Seagate | MOMENTUS ST160LT007 | Product manual | Seagate MOMENTUS ST160LT007 Product manual

Product Manual
Momentus Thin
®
7200-RPM
ST model # - Part #
ST model # - Part #
Standard models
SED model
ST320LT007 - 9ZV142
ST320LT014 - 9YK142
ST250LT007 - 9ZV14C
ST250LT014 - 9YK14C
ST160LT007 - 9ZV14D
ST160LT014 - 9YK14D
Free-Fall Sensor models
SED (FIPS 140-2) models
ST320LT011 - 9ZVG42
ST320LT009 - 9WC142
ST250LT011 - 9ZVG4C
ST250LT009 - 9WC14C
ST160LT011 - 9ZVG4D
ST160LT009 - 9WC14D
Gen-2
100625253
Rev. C
January 2011
Revision history
Revision
Rev. A
Rev. B
Rev. C
Date
06/02/10
06/24/10
01/04/11
Sheets affected or comments
Initial release.
fc, 2, 4, 6, 21 & 26-28.
5, 8, 15 & 20.
© 2011 Seagate Technology LLC. All rights reserved.
Publication number: 100625253, Rev. C January 2011
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology
LLC in the United States and/or other countries. Momentus and SeaTools are either trademarks or
registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United
States and/or other countries. The FIPS logo is a certification mark of NIST, which does not imply
product endorsement by NIST, the U.S., or Canadian governments. All other trademarks or registered trademarks are the property of their respective owners.
No part of this publication may be reproduced in any form without written permission of Seagate
Technology LLC. Call 877-PUB-TEK1 (877-782-8351) to request permission.
One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes.
Your computer's operating system may use a different standard of measurement and report a lower
capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus
will not be available for data storage. Seagate reserves the right to change, without notice, product
offerings or specifications.
Contents
1.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1
About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.0
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1
Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2.1
LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.4
Physical organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.5
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.6
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.7
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.8
Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.9
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.9.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.9.2
Deferred spinup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.9.3
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.9.4
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.9.5
Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.10
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.10.1
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.10.2
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.10.3
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.10.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.10.5
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.10.6
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.11
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.12
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.13
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.14
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.14.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.14.2
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.14.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.15
Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.15.1
European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 17
3.15.2
China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 17
3.16
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.0
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.0
About FIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.0
Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.2
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.3
S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Momentus Thin Product Manual, Rev. C Gen-2
18
18
18
19
19
24
24
24
26
28
32
33
i
ii
Momentus Thin Product Manual, Rev. C Gen-2
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting dimensions (for FIPS 140-2 models) — top, side and end view . . . . . . . . . . . . . . .
Mounting dimensions (for standard models) — top, side and end view . . . . . . . . . . . . . . . . .
Example of FIPS tamper evidence labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Momentus Thin Product Manual, Rev. C Gen-2
10
18
19
20
21
22
iii
1.0
Seagate Technology support services
SEAGATE ONLINE SUPPORT and SERVICES
For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/
Available services include:
Presales & Technical support
Global Support Services telephone numbers & business hours
Authorized Service Centers
For information regarding Warranty Support, visit
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
For information regarding Data Recovery Services, visit http://www.i365.com
For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system
For Seagate reseller portal, visit http://spp.seagate.com
Momentus Thin Product Manual, Rev. C Gen-2
1
2.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate
Momentus® Thin model drives:
ST model #
Part #
Standard models
ST model #
Part #
ST model #
Part #
Standard SED models
SED (FIPS 140-2) models
ST model #
Part #
Free-Fall Sensor models
ST320LT007
9ZV142
ST320LT014
9YK142
ST320LT009
9WC142
ST320LT011
9ZVG42
ST250LT007
9ZV14C
ST250LT014
9YK14C
ST250LT009
9WC14C
ST250LT011
9ZVG4C
ST160LT007
9ZV14D
ST160LT014
9YK14D
ST160LT009
9WC14D
ST160LT011
9ZVG4D
Note.
Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption
(FDE) models before a differentiation between drive-based encryption and other forms of encryption was necessary.
Note.
The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for
“Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see
www.trustedcomputinggroup.org).
For more information on FIPS 140-2 Level 2 certification See Section 5.0 on page 22 .
These drives provide the following key features:
• 7200-RPM spindle speed.
• 16-MB buffer.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• High instantaneous (burst) data-transfer rates (up to 3Gb/s).
• Perpendicular recording technology.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Native Command Queuing (NCQ) with command ordering.
• Full-track multiple-sector transfer capability without local processor intervention.
• 1000 Gs nonoperating shock and 350 Gs of operating shock.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense and Diagnostic Defense, offers the
industry’s most comprehensive protection for disk drives.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
2
Momentus Thin Product Manual, Rev. C Gen-2
Momentus Thin Self-Encrypting Drive models have the following additional features:
•
•
•
•
•
•
Automatic data encryption/decryption
Controlled access
Random number generator
Drive locking
16 independent data bands
Cryptographic erase of user data for a drive that will be repurposed or scrapped
• Authenticated firmware download
There is no significant performance difference between Self-Encrypting Drive and standard (non-Self-Encrypting Drive) models.
2.1
About the Serial ATA interface
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary
advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set
any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current
system and expect all of your existing applications to work as normal.
The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0
(master) devices.
Note.
The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA
environment.
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide
backward compatibility with existing host systems and software. The Command and Control Block registers,
PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized
AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.
Momentus Thin Product Manual, Rev. C Gen-2
3
3.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate all
models.
3.1
Specification summary table
The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual
Table 1:
Drive specifications
Drive specification
ST320LT007 - 9ZV142
ST320LT009 - 9WC142
ST320LT011 - 9ZVG42
ST320LT014 - 9YK142
ST250LT007 - 9ZV14C
ST250LT009 - 9WC14C
ST250LT011 - 9ZVG4C
ST250LT014 - 9YK14C
ST160LT007 - 9ZV14D
ST160LT009 - 9WC14D
ST160LT011 - 9ZVG4D
ST160LT014 - 9YK14D
Formatted capacity (GB)*
320
250
160
Guaranteed logical blocks (LBA)
625,142,448
488,397,168
312,581,808
Bytes per physical sector
4096
Physical read/write heads
2
Disks
1
Cache (MB)
16
Recording density in BPI (bits/in avg)
1397k
Track density TPI (tracks/in avg)
315k
Areal density (Gb/in2 avg)
425
1
Spindle speed (RPM)
7200
Average latency (ms)
4.17
Internal transfer rate (Mb/s max)
1247
I/O data transfer rate (Gb/s max)
3.0
ATA data-transfer modes supported
SATA 1.0, Serial ATA Revision 2.6
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Height (max)
7.0 mm (0.276 in)
Width (max)
70.10 mm (2.76 in)
Length (max)
100.55 mm (3.959 in)
Weight (max)
<92.0 g (<0.203 lb)
Power-on to ready (sec typical)
3.5
Standby to ready (sec typical)
3.0
Track-to-track seek time, read (ms typical)
1.5
Average seek, read (ms typical)
11
Startup current, +5V (max)
1.0A
4
Momentus Thin Product Manual, Rev. C Gen-2
Table 1:
Drive specifications
Drive specification
ST320LT007 - 9ZV142
ST320LT009 - 9WC142
ST320LT011 - 9ZVG42
ST320LT014 - 9YK142
Read/write power (typical)
Read: 1.6W; Write: 1.9W
Idle mode, low power (typical)
0.66W
ST250LT007 - 9ZV14C
ST250LT009 - 9WC14C
ST250LT011 - 9ZVG4C
ST250LT014 - 9YK14C
Standby/Sleep mode (typical)
0.15W ***
Voltage tolerance (including noise)
+5V ± 10%
Ambient temperature
0° to 60°C (operating), –40° to 70°C (nonoperating)
Temperature gradient
(°C per hour max)
20°C (operating)
35°C (nonoperating)
Relative humidity
5% to 95% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature
(°C max)
37.7 (operating)
40 (nonoperating)
Altitude, operating
–304.8 m to 3,048 m (–1000 ft. to 10,000+ ft.)
Altitude, nonoperating
(meters below mean sea level, max)
–304.8 m to 12,192 m (–1000 ft. to 40,000+ ft.)
Shock, operating (Gs max at 2ms)
350
Shock, nonoperating (Gs max at 2ms)
800
Shock, nonoperating (Gs max at 1ms)
1000
Shock, nonoperating (Gs max at 0.5ms)
600
Vibration, operating (Swept Sine)
1.0 Gs (0 to peak, 5–500 Hz)
Vibration, nonoperating
5.0 Gs (0 to peak, 5–500 Hz)
ST160LT007 - 9ZV14D
ST160LT009 - 9WC14D
ST160LT011 - 9ZVG4D
ST160LT014 - 9YK14D
Drive acoustics, sound power (bels)
Idle**
2.3 (typical)
2.5 (max)
Seek
2.5 (typical)
2.7 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.50%
Load/Unload (U/UL) cycles
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
To determine the warranty for a specific drive, use a web browser to access the following
web page: http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
You will be asked to provide the drive serial number, model number (or part number)
and country of purchase. After submitting this information, the system will display the
warranty information for your drive.
Supports Hotplug operation per Serial ATA
Revision 2.6 specification
Yes (requires COMRESET from host after a hotplug event)
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby
modes will not contribute to battery power consumption.
Momentus Thin Product Manual, Rev. C Gen-2
5
3.2
Formatted capacity
Formatted capacity*
Guaranteed logical blocks (LBA) - 512 emulation
ST320LT007 - 9ZV142
ST320LT009 - 9WC142
ST320LT011 - 9ZVG42
ST320LT014 - 9YK142
625,142,448
ST250LT007 - 9ZV14C
ST250LT009 - 9WC14C
ST250LT011 - 9ZVG4C
ST250LT014 - 9YK14C
488,397,168
ST160LT007 - 9ZV14D
ST160LT009 - 9WC14D
ST160LT011 - 9ZVG4D
ST160LT014 - 9YK14D
312,581,808
Bytes per physical sector
4096
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
3.2.1
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed logical blocks (LBA) as defined above.
See Section 6.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48bit addressing support of drives with capacities over 137GB.
3.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed logical blocks (LBA) as defined above.
3.4
Physical organization
Models
Read/write heads
Number of disks
320GB models
2
250GB models
160GB models
6
1
1
Momentus Thin Product Manual, Rev. C Gen-2
3.5
Recording and interface technology
4K sector models
Interface
Serial ATA (SATA)
Recording method
Perpendicular
Recording density BPI (bits/in avg)
1397k
Track density TPI (tracks/in avg)
315k
Areal density (Gb/in2 avg)
425
Spindle speed (RPM) (± 0.2%)
7200
Maximum Internal transfer rate (Mb/s)
1247
I/O data-transfer rate (Gb/s max)
3.0
Interleave
1:1
Cache buffer
3.6
16 MB (16,384 KB)
Physical characteristics
Drive specification
Height
(mm)
(in)
6.8 +/-0.2
0.268 +/-0.0079
Width
(mm)
(in)
69.85 +/-0.25
2.75 +/-0.0098
Length
(mm)
(in)
100.35 +0.20/-0.25
3.951 +0.008/-0.010
Weight (max)
92.0 g
0.203 lb
All models
3.7
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between
random tracks, less overhead.
Table 2:
Typical seek times
Typical seek times (ms)
Read
Track-to-track
1.5
Average
11
Average latency
4.17
Note.
These drives are designed to consistently meet the seek times represented in this manual. Physical
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted
values. However, due to the manner in which these drives are formatted, benchmark tests that
include command overhead or measure logical seeks may produce results that vary from these
specifications.
Momentus Thin Product Manual, Rev. C Gen-2
7
3.8
Start/stop times
Time to ready
Typical
Max @ 25°C
Power-on to Ready (sec)
3.5
4.0
Standby to Ready (sec)
3.0
3.0
3.9
Power specifications
The drive receives DC power (+5V) through a native SATA power connector.
3.9.1
Power consumption
Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on
an average of drives tested, under nominal conditions, at 25°C ambient temperature. These power measurements are done with Interface Power Management modes like HIPM and DIPM enabled.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on
three random seek operations every 100ms. This mode is not typical.
• Read/write power and current
Read/write power is measured with the heads on track, based on three 63 sector read or write operations
every 100ms.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down model
Table 3:
DC power
Power dissipation
+5V input average (25° C)
Spinup (max)
1.00A
Seek
1.6W
Read
1.6W
Write
1.9W
Idle, performance*
1.3W
Idle, active*
0.90W
Idle, low power mode*
0.66W
Standby**
0.15W
Sleep
0.15W
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
8
Momentus Thin Product Manual, Rev. C Gen-2
power to operational levels.
**Standby power is measured at steady state (after 200ms from transition)
Momentus Thin Product Manual, Rev. C Gen-2
9
3.9.1.1
Typical current profile
Figure 1. Typical +5V only startup and operation current profile
3.9.2
Deferred spinup
Momentus Thin drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives.
3.9.3
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +5 volt line.
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note.
Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write
current.
3.9.4
Voltage tolerance
Voltage tolerance (including noise):
5V ± 10%
10
Momentus Thin Product Manual, Rev. C Gen-2
3.9.5
Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems,
you can control power management through the system setup program. The drive features the following
power-management modes:
Table 4:
Power management modes
Power modes
Heads
Spindle
Buffer
Active (operating)
Tracking
Rotating
Full power
Idle, performance
Tracking
Rotating
Self refresh—low power
Idle, active
Floating
Rotating
Self refresh—low power
Idle, low power
Parked
Rotating
Self refresh—low power
Standby
Parked
Stopped
Self refresh—low power
Sleep
Parked
Stopped
Self refresh—low power
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Idle mode
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk
access is necessary.
• Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the
standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a
specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby
mode, the drive buffer is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest.
The drive accepts all commands and returns to Active mode any time disk access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer
is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep
mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep
mode and enters Standby mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any
drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the
drive accepts all commands and returns to Active mode when disk access is necessary.
Momentus Thin Product Manual, Rev. C Gen-2
11
3.10
Environmental specifications
3.10.1
Ambient temperature
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Operating:
0° to 60°C (32° to 140°F)
Nonoperating:
–40° to 70°C (–40° to 158°F)
3.10.2
Temperature gradient
Operating
20°C per hour (68°F per hour max), without condensation
Nonoperating
35°C per hour (95°F per hour max), without condensation
3.10.3
Humidity
3.10.3.1
Relative humidity
Operating
5% to 95% noncondensing (30% per hour max)
Nonoperating
5% to 95% noncondensing (30% per hour max)
3.10.3.2
Wet bulb temperature
Operating
37.7°C (99.86°F max)
Nonoperating
40°C (104°F max)
3.10.4
Altitude
Operating
–304.8 m to 3,048 m (–1000 ft to 10,000+ ft)
Nonoperating
–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)
12
Momentus Thin Product Manual, Rev. C Gen-2
3.10.5
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
3.10.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 350 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than
two times per second.
3.10.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse
of 2ms duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock
pulse of 1ms duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 600 Gs based on a nonrepetitive half-sine shock pulse
of 0.5ms duration.
3.10.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
3.10.6.1
Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below.
5–500 Hz
3.10.6.2
1.0 Gs (0 to peak). Max displacement may apply below 10Hz.
Nonoperating vibration
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage
or degradation in performance when subsequently put into operation are specified below.
5–500 Hz:
5.0 Gs (0 to peak). Max displacement may apply below 22Hz.
Momentus Thin Product Manual, Rev. C Gen-2
13
3.11
Acoustics
Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is
conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted
sound power levels for steady state, idle, and active seek modes of operation.
Table 5:
Drive A-weighted Sound Power Levels (SWL, BA)
Idle*
Performance seek
2.3 bels (typ)
2.5 bels (max)
2.5 bels (typ)
2.7 bels (max)
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
Test for Prominent Discrete Tones (PDTs)
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to
discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone
ratios according to Annex D of the ECMA-74 standards.
*Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies.
3.12
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 6:
Radio frequency environments
Test
Description
Performance
level
Reference
standard
Electrostatic discharge
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
EN 61000-4-2: 95
Radiated RF immunity
80 to 2000 MHz, 10 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz
A
EN 61000-4-3: 96
ENV 50204: 95
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on external I/O
B
EN 61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common, AC mains
B
EN 61000-4-5: 95
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz
sine
A
EN 61000-4-6: 97
Power Frequency H-field
immunity
1 A/m, 50Hz/60Hz, 3 axes
A
EN 61000-4-8: 97
Voltage dips, interrupts
30% Reduction for 25 cycles
>95% Reduction for 250 cycles
>95%, 0.5 cycles
C
C
B
EN 61000-4-11: 94
14
Momentus Thin Product Manual, Rev. C Gen-2
3.13
Reliability
Measurement type
Specification
Nonrecoverable read errors
1 per 1014 bits read, max
Annualized Failure Rate (AFR)
<0.50%
Load/Unload (U/UL)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
To determine the warranty for a specific drive, use a web browser to access the
following web page:
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
You will be asked to provide the drive serial number, model number (or part number)
and country of purchase. After submitting this information, the system will display the
warranty information for your drive.
3.14
Agency certification
3.14.1
Safety certification
These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so
marked as to the certify agency.
3.14.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the
levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are
defined by EN 55022, Class B and the immunity levels are defined by EN 55024.
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the
directives when used in the test systems, we cannot guarantee that all systems will comply with the directives.
The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if
necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should
confirm EMC compliance and provide CE marking for their products.
Korean RRL
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of
Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility
(EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission,
Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic
Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a
Korean-recognized lab.
• Certificate number:
STX-MomentusThin (B)
• Trade name or applicant:
Seagate Technology LLC
• Certificate date:
May 14, 2010
• Manufacturer/nationality:
USA, Singapore and China
Momentus Thin Product Manual, Rev. C Gen-2
15
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ
CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian
Communication Authority (ACA).
3.14.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
16
Momentus Thin Product Manual, Rev. C Gen-2
3.15
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
3.15.1
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured with components and materials that comply with the RoHS
Directive.
3.15.2
China Restriction of Hazardous Substances (RoHS) Directive
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
“O”表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
“X”表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。
3.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Momentus Thin Product Manual, Rev. C Gen-2
17
4.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
4.1
Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
• The drive is fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
4.2
Configuring the drive
Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point
relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the
two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are
Device 0 (master) devices.
Serial ATA drives are designed for easy installation. It is normally not necessary to set any jumpers on this
drive for proper operation. If the host system does not support SATA 3Gb/s operation, place a jumper on pins 1
and 2 to limit the drive to 1.5Gb/s operation.
3.0 Gbits per second operation
Limit data transfer rate to
1.5 Gbits per second
Jumper block
SATA power connector
SATA interface connector
Figure 2. Serial ATA connectors
18
Momentus Thin Product Manual, Rev. C Gen-2
4.3
Serial ATA cables and connectors
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 7
for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind
mateable.
For installations which require cables, you can connect the drive as illustrated in Figure 3.
SATA interface connector
Power connector
SATA interface cable
Power cable
Figure 3. Attaching SATA cabling
Each connector is keyed to ensure correct orientation.
4.4
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only M3 UNC mounting screws.
• Do not overtighten the mounting screws. Maximum torque: 4.0 in-lb (0.4519 N-m).
• Four (4) threads (0.080 inches, 2.032 mm) minimum screw engagement recommended.
• Avoid excessive drive distortion when mounting. Refer to the following specifications for stiffness/deflection
information:
Top cover stiffness/deflection
Operating with no performance degradation, emitted noise,
mechanical damage, or hard errors
10 mm probe: 1.02kgf or
5 mm probe: 0.92kgf
Non-operating with no hard errors
20 mm probe: 2kgf at any point of top cover
20 mm probe: 15kgf at top cover edges only
Momentus Thin Product Manual, Rev. C Gen-2
19
Measurements shown in Figures 4 and 5 are in inches.
Figure 4. Mounting dimensions (for FIPS 140-2 models) — top, side and end view
Warning: FIPS 140-2 Models Contain 3 Tamper Evident Stickers with the marking "Tamper Indicator - Do Not
Remove". These stickers must remain attached to provide the tamper evidence throughout the life of the
drive. Removing these stickers will indicate tampering and void the drive warranty.
20
Momentus Thin Product Manual, Rev. C Gen-2
Figure 5. Mounting dimensions (for standard models) — top, side and end view
Momentus Thin Product Manual, Rev. C Gen-2
21
5.0
About FIPS
The Federal Information Processing Standard (FIPS) Publication 140-2, FIPS PUB 140-2, is a U.S. government computer security standard used to accredit cryptographic modules. It is titled “Security Requirements for
Cryptographic Modules”. The initial publication was on May 25, 2001 and was last updated December 3, 2002.
Purpose
The National Institute of Standards and Technology (NIST) issued the FIPS 140 Publication Series to coordinate the requirements and standards for cryptography modules that include both hardware and software components.
Federal Information Processing Standard (FIPS) 140-2 Level 2 Certification requires drives to go through government agencies certifications to add requirements for physical tamper-evidence and role-based authentication.
Level 2 security
Level 2 improves upon the physical security mechanisms of a Level 1 (lowest level of security) cryptographic
module by requiring features that show evidence of tampering, including tamper-evident coatings or seals that
must be broken to attain physical access to the plaintext cryptographic keys and critical security parameters
(CSPs) within the module, or pick-resistant locks on covers or doors to protect against unauthorized physical
access.
Figure 6. Example of FIPS tamper evidence labels.
22
Momentus Thin Product Manual, Rev. C Gen-2
Note.
May not represent actual drive.
Momentus Thin Product Manual, Rev. C Gen-2
23
6.0
Serial ATA (SATA) interface
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive
also supports the use of the IORDY signal to provide reliable high-speed data transfers.
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT
Attachment” specification.
6.1
Hot-Plug compatibility
Momentus Thin drives incorporate connectors which enable you to hot plug these drives in accordance with
the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be
downloaded from http://www.serialata.org. This device requires a COMRESET from the host after a hotplug
event.
6.2
Serial ATA device plug connector pin definitions
Table 7 summarizes the signals on the Serial ATA interface and power connectors.
Table 7:
Segment
Signal
Serial ATA connector pin definitions
Pin
Function
Definition
S1
Ground
2nd mate
S2
A+
Differential signal pair A from Phy
S3
A-
S4
Ground
2nd mate
S5
B-
Differential signal pair B from Phy
S6
B+
S7
Ground
2nd mate
Key and spacing separate signal and power segments
24
Momentus Thin Product Manual, Rev. C Gen-2
Table 7:
Segment
Power
Serial ATA connector pin definitions
Pin
Function
Definition
P1
V33
3.3V power
P2
V33
3.3V power
P3
V33
3.3V power, pre-charge, 2nd mate
P4
Ground
1st mate
P5
Ground
2nd mate
P6
Ground
2nd mate
P7
V5
5V power, pre-charge, 2nd mate
P8
V5
5V power
P9
V5
5V power
P10
Ground
2nd mate
P11
Reserved
The pin corresponding to P11 in the backplane receptacle connector is also reserved
The corresponding pin to be mated with P11 in the power cable receptacle connector
shall always be grounded
P12
Ground
1st mate.
P13
V12
12V power, pre-charge, 2nd mate
P14
V12
12V power
P15
V12
12V power
Notes:
1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this
case, the mating sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when
installed in a blind-mate backplane configuration.
4. All used voltage pins (Vx) must be terminated.
Momentus Thin Product Manual, Rev. C Gen-2
25
6.3
Supported ATA commands
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See
“S.M.A.R.T. commands” on page 33.for details and subcommands used in the S.M.A.R.T. implementation.
Command name
Command code (in hex)
ATA-standard commands
Device Configuration Restore
B1h/C0h
Device Configuration Freeze Lock
B1h/C1h
Device Configuration Identify
B1h/C2h
Device Configuration Set
B1h/C3h
Download Microcode
92h
Execute Device Diagnostics
90h
Flush Cache
E7h
Flush Cache Extended
EAh
Identify Device
ECh
Initialize Device Parameters
91h
Read Buffer
E4h
Read DMA
C8h
Read DMA Extended
25h
Read DMA without Retries
C9h
Read Long with Retries
22h
Read Long without Retries
23h
Read Multiple
C4h
Read Multiple Extended
29h
Read Native Max Address
F8h
Read Native Max Address Extended
27h
Read Sectors
20h
Read Sectors Extended
24h
Read Sectors without Retries
21h
Read Verify Sectors
40h
Read Verify Sectors Extended
42h
Read Verify Sectors without Retries
41h
Seek
70h
Set Features
EFh
Set Max Address
F9h
Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
Set Multiple Mode
C6h
S.M.A.R.T. Disable Operations
B0h/D9h
S.M.A.R.T. Enable/Disable Autosave
B0h/D2h
26
00H
01H
02H
03H
04H
Momentus Thin Product Manual, Rev. C Gen-2
Command name
Command code (in hex)
S.M.A.R.T. Enable Operations
B0h/D8h
S.M.A.R.T. Enable/Disable Auto Offline
B0h/DBh
S.M.A.R.T. Enable One Attribute Modification
B0h/E0h
S.M.A.R.T. Execute Offline
B0h/D4h
S.M.A.R.T. Read Attribute Thresholds
B0h/D1h
S.M.A.R.T. Read Data
B0h/D0h
S.M.A.R.T. Read Log Sector
B0h/D5h
S.M.A.R.T. Return Status
B0h/DAh
S.M.A.R.T. Save Attribute Values
B0h/D3h
S.M.A.R.T. Write Attribute Thresholds
B0h/D7h
S.M.A.R.T. Write Attribute Values
B0h/E1h
S.M.A.R.T. Write Log Sector
B0h/D6h
Write Buffer
E8h
Write DMA
CAh
Write DMA Extended
35h
Write DMA without Retries
CBh
Write Long with Retries
32h
Write Long without Retries
33h
Write Multiple
C5h
Write Multiple Extended
39h
Write Sectors
30h, 31h
Write Sectors Extended
34h
Write Uncorrectable
45h
ATA-standard power-management commands
Check Power Mode
E5h
Idle
E3h
Idle Immediate
E1h
Sleep
E6h
Standby
E2h
Standby Immediate
E0h
ATA-standard security commands
Security Set Password
F1h
Security Unlock
F2h
Security Erase Prepare
F3h
Security Erase Unit
F4h
Security Freeze Lock
F5h
Security Disable Password
F6h
Momentus Thin Product Manual, Rev. C Gen-2
27
6.3.1
Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following
power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on
page 27. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or
vary with the state of the drive.
The following commands contain drive-specific features that may not be included in the Serial ATA specification.
Word
Description
Value
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
0C5AH
1
Number of logical cylinders
16,383
2
ATA-reserved
0000H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision (8 ASCII character string, padded with blanks
to end of string)
x.xx
27–46
Drive model number: (40 ASCII characters, padded with blanks
to end of string)
ST320LT007 - 9ZV142
ST320LT009 - 9WC142
ST320LT011 - 9ZVG42
ST320LT014 - 9YK142
ST250LT007 - 9ZV14C
ST250LT009 - 9WC14C
ST250LT011 - 9ZVG4C
ST250LT014 - 9YK14C
ST160LT007 - 9ZV14D
ST160LT009 - 9WC14D
ST160LT011 - 9ZVG4D
ST160LT014 - 9YK14D
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple and
Write multiple (16)
8010H
48
Reserved
0000H
49
Standard Standby timer, IORDY supported and may be disabled
2F00H
50
ATA-reserved
0000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired
0200H
53
Words 54–58, 64–70 and 88 are valid
0007H
54
Number of current logical cylinders
xxxxH
0
28
Momentus Thin Product Manual, Rev. C Gen-2
Word
Description
Value
55
Number of current logical heads
xxxxH
56
Number of current logical sectors per logical track
xxxxH
57–58
Current capacity in sectors
xxxxH
59
Number of sectors transferred during a Read Multiple or Write
Multiple command
xxxxH
60–61
Total number of user-addressable sectors
This field contains a value that is one greater than the total number of user-addressable sectors. The maximum value that shall
be placed in this field is 0FFFFFFFh. The 0FFFFFFFh value
applies to all capacities over 137GB (see Section 3.2 and 3.3 for
related information).
ST320LT007 = 0FFFFFFFh
ST320LT009 = 0FFFFFFFh
ST320LT011 = 0FFFFFFFh
ST320LT014 = 0FFFFFFFh
ST250LT007 = 0FFFFFFFh
ST250LT009 = 0FFFFFFFh
ST250LT011 = 0FFFFFFFh
ST250LT014 = 0FFFFFFFh
ST160LT007 = 0FFFFFFFh
ST160LT009 = 0FFFFFFFh
ST160LT011 = 0FFFFFFFh
ST160LT014 = 0FFFFFFFh
62
Retired
0000H
63
Multiword DMA active and modes supported
(see note following this table)
xx07H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word
(120 nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control
(240 nsec)
00F0H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
69–74
ATA-reserved
0000H
75
Queue depth
001FH
76
Serial ATA capabilities
0508H
77
ATA-reserved
0000H
78
Serial ATA features supported
0048H
79
Serial ATA features enabled
0040H
80
Major version number
003EH
81
Minor version number
0028H
82
Command sets supported
306BH
83
Command sets supported
4001H
84
Command sets support extension
4000H
85
Command sets enabled
30xxH
86
Command sets enabled
0001H
87
Command sets enable extension
4000H
88
Ultra DMA support and current mode
(see note following this table)
xx7FH
89
Security erase time
0000H
Momentus Thin Product Manual, Rev. C Gen-2
29
Word
Description
Value
90
Enhanced security erase time
0000H
92
Master password revision code
FFFEH
93
Hardware reset value
(see description following this table)
xxxxH
94
Auto acoustic management setting
xxxxH
95–99
ATA-reserved
0000H
100–
103
Total number of user-addressable LBA sectors available
(see Section 3.2 for related information)
These words are required for drives that support the 48-bit
addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
ST320LT007 = 625,142,448
ST320LT009 = 625,142,448
ST320LT011 = 625,142,448
ST320LT014 = 625,142,448
ST250LT007 = 488,397,168
ST250LT009 = 488,397,168
ST250LT011 = 488,397,168
ST250LT014 = 488,397,168
ST160LT007 = 312,581,808
ST160LT009 = 312,581,808
ST160LT011 = 312,581,808
ST160LT014 = 312,581,808
104–
118
ATA-reserved
0000H
119
Free Fall Protection support (bit 5)
1 = Free Fall Protection supported
0 = Free Fall Protection not supported
120
Free Fall Protection enable/disable (bit 5)
1 = Free Fall Protection feature is enabled
0 = Free Fall Protection feature is disabled
121–
127
ATA reserved
0000H
128
Security status
0001H
129–
159
Seagate-reserved
xxxxH
160–
254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note.
See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:
Description (if bit is set to 1)
30
Bit
Word 63
0
Multiword DMA mode 0 is supported.
1
Multiword DMA mode 1 is supported.
2
Multiword DMA mode 2 is supported.
8
Multiword DMA mode 0 is currently active.
9
Multiword DMA mode 1 is currently active.
10
Multiword DMA mode 2 is currently active.
Momentus Thin Product Manual, Rev. C Gen-2
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
5
Ultra DMA mode 5 is supported
6
Ultra DMA mode 6 is supported
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
14
Ultra DMA mode 6 is currently active.
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
Momentus Thin Product Manual, Rev. C Gen-2
31
6.3.2
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
Table 8:
Set Features command values
02H
Enable write cache (default).
03H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00H Set PIO mode to default (PIO mode 2).
01H Set PIO mode to default and disable IORDY (PIO mode 2).
08H PIO mode 0
09H PIO mode 1
0AH PIO mode 2
0BH PIO mode 3
0CH PIO mode 4 (default)
20H Multiword DMA mode 0
21H Multiword DMA mode 1
22H Multiword DMA mode 2
40H Ultra DMA mode 0
41H Ultra DMA mode 1
42H Ultra DMA mode 2
43H Ultra DMA mode 3
44H Ultra DMA mode 4
45H Ultra DMA mode 5
46H Ultra DMA mode 6
55H
Disable read look-ahead (read cache) feature.
82H
Disable write cache
AAH
Enable read look-ahead (read cache) feature (default).
C1H
Disable the Free Fall Protection feature (41H above enables the Free Fall Protection feature)
F1H
Report full capacity available
Note.
32
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Momentus Thin Product Manual, Rev. C Gen-2
6.3.3
S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
commands and implementation, see the Draft ATA-8 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the
drive uses.
Table 9:
S.M.A.R.T. commands
Code in features register
S.M.A.R.T. command
D0H
S.M.A.R.T. Read Data
D1H
Vendor-specific
D2H
S.M.A.R.T. Enable/Disable Attribute Autosave
D3H
S.M.A.R.T. Save Attribute Values
D4H
S.M.A.R.T. Execute Off-line Immediate (runs DST)
D5H
S.M.A.R.T. Read Log Sector
D6H
S.M.A.R.T. Write Log Sector
D7H
Vendor-specific
D8H
S.M.A.R.T. Enable Operations
D9H
S.M.A.R.T. Disable Operations
DAH
S.M.A.R.T. Return Status
Note.
If an appropriate code is not written to the Features Register, the command is aborted and 0x 04
(abort) is written to the Error register.
Momentus Thin Product Manual, Rev. C Gen-2
33
34
Momentus Thin Product Manual, Rev. C Gen-2
Index
A
ACA 16
acoustics 5, 14
Active mode 11
Address 26
AFR 15
Agency certification 15
Altitude 12
Altitude, nonoperating 5
Altitude, operating 5
Ambient temperature 5, 12
ambient temperature 7
Annualized Failure Rate 15
Annualized Failure Rate (AFR) 5
Areal density 4, 7
ATA commands 26
ATA data-transfer modes supported 4
Australia/New Zealand Standard AS/NZ CISPR22 16
Australian Communication Authority (ACA) 16
Australian C-Tick 16
Average seek time 7
Average seek, read 4
B
bels 5
BPI 4
buffer 4, 7
Bytes per physical sector 4, 6
C
cables and connectors 19
Cache 4
cache 7
capacity 6
CE mark 15
certification 15
Check Power Mode 27
chemical substances 17
China RoHS directive 17
Class B computing device 16
compatibility 15
Conducted noise 10
Conducted RF immunity 14
Configuring the drive 18
connectors 19
CSA60950-1 15
current 4
cycles 15
Cylinders 6
Momentus Thin Product Manual, Rev. C Gen-2
D
data-transfer rates 2
DC power 8
Default logical geometry 6
density 4
Device Configuration Freeze Lock 26
Device Configuration Restore 26
Device Configuration Set 26
Diagnostics 26
dimensions 20, 21
Disks 4
dissipation 8
Download Microcode 26
E
Electrical fast transient 14
Electromagnetic compatibility 15
Electromagnetic Compatibility (EMC) 15
Electromagnetic Compatibility control Regulation 15
Electromagnetic Compatibility Directive (2004/108/
EC) 15
Electromagnetic immunity 14
Electrostatic discharge 14
electrostatic discharge (ESD) 18
EN 55022, Class B 15
EN 55024 15
EN60950 15
Environmental protection 17
Environmental specifications 12
error-correction algorithms 2
errors 5, 15
ESD 18
EU 15
European Union (EU) requirements 15
European Union Restriction of Hazardous Substances 17
evice Configuration Identify 26
Execute Device Diagnostics 26
F
FCC verification 16
features 2
Federal Communications Commission 16
Federal Information Processing Standard 22
FIPS 22
Flush Cache 26
Flush Cache Extended 26
Formatted capacity 4, 6
Freeze Lock 26
G
geometry 6
gradient 5
35
Guaranteed lba 4, 6
guaranteed sectors 6
H
handling 18
Handling precautions 18
heads 6
Height 4
height 7
Humidity 12
humidity 5
I
I/O data-transfer rate 4, 7
Identify 26
Identify Device 26
Identify Device command 28
Idle 8, 27
Idle and Standby timers 11
Idle Immediate 27
Idle mode 5, 11
Idle mode power 8
Information Technology Equipment (ITE) 15
Initialize Device Parameters 26
Input noise ripple 10
Interface 7
interface 24
Interleave 7
Internal data transfer rate 4
Internal data-transfer rate 7
ITE 15
N
National Institute of Standards and Technology 22
NIST 22
noise 10
nominal power 7
Nonoperating shock 13
Nonoperating vibration 13
Nonrecoverable read errors 5
nonrecoverable read errors 15
O
Operating shock 13
Operating vibration 13
P
Physical characteristics 7
Physical organization 6
Physical read/write heads 4
point-to-point 3, 18
Power consumption 8
power dissipation 8
power management 11
power on/off cycles 15
Power specifications 8
Power-management modes 11
Power-on to Ready 8
Power-on to ready 4
precautions 18, 19
programmable power management 11
Q
K
quick reference 4
KCC 15
Korean Communications Commission 15
Korean RRL 15
R
L
latency 4
LBA mode 6
Length 4
length 7
Load/Unload 15
logical geometry 6
M
master/slave 3
Max Address 26
maximum temperature 12
Microcode 26
mounting 19
mounting screws 13
mounting the drive 18
36
Radiated RF immunity 14
Radio and television interference 16
radio frequency (RF) 14
random track location 8
Read Buffer 26
Read DMA 26
Read DMA Extended 26
Read DMA without Retries 26
read errors 5, 15
Read Long with Retries 26
Read Long without Retries 26
Read Multiple 26
Read Multiple Extended 26
Read Native Max Address 26
Read Native Max Address Extended 26
Read Sectors 26
Read Sectors Extended 26
Read Sectors without Retries 26
Read Verify Sectors 26
Momentus Thin Product Manual, Rev. C Gen-2
Read Verify Sectors Extended 26
Read Verify Sectors without Retries 26
Read/write heads 6
Read/write power 5
read/write power and current 8
Recording density 4, 7
Recording method 7
Recording technology 7
Relative humidity 5, 12
Reliability 15
resistance 10
Retries 26
RF 14
RoHS 17
RPM 4
RRL 15
S
S.M.A.R.T. 27
S.M.A.R.T. implementation 26
Safety certification 15
SATA 7, 24
screws 13, 19
sector 6
Sectors per track 6
Security Disable Password 27
Security Erase Prepare 27
Security Erase Unit 27
Security Freeze Lock 27
Security Set Password 27
Security Unlock 27
Seek 26
seek mode 8
Seek time 7
seek time 4
Seeking 8
Self refresh, low power 11
Serial ATA 7
Serial ATA (SATA) interface 24
serial ATA ports 3
servo electronics 8
Set Features 26
Set Max Address 26
Set Multiple Mode 26
Shock 13
Shock, nonoperating 5
Shock, operating 5
single-track seeks 7
Sleep 8, 27
Sleep mode 5, 11
sound power 5
Specification summary table 4
Spindle speed 4, 7
Spinup 8
spinup power 8
Momentus Thin Product Manual, Rev. C Gen-2
Standby 8, 27
Standby Immediate 27
Standby mode 5, 8, 11
Standby to Ready 8
Standby to ready 4
Start/stop times 8
Startup current 4
static-discharge 18
support services 1
Surge immunity 14
T
tamper evident stickers 20
technical support services 1
temperature 5, 7, 12
Temperature gradient 5, 12
timers 11
TPI 4
Track density 4, 7
Track-to-track seek time 4, 7
U
UL60950-1 15
V
Vibration 13
Vibration, nonoperating 5
Vibration, operating 5
Voltage dips, interrupts 14
Voltage tolerance 5, 10
W
Warranty 15
Weight 4
weight 7
Wet bulb temperature 5, 12
Width 4
width 7
Write Buffer 27
Write DMA 27
Write DMA Extended 27
Write Long with Retries 27
Write Long without Retries 27
Write Multiple 27
Write Sectors 27
Write Sectors Extended 27
write uncorrectable 27
37
38
Momentus Thin Product Manual, Rev. C Gen-2
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100625253, Rev. C
Download PDF

advertising