APC | InfraStruXure PDU | Specifications | APC InfraStruXure PDU Specifications

40kW InfraStruXure PDU
PD40H5HK1-M
PDRPP1000-M
Operation and Configuration
400/230V
APXXXX
APYYYYi
This manual is available in English on the enclosed CD.
Este manual está disponible en español en el CD-ROM adjunto.
Dieses Handbuch ist in Deutsch auf der beiliegenden CD-ROM verfügbar.
Ce manuel est disponible en français sur le CD-ROM ci-inclus.
Questo manuale è disponibile in italiano nel CD-ROM allegato.
Instrukcja Obslugi w jêzyku polskim jest dostêpna na CD.
Deze handleiding staat in het Nederlands op de bijgesloten cd.
您可以从包含的 CD 上获得本手册的中文版本。
About This Manual
Audience
This manual is intended for end-users of a 40kW InfraStruXure PDU. It covers the operation,
configuration, and customization of the InfraStruXure PDU, and includes basic InfraStruXure system
operation.
Companion manuals
For additional information about the InfraStruXure system, see the following manuals that were
included with the PDU:
• 40kW InfraStruXure System Installation and Start-Up (990-1593A) covers the installation and
start-up of InfraStruXure UPS power distribution to the rack and power distribution within the
rack.
• Certified Electrician’s Instructions (990-1595A) provides specific instructions for the
electrician connecting mains and an Emergency Power Off (EPO) switch to the InfraStruXure
PDU.
For information about specific components in your InfraStruXure system, see the documentation
included with each component. Before installing or operating any component, refer to the safety
instructions in the component’s manual.
The illustrations of products in this manual may vary slightly from the products in your InfraStruXure
system.
How to find updates to this manual
The content in this manual is based on the latest information available at the time of publication. You
can check for updates to this manual by clicking on the User Manuals link on the Support page of
the APC Web site (www.apc.com). In the list of InfraStruXure Power Distribution Unit manuals,
look for the latest letter revision (A, B, etc.) of the part number on this manual.
40kW InfraStruXure PDU—Operation and Configuration
i
Contents
Safety ......................................................................1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Save these instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety symbols used in this manual . . . . . . . . . . . . . . . . . . . 1
Cross-reference symbols used in this manual . . . . . . . . . . . . . 1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation/Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Maintenance performed while the
PDU is receiving input power . . . . . . . . . . . . . . . . . . . . . . . 2
Total power off procedure . . . . . . . . . . . . . . . . . . . . . . . . . 3
DANGER—Risk of Electric Shock! . . . . . . . . . . . . . . . . . . . . . 3
Emergency Power Off (EPO) . . . . . . . . . . . . . . . . . . . . . . . . 3
EMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Overview .................................................................5
InfraStruXure PDU Components . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front view (interior) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Rear view (interior) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PDU monitoring unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
User connection plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PDU Display Interface.............................................11
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Top-level status screens . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Top-level menu screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Navigating through screens . . . . . . . . . . . . . . . . . . . . . . . 12
Password-protected screens . . . . . . . . . . . . . . . . . . . . . . . 13
Load-Meter Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Volt-Meter Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
40kW InfraStruXure PDU—Operation and Configuration
iii
Contacts Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
How to connect contacts to the PDU monitoring unit . . . . . . 18
Breakers Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Alarms Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
View Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Alarm/Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Alarm Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Alarm Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PDU Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Panel Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Branch Ckt Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Branch Ckt Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Panel Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Global Panel Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Config Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
System/Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Manufacturer Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Firmware Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System Operation .................................................. 29
How to Transfer the UPS into
Maintenance Bypass Operation . . . . . . . . . . . . . . . . . . . . . . . . 29
How to Return from Maintenance Bypass Operation . . . . . . . . 32
How to Ensure Total Power Off . . . . . . . . . . . . . . . . . . . . . . . . 35
How to Apply Power to the System . . . . . . . . . . . . . . . . . . . . . 37
Communication Configuration ............................... 41
InfraStruXure PDU Management Options . . . . . . . . . . . . . . . . . 41
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
InfraStruXure Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Network management interfaces . . . . . . . . . . . . . . . . . . . . 41
Configuring the InfraStruXure Manager . . . . . . . . . . . . . . . . . . 42
iv
40kW InfraStruXure PDU—Operation and Configuration
Configuring the Network Management Interface . . . . . . . . . . . 43
Connect the PDU to your network . . . . . . . . . . . . . . . . . . . 43
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 44
TCP/IP configuration methods . . . . . . . . . . . . . . . . . . . . . . 44
Device IP Configuration Wizard . . . . . . . . . . . . . . . . . . . . . 44
BOOTP & DHCP configuration . . . . . . . . . . . . . . . . . . . . . . 45
Local access to the control console . . . . . . . . . . . . . . . . . . . 47
Remote access to the control console . . . . . . . . . . . . . . . . . 47
Control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
How to Access a Network Management
Interface on a Configured PDU . . . . . . . . . . . . . . . . . . . . . . . . 49
Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Telnet and SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
FTP and SCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
How to Recover From a Lost
Network Management Interface Password. . . . . . . . . . . . . . . . 52
Customizing and Updating the PDU .......................53
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 53
PDU Orderable Part List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
How to Add Circuit Breakers and Power Cables . . . . . . . . . . . . 55
Add a circuit breaker on the PDU . . . . . . . . . . . . . . . . . . . . 55
Add a power cable to the PDU
. . . . . . . . . . . . . . . . . . . . . 55
How to Connect User Input Contacts and
Relay Outputs to the PDU User Connection Plate . . . . . . . . . . . 57
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
How to connect contacts to the PDU monitoring unit . . . . . . 58
How to Test the Emergency Power Off Switch . . . . . . . . . . . . . 59
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Testing the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
How to Download Firmware Upgrades . . . . . . . . . . . . . . . . . . . 63
40kW InfraStruXure PDU—Operation and Configuration
v
Specifications ........................................................ 65
Product Information .............................................. 69
InfraStruXure Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . 69
Life-Support Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
How to Obtain Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Appendix A: Changes in This Manual..................... 73
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
General changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Changes by page number . . . . . . . . . . . . . . . . . . . . . . . . . 73
vi
40kW InfraStruXure PDU—Operation and Configuration
Safety
Overview
Save these instructions
This manual contains important instructions that must be followed during installation, operation, and
maintenance of the InfraStruXure PDU.
Safety symbols used in this manual
Electrical
Hazard
Indicates an electrical hazard, which, if not avoided, could result in injury or
death.
Indicates a hazard, which, if not avoided, could result in personal injury or
damage to product or other property.
Warning
Indicates a potential hazard which could result in damage to product or other property.
Caution
Indicates important information.
Note
Indicates a heavy load that should not be lifted without assistance.
Heavy
Indicates a standby state. When in standby, the unit is not operating, but it may still
contain hazardous voltage. It is not safe to service until the equipment is
disconnected from all sources of electrical power.
Cross-reference symbols used in this manual
Indicates that more information is available on the same subject in a different manual.
See also
Indicates that more information is available on the same subject in a different section
of this manual.
40kW InfraStruXure PDU—Operation and Configuration
1
Warnings
Installation/Maintenance
Only a certified electrician can:
• Connect the InfraStruXure PDU to Mains
• Connect a switch to the EPO interface on the InfraStruXure PDU
Only a certified electrician or an APC Field Service Engineer can:
• Connect the InfraStruXure PDU to the Symmetra PX UPS
• Perform maintenance of the InfraStruXure PDU
When you connect the InfraStruXure PDU to Mains, you must install a 100A (minimum) circuit
breaker to protect the InfraStruXure PDU against over-current. This circuit breaker must have a CE
Mark and a certification mark by a certified body such as VDE, SEV, BSE, KEMA, or Semko.
Maintenance performed while the PDU is receiving input power
APC does not recommend that you perform maintenance of the PDU while it is receiving input
power. However, due to the critical nature of data center loads, this may occur. If you must perform
maintenance while the PDU is receiving input power, observe the following precautions to reduce the
risk of electric shock:
1. Never work alone.
2. Perform the maintenance only if you are a certified electrician who is trained in the hazards of
live electrical installation.
3. Know the procedure for disconnecting electricity to the PDU and the data center in case of an
emergency.
4. Wear appropriate personal protective equipment.
5. Use double-insulated tools.
6. Always follow local and site regulations when working on the PDU.
2
40kW InfraStruXure PDU—Operation and Configuration
Safety
Total power off procedure
1. Set the Symmetra PX UPS System Enable switch to Standby.
2. Set the Symmetra PX UPS DC Disconnect switch to Off.
3. Set the InfraStruXure PDU Main Input breaker (or switch) to Off.
4. Set the DC Disconnect breaker of each XR Battery Enclosure to Off.
5. Set the upstream Mains circuit breaker to Off.
6. Disconnect the batteries in the UPS by pulling them out approximately one inch (25.4mm) from
their normal position.
7. Disconnect the batteries in the XR Battery Enclosure by pulling them out approximately one
inch (25.4mm) from their normal position.
DANGER—Risk of Electric Shock!
Hazardous, live parts inside the Symmetra PX UPS are energized from the battery
supply even when the AC power is disconnected.
Electrical
Hazard
Hazardous, live parts may exist inside the InfraStruXure PDU because of the
Symmetra PX UPS inverter even when the AC power is disconnected. Test any
electrical parts before touching them.
Emergency Power Off (EPO)
This InfraStruXure PDU and Symmetra PX UPS are provided with an Emergency Power Off switch
connection. When this EPO switch is energized, electrical power to the units is de-energized and the
system will not transfer to on-battery operation.
EPO can be achieved with either a contact closure or application of an external 24VAC or 24VDC
from a SELV or PELV source. It’s important to note that hazardous voltage from the Mains voltage
must be isolated from the contact closure or 24VAC, 24VDC. The EPO circuit contact closure, the
24VAC or the 24VDC are considered a SELV circuit as defined in EN 60950 Safety of Information
Technology Equipment or PELV circuit as defined in IEC 60364-4-41 Electrical Installations of
Buildings, Protection for Safety—Protection Against Electric Shock. SELV is an abbreviation for
Safety Extra Low Voltage. PELV is an abbreviation for Protective Extra Low Voltage. SELV and
PELV circuits are isolated from the Mains through a safety isolating transformer, and are designed so
that under normal conditions the voltage is limited to 42.4 Vpeak or 60 VDC.
EMI
WARNING –- This is a Class A product. In a domestic environment, this product may cause radio
interference in which case, the user may be required to take adequate measures. This equipment has
been tested and found to comply with EN55022 (1998) and EN55024.
40kW InfraStruXure PDU—Operation and Configuration
3
Overview
InfraStruXure PDU Components
Front view
 The PDU Shielding Trough
accommodates the power
cables exiting the roof of the
PDU, and it separates power
cables from data cables.
 The PDU power cables supply
power to equipment racks; they
are fed through knockouts on
the top of the PDU. The
number of power cables
installed in the PDU depends
on your system configuration.
Each power cable terminates
with an IEC 309 outlet, which
accepts a variety of APC
InfraStruXure rack-mount
power distribution accessories.


 Cable access holes allow
access for Symmetra PX UPS
input and output wiring. During
installation, the APC Field
Service Engineer exchanges
side panels between the PDU
and the UPS so that the

adjacent sides of the two units
have panels with cable access
holes.


 Leveling feet adjust to level the enclosure. All enclosures must be level before installation of
the system begins.
 The display interface provides a local interface for viewing status data. It has an LCD, fivebutton interface, basic status lights, and a beeper.
40kW InfraStruXure PDU—Operation and Configuration
5
Overview
Front view (interior)
!

!

!
 The 42-position circuit breaker panels provide 84 total single pole positions. Each
single pole provides power at 230 volts L-N. The amperage each position provides
depends on the size of the circuit breaker used.
 The document pocket provides storage of documents relating to the circuit breaker
panels, such as the PDU Panel Board Schedules (provided).
 The wraparound maintenance bypass panel holds three circuit breakers that allow
the UPS to be electrically isolated from the mains, while maintaining the power
panels. The input circuit breaker is labeled Q1, the output circuit breaker is labeled
Q2, and the maintenance bypass circuit breaker is labeled Q3. The label on the
maintenance bypass panel of the PDU illustrates the power flow, and the H2 and H3
LEDs indicate when it is safe to operate the Q2 and Q3 circuit breakers.
 The user connection plate is connected to the PDU monitoring unit, and provides
easy access to input contact, relay output, network, and EPO connections. Make
connections from inside the enclosure, and route wires through the knockout provided
on the plate.
6
40kW InfraStruXure PDU—Operation and Configuration
Overview
Rear view (interior)


 The load test port allows a
UPS system to be load-tested to
ensure that the system will
operate according to
specifications if a power outage
occurs. (This is an optional
component.)
 The Main Input switch
connects to Mains. The switch
accepts 400V input and
requires L1, L2, and L3 input
conductors for PDUs with a
transformer and L1, L2, L3, and
N input conductors for PDUs
without a transformer.




 The PDU monitoring unit has several current and voltage monitoring boards that report to a
central board assembly located in the PDU monitoring unit. The PDU monitoring unit has one
10BaseT (Cat-5) connection to the Information Controller hub (or switch), four output relay
connections, four input contact connections, and one EPO input connection. For easier access
make these connections at the user connection plate located on the roof of the PDU.
 These fuses protect the silicon-controlled rectifiers in the UPS bypass static switch. The fuses
are present only on PDUs without a transformer.
 The output of the optional isolation input transformer feeds the input circuit breaker of the
maintenance bypass panel.
Note: The secondary side of the optional isolation input transformer should be provided with a
suitable separate connection to an earth electrode.
 The UPS input and output cables connect the PDU to the UPS and are shipped coiled on the
floor of the PDU. The input cables consist of 5 wires: L1, L2, L3, N, and PE. The output cable
consist of 4 wires: L1, L2, L3, and N. Each wire is labeled and corresponds to a terminal on the
Symmetra PX UPS. During installation, the Field Service Engineer will connect the PDU to the
UPS.
40kW InfraStruXure PDU—Operation and Configuration
7
Overview
PDU monitoring unit
 This connection provides the input power for the PDU monitoring

unit. The power is supplied by the monitoring unit circuit breaker
on the front of the PDU. If the panel is on, and the monitoring unit
circuit breaker is closed, the monitoring unit is powered.
 Connects to sensors monitoring values such as, voltage, current,
and power.
 Digital input sensing for monitoring such as circuit breaker status,
8 8 5- 22 8 8
1
14
2

5
18
6
19
7
20
8
21
10
22
monitoring unit using an appropriate communication cable (APC
part number 940-0103). This port is used to configure items
relating to servicing the PDU.
9
 Use the Console port (DB-9) to connect a laptop computer to the
17
power from the AC output of the UPS. If the UPS is powered off,
the LED remains lit—the EPO function is still available; however
the monitoring unit is not powered.
15
 The Power LED indicates whether the monitoring unit is receiving

3
PDU display interface.
16
U S ER / E PO C O N TA C TS

 The Display port (RJ-45) connects the PDU monitoring unit to the
4

TO U P S
transformer temperature, fans, etc.
11
24
12
25
STATU S
TR IPP ED
13
D ISP L AY
R S-2 3 2
C O N S O LE PO R T
EPO
TE ST
NC


A R M ED

NO


PO W ER


9 6 00 -8 -N -1

10 = G R N
1 00 = O R N
 When the EPO Arm/Test rocker is in the Test position, engaging
N ET W O R K

R E SE T
switch that is connected—Normally Open (NO) or Normally
Closed (NC).
the EPO switch will not cause the load to be powered off. When the
rocker is in the Armed position, engaging the EPO switch will
cause the PDU’s main input switch and the Symmetra PX UPS to
be switched OFF. See “How to Test the Emergency Power Off
Switch” on page 59 for more information on testing the EPO
switch.
23
LIN K R X /TX
 EPO DIP switches configure the EPO input for the type of EPO
 The EPO Armed LED is green when the rocker is in the Armed
position. The LED is dark when the rocker is in the Test position.
 The EPO Tripped LED is red when the EPO switch is engaged
(the EPO button is pressed), regardless of the state of the EPO
Arm/Test rocker.
 The Reset button resets the network processor; it does not reset the PDU or the PDU monitoring unit.
 Connect to the InfraStruXure Manager through the network port.
 The To UPS port connects the PDU monitoring unit to the Maintenance Bypass/PCB board and the EPO board
inside the Symmetra PX UPS. This port is connected to wire harnesses secured inside the PDU that are
connected to the Symmetra PX UPS during installation of the system.
 The optional User/EPO Contacts port is connected to wire harnesses that connect to the User Connection Plate
in the roof (or floor) of the PDU. The port allows for relay outputs (4), input contacts (4), and an EPO input (1).
See “Contacts Screen” on page 16 and “How to Test the Emergency Power Off Switch” on page 59.
Note
8
The branch current monitoring boards connect to the Branch Current Monitor ports (RJ-11). These
ports are on the top side of the PDU monitoring unit, and are labeled on the face of the unit. Each port
corresponds to a section of circuit breakers on the PDU distribution circuit breaker panel:
upper left=[01..41]; upper right=[02..42]; lower left=[43..83]; lower right=[44..84].
40kW InfraStruXure PDU—Operation and Configuration
Overview
User connection plate
For a description and location of the user connection plate, see () on page 6. For clarity, refer to the
following illustration which shows the user connection plate in greater detail.
!

USER INTERFACE
© 2001 APC
MADE IN USA
ATS 1
Contact Outputs
ATS 2
4
ATS EN
2
3
Contact Inputs
ATS 0
1
!
– +
EPO 24V EPO
AC/DC Contact
!
 Connect the InfraStruXure PDU to the network or the InfraStruXure Manager through the
ethernet port.
 The user connection plate has four input contact connections for monitoring Normally
Open (NO) or Normally Closed (NC) dry contacts. See page 58 for more information.
 The user connection plate has four relay output connections for connection of Normally
Open (NO) or Normally Closed (NC) dry contacts. See page 58 for more information.
 Connect an Emergency Power Off (EPO) switch at one of the three choices of EPO
connections (24VDC, 24VAC, or contact closure). See page 59 for more information.
40kW InfraStruXure PDU—Operation and Configuration
9
PDU Display Interface
Overview
You can use the display interface to configure settings, set alarm thresholds, and provide audible and
visual alarms.
Load
Powered
ESC
Check
Log
?
Bypass
Alarm
   


  

Load Powered
LED
When green, all output phases are within the limits specified by
the output alarm limit thresholds.

Check Log LED
When yellow, at least one new alarm condition has been detected.

Bypass LED
When yellow, power to the load is being supplied directly by the
utility power source—the UPS has been removed from the circuit
for maintenance or replacement. Bypass breakers on the PDU
function as input circuit breakers to protect the load equipment.

Alarm LED
When red, an alarm condition exists.

LCD
View alarms, status data, instructional help, and configuration
items.

Up and Down
navigation keys
Selects menu items and accesses information.

ENTER key
Opens menu items and inputs changes to system parameters.

HELP key
Launches context-sensitive help. Press the HELP key for
information about each item on the screen and for instructions on
how to perform certain tasks (i.e. placing the UPS into
Maintenance Bypass operation.)

ESC key
Returns to previous screen displayed.
40kW InfraStruXure PDU—Operation and Configuration
11
PDU Display Interface
Top-level status screens
After displaying a brief start-up screen after system start-up, the display interface scrolls
automatically and continuously through four screens of basic status information. Press the Up and
Down arrow keys to interrupt the automatic scrolling to view a specific status screen.
Volts In
L1-2: 000
L2-3: 000
L3-1: 000
Volts Out
L1: 000
L2: 000
L3: 000
Load
L1:
L2:
L3:
Total Output Loading
kW:
000
PF: 000
kVA: 000
%LD: 000
Freq: 00.0
Current
000
000
000
Neut:000
No Active Alarms
System Date/Time:
Jun-24 2003 07:58
Top-level menu screen
On any top-level status screen, press the ENTER key to open the top-level menu screen.
Load-Meter
Volt-Meter
Contacts
Breakers
Alarms
Panel
Config
Help
If the display interface is inactive for the time specified as the Time-out setting, the
interface reverts to the initial basic monitoring screens.
Note
For descriptions of the top-level menu choices, see the individual sections starting on
page 14.
Navigating through screens
To open any screen, press the Up and Down arrow keys until the selector arrow ( rests next to your
desired selection. Press the ENTER key to view the selected screen.
Load-Meter
Volt-Meter
Contacts
Breakers
Alarms
Panel
Config
Help
Contacts In: 02of04
Name: User Switch #2
Normal: Open
Status: Open

When configuring settings, press the Up and Down arrow keys
until the selector arrow ( rests next to the setting you want to
change, and press the ENTER key. If the setting is a list of choices,
an input arrow ( will appear next to the setting. Press the Up and
Down arrow keys until your desired change is listed. Press the
ENTER key to select the setting.
12
Contacts In: 02of04
Name: User Switch #2
Normal: Open
Status: Open

40kW InfraStruXure PDU—Operation and Configuration
PDU Display Interface
On some screens, continue arrows ( indicate that there
are additional screens to view in the category. Press the Up
or Down arrow key to view the additional screens.
System/Network
Electrical Configuration
Panel Configuration
Manufacturer Data

Product Data
Factory Defaults
Firmware Updates
Password-protected screens
When configuring or changing settings, you will be prompted for your password. To enter your
password:
1. Press the Up or Down arrow key until the correct letter is
displayed, and then press the ENTER key.
Note
Enter Password:
*******
After you press the ENTER key, the character you
entered is displayed as an asterisk and the input
arrow moves to the next space for you to select
the next password character.
2. Press the ENTER key twice after you enter your password.
See “System Password” on page 26 to change your password.
40kW InfraStruXure PDU—Operation and Configuration
13
Load-Meter Screen
From the Load-Meter screen, you can select the following items:
Total Load by Phase
The load supported by each phase in kVA, in RMS current (Irms),
and as a percentage of the maximum allowable load (%LD).
Total Load Summary For the total load supported:
• kW: The power provided, in kilowatts.
• kVA: The actual power drawn by the load, in kilovolt-amperes.
• Freq: Frequency.
• PF: The power factor (kW/KVA), which affects the power
available to the load.
• %LD: The load as a percentage of the maximum allowable
load.
Power Factor
For each phase:
• kVA: The actual power drawn by the load, in kilovolt-amperes.
• kW: The power, in kilowatts, provided by the phase.
• PF: The power factor (kW/kVA), which affects the power
available to the load.
14
40kW InfraStruXure PDU—Operation and Configuration
Volt-Meter Screen
From the Volt-Meter screen, you can select the following items:
Output Voltage
Displays each phase-to-phase output voltage (e.g., L1-2 for phase L1 to
phase L2) and each phase-to-neutral output voltage (e.g., L1 for phase L1
to neutral).
Input Voltage
Displays each phase-to-phase input voltage (e.g., L1-2 for phase L1 to L2),
or each phase-to-neutral input voltage (e.g., L1 for phase L1 to neutral).
40kW InfraStruXure PDU—Operation and Configuration
15
Contacts Screen
Overview
The PDU can monitor external contact closure events. Possible applications include the following:
• Magnetic contact switches
• Window foil
• Tamper switches
• Heat detectors
• Water sensors
• Pressure sensors
• Building smoke and fire detection systems
You can set input contacts to cause alarm conditions based on their current state and a user-defined
normal state. Relay outputs can map internal alarms and events to outside devices. Use the Contacts
screen to display and configure information about input contacts and relay outputs.
Input Contacts
Scroll through the list to display information about each of the
installed contact inputs. For example, 02of04 displays
information about the second of four installed contact inputs.
• Name—The name of this input contact (Maximum: 14
alphanumeric characters.)
• Normal—The normal position of this input contact, either
Open or Closed.
• Status—The position of this input contact. If the position is
not the normal position, an alarm condition occurs.
Relay Outputs
Scroll through the list to display information about each of the
installed relay outputs. For example, 04of04 displays
information about the fourth of the four available relay outputs.
• Name—The name of this relay output (Maximum: 14
alphanumeric characters).
• Normal—The normal position of this relay output, either
Open or Closed.
• Status—The position of this relay output.
16
40kW InfraStruXure PDU—Operation and Configuration
PDU Display Interface
Alarm Relay Map
Configure the relay outputs, using
Alarm Map: 01 of 04
the Alarm Relay Map. Each
[Vo, By, C4]
Map: Input Voltage
Alarm Map corresponds to an
Apply Now
output relay. For example, Alarm
map 01of04 corresponds to the first of four relay outputs. The second
line, in brackets [ ], lists the items that you have selected to map to the
selected relay. The third line allows you to select the alarms to which
you want to map the relay:
• Any Load (L)—Maps to over- or under-current alarms for
circuit breaker panels and branch circuits.
• Overload (O)—Maps to over-current alarms for circuit breaker
panels, branch circuits, and SYSGND.
• Input Voltage (Vi)—Maps to any input voltage alarm.
• Output Voltage (Vo)—Maps to any output voltage alarm.
• PDU in Bypass (By)—Mapping this option will cause the relay
output to actuate when the Q3 breaker is closed.
• Any Breaker (Br)—Mapping this option will cause the relay
output to actuate when the input, bypass input (Q10), or crosstie output breaker is not in its normal state.
• Contacts 1–4 (C1, C2, C3, C4)—Maps to the input contact
alarms.
Before exiting the screen, to save your changes, select the Apply
Now option on the bottom line of the screen.
40kW InfraStruXure PDU—Operation and Configuration
17
PDU Display Interface
How to connect contacts to the PDU monitoring unit
1. Choose one or more contact number(s) on the User/EPO contacts port on the user connection
plate to which you will connect the contacts. The user connection plate connects to the PDU
monitoring unit.
2. From the PDU display interface:
a. Press the ESC or ENTER key to go to the top-level menu screen.
b. Select Contacts on the top-level menu screen, and press the ENTER key.
Load-Meter
Volt-Meter
Contacts
Breakers
Alarms
Panel
Config
Help
c. Select Contact Inputs (or Relay Outputs) and press ENTER to display the contact inputs (or
relay outputs) screen.
>Contact Inputs
>Relay Outputs
>Alarm Relay Map
d. Select Contact In and press the ENTER key to select the number of the contact you are
connecting. The continue arrow will appear next to the contact number.
Contact In:01of04
Name: User Contact1
Normal:Open
Status: Closed
e. Press the Up or Down arrow key to select the appropriate contact number, and press the
ENTER key.
f. Press the Down arrow key to enter a unique Name for the contact and to configure the
Normal state of the contact (Open or Closed). The default Normal state is Open. Press the
ENTER key to select the item to configure.
You will be prompted for your password to configure these items.
Note
3. Connect contact wires (300V-rated cabling required) to the User Contacts terminal block on
the user connection plate. You will need a 2.5-mm standard screwdriver.
4. Run the wires from the terminal block out the roof or under the floor of the PDU to your
contact’s location.
Ensure that wires are properly retained and away from high voltage lines and
breakers.
Warning
See “Relay Outputs” on page 66 for relay output specifications.
18
40kW InfraStruXure PDU—Operation and Configuration
Breakers Screen
Use the Breakers screen to view the status of the system and PDU circuit breakers.
UPS & System Bypass Reports the operation mode of the UPS and the state of the Q1,
Q2, and Q3 circuit breakers on the PDU.
Main Input
Reports status of PDU Main Input Switch (Open or Closed).
Under normal operation, this switch is Closed.
40kW InfraStruXure PDU—Operation and Configuration
19
Alarms Screen
View Active Alarms
Use this option of the Alarms screen to display active alarms (alarms that have not been resolved).
Scroll through the list to view each active alarm.
Alarm/Event Log
Use this selection of the Alarms screen to access the following options:
New Logged Items
Display a description and the date and time of each alarm that
occurred since the last time this option was used. The date/time
format is mm/dd/yyyy hh:mm:ss.
• The most recent alarm is displayed initially.
• If the log contains no alarms, the screen displays Alarm Log
Empty.
Entire Log
Display a description and the date and time of each alarm in the
alarm log. The date/time format is mm/dd/yyyy hh:mm:ss.
• The most recent alarm is displayed initially. To move to the
previous alarm press the Down arrow key. To move to the next
most recent alarm, press the Up arrow key.
• If the log contains no alarms, the screen displays Alarm Log
Empty.
Clear Log
20
Delete the contents of the alarm log.
40kW InfraStruXure PDU—Operation and Configuration
PDU Display Interface
Alarm Setup
Use this option of the Alarms screen to access the following options:
Loading Limits
Configure the following in amps and as a percentage of full load:
• Out High: The upper limit for output current.
• Out Low: The lower limit for output current.
• Out Neut: The upper limit for current on the neutral wire for
the output phases.
Voltage Limits
Configure the following as a percentage under or over the rated
voltage:
• Input: The allowed range for input voltage.
• Output: The allowed range for output voltage.
Other Limits
Configure these limits:
Frequency: The frequency variation, in hertz, that is
acceptable for the output current.
Global Alarm Config
Set all the loading limits or all the voltage limits simultaneously as
a percentage of full load:
• Load Limits: Set the same percentage for the upper limit for
output current, the lower limit for output current, and the
upper limit for current on the neutral wire for the output
phases. (Use the Loading Limits option to set these
thresholds individually.)
• Volt Limits: Set the same percentage for the high and low
thresholds for input and output voltage. (Use the Voltage
Limits option to set these thresholds individually.)
Select Apply Now and then YES to implement your changes.
Alarm Beeper
Use this option of the Alarms screen to turn the alarm beeper ON or OFF.
40kW InfraStruXure PDU—Operation and Configuration
21
PDU Display Interface
PDU Alarms
This table lists all alarms that can be generated by the InfraStruXure PDU, as displayed by the All Possible
Alarms option, with numeric variables between the < > characters. Logged alarms will display specific
numbers instead.
Alarm Condition
22
Explanation
Input V <Ln-N> =<Value>
Voltage Under Limit
Input voltage of the phase indicated has dropped below the
configured lower limit.
Input V <Ln-N> =<Value>
Voltage Over Limit
Input voltage of the phase indicated exceeded the configured
upper limit.
Output V <Ln-N> =<Value>
Voltage Under Limit
Phase-to-neutral output voltage for phase <L-N> dropped below
the configured limit.
Output V <Ln-N>=<Value>
Voltage Over Limit
Phase-to-neutral output voltage for phase <L-N> exceeded the
configured limit.
Output I L<n>=<Value>
Current Over Limit
Current of output phase <n> exceeded the configured limit.
Output I L<n>=<Value>
Current Under Limit
Current of output phase <n> dropped below the configured limit.
Output Neut=<Value>
Current Over Limit
Current on the neutral wire for the output phases exceeded the
configured limit.
Output FDev=<Value>
Freq Out of Range
Frequency of the output current is above or below the range that
is configured as acceptable.
Input Transformer Temperature
Too High
The temperature of the PDU transformer exceeded the normal
limit (if applicable).
Main Breaker Open
Alarm Active
The Main Input switch is Off.
<User Contact Name>
Alarm Active
A user-configured contact connected to the PDU monitoring unit
is reporting an alarm condition.
No UPS Input
Breaker Q1 Open
The Q1 circuit breaker is open, and the PDU is not receiving
power from the UPS.
No Panel Feed
Breakers Q2 & Q3 Open
The Q2 & Q3 circuit breakers are open, and the PDU is not
supporting connected equipment.
Atypical Bypass Mode
Alarm Active
The system state as set by the Q1, Q2, & Q3 breakers is in a
bypass mode.
Branch Ckt Pos: <nn>
Current Over Limit
Current on one of the poles of branch circuit breaker <nn>
exceeded the configured limit.
Branch Ckt Pos: <nn>
Current Under Limit
Current on one of the poles of branch circuit breaker <nn>
dropped below the configured limit.
Fan Rotation Failure
Alarm Active
There is a failure in one of the fans. The fan needs to be replaced
(if applicable).
40kW InfraStruXure PDU—Operation and Configuration
Panel Screen
Branch Ckt Loading
You can display Branch Ckt Loading (Branch Circuit Loading) status if the option to measure
current at the distribution circuit breakers is installed.
You can view data for each individual panel position on the distribution panel. To view status of a
panel position, select the range that includes the position.
Branch Ckt Loading
Select Range:
[01..41] [02..42]
[43..83] [44..84]
The top line of selections on the screen applies to the top distribution circuit breaker panel on the
PDU. The bottom line of selections applies to the bottom distribution circuit breaker panel on the
PDU. The panel position numbers on the screen correspond to the numbers on the distribution panel.
(Odd numbers are on the left; even numbers are on the right.)
Once you have selected the correct range, press the Up and Down arrow keys to scroll through the list
of circuit breakers in the selected range. Poles that are tied together will be shown on the same screen.
Ckt: 03of21 Irms %LD
05: 16A
11.3 56.5
In the example above, the screen shows the third circuit breaker of 21 circuit breakers in the selected
range. This is a single-pole circuit breaker, occupying panel position 05. The circuit breaker is rated
at 16 amps. The following data are displayed for each pole:
• Irms: Measured root mean square (RMS) current of the pole position.
• %LD: Present load as a percentage of rated load of the panel position.
Branch Ckt Limits
Available only if the option to measure individual currents is installed, Branch Ckt Limits (Branch
Circuit Limits) accesses a scrollable list of the circuit breakers in the panel. For each circuit breaker,
the screen displays, in the Loading column, the current on each panel position as a percentage of the
rated current. In the Load Alarm column, you can configure the high and low thresholds for the
circuit breaker as a percentage of its rated current. For example, if you set 80% as the high threshold
for a single-pole 16-amp circuit breaker, an alarm condition occurs if the current reaches 12.8 amps.
40kW InfraStruXure PDU—Operation and Configuration
23
PDU Display Interface
Panel Configuration
Configure the branch metering settings for each circuit breaker on
Panel Configuration
the distribution panel, or configure both panels simultaneously.
Select Range:
[01..41] [02..42]
To configure a circuit breaker, select the range that includes the
circuit breaker. The top line of selections on the screen applies to
the top distribution circuit breaker panel on the PDU. The bottom line of selections applies to the
bottom distribution circuit breaker panel on the PDU. The panel position numbers on the screen
correspond to the numbers on the distribution panel. (Odd numbers are on the left; even numbers are
on the right.) Once you have selected the correct range, configure the settings for each circuit breaker
in the range:
Pos: The panel positions in the selected range.
Breaker: Two configurable items:
• The circuit breaker rating, in amps.
• The circuit breaker tie indicator: Define the number of panel positions associated. You can
associate positions with circuit breakers, which enables you to view status about each circuit
breaker and receive alarm notification when any of a circuit breaker’s poles are above or below
the configured branch circuit limit. You can also associate panel positions that are logically tied
together. For example, you can associate together panel positions for three separate circuit
breakers that are connected to the same PDU power cord and that feed power to the same
equipment enclosure.
To configure the values on this screen:
1. From the first column, use the arrow keys to scroll up or down to the pole position you want to
configure.
2. Press the ENTER key to move to the item you want to configure in the third column (the circuit
breaker rating or the circuit breaker tie indicator).
3. Scroll again to select the value you want for the circuit breaker rating or the circuit breaker tie
indicator. To associate one panel position with the next position in the list, choose the +
character as the tie indicator immediately following the circuit breaker rating. To indicate that
the position is not associated with the next panel position in the list, choose the ] character as
the tie indicator immediately following the circuit breaker rating. When you change the + or ]
character that follows the circuit breaker rating in one row, the + or [ character before the
circuit breaker rating in the next row also changes to indicate the changed association between
the panel positions.
For example, this screen shows three, single-pole, 16A,
associated circuit breakers occupying positions 08, 10, and
12 on the top right distribution panel.
24
Pos
08
10
12
40kW InfraStruXure PDU—Operation and Configuration
Breaker
[ 16A +
+ 16A +
+ 16A ]
PDU Display Interface
Global Panel Config
Configures the same number of poles or circuit breaker ratings for all circuit breakers in both
distribution panels simultaneously. For example, if your system uses only 3-pole, 16-amp circuit
breakers, choose this option, scroll to the value 3 for Poles and 16 for Amp Rating, and then select
Apply Now and YES to implement your changes.
40kW InfraStruXure PDU—Operation and Configuration
25
Config Screen
System/Network
Use this option of the Config screen to access these options:
System Password
• Password: Change the system password required to access
protected screens and fields in the display interface. Enter a
string of up to eight alphanumeric characters, followed by the
underline character ( _ ) to indicate the end of the string. The
default password is APC.
• Time-out: Set the time that the display interface waits for user
input before it reverts to the initial scrolling of status screens.
Select 1, 2, 5, 10 (the default), or 30 minutes; or 1, 2, or 4 hours,
or Forever.
• Invalidate NOW: Re-enter the system password for viewing
password-protected screens.
Date/Time
• Date: Set in the following format: dd/mm/yyyy.
• Time: Set in the following format: hh:mm:ss.
Local Interface
• Contrast: Set the screen contrast for the LCD. Select from 1
(high contrast) to 8 (low contrast).
• Key Click: Choose On for an audible click whenever you press
a navigation key. Choose Off to disable the key click.
• Beeper: Select High, Medium, Low, or Off to adjust the
loudness of the audible beeper and the key click.
Network Address
The following values are set by the Information Controller during
initial configuration:
• IP: The System IP address, which the domain name server
translates into a domain name.
• Mask: The subnet mask, which identifies the subnetwork on
which the InfraStruXure PDU operates.
• GW: The Gateway address. This is the physical address of the
InfraStruXure PDU, expressed as a 48-bit hexadecimal number.
26
40kW InfraStruXure PDU—Operation and Configuration
PDU Display Interface
Electrical Config
This option of the Config screen displays information about the electrical service that provides input
to the InfraStruXure PDU. All of the values displayed on this screen are set at the factory. Use this
information when viewing and setting alarms.
Input Config
Configure the following items:
• Main Input: The voltage from the building’s electrical
service coming into the PDU main input switch.
• 3W: 3-phase Delta, measured line-to-line
• 4W: 3-phase Wye, measured line-to-neutral
• Transformer: Indicates whether the InfraStruXure PDU has
the optional isolation input transformer.
• Bypass Input: Indicates whether the PDU has a bypass input
switch (B).
• Fuse: Indicates whether the PDU has fuses protecting the
SCRs in the UPS. The fuses are present only on single-feed
PDUs without a transformer.
Output Config
Configure the following items:
• Panel Voltage: The nominal voltage of the distribution panels
supplying power to the load equipment. (This is measured
line-to-neutral.)
• Panel Breaker: The rating, in amps, of the circuit breaker
feeding the distribution panels.
Other Config Items
Configure the following items:
• Load Test Port: Indicates whether the PDU has a load test
port installed.
• Max. Power: Maximum power of your InfraStruXure PDU
(40kW or 80kW).
40kW InfraStruXure PDU—Operation and Configuration
27
PDU Display Interface
Manufacturer Data
Use this option of the Config screen to display a scrollable list containing information about the
InfraStruXure PDU. This information is useful when requesting service or product updates. The
following information is displayed:
• Manufacturer Name
• Date of Manufacture
• Date of Calibration
• Hardware Revision
• Firmware Revision (for PDU monitoring and metering)
• Serial Number
• Model Number
System ID
Use this option of the Config screen to identify your InfraStruXure PDU. The following fields can be
configured:
Device Name
Set a unique name for your InfraStruXure PDU.
Product Location Name the physical location of the product in your data center.
Product Contact
Identify the person to notify concerning questions or problems with regard
to the product.
Factory Defaults
Use this option of the Config screen to reset all InfraStruXure PDU settings to their factory default
values.
Firmware Updates
Use this option of the Config screen to download updated firmware to the InfraStruXure PDU.
28
40kW InfraStruXure PDU—Operation and Configuration
System Operation
How to Transfer the UPS into Maintenance
Bypass Operation
Note
Select Help from the top-level menu screen of the PDU display interface and select
the first help topic, Putting the PDU into Maintenance Bypass, or follow the
procedure below.
When servicing the System, transfer the System into maintenance bypass operation. When the
System is operating in maintenance bypass, input power flows directly to the PDU and out to the load
equipment.
1. Command the UPS into static bypass operation through the UPS display interface:
a. Press the ESC key at the top-level status screen to
open the top-level menu.
b. Select Control on the top-level menu, and press
the ENTER key.
Top-Level Menu
Control
Status
Setup
Accessories
Logging
Display
Diags
Help
Control Menu
c. Select UPS Into Bypass on the Control menu
and press the ENTER key.
UPS Into Bypass
Do Self Test
Simulate Power Fail
Graceful Reboot
Graceful Turn Off
Start Runtime Cal
Turn Load On
Confirmation Screen
d. Confirm the selection on the next screen: select
Yes, UPS into Bypass, and press the ENTER key.
Confirm
Yes, UPS into Bypass
No, Abort
40kW InfraStruXure PDU—Operation and Configuration
29
System Operation
The UPS BYPASS LED illuminates and the following screens appear:
UPS has been
commanded to go
into Bypass...
UPS load is in Bypass
Press any key...
The H3 LED above the Q3 breaker illuminates, indicating that it is safe to operate
the Q3 breaker.
Note
2. Close (turn ON) the Q3 breaker on the PDU.
The H2 LED above the Q2 breaker illuminates, indicating that it is safe to operate
the Q2 breaker.
Note
3. Open (turn OFF) the Q2 breaker on the PDU.
The UPS will show a Forced Bypass message on the
display interface, and the Fault LED will be red.
30
40kW InfraStruXure PDU—Operation and Configuration
System Operation
4. Set the UPS System Enable switch to OFF, and then
open (turn OFF) the UPS DC Disconnect breaker.
5. If applicable, open (turn OFF) the XR Battery
Enclosure DC Disconnect breaker.
6. Open (turn OFF) the Q1 breaker on the PDU.
The UPS is now in maintenance bypass operation.
40kW InfraStruXure PDU—Operation and Configuration
31
How to Return from Maintenance Bypass
Operation
Note
Select Help from the top-level menu screen on the PDU display interface and select the
second help topic, Returning from PDU Maintenance Bypass, or follow the
procedure below:
1. Close (turn ON) the Q1 breaker on the PDU.
2. If applicable, close (turn ON) the XR Battery
Enclosure DC Disconnect breaker.
3. Set the UPS DC Disconnect breaker to ON and
then set the UPS System Enable switch to ON.
The UPS will show a Forced Bypass message on
the display interface, and the Fault LED will be
red.
32
40kW InfraStruXure PDU—Operation and Configuration
System Operation
4. Command the UPS to apply power to the load:
a. Press the ESC key at the top-level status screen to
open the top-level menu and have access to eight
submenus.
b. Select Control, and press the ENTER key.
Top-Level Menu
Control
Status
Setup
Accessories
Logging
Display
Diags
Help
Control Menu
c. Select Turn Load On from the Control menu, and
press the ENTER key.
UPS Into Bypass
Do Self Test
Simulate Power Fail
Graceful Reboot
Graceful Turn Off
Start Runtime Cal
Turn Load On
Confirmation Screen
d. On the next screen select Yes, UPS Load ON, and
press the ENTER key.
Confirm
Yes, UPS Load ON
No, Abort
The LOAD ON LED illuminates and the interface displays the following two screens:
UPS has been
commanded to turn
load power on...
UPS load is on
Press any key...
5. Command the UPS into static bypass operation through the UPS display interface:
a. Press the ESC key at the top-level status screen to
open the top-level menu.
b. Select Control on the top-level menu, and press the
ENTER key.
Top-Level Menu
Control
Status
Setup
Accessories
40kW InfraStruXure PDU—Operation and Configuration
Logging
Display
Diags
Help
33
System Operation
c. Select UPS Into Bypass on the Control menu, and
press the ENTER key.
Control Menu
UPS Into Bypass
Do Self Test
Simulate Power Fail
Graceful Reboot
Graceful Turn Off
Start Runtime Cal
Turn Load On
Confirmation Screen
d. Confirm the selection on the next screen: select Yes,
UPS into Bypass, and press the ENTER key.
Confirm
Yes, UPS into Bypass
No, Abort
The H2 LED above the Q2 breaker illuminates, indicating that it is safe to
operate the Q2 breaker.
Note
6. Close (turn ON) the Q2 breaker on the PDU.
The H3 LED above the Q3 breaker illuminates, indicating that it is safe to operate
the Q3 breaker
Note
7. Open (turn OFF) the Q3 breaker on the PDU.
The UPS automatically comes out of Static Bypass
operation.
34
40kW InfraStruXure PDU—Operation and Configuration
How to Ensure Total Power Off
1. Command the UPS to turn off power to the load:
a. Press the ESC key at the top-level status
screen to open the top-level menu and have
access to eight submenus.
b. Select Control, and press the ENTER key.
Top-Level Menu
Control
Status
Setup
Accessories
Logging
Display
Diags
Help
Control Menu
c. Select Turn Load Off from the Control
menu, and press the ENTER key.
UPS Into Bypass
Do Self Test
Simulate Power Fail
Graceful Reboot
Graceful Turn Off
Start Runtime Cal
Turn Load Off
Confirmation Screen
d. On the next screen select Yes, UPS Load
OFF, and press the ENTER key.
Confirm
Yes, UPS Load OFF
No, Abort
The LOAD ON LED turns off and the interface displays the following two screens:
UPS has been
commanded to turn
load power off...
UPS load is off
Press any key...
2. Set the UPS DC Disconnect breaker to OFF, and
then set the System Enable switch to OFF.
40kW InfraStruXure PDU—Operation and Configuration
35
System Operation
3. If applicable, set the XR Battery Enclosure DC
Disconnect breaker to OFF.
4. Pull out all battery units in the UPS and XR
Battery Enclosures to the red battery disconnect
line.
5. Set the PDU Main Input switch to OFF.
6. Open (turn OFF) the Q1, Q2, and Q3 breakers
on the PDU.
7. Set the upstream input mains circuit breaker to
the OFF or Locked Out position.
36
40kW InfraStruXure PDU—Operation and Configuration
How to Apply Power to the System
This procedure instructs how to apply power to a system that has already been installed. For initial
start-up instructions, see the InfraStruXure System Installation and Start-Up manual.
1. Set the upstream mains circuit breaker to ON.
2. Set the Main Input switch on the
PDU to ON.
3. Close (turn ON) the Q1 breaker on the
PDU to apply power to the UPS.
4. Ensure that all battery units are pushed all the way into the Symmetra PX UPS and XR
Battery Enclosures and locked into position.
40kW InfraStruXure PDU—Operation and Configuration
37
System Operation
5. Set the UPS DC Disconnect breaker to ON,
and then set the UPS System Enable switch to
ON.
6. If applicable, set the XR Battery Enclosure DC
Disconnect breaker to ON.
When the System Enable switch is placed in the ON position, the Startup screen appears on the
display interface of the Symmetra PX UPS.
PowerView RM
Rev: 000 English
Please wait...
The top-level status screen appears on the display interface. This may take up to 30 seconds.
||||||||||||
Fuel%
|||
Load%
In 400V out000V 50Hz
Runtime: 1hr 2m
38
40kW InfraStruXure PDU—Operation and Configuration
System Operation
7. Read the messages displayed on the UPS display interface:
a. Note any alarms, and verify that they are appropriate
for start-up conditions.
b. Verify that the UPS accepts the input.
Top-Level Status Screen
||||||||||||
Fuel%
|||
Load%
In 400V out000V 50Hz
Runtime: 1hr 2m
8. Command the UPS to apply power to the load:
a. Press the ESC key at the top-level status screen to open
the top-level menu and have access to eight submenus.
b. Select Control, and press the ENTER key.
Top-Level Menu
Control
Status
Setup
Accessories
Logging
Display
Diags
Help
Control Menu
c. Select Turn Load On from the Control menu, and
press the ENTER key.
d. On the next screen select Yes, UPS Load ON, and
press the ENTER key.
UPS Into Bypass
Do Self Test
Simulate Power Fail
Graceful Reboot
Graceful Turn Off
Start Runtime Cal
Turn Load On
Confirmation Screen
Confirm
Yes, UPS Load ON
No, Abort
The LOAD ON LED illuminates, and the interface displays the following two screens:
UPS has been
commanded to turn
load power on...
UPS load is on
Press any key...
40kW InfraStruXure PDU—Operation and Configuration
39
System Operation
9. To apply power to the PDU distribution panel,
close (turn ON) the Q2 breaker on the PDU.
10.To apply power to the PDU power cables and connected equipment, close (turn ON) the
distribution panel breakers.
40
40kW InfraStruXure PDU—Operation and Configuration
Communication Configuration
InfraStruXure PDU Management Options
Overview
You have two management options for the InfraStruXure PDU. You can manage the PDU along with
the rest of your InfraStruXure equipment through the InfraStruXure Manager, or you can manage
your PDU through APC’s network management interfaces.
InfraStruXure Manager
The InfraStruXure Manager is a rack-mount management device that coordinates the management
functions of APC InfraStruXure-Certified devices installed in your data center. It provides one single
interface to view and configure all APC InfraStruXure-Certified devices. See “Configuring the
InfraStruXure Manager” on page 42 for configuration instructions.
For more information about the InfraStruXure Manager, see the Installation and
Configuration manual included with the InfraStruXure Manager.
See also
Network management interfaces
The control console and Web interfaces provide menus with options that allow you to manage the
InfraStruXure PDU. See “Configuring the Network Management Interface” on page 43 for
configuration instructions.
For more information about the internal user interfaces, see the InfraStruXure Power
Distribution Unit online Network Management User’s Guide.
See also
The SNMP interface allows you to use an SNMP browser with the PowerNet® Management
Information Base (MIB) to manage the InfraStruXure PDU. See “Configuring the Network
Management Interface” on page 43 for configuration instructions.
See also
To use the PowerNet MIB with an SNMP browser, see the PowerNet® SNMP
Management Information Base (MIB) Reference Guide, which is provided on the
InfraStruXure Power Distribution Unit.
40kW InfraStruXure PDU—Operation and Configuration
41
Configuring the InfraStruXure Manager
Connect the PDU to the InfraStruXure Manager
1. Connect a Cat-5 network cable to the ethernet port on the PDU user connection plate.
You can make connections from
inside the enclosure, or you can
remove the user connection plate
and make your connections.
Remove the plate using a Phillips
or standard screwdriver to loosen
the two captive screws. Use the
knockout in the plate to route
cables to and from the user
connections on the plate. If you
remove the plate, make sure that
you do not disturb the existing connections.
2. Run the connected Cat-5 network cable through the knockout in the user connection plate to the
InfraStruXure Manager Hub.
3. Once all APC InfraStruXure-Certified equipment is installed, the network cables are connected
to the InfraStruXure Manager Hub, and start-up of the system is complete, configure the
InfraStruXure Manager.
For detailed configuration instructions, see the InfraStruXure Manager Installation and
Quick-Start manual included with your InfraStruXure Manager.
See also
42
40kW InfraStruXure PDU—Operation and Configuration
Configuring the Network Management
Interface
Disregard the procedures in this section if you have APC InfraStruXure Manager
as part of your system.
Warning
Connect the PDU to your network
1. Connect a Cat-5 network cable to the ethernet port on the PDU user connection plate.
You can make connections from
inside the enclosure, or you can
remove the user connection plate
and make your connections.
Remove the plate using a Phillips
or standard screw driver to loosen
the two captive screws. Use the
knockout in the plate to route
cables to and from the user
connections on the plate. If you
remove the plate, make sure that you do not disturb the existing connections.
2. Run the connected Cat-5 network cable through the knockout in the user connection plate to
your network connection.
3. Configure the TCP/IP settings of the PDU. See “Configuration Overview” on page 44 for
further instructions.
40kW InfraStruXure PDU—Operation and Configuration
43
Communication Configuration
Configuration Overview
You must configure the following TCP/IP settings before the PDU can operate on a network:
• IP address of the PDU
• Subnet mask
• Default gateway
Note
If a default gateway is unavailable, use the IP address of a computer that is located
on the same subnet as the PDU and that is usually running. The PDU uses the
default gateway to test the network when traffic is very light. See “Watchdog
Features” in the “Introduction” of the InfraStruXure Power Distribution Unit’s
online Network Management User’s Guide for more information about the
watchdog role of the default gateway.
TCP/IP configuration methods
Use one of the following methods to define the TCP/IP settings needed by the PDU:
• Device IP Configuration Wizard (See “Device IP Configuration Wizard” on page 44.)
• BOOTP or DHCP server (See “BOOTP & DHCP configuration” on page 45.)
• Local computer (See “Local access to the control console” on page 47.)
• Networked computer (See “Remote access to the control console” on page 47.)
Device IP Configuration Wizard
You can use the Device IP Configuration Wizard on a Windows NT® 4.0, Windows 2000, or
Windows XP computer to discover unconfigured InfraStruXure PDUs and configure their basic
TCP/IP settings.
To configure one or more PDUs by exporting configuration settings from a configured
PDU, see “How to Export Configuration Settings” in the online Network Management
See also User’s Guide on the Utility CD.
1. Insert the InfraStruXure Power Distribution Unit Utility CD into a computer on your network.
2. Launch the Wizard when prompted, or, if prompted to restart the computer, access the Wizard
from the Start menu after the computer has restarted.
3. Wait for the Wizard to discover the first unconfigured PDU, then follow the on-screen
instructions.
If you leave the Start a Web browser when finished option enabled, you can use apc
for both the User Name and Password to access the PDU through your browser.
Note
44
40kW InfraStruXure PDU—Operation and Configuration
Communication Configuration
BOOTP & DHCP configuration
The Boot Mode Setting, a TCP/IP option in the PDU’s Network menu, identifies how the TCP/IP
settings will be defined. The possible settings are Manual, DHCP only, BOOTP only, and DHCP &
BOOTP (the default setting).
Note
The DHCP & BOOTP setting assumes that a properly configured DHCP or BOOTP
server is available to provide TCP/IP settings to PDUs. If these servers are unavailable,
see “Device IP Configuration Wizard” on page 44, “Local access to the control console”
on page 47, or “Remote access to the control console” on page 47 to configure the
needed TCP/IP settings.
With Boot Mode set to DHCP & BOOTP, the PDU attempts to discover a properly configured server.
It first searches for a BOOTP server, then a DHCP server, and repeats this pattern until it discovers a
BOOTP or DHCP server.
For more information, see “BOOTP” on page 45 or “DHCP” on page 46.
Note
BOOTP. You can use an RFC951-compliant BOOTP server to configure the TCP/IP settings for the
PDU.
Note
The BOOTP setting assumes that a properly configured BOOTP server is available to
provide TCP/IP settings to APC PDUs. If a BOOTP server is unavailable, see “Device
IP Configuration Wizard” on page 44, “Local access to the control console” on page 47,
or “Remote access to the control console” on page 47 to configure the TCP/IP settings.
1. Make sure that the BOOTP setting, a TCP/IP option in the PDU’s Network menu, is enabled.
2. Enter the PDU’s MAC and IP addresses, the subnet mask and default gateway settings, and an
optional Bootup file name in the BOOTPTAB file of the BOOTP server.
For the MAC address, look on the Quality Assurance slip included with the PDU.
See also
3. When the PDU reboots, the BOOTP server provides it with the TCP/IP settings.
– If you specified a bootup file name, the PDU attempts to transfer that file from the BOOTP
server using TFTP or FTP. The PDU assumes all settings specified in the bootup file.
– If you did not specify a bootup file name, the PDU can be configured remotely by using
Telnet or by using the Web interface: User Name and Password are both apc, by default.
To create the bootup file, see your BOOTP server documentation.
See also
40kW InfraStruXure PDU—Operation and Configuration
45
Communication Configuration
DHCP. You can use a RFC2131/RFC2132-compliant DHCP server to configure the TCP/IP settings
for the PDU.
See also
This section briefly summarizes the PDU communication with a DHCP server. For
more detail about how a DHCP server is used to configure the network settings for a
PDU, see “DHCP Configuration” in the InfraStruXure Power Distribution Unit’s
online Network Management User’s Guide.
1. An InfraStruXure PDU sends out a DHCP request that uses the following to identify itself:
– A Vendor Class Identifier (APC by default)
– A Client Identifier (by default, the PDU’s MAC address value)
– A User Class Identifier (by default, the identification of the PDU’s application firmware)
2. A properly configured DHCP server responds with a DHCP offer that includes all of the
settings that the PDU needs for network communication. The DHCP offer also includes the
Vendor Specific Information option (DHCP option 43). By default, the PDU will ignore DHCP
offers that do not encapsulate the APC cookie in the Vendor Specific Information option using
the following hexidecimal format:
Option 43 = 01 04 31 41 50 43
where
– the first byte (01) is the code
– the second byte (04) is the length
– the remaining bytes (31 41 50 43) are the APC cookies
See your DHCP server documentation to add code to the Vendor Specific Information
option. To disable the APC cookie requirement, see “Local access to the control
console” on page 47.
To change the control console’s DHCP Cookie Is setting, use the Advanced option in
the TCP/IP menu. See “Remote access to the control console” on page 47.
46
40kW InfraStruXure PDU—Operation and Configuration
Communication Configuration
Local access to the control console
You can use a local computer that connects to the PDU through the console port on the PDU
monitoring unit to access the control console.
1. Select a serial port at the local computer, and disable any service that uses that port.
2. Use the configuration cable (APC part number 940-0103) to connect the selected port to the
console port on the PDU monitoring unit.
3. Run a terminal program (such as HyperTerminal®) on your computer and configure the selected
port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control, and save the changes.
4. Press ENTER to display the User Name prompt.
5. Use apc for the User Name and Password.
6. See “Control console” on page 48 to finish the configuration.
Remote access to the control console
From any computer on the same subnet as the PDU, you can use ARP and Ping to assign an IP
address to an InfraStruXure PDU, and then use Telnet to access that PDU’s control console and
configure the needed TCP/IP settings.
After an InfraStruXure PDU has its IP address configured, you can use Telnet, without
first using ARP and Ping, to access that PDU.
Note
1. Use ARP to define an IP address for the PDU, and use the PDU’s MAC address in the ARP
command. For example, to define an IP address of 156.205.14.141 for an InfraStruXure PDU
that has a MAC address of 00 c0 b7 63 9f 67, use one of the following commands:
– Windows command format:
arp -s 156.205.14.141 00-c0-b7-63-9f-67
– LINUX command format:
arp -s 156.205.14.141 00:c0:b7:63:9f:67
For the MAC address, look on the Quality Assurance slip included with the
PDU.
See also
2. Use Ping with a size of 113 bytes to assign the IP address defined by the ARP command. For the
IP address defined in step 1, use one of the following Ping commands:
– Windows command format:
ping 156.205.14.141 -l 113
– LINUX command format:
ping 156.205.14.141 -s 113
40kW InfraStruXure PDU—Operation and Configuration
47
Communication Configuration
3. Use Telnet to access the PDU at its newly assigned IP address. For example:
telnet 156.205.14.141
4. Use apc for both User Name and Password.
5. See “Control console” on this page to finish the configuration.
Control console
After you log on at the control console, as described in “Local access to the control console” on
page 47 or “Remote access to the control console” on page 47:
1. Choose Network from the Control Console menu.
2. Choose TCP/IP from the Network menu.
3. If you are not using a BOOTP or DHCP server to configure the
TCP/IP settings, select the Boot Mode menu. Select Manual boot mode, and then press ESC to
return to the TCP/IP menu. (Changes will take effect when you log out.)
4. Set the System IP, Subnet Mask, and Default Gateway address values.
5. Press CTRL-C to exit to the Control Console menu.
6. Log out (option 4 in the Control Console menu).
If you disconnected a cable during the procedure described in “Local access to the
control console” on page 47, reconnect that cable and restart the associated service.
Note
48
40kW InfraStruXure PDU—Operation and Configuration
How to Access a Network Management
Interface on a Configured PDU
Note
Disregard the procedures in this section if you have the APC InfraStruXure
Manager as part of your system. See the InfraStruXure Manager’s Installation
and Quick-Start manual for access information.
Web interface
As your browser, you can use Microsoft® Internet Explorer 5.0 (and higher) or Netscape® 4.0.8 (and
higher, except Netscape 6.x) to access the PDU through its Web interface. Other commonly available
browsers may also work but have not been fully tested by APC.
To use the Web browser to configure PDU options or to view the event log, you can use either of the
following:
• The HTTP protocol (enabled by default), which provides authentication by user name and
password but no encryption.
• The more secure HTTPS protocol, which provides extra security through Secure Socket Layer
(SSL) and encrypts user names, passwords, and data being transmitted. It also provides
authentication of Network Management Cards by means of digital certificates.
To access the Web interface and configure the security of your device on the network:
1. Address the PDU by its IP address or DNS name (if configured).
2. Enter the user name and password (by default, apc and apc for an Administrator, or device and
apc for a Device Manager).
3. Select and configure the type of security you want. (This option is available only for
Administrators.)
See also
See the chapter entitled “Security” in the InfraStruXure Power Distribution Unit’s
online Network Management User’s Guide for information on choosing and
setting up your network security. Use the Web/SSL option of the Network menu
to enable or disable the HTTP or HTTPS protocols.
Telnet and SSH
You can access the control console through Telnet or Secure SHell (SSH), depending on which is
enabled. (An Administrator can enable these access methods through the Telnet/SSH option of the
Network menu.) By default, Telnet is enabled. Enabling SSH automatically disables Telnet.
40kW InfraStruXure PDU—Operation and Configuration
49
Communication Configuration
Telnet for basic access. Telnet provides the basic security of authentication by user name and
password, but not the high-security benefits of encryption. To use Telnet to access an PDU’s control
console from any computer on the same subnet:
1. At a command prompt, use the following command line, and press ENTER:
telnet address
As address, use the PDU’s IP address or DNS name (if configured).
2. Enter the user name and password (by default, apc and apc for an Administrator, or device and
apc for a Device Manager).
SSH for high-security access. If you use the high security of SSL for the Web interface, use
Secure SHell (SSH) for access to the control console. SSH encrypts user names, passwords, and
transmitted data.
The interface, user accounts, and user access rights are the same whether you access the control
console through SSH or Telnet, but to use SSH, you must first configure SSH and have an SSH client
program installed on your computer.
See the InfraStruXure Power Distribution Unit’s online Network Management User’s
Guide for more information on configuring and using SSH.
See also
SNMP
After you add the PowerNet MIB to a standard SNMP MIB browser, you can use that browser for
SNMP access to the PDU. The default read community name is public; the default read/write
community name is private.
Note
50
If you enable SSL and SSH for their high-security authentication and encryption,
disable SNMP. Allowing SNMP access to the PDU compromises the high security you
implement by choosing SSL and SSH. To disable SNMP, you must be an Administrator;
use the SNMP option of the Network menu.
40kW InfraStruXure PDU—Operation and Configuration
Communication Configuration
FTP and SCP
You can use FTP (enabled by default) or Secure CoPy (SCP) to transfer new firmware to the PDU, or
to access a copy of the PDU’s event logs. SCP provides the higher security of encrypted data
transmission and is enabled automatically when you enable SSH.
Note
If you enable SSL and SSH for their high-security authentication and encryption,
disable FTP. Allowing file transfer to the PDU through FTP compromises the high
security you implement by choosing SSL and SSH. To disable FTP, you must be an
Administrator; use the FTP Server option of the Network menu.
To access the PDU through FTP or SCP, the default user name and password are apc and apc for an
Administrator, or device and apc for a Device Manager. In the command line, use the IP address of
the unit.
See also
See the InfraStruXure Power Distribution Unit’s online Network Management User’s
Guide to use FTP or SCP to retrieve log files from the PDU or to transfer firmware files
to the PDU.
40kW InfraStruXure PDU—Operation and Configuration
51
How to Recover From a Lost Network
Management Interface Password
Note
Disregard the procedures in this section if you have the APC InfraStruXure
Manager as part of your system. See the InfraStruXure Manager’s Installation
and Quick-Start manual for information on recovering from a lost password.
1. Select a serial port at the local computer, and disable any service that uses that port.
2. Connect the serial cable (APC part number 940-0103) to the selected port on the computer and
to the console port on the PDU monitoring unit.
3. Run a terminal program (such as HyperTerminal®) on your computer and configure the selected
port as follows:
– 9600 bps
– 8 data bits
– no parity
– 1 stop bit
– no flow control
4. Press ENTER, repeatedly if necessary, to display the User Name prompt. If you are unable to
display the User Name prompt, verify the following:
– The serial port is not in use by another application.
– The terminal settings are correct as specified in step 3.
– The correct cable is being used as specified in step 2.
5. Press the Reset button on the PDU monitoring unit. The Status LED will flash alternately
orange and green. Press the Reset button on the PDU monitoring unit a second time
immediately while the LED is flashing to reset the user name and password to their defaults
temporarily.
6. Press ENTER as many times as necessary to redisplay the User Name prompt, then use the
default, apc, for the user name and password. (If you take longer than 30 seconds to log on after
the User Name prompt is redisplayed, you must repeat step 5 and log on again.)
7. From the Control Console menu, select System, then User Manager.
8. Select Administrator, and change the User Name and Password settings, both of which are
now defined as apc.
9. Press CTRL-C, log off, reconnect any serial cable you disconnected, and restart any service you
disabled.
52
40kW InfraStruXure PDU—Operation and Configuration
Customizing and Updating the PDU
Important Safety Instructions
Electrical
Hazard
APC does not recommend that you perform maintenance of the PDU while it is
receiving input power. However, due to the critical nature of data center loads, this
may occur. If you must perform maintenance while the PDU is receiving input
power, observe the following precautions to reduce the risk of electric shock:
1. Never work alone.
2. Perform the maintenance only if you are a certified electrician who is trained
in the hazards of live electrical installation.
3. Know the procedure for disconnecting electricity to the PDU and the data
center in case of an emergency.
4. Wear appropriate personal protective equipment.
5. Use double-insulated tools.
6. Always follow local and site regulations when working on the PDU.
40kW InfraStruXure PDU—Operation and Configuration
53
PDU Orderable Part List
Circuit Breakers
0M-1293
10A, single-pole breaker
0M-1706 32A with 100mA ELCB, three-pole breaker
0M-1304
16A, single-pole breaker
0M-1707 32A with 30mA ELCB, three-pole breaker
0M-1703
16A with 30mA ELCB, two-pole breaker
0M-1708 16A with 100mA ELCB, three-pole breaker
0M-1704
10A with 30mA ELCB, single-pole breaker
0M-1709 10A with 100mA ELCB, three-pole breaker
0M-1705
32A, single-pole breaker
Power Cables
PDW15EC309R
PDW100EC309R
PDW21EC309R
PDW107EC309R
PDW27EC309R
PDW113EC309R
PDW33EC309R
PDW119EC309R
PDW40EC309R
PDW125EC309R
PDW46EC309R
PDW131EC309R
PDW52EC309R
PDW137EC309R
PDW58EC309R
PDW143EC309R
PDW64EC309R
PDW149EC309R
PDW70EC309R
PDW155EC309R
PDW76EC309R
PDW161EC309R
PDW82EC309R
PDW167EC309R
PDW88EC309R
PDW173EC309R
PDW94EC309R
PDW180EC309R
54
40kW InfraStruXure PDU—Operation and Configuration
How to Add Circuit Breakers and Power
Cables
Add a circuit breaker on the PDU
1. Move the clip on the back of
the breaker to correspond to
the phase to which you are
connecting to (L1, L2, or L3).
2. Snap the new single-pole
circuit breaker into position
on the panel.
3. Remove the corresponding
plastic blanking plate on the
front panel of the PDU.
Add a power cable to the PDU
Before adding a power cable, add a circuit breaker.
1. Install a strain-relief connect in
any available knockout on the roof
of the PDU.
2. Slide enough of the power cable
through the strain-relief connector
to reach the new circuit breaker.
3. Tighten the strain-relief connector.
40kW InfraStruXure PDU—Operation and Configuration
55
Customizing and Updating the PDU
4. At the front of the PDU, connect the power cord’s individual wires:
a. If you have branch current monitoring installed, route the phase conductor through a current
sensor.
b. Connect the line wire to the circuit breaker.
c. Connect the neutral wire to the closest open termination point on the Neutral Bar (N).
d. Connect the PE wire to the closest open termination point on the PE Bar (PE).
N
PE
56
40kW InfraStruXure PDU—Operation and Configuration
How to Connect User Input Contacts and
Relay Outputs to the PDU User Connection
Plate
Overview
4
Contact Outputs
ATS 1
2
3
Contact Inputs
ATS 2
1
ATS 0
USER INTERFACE
© 2001 APC
MADE IN USA
ATS EN
Make contact closure connections
(NO or NC) at the user connection
plate to monitor dry contacts. You can
make eight connections—four input
contacts and four relay outputs.
– +
EPO 24V EPO
AC/DC Contact
The figure at the right shows the
location of the user connection plate
on the roof of the PDU enclosure.
You can make connections from inside
the enclosure, or you can remove the
user connection plate and make your
connections.
Remove the plate using a Phillips or
standard screwdriver to loosen the two
captive screws. Use the knockout in
the plate to route cables to and from
the user connection on the plate. If you
remove the plate, make sure that you
do not disturb the existing
connections.
40kW InfraStruXure PDU—Operation and Configuration
57
Customizing and Updating the PDU
How to connect contacts to the PDU monitoring unit
1. Choose one or more contact number(s) on the User/EPO contacts port on the user connection
plate to which you will connect the contacts. The user connection plate connects to the PDU
monitoring unit.
2. From the PDU display interface:
a. Press the ESC or ENTER key to go to the top-level menu screen.
b. Select Contacts on the top-level menu screen, and press the ENTER key.
Load-Meter
Volt-Meter
Contacts
Breakers
Alarms
Panel
Config
Help
c. Select Contact Inputs (or Relay Outputs) and press ENTER to display the contact inputs (or
relay outputs) screen.
>Contact Inputs
>Relay Outputs
>Alarm Relay Map
d. Select Contact In and press the ENTER key to select the number of the contact you are
connecting. The continue arrow will appear next to the contact number.
Contact In:01of04
Name: User Contact1
Normal:Open
Status: Closed
e. Press the Up or Down arrow key to select the appropriate contact number, and press the
ENTER key.
f. Press the Down arrow key to enter a unique Name for the contact and to configure the
Normal state of the contact (Open or Closed). The default Normal state is Open. Press the
ENTER key to select the item to configure.
You will be prompted for your password to configure these items.
Note
3. Connect contact wires (300V-rated cabling required) to the User Contacts terminal block on
the user connection plate. You will need a 2.5-mm standard screwdriver.
4. Run the wires from the terminal block out the roof or under the floor of the PDU to your
contact’s location.
Ensure that wires are properly retained and away from high voltage lines and
breakers.
Warning
See “Relay Outputs” on page 66 for relay output specifications.
58
40kW InfraStruXure PDU—Operation and Configuration
How to Test the Emergency Power Off
Switch
APC offers an optional InfraStruXure EPO System (EPW9). Contact your APC sales
representative, or visit the APC Web site (www.apc.com) for more information.
Note
If you are not connecting an Emergency Power Off switch to the PDU, leave the
Arm/Test rocker switch on the PDU monitoring unit to the Test position.
Caution
Overview
Connecting the switch. The Emergency
4
Contact Outputs
ATS 1
2
3
Contact Inputs
ATS 2
1
ATS 0
USER INTERFACE
© 2001 APC
MADE IN USA
ATS EN
Power Off (EPO) switch connects to the
PDU user connection plate. The figure on the
right shows the location of the user
connection plate on the roof of the PDU.
Connect a switch using one of three
following connections:
– +
EPO 24V EPO
AC/DC Contact
• Contact closure
• 24VAC
• 24VDC
Contact closure is recommended.
Note
40kW InfraStruXure PDU—Operation and Configuration
59
Customizing and Updating the PDU
Configuring and testing. Configuring and testing of the switch is
done through the EPO interface on the PDU monitoring unit. The figure
to the right shows the PDU monitoring unit and the location of the EPO
LEDs and DIP switches.
TRIPPED
19
6
18
5
17
4
16
3
15
2
14
TO UPS
8
20
7
TEST
10
22
9
21
EPO
ARMED
1
USE R / EPO C ONTACTS
885 -22 88
23
11
24
12
25
POWER
TRIPPED
DISPLAY
STATUS
13
10=G RN
100= ORN
N ETWOR K
RE SE T
NO
NC
LINK R X/TX
9600-8-N -1
NO
R S-232
CON SOLE POR T
TEST
NC
EPO
AR ME D
Testing the switch
Normally Closed
1. Before testing the EPO switch, verify that the EPO DIP switches on the PDU monitoring unit
are configured properly for the signal type you are using. The labels above the switches and the
figure below show the correct settings for both the Normally Open (NO) and Normally Closed
(NC) position.
TRIPPED
Location of switches
on PDU monitoring unit
NC
TEST
NO
Normally Open
or 24V AC/DC
EPO
ARMED
The default setting on the EPO interface on the PDU monitoring unit is for a Normally
Open (NO) switch.
Note
60
40kW InfraStruXure PDU—Operation and Configuration
Customizing and Updating the PDU
2. Test the EPO switch to ensure that it is wired and working correctly:
a. Place the Arm/Test rocker switch in the Test position. The EPO state LEDs will be off and
the PDU display interface will show the following alarm (in addition to any other active
alarms):
Active Alarm xxofxx
EPO Ready To Test
b. Engage the EPO switch. (If your switch is momentary, engage it with one person watching
the EPO state LEDs, and another at the EPO switch.)
c. Observe the EPO LEDs. If the switch is wired and working properly, when the switch is
engaged, both of the EPO state LEDs are red.
d. If the test was successful, place the Arm/Test rocker switch back to the Arm position. The
PDU display interface will clear the EPO test mode alarm. If the test was not successful, see
the troubleshooting chart:
Problem
Action
Neither state LED was red when
EPO switch was engaged
• Check the wiring to your EPO switch.
Only one of the state LEDs was
red when EPO switch was
engaged
• Check to make sure the EPO DIP switch
configuration is correct for your switch
(NO or NC) and test again. See step 1 on the
previous page for proper configuration
instructions.
• Check to make sure the EPO DIP switch
configuration is correct for your switch
(NO or NC). See step 1 on the previous page for
proper configuration instructions.
• If the switch is configured correctly and both
LEDs are not red after testing again, contact
customer support at a number on the back cover
of this manual.
e. Repeat this test for each EPO switch installed.
3. Ensure that the Arm/Test rocker switch is in the Arm position on the monitoring unit.
40kW InfraStruXure PDU—Operation and Configuration
61
Customizing and Updating the PDU
Safety warnings
This InfraStruXure PDU and Symmetra PX UPS are provided with an Emergency Power Off switch
connection. When this EPO switch is energized, electrical power to the units is de-energized and the
system will not transfer to on-battery operation.
EPO can be achieved with either a contact closure or application of an external 24 VAC or 24 VDC
from a SELV or PELV source. It is important to note that hazardous voltage from the Mains voltage
must be isolated from the contact closure or 24 VAC, 24 VDC. The EPO circuit contact closure, the
24 VAC, or the 24 VDC is considered a SELV circuit as defined in EN 60950 Safety of Information
Technology Equipment or PELV circuit as defined in IEC 60364-4-41 Electrical Installations of
Buildings, Protection for Safety—Protection Against Electric Shock. SELV is an abbreviation for
Safety Extra Low Voltage. PELV is an abbreviation for Protective Extra Low Voltage. SELV and
PELV circuits are isolated from the Mains through a safety isolating transformer, and are designed so
that under normal conditions the voltage is limited to 42.4 Vpeak or 60 VDC.
62
40kW InfraStruXure PDU—Operation and Configuration
How to Download Firmware Upgrades
Upgrading the PDU monitor processor
You can download available PDU monitor processor upgrades through the PDU display interface.
The most obvious indication that a firmware upgrade is necessary occurs when the Network
Management Card and monitor processor stop communicating. This lack of communication causes
the PDU’s data to no longer be accessible through the display interface and a SysData Mismatch
alarm to occur. When this alarm occurs, perform the following steps to upgrade the PDU monitor
processor firmware.
1. Upgrade the PDU Network Management Card.
See also
For instructions on how to upgrade the PDU’s Network Management Card,
refer to the online Network Management User’s Guide on the Utility CD
provided with your InfraStruXure PDU.
2. At the PDU display interface, select Config, and then Firmware Updates. You will receive the
following screen:
Press any key to download the update.
Note
If you do not receive the SysData Mismatch alarm, but want to check for
available firmware upgrades, you can do so by performing step 2 in the
procedure above.
From a local computer
To download a firmware upgrade and transfer it to your PDU, see “File Transfers” in the
InfraStruXure PDU’s online Network Management User’s Guide on the Utility CD.
See also
1. Select a serial port at the local computer, and disable any service that uses that port.
2. Use the configuration cable to connect the selected port to the console port on the PDU
monitoring unit.
3. Run a terminal program (such as HyperTerminal®) and configure the selected port for 9600 bps,
8 data bits, no parity, 1 stop bit, and no flow control. Save the changes.
4. Press ENTER twice to display the User Name prompt.
5. Enter your User Name and Password (both apc, for administrators only) and press the ENTER
key.
40kW InfraStruXure PDU—Operation and Configuration
63
Customizing and Updating the PDU
6. From the Control Console menu, select System, then Tools, then File Transfer, then
XMODEM.
7. The system will prompt you with Perform transfer with XMODEM –CRC? Type Yes
and press ENTER.
8. The system will then prompt you to choose a transfer rate and to change your terminal settings
to match the transfer rate. Press ENTER to set the PDU to accept the download.
9. In the terminal program, send the file using XMODEM protocol. Upon completion of the
transfer, the console will prompt you to restore the baud rate to normal.
Do not interrupt the download.
Caution
The PDU network management interface will reboot when the download is complete.
64
40kW InfraStruXure PDU—Operation and Configuration
Specifications
40kW InfraStruXure PDU
Electrical
Output
Nominal Output Voltage AC
3 × 400/230V
Frequency
50 or 60Hz
Nominal Output Current
111A
Maximum Continuous Output Current
(+ 125% Overload)
139A (Bypass mode only)
Grounding
Separately derived neutral/ground bond
Full Load Output Rating
40 kW
External Output Breaker
150A
Transformer (if installed)
Type
Isolation
Configuration
Dy
Maximum Power Rating
60kVa
Maximum Current Rating
87A
Construction
Cu windings, open core
Efficiency
98%
Input
Voltages
Transformer: 3 × 400V; No Transformer 3 × 400/230V
Nominal Input Voltage AC
3 × 400V
Frequency
50 or 60Hz
Nominal Input Current
65.7A
Maximum Continuous Input Current
155A at minimum mains
Grounding
PE node (from AC feed or floor grid)
Conductors to Main Input Switch
Transformer: L1, L2, L3, + PE ;
No Transformer: L1, L2, L3, N + PE
Wiring
Main Input Power Feed
Top or bottom entry
PDU to UPS wiring
L1, L2, L3, N+ PE
UPS to PDU wiring
L1, L2, L3, N
PDU to Distribution Panels
L1, L2, L3, N+PE (1/0awg)
Distribution Panels to Racks/Power Strips
L1, L2, L3, N+ PE (12awg)
40kW InfraStruXure PDU—Operation and Configuration
65
Specifications
Electrical
Cable Connections
IEC 309, 16A
Cable Lengths
Various, determined by CTO
Power Cable Wiring—top
Accommodates 28, 3-phase power cables (42 knock-outs)
Power Cable Wiring—bottom
Accommodates 28, 3-phase power cables (48 knock-outs)
Panel Boards
Panel Style
3-phase
Number of Panels (per PDU)
2 maximum
Positions per Panel
42, double row
Breakers per Panel
42
1-phase breakers per panel
42 maximum
Panel rating
240V/ 225A per phase
Breaker Pitch
19mm
Accessibility
Through front of unit
Over-current Protection
Main Input Breaker
125A
UPS Input Breaker
125A
Maintenance Breaker
100A
UPS Output Breaker
100A
Distribution Breakers
1-pole or 3-pole with or without ELCB, 10A, 16A, and 32A
Relay Outputs
Nominal Switching Capacity
1A at 30VDC
Maximum Switching Power
30W
Maximum Switching Voltage
60VDC
Maximum Switching Current
2ADC
Maximum Carrying Current
2ADC
Surge Ratings
2kV per Bellcore TA-NWT-001089
1.5kV per FCC part 68
Physical
Dimensions (H×W×D)
PDU
2070 × 597 × 902 mm (81 × 24 × 36in)
Shipping
2184 × 914 × 1219 mm (86 × 36 × 48in)
Shielding Trough
191 × 579 × 323 mm (7.5 × 23 × 13in)
Weight
66
PDU with Transformer
844kg (1861lb)
PDU without Transformer
590kg (1301lb)
Shipping with Transformer
867kg (1911lb)
Shipping without Transformer
613kg (1351lb)
40kW InfraStruXure PDU—Operation and Configuration
Specifications
Physical
Service Access
Front and rear
Service Clearance
Greater than or equal to 914mm
Environmental
Operating Environment
Indoor use only, protected from water and conductive
contaminates
Temperature
Operating
0 to 40°C
Storage
0 to 45°C
Class
Class H (220°C)
Humidity
Operating
0–95%, non-condensing
Storage
0–95%, non-condensing
Elevation
Storage
10 000 m (for aircraft transportation)
Acoustic Noise Emission
Maximum 50dB(A) at 1 m
Heat Dissipation
1.7kW (with transformer)
Compliance
Approvals
CE, EN, TUV
40kW InfraStruXure PDU—Operation and Configuration
67
Product Information
InfraStruXure Standard Warranty
APC warrants that all components of the InfraStruXure system will be free from defect in material
and workmanship for a period of two years from the date of start up when start up has been
performed by APC authorized service personnel*. If assembly services are included in the original
purchase and are also performed by APC authorized service personnel, APC offers an additional year
of parts warranty and the first year of on site coverage at no additional charge. In the event that the
system fails to meet the forgoing warranty, APC shall repair or replace, at its sole discretion, any such
defective parts. Under this warranty, APC will ship all parts to your site at no cost to be available for
you the next business day after APC is notified of this requirement. If you choose to upgrade the
system to include an on site contract, APC offers modular service packages to match your needs.
Each point product incorporated into the system has a separate factory warranty that is applied when
sold as a standalone unit. When incorporated into an InfraStruXure solution, the unit will be covered
by the InfraStruXure warranty. In cases where one warranty favors the customer over the other, the
stronger of the two warranties will take precedence. The InfraStruXure factory warranty covers only
those parts appearing on the bill of materials for that solution. Megawatt UPS systems are not
covered under the InfraStruXure factory warranty.
Battery functionality is typically impacted by age and environmental conditions, and therefore certain
requirements must be met by the end-user. Failure to adhere to these requirements may put the battery
warranty at risk. APC-supplied batteries must always be kept (whether stored or installed) in a
climate-controlled environment, and should be re-charged at a minimum of every three (3) months.
The battery environment must be free of excessive moisture, construction dirt, corrosive elements, or
other contaminants. The temperature range must be maintained at 41 to 95° F (5 to 35° C).
*All warranties are null and void unless startup is performed by authorized an APC Global Services
service center.
APC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY PURCHASER'S OR ANY THIRD PERSON'S MISUSE,
NEGLIGENCE, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED
ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR
OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS
AGREEMENT OR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A
40kW InfraStruXure PDU—Operation and Configuration
69
Product Information
PARTICULAR PURPOSE. APC'S EXPRESS WARRANTIES WILL NOT BE ENLARGED,
DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE
OUT OF, APC'S RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN
CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND
REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND
REMEDIES. THE WARRANTIES SET FORTH ABOVE. CONSTITUTE APC'S SOLE
LIABILITY AND PURCHASER' EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH
WARRANTIES. APC'S WARRANTIES RUN ONLY TO PURCHASER AND ARE NOT
EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR
EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE
OR INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN
CONTRACT OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT
LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE
POSSIBILITY OF SUCH DAMAGES.
70
40kW InfraStruXure PDU—Operation and Configuration
Life-Support Policy
APC Three-Phase Systems
American Power Conversion Corporation (APC) and its affiliates and subsidiaries worldwide do not
recommend the use of any of their products in life-support applications where failure or malfunction
of the APC product can be reasonably expected to cause failure of the life-support device or to
significantly affect its safety or effectiveness. APC does not permit the use of any of its products in
direct patient care. APC will not knowingly sell its products for use in such applications unless the
life-support system or direct patient care device is part of a whole facility/building into which the
UPS is integrated, and unless APC receives, in writing, assurances satisfactory to APC that:
a. The UPS system will be configured in a manner that will provide N+1 power redundancy to
the critical load,
b. The end-user customer assumes all risks and signs the APC System Configuration and Use
Form, and
c. The customer and operators of the APC UPS system agree to indemnify and hold APC and
its affiliates and subsidiaries harmless for any and all claims arising out of the systems use in
such applications.
The term life-support device includes but is not limited to neonatal oxygen analyzers, nerve
stimulators (whether used for anesthesia, pain relief, or other purposes), autotransfusion devices,
blood pumps, defibrillators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems,
peritoneal dialysis systems, neonatal ventilator incubators, ventilators (for adults and infants),
anesthesia ventilators, infusion pumps, and any other devices designated as “critical” by the U.S. FDA.
Hospital-grade wiring devices and leakage current protection may be ordered as options on many
APC UPS systems. APC does not claim that units with these modifications are certified or listed as
hospital-grade by APC or any other organization. Therefore these units do not meet the requirements
for use in direct patient care.
40kW InfraStruXure PDU—Operation and Configuration
71
How to Obtain Service
Note
If you ordered on-site service, see your entitlement certificate and the terms and
conditions of the service before following the procedure described below. An on-site
service contract entitles you to an on-site visit by an APC technician to assess the issue,
determine the problem, and replace parts, if needed. (Response time varies per contract.)
How to contact APC
Customer support for this or any other APC product is available at no charge in any of the following
ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit
customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
– Regional centers:
Direct InfraStruXure Customer Support Line
(1) (877) 537-0607 (toll free)
APC Headquarters U.S., Canada
(1) (800) 800-4272 (toll free)
Latin America
(1) (401) 789-5735 (USA)
Europe, Middle East, Africa
(353) (91) 702000 (Ireland)
Japan
(0) 3 5434-2021
Australia, New Zealand, South Pacific area
(61) (2) 9955 9366 (Australia)
– Local, country-specific centers: go to www.apc.com/support/contact for contact
information.
Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.
72
40kW InfraStruXure PDU—Operation and Configuration
Appendix A: Changes in This Manual
Overview
The following list references the specific changes made to this manual since its last release (9901597A).
General changes
• Communication configuration instructions were added. See pages 43–52.
• Maintenance chapter was expanded and renamed as “Customizing and Updating the PDU.”
Changes by page number
Page 9
Added detailed description of the user connection plate.
Page 41
Added “InfraStruXure PDU Management Options.”
Page 42
Added “Configuring the InfraStruXure Manager.”
Pages 43–52
Added “Configuring the Network Management Interface.”
Pages 49–51
Added “How to Access a Network Management Interface on a
Configured PDU.”
Page 52
Added “How to Recover from a Lost Network Management Interface
Password.”
Pages 57–58
Added “How to Connect User Input Contacts and Relay Outputs to
the PDU User Connection Plate.”
Pages 59–60
Added How to Connect an EPO Switch to the PDU and Test the
Switch.”
Page 63
Added “How to Download Firmware.”
40kW InfraStruXure PDU—Operation and Configuration
73
Index
A
Agency approvals, 67
Alarm beeper, 21
Alarm LED, location of, 11
Alarm relay map, 17
Alarm setup, 21
Alarm types. See entry of specific
alarm.
Alarm/event log, 20
Alarms screen, 20 – 22
Arm/test rocker switch on PDU
monitoring unit, 8
Armed LED on PDU monitoring
unit, 8
B
BOOTP configuration, 45
Branch current monitor ports on
PDU monitoring unit, 8
Breakers screen, 19
Bypass LED, location of, 11
C
Cables
access holes, location of, 5
adding to the PDU, 55 – 56
input and output, location of, 7
location of, 5
Caution symbol, 1
Check log LED, location of, 11
Circuit breaker panels, location
of, 6
Circuit breakers
adding to the PDU, 55
orderable options, 54
Q1, location of, 6
Q2, location of, 6
Q3, location of, 6
Config screen, 26 – 28
Configuration
BOOTP, 45
DHCP, 45 – 46
electrical, 27
factory defaults, 28
firmware updates, 28
load test port, 27
manufacturer data, 28
max. power, 27
network address, 26
of communication devices, 41 –
52
of date/time, 26
of global panel, 25
of input, 27
of local interface, 26
of output, 27
of panel, 24
of the EPO switch, 59
product data, 28
TCP/IP, 44
Console port on PDU monitoring
unit, 8
Contacts screen, 16 – 58
Control console
for PDU management, 41
local and remote access to, 47 –
48
Current over limit alarm, 22
Current under limit alarm, 22
Customizing the PDU, 53
adding circuit breakers and
power cables, 55 – 56
orderable part list, 54
D
DC disconnect circuit breaker, 31 –
32, 35 – 36, 38
DHCP configuration, 45 – 46
Dimensions, of InfraStruXure
PDU, 66
DIP switches on PDU monitoring
unit, 8
Display interface
location of, 5
overview, 11
screens, 12 – 28
alarms, 20 – 22
breakers, 19
config, 26 – 28
contacts, 16 – 58
load-meter, 14
navigating through, 12
panel, 23 – 25
password-protected, 13
top-level menu, 12
top-level status, 12
volt-meter, 15
Display port on PDU monitoring
unit, 8
Document pocket, location of, 6
E
Electrical configuration, 27
Electrical hazard symbol, 1
Emergency Power Off (EPO)
configuring and testing, 59
connecting to the PDU, 59 – 62
problems with, 61
safety warnings, 3
EMI warnings, 3
Enter key, location of, 11
EPO contacts port on PDU
monitoring unit, 8
EPO. See Emergency Power Off
(EPO).
Esc key, location of, 11
F
Factory defaults, restoring, 28
Fan rotation failure alarm, 22
Firmware
downloading updates, 63
transferring through FTP or
SCP, 51
Frequency out of range alarm, 22
40kW InfraStruXure PDU—Operation and Configuration
75
FTP access to the PDU, 51
Fuses, location of, 7
IP configuration wizard, 44
K
H
Keys, navigation, location of, 11
H2 LED, 30, 34
H3 LED, 34
Heavy symbol, 1
Help key, location of, 11
L
I
InfraStruXure Manager
as a PDU management
option, 41
configuration, 42
InfraStruXure PDU
agency approvals, 67
alarm types, 22
components, 5
connecting to the network, 43
dimensions, 66
elevation, 66
heat dissipation, 67
humidity (operating and
storage), 66
monitoring unit
detailed description, 8
location of, 7
orderable parts, 54
service access and clearance, 66
specifications, 65 – 67
temperature (operating and
storage), 66
warranty, 69 – 70
weight, 66
Input
configuration of, 27
frequency, 65
nominal current, 65
nominal voltage AC, 65
voltage, where displayed, 15
voltages, 65
Input contacts
connecting, ??– 18, ??– 58
Input contacts, connecting to the
user connection plate, 57
Input power connection, PDU
monitoring unit, 8
Input transformer, location of, 7
76
LCD, location of, 11
LEDs. See invidual LED name.
Leveling feet, location of, 5
Life-support policy, 71
Load powered LED, location of, 11
Load test port configuration, 27
Load test port, location of, 7
Load-meter screen, 14
Local interface configuration, 26
M
Main breaker open alarm, 22
Main input switch, 7, 37
main input switch, 36
Maintenance
safety during, 53
Maintenance bypass operation
returning from, 32 – 34
transferring the UPS into, 29 –
31
Maintenance bypass panel, location
of, 6
Management options, 41 – 52
InfraStruXure Manager, 41
Network management
interfaces, 41
Max. power configuration, 27
Monitoring unit
connecting contacts to, 18, 58
N
Navigation keys, location of, 11
Network address configuration, 26
Network management interface
accessing on a configured
PDU, 49
configuration, 43 – 52
recovering from a lost
password, 52
Network port on PDU monitoring
unit, 8
Neutral bar, location of, 56
Neutral wire, location of, 56
No panel feed alarm, 22
No UPS input alarm, 22
Note symbol, 1
O
Operating environment, 66
Operation, 29 – 40
applying power to the
system, 37 – 40
returning from maintenance
bypass, 32 – 34
total power off, ensuring, 35 –
36
transferring the UPS into
maintenance bypass, 29 – 31
Output
configuration of, 27
frequency, 65
nominal current, 65
nominal voltage AC, 65
voltage, where displayed, 15
P
Panel configuration, 24
Panel screen, 23 – 25
Panels
1-phase breakers per, 66
accessibility, 66
breaker pitch, 66
breakers per, 66
number of, 66
positions per, 66
rating, 66
style, 66
Password
how to change, 26
Passwords
network management interface,
recovering from a lost
password, 52
PDU monitoring unit
detailed description, 8
location of, 7
PDU. See InfraStruXure PDU.
PE bar, location of, 56
PE wire, location of, 56
40kW InfraStruXure PDU—Operation and Configuration
Power LED on PDU monitoring
unit, 8
Q
Q1 circuit breaker, 6, 19, 31 – 32,
36 – 37
Q2 circuit breaker, 6, 19, 30, 34, 36,
40
Q3 circuit breaker, 6, 19, 30, 34, 36
R
Relay outputs
connecting to the user
connection plate, 57
Reset button on PDU monitoring
unit, 8
S
Safety, 1 – 3
overview, 1
symbols used in this manual, 1
warnings, 2 – 3
electric shock risk, 3
Emergency Power Off
(EPO), 3
EMI, 3
for maintenence while the
PDU is receiving input
power, 2
installation maintenance, 2
total power off, 3
safety
symbols used in this manual, 1
SCP access to the PDU, 51
Screens. See display interface or
individual screen name.
Service, how to obtain, 72
Shielding trough, location of, 5
SNMP access to the PDU, 50
SSH
for accessing a network
management interface, 49 – 50
Standby state, 1
System enable switch, 31, 35, 38
T
TCP/IP configuration options, 44
Telnet
for accessing a network
management interface, 49 – 50
Temperature, 66
Temperature too high alarm, 22
To UPS port on PDU monitoring
unit, 8
Top-level menu screen, 12
Top-level status screens, 12
Total Power Off
ensuring, 35 – 36
Total power off
warnings, 3
Tripped LED on PDU monitoring
unit, 8
Web interface
accessing a Network
management interface
through, 49
for PDU management, 41
Weight, of InfraStruXure PDU, 66
Wiring
cable connections, 66
cable lengths, 66
distribution panels to racks, 65
main input power feed, 65
PDU to distribution panels, 65
PDU to UPS, 65
power cable wiring, bottom, 66
power cable wiring, top, 66
UPS to PDU, 65
U
Updates
in this manual, 73
to firmware, 28, 63
to the PDU, 53
to this manual, i
User connection plate
detailed description, 9
User contacts port on PDU
monitoring unit, 8
V
Voltage
input, where displayed, 15
nominal input AC, 65
nominal output AC, 65
output, where displayed, 15
Voltage over limit alarm, 22
Voltage under limit alarm, 22
Volt-meter screen, 15
W
Warning symbol, 1
Warnings, 2 – 3
electric shock risk, 3
EMI, 3
for maintnenance while the PDU
is receiving input power, 2
installation/maintenance, 2
total power off, 3
Warranty, 69 – 70
40kW InfraStruXure PDU—Operation and Configuration
77
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer
support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
– Regional centers:
APC headquarters U.S., Canada
(1)(800)800-4272 (toll free)
InfraStruXure Technical Support
(1)(877)537-0607 (toll free)
Latin America
(1)(401)789-5735 (USA)
Europe, Middle East, Africa
(353)(91)702020 (Ireland)
Japan
(0) 35434-2021
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.
Entire contents © 2004 American Power Conversion. All rights reserved. Reproduction in whole or
in part without permission is prohibited. APC, the APC logo, InfraStruXure, NetShelter, and
Symmetra are trademarks of American Power Conversion Corporation and may be registered in
some jurisdictions. All other trademarks, product names, and corporate names are the property of
their respective owners and are used for informational purposes only.
990-1597B-001
*990-1597B-001*
12/2004
Download PDF

advertising