BKPF-L612 2-CH SDI DISTRIBUTION BOARD 警告

2-CH SDI DISTRIBUTION BOARD

BKPF-L612

警告

概要

電気製品は、安全のための注意事項を守らな

いと、火災や人身事故になることがあります。

• ご使用にあたっては、インターフェースユニットPFV-Lシリーズに

付属のオペレーションマニュアルの「安全のために」をよくお読

みください。

• 本機をあやまって装着すると、火災・感電やその他の事故によ

危険を避けるため、装着はサービストレーニングを受けた技術者

にご依頼ください。

本機を装着する技術者へ

装着のしかたは、PFV-Lシリーズに付属のマニュアルをご覧くださ

い。

るオプション基板です。2系統の入力信号をそれぞれ4分配して出

力します。入力信号は、540Mbps、360Mbps、270Mbps (4:2:2

SDI)、177Mbps (4fsc PAL SDI)、143Mbps (4fsc NTSC SDI)の5

つのフォーマットに対応しています。

仕様

電源

質量

+5 V DC、0.6 A（PFV-Lシリーズより供給）

最大外形寸法 メインボ−ド：77.2 × 267 mm（幅／長さ）

コネクタ−ボ−ド：32.6 × 85 mm（幅／長さ）

メインボ−ド：140 g

コネクタ−ボ−ド：100 g

仕様および外観は、改良のため予告なく変更することがあります

が、ご了承ください。

Precautions

If this board is installed incorrectly, personal injury or damage to peripheral items may occur due to fire, shock, or other accidental circumstances. To avoid such risks, installation should be performed by trained service technicians.

To technician installing board

Please refer to the Manual supplied with the PFV-Lseries unit for installation instructions.

Introduction

This product is an optional board designed to be installed in a PFV-L-series Interface Unit. The board accepts two input signals, each of which is divided into four and output. The unit conforms to five signal formats: 540 Mbps, 360 Mbps, 270 Mbps (4:2:2 SDI),

177 Mbps (4fsc PAL SDI), and 143 Mbps (4fsc

NTSC SDI).

Specifications

Power requirements +5 V DC, 0.6 A (supplied from the PFV-L-series unit)

Dimensions (w/l) Main board: 77.2

×

267 mm

(3 1/8

×

10 3/4 inches)

Connector borad: 32.6

×

85 mm

(1 5/16

×

3 3/8 inches)

Mass Main board: 140 g (5 oz)

Connector board: 100 g (4 oz)

Design and specifications are subject to change without notice.

INSTALLATION GUIDE

Sony Corporation

B & P Company

BKPF-L612 (SY 、和、英 )

3-866-904-02 (1)

Printed in Japan

2002.10.13



1999

For the customers in the USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of

FCC Rules.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accpet an interference received, including interference that may cause undesired operation.

For customer in Canada

This Class A digital apparatus complies with Canadian ICES-

003.

Pour les utilisateurs au Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Precaution

If this unit is installed incorrectly, personal injury or damage to peripheral items may occur due to fire, shock, or other accidental circumstances. To avoid such risks, installation should be performed by qualified service technicians.

To technician installing unit

For installation instructions, please refer to the manual supplied with the interface unit.

For the customers in Europe

This product with the CE marking complies with the EMC

Directive (89/336/EEC) issued by the Commission of the

European Community.

Compliance with this directive implies conformity to the following European standards:

• EN55103-1: Electromagnetic Interference (Emission)

• EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following

Electromagnetic Environment(s):

E1 (residential), E2 (commercial and light industrial), E3

(urban outdoors) and E4 (controlled EMC environment, ex.

TV studio)

Pour les clients européens

Ce produit portant la marque CE est conforme à la Directive sur la compatibilité électromagnétique (EMC) (89/336/CEE)

émise par la Commission de la Communauté Européenne.

La conformité à cette directive implique la conformité aux normes européennes suivantes:

• EN55103-1: Interférences électromagnétiques (émission)

• EN55103-2: Sensibilité électromagétique (immunité)

Ce produit est prévu pour être utillisé dans les environnements électromagnétiques suivants:

E1 (résidentiel), E2 (commercial et industrie légère), E3

(urbain extérieur) et E4 (environnement EMC contrôlé ex.

studio de télévision).

Für Kunden in Europa

Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die

EMV-Direktive (89/336/EEC) der EG-Kommission.

Die Erfüllung dieser Direktive bedeutet Konformität für die folgenden Europäischen Normen:

• EN55103-1: Elektromagnetische Interferenz (Emission)

• EN55103-2: Elektromagnetische Empfindichkeit

(Immunität) Dieses Produkt ist für den Einsatz unter folgenden elektromagnetischen Bedingungen ausgelegt:

E1 (Wohnbereich), E2 (kommerzieller und in beschränktem

Maße industrieller Bereich), E3 (Stadtbereich im Freien) und

E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio)