0.4
<
D
≤ 0.6
2
3
*
0.6
<
D
0
0
*
*: Disregard
Total defects shall not exceed 3.
To be continued……
A
Messrs.
Product Specification
No.
Model: NMTG-S12232CFYHSGY-10
Parameter
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
18 / 21
Criteria
(1) Dot Shape (with Dent)
0.15 ≥
As per the sketch of left
hand.
(2) Dot Shape (with Projection)
Should not be connected
to next dot.
(3) Pin Hole
X
3.
The Shape of Dot
Y
(X+Y)/2 ≤ 0.2mm (Less
than 0.1mm is no counted.)
(4) Deformation
(X+Y)/2 ≤ 0.2mm
Y
X
Total acceptable number: 1/dot, 5/cell
(Defect number of (4): 1pc.)
4.
Polarizer Scratches
Not to be conspicuous defects.
5.
Polarizer Dirts
I f the stains are removed easily from LCDP surface, the
module is not defective.
6.
Complex Foreign
Substance Defects
Black spots, line shaped foreign substance or air bubbles
between glass & polarizer should be 5pcs maximum in total.
7.
Distance between
different Foreign
Substance defects
D ≤ 0.2 : 20mm or more
0.2 < D : 40mm or more
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
19 / 21
7. Handling and Precautions
The Following precautions will guide you in handling our product correctly.
1
Liquid crystal display devices
1.1
1.2
2
Care of the liquid crystal display module against static electricity discharge.
2.1
2.2
2.3
3
The liquid crystal display device panel used in the liquid crystal display module is made of
plate glass. Avoid any strong mechanical shock. Should the glass break handle it with care.
The polarizer adhering to the surface of the LCD is made of a soft material. Guard against
scratching it.
When working with the module, be sure to ground your body and any electrical
equipment you may be using. We strongly recommend the use of anti static mats ( made
of rubber ), to protect work tables against the hazards of electrical shock.
Avoid the use of work clothing made of synthetic fibers. We recommend cotton clothing
or other conductivity-treated fibers.
Slowly and carefully remove the protective film from the LCD module, since this operation
can generate static electricity.
When the LCD module alone must be stored for long periods of time:
3.1
3.2
3.3
Protect the modules from high temperature and humidity.
Keep the modules out of direct sunlight or direct exposure to ultra-violet rays.
Protect the modules from excessive external forces.
4
Use the module with a power supply that is equipped with an over current protector circuit,
since the module is not provided with this protective feature.
5
Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands or
clothing come in contact with LCD fluid, wash immediately with soap.
6
Conductivity is not guaranteed for models that use metal holders where solder connections
between the metal holder and the PCB are not used. Please contact us to discuss appropriate
ways to assure conductivity.
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
20 / 21
8. Warranty:
This product has been manufactured to your company’s specifications as a part for use in your company’s
general electronic products. It is guaranteed to perform according to delivery specifications. For any other
use apart from general electronic equipment, we cannot take responsibility if the product is used in medical
devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other
applications in which there is a direct risk to human life and where extremely high levels of reliability are
required. If the product is to be used in any of the above applications, we will need to enter into a separate
product liability agreement.
1
We cannot accept responsibility for any defect, which may arise from additional manufacturing of the
product (including disassembly and reassembly), after product delivery.
2
We cannot accept responsibility for any defect, which may arise after the application of strong external
force to the product.
3
We cannot accept responsibility for any defect, which may arise due to the application of static
electricity after the product has passed your company’s acceptance inspection procedures.
4
We cannot accept responsibility for industrial property, which may arise through the use of your product,
with exception to those issues relating directly to the structure or method of manufacturing of our
product. Microtips-origin longer than one year from Microtips production.
9. Dimensional Outlines
z
See the next page……..
Messrs.
Product Specification
Model: NMTG-S12232CFYHSGY-10
Rev. No.
Issued Date.
Page.
A
Sep.06, 06
21 / 21
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Microtips Technology:
NMTG-S12232CFYHSGY-10

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project